Clean Air Box Series Calibration Kit User Manual

Clean Air Box Series Calibration Kit User Manual
netzerotools.com
Clean Air Box Series Calibration Kit
User Manual
Kit includes:
Kit
CO Cylinder
Zero Air
Hardware
CABCK17L
17L 10 ppm
(CABCG1017L)
17L
(CABCG017L)
Regulator,
tubing, fitting
CABCK
34L 10 ppm
(CABCG10)
34L
(CABCG0)
Regulator,
tubing, fitting,
carrying case
CABCK103L
103L 10 ppm
(CABCG10103L)
103L
(CABCG0103L)
Regulator,
tubing,
fitting,
carrying case
11. Watch for the green LED to begin blinking. This indicates a successful zero.
Bullard recommends using impurity free test gas to perform Zero
adjustment. Bullard Zero air, CABCG0. Failure to observe this
recommendation may cause premature failure of the sensor.
WARNING
Use only 10 ppm CO gas for calibration. Using a higher concentration
may produce an inaccurate calibration and may damage the sensor.
Bullard CO gas CABCG10.
12. Verify by turning knob to TEST. LCD display should alternate between CO
and O or 1. If this does not occur, wait 5 minutes and re-zero.
13. Close the regulator on zero gas cylinder completely. Remove the
calibration connector fitting from the center of the knob.
NOTE
Knob must be in RUN position for active monitoring of CO in the air
supply.
14. With the incoming air flowing, turn the knob to RUN.
Calibration Instructions
Zero-Point Adjustment
Monitor calibration should be performed monthly or whenever the reading
may be questionable. A calibration schedule should be maintained for future
reference. To obtain an accurate calibration, we recommend the use of
Bullard calibration kits.
1. Connect compressed air source to CAB or COHP.
2. Allow air to pressurize system for 5-10 minutes.
3. Perform zero point adjustment and calibration.
Calibration Procedure
NOTE
If the unit is experiencing a temperature change of more than 20
degrees, wait 15-30 minutes before beginning calibration sequence.
Zero calibration should be performed before calibrating the monitor with CO
gas. Use impurity-free test gas.
Zero Adjustment Procedure
(Calibration is recommended only after a zero, so the unit will already be on.)
Rotate the knob located on the front of the monitor to the CAL position.
“AC” will appear on the display.
Attach the regulator to the calibration gas cylinder (10 ppm CO required).
Insert the calibration connector fitting into the center of the knob.
1. Remove the front cover of the CO Monitor.
2. Push the ON button. The unit will beep and begin a 60-second countdown.
3. Rotate the knob located on the front of the CO Monitor to the CAL position.
5. Press and hold the On/Off button until it beeps.
9. Open the cylinder valve fully. The flow rate is preset, so there is no need to
adjust it.
10. The red LED will continue to blink for approximately 90 seconds during
which the zero adjustment process will take place.
WARNING
4. “AC” will appear on the display.
8. Insert the calibration connector fitting into the center of the knob on the
front of the monitor. Open the cylinder valve fully. The flow rate is preset, and there is no need to
adjust it.
The Red LED on the front of the monitor will continue to blink for
approximately 90 seconds during which the calibration process will take
place.
6. “AO” will now appear on the display.
7. Attach the regulator to the zero gas cylinder.
netzerotools.com
netzerotools.com
Watch for the green LED to blink. This indicates a successful calibration.
Return Authorization
Verify by turning knob to TEST. LCD display should alternate between CO and
10 +/-1. If this does not occur, wait 5 minutes and repeat calibration.
The following steps must be completed before Bullard will accept any
returned goods. Please read carefully.
Close the regulator on CO gas cylinder completely and remove the calibration
connector fitting from the center of the knob.
Follow the steps outlined below to return goods to Bullard for repair or
replacement under warranty or for paid repairs:
Rotate the knob to the RUN position.
1.Contact Bullard Customer Service by telephone.
NOTE:
Knob must be in RUN position for active monitoring of CO in the air
supply.
The monitor is now calibrated and should be recalibrated monthly or on a
schedule with local requirements.
NOTE:
Typical calibration takes approximately 90 seconds. If unit will not
calibrate within 3 minutes, repeat the calibration steps with compressed
air turned off. If the problem persists, contact the Bullard Customer
Service Department at 1-877-BULLARD.
In your correspondence or conversation with Customer Service, describe the
problem as completely as possible. For your convenience, the representative
will try to help you correct the problem over the phone.
2. Verify with your representative that the product should be returned to
Bullard. Customer Service will provide you with written permission and a
return authorization number as well as the labels you will need to return the
product.
3. Before returning the product, decontaminate and clean it to remove any
hazardous materials which may have settled on the product during use. Laws
and/or regulations prohibit the shipment of hazardous or contaminated
materials. Products suspected to be contaminated will be professionally
discarded at the customer’s expense.
4. Ship returned products, including those under warranty, with all
transportation charges pre-paid. Bullard cannot accept returned goods on a
freight collect basis.
5. Returned products will be inspected upon return to the Bullard facility.
Bullard Customer Service will telephone you with a quote for required repair
work which is not covered by warranty. If the cost of repairs exceeds stated
quote by more than 20%, your coordinator will call you for authorization
to complete repairs. After repairs are completed and the goods have been
returned to you, Bullard will invoice you for actual work performed.
Bullard CAB100HA Clean Air Box Breathing Filtration System
Bullard CAB50HA5 Clean Air Box Breathing Filtration System
Bullard CAB30IRHA Clean Air Box Breathing Filtration System
Bullard CAB50HA Clean Air Box Breathing Filtration System
Bullard CAB30HA Clean Air Box Breathing Filtration System
netzerotools.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement