Manual
Subject to technical changes and to the availability
of the accessories supplied with the instruments.
CITIZEN SCALE (I) PVT. LTD.
Pawanoo. Tel. : 022 - 2860 7777 | Fax : 022 - 2860 7900 |Email: [email protected]|Web: www.citizenscales.com
CS-16-07-10/1
Analytical Balances
|
Carat Balances
|
Precision Balances
O p e r a t i n g
|
High Precision Industrial Balances
M a n u a l
Contents
1
1.1
1.2
1.3
Introduction ........................................................................................................
Warning & Safety Precautions ...........................................................................
Getting Started ...................................................................................................
Layout ..................................................................................................................
2
2.1
2.2
2.3
Setting up the Balance ...................................................................................... 9
Location .............................................................................................................. 12
Warm up .............................................................................................................. 14
Keys of Balance .................................................................................................. 15
3
Power On ............................................................................................................. 17
4
4.1
4.2
4.3
Simple Weighing .................................................................................................
External Calibration ............................................................................................
Internal Calibration ............................................................................................
Calibration Test .................................................................................................
5
5.1
Overview of Menu .............................................................................................. 32
Description of Menu .......................................................................................... 34
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
Functions ..............................................................................................................
Piece Counting ...................................................................................................
Percent Weighing (%) ........................................................................................
Custom Units ........................................................................................................
Animal Weighing.................................................................................................
Formulation..........................................................................................................
Check weighing .................................................................................................
Totalization...........................................................................................................
Density Determination .......................................................................................
1
34
44
49
57
61
65
69
73
77
7
7.1
7.2
7.3
7.4
Parameter Settings ............................................................................................
Time & Date Settings ..........................................................................................
ID / LID Settings .................................................................................................
Auto Calibration .................................................................................................
Windows Direct Communication .....................................................................
83
86
88
89
92
8
ISO / GLP - Compliant Printout ......................................................................... 95
9
9.1
9.2
9.3
Data Interface .....................................................................................................
Data Output Format .........................................................................................
Data Input Format .............................................................................................
Cabling Diagram ...............................................................................................
10
Error Codes .......................................................................................................... 102
11
Care & Maintenance ......................................................................................... 104
12
Dimensional Drawings ....................................................................................... 109
13
Specification ...................................................................................................... 113
14
Accessories ........................................................................................................ 122
2
3
4
5
6
19
23
25
27
97
98
100
101
1. Introduction
The models of the CX, CY, CT, CG and
SSH Series are weighing instruments of
special and high accuracy designed for
the measurement of mass, covering a
range from 0.01mg to 100 kg.
These weighing instruments speed up
your simple routine applications through
following features:
–
Extremely fast response times
CX, CY, CT, CG and SSH models meet
the highest requirements on the
accuracy and reliability of weighing
results through the following features:
–
Built-in applications
• Counting
• Percent weighing
• Animal weighing
• Formulation
• Totalization
• Custom Unit
• Check Weighing
• Density Determination
–
Total ease of operation
–
Direct Communication with MS Excel,
MS Word and other windows
application.
–
ISO/GLP-compliant recording
capability for printouts
–
Serial RS-232 port for optional
connection to a PC or Printer.
–
Filtering for unfavorable ambient
conditions, such as vibration, drafts,
etc.
–
Stable and repeatable weighing
results
–
Excellent readability under any
lighting conditions
–
Rugged, durable weighing system
Optional USB interface available on
request.
3
1.1 Warnings and Safety precautions
Warning when using pre-wired
RS-232 connecting cables: The pin
assignments in RS-232 cables
purchased from other manufacturers
may be incompatible with Citzien
balances. Be sure to check the pin
assignment against the chart on
page 101 before connecting
the cable.
To prevent damage to the equipment,
please read these operating instructions
carefully before using your balance.
Keep these instructions in a safe place.
Follow the instructions below to
ensure safe and trouble-free operation
of your balance.
-
The only way to switch the power off
completely is to disconnect the AC
adapter.
-
Connect only Citizen accessories
and options, as these are optimally
designed for use with your Citizen
balances.
–
Note on Installation:
The operator shall be responsible for
any modifications to Citizen
equipment andfor any connections
of cables or equipment not supplied
Do not use this balance/scale in a
hazardous area/location.
If you use electrical equipment in
installations and under ambient
conditions requiring higher safety
standards, you must comply with the
provisions as specified in the
applicable regulations for
installation in your country.
by Citizen and must check and, if
necessary, correct these
modifications and connections. On
request, Citizen will provide
information on the minimum
operating specifications
Make sure that the voltage rating
printed on the AC adapter is
identical to your local line voltage.
The balance has been constructed in
accordance with the European
Directives as well as international
regulations and standards for operation
of electrical equipment,
electromagnetic compatibility, and
stipulated safety requirements. Improper
use or handling,however, can result in
damage and/or injury.
4
–
Protect the DC adapter and the
weighing instrument from contact
with liquids.
When cleaning your balance,
make sure that no liquid enters the
balance housing; use only a slightly
moistened cloth to clean the
balance.
Do not open the balance/scale
housing. If the seal is broken, this will
result in forfeiture of all claims under
the manufacturer’s warranty. If you
have any problems with your
balance:
l
Contact your local Citizen office,
dealer or service center
1.2 Getting Started
Storage and Shipping Conditions
Do not expose the balance/scale to
extreme temperatures, blows, shocks,
vibration or moisture.
Unpacking the Equipment
After unpacking the balance/scale,
check it immediately for any visible
damage as a result of rough handling
during shipment
If you see any sign of damage:
Contact your local Citizen office,
dealer or service center
Accessories Supplied
The equipment supplied includes the
following :
–
–
–
–
–
–
–
-
Balance with display and control unit
Operating Manual
DC adapter
Gem bowl (CT scales only)
Pan Support (CX / CY / CT)
Weighing pan
Draft shield (CX / CY / CT)
Base Plat S.S. (CX / CY / CT)
Pan Cover (CX / CT)
1 Pair of Corner hole Cover
(CX / CY / CT)
Cautionary notes
Citizen balances may not be operated in
hazardous areas.
Before attachment of the DC adapter,
check whether the imprinted voltage
value matches the local supply voltage.
If it does not, contact your local CITIZEN
dealers.
CITIZEN balance may only be used
indoor in dry environment.
It is a good idea to save the box and all
parts of the packaging until you have
successfully installed your balance.
Only the original packaging provides
the best protection for shipment.
Before packing your balance, unplug all
connected cables to prevent damage.
5
1.3 Layout
CX / CY (0.1 mg) & CT
5
4
7
3
2
1
10
6 14 11
15
CY (1 mg)
4
9
12
8 13
CX / CY (0.1 mg) & CT
CY (1 mg)
1.
Keypad
1.
Keypad
2.
Display
2.
Display
3.
Model plate
3.
Model plate
4.
Weighing pan (90 Fmm)
4.
Weighing pan (128mm x 128mm)
5.
Draft shield (CX, CY & CT)
5.
Draft shield (CX, CY & CT)
6.
Leveling feet
6.
Leveling feet
7.
Pan Cover
8.
DC adapter socket
8.
DC adapter socket
9.
Provision for ant-itheft device
9.
Provision for anti-theft device
10.
Spirit Level
10.
Sprit Level
11.
RS232C interface
11.
RS232C interface
12.
Additional Display Sockets.
12.
Additional Display Sockets.
13.
Foot Tare Switch Socket.
13.
Foot Tare Switch Socket.
14.
14.
Calibration Switch (for Verified
Balance)
Calibration Switch ( for Verified
Balance)
Keys, operation and display are identical
for all CITIZEN balances.
15. Gem Bowl (CT)
Keys, operation and display are identical
for all CITIZEN balances.
6
CG
1.
Keypad
4
2.
Display
3
3.
Model plate
2
4.
Weighing pan (198 mmX 205 mm)
1
6.
Leveling feet
8.
DC adapter socket
9.
Provision for anti-theft device
10.
Spirit Level
11.
RS232C interface
12.
Additional Display Sockets.
13.
Foot Tare Switch Socket.
14.
Calibration Switch (for Verified
Balance)
CG
10
9
Keys, operation and display are identical
for all CITIZEN balances.
6 14 11
12
8 13
7
SSH
1.
Keypad
2.
Display
3.
Model plate
4.
Weighing pan (400mm x 300mm)
3
6.
Leveling feet
2
1
8.
DC adapter socket
9.
Provision for anti-theft device
10.
Spirit Level
11.
RS232C interface
12.
Additional Display Sockets.
13.
Foot Tare Switch Socket.
14.
Calibration Switch (for Verified
Balance)
4
10
Keys, operation and display are identical
for all CITIZEN balances.
6
11 12 8
8
2. Setting Up the balance
Balance with Analytical Draft-Shield Chamber
• Position the Draft shield carefully on the balance.
Step 1: Open your New balance and draft shield you will see lock mounted on balance body and
lock plate mounted below draft shield .
Step 2: Put your draft shield in same place and direction guided through RED color lines marked on
this sticker, with gentle hand push & rotate draft shield clock wise as shown in figure.
: While keeping draft shield on balance ensure you do not damage weight loading point.
Note : Ensure there must not be any gap between balance and draft shield, if incase there is gap
repeat again above procedure.
Step 3: Push fix both corner hole cover on bottom body of draft shield as shown in figure.
Corner
Hole Cover
Lock Plate
Weight
Loading
Point
Lock
9
• Place the components listed below inside the chamber in the order given:
(For CX / CY (0.1mg) / CT Series Balances)
- Corner Cover
– Base plate
- Pan Cover
– Weighing pan
• Place the components listed below inside the chamber in the order given:
(For CY (1mg) Series Balances)
- Corner Cover
– Base plate
– Pan Support
– Weighing pan
10
• Place the components listed below inside the chamber in the order given:
(For CG Series Balance)
- Bush
– Weighing pan
• Balances with a Rectangular Weighing Pan and a Weighing Capacity over 10 kg
- Place the weighing pan on the balance/scale
Under Weighing
A port for a under weighing hanger is located on the bottom of the balance.
• Remove the under weighing cover from the bottom of the balance (as shown
alongside)
• Suspend the below-balance weighing hook supplied from the hanger
• If necessary, install a shield for protection against drafts
11
2.1 Location
The optimum location
The correct location makes an important contribution to the accuracy of the weighing
results of high-resolution analytical and precision balances.
Hence, ensure a
• Stable, vibration-free position as horizontal as possible.
Avoid
• Direct sunlight
• Excessive temperature fluctuations,
• Drafts (Power ----- Air Conditioning System, Fans can also cause drafts)
The best position is an a stable bench in a corner protected against drafts as far
possible from doors, windows, radiators or the ventilation slots of air conditioners.
Anti-theft device
Citizen Balance are equipped with a lug for optional anti-theft device.
The anti-theft device (cable wit lock) is suitable for all models. It is available from
CITIZEN under order number CAD01.
12
Leveling the Balance
Citizen balances have a level control and adjustable leveling feet to compensate
for slight irregularities in the weighing bench surface. The balance is exactly
horizontal when the air bubble is in middle.
Leveling Balances with a Weighing Capacity up to 10 kg
Turn the two leveling feet as desire picture in diagram so that air bubble comes in
middle.
Air bubble at
“12 o’clock”
Turn both leveling feet counter- clockwise.
Air bubble at
“3 o’clock”
Turn left leveling foot clockwise,
right leveling foot counterclockwise
Air bubble at
“6 o’clock”
Turn both leveling feet clockwise
Air bubble at
“9 o’clock”
Turn left leveling foot clockwise,
right leveling foot counterclockwise
Leveling Balances with a Weighing Capacity over 10 kg
• Adjust the leveling feet until the air bubble is centered within the circle of the
level indicator
Note : The balance must be re-leveled each time it is moved to a new location.
13
2.2 Warm Up
Connecting Electronic Peripheral Devices
Make absolutely sure to unplug the balance from DC power before you connect or
disconnect a peripheral device (printer or PC)to or from the interface port.
Warmup Time
To deliver exact results, balance must warm up to operating temperature for as leasted
below before the first weighing operation is carried out.
• CX / CY (0.1mg) / CT all Analytical models: at least 60 minutes
• CY (1mg) / CG / SSH all Precision models: at least 30 minutes
Using Verified Balances as Legal Measuring Instruments in the EU* balance must warm
up for at least 24 hours after initial connection to DC power.
14
2.3 Keys of Balance
9
7
11
8
18
2
2
10
17
1
6
3
5
12
16
13
15
4
14
15
1
2
3
4
5
6
7
8
9
On/Off key: Switches the display
on / off
Tare key: Press here to tare the
weight of any container so that the
readout shows the net weight of
samples, also used to store
reference settings.
Cancel Function : Delete (Clear
Function) This key is generally used
to interrupt/cancel functions; for
example: – to end an application
program
– to interrupt calibration/
adjustment routines
Toggle Key : Press here to change
the Unit, Also used to increment
digit.
Cal Menu Function : Press here to
start calibration/ adjustment or to
enter user menu, Also use to shift
flashing digit from left to right.
Print Key : Press this key to send
displayed values over the built-in
data interface to a DataPrint
printer or a PC.
Weight Units
Weight readout in the selected
weight unit
Capacity Bar : This indicates the
total amount of weight on the Pan
10
11
12
13
14
15
16
17
18
Stability Symbol : This symbol is
displayed when the weight place
on the pan achieve stability
Asterik Symbol : This Symbol is
displayed when the display is
locked
Stability Filer : This symbol indicates
the chosen stability filter
Symbol indicating that the Auto /
Manual calibration/adjustment
function is active
Symbol indicating the active
program
Battery Level Indicator : This symbol
is indicates the Current charge of
the battery
Symbol indicating that a printout is
being generated
Symbol indicating that a GLP
compliant printout is being
generated
Seven segment readout indicating
the active program
16
b
3. Power ON
Connect DC Adaptor and Power ON the balance.
– It will display version number for software
– It will display numeric countdown
– It will display 8888888
– The system initialization process will begin with the display indicating the current
progress. (INIT 1% to INIT 100%)
– After the initialization is complete (100%) It will enter stand by mode &
display clock.
Stand by Mode
– After Power ON and initial test balance will automatically come in stand by mode.
– Press ON / OFF key to come to basic weighing
– Press ON / OFF key in basic weighing to come back to Stand by Mode
17
Key Functionality in simple weighing mode
Short-form operating Instructions
Press key briefly
Press and hold key until
desired display appears
Automatic procedure
Citizen balances have several control levels the following section
explains key functionality in simple weighing mode.
Weighing mode (operation)
Press briefly
Press & Hold
Switch on & off
Switch References
Change Weighing Unit
Calibrate (adjust)
CAL /
Menu key
Call Menu
Toggling key
Print Weighing Results
Tare
Cancel / Footer
Tare key
On / Off key
Print key
Confirm Setting
Abort / Cancel and Footer
when GLP is ON
18
Confirm Reference Setting
4. Simple Weighing
Purpose
The basic weighing function is always
accessible and can be used alone or in
combination with an application
program (counting, weighing in percent,
etc.).
Working with XXXXXXXX Models:
p
Features
– Taring the balance you can tare the
balance within the entire weighing
range.
– Assigning IDs to weights (as needed)
– Printing weights
19
Simple Weighing
4.0.1 Simple weighing
ð
Place weighing sample on the weighing pan.
ð
Wait until the stability symbol appears
ð
Read the result.
ð
Bar Graph will glow according to weight kept ON the PAN.
Tarring
4.0.2 Tarring
ð
Place empty container on the balance.
ð
The weight is displayed.
ð
Press <Tare> key briefly, the balance displays zero
ð
Add weighing sample to container, the net weight is displayed.
If the container is removed from the balance, the tare weight will be shown as a
negative value.
20
In case if stability is not achieved & user presses <TARE> key, display will shows
“---------------” until stability is achieved.
Display then shows “0.00 gm”
Switching of Weight Units
4.0.3 Switching of weight units
All Citizen balances can display weight values in different weight units.
The factory setting is Unit 1 (gm), Unit 2 (ct), Unit 3 (gm)
Switching between unit 1, unit 2 and unit 3
ð
Press <TOGGLE> key the display switches to the 2nd weight unit.
ð
Press <TOGGLE> key again, the display switches to the 3rd weight unit. OR
Application unit (If same is selected in menu)
Note
With certified balances the unit selection can be blocked following installation if
required by national legislation.
21
4.0.4 Simple weighing Pint out
When GLP ON
When GLP OFF
Print out generated when
Unit Toggling is done between
Unit1 (g), Unit2 (ct), Unit3 (Oz)
in Simple Weighing.
Print out generated when
Unit Toggling is done between
Unit1 (g), Unit2 (ct), Unit3 (Oz)
in Simple Weighing.
-----------------------20-Jul-10
10:35AM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
-----------------------LID:
1111111
+
49.9999 g
+
249.9990 ct
+
1.763690 oz
+
49.9998 g
+
249.9990 ct
+
1.763690 oz
+
49.9999 g
-----------------------20-Jul-10
10:36AM
Name:
................
------------------------
+
+
+
+
+
+
+
49.9999
249.9990
1.763690
49.9998
249.9990
1.763690
49.9999
g
ct
oz
g
ct
oz
g
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
22
4.1 External Calibration (adjusting)
To obtain weighing results, the balance must be matched to the acceleration due to
gravity at its location.
Calibration
Calibration is necessary
ð
Before the balance is used for the first time.
ð
At regular intervals during weighing operation.
ð
After a change in location.
Procedure
To obtain accurate results, the balance must be connected to the power supply and
allowed to warm up to the operating temperature as described on Page No 14
Ensure that the weighing pan is unloaded and close the doors of the draft shield (if
used). Balance should be Zero before calibration.
ð
Have required calibration weight ready
ð
Press and hold <CAL> key, display, shows
“CAL Et”
ð
Release <CAL> key now.
ð
The required calibration weight value will be displayed.
ð
Place calibration weight in center of pan.
The calibration (adjustment) is finished when “CAL donE” message is displayed.
The balance is again in the weighing mode and ready for operation.
Note : With certified balances, the calibration can be disabled after installation if
required by the national certification regulations.
The adjustment can be terminated at any time using the <CANCEL> key.
The following message appears : ‘Abort’
23
Calibration Report
If Balance is connected externally to PC or Data Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated
after the completion of Calibration process.
Unsuccessful Calibration
When GLP ON
Successful Calibration
When GLP ON
-----------------------------14-Jul-10
03:46PM
Citizen
Model
CX
220
Ser.no.
9930508
Ver.no.
R0.1.04
ID
1234567
-----------------------------Calibration:
External
-----------------------------14-Jul-10
03:46PM
Citizen
Model
CX220
Ser.no.
9930508
Ver.no.
R0.1.04
ID
1234567
-----------------------------Calibration:
External
W-ID
..................
Temperature
32.898'C
Set
+
20.00g
W-ID
..................
Temperature
32.898'C
Set
+
20.00g
Diff.
0.00g
External Cal Done
External Cal Failed
-----------------------------14-Jul-09
03:46PM
Name:
................
------------------------------
Diff.
0.00g
-----------------------------14-Jul-09
03:46PM
Name:
................
------------------------------
When GLP OFF
When GLP OFF
Calibration
:
W-ID
Temperature
Set
Diff.
External Cal Done
Diff.
External
Calibration
............
+
W-ID
32.905'C
20.00g
-0.01g
Temperature
Set
:
External
............
+
External Cal Failed
0.00g
24
32.905'C
20.00g
Internal Calibration
4.2 Internal Calibration
To obtain weighing results, the balance must be matched to the acceleration due to
gravity at its location.
Calibration is necessary
ð
Before the balance is used for the first time.
ð
At regular intervals during weighing operation.
ð
After a change in location.
Procedure
To obtain accurate results, the balance must be connected to the power supply and
allowed to warm up to the operating temperature as described on Page No 14
Ensure that the weighing pan is unloaded and close the doors of the draft shield (if
used). Balance should be Zero before calibration.
ð
Press and hold <CAL> key, display, shows
“CAL Int”
ð
Release <CAL> key now.
Internal Calibration process Starts.....
- When the Internal Weight is being loaded “C” will be displayed on display.
- When the Internal Weight is being unloaded “CC” will be displayed on display.
Calibration is finished when ‘Int.done’ is message is displayed.
The adjustment can be terminated at any time using the <CANCEL> key.
The following message appears : ‘Abort’
25
Internal Calibration Report
If Balance is connected externally to PC or Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated after
the completion of Calibration process.
Successful Calibration
When GLP ON
Unsuccessful Calibration
When GLP ON
-----------------------20-Jul-10
10:32AM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
-----------------------Calibration:
Internal
-------------------------------20-Jul-10
10:34AM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
-----------------------Calibration:
Internal
Start:
Temperature
Diff.
Start:
Temperature
Manual
29.449'C
+ 0.0009g
Internal Cal Failed
-----------------------20-Jul-10
10:34AM
Name:
................
------------------------
Internal Cal Done
Diff.
0.0000g
-----------------------20-Jul-10
10:32AM
Name:
................
------------------------
When GLP OFF
Calibration:
Start:
Temperature
Diff.
Manual
29.495'C
When GLP OFF
Internal
Manual
29.449'C
+ 0.0009g
Calibration:
Internal
Start:
Temperature
Manual
29.495'C
Internal Cal Failed
Internal Cal Done
Diff.
0.0000g
26
4.3
Calibration Test
Calibration (adjusting)
Calibration test determines the difference between the actual weight and the measured weight
Calibration test can be turned ON or OFF from the user menu.
When ON, cal test would be performed on external or internal calibration whichever is selected in
User Menu.
Procedure
ð
Have required calibration weight ready
ð
Press and hold <CAL> key, display, shows “CAL Et”
ð
Release <CAL> key now.
ð
The required calibration weight is shown on the display.
ð
Place calibration weight in center of pan.
ð
After the cal Test procedure is completed the difference between the actual & the
measured weight will be displayed on display.
The adjustment can be terminated at any time using the <CANCEL> key.
The following message appears : ‘Abort’
27
Calibration Test Report
If Balance is connected externally to PC or Data Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated
after the completion of Calibration process.
When GLP ON
When GLP OFF
-------------------------------14-Jul-10
00:03AM
Citizen
Model
CX220
1111111
Ser.no.
r0.1.04.01
Ver.no.
860054081
ID
-------------------------------Calibration:
External
Calibration:
External
W-ID
..................
Temperature
30.710'C
+200.0000g
Set
+ 0.0047g
Diff.
Calibration Test Done
W-ID
..................
30.710'C
Temperature
+200.0000g
Set
+ 0.0047g
Diff.
Calibration Test Done
--------------------------------14-Jul-10
00:03AM
Name:
................
---------------------------------
28
4.4
Calibration Test with Actual Calibration
Calibration (adjusting)
To correct the weighing results, the TARE key need to be pressed when the difference
is display upon pressing the TARE key. Actual calibration is performed ‘CAL done’ is
displayed and the weighing results are corrected as shown alongside.
Procedure
ð
Have required calibration weight ready
ð
Press and hold <CAL> key, display, shows “CAL Et”
ð
Release <CAL> key now.
ð
The required calibration weight is shown on the display.
ð
Place calibration weight in center of pan.
ð
The difference between the actual & the measured weight will be displayed.
ð
Press the Tare key when the difference is displayed.
ð
Actual Calibration is perform and Cal done is displayed.
The adjustment can be terminated at any time using the <CANCEL> key.
The following message appears : ‘Abort’
29
Calibration Test Report
If Balance is connected externally to PC or Printer via Rs232 Cable, successful or unsuccessful calibration report will be automatically generated after
the completion of Calibration process.
When GLP ON
When GLP OFF
-----------------------------------14-Jul-10
03:46PM
Citizen
Model
CX220
Ser.no.
9930508
Ver.no.
R0.1.04
ID
1234567
-----------------------------------Calibration:
External
Calibration
:
External
W-ID
Temperature
Set
Diff.
External Cal Done
Diff.
W-ID
..................
Temperature
32.898'C
Set
+
200.0000g
Diff.
-0.1235g
External Cal Done
Diff.
0.0000g
-----------------------------------14-Jul-09
03:46PM
Name:
................
------------------------------------
30
............
+
32.905'C
200.0000g
-0.1235g
0.0000g
Key Functionality in User Menu
The following section explains key functionality in User Menu mode.
Menu (called up with
Press briefly
)
Press & Hold
On / Off
Change Sub Menu Setting
Increments the value of digit
Change Main menu options
Shifts the digit from left to right
CAL /
Menu key
Confirm Setting
Toggling key
Store and quit menu
Print User Menu
Cancel / Footer
Tare key
On / Off key
Print key
Quit User Menu
31
5. Overview of Menu
In this menu, you can select unit 1, 2, 3 or Application Program, adjust the stability filter, Calibration choice, Auto Zero Tracking, automatic
shutdown and print setting.
Weighing Mode
W. Application
F
Weighing Unit 1
e
F de
Unit 2
Unit 3
gm
2
mg
F
F
F
F Cs
Ff
Weighing Unit 3
m
Pcs
F
Auto
Unit 1
Weighing Unit 2
kg
2
mo
ct
2
tls(2)
lb
2
tlh(2)
OZ
2
b
tlt(2)
Ozt
2
mo
dwt
GN
2
tls(2)
Auto
Ff
FA
Auto
gm
m
ct
2
lb
3
2
OZ
3
2
Ozt
2
GN
gm
m
3 mg
Stb 2
1
3 kg
b
Calibration Menu
Calibration Test
CAL ET
CA .
4
3 mo
3 ct
Entry into menu : Press and hold <CAL> Key until “MENU” appears on the display.
Release key, the 1st menu options “F none”
3 tls(2)
3 lb
Select menu options Press <CAL> Key briefly. Press key repeatedly to view
the current balance settings Main Menu Option.
dwt
3 tlh(2)
3OZ
tlt(2)
3 tlt(2)
3 Ozt
Store settings Press and hold <TARE> Key until “StoreED” appears.
3 dwt
3GN
Abort Press <CANCEL> Key briefly, The balance returns to the weighing
mode without storing the changes.
2
Baud Rate
Azt
Parity
57600
P spac
19200
P
a
2
tlh(2)
Stop Bit
Print Menu
1
e
P
9600
2
P
O
3
Modify settings Press <Toggle> Key repeatedly until the desired setting appears.
Confirm settings Press <TARE> key breifly when desired setting appears.
F
Auto Zero Tracking
mg
b
%
FA
kg
Stability Filter
P
GLP
Auto Off
A.
P E E
A.
4800
32
Reset
A. OFF -
GP
2
Reset
10
A.
A.
5
1
ES
Operating Instruction
ð
Press & hold CAL Key until “Menu” appears on the display.
ð
Release the CAL Key
ð
Existing preselected function is displayed from among the above mentioned 4
functions. This existing function is displayed with the stability indicator ON
ð
Press Toggle Key to Toggle to the desired functions.
ð
Press Tare Key briefly, once the desired function is displayed.
Stability indicator will be ON for that particular function now.
ð
Then Press & hold TARE Key once again till “STORED” is 5displayed on the display.
ð
If more then one changes are to be made within the Menu, make all the desired
changed by pressing toggle key to toggle within the SUB-Menus & Pressing Tare
key briefly.
Stability indicator will be ON for those changed Submenu
Options Then finally, pressing & holding TARE key until “Stored”
is displayed, will store all the changes made within different
menu options.
Note : If user did not press & hold <TARE> key & “Stored” message appears on the
display then any change made by user will remain unchanged.
Above instructions are to be followed for all menu options except : “Reset”
33
Application Menu
5.2 Description of Menu
5.2.1 Special applications and functions
Your balance can do more than just weighing. Built-in applications and functions
expand its possibilities and facilitate your daily work. You will learn these applications
and functions in the following Sections.
Preselecting a function
In this menu option you can preselect a function which you will then have available in
the weighing mode (Unit 3) at a keystroke
The following functions are available.
Piece counting
Your balance counts the pieces you add to or remove from the weighing container.
Percent weighing
Your balance allows you to weigh in to a preset value or determines percentage
weight deviations
.
Custom Unit : Your Balance allows you to weigh in any customized unit.
Animal Weighing : Your Balance allows you to weigh moving animals. You have the
option of Auto and Manual Animal Weighing.
Checkweighing : Your balance allows you to check whether a sample corresponds to
a preset target or is within a specific tolerance range.
34
Formulation : Your Balance allow individual weighing values to be summed to a total.
Totalization : Your balance allows you to weigh, individual weighing in piece which can
be summed to a total.
Density Determination : Your balance allows you to determine density of solids. Purity of
gold can also be determined on the basis of density.
No function preselected
You have no function available in the weighing mode (factory setting).
Note :
Above function will replace preset unit 3 automatically.
35
5.2.2 Unit 1, 2, 3 - selecting
The following weight units can be selected. With certified balance the unit selection
can be blocked following installation if required by national legislation.
Unit
Conversion factor
gram
g
1
= 1000g
kilogram
kg
1 kg
= 453.59237g
pound
lb
1 lb
= 28.349523125g
ounce
oz
1 oz
troy ounce
ozt
1 ozt = 31.1034768g
grain
GN
1 GN = 0.06479891 g
pennyweight
dwt
1 dwt = 1.555173843g
= 0.2g
carat
ct
1 ct
Milligram
mg
1 mg = 0.001g
momme
mo
1 mo = 3.749999953 g
= 4.6083162
mesghal
m
1m
= 37,42900 g
Hong Kong tales
H tl
1 Htl
Singapore taels
S tl
1 S tl = 37.799366256g
= 37.499995313g
Taiwan tales
t tl
1 t tl
= 15.1999998438g
baht
b
1b
36
5.2.3 Adjusting the stability Filter
You can use the stability Filter to match the balance to the ambient conditions.
2 Setting with normal balance surroundings (factory setting)
3 Setting with unstable balance surroundings. The balance operates slower
but is less sensitive to external influences (vibrations, etc.)
4 Setting with extreme unstable balance surroundings. The balance operates even
slower but is less sensitive to external influences (vibrations, etc.)
1 Setting with very stable balance surroundings. The balance operates very quickly
but is sensitive to external influences (vibrations, etc.)
5.2.4 Selecting Calibration Option
User can select any of the Two option for Calibration.
CAL ET
If the user select this option then the machine will perform External Calibration
when the CAL key is press & hold to display “CAL Et” & at this moment if user
release the key, user can enter into the External calibration.
CAL oFF When user press & hold CAL key, directly “Menu” appears on the display
without CAL Et option. Thus user cannot enter into the calibration process.
CAL INT If the user select this option then the machine will perform External Calibration
when the CAL key is press & hold to display “CAL Int” & at this moment if user
release the key, user can enter into the Internal calibration.
37
5.2.5 Calibration Test
User Can select any Two calibration test option.
CAL T ON If the user select this option then the machine will perform Calibration Test
when the CAL key is press & hold Calibration Test will perform on Internal
or External which ever is selected in calibration menu.
CAL T OFF Actual Calibration will be performed When the CAL key is press & hold .
5.2.6 Auto Zero Tracking
In this option, user can select whether to enable or disable Auto Zero Tracking
(Factory setting is ON)
The auto zero tracking continuously corrects any deviation from the zero pt; which can
be caused due to sight contamination on the weighing pan, for example.
38
Print Menu
5.2.7 Setting baud rate (data transmission rate)
The data transmission rate (baud rate) determines the speed of the transmission via the
serial interface.
The unit is baud (1 baud (bd) = 1 bit/second).
The following setting are available. bd 300, bd 600, bd 1200, bd 2400, bd 4800, bd 9600
(default), bd 19200, bd 57600
5.2.8 Setting Parity
This feature determine, the parity of the transmitted data. The following settings are
available. Parity None (default), odd, even, mark, space.
5.2.9 Stop Bit Selection
This setting allows the user to select the stop bit for the transmitted data.
The following settings are available stop bit 1 (Default) and stop bit 2.
39
5.2.10
Selecting data transfer mode
In this menu block you tell the balance how a value should be transferred to a
peripheral device (e.g. computer).
Prn. req
The next possible stable value will be transferred after triggering of the
Print key.
Prn. Con
All Values will be continuously transferred regardless of stability.
Prn. oFF
Data Transfer mode switched off
Prn. Aut
Next Possible stable value will be transfer automatically when the display
weight changes by + 1d.
Prn A.Ld
Next possible stable value will be transferred automatically when the
display weight changes by +/- 10d
5.2.11
GLP Menu Setting
GLP oFF
If the user select this option then the balance
print format are not compliance to ISO/GLP/GMP.
GLP on
If the user select this option then the balance
print format are compliance to ISO/GLP/GMP.
Note
If user selected GLP ON do ensure that user print footer for entering into next
transaction and enter into user Menu or Calibration.
40
5.2.12 GLP Menu Setting
GLP oFF
If the user select this option then the balance
print format are not compliance to ISO/GLP/GMP.
GLP on
If the user select this option then the balance
print format are compliance to ISO/GLP/GMP.
Note
If user selected GLP ON do ensure that user print footer for entering into next
transaction and enter into user Menu or Calibration.
5.2.13
A. Off - Setting automatic standby
The automatic shutdown appreciably extends the operating life of your Battery (If
Install) (Optional)
The balance will enter stand by mode. it A-oFF is activated
the display on the balance remains zero for a specific time as selected in the A.oFF
menu.
A. Off A. OFF 1
A. OFF 5
A. oFF 10
no automatic standby (factory setting)
automatic standby after 1 minutes
automatic standby after 5 minutes
automatic standby after 10 minutes
41
5.2.14 Reset of the balance setting
Reset balance setting and functions to factory setting (rESEt)
ð
Select “rESEt” and Press <TOGGLE> key breifly, display show “YES”
ð
Press <TARE> key breifly, display show “stored”
The balance is now reset to the factory setting and returns to the weighing mode._
Factory Setting
F none
Unit 1
Unit 2
Unit 3
Stb 2
CAL Et
CAL t
Azt ON
bd9600
Pr None
Stpbt 1
Print
GLP
A. oFF
No Function
gm
ct
gm
balance environment set to Normal
CAL External
CAL TEST OFF
Auto Zero Tracking set ON
Transmission rate
Parity set to none
Stop bit one
Req
OFF
- no automatic shutdown
42
USER MENU PRINT OUT
Press the Print Key in the user Menu to Print the current status of user menu.
When GLP ON
When GLP OFF
-----------------------------------14-Jul-10
03:46PM
Citizen
Model
Cy 220
Ser.no.
9930508
Ver.no.
R0.1.04
ID
1234567
-----------------------------------App
:
F Per
Unit1
:
g
Unit2
:
ct
Unit3
:
g
Stb
:
2
Cal
:
Ext
Cal test
:
Off
Azt
:
On
Baudrate
:
9600
Parity
:
None
Stop bit
:
1
Print
: Request
GLP
:
On
Auto Off
:
Off
-----------------------------------14-Jul-10
03:46PM
Name:
................
------------------------------------
App
Unit1
Unit2
Unit3
Stb
Cal
Cal test
Azt
Baudrate
Parity
Stop bit
Print
GLP
Auto Off
:
F Per
:
g
:
ct
:
g
:
2
:
Ext
:
Off
:
On
:
9600
:
None
:
1
: Request
:
On
:
Off
43
6. Functions
6.1 Piece counting
Procedure
Piece counting presupposes that you have preselected the “F count” function in the
menu
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “PCS” appears on the display.
Your balance now needs the weight of a reference number.
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference
pieces.
ð
Your balance suggests the last set reference no. as the reference number.
You can accept this suggestion or select one of the other reference numbers
available (5, 10, 20,50, 100 pieces, Free, wref, Update) by briefly pressing the
<TOGGLE> key.
Note : We recommend you to choose a reference number as high as possible as the
balance determines the average weight per piece and stores it as the reference
weight. As it is seldom the case that all pieces weigh exactly the same, the larger the
reference number selected, the greater the accuracy of the reference weight. This
application assumes uniform weight of each piece.
ð
When you have placed exactly the same number of pieces on the weighing pan as
selected reference pieces press TARE key.
As soon as the weighing result is stable, the calculated average piece weight is
accepted as the reference.
ð
After your balance has determined the piece weight, it displays the pieces as per
selected number and is now ready for piece counting.
You can use the <TOGGLE> key at any time to switch the display between the
piece number display, weighing unit 1 and weighing unit 2.
Note : The current set weight remains stored until it has been redetermined.
44
6.1.1 FREE (Reference settings)
The FREE option allows the user to set any reference other than the fixed available
reference.
(Default value is 001 and maximum possible value is 999)
Procedure
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “pcs” appears on the display.
Your balance now needs the weight of a reference number.
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference
pieces.
ð
Your balance suggests the last set reference no. as the reference number.
ð
Press the <TOGGLE> key until FREE is displayed.
ð
Press the <TARE> key to enter FREE reference settings.
ð
Last stored FREE value first digit flashing. Flashing digit indicates that digit value or
place can be changed.
ð
Press <TOGGLE> key ( ) to change the value of the Flashing digit.
ð
Press <CAL> key ( )to shift the flashing digit from Left to Right
ð
When you have placed exactly the same number of pieces on the weighing pan
as set in the FREE setting, press TARE key.
As soon as the weighing result is stable, the calculated average piece weight is
accepted as the reference
Now further weighing in PCS will be with respect to the reference calculation based upon
the FREE setting.
45
wRef Settings
6.1.2 wRef settings
If the piece weight is known, it can be entered directly. To do this, press the TARE key
when the system displays wRef in the reference menu. An input field appears, in which
the piece weight can be entered.
Since the balance does not have to determine a reference by weighing, the result of
the piece counting (the number of pieces currently on the weighing pan) is displayed
right after the piece weight has been confirmed.
Procedure
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “pcs” appears on the display.
Your balance now needs the weight of a reference number.
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference
pieces.
ð
Your balance suggests the last set reference no. as the reference number.
ð
Press the <TOGGLE> key until wRef is displayed.
ð
Press the <TARE> key to enter wRef reference settings.
ð
Last stored wRef value first digit flashing. Flashing digit indicates that digit value or
place can be changed.
ð
Press <TOGGLE> key ( ) to change the value of the Flashing digit.
ð
Press <CAL> key (
) to shift the flashing digit from Left to Right
ð
Press tge <TARE> key to store the wRef value.
Now further weighing in PCS will be with respect to the wRef value.
46
Updating Settings
6.1.3 Updating Settings
The Update feature improves the precision of piece counting results.
The average piece weight (reference) is recalculated with each reference
optimization. Because the new pieces that have been placed in the weighing pan
increase the basis for the calculation, the references, and therefore the result of the
piece count, are more exact.
Select the UPDATE feature from the reference menu. The reference can be updated
by pressing the CAL key which is confirmed by the displaying 'UPDATED' on the display.
Note
• The number of pieces placed in the weighing pan is larger than the reference piece
number shown on the display.
• The number of pieces placed in the weighing pan is not greater than twice the most
recently saved reference piece number (e.g. If the display shows 100 pcs the
added pieces should not be greater than 200).
• Update feature cannot be selected if the previous selected reference was 'wRef'
47
If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the reference menu of Piece Counting
function & make changes in the reference setting, automatically printout is generated on the Peripheral attached.
In the printout, reference number “nRef” and reference weight “wRef” is printed. After this user can Press Print Key to Print the reading on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
Printouts generated when Unit Toggling is done
between Application Unit (Pcs), Unit1 and
Unit2 and Reference Weight is changed
-----------------------------------29-Jul-09
03:46PM
Citizen
Model
CX 220
Ser.no.
9930508
Ver.no.
r0.1.04
ID
1234567
-----------------------------------LID:
1000000
NRef
5 pcs
WRef
4.00 g
Qnt +
5 pcs
NRef
50 pcs
WRef
0.40 g
Qnt +
50 pcs
Qnt +
25 pcs
NRef
5 pcs
WRef
2.00 g
Qnt +
5 pcs
-----------------------------------29-Jul-09
03:47PM
Name:
................
------------------------------------
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (Pcs), Unit1 and
Unit2 and Reference Weight is changed
nRef
wRef
Qnt +
Qnt +
nRef
wRef
Qnt +
Qnt +
nRef
wRef
Qnt +
Qnt +
5 pcs
2.00 g
5 pcs
10 pcs
10 pcs
2.00 g
10 pcs
5 pcs
50 pcs
0.20 g
50 pcs
100 pcs
Printout: Counting
nRef
+
10
:
wRef
+
21.14 g :
Qnt
+
500 pcs :
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
48
Reference sample quantity
Reference weight
i.e. weight of one piece
Calculated quantity
6.2 Percent Weighing (%)
The “Percent weighing” function enables you to weigh in to a preset value (1, 10,
20,50, 100%, Free, 100r, 100L, AtroM, AtroD) and to determine deviations from this
target value.
Percent Weighing (%) presupposes that you have preselected the “F per” function in
the menu
Procedure
ð
Place the empty container on the pan.
ð
Press the <TARE> key to tare the balance.
ð
Press the <TOGGLE> key briefly until “PER (%)” appears on the display.
Your balance now needs the weight of a reference percent (%).
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference
PER (%).
ð
Your balance suggests the last set reference % as the reference percent (%)
You can accept this suggestion or select one of the other reference percent (%)
available (1,10, 20, 50, 100 %, Free, 100r, 100L, AtroM, AtroD) by briefly pressing the
<TOGGLE> key. Default 1%
The FREE option allows the user to set any reference other than the standard available
reference.(Default value is 01.00 % and maximum possible value is 99.99%)
ð
Now place reference sample on the pan.
ð
Then press <TARE> key. Until dashes are displayed, your balance is
calculating the reference
ð
After your balance has determined the reference weight, it is ready for Percent
Weighing.
You can use the <TOGGLE> key at any time to switch the display between the Percent
(%) display, weighing unit 1 and weighing unit 2.
Note : The current set weight remains stored until it has been redetermined.
6.2.1 FREE (Reference settings)
The FREE option allows the user to set any reference other than the standard available
reference.
(Default value is 1.00% and maximum possible value is 99.99%)
Procedure
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “PER” appears on the display.
Your balance now needs the weight of a reference number.
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference
pieces.
ð
Your balance suggests the last set reference no. as the reference number.
ð
Press the <TOGGLE> key unit FREE is displayed.
ð
Press the <TARE> key to enter FREE reference settings.
ð
Last stored FREE value is displayed. Flashing digit indicates that digit value or
place can be changed.
ð
Press <TOGGLE> key ( ) to change the value of the Flashing digit.
ð
Press <CAL> key (
)to shift the flashing digit from Left to Right
ð
When you have placed exactly the same number of pieces on the weighing pan
as set in the FREE setting, press TARE key.
As soon as the weighing result is stable, the calculated average piece weight is accepted
as the reference
50
If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the reference menu of Percent
Weighing function & make changes in the reference setting, automatically printout is generated on the Peripheral attached.
In the printout, reference percent “pRef” and reference weight “wRef” is printed. After this user can Press Print Key to Print the reading on
the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (%), Unit1 and
Unit2 and Reference Weight is changed
-----------------------------------29-Jul-10
03:46PM
Citizen
Model
CX 220
Ser.no.
9930508
Ver.no.
R0.1.04
ID
1234567
-----------------------------------LID:
1000000
Ref
10.00 %
wRef
1.00 g
Pct +
10.00 %
+
10.0000 g
+
50.0000 ct
Pct +
20.00 %
pRef
1.00 %
wRef
20.00 g
Pct +
1.00 %
Pct +
0.50 %
-----------------------------------29-Jul-10
03:47PM
Name:
................
------------------------------------
Printouts generated when Unit Toggling is done
between Application Unit (%), Unit1 and
Unit2 and Reference Weight is changed
Ref
wRef
Pct +
+
+
Pct +
pRef
wRef
Pct +
Pct +
Printout: Counting
pRef
10%
:
wRef
+
21.14 g :
Pct
+
90.34% :
10.00 %
1.00 g
10.00 %
10.0000 g
50.0000 ct
20.00 %
1.00 %
20.00 g
1.00 %
0.50 %
Reference percentage
Reference weight
Calculated percentage
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
51
52
6.2.2 Differential Weighing
The Differential Weighing application is used to analyze changes in the weight of one
or more samples. The first step is to determine the initial weight of the sample (weighing
in). Selected components are then separated from or added to the sample. This
includes procedures such as drying, centrifugation, filtering, incineration, vaporization,
coating, etc. After the sample has been processed, it is re-weighed (residual weight).
The balance then determines the difference between the two weighed values.
100L% (Loss Content)
100L
100L (Loss)
The moisture content of the sample is displayed (and printed out) as a percentage of the
wet weight (= ww = initial weight = 100%). When the results are printed out, the moisture
content is designated 100L % " (Loss) (e.g. –11.35 100.00L%) and shown as a negative
value.
Dry weight DW – Wet weight WW
100L [0…-100%] = -------------------------------------------- *100%
Wet weight WW
100R% (Residual Content)
100R (Residue)
The dry content of the sample is displayed (and printed out) as a percentage of the wet
weight (= ww = initial weight = 100%). When the results are printed out, the dry content is
designated "100R%" (Residue) (e.g. 88.65 100.00R%).
100R
Dry weight DW
100R [100…0%] = -------------------------------------------- *100%
Wet weight WW
53
AtroM Moisture Content
The moisture content of the sample is displayed (and printed out) as a percentage of the
dry weight ( = DW = final weight = 100%). When the results are printed out, the ATRO
moisture content is designated “AtroM %" (ATRO Moisture Content) (e.g. –255.33 AtroM %)
and shown as a negative value.
%AtroM (Atro Moisture Content)
AtroM[%]
Dry weight DW – Wet weight WW
AtroM [0…-1000%] = -------------------------------------------- *100%
Dry weight DW
AtroD Dry Content (Wet weight)
%AtroD (Atro DryContent)
AtroD
[%]
The wet weight of the sample is displayed (and printed out) as a percentage of the dry
weight (= DW = final weight = 100%). When the results are printed out, the ATRO dry
content is designated “AtroD %" (ATRO Dry Content) (e.g. 312.56 AtroD %).
Wet weight WW
AtroD [100…1000%] = ----------------------------------------- *100%
Dry weight DW
54
100L% (Loss Content)
Percentage Weighing (%) (in 100R / 100L / AtroM / AtroD)
Percent Weighing (%) presupposes that you have preselected the “F per” function in
the menu
Procedure
ð
Press the <TARE> key to tare the balance.
ð
Press the <TOGGLE> key briefly until “PER (%)” appears on the display.
Your balance now needs the weight of a reference percent (%).
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference
PER (%).
ð
Your balance suggests the last set reference % as the reference percent (%)
Press the <TOGGLE> key until the following option is displayed (100R / 100L / AtroM
/ AtroD)
ð
Now place reference sample on the pan which is to be analyzed (Initial Weight).
ð
Then press <TARE> key. Until horizontal dashes are displayed, your balance is
calculating the reference.
ð
After your balance has determined the reference weight, it is ready for Percent
Weighing in Differential weighing.
ð
Now treat the sample which includes process like drying, centrifugation, filtering,
incineration, vaporization, coating, etc. After the sample has been processed, reweigh it (residual weight). The balance then determines the difference between
the two weighed values.
(Treat the sample& Re-Weigh it)
You can use the <TOGGLE> key at any time to switch the display between the Percent
(%) display, weighing unit 1 and weighing unit 2.
Note: If the current measured value on display mode is greater or less than the
predefined limit value (i.e. greater than 999.99 % or less than –999.99 %) the balance
displays Over range
(----Or----)
55
If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the reference menu of Percent
Weighing function & make changes in the reference setting, automatically printout is generated on the Peripheral attached.
In the printout, reference percent “pRef” and reference weight “wRef” is printed. After this user can Press Print Key to Print the reading on
the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
Printouts generated when Unit Toggling is done
between Application Unit (Per %), Unit1 and
Unit2 and Reference Weight is changed
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------LID:
1111111
pRef
ATROD %
wRef
0.5000 g
Pct +
100.00 %
Pct +
500.00 %
+
50.0000 g
+
250.0000 ct
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (Per %), Unit1 and
Unit2 and Reference Weight is changed
pRef
wRef
Pct +
Pct +
+
+
ATROD %
0.5000 g
100.00 %
500.00 %
50.0000 g
250.0000 ct
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
56
6.3 Custom Unit
The custom unit feature enables you to perform weighing in a customized unit i.e.
weighing can now be performed in a unit other than standard available 15 units.
Procedure
Custom unit presupposes that you have selected the 'F Cust' in the user menu.
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “CSt” appears on the display.
Your balance now needs conversion factor, accuracy and LSD to perform
weighing in custom unit.
ð
Press and hold the <TOGGLE> key to browse through the custom unit setting menu.
Your balance suggests the last stored values for the factor, accuracy and LSD.
ð
Press the <TARE> key to enter the specific setting.
Factor Setting
The factor value can be set to any user defined value except for zero.
ð
Press the <TARE> key to enter the factor setting.
ð
Press the <TOGGLE> key ( ) to change the value of the flashing digit.
ð
Press the <CAL> key ( ) to change the flashing digit from left to right.
ð
Press the <PRINT> key to shift the decimal position in a cyclic way.
ð
After proper setting of factor press the <TARE> key.
Note: Please refer error conditions for errors occurred in storing the Factor, Accuracy and
LSD settings.
57
Accuracy Setting
-
Press the <TARE> key when the Acc is displayed.
Press the <TOGGLE> key to browse through the standard available accuracy.
You can select any of the standard accuracy with the help of <TARE> key.
Standard accuracies available are
0.000001, 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000
The stability indicator alongside indicates the selected accuracy.
The Accuracy Setting is for display purposes and not for calculation of Custom unit.
LSD Setting
ð
Press the <TARE> key when LSD is displayed.
ð
Press the <TOGGLE> key to browse through the standard available LSD's.
ð
You can select any of the standard available LSD (Least significant Digit) with the
help of <TARE> key.
Standard LSD's available are
1, 2, 5, 10, 20, 50, 100
The stability indicator alongside indicates the selected LSD.
To store the Factor, Accuracy and LSD values, press and hold the <TARE> key when the
display shows Factor or Acc or LSD
The default settings are
Factor = 1.0000 (i.e. 1 gram)
Accuracy = 0.01
LSD = 1
58
E.g. If the settings are as follows,
Factor = 1.02356
Accuracy = 0.00
LSD = 50
Now if 50 gm of weight is loaded on the pan the calculation for displayed weight will be as follows,
Weight * Factor
= 50 * 1.023456
= 51.1728
The displayed weight will be 51.150
The second digit after decimal point will change in multiples of 5 because,
Accuracy * LSD
= 50 * 0.001
= 0.05
You can use the <TOGGLE> key at any time to switch the display between custom unit display, weighing unit 1 and weighing unit
2. User can go to Standby mode by pressing on/off key and go to Simple Weighing with unit 1 by Cancel key and balance shows
Current weights.
59
If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user enter into the Custom Unit Menu & make
changes in the Factor, Accuracy and LSD setting, automatically printout is generated on the Peripheral attached.
In the printout, the new Factor, Accuracy and LSD values are printed. After this user can Press Print Key to Print the reading on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
Printouts generated when Unit Toggling is done
between Application Unit (Cst), Unit1 and
Unit2.
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------LID:
1111111
Factor
3.023456
Accuracy
0.1
Lsd
2
+
151.2 cst
+
50.0000 g
+
250.000 ct
Factor
1.023456
Accuracy
0.001
Lsd
50
+
61.400 cst
+
51.200 cst
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (Cst), Unit1 and
Unit2.
Factor
Accuracy
Lsd
+
+
+
Factor
Accuracy
Lsd
+
+
3.023456
0.1
2
151.2 cst
50.0000 g
250.000 ct
1.023456
0.001
50
61.400 cst
51.200 cst
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
60
6.4 Animal Weighing
The animal weighing feature
enables you to perform weighing of
unstable samples (live animals). The
balance calculates the weight as
the average of a defined number of
individual weighing operations.
You can select from the two available
animal weighing modes i.e. Auto
animal weighing and manual animal
weighing.
Number of weighing operations for
calculation of an average mDef can
be set before the beginning of each
series.
Balance returns to the basic weighing
mode when unloaded; i.e., when the
load is below the unload threshold
The Unload threshold is 50 display
intervals.
The weighing unit for animal weighing
will be the same as selected for unit 1.
For Animal Weighing Process to start
two conditions should be satisfied,
the weight of the animal kept on the
pan should be higher than 100 display
increment i.e. if the balance
capacity is 300 gm and accuracy is
0.0001 gm, then in Animal Weighing
Process the weight of the animal
should be above 100 * 0.0001 g =
0.001g and When two successive
weight measured are within
predefined tolerance range.
61
6.4.1 Manual Animal Weighing
Manual Animal Weighing presupposes that you have selected the 'F Anl' in the user menu.
Procedure
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “
”symbol appears on the display.
Your balance now needs to set the countdown value.
ð
Press and hold the <TOGGLE> key to enter countdown options. The entire menu can
be accessed by pressing the <TOGGLE> key.
The stability symbol indicates the currently selected countdown value.
ð
Press the <TARE> key to select specific countdown value.
ð
Keep the animal on the pan, press the <CAL> key to start the animal weighing process
when both the condition required for animal weighing are met the countdown
process will start, when the countdown time ends the average weight on animal is
displayed with the display locked with flashing animal symbol.
Locked display is indicated by the flashing animal and AUTO symbol.
The countdown options available are,
t-5
t-10 (Default)
t-20
t-50
t-100
You can use the <TOGGLE> key at any time to switch the display between animal
weighing, weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing
on/off key and go to Simple Weighing with unit 1 by Cancel key and balance shows
Current weights.
62
6.4.2 Auto Animal Weighing
Auto Animal Weighing presupposes that you have selected the 'F Anl AUTO' in the user
menu. Auto animal weighing proves to be beneficial when the balance is used
majority for animal weighing and less for simple weighing thus reducing the time
required for animal weighing.
Procedure
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “ ” and “AUTO” symbol appears on the
display.
Your balance now needs to set the countdown value.
ð
Press and hold the <TOGGLE> key to enter countdown menu. The entire menu can
be accessed by the <TOGGLE> key.
The stability symbol indicates the currently selected countdown value.
ð
Press the <TARE> key to select specific countdown value.
ð
Keep the animal on the pan, when both the condition required for animal weighing
are met the countdown process will start, when the countdown time ends the
average weight on animal is displayed with the display locked.
Thus there is no need of pressing a key to start the countdown process in the auto
animal weighing mode.
Locked display is indicated by the flashing animal and AUTO symbol.
The countdown options available are,
t-5
(Auto), t-10 (Auto) Default, t-20 (Auto), t-50 (Auto), t-100(Auto)
You can use the <TOGGLE> key at any time to switch the display between animal
weighing, weighing unit 1 and weighing unit 2. User can go to Standby mode by
pressing on/off key and go to Simple Weighing with unit 1 by Cancel key and balance
shows Current weights.
63
If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user enter into the Countdown Menu of Animal
Weighing & make changes in the countdown time automatically printout is generated on the Peripheral attached.
In the printout, the new countdown value ’mDef’ is printed. After this user can Press Print Key to Print the reading on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
Printouts generated when Unit Toggling is done
between Application Unit (Anl), Unit1 and
Unit2 and Reference Weight is changed
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------Cnt
20
xNt +
50.0709 g
+
50.0715 g
+
250.3575 ct
xNt +
50.0709 g
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (Anl), Unit1 and
Unit2 and Reference Weight is changed
Cnt
xNt +
+
+
xNt +
20
50.0709 g
50.0715 g
250.3575 ct
50.0709 g
Printout: Counting
Cnt
20
xNt
+
:
50.0709 g :
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
64
Number of subweighing
operations
Calculated Average
6.5 Formulation
Note:
- Individual weights an be added
into summation only if the weights are
greater than 20d, this is indicated by
“
” symbol.
The formulation feature allows
individual weighing values to be
summed to a total.
User can select from two available
formulation modes i.e. Manual
formulation and auto formulation.
- The weighing unit for formulation
will be the same as selected for unit 1.
Maximum no of weights that can be
summed is 99.
Store component weights with
• Display zeroed automatically after
value is stored, and
• Automatic printout (print
application parameters)
• Of the last component weight (net
value) and
• Of the total weight (tare value)
Clear component memory when
weighing series is canceled by
pressing CANCEL key
65
6.5.1 Manual Formulation
Manual formulation presupposes that you have selected the 'F Form' in the user menu.
Procedure
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until Fol is displayed on the display.
ð
Add weight on the pan. Weight can be added to summation when “
” is
displayed on the display i.e. when it is greater than 20d.
ð
Press the <CAL> key to store the weight, the balance displays “n-1” indicating that 1st
weight is stored. The weight is tarred automatically and simultaneously print
command is given.
E.g. if 9.9968 gm is added the printer output is as follows
N1
:
9.9968 g
Tot
:
+9.9968 g
Further addition of weights will give the following output (addition of 20.0070 gm).
N2
:
20.0070 g
Tot
:
+39.0038 g
ð
To view the total weight, press the <CAL> and <TOGGLE> key together. The print
command is given automatically
N
2
Tot
:
+ 39.0038 g
66
6.5.2 Auto Formulation
Auto formulation presupposes that you have selected the 'F Form AUTO' in the user
menu.
Auto formulation proves to be beneficial when the balance is used in majority for
formulation weighing and less for simple weighing thus reducing the time required for
formulation as compared to manual formulation.
ð
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until Fol and AUTO is displayed on the display.
ð
Add weight on the pan. Weight can be added to summation when “
” is
displayed on the display i.e. when it is greater than 20d.
ð
When the weight is stable the weight is stored in the formulation procedure and the
balance displays “n-1” indicating that 1st weight is stored. The weight is tarred
automatically and simultaneously print command is given. Thus there is no need to
press any to start the auto formulation procedure.
You can use the <TOGGLE> key at any time to switch the display between formulation,
weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing on/off key
and go to Simple Weighing with unit 1 by CANCEL key and balance shows Current
weights.
67
If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user adds weight to the formulation procedure
automatically printout is generated on the Peripheral attached.
In the printout, the component added ‘N x ’along with the total sum ‘Tot’ is printed. After this user can Press Print Key to Print the reading
on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
Printouts generated when Unit Toggling is done
between Application Unit (Forl), Unit1 and
Unit2 and Reference Weight is changed
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------N1 +
20.0000 g
Tot +
20.0000 g
+
20.0000 g
+
100.0000 ct
N2 +
50.0000 g
Tot +
70.0000 g
N
2
Tot +
70.0000 g
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (For), Unit1 and
Unit2 and Reference Weight is changed
N1 +
Tot +
+
+
N2 +
Tot +
N
Tot +
20.0000 g
20.0000 g
20.0000 g
100.0000 ct
50.0000 g
70.0000 g
2
70.0000 g
Printout Configuration
N1
+
20.0000 g
Tot
+
20.0000 g
N2
+
50.0000 g
Tot
+
70.0000 g
N
2
Tot
+
70.0000 g
1st component and its weight
Sum of components
2nd component and its weight
Sum of components
Total number of components
Total formulation weight
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
68
6.6 Check Weighing
This feature is used to check whether a sample corresponds to a preset target or is with a
specific tolerance range.
The results displayed can also be available on external port, which with the help of
electronic processing can be used to control additional devices.
The check weighing procedure will always be carried out in unit 'gm'.
Check weighing presupposes that you have selected the 'F CHw' in the user menu.
Procedure
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “CW” is displayed on the display.
Your balance now needs the target and tolerance values.
If entering the check weighing for the first time the target and tolerance setting menu will
be displayed.
69
Target and Tolerance Settings
ð
Press and hold the <TOGGLE> until the target and tolerance setting menu is
prompted.
ð
Press the <TOGGLE> key to browse through the TARGET, HI, and LOW setting.
ð
Press the <TARE> key to enter specific setting.
ð
Press the <TOGGLE> key ( ) to change the value of the flashing digit.
ð
Press the <CAL> key ( ) to change the flashing digit from left to right.
ð
After proper setting of values press the <TARE> key.
ð
Press and hold the <TARE> key to store the values of target and tolerance values.
Note: To view the weight when the balance displays LL or HH press the <CAL> key press
the <CAL> key again to display LL or HH.
70
Load the weight on the pan and the balance will display the results according to the
preset values of target and tolerance.
For Low Range
E.g. If the values are as follows,
TARGET = 150.0000 gm
HI
= 155.0000 gm
LOW
= 145.0000 gm
Now if 144.0000 gm is loaded on the pan the display shows LL indicating that the loaded
weight is less than the low value set.
If 156.0000 gm is loaded on the pan the display shows HH indicating that the loaded
weight is greater than the high value set.
While the balance displays LL or HH the buzzer will beep continuously to indicate that the
weight is out of the tolerance band and the corresponding lines on the external will be
enabled.
For High Range
If the weight is in the tolerance range the balance will display the weight similar to simple
weighing.
You can use the <TOGGLE> key at any time to switch the display between check
weighing, weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing
on/off key and go to Simple Weighing with unit 1 by CANCEL key and balance shows
Current weights.
71
If the balance is connected eternally to PC or Printer through RS 232 C then, whenever user enter into the Target and Tolerance Setting Menu of
Check Weighing Menu & make changes in the setting, automatically printout is generated on the Peripheral attached.
In the printout, Target and Tolerance value are printed. After this user can Press Print Key to Print the reading on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (Chw), Unit1 and
Unit2 and Reference Weight is changed
Printouts generated when Unit Toggling is done
between Application Unit (Chw), Unit1 and
Unit2 and Reference Weight is changed
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------Target
150.0000 g
Hi
160.0000 g
Lo
140.0000 g
-------LL------+
99.9979 g
+
149.9979 g
-------HH------+
200.0029 g
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
Target
Hi
Lo
150.0000
160.0000
140.0000
-------LL------+
99.9979
+
149.9979
-------HH------+
200.0029
g
g
g
g
g
g
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
72
6.7 Totalization
The totalization procedure allows individual weighing pieces to be summed to a total.
User can select from two available formulation modes i.e. Manual totalization and auto
totalization.
Maximum no of weights that can be summed is 99.
Store component pieces with
• Display zeroed automatically after value is stored, and
• Automatic printout (print application parameters)
• Of the last added pieces and
• Of the total number of pieces.
Clear component memory when weighing series is canceled by pressing CANCEL key
Note:
- Individual weights an be added into summation only if the added pieces is greater
than 2, this is indicated by “
” symbol.
6.7.1 Manual Totalization
Procedure
Manual totalization presupposes that you have selected the 'F tot' in the user menu.
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “tot” is displayed on the display.
Your balance now needs the weight of a reference number.
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference pieces.
73
ð
Your balance suggests the last set reference no. as the reference number.
You can accept this suggestion or select one of the other reference numbers available
(5, 10, 20, 50, 100 pieces) by briefly pressing the <TOGGLE> key.
ð
Now place the selected number of reference pieces on the pan.
ð
When you have placed exactly the same number of pieces on the weighing pan as
selected reference pieces press TARE key.
As soon as the weighing result is stable, the calculated average piece weight is
accepted as the reference.
ð
Add weight on the pan. Weight can be added to summation when “
” is displayed
on the display i.e. when number of pieces is greater than 2.
st
ð
Press the <CAL> key to store the weight, the balance displays “n-1” indicating that 1
weight is stored. The weight is tared automatically and simultaneously print command is
given.
E.g. if 20.0000 gm and the reference is selected as 5, the printer output is as follows
nRef
5 pcs
wRef
4g
N1 +
5 pcs
Tot +
5 pcs
Further addition of weights will give the following output (addition of 10.0000 gm).
N2 +
2 pcs
Tot +
7 pcs
ð
To view the total weight, press the CAL and NEXT key together. The print command is
given automatically
N
2
Tot +
7 pcs
74
6.7.2 Auto Totalization
Auto totalization presupposes that you have selected the 'F tot AUTO' in the user menu.
Auto totalization proves to be beneficial when the balance is used in majority for totalization
weighing and less for simple weighing thus reducing the time required for totalization as
compared to manual totalization
Procedure
Place the empty container on the pan.
ð
Press the <TARE> key briefly to tare the balance.
ð
Press the <TOGGLE> key briefly until “tot” and AUTO is displayed on the display.
Your balance now needs the weight of a reference number.
ð
Press and hold the <TOGGLE> key until you are prompted to load the reference pieces.
ð
Your balance suggests the last selected reference number.
You can accept this suggestion or select one of the other reference numbers available
(5, 10, 20, 50, 100 pieces) by briefly pressing the <TOGGLE> key.
ð
Now place the selected number of reference pieces on the pan.
ð
When you have placed exactly the same number of pieces on the weighing pan as
selected reference pieces press TARE key.
As soon as the weighing result is stable, the calculated average piece weight is accepted
as the reference.
ð
Add weight on the pan. Weight can be added to summation when “
” is
displayed on the display i.e. when number of pieces is greater than 2.
ð
When the weight is stable the number of pieces is stored in the totalization procedure
and the balance displays “n-1” indicating that 1st weight is stored. The weight is tarred
automatically and simultaneously print command is given. Thus there is no need to
press any to start the auto totalization procedure.
You can use the <TOGGLE> key at any time to switch the display between totalization,
weighing unit 1 and weighing unit 2. User can go to Standby mode by pressing on/off key
and go to Simple Weighing with unit 1 by CANCEL key and balance shows Current weights.
75
If the balance is connected externally to PC or Printer through RS 232 C then, whenever user
enter into the reference menu of Totalization function & make changes in the reference setting,
automatically printout is generated on the Peripheral attached.
In the printout, reference number “nRef” and reference weight “wRef” is printed. After this user
can Press Print Key to Print the reading on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of
those corresponding units.
When GLP ON
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (Tot), Unit1 and
Unit2 and Reference Weight is changed
Printouts generated when Unit Toggling is done
between Application Unit (Tot), Unit1 and
Unit2 and Reference Weight is changed
------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
------------------------------nRef
10 pcs
wRef
2.0000 g
N1 +
10 pcs
Tot +
10 pcs
N2 +
25 pcs
Tot +
35 pcs
N3 +
10 pcs
Tot +
45 pcs
N
3
Tot +
45 pcs
------------------------------28-Jul-10
03:23PM
Name:
................
-------------------------------
nRef
wRef
N1 +
Tot +
N2 +
Tot +
N3 +
Tot +
N
Tot +
10
2.0000
10
10
25
35
10
45
3
45
pcs
g
pcs
pcs
pcs
pcs
pcs
pcs
pcs
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer
has not been printed.
2) To print footer user will have to Press <CANCEL> key.
76
6.8 Density Determination
The density is determined applying the principle of Archimedes, which states that any body
immersed in a fluid becomes lighter by an amount equal to the weight of the fluid that it has
displaced.
Purity of gold can also be determined on the basis of density.
The weighing unit of density determination will be 'grams'.
Density determination presupposes that you have selected the 'F Den' in the user menu.
To calculate the density of sample, the balance should know the type of liquid and its
temperature, used to calculate the density of solid.
Procedure
Press and hold the <TOGGLE> until the functionality menu is prompted.
ð
Press the <TOGGLE> key to browse through the Temperature, Liquid and Mode
ð
settings.
Temperature Setting
Press the <TARE> key when the 'temp' is displayed.
ð
Press the <TOGGLE> key ( ) to change the value of the flashing digit.
ð
Press the <CAL> key ( ) to change the flashing digit from left to right.
ð
After proper setting of values press the <TARE> key.
ð
The default value of temperature is 25.0 C
ð
This setting is alterable only when the liquid selected is water or ethanol. If the liquid
ð
selected is 'Other' the temperature setting will ‘nA’ i.e. Not applicable.
77
Liquid Setting
You can select from the three available options i.e. water, ethanol and other.
ð
Press the <TOGGLE> key to change the liquid option.
ð
After proper selection of the liquid setting the <TARE> key.
The default option is distilled water.
Mode Setting
You can select from three options i.e. compensated, uncompensated and purity of gold.
ð
Press the <TOGGLE> key to change the Mode setting.
ð
After proper selection of mode press the <TARE> key .
The default option is compensated.
The results of purity of gold will be shown in carats.
78
Density Determination Procedure
Add Wt. in Air
Attach the Density determination Kit to the Balance
ð
Press the <TARE> key briefly to TARE the balance.
ð
Press the <TOGGLE> key briefly until “Den” appears on the display.
ð
Press the <CAL> key to start the density determination procedure. The Balance now asks
ð
for weight of the sample in air. (With Wt.Air flashing on the display every 10 seconds)
Place the sample on density determination kit, When the weight is stable press the CAL
ð
key to accept the weight of sample in air.
Now the balance asks for the weight of sample in liquid (With Wt.Liqd flashing on the
ð
display every 10 seconds)
Now immerse the sample in the liquid, When the weight is stable press the CAL key to
ð
accept the weight of sample in liquid.
The balance will show the results upon the selected mode i.e. compensated,
ð
uncompensated or gold.
Add Wt. in Liquid
79
Display for compensated density
Density Calculations
With compensation for air density
ñ =
compensated density
Display for uncompensated
A * (ñ0 - ñl)
+ ñl
(A - B)
ñ = density of sample
A = weight of sample in air
B = weight of sample in auxiliary liquid
ñ0 = density of auxiliary liquid
ñl = air density (0.0012 g/cm3)
e.g.
ñ = (A / (A - B)) (ñ0 - ñl) + ñl
= (20.000 / (20.000-18.935)) (0.99689 – 0.0012) + 0.0012
= 18.699 g/cm3
Without compensation for air density
ñ =
A
ñ0
(A - B) *
ñ = ñ0 (A / (A - B))
e.g.
ñ = ñ0 (A / (A - B))
= (20.000 / (20.000-18.935)) (0.99689)
= 18.721 g/cm3
80
If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the menu of Density function & make
changes in the, automatically printout is generated on the Peripheral attached.
In the printout, Temperature, Liquid and Mode are printed. After this user can Press Print Key to Print the reading on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
When GLP OFF
Printouts generated when Unit Toggling is done
between Application Unit (Den), Unit1 and
Unit2 and Reference Weight is changed
Printouts generated when Unit Toggling is done
between Application Unit (Den), Unit1 and
Unit2 and Reference Weight is changed
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------Mode
GOLD
Liquid
WATER
Temperature
25.0
Pur +
23.1 ct
+
18.9350 g
+
94.675 ct
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
Mode
Liquid
Temperature
Pur +
+
+
GOLD
WATER
25.0
23.1 ct
18.9350 g
94.675 ct
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
81
If the balance is connected externally to PC or Printer through RS 232 C then, whenever user enter into the menu of Density function & make
changes in the, automatically printout is generated on the Peripheral attached.
In the printout, Temperature, Liquid and Mode are printed. After this user can Press Print Key to Print the reading on the display.
Also user can Toggle to other unit through Toggle key & Press Print Key to get the print out of those corresponding units.
When GLP ON
Printouts generated when Unit Toggling is done
between Application Unit (Den with Compensated
Mode Liquid as Ethanol), Unit1 and Unit2 and
Reference Weight is changed
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------Mode
COMPENSATED
Liquid
ETHANOL
Temperature
28.0
Den +
0.6995g/c3
+
18.9350 g
+
94.675 ct
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
When GLP ON
Printouts generated when Unit Toggling is done
between Application Unit (Den with Uncompensated
Mode and Liquid as None), Unit1 and Unit2 and
Reference Weight is changed
----------------------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
----------------------------------Mode
UNCOMPENSATED
Liquid
NONE
Temperature
NONE
Den +
0.6994g/c3
+
18.9350 g
+
94.675 ct
----------------------------------28-Jul-10
03:23PM
Name:
................
-----------------------------------
Note : 1) User cannot enter into the external calibration or menu when GLP is ON & footer has not been printed.
2) To print footer user will have to Press <CANCEL> key.
82
Key Functionality in parameter
settings mode
7. Parameter Settings
The following section explains key functionality in parameter
settings mode.
Press briefly
Press & Hold
Change Sub Menu Setting
Increments the value of digit
Change Main menu options
Shifts the digit from left to right
Store and quit menu
(Auto Cal Menu)
Confirm Setting
To Change Time Format
(AM / PM / 24 hours) in
Time Settings
CAL /
Menu key
Quit the Current Parameter Menu
Toggling key
Cancel / Footer
Tare key
On / Off key
Print key
83
AUTOCAL SETTINGS
ID / LID SETTINGS
TIME DATE SETTINGS
ID
TIME
P CAL ON
LID
DATE
P CAL OFF
AUTOCAL OFF
AUTO CAL ON
84
TIME
TEMP.
0.50C
0.5 Hr
1 C
0
1 Hr
2 0C
3 Hr
5 0C
24 Hr
OFF
OFF
Parameter Settings
By accessing the parameter menus the user can change the following settings.
• ID and LID settings.
• Time and Date Settings.
ID & LID SETTINGS
• Auto Calibration and Power On Calibration Settings.
Operating Instructions
These menus can be accessed by pressing the PRINT key or CAL key when all the
characters of the display when coming out of stand by mode or Power On.
TIME & DATE SETTINGS
AUTO & POWER ON
CAL SETTINGS
85
7.1
Clock Menu
In this menu, User can set the Clock.
Clock setting consist of 2 settings. They are
TIME
In this submenu user can set the time in hours, minutes & seconds
AM, PM & 24 hrs.
DATE
In this submenu user can set the date, Month & Years
Operating Instructions
ð
Press the PRINT key for 2 sec when coming out from stand by
or Power on mode.
7.1.1
SET TIME
ð
Current Time is displayed with first digit flashing. Flashing digit indicates that digit
value or place can be changed.
ð
Press TOGGLE key ( ) to change the value of the Flashing digit.
ð
Press CAL key ( ) to shift the flashing digit from Left to Right
ð
After proper setting of time in hours, minutes & seconds respectively
for zeroes starting from left, press Tare key
ð
Press the PRINT key to Change the format AM, PM & 24hrs.
86
7.1.2
SET DATE
ð
Press TARE key, “date” is display
ð
Press TARE key, current date is displayed with first digit flashing. Flashing digit indicates
that digit value or place can be changed.
ð
Press TOGGLE key ( ) to change the value of the Flashing digit.
ð
Press CAL key ( ) to shift the flashing digit from Left to Right
ð
After proper setting of date in day, month & year respectively for zeroes starting from left,
ð
Press TARE key to set the date
87
7.2 ID / LID Setting
In this menu user can set the identification number & Lot Identification number.
Operating Instructions
ð
Press the PRINT key briefly when coming out from stand by or Power on mode.
7.2.1 SET ID
ð
Last stored ID is displayed with first digit flashing. Flashing digit indicates that digit
value or place can be changed.
ð
Press TOGGLE key ( ) to change the value of the Flashing digit.
ð
Press CAL key ( ) to shift the flashing digit from Left to Right
ð
Press the TARE key to store ID Value
7.2.2 SET LID
ð
Last stored LID is displayed with first digit flashing. Flashing digit indicates that digit
value or place can be changed.
ð
Press TOGGLE key ( ) to change the value of the Flashing digit.
ð
Press CAL key ( ) to shift the flashing digit from Left to Right
ð
Press the TARE key to store LID Value
88
7.3 Auto Calibration
ð
Auto Internal Calibration can be triggered automatically, by the following
• Time
• Temperature
• Power on Calibration
Operating Instruction
ð
Press the CAL key briefly when coming out from stand by or Power on mode.
7.3.1 Auto CAL Time Settings
Select Auto CAL ON and press the <TARE> key, now press the <TARE> key when the
Displays shows TIME to enter time settings.
User can set time value = 0.5 hrs.
User can set time value = 1 hrs.
User can set time value = 2 hrs.
User can set time value = 3 hrs.
User can set time value = 24 hrs.
User can set time value = OFF
Auto Cal triggered due to time will take place irrespective of cal test on or OFF
Note : The Above setting is available with balances with internal calibration.
89
7.3.2 Auto CAL Temperature Settings
Select Auto CAL ON and press the <TARE< key, now press the <TOGGLE> key when the
LCM displays TIME, press the <TARE> key to enter temperature settings.
User can set temp. value = 0.50C.
User can set temp. value = 10C.
User can set temp. value = 20C.
0
User can set temp. value = 5 C.
User can set temp. value = OFF
Auto Cal triggered due to temp. change will take place irrespective of CAL test is On
or oFF
Note : The Above setting is available with balances with internal calibration.
90
7.3.3 Power on Calibration
Press the CAL key when the LCM displays Auto CAL On or Off enter Power ON
calibration options.
This setting enables the user to turn on or turn off power on calibration.
Power on calibration will take place every time the balance is powered on.
Power on Cal will take place irrespective of whether CAL Test is On or Off.
Note : The Above setting is available with balances with internal calibration.
91
7.4 Windows Direct Communication
The windows direct communication
function enables you to send the data
from the balance directly to any
windows application program for e.g.
Microsoft word, excel etc.
ð
Click OK to accept the settings for
serial key.
ð
Click APPLY and then OK to save the
Accessibility options.
The printer settings in the user menu will
be applicable to the windows direct
communication also i.e. Data Transfer
Mode, Baud rate, Parity, Stop Bit and GLP
The settings attributed to windows direct
communication are
• Unit ON or OFF.
• Separator type ENTER or TAB.
To enable windows direct communication, make sure that you have
turned it on from the windows side as well.
ð
Enter control panel.
ð
Open ACCESSIBILITY OPTIONS from
control panel.
ð
In the general tab turn on serial key
option.
ð
Set the baud rate and COM port
from the settings option.
92
Windows direct communication settings (Balance Side)
ð
Press and hold the <PRINT> key in simple weighing mode until the windows print
menu is prompted.
ð
Press the <TOGGLE> key briefly to change the windows option to ON of OFF. The
default option is OFF.
Windows Unit settings
Select Windows print option as ON and press the <TARE> key, now press the <TARE> key
when the LCM displays UNIT to enter unit settings.
User can set Unit option as ON (Along with the numerical value the unit will also be sent
to windows).
User can set Unit option as OFF (Only the numerical value will be sent to windows and not
the unit).
93
Windows Separator settings
Select Windows print option as ON and press the <TARE> key, now press the <TARE> key
when the LCM displays 'Separat' to enter Separator settings.
User can set SEPERATOR option as ENTER (After every value printed on the windows side
an ENTER command is given so every subsequent data will print on new line, in Excel
every new data will be printed in new row).
User can set SEPERATOR option as TAB (After every value printed on the windows side a
TAB command is given so every subsequent data will printed with tab, in Excel every new
data will be printed in new column).
94
8. ISO/GLP-compliant Printout/Record
Features
You can have the parameters pertaining to the ambient weighing conditions printed before (GLP header) and
after (GLP footer) the values of a weighing series. These parameters include:
GLP header:
– Date
– Time at beginning of measurement
– Balance manufacturer
– Balance model
– Balance serial number
– Software version number
– Identification number of the current sampling operation
GLP footer:
– Date
– Time at end of measurement
– Field for operator signature
The record is output to a CITIZEN data printer or a computer.
Settings
Set print option to request & GLP ON
Function Keys
Press the Print key to output header and first measured value.
End an Application:
Output GLP Footer : Press Cancel Key
End an application program Press Cancel key
95
The ISO/GLP-compliant record can contain the following lines:
-----------------------28-Jul-10
03:19PM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
-----------------------LID:
1111111
nRef
170 pcs
wRef
0.2945 g
Qnt +
170 pcs
+
50.0650 g
+
250.3250 ct
-----------------------28-Jul-10
03:23PM
Name:
................
------------------------
Dotted line
Date / Time (beginning of measurement)
Balance Manufacturer
Balance Model
Balance Serial Number
Software Version
ID
Dotted line
Lot ID
Counting : Reference Sample Quantity
Counting : Reference Weight
Counting Result
Weighing Result
Weighing Result
Dotted line
Date / Time (end of measurement)
Name of Operator
Dotted line
The ISO/GLP-compliant record can contain the following lines:
-----------------------20-Jul-10
10:32AM
Citizen
Model
CX 220
Ser.no.
9223102
Ver.no.
r0.1.5.3
ID
1234567
-----------------------Calibration:
External
............
W-ID
32.905'C
Temperature
Set
+ 200.0000 g
Diff.
+ 0.1234 g
External Cal Done
Diff.
0.0000g
-----------------------20-Jul-10
10:32AM
Name:
................
------------------------
Dotted line
Date / Time (beginning of measurement)
Balance Manufacturer
Balance Model
Balance Serial Number
Software Version
ID
Dotted line
Calibration / Adjustment Mode
Blank Line
Weight ID
Temperature
Calibration Weight
Diff. After Calibration
Confirmation of Completed Calibration
Blank Line
Difference from Nominal Value after Calibration
Dotted line
Date / Time (end of measurement)
Name of Operator
Dotted line
96
9. Data Interface
Purpose
Your balance is equipped with an interface port for connection to a computer or other peripheral device.
You can use an on-line computer to change, start and/or monitor the functions of the balance and theapplication programs.
Features
Type of interface: Serial interface
Factory settings:
Operating mode: Full duplex
Transmission rate: 1,200 baud (9600)
Standard: RS-232
Parity: Odd (none)
Transmission rates: 300; 600; 1,200; 2,400; 4,800; 9,600; 19,200 baud 57600
Stop bits: 1 stop bit
Parity: Mark, space, odd, even, none
Handshake: None
Character format: 1 start bit, 8-bit ASCII, parity,1 or 2 stop bits
Print manually/automatically: Manual at
stability
Handshake: None
Preparation
• See “Pin Assignments”
Data output format of the balance : 26 characters
97
9.1 Output Format with 26 Characters
The following characters can be output, depending on the characters displayed on the balance :
Normal Operation
Position
1 2 3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
*
*
*
*
+
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
*
U
U
U
LF CR
or
*
*
*
*
-
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
*
U
U
U
LF CR
or
l
l
l
*
+
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
*
U
U
U
LF CR
* : Space
D : Digit or letter
U : Unit Symbol
Special Codes
Position
1 2
4
Carriage Return
Line Feed
ID code Character
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
-
-
-
-
-
-
-
O L
-
-
-
-
-
-
LF CR
or
-
-
-
-
-
-
-
U
L
-
-
-
-
-
-
LF CR
or
-
-
-
-
-
-
-
O r
-
-
-
-
-
-
LF CR
-
-
-
-
-
-
-
L
L
-
-
-
-
-
-
LF CR
-
-
-
-
-
-
-
H
H
-
-
-
-
-
-
LF CR
OL :
Or :
HH :
3
CR :
LF :
l
:
Space
Digit or letter
Unit Symbol
UL :
LL :
Carriage Return
Line Feed
98
Data Output Examples + 123.4567 g
Position
1
2
3
4
or
or
N
1
or
T
o
t
Position 1 - 4 :
Position 5
:
Position 6 - 20 :
Position 21
:
Position 22 - 24:
Position 25
:
Position 26
:
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
+
1
2
3
.
4
5
6
7
g
LF CR
+
6
1
7
.
2
8
3
5
t
LF CR
+
2
0
.
0
0
0
0
g
LF CR
+
6
0
.
0
0
0
0
g
LF CR
c
ID code Character or Space
Sign
Weight with Decimal Point; leading zeros = space
Space
Unit Symbol or Space
Line Feed
Carriage Return
99
ID code
characters
Meaning
nRef
Counting: Reference sample quantity
wRef
Piece Counting, Percentage Weighing : Reference weight
Qnt
Piece Counting: Quantity
pRef
Weighing in percent: Reference percentage
Pct
Weighing in percent: Reference percentage
Cnt
Animal weighing: No. of sub-weighing operations
xNt
Animal weighing: Calculated average
N1
Formulation, Totalization Net : N1
N
Formulation, Totalization : Net N
Tot
Formulation, Totalization : Total Weight
Pur
Density : Purity of Gold
Den
Density : Density of sample
9.2 Data Input Format
You can connect a computer to your balance to send commands via the balance interface port to control balance functions
and applications.
Format for commands
[
Command Code
Data
]
•[: it shows start of command frame.
•Command Code: it shows which functionality to be carried out for this command frame.
•Data: This field in frame is optional and it is intended to provide data information between Bi-directional communications.
•]: it shows end of command frame.
Commands
[W] : If host computer send this command to balance then balance will Send weight with current unit.
[T] : If host computer send this command then balance will do taring in balance. If stability is not achieved within 45 second
then it comes to that specific feature till that time it shows “-------“on LCM.
100
9.3 Cabling Diagram
• For connecting a computer or other peripheral device to the balance using the RS-232 protocol and cables up to 15m (50 ft.) long.
RS-232
Balance
DB 9 Female Connector
3
5
2
TxD
RxD
Gnd
Gnd
RxD
TxD
Peripheral Device
2 e.g. Computer or Printer
5
3
101
10. Error Codes
Display
Cause
Solution
Overload
Remove excess weight from the weighing pan.
Under load
• Keep weighing Pan on Weighing Shaft.
Check whether weighing pan is positioned
properly.
Weight set is to low for storing any reference at PCS,
%, Custom Unit or Check Weighing.
Increase weight on the pan.
While calibrating the scale, the load on the pan is
more than 10% of the capacity. (During power on
of the scale.)
Switch OFF the Balance and Switch ON again
without any load on the pan.
Calibration
• User does not keep any weight on the pan within
60 second.
• Weight load on the pan is not within the tolerance
limit.
• Add the calibration weight on the pan when
demanded by the balance
• Calibrate with the exact Calibration Weight.
GLP is ON and user tries to enter in to the User Menu
before the footer is printed.
Print the footer first, by pressing <CANCEL> key, and
then access the USER MENU.
Calibration
Display shows any weight other than 0.00 and user
tries to Calibrate the balance
Tare the balance or enter Calibration procedure
when “0.00 g” is displayed.
Incorrect value of TIME or DATE.
Enter proper value of TIME or DATE.
102
Display
Cause
Solution
Last stored PRINT option is AUTO or AUTO LOAD or
CONTINUOUS and user tries to set GLP ON from
USER MENU.
Change the print option to Print on REQUEST and
then turn GLP ON.
RTC not operational.
Contact Citizen Service center.
Error 2 Calibration Error + RTC Error.
Contact Citizen Service center.
Error 3 Calibration Error + RTC Error.
Contact Citizen Service center.
The weight readout
changes constantly
Unstable ambient conditions
A foreign object is caught between the load plate
and the balance/scale frame
Set up the balance/scale in another area Remove
the foreign object
The weight readout is
obviously wrong
The balance has not been calibrated / adjusted.
The balance was not zeroed before weighing.
Calibrate / Adjust the balance.
Tare or Zero the balance before weighing.
103
11. Care & Maintenance
Service
Regular servicing by a CITIZEN technician will extend the service life of your balance and ensure its continued weighing accuracy.
CITIZEN can offer you service contracts, with your choice of regular maintenance intervals.
The optimum maintenance interval depends on the operating conditions at the place of installation and on the individual
tolerance requirements.
Repairs
Repair work must be performed by trained service technicians. Any attempt by untrained persons to perform repairs may lead to
hazards for the user.
Cleaning
I Unplug the AC adapter from the wall outlet
(mains supply). If you have an interface cable connected to the balance/scale port, unplug it from the port.
I Make sure that no liquid enters the balance/scale housing
I Do not use any aggressive cleaning agents (solvents or similar agents)
• Clean the balance/scale using a piece of cloth which has been wet with a mild detergent (soap)
• After cleaning, wipe down the balance/scale with a soft, dry cloth
104
Cleaning Stainless Steel Surfaces
Clean all stainless steel parts regularly. Remove the stainless steel weighing pan and thoroughly clean it separately.
Use a damp cloth or sponge to clean any stainless steel parts on the scale. You can use any commercially available household
cleaning agent that is suitable for use on stainless steel. Clean stainless steel surfaces by wiping them down. Then clean the
weighing pan thoroughly, making sure to remove all residues. Use a damp cloth or sponge to wipe down any stainless steel parts
on the scale again. Afterwards, allow the scale to dry. If desired, you can apply oil to the cleaned surfaces as additional
protection.
I Do not use stainless steel cleaning agents that contain soda lye (caustic), acetic acid, hydrochloric acid, sulfuric acid or citric
acid. The use of scrubbing sponges made of steel wool is not permitted. Solvents are permitted for use only on stainless steel parts.
Safety Inspection
If there is any indication that safe operation of the balance/scale with the AC adapteris no longer warranted:
• Turn off the power and disconnect the equipment from AC power immediately
• Lock the equipment in a secure place to ensure that it cannot be used for the time being Safe operation of the balance/scale
with the
AC adapter is no longer ensured when:
• there is visible damage to the AC adapter.
• the AC adapter no longer functions properly.
• the AC adapter has been stored for a relatively long period under unfavorable conditions.
105
106
LIMITED WARRANTY
CITIZEN products are warranted against defects in materials and workmanship from the date of
delivery through the duration of the warranty period. During the warranty period Citizen will repair,
or, at its option, replace any components(S) that proves to be defective at no charge, provided that
the product is returned, freight prepaid, to CITIZEN.
This warranty does not apply if the product has been damaged by accident or misuse, exposed to
radioactive or corrosive materials, has foreign material penetrating to the inside of the product, or
as a result of service or modification by other than CITIZEN. In lieu of a properly returned warranty
registration card, the warranty period shall begin on the date of shipment to the authorized dealer.
No other express or implied warranty is given by Citizen Scale (i) Pvt. Ltd.
As warranty legislation differs from state to sta te and country to country, please contact citizen or your
local CITIZEN dealer for further details.
CITIZEN service center will repair the product free of charge subject to terms & condition mentioned below.
TERMS & CONDITION
1.It covers only weighing balance purchased from authorized channel and does not covers accessoris
like Batteri, Adaptor, RS232 cable, Pan, Pan support etc
2.It does not cover the product of which model and serial number has been altered, removed or defaced
and / or is open by unauthorized person and found void sticker has been tampered.
3.This warranty is non-transferable and applicable only to first end user purchasing the product from
authorized dealer.
4.For repair based on this warranty you need to hand over this product or send this product to address
mentioned in warranty card in original packing, enclosing copy of this warranty card.‘
5.Citizen Scale (I) Pvt. Ltd. shall not be liable for any consequential damages.
107
WARRANTY REGISTRATION
ISO 9001 : 2000 CERTIFIED
CITIZEN SCALE (I) PVT.LTD.
Citizen House, Plot No.50 A/B,
Govt. Ind. Estate, Charkop Kandivali (west).
Mumbai - 400 067, Maharashtra, India
e-mail :- [email protected]
web.www.citizenscales.com
Tel. No. :- +91-22-2860 7878
NAME :ADDRESS :-
TEL NO. :-
MODEL NO. :-
SERIAL NO. :-
PURCHASE DATE :-
BRANCH / DISTRIBUTOR / DEALER CONTACT DETAILS
WARRANTY
PERIOD :-
Owners Signature / Date
STAMP / SIGN
SEND YOUR WARRANTY CARD DULY FILL TO ABOVE ADDRESS FOR REGISTRATION
108
12. Dimensional Drawing
Analytical Balances
(CX / CY(0.1mg)Series
Balances)
Draft Shield High
Carat Balances
(CT Series Balances)
Draft Shield Low
165
78
165
78
169.5
239.5
325.5
255.5
341
271
97
97
67.5
231
342.5
67.5
231
342.5
189.5
189.5
1)
1)
212
212
171.5190.5 204.5
171.5190.5 204.5
29
29
Ø90
Ø90
152
152
109
Top Loading Precision Balances
(CG Series Balances)
No Draft Shield
Precision Balances
(CY Series Balances)
Draft Shield Low
165
78
169.5
210 X 198
255.5
271
128 X 128
89.5
96.5
67.5
231
67.5
342.5
231
342.5
208.5
189.5
1)
212
171.5
1)
204.55
212
48
171.5190.5
29
152
110
204.5
129.95
247
419.18
268.05
190.5
402
347
13. Specifications
Analytical Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External calibration weight (of at least accuracy class...)
Net Weight, approx.
Pan size
Weighing chamber height
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
g
mg
g
<+mg
<+mg
s
0
C
0
C
g
kg
mm
mm
mm
V~
Hz
VA
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
CX 301
CX 220
301
220
0.1
0.1
-301
-220
0.1
0.1
0.3
0.2
3 sec.
0
0
0
+ 10.... + 40 C (50 F to 104 F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
Internal
Internal
200 (E2)
200 (E2)
CX 120
120
0.1
-120
0.1
0.2
CX 65
65
0.1
-120
0.1
0.2
Internal
100 (E2)
Internal
50 (E2)
90 Ø
228.5
342.5 x 212 x 341
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
113
Analytical Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External calibration weight (of at least accuracy class...)
Net Weight, approx.
Pan size
Weighing chamber height
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
g
mg
g
<+mg
<+mg
s
0
C
0
C
g
kg
mm
mm
mm
V~
Hz
VA
CY 204
220
0.1
-220
0.1
0.2
3 sec.
+ 10.... + 400C (500F to 1040F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
External
200 (E2)
CY 120
120
0.1
-120
0.1
0.2
CY 54
60
0.1
-60
0.1
0.2
External
100 (E2)
External
50 (E2)
90 Ø
228.5
342.5 x 212 x 341
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
114
Precision Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External cal. wt. (of at least accuracy class..)
Net Weight, approx.
Pan size
Weighing chamber height
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
g
g
g
<+g
<+g
s
0
C
0
C
g
kg
mm
mm
mm
V~
Hz
VA
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
CY 120
CY 220
CY 320
120
220
320
0.001
0.001
0.001
-120
-220
-320
0.001
0.001
0.001
0.002
0.002
0.002
2 - 3 sec.
0
0
0
+ 10.... + 40 C (50 F to 104 F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
External
External
External
100 (F1)
200 (F1)
200 (F1)
CY 420
420
0.001
-420
0.001
0.002
CY 510
510
0.001
-510
0.001
0.002
CY 720
720
0.001
-720
0.001
0.002
CY 1003
1000
0.001
-100
0.002
0.002
External
200 (F1)
External
500 (F1)
External
500 (F1)
External
1000 (F1)
128 x 128
158.5
342.5 x 212 x 271
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
115
Precision Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External cal. wt. (of at least accuracy class..)
Net Weight, approx.
Pan size
Weighing chamber height
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
g
mg
g
<+mg
<+mg
s
0
C
0
C
g
kg
mm
mm
mm
V~
Hz
VA
CY 220C
CY 320C
220
320
0.001
0.001
-220
-320
0.001
0.001
0.002
0.002
2 - 3 sec.
+ 10.... + 400C (500F to 1040F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
Internal
Internal
200 (F1)
200 (F1)
CY 510C
510
0.001
-510
0.001
0.002
CY 1003C
1000
0.001
-100
0.002
0.002
Internal
500 (F1)
Internal
1000 (F1)
128 x 128
158.5
342.5 x 212 x 271
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
116
Top Loading Precision Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External cal. wt. (of at least accuracy class..)
Net Weight, approx.
Pan size
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
g
g
g
<+g
<+g
s
0
C
0
C
g
kg
mm
mm
V~
Hz
VA
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
CG 1202
CG 2202
1200
2200
0.01
0.01
-1200
-2200
0.01
0.01
0.02
0.02
2 - 3 sec.
0
0
0
+ 10.... + 40 C (50 F to 104 F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
External
External
1000 (F1)
2000 (F1)
CG 3102
3100
0.01
-3100
0.01
0.02
CG 4102
4100
0.01
-4100
0.01
0.02
CG 6102
6100
0.01
-6100
0.02
0.03
External
2000 (F1)
External
2000 (F1)
External
5000 (F1)
195 x 205
342.5 x 212 x 89.5
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
117
Top Loading Precision Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External cal. wt. (of at least accuracy class..)
Net Weight, approx.
Pan size
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
g
g
g
<+g
<+g
s
0
C
0
C
g
kg
mm
mm
V~
Hz
VA
CG 2202C
2200
0.01
-2200
0.01
0.02
2 - 3 sec.
+ 10.... + 400C (500F to 1040F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
Internal
2000 (F1)
CG 4102C
4100
0.01
-4100
0.01
0.02
CG 6102C
6100
0.01
-6100
0.02
0.03
Internal
2000 (F1)
Internal
5000 (F1)
195 x 205
342.5 x 212 x 89.5
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
118
High Capacity Precision Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External calibration weight (of at least accuracy class...)
Net Weight, approx.
Pan size
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
Kg
g
Kg
<g
<+g
s
0
C
0
C
Kg
kg
mm
mm
V~
Hz
VA
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
SSH 96
SSH 95
10
15
0.01
0.1
-10
-15
0.02
0.1
0.04
0.2
2 - 3 sec.
0
0
0
+ 10.... + 40 C (50 F to 104 F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
External
External
10 (E2)
10 (F1)
SSH 94
20
0.1
-20
0.1
0.2
SSH 94H
25
0.1
-25
0.1
0.2
External
20 (F1)
External
20 (F1)
400 x 300
517 x 302 x 130
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
119
High Capacity Precision Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External calibration weight (of at least accuracy class...)
Net Weight, approx.
Pan size
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
Kg
g
Kg
<+g
<+g
s
0
C
0
C
Kg
kg
mm
mm
V~
Hz
VA
SSH 92
SSH 93
50
35
1
0.1
-50
-35
1
0.1
2
0.2
2 - 3 sec.
+ 10.... + 400C (500F to 1040F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
External
External
50 (F1)
20 (F1)
SSH 91
60
1
-60
1
2
SSH 90
100
1
-100
1
2
External
50 (F1)
External
100 (F1)
400 x 300
517 x 302 x 130
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
120
Carat Balances
Model
Weighing Capacity
Readability (d)
Tare Range (Subtractive)
Repeatability (std. deviation)
Linearity
Response time (average)
Operating temperature range
Allowable ambient operating temperature
Calibration
External calibration weight (of at least accuracy class...)
Net Weight, approx.
Pan size
Weighing chamber height
Dimensions (W x D x H)
DC power source / Power requirements
Frequency
Power consumption (average)
Selectable weight units
Built-in-interface
Format
Parity
Transmission rates :
Handshake mode
ct
ct
ct
<+ct
<+ct
s
0
C
0
C
g
g
mm
mm
mm
V~
Hz
VA
CT 253
250
0.001
-250
0.001
0.002
3 sec.
0
0
0
+ 10.... + 40 C (50 F to 104 F)
0
0
0
+ 5.... + 50 C (41 F to 122 F)
External
50 (F1)
CT 603
600
0.001
-600
0.001
0.002
CT 1603
1600
0.001
-1600
0.001
0.002
External
100 (F1)
External
200 (F1)
90 Ø
158.5
342.5 x 212 x 271
DC Adapter, input 100 ~ 240 0.8A output 13V / 1.5A
50 / 60Hz
maximum 18; typical 9
gram, kilogram, pound, ounce, troy ounce, grain, pennyweight
carat, Milligram, momme, mesghal, Hong Kong tales, Singapore taels
Taiwan tales, baht
RS-232
1 start bit, 8-bit ASCII, parity, 1 or 2 stop bits
Mark, Space, Odd, even, none
300; 600; 1200; 2400; 4800; 9600; 19200; 57600 baud
None
121
14. Accessories (Option)
Data Printer
with Date / Time & Statistics
Remote Display
Calibration Weights
(F1) (ERTL, F2 with certificate) for further details, contact CITIZEN Dealers.
USB Interface
Density Kit
For determination of solids for determination of liquids with displacement body
Antitheft device
Cable and lock (for all models)
Dust Cover
122
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement