ELATION TVL F1CW - USER MANUAL 1.2

ELATION TVL F1CW - USER MANUAL 1.2
E L A TI ON | TVL F1CW™ | user manual 1.2
TVL F1CW™
user manual 1.2 w w w . e l a t i o n l i g h t i n g . c o m ©2013 ELATION PROFESSIONAL all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-­‐ELATION brands and product names are trademarks or registered trademarks of their respective companies. ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product. Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 | 323-832-9142 fax | www.elationlighting.com | [email protected]
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, Netherlands
+31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | [email protected]
2 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m CONTENTS
General Information
4
Warranty
6
Safety Instructions
7
General Guidelines
8
Fixture Overview
9
Installation
10
Understanding DMX
13
Fixture Menu
17
DMX Channel Functions and Values
21
Cleaning and Maintenance
22
Technical Specifications
23
Optional Accessories
25
3 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m GENERAL INFORMATION
INTRODUCTION
Congratulations, you have just purchased one of the most innovative and reliable lighting
fixtures on the market today! The TVL F1CW™ has been designed to perform reliably for
years when the guidelines in this booklet are followed. Please read and understand the
instructions in this manual carefully and thoroughly before attempting to operate this unit.
These instructions contain important information regarding safety during use and
maintenance.
UNPACKING
Thank you for purchasing the TVL F1CW™ by Elation Professional®. Every TVL F1CW™
has been thoroughly tested and has been shipped in perfect operating condition.
Carefully check the shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your unit for damage and be sure
all accessories necessary to operate the unit have arrived intact. In the event damage
has been found or parts are missing, please contact our customer support team for
further instructions. Please do not return this unit to your dealer without first contacting
customer support at the number listed below. Please do not discard the shipping carton
in the trash. Please recycle whenever possible.
BOX CONTENTS
•
•
•
•
(1) powerCON Cable
(1) Gel Frame Holder
(1) Rotating Barn Door + Holder
Manual & Warranty Card
M A N U A L
U P D A T E S
Please check www.elationlighting.com for the latest revision/update of this manual.
4 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m CUSTOMER SUPPORT
Elation Professional® provides a customer support line, to provide set up help and to
answer any question should you encounter problems during your set up or initial
operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation
Professional®. Service Hours are Monday through Friday 8:00 a.m. to 5:00 p.m. PST.
Voice: 323-582-3322
Fax: 323-832-9142
E-mail: [email protected]
Forum: www.ElationLighting.com/forum
WARRANTY REGISTRATION
The TVL F1CW™ carries a two year (730 days) limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service items whether
under warranty or not, must be freight pre-paid and accompany a return authorization
(R.A.) number. The R.A. number must be clearly written on the outside of the return
package. A brief description of the problem as well as the R.A. number must also be
written down on a piece of paper and included in the shipping container. If the unit is
under warranty, you must provide a copy of your proof of purchase invoice. Items
returned without a R.A. number clearly marked on the outside of the package will be
refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at 323-582-3322.
I M P O R T A N T
N O T I C E !
There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. Damages resulting from
modifications to this fixture and/or the disregard of safety and general user
instructions found in this user manual void the manufactures warranty and are
not subject to any warranty claims and/or repairs.
5 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m 2-YEAR LIMITED WARRANTY
A.
Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free
of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of
purchase. This warranty shall be valid only if the product is purchased within the United States of America,
including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase
by acceptable evidence, at the time service is sought.
B.
For warranty service, send the product only to the Elation Professional® factory. All shipping charges must
be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this
warranty, Elation Professional® will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be
shipped with the product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which Elation Professional® concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the Elation Professional® factory unless prior
written authorization was issued to purchaser by Elation Professional®; if the product is damaged because not
properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning or periodic
check-up. During the period specified above, Elation Professional® will replace defective parts at its expense,
and will absorb all expenses for warranty service and repair labor by reason of defects in material or
workmanship.
The sole responsibility of Elation Professional® under this warranty shall be limited to the
repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional®. All
products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
effect.
E.
Elation Professional® reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore manufactured.
F.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made by
Elation Professional® in connection with this product, including warranties of merchantability or fitness, are
limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied,
including warranties of merchantability or fitness, shall apply to this product after said period has expired. The
consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above;
and under no circumstances shall Elation Professional® be liable for any loss or damage, direct or
consequential, arising out of the use of, or inability to use, this product.
G.
This warranty is the only written warranty applicable to Elation Professional® Products and supersedes all
prior warranties and written descriptions of warranty terms and conditions heretofore published.
6 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m SAFETY INSTRUCTIONS
™
The TVL F1CW is an extremely sophisticated piece of electronic equipment. To
guarantee a smooth operation, it is important to follow the guidelines in this
manual. The manufacturer of this device will not accept responsibility for damages
resulting from the misuse of this fixture due to the disregard of the information
printed in this manual.
This device falls under PROTECTION CLASS 1. It’s essential this device is
grounded properly, and only qualified personnel perform all electrical connections.
•
For proper operation, follow the Installation guidelines described in this manual. Only qualified and
certified personnel should perform the installation and only the original rigging parts (brackets, holders,
clamps, safety cables) included with this fixture should be used for installation. Any modifications will void
the original manufactures warranty and increase the risk of damage and/or personal injury.
•
Never look directly into the light source to prevent risk of injury to your retina, which may induce blindness.
Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times.
•
The fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between this fixture
and other devices or a wall for proper cooling.
•
Always disconnect from main power source before performing any type of service and/or cleaning
procedure. Only handle the power cord by the plug end, never pull by tugging the wire portion of the cord.
•
Do NOT operate fixture if the power cord has become frayed, crimped and/or damaged. If the power cord
is damaged, replace it immediately with a new one of similar power rating.
•
Do NOT operate fixture near any flammable materials.
•
Do NOT operate fixture in dusty environments.
7 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m GENERAL GUIDELINES
•
N E V E R
O P E N
T H I S
F I X T U R E
W H I L E
I N
U S E !
•
During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp and will
decrease gradually over time.
•
This fixture is a professional lighting effect designed for use on stage, in studios, retail
stores, nightclubs, theatres, and other similar locations. Do NOT attempt installation
and/or operation without proper knowledge of how to do so.
•
Do NOT permit operation by persons who are not qualified for operating this type of
theatrical fixture. Most damages are the result of operations by nonprofessionals.
•
Consistent operational breaks may ensure the fixture will function properly for many
years to come.
•
Do NOT shake fixture, avoid brute force when installing and/or operating the device.
•
Do NOT connect fixture to a dimmer pack.
•
Always install the fixture with an appropriate safety cable. When installing the fixture
in a suspended environment, always use mounting hardware that is no less than M10
x 25 mm, also be sure the hardware is insert in the pre-arranged screw holes in the
base of the fixture.
•
Please use the original packaging and materials to transport the fixture in for service.
8 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m FIXTURE OVERVIEW
1: Fuse Holder Assembly
2: Power Switch
3: Power IN (powerCON)
4: 5-Pin DMX OUT
5: 5-Pin DMX IN
6: Menu Control Buttons
7: LED Indicators
8: LED Control Display
9: Safety Hook
10: Ethernet (RJ45) Connectors (x2)
1. Fuse Holder Assembly– Houses 250v T3.15A GMA safety fuse. Always replace with
an exact match unless otherwise specified by an authorized Elation Service Technician.
2. Power Switch – Used to power fixture ON or OFF.
3. Power IN – Power connection (powerCON) to power source.
4. 5-Pin DMX OUT – Sends incoming DMX signal to the next fixture in the DMX chain via a
female 5-pin XLR jack.
5. 5-Pin DMX IN – Accepts incoming DMX signal via a male 5-pin XLR jack
6. Menu Control Buttons – Control buttons MENU, UP, DOWN, and ENTER.
7. LED Indicators – LED indicators for DMX, MASTER, SLAVE, and SOUND.
8. LED Control Display – LED control display showing various menus and functions.
9. Safety Hook – Used to connect safety cable to.
10. Ethernet (RJ45) Connectors (x2) – Used to transfer fixture’s information to a main
controller. (CURRENTLY, THESE HAVE NO FUNCTION)
9 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m INSTALLATION
T he el ec tri c c onnec ti on m ust onl y b e c arri ed out b y a qu al if i ed el ec tri c i an. C A U T I O N S
•
The recommended MAX ambient temperature for this fixture is 104°F (40°C).
•
For added protection, mount the fixture in areas outside walking paths, seating areas, or
in areas were unauthorized personnel might reach the fixture.
•
Before mounting the fixture to any surface, make sure the installation area can hold a
minimum point load of 10 times the weight of the fixture.
(350 lbs / 158 kgs)
•
Fixture installation must always be secured with a secondary safety attachment, such as
an appropriate safety cable.
•
Never stand directly below the device when mounting, removing or servicing the fixture.
10 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m MOUNTING POINTS
•
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the device. If you lack these qualifications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
•
Fixture is fully operational in any mounting position, hanging upside-down, or side
mounted, and will remain steady no matter the angle of the fixture head.
•
Be sure the fixture is kept at least 0.5m (1.5 feet) away from any flammable materials
(decoration etc.).
11 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m BARN DOOR & SAFETY CABLE INSTALLATION
4
5
2
1
3
1. Open the spring by hands.
2. Insert the barn door into the outside slot from topside.
3. Open the barn door, and then fasten the safety cable.
4. Insert the barn door into the inside slot from topside.
5. Pull the included Safety Cable through the hole on the backside of the fixture
and over the trussing system or a safe installation point.
This step is a very important to ensure the fixture will not drop if the clamp fails.
12 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m UNDERSTANDING DMX
DMX-512
DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and
controller manufactures as a form of communication between intelligent fixtures and
controllers. DMX allows all makes and models of different manufactures to be linked
together and operate from a single controller. This is possible as long as all the fixtures and
the controller are DMX compliant. A DMX controller sends the DMX data instructions to the
fixture allowing the user to control the different aspects of an intelligent light. DMX data is
sent out as serial data that travels from fixture to fixture via data “IN” and data “OUT” XLR
terminals located on the fixtures (most controllers will only have output jacks).
DMX LINKING
To ensure proper DMX data transmission, always use proper DMX cables and a terminator.
When using several DMX fixtures try to use the shortest cable path possible. Never split a
DMX line with a “Y” style connector. The order in which the fixtures are connected in a DMX
line does not influence the DMX addressing. For example; a fixture assigned a starting DMX
address of 1 may be placed anywhere in the DMX chain, at the beginning, at the end, or
anywhere in the middle. The DMX controller knows to send data assigned to address 1 to
that fixture no matter where it is located in the DMX chain. The TVL F1CW™ can be
controlled via DMX-512 protocol. The TVL F1CW™ is a 2-channel DMX fixture. The DMX
address is set electronically using the controls on the LCD menu.
DATA CABLE (DMX Cable) REQUIREMENTS (For DMX and Master/Slave Operation)
Your fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for
data input and data output (see figure below). If you are making your own cables, be sure to
use two conductor, shielded digital DMX cable rated at 120 ohms; this cable is designed for
DMX transmission and may be purchased from your Elation dealer or at most professional
lighting retailers. Your cables should be made with a male and female XLR connector on
either end of the cable. Also, remember that a DMX line must be daisy chained and cannot
be split, unless using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX
Branch/4™.
13 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m Be sure to follow the above figure when making your own cables. Do not use the
ground lug on the XLR connector. Do not connect the cable’s shield conductor to
the ground lug or allow the shield conductor to come in contact with the XLR outer
casing. Grounding the shield could cause a short circuit and erratic behavior.
DMX-512 CONTROLLER CONNECTION
Connect the provided XLR cable to the female 5-pin XLR output of your controller and the
other side to the male 5-pin XLR input of the TVL F1CW™ (Please refer to the diagram
below.). You can chain multiple panels together through serial linking. The cable that should
be used is two conductor, shielded DMX cable with XLR input and output connectors.
Always be sure daisy chain your in and out data connections, never split or “Y” your DMX
connections unless you are using an approved DMX splitter such as the Elation Opto Branch
4™ or DMX Branch/4™.
Address 1
Address 3
Address 5
Address 7
14 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m DMX-512 CONNECTION WITH DMX TERMINATOR
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt
resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy
chain to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease
the possibilities of erratic behavior.
5-Pin XLR DMX CONNECTORS
Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin.
5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are
readily available at most electric stores. The following chart details a proper cable
conversion.
15 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m DMX ADDRESSING
All fixtures should be given a DMX starting address when using a DMX controller, so the
correct fixture responds to the correct control signal. This digital starting address is the
channel number from which the fixture starts to “listen” to the digital control information sent
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on the back of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX channels) of
each fixture. That means changing the settings of one channel will only affect the selected
fixture.
In the case of the TVL F1CW™, when in 2 channel mode (default can also be set to 1), you
should set the starting DMX address of the first unit to 1, the second unit to 3 (1 + 2), the
third unit to 5 (3 + 2), the fourth unit to 7 (5 + 2) and so on.
Note: During start-up the TVL F1CW™ will automatically detect whether a DMX data signal
is being received or not. If DMX data signal is being received, the display will show
"Addr=XXX" (XXX representing the actual DMX address). If the fixture is not receiving a
DMX signal the display will flash. If your fixture is connected to a DMX controller and the
display is flashing (not receiving a DMX signal), please check the following:
-
The 3-PIN or 5-PIN XLR input plug (cable with DMX signal from controller) is not
connected or is not inserted completely into the DMX input jack of the fixture.
-
The DMX controller is switched off or defective.
-
The DMX cable or connector is defective.
-
A DMX terminator has been inserted into the last fixture in your DMX chain.
16 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m FIXTURE MENU
ON-BOARD SYSTEM MENU
The TVL F1CW™ comes with an easy to navigate system menu. The next section will
detail the functions of each command in the system menu.
LED CONTROL PANEL
The control panel (see image below) located on back of the fixture allows you to access the
system menu and make all necessary adjustments to the TVL F1CW™. To select any menu
functions, press the MENU until the desired menu is displayed. Select the function by
pressing ENTER and the display will flash. Use the UP and DOWN buttons to change the
mode of the menu item. Once the desired mode has been selected, press the ENTER button
to confirm your selection or the display will automatically return to the main menu without
any change after being idle for 60 seconds. Exit a menu at any time without making any
adjustments by pressing the MENU button.
17 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m DMX Address
Press MENU and UP and DOWN buttons to select DMX Address, press the ENTER button
to confirm and the present address will flash on the display. Use the UP and DOWN buttons
to adjust the DMX address from 1 to 512. Once the desired DMX address has been selected,
press the ENTER button to confirm selection. To go back to the functions menu without any
change press the MENU button again. Press and hold the MENU button about one second
or wait for 60 seconds to exit the menu mode.
Slave Mode
Press MENU and UP and DOWN buttons to select Slave Mode, press the ENTER button to
confirm and the present mode will flash on the display. Use the UP and DOWN buttons to
select the Master or Slave Modes. Once the desired mode has been selected, press the
ENTER button to confirm selection. To go back to the functions menu without any change
press the MENU button again. Press and hold the MENU button about one second or wait
for 60 seconds to exit the menu mode.
18 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m Black Out
Press MENU and UP and DOWN buttons to select Black Out, press the ENTER button to
confirm and the present mode will flash on the display. Use the UP and DOWN buttons to
select Yes (yes blackout) or No (no blackout). Once desired the mode has been selected,
press the ENTER button to confirm selection. To go back to the functions menu without any
change press the MENU button again. Press and hold the MENU button about one second
or wait for 60 seconds to exit the menu mode.
Back Light
Press MENU and UP and DOWN buttons to select Back Light, press the ENTER button to
confirm and the present mode will flash on the display. Use the UP and DOWN buttons to
select On (LED ON) or Off (LED OFF). Once the desired mode has been selected, press the
ENTER button to confirm selection. To go back to the functions menu without any change
press the MENU button again. Press and hold the MENU button about one second or wait
for 60 seconds to exit the menu mode
Manual Test
Press MENU and UP and DOWN buttons to select Manu Test, press the ENTER button to
confirm and the present mode will flash on the display. Use the UP and DOWN buttons to
select the Dimmer or Zoom Modes. Once the desired mode has been selected, press the
ENTER button to confirm selection. Use the UP and DOWN buttons to change the value
(0-255). Once the desired mode has been selected, press the ENTER button to confirm
selection. To go back to the functions menu without any change press the MENU button
again. Press and hold the MENU button about one second or wait for 60 seconds to exit the
menu mode.
Dimmer Calibrat
Press MENU and UP and DOWN buttons to select Dimmer Calibrat, press the ENTER
button to confirm and the present mode will flash on the display. Use the UP and DOWN
buttons to adjust the value from 50% to 100%. Once the desired value has been selected,
press the ENTER button to confirm selection. To go back to the functions menu without any
change press the MENU button again. Press and hold the MENU button about one second
or wait for 60 seconds to exit the menu mode.
19 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m Fixture Temp
Press MENU and UP and DOWN buttons to select Fixture Temp, press ENTER button to
confirm and the present mode will flash on the display. Pressing ENTER button will show the
temperature of the unit. To go back to the functions menu without any change press the
MENU button again. Press and hold the MENU button about one second or wait for 60
seconds to exit the menu mode.
Fixture Time
Press MENU and UP and DOWN buttons to select MENU and UP and DOWN buttons to
select Fixture Time, press ENTER button to confirm and the present mode will flash on the
display. Pressing ENTER button will show the temperature of the unit. To go back to the
functions menu without any change press the MENU button again. Press and hold the
MENU button about one second or wait for 60 seconds to exit the menu mode.
Firmware Version
Press MENU and UP and DOWN buttons to select Firmware Version, press ENTER button
to confirm and the present mode will flash on the display. Pressing ENTER button will show
the temperature of the unit. To go back to the functions menu without any change press the
MENU button again. Press and hold the MENU button about one second or wait for 60
seconds to exit the menu mode.
PRO Defaults
Press MENU and UP and DOWN buttons to select PRO Defaults, press ENTER button to
confirm and the present mode will flash on the display. Pressing ENTER button will show the
temperature of the unit. To go back to the functions menu without any change press the
MENU button again. Press and hold the MENU button about one second or wait for 60
seconds to exit the menu mode.
Reset
Press MENU and UP and DOWN buttons to select Reset, press ENTER button and fixture
will reset all functions to factory settings.
20 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m DMX CHANNEL FUNCTIONS AND VALUES
21 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m CLEANING AND MAINTENANCE
CLEANING
Frequent cleaning is recommended to insure proper function and an extended fixture life.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoky,
or dirty surrounding areas can cause greater accumulation of dirt on the fixture’s optics.
•
Clean LED lens with soft cloth surface weekly to avoid dust accumulation.
•
Never use alcohol or solvents.
MAINTENANCE
Regular inspections are recommended to insure proper function and an extended life.
There are no user serviceable parts inside this fixture, please refer all other service issues to
an authorized Elation service technician. Should you need any spare parts, please order
genuine parts from your local Elation dealer.
Please refer to the following points during routine inspections:
•
A detailed electric check by an approved electrical engineer every three months, to make
sure the circuit contacts are in good condition and prevent overheating.
•
Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall
out during normal operation resulting in damage or injury as larger parts could fall.
•
Check for any deformations on the housing, color lenses, rigging hardware and rigging
points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to
enter into the fixture. Damaged rigging points or unsecured rigging could cause the
fixture to fall and seriously injure a person(s).
•
Electric power supply cables must not show any damage, material fatigue or sediments.
Never remove the ground prong from the power cable.
22 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m TECHNICAL SPECIFICATIONS
FEATURES
12° - 40° Motorized Zoom
DMX Controlled Dimmer/Zoom
Flicker FREE Operation for TV and FILM
No Noise Thermo-Optical Cooling Technology
SOURCE
(1) 100W Cool White LED Engine
50,000 Hour Average Life
PHOTOMETRIC DATA
High CRI = 95 / 34.64 Lm/W 5,600K (± 200K)
3,350 Max LUX @5M (12° Full On 5,600K)
EFFECTS
Zoom: 12° - 40°
Dimming: 0% - 100%
CONTROL / CONNECTIONS
4 Button Control LED Menu Display Panel
2 DMX Channels
5pin DMX In/Out
2 Ethernet (RJ45) Ports
powerCON Power In
SIZE / WEIGHT
Length: 20.4” (519 mm)
Width: 16” (407 mm)
Vertical Height: 17.4” (442 mm)
Weight: 35 lbs. (15.8 kg)
ELECTRICAL / THERMAL
AC 100-240V - 50/60Hz
141W Max Power Consumption
40°C / 104°F Max Ambient Temperature
APPROVALS / RATINGS
CE pending
cETLus pending
IP20 Rated
INSTALLATION
Rigging: Clamps (Not Included)
Working Position: Any (360°)
INCLUDED ITEMS
Integrated Yoke/Handle
powerCON Cable
Rotating Barn Door
Gel Frame
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
23 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m PHOTOMETRIC DATA
DIMENSIONAL DRAWINGS
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
24 TVL F1CW™ User Manual 1.2
w w w . e l a t i o n l i g h t i n g . c o m OPTIONAL ACCESSORIES
ORDER CODE
ITEM
TRIGGER CLAMP
Heavy Duty Wrap Around Hook Style Clamp
LSF536
Light Shaping Filter 30° 20” x 24” Sheet
LSF537
Light Shaping Filter 20° 20” x 22” Sheet
LSF538
Light Shaping Filter 60° x 1° 20” x 24” Sheet
LSF559
Light Shaping Filter 10° 20” x 24” Sheet
EWDMXSYSTEM
Wireless DMX System (1 Transmitter, 1 Receiver)
EWDMXT
Wireless DMX Transmitter
EWDMXR
Wireless DMX Receiver
AC5PDMX5PRO
5 ft. (1.5m) 5pin PRO DMX Cable
AC5PDMX10PRO
10 ft. (3m) 5pin PRO DMX Cable
AC5PDMX15PRO
15 ft. (4.5m) 5pin PRO DMX Cable
Additional cable lengths available: 25, 50, 100 ft (7.5, 15.2, 30.5m)
25 TVL F1CW™ User Manual 1.2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement