ICS RD1G Residual current device Scheda dati
PDF
Scarica
Documento
Pubblicità
Pubblicità
Relè differenziale 96x96mm Versione salvavita,con blocco elettrico (t = 0) a I Δ n 30mA Punto di intervento selezionabile 30mA…30A (19 portate) Visualizzazione istantanea percentuale di I Δ n Sicurezza positiva o negativa selezionabile in campo Test automatico permanente Relè di allarme + preallarme oppure relè allarme con doppio scambio Residual current device 96x96mm Delta 96-S Instantaneous (t = 0) at I Δ n 30mA Selectable set point 30mA…30A (19 ranges) Instantaneous display as percentage of I Δ n Field-selectable negative or positive security (fail safe) Automatic permanent test Alarm relay + pre-alarm or alarm relay with double exchange Pulsante di ripristino Reset key Segnalazione intervenuto allarme (LED rosso) Red LED for an occured alarm Indicazione istantanea della corrente differenziale Instantaneous display of earth leakage current ~ Pulsante Test Test key Selettore stato relè uscita: ND Ne Selettore portata x1 / x10 / x100 Range selector x1 / x10 / x100 (norm. diseccitato) sicurezza negativa (norm. eccitato) sicurezza positiva Switch for state output relay: ND Ne Selezione punto di intervento I Δn (norm. de-energised) negative security (norm. energised) positive security Selezione tempo di intervento Setting intervention time Setting intervention threshold I Δn (t=0) Selettore: Al.2 allarme con 2 contatti SPDT Al.50% allarme + preallarme 50% I Δn Selector: Al.2 alarm with 2 SPDT contacts Al.50% alarm + 50% I Δn pre-alarm Segnalazione apparecchio alimentato (LED verde) Green LED for fed meter ICS Schneider Messtechnik GmbH Briesestraße 59 D-16562 Hohen Neuendorf / OT Bergfelde Tel.: 03303 / 504066 Fax: 03303 / 504068 [email protected] www.ics-schneider.de 96-S MODELLO MODEL CODICE CODE RD1G2... NOTA TECNICA TECHNICAL NOTE PORTATE RANGES BLOCCO ELETTRICO ISTANTANEOUS FORMA D’ONDA WAVEFORM FILTRO COMPONENTI ARMONICHE FILTER FOR HARMONICS NORMA DI RIFERIMENTO ACCORDING TO 19: 0,03...30A NT691 ✘ 18: 0,5...30A t=0s a/at I Δn 30mA ✘ Sinusoidale (tipo AC) Sinusoidal (AC type) ✘ Pulsante parzializzata con componente continua (tipo A) Chopped pulsating with superimposed dc (A type) ✘ Selezionabile Selectable Fisso Fixed EN60947-2 IEC60947-2 ✘ 1 Uscita Relè 1 Relay Output ALLARME ALARM 2 Uscite Relè 2 Relays Output ❖ 1 Uscita + Preallarme 1 Output + Pre-alarm ❖ IΔn Barra LED LED Bargraph ✘ DISPLAY Display VISUALIZZAZIONE SPDT USCITA RELE’ RELAY OUTPUT SICUREZZA positiva / negativa SECURITY positive / negative TEST RIPRISTINO RESET SPDT + SPST 2 SPDT ✘ Selezionabile Selectable ✘ Locale Local ✘ ■ Remoto Remote Automatico Automatic ✘ Locale Local ✘ ✘ Remoto Remote Automatico Automatic 230Vca/ac ALIMENTAZIONE AUSILIARIA AUXILIARY SUPPLY 24-48-115-240-400Vca/ac 20...150Vcc/dc ✘ ✘ ✘ 10...36Vcc/dc 2 Moduli 2 Module 4 Moduli 4 Module DIMENSIONI DIMENSIONS 48 x 48 mm 72 x 72 mm 96 x 96 mm ❖ In alternativa On choice ICS Schneider Messtechnik GmbH Briesestraße 59 D-16562 Hohen Neuendorf / OT Bergfelde ✘ ■ Non realizzabile con al.aus.20...150Vcc-48Vca Not available with aux. supply 20...150Vdc-48Vac Tel.: 03303 / 504066 Fax: 03303 / 504068 [email protected] www.ics-schneider.de CODICI DI ORDINAZIONE ORDERING CODE AL. AUSILIARIA AUX. SUPPLY RD1G211B 24V ca/ac RD1G212B 115V ca/ac RD1G213B 230V ca/ac RD1G214B 240V ca/ac RD1G215B 4400V ca/acR RD1G21HB 20...150Vcc/dc + 48V ca/ac INGRESSO INPUT Inserzione: linea bassa tensione, con trasformatore serie TD Connection: low voltage lines, with series TD transformer Forma d’onda IΔn: sinusoidale (tipo AC) o pulsante parzializzata con componente Waveform I∆n: sinusoidal (type AC) or chopped pulsating with superimposed d.c. continua (tipo A) in accordo con EN60947-2 (annesso B e M) ed. VIII (2007) / IEC60947-2 (type A) according to EN60947-2 (annex B and M) IEC60947-2 Frequenza nominale fn: 50Hz Rated frequency fn: 50Hz Frequenza di funzionamento: 47...63Hz Working frequency: 47...63Hz PREDISPOSIZIONE SET UP Punto di intervento IΔn: selezionabile con potenziometro a 7 posizioni, 3 gamme Current set point I Δn: selectable by 7-position potentiometer, 3 ranges x1 - x10 - x100 x1 - x10 - x100 Portate IΔn: vedi tabella Ranges I Δn: see table 0,03 0,05 0,075 0,1 0,15 0,2 0,3 X1 30mA 50mA 75mA 100mA 150mA 200mA 300mA X10 300mA 500mA 750mA 1A 1,5A 2A 3A X100 3A 5A 7,5A 10A 15A 20A 30A IΔn Corrente differenziale di non intervento: 0,5 IΔn Non-operating residual current : 0,5IΔn Tempo di intervento t: selezionabile con potenziometro a 7 posizioni Intervention time t: selectable by 7 position potentiometer Campo regolazione t: 0 - 0,15 - 0,25 - 0,5 - 1 - 2,5 - 5 secondi Adjustable range t: 0 - 0,15 - 0,25 - 0,5 - 1 - 2,5 - 5 seconds Soglia intervento (IΔn) Set point (I Δn) 0,03A Ritardo impostato t(s) Selected delay t(s) 0s Tempo non intervento @ 2IΔn Non-operating time at @ 2I Δn Max. ritardo @ 5IΔn Max. delay @ 5I Δn 0,03s 0,05...30A 0,15s 0,25s 0,5s 1s 2,5s 5s 0,15s 0,25s 0,5s 1s 2,5s 5s 0,24s 0,35s 0,63s 1,20s 2,80s 5,50s Selezionando la soglia di intervento nella posizione 0,03 viene automaticamente Selecting the intervention threshold on position 0,03 the intervention delay is escluso il ritardo intervento, indipendentemente dalla posizione del moltiplicatoreautomatically di excluded, independently of position of range selector portata (x1/10/100). (x1/10/100). Selettore Al.2 - Al.50% Switch Al.2 - Al.50% Al.2: relè di allarme con doppio scambio Al.2: alarm relay with double exchange Al.50%: relè di allarme + preallarme 50% I∆n Al.50%: alarm relay + pre-alarm 50% I∆n Il relè contrassegnato 60 - 61 - 62 è un preallarme con soglia intervento fissa, pari a Relay marked 60 - 61 - 62 is a pre-alarm state with fixed intervention threshold, 50% del valore di I∆n selezionato equal 50% of selected I∆n value SEGNALAZIONE SIGNALING Strumento alimentato: LED verde "ON" Power ON: green LED "ON" Valore istantaneo IΔn: 4 LED gialli, 20 - 30 - 40 - 50% del valore Δn I impostato Instantaneous value I Δn: 4 yellow LED's, 20 - 30 - 40 - 50% of set IΔn value Intervento allarme: LED rosso "TRIP" + commutazione relè “TRIP” Alarm intervention: red LED "TRIP" + “TRIP” relay switching Interruzione collegamenti relè - toroide: lampeggio LED rosso "TRIP" + Ring current transformer-relay connection failure: red LED "TRIP" blinking + commutazione relè “TRIP” “TRIP” relay switching Preallarme: commutazione relé 50% I∆n Pre-alarm: 50% I∆n relay switching CONTROLLO CONTROL Test manuale: verifica l'efficienza del relè differenziale Manual test: it verifies the residual current relay perfect working Locale: pulsante frontale Local: front key Remoto: chiusura contatto esterno (Non realizzabile con aux cc e con Uaux 48Vca) Remote: by external contact closing (Not available with dc supply and Uaux 48Vac) Test automatico permanente: verifica la continuità del collegamento relè Automatic continuous test: it verifies the integrity of the connection between differenziale - toroide relay and ring core ALLARME ALARM Memorizzazione intervento: LED rosso "TRIP" + autoritenuta relè TRIP state memorization: red LED "TRIP" + relay self-retaining Ripristino (reset): manuale Reset: manual Manuale locale: pulsante frontale Local manual: front key Manuale remoto: chiusura contatto esterno Remote manual: external contact closing Ripristino inibito con corrente differenziale persistente: > 50% IΔn Inhibited reset with persistent residual current: > 50% I Δn USCITA OUTPUT Allarme con doppio scambio (Al.2) Alarm relay with double exchange (Al.2) Relè “TRIP”: 2 contatti di scambio SPDT “TRIP” relay: 2 SPDT contacts Allarme + preallarme (Al.50%) Alarm + pre-alarm (Al.50%) Relè “TRIP”: 1 contatto di scambio SPDT “TRIP” relay: 1 SPDT contact Relè 50% I∆n: 1 contatto di scambio SPDT (sicurezza negativa) 50% I∆n relay: 1 SPDT contact (negative security) Sicurezza negativa/condizionata (relè normalmente diseccitato) oppure Negative security (normally de-energised relay) or positive security fail safe positiva/incondizionata (relè normalmente eccitato): selezionabile tramite dip switch(normally energised relay): selectable by dip switch AUXILIARY SUPPLY Valore nominale Uaux: 48 - 115V - 230V - 240V - 400V Rated value Uaux: 48 - 115V - 230V - 240V - 400V Variazione ammessa: 0,85...1,1Uaux - 40...60V (Uaux 48V) Tolerance: 0,85...1,1Uaux - 40...60V (Uaux 48V) Frequenza nominale: 50Hz Rated frequency: 50Hz Variazione ammessa: 47...63Hz Tolerance: 47…63Hz Autoconsumo: ≤ 2,5VA Rated burden: ≤ 2,5VA Valore nominale Uaux: 20...150Vcc Rated value Uaux: 20...150Vdc Protezione contro l’inversione di polarità Protected against incorrect polarity Autoconsumo: ≤ 2,5W Rated burden: ≤ 2,5W Insensibilità ai buchi di tensione con durata fino a 150ms (Uaux nominale) Immunity to short interruption of supply voltage up to 150ms (Rated Uaux) ISOLAMENTO INSULATION (EN/IEC 60947-1) Categoria di installazione: III Installation category: III Grado di inquinamento: 2 Pollution degree: 2 Tensione di riferimento per l’isolamento: 450V Insulation reference voltage: 450V Prova di tensione a impulso 5kV 1,2/50µs 0,5J Impulse voltage test 5kV 1,2/50 μs 0,5J (EN/IEC 60947-1) Circuiti considerati: ingresso, uscita relè, alimentazione ausiliaria Considered circuits: input, relay output, auxiliary supply Prova a tensione alternata 2,5kV valore efficace 50Hz/1min A.C. voltage test 2,5kV r.m.s. 50Hz/1 min Circuiti considerati: ingresso, uscita relè, alimentazione ausiliaria Considered circuits: input, relay output, auxiliary supply Prova a tensione alternata 4kV valore efficace 50Hz/1min A.C. voltage test 4kV r.m.s. 50Hz/1 min Circuiti considerati: tutti i circuiti e massa Considered circuits: all circuits and earth PROVE DI COMPATIBILITA’ ELETTROMAGNETICA TESTS FOR ELECTROMAGNETIC COMPATIBILITY Prove di emissione in accordo con EN / IEC 60947-2 Emission tests according to EN / IEC 60947-2 Prove di immunità in accordo con EN / IEC 60947-2 Immunity tests according to EN / IEC 60947-2 CONDIZIONI AMBIENTALI ENVIRONMENTAL CONDITIONS Temperatura di impiego: -5…50°C Nominal temperature range: -5…50°C Temperatura limite di funzionamento: -10…55°C Limit temperature range: -10…55°C Temperatura di magazzinaggio: -40…70°C Limit temperature range for storage: -40…70°C Umidità relativa (IEC60755): 50% (valore massimo a 40°C) Relative humidity (IEC60755): 50% (highest value at 40°C) Adatto all’utilizzo in clima tropicale Suitable for tropical climates Massima potenza dissipata1: ≤ 2W Max. power dissipation1 : ≤ 2W 1 Per il dimensionamento termico dei quadri 1 For switchboard thermal calculation CUSTODIA HOUSING Custodia: incasso (foratura pannello 92x92mm) Housing: flush mounting (panel cutout 72x72mm) Frontale: 96x96mm Front frame: 96x96mm Profondità: 80mm Depth: 80 mm Connessioni: faston 6,3x0,8mm Connections: fast-ons 6,3x0,8mm Materiale custodia: policarbonato autoestinguente Housing material: self-extinguishing policarbonate Grado di protezione (EN/IEC 60529): IP40 (frontale), IP20 (morsetti) Protection degree (EN/IEC 60529): IP40 front frame, IP20 terminals Peso: 280 grammi Weight: 280 grams NT691 06 - 2010 3a Ed. pag.4/5 ALIMENTAZIONE AUSILIARIA S 291/86 S 291/123 TRIP RESET TEST INPUT 19 18 17 60 61 62 4 6 1 3 2 Al.2 B AUX. SUPPLY (+) (—) TRIP Al.50% 20 21 19 18 17 60 61 62 4 6 TRANSFORMER INPUT TEST 1 3 2 Al.50% A B AUX. SUPPLY (+) (—) 20 21 A L1 L2 L3 N L1 L2 L3 N ICS Schneider Messtechnik GmbH Briesestraße 59 D-16562 Hohen Neuendorf / OT Bergfelde RESET Tel.: 03303 / 504066 Fax: 03303 / 504068 [email protected] www.ics-schneider.de ">

Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato.
Pubblicità