Operating Instructions DAP

Operating Instructions DAP
User manual M1
User manual M1
Current loop 4-20 mA
Current loop 4-20 mA
Operating Instructions
DAP-10166B0S
Current loop 4-20 mA
Technical features:
Technical features:
• red display of -1999…9999 digits
minimal
installation
depth: 40
mm without plug-in terminal
• red
display
of -1999…9999
digits
adjustment
via factory
default
or directly
the sensor
signal
• minimal
installation
depth:
40 mm
withouton
plug-in
terminal
min/max-value
recording
• adjustment
via factory
default or directly on the sensor signal
10 adjustable setpoints
• min/max-value
recording
display
flashing
at threshold exeedance / undercut
• 10
adjustable
setpoints
tara / offset
value
calibrationexeedance / undercut
• display
flashing
at threshold
programming
interlock
via access code
• tara
/ offset value
calibration
protection class
IP65 atvia
theaccess
front code
• programming
interlock
plug-in terminal
• protection
class IP65 at the front
option: terminal
2 galv. insulated switching outputs
• plug-in
pc-based
configuration
PM-TOOL
with CD & USB adapter for devices without keypad,
• option:
2 galv.
insulatedkit
switching
outputs
for
a
simple
adjustment
of
standard
devices
• pc-based configuration kit PM-TOOL with CD & USB adapter for devices without keypad,
for a simple adjustment of standard devices
M1_3S.GB.pdf update: 01.10.2013
96x24
M1_3S.GB.pdf update: 01.10.2013
96x24
Order code
6
power supply
4...20 MA, 2-wire current loop display
6
DAP-101
2
function input
4...20mA, 2-wire current loop display
B
function output
0
6
6
display (current loop)
standard configuration
S
B
0
standard, protection IP65
S
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
Contents
1.
Assembly
2
2.
Electrical connection
3
3.
Function- and operation description
5
4.
Setting up the device
6
4.1. Switching on
6
4.2. Standard parameterization
6
4.3. Extended parameterization
7
4.3.1. MIN/MAX value inquiry
8
4.3.2. Flashing of display
8
4.3.3. Threshold values
8
4.3.4. Setpoints
10
4.4. Reset to default settings
10
5.
Technical data
12
6.
Safety advice
13
7.
Error elimination
14
1
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
3
1. Assembly
1. Assembly
Please read the Safety instructions on page 17 before installation and keep this user manual for future reference.
24,0
3,0
Se
alin
g
96
,0
l.
inc
h
t
,0
63 n dep mp
tio l cla
alla mina
t
s
In ter
Gap for physical unit
1.
2.
3.
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
2
4
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
2. Electrical connection
2. Electrical connection
Type
DAP-10166B0S
Typ M3-1S
R4B.0001.K70BD – device without switching points
Type
DAP-10166B0S
Typ M1-3S
R4B.0001.K72BD – device with switching points
Connection examples:
Below you find some connection examples, which demonstrate some practical applications:
3
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5
2. Electrical connection
Connection examples
6
4
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
3. Function- and operation description
3. Function and operation description
Operation
The operation is divided into two different levels.
Menu Level
Here it is possible to navigate between the individual menu items.
Parameterization level:
The parameters stored in the menu item can be parameterized here.
Functions that can be adjusted or changed are always indicated with a flashing of the display. Adjustments made
at the parameterization level should be always confirmed by pressing the [P] key to save them.
However, the display automatically saves all adjustments and then switches to operation mode if no further keys
are pressed within 10 seconds.
Level
Button
Description
Change to parameterization level with the relevant parameters
Menu level
For navigation at the menu level
To confirm the changes made at the parameterization level
Parameterization level
To change the value or setting
Example:
Menu Level
Parameterization level
Programming via configuration software PM-TOOL-MUSB6
You receive the software on CD incl. an USB-cable with a device adaptor. The connection is done via a 6-pole
micromatch connector plug on the back and the PC is connected via an USB connector plug.
System requirements:
PC with USB interface
Software:
Windows XP, Windows Vista
5
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
7
4. Setting-up of the device
4. Setting up the device
4.1. Switching on
Once the installation is complete, you can start the device by applying the current loop. Check beforehand
once again that all the electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8) is displayed, followed by an indication
of the software type and, after that, also for 1 second, the software version. After the start-up sequence, the
device switches to operation/display mode.
4.2. Standard parameterization:
To be able to parameterize the display, press the [P] key in operating mode for 1 second. The display then
changes to the menu level with the first menu item TYPE.
Menu level
Parameterization level
Selection of the input signal, TYPE:
Default: sens
There are two measuring input options for the current loop: 4-20 mA as works calibration
(without application of the sensor signal) and Sens as sensor calibration (with the sensor
applied). Confirm the selection with [P] and the display switches back to the menu level.
Setting the measuring range end value, END:
Default: 2000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the highest value digit. After the last digit, the
display switches back to the menu level. If Sens was selected as the input option, you can only
select between noca and cal. With noca, only the previously set display value is taken over, and
with cal, the device takes over both the display value and the analogue input value.
Setting the measuring range start/offset value, offs:
Default: 0400
Enter the start/offset value from the smallest to the highest digit [▲] [▼] and confirm each digit
with [P]. After the last digit the display switches back to the menu level. If Sens was selected as
the input option, you can only select between noca and cal. With noca, only the previously set
display value is taken over, and with cal, the device takes over both the display value and the
analogue input value.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P]. The
display then switches back to the menu level again.
6
8
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
4. Setting-up of the device
Menu level
Parameterization level
Setting the display time, SEC:
Default: 01.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 to 10.0 seconds. Confirm the selection by pressing the [P] button. The
display then switches back to the menu level again.
Activation / deactivation of the programming lock and completion of the standard
parameterization, run:
Default: uloc
With the aid of the [▲] [▼] keys, you can choose between the deactivated key lock Uloc (works
setting) and the activated key lock Loc. Make the selection with [P]. After this, the display
confirms the settings with "- - - -", and automatically switches to operating mode. If Loc was
selected, the keyboard is locked. To get back into the menu level, you must press [P] for 3
seconds in operating mode. You must now enter the CODE (works setting 1 2 3 4) that appears
using the [▲] [▼] keys plus [P] to unlock the keyboard. FAIL appears if the input is wrong.
4.3. Extended parameterization
By pressing the [▲] & [▼] buttons during standard parameterization for one second, the display switches to
the extended parameterization mode.
The operation is the same as in standard parameterization.
Menu level
Parameterization level
Rescaling the measuring input values, EndA:
Default: 20.00
With the aid of this function, you can rescale the input value of 4-20 mA (works setting) without
applying a measuring signal. If sensor calibration has been selected, these parameters are not
available.
Rescaling the measuring input values, OFFA:
Default: 4
With the aid of this function, you can rescale the input value of 4-20 mA (works setting) without
applying a measuring signal. If sensor calibration has been selected, these parameters are not
available.
7
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
9
4. Setting-up of the device
Menu level
Parameterization level
Setting the tare /offset value, tArA:
Default: 0
The given value is added to the linerarized value. In this way, the characteristic line can be
shifted by the selected amount.
Zero point slowdown, ZErO:
Default: 0
With zero point slowdown, a value range around zero can be preselected at which the display
shows zero. If, for example, a 10 is set, the display would show a zero in the range from -10 to
+10 and continue below it with -11 and above it with +11.
4.3.1. MIN/MAX value inquiry - Assignment of key functions, Tast:
Default: no
Here, you can enter for the operating mode either a min/max-value inquiry or a threshold value
correction on the arrow keys.
If the min/max-memory is activated with EHER, the measured min/max-values will be saved
during operation and can be called up via the arrow keys [▲] [▼]. The values are lost if the
device is restarted.
If the threshold value correction LI.1 is selected, the limit values can be changed during
operation without hindering the operating procedure.
With tara the display is tared to zero and is saved permanently as offset. The device confirms
the correct taring by showing 0000 in the display. If No is parameterized, the navigation keys
[▼] [▲] have no function in operating mode.
4.3.2. Flashing of display, FLAS:
Default: no
Here, flashing of the display can be added as an extra alarm function, either to the first limit
value (select: LI-1), the second limit value (select: LI-2) or to both limit values (select: LI-12). With
No (works setting), no flashing is assigned at all.
4.3.3. Limit values / Limits, LI-1:
Default: 0800
For both limit values, two different values can be parameterized. With this, the parameters for
each limit value are called up one after the other.
8
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
4. Setting-up of the device
Menu level
Parameterization level
Hysteresis for limit values, HY-1:
Default: 0000
For both limit values, a hysteresis function exists that reacts according to the functional
principle (operating current / quiescent current).
Function if display falls below / exceeds limit value, FU-1:
Default: hi9h
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
Limit value /Limits, LI-2:
Default: 1200
For both limit values, two different values can be parameterized. With this, the parameters for
each limit value are called up one after the other.
Hysteresis for limit values, HY-2:
Default: 0000
For both limit values, a hysteresis function exists that reacts according to the functional
principle (operating current / quiescent current).
Function if display falls below / exceeds limit value, FU-2:
Default: hi9h
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
9
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
11
4. Setting-up of the device
Menu Level
Parameterization level
Setting the code, CODE:
Default: 1234
With this setting, it is possible to select an individual code (works setting 1 2 3 4) for locking the
keyboard. To locl/release the key, proceed according to menu item run.
4.3.4. Set points - Number of additional set points, SPCt:
Default: 0
In addition to the start and end value, 8 extra set points can be defined to linearize non-linear
sensor values. Only the activated set point parameters are displayed.
Display values for setpoints, dIS1 … dIS8:
Under this parameter the value of the setpoints is defined. With sensor calibration, as with end
value/offset, you will be asked at the end whether a calibration should be made.
Analogue values for setpoints, INP1 … INP8:
The set points are only displayed with the works calibration (4-20 mA) Here, the desired
analogue values can be freely selected. The input of constantly rising analogue values must be
carried out by the customer/user.
4.4. Reset to default values
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on loop current (approx. 3.8 mA) and press [P]-button until „- - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent operation. This puts
the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
12
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
4. Setting-up of the device
Functional principle of the setpoints
Limit value exceedance “High”
By limit value exceedance the alarm
S1-S2 is off below the threshold and
on on reaching the threshold.
Limit value undercut “low”
By limit value undercut the alarm
S1-S2 is on below the threshold
and switched off on reaching the
threshold.
Alarms / optical setpoint display
An activated set point can be optically indicated by flashing of the 7-segment display.
Functional principle of the alarms
Alarm
Deactivated, display value
Threshold
Threshold/limit value for switch over
Hysteresis
Width of the window between the thresholds
Operating principle
Operating current / quiescent current
11
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
13
5. Technical data
5. Technical data
Housing
Dimensions
96x48
96x48x40 mm (BxHxD)
96x48x63 mm (BxHxD) including plug-in terminal
Panel cut-out
96x48
92.0+0,8 x 45.0+0.6 mm
Insulation thickness
up to 3 mm
Fixing
snap-in screw element
Material
PC Polycarbonate, black
Sealing material
EPDM, 65 Shore, black
Protection class
standard IP65 (front), IP00 (back side)
Weight
approx. 100 g
Connection
plug-in terminal; wire cross section up to 2.5 mm2
Display
Digit height
14 mm
Segment colour
red
Display range
-1999 to 9999
Setpoints
optical display flashing
Overflow
horizontal bars at the top
Underflow
horizontal bars at the bottom
Display time
0.1 to 10.0 seconds
Input
Measuring range
Measuring fault
Digit
min. 3.5…max. 21 mA
4 – 20 mA
0.3 %
±1
Fail of voltage
approx. 5.1 V without switching outputs
approx. 8.0 V with switching outputs
Measuring range / Input resistance / Measuring fault at measuring time = 1 second
14
Temperature drift
100 ppm / K
Measuring time
0.1…10.0 seconds
Measuring principle
successive approximation
Resolution
12 Bit-converter
14 Bit (noiseless by oversampling at 1s measuring time)
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
12
6. Error elimination
Output
Setpoints
Potential free PhotoMos-Outputs
max. switching voltage 30 VDC/AC
max. steady current 0.4 A
Electric strength AC: 400 V permanent, 1800 V for 1 min
Memory
Flash-memory (independent of supply)
Data life
≥ 100 years
Ambient conditions
Working temperature
0…60°C
Storing temperature
-20…80°C
Climatic density
relative humidity 0-80% on years average without dew
EMV
EN 61326
CE-sign
Conformity to directive 2004/108/EG
Safety standard
according to low voltage directive 2006/95/EG
EN 61010; EN 60664-1
6. Error elimination
Below please find the recommended procedure for dealing with faults and locating their possible cause.
6.1. Questions and answers
I.
The display of the device is dark
•
•
Check the current loop current of the device
Please contact the manufacturer if errors of this kind occur
II.
The device shows
Displayed overflow at exceedance of display/measuring range
Displayed overflow at undershooting of display/measuring range
III. The device shows
Loop current < 3,5 mA
13
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
15
7.
7. Safety
Safety advices
advices
7.
7. Safety
Safety advice
advice
Please
Please read
read the
the following
following safety
safety advice
advice and
and the
the assembly
assembly chapter
chapter 1
1 before
before installation
installation and
and keep
keep it
it
for
future
reference.
for future reference.
Proper
Proper use
use
The
designed
evaluation
display
of current
loop
signals.
With
The
M1-3S-device
designed
for
the
evaluation
and
display
of
loop
signals.
With
the
The DAP-101-device
M1-3S-device is
is is
designed
forfor
thethe
evaluation
andand
display
of current
current
loop
signals.
With
the the
setpoints,
it
is
possible
to
perform
simple
control
tasks
(only
possible
for
devices
with
setpoints).
setpoints, it
setpoints,
it is
is possible
possible to
to perform
perform simple
simple control
control tasks
tasks (only
(only possible
possible for
for devices
devices with
with setpoints).
setpoints).
Danger!
Danger! Careless
Careless use
use or
or improper
improper operation
operation can
can result
result in
in
personal
personal injury
injury and/or
and/or damage
damage to
to the
the equipment.
equipment.
Control
Control of
of the
the device
device
The
The panel
panel meters
meters are
are checked
checked before
before dispatch
dispatch and
and sent
sent out
out in
in perfect
perfect condition.
condition. Should
Should there
there be
be
any
visible
damage,
we
recommend
close
examination
of
the
packaging.
Please
inform
the
any visible damage, we recommend close examination of the packaging. Please inform the
supplier
supplier immediately
immediately of
of any
any damage.
damage.
Installation
Installation
The DAP-101-device must be installed by a suitably qualified specialist (e.g. with a qualification in
The
must
The M1-3S-device
M1-3S-device
must be
be installed
installed by
by a
a suitably
suitably qualified
qualified specialist
specialist (e.g.
(e.g. with
with a
a qualification
qualification in
in
industrial
electronics).
industrial
electronics).
industrial electronics).
Notes
Notes on
on installation
installation
•• There
There must
must be
be no
no magnetic
magnetic or
or electric
electric fields
fields in
in the
the vicinity
vicinity of
of the
the device,
device, e.g.
e.g. due
due to
to transformers,
transformers,
mobile
mobile phones
phones or
or electrostatic
electrostatic discharge.
discharge.
•• Do
Do not
not install
install inductive
inductive consumers
consumers (relays,
(relays, solenoid
solenoid valves
valves etc.)
etc.) near
near the
the device
device and
and suppress
suppress
any
interference
with
the
aid
of
RC
spark
extinguishing
combinations
or
free-wheeling
diodes.
any interference with the aid of RC spark extinguishing combinations or free-wheeling diodes.
•• Keep
one another
parallel with
Keep input,
input, output
output and
and supply
supply lines
lines separate
separate from
from one
another and
and do
do not
not lay
lay them
them parallel
with
each
other.
Position
“go”
and
“return
lines”
next
to
one
another.
Where
possible
use
twisted
pair.
each other. Position “go” and “return lines” next to one another. Where possible use twisted pair.
So,
So, you
you receive
receive best
best measuring
measuring results.
results.
•• Screen
Screen off
off and
and twist
twist sensor
sensor lines.
lines. Do
Do not
not lay
lay current-carrying
current-carrying lines
lines in
in the
the vicinity.
vicinity. Connect
Connect the
the
screening
on
one
side
on
a
suitable
potential
equaliser
(normally
signal
ground).
screening on one side on a suitable potential equaliser (normally signal ground).
•• The
The device
device is
is not
not suitable
suitable for
for installation
installation in
in areas
areas where
where there
there is
is a
a risk
risk of
of explosion.
explosion.
•• Any
Any electrical
electrical connection
connection deviating
deviating from
from the
the connection
connection diagram
diagram can
can endanger
endanger human
human life
life and/or
and/or
can
can destroy
destroy the
the equipment.
equipment.
•• The
The terminal
terminal area
area of
of the
the devices
devices is
is part
part of
of the
the service.
service. Here
Here electrostatic
electrostatic discharge
discharge needs
needs to
to be
be
avoided.
avoided. Attention!
Attention! High
High voltages
voltages can
can cause
cause dangerous
dangerous body
body currents.
currents.
•• Galvanic
Galvanic insulated
insulated potentials
potentials within
within one
one complex
complex need
need to
to be
be placed
placed on
on an
an appropriate
appropriate point
point
(normally
earth
or
machines
ground).
So,
a
lower
disturbance
sensibility
against
impacted
energy
(normally earth or machines ground). So, a lower disturbance sensibility against impacted energy
can
can be
be reached
reached and
and dangerous
dangerous potentials,
potentials, that
that can
can occur
occur on
on long
long lines
lines or
or due
due to
to faulty
faulty wiring,
wiring, can
can
be
avoided.
be avoided.
M1_3S.GB.pdf
M1_3S.GB.pdf
16
14
14
update:
update: 01.10.2013
01.10.2013
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
17

Pegel
Druck


Temperatur Durchfluss
Registrierung
Visualisierung
¸



Füllstand



Messumformer
Sensorik
USV
Wir erwarten Ihren Anruf.
ACS-CONTROL-SYSTEM GmbH
Lauterbachstr. 57
D- 84307 Eggenfelden
know how mit System
Ihr Partner für Messtechnik und Automation
¸
[email protected]
www.acs-controlsystem.de
Stand 10/2013
ACS-CONTROL-SYSTEM
Tel: +49 (0) 8721-9668-0
Fax: +49 (0) 8721-9668-30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement