HDMI-1-ERM USER MANUAL
HDMI-1-ERM TOP VIEW
1. EQ Indicator
LED ON = Auto EQ
LED OFF = Manual EQ
HDMI-1-ERM REAR VIEW
1. EQ Adjustment
2. DC 5V 2A Power
3. EQ Indicator:
ON = Auto EQ
OFF = Manual EQ
4. Link Indicator for Local Monitor Output
5. RJ45 for CATx Output to Receiver
6. Local HDMI Monitor Output
7. Link Indicator
8. Power Indicator
9. RJ-45 HDMI Input
Troubleshooting Q & A
There is no image on the Local Monitor
Output
Check the following:
Cable Length
Cable Quality — low skew FTP cables
perform better than regular network cables.
Adjust the EQ knob slowly until the image
appears.
The output of display have noise or occasionally flashes
Check the following:
Cable Distance
Cable Quality
Slowly adjust the EQ knob on the HDMI-1
-R until the image appears. It is best to
use a pattern generator instead of the
source to perform this adjustment.
Check for excessive RF interference in the
room.
© 2012 APANTAC LLC, All rights reserved
7556 SW BRIDGEPORT ROAD
PORTLAND, OR 97224, USA
PHONE +1 503 968 3000
FAX +1 503 389 7921
The content of this document is provided in connection
with Apantac LLC (“Apantac”) products. Apantac makes
no representation or warranties with respect to the accuracy or completeness of the contents of this publication
and reserves the right to make changes to specifications
and product descriptions at any time without notice
HDMI-1-ERM
USER MANUAL
HDMI CATx
Extender/Receiver
with
Local Monitor Out
Package Contents
1 x HDMI-1-ERM
User Manual
Power Adapters (5V 2A)
Features
Can be used together with HDMI-1-E
or HDMI-1-EM to provide longer extension distance
Supports HDMI 1.2 and 1.3a
Local Monitor Output
Plug and Play
Magnetic mounting plate for easy
installation
Specifications
FEATURES/MODEL HDMI-1-ERM
Input
1 x RJ45
Output
Adjustment
1 x HDMI A-Type
Female, 1 x RJ-45
Equalizer
Max Resolution
1080p 60Hz
Cable Distance
18m/55ft @ 1080p
Power Adapter
5V 2A DC
Dimension (mm)
62 W x 113 x D 29 H
Installation
Connect HDMI monitor to HDMI-1-ERM.
Plug in the power.
Cascading: The RJ-45 <LINK IN> port is designed to receive the HDMI single from either
HDMI-1-E or HDMI-1-EM Extenders.
EQ ADJUSTMENT
In most cases the EQ Adjustment can be set
to Auto-mode by turning the dial all the way
counter clockwise.
If there are green and red dots on the HDMI
monitor, then adjust the EQ to manual mode.
Once you are in manual mode, adjust the EQ
very slowly as it is very sensitive
Once you are in manual mode, the “Auto” on
the top of the HDMI-1-ERM will turn off.
HDMI Pin Out
Pin
Signal
#
1 TMDS Data 2+
2
TMDS Data 2 Shield
12
TMDS Clock -
3
TMDS Data 2-
13
CEC
4
TMDS Data 1+
14
Reserved
(N.C. on device)
5
TMDS Data 1 Shield
15
SCL
6
TMDS Data 1-
16
SDA
7
TMDS Data 0+
17
DDC/CEC Ground
8
TMDS Data 0 Shield
18
+5 Power
9
TMDS Data 0-
19
Hot Plug Detect
10
TMDS Clock+
RECEIVERS
HDMI-1-R - long distance receiver - up to 115 ft (35
CATx Wiring
Identification Pin Assignment
Pair 1
EXTENDERS
HDMI-1-EM - Extender with local monitor output.
Pair 2
HDMI-SR - short distance receiver - up to 35 ft (10 m)
Pair 3
Pair 4
HDMI-1-EM - Extender with local monitor output.
Pin
Signal
#
11 TMDS Clock Shield
5
4
1
2
3
6
7
8
Color Code
White-Blue
Blue
White-Orange
Orange
White-Green
Green
White-Brown
Brown
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement