DA-VAEQ-6 User manual
DA-VAEQ-6
Analog Video Distribution Amplifier
with equalizer, gain, clamping and passive input loop
User manual
Rev. B
Nevion
Nordre Kullerød 1
3241 Sandefjord
Norway
Tel: +47 33 48 99 99
nevion.com
DA-VAEQ-6
Rev. B
Nevion Support
Nevion Europe
Nevion USA
P.O. Box 1020
3204 Sandefjord, Norway
Support phone 1: +47 33 48 99 97
Support phone 2: +47 90 60 99 99
1600 Emerson Avenue
Oxnard, CA 93033, USA
Toll free North America: (866) 515-0811
Outside North America: +1 (805) 247-8560
E-mail: [email protected]
See http://www.nevion.com/support/ for service hours for customer support globally.
Revision history
Current revision of this document is the uppermost in the table below.
Rev.
Repl.
Date
Sign
B
A
A
-
2013-05-06
2012-12-10
MR
MR
Change description
Several corrections and adjustments
Initial revision
nevion.com | 2
DA-VAEQ-6
Rev. B
Contents
Revision history ........................................................................................................ 2
1 Product overview ................................................................................................... 4
2 Specifications ........................................................................................................ 5
2.1 Electrical Input............................................................................................................... 5
2.2 Electrical Output ............................................................................................................ 5
2.3 Analog video ................................................................................................................. 5
2.4 Electrical ....................................................................................................................... 5
3 Connections .......................................................................................................... 6
3.1 Mounting the connector module .................................................................................... 6
4 Operation............................................................................................................... 7
4.1 GPI ALARM – Module Status Outputs........................................................................... 7
4.2 Front Panel - Status Monitoring and Signal Detection ................................................... 7
4.3 Gain and EQ adjustment ............................................................................................... 8
4.4 Choosing termination at input ports ............................................................................... 8
4.5 DIP settings................................................................................................................... 9
General environmental requirements for Nevion equipment .................................. 10
Product Warranty.................................................................................................... 11
Appendix A Materials declaration and recycling information .................................. 12
A.1 Materials declaration ....................................................................................................12
A.2 Recycling information...................................................................................................12
nevion.com | 3
DA-VAEQ-6
Rev. B
1 Product overview
The Flashlink DA-VAEQ-6 is an analog video distribution amplifier module with input
equalizer, gain, black level clamping and passive input loop providing high performance
media distribution for analog standard definition video signals . The input signal can be
equalized for up to 300m of cable and is distributed to 6 equivalent outputs. Both
equalization and gain can be controlled on potentiometers accessed at the front of the card.
The input is switchable to high impedance for multi drop purposes. Outputs have 75 ohms
impedance. A signal detector will indicate if signal is present (LED and GPI).
The DA-VAEQ-6 is designed for all standard definition analog video distribution purposes in
studio, duplication and broadcast applications.
The DA-VAEQ-6 is well suited for distribution of AES-3id signals (75 ohms unbalanced AES
over coaxial cables).
Equalization
control
Gain
control
Figure 1: DA-VAEQ-6 Analog Video Distribution Amplifier
nevion.com | 4
DA-VAEQ-6
Rev. B
2 Specifications
2.1 Electrical Input
Maximum input
1 V p-p
Equalization
Tunable up to 300m of Belden 8281 or equal.
Coupling
DC
Impedance
75 ohm (switchable to high impedance)
Connector
2x BNC connected in parallel (1 input + 1 loop)
2.2 Electrical Output
Number of outputs
6
Connector
BNC
Impedance
75 ohm
Signal polarity
6 non inverting
2.3 Analog video
Noise bandwidth, -3dB
Formats
0 to 10 MHz (useful for AES-3id)
Standard definition video
Return loss
> 35dB 0-10MHz
Video S/N ratio
> 70 dB
Differential gain
< 0.3%
Differential phase
< 0.3º
Gain adjustment
+/-3dB
Freq. response
0 dB ± 0.3 dB 0- 6 MHz
2.4 Electrical
Power
+5V DC / 3 W,
±15V DC / 3 W
Control
Control system for access to setup and module status with
BITE (Built-In Test Equipment) for use with GYDA Control
System
nevion.com | 5
DA-VAEQ-6
Rev. B
3 Connections
The DA-VAEQ-6 has a dedicated connector module: DA-VA-C2. This module is mounted at
the rear of the sub-rack. The module is shown in figure 2.
Figure 2: Overview of the DA-VA-C2 connector module (default backplane).
The electrical input signal is connected to the two IN BNCs, and the electrical outputs are
connected to the O1 to O6 BNC’s. Please note that all 6 outputs are non-inverted. On the
back side of this board, there is a DIP switch (see figure 5 in chapter 4.4) to set the
termination. If switch 1 is on, there is a 75 ohms termination. DIP switch 2 is not used.
3.1 Mounting the connector module
The details of how the connector module is mounted, is found in the user manual for the
sub-rack frame FR-2RU-10-2.
This manual is also available from our web site: http://www.nevion.com/
nevion.com | 6
DA-VAEQ-6
Rev. B
4 Operation
The equalization and gain can be controlled from two potentiometers.
The status of the module can be monitored in three ways.
1. GYDA System Controller (optional)
2. GPI at the connector module
3. LED’s at the front edge of the module
Of these three, the GPI and the LED’s are mounted on the module itself, whereas the
GYDA System Controller is a separate module giving detailed information on the card
status. The functions of the GPI and the LED are described in sections 5.1 and 5.2. The
GYDA controller is described in a separate user manual.
4.1 GPI ALARM – Module Status Outputs
Only available when using the standard –C1 backplane
These outputs can be used for wiring up alarms for third party control systems. The GPI
outputs are open collector output, sinking to ground when an alarm is triggered. The GPI
connector is shown in figure 4.
Electrical Maximums for GPI outputs
Max current: 100mA
Max voltage: 30V
Figure 3: GPI pin out
DA-VAEQ-6 module GPI pinning:
Signal
Status
Signal
Ground
Name
General error status for the module.
Signal detected
0 volt pin
Pin #
Pin 1
Pin 2
Pin 8
Mode
Open Collector
Open collector
0V.
4.2 Front Panel - Status Monitoring and Signal Detection
The status of the module can be monitored visually at the front of the front of the module.
The DA-VAEQ-6 has one LED showing the status. The hardware revision 2 of the DAVAEQ-6 has also a built in detector for signal monitoring. When signal is present, LED is
green, otherwise it will be red. The LEDs are described in the following table:
Diode \ state
Red LED
Status
Module is faulty
Signal
No signal detected
Yellow LED
Green LED
Module is OK
Module power is OK
Signal present
No light
Module has no
power
Module has no
power
nevion.com | 7
DA-VAEQ-6
Rev. B
4.3 Gain and EQ adjustment
For location of potentiometers see figure 4 below.
Gain pot:
11 turns. Clockwise operation increases the gain
EQ pot:
11 turns. Clockwise operation increases equalization rate
Figure 4
4.4 Choosing termination at input ports
For location of switch see figure 5 below.
75-ohm termination to be chosen when looping function is not used.
See also chapter 3. Connections.
Figure 5
nevion.com | 8
DA-VAEQ-6
Rev. B
4.5 DIP settings
DIP settings to be in accordance with figure 6.
Figure 6
nevion.com | 9
DA-VAEQ-6
Rev. B
General environmental requirements for Nevion equipment
1.
2.
-
The equipment will meet the guaranteed performance specification under the following
environmental conditions:
Operating room temperature range: 0°C to 45°C
Operating relative humidity range:
<90% (non-condensing)
The equipment will operate without damage under the following environmental
conditions:
Temperature range:
-10°C to 50°C
Relative humidity range:
<95% (non-condensing)
nevion.com | 10
DA-VAEQ-6
Rev. B
Product Warranty
The warranty terms and conditions for the product(s) covered by this manual follow the
General Sales Conditions by Nevion, which are available on the company web site:
www.nevion.com
nevion.com | 11
DA-VAEQ-6
Rev. B
Appendix A Materials declaration and recycling
information
A.1 Materials declaration
For product sold into China after 1st March 2007, we comply with the “Administrative
Measure on the Control of Pollution by Electronic Information Products”. In the first stage of
this legislation, content of six hazardous materials has to be declared. The table below
shows the required information.
Toxic or hazardous substances and elements
組成名稱
Part Name
DA-VA-EQ-6
鉛
汞
镉
六价铬
多溴联苯
Lead Mercury Cadmium Hexavalent Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
biphenyls
(Cr(VI))
(PBB)
O
O
O
O
O
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is
below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used
for this part is above the limit requirement in SJ/T11363-2006.
This is indicated by the product marking:
A.2 Recycling information
Nevion provides assistance to customers and recyclers through our web site
http://www.nevion.com/. Please contact Nevion’s Customer Support for assistance with
recycling if this site does not show the information you require.
Where it is not possible to return the product to Nevion or its agents for recycling, the
following general information may be of assistance:




Before attempting disassembly, ensure the product is completely disconnected from
power and signal connections.
All major parts are marked or labeled to show their material content.
Depending on the date of manufacture, this product may contain lead in solder.
Some circuit boards may contain battery-backed memory devices.
nevion.com | 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement