Infinity OMNI-Plus B2382TIR
Infinity OMNI-Plus B2382TIR
User Manual Version #2:
Camera with ICON Menu
11192010
PRECAUTIONS














Do not open or modify.
Do not open the case except during maintenance and installation, for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to Provide reasonable protection against harmful interference .when the equipment is operated in a residential environment. This equipment
generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance
with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacture.
TROUBSHOOTING
Before sending your camera for repair, check the following or contact our technical specialist.
No VIDEO
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus VIDEO
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
FEATURES
1/3” Sony Super HAD II CCD
High Resolution 560TV Lines
OMNI-Focus 2.9~8.5mm 3X Motorized Zoom, Auto Iris
70ft Range IR with Intelligent Camera Sync
True Day & Night / TDN5 (Electro Magnetic Mechanism)
Max-DR (Electronic Wide Dynamic Range)
Enables the camera to capture perfect images in both bright and dark environments simultaneously.
3D-DNR (3D Digital Noise Reduction)
Produces less noise and more color during low-light application.
HME (Highlight Mask Exposure)
Masks overly exposed light to produce a true video image of any environment.
SLC (Side Light Compensation)
DIS (Digital Image Stabilizer)
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
No Fog or Condensation under Any Weather Condition
INSTALLATION AND ADJUSTMENT
Included with DW Bullet Camera:
4
1.
2.
3.
4.
5.
1
5
2
6
7
6.
User Manual
Mounting Template
One Security L-Key
Secondary BNC Cable for a Field Monitor
Four (4) Screws and Four (4) Dry Wall
Anchors
IR Remote Controller
DIMENSION (mm) & POWER REQUIREMENT
RS485 (Black+ / White - )
POWER REQUIREMENT:
12VDC @1A
24VAC @ .500mA
POWER WIRE MAXIMUM DISTANCE
Wire Gauge
24 AWG
22 AWG
20 AWG
18 AWG
16 AWG
14 AWG
12 AWG
10 AWG
12VDC
80feet
128feet
203feet
323feet
514feet
816feet
1295feet
2057feet
24VAC
323feet
513feet
815feet
1295feet
2056feet
3264feet
5183feet
8228feet
COAXIAL CABLE TYPE
MAXIMUM DISTANCE
RG59/ U
RG6/U
RG11/U
750feet
1,000feet
1,500feet
IR REMOTE CONTROLLER
Key Button
Menu Access and Control
1.
2.
Zoom Function
Control
3.
4.
ID Buttons
Motion Alarm ON & OFF
5.
6.
Press [KEY] button + [ID].
(Default is “001” for ID=1.)
Point the remote control towards the camera, then
press and hold [0] until the Red LED light starts
flashing.
Press and hold the [KEY] button, until LED turns a
solid Red color.
Press the [+] button to ZOOM IN, and [-] button to
ZOOM OUT.
Press the [Ent] button to access the Menu and press
[KEY] button to exit.
Press the [9] button to turn the Alarm ON or OFF.
*Note: Turning the Alarm ON disables the zoom function.
CAMERA ON-SCREEN DISPLAY
1.
2.
3.
Functional Control of On-Screen Display [SW1]
Functional of Video Out [CON2]
Functional when using Pan Focus Lens [OPTION]
The LED around the lens flickers 3 times when you push [SW3] for 2 seconds. Then, the function of [SW1] changes from OSD
Control Key to Zooming Control Key.
If you press [SW3] again for 2 seconds, the LED around the lens flickers 3 times. Then, the [SW1] function switches back to
OSD Control Key.
EXPOSURE
LENS
DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER
1/160 /1/100 / FLC / 1/250 ~ 10000 / SENS-UP x2 ~ x250
BLC
OFF / ON
BLC (Back Light Compensation)
AGC
HIGH / MIDDLE / LOW / OFF
AGC (Auto Gain Control)
MAX-DR
OFF / ON (0 ~ 20) (Electronic Wide Dynamic Range)
STAR-LIGHT
AUTO (x2 ~ x250) / OFF (x32 is recommended.)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY RESET
COLOR
WB MODE
AWC / ATW / MANUAL / PUSH LOCK
R-Y GAIN
0 ~ 100
B-Y GAIN
0 ~ 100
DAY & NIGHT
AUTO / COLOR / BW / EX-CONT
Day & Night Mode
COLOR ---- BW : Switching from color to BW; if the number is higher, the camera will only switch during a super low light condition.
BW ---- COLOR : Switching from BW to color; this number should always be lower than COLOR to BW
Read Time: Time interval to switch from Color to Black-and-White
COLOR
B&W: (BURST:OFF/ON) When the burst is OFF will make less noise
C-SUP
Color Suppression :Color will be reduced at low illumination, if the C-SUP Level is higher.
0 ~ 100 (Not Available when DNR is On.)
A-SUP
Aperture Suppression: The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher.
0 ~ 100 (Not Available when DNR is On.)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
FUNCTION
MIRROR
OFF / MIRROR / V-FLIP / ROTATE
SHARPNESS
0 ~ 31
GAMMA
0.05 ~ 1.00 / USER
FREEZE
OFF / ON
NEGATIVE
OFF/ ON
3D-DNR
OFF / LOW / MIDDLE / HIGH
3D-DNR (3D Digital Noise Reduction)
D-ZOOM
OFF / ON (x1.0 ~ x32 PTZ)
SLC
OFF / ON
SLC (Side Light Compensation)
HME
OFF / ON
HME (Highlight Masking Exposure)
DIS
OFF / ON
DIS (Digital Image Stabilizer)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
MOTION
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
M o t i o n A l a r m S etu p
1.
2.
3.
4.
Go to Motion Menu
Set Motion to “ON”
Click [Set Windows] and set your area of the motion detection
Press the Left Arrow button, until you exit back to the Motion Menu
5.
6.
7.
8.
Zoom out to the farthest you want the camera to zoom out and press [7](Wide)
Zoom in to the farthest you want the camera to zoom in and press [8](Tele)
Click [Exit Jump] then click [Save & Exit]
Once you are out of the menu press [9](ON/OFF) to activate motion alarm
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID
0 ~ 255
TITLE
OFF / ON
DPC
OFF / AUTO
DPC (Dead Pixels Cancellation)
MONITOR
CRT / LCD
LANGUAGE
English, Japanese, Chinese
BAUDRATE
2400 / 4800 / 9600 / 14400 / 19200 / 38400.
Protocol is Pelco-D (fixed cannot be changed; hardcoded into the DSP)
OMNI LENS
OFF / 1 ~ 10 (for OMNI-PLUS CAMERA only)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC
INTERNAL / AUTO
V-PHASE
0 ~ 199
EXIT JUMP
EXIT / SAVE & EXIT / FACTORY SET
EXIT
EXIT
Exit the menu
SAVE&EXIT
Exit the menu and save the setting
FACTORY SET
Reset the menu setting to factory default
SPECIFICATIONS:
Camera TYPE
Color / BW
B2382TIR
Mount
3D Bracket
Device
Super HAD II CCD
Size
1/3"
Pixels-Total
811(H) x 508(V)
Pixels-Effective
768(H) x 494(V)
System
525 line, 2:1Interlace
Horizontal Frequency Internal Mode
15,734Hz
Vertical Frequency Internal Mode
59.94Hz
Min. Scene Illumination
IR-LED on
0.0 Lux
Functions
BLC
ON / OFF
AGC
HIGH / MIDDLE / LOW /OFF
MAX-DR
OFF / ON
Mirror
OFF / MIRROR / V-FLIP / ROTATE
STAR-LIGHT
AUTO (x2 ~ x250) / OFF
3D-DNR
OFF / ON
SLC
OFF / ON
HME
OFF / ON
Motion Detection
OFF / ON (Area / Sensitivity)
Privacy Zone
6 Programmable Zone / Size
Lens
Focal Length
OMNI-Focus 2.9~8.5mm 3x Motorized Zoom, Auto Iris
Resolution
Horizontal
560 TV Lines [Color]; 580 TV Lines [BW]
Video Output
VBS 1.0Vp-p
VBS 1.0Vp-p(75 Load)
S/N Ratio
S/N Ratio
50dB
OSD
OSD
YES
Environmental Conditions
Operating Temperature
-10℃ ~ +55℃(14℉ ~ 131℉)
Humidity
Less than 90%
Power Requirement
12VDC / 24VAC
Power Consumption
3.3 [W] / 3.8 [W] LED Off; 6.0 [W] / 6.5 [W] LED On
Image
Scanning
5436 W Crenshaw St. Tampa, FL 33634
Tel: 866-446-3595 / 813-888-9555
Fax: 813-888-9262
www.Digital-Watchdog.com
[email protected]
Technical Support Hours: Monday-Friday
8:30am to 8:00pm Eastern Time
Power
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement