ENG CD3000M 3PH up to 90A

ENG CD3000M 3PH up to 90A
USER’S MANUAL
Rev. 12/2004
CD3000M-3PH
THYRISTOR UNIT
Up To
CD Automation S.r.l.
Via Picasso 34/36 - 20025 – Legnano (MI) – ITALY
Tel +39 0331 577479 – Fax +39 0331 579479
E-Mail: [email protected] - WEB: www.cdautomation.com
90A
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
CD3000M-3PH Thyristor Unit up to 90A
Index:
1.
1.1
1.2
1.3
1.4
2.
2.1
2.2
2.3
2.4
Glossary
5
Terminology
Input signal
Power feed back
What is a thyristor unit
5
5
5
5
Technical specifications
6
General Features:
Input features
Output features
Derating curve
6
6
7
7
3.
Ordering information
8
4.
Installation and wiring information
9
4.1
4.2
4.3
4.4
4.5
5.
5.2
5.3
5.4
6.
6.1
6.2
6.3
6.4
7.
7.1
7.2
7.3
8.
8.1
8.2
9.
9.1
9.2
Identification of the unit
Installation
Dimensions
CT dimensions (Heater Break HB)
Fixing Holes
9
9
10
10
11
Wiring Instructions
12
Cabling detail
Wiring connections
LED Status Table
14
16
19
START UP
20
To remove the board
Auxiliary supply
Analog input
Heater Break Alarm
21
22
23
25
Thyristor firing mode
30
Zero Crossing (ZC)
Burst Firing (BF)
Configurator
30
30
31
Fuse and fuseholder for UL certification unit
Fuse and Fuse Code
FuseHolder size
33
33
34
Fuse and fuseholder for CE mark unit
35
Fuse and Fuse Code
FuseHolder size
35
36
1
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
10. Modbus communication
37
10.1
10.2
10.3
10.4
10.5
37
37
42
47
51
Physical requirements
ModBus RTU protocol
Word parameters
Thyristor unit Configuration
Address configuration
11. Maintenance
54
11.1
11.2
11.3
11.4
11.5
54
55
55
55
55
Trouble Shooting
Repairing procedure
Fans
Servicing
Warranty conditions
12. CD Automation’s distributors
www.cdautomation.com
56
2
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
CAUTION
Thyristor units are used in power industrial equipment. When the thyristor unit is working, there are
on the unit the following voltages
- Maximum main supply voltage on power terminals up to 600V.
- Auxiliary supply 230-460Vac.
- Fan voltage 230Vac 50/60Hz Power consumption 14W.
Don't remove the plastic cover which provides adequate protection against electric shock.
Don’t use this thyristor in aerospace and nuclear application.
Electric Shock Hazard (Risque the choque électrique)
When thyristor unit has been connected to main supply voltage and is switched off, before to touch
it be secure that the unit is isolated and wait at least one minute to permit to discharge internal
capacitors. Thus be secure that:
• access to thyristor unit is only permitted to specialized personnel;
• the authorised personnel must read this manual before to have access to the unit;
• the access to the units must be denied to unauthorized personnel.
Important warnings(attention)
• Local regulations regarding electrical installation should be rigidly observed.
• Safety regulations must be rigidly observed.
• Don't bend components to maintain insulation distances.
• Protect the units from high temperature, humidity and vibrations.
• Don't touch components to prevent elettrostatichal discharges on them.
• Verify that all ratings are in line with real needs.
• If authorized personnel must measure voltage, current etc. on units, take away rings and other
jewels from fingers and hands.
• Authorized personnel working on thyristor unit under power supply voltage must work on insulated
board. Be secure that board is not connected to earth.
This listing does not represent a complete enumeration of all necessary safety cautions.
3
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
Protection(protection)
CD3000 thyristor family has a polymeric plastic cover in compliance to International specification
IP20. To understand if IP20 protection is sufficient should be evaluated the installation place where
the units are installed.
Open Type Equipment(équipment de type ouvert).
Maximum surrounding air temperature 40°C(Temperature de l’air environnante maximum 40°C).
Earth(terre)
CD3000 family has isolated heatsink. For safety connect the heatsink to earth to avoid shocks in
case that circuit board or thyristors lost insulation. Earth impedance should be correspondent to
local earth regulation. Periodically the earth efficiency should be inspected.
Electronic Supply(alimentation électronique)
CD3000 family electronic circuit should be supplied by dedicated voltage supply for all electronic
circuit but not in parallel with contactor's coil, solenoids and other inductive or capacitive loads. It's
recommended to use a shielded transformer.
Electromagnetic compatibility (compatibilité électromagnétique)
Our thyristor unit has an excellent immunity to electromagnetic interferences if all suggestions
contained in this manual are respected. In respect to a good Engineering practise, all inductive
loads like solenoids contactor coils should have a filter in parallel.
Emissions (emission)
All thyristor switching at high speed generate some radiofrequency disturbance. CD3000 serie
complies with EMC rules for CE mark. In many installations near electronic devices has not been
noted problems. If radiofrequency device at low frequency are used near the thyristor unit, some
precautions should be taken like line filters and shielded cables for input signal and for load cables.
C
UL
®
US
LISTED
NOTE
We reserves the right to apply modifications to the our products without any advice.
www.cdautomation.com
4
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
1. Glossary
1.1 Terminology
V:
I:
P:
voltage power supply.
the full circulating current in thyristor unit.
total load power.
1.2 Input signal
SSR:
AN:
IRS:
This input type is a square waveform generated by a temperature controller.
Analog input.
Communication command.
1.3 Power feed back
Feedback:
supply voltage fluctuation changes the power to the load. To overcome this effect
the voltage supplied to the load is measured and compared with power demand from
controller, the error signal is used to automatically hold the power at demanded level.
1.4 What is a thyristor unit
A thyristor unit is semiconductor device which acts as a switch formed by two thyristors in
antiparallel. To switch on the alternating current the input signal will be on and the thyristor will
switch off at first zero crossing voltage with no input signal. The benefits of thyristor units
compared with elettromechanical contactors are numerouses: no mooving parts, no maintenance
and capacity to switch very fast. Thyristors are the only solution to control transformers and
special loads that change resistance with temperature and with age.
LOAD
5
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
2. Technical specifications
2.1 General Features:
Operating temperature
0÷40°C for higher temperature see derating curve
Voltage power supply
24V minimum, 480V max and 600V on request
Input signal
SSR
4÷20 mA
0÷10V
potentiometer (10k ohm)
customer configurable with automatic zero/span calibration
Firing mode
One of these firing modes can be configured on line via serial port
Zero Crossing (ZC)
Burst Firing (BF)
Auxiliary voltage supply
230V range (230 ±15%) 10VA
460V range (380 –15%) ÷ (460 +15%); 10VA
(sincronized with supply Voltage)
Fan voltage supply
230V range (230 ±15%) 10VA
460V range (380 –15%) ÷ (460 +15%); 10VA
(sincronized with supply Voltage)
Heather break alarm
Discrimination better than 20%. Circuit microprocessor based to
diagnose partial or total load failure and short circuit on Thyristors.
Latching alarm plus reset. Relay output 0,5A at 125V
Line Drop Voltage
Automatic compensation ±15% of supply voltage with analog input
Mounting
Bulk head mounting
Protection
IP20
2.2 Input features
Input signal
SSR
Maximum current
drain
Input
Impedance
5mA constant current
Analog 0÷10V
-
8200 ohm
Analog 4÷20mA
-
100 ohm
Potentiometer
10K ohm
www.cdautomation.com
8200 ohm
6
ON condition
OFF condition
≥4V - max 30V
≤1V
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
2.3 Output features
NA=not Available
Current
Voltage
range
Ripetitive peak
reverse voltage
Latching
current
Max peak
one cycle
Leakage
current
I2T value
thyristor
Frequency Power loss
range
Isolation
Voltage
(A)
(V)
(480V)
(600V)
(mAeff)
(10msec.) (A)
(mAeff)
tp=10msec
(Hz)
I=Inom
(W )
Vac
15
24÷480
1200
1200
150
230
15
610
47÷70
54
2500
30
24÷600
1200
1600
250
600
15
1800
47÷70
108
2500
45
24÷600
1200
1600
250
600
15
1800
47÷70
162
2500
60
24÷600
1200
1600
250
1000
15
4750
47÷70
216
2500
75
24÷600
1200
1600
450
1540
15
11300
4 7 ÷7 0
270
2500
90
24÷600
1200
1600
450
2000
15
19100
47÷70
324
2500
2.4 Derating curve
K
I
MAX
=I
NOM
xK
1
0.8
0.6
0.4
0.2
0
40
50
60
7
70
80
°C
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
3. Ordering information
Model CD3000M 3PH
1
CD3000M-3PH
Ex:CD3000M 3PH/
75A/
2
400V
/
3
480V
/
4
460V
/
5
SSR/
6
ZC/
7
UL
1 Nominal current of CD3000M
15A
60A
30A
75A
45A
90A
2 Operating Load Voltage (incoming voltage supply)
Specify the value of the line supply.
3 Max VOLTAGE of CD3000M
480V
600V
The voltage on the identification label must be equal or more than
operating voltage. The minimum voltage supply to the load is 24V.
4 Auxiliary Voltage
230V
200÷230V ±15%; 10VA
460V
300÷460V ±15%; 10VA
600V
600V ±15%; 10VA (on request)
5 Input
SSR
0-10V
4-20mA
10K pot
4÷30VDC
0÷10V analog input
4÷20mA analog input
Potentiometer
6 Firing
ZC
Zero Crossing
BF
Burst firing. Specify the number on ON cycles at 50% of
power.
7 Options
COMM
MODBUS protocol in RS485 is standard
EF
External fuses and fuseholders
NF
No fuses
CD-KP
External Keypad
HB
Heater Break Alarm
FAN110 Fan voltage supply 110VAC ± 15% (std 230VAC ± 15%)
14W 50/60Hz
UL
UL Certification
www.cdautomation.com
8
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
4. Installation and wiring information
4.1 Identification of the unit
Before to install the CD3000M unit examine for damages or deficiencies. If any is found,
notify the carrier immediately. Check that the product features shown on CD3000M
cover and identification label corresponds to that ordered.
An identification label provides all the
informations regarding the factory
settings of the unit. This label is on the
board inside the unit, as represented
AMPS
AUX.
240V
15 60
25 90
440V
____
35 110
45 ___
INPUT
FIRING OPT.
ZC
S.S
0-10V
SC
DT
4-20mA
SSR
____
POT
PA
4.2 Installation
CD3000M unit should be always
mounted in vertical position to
improve air cooling on heatsink.
Maintain minimum distances in
vertical
and
in
horizontal
as
below
represented. Don’t install in proximity of hot
elements
and
near
units
generating
electromagnetic interferences.
When more units are mounted inside a cubicle
provide air circulation as below represented.
Sometimes it is necessary to provide a fan to
have a better air circulation.
AIR OUTPUT
2 cm
15cm
AIR INPUT
9
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
4.3 Dimensions
CD3000M 3PH
15 (S2C)
CD3000M 3PH
30A (S4C)
CD3000M 3PH
45A (S6C)
D
H
H
H
W
D
H
D
W
W
D
W
Size
W(mm)
H(mm)
D(mm)
15A (S2C)
123
120
120
30A (S4C)
148
120
123
45A (S6C)
148
138
123
60A (S8C)
148
138
159
75A (S8C)
148
138
159
90A (S8C)
148
138
159
4.4 CT dimensions (Heater Break HB)
12
8
39
CD3000M 3PH
60-75-90A (S8C)
39
www.cdautomation.com
20
10
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
4.5 Fixing Holes
B
C
E
D
A
Size
15A (S2C)
30A (S4C)
A(mm)
110
-
B(mm)
C(mm)
D(mm)
E(mm)
30
30
-
-
-
-
110
65
45A (S6C)
-
-
-
110
65
60A (S8C)
-
-
-
110
65
75A (S8C)
-
-
-
110
65
90A (S8C)
-
-
-
110
65
11
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
5. Wiring Instructions
Warning: this procedure can be done just by specialized personnel.
CD3000M unit has isolated heatsink. For safety connect the heatsink to hearth using its terminal
with hearth symbol.
CD3000M can be susceptible to airborne interferences from near equipment or from interferences on
main supply, so a number of precautions must be taken.
• Contactors coils and chokes must have in parallel a RC filter and must be supplied with a different
voltage line.
• All input/output signal must use screened bifilar wires.
• Signal input and output must not routing in same cable try and must not be parallel.
• Local regulations regarding electrical installation should be rigidly observed.
3.3.2 Auxiliary terminals
Before connect or disconnect, make sure that the power, control cables and wires are
insulated from the voltage
Terminal
Description
1
-
External Calibration command 24 Vdc max
2
+
External Calibration command 24 Vdc max
3
Reset
4
Reset
5
+
Output Command signal to CD3000 (Internal Connections)
6
-
Output Command signal to CD3000 (Internal Connections)
A2+
+
Input command signal 4÷20mA,0÷10V,SSR
A1-
-
Input command signal 4÷20mA,0÷10V,SSR
7
RS485 A
8
RS485 B
9
Output +8Vdc stabilized 1 mA MAX
10
Common relay H.B. alarm
11
NC/NO H.B. relay alarm
12
Option
13
CT input with H.B. option
14
CT input with H.B. option
15
Nc not connected
16
Auxiliary supply voltage 230-460Vac
17
Ground
18
Auxiliary supply voltage 230-460Vac
www.cdautomation.com
12
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
5.1.1 Power Terminals
Before connect or disconnect, make sure that the power, control cables and wires are
insulated from the voltage
Terminal
Description
L1
Line Input
T1
Load Output
L2
Line Input
T2
Load Output
L3
Line Input
T3
Load Output
13
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
5.2 Cabling detail
Use 75°C copper (CU) conductor only, provided with the terminal type indicated below.
(Utiliser conducteur de cuivre (CU) pour 75°C seulement, avec les terminal suivants )
Current/courant
Torque/couple
Lb-in (N-m)
Wire/cable
15A
26.6 (3.0)
18-8
30A, 45A
60A, 75A, 90A
70.8 (8.0)
18-1
www.cdautomation.com
14
Wire terminal/terminal
UL Listed (ZMVV)
Wire Pin Terminal
(terminal avec cosse)
UL Listed (ZMVV)
- Fork/Spade Terminal
(terminal avec cosse a
fourche)
- Copper Tube Cr. Lug
(cosse tubulaire a plage
étroite)
User’s Manual
CD3000M-3PH up to 90A
Power terminals: wire details:
Current
C.D. Automation Srl
Supply
Cable
Load
Screw
Clable
Screw
mm2
AWG
M
mm2
AWG
M
15A
4
12
M5
4
12
M5
30A
6
10
M6
6
10
M6
45A
10
8
M6
10
8
M6
60A
16
6
M6
16
6
M6
75A
25
4
M6
25
4
M6
90A
35
3
M6
35
3
M6
Auxiliary connectors and earth:
Current
Auxiliary Supply
Earth
Cable
Clable
Screw
mm2
AWG
mm2
AWG
M
15A
0,50
18
4
12
M4
30A
0,50
18
6
10
M5
45A
0,50
18
6
10
M5
60A
0,50
18
6
10
M5
75A
0,50
18
6
10
M5
90A
0,50
18
6
10
M5
15
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
5.3 Wiring connections
5.3.1 CD3000 15-25-35-45A
L1
L1
L2
L3
L2
Externa l
Calibration
L3
Reset
- +
L3
1
POWER UNIT
POWER UNIT
L2
POWER UNIT
L1
2
3
* The user installation must
be protect by
electromagnetic circuit
breaker or by fuse isolator
4
7
RS485-A
8
RS485-B
10V
9
10
COM
11
NO/NC
**
H.B.
Contact
12
13
CT
14
15
16
17
** If the Auxiliary Voltage
(written on the identification
label) is different from Supply
Voltage (to the load), use an
external transformer as
designated above.
18
T1
T2
CT1
5
T3
CT2
6 A2+ A1-
CT3
+ - Input
Open Delta Load
Delta Load
Neutral
Start Load + Neutral
NOTE: IMPORTANT
To work, terminals 3-4 must be linked.
The auxiliary voltage supply of Drive M unit
must be connected as above, and must be
syncronized with load voltage power supply (L2,
L3).
Start Load
www.cdautomation.com
16
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
5.3.2 CD3000 30A
L1
L1
L2
L3
L2
External
Cali bration
L3
Reset
* The user installation must
be protect by
electromagnetic circuit
breaker or by fuse isolator
- +
L1
L2
L3
1
2
3 4
7
POWER UNIT
8
9
RS485-A
RS485-B
8V
10
COM
11
NO/NC
**
H.B.
Contact
12
13
CT
14
15
16
17
18
T1
T2
CT3
5
T3
CT1
** If the Auxiliary Voltage
(written on the identification
label) is different from Supply
Voltage (to the load), use an
external transformer as
designated above.
6 A2+ A1-
CT2
+ - Input
Open Delta Load
Delta Load
Neutral
Start Load + Neutral
NOTE: IMPORTANT
To work, terminals 3-4 must be linked.
The auxiliary voltage supply of Drive M unit
must be connected as above, and must be
syncronized with load voltage power supply (L2,
L3).
Start Load
17
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
5.3.3 CD3000 45-60-75-90A
L1
L1
L2
L3
L2
220 Vac
FAN
External
Calibrati on
L3
Reset
* The user installation must
be protect by
electromagnetic circuit
breaker or by fuse isolator
- +
L1
L2
L3
1
2
3 4
POWER UNIT
7
8
9
RS485-A
RS485-B
8V
10
COM
11
12
NO/NC
13
**
H.B.
Contact
CT
14
15
16
17
18
T1
T2
CT3
5 6 A2+ A1-
T3
CT1
** If the Auxiliary Voltage
(written on the identification
label) is different from Supply
Voltage (to the load), use an
external transformer as
designated above.
CT2
+ - Input
Open Delta Load
Delta Load
Neutral
Start Load + Neutral
NOTE: IMPORTANT
To work, terminals 3-4 must be linked.
The auxiliary voltage supply of Drive M unit
must be connected as above, and must be
syncronized with load voltage power supply (L2,
L3).
Start Load
www.cdautomation.com
18
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
5.4 LED Status Table
LED
STATUS
DESCRIPTION
PW
Auxiliary supply is not connect
Auxiliary supply is connect
SC
SCR OK
SCR short circuit
HB
Laod OK
Load Fault
ON
OFF Condition(Load IS NOT Powered)
ON Condition(Load IS Powered)
= OFF
= ON
19
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
6. START UP
Before to supply the thyristor unit:
• verify that load current equal or less than nominal;
For resistive load
I=
•
•
•
•
For inductive delta open load
P
V 3
Tot
I=
P
3V
Tot
verify that there is no short circuit on load;
verify that main voltage equal or less than nominal;
verify that all auxiliary connections are right and syncronized to main voltage!!!;
Fan voltage equal than nominal (230V std, 120V optional)
After which supply thyristor unit giving the maximum input signal and verify that load current is
equal or less than thyristor unit nominal current.
Warning: this procedure can be done just by specialized personnel.
The thyristor unit is delivered configured and tuned in line with customer
requirements. If it’s necessary to change on site the configuration, procede as below
specified.
www.cdautomation.com
20
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
6.1 To remove the board
1 Remove plastic Cover
2 Pull the PCB
21
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
6.2 Auxiliary supply
Warning: this procedure can be done just by specialized personnel.
To change auxiliary supply voltage sold the correct link-jumper on main PCB
Main PCB
230V Auxiliary supply
J9
J10
J11
460V Auxiliary supply
J9
J9
J10
J10
J11
J11
•
•
If the Auxiliary Voltage (written on the identification label) is different from Supply Voltage
(to the load ), use an external transformer.
If load voltage is not included in range of 230V ±15% or 460V +15% provide an external
transformer with primary equal to load voltage and secondary 230V if your unit is setted to
230V.
www.cdautomation.com
22
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
6.3 Analog input
Warning: this procedure can be done just by specialized personnel.
6.3.1 Setting Analog input
To change input type remove plastic cover and configure jumpers as represented below:
Jumpers Configuration
FRONT PCB
Input
SSR
0÷10V
4÷20MA
J7
J16
J17
AB C
CB A
CB A
AB C
CB A
CB A
AB C
CB A
CB A
Front PCB
23
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
6.3.2 Tuning Analog input
Warning: this procedure can be done just by specialized personnel.
START TUNE
UNIT OFF
Mantain Kay CAL pushed
and Switch ON
2sec.
Release key
when red and yellow
led are ON
Yello and red leds
are flashing
SSR
INPUT TYPE
ON
S/C
H.B.
ON
S/C
H.B.
ANALOG
Wait for more than 10 sec.
from start flashing
yellow and red leds
Within 10 sec. from start
flashing yellow and red leds
push again momentary
CAL Key
The leds will
stop flashing
Yellow led only is
flashing, apply
0 input Signal
I.E.: 0V for 0-10V
4mA for 4-20mA
ON
S/C
H.B.
SSR input (3-30V)
is tuned
ON
S/C
H.B
0 Signal
Now press CAL Key again
Red led only is
flashing, apply
10V for 0-10V input
or
20mA for 4-20mA input
Now press CAL Key again
Analog input
is tuned
END
TUNE
www.cdautomation.com
24
ON
S/C
H.B
Max Signal
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
6.4 Heater Break Alarm
Heater Break Alarm is a microprocessor based circuit to diagnose partial or total load failure and
short circuit on SCR and fuses failure.
•
•
•
discrimination better than 20%;
latching alarm plus reset;
relay output 0.5A at 125VAC.
Minimum current 3A. If load current is below this value make two turns or more
around current transformer. H.B. circuit also diagnose fuse failure.
H.B. circuit reads load current via a current transformer 25-50/0.05 or 100/0.05 depending on
thyristor size.
6.4.1 Heater Break Alarm indication
LED
STATUS
DESCRIPTION
SC
SCR OK
SCR short circuit
HB
Laod OK
Load Fault
= OFF
= ON
= Flashing
The thyristor unit is supplied with a normally closed (N/C) contact.
In alarm condition and without auxiliary voltage the contact is closed (relay coil not
energized). In normal condition (no alarm) the contact is open (relay coil energized).
6.4.2 Reset
To reset Heater Break Alarm open RESET contact on terminal 3-4.
25
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
6.4.3 HB alarm contact
Warning: this procedure can be done just by specialized personnel.
The contact of the H.B. Relay is available on auxiliary terminals.
Terminal Descriprion
10
Common relay HB alarm
11
NO/NC HB relay alarm
To change relay status remove plastic cover and configure jumpers as represented below:
STATUS
RELE STATUS
IN Alarm
Close
Circuit not
powered
Close
OK
Open
IN Alarm
Open
Circuit not
powered
Open
OK
Close
www.cdautomation.com
MAIN PCB
J19
C B A
(std)
C B A
26
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
Main PCB
27
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
6.4.4Calibration
This procedure it’s necessary to give set point to Heater Break. CD3000M reads the load current
many times and when the value is the same for three times takes it as set point.
Calibration procedure:
•
verify that connections are correct;
•
supply the thyristor unit;
•
push “CAL” button on front of CD3000M unit,
or supply with 24Vdc terminals 1-2 or send command via RS485;
•
the thyristor unit goes in conduction state to measure load current;
•
all LEDS are ON, this means that calibration procedure is active;
•
after one minute LEDS for H.B. and S/C switch off (calibration procedure is done);
•
the thyristor unit is ready to work.
www.cdautomation.com
28
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
6.4.5 Digital input Command
Reset
3
4
1
3
4
7
7
8
8
9
10
COM
11
NO/NC
H.B.
Contact
12
13
14
15
16
5
2
POWER UNIT
2
POWER UNIT
1
Reset
9
10
COM
11
NO/NC
H.B.
Contact
12
13
14
15
16
17
17
18
18
6 A2+ A1-
5
6 A2+ A1-
6.4.6 RS485 Command
RS485-A
RS485-B
Reset
2
3
4
1
3
4
7
8
8
9
10
COM
11
NO/NC
H.B.
Contact
12
13
14
15
16
5
2
7
POWER UNIT
POWER UNIT
1
Reset
9
10
COM
11
NO/NC
12
13
14
15
16
17
17
18
18
6 A2+ A1-
H.B.
Contact
5
6 A2+ A1-
If load current decreases for partial or total load failure (sensitivity 20% standard adjustable via
RS485) the yellow LED becomes ON and alarm relay changes status.
If CD3000M is still in conduction with no input signal (LED green OFF) it means that there is a short
circuit on thyristors and red LED (SC) becomes ON.
The diagnostic is active only when the switching period is longer than 60ms (3 main
voltage cycle).
If the load has been changed calibration procedure must be done again.
29
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
7. Thyristor firing mode
7.1 Zero Crossing (ZC)
ZERO CROSSING
ZC firing mode is used with Logic Output from
temperature controllers and the Thyristor
operates like a contactor. The Cycle time is
performed by temperature controller. ZC
minimizes interferences because the Thyristor
unit switches ON-OFF at zero voltage.
VOLTAGE SUPPLY (V)
LOAD VOLTAGE (V)
SSR from controller
7.2 Burst Firing (BF)
This firing performed in Digital mode in CD
Automation Thyristor unit gives a lot of
advantages because switches Thyristor at
zero voltage crossing without EMC
interferences. Analog input is necessary for
BF and can be decided how many complete
cycles we want at 50% of power demand.
This value can be implemented from 1 to 255
complete cycles doing the firing less or more
fast. When 1 is setted the firing name
becomes Single Cycle (see above).
20%
50%
VOLTAGE SUPPLY (V)
70%
100%
www.cdautomation.com
30
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
7.3 Configurator
To configure CD3000M unit, you can download the free software and the Configurator Manual from
our web site www.cdautomation.com.
To configure the unit you can use the standard communication on terminals 7-8 or use a
programming cable.
31
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
To connect the programming cable to the thyristor unit, remove cover as in picture.
PROG.
CONN.
Once removed the cover, put a side of cable in prog connector(K10) and the other side in the PC
RS232(9PIN) serial port.
www.cdautomation.com
32
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
8. Fuse and fuseholder for UL certification unit
8.1 Fuse and Fuse Code
The thyristor unit must be protected by fuses against short circuit selecting the proper I²t that
must be lower than thyristor one. The same caution must be taken if Circuit Breaker is used.
Remember that is very difficult to protect the thyristor if this choise is done.
WARNING!! USE SEMICONDUCTOR FUSES ONLY WITH proper I2t
Sizes
Bussmann Div
Cooper (UK) Ltd
(200 kA RMS Symmetrical A.I.C.)
Ferraz Shawmut SA
(200 kA RMS Symmetrical A.I.C.)
Ratings / tailles
Fuse Mod. No.
/fusible modéle Current
I2t
V ac
2
(ARMS) (A sec)
Fuse Mod. No.
/fusible modéle
Ratings / tailles
Current
I2t
Vac
2
(ARMS) (A sec)
Qty
15A
FWC 16A10F
16
150
600
660 Grb 10-16
16
145
660
3
30A
FWC 40A14F
40
980
600
CP URC 14x51/40
40
700
660
3
45A
FWP 50A14F
50
1800
700
CP URC 14x51/50
50
1500
660
3
60A
FWP 80A22F
80
5100
700
CP URD 22x58/80
80
3800
660
3
75A
- -
- -
- -
- -
CP URQ 27x60/100
100
3210
660
3
90A
- -
- -
- -
- -
CP URQ 27x60/125
125
6970
660
3
High speed fuses are only used for the thyristor protection and can not be used to
protect the installation.
The user installation must be protect by electromagnetic circuit breaker or by fuse
isolator.
The warranty of thyristor is null if no proper fuses are used. See tab above.
33
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
8.2 FuseHolder size
30-45A
77 mm
60 mm
15A
80 mm
17mm
26mm
110 mm
75-90A
77 mm
107 mm
60 A
37mm
9 mm
150 mm
www.cdautomation.com
35mm
70 mm
34
9 mm
125 mm
19 mm
6mm
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
9. Fuse and fuseholder for CE mark unit
9.1 Fuse and Fuse Code
The thyristor unit must be protected by fuses against short circuit selecting the proper I²t that
must be lower than thyristor one. The same caution must be taken if Circuit Breaker is used.
Remember that is very difficult to protect the thyristor if this choise is done.
WARNING!! USE SEMICONDUCTOR FUSES ONLY WITH proper I2t
CD3000 SERIE
I²T (max)
(A² sec.)
Size and current
Fuse and
Fuseholder
CODE
Fuse
CODE
15
600
10,3X38 / 16A
FFH1038/16A
FU1038/16A
30
980
14X15 / 40A
FFH1451/40A
FU1451/40A
45
1800
14X15 / 50A
FFH1451/50A
FU1451/50A
60
5100
22x58 / 80A
FFH2258/80A
FU2258/80A
75
10000
22X58 / 100A
FFH2258/100A
FU2258/100A
90
15000
27X60 / 125A
FFH2760/125A
FU2760/125A
High speed fuses are only used for the thyristor protection and can not be used to
protect the installation.
The user installation must be protect by electromagnetic circuit breaker or by fuse
isolator.
The warranty of thyristor is null if no proper fuses are used. See tab above.
35
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
9.2 FuseHolder size
30-45A
77 mm
60 mm
15A
80 mm
17mm
26mm
110 mm
90A
77 mm
107 mm
60-75A
37mm
9 mm
150 mm
www.cdautomation.com
35mm
70 mm
36
9 mm
125 mm
19 mm
6mm
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
10.Modbus communication
The CD3000M is equipped with two-wire RS485-compatible serial communications, by
which means communication may occur between the Controller and a master device
(e.g. a computer or terminal).
10.1 Physical requirements
10.1.1 Character Transmission
Data format is fixed to be one start bit, eight data bits, one stop bit, baud rate 9600 and the parity
none.
10.2 ModBus RTU protocol
The standard RS485 Communications uses the industry standard MODBUS RTU protocol.
The following restrictions are imposed:
•
•
Baud rates is fixed to 9600 Baud only.
Support for multi-parameter Write operations is limited to support of the MultiWord Write Function (Number 16) but it permits the writing of only one
parameter per message.
The following MODBUS functions are supported:
Function
Read Holding Registers (Read n Word)
Preset Multiple Registers (Write n Word)
Function Number
03
16
The Controller will identify itself in response to a Read Holding Registers message which enquires the
values of word parameters 121 and 122 (see Table 4-2).
MODBUS Function 17 (Report Slave ID) is not supported.
10.2.1Message Formats
The first character of every message is the Controller address, in the range 1 - 255 and 0 for
broadcast messages.
The second character is always the Function Number.
The contents of the remainder of the message depends upon this Function Number.
In most cases the Controller is required to reply to the message by echoing the address and
Function Number.
Broadcast messages are supported at address 0 (to which the CD3000M responds by
taking some action without sending back any reply).
Data is transmitted as eight-bit binary bytes with one start bit, one stop bit and parity checking set
to none. A message is terminated simply by a delay of more than three character lengths at the
Baud rate used(in this case 9600 baud); any character received after such a delay is considered to
be the potential address at the start of a new message.
37
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
Since only the RTU form of the protocol is supported, each message is followed by a two-byte
CRC 16 (a 16-bit cyclic redundancy checksum).
This checksum is calculated in accordance with a formula which involves recursive division of the
data by a polynomial, with the input to each division being the remainder of the results of the
previous division.
The dividing polynomial is
216 + 215 + 22 + 1(Hex 18005)
but this is modified in two ways:
•
•
because the bit order is reversed, the binary pattern is also reversed, making the most
significant bit (MSB) the right-most bit;
because only the remainder is of interest, the right-most (most significant) bit can be
discarded.
Thus, the polynomial has the value Hex A001.
10.2.2 Bit’s order
Normal bit order
Most significant bit
Least significant bit
Most significant byte Least significant Byte
Reversed bit order
Least significant bit
Most significant bit
Least significant Byte
Most significant byte
N.B.: Reversed order apples, so CRC16 return Reversed bit order
www.cdautomation.com
38
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
CR= CRC error check data (1 word)
I = Digits of calculation characters
in command message
J = Check on the number of times
of CR calculation
START
Setting FFFF (Hex) To CR
Setting 1 to I
Exclusive logical Sum (XOR) is executed on one character (1 byte) at I
charactor of CR and designated message, and results are set to CR.
Setting 1 to J
Bit at right and of CR is 1?
NO
CR is shifted by
1 bit to right
YES
After shifting CR by 1 bit to right, A001(Hex) and exclusive logical sum
(XOR) are executed for setting the result in CR
Added 1to J
NO
Eight times of calculation
is completed?
J>8
YES
Added 1 to I
NO
Calculation of all charactersis completed?
I>All characters numbers
YES
END
39
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
10.2.3 C Language CRC 16 Example
static short CRC16 (unsigned char *p_first,unsigned char *p_last)
{
unsigned int crc=0xffff;
short j;
for (;p_first<=p_last;p_first++)
{
crc ^= *p_first;
for(j=8;j>0;j--)
{
if(crc & 0x0001)
{
crc = crc >> 1;
crc ^= 0xA001;
}
else
{
crc = crc >> 1;
}
}
}
return (crc);
}
10.2.4 Read Holding Registers (Read n Words) – Function 03
The message sent to the Controller to obtain the value of one or more registers comprises the
following eight bytes:
Addr. unit
Func.
3
3Hex
Address
1° word
HI
LO
N° of Word
CRC 16
HI
HI
LO
LO
The normal reply will echo the first two characters of the message received followed by a singlebyte data byte count (which will not include itself or the CRC).
For this message, the count value equals the number of parameter values read multiplied by two.
Following the byte count, the specified number of parameter values are transmitted, followed by the
CRC16 bytes:
Addr. unit
Func.
3
3Hex
www.cdautomation.com
Cont.
1° Value
HI
LO
40
Last Value
CRC 16
HI
HI
LO
LO
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
10.2.5 Preset Multiple Registers (Write n Words) - Function 16
This is an eleven-byte message. only one parameter may be written for each received message.
The usual pre-amble is followed by the address of the parameter to be written, a two-byte word
count (always set to 1), a single-byte byte count (always set to 2), the value to be written and
the CRC16 bytes:
Addr. unit
Func.
16
10Hex
Addr of
1° Word
HI
LO
N° of Word
Cont.
Valore
0
2
HI
1
CRC 16
LO
HI
LO
The Controller normally responds with the following eight-bit reply:
Addr. unit
Func.
N° of Word
N° Word
16
10Hex
HI
0
LO
CRC 16
1
HI
LO
10.2.6 Error and Exception Responses
If a received message contains a corrupted character (parity check failure, framing error etc.) or if
the CRC16 check fails, or if the received message is otherwise syntactically flawed (e.g. byte count
or word count is incorrect), the thyristor will ignore that message.
If the received message is syntactically correct but nonetheless contains an illegal value, the
thyristor will send a five-byte exception response as follows:
Addr. unit
Func.
N.Exception
CRC 16
HI
LO
The Function Number byte contains the function number contained in the message which caused
the error, with its top bit set (i.e. Function 3 becomes 0x83) and the Exception Number is on of the
following codes:
Code
1
2
3
Name
ILLEGAL FUNCTION
ILLEGAL DATA ADDRES
ILLEGAL DATA VALUE
Cause
Function number out of range
Parameter ID out of range or not supported
Attempt to write invalid data/required action not
executed
NOTE: Writing a parameter value equal to its current value is a valid transaction; this will
not cause an error response.
41
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
10.3 Word parameters
Parameter
N.
Notes
Heater nominal current
1
Read only
Set-point HB
2
Read /write
3
Read only
4
Read /write
Status Table (shown in
Comand Table (shown in
Tab 2.1.2)
Tab 2.1.3)
Output Power (0 – FFH)
5
Power Adjust (0 – FFH)
6
Read - (Write if BIT1in Command table i = 1)
(0->0% - FF->100%)
Read -- (Write if BIT1in Command table i = 1)
(0->0% - FF->100%)*
10.3.1 Heater nominal current
Operation: Read
Parameter 1
Meaning:
It correspond at one value in points (0-255,0-FF Hex).
It represents average current value flowing into thyristors.
Value depends on current transformer ratio that is different from one size to the other one (see
below table)
Nominal current
(A)
3,5
15
25
35
45
60
90
110
www.cdautomation.com
Zero (0 , 0 Hex)
(A)
0
0
0
0
0
0
0
0
Max ( 255 , ff Hex)
(A)
3,5
25
25
50
50
100
100
100
42
User’s Manual
CD3000M-3PH up to 90A
10.3.2 Set-point HB
Operations: Read/Write
C.D. Automation Srl
Parameter 2
Meaning:
It correspond at one value in points (0-255, o-FF Hex). It’s the set of current value below which HB
alarm occurs.
This value is the load current minus % value of parameter 124H. This value depend on nominal
current of transformer that change in function of thyristor nominal current as described in below
tab.
Nominal current
(A)
3,5
15
25
35
45
60
90
110
Zero (0 , 0 Hex)
(A)
0
0
0
0
0
0
0
0
Max ( 255 , ff Hex)
(A)
3,5
25
25
50
50
100
100
100
10.3.3 Status Table
Operations: Read
Parameter 3
Meaning:
It’s a tab in bit that represent the “Status” of thyristor unit
10.3.4 Comand Table
Operations: Read/Write
Parameter 4
Meaning:
It’s a tab in bit for remote commands via RS485 (see tab)
43
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
10.3.5 Output Power
Command from controller
Operations: Read
Parameter 5
Meaning:
It rapresent a value in points (0-255, 0-FF Hex) and it’s the power demand in % of controller.
Example:
0%
=0
50%
= 128
100%
= 255
0 (Hex)
80 (Hex)
FF (Hex)
Command via RS485
Operations : Read/Write
Meaning:
It’s a value in points (0-255, 0-FF Hex)
It’s power set point setted in thirst buffer
Example:
0%
=0
50%
= 128
100%
= 255
0 (Hex)
80 (Hex)
FF (Hex)
10.3.6 Power adjust
Operations: Read/Write
Parameter 6
Meaning:
Its’ a value in points (0-255, 0-FF Hex)
Its’ a scaling factor of power demand
Example 1:
0%
=0
50% = 128
100% = 255
Example 2:
•
•
•
Output Power :100
Power Limit :100
-> Power real : 100
Output Power :100
Power Limit :50
-> Power real : 50
Output Power :80
Power Limit :50
-> Power real : 40
www.cdautomation.com
OUT %
Power Adjust = 100%
100
Power Adjust = 80%
80
60
Power Adjust = 40%
40
20
0
20
40
44
60
80
100 Input %
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
10.3.7 Status Table
Bit
Meaning
Notes
0
Short circuit on SCR
Read only
1
Load Failure
Read only
2
On-Off
Read only
3
HB Calibration in progress
Read only
0=Normal
10.3.7.1 Short circuit on SCR
-
1=Calibration
Bit 0
Operations: Read
Meaning:
Its’ a status but that represents the short circuit on thyristor
0
1
= OK
= Short circuit
10.3.7.2 Load Failure
Bit 1
Operations: Read
Meaning:
It’s a bit that represent partial or total load failure.
0
1
= OK
= Load failure
10.3.7.3 On-Off
Bit 2
Operations: Read
Meaning:
It’s a bit that represent when input signal is ON
0
1
= Input signal OFF
= Input signal ON
10.3.7.4 HB Calibration in progress
Bit 3
Operations: Read
Meaning:
It’s a bit status that represent “calibration in progress”
0
1
= No calibration
= Calibration in progress
45
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
10.3.8 Command Table
Bit
Meaning
Notes
0
HB Calibration
Read /write
0=Off ( normal mode set to 0)
1
Firing command
Read /write
0=from terminal -
1=from RS485
2
On-Off
Read /write
0=Off -
1=On
1=ACTVATE Calibration
Read /write
0=Off ( normal mode set to 0)
N.B.: When unit is switch off all command parameter are set to 0
3
RESET HB
1=RESET
10.3.8.1 HB Calibration
Bit 0
Operations: Read / Write
Meaning:
It’s a bit that starts the HB calibration procedure
When this bit is zero start the calibration procedure and reset itself automatically at the end.
10.3.8.2 Firing command
Bit 1
Operations: Read / Write
Meaning:
It’s a command bit used to switch from analog external command to command via RS485
0
1
= Command of analog input
= Command of RS485 input
10.3.8.3 On-Off
Bit 2
Operations: Read / Write
Meaning:
Its’ an enable bit to switch ON-OFF the power.
0
1
= Power disabled
= Power enabled
10.3.8.4 HB RESET
Bit 3
Operations: Read / Write
Meaning:
It’s a command bit to reset HB alarm.
This parameter has to be at 0 to have the alarm working properly
0
1
= Reset disabled
= Reset enabled
www.cdautomation.com
46
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
10.4 Thyristor unit Configuration
Parameter
N.
Notes
Password
123
Write
Delay trigger
124L
Read /write
% HB
124H
Read /write
Firing type
125L
Read /write
Soft start time
125H
Read /write
N° burst
126L
Read /write
Delay time HB
126H
Read /write
Max power for SSR Input
127L
Read /write
Cycle time
127H
Read /write
N° of half period for Delayed triggering
128L
Read /write (Mantenere a 1)
128H
Read /write
10.4.1 Password
Operations: Write
Parameter 123
Meaning:
If properly setted give the access to configuration
10.4.2 Delay triggering
Operations: Read/Write
Parameter 124L
Meaning:
It’s correspond to a value in points (0-50, 0-32 Hex)
Each step is 0,1msec. Range is 0-5msec.
This parameter is the delay of firig in first half period with respect zero voltage crossing.
10.4.3 % HB
Operations: Read/Write
Parameter 124H
Meaning:
It’s correspond to a value in point (0-255, 0-ff Hex)
This parameter is the value in % that decrease the load current to establish the HB current set
point
Example:
Load current
Parameter 124H
Parameter 2 will be setted at 8A
= 10A
= 20%
51 Dec
47
33 Hex
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
10.4.4 Firing type
Operations: Read/Write
User’s Manua
Parameter 125L
Meaning:
Selection table of firing modes.
Value
Type
Option
H
L
0
1
Zero Crossing
-
0
2
Single Cycle
-
0
3
Burst
-
1
1
Zero Crossing
Soft Start
1
2
Single Cycle
-
1
3
Burst
Soft Start
2
1
Zero Crossino
Delay trigger
2
2
Single Cycle
2
3
Burst
Delay triggering
2
4
Phase angle
Soft start
10.4.5 Soft start time
Parameter 125H
Operations: Read/Write
Meaning :
It’s correspond to a value in points (0 – 255, 0 – FF Hex).
Each step is 5msec .
OUT
The unit start in phase angle mode with a ramp starting from
zero up to full voltage in a presetted and Adjustable time.
The time is setted by this parameter.
Soft Start Time
Par 125H x 5msec
Time
Value of this parameter must be less than cycle time.
For burst firing:
Value of this parameter must be less than:
50Hz -> 20msec
x Number of cycles (Parameter 126L).
60Hz -> 16,6msec x Number of cycles (Parameter 126L).
www.cdautomation.com
48
User’s Manual
CD3000M-3PH up to 90A
10.4.6 N° burst
Operations: Read/Write
C.D. Automation Srl
Parameter 126L
Meaning:
It’s a value in point (0 – 255, 0 – FF Hex).
In burst firing mode it rapresents the number of cycles at 50% power demand
10.4.7 Delay time HB
Operations: Read/Write
Parameter 126H
Meaning:
It’s a value in point (0 – 255, 0 – FF Hex).
Each step is 50msec.
It represent a delay to have HB alarm active
When is used soft start this time must be longer than soft start time.
Par126H x 50msec > Par125H x 5msec
When zero crossing firing is used must be less than cycle time
Par126H x 50msec > Par127H x 50msec
10.4.8 Max power for SSR Input
Operations: Read/Write
Parameter 127L
Meaning:
It’s a value in points (0 – 255, 0 – FF Hex).
When SSR input is used it represent the value of the power (%) when is in ON status.
It’s the power % when firing command is given on RS485 (1).
Example:
0%
50%
=0
= 128
0 (Hex)
80 (Hex)
100%
= 255
FF (Hex)
49
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
10.4.9 Cycle time
Operations: Read/Write
Parameter 127H
Meaning:
It’s a value in points (0 – 255, 0 – FF Hex).
Each step is 50msec .
ON OFF
20%
50%
70%
100%
Time
Cycle Time
When single cycle (SC) and burst firing (BF) is used must be setted at 240 (FO Hex)
When SSR input is used set at 240 (FO Hex)
When is used zero crossing (ZC) represents the cycle time
(ON time + OFF time, default 60(3C Hex) )
10.4.10 Number of half periods for DT firing
Operations: Read/Write
Parameter 128L
Meaning:
Must be setted at 1.
www.cdautomation.com
50
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
10.5 Address configuration
To Configure communication address remove cover and set the
dip-switch as below specified.
8
7
6
5
4
3
2
1
ON OFF
10.5.1 Address table
ID
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
8
-
7
-
6
-
5
X
X
X
X
X
X
X
X
X
X
4
X
X
X
X
X
X
X
X
X
X
3
X
X
X
X
X
X
X
X
X
X
X
X
-
2
X
X
X
X
X
X
X
X
X
X
X
X
-
1
X
X
X
X
X
X
X
X
X
X
X
X
X
ID
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
8
-
7
-
6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
5
X
X
X
X
X
X
X
X
X
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
3
X
X
X
X
X
X
X
X
X
X
X
X
-
2
X
X
X
X
X
X
X
X
X
X
X
X
X
1
X
X
X
X
X
X
X
X
X
X
X
X
-
www.cdautomation.com
C.D. Automation Srl
ID
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
8
-
7
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
www.cdautomation.com
CD3000M-3PH up to 90A
5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
3
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
ID
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
52
8
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
User’s Manua
7
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
3
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
User’s Manual
ID
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
CD3000M-3PH up to 90A
8
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
7
X
X
X
X
X
X
X
X
X
6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
X
-
=
=
ON
OFF
5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
3
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
ID
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
53
8
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
C.D. Automation Srl
7
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
3
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
User’s Manua
11. Maintenance
11.1 Trouble Shooting
Small problems sometimes can be solved locally with the help of the below tab of trouble shooting.
If you don’t succeed, contact us or your nearest distributor.
Symptom
Thyristor unit
doesn’t go in
conduction with
input signal.
Indication on
front unit
Green LED is
always light
off.
Green LED
(PW) light on
and green LED
(ON) in light off
condition.
Green LED
(PW) in light
on condition
and green LED
(ON) in light on
condition.
Possible reasons of the symptom
No voltage auxiliary power
supply to terminals 1 -3 (see
wiring diagram).
No input signal.
Reversed polarities of input
signal.
Reset contact in open condition
(see wiring diagram).
Fuse failure.
Load failure.
Load connection interruption.
Thyristor faulty and always in
open circuit.
With HB option the yellow led
(HB) in light on condition.
Short circuit on thyristor. If
there is HB circuit the red LED
(SC) is light on.
-
Give auxiliary voltage supply
to terminals 1-3.
-
Provide to give input signal.
Reverse the input signal
polarity.
Make link on reset terminals.
-
Substitute the thyristor.
Check that load is not in
short circuit.
HB circuit not tuned.
Current transformers not
properly wired (if are external
to CD3000).
-
-
HB circuit not properly tuned.
-
Push CAL button in front unit
to start HB calibration
procedure.
Control current transformers
wiring and Push CAL button
in front unit to start HB
calibration procedure.
Push CAL button in front unit
to start HB calibration
procedure.
-
Wrong input signal selection.
Wrong input signal calibration
(out of range).
Auxiliary voltage supply out of
limits.
-
-
-
Load current
flows also with
no input signal.
Green LED
(ON) always in
light off
condition.
Current flows at Yellow HB in
nominal value
light on
but yellow LED
condition.
(HB) in light on
condition.
Red LED (SC) is
lighted also if
current is at
nominal value.
Thyristor unit
doesn’t work
properly.
Red LED in
light on
condition.
-
www.cdautomation.com
Actions
54
-
-
-
Substitute the fuse.
Repair the load.
Provide to repair the wiring.
Substitute the faulty
thyristor.
Check the load.
Control input signal setting.
Repeat input calibration
procedure.
Verify the auxiliary voltage
supply.
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
11.2 Repairing procedure
•
•
•
•
•
Phone to us.
Explain to Service Engineer the problem because sometimes it can be solved with a phone call.
If this is not possible ship the unit to us or to your distributor.
Write a fault description and give the name of your personnel to which refer.
Use a rugged packaging to ship the unit.
11.3 Fans
The thyristor unit with forced ventilation uses fans that rotate permanently when the unit is
supplied. In case of accidental fan failure, there is an over heating temperature on heatsink. In this
case to give protection to thyristor there is a thermal switch properly setted. The function of this
switch is to open the input signal until the heatsink temperature falls below the setted value. This
means that also with input signal in ON condition the unit is switched OFF and the system can not
work at full power. For these reason is important to control periodically the fan status checking that
is rotating.
11.4 Servicing
In order to have correct cooling, the user must clean the heatsink and the protective grill of fan.
The frequence of this servicing depends on environmental pollution.
Check periodically also if the screw for the power cables and safety earth are tightened correctly
11.5 Warranty conditions
We gives a 12 months warranty to its products. The warranty is limited to repairing and parts
substitution in our factory and does exclude products not properly used and fuses.
Warranty does not includes products with serial numbers deleted. The faulty product should be
shipped to us at your cost and our Service will evaluate if product is under warranty terms.
Substituted parts remains our property.
55
www.cdautomation.com
C.D. Automation Srl
CD3000M-3PH up to 90A
12. CD Automation’s distributors
For a more precise and rapid service, please contact the distributor nearest to you:
ITALY
CABE S.r.l.
Via Ferrara, 15/17
40018 S. Pietro in Casale (BO)
Tel: 051 6661345
Fax: 051 6661283
Sig. Bergonzoni
[email protected]
Vectra Misure S.r.l.
Via Gaidano, 109/17
10137 Torino (TO)
Tel: 011 3097003
Fax: 011 3098799
Sig. Cochis
[email protected]
CEAM Control Equip. S.r.l.
Via Val d'Orme, 291
50053 Empoli (FI)
Tel: 0571 924181
Fax: 0571 924505
Sig. Campinoti
[email protected]
Secif S.a.s.
Via Bachelet, 27
35010 Busa di Vigonza (PD)
Tel: 049 8934422
Fax: 049 8934415
Sig. Ferro
[email protected]
Studio Rapaccini S.a.s.
Via del Rivo, 138
05100 Terni (TR)
Tel: 0744 305105
Cell: 335 6163428
Fax: 0744 305110
Dott. Rapaccini
[email protected]
INTERNATIONAL DISTRIBUTORS
PICS NV
Middelmolenlaan, 110
2100 Deurne
Belgium
Tel: +32 332 65959
Fax: +32 332 66770
Mr. Berge Billiauws
http://www.pics.be
OY E Sarlin AB
PL-750
00101 Helsinki
Finland
Tel: +358 950444259
Fax: +358 95666951
Mr. Tapio Ala Ketola
http://www.sarlin.com
Hengstler Div. Cont. Ind.
94-106 Rue B. Pascal Z.I. des Mardelles
93602 Aulnay Sous Bois Cedex
France
Tel: +33 148795541
Fax: +33 1498795561
Mr. Laurent Mulley
Mesa Industrie-Elektronik GmbH
Elbestr., 10
45768 Marl
Germany
Tel: +49 2365915220
Fax: +49 2365915225
Mr. Peter Hallwas
Hengstler GmbH
Uhlandst, 49
D-78554 Aldingen
Germany
Tel: +49 7424890
Fax: +49 742489500
Mr. Armin Belle
Toshniwal Instruments Mfg Pvt Ltd
PO Gagwana Pin
305023 Dist. Ajmer
India
Tel: +91 145420506
Fax: +91 145420505
Mr. Ravi Toshniwal
www.cdautomation.com
56
User’s Manua
User’s Manual
CD3000M-3PH up to 90A
C.D. Automation Srl
CasCade Automation Systems BV
Ridderhaven, 16
2984 BT Ridderkerk
The Netherlands
Tel: +31 180463870
Fax: +31 180485921
Mr. Patrick Braams
http://www.casca de-a-s.com
[email protected]
Paragon Alliance
30, Summerhill Drive - Felpham
PO22 6AS Bognor Regis - West Sussex
England
Tel: +44 1243587170
Fax: +44 1243587270
Mr. Jeremy Watson
http://www.paragonalliance.co.uk
[email protected]
Teck Instrument AS
Verksveien, 7
N-3330 Skotselv
Norway
Tel: +47 32 241300
Fax: +47 32 241301
Mr. Johan Pette r Haffner
http://www.teck.no
[email protected]
LA-Konsult AB
Agatan, 1
73440 Hallstahammar
Sweden
Tel: +46 22010905
Fax: +46 22010403
Mr. Leif Johansson
http://www.la -konsult.se
[email protected]
SRC Sistemas de Regulacion y Control, SL
Avda. del Cantabrico, 11. Pabellon, 6
Poligono Industrial Betoño
01013 Vitoria-Gasteiz (Alava)
Spain
Tel: +34 945259455
Fax: +34 945258852
[email protected]
http://www.srcsl.com
CONTROLTEMP, SL
C/ Rafael Casanovas, 21 local.
08130 Sta Perpetua de Mogoda
Barcelona
Spain
Tel: +34 935741320
Fax: +34 935744116
[email protected]
http://www.controltemp.net
CRA - Mess-, Regel- + Antriebstechnik AG
Stampfstrasse, 74
CH-8645 Jona
Switzerland
Tel: +41 552126959
Fax: +41 552126960
Mr. Chiauzzi
http://www.cra.ch
[email protected]
Danaher Corporation
1675 Delany Road
Gurnee, IL 60031-1282
USA
Tel: +1 8473605310
Fax: +1 8476626633
Mr. Andrew Ross
http://www.dancon.com
[email protected]
Electronica Francisco Palma Saavedra
Av. Amerigo Vespucio 513-B
Villa Alto Jahuel, 2 - Pudahuel - Santiago
Chili
Tel: +56 27482023
Fax: +56 27482032
Mr. Francisco Palma S.
[email protected]
Beta Technic Aps
Bygstubben, 5
DK - 2950 Vedbaek
Denmark
Tel: +45 45662208
Fax: +45 45662206
Sune Granzow
http://www.betatechnic.dk
Bresimar LDA
Quinta Do Simao en 109 Esgueira
997 Aveiro
Portugal
Tel: +351 214951760
Fax: +351 234303329
Mr. Carlos Breda
ENG CD3000M 3PH up to 90A.doc
57
www.cdautomation.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement