ST 3000 Smart Pressure Transmitter Series 900 Differential

ST 3000 Smart Pressure Transmitter Series 900 Differential
ST 3000 Smart Pressure Transmitter
Series 900 Differential Pressure Models
Specifications
34-ST-03-65, January 2013
Introduction
In 1983, Honeywell introduced the first Smart Pressure
Transmitter― the ST 3000®. In 1989, Honeywell launched
the first all digital, bi-directional protocol for smart field
devices. Today, its ST 3000 Series 900 Differential Pressure
Transmitters continue to bring proven “smart” technology to a
wide spectrum of pressure measurement applications, from
furnace combustion airflow rate to hydrostatic tank gauging.
The ST 3000 S900 Differential Pressure Transmitter can be
used with any primary flow element to provide proven,
repeatable flow measurement.
All ST 3000 transmitters can provide a 4-20 mA output,
Honeywell Digitally Enhanced (DE) output, HART® output, or
FOUNDATION™ Fieldbus output. When digitally integrated
with Honeywell’s Process Knowledge System™, EXPERION
PKS™, ST 3000 instruments provide a more accurate
process variable as well as advanced diagnostics.
Honeywell’s cost-effective ST 3000 S900 transmitters lead
the industry in reliability and stability:
Figure 1 - Series 900 Differential Pressure Transmitters feature
proven piezoresistive sensor technology.
The devices provide comprehensive self-diagnostics to help
users maintain high uptime, meet regulatory requirements,
and attain high quality standards. S900 transmitters allow
smart performance at analog prices. Accurate, reliable and
stable, Series 900 transmitters offer greater turndown ratio
than conventional transmitters
•
Stability = ±0.01% per year
All ST 3000 transmitters can be ordered to provide one of the
•
Reliability = 470 years MTBF
following output communication options.
Communications options
Models
4-20 mA
STD924
0 to 400 inH2O
0 to 1,000 mbar
STD930
0 to 100 psi
0 to 7 bar
STD974
0 to 3,000 psi
0 to 210 bar
Honeywell Digitally Enhanced (DE)
HART® (versions 5.x or 6.x)
FOUNDATION™ Fieldbus
2
ST 3000 Smart Pressure Transmitter
Description
The ST 3000 transmitter can replace any 4 to 20 mA output
Features
•
Choice of linear or square root output conformity is a
transmitter in use today and operates over a standard twowire system.
simple configuration selection.
•
Direct digital integration with Experion PKS and other
The measuring means is a piezoresistive sensor, which
control systems provides local measurement accuracy to
actually contains three sensors in one. It contains a
the system level without adding typical A/D and D/A
differential pressure sensor, a temperature sensor, and a
converter inaccuracies.
static pressure sensor.
•
Unique piezoresistive sensor automatically compensates
input for temperature and static pressure. Added “smart”
Microprocessor-based electronics provide higher span-
features include configuring lower and upper range
turndown ratio, improved temperature and pressure
values, simulating accurate analog output, and selecting
compensation, and improved accuracy.
The transmitter’s meter body and electronics housing resist
shock, vibration, corrosion, and moisture. The electronics
preprogrammed engineering units for display.
•
Smart transmitter capabilities with local or remote
interfacing means significant manpower efficiency
housing contains a compartment for the single-board
improvements in commissioning, start-up, and ongoing
electronics, which is isolated from an integral junction box.
maintenance functions.
The single-board electronics is replaceable and
interchangeable with any other ST 3000 Series 100 or Series
900 model transmitter.
Advanced Diagnostics
Like other Honeywell transmitters, the ST 3000 features two-
ST 3000 is now available for both HART® 6 and
way communication and configuration capability between the
FoundationTM Fieldbus with advanced diagnostics that
operator and the transmitter through several Honeywell field-
minimize unplanned plant outages, minimize maintenance
rated portable configuration devices, including the Smart
costs and by providing the industry’s most reliable
Field Communicator (SFC) and the Multiple Communication
transmitter.
Configurator (MC ToolKit). While both are made for in-field
•
use, the MC Toolkit also can be ordered for use in intrinsically
safe environments.
The SCT 3000 Smartline® Configuration Toolkit provides an
easy way to configure instruments using a personal
computer. The toolkit enables configuration of devices before
shipping or installation. The SCT 3000 can operate in the
offline mode to configure an unlimited number of devices.
The database can then be loaded down-line during
commissioning.
When digitally integrated with Honeywell’s Experion® Process
Knowledge System or other TDC/TPS systems,
ST 3000 instruments provides local measurement accuracy
to the system level without adding typical A/D and D/A
converter inaccuracies as well as providing advantages from
the many other on-board advanced diagnostic features.
Honeywell’s high-performance ST 3000 S100 transmitters
lead the industry in: Accuracy, Stability, Reliability, Rangeability and Warranty.
Provide advanced warning of possible failure events and
avoid costly shutdowns.
•
Three levels of failure reporting
•
Comprehensive list of on-board diagnostics (Ref. ST
3000 User manual with HART® 6, 34-ST-25-17 Rev:
June 09 and FoundationTM Fieldbus option manual 34ST-25-15 Rev: June 09)
ST 3000 Smart Pressure Transmitter
3
Operating Conditions – All Models
Reference
Condition
(at zero static)
Parameter
Ambient Temperature
Meter Body Temperature
Humidity
Vacuum Region – Minimum
Pressure
All Models Except STD110
mmHg absolute
inH2O absolute
Maximum Allowable
4
Working Pressure (MAWP)
4
25±1
77±2
-40 to 85
77±2
°F
°C
-40 to 185
1
1
-40 to 110
-40 to 230
°F
-40 to 85
°C
°F
-40 to 185 -55 to 125 -67 to 257
-40 to 125 -40 to 257 -55 to 125 -67 to 257
10 to 55
0 to 100
0 to 100
Atmospheric
Atmospheric
25
13
2 (short term2)
2
1 (short term )
0 to 100
3
Maximum Allowable Working Pressure.
MAWP depends on Approval Agency
and transmitter materials of
construction.)
3
°C
Transportation and
Storage
STD924, STD930, STD974 = 4,500psi, 310 bar
Static Pressure Limit = Maximum Allowable Working Pressure (MAWP) = Overpressure
Limit
(ST 3000 products are rated to
2
°F
Operative Limits
Voltage Range: 10.8 to 42.4 Vdc at terminals
Current Range: 3.0 to 21.8 mA
Load Resistance: 0 to 1,440 ohms (as shown in Figure 2)
Supply Voltage, Current, and
Load Resistance
1
°C
25±1
%RH
Rated Condition
For CTFE fill fluid, the rating is -15°C to 110°C (5°F to 230°F); for the STD924 model at temperatures below -15° C (5°F) the URL is
reduced to 100” H2O.
Short term equals 2 hours at 70°C (158°F).
MAWP applies for temperature range -40 to 125°C. However, Static Pressure Limit is de-rated to 3,000 psi from -26°C to -40°C.
Use of graphite o-rings de-rates transmitter to 3,625 psi. Use of adaptor with graphite o-rings de-rates transmitter to 3,000 psi.
Consult factory for MAWP of ST 3000 transmitters with CSA approval.
1440
1200
Loop
Resistance
(ohms)
Note: A minimum of 250 ohms
of loop resistance is necessary
to support communications.
Loop resistance equals barrier
resistance plus wire resistance
plus receiver resistance.
800
650
450
250
= Operating Area
0
10.8
16.28 20.63 25 28.3
Operating Voltage (Vdc)
37.0
42.4
Figure 2 - Supply voltage and loop resistance chart
4
ST 3000 Smart Pressure Transmitter
Performance Under Rated Conditions* - Model STD924 (0 to 400 inH2O/1,000 mbar)
Parameter
Description
Upper Range Limit
inH2O
mbar
400 (39.2°F/4°C is standard reference temperature for inH2O range.)
1,000
Minimum Span
inH2O
mbar
4 Note: Recommended minimum span in square root mode is 20 inH2O (50 mbar).
10
Turndown Ratio
100 to 1
Zero Elevation and Suppression
-5 to ±100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
• Accuracy includes residual error
after averaging successive
readings.
• For FOUNDATIONTM Fieldbus use
Digital Mode specifications.
®
• For HART use Analog Mode
specifications.
In Analog Mode: ±0.075% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (25 inH2O), accuracy equals:


 25 inH 2O 

 span inH 2O 


or ± 0.025 + 0.05

± 0.025 + 0.05
62 mbar 
 in % of span
mbar 

 span
In Digital Mode: ±0.0625% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (25 inH2O), accuracy equals:


 25 inH 2O  or ± 0.0125 + 0.05 62 mbar 




 span mbar 
 span inH 2O 
± 0.125 + 0.05
Zero Temperature Effect per
28°C (50°F)
in % of span
In Analog Mode: ±0.2125% of span.
For URV below reference point (50 inH2O), effect equals:



 span inH 2 O 

± 0.0125 + 0.2


50 inH 2 O

 125 mbar 

 span mbar 
or ± 0.0125 + 0.2

in % of span
In Digital Mode: ±0.2% of span.
For URV below reference point (50 inH2O), effect equals:



 span inH 2 O 
± 0.2

Combined Zero and Span
Temperature Effect per 28°C
(50°F)
50 inH 2 O



 span mbar 
125 mbar
or ± 0.2

in % of span
In Analog Mode: ±0.3% of span.
For URV below reference point (50 inH2O), effect equals:



 span inH 2 O 

50 inH 2 O
± 0.10 + 0.2



 125 mbar 

 span mbar 
or ± 0.10 + 0.02

in % of span
In Digital Mode: ±0.275% of span.
For URV below reference point (50 inH2O), effect equals:



 span inH 2 O 

± 0.075 + 0.2


Zero Static Pressure Effect per
1,000 psi (70 bar)
50 inH 2 O


 50 inH 2O 

 span inH 2O 

in % of span


125 mbar 
 in % of span
span
mbar 


or ± 0.0125 + 0.15

±0.30% of span.
For URV below reference point (50 inH2O), effect equals:


 50 inH 2O 

 span inH 2O 
± 0.15 + 0.15
Stability
 125 mbar 

 span mbar 
±0.1625% of span.
For URV below reference point (50 inH2O), effect equals:
± 0.0125 + 0.15
Combined Zero and Span Static
Pressure Effect per 1,000 psi (70
bar)

or ± 0.075 + 0.2


or ± 0.15 + 0.15

125 mbar 
 in % of span
mbar 

 span
±0.015% of URL per year
* Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and 316 Stainless
Steel barrier diaphragm.
ST 3000 Smart Pressure Transmitter
5
Performance Under Rated Conditions* - Model STD930 (0 to 100 psi/7,000 mbar)
Parameter
Description
Upper Range Limit
psi
bar
100
7
Minimum Span
psi
bar
1
0.07
Turndown Ratio
100 to 1
Zero Elevation and Suppression
No limit except minimum span within ±100% URL.
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability).
In Analog Mode: ±0.075% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (25 inH2O), accuracy equals:


 20 psi 

 span psi 


or ± 0.025 + 0.05

± 0.025 + 0.05
1.4 bar 
 in % of span
bar 

 span
In Digital Mode: ±0.0625% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (20 psi), accuracy equals:


 20 psi 

 span psi 


or ± 0.0125 + 0.05

± 0.0125 + 0.05
Zero Temperature Effect per
28°C (50°F)
1.4 bar 
 in % of span
bar 

 span
In Analog Mode: ±0.1625% of span.
For URV below reference point (30 psi), effect equals:


 30 psi 

 span psi 
± 0.0125 + 0.15


2 bar 
 in % of span
 span bar 
or ± 0.0125 + 0.15

In Digital Mode: ±0.15% of span.
For URV below reference point (30 psi), effect equals:
 30 psi 

 span psi 
± 0.15
Combined Zero and Span
Temperature Effect per 28°C
(50°F)
 2 bar 

 span bar 
or ± 0.15
in % of span
In Analog Mode: ±0.25% of span.
For URV below reference point (30 psi), effect equals:


 30 psi 

 span psi 
± 0.10 + 0.15


 2 bar 

 span bar 
or ± 0.10 + 0.15
in % of span
In Digital Mode: ±0.225% of span.
For URV below reference point (30 psi), effect equals:


 30 psi 

 span psi 
± 0.075 + 0.15
Zero Static Pressure Effect per
1000 psi (70 bar)


 30 psi 

 span psi 


2 bar 
 in % of span
span
bar 


or ± 0.0125 + 0.15

±0.30% of span.
For URV below reference point (30 psi), effect equals:


 30 psi 

 span psi 
± 0.15 + 0.15
Stability
2 bar 
 in % of span
bar 

 span
±0.1625% of span.
For URV below reference point (30 psi), effect equals:
± 0.0125 + 0.15
Combined Zero and Span Static
Pressure Effect per 1000 psi (70
bar)


or ± 0.075 + 0.15



2 bar 
 in % of span
 span bar 
or ± 0.15 + 0.15

±0.04% of URL per year
* Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
6
ST 3000 Smart Pressure Transmitter
Performance Under Rated Conditions* - Model STD974 (0 to 3,000 psi/210 bar)
Parameter
Description
Upper Range Limit
psi
bar
3,000
210
Minimum Span
psi
bar
30
2.1
Turndown Ratio
100 to 1
Zero Elevation and Suppression
–0.6 and +100% URL.
In Analog Mode: ±0.2% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (300 psi), accuracy equals:
Accuracy (Reference – Includes
combined effects of linearity,
hysteresis, and repeatability)
• Accuracy includes residual error
after averaging successive
readings.
• For FOUNDATIONTM Fieldbus use
Digital Mode specifications.
• For HART® use Analog Mode
specifications.


 300 psi 

 span psi 
± 0.05 + 0.15
21 bar 
 in % of span
bar 

 span
In Digital Mode: ±0.175% of calibrated span or upper range value (URV), whichever is
greater, terminal based.
For URV below reference point (300 psi), accuracy equals:


 300 psi 

 span psi 
± 0.025 + 0.15
Zero Temperature Effect per
28°C (50°F)


or ± 0.05 + 0.15



or ± 0.025 + 0.15

21 bar 
 in % of span
bar 

 span
In Analog Mode: ±0.2125% of span.
For URV below reference point (500 psi), effect equals:


 500 psi 

 span psi 


 35 bar 

 span bar 
or ± 0.0125 + 0.20
± 0.0125 + 0.20
in % of span
In Digital Mode: ±0.20% of span.
For URV below reference point (500 psi), effect equals:
 500 psi 

 span psi 
± 0.20
Combined Zero and Span
Temperature Effect per 28°C
(50°F)
 35 bar 

 span bar 
or ± 0.20
in % of span
In Analog Mode: ±0.325% of span.
For URV below reference point (500 psi), effect equals:


 500 psi 

 span psi 
± 0.0125 + 0.20


 35 bar 

 span bar 
or ± 0.0125 + 0.20
in % of span
In Digital Mode: ±0.30% of span.
For URV below reference point (500 psi), effect equals:


 500 psi 

 span psi 
± 0.10 + 0.20
Zero Static Pressure Effect per
1,000 psi (70 bar)


 500 psi 

 span psi 
in % of span


or ± 0.0125 + 0.15

35 bar 

bar 

 span
±0.30% of span.
For URV below reference point (500 psi), effect equals:


 500 psi 

 span psi 
± 0.15 + 0.15
Stability
 35 bar 

 span bar 
±0.1625% of span.
For URV below reference point (500 psi), effect equals:
± 0.0125 + 0.15
Combined Zero and Span Static
Pressure Effect per 1,000 psi (70
bar)


or ± 0.10 + 0.20


35 bar 
 in % of span
 span bar 
or ± 0.15 + 0.15

±0.03% of URL per year
* Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, 10 to 55% RH, and
316L Stainless Steel barrier diaphragm.
ST 3000 Smart Pressure Transmitter
7
Performance Under Rated Conditions - General for all Models
Parameter
Description
Output (two-wire)
Analog 4 to 20 mA or DE digital communications mode. Options available for
FOUNDATIONTM Fieldbus and HART® protocol.
Supply Voltage Effect
0.005% span per volt.
Damping Time Constant
Adjustable from 0 to 32 seconds digital damping.
CE Conformity (Europe)
89/336/EEC, Electromagnetic Compatibility (EMC) Directive.
NAMUR NE 43 Compliance
Option
Transmitter failure information is generated when the measuring information is invalid
or no longer present. Failure information is transmitted as a current signal but
outside the normal 4-20 mA measurement signal level. Transmitter failure values
are: ≤ 3.6 mA and ≥ 21.0 mA. The normal signal range is ≥ 3.8 mA and ≤ 20.5 mA.
SIL 2/3 Compliance
SIL certified to IEC 61508 for non-redundant use in SIL 2 related Safety Systems
(single use) and for redundant (multiple) use in SIL 3 Safety Systems through
TÜV Nord Sys Tec GmbH & Co. KG under the following standards:
IEC61508-1: 1998; IEC 61508-2: 2000; IEC61508-3: 1998.
Lightning Protection Option
(Code “LP”)
Leakage Current: 10 microamps max. @ 42.4 VDC, 93°C
Impulse Rating: 10/20 µ sec.
5,000 Amps (50 strikes)
strikes)
(rise/decay)
10/1,000 µ sec. 250 Amps (1,000 strikes)
10,000 Amps (20
500 Amps (400 strikes)
Physical and Approval Bodies
Parameter
Description
Barrier Diaphragms Material
STD924, STD930, STD974
316L SS, Hastelloy C-276 , Monel 400 , Tantalum, Gold plated 316LSS, Gold plated Hastelloy
2
®
3
C-276 , Gold plated Monel 400
Process Head Material
STD924, STD930, STD974
316 SS , Carbon Steel (zinc-plated) , Monel 400 , Hastelloy C-276
®
2
®
4
3
5
®
3
4
5
6
7
7
®
6
®
Head Gaskets
Glass filled PTFE standard. Viton and graphite optional.
Meter Body Bolting
Carbon Steel (Zinc plated) standard. Options include 316 SS, NACE A286 SS bolts with NACE
304 SS nuts, and B7M.
5
4
2
®
®
6
®
7
Optional Adapter Flange and Bolts
Adapter Flange materials include 316 SS , Hastelloy C-276 and Monel 400 . Options for bolting
4
include carbon steel, 316SS , NACE A286SS and B7M. Standard adapter flange gasket material
®
is glass filled PTFE. Viton and graphite optional.
Mounting Bracket
Carbon Steel (Zinc-plated) or Stainless Steel angle bracket or Carbon Steel flat bracket available
(standard options).
Fill Fluid
Silicone DC 200 oil or CTFE (Chlorotrifluoroethylene)
Electronic Housing
Epoxy-Polyester hybrid paint. Low Copper-Aluminum. Meets NEMA 4X (watertight) and NEMA 7
(explosionproof). Stainless steel optional.
Process Connections
1/4-inch NPT; 1/2-inch NPT with adapter. Process heads meet DIN 19,213 requirements.
Wiring
Accepts up to 16 AWG (1.5 mm diameter).
Mounting
Can be mounted in virtually any position using the standard mounting bracket. Bracket is
designed to mount on 2-inch (50 mm) vertical or horizontal pipe. See Figure 3.
Dimensions
See Figure 4.
Net Weight
Approximately 9 pounds (4.1 Kg).
®
Hastelloy® C-276 or UNS N10276
Monel® 400 or UNS N04400
Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.
Carbon Steel heads are zinc-plated and not recommended for water service due to hydrogen migration. For that service, use 316 stainless steel wetted
Process Heads.
Hastelloy® C-276 or UNS N10276. Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
Monel® 400 or UNS N04400. Supplied as indicated or as Grade M30C, the casting equivalent of Monel® 400
Note: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or vessel(s) from
exceeding allowable pressure limits, (equipment with safety functions in accordance with Pressure Equipment Directive
97/23/EC article 1, 2.1.3), require separate examination
8
ST 3000 Smart Pressure Transmitter
Certifications
Type of Protection
Comm. Option
Explosionproof:
Class I, Division 1, Groups A, B, C, D
locations
Dust Ignition Proof:
Class II, III, Division 1, Groups E, F, G
locations,
Enclosure Type 4X
Intrinsically Safe:
Class I, II, III, Division 1, Groups A, B,
C, D, E, F, G locations, Enclosure Type
4X
All
FM
ApprovalsSM
T4 Ta = 93ºC
4-20 mA /
Vmax = 30V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FISCO)
Vmax = 32V
Imax = 120mA
Ci = 4.2nF
Li = 0
Pi =0.84W
T4 Ta = 40ºC
T3 Ta = 93ºC
Fieldbus – Entity
(Not FISCO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
FISCO
Vmax = 17.5V
Imax = 380mA
Ci = 4.2nF
Li = 0
Pi =5.32W
T4 Ta = 40ºC
T3 Ta = 93ºC
4-20 mA / DE
Vmax = 42.4V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
4-20 mA / HART
Vmax = 30V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FNICO)
Vmax = 32V
Imax = 120mA
Ci = 4.2nF
Li = 0
Pi =0.84W
T4 Ta = 40ºC
T3 Ta = 93ºC
Fieldbus – Entity
(Not FNICO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
Vmax = 32V
Ci = 4.2nF
Li = 0
T4 Ta = 40ºC
T3 Ta = 93ºC
Nonincendive:
Class I, Division 2, Groups A, B, C, D
locations, Enclosure Type 4X
Class I, Division 2, Groups A, B, C, D;
Suitable for:
Class II, Division 2, Groups F&G;
Class III, Division 2;
Class I, Zone 2, Group IIC,
Enclosure Type 4X / IP 66/67
FNICO
*Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
FM ApprovalsSM is a service mark of FM Global
T5 Ta = 93ºC
4-20 mA / DE
Class 1, Zone 0, AEx ia Group IIC,
Enclosure Type 4X / IP 66/67
Nonincendive:
All
Temp. Codes
Vmax = 42.4V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
Intrinsically Safe:
Class I, II, III, Division 1, Groups A, B,
C, D, E, F, G locations;
Field
Parameters
ST 3000 Smart Pressure Transmitter
Type of Protection
Explosion Proof: Class I, Division
1, Groups B, C, D locations
Dust Ignition Proof: Class II, III,
Division 1, Groups E, F, G
locations,
Enclosure Type 4X
9
Comm. Option
All
Canadian
Standards
Association
(CSA)
Canadian Registration Number
(CRN):
T4 Ta = 93ºC
4-20 mA / DE
T4 Ta = 93ºC
4-20 mA / HART
Vmax = 42V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FISCO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
4-20 mA / DE
Vmax = 42.4V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
4-20 mA / HART
Vmax = 30V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = 93ºC
Fieldbus – Entity
(Not FNICO)
Vmax = 24V
Imax = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = 40ºC
T3 Ta = 93ºC
Nonincendive:
Class I, Division 2, Groups A, B, C,
D locations, Enclosure Type 4X
All
Temp. Codes
Vmax = 42V
Imax = 225mA
Ci = 4.2nF
Li = *
Pi =1.2W
Intrinsically Safe:
Class I, II, III, Division 1, Groups A,
B, C, D, E, F, G locations,
Enclosure Type 4X
Field Parameters
All ST 3000 models except STG19L, STG99L, STG170 and STG180
have been registered in all provinces and territories in Canada and are
marked CRN: 0F8914.5C.
10
ST 3000 Smart Pressure Transmitter
Type of Protection
Comm. Option
Field Parameters
Flameproof, Zone 1:
All
All
Ex d IIC, Enclosure IP 66/67
IECEx
International
Electrotechnical
Commission
(LCIE)
Temp. Codes
T5 Ta = –50 to 93ºC
T6 Ta = –50 to 78ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
Intrinsically Safe, Zone 0/1:
Ex ia IIC, Enclosure IP 66/67
Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
Type of Protection
Comm. Option
Flameproof, Zone 1:
Ex d IIC, Enclosure IP 66/67
Intrinsically Safe, Zone 0/1:
Ex ia IIC, Enclosure IP 66/67
SAEx
(South Africa)
All
Intrinsically Safe, Zone 0/1:
Ex ia IIC, Enclosure IP 66/67
All
Temp. Codes
T5 Ta = –50 to 93ºC
T6 Ta = –50 to 78ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
Multiple Marking:
Flameproof, Zone 1:
Ex d IIC, Enclosure IP 66/67
Field Parameters
NOTE: The user must determine the
type of protection required for
installation of the equipment. The
user shall then check the box [√]
adjacent to the type of protection used
on the equipment certification
nameplate. Once a type of protection
has been checked on the nameplate,
subsequently the equipment shall not
be reinstalled using any of the other
certification types.
* Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
ST 3000 Smart Pressure Transmitter
Type of Protection
11
Comm. Option
Flameproof, Zone 0:
, Ex tD
Enclosure IP 66/67
Flameproof, Zone 1:
, Ex d IIC, Ex tD
Enclosure IP 66/67
All
A20 IP6X T95ºC Ta = 93ºC
or T80ºC Ta = 78ºC
All
All
T5 Ta = –50 to +93ºC
T6 Ta = –50 to +78ºC,
A21 IP6X T95ºC Ta = 93ºC
or T80ºC Ta = 78ºC
4-20 mA / DE
Enclosure IP 66/67
4-20 mA / HART
Fieldbus
(Not FISCO)
Non-Sparking, Zone 2:
,Ex nA IIC (Honeywell),
Enclosure IP 66/67
4-20 mA / DE
4-20 mA / HART
ATEX
(LCIE)
Fieldbus
(Not FNICO)
Multiple Marking:
Flameproof, Zone 1:
, Ex d IIC
Intrinsically Safe, Zone 0/1:
, Ex ia IIC
4-20 mA / DE
4-20 mA / HART
Non-Sparking, Zone 2:
, Ex nA IIC
NOTE: The user must determine
the type of protection required for
installation of the equipment. The
user shall then check the box [ √ ]
adjacent to the type of protection
used on the equipment certification
nameplate. Once a type of
protection has been checked on the
nameplate, subsequently the
equipment shall not be reinstalled
using any of the other certification
types.
Fieldbus
(Not FISCO/FNICO)
* Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
Temp. Codes
All
Intrinsically Safe, Zone 0/1:
, Ex ia IIC,
Field
Parameters
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
12
ST 3000 Smart Pressure Transmitter
Type of Protection
Comm. Option
Field Parameters
Temp. Codes
All
All
T5 Ta = –50 to 93ºC
T6 Ta = –50 to 78ºC
Flameproof, Zone 1:
BR-Ex d IIC
Enclosure IP 66/67
INMETRO
(CERTUSP)
Brazil
4-20 mA / DE
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 85ºC
T6 Ta = –50 to 70ºC
4-20 mA / HART
Ui = 30V
Ii = 100mA
Ci = 4.2nF
Li = *
Pi =1.2W
T4 Ta = –50 to 93ºC
T5 Ta = –50 to 63ºC
T6 Ta = –50 to 48ºC
Fieldbus
(Not FISCO)
Ui = 24V
Ii = 250mA
Ci = 4.2nF
Li = 0
Pi =1.2W
T3 Ta = –50 to 93ºC
T4 Ta = –50 to 40ºC
Intrinsically Safe, Zone 0/1:
BR-Ex ia IIC
Enclosure IP 66/67
* Li = 0 except Li = 150µH when Option ME, Analog Meter, is selected.
This certificate defines the certifications covered for the ST 3000 Pressure Transmitter family of
products, including the SMV 3000 Smart Multivariable Transmitter. It represents the compilation of
the five certificates Honeywell currently has covering the certification of these products into marine
applications.
For ST 3000 Smart Pressure Transmitter and SMV 3000 Smart Multivarible Transmitter
American Bureau of Shipping (ABS) - 2009 Steel Vessel Rules 1-1-4/3.7, 4-6-2/5.15, 4-8-3/13 &
ST 3000 Pressure
13.5, 4-8-4/27.5.1, 4-9-7/13. Certificate number: 04-HS417416-PDA
Transmitter Marine
Certificate
Bureau Veritas (BV) - Product Code: 389:1H. Certificate number: 12660/B0 BV
(MT Option)
Det Norske Veritas (DNV) - Location Classes: Temperature D, Humidity B, Vibration A, EMC B,
Enclosure C. For salt spray exposure; enclosure of 316 SST or 2-part epoxy protection with 316
SST bolts to be applied. Certificate number: A-11476
Korean Register of Shipping (KR) - Certificate number: LOX17743-AE001
Lloyd's Register (LR) - Certificate number: 02/60001(E1) & (E2)
ST 3000 Smart Pressure Transmitter
13
The ST 3000 Smart Pressure Transmitters are in conformity with the essential requirements of the Pressure
Equipment Directive.
European
Pressure
Equipment
Directive (PED)
(97/23/EC)
Honeywell ST 3000 Smart Pressure Transmitters are designed and manufactured in accordance with the
applicable portions of Annex I, Essential Safety Requirements, and sound engineering practices. These
transmitters have no pressurized internal volume, or have a pressurized internal volume rated less than 200 bar
(2,900 psig), and/or have a maximum volume of less than 0.1 liter (Article 3, 1.1.(a) first indent, Group 1 fluids).
Therefore, these transmitters are not subject to the essential requirements of the directive 97/23/EC (PED,
Annex I) and shall not have the CE mark applied.
For transmitters rated > 200 bar (2,900 psig) < 1,000 bar (14,500 psig) Honeywell maintains a technical file in
accordance with Annex III, Module A, (internal production control) when the CE mark is required. Transmitter
Attachments: Diaphragm Seals, Process Flanges and Manifolds comply with Sound Engineering Practice.
NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or
vessel(s) from exceeding allowable pressure limits, (equipment with safety functions in accordance with
Pressure Equipment Directive 97/23/EC article 1, 2.1.3), require separate examination.
A formal statement from TÜV Industry Service Group of TÜV America, Inc., a division of TÜV Süddeutschland,
a Notified Body regarding the Pressure Equipment Directive, can be found at www.honeywell.com. A hard
copy may be obtained by contacting a Honeywell representative.
CE Mark
Dual Seal
Certification
Electro Magnetic Compatibility (EMC) (2004/108/EC)
All Models: EN 50081-1: 1992; EN 50082-2:1995; EN 61326-1:1997 + A1, A2, and A3 – Industrial Locations
Dual Seal Certification based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.01 requirements without the use of
additional seal protection elements.
Recommended
Frequency of
Calibration
Honeywell recommends verifying the calibration of these devices once every four years.
Approved
Manufacturing
Locations
Honeywell Process Solutions - York, PA USA
Honeywell (Tianjin) Limited – Tianjin, P.R. China
Honeywell Automation India Ltd. – Pune 411013 India
FoundationTM Fieldbus is a trademark of the Fieldbus Foundation.
Viton® is a registered trademark of DuPont
Teflon® is a registered trademark of DuPont.
HART® is a registered trademark of HART Communications Foundation.
DC® 200 is a registered trademark of Dow Corning.
Hastelloy® C-276 is a registered trademark of Haynes International.
FM ApprovalsSM is a service mark of FM Global
Monel® 400 is a registered trademark of Special Metals Corporation.
ST 3000 and Experion are registered trademarks of Honeywell International Inc.
14
ST 3000 Smart Pressure Transmitter
Mounting
Figure 3 – Examples of typical mounting positions for Models STD924, STD930 and STD974
Figure 4 – Typical mounting dimensions of STD924, STD930 and STD974 for reference
ST 3000 Smart Pressure Transmitter
15
Options
•
•
Mounting Bracket (Options MB, MX, SB, SX, FB)
This option provides software the meets the NAMUR
plated carbon steel or stainless steel and is suitable for
NE43 requirements for failsafe software. Transmitter
horizontal or vertical mounting on a two inch (50
failure information is generated when the measuring
millimeter) pipe, as well as wall mounting. An optional
information is no longer valid.
flat mounting bracket is also available in carbon steel
Transmitter failure values are ≤ 3.6 mA and ≥ 21.0 mA.
for two inch (50 millimeter) pipe mounting.
The normal ST 3000 ranges are ≤ 3.8 mA and ≥ 20.8
Indicating Meter (Options ME and SM)
mA.
Two integral meter options are available. An analog
meter (option ME) is available with a 0 to 100% linear
scale. The Smart Meter (option SM) provides an LCD
display for both analog and digital output and can be
configured to display pressure in pre-selected
engineering units.
•
• Stainless Steel Tagging (Option TG)
Up to 30 characters can be added on the stainless steel
nameplate mounted on the transmitter’s electronics
housing at no extra cost. A stainless steel wired on tag
with additional data of up to 4 lines of 28 characters is
also available. The number of characters for tagging
the transmitter from transient surges induced by nearby
includes spaces.
• Transmitter Configuration (Options TC and FC)
HART® Protocol Compatibility
With Option TC, the factory can configure the analog,
(Options HC and H6)
DE or HART® transmitter’s linear/square root extraction,
Optional electronics modules for the ST 3000 that
damping time, LRV, URV and mode (analog/digital) and
provides HART protocol compatibility in either the
enter an ID tag of up to eight characters and scratchpad
HART 5.x or 6.x formats. Transmitters with a HART
information as specified.
that provides either 5.x or 6.x format support.
FOUNDATION Fieldbus (Option FF)
Equips transmitter with FF protocol for use in 31.25
kbit/s FF networks. See document 34-ST-03-72 for
additional information on ST 3000 Fieldbus transmitters.
•
Provides custom configuration of Smart Meters
A terminal block is available with circuitry that protects
option are compatible with any HART enabled system
•
• Indicator Configuration (Option CI)
Lightning Protection (Option LP)
lightning strikes.
•
• NAMUR NE43 Compliance (Option NE)
The angle mounting bracket is available in either zinc-
SIL2/SIL3 Certification (Option SL)
This ST 3000 product is available for use with safety
systems. With the SL option, we are fully certified to
SIL 2 capability for single transmitters and SIL 3
capability for multiple transmitter use through TÜV Nord
Sys Tec GmbH & Co. KG. We are in compliance with
the following SIL standards:
IEC 61508-1: 1998;
IEC 61508-2: 2000;
IEC 61508-3: 1998.
With Option FC, the Device ID, Transmitter Tag, Unit
Level Node Address, Output Mode and Damping Time
Constants can be specified.
• Custom Calibration and ID in Memory (Option CC)
The factory can calibrate any range within the scope of
the transmitter’s range and enter an ID tag of up to
eight characters in the transmitter’s memory.
16
ST 3000 Smart Pressure Transmitter
Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Prior to specifying or ordering a model check for the latest revision Model Selection Guides which are published at:
http://hpsweb.honeywell.com/Cultures/en-US/Products/Instrumentation/ProductModelSelectionGuides/default.htm
Model Selection Guide
ST 3000 Smart Transmitter
Differential Pressure (DP)
Series 900
Model Selection Guide
34-ST-16U-24
Issue 55
Page 1 of 5
Instructions
●
●
●
●
●
Select the desired Key Number. The arrow to the right marks the selection available.
Make one selection from each Table (I, II and IV), using the column below the proper arrow.
Select as many Table III options as desired plus a communications option selection.
A (●) denotes unrestricted availability. A letter denotes restricted availability.
Restrictions follow Table IV.
Key Number
______
I
-
II
___
-
III (Optional)
00000
_ _, _ _, _ _
-
IV
XXXX
+
KEY NUMBER
Span
0-4" to 0-400" H2O / 0-10 to 0-1,000 mbar
Body Rating: 4,500 psi (310 bar)
0-1 to 0-100 psi / 0-0.07 to 0-7 bar
Body Rating: 4,500 psi (310 bar)
0-30 to 0-3,000 psi / 0-2.1 to 0-210 bar
Body Rating: 4,500 psi (310 bar)
Important Note:
Selection
Availability
STD924
STD930
STD974
Base STD models no longer include a default communications option. All units now require the
selection of a communication option from Table III (AN, DE, HC, H6 or FF).
TABLE I - METER BODY
Process Wetted
Heads
1
Materials of
Construction
Fill Fluid
Process Head
Configuration
TABLE II
No Selection
1
2
3
4
5
6
7
9
Carbon Steel
1
Carbon Steel
1
Carbon Steel
1
Carbon Steel
5
316 SS
5
316 SS
5
316 SS
5
316 SS
®
3, 6
Hastelloy C
®
3, 6
Hastelloy C
® 4, 7
Monel 400
Vent/Drain
Valves
Barrier Diaphragms
Selection
316L SS
A__
B__
C__
D__
E__
F__
G__
H__
J__
K__
L__
_1_
_2_
__A
__H
2
and Plugs
316 SS
316 SS
316 SS
316 SS
316 SS
316 SS
316 SS
316 SS
®
®
Hastelloy C-276
®4
Monel 400
Tantalum
316L SS
®
Hastelloy C-276
®4
Monel 400
Tantalum
3
®
Hastelloy C-276
Hastelloy C-276
®
3
Tantalum
Hastelloy C-276
®9
®4
Monel 400
Monel 400
®
DC 200 Silicone
CTFE
1/4 NPT
1/2 NPT with Adapter (on 1/4 NPT Head)
3
3
3
Selection
00000
●
●
●
●
●
●
19
19
19
●
●
●
●
●
●
●
●
●
19
19
19
●
●
●
●
●
●
●
●
●
19
19
19
●
●
●
t
●
●
●
t
●
●
●
t
●
●
●
Carbon Steel heads are zinc-plated and not recommended for water service due to hydrogen migration. For that service, use
316 stainless steel wetted Process Heads.
Vent/Drains are sealed with Teflon® or PTFE.
Hastelloy® C-276 or UNS N10276
Monel 400® or UNS N04400
Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.
Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
Supplied as indicated or as Grade M30C the casting equivalent of Monel 400®
Monel 400® or UNS N04400 or UNS N04405
ST 3000 Smart Pressure Transmitter
34-ST-16U-24
Issue 55
Page 2 of 5
Availability
STD9xx
TABLE III - OPTIONS
Communication Options (Must choose a communications option)
Analog only (can be configured using appropriate Honeywell DE tool)
DE Protocol communications
®
HART 6.x Protocol Compatible Electronics
FOUNDATIONTM Fieldbus Communications
Indicating Meter Options
Analog Meter (0-100 Even 0-10 Square Root)
Smart Meter
Custom Configuration of Smart Meter
Local Zero
Local Zero and Span
Transmitter Housing & Electronics Options
No housing conduit plugs or adaptors come standard with the ST 3000.
For certain approval codes, you must select a certified conduit plug from below and it
will come packaged in the box with your transmitter.
5
316 SS Electronics Housing - (with M20 conduit connections)
5
316 SS Electronics Housing - (with M20 to 1/2 NPT 316 SS conduit adaptor for use with
FM and CSA Approval codes)
1/2 NPT Male to M20 Female 316 SS Certified Conduit Adapter ( ATEX, CSA & IECEx)
1/2 NPT Male to 3/4 NPT Female 316 SS Certified Conduit Adapter (ATEX, CSA &
IECEx)
M20 Male to 1/2 NPT Female 316 SS Certified Conduit Adaptor (ATEX, CSA & IECEx)
1/2 NPT Zinc-plated Certified Conduit Plug (ATEX, CSA & IECEx)
1/2 NPT 316 SS Certified Conduit Plug (ATEX, CSA & IECEx)
M20 316 SS Certified Conduit Plug (ATEX, CSA & IECEx)
1/2 NPT Non-certified Conduit plug (Zinc-plated carbon steel, general use)
NAMUR Failsafe Software
SIL 2 - TÜV Certified transmitter (requires HC/H6 and WP options)
Lightning Protection
Custom Calibration and I.D. in Memory
Transmitter Configuration - (non-Fieldbus)
Transmitter Configuration - (Fieldbus)
Write Protection (Delivered in the "enabled" position)
Write Protection (Delivered in the "disabled" position)
Stainless Steel Customer Wired-On Tag (4 lines, 26 characters per line, customer
supplied information)
Stainless Steel Customer Wired-On Tag (blank)
o
Low Temperature (-50 C Ambient Limit)
Meter Body Options (Seal bolt material depends on Transmitter bolt material)
316 SS Bolts and 316 SS Nuts for Process Heads
B7M Bolts and Nuts for Process Heads
NACE A286 SS Bolts and NACE 304 SS Nuts for Process Heads
5
316 SS Adapter Flange - 1/2 NPT with CS Bolts
5
316 SS Adapter Flange - 1/2 NPT with 316 SS Bolts
5
316 SS Adapter Flange - 1/2 NPT with NACE A286 SS Bolts
5
316 SS Adapter Flange - 1/2 NPT with B7M Bolts
®
3, 6
Adapter Flange - 1/2 NPT with CS Bolts
Hastelloy C-276
®
3, 6
Adapter Flange - 1/2 NPT with 316 SS Bolts
Hastelloy C-276
® 4, 7
Adapter Flange - 1/2 NPT with CS Bolts
Monel 400
® 4, 7
Adapter Flange - 1/2 NPT with 316 SS Bolts
Monel 400
5
316 SS Blind Adapter Flange with CS Bolts
5
316 SS Blind Adapter Flange with 316 SS Bolts
5
316 SS Blind Adapter Flange with NACE A286 SS Bolts
5
316 SS Blind Adapter Flange with B7M Bolts
Side Vent/Drain (End Vent Drain is standard)
316 SS Center Vent Drain and Bushing
®8
Viton Process Head Gaskets (adapter gaskets ordered separately)
Graphite Process Head & Adapter Flange Gaskets
3
4
5
6
7
8
Viton
®8
17
Adapter Flange Gaskets
Hastelloy® C-276 or UNS N10276
Monel 400® or UNS N04400
Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.
Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
Supplied as indicated or as Grade M30C, the casting equivalent of Monel 400®
Viton® or Fluorocarbon Elastomer
Selection 24 30
74
AN
DE
H6
FF
●
●
●
r
●
●
●
r
●
●
●
r
ME
SM
CI
LZ
ZS
●
●
e
x
m
●
●
e
x
m
●
●
e
x
m
SH
n
n
n
A3
i
i
i
A1
●
●
●
A2
●
●
●
A4
A5
A6
A7
A8
NE
SL
LP
CC
TC
FC
WP
WX
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
15
15
15
p
●
●
p
●
●
p
●
●
15
21
15
21
15
21
b
●
●
●
●
●
●
b
TG
●
●
●
TB
LT
●
●
●
18
●
●
●
c
c
c
c
c
c
c
c
●
●
●
●
●
●
●
●
●
●
●
c
c
c
c
c
c
c
c
●
●
●
●
●
●
●
●
●
●
●
c
c
c
c
c
c
c
c
●
●
●
●
●
●
●
●
17
17
17
SS
B7
CR
S2
S3
S4
S5
T2
T3
V2
V3
B3
B4
B5
B6
SV
CV
VT
GF
VF
b
b
b
b
b
b
b
b
18
ST 3000 Smart Pressure Transmitter
34-ST-16U-24
Issue 55
Page 3 of 5
Availability
STD9xx
TABLE III - OPTIONS (continued)
Transmitter Mounting Bracket Options
Angle Mounting Bracket - Carbon Steel
Marine Approved Angle Mounting Bracket - Carbon Steel
Angle Mounting Bracket - 304 SS
Marine Approved Angle Mounting Bracket - 304 SS
Flat Mounting Bracket (pipe mounting) - Carbon Steel
Diaphragm Options
Gold plated diaphragm(s) on 316 SS
®4
®
3
Gold plated diaphragm(s) on Monel 400 or Hastelloy C-276 ONLY
Services/Certificates/Marine Type Approvals Options
User's Manual Paper Copy (Standard, HC, H6 or FF ships accordingly)
Clean Transmitter for Oxygen or Chlorine Service with Certificate (50039190)
Over-Pressure Leak Test with Certificate ( F3392 )
Calibration Test Report and Certificate of Conformance (F3399)
Certificate of Conformance (F3391)
Certificate of Origin (F0195)
SIL Certificate (SIL 2/3) (FC33337)
NACE Certificate (Process-Wetted & Non-Process Wetted) (FC33339)
NACE Certificate (Process-Wetted) (FC33338)
Material Traceability Certification per EN 10204 3.1 (FC33341)
Marine Type Approvals (DNV, ABS, BV, KR & LR) (FC33340)
Selection
24
30
74
MB
MX
SB
SX
FB
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
b
G1
G2
●
●
●
●
●
●
b
UM
0X
TP
F1
F3
F5
FE
F7
FG
FX
MT
●
j
●
●
●
●
●
j
●
●
●
●
●
j
●
●
●
●
22
22
22
o
●
●
o
●
●
o
●
●
2
2
2
●
●
●
●
●
●
●
●
●
●
●
●
Selection
24
30
74
9X
●
●
●
1C
●
●
●
2J
24 24
f
b
b
Warranty Options
Additional Warranty - 1 year
Additional Warranty - 2 years
Additional Warranty - 3 years
Additional Warranty - 4 years
W1
W2
W3
W4
b
STD9xx
restriction "f",
Approval
Approval Type
Body
No hazardous location approvals
Explosion Proof
FM
Dust-Ignitionproof
SM
Approvals
Non-Incendive
Intrinsically Safe
Canadian
Explosion Proof
Standards
Association
(CSA)
IECEx
Class I, Div. 1, Groups A,B,C,D
Class II, III Div. 1, Groups E,F,G
Class I, Div. 2, Groups A,B,C,D
Class I, II, III, Div. 1, Groups A,B,C,D,E,F,G
Class I, Div. 1, Groups B,C,D
Dust-Ignitionproof
Class II, III, Div. 1, Groups E,F,G
Intrinsically Safe
Class I, II, III, Div. 1, Groups A,B,C,D,E,F,G
Flameproof,
Zone 1
Ex d IIC
T5 (Ta = -40 to +93ºC),
T6 (Ta = -40 to +78ºC)
Ex ia IIC; T3, T4, T5 , T6
Intrinsically Safe,
Zone 0/1
CERTUSP
INMETRO
(Brazil)
Location or Classification
Flameproof, Zone 1
Intrinsically Safe,
Zone 0/1
b
CA
24 24 24
6D
●
●
●
6S
●
●
●
See Spec for detailed
temperature codes by Communications option
BR- Ex d IIC; T5, T6
BR- Ex ia IIC; T4, T5, T6
(See CERTUSP certificate for detailed temperature
codes by Communications option)
Table III Approvals continued next page
3
4
Hastelloy® C-276 or UNS N10276
Monel 400® or UNS N04400
ST 3000 Smart Pressure Transmitter
19
34-ST-16U-24
Issue 55
Page 4 of 5
STD9xx
TABLE III - OPTIONS (continued)
Approval
Approval Type
Body
ATEX 10
(LCIE)
Location or Classification
Intrinsically Safe,
Zone 0
Ex ia IIC
T4 (Ta = –50°C to +93°C);
T5 (Ta = –50°C to +85°C);
T6 (Ta = –50°C to +70°C)
Enclosure IP 66/67
Intrinsically Safe,
Zone 1
Ex ia IIC
T4 (Ta = –50°C to +93°C);
T5 (Ta = –50°C to +85°C);
T6 (Ta = –50°C to +70°C)
Enclosure IP 66/67
Dust-tight Enclosure,
Zone 0
Ex tD A20 IP6X
T95°C (at Ta = 93°C) or
T80°C (at Ta = 78°C)
Enclosure IP 66/67
Flameproof and
Dust-tight Enclosure,
Zone 1
Ex d IIC
T5 (Ta = –40°C to +93°C),
T6 (Ta = –40°C to +78°C)
Supply 11- 42Vdc
Ex tD A21 IP6X
T95°C (at Ta = 93°C) or
T80°C (at Ta = 78°C)
Enclosure IP 66/67
Non-Sparking,
Zone 2
Ex nA, IIC
T5 (Ta = –40°C to +93°C),
T6 (Ta = –40°C to +78°C);
Zone 2 Supply < 42Vdc, 23mA
Ex tD A22 IP6X
T95°C (at Ta = 93°C) or
T80°C (at Ta = 78°C) (Honeywell).
Enclosure IP 66/67
Multiple Marking
11
Int. Safe, Zone 0/1 and
Dust-tight Enclosure,
or
Flameproof, Zone 1 and
Dust-tight Enclosure,
or
Non-Sparking, Zone 2
Intrinsically Safe,
Zone 0/1
Flameproof, Zone 1
SAEx
(South Africa) Multiple Marking 11
Selection
24
30
74
3S
●
●
●
33
24 24 24
3N
●
●
●
Ex ia IIC
T4 (Ta = –50°C to +93°C);
T5 (Ta = –50°C to +85°C);
T6 (Ta = –50°C to +70°C);
Ui = 30V; Ii = 100mA
Ex tD A20 IP6X
T95°C (at Ta = 93°C) or
T80°C (at Ta = 78°C)
Ex d IIC
T5 (Ta = –40°C to +93°C),
T6 (Ta = –40°C to +78°C)
Supply 11- 42Vdc
Ex tD A21 IP6X
T95°C (at Ta = 93°C) or
T80°C (at Ta = 78°C)
b
3C
24 24 24
Z2
●
●
●
ZD
●
●
●
●
●
Ex nA, IIC
T5 (Ta = –40°C to +93°C),
T6 (Ta = –40°C to +78°C);
Zone 2 Supply < 42Vdc, 23mA
Ex tD A22 IP6X
T95°C (at Ta = 93°C) or
T80°C (at Ta = 78°C) (Honeywell)
Enclosure IP 66/67
Ex ia IIC T4, T5, T6
Ex d IIC T5, T6
Enclosure IP 66/67
ZA
●
Int. Safe, Zone 0/1, or Ex ia IIC T4, T5, T6
Flameproof, Zone 1 Ex d IIC T5, T6
Enclosure IP 66/67
3
Hastelloy® C-276 or UNS N10276
4
Monel 400® or UNS N04400
10
See ATEX installation requirements in the ST 3000 User's Manual
11
The user must determine the type of protection required for installation of the equipment. The user shall then check the box
[√] adjacent to the type of protection used on the equipment certification nameplate. Once a type of protection has been
checked on the nameplate, subsequently the equipment shall not be reinstalled using any of the other certification types.
20
ST 3000 Smart Pressure Transmitter
34-ST-16U-24
Issue 55
Page 5 of 5
STD9xx
TABLE IV
Factory Identification
Selection
XXXX
24
30
74
●
●
●
RESTRICTIONS
Restriction
Letter
b
c
e
Table
I
III
Not Available With
Available Only With
Selection
Selection
Table
Select only one option from this group
__H
SM
This approval code requires the
L__
selection of a certified conduit plug:
I
A5, A6 or A7
1C or 2J
f
III
i
III
j
m
n
o
p
I
III
III
CR, S4, B5
HC or H6 and WP
r
III
FISCO/FNICO compliance available
only with 1C
t
x
2
15
17
18
19
21
22
III
III
III
S2, S3, S4, S5, T2, T3, V2, V3
FF, SM
MX, SX
III
I
VT
_1_
III
III
FF
SL
24
III
This approval code requires the
selection of a certified conduit plug:
A5, A6 or A7
_2_
Ordering Example:
III
III
ME, FF
1C, 2J
III
FF, 00
III
TC, ME or FISCO/FNICO
compliance not available with 3C, 3N,
33, 3S, 2J, CA, Z2, ZD, ZA, 6D & 6S
III
III
FB, MB, SB
FF
III
F7, FG
STD924-A1A-00000-HC,WP,1C+XXXX
Hastelloy® is a registered trademark of Haynes International
Monel 400® is a registered trademark of Special Metals Corporation.
HART® is a registered trademark of HART Communication Foundation.
FOUNDATIONTM Fieldbus is a trademark of Fieldbus Foundation.
Viton® is a registered trademark of DuPont Performance Elastomers.
Teflon® is a registered trademark of DuPont.
FM ApprovalsSM is a service mark of FM Global
DC® 200 is a registered trademark of Dow Corning
ST 3000 Smart Pressure Transmitter
21
Sales and Service
For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor, contact one
of the offices below.
ASIA PACIFIC
EMEA
NORTH AMERICA
SOUTH AMERICA
(TAC) [email protected]
Phone: + 80012026455 or +44
(0)1202645583
FAX: +44 (0) 1344 655554
Email: (Sales) [email protected]
or
(TAC) [email protected]
Honeywell Process Solutions,
Phone: 1-800-423-9883
Or 1-800-343-0228
Email: (Sales) [email protected] or
(TAC) [email protected]
Honeywell do Brazil & Cia
Phone: +(55-11) 7266-1900
FAX: +(55-11) 7266-1905
Email: (Sales) [email protected] or
(TAC) [email protected]
Australia
Honeywell Limited
Phone: +(61) 7-3846 1255
FAX: +(61) 7-3840 6481
Toll Free 1300-36-39-36
Toll Free Fax:
1300-36-04-70
China – PRC - Shanghai
Honeywell China Inc.
Phone: (86-21) 5257-4568
Fax: (86-21) 6237-2826
Singapore
Honeywell Pte Ltd.
Phone: +(65) 6580 3278
Fax: +(65) 6445-3033
South Korea
Honeywell Korea Co Ltd
Phone: +(822) 799 6114
Fax: +(822) 792 9015
Specifications are subject to change without notice.
22
ST 3000 Smart Pressure Transmitter
For More Information
Learn more about how Honeywell’s ST 3000 Smart
Pressure Transmitters can increase performance, reduce
downtime and decrease configuration costs, visit our
website www.honeywellprocess.com/pressure-transmitters
or contact your Honeywell account manager.
Honeywell Process Solutions
1860 West Rose Garden Lane
Phoenix, AZ 85027
Tel: 1-800-423-9883 or 1-800-343-0228
www.honeywellprocess.com
34-ST-03-65
January 2013
© 2013 Honeywell International Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement