Portable Rechargeable Speaker XC-5209

Portable Rechargeable Speaker XC-5209
User Manual
Portable Rechargeable Speaker
Distributed by:
TechBrands by Electus Distribution Pty. Ltd.
320 Victoria Rd, Rydalmere
NSW 2116 Australia
Ph: 1300 738 555
Int’l: +61 2 8832 3200
Fax: 1300 738 500
www.techbrands.com
XC-5209
Specifications:
Output Power:
Bluetooth® Range:
Frequency Response:
Impedance:
Charging Time:
Playback Time:
At max. volume:
At 80% volume:
Dimensions:
2 x 3WRMS
10m
90Hz~18kHz
4 Ohm
3.5 – 4 hours
5 hours
6.5 – 7 hours
170 (L) x 65 (H) x 35 (W) mm
Power and Charging:
The unit has a built-in rechargeable battery. Before using the speaker, please follow
these steps to charge the unit first:
1. Using the supplied USB cable, plug into speaker and the other end into a
USB power terminal.
2. During charging, the LED will be red. Once it is fully charged the LED will turn
off.
3. When the battery is low, a voice will speak “Low Battery, Please Charge”.
Once the battery has been depleted, the speaker will power off.
Note:
Your battery will last longer if you follow these guidelines:
When charging for the first time, charge for at least 10 hours. The battery
will have a better performance if it is fully charged and fully discharged 3
times. Not discharging a battery completely before recharging again can
impact the battery’s lifetime.
Recharge and store the unit within the temperature ranges of 5°C and 35°C.
Do not charge for longer than 24 hours. Excessive charging may shorten the
battery’s life.
Bluetooth Pairing:
1. Slide the power button to the ON position, the blue LED at the front of the
speaker will be flashing quickly and the speaker will sound briefly “Bluetooth
mode on”. It is now in Bluetooth® pairing mode.
2. Turn on the Bluetooth® Technology pairing of your device, and search for
‘XC5209’. Select this name and input ‘000o’ as the password if prompted.
The speaker will sound “Matching OK”, and the blue LED at the front of the
speaker will flash slowly to show that the pairing has been successful.
3. Select the music to play from your device, or use as per the Operation
Instructions below.
NFC (Near Field Communication):
1. To use the NFC function, you must have an NFC enabled device. Ensure that
the NFC on your device is turned on, and hold your NFC enabled device over
the NFC logo on the speaker.
2. This will connect your device to the speaker, and any previous devices that
were connected will be disconnected.
3. Select the music to play from your device, or use as per the Operation
Instructions below.
AUX Link:
1. After powering on the unit, use a 3.5mm audio cable to connect your music
device with the speaker. The LED on the front will turn red and the speaker
will sound “Under Line-in Mode”.
2. Select the music to play from your device, or use as per the Operation
Instructions below.
Operation Instruction:
- Press the
button once to Play and Pause the music.
- If you press and hold the
button, the Bluetooth® will disconnect and
you will hear “Waiting for Connection”.
- Press the + or – buttons once to select the previous track or the next track.
- Press and hold the + or – buttons to increase or decrease the volume.
- In Bluetooth® mode (doesn’t work with 3.5mm audio cable), when there is
an incoming call, press
up.
to pick up the call, and press it again to hang
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement