advertisement
Register your product and get support at
www.philips.com/welcome
HTS3180
HTS3181
EN User manual
DE Benutzerhandbuch
ES
FR
Manual del usuario
Mode d’emploi
NL Gebruiksaanwijzing
Downloaded From TheatreSystem-Manual.com Manuals
2
Downloaded From TheatreSystem-Manual.com Manuals
Contents
1 Important
Safety and important notice
Trademark notice
4
4
5
Feature highlights
Product overview
6
6
6
3 Connect
Place the product
Connect video cables
Connect speakers and subwoofer
9
9
9
10
Connect radio antenna 11
Connect audio cables/other devices 11
Connect power cord 12
13
Insert the remote control batteries 13
Find the correct viewing channel
Select menu display language
Change speaker settings
Select a play source
13
14
14
15
5 Play
Play a disc
Play video
Play music
Play photo
Play from USB device
Play from radio
16
16
16
19
20
21
21
Control the volume
Select surround sound
Select a preset sound
23
23
23
23
General setup
Audio setup
Video setup
24
24
25
26
Update software
10 Troubleshooting
11 Glossary
Downloaded From TheatreSystem-Manual.com Manuals
EN 3
29
29
30
31
33
1 Important
Safety and important notice
Warning
•
•
•
•
•
•
•
Risk of overheating! Never install the product in a confi ned space. Always leave a space of at least 4 inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product.
Never place the product, remote control or batteries near naked fl ames or other heat sources, including direct sunlight.
Only use this product indoors. Keep this product away from water, moisture and liquidfi lled objects.
Never place this product on other electrical equipment.
Keep away from this product during lightning storms.
Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
Visible and invisible laser radiation when open.
Avoid exposure to beam.
This product is in compliance with the essential requirements and other relevant provisions of Directives 2006/95/EC (Low
Voltage), 2004/108/EC (EMC).
Copyright
This equipment should not be used for such purposes.
Macrovision copyright
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Copyright in the U.K.
Recording and playback of material may require consent. See Copyright Act 1956 and
The Performers’s Protection Acts 1958 to
1972.
Mains fuse (UK only)
This product is fi tted with an approved moulded plug. Should it become necessary to replace the mains fuse, this must be replaced with a fuse of the same value as indicated on the plug (example 10A).
1
Remove fuse cover and fuse.
2
The replacement fuse must comply with
BS 1362 and have the ASTA approval mark. If the fuse is lost, contact your dealer in order to verify the correct type.
3
Refi t the fuse cover.
Note
• To conform with the EMC directive
(2004/108/EC), the mains plug on this product must not be detached from the mains cord.
The making of unauthorized copies of copy-protected material, including computer programmes, fi les, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offence.
4 EN
Downloaded From TheatreSystem-Manual.com Manuals
Disposal of your old product and batteries
Trademark notice
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby
Laboratories.
When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive
2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with your normal household waste.
Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.
DivX, DivX Ultra Certifi ed, and associated logos are trademarks of DivX, Inc. and are used under license.
Offi cial DivX® Ultra Certifi ed product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX® media fi les and the DivX® Media Format.
Plays DivX® video with menus, subtitles and audio tracks.
Windows Media and the Windows logo are trademarks, or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste.
Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, inc.
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks.
CLASS 1
LASER PRODUCT
EN 5
Downloaded From TheatreSystem-Manual.com Manuals
Congratulations on your purchase, and welcome to Philips! To fully benefi t from the support that Philips offers, register your product at www.philips.com/welcome.
Feature highlights
Listen to rich uncompressed multi-channel surround sound
This Home Theater System supports 5.1 channels of uncompressed audio that delivers a real-to-life sound experience as if you are listening to it live.
USB direct
Simply plug your USB device into the USB jack to play your MP3/WMA/JPEG/DivX fi les.
Sync the audio output with the video play
Synchronize audio and video by delaying the audio output if the video signal sent to the TV is slower than the audio streams.
Screen Fit
View the movie in full screen display on any
TV. It is only applicable to DVD and JPEG fi les.
Product overview
Remote control
q r s t u v w x o p
Region codes
You can play discs with the following region codes.
DVD region code Countries
Europe
Russia a
( Standby-On )
• Turns on the Home Theater System or switches to standby mode.
b ( Open/Close )
• Opens or closes the disc compartment.
c Source buttons
• AUDIO SOURCE: Selects an audio input source.
• RADIO: Switches to FM radio.
• USB: Switches to the USB source.
• DISC: Switches to the disc source.
k l m n a b c d e f g h i j
6 EN
Downloaded From TheatreSystem-Manual.com Manuals
d
SETUP
• Accesses or exits the setup menu.
e
•
•
•
•
( Navigation buttons )
Navigates through the menus.
Press left and right for fast backward or forward search.
In radio mode, press up and down to tune the radio frequency.
In radio mode, press left or right to start auto search.
f
INFO
• For discs, displays information about the current status or the disc.
• For slideshows, displays a thumbnail view of photo fi les.
g
•
•
( Play/Pause )
Starts, pauses or resumes disc play.
In radio mode, automatically tune radio stations during fi rst-time setup.
h
( Stop )
• Stops disc play.
• In radio mode, erases the current preset radio station.
i SURR ( Surround Sound )
• Switches to supported surround sound or stereo sound.
j AUDIO SYNC
• Selects an audio language or channel.
• Press and hold to access the setting for audio sync, then press VOL +/- to set the audio delay time.
k Numeric buttons
• Selects an item to play.
l SUBTITLE
• Selects a subtitle language for video.
m SCREEN FIT
• Fits the picture format to the TV screen (using zoom factor 1.3X and
1.6X).
n ZOOM
• Zooms in or out of the picture.
o SLEEP
• Sets a delay after which the home theater system switches to standby.
p OK
• Confi rms an entry or selection.
q
BACK
• Returns to a previous screen.
• For DVD, goes to the title menu.
• For VCD version 2.0 or SVCD with
PBC turned on, returns to the menu during playback.
r
/ ( Previous/Next )
• Skips to the previous or next title, chapter, or track.
s
( Mute )
• Mutes or restores audio output.
t VOL +/-
• Increases or decreases volume.
u SOUND
• Selects a predefi ned sound effect.
v ANGLE
• Displays video from different camera angles.
w REPEAT / PROGRAM
• Selects or turns off repeat or shuffl e
• mode.
In radio mode, resets the list of preset stations: press to manually reset; press and hold to automatically reset.
x REPEAT A-B
• Marks the section for repeat play, or turns off repeat mode.
EN 7
Downloaded From TheatreSystem-Manual.com Manuals
Main unit
a b c d e f g h i a
( Standby-On )
• Turns on the Home Theater System or switches to standby mode.
b Disc compartment c ( Open/Close )
• Opens or closes the disc compartment.
d
•
•
( Play/Pause )
Starts, pauses or resumes disc play.
In radio mode, automatically tune radio stations during fi rst-time setup.
e
( Stop )
• Stops disc play.
• In radio mode, erases the current preset radio station.
f SOURCE
• Selects a media to play or listen to audio from the connected device.
g Display panel h VOLUME
• Increases or decreases volume.
i
•
( USB )
Connects a USB supported device.
8 EN
Downloaded From TheatreSystem-Manual.com Manuals
3 Connect
Make the following connections to use your
Home Theater System.
•
•
Basic connections:
Video
Speakers and subwoofer
• Power
Optional connections:
• Radio antenna
• Audio
• Audio from TV
• Audio from cable box/recorder/ game console
• Other devices
• USB device
Note
•
•
Refer to the type plate at the back or bottom of the product for identifi cation and supply ratings.
Before you make or change any connections, ensure that all devices are disconnected from the power outlet.
Tip
•
Different types of connectors can be used to connect this product, depending on availability and your needs. A comprehensive interactive guide to help you connect your product is available at www.connectivityguide.philips.
com.
Place the product
•
•
Place the product where it cannot be pushed, pulled over or knocked down.
Do not place it in an enclosed cabinet.
Be sure that you have full access to the power cord for easy disconnection of the product from the power supply.
REAR
LEFT
FRONT
LEFT
CENTER
FRONT
RIGHT
REAR
RIGHT
SUBWOOFER
1
Place the home theater near your TV.
2
Place the speakers system at normal listening height and parallel to your listening area.
3
Place the subwoofer in the corner of the room or at least 1 meter/3 feet away from your TV.
Tip
•
To reduce interference or noise, place the home theater away from radiation devices.
Connect video cables
Connect this Home Theater System to TV to view disc play. Select the best video connection that the TV can support.
• Option 1: Connect to the SCART jack
(for a standard TV).
• Option 2: Connect to the VIDEO jack
(for a standard TV).
EN 9
Downloaded From TheatreSystem-Manual.com Manuals
Note
•
You must connect this Home Theater System directly to a TV.
Option1: Connect to the SCART jack
1
Connect a composite video cable to the VIDEO jack on this Home Theater
System and the VIDEO input jack on the
TV.
Note
•
•
The video input jack on the TV might be labeled as A/V IN, VIDEO IN, COMPOSITE or
BASEBAND.
This type of connection provides standard picture quality.
SCART TO TV
Connect speakers and subwoofer
SCART
1
Connect a scart cable (not supplied) to the SCART TO TV jack on this Home
Theater System and the SCART input jack on the TV.
Note
•
•
Scart connection allows TV’s audio output through the speakers. Press AUDIO SOURCE repeatedly until ‘SCART IN’ is displayed on the display panel.
This type of connection provides good picture quality.
Option 2: Connect to the Video
(CVBS) jack
VIDEO
1
Connect the speakers and subwoofer to the matching jacks on this Home Theater
System.
Note
•
Ensure that the colors of the plugs and jacks are matched.
VIDEO IN
10 EN
Downloaded From TheatreSystem-Manual.com Manuals
Connect radio antenna
FM
(75 Ω)
ANTENNA
1
Connect the FM antenna to the FM75 jack on this Home Theater System
(for some models, this cable is already connected).
2
Extend the FM antenna and fi x its ends to the wall.
Tip
•
For better FM stereo reception, connect to an external FM antenna.
Connect audio cables/other devices
Route the audio from other devices to this
Home Theater System to enjoy audio play with multi-channel surround capabilities.
Connect audio from TV
AUX 1
AUDIO IN
AUDIO OUT
1
Connect the audio cables (not supplied) to the AUDIO IN-AUX1 jacks on this
Home Theater System and the AUDIO output jacks on the TV.
Note
•
To listen to the audio output from this connection, press AUDIO SOURCE repeatedly until ‘AUX1’ is displayed on the display panel.
EN 11
Downloaded From TheatreSystem-Manual.com Manuals
Connect audio from cable box/ recorder/game console
Connect USB device
AUX 2
AUDIO IN
AUDIO OUT
1
Connect the audio cables (not supplied) to the AUDIO IN-AUX2 jacks on this
Home Theater System and the AUDIO output jacks on the device.
Note
•
To listen to the audio output from this connection, press AUDIO SOURCE repeatedly until ‘AUX2’ is displayed on the display panel.
1
Connect the USB device to USB jack on this Home Theater System.
Note
•
•
This Home Theater System can only play/view
MP3, WMA, DivX (Ultra) or JPEG fi les that are stored on such devices.
Press USB to access the content and play the fi les.
Connect power cord
Warning
• Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the product.
1
Connect the power cord to the power outlet when all the required connections are done.
»
This product is ready to be set up for use.
12 EN
Downloaded From TheatreSystem-Manual.com Manuals
Navigate through the menu
Insert the remote control batteries
1
Point the remote control directly at the remote sensor on the product and select the desired function.
2
Press the following buttons on the remote control to navigate through the on-screen menus.
Button
OK
Action
Move up or down
Move left or right
Confi rm a selection
Enter numbers
1
Slide the battery cover off the back of the remote control.
2
Insert the 2 supplied batteries (AAA). Be sure the + and - ends of the batteries line up with the markings inside the case.
3
Slide the cover back into position.
Note
•
•
•
Do not mix batteries (old and new or carbon and alkaline, etc.).
Remove batteries if they are exhausted or if the remote control is not to be used for a long time.
Batteries contain chemical substances, they should be disposed of properly.
Control a play source
1
Press select the source you wish to control.
2
Select the desired function (for example
, ).
Find the correct viewing channel
1
Press
2
Press
3
Turn on the TV and switch to the correct video-in channel in one of the following ways:
• Go to the lowest channel on your
•
TV, then press the Channel Down button until you see the Philips screen.
Press SOURCE button repeatedly on the remote control of your TV.
EN 13
Downloaded From TheatreSystem-Manual.com Manuals
Tip
•
The video-in channel is between the lowest and highest channels and may be called
FRONT, A/V IN, VIDEO, HDMI etc. See the
TV user manual on how to select the correct input on the TV.
Select menu display language
General Setup
Disc Lock
Display Dim
OSD Language
Screen Saver
Sleep Timer
DivX(R) VOD Code
English
Français
Deutsch
Italiano
Español
Português
Nederlands
Dansk
1
Press
2
Press
» [General Setup] menu is displayed.
3
Press
4
Press the menu, then press .
• The language options are different depending on your country or region. It may not correspond to the illustration shown here.
5
Press
OK.
Tip
•
You can set the default language for DVD disc menu (see ‘Adjust settings’ > ‘Preference’ >
[Disc Menu]).
Change speaker settings
Ideally, the distance between listening position and all the speakers should be the same. If not, change the speaker settings based on their distance from the listening position to obtain the best possible surround sound.
Audio Setup
Speakers Volume
Speakers Delay
Night Mode
CD Upsampling
1
Press
2
Press
3
Press menu, then press .
• If the speaker setup option is not accessible, press twice before you press SETUP.
To set the speakers level
1
Select then press .
Speakers Volume Setup
Front Left
Front Right
Center
Subwoofer
Rear Left
Rear Right
2
Press then press OK.
»
The test tone is emitted from the speaker.
0dB
0dB
0dB
0dB
0dB
0dB
14 EN
Downloaded From TheatreSystem-Manual.com Manuals
•
•
Repeat the above setting for other speakers until all the speakers output level sounds equally balance.
To exit the menu, press SETUP.
To set the output delay time (center and rear speakers only)
1
Select then press .
Speakers Distance Setup
Center
Rear Left
Rear Right
0MS
0MS
0MS
2
Press
OK.
• Repeat the above setting for other
• speakers until the sound output from different speakers reach the listening position at the same time.
To exit the menu, press SETUP.
Tip
•
•
Set a longer delay time if the center speaker or rear speaker is closer to the listening position than the front speaker.
Allow 1ms setting for every 1 foot distance between the speaker and the listening position.
Select a play source
On the main unit
• Press SOURCE button repeatedly to select: DISC > USB > FM > AUX 1 >
AUX 2 > SCART IN > DISC ...
On the remote control
•
•
•
•
Press AUDIO SOURCE repeatedly to switch to the connected audio source.
Display
SCART IN
AUX 1
AUX 2
Device connected to
SCART TO TV jack
AUDIO IN-AUX 1 jacks
AUDIO IN-AUX 2 jacks
Press RADIO to switch to FM band.
Press USB to switch to USB mode.
Press DISC to switch to disc mode.
EN 15
Downloaded From TheatreSystem-Manual.com Manuals
5 Play
Play a disc
Caution
•
•
Never place any objects other than discs into the disc compartment.
Never touch the disc optical lens inside the disc compartment.
1
Press to open the disc compartment.
2
Insert a disc with its label facing up.
• For double-sided disc, load the side to play faces up.
3
Press to close the disc compartment and start disc play.
•
•
To view disc play, turn on the TV to the correct viewing channel for this
Home Theater System.
To stop disc play, press .
Note
•
•
•
•
Check the types of discs supported (see
‘Specifi cations’ > ‘Playback media’).
If the password entry menu is displayed, enter the password before you can play the locked or restricted disc.
If you pause or stop a disc for about 15 minutes, the screen saver activates. To deactivate the screen saver, press DISC.
After you pause or stop a disc and no buttons are pressed within 30 minutes, this Home
Theater System automatically switches to standby mode.
Play video
Note
•
For video disc, playback always resumes from the point where it was last stopped. To start play from the beginning, press while the message is displayed.
Control video play
1
Play a title.
2
Use the remote control to control the title.
Button
/
/
Action
Starts, pauses or resumes playback.
Stops play.
Skips to the next title or chapter.
Skips to the beginning of the current title or chapter. Press twice to jump to the previous title or chapter.
Searches fast-forward (right) or fast-backward (left). Press repeatedly to change the search speed.
Searches slow-forward (down) or slow-backward (up). Press repeatedly to change the search
• speed.
For VCD, only slow-forward play is possible.
16 EN
Downloaded From TheatreSystem-Manual.com Manuals
Change video play
1
Play a title.
2
Use the remote control to change the video play.
Button Action
AUDIO
SYNC
Selects an audio language or channel.
SUBTITLE Selects a subtitle language for video.
REPEAT Selects or turns off repeat or
• shuffl e mode.
Repeat options vary
• depending on the disc type.
For VCDs, repeat play is only possible if the PBC mode is turned off.
ZOOM Zooms in or out of the picture.
• To pan through the zoomed image, press the Navigation buttons.
INFO Displays the current status or the disc information.
• You can change the video play options here without interrupting playback.
SCREEN
FIT
•
Fits the picture format to the TV screen (using zoom factor 1.3X and 1.6X).
It is only applicable to DVD and JPEG fi les, not available for DivX movie.
Note
• Some operations may not work with some discs. See the information accompanying the disc for details.
Access DVD menu
1
Press
2
Select a play option, then press OK.
• In some menus, press the Numeric
• buttons to input your selection.
To return to the title menu during play, press BACK.
Access VCD menu or preview menu
The PBC (Playback Control) for VCD is activated by default in the factory. When you load in a VCD, the contents menu is displayed.
1
Press select a play option, then press OK to start play.
• If PBC is off, it skips the menu and starts play from the fi rst title.
• To return to the menu during play, press BACK (only possible if the
PBC mode is on).
2
Press the disc.
• To exit the menu, press DISC.
Select Digest Type:
Track Digest
Disc Interval
Track Interval
3
Select a preview play option, then press
OK
EN 17
Downloaded From TheatreSystem-Manual.com Manuals
[Track Digest]
Plays the fi rst few seconds of each track in a disc.
[Disc Interval]
Divides the total disc time by six and play the fi rst few seconds of these intervals.
[Track Interval]
Divides the current track by six and play the fi rst few seconds of these intervals.
This option is not available in stop mode.
Tip
•
You can change the PBC setting (see ‘Adjust settings’ > ‘Preference’ > [PBC]).
Sync audio output with video play
If the video play is slower than the audio output (sound does not match with the pictures), you can delay the audio output to match the video.
Repeat play a specifi c section
1
During play, press REPEAT A-B at where you want to set the starting point.
2
Press ending point.
»
Repeat play starts.
3
To cancel repeat play, press REPEAT A-B again.
Note
•
The marked section for repeat play is only possible within a track/title.
View video play from different camera angles
1
During play, press ANGLE repeatedly to display the angle options.
»
Play changes to the selected angle.
Note
•
Applicable only to discs contain multi-angle scenes.
Quick skip play to a specifi c time
1
Press and hold AUDIO SYNC until
‘AUDIO SYNC XXX’ is displayed. ‘XXX’ denotes the delay time.
2
Within fi ve seconds, press VOL +/- to set the delay time for audio output.
Note
•
If the volume control is not used within 5 seconds, it resumes normal volume control function.
1
During play, press INFO.
»
The disc status menu is displayed.
2
Press
OK.
• [TT Time] (title time)
• [Ch Time] (chapter time)
• [Disc Time] (disc time)
• [Track Time] (track time)
3
Press the Numeric buttons to enter the time where you want to skip to, then press OK.
18 EN
Downloaded From TheatreSystem-Manual.com Manuals
Note
•
The options are different depending on the disc type.
Play DivX® video
DivX video is a digital media format that retains high quality despite a high rate of compression. You can enjoy DivX video on this DivX® Certifi ed product.
1
Insert a disc or USB that contains the
DivX videos.
2
Press
»
A contents menu is displayed.
3
Select a title to play, then press .
4
Use the remote control to control the title.
Button Action
AUDIO
SYNC
Selects an audio language or channel.
SUBTITLE Selects a subtitle language for video.
INFO
Stops play.
For DivX Ultra video, press this button again to display the contents menu.
Displays DivX Ultra video information.
Note
•
•
•
•
You can only play DivX videos that were rented or purchased with the DivX registration code of this Home Theater System
(see ‘Adjust settings’ > ‘General setup’ >
[DivX(R) VOD Code]) .
You can play DivX video fi les of up to 4GB.
If the subtitle does not appear correctly, change the character set (see ‘Adjust settings’
> ‘Preference’ > [DivX Subtitle]).
This Home Theater System can display up to
45 characters in the subtitle.
Play music
Control audio track play
1
Play a track.
2
Use the remote control to control the track.
Button Action
Starts, pauses or resumes playback.
Stops play.
Skips to the next track.
Skips to the beginning of the current track. Press twice to jump to the previous track.
Selects an item to play.
/
REPEAT
Searches fast-forward
(right) or fast-backward
(left). Press repeatedly to change the search speed.
Selects or turns off repeat or shuffl e mode.
Play MP3/WMA music
MP3/WMA is a type of highly compressed audio fi le (fi les with .mp3 or .wma extensions).
1
Insert a disc or USB that contains the
MP3/WMA music.
2
Press
»
A contents menu is displayed.
3
Select a folder, then press OK.
4
Select a track to play, then press .
• To return to the main menu, press
BACK or press until ‘Previous’ folder is selected, then press OK.
EN 19
Downloaded From TheatreSystem-Manual.com Manuals
Note
•
•
•
•
•
For disc recorded in multiple sessions, only the fi rst session is played.
This product does not support MP3PRO audio format.
If any special characters are present in the MP3 track name (ID3) or album name, it might not be displayed correctly on the screen because these characters are not supported.
Some WMA fi les are protected by Digital
Rights Management and cannot be played on this product.
Folders/fi les that exceed the supported limit of this product will not be displayed or played.
Tip
•
You can select the display of data contents, view folders or fi les (see ‘Adjust settings’ >
‘Preference’ > [MP3/JPEG Display]).
Play photo
Play photo as slideshow
This product can play JPEG photos (fi les with
.jpeg or .jpg extensions).
1
Insert a disc or USB that contains the
JPEG photos.
2
Press
»
Slideshow begins (for Kodak disc) or a contents menu (for JPEG disc) is displayed.
3
Select the folder/album you want to play.
• To preview the photos in the folder/ album, press INFO.
•
•
To go to previous or next screen display, press / .
To select a photo, press the
Navigation buttons.
• To display the selected photo only,
• press OK.
4
Press
To return to the menu, press
BACK.
Note
•
•
•
•
You may require longer time to display the disc content on the TV due to the large number of songs/photos compiled onto one disc.
If the JPEG photo is not recorded with an ‘exif ’ type fi le, the actual thumbnail picture is not be shown on the display. It is replaced by a ‘blue mountain’ thumbnail picture.
This product can only display digital camera pictures according to the JPEG-EXIF format, typically used by almost all digital cameras.
It cannot display Motion JPEG and pictures in formats other than JPEG, or sound clips associated with pictures.
Folders/fi les that exceed the supported limit of this product will not be displayed or played.
Control photo play
1
Play photo slideshow.
2
Use the remote control to control the photo.
Button
ZOOM
Action
Skips to the previous photo.
Skips to the next photo.
Rotates the photo clockwise.
Rotates the photo anticlockwise.
Zooms in or out of the picture.
Play pause in zoom mode.
Stops play.
20 EN
Downloaded From TheatreSystem-Manual.com Manuals
Play musical slideshow
Play MP3/WMA music fi les and JPEG photo fi les simultaneously to create musical slideshow. The MP3/WMA and JPEG fi les must be stored on the same disc or USB device.
1
Play MP3/WMA music.
2
Navigate to the photo folder/album and press OK to start slideshow play.
»
Slideshow begins and continues till the end of the photo folder or album.
»
Audio continues to play till the end of the disc.
•
•
To stop slideshow play, press
To stop music play, press
.
again.
Play from USB device
This product plays/views MP3, WMA, DivX
(Ultra) or JPEG fi les on the following USB devices:
• fl ash drive
• memory card reader
• HDD (external power source needed)
4
To stop play, press or remove the USB device.
Note
•
•
•
If the device does not fi t into the USB jack, connect it through a USB extension cable.
If you connect a multiple USB card/device reader, only one card/device can be accessed.
Digital cameras that need PC software or use
PTP protocol are not supported.
Play from radio
Check if the FM antenna has been connected to this Home Theater System. If not, connect the supplied FM antenna to the FM75 jack and fi x its ends to the wall.
FM
(75 Ω)
ANTENNA
Tip
•
•
For the best reception, place the antenna away from your TV or other sources of radiation.
For even better reception of FM stereo, connect an external FM antenna (not supplied).
1
Connect a USB storage device to the
(USB) jack.
2
Press
»
A contents menu is displayed.
3
Select a fi le to play, then press .
»
Play starts.
EN 21
Downloaded From TheatreSystem-Manual.com Manuals
First time tuning
When you access to radio mode for the fi rst time, follow the instruction to install the radio stations.
1
Press
»
’AUTO INSTALL ... PRESS PLAY’ is displayed.
2
Press
»
All detected radio stations are stored.
»
Once complete, it tunes to the fi rst preset radio station.
• To stop auto tuning, press .
Note
•
•
This Home Theater System can store up to a maximum of 40 radio stations.
If auto installation is not activated or less than 5 radio stations are stored, you will be prompted to install the radio stations again.
Listen to radio
1
Press
2
Use the remote control to control the radio.
Button Action
Selects a preset radio station.
Tunes the radio frequency up or down.
Press and hold this button to erase the current radio station
• from the preset list.
The preset number for other radio stations remain unchanged.
Reinstall all the radio stations
1
Press
2
Press and hold PROGRAM for more than
5 seconds.
»
All previously stored radio stations are replaced.
Note
• Check the radio antenna connection if no stereo signal is detected or less than 5 stations are detected during radio installation.
Search and store radio stations individually
1
Press
2
Press .
»
It starts searching until a radio station is detected.
3
Repeat step 2 until you tune to the radio station you wish to store.
• To fi netune the radio frequency, press / .
4
Press
»
The preset station number blinks.
»
If no action is carried out within 20 seconds after the above step, it exits the preset mode.
5
Press / (or the Numeric buttons) to select a preset number to store.
6
Press
22 EN
Downloaded From TheatreSystem-Manual.com Manuals
Select a preset sound
Control the volume
1
Press the volume.
•
•
To mute, press .
To restore the volume, press or press VOL +.
again
Select surround sound
1
Press surround output that’s available on the disc.
Option
5 CH
STEREO
MULTI-
CHANNEL
/ DPLII
STEREO
Description
Enhances the stereo channel output by duplicating the sound output to the center and rear speakers. Ideal for party music.
Multi-channel surround output: Dolby Digital, and
Dolby Pro Logic II.
Stereo sound
Note
•
“Dolby Prologic II” 5-channel mode is the default surround mode whenever you turn on this Home Theater System or change to other play source.
1
Press sound effect that most suitable for the video or music you play.
Video/Music Description
ACTION /
ROCK
CONCERT/
CLASSIC
DRAMA /
JAZZ
SPORTS
NIGHT
Enhanced low and high range for great sounding movie effects and atmosphere. Great for action movies and rock/ pop music.
Flat and pure sound mode.
Ideal for listening to classical music and watching live concert disc.
Clear mid and high range.
Recreates the atmosphere of a live club with the artist just in front of you. Good for jazz music and watching dramas.
Moderate mid range and surround effects for clear vocals and the atmosphere of a live sports venue. It is also ideal for video gaming.
Dynamically controlled sound mode suitable for watching movies at night or for nonintrusive background music.
EN 23
Downloaded From TheatreSystem-Manual.com Manuals
You can customize various kinds of settings as you prefer. Refer to the following instructions to navigate through the setup menus.
Symbol Options
[General Setup]
[Audio Setup]
[Video Setup]
[Preference]
3
Select an option, then press OK.
4
Select a setting, then press OK.
• To return to the previous menu,
• press BACK.
To exit the menu, press SETUP.
Note
•
See the explanations of the above options in the following pages.
[Disc Lock]
Sets play restriction for a specifi c discs.
Before you start, place the disc in the disc compartment (maximum 40 discs can be locked).
• [Lock] – Restricts access to the current disc. Once activated, a password is needed to unlock and play the disc.
• [Unlock] – Plays all discs.
Tip
•
You can set or change the password (see
‘Adjust settings’ > ‘Preferences’ > [Password]).
Note
• If the setup option is grayed out, it means the setting cannot be changed at the current state.
General setup
1
2
General Setup
Disc Lock
Display Dim
OSD Language
Screen Saver
Sleep Timer
DivX(R) VOD Code
Press
» [General Setup] menu is displayed.
Press
[Display Dim]
Changes the brightness level of the display panel on this Home Theater System.
• [100%] – Normal brightness.
• [70%] – Medium brightness.
• [40%] – Dimmest display.
[OSD Language]
Selects the default on-screen menu language.
[Screen Saver]
Turns off or on the screen saver mode. Helps to protect the TV screen from being damaged due to over exposure to a static image for too long.
• [On] – Sets the screen saver to appear after 15 minutes of inactivity (for example, in pause or stop mode).
• [Off] – Disables screen saver mode.
24 EN
Downloaded From TheatreSystem-Manual.com Manuals
[Sleep Timer]
Switches to standby automatically after the preset time.
• [15 mins], [30 mins], [45 mins], [60 mins]
– Selects the count down time before the Home Theater System switches to standby.
• [Off] – Disables sleep timer mode.
[DivX(R) VOD Code]
Displays the DivX® registration code.
Tip
•
Enter this Home Theater System DivX registration code when you rent or purchase video from www.divx.com/vod. The DivX videos rented or purchased through the
DivX® VOD (Video On Demand) service can be played only on the device to which it is registered.
Audio setup
1
Audio Setup
Speakers Volume
Speakers Delay
Night Mode
CD Upsampling
Press
» [General Setup] menu is displayed.
2
Press press .
3
Select an option, then press OK.
4
Select a setting, then press OK.
• To return to the previous menu,
• press BACK.
To exit the menu, press SETUP.
Note
•
See the explanations of the above options in the following pages.
[Speakers Volume]
Sets the volume level of each speaker to get the ideal audio balance.
1) To start, press OK.
2) Select a speaker in the menu, then press
to adjust the volume level.
3) Press OK to confi rm and exit.
Note
• The test tone is emitted from the speaker which you adjust.
[Speakers Delay]
Sets the delay time for the center and rear speakers if they are placed closer to the listening position, so that the sound output from all speakers reach the listening position at the same time.
1) To start, press OK.
2) Select a speaker in the menu, then press
to set the delay time.
3) Press OK to confi rm and exit.
Note
• Allow 1ms setting for every 1 foot distance between the speaker and the listening position.
[Night Mode]
Makes loud sound level softer and soft sound level louder so that you can watch the DVD movies at a low volume, without disturbing others.
• [On] – Enjoys quiet viewing at night.
• [Off] – Enjoys surround sound with a full dynamic range.
EN 25
Downloaded From TheatreSystem-Manual.com Manuals
Note
•
Applicable only to Dolby Digital encoded discs.
[TV Display]
Selects one of the following display formats:
Video setup
Video Setup
TV System
TV Display
Picture Settings
1
Press
» [General Setup] menu is displayed.
2
Press press .
3
Select an option, then press OK
4
Select a setting, then press OK.
• To return to the previous menu,
• press BACK.
To exit the menu, press SETUP.
Note
•
See the explanations of the above options in the following pages.
[TV System]
Changes this setting if the video does not appear correctly. By default, this setting matches the most common setting for TVs in your country.
• [PAL] – For PAL-system TV.
• [NTSC] – For NTSC-system TV.
• [Multi] – For TV that is compatible with both PAL and NTSC.
4:3 Pan Scan (PS)
4:3 Letter Box (LB) 16:9 (Wide Screen)
• [4:3 Pan Scan] – For 4:3 screen TV: fullheight display with the trimmed sides.
• [4:3 Letter Box] – For 4:3 screen TV: wide-screen display with black bars on the top and bottom of the screen.
• [16:9 Wide Screen] – For wide-screen
TV: display ratio 16:9.
[Picture Settings]
Selects a predefi ned set of picture color settings or customize the personal setting.
• [Standard] – Original color setting.
• [Bright] – Vibrant color setting.
• [Soft] – Warm color setting.
• [Personal] – Customizes the color setting.
Set the level of brightness, contrast, sharpness/tint and color saturation, then press OK.
26 EN
Downloaded From TheatreSystem-Manual.com Manuals
Preference
Note
•
Stop disc play before you can access to
[Preference].
Preference
Audio
Subtitle
Disc Menu
Parental
PBC
MP3/JPEG Display
Password
DivX Subtitle
1
Press
» [General Setup] menu is displayed.
2
Press
.
3
Select an option, then press OK.
4
Select a setting, then press OK.
• To return to the previous menu, press BACK.
• To exit the menu, press SETUP.
Note
•
See the explanations of the above options in the following pages.
Note
•
•
•
If the language you have set is not available on the disc, the disc uses its own default language.
For some discs, the subtitle/audio language can only be changed from the disc menu.
To select the languages that are not listed in the menu, select [Others]. Then check the Language Code list at the back of this user manual and enter the respective 4-digit language code.
[Parental]
Restricts access to discs that are unsuitable for children. These types of discs must be recorded with ratings.
1) Press OK.
2) Select a rating level, then press OK.
3) Press the Numeric buttons to enter the password.
Note
•
•
•
Rated discs above the level you set in
[Parental] require a password to be played.
The ratings are country-dependent. To allow all discs to play, select ‘ 8’.
Some discs have ratings printed on them but are not recorded with ratings. This function has no effect on such discs.
Tip
• You can set or change the password (see
‘Preference’ > [Password]).
[Audio]
Selects the default audio language for disc play.
[Subtitle]
Selects the default subtitle language for disc play.
[Disc Menu]
Selects the language for disc menu.
[PBC]
Turns off or on the content menu of VCDs/
SVCDs with PBC (playback control) feature.
• [On] - Displays index menu when you load a disc for play.
• [Off] - Skips the menu and start play from the fi rst title.
EN 27
Downloaded From TheatreSystem-Manual.com Manuals
[MP3/JPEG Display]
Selects to display the folders or display all the fi les.
• [View Folders] – Displays the folders of
MP3/WMA fi les.
• [View Files] – Displays all the fi les.
[Password]
Sets or changes the password for locked discs and play restricted DVDs.
Change Password
Old Password
New Password
Confirm Password
OK
1) Press the Numeric buttons to enter
‘136900’ or the last set password at [Old
Password] fi eld.
2) Enter the new password at [New
Password] fi eld.
3) Enter the new password again at [Confi rm
Password] fi eld.
4) Press OK to exit the menu.
Note
• If you forget the password, enter ‘136900’ before you set a new password.
[DivX Subtitle]
Selects a character set that supports the DivX subtitle.
[Standard] English, Irish, Danish, Estonian,
Finnish, French, German, Italian,
Portuguese, Luxembourgish,
Norwegian (Bokmål and
Nynorsk), Spanish, Swedish,
Turkish
[Central
Europe]
Polish, Czech, Slovak, Albanian,
Hungarian, Slovene, Croatian,
Serbian (Latin script), Romanian
[Cyrillic] Belarusian, Bulgarian, Ukrainian,
Macedonian, Russian, Serbian
[Greek] Greek
Note
• Ensure that the subtitle fi le has the exact same fi le name as the movie fi le. If for example the fi le name of the movie is ‘Movie.avi’, then you will need to name the text fi le ‘Movie.sub’ or
‘Movie.srt’.
[Version Info.]
Displays the software version of this Home
Theater System.
Tip
•
This information is required when you want to fi nd out if a newest software version is available at the Philips website that you may download and install on this Home Theater
System.
[Default]
Resets all the settings of this Home Theater
System to factory default, except for [Disc
Lock], [Password] and [Parental] settings.
28 EN
Downloaded From TheatreSystem-Manual.com Manuals
8 Additional
Information
Update software
To check for new updates, compare the current software version of your Home Theater System with the latest software version (if available) at the Philips website.
Preference
Disc Menu
Parental
PBC
MP3/JPEG Display
Password
DivX Subtitle
Version Info.
Default
1
Press
2
Select then press OK.
3
Write down the version number, then press SETUP to exit the menu.
4
Go to www.philips.com/support to check the latest software version available for this Home Theater System.
5
If the latest software version is higher than the software version of this Home
Theater System, download it and store onto a CD-R or USB fl ash drive.
6
Insert the CD-R or USB fl ash drive to this
Home Theater System.
7
Press instruction on the TV to confi rm update operation.
»
Once software update is complete, this Home Theater System turns off to standby automatically.
Note
•
Do not remove the CD-R or USB when software updating is in progress.
8
Disconnect the power cord for a few seconds and connect again to reboot the system.
Care
Caution
•
Never use solvents such as benzene, thinner, cleaners available commercially, or anti-static sprays intended for discs.
Clean discs
Wipe the disc with a micro fi bre cleaning cloth from the centre to the edge in a straight line movement.
Clean main unit screen
Wipe the screen surface with a micro fi bre cleaning cloth.
EN 29
Downloaded From TheatreSystem-Manual.com Manuals
9 Specifications
Note
• Specifi cation and design are subject to change without notice
Playback media
• DVD-Video, DVD+R/+RW, DVD-R/-
RW, DVD+R DL, CD-R/CD-RW, Audio
CD, Video CD/SVCD, Picture CD, MP3-
CD, WMA-CD, DivX-CD, USB fl ash drive
•
•
Amplifi er
• Total output power: 300 W RMS (30% THD)
Frequency response: 180 Hz~18kHz / ±3dB
Signal-to-noise ratio: > -60 dB (A-weighted)
• Input sensitivity:
• AUX: 500 mV
• SCART TO TV: 500 mV
•
•
•
•
•
•
•
•
•
Disc
• Laser Type: Semiconductor
Disc diameter: 12cm / 8cm
Video decording: MPEG1/ MPEG2 / DivX
/ DivX Ultra
Video DAC: 12 bits, 108 MHz
Signal system: PAL / NTSC
Video S/N: 56 dB
Audio DAC: 24 bits / 96 kHz
Frequency response:
• 4 Hz - 20 kHz (44.1 kHz)
• 4 Hz - 22 kHz (48 kHz)
• 4 Hz - 44 kHz (96 kHz)
PCM: IEC 60958
Dolby Digital: IEC 60958, IEC 61937
•
•
•
•
•
Radio
Tuning range: FM 87.5-108 MHz (50 kHz)
26 dB quieting sensitivity: FM 22 dBf
IF rejection ratio: FM 50 dB
Signal-to-noise ratio: FM 30 dB
Harmonic distortion: FM 3%
30 EN
Downloaded From TheatreSystem-Manual.com Manuals
•
•
•
Frequency response: FM 180 Hz~10 kHz
/ ±6dB
Stereo separation: FM 26 dB (1 kHz)
Stereo Threshold: FM 23.5 dB
USB
• Compatibility: USB
• Class support: UMS (USB Mass Storage
•
Class)
File system: FAT12, FAT16, FAT32
•
•
•
Main Unit
• Power supply: 220-240V; ~50 Hz
•
Power consumption: 60 W
Standby power consumption: < 1 W
Dimensions (WxHxD): 360 x 55 x 332
(mm)
Weight: 2.64 kg
•
•
•
Speakers
• System: full range satellite
• Speaker impedance: 8 ohm (center), 4
• ohm (Front/Rear)
Speaker drivers: 3” full range
Frequency response: 150 Hz - 20 kHz
Dimensions (WxHxD): 100 x 100 x 75
(mm)
Weight: 0.38 kg/each
•
•
•
•
Subwoofer
Impedance: 8 ohm
Speaker drivers: 165 mm (6.5”) woofer
•
Frequency response: 45 Hz ~ 150 Hz
Dimensions (WxHxD): 122.6 x 309.5 x
369 (mm)
Weight: 3.54 Kg
•
•
Laser specifi cation
Type: Semiconductor laser GaAIAs (CD)
Wave length: 645 - 665 nm (DVD), 770
•
•
- 800 nm (CD)
Output power: 6 mW (DVD), 7 mW
(VCD/CD)
Beam divergence: 60 degrees.
10 Troubleshooting
Warning
• Risk of electric shock. Never remove the casing of the product.
To keep the warranty valid, never try to repair the product yourself.
If you have problems using this product, check the following points before you request service.
If you still have a problem, register your product and get support at www.philips.com/welcome.
If you contact Philips, you will be asked for the model and serial number of your product. The model number and serial number are on the back or bottom of your product. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
•
The buttons on this product do not work.
Disconnect this product from the power outlet for a few minutes, then connect again.
Picture
•
•
•
No picture.
See TVs manual for correct video input channel selection. Change the TV channel until you see the DVD screen.
Press DISC.
If you have changed the [TV System] setting, switch back to default mode: 1)
Press to open the disc compartment. 2)
Press . 3) Press SUBTITLE.
Sound
No sound.
• Make sure that the audio cables are connected and select the correct input source (for example, AUDIO SOURCE,
USB) for the device you want to play.
• If this Home Theater System does not support DTS surround sound, ensure that the play source is not from DTS audio stream.
No sound from TV program.
• Connect an audio cable from the AUDIO input on this Home Theater System to the AUDIO output on your TV. Then press AUDIO SOURCE repeatedly to select the corresponding audio input source.
•
•
•
No surround sound effect from the speakers.
Press SURR to select a correct surround sound setting.
If the Home Theater System supports
DTS playback, press AUDIO SYNC to select other audio track.
Ensure that the source you are playing is recorded or broadcast in surround sound
(Dolby Digital, etc).
EN 31
Downloaded From TheatreSystem-Manual.com Manuals
Play
•
•
DivX video fi les cannot be played.
Make sure that the DivX fi le is encoded according to the ‘Home Theater Profi le’ with the DivX encoder.
Make sure that the DivX video fi le is complete.
The aspect ratio of the screen is not aligned with the TV display setting.
• The aspect ratio is fi xed on the disc.
•
•
DivX subtitle does not display correctly.
Ensure that the subtitle fi le name is the same as the movie fi le name.
Select the correct character set: 1) Press
SETUP. 2) Select [Preference], then press . 3) Select [DivX Subtitle], then press OK. 4) Select the character set that supports the subtitle.
•
•
•
The contents of the USB fl ash drive cannot be read.
The USB fl ash drive format is not compatible with this Home Theater
System.
Drive is formatted with different fi le system which is not supported by this unit (e.g. NTFS).
Maximum size of memory supported is
160GB.
32 EN
Downloaded From TheatreSystem-Manual.com Manuals
11 Glossary
A
Aspect ratio
Aspect ratio refers to the length to height ratio of TV screens. The ratio of a standard
TV is 4:3, while the ratio of a high-defi nition or wide TV is 16:9. The letter box allows you to enjoy a picture with a wider perspective on a standard 4:3 screen.
D
DivX Video
DivX® is a digital video format created by
DivX, Inc. This is an offi cial DivX Certifi ed device that plays DivX video. Visit www.divx.
com for more information and software tools to convert your fi les into DivX video.
DivX Video-On-Demand
This DivX Certifi ed ® device must be registered in order to play DivX Video-on-
Demand (VOD) content. To generate the registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about
DivX video.
Dolby Digital Pro Logic II
An advanced, matrix decoding technology that expands any two channel audio, such as CDs and stereo encoded videocassettes, video games and TV broadcasts to a fi ve channel full bandwidth (range) playback (Left/Center/
Right/Left Surround/Right Surround), resulting in a surround sound experience.
J
JPEG
A very common digital still picture format.
A still-picture data compression system proposed by the Joint Photographic Expert
Group, which features small decrease in image quality in spite of its high compression ratio.
Files are recognized by their fi le extension
‘.jpg’ or ‘.jpeg.’
M
MP3
A fi le format with a sound data compression system. MP3 is the abbreviation of Motion
Picture Experts Group 1 (or MPEG-1) Audio
Layer 3. With the MP3 format, one CD-R or
CD-RW can contain about 10 times more data than a regular CD.
MPEG
Motion Picture Experts Group. A collection of compression systems for digital audio and video.
P
PBC
Playback Control. A system where you navigate through a Video CD/Super VCD with on-screen menus that are recorded onto the disc. You can enjoy interactive playback and search.
PCM
Pulse Code Modulation. A digital audio encoding system.
W
WMA
Windows Media™ Audio. Refers to an audio compression technology developed by
Microsoft Corporation. WMA data can be encoded with Windows Media player version
9 or Windows Media player for Windows XP.
Files are recognized by their fi le extension
‘.wma.’
EN 33
Downloaded From TheatreSystem-Manual.com Manuals
34 EN
Downloaded From TheatreSystem-Manual.com Manuals
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project