Defender Series Surge + PDU User Manual
Defender Series Surge + PDU User Manual
Congratulations on your SurgeX purchase and thank you for your business. Our Defender Series multi-stage
protection technology will increase server uptime by protecting your equipment from dangerous power events
that can disrupt or even destroy your investment.
Your Defender Series Surge + PDU unit provides:
• Failsafe protection: Shields server equipment from damaging surges, spikes, over
voltage, EMI/RFI noise, and wire faults that can cause downtime, disruption, and
equipment shutdown
• Power distribution: A comprehensive Surge + PDU all-in-one solution
• Redundancy: Extended protection for UPS and ancillary equipment and creates a
stress free environment to keep your system up and running
• Uptime: Helps increase uptime, protect data, extend equipment life and increase
reliability of connected equipment
Our goal is your complete satisfaction. Please visit surgex.com/defenderseries for additional product information,
user manuals, warranty information, and product / warranty registration. Contact us at [email protected] for direct
assistance. Thank you for your purchase!
I.
Product Description
• Power Distribution Unit with multi-stage Surge Protection
• Models:
oSX-DS-L630-FP
• 120/230 VAC Split Phase (North American)
24A Maximum Capacity
15A Maximum Capacity per Bank
(1) NEMA L6-30P
input power cord
(6) IEC-320 C13 output
power receptacles
(2) 15A Branch-Rated
Circuit Breakers
oSX-DS-L530-FP
• 120 VAC Single Phase (North American)
24A Maximum Capacity
15A Maximum Capacity per Bank
(1) NEMA L5-30P input
power cord
(6) IEC-320 C13 output
power receptacles
(2) 15A Branch-Rated
Circuit Breakers
(6) IEC-320 C13 output
power receptacles
(2) 15A Branch-Rated
Circuit Breakers
oSX-DS-520-FP
• 120V Single Phases (North America)
20A Maximum Capacity
10A Maximum Capacity per Bank
(1) NEMA 5-20P input
power cord
© SurgeX
REV-A
Page 1
Defender Series Surge + PDU User Manual
oSX-DS-IEC-FP
• 220-240 VAC Single Phase (International)
32A Maximum Capacity
10A Maximum Capacity per Bank
(1) IEC-60309 332P65 input
power cord
II.
(6) IEC-320 C13 output
power receptacles
(3) 10A Branch Rated
Circuit Breakers
Hardware Included
•
Tower Configuration Hardware – Option A
(1) Base stand
(6) 6/32 x ½” Flathead Screws
• Rack Mount Configuration Hardware – Option B
(1) Left
bracket
(1) Right
bracket
(11) 6/32 x ¼”
Flathead Screws
(4) Thumbscrews
(4) Cage Nuts
• Cable Organizing Hardware (optional)
(1) Cable Organizer
III.
(2) Thumbscrews
(8) Plastic Ties
Installation
•
Warning: Before installing the SurgeX Defender Series unit,
review the safety instructions that came with the unit
Unpack the Unit and Accessories
oIdentify each item; refer to the Quick Start Guide for reference
• Connect Cable Organizing Hardware (Optional)
oUse (2) thumbscrews to attach the cable organizer
to the rear panel (figure 1-a)
• Configure Unit
oSelect Tower or Rack Mount Configuration
•
Determine which configuration is best for your installation
o Option A: For tower installations, the Defender Series
Surge + PDU may be configured to mount upright as a
Tower and can stand on any dry, flat surface
o Option B: For rack installations, the Defender Series
Surge + PDU may be configured to mount within a
standard 19” equipment rack and will require 1 RU (Rack
Unit) of space
1-a
2-a
2-b
o
© SurgeX
REV-A
Page 2
Defender Series Surge + PDU User Manual
o To Install Tower Configuration – Option A
•
•
Use a Phillips screwdriver and (6) 6/32 x ½” flathead screws to attach the
base stand (figure 2-a)
Place the Defender Series unit on a flat, stable surface in an upright position
resting on the base stand (figure 2-b)
3-a
o To Install Rack Mount Configuration – Option B
•
•
•
•
•
Use a Phillips screwdriver and (5) 6/32 x ¼” flathead screws to attach the
left rack bracket (figure 3-a)
Use a Phillips screwdriver and (6) 6/32 x ¼” flathead screws to attach the
right rack bracket (figure 3-a)
Insert the Defender Series unit into an available 1RU rack space from the
front of the rack (figure 3-b)
Product is designed for U-Space mounting only
Use (4) thumbscrews to secure the left and right rack brackets to the rack
rails (figure 3-b)
Use (4) cage nuts to secure the 4 thumbscrews to the rack (figure 3-b)
3-b
• Connect the Power Cables
oConnect the ancillary server equipment power plugs to the IEC output power
4-a
receptacles located on the rear panel of the Defender Series unit. Distribute
the equipment load evenly between the receptacle banks (figure 4-a)
oTo properly protect your system, connect all ancillary server equipment
(including UPS/Battery Backup) to the SurgeX Defender Series output power
receptacles; Refer to Common Configurations
section for reference
oCheck that the equipment you have connected to the Defender Series meets
the following electrical rating requirements:
• SX-DS-L630-FP: IMPORTANT: ONLY CONNECT EQUIPMENT RATED FOR USE WITH
NORTH AMERICAN 120/230VAC SPLIT PHASE
• SX-DS-L530-FP: IMPORTANT: ONLY CONNECT EQUIPMENT RATED FOR USE WITH
NORTH AMERICAN 120VAC SINGLE PHASE
• SX-DS-520-FP: IMPORTANT: ONLY CONNECT EQUIPMENT RATED FOR USE WITH
NORTH AMERICAN 120VAC SINGLE PHASE
• SX-DS-IEC-FP: IMPORTANT: ONLY CONNECT EQUIPMENT RATED FOR USE WITH 220240VAC SINGLE PHASE
• Secure the Power Cables – (optional)
oSecure equipment power cords to the cable organizer (if desired) using
cable ties or zip ties, to prevent accidental removal (figure 5-a)
© SurgeX
REV-A
5-a
Page 3
Defender Series Surge + PDU User Manual
• Plug in the Power Cord
oConnect the input power cord of the
SurgeX Defender Series to AC Mains.
Lock the SX-DS-L630-FP and SX-DSL530-FP plugs by turning to the right
(figure 6-a)
6-a
oDo not plug the unit into a UPS or
re-locatable power tap; UPS devices
should only be connected to the
SurgeX Defender Series unit
• Check Front Panel
oCheck the front panel to make sure the green “Outlets On” LED is lit
• If the green “Outlets On” LED is lit, your Defender Series unit
is ready to be used, and is protecting your server and ancillary
equipment (figure 7-a)
oIf the green “Outlets On” LED is not lit, but the red Wiring Fault Indicator
LED is lit, a wiring fault at the outlet has been detected. The SurgeX
unit will not operate until the Wiring Fault is resolved by a qualified
electrician. Refer to the “Front Panel LED Indicators” section for further
instructions (figure 7-b)
IV.
7-a
7-b
Common Configurations
• To properly protect your system, connect all ancillary server equipment (including UPS/Battery Backup)
to the SurgeX Defender Series output power receptacles (figure 8-a)
8-a
© SurgeX
REV-A
Page 4
Defender Series Surge + PDU User Manual
V.
Front Panel LED Indicators
• Power Indicator (Green); the green Power Indicator LED located on the left/top of
the front panel indicates that the electrical AC Mains is properly wired, and power is
available at the output power receptacles (figure 9-a)
• Wiring Fault Indicator (Red); the red Wiring Fault Indicator LED located to the right/
below the green Power Indicator LED on the front panel indicates that the electrical
AC Mains is not properly grounded, and power is not available at the output power
receptacles (figure 9-b)
oIf the red Wiring Fault indicator LED is illuminated, contact a licensed
electrician to inspect the electrical AC source outlet and repair as necessary
oSX-DS-L530-FP model only: The red Wiring Fault Indicator LED may also
indicate that the electrical AC Mains is improperly wired with the Line and
Neutral conductors reversed, and power is not available at the output power
receptacles
•
9-a
9-b
IMPORTANT: The presence of a safety Ground is essential to reduce the risk of electric shock. If the red
Wiring Fault indicator LED is illuminated, contact a licensed electrician to inspect the AC power source /
outlet and repair as necessary.
VI.
Over Voltage Conditions
• In the event of a long duration over-voltage condition, the unit will stop passing power to connected equipment
until the voltage returns to a safe operating level; this function is designed to protect your system
VII.
Other Information You May Need
•
Warning: See the safety and regulatory information that is shipped with your Defender Series unit.
Warranty information may be included within this document or as a separate document.
oThe User Manual provides information about product features and describes how to install and troubleshoot the unit; this
document is available online at surgex.com/defenderseries
oThe Quick Start guide that is shipped with your Defender Series unit describes how to install your system; this document is
available online at surgex.com/defenderseries
oThe Safety Guide that is shipped with your Defender Series unit describes all safety and regulatory information; this document
is available online at surgex.com/defenderseries
oNote: Always check for updated materials at surgex.com/defenderseries and read through these updated materials first,
because it may supersede information in other documents
•
VIII.
© SurgeX
Service Kits for replacement mounting hardware can be obtained by ordering Part #SX-DS-SK-MH
Technical Assistance
• If you do not understand these instructions or if the unit does not perform as expected, visit surgex.com/
defenderseries or email [email protected] for further assistance
REV-A
Page 5
Defender Series Surge + PDU User Manual
IX.
Specifications
SX-DS-L630-FP
SX-DS-L530-FP
SX-DS-520-FP
SX-DS-IEC-FP
Voltage Rating
120/230 Volts Split Phase
120 Volts Single Phase
120 Volts Single Phase
220-240 Volts Single Phase
Frequency
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
Load Rating
24 Amp Maximum Capacity
24 Amp Maximum Capacity
20 Amp Maximum Capacity
32 Amp Maximum Capacity
Input Connector
NEMA L6-30P
NEMA L5-30P
NEMA 5-20P
IEC-60309 332P65
Output Connector
(6) IEC-320 C13
(6) IEC-320 C13
(6) IEC-320 C13
(6) IEC-320 C13
Overload Protection
(2) Circuit Breaker
(2) Circuit Breaker
(2) Circuit Breaker
(3) Circuit Breaker
Voltage Protection
Rating (VPR)
800V Line - Line
500V Line - Ground
330V All Modes
330V All Modes
800V Line - Line
500V Line - Ground
Power Requirement
(no load)
8 Watts
8 Watts
8 Watts
8 Watts
Attenuation
Normal Mode:
>30dB 50kHz - 50MHz
Common Mode:
>30dB 150kHz - 50MHz
Normal Mode:
>30dB 50kHz - 50MHz
Common Mode:
>30dB 50kHz - 50MHz
Normal Mode:
>30dB 50kHz – 50MHz
Common Mode:
>30dB 50kHz – 50MHz
Normal Mode:
>30dB 50kHz - 50MHz
Common Mode:
>30dB 150kHz - 50MHz
Over-Voltage
Shutdown
280 Volts (±2%)
Restores at 260 Volts (±2%)
150 Volts (±2%)
Restores at 135 Volts (±2%)
150 Volts (±2%)
Restores at 135 Volts (±2%)
280 Volts (±2%)
Restores at 260 Volts (±2%)
Response Time
100 msec Over-Voltage
100 msec Over-Voltage
100 msec Over-Voltage
17.44” W x 12.08” D x 1.71” H
(1 RU)
100 msec Over-Voltage
Dimensions
17.44” W x 12.08” D x 1.71” H
(1 RU)
17.44” W x 12.08” D x 1.71” H
(1 RU)
17.44” W x 12.08” D x 1.71”
H
(1 RU)
Weight
12.5 lb
12.5 lb
12.5 lb
12.5 lb
Input Cord Length
3m
3m
3m
3m
Rack Mounting
Hardware
Included
Included
Included
Included
Standalone
Hardware
Included
Included
Included
Included
Power Indicator
LED (Green)
LED (Green)
LED (Green)
LED (Green)
Wiring Fault
Indicator
LED (Red) Illuminated when
no protective Earth Ground
present
LED (Red) Illuminated when
no protective Earth Ground
present or when Line/Neutral
reversed
LED (Red) Illuminated when
no protective Earth Ground
present or when Line/Neutral
reversed
LED (Red) Illuminated when
no protective Earth Ground
present
BTU/h
100 BTU/h Maximum at full
rated load
100 BTU/h Maximum at full
rated load
100 BTU/h Maximum at full
rated load
140 BTU/h Maximum at full
rated load
Temperature Range
5°C to 40°C
5°C to 40°C
5°C to 40°C
5°C to 40°C
Humidity Range
5% to 95% R.H. Noncondensing
5% to 95% R.H. Noncondensing
5% to 95% R.H. Noncondensing
5% to 95% R.H. Noncondensing
Agency Listings
TUV Certified to UL 60950-1
Check surgex.com/
defenderseries for country
specific certifications
TUV Certified to UL 60950-1
Check surgex.com/
defenderseries for country
specific certifications
TUV Certified to UL 60950-1
Check surgex.com/
defenderseries for country
specific certifications
CE/CB
Check surgex.com/
defenderseries for country
specific certifications
 Specifications subject to change without notice
 All listed specifications obtained at an ambient temperature of 25°
© SurgeX
REV-A
Page 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement