ACS-2702
ACS-2702
Intel Atom N2600 IP67 Certified and IP69K Compliant
Waterproof Box PC
User Manual
Release Date
Revision
Aug. 2015
V1.1
®2015 Aplex Technology, Inc.
All Rights Reserved.
Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: 886-2-82262881
Fax: 886-2-82262883
E-mail: [email protected]
URL: www.aplextec.com
Revision History
Reversion
1.0
1.1
ACS-2702 User Manual
Date
2015/07/08
2015/08/26
Description
Official Version
Modify IP Rating Spec.
1
Warning!___________________________
This equipment generates, uses and can radiate radio frequency energy and if
not installed and used in accordance with the instructions manual, it may cause
interference to radio communications. It has been tested and found to comply with
the limits for a Class A computing device pursuant to FCC Rules, which are designed
to provide reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a residential area is likely
to cause interference in which case the user at his own expense will be required to
take whatever measures may be required to correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed.
There are dangerous high voltages inside.
Disclaimer
This information in this document is subject to change without notice. In no event shall
Aplex Technology Inc. be liable for damages of any kind, whether incidental or
consequential, arising from either the use or misuse of information in this document or in
any related materials.
ACS-2702 User Manual
2
Packing List
Accessories (as ticked) included in this package are:
□ Adaptor
□ Driver & manual CD disc
□ Other.___________________(please specify)
Safety Precautions
Follow the messages below to prevent your systems from damage:
◆ Avoid your system from static electricity on all occasions.
◆ Prevent electric shock. Don‘t touch any components of this card when the card
is power-on. Always disconnect power when the system is not in use.
◆ Disconnect power when you change any hardware devices. For instance, when
you connect a jumper or install any cards, a surge of power may damage the
electronic components or the whole system.
ACS-2702 User Manual
3
Table of Contents
Revision History…………………………………………………………………………………………….1
Warning!/Disclaimer………………..............................…………………………….……..….2
Packing List/Safety Precautions.....………………………………………………………………..3
Chapter 1
Getting Started
1.1 Features……………………………………………………………………………………………5
1.2 Specifications……………………………………………………………………………………5
1.3 Dimensions……………………………………………………………………………………….6
1.4 Brief Description of ACS-2702……………………………………………………………7
Chapter 2
Hardware
2.1 Motherboard Introduction……..……………..…………………..………………..…..8
2.2 Specifications……………………………….……………………………..…………………...8
2.3 Jumpers Setting and Connectors…………..............................................12
Chapter 3
BIOS Setup
3.1 Operations after POST Screen.............................................................21
3.2 BIOS Setup Utility….............................................................................21
3.3 Main Settings…....................................................................................22
3.4 Advanced Settings...............................................................................23
3.5 Chipset Settings...................................................................................29
3.6 Boot Settings…....................................................................................32
3.7 Security Settings..................................................................................34
3.8 Save and Exit Settings.........................................................................35
Chapter 4
Installation of Drivers
4.1 Intel Chipset Driver.…………………………………………..…….………………………38
4.2 Intel Graphics Media Accelerator Driver………………....……….……………..41
4.3 Intel (R) Network Adapter……..………………………………….…………………….44
4.4 Realtek ALC662 HD Audio Driver Installation……………….…….……………46
Figures
Figure 1.1: Dimensions of ACS-2702…………....………………………………...……...6
Figure 1.2: Overview of ACS-2702……………………………………………….....……...7
Figure 2.1: Mainboard Dimensions……………………………..………………..………10
Figure 2.2: Jumpers and Connectors Location_ Board Top…………………....11
Figure 2.3: Jumpers and Connectors Location_ Board Bottom………………11
ACS-2702 User Manual
4
Chapter 1
Getting Started
1.1 Features

Fanless design

Intel Atom N2600 1.6GHz CPU built-in

Onboard 2GB DDR III 800MHz

Wide Range 9~36V DC Power Input

IP67 Certified and IP69K Compliant
1.2 Specifications
System
Processor
System Chipset
System Memory
Outside I/O Ports
Storage
Expansion Slots
OS Support
Intel Atom Processor N2600 1.6GHz CPU
Intel NM10 Express Chipset
Onboard 2GB DDR III 800MHz
2 x USB 2.0 type A(by 1 x M12 8pin connector)
1 x GbE LAN by Realtek RTL8111E(M12 connector)
1 x RS-232 DB-9, COM2(M12 connector)
1 x RS-232/422/485 DB-9, COM1, Default RS-232 (M12 connector)
1 x VGA (M12 connector)
1 x DC Power (M12 connector)
1 x 2.5” SATA II HDD
1 x SD slot, up to 32GB
1 x Internal Mini-PCIe slot half size
Windows embedded standard 7, Windows 7 Pro for embedded,
Windows CE 6.0
Power
Power Input
Power Consumption
9~36V DC
MAX: 10.1W
Mechanical
Construction
Mounting
IP Rating
Dimension
Net Weight
Stainless Steel Chassis
Wall Mount
IP67 Certified and IP69K Compliant
200 x 250 x 53 mm
3.2Kg
Environmental
ACS-2702 User Manual
5
Operating Temperature
Storage Temperature
Storage Temperature
-20~60 °C
-40~85 °C
10%~90%@ 40℃, non-condensing
Certificate
Meet CE / FCC
1.3 Dimensions
Figure 1.1: Dimensions of ACS-2702
ACS-2702 User Manual
6
1.4 Brief Description of ACS-2702
The ACS-2702 is a fanless high-efficiency thermal solution Box PC, powered by Intel
Atom Processor N2600 1.6GHz CPU and supporting 2GB DDR3 800 MHz onboard. It comes
with 2 x USB 2.0, 1 x LAN, 2 x COM ports, 1 x VGA and 1 x DC Power all by M12 connector. It
supports 1 x 2.5” SATAII HDD space, 1 x SD slot up to 32GB, and 9~36V DC wide-ranging
power input, and it is IP67 certified and IP69K compliant waterproof. It is ideal for Industrial
Automation, Factory Automation, Machine Vision, Process Control, Data Terminal, TI,
Surveillance, etc. and running factory operations from small visual interface and maintenance
applications to large control process applications. The ACS-2702 works very well along with
any of our Display series and it absolutely can provide an easy way to perform control and
field maintenance.
Figure 1.2: Overview of ACS-2702
ACS-2702 User Manual
7
Chapter 2
Hardware
2.1 Motherboard Introduction
SBC-7106 is a 4" industrial motherboard developed on the basis of Intel Cedarview-M
Processors and NM10, which provides abundant peripheral interfaces to meet the needs of
different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE
configuration, one VGA port, one HDMI port, one LVDS interface. To satisfy the special needs
of high-end customers, CN1 and CN2 and CN3 richer extension functions. The product is
widely used in various sectors of industrial control.
2.2 Specifications
Specifications
Board Size
170mm x 113mm
CPU Support
Intel Atom N2600 /1.60GHz (2cores,3.5W, onboard)
Intel Atom D2550 /1.86GHz(2cores,10W, option)
Chipset
Intel NM10 Express
Memory Support
Onboard 2GB DDRIII SDRAM (N2600)
Onboard 4GB DDRIII SDRAM (D2550)
Graphics
Integrated Intel GMA 3600 (N2600)
Integrated Intel GMA 3650 (D2550)
Display Mode
1 x CRT Port
1 x HDMI Port
1 x LVDS1 (18/24-bit single LVDS)
Support
Up to 1920 x1200 for CRT
Resolution
Up to 1920 x1200 for HDMI
Up to 1366 x768 for LVDS1 (N2600)
Up to 1440 x 900 for LVDS1 (D2550)
Dual Display
CRT+LVDS1
CRT+HDMI
LVDS1+HDMI
Super I/O
Winbond W83627UHG-E
BIOS
AMIBIOS
ACS-2702 User Manual
8
Storage
1 x SATA Connector (7P)
1 x SATA Connector (7P+15P)
1 x SD Socket (USB to SD)
Ethernet
2 x PCIe Gbe LAN by Realtek RTL8111E
2 x USB 2.0 (type A)stack ports (USB4/USB5)
USB
2 x USB 2.0 Pin header for CN3 (USB2/USB3)
2 x USB 2.0 Pin header for CN1 (USB0/USB1)
1 x USB 2.0 for MPCIE1 (USB7)
1 x RS232/RS422/RS485 port, DB9 connector for external (COM1)
pin 9 w/5V/12V/Ring select
Serial
1 x RS232 port, DB9 connector for external (COM2)
pin 9 w/5V/12V/Ring select
1 x RS422/485 header for CN2 (COM3)
2 x UART for CN3 (COM5,COM6)
Digital I/O
8-bit digital I/O by Pin header (CN2)
4-bit digital Input
4-bit digital Output
4-bit digital I/O by Pin header (CN3)
2-bit digital Input
2-bit digital Output
Battery
Support CR2477 Li battery by 2-pin header
Audio
Support Audio via Realtek ALC662 HD audio codec
Support Line-in, Line-out, MIC by 2x6-pin header
Keyboard /Mouse
1 x PS2 keyboard/mouse by 1x6 box pin header (CN3)
Expansion Bus
1 x mini-PCI-express slot
1 x PCI-express (CN3)
Touch Ctrl
1 x Touch ctrl header for TCH1 (COM4)
Power
Wide Range DC10V~30v input
Management
Switches and
LED Indicators
1 x 3-pin power input connector
1 x Power on/off switch (CN1)
1 x Reset switch (CN1)
1 x Power LED status (CN1)
1 x HDD LED status (CN1)
1 x Buzzer
ACS-2702 User Manual
9
External I/O port
2 x COM Ports (COM1/COM2)
2 x USB 2.0 Ports (stack)
2 x RJ45 GbE LAN Ports
1 x HDMI Port
1 x Stack audio Jack (Line out)
Watchdog Timer
Software programmable 1 – 255 second by Super I/O
Temperature
Operating: -20℃ to 70℃
Storage: -40℃ to 85℃
Humidity
5% - 95%, non-condensing, operating
Power
12V /0.95A (Intel Atom N2600 processor with 2GB DDR3 DRAM)
Consumption
Meet CE/FCC class A
EMI/EMS
(units :mm)
Figure 2.1: Motherboard Dimensions
ACS-2702 User Manual
10
2.2.1 Jumpers Setting and Connectors
Board Top
Figure 2.2: Jumpers and Connectors Location_ Board Top
Board Bottom
Figure 2.3: Jumpers and Connectors Location_ Board Bottom
ACS-2702 User Manual
11
2.3 Jumpers Setting and Connectors
1.
JP5:
(2.0mm Pitch 1X2 box Pin Header), ATX Power and Auto Power on jumper setting.
JP5
Open
Close
2.
Mode
ATX Power
Auto Power on (Default)
JP3:
(2.0mm Pitch 1X2 Pin Header)CMOS clear jumper, CMOS clear operation will
permanently reset old BIOS settings to factory defaults.
JP3
Open
CMOS
NORMAL (Default)
Close 1-2
Clear CMOS
Procedures of CMOS clear:
a) Turn off the system and unplug the power cord from the power outlet.
b) To clear the CMOS settings, use the jumper cap to close pins 1 and 2 for about 3
seconds then reinstall the jumper clip back to pins open.
c) Power on the system again.
d) When entering the POST screen, press the <F1> or <DEL> key to enter CMOS Setup
Utility to load optimal defaults.
e) After the above operations, save changes and exit BIOS Setup.
Model
SBC-7106-N2600
SBC-7106-N2600-P
SBC-7106-D2550
3.
BAT1 :
(1.25mm Pitch 1X2 box Pin Header) 3.0V Li battery is embedded to provide power for
CMOS.
Pin#
Pin1
PIN2
4.
JP3
No
No
Yes
Signal Name
VBAT
Ground
DC_IN1:
(5.08mm Pitch 1x3 Pin Connector),DC9V~32V System power input connector。
ACS-2702 User Manual
12
5.
Pin#
Pin1
Pin2
Pin3
Power Input
DC+9V~32V
Ground
FG
Model
SBC-7106-N2600
SBC-7106-N2600-P
SBC-7106-D2550
DC_IN1
180°Connector
45°Connector
45°Connector
CPU_FAN1:
(2.54mm Pitch 1x3 Pin Header), Fan connector, cooling fans can be connected directly
for use. You may set the rotation condition of cooling fan in menu of BIOS CMOS Setup.
Pin#
1
2
3
Signal Name
Ground
VCC
Rotation detection
Note:
Output power of cooling fan must be limited under 5W.
Model
SBC-7106-N2600
SBC-7106-N2600-P
SBC-7106-D2550
6.
CPU_FAN1
No
No
Yes
VGA1:
(CRT 2.0mm Pitch 2X6 Pin Header), Video Graphic Array Port, Provide 2x6Pin cable to
VGA Port.
Signal Name
CRT_RED
CRT_GREEN
CRT_BLUE
CRT_H_SYNC
CRT_V_SYNC
Ground
Pin#
1
3
5
7
9
11
Pin#
2
4
6
8
10
12
Signal Name
Ground
Ground
VGA_EN
CRT_DDCDATA
CRT_DDCCLK
Ground
VGA hot plug setting for Windows XP:
VGA1(Pin Header)
Function
ACS-2702 User Manual
13
Pin4-Pin6(Close)
VGA Simulation Disabled
Pin4-Pin6(Open)
VGA Simulation Enabled
use the 2.0mm jumper cap to close pin 4 and pin6
7.
HDMI1:
(HDMI 19P Connector), High Definition Multimedia Interface connector.
8.
JP1:
(2.0mm Pitch 2x3 Pin Header), COM1 jumper setting, pin 1~6 are used to select signal
out of pin 9 of COM1 port.
JP1 Pin#
Close 1-2
Close 3-4
Close 5-6
9.
10.
11.
Function
COM1 RI (Ring Indicator) (default)
COM1 Pin9=+5V
(option)
COM1 Pin9=+12V
(option)
S_232:
(Switch), COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial
signal output.
Function
S_232 Pin#
RS232 (Default)
ON: Pin1, Pin2, Pin3, Pin4
RS422 (option)
OFF: Pin1, Pin2, Pin3, Pin4
RS485 (option)
OFF: Pin1, Pin2, Pin3, Pin4
S_422:
(Switch), COM1 setting, it provides selectable RS232 or RS422 or RS485 serial signal
output.
Function
S_422 Pin#
RS232 (Default)
OFF: Pin1, Pin2, Pin3, Pin4
RS422 (option)
ON: Pin1, Pin2, Pin3, Pin4
RS485 (option)
ON: Pin1, Pin2, Pin3, Pin4
COM1:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a
direct connection to serial devices. COM1 port is controlled by pins No.1~6 of
JP1,select output Signal RI or 5V or 12V, For details, please refer to description of JP1
and S_232 and S_422 setting.
ACS-2702 User Manual
14
RS232 (Default):
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP1 select Setting (RI/5V/12V)
BIOS Setup:
Advanced/W83627UHG Super IO Configuration/Serial Port
1 Configuration【RS-232】
RS422 (option):
Pin#
Signal Name
1
422_RX+
2
422_RX3
422_TX4
422_TX+
5
Ground
6
NC
7
NC
8
NC
9
NC
BIOS Setup:
Advanced/W83627UHG Super IO Configuration/Serial Port
1 Configuration【RS-422】
RS485 (option):
Pin#
1
NC
2
NC
3
4854
485+
5
Ground
6
NC
7
NC
ACS-2702 User Manual
Signal Name
15
8
NC
9
NC
BIOS Setup:
Advanced/W83627UHG Super IO Configuration/Serial Port
1 Configuration【RS-485】
12.
JP2:
(2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select signal
out of pin 9 of COM2 port.
JP2 Pin#
Function
Close 1-2
COM2 RI (Ring Indicator) (default)
Close 3-4
COM2 Pin9=+5V
(option)
Close 5-6
COM2 Pin9=+12V
(option)
13.
COM2:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a
direct connection to serial devices.
Pin#
1
2
3
4
5
6
7
8
9
14.
Signal Name
DCD# (Data Carrier Detect)
RXD (Received Data)
TXD (Transmit Data)
DTR (Data Terminal Ready)
Ground
DSR (Data Set Ready)
RTS (Request To Send)
CTS (Clear To Send)
RI (Ring Indicator)
TCH1:
(2.0mm Pitch 1x6 box Pin Header), internal Touch controller connector.
Pin#
1
2
3
4
5
6
ACS-2702 User Manual
Signal Name
SENSE
X+
XY+
YGND_EARCH
16
15.
JTAG1(option):
(2.0mm Pitch 2x2 Pin Header), Touch eeprom program to write interface
Signal Name
3.3V
Pin#
1
2
Signal Name
C2D_BR
YC2CK_RST
3
4
Ground
16.
LED3:
LED STATUS. Green LED for Touch Power status.
17.
SATA_P:
(2.5mm Pitch 1x2 box Pin Header), Two onboard 5V output connectors are reserved
to provide power for SATA devices.
Pin#
Signal Name
1
+DC5V
2
Ground
Note:
Output current of the connector must not be above 1A.
18.
SATA2:
(SATA 7Pin), SATA Connectors, one SATA connectors are provided, with transfer speed
up to 3.0Gb/s.
19.
SATA1:
(SATA 7Pin+15Pin), SATA Connectors, one SATA connectors are provided, with transfer
speed up to 3.0Gb/s.
20.
SD1:
(SD card socket),Secure Digital Memory Card socket.
21.
MPCIE1:
(Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices
with USB2.0 and LPC and SMBUS and PCIe signal. MPCIe card size is 30x30mm.
22.
AUDIO:
(2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is used
to provide high-quality audio I/O ports. Line Out can be connected to a headphone or
amplifier. Line In is used for the connection of external audio source via a Line in cable.
MIC is the port for microphone input audio.
ACS-2702 User Manual
17
Signal Name
5V
LINE-OUT-L
FRONT_JD
LINE-IN-L
MIC-IN-L
GND_AUD
23.
Pin#
1
3
5
7
9
11
Pin#
2
4
6
8
10
12
Signal Name
GND_AUD
LINE-OUT-R
LINE1_JD
LINE-IN-R
MIC-IN-R
MIC1_JD
LINE_OUT:
(Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662 codec is used to
provide high quality audio I/O ports. Line Out can be connected to a headphone or
amplifier.
24.
USB45:
USB4/USB5:(Double stack USB type A), Rear USB connector, it provides up to 4
USB2.0 ports, High-speed USB 2.0 allows data transfers up to480 Mb/s ,support USB
full-speed and low-speed signaling.
Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A.
If the external USB device current exceeds 1.5A, please separate connectors into
different Receptacle.
25.
LAN1/LAN2:
LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M
RJ-45 Ethernet ports are provided. Used Realtek RTL8111E chipset, LINK LED
(green) and ACTIVE LED (yellow) respectively located at the left-hand and
right-hand side of the Ethernet port indicate the activity and transmission state
of LAN.
26.
BUZ1:
Onboard buzzer.
ACS-2702 User Manual
18
27.
LED1:
LED STATUS. Green LED for Motherboard Power status.
28.
LED2:
LED STATUS. Green LED for Motherboard Standby Power Good status.
29.
CN1:
(DF13-40P Connector),For expand output connector, It provides one 18/24bit single
channel LVDS, one Backlight control, two USB ports, one power led, one HDD LED,
one power on/off button, one RESET.
Function
Signal Name
12V_S0
BKLT_EN_OUT
Ground
LVDS_VDD5
LVDS_VDD3
LVDS
Ground
LA_DATAP0
LA_DATAP1
LA_DATAP2
LA_DATAP3
LA_CLKP
Ground
Ground
USB1
USB1_P
USB0
USB0_P
5V_USB01
5V_USB01
PWR LED
PWR_LED+
Ground
PWR ON/OFF PWRBTN_ON-
Pin#
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Signal Name
12V_S0
BKLT_CTRL
Ground
LVDS_VDD5
LVDS_VDD3
Ground
LA_DATAN0
LA_DATAN1
LA_DATAN2
LA_DATAN3
LA_CLKN
Ground
Ground
USB1_N
USB0_N
5V_USB01
5V_USB01
HDD_LED+
Ground
FP_RST-
Function
LVDS
USB1
USB0
USB1
HDD LED
RESET
INVT1:
(2.0mm Pitch 1x6 Pin wafer connector), Backlight control connector for LVDS.
Pin#
1
2
3
ACS-2702 User Manual
Signal Name
+DC12V
+DC12V
Ground
19
4
5
6
Ground
BKLT_EN_OUT
BKLT_CTRL
Note:
Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS menu.
30.
CN2:
(DF13-20P Connector), for expand output connector, it provides eight GPIO, one
RS422 or RS485.
Function
Signal Name
Pin#
Signal Name
Function
5V
SIO_GPIO61
SIO_GPIO63
5V_S5
2
1 5V_S5
5V
GPIO_IN2
4
3 GPIO_IN1
SIO_GPIO60
GPIO_IN4
6
5 GPIO_IN3
SIO_GPIO62
Ground
8
7 Ground
SIO_GPIO21
GPIO_OUT2
10
9 GPIO_OUT1
SIO_GPIO20
SIO_GPIO23
GPIO_OUT4
12
11 GPIO_OUT3
SIO_GPIO22
Ground
14
13 Ground
485 or 422
485+_422TX+
16
15 485-_422TX485 or 422
RS422
422_RX+
18
17 422_RXRS422
5V
5V_S0
20
19 5V_S0
5V
COM3 BIOS Setup:
Advanced/W83627UHG Super IO Configuration/Serial Port 3 Configuration
【RS-422】
Advanced/W83627UHG Super IO Configuration/Serial Port 3 Configuration
【RS-485】
32.
H3/H4/H5/H6:
CPU1 and U53 Heat Sink SCREW HOLES, Four screw holes for intel N2600 and NM10
Heat Sink assemble.
33.
H1/H2:
MPCIE1 SCREW HOLES, H1and H2 for mini PCIE card (30mmx30mm) assemble.
ACS-2702 User Manual
20
Chapter 3
BIOS Setup
3.1 Operations after POST Screen
After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS Setup.
After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as
follows and includes basic information on BIOS, CPU, memory, and storage devices.
3.2 BIOS Setup Utility
Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu
containing system summary information will appear.
ACS-2702 User Manual
21
3.3 Main Settings
ACS-2702 User Manual
22
System Time:
Set the system time, the time format is:
Hour: 0 to 23
Minute: 0 to 59
Second: 0 to 59
System Date
Set the system date, the date format is:
Day:
Note that the ‘Day’ automatically changes when you set the date.
Month:
01 to 12
Date:
01 to 31
Year:
1998 to 2099
3.4 Advanced Settings
3.4.1
PCI Subsystem Settings
PCI Bus Driver Versio V2.05.02
PCI Common Settings:
PCI Latency Timer:
[32 PCI Bus Clocks]
[64 PCI Bus Clocks]
ACS-2702 User Manual
23
[96 PCI Bus Clocks]
[128 PCI Bus Clocks]
[160 PCI Bus Clocks]
[192 PCI Bus Clocks]
[224 PCI Bus Clocks]
[248 PCI Bus Clocks]
VGA Palette Snoop:
[Disabled]
[Enabled]
PERR# Generation:
[Disabled]
[Enabled]
SERR# Generation:
[Disabled]
[Enabled]
3.4.2
ACPI Settings
Enable ACPI Auto Conf:
[Disabled]
[Enabled]
Enable Hibernation:
[Enabled]
[Disabled]
ACPI Sleep State:
[Both S1 and S3 available for OS to choose from ]
[Suspend Disabled]
[S1 only (CPU Stop Clock)]
[S3 only (Suspend to RAM)]
Lock Legacy Resources:
[Disabled]
[Enabled]
S3 Video Repost:
[Disabled]
[Enabled]
ACS-2702 User Manual
24
3.4.3
CPU Configuration
Processor Type
Intel(R) Atom(TM) CPU N2600
EMT64
Not Supported
Processor Speed
1600MHz
System Bus Speed
400MHz
Ratio Status
16
Actual Ratio
16
System Bus Speed
400MHz
Processor Stepping
30661
Microcode Revision
269
L1 Cache RAM
2x56 k
L2 Cache RAM
2x512 k
Processor Core
Dual
Hyper-Threading
Supported
Hyper-Threading:
[Enabled]
[Disabled]
Execute Disable Bit:
[Enabled]
[Disabled]
Limit CPUID Maximum:
[Disabled]
[Enabled]
3.4.4
Thermal Configuration
CPU Thermal Configuration
DTS SMM
[Disabled]
[Enabled]
Platform Thermal Configuration
Critical Trip Point
[POR]
Active Trip Point Lo [55 C]
Active Trip Point Hi [71C]
Passive Trip Point [95]
ACS-2702 User Manual
Passive TC1 Value
1
Passive TC2 Value
5
25
Passive TSP Value
3.4.5
10
IDE Configuration
SATA Port0
SATA Port1
Not Present
Not Present
SATA Controller(S):
[Enabled]
[Disabled]
Configure SATA as:
[IDE]
[AHCI]
Misc Configuration for hard disk
3.4.6
USB Configuration
USB Configuration
USB Devices:
1 Drive ,1 keyboard
Legacy USB Support:
[Enabled]
[Disabled]
EHCI Hand-off:
[Disabled]
[Enabled]
USB hardware delays a
USB transfer time-out:
[20 sec]
[10 sec]
[5 sec]
[1 sec]
Device reset time-out:
[20 sec]
[10 sec]
[30 sec]
[40 sec]
Device power-up delay
[Auto]
[Manual]
ACS-2702 User Manual
26
3.4.7
W83627UHG Super IO Configuration
W83627UHG Super IO ch W83627UHG
Serial Port 1 Configuration
UART Mode Selection:
[RS-232]
[RS-485]
[RS-422]
Serial Port 2 Configuration
Serial Port 3 Configuration
UART Mode Selection:
[RS-485]
[RS-422]
Serial Port 4 Configuration
Serial Port 5 Configuration
Serial Port 6 Configuration
3.4.8
W83627UHG HW Monitor
PC Health Status
3.4.9
System Temperature1
: +38
System Speed
: N/A
VCORE
: +0.968V
+12V
: +12.302V
+3.3V
: +3.320V
+1.5V
: +1.528V
AVCC
: +5.203V
VCC5V
: +5.216V
VSB5
: +5.203V
VBAT
: +3.334V
Serial Port Console Redirection
COM0
Console Redirection
[Enabled]
[Disabled]
Console Redirection Settings
Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
ACS-2702 User Manual
27
Console Redirection
[Disabled]
[Enabled]
Console Redirection Settings
3.4.10 PPM Configuration
PPM Configuration
EIST:
[Enabled]
[Disabled]
CPU C State Report
[Enabled]
[Disabled]
Enhanced C State
[Enabled]
[Disabled]
CPU Hard C4E
[Enabled]
[Disabled]
CPU C6 State
[Enabled]
[Disabled]
C4 Exit Timing
[Fast]
[Default]
[Slow]
C-state POPDOWN
[Enabled]
[Disabled]
C-state POPUP
[Enabled]
[Disabled]
ACS-2702 User Manual
28
3.5 Chipset Settings
3.5.1
Host Bridge
►Memory Frequency and Timing
►Intel IGD Configuration
******* Memory Information *******
Memory Frequency
800 MHz(DDR3)
Total Memory
2048 MB
DIMM#0
Not Present
DIMM#1
2048 MB
Memory Frequency and Timing
MRC Fast Boot
[Enabled]
ACS-2702 User Manual
29
[Disabled]
Max TOLUD
[Dynamic]
[1GB]
[1.25GB]
[1.5GB]
[1.75GB]
[2GB]
[2.25GB]
[2.5GB]
[2.75GB]
[3GB]
[3.25GB]
Intel IGD Configuration
IGFX – Boot Type
[VBIOS Default]
[VGA]
[LVDS]
[HDMI]
[VGA + LVDS]
[VGA + HDMI]
[LVDS + HDMI]
LCD Panel Type
[VBIOS Default]
[640x480,18bit]
[800x480,18bit]
[800x600,18bit]
[1024x600,18bit ]
[1024x768,18bit ]
[1280x768,18bit ]
[1280x800,18bit ]
[1280x1024,18bit]
[1366x768,18bit]
[1024x768,24bit]
[1280x768,24bit]
[1280x800,24bit]
[1280x1024,24bit]
[1366x768,24bit]
Panel Scaling
[Auto]
[Force Scaling]
[off]
ACS-2702 User Manual
30
Active LFP
[Maintain Aspect Ratio]
[LVDS]
IGD Clock Source
[No LVDS]
[EDP]
[External Clock]
Fixed Graphics Memory
[Internal Clock]
ALS Support
[128MB]
[256MB]
Back light Control
[Disabled]
[Enabled]
Back light Logic
[DC]
[PWM]
Back light Control Lev
[Positive]
[Negative]
[Auto]
[Disabled]
[Level 8]
[Level 1]
[Level 2]
[Level 3]
[Level 4]
[Level 5]
[Level 6]
[Level 7]
[Level 8]
[Level 9]
[Level 10]
[Level 11]
[Level 12]
[Level 13]
[Level 14]
[Level 15]
ACS-2702 User Manual
31
3.5.1
South Bridge
TPT Devices
PCI Express Root Port 0
PCI Express Root Port 1
PCI Express Root Port 2
PCI Express Root Port 3
DMI Link ASPM Control
[Enable]
[Disabled]
PCI-Exp. High Priorit
[Disabled]
[Enabled]
High Precision Event Timer Configuration
High Precision Timer
[Enabled]
[Disabled]
SLP_S4 Assertion Widt
[1-2 Seconds]
[2-3 Seconds]
[3-4 Seconds]
[4-5 Seconds]
3.6 Boot Settings
ACS-2702 User Manual
32
Setup Prompt Timeout
Bootup Numlock State
[1]
[On]
[off]
Quiet Boot
[Disabled]
[Enabled]
Fast Boot
[Enabled]
[Disabled]
Skip VGA
[Enabled]
[Disabled]
Skip USB
[Disabled]
[Enabled]
Skip PS2
CSM16 Module Version
Gatea20 Active
[Disabled]
[Enabled]
07.69
[Upon Request]
[Always]
Option ROM Messages
[Force BIOS]
[Keep Current]
Interrupt 19 Capture
[Immediate]
[Postponed]
Boot Option #1
Boot Option #2
…..
Hard Drive BBS Priorities
Sets the system boot order
[SATA PM:***…]
Boot Option #1
SATA PM:***…
******
Disabled
CSM Parameters
Launch CSM
[Always]
[Never]
Boot option filter
[UEFI and Legacy]
[Legacy only]
[UEFI only]
Launch PXE OpROM poli
[Do not Launch]
[UEFI only]
[Legacy only]
Launch Storage OpROM
[Legacy only]
[Do not Launch]
[UEFI only]
ACS-2702 User Manual
33
Launch Video OpROM po
[Do not Launch]
[UEFI only]
[Legacy only]
Other PCI device ROM
[UEFI OpROM]
[Legacy OpROM]
3.7 Security Settings
3.7.1
Administrator Password
3.7.2
User Password
ACS-2702 User Manual
34
Type the password with up to 20 characters and then press <Enter> key. This will clear
all previously typed CMOS passwords. You will be requested to confirm the password.
Type the password again and press <Enter> key. You may press <Esc> key to abandon
password entry operation.
To clear the password, just press <Enter> key when password input window pops up.
A confirmation message will be shown on the screen as to whether the password will
be disabled. You will have direct access to BIOS setup without typing any password
after system reboot once the password is disabled.
Once the password feature is used, you will be requested to type the password each
time you enter BIOS setup. This will prevent unauthorized persons from changing
your system configurations.
Also, the feature is capable of requesting users to enter the password prior to system
boot to control unauthorized access to your computer. Users may enable the feature
in Security Option of Advanced BIOS Features. If Security Option is set to System, you
will be requested to enter the password before system boot and when entering BIOS
setup; if Security Option is set to Setup, you will be requested for password for
entering BIOS setup.
3.8 Save & Exit Settings
ACS-2702 User Manual
35
Save Changes and Exit
Save & Exit Setup save Configuration and exit?
[Yes]
[No]
Discard Changes and Ext
Exit Without Saving Quit without saving?
[Yes]
[No]
Save Changes and Reset
Save & reset Save Configuration and reset?
[Yes]
[No]
Discard Changes and Reset
Reset Without Saving Reset without saving?
[Yes]
[No]
Save Changes
Save Setup Values Save configuration?
[Yes]
[No]
Discard Changes
Load Previous Values Load Previous Values?
[Yes]
[No]
Restore Defaults
Load Optimized Defaults Load optimized Defaults?
[Yes]
[No]
Save user Defaults
Save Values as User Defaults Save configuration?
[Yes]
[No]
Restore user Defaults
Restore User Defaults Restore User Defaults?
[Yes]
[No]
Launch EFI Shell from filesystem device
WARNING Not Found
[ok]
ACS-2702 User Manual
36
Chapter 4
Installation of Drivers
This chapter describes the installation procedures for software and drivers under the
windows 7. The software and drivers are included with the motherboard. The
contents include Intel chipset driver, VGA driver, LAN drivers, Audio driver
Installation instructions are given below.
Important Note:
After installing your Windows operating system, you must install first the Intel
Chipset Software Installation Utility before proceeding with the installation of
drivers.
ACS-2702 User Manual
37
4.1 Intel Chipset Driver
To install the Intel chipset driver, please follow the steps below.
Step 1. Select Intel (R) Chipset NM10 Express from the list
Step 2. Click Next to setup program.
ACS-2702 User Manual
38
Step 3. Read the license agreement. Click Yes to accept all of the terms of the
license agreement.
Step 4. Click Next to continue.
ACS-2702 User Manual
39
Step 5. Click Next.
Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove
any installation media from the drives.
ACS-2702 User Manual
40
4.2 Intel Graphics Media Accelerator Driver
To install the VGA drivers, follow the steps below to proceed with the installation.
Step 1.Select Intel(R) VGA Chipset from the list.
Step 2. Tick Automatically run WinSAT and enable the Windows Aero desktop
theme(if supported). Click Next.
ACS-2702 User Manual
41
Step 3. Read license agreement. Click Yes.
Step 4. Click Next.
ACS-2702 User Manual
42
Step 5. Click Next.
Step 6. To restart the computer, select Yes, I want to restart this computer now.
Then click Finish.
ACS-2702 User Manual
43
4.3 Intel (R) Network Adapter
To install the Intel (R) Network Adapter device driver, please follow the steps below.
Step 1. Select LAN Driver from the list.
Step 2. Click Next to continue.
ACS-2702 User Manual
44
Step 3. Click Install to begin the installation.
Step 5. Click Finish to exit the wizard.
ACS-2702 User Manual
45
4.4 Realtek ALC662 HD Audio Driver Installation
To install the Realtek ALC662 HD Audio Driver, please follow the steps below.
Step 1. Select Realtek AL662 Audio Driver from the list
Step 2. Click Next to continue.
ACS-2702 User Manual
46
Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the
installation.
ACS-2702 User Manual
47
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement