Access Control
GV-ASManager
User's Manual V4.2.1
ASMV421-A-EN
© 2014 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows XP
are registered trademarks of Microsoft Corporation.
May 2014
Contents
Note for Users Upgrading GV-ASManager ............................................................ vi
Software Compatibility.......................................................................................... viii
Chapter 1 Introduction........................................................................................... 1
1.1 Main Features ......................................................................................... 2
1.2 Concepts................................................................................................. 4
1.3 Optional Devices ..................................................................................... 6
Chapter 2
Installation............................................................................................. 7
2.1 System Requirements ............................................................................. 7
2.2
Installing the GV-ASManager .................................................................. 8
2.3 Logging in ............................................................................................... 9
Chapter 3
The Main Screen of GV-ASManager.................................................. 11
3.1 Main Screen...........................................................................................11
3.1.1 Toolbar......................................................................................12
3.2 Device View ...........................................................................................14
3.2.1
3.3
Chapter 4
Controls on the Window ............................................................14
Monitoring Windows...............................................................................16
3.3.1
Controls on the Window ............................................................16
3.3.2
Customizing a Monitoring Window ............................................17
3.3.3
Arranging Monitoring Windows..................................................18
Settings ............................................................................................... 19
4.1 Setup Flowchart .....................................................................................19
4.2 Adding Controllers..................................................................................20
4.2.1 Step 1: Configuring a Controller ................................................20
4.2.2 Step 2: Configuring the Doors or Elevator Floors ......................23
4.3 Setting Cards .........................................................................................31
4.3.1 Adding a Single Card ................................................................31
4.3.2 Adding a Group of Cards...........................................................35
4.3.3 Importing/Exporting Card Data ..................................................35
4.4 Setting Weekly Schedules......................................................................37
4.4.1
Step 1: Setting Time Zones .......................................................37
4.4.2
Step 2: Setting Weekly Schedules.............................................39
4.4.3 Step 3: Setting Holidays ............................................................41
4.5 Setting Access Groups...........................................................................42
4.6 Setting Users .........................................................................................44
4.6.1 Adding a User ...........................................................................44
4.6.2 Assigning a Card to a User........................................................45
4.6.3 Sending SMS Alerts ..................................................................45
i
4.6.4 Customizing a Data Field ..........................................................45
4.6.5 Importing/Exporting User Data ..................................................47
Chapter 5
Video Integration ................................................................................ 48
5.1 Mapping Cameras..................................................................................48
5.2 Accessing a Live View............................................................................50
5.2.1
5.3
Live Video Window....................................................................51
Accessing a Video Image.......................................................................52
5.4 The MultiView Window ...........................................................................52
5.4.1 Adding a Matrix View.................................................................54
5.5 Retrieving Recorded Video ....................................................................55
Chapter 6
Anti-Passback..................................................................................... 57
6.1 Anti-Passback ........................................................................................58
6.2 Local Anti-Passback...............................................................................59
6.3 Global Anti-Passback .............................................................................61
6.3.1
Step 1: Enabling Global Anti-Passback .....................................61
6.3.2 Step 2: Configuring Areas .........................................................62
6.3.3
Step 3: Configuring Readers .....................................................62
6.3.4 Step 4: Configuring Door Contacts ............................................63
6.3.5 Step 5: Locating Users ..............................................................64
Chapter 7
Patrol Tour .......................................................................................... 65
7.1 Creating Patrol Tour ...............................................................................65
7.2 Activating the Patrol Tour .......................................................................68
7.3 Monitoring Patrol Activities .....................................................................70
7.4 Accessing Patrol Log..............................................................................71
Chapter 8
Other Functions.................................................................................. 72
8.1 Setting Up System User .........................................................................72
8.1.1 Adding a New User ...................................................................72
8.1.2 Editing an Exiting User ..............................................................74
8.2 Setting Up Alert Notification....................................................................75
8.2.1 Setting SMS Server...................................................................75
8.2.2 Setting E-Mail Server ................................................................76
8.2.3 Setting Notification ....................................................................77
8.3 Startup, Backup and Export Setup .........................................................79
8.4
Setting Up GV-GF Fingerprint Readers..................................................81
8.5
Scanning Driver’s Licenses and Business Card .....................................82
8.6 Setting Hot Keys to Quickly Control Doors .............................................84
8.7 Defining New Card Formats ...................................................................85
Chapter 9
GV-ASRemote ..................................................................................... 87
9.1 Installing GV-ASRemote ........................................................................87
ii
9.2 The GV-ASRemote Window...................................................................87
9.2.1 Toolbar......................................................................................89
9.3
Chapter 10
Connecting to GV-ASManager ...............................................................90
GV-ASWeb......................................................................................... 92
10.1
Connecting to GV-ASManager .............................................................92
10.2 Accessing Live Video ...........................................................................95
10.3 Accessing Logs ....................................................................................96
10.3.1 Setting Search Criteria ............................................................96
10.3.2 Log Window Icons ...................................................................97
10.3.3 Exporting Logs ........................................................................97
10.3.4 Defining Columns ....................................................................97
10.4 Adding and Deleting Controllers...........................................................99
10.5 Adding and Deleting Cards and Users ...............................................100
10.6
Searching, Adding and Deleting IP Cameras .....................................104
10.7 Setting Schedule ................................................................................106
10.7.1
Setting Daily Schedule ..........................................................106
10.7.2
Setting Weekly Schedule.......................................................107
10.7.3 Specifying Holiday.................................................................108
10.8 Setting Access Groups.......................................................................108
10.9 Setting Door Groups...........................................................................109
10.10 Configuring Areas for Anti-Passback................................................110
10.11 Creating Maps..................................................................................111
10.12
Chapter 11
Creating Accounts to Manage GV-ASWeb .......................................114
GV-TAWeb for Workforce Schedule and Payroll ......................... 116
11.1
Connecting to GV-ASManager ...........................................................117
11.2 Setting Up Workforce Schedule .........................................................119
11.2.1 TA Shift: Setting Up a Daily Schedule ...................................119
11.2.2 TA Template: Setting Up a Schedule Template.....................122
11.2.3 TA Holidays: Setting Certain Dates as Holidays ....................123
11.2.4 TA Schedule: Assigning Schedules to Employees.................124
11.3 TA User: Specifying Hourly Pay .........................................................128
11.4 TA Report: Looking Up Records.........................................................129
11.5
Chapter 12
Creating Accounts to Manage GV-TAWeb .........................................133
GV-VMWeb for Visitor Management ............................................. 134
12.1
Connecting to GV-ASManager ...........................................................134
12.2
Creating Accounts to Manage GV-VMWeb ........................................136
12.3 Creating Visitor Profile........................................................................138
12.4 Granting Visitor Access ......................................................................139
12.5 Searching GV-VMWeb Database .......................................................141
iii
12.6 Visitor Self Registration ......................................................................141
12.6.1 Setting Up Mail Server in GV-VMWeb ...................................142
12.6.2 Creating a Visitor Account .....................................................144
12.6.3 Creating a Visit Request........................................................145
Chapter 13
License Plate Recognition ............................................................. 147
13.1 Installing GV-DVR LPR ......................................................................149
13.1.1 System Requirements ...........................................................149
13.1.2 Installing LPR Plugin .............................................................150
13.1.3 Inserting LPR Dongle ............................................................150
13.1.4 Accessing Recognition Results on GV-DVR LPR ..................151
13.2 Setting Up GV-DVR LPR....................................................................152
13.2.1 Step 1: Enabling LPR Functions on GV-DVR LPR ................153
13.2.2
Step 2: Adding GV-DVR LPR to GV-ASManager ..................154
13.2.3
Step 3: Configuring a Channel ..............................................156
13.2.4 Exporting LPR Data...............................................................160
13.2.5 Recognition Engine Version ..................................................164
13.3 Setting Up GV-DSP LPR....................................................................165
13.3.1 Step 1: Enabling Connection with GV-ASManager on GV-DSP
LPR
165
13.3.2
Step 2: Adding GV-DSP LPR to GV-ASManager ..................167
13.3.3
Step 3: Configuring a Channel ..............................................169
13.4 Adding Vehicles .................................................................................171
13.5 Monitoring LPR Activities ...................................................................174
13.5.1 LPR Device View ..................................................................174
13.5.2 Monitoring Windows ..............................................................175
13.6 Receiving Notifications for LPR Activities ...........................................176
13.7 Setting Up Vehicle Hotlist ...................................................................177
13.8 LPR Functions in GV-ASWeb.............................................................180
13.8.1 LPR List ................................................................................181
13.8.2 Vehicle List............................................................................182
13.8.3 LPR Log ................................................................................183
13.8.4
Chapter 14
Access Group Setup .............................................................185
GV-Access Mobile Applications.................................................... 186
14.1 Installing GV-Access ..........................................................................186
14.2
Connecting to GV-ASManager ...........................................................187
14.3 Managing Controllers .........................................................................188
14.4 Managing LPR ...................................................................................191
Chapter 15
Database Settings .......................................................................... 193
15.1 Starting the Database Tools ...............................................................193
iv
15.2 Creating a Database ..........................................................................194
15.3 Other Database Settings ....................................................................195
15.4 Mapping Source Database .................................................................196
15.5.1
Converting Data from the Active Directory Database.............198
15.5.2
Converting Data from the OLE Database ..............................199
Chapter 16 Net Module Utility ........................................................................... 204
Chapter 17 Troubleshooting ............................................................................. 205
Appendix 210
A.
Compatible IP Devices...........................................................................210
B.
Event Notifications .................................................................................211
C.
E-Mail and SMS Alert Symbols..............................................................215
D.
Controller Status....................................................................................216
v
Note for Users Upgrading GV-ASManager
You can keep your current database when upgrading GV-ASManager to the latest version.
Follow the steps below to back up the current database and restore it to the GV-ASManager
after upgrading to the latest version.
1. Go to :\Access Control\ASManager\ASRes\ and there should be four files.
2. Back up the four files in the folder.
3. Uninstall the old GV-ASManager. After uninstalling, only two files remain in the ASRes
folder.
4. Install the latest GV-ASManager.
5. Copy and paste the four files you backed up back to :\Access
Control\ASManager\ASRes.
6. Run ASDBManager.exe from the GV-ASManager program folder at :\Access
Control\ASManager.
vi
7. Select ASManager Database Setting.
8. Select Upgrade to latest database version.
9. The GV-ASManager starts upgrading the database. When the upgrade is complete and
the message “Upgrade database successfully” appears, click OK.
Note: After you upgrade GV-ASManager, it is recommended to also upgrade the GV-AS /
GV-EV Controller firmware. To upgrade the controller firmware, use the Update to the
latest firmware version function in the Net Module Utility. See Chapter 16.
vii
Software Compatibility
The GV-System versions compatible with GV-ASManager V4.0 - V4.2.1 are listed below.
GV-ASManager Version
Compatible GV-System Version
GV-ASManager V4.2.1
GV-System V8.5.9.0
GV-ASManager V4.2
GV-System V8.5.8.0
GV-ASManager V4.1
GV-System V8.5.7.0
GV-ASManager V4.0
GV-System V8.5.5.0 / V8.5.6.0
viii
1
Chapter 1
Introduction
Introduction
The integration of GV-ASManager and GV-AS / GV-EV Controller offers full control of the
entrances of your premise. Up to 1000 units of GV-AS / GV-EV Controllers can be monitored
and controlled by one GV-ASManager.
The following diagram is an example of how the GV-ASManager and GV-AS / GV-EV
Controller can be set up.
Figure 1-1
1
1.1 Main Features
GV-ASManager
•
Control up to 1000 GV-AS / GV-EV Controllers
•
Up to 256 time zones and weekly schedules
•
Up to 40,000 cards
•
Up to 1,000 system users
•
Holiday planning for 14 months
•
Multiple cards per user
•
Four (4) access mode options: Card only mode, Card and PIN Code mode, Card or
Common mode, Release mode
•
Enroll cards in batch mode
•
Door alarms: door held open, door forced entry, tamper, access denied
•
Anti-Duress operation
•
Anti-Passback capabilities
•
Door interlock
•
Man trap in double door configuration
•
Import/export of card and user data in Access or Excel file format
•
User-defined matrix of 16-channel multi-views
•
User-defined screen layout and dual monitor display support
•
SMS or E-Mail notification with user-defined content, video snapshot and user photo
•
Video integration with GeoVision IP devices (GV-System, GV-NVR, GV-Video Server,
GV-Compact DVR, GV-IP Camera) and third-party IP cameras
•
Support for connecting to third-party IP devices using ONVIF, PSIA and RTSP protocols
•
Support Microsoft Access, SQL database and Active Directory database
•
Patrol Tour that requires security personnel to check in at the specified locations
•
Vehicle hotlist to help locate stolen vehicles or other vehicles of interest
•
User interface in English, French, Portuguese, Russian, Spanish, Traditional Chinese
GV-ASRemote
•
Monitor unlimited GV-ASManagers over the Internet
•
Remote door monitoring, video playback, door operation
2
1
Introduction
GV-TAWeb
•
Flexible workforce schedule arrangement
•
Payroll calculation
•
Attendance and payroll report search
GV-ASWeb
•
Remotely watch live view from connected devices
•
Remotely add or delete cards, users, controllers, access groups, cameras
•
Web interface for historical log search with corresponding video and snapshot
•
Log export in Excel, Text, HTML or Zip file formats
•
View access data on Google Maps in the order of access time
GV-VMWeb
•
Web interface for creating visitor database and granting access
•
Visitor record search
•
Visitor self registration
GV-LPR
•
Control up to 255 GV-DVR LPR and / or GV-DSP LPR
•
Up to 40,000 vehicles
•
Multiple vehicles per user
•
Import / export of vehicle data in Access or Excel file format
•
GV-ASWeb: Remotely enroll vehicles and set up GV-DVR LPR or GV-DSP LPR
•
GV-ASWeb: Remotely search detected vehicles, see license plate snapshots, watch
recordings from connected GV-DVR LPR or GV-DSP LPR
GV-Access Mobile Applications
•
Access up to 5 GV-ASManagers from iOS and Android mobile devices
•
Watch live view from cameras associated with a door or lane
•
Lock or unlock a door
•
Check door status to see if any alarm events have occurred at a door
•
Open LPR lanes
3
1.2 Concepts
Understanding the following concepts may help you read through the manual.
Weekly Schedule
A weekly schedule is certain days of the week when a user is granted
access to a secure site.
For details, see 4.4 Setting Weekly Schedule.
Access Group
An access group is a group of users with identical location restrictions
during the same time restraints.
For details, see 4.5 Setting Access Group.
Alarm Condition
An alarm condition is a monitored condition through sensing devices,
and an alarm condition may activate alarms. For example, the AS100
Controller has the ability to monitor 3 sensors, such as door status
sensor, smoke detector and tamper detector. The AS100 Controller
also provides 3 output relays for activating and deactivating electric
lock, siren and emergency door release when the alarm condition
occurs.
For settings of alarm conditions see 4.2.2 Step 2: Configuring the
Doors. For configuring inputs and outputs see GV-AS / GV-EV
Controller User’s Manual.
Anti-Duress
If a person is forced to open the door under threat, he or she can enter
his or her PIN plus 1 to activate an alarm and send a signal to the
ASManager to dispatch the police. For example, the PIN is 5555 and
you enter 5556. The door will open normally (access granted) and the
alarm will be activated. The function is enabled by default in the
system.
Anti-Passback
The feature is designed to prevent card sharing and to enforce use of
entry and exit readers. If a card was used at an entry reader, it must
be used at an exit reader before it will be valid at an entry reader
again.
For settings, see 4.2.2 Step 2: Configuring the Doors.
Interlock
The feature is also called “mantrap” or interlocking”. The feature
interlocks the selected door with one or multiple doors connected to
the same controller. For example, if door A is set to interlock with Door
B and C, neither of Door B or C will unlock when Door A is opened.
When either of Door B or C is opened, Door A will not unlock.
For settings, see 4.2.1 Step 1: Configuring a Controller.
4
1
Two-person A/B
rule
Introduction
The door unlock only when two assigned cards are presented together.
Two Person Card A must be presented before Two Person Card B.
For settings, see 4.3.1 Adding a Single Card.
IP device
The video device is connected to the ASManager through the network.
The ASManager enables you to access the live video from not only
GeoVision IP devices (GV-System, GV-NVR, GV-Video Server,
GV-Compact DVR and GV-IP Camera) but also certain third-party IP
cameras. Connections to IP devices through ONVIF, PSIA and RTSP
protocols are also supported.
For details, see Chapter 5 Video Integration.
Data Group
This feature allows the administrator to restrict a user account to only be
able to read, write or execute the controllers, cards, users, access
groups, time zones and weekly schedules assigned under a data group.
For example, the administrator can create a data group for the sales
department and assign sales department-related cards and controllers
under that data group. Employees in the sales department will only have
access to the cards and controllers of their own department.
For details, see 8.1.1 Adding a New User.
Door Group
When a large number of GV-AS / GV-EV Controllers are connected to
the GV-ASManager, the controllers can be organized into different door
groups, allowing you to quickly upload fingerprints to all the controllers in
a door group instead of uploading to each controller one by one.
For details, see Uploading Fingerprints to Controllers Using Door
Groups section in Chapter 3 of GV-GF Fingerprint Reader User’s
Manual.
5
1.3 Optional Devices
Optional devices can expand the capabilities and versatilities of your GV-ASManager.
Consult your sales representative for more information.
GV-GF1911
Fingerprint Reader
Fingerprints can be enrolled through a GV-GF1911 Fingerprint Reader
installed on the computer of the GV-ASManager. The fingerprint data
are distributed through GV-ASManager to the assigned fingerprint
readers installed on GV-AS / GV-EV Controllers for access control.
Fingerprints can be enrolled locally or remotely using a GV-GF1921 /
1922 Fingerprint Reader through TCP/IP connection with
GV-ASManager.
GV-GF1921 / 1922
Fingerprint Reader
GV-PCR310
Enrollment Reader
6
For local fingerprint enrollment, the user needs to register his or her
fingerprints onsite using a reader connected with GV-ASManager. For
remote fingerprint enrollment, empty fingerprints can be created on
the GV-ASManager first, and the user can register his or her
fingerprints later at a GV-GF1921 / 1922 with the assigned card.
The GV-PCR310 is a USB card reader designed to assist with card
enrollment to GV-ASManager. It reads and transfers the identification
data of a detected card to GV-ASManager. The user can conveniently
establish user accounts on GV-ASManager by inserting the cards in
the GV-PCR310 Enrollment Reader.
2
Chapter 2
Installation
Installation
2.1 System Requirements
For GV-ASManager version 4.1 or later, the minimum hardware and software requirements
are:
OS
32-bit
Windows XP / Vista / 7 / 8 / Server 2008
64-bit
Windows Vista / 7 / 8 / Server 2008 / Server 2012
CPU
Core 2 Duo E8400, 3.0 GHz
Memory
2 x 1 GB Dual Channels
Hard Disk
500 GB
VGA
AGP or PCI-Express, 1280 x 1024 , 32-bit color and support DirectX 10
DirectX
End-User Runtimes (November 2008)
Software
.NET Framework 3.5
SQL Server 2005 Express (optional)
Browser
Internet Explorer 7.0 or later
Note: The software programs End-User Runtimes (November 2008) and .NET Framework
3.5 are required to run the GV-ASManager. The software programs can be found in the
supplied software DVD.
7
2.2 Installing the GV-ASManager
Starting from version 4.0, the GV-ASManager software supplied with GV-AS / GV-EV
Controller can connect with up to 4 controllers for free. If you need to manage more than 4
controllers, a USB dongle is required. GV-ASManager can support connection with up to
1000 GV-AS / GV-EV Controllers.
Note: Starting from GV-ASManager 3.0, no USB dongle is needed to connect to IP
cameras.
To install the USB Dongle drivers:
1. Insert the USB Dongle to your computer.
2. Insert Software DVD to your computer and a window will pop up automatically. Select
Install or Remove GeoVision GV-Series Driver and click Install Geovision USB
Devices Driver.
To install the GV-ASManager:
GV-ASManager V2.0 or later must run with DirectX End-User Runtimes (November 2008)
and .NET Framework. Follow these steps to install the programs.
1. Insert Software DVD to your computer and a window will pop up automatically.
2. If you don’t have DirectX 9.0c installed in your computer, select Install DirectX 9.0c.
3. Select Install DirectX End-User Runtimes (November 2008).
4. Select Install Microsoft .NET Framework Version 3.5.
5. Select Install GeoVision Access Control System, click GeoVision Access Control
System and follow on-screen instructions to complete the installation.
8
2
Installation
2.3 Logging in
Before using the GV-ASManager, you need to set the login ID and password, and create a
database.
1. Click Start, point to Programs, select Access Control and click ASManager. When you
start the system for the first time, the system will prompt you for a Supervisor ID and
Password as below.
Figure 2-1
2. Type a name you wish to be the Supervisor in the ID field and type the password. This
dialog box appears.
Figure 2-2
3. Re-type the ID and Password. If you want to skip the login process in the future, select
Auto Login.
9
4. Click OK. The message “Can’t open database. Would you like to set up database?”
appears.
5. Select Yes to create a database. The ID and password you have configured in Step 1 are
required to access the feature. This dialog box appears.
Figure 2-3
6. Select ASManager Database Setting. The ASManager Database Setting dialog box
appears.
7. You can create either a Microsoft Access database or a Microsoft SQL database.
•
To create a Microsoft SQL database, see Chapter 15 Database Settings.
•
To create a Microsoft Access database for first-time users of GV-ASManager, Select
Setup MDB / MSSQL Database for ASManager. The Setup Database Connection
dialog box appears. Select Microsoft Office Access Database, and click OK. The
program starts creating a database. When it is complete, the message “Setup
database connection successfully” will appear.
8. Restart ASManager. You can see the main screen of the GV-ASManager.
Note: By default the Access database is created at C:\Access Control\ASManager\ASRes.
10
3
Chapter 3
The Main Screen of ASManager
The Main Screen of GV-ASManager
After you run the GV-ASManager, the following main screen will appear. Get yourself familiar
with the main screen, as it will help you when you read further in the following sections.
3.1 Main Screen
Figure 3-1
No. Name
1
2
Function
Menu Bar
The Menu Bar includes the options of File (log in / out the
GV-ASManager), Monitoring (display monitor windows of
alarm, access and event), View (display the function
windows), Setup (set up connected devices and schedules),
Personnel (set up the users’ accounts), Language (select
language of user interface), Tools (set up for notification and
log) and Window (arrange the display of different windows).
Toolbar
The Toolbar includes the options of Login, Logout, Devices,
Areas, Door Groups, Time Zones, Weekly Schedules,
Holidays, Access Groups, Cards, Vehicles, Users and About.
11
3
Device View
Displays a list of connected doors and their current status.
You can change the size of icons to 16 x 16, 24 x 24 or 32 x
32 from the drop-down list.
4
Event Monitor
Displays monitored events of doors.
5
Alarm Monitor
Displays alarm events of doors.
6
Access Monitor
Displays access activities of doors.
7
MultiView
Displays live views of connected cameras from multiple IP
devices. For details, see 5.4 The MultiView Window.
8
Information Window
Displays the information of doors, card readers and monitored
events.
9
Playback
Plays back recorded events from a compatible GeoVision IP
device. For details, see 5.5 Retrieving Recorded Video.
10
Live Video
Displays the live view of one connected camera. For details,
see 5.2 Accessing a Live View.
11
Camera List
Displays a list of connected cameras.
Note: After closing the main screen, GV-ASManager will continue to run in Windows Task
Manager.
3.1.1
Toolbar
Figure 3-2
The buttons on the Toolbar of GV-ASManager:
No. Name
Function
1
Login
Logs in the GV-ASManager.
2
Logout
Logs out the GV-ASManager.
12
3
The Main Screen of ASManager
3
Devices
Defines controllers and doors.
4
Cameras
Searches the GV IP devices on the same network. For
details, see Chapter 5 Video Integration.
5
Areas
Configures Global Anti-Passback. For details, see 6.3 Global
Anti-Passback.
Door Groups
Assigns controllers into door groups to be able to quickly
upload fingerprints to multiple controllers. For details, see
Uploading Fingerprints to Controllers Using Door Groups
section in Chapter 3 of GV-GF Fingerprint Reader User’s
Manual.
Time Zones
Defines the minutes and hours of the day when a user is
granted access to a secure site. For details, see 4.4.1 Step 1:
Setting Time Zones.
8
Weekly Schedules
Defines the days of the week when a user is granted access
to a secure site. For details, see 4.4.2 Step 2: Setting Weekly
Schedules.
9
Holidays
Defines the specific dates as holidays. For details, see 4.4.3
Step 3: Setting Holidays.
Access Groups
Sets up different groups to define who can access what door
at what time of a day. For details, see 4.5 Setting Access
Groups.
11
Fingerprint Access
Uploads the enrolled fingerprints to the controllers. For
details, see Chapter 3 Fingerprint Only Mode in the GV-GF
Fingerprint Reader User’s Manual.
12
Cards
Creates and edits a database of card information. For details,
see 4.3 Setting Cards.
13
Vehicles
Creates and edits a database of vehicle information. For
details, see Chapter 13 License Plate Recognition.
14
Users
Creates and edits a database of user information. For details,
see 4.6 Setting Users.
15
About
Displays the version of GV-ASManager.
6
7
10
13
3.2 Device View
The Device View displays the activity and status of the connected doors.
•
To open the Device View window, click View on the menu bar and select Controllers.
Figure 3-3
3.2.1
Controls on the Window
You can control a connected controller or door by right-clicking it in the Controller window.
The following control options are available for both doors and controllers:
Name
Function
Unlock Door, Lock Down,
Force Unlock, Force Lock,
Disable Door Lock Operation
Controls the selected door or all doors associated with the
selected controller.
The options of Force Unlock and Force Lock will let the
door stay open or locked until you select Disable Door Lock
Operation.
The Unlock Door option will let the door open temporarily
until the specified time is expired. See “Lock Reset Time” at
Step 2 in 4.2.2 Step 2: Configuring the Doors.
The Lock Down function locks down the selected door or all
doors associated with the selected controller. This function
overrides the Authentication Schedule and the door(s) can
only be opened by presenting the assigned access card.
Reset Anti-Passback
Clicking this option enables a user to re-access the entry or
exit reader.
See Chapter 6 Anti-Passback.
Settings
14
Accesses the setting page of the selected controller or door.
3
The Main Screen of ASManager
The following control options are only available when right-clicking a Controller:
Name
Function
Reset Anti-Passback
Clicking this option enables a user to re-access the entry or
exit reader.
See Chapter 6 Anti-Passback.
Reconnect
Reconnects with the controller.
Sync Controller
After the controller settings are modified, clicking Sync
Controller can immediately renew the settings.
The following control options are only available when right-clicking a Door:
Name
Function
Stop Alarm, Clear Forced
Clears the alarm conditions.
Open, Clear Duress, Clear
For alarm settings, see Step 5 in 4.2.2 Step 2: Configuring
the Doors.
Tamper, Clear Fire Alarm,
Clear Held Open, Clear
Access Denied
Sync GeoFinger
If fingerprint data failed to upload to the controllers, click
Sync GeoFinger to re-upload the selected fingerprint data.
15
3.3 Monitoring Windows
Three monitoring windows are provided for users to oversee different types of door activities:
Access Monitor, Alarm Monitor and Event Monitor.
•
To open these windows, click Monitoring on the menu bar, and select the desired
windows.
3.3.1
Controls on the Window
The three monitoring windows of Access Monitor, Alarm Monitor and Event Monitor have the
same controls on the window.
We use the Access Monitor window as example to explain the controls.
1
2 3
4
Figure 3-4
No.
Name
1
Filter
2
Auto Select
Sets up criteria to only display the desired activity
information.
Focuses on the latest data display.
3
Lock
Suspends the current data display.
4
Lists / Tiles / Thumbnails
Decides how events are displayed on the window.
16
Function
3
The Main Screen of ASManager
The following options are only accessible on the Access Monitor window. Right-clicking one
message allows you to access its detailed information.
Name
Function
New/Edit Card
Enrolls a new card or edits the card information.
Browse Card Information
Views the card information.
Browse User Information
Views the user information.
Show Image
If the camera monitors when the activity happened,
the related image is available.
3.3.2
Customizing a Monitoring Window
You can customize the messages displayed on a monitoring window by defining filter criteria.
Multiple custom monitoring windows can be added for your specific requirements.
1.
To add one monitoring window, click Monitoring on the menu bar. Then select New
Alarm Monitor, New Access Monitor or New Event Monitor.
2.
Click the Filter button on the monitoring window. This dialog box appears.
Figure 3-5
3.
Select the desired messages and devices for monitoring, and click OK. The monitoring
window will only display the messages based on the defined criteria.
17
4.
Right-click the Monitor tab on the main screen, and select Rename to name the new
monitoring window.
Figure 3-6
Note: The added windows are only for one-time use, and they cannot be saved after the
monitoring window is closed.
3.3.3
Arranging Monitoring Windows
The monitoring windows can be arranged on screen in several ways.
On the menu bar, click Window, and select one of the following options to arrange the
windows:
„
Cascade: Overlaps the open windows and shows their title bars.
„
Tile Horizontally: Arranges the open windows horizontally.
„
Tile Vertically: Arranges the open windows vertically.
„
Arrange Icons: Arranges the minimized windows on the bottom.
You can also open the monitoring windows in separate windows and place the monitoring
windows on different monitors. On the menu bar, click Window and select New Window. On
the menu bar of the new window, click Monitoring to open different monitor windows and
click Window to arrange them.
Figure 3-7
18
4
Chapter 4
Settings
Settings
This section describes the following settings:
•
Setting Controllers
•
Setting Cards
•
Setting Weekly Schedules
•
Setting Access Groups
•
Setting Users
4.1 Setup Flowchart
To get started quickly with GV-ASManager settings, follow the process illustrated below.
Set Controllers
Set Doors
Set Controllers
Add One Card
Run Test
Set Weekly
Schedules
Present the card to the card reader to see if the
message “Access Granted” is displayed.
Set
Holidays
Set Weekly
Schedules
Set
Time Zones
Set Access Groups
Add All Cards
Assign defined Access
Groups to cards
Create cards one by
one or in batch
Add Users
Assign created cards
to users
Create users
19
4.2
Adding Controllers
To add the GV-AS / EV Controller to the GV-ASManager, follow these steps:
•
Step 1 Configuring a Controller
Establish the communication between the controller and GV-ASManager.
•
Step 2 Configuring the Doors or Elevator Floors
Define the doors on a door controller or the elevator floors on an elevator controller.
4.2.1
Step 1: Configuring a Controller
1. On the menu bar, click Setup and select Device. This dialog box appears.
Figure 4-1
2. Click the Add icon on the top left corner. This dialog box appears.
Figure 4-2
20
4
Settings
3. Enter ID and Name of the Controller, select Type of the Controller and click OK. This
dialog box appears.
Figure 4-3
Note: The Controller ID must match the Controller ID set ahead with GV-ASKeypad or on the
Web interface of the controller. Refer to GV-AS / GV-EV Controller User’s Manual.
4. In Connection section, select the communication mode between the GV-AS / GV-EV
Controller and GV-ASManager.
•
If using RS-485 connection, select COM Port that is used for connection.
•
If using Ethernet, select Network and select TCP / IP or LocalDDNS. Type the IP
address, device name (if LocalDDNS is selected), port number, login user, login
password and Crypto key (3DES code) of the controller.
21
Note: The default values of GV-AS / GV-EV Controller are: IP address 192.168.0.100;
username admin; password admin; Crypto key (3DES code) 12345678.
5. To check if the above connection settings are correct, you can click OK at this step and
back to the main screen. The icon
the connection is established.
appearing on the Device View window indicates
Note: For the disconnection messages displayed on the Status column (Figure 4-6), see D.
Controller Status in Appendix.
6. OPTIONAL settings in the General section:
„
GMT: The current time at the host computer.
„
Data Group: Assign the controller to a data group or select No Groups to disable
the data group function. You can then allow or forbid a user to read / write / execute
the functions assigned under the data group. Refer to Adding a New User in Chapter
8 for more details.
„
Release All Doors by Card: When a card is presented, all doors set to Release by
Card mode will open and will remain open until the end of Release by Card mode
set in the Authentication Schedule. For Authentication Schedule, see 4.2.2 Step 2:
Configuring the Doors.
„
Enable Daylight Saving: Enable the Daylight Saving Time function by selecting
your time zone . The system will automatically adjust for daylight saving time.
Note: The Interlock and Release All Doors by Card functions are not available for
GV-EV48.
22
4
4.2.2
Settings
Step 2: Configuring the Doors or Elevator Floors
A. GV-AS Controller: Doors
1. To define the doors on the controller, click the Door / Gate tab. This dialog box appears.
Figure 4-4
2. In the General section, select Enable to define the general settings for the door:
„
Name: Give a name to the door.
„
Common Password: Set a password for the door. When under Card or Common
Mode, the user can gain access by entering this password using a keypad. The
default password is 1234. See Step 6 for details on Card or Common Mode.
„
Urgent Code: When the Urgent Code is entered, the door with the urgent code will
unlock. However, the door will not unlock if it is in Release by Card Mode. The
Urgent Code function is only supported by GV-AS210 / 410 / 810.
23
„
Lock Reset Time: If the door is monitored, type the number of seconds the door can
be held open. After the specified time expired, the door will automatically be locked.
Next to Handicap Card, type the number of seconds the door will be held open
when a Handicap Card is swiped.
„
Held Open Time: If the door is monitored, type the number of seconds the door can
be held open before a Door Held Open alarm is generated. Next to Handicap Card,
type the number of seconds the door can be held open after a Handicap Card is
swiped before a Door Held Open alarm is generated.
„
Lock Card Time: The user will be denied access if he or she tries to re-access the
door more than 1 time within the specified Lock Card Time. For example, if the Lock
Card Time of a cafeteria entrance is set to 7200 seconds, someone who entered the
cafeteria at 9 am will be prevented from re-entering the cafeteria until 11 am.
„
Fire Action: Set the door to be locked or unlocked when a fire alarm condition
occurs.
3. The following settings are OPTIONAL and are only applicable when related settings are
also configured:
„
Reader’s Keypad: When the Card and PIN Code Mode is applied, normally both the
access card and PIN code are required. But if the Entrance or Exit option is not
selected, only the access card is required to unlock the door. For example, if only the
Entrance option is selected, the user will be required to both present the card and
enter the PIN code to unlock the entry door, but only the card will be required to
unlock the exit door. To apply Card and PIN Code mode, see step 4 below.
„
Anti-Passback: To perform the Anti-Passback application, see Chapter 6
Anti-Passback.
„
Auto Check Out: Automatically checks out the Visitor Card when the visitor
presents the card at the exit door. To set a card as Visitor Card, see Adding a Single
Card section later in this chapter.
„
Two Person Rule: Select Entrance to require presenting Two Person A Card and
then Two Person B Card before the entry door is unlocked. Select Exit to require
presenting both cards in the right order before the exit door is unlocked. To set a
card as Two Person A/B Card, see Adding a Single Card section later in this chapter.
„
GeoFinger: Allow GV-ASManager to upload enrolled fingerprints to the specified
fingerprint reader. Refer to Chapter 3 Fingerprint Only Mode in the GV-GF
Fingerprint Reader User’s Manual for details.
24
4
„
Settings
Interlock: Enable Interlock function with the selected doors. Doors that are
interlocked cannot be open at the same time. The door only unlocks when the other
door is close. Using the settings in Figure 4-4 as an example, Gate 1 will not unlock if
either of Gate 4 and 5 is opened, and when Gate 1 is opened, Gate 4 and 5 cannot
be opened.
„
Time Clock: This option must be selected to enable GV-TAWeb. See Chapter 11
GV-TAWeb for Workforce Schedule for more details.
4. The settings in the Alarm Event section are OPTIONAL unless an alarm device is
installed on the GV-AS Controller. Enable the desired alarm conditions that will cause the
alarm to occur: Held Open, Force Open, Tamper, Fire Alarm, Access Denied,
Tailgating and Urgent Code entered.
„
Alarm Continuous Time: Type the duration of the alarm sounds in seconds for
Access Denied alarm.
5. The settings in the Camera Mapping section are OPTIONAL unless a camera is installed
at the secure site. For details see Chapter 5 Video Integration.
6. The Authentication Schedule is an OPTIONAL setting for specifying different access
modes at different periods of time; otherwise the default access mode is Card Mode that
requires users to present the card only to be granted access.
Figure 4-5
To define which kind of access mode should be applied at specific day and time, select
one access mode on the toolbar and drag the mouse over the timelines. Four (4) access
modes are available in the system:
„
Card Mode: This is the default mode. This mode only requires the user to present
his or her card to be granted access.
25
„
Release Mode: Keep the door in an unlock status with the reader.
•
Release by Card: The door will unlock only after a card is presented and will
remain unlocked during the time specified for Release Mode. This option is
designed to prevent unattended doors from opening during the Release Mode.
„
Card and PIN Code Mode: This mode requires the user to present the card and
then enter the card’s PIN code on the keypad. For the following controllers, the user
can gain access by entering the card number and pin code:
Model
GV-AS100
Supported
Command
Firmware
(Example: Card 12345678, Pin 0000)
V1.04 or later
Card Number + Pin Code
Example: 123456780000
GV-AS110
V1.04 or later
*Card Number + Pin Code #
Example: *123456780000#
GV-AS400
V1.04 or later
Pin Code + Card Number
Example: 000012345678
GV-AS210 / 410 / 810 V1.0 or later
Pin Code + Card Number
Example: 000012345678
„
Card or Common Mode: This mode requires the user to present his or her card to
gain access OR enter the door’s password using the keypad to gain access.
26
4
Settings
7. The Exit Button Schedule is an OPTIONAL setting to specify when to allow access to
the exit button. By default, access to the exit button is granted at all times. To set a
and drag the mouse over the time
schedule, click the Delete Access Time button
periods when you want the exit button to be locked. This function is only supported by
GV-AS210 / 410 / 810.
Figure 4-6
8. Click OK several times and return to the main screen. A controller folder tree will be
displayed on the Device View window as example below.
If the icon
appears, it indicates the connection between the controller and
GV-ASManager has been established. If the icon
appears, it indicates the connection
failed. Make sure the above connection setup is correctly configured.
Figure 4-7
27
B. GV-EV Controller: Floors
1. To define the elevator floors on GV-EV48, click the Floors tab. This dialog box appears.
Figure 4-8
2. To enable elevator floors, select the floors on the left. For example, if your elevator only
has 40 floors, you can clear the selection for floors 41 to 48.
3. In the General section, define the general settings for the elevator:
„
28
Name: Name the elevator.
4
„
Settings
Common Password: Set a password for the elevator. When under Card or
Common Mode, the user can gain access by entering this password using a keypad.
The default password is 1234.
„
Relay Reset Time: If the elevator access is restricted, type the number of seconds
the buttons will remain accessible after card is presented. After the specified time
expired, the elevator buttons will automatically be locked. Next to Handicap Card,
type the number of seconds the elevator button will remain accessible when a
Handicap Card is swiped.
4. The following settings are OPTIONAL and are only applicable when related settings are
also configured:
„
Two Person Rule: Select to require presenting Two Person A Card and then Two
Person B Card before the elevator floor is unlocked. If Two Person A Card and Two
Person B Card have access to different floors, access will only be granted if both
cards have access to that particular floor. To set a card as Two Person A/B Card,
see Adding a Single Card section later in this chapter.
„
Time Clock: This option must be selected to enable GV-TAWeb. See Chapter 11
GV-TAWeb for Workforce Schedule for more details.
„
GeoFinger: Allow GV-ASManager to upload enrolled fingerprints to the specified
fingerprint reader. Refer to Chapter 3 Fingerprint Only Mode in the GV-GF
Fingerprint Reader User’s Manual for details.
5. The Authentication Schedule is an OPTIONAL setting for specifying different access
modes at different periods of time; otherwise the default access mode is Card Mode that
requires users to present the card only to be granted access.
Figure 4-9
29
To define which kind of access mode should be applied at specific day and time, select
one access mode on the toolbar and drag the mouse over the timelines. Four (4) access
modes are available in the system:
„
Card Mode: This is the default mode. This mode only requires the user to present
his or her card to be granted access.
„
Release Mode: Keep the door in an unlock status with the reader.
•
Release by Card: The floor will unlock only after a card is presented and will
remain unlocked during the time specified for Release Mode. This option is
designed to prevent unattended floors from opening during the Release Mode
time.
„
Card and PIN Code Mode: This mode requires the user to present his or her card
and then enter the card’s PIN code on the keypad. The user can also be granted
access by entering Pin Code + Card Number. For example, if the card number is
12345678 and the Pin is 0000, the command will be 000012345678.
„
Card or Common Mode: This mode requires the user to present his or her card to
gain access OR enter the door’s password using the keypad to gain access.
6. The settings in the Camera Mapping section are OPTIONAL unless a camera is installed
at the secure site. For details see Chapter 5 Video Integration.
7. Click OK several times and return to the main screen. A controller folder tree will be
displayed on the Device View window.
appears, it indicates the connection between the controller and
If the icon
GV-ASManager has been established.
If the icon
appears, it indicates the connection failed. Make sure the above
connection setup is correctly configured.
30
4
Settings
4.3 Setting Cards
Once you have configured the controller, you may start enrolling cards. All new cards must be
enrolled into the GV-ASManager before access is allowed. Up to 40,000 cards can be stored
using a GV-AS / GV-EV Controller. If a card that was not enrolled is presented to the reader,
the message Access Denied: Invalid Card will be displayed.
Depending on how many cards you need to program, you can simply add them one at a time
or use the batch function to add a group of cards.
4.3.1
Adding a Single Card
1. To add one card, use one of these ways:
•
Present the card to the reader. The message Access Denied: Invalid Card is
displayed. Right-click the message and select New / Edit Card. The New a Card
dialog box appears with card number and code type entered (Figure 4-11). Then
follow Step 3 to complete other settings.
•
On the menu bar, click Personnel and select Cards. This window appears.
Figure 4-10
Note: You can also enroll card by installing the optional device GV-PCR310 Enrollment
Reader to the PC running GV-ASManager. Refer to GV-PCR310 Enrollment Reader’s
Installation Guide for more details.
31
2. Click the New button on the toolbar. This dialog box appears.
Figure 4-11
3. The settings are available for the card:
„
Card Number: Enter the card number.
„
Code Type: Select the code format of the card.
„
Card Type: Select one of the following card types.
• Normal: The card opens the door when it is under Card Mode, the default mode.
• Patrol: The card is assigned to the person in charge of patrolling a location, e.g. a
guard. When the patrol card is presented to the reader, the access will be
recorded but the door will NOT unlock. The feature may be set together with
Privilege below. The patrol card user may have the privilege to stop alarm
sounds and clear alarm events during patrolling.
32
4
Settings
• Two-person A Card: Two-person A/B rule. The card is defined as Card A. Card
B must be presented after Card A to unlock the two-person-rule enabled door.
• Two-person B Card: Two-person A/B rule. The card is defined as Card B. Card
A must be presented before Card B to unlock the two-person-rule enabled door.
• Visitor: This card is assigned to a visitor and the visitor’s access can be
managed using GV-VMWeb.
• Security: The security card can enable the Security Mode where no cards can be
granted access. Only the security card can disable the Security Mode.
• Handicap: When the handicap card is used, the door will remain unlocked for the
time specified in Lock Reset Time and Held Open Time for handicap card. To see
how to set prolonged Lock Reset Time and Held Open Time for handicap card
users, refer to 4.2.2 Step 2: Configuring the Doors or Elevator Floors.
„
Activation/Deactivate Date: Specify when the card is active or inactive.
„
PIN Code: Enter a four-digit personal code for the card. The default setting is 1234.
„
Privilege: Assign one of these privileges to the user:
• Stop Alarm: The user can stop alarm sounds by presenting the card.
• Clear Event: The user can clear alarm events by presenting the card. All alarms
in the Device View window are erased. A record of these alarms is still kept in the
Alarm Monitor.
„
Disable Lock Card: When the option is selected, the card will be exempt from the
Lock Card Time setting. For details on Lock Card Time, refer to Step 2: Configuring
the Doors or Elevator Floors in Chapter 4.
„
Access Group: Access Groups control which personnel can access which door and
at what time. For details, see 4.5 Setting Access Groups.
For first-time user of the GV-ASManager, the access group is not yet established.
Select User Define for test run.
„
Controller: The Controller column displays the associated doors. The selection for
each door will be automatically brought up when one access group was entered.
For first-time user of the GV-ASManager, select 24-hour access for each door for
test run.
„
Data Group: Assign the card to a data group or select No Groups to disable the
data group function. You can then allow or forbid a user to read/write/execute the
functions listed under the data group. Refer to Adding a New User in Chapter 8 for
more details.
33
4. Present the enrolled card to the reader. Once the card has been accepted, the message
Access Granted will be displayed.
Note: GV-AS200 only supports the first 10,000 cards. All other controllers can support up to
40,000 cards.
34
4
4.3.2
Settings
Adding a Group of Cards
Before you use the Batch function to enroll new cards, please note that the group of cards
must be numbered sequentially.
1. On the menu bar, click Personnel and select Cards. The Card List dialog box appears.
2. Click the Batch New button on the toolbar. This dialog box appears.
Figure 4-12
3. The settings in the dialog box are the same as those of adding a single card. See Step 3
in 4.3.1 Adding a Single Card.
Note: Cards that were enrolled using the Batch function will have the same PIN. If you want
to change the PINs of certain cards, you have to enter the PIN using the Edit function on the
Card List dialog box.
4.3.3
Importing/Exporting Card Data
You can import and export card data in mdb or xls format.
To export card data:
1. On the Card List window (Figure 4-8), select desired cards using Ctrl + left click.
2. Click the Export button and select Export to Access or Export to Excel.
3. Assign the file path, and optionally enter password to export card data.
35
Note: The Excel file format does not support the password protection.
To import card data:
1. On the Card List window (Figure 4-10), click the Import button and select one of these
options: Import from Access or Import form Excel.
2. Assign the file path and type the Password if necessary. Click OK. This dialog box
appears.
Figure 4-13
3. Select the Source Table you want to import.
4. Click the Auto mapping button to automatically map the Source fields to the current card
data fields.
5. You can also manually map the fields by clicking the columns under Source Fields.
6. Click Import to import card data.
36
4
Settings
4.4 Setting Weekly Schedules
This section will help you define the daily and holiday access times. Up to 254 weekly
schedules may be defined with two default weekly schedules for “deny access” and “full
access”.
Before creating weekly schedules, it is helpful to map out all possible usages of weekly
schedules for the site. For example: consider the variety of access hours for employees,
consider requirements for janitorial personal who may need night access, consider
requirements for service or repair personnel who may need all hours access, consider
requirements for supervisory staff who may need extended hours access and etc.
•
Step 1 Setting Time Zones
Define the minutes and hours of the day when a user is granted access to a secure
site. The minimum time duration is 5 minutes.
•
Step 2 Setting Weekly Schedules
Define the days of the week when a user is granted access to a secure site.
•
Step 3 Setting Holidays
Define specific dates as holidays.
4.4.1
Step 1: Setting Time Zones
This section provides examples of setting the following time zones:
•
Day shift – 09:00 to 19:00 hours
•
Night shift – 19:00 to 9:00 hours (cross midnight)
•
Supervisor – 07:00 to 24:00 hours
37
1. On the menu bar, click Setup and select Time Zones. This dialog box appears.
Figure 4-14
2. Click the Add button
. This dialog box appears.
Figure 4-15
3. The ID is the number of the time zone. The system will automatically create the ID based
on how many time zones have been added. Give a Name to the time zone you are going
to define. Click OK.
For example, name the Time Zone 1 as day shift.
4. Click the Add Access Time button
period of access time.
. Then drag the mouse on the timeline to define a
For example, the time of day shift is from 09:00 to 19:00.
5. To create the second time zone, click the Add button and name it as night shift. Then
click the Add Access Time button. Drag the mouse on the timeline to set the time from
19:00 to 24:00 and from 00:00 to 09:00.
6. To create the third time zone, click the Add button and name it as Supervisor. Then click
the Add Access Time button. Drag the mouse on the timeline to set the time from 07:00
to 24:00.
7. You can use the Data Group drop-down list to assign the time zone to a data group or
select No Groups to disable the data group function. You can then allow or forbid a user
to read/write/execute the functions assigned under the data group. Refer to Adding a New
User in Chapter 8 for more details.
8. Click OK. The three time zones have been defined.
38
4
4.4.2
Settings
Step 2: Setting Weekly Schedules
This section provides examples of setting the following weekly schedules:
•
Schedule-Day shift – Monday through Friday, 09:00 to 19:00 hours
•
Schedule-Night shift – Monday through Friday, 19:00 to 9:00 hours
•
Schedule-Supervisor – Monday through Sunday and Holidays, 07:00 to 24:00 hours
1. On the menu bar, click Setup and select Weekly Schedules. This dialog box appears.
Figure 4-16
2. Click the Add button. This dialog box appears.
Figure 4-17
3. The ID is the number of the weekly schedule. The system will automatically create the ID
based on how many time schedules have been added. Give a Name to the weekly
schedule you are going to define. Click OK.
For example, name the Weekly Schedule 1 as Schedule-Day shift.
39
4. From the drop-down lists of Monday to Friday, select the Day shift time zone we have
created. No access is allowed on Saturday, Sunday and Holiday.
Figure 4-18
5. To create the second time schedule, click the Add button and name it as Schedule-Night
shift. From the drop-down list of Monday to Friday, select the Night shift time zone we
have created. No access is allowed on Saturday, Sunday and Holiday.
6. To create the third time schedule, click the Add button and name it as
Schedule-Supervisor. From the drop-down lists of Monday to Hol, select the
Supervisor time zone we have created.
Figure 4-19
7. You can select a time schedule and use the Data Group drop-down list to assign the time
schedule to a data group or select No Groups to disable the data group function. You can
then allow or forbid a user to read/write/execute the functions assigned under the data
group. Refer to Adding a New User in Chapter 8 for more details.
8. Click OK. The three weekly schedules have been defined.
40
4
4.4.3
Settings
Step 3: Setting Holidays
To designate specific dates as holidays on the system:
1. On the menu bar, click Setup and select Holidays. This dialog box appears.
Figure 4-20
2. Click the Holiday icon and click the dates you want to set as holidays. For example,
•
Dec 24, 2007 – Christmas Eve
•
Dec 25, 2007 – Christmas Day
•
Dec 31, 2007 – New Year’s Eve
•
Jan 01, 2008 – New Year’s Day
3. To delete the holiday, click the Non Holiday icon and click the date you want to delete.
Note: Holiday dates can cross over to the following year, and certain holiday dates change
from year-to-year. Administrators should review and update the holiday setting prior to the
beginning of a new year to ensure proper holiday coverage.
41
4.5 Setting Access Groups
An access group defines which doors or lanes can be accessed at what times. You can
create multiple access groups to suit the schedules of different groups of employees. Instead
of setting the access rights of each card one by one, you can quickly assign a card to an
access group and the access rights of that access group will be applied to the card.
This section describes how to create an access group and assign a card to the access group.
In the example below, an access group was created to give office staff access to all 4 doors
of Controller 1 during daytime shift.
1. On the menu bar, click Setup and select Access Groups. This dialog box appears.
Figure 4-21
, and give a Name to the new access group. For example, name
2. Click the New button
the access group Office Staff.
42
4
Settings
3. To define door access for the access group, click the drop-down list next to each door and
select one of pre-defined Weekly Schedules. For example, click the blue text next to Door
1, and then select Schedule-Day Shift.
4. You can use the Data Group drop-down list to assign the access group to a data group or
select No Groups to disable the data group function. You can then allow or forbid a user
to read/write/execute the functions assigned under the data group. Refer to Adding a New
User in Chapter 8 for more details.
5. Click OK. The access group for office staff has been created.
6. To assign the criteria of the access group to a single card, click Personnel on the menu
bar and select Cards. The Card List dialog box appears.
7. Double-click one listed card. This dialog box appears.
Figure 4-22
8. From the Access Group drop-down list, select one pre-defined access group, e.g. Office
Staff. The assigned Weekly Schedule will be displayed on the associated door’s field.
43
4.6 Setting Users
This section describes how to create a database of user information and assign cards to
users.
4.6.1
Adding a User
1. On the menu bar, click Personnel and select Users. The User List window appears.
2. Click the New button on the toolbar. This dialog box appears.
Figure 4-23
3. Type a name under Display, which is a required field. Other user information such as
Employee ID, Photo, Home information and Company information are optional entries.
4. You can use the Data Group drop-down list to assign the user to a data group or select
No Groups to disable the data group function. You can then allow or forbid a user to
read/write/execute the functions assigned under the data group. Refer to Adding a New
User in Chapter 8 for more details.
You can enroll fingerprints in the Fingerprint tab using GV-GF1911 / 1921 / 1922. For details,
refer to Chapter 3 Fingerprint Only Mode in the GV-GF Fingerprint Reader User’s Manual.
44
4
4.6.2
Settings
Assigning a Card to a User
There are two methods to assign a card to a user.
Note: At this step we assume that you have followed the instructions in 4.3 Setting Cards to
complete your card enrollment.
1. On the User Setup dialog box (Figure 4-23), click Add and double-click one listed card to
assign the card to the user.
2. On the Edit Card dialog box (Figure 4-22), click the Assign User icon
and
double-click one listed user to assign the user to that card.
4.6.3
Sending SMS Alerts
If you want to send SMS alerts whenever the card(s) assigned to the user is presented to the
reader, select Send SMS in the User Setup dialog box.
Before sending the SMS, see 8.2.1 Setting SMS Server to configure the SMS server. For how
to set up SMS alerts, refer to the same settings “Send SMS Alert” at Step 3 in 8.2.3 Setting
Notification.
4.6.4
Customizing a Data Field
You can customize data fields for users. Up to ten data fields can be created for user data
entry.
When a custom data field is created, the field label will be displayed in the User Define tab on
the User Setup dialog box. The actual personal data for each user is entered in the User
Define tab.
To customize a data field:
1. On the menu bar, click Personnel and select User. The User List window appears.
2. Click the User Define Fields Setting button on the toolbar. The User Define Fields
Setting dialog box appears.
45
3. Select one User Define field, and type the text to be displayed as the field label. In this
example, a Parking Space Number field was created.
Figure 4-24
To enter personal data:
1. On the menu bar, click Personnel and select User. The User List window appears.
2. Double-click one listed user to whom personal data should be entered. The User Setup
dialog box appears.
3. Click the User Define tab. The custom data field you have created now is displayed.
4. Click in the custom data field and enter the appropriate information. In this example, a
number is entered in the created Parking Space Number field:
Figure 4-25
46
4
4.6.5
Settings
Importing/Exporting User Data
From the User List window, you can import and export user data in mdb or xls format. For this
function, please refer to 4.3.3 Importing / Exporting Card Data.
47
Chapter 5
Video Integration
GeoVision IP devices and certain third-party IP cameras can be connected to the
GV-ASManager through the network. Live video can then be accessed for monitoring and
surveillance purposes.
The GV-ASManager provides the following video features:
•
Live view
•
Video playback
•
Monitor up to 16 cameras at one time
Note:
1. GeoVision IP devices include GV-System, GV-NVR, GV-Video Server, GV-Compact
DVR and GV-IP Camera. For compatible third-party IP cameras, see Appendix A.
2. To connect third-party IP cameras to GV-ASManager V2.3 and earlier versions, a NVR
Dongle is required.
3. The GV-ASManager only supports GV-System of version 8.120 or later.
4. GV-Fisheye IP Camera is currently not supported on GV-ASManager.
Hint: In the following sections the term “DVR” refers to GV-System and GV-NVR, the term
“Video Server” refers to GV-Video Server, and the term “Compact DVR” refers to
GV-Compact DVR.
5.1 Mapping Cameras
If you want to map a camera from the DVR to a door, the DVR must be enabled for video
access ahead:
•
Enable Control Center Server (CCS)
To map cameras to a door:
1. On the menu bar, click Setup and select Device. The Controller List dialog box appears.
2. Double-click one listed controller. The Controller Setup dialog box appears.
48
5
Video Integration
3. Click a Gate tab.
4. In the Camera Mapping section, click the first Arrow button.
Figure 5-1
5. To connect one IP device to the GV-ASManager, use one of these ways:
Figure 5-2
•
Click Add, select the type of the IP device, and type its IP address and login
information.
•
Click Search to detect all GV-IP Devices or GV-Systems on the same LAN. After the
found device is added, click the Modify button to enter its login ID and password.
6. Expand the Host folder listed in the DVR List dialog box (Figure 5-2), select one camera
and click OK. The mapped Host Name and Camera are displayed on the Controller
Setup dialog box.
7. To map the second camera to the door, click the second Arrow button, and follow Steps
5 and 6 to add another camera.
8. Click OK and return to the main screen.
9. Click the specific door on the Device View window. The associated live view is displayed
on the Live Video window.
49
Tip:
1.
You can modify the host or camera name in the DVR List dialog box (Figure 5-2) by
clicking the listed name directly.
2.
GV-ASManager is compatible with third-party IP devices using RTSP, ONVIF and PSIA
protocols. To connect through RTSP, ONVIF and PSIA protocols, click the Add button,
select Add IPCam Mapping and select Protocol in the Brand drop-down list to choose
the type of protocol. For the RTSP commands, refer to the third-party IP camera’s user
manual.
5.2
Accessing a Live View
After mapping cameras to doors, use one of the following methods to access a live view on
the Live Video window:
•
On the Device View window, click the desired door. Its associated live view will appear.
•
On the Camera List window, click the desired camera. Its associated live view will
appear.
•
On the Alarm Monitor and Access Monitor windows, click the desired event. Its
associated live view will appear.
To access live views from multiple IP devices, see 5.4 The MultiView Window below.
50
5
5.2.1
Video Integration
Live Video Window
1
2 3
4
5
6
Figure 5-3
The controls on the Live Video window:
No. Name
Function
Switches between two cameras when you have mapped two
1
Camera List
2
Best Fit
Rescales the image to fit any resized window.
3
Actual Size
Displays the image in its original size.
4
Zoom
Zooms in or out the image.
cameras to the selected door.
Displays a thumbnail view (No. 6). When the image size is
5
Thumbnail
larger than the Live Video window, drag the box in the
thumbnail view to have a close look at the image.
6
Thumbnail View
See the description in No. 5.
51
5.3
Accessing a Video Image
You can access the video image captured after the access and alarm triggered event.
•
On the Access Monitor or Alarm Monitor window, double-click the desired event to
display the image. Or, right-click the desired event and select Show Image to display the
image. Notice if there is no image retrievable, the option will be grayed out.
5.4
The MultiView Window
The MultiView window provides a quick view of up to sixteen preset cameras on one screen.
These cameras can be a mix of cameras from several IP devices.
To open and use MultiView:
1. On the menu bar, click View and select MultiView. The MultiView window appears,
similar to Figure 5-4.
2. Drag the desired camera from the Camera List window, and drop it to the required frame
on MultiView.
The video generated by the camera appears in this frame. If a different camera view already
exists in this frame, the new video takes its place.
Figure 5-4
52
5
Video Integration
The controls on the MultiView window:
No. Name
Function
The frame displays live video from the assigned camera. The
1
Frame
camera number and name, controller ID and name will be
displayed in the upper left corner.
Click this option to have a dynamic 3D live view. In the 3D live
view:
•
2
Double-click one camera view to switch between 3D mode
and thumbnails. Then right-click the 3D image to have
3D
different 3D effects.
•
Double-click one camera view in thumbnails to change
different divisions (4, 9 and 16 divisions).
Select the desired camera. The selected camera will be
3
Camera List
4
Previous / Next Page
5
Matrix View
6
Add Matrix
Add a Matrix View.
7
Delete Matrix
Delete a Matrix View.
displayed with mouse focus.
Go to the previous or next page of camera views.
Select an existing Matrix View (a group of views) from the
drop-down list. For details, see 5.4.1 Adding a Matrix View.
Select the image resolution. Double-click one camera view to
8
Resolution
rescale the image to fit the MultiView window or restore to its set
resolution.
Note: It is possible to drag the MultiView window out of the main screen and even drag the
window to place at the second computer monitor.
53
5.4.1
Adding a Matrix View
A Matrix View, or a group of views, is a programmed arrangement of frames in the MultiView
window that can present up to sixteen different camera views. Multiple Matrix Views can be
added as required.
1. In the Matrix View drop-down list (No. 5, Figure 5-4), enter a name for the Matrix View.
2. Click the Add Matrix button. The Matrix View name is created.
3. Drag the desired camera from the Camera List window to an available frame in the
window. The video associated with the camera is displayed in the frame.
4. You can repeat Steps 1-3 to add more than one Matrix View. And use the drop-down list
to change to a different Matrix View.
54
5
Video Integration
5.5 Retrieving Recorded Video
Recorded video can be reviewed by retrieving the video from the DVR (GV-System /
GV-NVR) and playing it back. Before you can review video recorded on the DVR, the
following function must be enabled to allow remote access:
•
DVR: Enable Remote ViewLog Service on Control Center Server
To play back video:
•
On the Access Monitor or Alarm Monitor window, click the desired event. If recorded
video exits, the Playback window will be enabled. Click the Play button to play the video
clip.
Figure 5-5
Figure 5-6
55
Right-click the window to have the following features:
Play Mode
Includes these options:
• Frame by Frame: Plays back video frame by frame.
• Real Time: Plays back video on real time. This mode saves waiting
time for rendering, but drop frames to give the appearance of real-time
playback.
• Auto Play Next 5 Minutes: Plays back video up to 5 minutes.
• Audio: Turns on or off the video sound.
Render
Includes these options:
• Deinterlace: Converts the interlaced video into non-interlaced video.
• Scaling: Smoothens mosaic squares when enlarging a playback
video.
• Deblocking: Removes the block-like artifacts from low-quality and
highly compressed video.
• Defog: Enhances image visibility.
• Stabilizer: Reduces camera shake.
• Text overlay’s camera name and time: Overlays camera name and
time onto the video.
• Text overlay’s POS/GV-Wiegand: Overlays POS or GV-Wiegand
Capture data onto the video.
• Full Screen: Switches to the full screen view.
Tools
•
Snapshot: Saves a video image.
•
Save as AVI: Saves a video as avi format.
•
Download: Downloads the video clip from a GeoVision IP device to
the local computer.
56
6
Chapter 6
Anti-Passback
Anti-Passback
The Anti-Passback is used to ensure one-card and one-way access into and then out of a
controlled area. This function prevents users from passing their cards back to a second
person to gain entry into the same controlled area. Depending on the number of controllers
and communication link, there are three types of Anti-Passback operations: Anti-Passback,
Local Anti-Passback and Global Anti-Passback.
Anti-Passback is performed only on one controller, while Local Anti-Passback and Global
Anti-Passback can be performed on multiple controllers. Anti-Passback is performed through
either RS-485 or TCP/IP connection, while Local Anti-Passback and Global Anti-Passback
are performed only through TCP/IP connection. The following table lists the supported
operations among GV-AS / GV-EV Controllers.
Model
Anti-Passback
Local Anti-Passback
Global Anti-Passback
GV-AS100
Yes
Yes (GV-ASBox or
Yes (GV-ASBox or
GV-ASNet required)
GV-ASNet required)
Yes (GV-ASBox or
Yes (GV-ASBox or
GV-ASNet required)
GV-ASNet required)
Yes (GV-ASBox or
Yes (GV-ASBox or
GV-ASNet required)
GV-ASNet required)
GV-AS110
GV-AS120
Yes
Yes
GV-AS210
Yes
Yes
Yes
GV-AS410
Yes
Yes
Yes
GV-AS810
Yes
Yes
Yes
57
6.1
Anti-Passback
Anti-Passback is used on one controller only. For this application, select Local
Anti-Passback at the Gate tab of the Controller Setup dialog box (Figure 4-3).
Figure 6-1
To reset Anti-Passback on GV-ASManager or GV-ASRemote, right-click the Host or
Controller icon on the Device View window (Figure 3-3) and select Reset Anti-Passback.
58
6
Anti-Passback
6.2 Local Anti-Passback
Local Anti-Passback is used on multiple controllers which are associated with network
connections. Before you start, the following conditions must be true:
•
The communication mode between GV-ASManager and the controller is Ethernet.
•
LAN environment is applied.
Here we use three GV-AS400 Controllers as example to explain how to combine three
controllers together to operate the Anti-Passback (APB) function. Since Anti-Passback is
performed in a network connection, every controller has a unique IP address. When three
controllers are connected for Anti-Passback, an APB IP address is then applied for
interaction.
For example, Controller No. 1, No. 2 and No. 3 are combined in sequence, as illustrated
below. APB IP is the IP address of the associated controller.
IP of Controller No. 1 is 192.168.0.11; APB IP of Controller No. 1 is IP of Controller No. 2.
IP of Controller No. 2 is 192.168.0.12; APB IP of Controller No. 2 is IP of Controller No. 3.
IP of Controller No. 3 is 192.168.0.13; APB IP of Controller No. 3 is IP of Controller No. 1.
Controller No. 1
Controller No. 2
Controller No. 3
IP:192.168.0.11
IP:192.168.0.12
IP:192.168.0.13
APB IP:192.168.0.12
APB IP:192.168.0.13
APB IP:192.168.0.11
59
To configure Anti-Passback for the three GV-AS400 Controllers:
1. Access the AS400 Setting page of the Controller No. 1 Web interface. In the
Anti-Passback section, select Enable and enter Info IP that is the IP address of
Controller No. 2, e.g. 192.168.0.12.
Figure 6-2
2. Access the AS400 Setting page of the Controller No. 2 Web interface. In the
Anti-Passback section, select Enable and enter Info IP that is the IP address of
Controller No. 3, e.g. 192.168.0.13.
3. Access the AS400 Setting page of the Controller No. 3 Web interface. In the
Anti-Passback section, select Enable and enter Info IP that is the IP address of
Controller No. 1, e.g. 192.168.0.11.
4. On the ASManager, select Local Anti-Passback (Figure 6-1) to start the function.
To reset Anti-Passback on GV-ASManager or GV-ASRemote, right-click the Host or
Controller icon on the Device View window (Figure 3-3) and select Reset Anti-Passback.
60
6
Anti-Passback
6.3 Global Anti-Passback
Global Anti-Passback can not only prevent the use of a card to gain successive entries, but
track the user around the site.
The diagram below shows a typical site controlled by access control. The following sections
will guide you through the steps you would need to go through to configure this site for Global
Anti-Passback.
Reader A
(Entry)
RECEPTION
Gate A
OUTSIDE
Reader C
(Entry)
Reader G
(Entry)
Gate B
Reader D
(Exit)
Reader B
(Exit)
MEETING
ROOM
Gate D
SALES
Reader E
(Exit)
FACTORY
Reader H
(Exit)
Gate C
Reader F
(Entry)
Figure 6-3
6.3.1
Step 1: Enabling Global Anti-Passback
Select Global Anti-Passback at each Gate tab of the Controller Setup dialog box (Figure
4-3).
61
6.3.2
Step 2: Configuring Areas
This step is to define the Entry and Exit areas for each door/gate and name the areas
properly.
•
On the menu bar, click Setup and select Areas. This dialog box appears.
Figure 6-4
Enter to is the area where you enter by accessing the Entry reader. Exit to is the area where
you exit to by accessing the Exit reader. In this case, we set up like this:
Gate A: Enter to Reception; Exit to Outside
Gate B: Enter to Sales; Exit to Reception
Gate C: Enter to Meeting Room; Exit to Sales
Gate D: Enter to Factory; Exit to Sales
6.3.3
Step 3: Configuring Readers
This step is to define the Entry and Exit readers for each door/gate. The reader definition tells
the GV-ASManager which reader controls the access across the area boundaries.
When users access unauthorized readers, the message Access Denied: APB (Wrong Area)
will be displayed and the door will remain locked. When users access the same reader
successively, the message Access Denied: APB (Double Entry) will be displayed and the
door will remain locked.
62
6
Anti-Passback
To define readers, you can use GV-ASKeypad or the Web interface of the GV-AS / GV-EV
Controller. Here we use the GV-AS400 Web interface as example to define Wiegand readers.
For this case, Wiegand reader A (Entry) goes from Outside to Reception, Wiegand reader B
(Exit) goes from Reception to Outside and etc.
Figure 6-5
6.3.4
Step 4: Configuring Door Contacts
This step is to define the door contact sensor for each door/gate. When the door contact
sensor is triggered and the door is unlocked, the GV-ASManager can tell the location of the
user based on your area definition at Step 2.
To define door contact sensors, you need to use the Web interface of GV-AS / GV-EV
Controller. In this example of GV-AS400 Web interface, Input 01 is used as Door Contact of
Door A, Input 02 is used as Door Contact of Door B and etc.
Figure 6-6
63
6.3.5
Step 5: Locating Users
To locate a user, select Monitoring on the menu bar and select New Locate Person.
When the Exit or Entry reader is triggered, the GV-ASManager can tell if users follow
Anti-Passback rules and then grand or deny access. When the door contact sensor is
triggered, the GV-ASManager can tell the location of the user.
Figure 6-7
To reset Anti-Passback on GV-ASManager or GV-ASRemote, right-click the Host or
Controller icon on the Device View window (Figure 3-3) and select Reset Anti-Passback.
64
7
Chapter 7
Patrol Tour
Patrol Tour
Patrol Tour can be created to require security staff to check in at the specified locations
during a certain time period.
7.1 Creating Patrol Tour
Create weekly Patrol Tours by specifying the doors where the security staff needs to check in
during the specified time period. If the security staff does not present their cards at the
specified door on time, an alert notification can be sent using e-mail or SMS message.
1. On the menu bar, click Setup and select Patrol Tours. This dialog box appears.
Add Patrol Tour
Add Patrol Point
Figure 7-1
2. To create a new Patrol Tour, click the Add Patrol Tour button
on the left.
65
3. Select a day in the timeline and click the Add Patrol Point button
This dialog box appears.
above the timeline.
Figure 7-2
4. Select the location and check-in time of the Patrol Point:
„
Controller: Select the controller of the door that the security staff needs to patrol.
„
Door: Select the door that the security staff needs to patrol.
„
Time: Select the time when the security staff should check in at the selected door by
presenting the card.
„
Buffer Period: Specify the Buffer Period in minutes, which will be added before and
after the check-in time specified above. Security staff checking in during the buffer
period will be considered on time. Using Figure 6-7 as an example, the security staff
needs to check in between 5:30am and 6:30am to be considered on time.
„
Extended Buffer Period: The Extended Buffer Period will be added before and after
the Buffer Period specified above. Security staff who checks in during the Extended
Buffer Time is considered late or early, and alert notification can be set off if enabled.
Using Figure 6-7 as an example, check-ins between 4:50am - 5:30am will be marked
as Early, while check-ins between 6:30am – 7:10am are considered late.
„
Patrol Message: Click the … button to type an alert message that can be sent using
e-mail or SMS when the security staff is on time, early, late or absent.
Note: Security staff checking in outside the Extended Buffer Period will be marked as absent.
5. Click OK.
66
7
Patrol Tour
6. To add more Patrol Points, select a day and click the Add Patrol Point button again to
repeat the steps. You can also drag a Patrol Point to another day of week to create a
copy.
Below is an example of a completed Patrol Tour, where the dark green zone is when the
security staff needs to check in and the light green zone is the extended buffer period.
Figure 7-3
67
7.2
Activating the Patrol Tour
1. After you have created the Patrol Tour, double-click the Patrol Tour. This dialog box
appears.
Figure 7-4
2. Click the Add button
and select a card. You can add multiple cards if needed and
the security staff will be required to present one of the cards listed here.
Note: When the security staff presents the card, the controller may grant or deny door access
according to the setting of the card. For example, if the security staff is using a Patrol Card,
the door will remained locked and the security staff will check in without opening the door.
Refer to 4.3 Setting Cards to see how to set the cards.
68
7
Patrol Tour
3. Double-click a card and select to notify by E-Mail and / or Short Message Service.
Figure 7-5
„
E-Mail: Type the e-mail addresses that will receive the alert notifications.
„
Short Message Service: Type up to 3 mobile numbers and their country codes.
4. To set up alert notifications, select the notification conditions to send alert.
Figure 7-6
5. Click Apply.
6. Click Active to activate the Patrol Tour and click OK.
Note:
1.
Once the Patrol Tour is activated, the Patrol Points cannot be modified again.
2.
Once the Patrol Tour has been de-activated, the Patrol Tour Setup page will also
become unchangeable. Instead of re-configuring a new Patrol Tour from the beginning,
you can use the Copy Patrol Tour button
to create a new patrol tour with the same
settings as the de-activated Patrol Tour.
69
7.3 Monitoring Patrol Activities
To monitor Patrol activities, click Monitoring on the menu bar and select New Patrol Tour
Monitor. This dialog box appears.
Figure 7-7
Next, click the Filter button
and select the Patrol Tour you want to monitor. The current
status of each Patrol Point will be displayed. A red zone indicates Absence, an orange zone
indicates Early or Late, and a green zone indicates On Time.
Figure 7-8
70
7
7.4
Patrol Tour
Accessing Patrol Log
Using Patrol Log, you can set search criteria to look up patrol records. Refer to 10.1
Connecting to GV-ASManager to see how to log into GV-ASWeb.
1. On GV-ASWeb, click the Patrol Log icon
. This window appears.
Figure 7-9
2. In the Filter section on the left, type or select the search criteria. For example, you can
use the Status drop-down list to search for all patrol records listed as “Absence.”
3. Click the Search button to start the log search.
To see how to export logs, refer to 10.3.3 Exporting Logs for details. To see how to customize
the search results columns, refer to 10.3.4 Defining Columns for details.
71
Chapter 8
Other Functions
8.1 Setting Up System User
A system user is a person using the GV-ASManager to monitor door controllers, enroll users
or program the system. Using this function, the system supervisor can create new system
users with different access rights. Up to 1,000 user accounts can be created.
8.1.1
Adding a New User
1. On the menu bar, click Tools and select Operators. This dialog box appears.
Figure 8-1
72
8
2. Click the New button
Other Functions
at the top left corner. This dialog box appears.
Figure 8-2
3. Type the user’s ID and Password. Re-enter the same password in the Password
Confirmation field.
4. Give a Hint (optional) that would remind you of the password.
5. Set the user’s authorization level to Supervisor or User. By default, users belonging to
the Supervisor level have full rights and permissions to system settings. Users belonging
to the User level are restricted from all system settings, and have only limited access to
certain functions.
6. Click OK to add the user.
7. Click the tab ASManager, ASRemote, ASWeb, Database Tool, VMWeb or TAWeb in
the middle of the window. Select the functions to grant access to the system user.
8. In the Data Group section, you can optionally select a data group and specify whether
the user account will be able to read, write and execute the functions assigned under the
data group. A data group may include controllers, cards, users, access groups, time
zones and weekly schedules. Up to 32 data groups can be created. You can click the
name of the data group to type a different name.
„
Read: Privilege to view settings.
„
Write: Privilege to view and change settings. When Write is selected, Read will
automatically be selected.
„
Execute: Privilege to open door, close door and turn off alarm.
For example, if you select Data Group 4 and only select Write, the user will be able to
view and change only the settings of the controllers, cards, users, access groups, time
zones and weekly schedules assigned under Data Group 4.
9. If you select Allow Password Removing System, you can erase all user and supervisor
accounts by running AccessPassUninstall.exe in the folder where the GV-ASManager
program was installed.
73
8.1.2
Editing an Exiting User
Only supervisors are allowed to edit the information of a system user.
1. Select a user from the user list to display its properties. Or, right-click on a user level
(User or Supervisor), and then select Find Specific Account for a quick search. A valid
password is required to edit a supervisor.
2. Edit the properties as required. Check the Account Is Disabled option if you wish to
disable this user.
74
8
Other Functions
8.2 Setting Up Alert Notification
When alarm conditions occur the system can automatically send SMS alerts and e-mail alerts
to one or multiple recipients, as well as activating computer alarm.
8.2.1
Setting SMS Server
Before you can send out SMS alerts, you should configure the SMS server.
1. On the menu bar, click Tools and select SMS Server Settings. This dialog box appears.
Figure 8-3
2. Type the IP address of the SMS server, its login username and password. Then assign
up to three mobile numbers, including country code, which SMS alerts should be sent to.
Click OK.
3. To enable the SMS connection, click Tools on the menu bar and select Connect to SMS
Server.
Note: For ASCII encoding (English language), SMS text messages are limited to 160
characters; for Unicode encoding (other languages), SMS text messages are limited to 70
characters. If you want to send longer text messages, select Send more than one sms if
content is too long. The long messages will be split up to 9 segments and go out as multiple
SMS messages.
75
8.2.2
Setting E-Mail Server
Before you can send out e-mail alerts, you should configure the e-mail server.
1.
On the menu bar, click Tools and select Email Server Settings. This dialog box
appears.
Figure 8-4
2.
Set up the following options:
„
Name: Type the sender’s name.
„
E-Mail Address: Type the sender’s e-mail address.
„
Authentication: If your mail server requires authentication for sending e-mails,
select one type of authentication, and type the valid username and password.
„
Host Name/Address: Type the name of the mail server.
„
Command Port: Keep the default port 25, or modify it to match that of the mail
server.
„
SSL: Enable the Secure Sockets Layer (SSL) protocol to ensure the security and
privacy of Internet connection. When the option is enabled, the Command Port is
changed to 465.
„
Message Priority: Assign the message a priority so the recipient knows to either look
at it right away (high priority) or read it when time permits (low priority). A high priority
message has an exclamation point next to it. Low priority is indicated by a down
arrow.
„
Send to: Type a valid e-mail address and click the Test button to check if the server
setup is correctly configured.
76
8
8.2.3
Other Functions
Setting Notification
1. On the menu bar, click Tools and select Notifications. This dialog box appears.
Figure 8-5
2. Click the Access, Event, LPR or Hotlist tab to set the alert methods for different events.
3. Select an event.
4. For Access and LPR tabs, you can clear the check mark for All Access Groups and
select a specific access group. The alert will only be set off when specified event is
triggered by members of that access group.
77
5. On the right, select the alert methods:
„
Invoke Alarm: Enable the computer alarm when the selected event occurs.
„
Send E-Mail Alert: When you select this option, an e-mail will pop up. Enter the
recipient’s e-mail address and alert subject. Then you can enter your own content, or
use the buttons on the text window to send out the programmed information
automatically.
button, the sent SMS alert will include the controller
For example, if you click the
information. For details see C. E-Mail and SMS Alert Symbols in Appendix.
„
Send SMS Alert: When you select this option, a dialog box will pop up. Ensure the
preset mobile number(s). Select Text Code Type. Then type your messages;
otherwise click the buttons on the text window to send out the programmed
information automatically. See the above example in “Send E-Mail Alert”.
„
Trigger Recording: Enable recording of DVR, Video Server or Compact DVR when
the selected event occurs. You can specify the recording time between 1 and 300
seconds. For the function to work, you must activate monitoring on these IP devices
ahead.
„
Popup Message: An associated live view will pop up for alert when the selected
event occurs. You can specify the duration of the live view remains on the screen
between 1 and 300 seconds.
„
Trigger Preset: Direct the camera(s) to a preset point when the selected event
occurs.
„
Run Application: Specify the Application Path and the designated application will
run when the selected event occurs. You can also type a command in the
Application Parameter field to execute a function of that application.
6. To define more than one event with the same alert configuration, first right-click the
previously defined event on the list and select Copy to save its settings. Then use Ctrl +
left click or Shift + left click to select several events. Right-click the selected events and
select Paste to have the same settings.
Note: For text code type, select ASCII for English that is limited to 160 characters and select
Unicode for text of other languages that is limited to 70 characters.
78
8
Other Functions
8.3 Startup, Backup and Export Setup
To access the Auto Startup, Auto Backup and Export to File functions, click Tools on the
menu bar and select Option. This dialog box appears.
Figure 8-6
„
Run at Startup: Run GV-ASManager at Windows startup.
„
Auto Backup: You can also specify a path for the Auto Backup function to
automatically save another copy of log and image files. The Auto Backup function
performs backup at 24:00 A.M every day. By default, the log and image files are
saved at C:\Access Control\ASManager\ASBackup.
„
Export to File: Access data will be exported to text files at the specified storage path
and can then be utilized by 3rd party programs. The access data will be listed in the
file name of the text files. Up to 5000 files can be stored.
[At Startup]
„
Remote Monitor Server: Enable Remote Monitor Server upon GV-ASManager
startup. Remote Monitor Server needs to be enabled to utilize GV-ASRemote.
„
Web Server: Enable Web Server upon GV-ASManager startup. Web Server needs
to be enabled to access GV-ASWeb.
79
„
GeoFinger Server: Enable GeoFinger Server upon GV-ASManager startup.
GeoFinger Server needs to be enabled to enroll fingerprints remotely through
TCP/IP.
„
Connect to SMS Server: Enable SMS Server upon GV-ASManager startup. SMS
Server needs to be enabled to receive alert notifications through SMS messages.
Note:
1.
Web Server and GeoFinger Server options are selected by default.
2.
To back up the Configuration files, see 14.3 Other Database Settings.
80
8
Other Functions
8.4 Setting Up GV-GF Fingerprint Readers
GV-ASManager can enroll users’ fingerprints using GV-GF1911 / GV-GF1921 / GV-GF1922
and upload the fingerprint data to the GV-GF Fingerprint Readers installed on the
controllers. To gain access, the user’s fingerprint must match the enrolled fingerprint.
Note: GV-GF1911 / 1912 / 1921 / 1922 is only supported in GV-ASManager 4.0 or later.
For details on how to enroll fingerprints and how to upload fingerprint data to GV-GF
Fingerprint Reader, refer to Chapter 3 Fingerprint Only Mode in the GV-GF Fingerprint
Reader User’s Manual.
81
8.5 Scanning Driver’s Licenses and Business Card
GV-ASManager can work with SnapShell ID Scanner to let you acquire and edit the
personal data from driver’s licenses and business cards.
Note: This function only supports SnapShell ID Scanner with SDK driver version.
1. Consult the Scanner’s documentation to connect the Scanner with the GV-ASManager.
2. On the menu bar, click Personnel and select Users. The User List dialog box appears.
3. Click the New button. The User Setup dialog box appears.
4. Click the Scan tab. This dialog box appears.
Figure 8-7
5. In the File Type field, select Driver License or Business Card. Here we use the Driver
License as the example to demonstrate the following steps.
82
8
Other Functions
6. Place a driver’s license on the Scanner and click Scan. The license image is displayed.
Figure 8-8
7. Click the Extract button to read the license data. The data is displayed in the Value
column.
8. To modify the data, click the desired Value column and type the next texts. Click
anywhere in the dialog box when you are finished with the modification.
Figure 8-9
9. Click the Update button. This driver’s license is saved to the GV-ASManager’s database.
10. Now you can click the Home tab to view the information of the driver’s license, or click the
Business tab to view the information of the business card if scanned.
83
8.6 Setting Hot Keys to Quickly Control Doors
You can assign hot keys to quickly control individual or multiple doors to perform one of the
commands below: Unlock door, lock down, force lock, force unlock, disable door lock
operation.
1.
On the menu bar, click Tools and select Hot Key Settings. This dialog box appears
Figure 8-10
2.
Under the Device list, select the GV-ASManager, a controller, or a door and select the
command you want to assign a hot key.
3.
Next to List of hotkeys, select the hot key and click Assign. If the hot key is already
assigned, the assigned command will be listed under Hotkey currently used by.
4.
84
Click OK.
8
Other Functions
8.7 Defining New Card Formats
By default, GV-ASManager only recognizes identification cards of certain bit formats that
have been pre-defined. To use cards with other data formats, you will need to define the card
format so that GV-ASManager can recognize it.
1.
On the menu bar, click Personnel and select Code Format Settings. The pre-defined
card formats are listed.
Figure 8-11
85
2.
To define a new card format, click the New button. This dialog box appears.
Figure 8-12
3.
Next to Select Card Bits, select the card bit.
4.
For each number under Card Bit, define whether it is Parity, Facility Code or Card
Number by clicking the Add button. The exact steps to defining card format vary from
card format to card format.
5.
86
When you are done, click OK.
9
Chapter 9
GV-ASRemote
GV-ASRemote
The client software GV-ASRemote is designed to monitor multiple GV-ASManagers over the
network. The GV-ASRemote provides the following features:
•
Remote monitoring
•
Remote live view and playback
•
Remote control: stop alarms and force the door to lock/unlock
9.1 Installing GV-ASRemote
Insert Software DVD to your computer and a window will pop up automatically. Select Install
GeoVision Access Control System, click GeoVision Access Control System and follow
on-screen instructions to complete the installation.
9.2 The GV-ASRemote Window
Figure 9-1
87
No. Name
Function
1
Menu Bar
The Menu Bar includes the options of File (log in / out the
GV-ASManager), Monitoring (display monitor windows of
alarm, access and event), View (display the function
windows) and Window (arrange the display of different
windows).
2
Toolbar
The Toolbar includes the options of Connect, Disconnect,
Auto Connect, Add Host, Remove Host, Settings and
Resolution.
3
Device View
Displays a list of connected doors and their current status.
4
Alarm Monitor
Displays alarm events of doors.
5
Event Monitor
Displays monitored events of doors.
6
Access Monitor
Displays access activities of doors.
7
MultiView
Displays live views of connected cameras from multiple IP
devices. For details, see 5.4 The MultiView Window.
8
Information Window
Displays the information of doors, card readers and monitored
events.
9
Playback
Plays back recorded events from a compatible GeoVision IP
device. For details, see the same operations in 5.5 Retrieving
Recorded Video.
10
Live Video
Displays live views of one connected camera. For details, see
the same operations in 5.2 Accessing Live View.
11
Camera List
Displays a list of connected cameras.
88
9
9.2.1
GV-ASRemote
Toolbar
Figure 9-2
The buttons on the Toolbar of GV-ASRemote:
No. Name
Function
1
Connect
Starts the connection with the GV-ASManager.
2
Disconnect
Ends the connection with the GV-ASManager.
3
Auto Connect
Retries to build the connection with the GV-ASManager.
4
Add Host
Adds a GV-ASManager host to the list.
5
Remove Host
Deletes a GV-ASManager host on the list.
6
Settings
Edits the settings of GV-ASManager hosts.
7
Resolution
Changes the size of icons to 16 x 16, 24 x 24 or 32 x 32.
89
9.3 Connecting to GV-ASManager
Before GV-ASRemote may connect to one GV-ASManager, the GV-ASManager must allow
the remote access by this procedure:
•
Click Tools on the menu bar, select Servers and enable Remote Monitor Server.
When the server is started, the icon
appears at the bottom of the main screen.
To create a GV-ASManager host and enable connection to the GV-ASManager:
1. On the toolbar, click the Add Host button. This dialog box appears.
Figure 9-3
2. Give a hostname, type the GV-ASManager’s IP address, modify the port number if
necessary, and type the GV-ASManager’s login ID and password.
3. Click Add. This dialog box appears.
Figure 9-4
4. Type the ID of the controller associated with the GV-ASManager and click OK.
5. To add more controllers, repeat Steps 3-4.
90
9
GV-ASRemote
6. Click OK and return to the main screen. A host folder will be displayed on the Device
View window as example below.
Figure 9-5
appears, it indicates the connection between GV-ASManager and
If the icon
GV-ASRemote has been established.
If the icon
appears, it indicates the connection failed. Make sure GV-ASManager is
enabled for the Remote Monitor Server function.
Note: For the disconnection messages displayed on the Status column (Figure 4-7), see D.
Controller Status in Appendix.
91
Chapter 10
GV-ASWeb
The GV-ASWeb allows you to access data and settings on the GV-ASManager over the
network. Connecting to one GV-ASManager at a time, users can remotely watch live video,
view event data, download logs in different formats, and set up camera / cards / users /
vehicles / controllers / schedule using Web interface.
To use the GV-ASWeb, the version of browser in the client PC must be Internet Explorer 7
or later.
10.1 Connecting to GV-ASManager
Before GV-ASWeb can connect to a GV-ASManager, the GV-ASManager must be set to
allow remote access:
•
On the menu bar, click Tools, select Servers and enable Web Server. This dialog box
appears.
Figure 10-1
If you want to grant or deny the access from certain IP addresses, click Add, and type the
IP addresses. Otherwise click OK to start the connection. When the server is started, the
icon
92
appears at the bottom of the main screen.
10
GV-ASWeb
To start the GV-ASWeb:
1. There are two ways to link to GV-ASWeb:
z
Under the device list, right-click the PC and click ASWeb or ASWeb with SSL.
Figure 10-2a
z
Open an Internet browser, and type the IP address of the GV-ASManager to be
connected. This web page appears.
Figure 10-2b
2. Click https:// for SSL encrypted connection, or ASWeb for regular connection.
93
3. Enter a valid username and password for login. The GV-ASWeb page appears.
Figure 10-3
94
10
10.2
GV-ASWeb
Accessing Live Video
You can use GV-ASWeb to remotely watch live video of devices connected to the
GV-ASManager.
1.
On GV-ASWeb, click the Live Video icon
. This window appears.
Figure 10-4
2.
Click the Device drop-down list to select a connected GV-System or LPR.
3.
Use the Camera drop-down list to select a camera. The live view will now be displayed.
Note: Live video will be displayed using MJPEG codec and a frame rate of 5 fps.
95
10.3
Accessing Logs
You can access the logs of the connected GV-ASManager, including Access Log, Daily
Access, Alarm Log, Event Log and I/O Log. In addition, you can set up search criteria to view
the records more efficiently.
Figure 10-5
10.3.1
Setting Search Criteria
1.
Select a log you want to view. Here we use Access Log as an example.
2.
In the Filter section on the left, type or select the desired filtering criteria. For example,
we want to search the log for the records that match the conditions of “Access Granted”,
Card Number “120-38620”, Gate A entrance of AS400, and dates from November 21st to
November 27th. The resulting filter window may look like this.
Figure 10-6
3.
96
Click the Search button to start the log search.
10
10.3.2
GV-ASWeb
Log Window Icons
The icons in the log window can display the detailed information of that category. Click the
icon to view the details.
: Indicates the availability of the recorded video.
: Indicates the availability of the video image.
In Controller List, Card List, User List, Access Log and Daily Access, you can right-click each
search result to access more information such as card information
information
or user
.
Note: You can play back video only when Remote ViewLog Service included in Control
Center Server is enabled on the DVR. And the Remote ViewLog function is enabled on Video
Server or Compact DVR.
10.3.3
Exporting Logs
You can download the logs of the connected GV-ASManager to the current computer in four
formats: .txt, .html, .xls and html (zip).
1.
Use the Export drop-down list on the top-right corner and select the file format TXT,
HTML, Excel and HTML (ZIP).
2.
Use the next drop-down list to select This Page to save the current log page or All to
save all logs.
3.
Click OK to download the logs.
10.3.4
Defining Columns
You can define the displayed columns of the search results for each type of log. The field
must be first enabled on GV-ASManager before the content of the field can become
searchable.
97
1.
On the menu bar of the GV-ASManager, click Tools and select ASWeb Field. This
dialog box appears.
Figure 10-7
2.
Select the fields you would like to enable and click OK.
3.
On GV-ASWeb, click on the arrow next to an existing column and select Columns.
Figure 10-8
4.
Select a field to display it in the search results.
For example, we added a user-defined field “Parking Space Number” to the Access Log.
The resulting window on the GV-ASWeb may look like this:
Figure 10-9
98
10
10.4
GV-ASWeb
Adding and Deleting Controllers
You can use GV-ASWeb to remotely add or delete controllers to the GV-ASManager.
1.
On GV-ASWeb, click the Controller List icon
. This window appears.
Figure 10-10
2.
Click the Add button
to add a new controller. For details on the configurations, refer
to Step 1: Configuring a Controller in Chapter 4.
3.
To set the individual doors, click the Edit button
and select a door. For details, refer
to Step 2: Configuring the Doors or Elevator Floors in Chapter 4.
Figure 10-11
4.
To delete a controller, select a controller and click the Delete button
.
Note: After adding or deleting a controller through GV-ASWeb, the change will be reflected
in the Controller List in GV-ASManager.
99
10.5
Adding and Deleting Cards and Users
In addition to adding and deleting controllers, you can also use GV-ASWeb to remotely add
or delete cards and users.
To add or delete cards:
1.
On GV-ASWeb, click the Card List icon
2.
Click the New button. This dialog box appears.
.
Figure 10-12
3.
Fill out the required information. Refer to 4.3 Setting Cards for more details.
4.
Click OK to save the settings.
5.
If you have a GV-PCR310 Enrollment Reader installed, you can click Card Reader
to add a card using GV-PCR310.
Figure 10-13
100
10
6.
GV-ASWeb
To delete cards, simply select the card and click the Delete button.
Note:
1. After adding or deleting a card through GV-ASWeb, the change will be reflected in the
Card List in GV-ASManager.
2. The Batch function and the card data import/export function are not supported on
GV-ASWeb.
101
To add or delete users:
1.
On GV-ASWeb, click the User List icon
2.
Click the New button. This dialog box appears.
. The User List window appears.
Figure 10-14
3.
Type the user’s name. Other user information such as Employee ID, Home information
and Business information are optional.
to assign a card or a vehicle to the user.
4.
You can click the Add button
5.
You can use the Data Group drop-down list to assign the user to a data group.
6.
If you have a webcam installed, click the Webcam icon
Webcam for the user profile.
7.
Click OK to save the settings.
8.
To delete a user, simply select the user and click the Delete button.
to take a picture from the
You can enroll fingerprints in the Fingerprint tab using GV-GF1911 / 1921 / 1922. For details,
refer to Chapter 3 Fingerprint Only Mode in the GV-GF Fingerprint Reader User’s Manual.
102
10
GV-ASWeb
Note:
1. After adding or deleting a user through GV-ASWeb, the change will be reflected in the
User List in GV-ASManager.
2. The user data import / export function is not supported on GV-ASWeb.
3. The webcam function requires Flash Player 10 or later.
103
10.6 Searching, Adding and Deleting IP Cameras
You can use GV-ASWeb to remotely search and set up IP cameras by connecting to
GV-Systems, GV-Video Servers, GV-Compact DVR or to IP cameras directly.
1.
On GV-ASWeb, click the Camera List icon
2.
To search for available IP devices under LAN, click the Search button
. The Camera List window appears.
and select
Search DVR and NVR or Search IP Device. This dialog box appears.
Figure 10-15
A. Select the GV-Systems or IP devices to add from the search results.
B. If necessary, you can select a different Network Adaptor and click the Search
button again or modify the default port number 15000.
C. Click Add. The GV-System or IP device is added to the camera list on the left.
D. To login, select the GV-System or IP device, click the Edit Mode button
type the User ID and password.
104
, and
10
3.
To manually add a device, click the Add button
GV-ASWeb
. This dialog box appears.
Figure 10-16
A. Select the Type of device to add and type a Host Name to name the device.
B. Type the IP Address, User name and Password of the device.
C. Modify the default Data Port 5611, default VSS Port 10000, and default Log Port
5552 if necessary.
D. For IP cameras, use the Brand drop-down list to select the camera model. You can
connect to third-party IP cameras through ONVIF, PSIA and RTSP protocols by
selecting Protocol in the Brand drop-down list.
E. For GV-Systems, GV-Compact DVR and GV-Video Server, select a number from the
Number of Cameras drop-down list to add channels between channel 1 and the
selected channel. For example, if 3 is selected, channels 1-3 will be added.
F. Click Save.
and select a device to begin editing.
4.
To edit a device, click the Edit button
5.
To delete a device, select the device and click the Delete button
.
Note: After adding or deleting a camera through GV-ASWeb, the change will be reflected in
the Camera List in GV-ASManager.
105
10.7 Setting Schedule
You can use GV-ASWeb to remotely create daily schedules, set up weekly schedule and
specify holidays. For more details on how to set up schedule, refer to Chapter 4.
10.7.1
1.
Setting Daily Schedule
On GV-ASWeb, click the Time Zone Setup icon
. This dialog box appears.
Figure 10-17
2.
Click the Add button
. A blank schedule appears.
Figure 10-18
3.
Type an ID and a name for the daily schedule.
4.
Set the time by dragging the mouse on the timeline. To erase selected time, click the
Delete Access Time button
106
and drag the mouse across the selected time.
10
5.
GV-ASWeb
You can use the Data group drop-down list to assign the time zone to a data group. You
can then allow or forbid a user to read/write the functions listed under the data group.
Refer to Adding a New User in Chapter 8 for more details.
6.
Click Update to save.
10.7.2
1.
Setting Weekly Schedule
On GV-ASWeb, click the Schedule Setup icon
. This dialog box appears.
Figure 10-19
2.
Click the Add button
3.
Type an ID and a name for the weekly schedule.
4.
You can use the Data Group drop-down list to assign the weekly schedule to a data
. A blank schedule appears.
group. You can then allow or forbid a user to read/write the functions listed under the
data group. Refer to Adding a New User in Chapter 8 for more details.
5.
Click the timeline and assign the daily schedule created to the day of the week. The
schedule selected for Holiday will be applied to the dates selected in the Holiday Setup
page. Refer to the section below.
6.
Click Save.
107
10.7.3
Specifying Holiday
On the main page of GV-ASWeb, click the Holiday Setup icon
. To specify holidays,
click Add Holiday and click the dates of the Holiday. To remove holidays, click Remove
Holiday and click the dates.
Figure 10-20
10.8 Setting Access Groups
Using GV-ASWeb, you can remotely set up access groups to restrict who can access which
door at what time. On the main page of GV-ASWeb, click the Access Groups icon
For details on how to set up access groups, refer to Setting Access Groups in Chapter 4.
Figure 10-21
108
.
10
10.9
GV-ASWeb
Setting Door Groups
Using GV-ASWeb, you can remotely organize controllers into different door groups, allowing
you to quickly upload fingerprints to all controllers in a door group at once.
On the main page of GV-ASWeb, click the Door Group Setup icon
. For details on
how to set up door groups and upload fingerprints, refer to Uploading Fingerprints to
Controllers Using Door Groups in Chapter 3 of GV-GF Fingerprint Reader User’s Manual.
Figure 10-22
109
10.10 Configuring Areas for Anti-Passback
You can remotely define Entry and Exit areas for each door / gate using GV-ASWeb.
1.
On GV-ASWeb, click the Area Settings icon
. This dialog box appears.
Figure 10-23
2.
Click the Add button to add an area and double-click the name to rename the area.
3.
Double-click a door and use the drop-down lists to assign the entry and exit area.
Figure 10-24
For more details on how to set up Anti-Passback, refer to Chapter 6.
Note: After defining areas for Anti-Passback through GV-ASWeb, the change will be
reflected in the Area Settings page in GV-ASManager.
110
10
GV-ASWeb
10.11 Creating Maps
You can place the icons of connected controller, LPR lanes, and LPR cameras on the Google
Maps or on a map you uploaded to GV-ASWeb. The map will help you quickly pinpoint the
location of an event or the devices you have installed.
1.
On GV-ASWeb, click the Map icon
. This dialog box appears.
Figure 10-25
2.
On the Google Maps, zoom in on location of the building or the monitored area. Skip to
step 6 if you do not want to upload your own map.
3.
To upload your own map, click Add Map. This dialog box appears.
Figure 10-26
to locate the file of the map.
4.
Type a name for the map and click the Add button
5.
Click Upload. A pin is placed on the map.
6.
Click Edit in the top-right corner. If you have uploaded your own map, click the pin to
open the map.
111
7.
Drag the controller, LPR lane, and LPR camera icons from the left menu onto the map
according to their location.
8.
Click Edit again when you are finished. You can click the icon of the controllers, LPR
lanes or LPR cameras to access their information.
Figure 10-27
Next, you can look up activities at a door or LPR lane by clicking the arrow button
top-right corner. Select your search criteria and click Search.
Figure 10-28
112
in the
10
GV-ASWeb
• You can double-click an event to locate the associated door or LPR lane on the map.
• You can select Route Planning by Google to see the suggested route between the
access data of a card or a license plate in the order of access time.
• To view snapshots or play back recorded videos, click the snapshot or video button
.
On the Google maps, you can also see the directions from one controller / LPR cameras to
another.
1.
Right-click the icon of your starting location, and select Begin.
2.
Add as many destinations as you wish by right-clicking the icon and selecting Through.
3.
For your last destination, right-click the icon and select End.
Figure 10-29
113
10.12 Creating Accounts to Manage GV-ASWeb
The administrator can create accounts with different privileges to manage GV-ASWeb.
1. On the menu bar, click Tools and select Operators. A dialog box appears.
Figure 10-30
2. To create an account, click the New button
in the top left corner.
3. Type the account’s ID and Password. Re-type the password in the Password
Confirmation field.
4. In the Level drop-down list, select Supervisor to have access to all GV-ASWeb functions.
To grant limited access, select User. Click OK.
5. Click the ASWeb tab in the middle.
6. Select the privileges you want to grant. The following options are available.
„ Log: View Alarm Log, Access Log, Daily Access, Event Log and I/O Log.
„ Export: Export Alarm Log, Access Log, Daily Access, Event Log and I/O Log.
„ Image/Playback: Play back recorded videos and snapshots from GV-ASWeb logs.
114
10
GV-ASWeb
„ Access Setup: Set up controller list, camera list, area settings, time zone, schedule,
holidays and user-defined access group.
„ Person Data: Add or edit cards and users.
7. Click OK.
115
Chapter 11
GV-TAWeb for Workforce Schedule and Payroll
GV-TAWeb is a time and attendance management system that helps you assign work
schedule, keep track of employee attendance and calculate salary. You must first enable
GV-TAWeb function on GV-ASManager and then log in GV-TAWeb to access the following
functions:
•
TA Report: Looks up workforce schedule, attendance records, and employee payroll.
•
TA Shift: Sets up different types of daily work schedules.
•
TA Template: Arranges schedules of up to 45 days with daily schedules from TA Shift.
•
TA Holiday: Designates which dates are holidays.
•
TA Schedule: Assigns work schedule to individual or a group of employees.
•
TA User: Specifies employee salary.
To use the GV-TAWeb, the browser in the client PC must be Internet Explorer 7 or later.
116
11
GV-TAWeb
11.1 Connecting to GV-ASManager
To enable GV-TAWeb, the Time Clock option must be enabled on GV-ASManager and the
Web Server must be enabled to allow remote access.
1.
On the menu bar, click Setup, select Devices and in the dialog box, double-click the
GV-AS / GV-EV Controller you want to use to keep track of attendance. Select the Gate
tab and select Time Clock.
Figure 11-1
2.
On the menu bar, click Tools, select Servers and enable Web Server. This dialog box
appears.
Figure 11-2
If you want to grant or deny the access from certain IP addresses, click Add, and type the
IP addresses. Otherwise click OK to start the connection. When the server is started, the
icon
appears at the bottom of the main screen.
117
To start the GV-TAWeb:
1.
Open an Internet browser, and type the IP address of the GV-ASManager to be
connected. This web page appears.
Figure 11-3
2.
Click https:// for SSL encrypted connection, or TAWeb for regular connection.
3.
Enter a valid username and password for login. The GV-TAWeb page appears.
Figure 11-4
118
11
GV-TAWeb
11.2 Setting Up Workforce Schedule
To set up workforce schedule, first set up different types of daily work schedules using TA
Shift, and then you can arrange the different types of daily work schedules into a cycle using
TA Template. Next, specify the dates for holidays in TA Holiday. Lastly, TA Schedule
allows you to assign work schedule to an employee or a group of employees using daily
schedule in TA Shift or using long-term schedule from TA Template.
11.2.1
1.
TA Shift: Setting Up a Daily Schedule
Click the TA Shift icon. This dialog box appears.
Figure 11-5
2.
Click Add Shift to add a new daily shift schedule. This dialog box appears.
Figure 11-6
119
3.
Type a Name for the daily shift to help you identify it.
4.
Select a Start Time and End Time to specify when the work shift starts and ends.
5.
Specify an Advance Period to set the amount of time prior to the regular start time an
employee can work. Employees arriving before the Advance Period will be recorded as
working during Not Scheduled time in TA Record.
6.
Specify an Extended Period to set the amount of time after the regular end time an
employee can work and be counted toward overtime pay.
7.
Specify the Overtime Buffer Period and an employee has to work passed the overtime
buffer period to be counted toward overtime pay.
8.
To specify when break time starts and ends, select Break Time and select the Start
Time and End Time. You can set a second break time if needed. Note that Break Time
will not be counted toward Work Hours.
Figure 11-7
120
11
GV-TAWeb
Using the above figure as an example, an employee working 4 hours passed the 18:00
pm regular end time will receive overtime pay for 4 hours (18:00 - 22:00), while an
employee working 20 minutes passed 18:00 will not receive overtime pay.
Figure 11-8
9.
Click OK to save the shift settings.
121
11.2.2
TA Template: Setting Up a Schedule Template
TA Template allows you to set a 1-45 day recurring schedule template composed of the daily
shift schedule created in TA Shift.
1.
Click the TA Template icon. This dialog box appears.
Figure 11-9
2.
Click Add Template. This dialog box appears.
Figure 11-10
3.
Type a Name to identify the template.
4.
In the Period field, type a number between 1 and 45 to indicate the number of days in
the schedule.
5.
122
Select With Holidays to apply the holidays set up in TA Holiday.
11
6.
GV-TAWeb
In the drop-down list below each day, select a daily shift schedule created in TA Shift.
A TA Template may look like this. In this example, the template is a 2-week work
schedule, because the Period is set to 14 days. The drop-down list under each day
indicates the daily work schedule selected for that day. A blank drop-down list means
that no work schedule is assigned for that day.
Figure 11-11
7.
Click Save.
11.2.3
1.
TA Holidays: Setting Certain Dates as Holidays
Click the TA Holiday icon. This dialog box appears.
Figure 11-12
2.
Select a date and click Add Holiday.
3.
Type a name for the holiday.
4.
Click OK and that day will be designated as a holiday if With Holidays is selected in TA
Template
123
11.2.4
TA Schedule: Assigning Schedules to Employees
After creating daily shift schedules in TA Shift or arranging a schedule template in TA
Template, you can now assign the schedules you set up to an employee or an entire
department and select a start date.
Note: The employees listed in TA Schedule are the users in User List on GV-ASManager.
To assign employees to a department, open the employees’ user information in User List
and select the Business tab. In the Department field, type the department of the employee
and all employees with the same department name will be grouped into one department in
GV-TAWeb.
1.
Click the TA Schedule icon. This dialog box appears.
Figure 11-13
124
11
GV-TAWeb
To assign daily shift schedules day by day:
2.
To assign daily schedules day-by-day, select an employee or a group of employees in
the Company section and click Assign Shift. You can also press Shift or Ctrl to select
multiple employees in a department. This dialog box appears.
Figure 11-14
3.
Select a daily schedule and assign it to a date.
4.
You can choose to apply the schedule to the entire group or only the selected users.
5.
Repeat the steps for all the dates you want to schedule a shift.
6.
Click OK. A TA schedule window may look like this. In this example, different daily
schedules created in TA Shift are assigned from Monday to Saturday to two employees.
Figure 11-15
125
To assign a schedule template:
7.
To assign a schedule template from TA Template, select an employee or a group of
employees and click Assign Template. This dialog box appears.
Figure 11-16
8.
Using the Template drop-down list, select a schedule template created in TA Template.
9.
Select a day from the Template Day of Start Date drop-down list and the template will
start on that day.
Figure 11-17
10. Select a Start Date to begin applying the template and the schedule will begin with the
day specified in Template Day of Start Date. Select an End Date to discontinue the
schedule.
11. In the Schedule Overlapping Scheme section, select Overwrite the original schedule
if you want to overwrite the original schedule in the case of an overlap.
12. Select Keep the original schedule and the template will not be assigned if there is an
existing schedule during the time period you specified.
126
11
GV-TAWeb
13. Click OK. A TA schedule window may look like this. In this example, an FAE weekly
schedule created in TA Template are assigned to two employees.
Figure 11-18
Hint: To set a weekly schedule with Saturday and Sunday as non-working days, set a 7-day
Period and designate two consecutive days as non-working days by not selecting a daily shift.
Figure 11-19
Then, in TA Schedule, match the first non-working day with a Saturday.
Select the first non-working day
Select a Saturday for Start Date
Figure 11-20
127
11.3 TA User: Specifying Hourly Pay
You can specify the hourly pay for regular work hours and overtime work hours using TA
User.
1.
Click the TA User icon. This dialog box appears.
Figure 11-21
2.
Select an employee from the list.
3.
Type the Hourly Regular Pay and the Hourly Overtime Pay.
4.
Click Update to save the settings.
Note: The employees listed in TA User are the users in the User List. To see how to add,
edit or delete users, refer to 4.6 Setting Users.
128
11
GV-TAWeb
11.4 TA Report: Looking Up Records
TA Report allows you to look up workforce schedules, attendance record, payroll and
summaries of each department’s data.
1.
Click the TA Report icon. This dialog box appears.
Figure 11-22
2.
On the left panel, the following data and graphs are available:
Note: Accessing Average Hour Summary, Exception Summary or Payroll Summary
requires Flash Player 10 or later.
[Schedule Templates]
„ Employee Schedule: Shows the work schedule of an individual employee.
„ Unscheduled Employee: Shows the days when employees are not scheduled to
work.
[Time Templates]
„ Daily Time Card: Shows the work schedule and the actual punch in/out time of
employees in a department.
„ Employee Time Card: Shows the work schedule and the actual punch in/out time of
an individual employee.
129
„ Time Card List: Searches for records within a department. To search for normal
activities only, do not select any events. To search for abnormal activities, select one
or more events under the Filter section. The following events are available.
•
In Late: Punching in after the assigned start time.
•
In Early: Punching in before the assigned start time.
•
Out Late: Punching out after the assigned end time.
•
Out Early: Punching out before the assigned end time.
•
Over Hours: Working after the Overtime Buffer Period but before the Extended
Period.
•
Unscheduled Absence: Absence during scheduled work day.
•
Missed Punch: Punching in without punching out or punching out without
punching in.
•
Not Scheduled: Working on days when there is no assigned shift for that day.
„ Average Hour Summary: Shows each department’s average work hours per
person during the time period specified and the percentage occupied in comparison
to other departments.
„ Exception Summary: Displays a department’s total counts of Exception Events
within the time period specified.
[Payroll Templates]
„ Payroll List: Shows the hourly pay, total work hours and total pay of the employees
within a department during the time period specified.
„ Employee Payroll: Shows the hourly pay, total work hours and total pay of an
employee for each day of the time period specified.
„ Payroll Summary: Shows the average total pay of each department during the time
period specified and the percentage occupied within the company.
130
11
3.
GV-TAWeb
Using the Daily Time Card as an example, double-click Daily Time Card on the left
menu. This dialog box appears.
Figure 11-23
4.
Select the Date and Department to look up the employees’ scheduled shift and actual
attendance record.
5.
Click the Run button toward the top. A dialog box similar to the one below appears.
Using the fifth person as an example, Paul punched in at 10:01 and punched out at
16:56, even though his scheduled work time is from 9:00 to 17:00. He is therefore listed
as A (In Late) and D (Out Early) in the Exception column. The number of hours he
worked is listed under the Work Time column.
Figure 11-24
131
6.
You can click the Access Log icon
TA Log icon
to see complete attendance record or click the
to see attendance records excluding records that are not during the
scheduled work hours.
7.
Click Save and a shortcut of the Daily Time Card for the specified department and date
will be created in the TA Report main page.
Figure 11-25
8.
Click Export CSV to export the data in an excel file.
9.
To select which data to display, click the arrow next to the column title and click
Column.
Figure 11-26
Note: The Export CSV function is only available after you have saved the report by clicking
the Save button.
132
11
GV-TAWeb
11.5 Creating Accounts to Manage GV-TAWeb
The administrator can create accounts with different privileges to manage GV-TAWeb.
1. On the menu bar, click Tools and select Operators. A dialog box appears.
Figure 11-27
2. To create an account, click the New button in the bottom left corner.
3. Type the account’s ID and Password. Re-type the password in the Password
Confirmation field.
4. In the Level drop-down list, select Supervisor to have access to all GV-TAWeb functions.
To grant limited access, select User. Click OK.
5. Click the TAWeb tab.
6. Select the privileges you want to grant. The following options are available.
„ Schedule Setting: Access TA Shift, TA Template and TA Schedule.
„ Report viewing: Access TA Report.
„ Payroll settings: Access TA User.
7. Click OK.
133
Chapter 12
GV-VMWeb for Visitor Management
The GV-VMWeb is a visitor management system for internal business use where the
administrator can create a visitor database and grant access to visitors on a LAN
environment. GV-VMWeb can also be set up to allow visitors to register their own visitor
account and create visit requests over the internet using the Visitor service.
Figure 12-1
To use the GV-VMWeb, the browser in the client PC must be Internet Explorer 7 or later.
12.1 Connecting to GV-ASManager
Before GV-VMWeb can connect to a GV-ASManager, remote access must be enabled on the
GV-ASManager as below:
•
On the menu bar, click Tools, select Servers and enable Web Server. This dialog box
appears.
Figure 12-2
134
12 GV-VMWeb
If you want to grant or deny the access from certain IP addresses, click Add and type the
IP addresses. Otherwise click OK to start the connection. When the server is started, the
icon
appears at the bottom of the main screen.
To start the GV-VMWeb:
1.
Open an Internet browser, and type the IP address of the GV-ASManager to be
connected. This web page appears.
Figure 12-3
2.
Click https:// for SSL encrypted connection, or VMWeb for regular connection.
3.
Enter a valid username and password for login. The GV-VMWeb page appears.
Figure 12-4
135
12.2 Creating Accounts to Manage GV-VMWeb
The administrator can create multiple accounts with different privileges to manage each step
of granting access as shown below.
You can create a security staff account with privileges to create Visitor Data and Visit
Records, while another account with privileges to Verify visitors and Issue Card can be
assigned to a management staff. In this setup, the security staff can create a visitor profile
and a visit request for visitors, but the management staff needs to approve the visit and issue
a card to the visitor before the visitor can be granted access.
Note: You need to create a visitor card before you can issue a card to a visitor. To see how
to add a visitor card, refer to 4.3 Adding Cards.
To create accounts:
1. On the menu bar, click Tools and select Operators. This dialog box appears.
Figure 12-5
136
12 GV-VMWeb
2. To create an account, click the New button in the bottom left corner. This dialog box
appears.
Figure 12-6
3. Type the Supervisor’s ID and Password. Re-type the password in the Password
Confirmation field.
4. In the Level drop-down list, select Supervisor to have access to all GV-VMWeb
functions as shown in Figure 11-6. Click OK. To grant limited access, select User and
click OK.
5. Click the VMWeb tab.
6. Select the privileges you want to grant. The following options are available.
„ Set Up Visitor Data: Create or edit visitor profiles.
„ View Visit Record: Look up visit records in the past for each visitor.
„ Edit Visit Record: Create or edit visits in GV-VMWeb.
„ Approve Visit: Record the name of the account that approved the visit request.
„ Permit Visit: Grant permission to allow the visit in GV-VMWeb.
„ Issue Card: Assign a card to the visitor in GV-VMWeb. The Verify privilege must
also be allowed for the account to have access to this option.
„ System Settings: Enable the Auto-Verify option under Setting drop-down list
.
7. Click OK.
137
12.3 Creating Visitor Profile
GV-VMWeb allows you to create visitors profile and grant different access to each visitor.
To create a visitor account:
1.
In the Visitor section, click the New button. This dialog box appears.
Figure 12-7
2.
In the General tab, you can type the name of the visitor and click Browse to upload a
to take a
photo of the visitor. If you have a webcam installed, click the Webcam icon
picture from the webcam for the visitor profile. Any valid card number and card code for
the visitor will be displayed under the Cards section.
3.
In the Home and Business tab, you can fill out other personal information about the
visitor, such as phone number, address, birthday and gender.
4.
In the User Defined tab, customized field labels will be displayed. To see how to
customize the fields, see 4.6.4 Customizing a Data Field.
5.
Click OK to save the visitor information.
Note:
1.
The visitor profile created will be updated to the User List in GV-ASManager.
2.
The webcam function requires Flash Player 10 or later.
138
12 GV-VMWeb
12.4 Granting Visitor Access
After the visitor’s account is created, access permission can be granted to visitors using the
Demand for Visits section. In this section, you can specify the date and time of the visit,
assign an access card to the visitor and view visit record.
Note: You need to first create a visitor card before you can issue a card to a visitor. To see
how to add a visitor card, refer to 4.3 Adding Cards.
1.
Select the visitor account in the Visitors section and click the New button in the
Demands for Visit section.
Figure 12-8
2.
Select a Visit Date and Visit Time to note the time when the visitor will be visiting.
3.
You can type a Destination and Note for your own reference.
4.
Under Approval, the account that permitted the access will automatically be recorded
after permission is granted.
5.
Select the Permit checkbox to grant access permission.
139
6.
Click the Card Number drop-down list. This dialog box appears.
Figure 12-9
Note: If you have a GV-PCR310 Enrollment Reader installed, you can place the visitor card
on the GV-PCR310 and click Card Reader
7.
to quickly identify the card number.
Select a visitor card to assign to the visitor and use the Deactivation drop-down list to
specify when the card will be deactivated.
8.
Click the Update button to continue editing the Demand for Visit entry.
9.
The Check-In time is the time when the Demand for Visit entry is created. After the
visitor has returned the visitor card, you can return to this visit record and select the
Check-Out checkbox to check out the card. You can also choose to automatically check
out the visitor card when the visitor presents the card at an exit door. Refer to Step 2:
Configuring the Doors or Elevator Floors in Chapter 4 to see how to set up automatic
check out.
Figure 12-10
10. Click the Update button to save the settings and the data will be updated to
GV-ASManager.
140
12 GV-VMWeb
12.5 Searching GV-VMWeb Database
To search for visitors with certain criteria, type the visitor’s information in the Filter section on
the left and click the Search button. The search results will be listed in the Visitors section.
You can also search visit records from the past by using the Search function under Demands
For Visit section. Use the drop-down list to search by Card Number, Destination, Notes or
User.
Figure 12-11
12.6 Visitor Self Registration
Visitors can create a visitor account over the Internet and request permission to access the
premise.
The administrator needs to first set up the mail server on GV-VMWeb. The visitor will be able
to register a visitor account, activate the account and create a visit request. The visit request
will show up in GV-VMWeb for the administrator to grant or deny access.
141
12.6.1
Setting Up Mail Server in GV-VMWeb
The administrator must first set up the mail server in GV-VMWeb. The mail server will be
used to send a confirmation e-mail to the visitor when they register an account.
1.
Open an Internet browser, and type the IP address of the GV-ASManager to be
connected.
2.
Click https:// and then VMWeb for SSL encrypted connection, or VMWeb for regular
connection.
3.
Enter a valid username and password for login. The GV-VMWeb page appears.
4.
In the top-right corner, click System Settings and select Visitor Web.
Figure 12-12
5.
Under the Servers tab, set up the mail server.
Figure 12-13
„ SMTP Server Address: Type your mail server’s URL address or IP address.
„ Login Name / Password: Type the login name and password of the mail server.
„ SSL: Select SSL if your e-mail server requires the SSL authentication for
connection.
142
12 GV-VMWeb
„ Port: Keep the default port 25 or type a new port number for webmail providers that
may use different SMTP port such as Yahoo and Hotmail.
„ HTTP Server Address: Type the IP address or the domain name of the
GV-ASManager.
6.
Click the Confirmation E-Mail tab and type the Sender Name, Sender Address, Mail
Subject and Mail Message. After registering a visitor account, a confirmation e-mail will
be sent to the visitor and the visitor must click the activation link to confirm the account.
Figure 12-14
7.
Click the Password E-Mail tab and fill out the information. The visitor will be able to
retrieve a forgotten password by clicking the “Forgot your password?” link at the login
page. An e-mail with the password will be sent to the visitor.
143
12.6.2
1.
Creating a Visitor Account
Open an Internet browser, and type the IP address of the GV-ASManager to be
connected. This web page appears.
Figure 12-15
2.
Click https:// and then Visitor for SSL encrypted connection, or Visitor directly for
regular connection. The Visitor Login page appears.
Figure 12-16
144
12 GV-VMWeb
3.
Click Register a Visitor Account. This window appears.
Figure 12-17
4.
Type the e-mail address and type a password for the visitor account.
5.
Type the characters for word verification.
6.
Click Submit. A confirmation e-mail will be sent to the e-mail address shortly. Click the
activation link in the e-mail to activate the visitor account.
12.6.3
Creating a Visit Request
After the visitor account is activated, the visitor can now log into his or her account to create a
visit request.
1.
Open an Internet browser, and type the IP address of the GV-ASManager to be
connected. A web page appears.
2.
Click https:// and then Visitor for SSL encrypted connection, or Visitor directly for
regular connection. The Visitor Login page appears.
3.
Type the visitor account and password, and click Login. This window appears.
Figure 12-18
145
4.
Click the Visitor Setting button to complete the visitor profile. Refer to Creating Visitor
Profile earlier this chapter for more details.
5.
Click the Add Visit button. This dialog box appears.
Figure 12-19
6.
Specify the planned visit date and time.
7.
Click Save.
When the administrator logs into GV-VMWeb, he or she can click the visitor’s name to see
the visit request submitted.
Figure 12-20
The administrator can double-click the visit request to grant access and assign visitor card to
the visitor.
146
13 License Plate Recognition
Chapter 13
License Plate Recognition
The License Plate Recognition functions allow GV-DSP LPR and GV-DVR LPR to grant
access when the detected license plate numbers match the vehicle registered in
GV-ASManager’s database. GV-ASManager can connect with up to 255 GV-DSP LPR and /
or GV-DVR LPR, which can recognize license plates detected in the connected cameras.
Video Source
Plate Recognition
Setting & Database
1 ch
Analog Camera
GV-DSP LPR
GV-ASManager
Analog Camera
8 ch
LPR
Recognition
GV-DVR LPR
IP Camera
Computer installed with
GV-System
LPR Plugin
GV-USB Dongle
Figure 13-1
147
Main Screen
Figure 13-2
148
13 License Plate Recognition
13.1 Installing GV-DVR LPR
A GV-System V8.5.5.0 or later can be turned into a GV-DVR LPR simply by installing the
LPR Plugin supplied in the Software DVD and by inserting an LPR Dongle.
13.1.1
System Requirements
Before setting up GV-DVR LPR, make sure the PC meets the minimum system requirements.
Number of LPR Channels
1-4 Channels
5-8 Channels
OS
64-bit Windows 7 / 8 / Server 2008 / Server 2012
CPU
Core i5 2400, 3.1 GHz
Memory
2 x 2 GB Dual Channels
Hard Disk
500 GB
VGA
AGP or PCI-Express, 1280 x 1024 , 32-bit color and support
Core i7 2600, 3.4 GHz
DirectX 10c
DirectX
End-User Runtimes (November 2008)
Software
.NET Framework 3.5
SQL Server 2005 Express (optional)
Browser
Internet Explorer 7.0 or later
GV-System
GV-ASManager 4.0: V8.5.5.0 or V8.5.6.0
GV-ASManager 4.1: V8.5.7.0
GV-ASManager 4.2: V8.5.8.0
GV-ASManager 4.2.1: V8.5.9.0
Note:
1.
The software programs End-User Runtimes (November 2008) and .NET Framework 3.5
are required to run the GV-ASManager. The software programs can be found in the
supplied software DVD.
2.
It is recommended to use separate PCs for GV-ASManager and GV-DVR LPR.
149
13.1.2
Installing LPR Plugin
1. Insert the supplied Software DVD to your computer and a window pops up automatically.
Figure 13-3
2. Select Install LPR Plugin and follow on-screen instructions to complete the installation.
13.1.3
Inserting LPR Dongle
To see recognition results, an LPR Dongle needs to be inserted to the computer of the
GV-System. Both internal and external dongles are available. The dongle options include 1, 2,
3, 4, 5, 6, 7, 8 channels.
The following types of USB Dongle are supported:
•
GV-LPR with GV-System (Black, Blue)
•
GV-LPR with Video Capture Card (Black, Blue)
Note:
1.
When multiple LPR dongles are inserted, the dongle that supports the most number of
channels will be applied. The number of channels supported on each dongle will not be
combined.
2.
If no LPR dongle is inserted, license plates will be captured but the plate numbers will
not be recognized.
150
13 License Plate Recognition
13.1.4
Accessing Recognition Results on GV-DVR LPR
LPR Plugin comes with a tool that allows you to access the snapshots and recognized plate
numbers of the detected license plate. When installing LPR cameras for the first time, you
can use this tool to see the recognition results and make sure the cameras have been set up
correctly.
1. Open the folder of the GV-System and click TestRecogPicView.exe. This dialog box
appears.
Figure 13-4
2. Click Show. The upper row is the live view of channels 1 to 4 and the lower row shows
the snapshots of any license plates detected. The recognized plate numbers are
displayed under the snapshots.
Figure 13-5
3. To see the results from channels 5 to 8, click Switch Page to switch to page 2.
4. To manually force the GV-DVR LPR to detect license plates, click the channel number
on the right. You may need to switch to the correct page first to see the
buttons
recognition results.
151
13.2 Setting Up GV-DVR LPR
To set up GV-DVR LPR, follow the requirements listed in 12.1 Installation and then follow the
steps below:
•
Step 1 Enabling LPR Functions on GV-DVR LPR
Enable the recognition cameras and/or the overview cameras on GV-DVR LPR.
•
Step 2
Adding GV-DVR LPR to GV-ASManager
Establish the communication between GV-ASManager and GV-DVR LPR.
•
Step 3 Configuring a Channel
Set up the related cameras and the recognition conditions of the channel.
Note: For optimal results, the recognition cameras should be cameras specialized for
license plate recognition, such as GeoVision’s GV-LPR Cam 20A, GV-LPR Cam 10A, and
GV-Hybrid LPR Cam 10R. For more information, visit GeoVision’s website at:
http://www.geovision.com.tw/english/3_1_LPR.asp.
152
13 License Plate Recognition
13.2.1
Step 1: Enabling LPR Functions on GV-DVR LPR
To enable license recognition on GV-DVR LPR, click the Configure button, select Video
Analysis, select License Plate Recognition to access the following LPR related functions.
Figure 13-6
„
Enable LPR Service: Enable recognition of license plates detected in the Recognition
Camera.
„
Enable Overview Camera Service: Allow GV-ASManager to use cameras connected
to the GV-System as overview camera.
„
Auto Start LPR Service: Automatically start LPR Service at GV-System Startup.
„
Auto Start Overview Camera Service: Automatically start Overview Camera Service
at GV-System Startup.
„
Configure: Allows you to export LPR data. See Exporting LPR Data section below.
Note: Make sure the LPR dongle is inserted to the computer of the GV-System.
153
13.2.2
Step 2: Adding GV-DVR LPR to GV-ASManager
1. On the menu bar, click Setup and select Devices. This dialog box appears.
Figure 13-7
2. On the right LPR side, click the Add button
Figure 13-8
3. Type an ID number and Name for the LPR.
4. Use the drop-down list to select DVR-LPR.
154
. This dialog box appears.
13 License Plate Recognition
5. Click OK. This dialog box appears.
Figure 13-9
6. Assign the GV-DVR LPR to a Data Group if needed or select No Groups to disable the
data group function. You can then allow or forbid a user to read / write / execute the
functions assigned under the data group. Refer to Adding a New User in Chapter 8 for
more details.
7. Under Connection, type the IP Address, User name and Password of the GV-DVR LPR.
8. You can modify the following settings if necessary.
„
Command Port: The default command port is 3388.
„
Data Port: The default data port is 5611.
„
Log Port: The default log port is 5552.
„
Number of Cameras: Select the number of cameras supported by the GV-System.
„
Camera Name: On the right side of the dialog box, select a camera to modify the
camera name.
9. Under LPR Engine, select the Country of the recognition engine. You can also modify
the log-related settings to change how and what information is stored for debug purposes.
155
13.2.3
Step 3: Configuring a Channel
1. To configure the channel, select a Lane tab. This dialog box appears.
Figure 13-10
2. Select Enable.
Note: To apply the current settings of the connected GV-DVR LPR, click Sync from DVR
LPR and skip to step 9.
3. Select up to four cameras connected to the GV-System to be the Recognition Camera.
Having more than 1 camera is useful when the width of the lane requires multiple
cameras. If multiple cameras recognize the same license plate at the same time, the data
will be recorded as 1 record. Note that the resolution of the recognition camera needs to
be at least D1.
156
13 License Plate Recognition
4. Select up to three Overview Cameras to capture the overall appearance of the vehicle.
The overview camera must be connected to the GV-System.
5. Configure the Recognition Settings:
„
Recognition: Select to start license plate recognition upon motion detection or
I/O trigger.
„
Matching Mode: To open the output device specified in Barrier Control only when
the detected license plate matches a registered license plate completely, select All
Characters Match. When Allow 1 mismatched character or Allow 2
mismatched characters is selected, 1 or 2 mismatched characters will be
tolerated and the order of the characters will be ignored. For example, license plate
ABC-123 will be considered matching with ZZC-321 when Allow 2 mismatched
characters is selected.
„
Sensitivity: Adjust the sensitivity level for motion detection.
6. Adjust the Recognition Region Setup for each camera if needed: Only license plates
inside the area drawn will be recognized.
7. Use the Barrier Control drop-down list to select an output device. The output device will
be triggered when the detected license plate matches a registered license plate according
to the Matching Mode set in step 5.
8. Select Do not record unrecognized results to omit unrecognized results from LPR log.
9. Under Recognition Engine, adjust the settings below to improve recognition accuracy.
„
Recognition loop number: Repeat recognition for the number of times specified.
„
Max. / Min. characters: Set the maximum or minimum number of characters on
the license plate to activate the recognition process. If the number of characters
exceeds the maximum or is under the minimum, the system will not start the
recognition.
„
Max. / Min. height of characters: You can set the maximum and minimum height
of characters on the license plate in pixels to activate the recognition process.
„
Enable rotation detection: License plates tilted horizontally can be detected.
„
Enable fast rotation detection: This option can increase the recognition speed by
10 % but decrease the accuracy by 3%.
„
Max. / Min. rotation detection angle: Set the maximum and minimum tilt angle to
be allowed to activate the recognition process.
„
Enable Slant Detection: License plates tilted vertically can be detected.
„
Max. / Min. slant detection angle: Set the maximum and minimum tilt angle to
activate the recognition process.
157
„
Detect 2 line license plate: Recognize two rows of characters on license plates.
Note this option is only available on the engine version of V5000 or later.
„
Detection number of license plates: Set the maximum number of plates to be
recognized simultaneously.
„
Default plate background color: Select Light to only recognize plates with white
characters on dark background or select Dark to only recognize plates with dark
characters on white background. This function is only supported when Global or
China is selected for Country.
„
Invert plate background color: Select Enable to invert plate color when the
license plate cannot be recognized. This function is only supported when Global or
China is selected for Country.
„
Replace I with 1: Always identify the character “I” as “1” (one).
„
Replace zero with O: Always identify the character “0” as “O” (letter O).
„
Replace Q with zero: Always identify the character “Q” as “0” (zero). Note this
option is only available on the engine version of V5000 or later.
„
License Plate Rule: You can customize up to six license plate rules and the
recognized plates will be converted similar character to follow the rule. The rule
must be between 4 and 9 characters and consists of “A” (Alphabets), “D” (Numeric
digits) and “X” (Any). For example, if the rule is AA-DDDD, a license plate detected
as XY-123A will be converted to XY-1234 to follow the rule. The rule will be ignored
if none of the detected plate numbers follow the rule.
10. Click OK to apply the settings and return to the main screen. An LPR folder tree will be
displayed on the Device View window as example below.
If the icon
appears, it indicates the connection between the GV-DVR LPR and
GV-ASManager has been established.
If the icon
appears, it indicates the connection failed. Make sure the above
connection setup is correctly configured.
Figure 13-11
158
13 License Plate Recognition
Note:
1. The Overview Cameras need to be set to round-the-clock recording on GV-System.
2. To ensure optimal performance, the total number of Overview Cameras supported in a
GV-System is limited based on the resolution of the overview cameras:
•
Overview camera: D1 = maximum 16 overview cameras
•
Overview camera: 1 MP = maximum 8 overview cameras
•
Overview camera: 2 MP = maximum 4 overview cameras
•
Overview camera: 3 MP = maximum 3 overview cameras
•
Overview camera: 4 MP = maximum 2 overview cameras
•
Overview camera: 5 MP = maximum 1 overview camera
3. To open a gate when the detected license plate is recognized as a registered vehicle:
a. Set up I/O devices on the GV-DVR LPR (Configure button > Accessories > I/O
Device > I/O Device Setup). Refer to 6.1 I/O Device Setup on the DVR User’s
Manual to see how to set the gate as the output device.
b. Select the output device under Barrier Control.
159
13.2.4
Exporting LPR Data
You can export LPR data to other equipments, such as a parking lot ticket machine. There
are two ways to export the data, through RS-232 connection or export into a file that can be
imported into a third-party program. On GV-DVR LPR, click the Configure button, select
Video Analysis, select License Plate Recognition, select Configure and click Export
Setting.
Figure 13-12
Export through RS-232
1.
If you are connecting the computer to your equipment using RS-232 connection, click
the Export Through RS232 tab and select Enable Export through RS232.
Figure 13-13
160
13 License Plate Recognition
2.
Next to Select Port, select the COM port that is used for connection.
3.
Under Select Recognition Items to Export, select the LPR data you want to export.
4.
Under Length (Bytes), you can click the number to specify the length of the data you
want to display.
5.
Under Recognition Time Export Format, select how detailed you want the time
information to be.
6.
Under Export Content Format, you can add text or symbols to the beginning or the end
of the LPR data. You can also separate each item with the text or symbol specified.
7.
Click OK.
Export Into a File
1.
To export a TXT file to your equipment, click the Export to File tab and select Enable
File Export.
Figure 13-14
2.
Select a storage Path to store the exported file by clicking the … button.
3.
Under File Extension, you can change the default txt file extension if needed.
161
4.
To select what items to export, click Select Export Item button.
Figure 13-15
a. Select the items you want to export.
b. Use the Recognition Time Export Format to select how you want to display the
recognition time.
c. Use the Plate Region Export Format drop-down list to specify how you want to
display the position of the license plate detected.
d. Click OK.
162
13 License Plate Recognition
5.
Under File Name Setting,
•
You can use a Fixed File Name.
•
To define your own file name, select User Define and click the Define File Name
button. Next, select the data you want listed in the file name.
Figure 13-16
6.
To add the new export data to the end of the existing export file, click Add data to the
end of the existing export file. If this option is not selected, the old data will be
overwritten.
7.
Click OK.
163
13.2.5
Recognition Engine Version
GV-DVR LPR V4.2.1 only supports the following versions of recognition engines:
No.
Country
Engine Version
No.
Country
Engine Version
1
Argentina
6.0.1.6
23
Italy
6.0.0.2
2
Australia
4.2.1.1
24
Malaysia
6.0.0.3
3
Austria
6.0.1.6
25
Mexico
4.4.5.6
4
Belgium
6.0.1.6
26
New Zealand
6.0.1.6
5
Brazil
6.0.1.6
27
Norway
6.0.1.1
6
Bulgaria
6.0.1.6
28
Poland
6.0.1.6
7
Canada
4.0.4.0
29
Portugal
6.0.1.6
8
Channel Islands
4.0.3.8
30
Qatar
3.1.2.2
9
Chile
3.2.0.9
31
Russia
6.0.1.7
10
China
4.2.1.3
32
Serbia
4.0.3.8
11
Columbia
4.2.1.5
33
Slovakia
6.0.1.6
12
Croatia
4.0.3.8
34
Slovenia
4.0.3.8
13
Cyprus
4.0.3.8
35
South Africa
6.0.0.9
14
Czech
6.0.1.6
36
Spain
6.0.1.6
15
France
6.0.1.6
37
Taiwan
4.5.5.7
16
Germany
6.0.1.6
38
Thailand
2.3.0.8
17
Global
6.0.1.6
39
Turkey
4.0.3.8
18
Hong Kong
6.0.1.2
40
UAE
2.3.0.8
19
Hungary
6.0.1.5
41
UK
6.0.1.6
20
India
4.2.1.1
42
USA
4.2.1.2
21
Ireland
6.0.1.5
43
Vietnam
4.2.1.0
22
Israel
3.1.2.2
164
13 License Plate Recognition
13.3 Setting Up GV-DSP LPR
To set up GV-DSP LPR functions on the GV-ASManager, follow the steps below.
Note:
•
GV-ASManager V4.1 is only compatible with GV-DSP LPR firmware V2.0 and V2.0.1.
•
GV-ASManager V4.2 is only compatible with GV-DSP LPR firmware V2.0.2.
•
GV-ASManager V4.2.1 is only compatible with GV-DSP LPR firmware 2.0.3
•
Step 1 Enabling Connection with GV-ASManager on GV-DSP LPR
Enable connection with GV-ASManager on GV-DSP LPR.
•
Step 2
Adding GV-DSP LPR to GV-ASManager
Establish the communication between GV-ASManager and GV-DSP LPR.
•
Step 3 Configuring a Channel
Set up the related cameras and the recognition conditions of the channel.
13.3.1
Step 1: Enabling Connection with GV-ASManager on GV-DSP LPR
To enable connection with GV-ASManager on GV-DSP LPR, first make sure a mini or micro
SD card is inserted to the GV-DSP LPR and formatted. Next, log in the Web interface of the
GV-DSP LPR and follow the steps below.
1. In the left menu under Events and Alerts, select Registry Database. This dialog box
appears.
Figure 13-17
165
2. Select Enable Registry Database.
3. Use the Registry Database Comparison drop-down list to select one of these options:
„
Complete (All Characters Match): Detected license plate must match a registered
license plate completely.
„
Like (One Character Mismatch): 1 mismatched character will be tolerated and the
order of the characters will be ignored. For example, license plate ABC-123 will be
considered matching with ZBC-321.
„
Somewhat Like (Two Characters Mismatch): 2 mismatched characters will be
tolerated and the order of the characters will be ignored.
4. Click the Apply button.
To set the Recognition Engine and recognition conditions, recognition sensitivity for example,
refer to the Detection Mode and Recognition Engine Settings in Chapter 4 of the GV-DSP
LPR User Manual.
To open a gate when the detected license plate is recognized as a registered vehicle, refer to
4.2.2 Output Setting on the GV-DSP LPR User Manual to see how to set the gate as the
output device.
166
13 License Plate Recognition
13.3.2
Step 2: Adding GV-DSP LPR to GV-ASManager
1. On the menu bar, click Setup and select Devices. This dialog box appears.
Figure 13-18
2. On the right LPR side, click the Add button
. This dialog box appears.
Figure 13-19
3. Type an ID number and Name for the LPR.
4. Use the drop-down list to select DSP-LPR.
167
5. Click OK. The LPR Setup page appears.
Figure 13-20
6. Assign the GV-DSP LPR to a Data Group if needed or select No Groups to disable the
data group function. You can then allow or forbid a user to read / write / execute the
functions assigned under the data group. Refer to Adding a New User in Chapter 8 for
more details.
7. Under Connection, type the IP Address, User name and Password of the GV-DSP LPR.
8. You can modify the following settings if necessary.
168
„
Https Port: The default Https port is 443.
„
VSS Port: The default VSS port is 10000.
13 License Plate Recognition
13.3.3
Step 3: Configuring a Channel
1. To configure the channel, select the Lane 1 tab. This dialog box appears.
Figure 13-21
2. Select Enable.
3. Select up to three Overview Cameras to capture the overall appearance of the vehicle.
The overview camera must be connected to a GV-System and the GV-System needs to
be added to the camera list:
a. Right-click the GV-System in the Camera List and select Settings.
b. Click the Add button and select Add DVR Mapping.
c. Type the connection information of the overview camera and click OK.
4. Select a Playback Camera, usually the same camera as the Recognition Camera. The
playback camera also needs to be connected to a GV-System and the GV-System needs
to be added to the camera list. You can select an event in the monitor window, and
GV-ASManager will play back the camera view recorded at the time of the event. Refer to
Retrieving Recording Video in Chapter 5 for details.
5. Click OK to apply the settings.
169
Recognition conditions, area, and associated output device can be set up on the Web
interface of the GV-DSP LPR. Refer to the Recognition Engine Settings section in Chapter 4
of the GV-DSP LPR User Manual.
Note:
1. The Playback Cameras need to be set to recording on GV-System in either
round-the-clock mode or upon motion detection.
2. The Overview Cameras need to be set to round-the-clock recording on GV-System.
3. To ensure optimal performance, the total number of Overview Cameras supported in a
GV-System is limited based on the resolution of the overview cameras:
170
•
Overview camera: D1 = maximum 16 overview cameras
•
Overview camera: 1 MP = maximum 8 overview cameras
•
Overview camera: 2 MP = maximum 4 overview cameras
•
Overview camera: 3 MP = maximum 3 overview cameras
•
Overview camera: 4 MP = maximum 2 overview cameras
•
Overview camera: 5 MP = maximum 1 overview camera
13 License Plate Recognition
13.4
Adding Vehicles
Once you have set up the GV-DVR LPR or GV-DSP LPR, you will need to create a vehicle
database. The detected license plate number must match the license plate number of a
registered vehicle before access can be granted.
1. There are two ways to add a vehicle:
•
When an unregistered vehicle is detected, the message Plate Recognized:
Unregistered Vehicle is displayed. Right-click the message and select New / Edit
Vehicle. The Adding a New Vehicle dialog box appears with the detected license
plate number (Figure 13-23).
•
On the menu bar, click Personnel and select Vehicles. This dialog box appears.
Figure 13-22
171
2. Click the New button on the toolbar. This dialog box appears.
Figure 13-23
3. The settings are available for the card:
„
User: Assign the vehicle to a user.
„
License Plate: Type the license plate number of the vehicle.
„
Brand / Model / Color: Specify the brand, model and color of the vehicle if needed.
„
Ticket: You can type a note for your own reference.
„
Vehicle Status: Set the vehicle status to be Active or Inactive. The Deactivation
Date, if enabled, will override the selection here.
„
Activation/Deactivation Date: Specify a time to activate and deactivate the
vehicle access.
172
13 License Plate Recognition
„
Access Group: Access Groups control which vehicle can access which channel
and at what time. For details, see 4.5 Setting Access Groups.
For first-time users of the GV-ASManager, the access group is not yet established.
Select User Define for test run.
„
LPR: The LPR column displays the associated channels. The selection for each
channel will be automatically brought up if an access group was selected.
When setting up LPR functions for the first time, select 24-hour access for each
channel for test run.
„
Data Group: Assign the vehicle to a data group or select No Groups to disable the
data group function. You can then allow or forbid a user to read/write/execute the
functions listed under the data group. Refer to Adding a New User in Chapter 8 for
more details.
To assign multiple vehicles to a user, click Personnel on the menu bar and select Users.
Next to Vehicle List, click the Add button to assign vehicles to the user.
Figure 13-24
You can also import and export vehicle data in mdb or xls format. Refer to 4.3.3 Importing /
Exporting Card Data for similar settings.
173
13.5 Monitoring LPR Activities
13.5.1
LPR Device View
The LPR Device View displays the connection status of the connected LPRs. To open the
LPR Device View, click View on the menu bar and select LPRs.
Figure 13-25
Right-click an LPR to access the following options:
Name
Function
Reconnect
Reconnects with the LPR.
Sync LPR
After modifying the LPR settings, clicking Sync LPR will renew the
settings immediately.
Settings
Accesses the LPR setup dialog box.
Right-click an LPR channel to access the following options:
Name
Unlock Door
Function
Opens the gate barrier for the time period specified for the output
device. Make sure the gate barrier has been set up as the designated
output device. For GV-DVR LPR, refer to the Barrier Control option in
13.2.3 Step 3: Configuring a Channel. For GV-DSP LPR, see the
Output Setting section in Chapter 4 of the GV-DSP LPR User Manual.
Settings
174
Modifies the controller settings in the Controller Setup dialog box.
13 License Plate Recognition
13.5.2
Monitoring Windows
To monitor LPR activities, click Monitoring and select New LPR Monitor. This dialog box
appears.
Figure 13-26
For details on the Monitoring Windows, refer to 3.3 Monitoring Windows.
175
13.6 Receiving Notifications for LPR Activities
When alarm conditions occur, the system can automatically send e-mail and SMS alerts to
one or multiple recipients.
To set up LPR or vehicle hotlist notifications, click Tools, select Notifications, and click the
LPR or Hotlist tab. This dialog box appears. Select an event to start setting up alert methods.
Figure 13-27
For detailed settings, refer to 8.2 Notification Setup.
176
13 License Plate Recognition
13.7 Setting Up Vehicle Hotlist
The vehicle hotlist is a list of stolen vehicles or other vehicles of interest. There are three
ways to add vehicles to the hotlist: manually add vehicles, import from vehicle list or import
from an external database. Up to 2-million vehicles can be added to the vehicle hotlist.
Setting Up the Hotlist Database
To import from a database, you need to complete the steps below first.
1. Run ASDBManager.exe from the GV-ASManager program folder at :\Access
Control\ASManager\.
2. Select Settings from Source to ASManager Database and select Set the mapping
relations for vehicle hotlist. This dialog box appears.
Figure 13-28
177
3. Use the Source Database drop-down list to select if you want to use the same database
as other data, an excel database or other types of database.
4. Select the path of the database and click Open.
5. Next to Select a source table, select the appropriate tab in the database.
6. Match the License Plate, Group Name and Memo to the appropriate fields.
7. Click OK to import.
Adding Vehicles to the Hotlist
1. On the menu bar of GV-ASManager, click Personnel and select Hotlist. This dialog box
appears.
Figure 13-29
2. Under the Group section, click the Add button
to create a hotlist group if needed. If
you have imported data from an external database using ASDBManager, the vehicles will
be listed under the Default group already.
178
13 License Plate Recognition
3. To add vehicles to the hotlist manually, click the Add button
under Vehicle Hotlist and
type the License Plate. You can add a Memo to note the stolen time and location.
Figure 13-30
4. Click Add.
5. To import an existing license plate from the vehicle list, click the Import button
.
Figure 13-31
6. Select the vehicles you want to add and click Select.
When GV-ASManager recognizes a license plate that matches a license plate in the hotlist,
the vehicle will be highlighted in red in the LPR Monitor window as shown below.
Figure 13-32
179
13.8 LPR Functions in GV-ASWeb
Using GV-ASWeb, you can connect to GV-ASManager over network and remotely access
the following LPR functions:
•
LPR List: Adds and deletes GV-DVR LPR or GV-DSP LPR to / from GV-ASManager.
•
Vehicle List: Adds, deletes, edits and searches vehicles.
•
LPR Log: Searches records of license plate detected and plays back recordings.
•
Access Group Setup: Sets up access groups to restrict who can access which channels
at what time.
Refer to 10.1 Connecting to GV-ASManager to see how to log into GV-ASWeb.
180
13 License Plate Recognition
13.8.1
LPR List
You can use LPR List to remotely add and delete a GV-DVR LPR or a GV-DSP LPR to
GV-ASManager, set up channels and delete an LPR.
1.
On GV-ASWeb, click the LPR List icon
. This window appears.
Figure 13-33
2.
Click the Add button
to add an LPR. For details on the settings, see 13.2.2 Adding
GV-DVR LPR to GV-ASManager and 13.3.2 Adding GV-DSP LPR to GV-ASManager.
3.
and select a channel. For
To set the individual channels, click the Edit button
details on the configurations, refer to 13.2.2 and 13.3.2 Configuring a Channel.
4.
To delete an LPR, select an LPR and click the Delete button
.
Note: After adding or deleting an LPR through GV-ASWeb, the change will be reflected in
the LPR List in GV-ASManager.
181
13.8.2
Vehicle List
Vehicle List allows you to remotely add, search, edit and delete vehicles.
1.
On GV-ASWeb, click the Vehicle List icon
2.
Click the New button
.
. This dialog box appears.
Figure 13-34
3.
Fill out the required information. Refer to 13.4 Adding Vehicles for more details.
4.
Click OK to save the settings.
5.
To delete a vehicle, simply select the vehicle and click the Delete button.
Note: After adding, editing or deleting a vehicle through GV-ASWeb, the change will be
reflected in the Vehicle List in GV-ASManager.
182
13 License Plate Recognition
13.8.3
LPR Log
Using LPR Log, you can set search criteria to look up a record, see snapshots of detected
license plates and play back recorded videos.
Setting Search Criteria
In the Filter section on the left, set the search criteria and click the Search button.
For example, we want to search for records that match the log message of “Unregistered
Vehicle”, license plate number “FM-0505”, and detected by LPR 1 this month. The resulting
filter window may look like this.
Figure 13-35
If Fuzzy Matching is selected, the letters below will be recognized as numbers:
„
Letter B will become 8
„
Letter Z will become 2
„
Letter O and D will become 0 (Zero)
„
Letter I will become 1
„
Letter S will become 5
„
Letter G will become 6
When a license plate number is typed in the Recognized Plate field, you can apply Fuzzy
Matching and the Matching Mode you set will be applied as well (e.g. Allow 1 mismatched
character). When a license plate number is typed in the License Plate field, only the license
plate that matches completely will be displayed in the search results.
183
Search Results Window
Below is an example of a search results window.
Figure 13-36
A snapshot of the detected license plate will be displayed.
: Indicates the availability of the recorded video.
: Indicates the availability of the video image.
You can right-click each search result to access more information such as vehicle information
or user information
.
To see how to export logs, refer to 10.3.3 Exporting Logs for details. To see how to customize
the search results columns, refer to 10.3.4 Defining Columns for details.
Note: You can play back video only when Remote ViewLog Service included in Control
Center Server is enabled on the DVR. And the Remote ViewLog function is enabled on Video
Server or Compact DVR.
184
13 License Plate Recognition
13.8.4
Access Group Setup
Using GV-ASWeb, you can remotely set up access groups to restrict who can access which
channel at what time. On the main page of GV-ASWeb, click the Access Groups icon
. For details on how to set up access groups, refer to Setting Access Groups in
Chapter 4.
Figure 13-37
185
Chapter 14
GV-Access Mobile Applications
GV-Access Mobile Applications allow you to access up to 5 GV-ASManagers through an iOS
or Android mobile device. The following functions are supported:
•
Watch camera live view from GV-System or GV-DVR LPR mapped with a door or lane
•
Lock or unlock a door
•
Check door status to see if alarm events have occurred
•
Open an LPR lane
Supported Operating Systems:
•
Android version V4.1.2
•
iOS version V6.14
14.1 Installing GV-Access
To install GV-Access on your mobile devices, search and download GV-Access in Android
Play Store or Apple App Store. The GV-Access icon will appear on the desktop of your
mobile device.
Figure 14-1
186
14 GV-Access Mobile Applications
14.2 Connecting to GV-ASManager
Tap the GV-Access icon
on the desktop of your mobile device. There are three tabs
on the bottom: Controller, LPR and Config.
1. Tap the Config tab and tap the Add button
.
Figure 14-2
2. Type a Name to help you identify the GV-ASManager and type the IP address, Port, login
Account and Password.
3. Tap Test Login to test the connection with GV-ASManager.
4. Tap Add to add the GV-ASManager.
187
14.3 Managing Controllers
After adding GV-ASManager to GV-Access, the controllers and doors associated with the
GV-ASManager will be listed under the Controller tab.
1. Tap the Controller tab.
Figure 14-3
The authentication mode is listed under each door: card mode, card or password mode,
card and password mode, and release mode. When you remotely control the doors using
GV-Access, the action taken will be listed instead until Disable Door Operation is
selected.
188
14 GV-Access Mobile Applications
The following icons are available.
Icon
Description
Icon
Description
Connected
Camera(s) available
Disconnected
Control door(s)
Note: To access camera live view, the camera(s) associated with the door must be
connected to a GV-System or GV-DVR LPR.
The following alert icons are available. When alert conditions occur, the alert icon will light
up in red. To clear the alert, tap the red icon and select OK.
Icon
Description
Icon
Description
Alarm
Fire Alarm
Force Open
Held Open
Duress
Tailgating
Tamper
Access Denied
Note:
1.
GV-EV48 Elevator Controller only supports the Duress alert icon. The remaining alert
icons are not functional for GV-EV48.
2.
The Tailgating function is currently not functional.
2. To remotely control the door(s), tap the Control button
and select one of the
following options. If you use the Control button next to a GV-ASManager, the command
will apply to all connected doors.
„
Unlock Door: Unlock door temporarily.
„
Force Unlock: Unlock door until Disable Door Operation is selected.
„
Force Lock: Lock door until Disable Door Operation is selected.
189
„
Disable Door Operation: Cancel Force Unlock, Force Lock or Lock Down
command.
„
Lock Down: Lock the door, and the door can only be opened by presenting the
correct access card.
Note: The Lock Down function is not supported in GV-EV48 Elevator Controller.
3. Tap a door to access its live view if available. You can tap Switch Camera if there are
multiple cameras connected to the door.
Figure 14-4
190
14 GV-Access Mobile Applications
14.4 Managing LPR
After adding GV-ASManager to GV-Access, the GV-DVR LPR and GV-DSP LPR associated
with the GV-ASManager will be listed under the LPR tab.
1. Tap the LPR tab. The connected LPR and lanes appear.
Figure 14-5
The following icons are available.
Icon
Description
Icon
Description
Connected
Camera(s) available
Disconnected
Control door(s)
Note: To access camera live view, the camera(s) associated with the lane must be
connected to a GV-System or GV-DVR LPR.
191
2. To remotely unlock the LPR lane, tap the Control button
and select Unlock Gate.
3. Tap a lane to access its live view if available. You can tap Switch Camera if there are
multiple recognition cameras connected to the lane.
Figure 14-6
192
15
Chapter 15
Database Settings
Database Settings
Before you can run GV-ASManager, it is required to create a database or to upgrade your old
database to fit the latest version of GV-ASManager. You can select either a Microsoft Office
Access or Microsoft SQL Server to be the database of GV-ASManager.
If a database already exits, the GV-ASManager provides you the Source Database function
to convert various database formats to be the GV-ASManager’s (Access or SQL Server).
15.1 Starting the Database Tools
To start the Database Tools, you may use one of the methods:
1. If you log in the GV-ASManager for the first time, this message will pop up: “Cannot open
database. Would you like to set up database?”. Click Yes. The following Database Tools
dialog box will appear.
2. If you have run the GV-ASManager, run ASDBManager.exe from the program folder to
access the Database Tools.
Figure 15-1
193
15.2 Creating a Database
You can select either Microsoft Office Access or Microsoft SQL Server as the database of
GV-ASManager.
1. Click the ASManager Database Setting button on the Database Tools dialog box (Figure
15-1).
2. Click the Setup MDB/MSSQL Database for ASManager button. This dialog box
appears.
Figure 15-2
3. To use Access as the database, select Microsoft Office Access Database and click OK.
The database is created in the local computer.
4. To use SQL Server as the database, select Microsoft SQL Server.
a. Under the SQL Database Setting, type IP address or domain name of the SQL
server in the Data Source field, and select its authentication way.
b. Under the Database, name the databases for Configuration files and Log files that
will be created on the SQL server separately.
c. Click Test Connection to test the connection to the SQL server.
d. Click OK. The databases are created in the SQL server.
194
15
Database Settings
15.3 Other Database Settings
You can upgrade, delete, back up and remove the database of GV-ASManager. Click
ASManager Database Setting button on the Database Tools dialog box (Figure 15-1) to
display the following dialog box and have further settings.
Figure 15-3
[Upgrade to latest database version] If an old database exits on the local computer, select
this option to upgrade the version of the old database to the latest.
[Delete ASManager Database] Removes the database from the local computer or the SQL
Server.
[Backup Database] Backs up the Configuration file.
[Recovery Database] Restores the backup Configuration file to the current computer or
import it to another computer.
Note: To automatically back up Log and Image files, use the Auto Backup function. See 8.3
Startup, Backup and Export Setup.
195
15.4 Mapping Source Database
The Source Database function can convert OLE DB and Active Directory database into
GV-ASManager (Access or SQL Server) database. Click the Setting from Source to
ASManager Database button on the Database Tools dialog box (Figure 15-1). This dialog
box appears.
Figure 15-4
Under the Setting Menu:
[Set Connection] Configures the connection to an active directory or an OLEDB provider.
[Set Mapping] Maps the user, cards, vehicle or hotlist fields between the GV-ASManager
database and the source database.
[Input/Modify the auto-update time setting] Specify a time to update the database
automatically.
196
15
Database Settings
Under the Update Menu:
[Update User Data manually] Update the user data manually.
[Update Card Data manually] Update the card data manually.
[Update Vehicle Data Manually] Update the vehicle data manually.
[Update Vehicle Hotlist Manually] Update the vehicle hotlist manually.
197
15.5.1
1.
Converting Data from the Active Directory Database
Click the Set Connection button on the Options dialog box (Figure 15-4). The Source
Database dialog box appears.
2.
Select Active Directory. This dialog box appears.
Figure 15-5
3.
If you log in the local computer with the authorized username and password from the
source database server, select Bind as currently logged on user and type the IP
address or domain name of the server. If not, select Bind with credentials, type the IP
address or domain name of the server and its login username and password.
4.
Ensure the Port number matches that of the source database server.
5.
Select Default Root Node to connect to the root node of the source database.
Otherwise, select This Node and specify the node path.
6.
Click Test Connection to connect to the source database server.
7.
Click the Update Cardholder Data manually button in the Options dialog box (Figure
15-4) to convert the cardholder data from the source database to the GV-ASManager
database immediately.
8.
Click the Update Card Data manually button in the Options dialog box (Figure 15-4) to
convert the card data from the source database to the GV-ASManager database
immediately.
9.
To update the database automatically later, click the Input/Modify the Auto-update
time setting button in the Options dialog box (Figure 15-4) and specify the time in
minutes.
198
15
15.5.2
Database Settings
Converting Data from the OLE Database
To convert data from the OLE database, you need to go through these instructions:
•
Connect an OLE database
•
Map the cardholder data
•
Map the card data
•
Convert the data from the source database
To connect an OLE database:
1.
Click the Set Connection button on the Options dialog box (Figure 15-4). The Source
Database dialog box appears.
2.
Select Other Database. This dialog box appears.
Figure 15-6
199
3.
Select the OLE DB provider that you wish to connect to, and click OK. The connection
dialog box appears. The dialog box varies depending on the OLE DB provider you
choose. Here we select Microsoft OLE DB Provider for SQL Server as example.
Figure 15-7
4.
Type the IP address or domain name of the source database server, select its login
authentication method, and select a specific database on the server. Click Test
Connection to connect to the source database server.
200
15
Database Settings
To map the cardholder data:
1.
Click the Set the mapping relations for cardholders button in the Options dialog box
(Figure 15-4). This window appears.
Figure 15-8
2.
Click the Add button to select a related table on the source database.
3.
Click the
buttons to map each field of GV-ASManager database to a corresponding
field of the source database.
4.
In the following steps, we demonstrate how to map the Name filed as example. lick
the
button in the Name field. This dialog box appears.
Figure 15-9
201
5.
In the left side of the mapping field dialog box, select the field(s) of the source database
corresponding to the Name field of the GV-ASManager database. Then click Add. In this
example (Figure 15-9), the Contact ID field of the source database corresponds to the
Name filed of the GV-ASManager database.
6.
If the field of the source database, without having the data entered, is linked to an index
or another table, click the Set Foreign Key button. This dialog box appears.
Figure 15-10
7.
When the foreign key dialog box is open, the linked Primary Key Table and Primary
Key Field should be displayed if the connection of the Foreign Key Table and Primary
Key Table has been created. Otherwise, use the drop-down lists to select the Primary
Key Table and Field.
8.
In the left side of the foreign key dialog box, select the field(s) of the Primary Key Table
corresponding to the field of the Foreign Key Table. In this example (Figure 15-10), the
Contact ID field of “Human Resource (Employee)” Foreign Key Table is linked to the
First Name, Middle Name and Last Name fields of “Person (Contact)” Primary Key
Table.
9.
Click OK. In the Mapping Setting window, you can see the mapping results. In the
example (Figure 15-8), the Name field of the GV-ASManager database is mapped to the
Contact ID field of the source database which includes First Name, Middle Name and
Last Name (which are linked from the Primary Key Table).
202
15
Database Settings
To map the card data:
1.
Click the Set the mapping relations for cards button in the Options dialog box (Figure
15-4). This window appears.
Figure 15-11
2.
Select a related table on the source database.
3.
Click the Field Name column on the right side to map each field of the GV-ASManager
database and the source database.
To convert the data from the source database:
1.
Click the Update Cardholder Data manually button in the Options dialog box (Figure
15-4) to convert the cardholder data from the source database to the GV-ASManager
database immediately.
2.
Click the Update Card Data manually button in the Options dialog box (Figure 15-4) to
convert the card data from the source database to the GV-ASManager database
immediately.
3.
To update the database automatically later, click the Input/Modify the Auto-update
time setting button in the Options dialog box (Figure 15-4) and specify the update time.
203
Chapter 16
Net Module Utility
With the Net Module Utility included in Software DVD, you can change settings and update
the firmware of the GV-AS / GV-EV Controller.
1. Insert Software DVD, select Install GeoVision Access Control System, click Net
Module Utility and follow the onscreen instructions to install the program.
2. Run Net Module Utility. This window appears.
Figure 16-1
The buttons on the window:
„
Search: Click this button to locate any GV-AS / GV-EV Controller or GV-I/O device on the
same LAN.
„
Set Login: You can select the desired modules from the list, and click this button to log
on to these modules with the same ID and password together.
„
Setting: Click this button to change the Machine Name, IP address, 3DES Code, Device
Port, login ID and password.
„
Advanced Setting: Click this button to directly link to the Web interface of the selected
module.
„
Reboot: Click this button to perform a warm boot of the selected module. This operation
will keep the current configuration.
„
Default: Click this button to reset all configuration parameters to their factory settings.
This may take 5 seconds to complete.
„
Firmware Update: Click this button and assign the firmware file for update.
„
Update to the latest firmware version: The GV-ASManager software comes with the
latest GV-AS / GV-EV Controller firmware. Clicking this button can upgrade your
controller firmware.
204
17 Troubleshooting
Chapter 17
Troubleshooting
Q1: GV-ASManager cannot connect to GV-AS / GV-EV Controller over the
Internet.
There are several causes for this problem such as IP address conflict, incorrect connection
settings and network failure. The following solution is to assign the fixed IP to the
GV-ASManager and GV-AS / GV-EV Controller respectively. This way can determine if the
problem is caused by the faulty devices and incorrect network settings.
1. Disconnect the hub or switch, which connects the GV-ASManager and GV-AS / GV-EV
Controller, from the network.
2. Give the GV-ASManager a fixed IP address that is NOT used by another device, e.g.
192.168.0.154.
Figure 17-1
3. Reset the GV-AS / GV-EV Controller module and Ethernet module to factory defaults.
a. Plug the GV-ASKeypad to the GV-AS / GV-EV Controller.
b. Remove the jumper cap from the 2-pin Default jumper.
c. Press the Reset button.
d. Replace the jumper cap back to the 2-pin Default jumper.
e. To reset the Ethernet Module, press and hold the Default EN button for 6 seconds.
205
4. Open the browser and enter the GV-AS / GV-EV Controller default address:
http://192.168.0.100
Figure 17-2
5. In the IP address field, give the controller an IP address that is NOT used by another
device, e.g. 192.168.0.XXX.
6. On the GV-ASManager, enter the following settings:
Controller ID: 1
Network: TCP/IP
IP: 192.168.0.XXX
Port: 4000
User: admin
Password: admin
Crypto key: 12345678
Figure 17-3
206
17 Troubleshooting
7. The connection between the GV-ASManager and the controller should be established,
and the connection icon
should appear. If disconnection happens after you connect
the hub or switch to the network, then it should be other network problems. Please
contact your network administrator.
Q2: The connection established between the GV-ASManager and GV-AS /
GV-EV Controller is interrupted.
This may be due to IP address conflict. Follow these steps to troubleshoot the problem:
1. Disconnect the hub or switch, which connects to the GV-ASManager and GV-AS / GV-EV
Controller, from the network.
2. Run Windows Command Prompt. Take Classic Windows Start Menu for example, click
Start, select Accessories and click Command Prompt.
3. Type arp –d and press Enter.
Figure 17-4
4. Give the GV-ASManager a fixed IP address that is NOT used by another device. See
Figure 17-1.
5. Open the browser and enter the assigned IP address of the controller. The Network
Configuration page appears. See Figure 17-2.
6. In the IP address field, give the controller an IP address that is NOT used by another
device, e.g. 192.168.0.XXX.
7. On the GV-ASManager, enter the following settings. See Figure 17-3.
Controller ID: 1
Network: TCP/IP
IP: 192.168.0.XXX
Port: 4000
User: admin
207
Password: admin
Crypto key: 12345678
8. The connection between the GV-ASManager and GV-AS / GV-EV Controller should be
established, and the connection icon
should appear. If disconnection happens after
you connect the hub or switch to the network, then it should be other network problems.
Please contact your network administrator.
Q3: GV-ASManager cannot receive card messages but the reader accepts the
card when the connection between the GV-ASManager and GV-AS / GV-EV
Controller is well established.
It may be due to memory failure in the controller. Reset both the controller module and the
Ethernet module to factory settings. Refer to Step 3 in Question 1.
Q4: The GV-ASManager cannot retrieve the video from the DVR for playback.
1. Make sure the Remote ViewLog Service on Control Center Server is enabled on the
DVR.
2. Make sure the time on the GV-ASManager and the DVR is consistent.
3. Make sure the event file you want to play back has been created completely on the DVR.
For example, the assigned time length of every recorded event on the DVR is 5 minutes.
The desired event of 5 minutes must have been displayed on the ViewLog Event List, so
you can access the event file for playback.
Q5: After I add a card by presenting to the reader, the message “Access Denied
Invalid Card” still appears
(For details on adding a card, see Step 1 in 4.3.1 Adding a Single Card.)
It may be the card format is not compatible with the controller. For GV-AS100, GV-AS110,
GV-AS120 and GV-AS400, ensure the format is 26~64 bits. Otherwise, send us the related
information of your card format so that we can customize the format for you.
208
17 Troubleshooting
Q6: The GV-ASManager cannot receive card messages from the GV-Reader
connected to the GV-AS / GV-EV Controller through RS-485 interface.
1. Make sure the GV-Reader is correctly wiring to the controller and Switch 4 on the
GV-Reader is set to OFF.
2. Make sure the correct GV-Reader ID is set on the controller.
Q7: I can’t change the Advanced Settings on the Web interface of the GV-AS /
GV-EV Controller. The “Submit” button is missing.
To modify the Advanced Settings, make sure the Web Setting Switch on the controllers is
set to ON. For the location of the Web Setting Switch, refer to the Web Setting Switch section
of each controller or GV-ASNet / GV-ASBox.
Q8: After installing GV-ASManager, the message “d3dx9_40.dll cannot be
found” appears.
Make sure DirectX End-User Runtimes is installed and restart the computer afterwards. To
install DirectX End-User Runtimes, insert the supplied Software DVD to your computer, and
select Install DirectX End-User Runtimes (November 2008).
Q9: How can I find more help?
Visit our website at http:///www.geovision.com.tw
Write to us at [email protected]
209
Appendix
A.
Compatible IP Devices
This list provides the supported IP device brands. For detailed information on the supported
IP devices, refer to Supported IP Camera List on GeoVision’s Website:
http://www.geovision.com.tw/english/4_21.asp
GeoVision
ACTi
Arecont Vision
AVTech
AXIS
Bosch
Canon
CNB
D-Link
Etrovision
Hikvision
Hunt
IQeye
JVC
LG
MESSOA
MOBOTIX
Panasonic
Pelco
RIVA
Samsung
Sanyo
SONY
UDP
Verint
VIVOTEK
210
Appendix
B. Event Notifications
• “Alarm” events
Type
Description
Force Open
Door <name> is forcibly open.
Duress
Duress function is triggered.
See “Duress” in 1.2 Concepts.
Tamper Inputs are triggered.
Tamper
For hardware settings, see Connecting Input Devices
in GV-AS / GV-EV Controller User’s Manual.
For software settings, see Step 5 in 4.2.2 Step 2:
Configuring the Doors.
Fire Inputs are triggered.
Fire Alarm
For hardware settings, see Connecting Input Devices
in GV-AS / EV Controller User’s Manual.
For software settings, see Step 5 in 4.2.2 Step 2:
Configuring the Doors.
Door <name> is held open over the specified time.
Held Open
See Step 2 and 5 in 4.2.2 Step 2: Configuring the
Doors.
Access Denied
The access is rejected.
• “Access” events
Type
Description
Access Granted
The access from User <name> and Card <Number>
is granted.
Access Denied: Invalid Card
The access is rejected because an unknown card is
presented.
Access Denied: Card suspended
The access is rejected because Card <Number> is
suspended.
Access Denied: Wrong PIN
The access is rejected because the PIN number
entered is wrong.
Access Denied: Card Expired
The access is rejected because Card <Number> is
expired.
Access Denied: Invalid schedule
The access is rejected because the user access is
not on the programmed schedule.
Access Denied: Wrong Door
The access is rejected because the user has access
to the wrong door.
211
Access Denied: APB (Duplicate
Entries)
The access is rejected because the Anti-Passback
rule is violated. Card <Number> is recorded as
successive entries, without exit, to a secure area.
Access Denied: APB (No Entry)
The access is rejected because the Anti-Passback
rule is violated. Card <Number> is recorded as exit,
without entry, to a secure area.
Access Denied: APB (No Exit)
The access is rejected because the Anti-Passback
rule is violated. Card <Number> is recorded as entry,
without exit, to a secure area.
Access Denied: Unknown Card
The access is rejected because the card format is not
compatible.
Access Denied: Invalid Start Date
The access is rejected because Card <Number> is
not enabled.
The access is rejected because the Interlock function
Access Denied: Previous Door Still is violated. The entry door is left unlocked.
Open (Interlock)
See “Interlock” at Step 5 in 4.2.1 Step 1: Configuring
a Controller.
• “Event” events
Type
Description
Force Open
Door <name> is forcibly open.
Duress
Duress function is triggered.
See “Duress” in 1.2 Concepts.
Tamper Inputs are triggered.
Tamper
For hardware settings, see Connecting Input Devices
in GV-AS / GV-EV Controller User’s Manual.
For software settings, see Step 5 in 4.2.2 Step 2:
Configuring the Doors.
Fire Inputs are triggered.
Fire Alarm
For hardware settings, see Connecting Input Devices
in GV-AS / GV-EV Controller User’s Manual.
For software settings, see Step 5 in 4.2.2 Step 2:
Configuring the Doors.
Door <name> is held open over the specified time.
Held Open
See Step 2 and 5 in 4.2.2 Step 2: Configuring the
Doors.
Access Denied
The access is rejected.
Alarm Restored
Alarm sounds are cleared.
Forced Open-Restored
Force Open alarm is cleared.
212
Appendix
Duress Restored
Duress alarm is cleared.
Tamper Restored
Tamper alarm is cleared.
Fire Alarm Restored
Fire alarm is cleared.
Held Open Restored
Held Open alarm is cleared.
Restored Alarm Failed
Fail to clear alarm sounds.
Clear Forced Open Event Failed
Fail to clear Force Open alarm.
Clear Duress Event Failed
Fail to clear Duress alarm.
Clear Tamper Event Failed-No
Event Present
Fail to clear Tamper alarm.
Clear Fire Alarm Event Failed-No
Event Present
Fail to clear Fire alarm.
Clear Held Open Event Failed
Fail to clear Held Open alarm.
Clear Access Denied Failed
Fail to clear Access Denied alarm.
Clear Tamper Event Failed-I/O
Still Unclear
Fail to clear Tamper alarm because Tamper Inputs
remain triggering.
Clear Fire Event Failed-I/O Still
Unclear
Fail to clear Fire alarm because Fire Inputs remain
triggering.
Door Open
Door <name> is open.
Door Close
Door <name> is close.
Door/Gate Unlock
Door <name> is unlocked.
Door/Gate Lock
Door <name> is locked.
Two Person Rule-Active
Two-person A/B rule is active when Card <number>
is presented.
Two Person Rule-Confirm
Two-person A/B rule is confirmed when Card
<name> is presented after the other AB card.
Two Person Rule-Inactive
Two-person A/B rule is violated when Card <name>
is presented successively or the other AB Card isn’t
presented within 20 seconds.
Keypad Code Confirm
On the Card or Common mode, the password
entered is correct.
Wrong Keypad Code
On the Card or Common mode, the password
entered is wrong.
213
Release Mode
Card or Common Mode
Card and PIN Code Mode
Card Mode
Fire Unlock Mode
Fire Lock Mode
Door <name> is on the Release Mode.
See Step 4 in 4.2.2 Step 2: Configuring the Doors.
Door <name> is on the Card or Common Mode.
See Step 4 in 4.2.2 Step 2: Configuring the Doors.
Door <name> is on the Card and PIN Code mode.
See Step 4 in 4.2.2 Step 2: Configuring the Doors.
Door <name> is on the Card mode.
See Step 4 in 4.2.2 Step 2: Configuring the Doors.
Door <name> is unlocked after Fire Inputs are
triggered.
See “Fire Action” at Step 2 in 4.2.2 Step 2:
Configuring the Doors.
Door <name> is locked after Fire Inputs are
triggered.
See “Fire Action” at Step 2 in 4.2.2 Step 2:
Configuring the Doors.
Force Unlock Remotely
Door <name> is unlocked remotely from the control
of GV-ASManager or GV-ASRemote server.
Force Lock Remotely
Door <name> is locked remotely from the control of
GV-ASManager or GV-ASRemote server.
Disable Remote Door Lock
Operation
The event of “Force Unlock Remotely” or “Force Lock
Remotely” is cleared.
Force Unlock Locally
Door <name> is unlocked on the site of Door
Controller.
Force Lock Locally
Door <name> is locked on the site of Door Controller.
Disable Local Door Lock
Operation
The event of “Force Unlock Locally” or “Force Lock
Locally” is cleared.
Reset
Door Controller <name> is reset.
214
Appendix
C.
E-Mail and SMS Alert Symbols
Icon
Description
%M (Message): include related alert message.
%T (Controller): include door controller’s name.
%D (Door): include triggered door’s name.
%L (Local Time): include local time.
%U (UTC): include UTC time.
%N (Card Number): include card number.
%H (User Name): include user name.
%G (Gender): include user’s gender.
%E (Employee ID): include employee ID.
%Y (Company): include company name.
%P (Department): include department name.
%F (Office): include office name.
%C (Photo): include user photo.
%S (Snapshot): include snapshot.
215
D.
Controller Status
Status
Description
Disconnected (Login Failed)
The username, password or crypto key (3DES)
entered is wrong.
Disconnected (Duplicate Connection)
Another GV-ASManager is connecting with the
controller.
Disconnected (Hardware Error)
The Controller ID entered is wrong. Or controller
errors occur.
216
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement