En Install Guide Ver. 4.3

En Install Guide Ver. 4.3
En
No reproduction in any form of this manual, in whole or in part (except for
brief quotation in critical articles or reviews), may be made without written
authorization from NIKON CORPORATION.
Ver. 4.3 Install Guide
Ver. 4.3
En
Printed in Japan
SB5E00500101(11)
6MSA9711--
Install Guide
Table of Contents
Introduction: About This Manual ....................................................................................................1
Overview ..........................................................................................................................................2
Windows.............................................................................................................................................3
Installing Nikon Capture 4 Under Windows ...................................................................................4
Easy Install ........................................................................................................................................7
Custom Install .................................................................................................................................14
Connecting to a Computer.............................................................................................................21
Uninstall: Uninstalling Nikon Capture 4........................................................................................23
Uninstalling Nikon Capture 4 ..........................................................................................................23
Device Registration.........................................................................................................................24
D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras ................................................................25
D1-Series Cameras ..........................................................................................................................38
Macintosh .........................................................................................................................................69
Installing Nikon Capture 4 on a Macintosh...................................................................................70
Installing Software .........................................................................................................................72
Connecting to a Computer.............................................................................................................78
Uninstall: Uninstalling Nikon Capture 4........................................................................................80
Uninstalling Nikon Capture 4 ..........................................................................................................80
About This Manual
Introduction
About This Manual
Thank you for your purchase of Nikon Capture 4 (Ver. 4.3). This install guide explains how to
install and uninstall Nikon Capture 4 on your Windows or Macintosh computer, and how to
connect your camera to your computer. It also explains how to insert a camera memory card in
a card reader or PC card slot, how to start Nikon Capture 4, and how to register the camera with
the system. Before reading this guide, be sure to read the Nikon Capture 4 User’s Manual.
The procedure for installing Nikon Capture 4 varies with the model of camera and computer
operating system you are using. Be sure to read the sections of this guide that apply to your
model of camera and computer operating system.
1
Introduction
Overview
This guide is divided into two main parts, one for Windows and the other for Macintosh
computers.
Windows
This section explains how to install and uninstall Nikon Capture 4 on your Windows computer,
and how to connect your camera to your computer. It also explains how to insert the memory
card in a card reader or PC card slot. Note that when you connect your camera to a Windows
computer after installing Nikon Capture 4, the computer will automatically identify the camera as a new device and initiate device registration. For information on confirming that the
camera is correctly registered with the system, see “Device Registration” in this manual, which
describes how to confirm device registration with different models of camera and different
versions of Windows.
Macintosh
This section explains how to install and uninstall Nikon Capture 4 on your Macintosh computer,
and how to connect your camera to your computer. It also explains how to insert the memory
card in a card reader or PC card slot.
Illustrations
The illustrations in this guide are from Windows XP and Mac OS X. Depending on the operating system
used, the dialogs and menus displayed on your computer may differ slightly from those shown here.
2
Windows
This section explains how to install and uninstall Nikon
Capture 4, how to connect your camera and insert the camera memory card in a card reader or PC card slot, and how to
register the camera with the system.
3
Windows
Installing Nikon Capture 4 Under Windows
Before installing Nikon Capture 4, make sure that your computer meets the following system
requirements.
Pre-installed versions of Windows XP Home Edition, Windows XP Professional,
Windows 2000 Professional, Windows Millennium Edition (Me), Windows 98
Second Edition (SE)
CPU
300 MHz Pentium equivalent or better
RAM
256 MB (768 MB or more recommended)
Hard-disk space 200 MB required for installation
Video
800 × 600 pixels or more with 16-bit color (High Color/thousands of colors). 24resolution
bit color (True Color/millions of colors) recommended.
IEEE Open Host-Controller Interface (OHCI) compliant IEEE 1394 interface board or
Interface 1394† card‡ required for connection to D1, D1X, and D1H
USB** Built-in USB interface
Supported cameras
D1-series, D2-series, D100, D70s, D70, and D50
(Camera Control)
• CD-ROM drive required for installation.
Other
• Internet connection required for some options.
OS
† The camera may not function as expected when connected to an IEEE 1394 hub.
‡ A list of boards and cards that have been tested and approved for use with the D1, D1X, and D1H is
available on-line at the sites listed page 2 of the User’s Guide.
** The camera may not function as expected when connected to a USB hub or keyboard.
Windows XP Home Edition, Windows XP Professional, Windows 2000 Professional
Installing Nikon Capture 4 under a multi-user operating system requires Administrator privileges. When
installing Nikon Capture 4, log in as:
4
Windows XP Home Edition/Professional
Computer administrator
Windows 2000 Professional
Administrators
Installing Nikon Capture 4 Under Windows
When installing Nikon Capture 4, you can choose between Easy Install and Custom Install
options.
Easy Install
The following software will be installed in the order given below.
1
2
Nikon Mass Storage Camera Drivers
(Windows 98 SE only)
3
Nikon Capture 4
Driver for D1-series cameras
Custom Install
Choose from the following (software will be installed in the order listed):
1
2
Nikon Mass Storage Camera Drivers
(Windows 98 SE only)
3
Nikon Capture 4
Driver for D1-series cameras
Before installing Nikon Capture 4
• Uninstall any earlier versions of Nikon Capture before installing Nikon Capture 4.
• Nikon Capture 4 version 4.3 can be used with either PictureProject or the latest version of Nikon View.
For information on the latest Nikon software, visit the websites listed on page 2 of the Nikon Capture 4
User’s Manual.
• Exit all applications, including any virus-checking software that may be running.
5
Windows
Start the computer and insert the Nikon Capture 4 installer CD in a CD-ROM drive. The Install
Center program will launch automatically. Depending on the country of purchase, a “Select
Region” dialog may be displayed. Select a region and click Next. A language-selection dialog will be displayed; select a language and click Next. The “Install Center” window will be
displayed. The Install Center window contains three tabs: Software, Custom Install, and Customer Support. Clicking Quit will interrupt installation and close the Install Center window.
Software
Clicking the Easy Install button in the Software tab
begins installation of the Nikon Mass Storage Camera
Drivers (Windows 98 SE only), the driver for D1 series
cameras, Nikon Capture 4.
Custom Install
This tab lists the software that can be installed from the
Install Center window. Check the desired items and
click Install to begin installation.
Customer Support
Customer Support
Click the button for your area to view the Nikon technical support web site (Internet connection required).
ReadMe
Click ReadMe to view the ReadMe file. We recommend that you view the ReadMe file before installing
Nikon Capture 4.
If the “Select Region” or “Select Language” Dialog Is Not Displayed
If the Install Center program does not launch automatically when the Nikon Capture 4 CD is inserted:
1. Under Windows XP Home Edition and Windows XP Professional, select My Computer from the Start
menu. In other versions of Windows, double click the My Computer icon on the desktop.
2. Click the icon for the CD-ROM drive containing the Nikon Capture 4 CD with the right mouse button.
3. Choose AutoPlay from the menu that appears.
6
Installing Nikon Capture 4 Under Windows
Easy Install
The standard installation procedure involves two steps: choosing the Easy Install option and
installing the software.
Step 1: Choose the Easy Install option
In the Software tab, click Easy Install to begin installation of the Nikon Mass Stoage Camera
Drivers (Windows 98 SE only), the driver for D1-series cameras, Nikon Capture 4.
Before installation
Before installing Nikon Capture 4 and the device driver, make sure the camera is not connected to the
computer. If the Device Wizard is displayed, click Cancel to exit the Wizard.
Product Key
If prompted to supply a product key when starting Nikon Capture 4 Editor or Nikon Capture 4 Camera
Control, enter the product key supplied on the Nikon Capture 4 CD case.
7
Windows
Step 2: Complete installation
2.1 — Install the driver for D1-series cameras
If you are using one of the D1 series of cameras, first install
the driver for your camera. If you are using a different model
of camera, click Cancel and go to the next step. To install the
driver for D1 series cameras, click OK.
The system will display a message stating that installation is
complete. Click OK.
Windows 98 SE
If you are using Windows 98 SE, the Nikon Mass Storage
Camera Drivers will be installed before the driver for D1 series
cameras. The dialog box shown right will be displayed. Click
OK to continue.
8
Installing Nikon Capture 4 Under Windows
2.2 — Install Nikon Capture 4
Installation of Nikon Capture 4 begins with the license agreement.
2.2.1 — Accept the license agreement
After making sure that you have read and understood the contents of the agreement, click
Yes to continue installation.
2.2.2 — Personalize your copy of Nikon Capture 4
Enter your name and company (if applicable) to activate the Next button. Clicking Next will
display a confirmation dialog; if the information you entered is correct, click Yes to proceed
to the next step.
Earlier Versions of Nikon Capture
Before you can install Nikon Capture 4, you must uninstall any earlier versions of Nikon Capture.
9
Windows
2.2.3 — Choose a location
The folder to which Nikon Capture 4 will be installed is shown in the Destination Folder area
(the default location is …\Program Files\Nikon\NCapture4). To install to this folder, click Next.
To select a new folder, click the Browse… button and navigate to the desired location.
If the chosen folder does not already exist, clicking Next will display the following dialog.
Click Yes to create a folder in the location shown.
2.2.4 — Start installation
While installation is in progress, the dialog shown below will be displayed.
10
Installing Nikon Capture 4 Under Windows
2.2.5 — Create a shortcut on the desktop
When the progress indicator reaches 100%, the dialog shown below will appear. Click Yes to
create a shortcut, allowing you to start Nikon Capture 4 directly from an icon on the desktop.
If you do not want to create a shortcut, click No.
Associating File Extensions with Nikon Capture 4
If Nikon Scan or other software that uses the same file extensions as Nikon Capture is installed, a dialog
will be displayed asking whether you would like to associate Nikon Capture 4 with the extensions for
color balance settings (*.nca), tone curves (*.ncv), and other image adjustment settings files. To associate
Nikon Capture 4 with these extensions (recommended), click Yes.
Choosing an Application for Opening Image Files
If Adobe Photoshop is installed on your system, the dialog for choosing an application for opening image
files will be displayed. Click Yes to select Photoshop as the application that will be used to open image
files.
11
Windows
2.2.6 — Choose default color management settings
To use the color-space profile embedded in images opened in Nikon Capture 4, choose (A)
Use the color space of the file to be opened as the working color space. To choose a
default RGB color-space profile for the working color space in Nikon Capture 4, choose (B)
Always use the default RGB color space as the working color space. When this option
is selected, you can choose the default color-space profile from a pull-down menu. Click OK
to put changes into effect and proceed to the next step.
Clicking About Color Spaces displays a description of the different color-space profiles. Use
this explanation to help you choose a color-space profile.
The default output color-space profile can be changed at any time after installation in the
Color Management tab of the Nikon Capture 4 Editor or Nikon Capture 4 Camera Control
Preferences dialog.
12
Installing Nikon Capture 4 Under Windows
2.2.7 — Complete installation of Nikon Capture 4
The following dialog is displayed when installation of Nikon Capture 4 is complete. Click Finish to proceed to the next step.
2.3 — Restart your computer
The dialog shown below will appear when installation is complete. Click Yes to restart your
computer. This completes the Easy Install procedure.
13
Windows
Custom Install
The standard installation procedure involves two steps: choosing the Custom Install option
and installing the software.
Step 1: Choose the Custom Install option
Click the Custom Install tab and check the software you want to install.
Nikon Mass Storage Camera Drivers
This check box is only displayed under Windows 98 Second Edition (SE). Check this box to
install the Nikon Mass Storage Camera Driver for Windows 98 SE.
Driver for D1 series cameras
Check this box to install the drivers for the D1 series.
Nikon Capture 4
Check this box to install Nikon Capture 4.
Before installation
Before installing Nikon Capture 4 and the device drivers, make sure the camera is not connected to the
computer. If the Device Wizard is displayed, click Cancel to exit the Wizard.
14
Installing Nikon Capture 4 Under Windows
Step 2: Complete installation
To begin installation of the selected software, click the Install button in the Custom Install
tab. If more than one option is selected, the software will be installed in the order listed.
2.1 — Install drivers
If you selected Nikon Mass Storage Camera Drivers (Windows 98 SE only) or Driver for
D1 series cameras, installation will begin with the selected drivers. The explanation that
follows takes the driver for D1-series camera as an example.
2.1.1 — Begin driver installation
If you selected Driver for D1 series cameras, the following dialog will be displayed. Click
OK to begin installation.
2.1.2 — End driver installation
When installation is complete, the following dialog will be displayed. Click OK to proceed to
the next step.
15
Windows
2.2 — Install Nikon Capture 4
Installation of Nikon Capture 4 begins with the license agreement.
2.2.1 — Accept the license agreement
After making sure that you have read and understood the contents of the agreement, click
Yes to continue installation.
2.2.2 — Personalize your copy of Nikon Capture 4
Enter your name and company (if applicable) to activate the Next button. Clicking Next will
display a confirmation dialog; if the information you entered is correct, click Yes to proceed
to the next step.
Earlier Versions of Nikon Capture
Before you can install Nikon Capture 4, you must uninstall any earlier versions of Nikon Capture.
16
Installing Nikon Capture 4 Under Windows
2.2.3 — Choose a location
The folder to which Nikon Capture 4 will be installed is shown in the Destination Folder area
(the default location is …\Program Files\Nikon\NCapture4). To install to this folder, click Next.
To select a new folder, click the Browse… button and navigate to the desired location.
If the chosen folder does not already exist, clicking Next will display the following dialog.
Click Yes to create a folder in the location shown.
17
Windows
2.2.4 — Start installation
While installation is in progress, the dialog shown below will be displayed.
2.2.5 — Create a shortcut on the desktop
When the progress indicator reaches 100%, the dialog shown below will appear. Click Yes to
create a shortcut, allowing you to start Nikon Capture 4 directly from an icon on the desktop.
If you do not want to create a shortcut, click No.
Associating File Extensions with Nikon Capture 4
If Nikon Scan or other software that uses the same file extensions as Nikon Capture is installed, a dialog
will be displayed asking whether you would like to associate Nikon Capture 4 with the extensions for
color balance settings (*.nca), tone curves (*.ncv), and other image adjustment settings files. To associate
Nikon Capture 4 with these extensions (recommended), click Yes.
Choosing an Application for Opening Image Files
If Adobe Photoshop is installed on your system, a dialog will be displayed asking if you want to use Photoshop to open image files saved in Nikon Capture 4. Click Yes to select Photoshop as the application
that will be used to open image files.
18
Installing Nikon Capture 4 Under Windows
2.2.6 — Choose default color management settings
To use the color-space profile embedded in images opened in Nikon Capture 4, choose (A)
Use the color space of the file to be opened as the working color space. To choose a
default RGB color-space profile for the working color space in Nikon Capture 4, choose (B)
Always use the default RGB color space as the working color space. When this option
is selected, you can choose the default color-space profile from a pull-down menu. Click OK
to put changes into effect and proceed to the next step.
Clicking About Color Spaces displays a description of the different color-space profiles. Use
this explanation to help you choose a color-space profile.
The default output color-space profile can be changed at any time after installation in the
Color Management tab of the Nikon Capture 4 Editor or Nikon Capture 4 Camera Control
Preferences dialog.
19
Windows
2.2.7 — Complete installation of Nikon Capture 4
The following dialog is displayed when installation of Nikon Capture 4 is complete. Click Finish to proceed to the next step.
2.3 — Complete installation
The dialog shown below will appear when installation is complete. Click Yes to restart your
computer.
20
Connecting to a Computer
Connecting to a Computer
If you are using a computer running Windows, make sure that you install Nikon Capture 4
before connecting your camera to the computer for the first time. After installing Nikon
Capture 4, turn the camera on and connect it to the computer, or insert the memory card into
a card reader or a PC card slot.
For more information about connecting your camera to a computer, see the documentation
provided with your camera.
D1-Series (IEEE 1394 Interface)
D2-Series/D100 /D70s/D70/D50 (USB Interface)
Use a Reliable Power Source
To ensure that data transfer is not interrupted, be sure that the battery is fully charged. If in doubt,
charge the battery before use or use an AC adapter (available separately). If the battery is exhausted
during transfer, transfer will be interrupted and data may be lost.
21
Windows
Using a PC Card Slot
When inserted in a PC-card adapter (available separately), the camera memory card functions
as a Type II PCMCIA ATA card, allowing images to be read from the card.
Inserting a Memory Card
Remove the memory card from the camera and insert it in the adapter.
Insert the adapter into a PCMCIA TYPE II ATA card slot on your computer. For more information on inserting the adapter, see the documentation provided with your computer.
TM
lash
pactF
Com
AD1
Card EC-
AD
AP
TER
lash
pactF
Com
TM
Card
F
64C
EC-
Depending on your computer’s operating environment, you may need to install software,
register the card adapter, or adjust OS settings when the adapter is inserted into the card slot.
For more information, refer to the instruction manual for your operating system.
Using a Card Reader
Images on the memory card can also be viewed using a card reader.
Inserting a Memory Card
After removing the memory card from the camera, insert it in the card reader and connect
the reader to the computer. See the documentation provided with the card reader for more
information on connecting it to a computer.
Card reader (USB interface)
Card reader
Memory card
22
Uninstall
Uninstall
Uninstalling Nikon Capture 4
This section describes how to uninstall the Windows versions of Nikon Capture 4.
Uninstalling Nikon Capture 4
1
From the Start menu, select All Programs > Nikon
Capture 4 > Nikon Capture 4 Uninstall (Windows XP)
or Programs > Nikon Capture 4 > Nikon Capture 4
Uninstall (other versions of Windows). The uninstall
program will start.
2
The uninstall program will display the message, “Do you want to completely remove the
selected application and all of its components?” Click OK to uninstall Nikon Capture 4.
3
If any of the components used by Nikon Capture 4 are read-only or are used by other
programs, a confirmation dialog will be displayed. Follow the instructions in the dialog to
remove components or leave them untouched.
4
The dialog shown below will be displayed when the uninstall program has finished removing Nikon Capture 4 from your system. Confirm that Yes, I want to restart my
computer now is selected and click Finish to restart your computer.
Windows XP Home Edition, Windows XP Professional, Windows 2000 Professional
Uninstalling Nikon Capture 4 under a multi-user operating system requires Administrator privileges.
When uninstalling Nikon Capture 4, log in as:
Windows XP Home Edition/Professional
Computer administrator
Windows 2000 Professional
Administrators
23
Device Registration
If you connect a supported digital camera to a Windows computer after installing Nikon
Capture 4 and restarting the computer, Windows will automatically identify the camera as a
new device and register the camera with the system. This section explains how to confirm that
the camera is correctly registered. Read the section for your camera and operating system.
Camera
Operating system
Windows XP Home Edition /Professional
D2 series/D100/D70s/D70/D50/COOLPIX Series Windows 2000 Professional
Cameras (USB cameras)
Windows Millennium Edition (Me)
Windows 98 Second Edition (SE)
Windows XP Home Edition /Professional
Windows 2000 Professional
D1-Series Cameras
(Nikon D1/Nikon D1X/Nikon D1H)
Windows Millennium Edition (Me)
Windows 98 Second Edition (SE)
Windows 2000 Professional
Nikon D1 previously registered under Nikon View
Windows Millennium Edition (Me)
DX or Nikon Capture 2 or earlier
Windows 98 Second Edition (SE)
24
25
27
29
31
38
42
53
60
48
57
65
Device Registration: D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
Windows XP Home Edition/Professional
The following explanation uses D100 as an example.
After installing Nikon Capture 4 and restarting the computer,
connect your camera to the computer using a USB cable and
turn the camera on. The camera will be registered automatically.
If the Removable Disk dialog is displayed after registration, click Cancel to close the dialog
box.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Select Control Panel from the Start menu. In the Control Panel window, click the Performance and Maintenance icon to open the Performance and Maintenance window. Click
the System icon in the Performance and Maintenance window to open the System Properties
window. Select the Hardware tab and click the Device Manager button.
Step 2
The Device Manager will be displayed. After confirming that
Disk drives, Storage volumes, and Universal Serial Bus
controllers are listed in the Device Manager, click the plus
sign (+) next to each of these device types.
Logging On
You will need to log on as Computer Administrator to register the camera.
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
25
Windows
Step 3
Confirm that NIKON D100 USB Device, Generic Volume,
and USB Mass Storage Device are listed respectively under
Disk drives, Storage volumes, and Universal Serial Bus
controllers. Double-click each of these listings to open the
associated Properties window.
If the NIKON D100 USB Device is listed under Other devices, delete this entry and then turn the camera off and
then on again.
Step 4
The Properties dialogs for the selected devices will be displayed. Click the General tab and
confirm that This device is working properly appears under Device status. Click OK.
Device registration is now complete. Click OK to close the System Properties dialog.
PTP
If the USB option in the camera setup menu is set to PTP, confirm that the camera is listed in the Control
Panel under Printers and Other Hardware > Scanners and Cameras.
26
Device Registration: D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
Windows 2000 Professional
The following explanation uses D100 as an example.
After installing Nikon Capture 4 and restarting
the computer, connect your camera to the
computer using a USB cable and turn the
camera on. The camera will be registered
automatically.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Right-click the My Computer icon on the
desktop. Open the System Properties dialog
by selecting Properties from the menu that
appears. Open the Hardware tab and click
the Device Manager… button in the Device
Manager area.
Step 2
The Device Manager will be displayed. After
confirming that Disk drives, Storage volumes, and Universal Serial Bus controllers
are listed in the Device Manager, click the plus
sign (+) next to each of these device types.
Logging On
Log on as Administrators to register the camera.
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
27
Windows
Step 3
Confirm that NIKON D100 USB Device,
Generic volume, and USB Mass Storage Device are listed respectively under Disk drives,
Storage volumes, and Universal Serial Bus
controllers. Double-click each of these listings
to open the associated Properties window.
If the NIKON D100 USB Device is listed under
Other devices, delete this entry and then turn
the camera off and then on again.
Step 4
The Properties dialogs for the selected devices will be displayed. Click the General tab and
confirm that This device is working properly appears under Device status. Click OK.
Device registration is now complete. Click OK to close the System Properties dialog.
PTP
If the USB option in the camera setup menu is set to PTP, confirm that the camera is listed in the Scanners
and Cameras Control Panel. The camera may be listed by name or as a Nikon DSLR camera.
28
Device Registration: D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
Windows Millennium Edition (Me)
The following explanation uses D100 as an example.
After installing Nikon Capture 4 and restarting
the computer, connect your camera to the
computer using a USB cable and turn the
camera on. The camera will be registered
automatically.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Right-click the My Computer icon on the
desktop. Open the System Properties dialog
by selecting Properties from the menu that
appears. Click the Device Manager tab.
Step 2
After confirming that Disk drives, Storage
de vice, and Universal Se ri al Bus controllers are listed in the Device Manager tab,
click the plus sign (+) next to each of these
device types.
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
29
Windows
Step 3
Confirm that NIKON D100, USB Disk, and USB Mass Storage Device are listed respectively
under Disk drives, Storage device, and Universal Serial Bus controllers. Double-click
each of these listings to display the associated Properties window.
If the NIKON D100 is listed under Other devices, delete this entry and then turn the camera
off and then on again.
Step 4
The Properties dialogs for the selected devices will be displayed. Click the General tab and
confirm that This device is working properly appears under Device status. Click OK.
Device registration is now complete. Click OK to close the System Properties dialog.
PTP
If the USB option in the camera setup menu is set to PTP, confirm that the camera is listed in the Scanners
and Cameras Control Panel. The camera may be listed by name or as a Nikon DSLR camera.
30
Device Registration: D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
Windows 98 Second Edition (SE)
The following explanation uses D100 as an example.
After installing Nikon Capture 4 and restarting
the computer, connect your camera to the
computer using a USB cable and turn the
camera on. The camera will be registered
automatically.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Right-click the My Computer icon on the
desktop and select Properties from the menu
that appears. The System Properties dialog will
be displayed. Click the Device Manager tab.
Step 2
After confirming that Disk drives, Hard disk
controllers, and Universal Serial Bus controllers are listed in the Device Manager tab,
click the plus sign (+) next to each of these
device types.
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
31
Windows
Step 3
Confirm that NIKON D100, Nikon Digital Camera Controller, and Nikon Digital Camera
Mass Storage Driver are listed respectively under Disk drives, Hard disk controllers, and
Universal Serial Bus controllers. Double-click each of these listings to open the associated
Properties window.
If the Nikon D100 is listed under Other devices, reinstall the device driver as instructed
in “Reinstalling the Device Driver” (
33).
If the three drivers above are not listed in the Device Manager and NIKON D100 is not listed
under Other devices, disconnect the camera and restart the computer. When the computer
has restarted, reconnect the camera to the computer.
Step 4
The properties for the selected devices will be displayed. Click the General tab and confirm
that This device is working properly appears under Device status. Click OK.
Device registration is now complete. Click OK to close the System Properties dialog.
PTP
If the USB option in the camera setup menu is set to PTP, confirm that the camera is listed in the Scanners
and Cameras Control Panel. The camera may be listed by name or as a Nikon DSLR camera.
32
Device Registration: D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
Reinstalling the Device Driver — Windows 98 Second Edition (SE)
If NIKON D100 is listed under Other devices, you will need to reinstall the device driver.
Step 1
Double-click the NIKON D100 listing under
Other devices.
Step 2
The NIKON D100 Properties dialog will be
displayed. Open the General tab and click
Reinstall Driver.
Step 3
The Update Device Driver Wizard will be displayed; click Next.
33
Windows
Step 4
The dialog box shown at right will be displayed. Select Search for a better driver
than the one your device is using now
and click Next.
Step 5
Insert the Nikon Capture 4 CD into a CD-ROM
drive. To prevent the Select Language dialog
from opening automatically, hold down the
shift key while inserting the CD. Check the
CD-ROM drive option and click Next.
The Select Language Dialog
If the Select Language dialog appears when
the CD is inserted, click Quit to close the
dialog.
Step 6
The dialog shown at right will be displayed.
Click Next.
No Driver Found
If a message is displayed stating that Windows
was unable to find a suitable driver, this may
indicate that the Nikon Capture 4 CD was not
correctly inserted in the CD-ROM drive or that
the appropriate check box was not selected.
Click Back to return to the dialog shown in Step
5, and confirm that your settings are correct.
34
Device Registration: D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
Step 7
A dialog will be displayed indicating that driver
update was successful. Click Finish to close
the dialog.
Step 8
Click the General tab in the Nikon Digital Camera Mass Storage Driver dialog and confirm
that This device is working properly appears
under Device status. Click Close.
Step 9
The wizard will now start installation of the
Nikon Digital Camera Controller with the dialog
shown at right. Click Next.
35
Windows
Step 10
Select Search for the best driver for your
device and click Next.
Step 11
After confirming that the Nikon Capture 4 CD
is inserted in the CD-ROM drive, check the
CD-ROM drive option and click Next.
Step 12
A dialog will be displayed stating that
Windows has found the drivers for “Nikon
Digital Camera Controller”; click Next.
No Driver Found
If a message is displayed stating that Windows
was unable to find a suitable driver, this may
indicate that the Nikon Capture 4 CD was not
correctly inserted in the CD-ROM drive or that
the appropriate check box was not selected.
Click Back to return to the dialog shown in
Step 11, and confirm that your settings are
correct.
36
Device Registration: D2-Series/D100/D70s/D70/D50/COOLPIX-Series Cameras
Step 13
A dialog will be displayed indicating that driver
update was successful. Click Finish to close
the dialog.
Step 14
Click OK to close the System Properties
dialog.
37
Windows
D1-Series Cameras
Windows XP Home Edition/Professional
Before You Begin
Confirm that your OHCI-compliant IEEE 1394 interface board or card has been correctly registered with the system.
Select Control Panel from the Start menu. In the
Control Panel window, click the Performance
and Maintenance icon to open the Performance and Maintenance window. Click the
System icon in the Performance and Maintenance window to open the System Properties
window. Select the Hardware tab and click
the Device Manager button to open Device
Manager window shown at right.
The bus controller for
your IEEE 1394 board
or card should be listed
un der “1394 Bus host
controllers.”
If “IEEE 1394 Bus host controllers” is not listed in the Device Manager, or if your IEEE 1394
interface board or card is listed as an unknown or miscellaneous device or is preceded by a
red or yellow warning icon, follow the instructions in the manual provided with the board to
ensure that the drivers are properly installed.
After installing Nikon Capture 4 and restarting the computer, connect your camera to the
computer using an IEEE 1394 cable and turn the camera on. The camera will be registered
automatically.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Select Control Panel from the Start menu
to open the Control Panel window. Click
the Performance and Maintenance icon
inside the Control Panel window to open the
Performance and Maintenance window. Click
the System icon inside the Performance and
Maintenance window to open the System
Properties window. Select the Hardware
tab and click the Device Manager button
to open Device Manager window. After confirming that “Nikon 1394 Protocol Device” is
listed in the Device Manager, click the “+”
sign to its left.
Logging On
You will need to log on as the “Computer Administrator” to register your camera.
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
38
Device Registration: D1-Series Cameras
If no “Nikon 1394 Protocol Device” listing appears or if “NIKON D1X” (or “D1” or “D1H”)
is listed under Other Devices, reinstall the
device driver as instructed in “Reinstalling the
Device Driver” ( 40).
If “Nikon 1394 Protocol Device” is not listed
in the Device Manager and “NIKON D1X” (or
“D1” or “D1H”) is not listed under Other Devices, disconnect the camera, and restart the
computer. When the computer has restarted,
reconnect the camera.
Step 2
After confirming that “Nikon Digital Camera
D1 Series” is listed under “Nikon 1394 Protocol
Device,” double-click the listing to open the
Properties window.
Step 3
The Nikon Digital Camera D1 Series Properties
dialog will be displayed. Click the General
tab and confirm that “This device is working
properly” appears under “Device status”.
Click OK.
Close the Device Manager, then click OK to close the System Properties window. Device
registration is now complete.
39
Windows
Reinstalling the Device Driver — Windows XP Home Edition /Professional
If “NIKON D1X” (or “D1” or “D1H”) appears under “Other Devices,” reinstall the device
driver as instructed below.
Step 1
Open the Device Manager dialog. Doubleclick the listing for the Nikon D1X (or D1 or
D1H) that appears under “Other devices.” The
Properties dialog will be displayed.
Step 2
Open the General tab and click Reinstall
Driver… .
Step 3
The “Hardware Update Wizard” dialog will
appear. Holding down the shift key to prevent the Select Language dialog from opening
automatically, insert the Nikon Capture 4 CD
into the CD-ROM drive. (If the shift key is
not held down, the Select Language dialog
will appear when the CD-ROM is inserted.)
Select Install the software automatically
and click Next.
40
Device Registration: D1-Series Cameras
Step 4
When the driver installation has been completed, the dialog shown at right will be displayed; click Finish to close the wizard.
Step 5
Confirm that “This device is working properly”
appears under “Device status” in the General
Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.
Step 6
Close the Device Manager, then click OK to close
the System Properties window.
41
Windows
Windows 2000 Professional
Before You Begin
Confirm that your OHCI-compliant IEEE 1394 interface board or card has been correctly registered with the system.
Click the My Computer icon on the desktop
with the right mouse button and select Properties from the menu that appears to display the
System Properties dialog. Open the Hardware
tab and click the Device Manager… button
in the Device Manager section.
The bus controller for
your IEEE 1394 board
or card should be listed
un der “1394 Bus host
controllers.”
If “1394 Bus host controllers” does not appear in the Device Manager, or if your IEEE 1394
interface board or card is listed as an unknown or miscellaneous device or is preceded by a
red or yellow warning icon, follow the instructions in the manual provided with the board to
ensure that the drivers are properly installed.
After installing Nikon Capture 4 and restarting the computer, connect your camera to the
computer using an IEEE 1394 cable and turn on the camera. The camera is registered automatically.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Once registration is complete, check that
the D1X (or D1 or D1H) has been correctly
registered with the system. Click the My
Com put er icon on the desk top with the
right mouse button and select Properties
from the menu that appears to display the
System Properties dialog. Open the Hardware
tab and click the Device Manager… button
in the Device Manager section.
Logging On
You will need to log on as “Administrators” to register the D1, D1X, or D1H.
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
Updating the Drivers for the D1
If you are already using the D1 with Nikon View DX or an earlier version of Nikon Capture, you will need
48).
to update the camera drivers as described under “Updating the Drivers for the D1” (
42
Device Registration: D1-Series Cameras
Step 2
The Device Manager will be displayed. After
confirming that “Nikon 1394 Protocol Device”
is listed in the Device Manager, click the “+”
sign to its left.
If no “Nikon 1394 Protocol Device” listing appears or if “NIKON D1X” (or “D1” or “D1H”)
is listed under Other Devices, reinstall the
device driver as instructed in “Reinstalling the
Device Driver” ( 44).
If “Nikon 1394 Protocol Device” is not listed
in the Device Manager and “NIKON D1X” (or
“D1” or “D1H”) is not listed under Other Devices, disconnect the camera, and restart the
computer. When the computer has restarted,
reconnect the camera.
Step 3
After confirming that “Nikon Digital Camera
D1 Series” is listed under “Nikon 1394 Protocol Device,” double-click the listing to open
the Properties window.
43
Windows
Step 4
The Nikon Digital Camera D1 Series Properties
dialog will be displayed. Click the General
tab and confirm that “This device is working
properly” appears under “Device status”.
Click OK.
Close the Device Manager, then click OK to close the System Properties window. Device
registration is now complete.
Reinstalling the Device Driver — Windows 2000 Professional
If “Nikon 1394 Protocol Device” is listed under “Other Devices,” reinstall the device driver as
described below.
Step 1
Click the My Computer icon on the desktop
with the right mouse button and select Properties from the menu that appears to display
the System Properties dialog. Open the Hardware tab and click the Device Manager…
button in the Device Manager section.
44
Device Registration: D1-Series Cameras
Step 2
The Device Manager will be displayed. Double-click the listing for the Nikon D1X (or D1
or D1H) that appears under “Other Devices”
or “Miscellaneous Devices.”
Step 3
Open the General tab and click Reinstall
Driver….
Step 4
The Upgrade Device Driver Wizard will be
displayed; click Next.
45
Windows
Step 5
Select the search option and click Next.
Step 6
The dialog shown at right will be displayed.
Holding down the shift key to prevent the
Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into
the CD-ROM drive. Select CD-ROM drives
and click Next.
The Select Language Dialog
If the Select Language dialog appears when
the CD is inserted, click the Quit button to
close the dialog.
Step 7
The dialog shown at right will be displayed;
click Next.
No Driver Found
If the message, “Windows was unable to find
a suitable driver for this device,” is displayed,
this may indicate that the Nikon Capture 4
CD was not correctly inserted in the CD-ROM
drive or that the correct search location was
not specified. Click Back to return to the dialog shown in Step 6, where you can confirm
that the correct location has been specified.
46
Device Registration: D1-Series Cameras
Step 8
The dialog shown at right will be displayed; click Finish.
Step 9
Confirm that “This device is working properly”
appears under “Device status” in the General
Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.
Step 10
Close the Device Manager, then click OK to
close the System Properties window.
47
Windows
Updating the Drivers for the D1 — Windows 2000 Professional
If you are already using the D1 with Nikon View DX or Nikon Capture, you will need to update
the camera driver.
Step 1
Click the My Computer icon on the desktop
with the right mouse button and select Properties from the menu that appears to display the
System Properties dialog. Open the Hardware
tab and click the Device Manager… button
in the Device Manager section.
Step 2
The Device Manager will be displayed. Under
the entry “Nikon 1394 Device,” double-click
“Nikon Digital Camera D1.”
Step 3
The Nikon Digital Camera D1 Properties dialog
will be displayed. Open the Driver tab and
click Update Driver….
Logging On
You will need to log on as “Administrators” to update the device drivers.
48
Device Registration: D1-Series Cameras
Step 4
The Upgrade Device Driver Wizard will be
displayed; click Next.
Step 5
The dialog shown at right will be displayed.
Select the search option and click Next.
Step 6
The dialog shown at right will be displayed.
Holding down the shift key to prevent the
Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into
the CD-ROM drive. Select CD-ROM drives
and click Next.
The Select Language Dialog
If the Select Language dialog appears when
the CD is inserted, click the Quit button to
close the dialog.
49
Windows
Step 7
The dialog shown at right will be displayed.
Select “Install one of the other drivers” and
click Next.
Step 8
Select Nikon Digital Camera D1 Series from the
dialog at right and click Next.
Step 9
The dialog shown at right will be displayed;
click Finish.
50
Device Registration: D1-Series Cameras
Step 10
Confirm that “This device is working properly”
appears under “Device status” in the General
Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.
Step 11
Close the Device Manager, then click OK to close
the System Properties window.
51
Windows
Troubleshooting
• If “1394 Bus host Controller” is not displayed in the Device Manager, if the IEEE 1394 board
or card is listed under “Other Devices” or “Miscellaneous Devices,” or if the listing for the
IEEE 1394 board or card is preceded by a red or yellow warning icon…
…the computer does not recognize the IEEE 1394 board or card. Refer to the documentation
provided with your computer or IEEE 1394 board or card for information on registering the
board or card with the system.
• If “1394 Bus host Controller” is listed in the Device Manager but the entry for the Nikon
D1 (or D1X or D1H) does not appear…
…check the following:
• Is the camera on?
• Is the battery fully charged? If you are using an AC adapter (available separately), is it
properly connected?
• Is the mode dial set to “PC”?
• Is the IEEE 1394 cable properly connected?
52
Device Registration: D1-Series Cameras
Windows Millennium Edition (Me)
Before You Begin
Confirm that the OHCI-compliant IEEE 1394 interface board has been correctly registered
with the system.
Click the My Computer icon on the desktop with the right mouse button and select
Properties from the menu that appears. The
System Properties dialog will be displayed; click
the Device Manager tab.
The bus controller for your
IEEE 1394 board or card
should be listed under “1394
Bus Controller.”
If “1394 Bus Controller” is not listed in the Device Manager, or if your IEEE 1394 interface
board or card is listed as an unknown or miscellaneous device or is preceded by red or yellow
warning icons, follow the instructions in the manual provided with the board to ensure that
the drivers are properly installed.
After installing Nikon Capture 4 and restarting the computer, connect your camera to the
computer using an IEEE 1394 cable and turn on the camera. The camera will be registered
automatically.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Once registration is complete, check that the
D1X (or D1 or D1H) has been correctly registered with the system. Click the My Computer
icon on the desktop with the right mouse button and select Properties from the menu that
appears. The System Properties dialog will be
displayed; click the Device Manager tab.
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
Updating the Drivers for the D1
If you are already using the D1 with Nikon View DX or Nikon Capture, you will need to update the camera
drivers as described in “Updating the Drivers for the D1” (
57).
53
Windows
Step 2
The Device Manager sheet will be displayed.
After confirming that “Nikon 1394 Protocol
Device” is listed in the Device Manager, click
the “+” sign to its left.
If no “Nikon 1394 Protocol Device” listing appears or if “NIKON D1X” (or “D1” or “D1H”)
is listed under Other Devices, reinstall the
device driver as instructed in “Reinstalling the
Device Driver” ( 55).
If “Nikon 1394 Protocol Device” is not listed in the Device Manager and “NIKON D1X” (or
“D1” or “D1H”) is not listed under Other Devices, disconnect the camera, and restart the
computer. When the computer has restarted, reconnect the camera to the computer.
Step 3
After confirming that “Nikon Digital Camera
D1 Series” is listed under “Nikon 1394 Protocol
Device,” double click the listing to open the
Properties window.
Step 4
The Nikon Digital Camera D1 Series Properties
dialog will be displayed. Click the General
tab and confirm that “This device is working
properly” appears under “Device status.”
Click OK.
Click OK to close the System Properties window. Device registration is now complete.
54
Device Registration: D1-Series Cameras
Reinstalling the Device Driver — Windows Millennium Edition (Me)
If “Nikon 1394 Protocol Device” is listed Other Devices, reinstall the device driver as described
below.
Step 1
Click the My Computer icon on the desktop with the right mouse button and select
Properties from the menu that appears. The
System Properties dialog will be displayed; click
the Device Manager tab.
Step 2
The Device Manager sheet will be displayed.
Double-click the listing for the Nikon D1X (or
D1 or D1H) that appears under “Other Devices”
or “Miscellaneous Devices.”
Step 3
The NIKON D1X (or D1 or D1H) Properties
dialog will be displayed. Open the General
tab and click Reinstall Driver….
Step 4
The Update Device Driver Wizard will be displayed. Holding down the shift key to prevent
the Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into
the CD-ROM drive. Confirm that “Automatic
search for a better driver (Recommended)”
is selected and click Next. The wizard will
automatically update the device drivers.
The Select Language Dialog
If the Select Language dialog appears when
the CD is inserted, click the Quit button to
close the dialog.
55
Windows
Step 5
The dialog shown at right will be displayed;
click Finish.
Step 6
Confirm that “This device is working properly”
appears under “Device status” in the General
Tab of the Nikon Digital Camera D1 Series Properties dialog. Click Close.
Step 7
Click Close to close the System Properties
window.
56
Device Registration: D1-Series Cameras
Updating the Drivers for the D1 — Windows Millennium Edition (Me)
If you are already using the D1 with Nikon View DX or Nikon Capture, you will need to update
the camera driver.
Step 1
Click the My Computer icon on the desktop with the right mouse button and select
Properties from the menu that appears. The
System Properties dialog will be displayed; click
the Device Manager tab.
Step 2
The Device Manager sheet will be displayed.
Under the entry “Nikon 1394 Device,” doubleclick “Nikon Digital Camera D1.”
Step 3
The Nikon Digital Camera D1 Series Properties
dialog will be displayed. Open the Driver tab
and click Update Driver….
Step 4
The Update Device Driver Wizard will be displayed. Holding down the shift key to prevent
the Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into
the CD-ROM drive, select “Automatic Search
for a Better Driver (Recommended),” and click
Next. The wizard will automatically update
the device drivers.
The Select Language Dialog
If the Select Language dialog appears when
the CD is inserted, click the Quit button to
close the dialog.
57
Windows
Step 5
The dialog shown below will be displayed. Select the driver located at “(Drive letter for CDROM drive):\” and click OK.
Step 6
The dialog shown at right will be displayed;
click Finish.
Step 7
Confirm that “This device is working properly”
appears under “Device status” in the General
Tab of the Nikon Digital Camera D1 Series
Properties dialog. Click Close.
58
Device Registration: D1-Series Cameras
Step 8
Click Close to close the System Properties
window.
Troubleshooting
• If “1394 Bus Controller” is not displayed in the Device Manager, if the IEEE 1394 board
or card is listed under “Other Devices” or “Miscellaneous Devices,” or if the listing for the
IEEE 1394 board or card is preceded by a red or yellow warning icon…
…the computer does not recognize the IEEE 1394 board or card. Refer to the documentation
provided with your computer or IEEE 1394 board or card for information on registering the
board or card with the system.
• If “1394 Bus Controller” is listed in the Device Manager but the entry for the Nikon D1X
(or D1 or D1H) does not appear…
…check the following:
• Is the camera on?
• Is the battery fully charged? If you are using an AC adapter (available separately), is it
properly connected?
• Is the mode dial set to “PC”?
• Is the IEEE 1394 cable properly connected?
59
Windows
Windows 98 Second Edition (SE)
Before You Begin
Confirm that your OHCI-compliant IEEE 1394 interface board or card has been correctly registered with the system.
Click the My Computer icon on the desktop with the right mouse button and select
Properties from the menu that appears. The
System Properties dialog will be displayed; click
the Device Manager tab.
The bus controller for your
IEEE 1394 board or card
should be listed under “1394
Bus Controller.”
If “1394 Bus Controller” is not listed in the Device Manager, or if your IEEE 1394 interface
board or card is listed as an unknown or miscellaneous device or is preceded by a red or yellow
warning icon, follow the instructions in the manual provided with the board to ensure that
the drivers are properly installed.
After installing Nikon Capture 4 and restarting the computer, connect your camera to the
computer using an IEEE 1394 cable and turn on the camera. The camera is registered automatically.
Follow the instructions below to check that the camera has been correctly registered with the
system.
Step 1
Once registration is complete, check that the
D1X (or D1 or D1H) has been correctly registered
with the system. Click the My Computer icon
on the desktop with the right mouse button
and select Properties from the menu that
appears. The System Properties dialog will be
displayed; click the Device Manager tab.
Updating the Drivers for the D1
If you are already using the D1 with Nikon View DX or an earlier version of Nikon Capture, you will need
to update the camera drivers as described in “Updating the Drivers for the D1” (
65).
Before Connecting the Camera
Be sure to install Nikon Capture 4 before connecting your camera to the computer.
60
Device Registration: D1-Series Cameras
Step 2
The Device Manager sheet will be displayed.
After confirming that “Nikon 1394 Protocol
Device” is listed in the Device Manager, click
the “+” sign to its left.
If no “Nikon 1394 Protocol Device” listing appears or if “NIKON D1X” (or “D1” or “D1H”)
is listed under Other Devices, reinstall the
device driver as instructed in “Reinstalling the
Device Driver” ( 62).
If “Nikon 1394 Protocol Device” is not listed in the Device Manager and “NIKON D1X” (or
“D1” or “D1H”) is not listed under Other Devices, disconnect the camera, and restart the
computer. When the computer has restarted, reconnect the camera to the computer.
Step 3
After confirming that “Nikon Digital Camera
D1 Series” is listed under “Nikon 1394 Protocol Device,” double click the listing to open
the Properties window.
Step 4
The Nikon Digital Camera D1 Series Properties
dialog will be displayed. Click the General
tab and confirm that “This device is working
properly” appears under “Device status.”
Click OK.
Click OK to close the System Properties window. Device registration is now complete.
61
Windows
Reinstalling the Device Driver — Windows 98 Second Edition (SE)
If “Nikon 1394 Protocol Device” is listed under Other Devices, reinstall the device driver as
described below.
Step 1
Click the My Computer icon on the desktop with the right mouse button and select
Properties from the menu that appears. The
System Properties dialog will be displayed; click
the Device Manager tab.
Step 2
The Device Manager sheet will be displayed.
Double-click the listing for the Nikon D1X (or
D1 or D1H) that appears under “Other Devices” or “Miscellaneous Devices.”
Step 3
The NIKON D1X (or D1 or D1H) Properties
dialog will be displayed. Open the General
tab and click Reinstall Driver.
Step 4
The Update Device Driver Wizard will be displayed; click Next.
62
Device Registration: D1-Series Cameras
Step 5
The dialog shown at right will be displayed.
Select “Search for a better driver than the one
your device is using now. (Recommended)”
and click Next.
Step 6
The dialog shown at right will be displayed.
Holding down the shift key to prevent the
Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into
the CD-ROM drive. Select CD-ROM drive
and click Next .
The Select Language Dialog
If the Select Language dialog appears when
the CD is inserted, click the Quit button to
close the dialog.
Step 7
A dialog will be displayed stating that Windows has found the drivers for “Nikon Digital
Camera D1 Series”; click Next.
No Driver Found
If the message, “Windows was unable to find
a suitable driver for this device,” is displayed,
this may indicate that the Nikon Capture 4 CD
was not correctly inserted in the CD-ROM drive
or that the correct search location was not
specified. Click Back to return to the dialog
shown in Step 6, where you can confirm that
the correct location has been specified.
63
Windows
Step 8
The dialog shown at right will be displayed;
click Finish.
Step 9
Confirm that “This device is working properly”
appears under “Device status” in the General
Tab of the Nikon Digital Camera D1 Series
Properties dialog. Click Close.
Step 10
Click Close to close the System Properties
window.
64
Device Registration: D1-Series Cameras
Updating the Drivers for the D1 — Windows 98 Second Edition (SE)
If you are already using the D1 with Nikon View DX or Nikon Capture, you will need to update
the camera driver.
Step 1
Click the My Computer icon on the desktop with the right mouse button and select
Properties from the menu that appears. The
System Properties dialog will be displayed; click
the Device Manager tab.
Step 2
The Device Manager sheet will be displayed.
Under the entry “Nikon 1394 Device,” doubleclick “Nikon Digital Camera D1.”
Step 3
The Nikon Digital Camera D1 Series Properties
dialog will be displayed. Open the Driver tab
and click Update Driver….
Step 4
The Update Device Driver Wizard will be displayed; click Next.
65
Windows
Step 5
The dialog shown at right will be displayed.
Select “Search for a better driver than the one
your device is using now. (Recommended)”
and click Next.
Step 6
The dialog shown at right will be displayed.
Holding down the shift key to prevent the
Select Language dialog from opening automatically, insert the Nikon Capture 4 CD into
the CD-ROM drive. Select CD-ROM drive
and click Next.
The Select Language Dialog
If the Select Language dialog appears when
the CD is inserted, click the Quit button to
close the dialog.
Step 7
A dialog will be displayed stating that
Windows has found the drivers for “Nikon
Digital Camera D1 Series.” Click Next.
No Driver Found
If the message, “Windows was unable to find
a suitable driver for this device,” is displayed,
this may indicate that the Nikon Capture 4 CD
was not correctly inserted in the CD-ROM drive
or that the correct search location was not
specified. Click Back to return to the dialog
shown in Step 6 where you can confirm that
the correct location has been specified.
66
Device Registration: D1-Series Cameras
Step 8
The dialog shown at right will be displayed;
click Finish.
Restart
If a message is displayed prompting you to
restart Windows, click Restart.
Step 9
Confirm that “This device is working properly”
appears under “Device status” in the General
Tab of the Nikon Digital Camera D1 Series
Properties dialog. Click Close.
Step 10
Click Close to close the System Properties
window.
67
Windows
Troubleshooting
• If “1394 Bus Controller” is not displayed in the Device Manager, if the IEEE 1394 board
or card is listed under “Other Devices” or “Miscellaneous Devices,” or if the listing for the
IEEE 1394 board or card is preceded by a red or yellow warning icon…
…the computer does not recognize the IEEE 1394 board or card. Refer to the documentation
provided with your computer or IEEE 1394 board or card for information on registering the
board or card with the system.
• If “1394 Bus Controller” is listed in the Device Manager but the entry for the Nikon D1X
(or D1 or D1H) does not appear…
…check the following
• Is the camera on?
• Is the battery fully charged? If you are using an AC adapter (available separately), is it
properly connected?
• Is the mode dial set to “PC”?
• Is the IEEE 1394 cable properly connected?
68
Macintosh
This section explains how to install and uninstall Nikon
Capture 4, and how to connect your camera and insert the
camera memory card in a card reader or PC card slot.
69
Macintosh
Installing Nikon Capture 4 on a Macintosh
Before installing Nikon Capture 4, make sure that your computer meets the following system
requirements.
OS
Model
RAM
Mac OS 9.0.4–9.2.2*, Mac OS X (version 10.1.5 or later)
Built-in USB or FireWire port required
• Mac OS X: 256 MB (768 MB or more recommended)
• Mac OS 9: memory allocation of 64 MB or more to Nikon Capture 4 Camera
Control, 512 MB or more to Nikon Capture 4 Editor
200 MB required for installation
800 × 600 pixels or more with 16-bit color (High Color/thousands of colors). 24bit color (True Color/millions of colors) recommended.
Hard-disk space
Video
resolution
Fire
Built-in FireWire interface required for connection to D1, D1X, and D1H
Wire†
Interface
• Built-in USB interface
USB** • RATOC REX-PCIU3U USB interface board (USB 2.0; for use only with D2-series
under Mac OS X)
Supported cameras
D2-series, D1-series, D100††, D70s, D70, and D50
(Camera Control)
• CD-ROM drive required for installation.
Other
• Internet connection required for some options.
* With CarbonLib version 1.6 or later.
† The camera may not function as expected when connected to an FireWire hub.
** The camera may not function as expected when connected to a USB hub or keyboard.
†† Camera firmware version 2.00 or later.
Before installing Nikon Capture 4
Before installing Nikon Capture 4:
• Uninstall any earlier versions of Nikon Capture.
• Nikon Capture 4 version 4.3 can be used with either PictureProject or the latest version of Nikon View.
For information on the latest Nikon software, visit the websites listed on page 2 of the Nikon Capture 4
User’s Manual.
• Exit all applications, including any virus-checking software that may be running.
Before Starting Nikon Capture 4 Camera Control (D2-series / D100/D70s/D70/D50 Only)
If you are using a D2-series, D100, D70s, D70 or D50 digital camera, set the USB option in the camera
setup menu to PTP before starting Nikon Capture 4 Camera Control.
Mac OS X
The administrator password is required when installing Nikon Capture 4 under Mac OS X.
70
Installing Nikon Capture 4 on a Macintosh
Start the computer and insert the Nikon Capture 4 installer CD in a CD-ROM drive. Doubleclick the Nikon Capture 4 CD-ROM icon on the desktop, then double-click the Welcome icon.
Depending on the country of purchase, a “Select Region” dialog may be displayed. Select a
region and click Next. A language-selection dialog will be displayed; select a language and
click Next. The “Install Center” window will be displayed. The Install Center window contains
the following tabs. To interrupt installation and close the Install Center window, click Quit.
Software
Click Install to install Nikon Capture 4.
Custom Install
Install selected software. Check Nikon Capture 4
and click Install to install the selected software.
Customer Support
Customer Support
Click the appropriate button to open your web
browser to the Nikon Customer Support web site
for your area (Internet connection required).
Display README file
Click Display README file to view the ReadMe
file. We recommend that you view the ReadMe
file before installing Nikon Capture 4.
71
Macintosh
Installing Software
If you are installing software from the Software tab, you can begin installation simply by clicking the Install button. If you are installing software from the Custom Install tab, you have to
go through two steps: selecting the software and installing the software.
Step 1: Select software
Select the programs you want to install from the list in the Custom Install tab.
Nikon Capture 4
Check this option to install Nikon Capture 4.
Software tab
Custom Install tab
Step 2: Install software
To begin installation, click Install. If more than one item is selected in the Custom Install tab,
software will be installed in the order listed.
Product Key
If prompted to supply a product key when starting Nikon Capture 4 Editor or Nikon Capture 4 Camera
Control, enter the product key supplied on the Nikon Capture 4 CD case.
72
Installing Nikon Capture 4 on a Macintosh
2.1 — Install Nikon Capture 4
If you opted to install Nikon Capture 4, it will be installed first.
2.1.1 — Start the installer
Installation of Nikon Capture 4 opens with the dialog shown below.
Click Continue… to start the installer.
2.1.2 — Accept the license agreement
The license agreement will be displayed. After making sure that you have read and understood the contents of the agreement, click Accept to continue installation.
The ReadMe file will then be displayed. Take a few moments to view this file, which may
contain important information that could not be included in the manual.
After viewing the ReadMe file, click Continue….
Installing Nikon Capture 4 under Mac OS X
The administrator password is required when installing Nikon Capture 4 under Mac OS X.
73
Macintosh
2.1.3 — Choose Easy Install
Choose Easy Install from the pull-down
menu in the top left corner of the Nikon
Capture Installer dialog.
2.1.4 — Confirm the install destination
The disk and folder to which Nikon Capture 4
will be installed are listed under “Install Location.”
2.1.5 — Start the installer
Click Install in the Nikon Capture Installer dialog to begin installation of Nikon Capture 4.
A progress meter will be displayed during
installation.
Earlier Versions of Nikon Capture
Before you can install Nikon Capture 4, you must uninstall any earlier versions of Nikon Capture.
Create Aliases (Mac OS 9 Only)
After you click Install in the Nikon Capture Installer dialog, a dialog will be displayed asking whether you wish to create aliases for
Nikon Capture 4 Editor and Nikon Capture 4 Camera Control on
the desktop. Click Yes to create these aliases, or No to exit without
creating aliases.
74
Installing Nikon Capture 4 on a Macintosh
2.1.6 — Selecting a Plug-ins Folder (Mac OS 9)
If multiple copies of Photoshop are installed, a selection dialog will be displayed. Choose
a destination for the Nikon NEF plug-in from the listed copies of Photoshop and click Continue.
2.1.7 — Personalize your copy of Nikon Capture 4
Enter your name and company (if applicable)
to personalize your copy of Nikon Capture 4.
Clicking OK will display a confirmation dialog; if the information you entered is correct, click Yes to proceed to the next step.
To change the information you entered, click
No.
2.1.8— Choose default color management settings
To use the color-space profile embedded in
images opened in Nikon Capture 4, choose
(A) Use the color space of the file to
be opened as the working color space
for Nikon Capture 4. To choose a default
RGB color-space profile for the working
color space in Nikon Capture 4, choose (B)
Always use the default RGB color space
set below as the working color space for
Nikon Capture 4. Click OK to put changes
into effect and proceed to the next step.
When (B) Always use the default RGB color space set below as the working color
space for Nikon Capture 4 is selected, the ColorSync settings button will be active. Click
this button to display the ColorSync dialog. After opening the Default Profiles tab (Mac
OS X) or opening the Profiles tab and selecting Default Profiles for Documents (Mac OS 9),
choose the default working RGB color space from the RGB Default menu.
Mac OS X
Mac OS 9
75
Macintosh
Clicking Color space details displays a description of the different color-space profiles. Use
this explanation to help you choose a color-space profile.
The default output color-space profile can be changed at any time after installation in the
Color Management tab of the Nikon Capture 4 Editor or Nikon Capture 4 Camera Control
Preferences dialog.
2.1.9 — Complete installation of Nikon Capture 4
The following dialog is displayed when installation of Nikon Capture 4 is complete. Click
Quit to proceed to the next step.
Add to Dock (Mac OS X)
The dialog shown at right will be displayed when Nikon Capture 4
Editor and Nikon Capture 4 Camera Control are installed. Click Yes
to add these components to the Dock, or No to exit without adding
these components to the Dock.
76
Installing Nikon Capture 4 on a Macintosh
2.2 — Restart the computer
Click Restart to restart the computer.
77
Macintosh
Connecting to a Computer
Before connecting your camera to a Macintosh computer for the first time, make sure that
you install Nikon Capture 4. After installing Nikon Capture 4, turn the camera on and connect it to the computer, or insert the memory card into a card reader or a PC card slot.
For more information about connecting your camera to a computer, see the documentation
provided with your camera.
D1-Series ( Firewire Interface)
D2-Series /D100/D70s/D70/D50 (USB Interface)
Use a Reliable Power Source
To ensure that data transfer is not interrupted, be sure that the battery is fully charged. If in doubt,
charge the battery before use or use an AC adapter (available separately). If the battery is exhausted
during transfer, transfer will be interrupted and data may be lost.
78
Connecting to a Computer
Using a PC Card Slot
When inserted in a PC-card adapter (available separately), the camera memory card functions
as a Type II PCMCIA ATA card, allowing images to be read from the card.
Inserting a Memory Card
Remove the memory card from the camera and insert it in the adapter.
Insert the adapter into a PCMCIA TYPE II ATA card slot on your computer. For more information on inserting the adapter, see the documentation provided with your computer.
TM
lash
pactF
Com
AD1
Card EC-
AD
AP
TER
lash
pactF
Com
TM
Card
F
64C
EC-
Depending on your computer’s operating environment, you may need to install software,
register the card adapter, or adjust OS settings when the adapter is inserted into the card slot.
For more information, refer to the instruction manual for your operating system.
Using a Card Reader
Images on the memory card can also be viewed using a card reader.
Inserting a Memory Card
After removing the memory card from the camera, insert it in the card reader and connect
the reader to the computer. See the documentation provided with the card reader for more
information on connecting it to a computer.
Card reader (USB interface)
Card reader
Memory card
79
Macintosh
Uninstall
Uninstalling Nikon Capture 4
This section describes how to uninstall the Macintosh versions of Nikon Capture 4.
Uninstalling Nikon Capture 4
1
2
Insert the Nikon Capture 4 CD into a CD-ROM drive and start the Nikon Capture 4 installer as described on pages 72–73 of “Installing Nikon Capture 4 on a Macintosh.”
3
4
Click the Uninstall button at the bottom right corner of the Nikon Capture Installer dialog.
80
Select Uninstall from the menu at the top left corner of the Nikon Capture Installer dialog.
Once Nikon Capture 4 has been removed from your system, the dialog shown below will
be displayed. Click OK.
En
No reproduction in any form of this manual, in whole or in part (except for
brief quotation in critical articles or reviews), may be made without written
authorization from NIKON CORPORATION.
Ver. 4.3 Install Guide
Ver. 4.3
En
Printed in Japan
SB5E00500101(11)
6MSA9711--
Install Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement