B/E/M/S/X Series Calibration Procedure

B/E/M/S/X Series Calibration Procedure
CALIBRATION PROCEDURE
B/E/M/S/X Series
For NI-DAQ™mx
This document contains instructions for calibrating National Instruments
B, E, M, S, and X Series data acquisition (DAQ) devices.
This document does not discuss programming techniques or compiler
configuration. The NI-DAQmx driver contains online help files that have
compiler-specific instructions and detailed function explanations. You
can add these help files when you install NI-DAQmx on the calibration
computer.
Contents
Conventions ............................................................................................ 2
Software .................................................................................................. 3
Documentation ........................................................................................ 3
Calibration Interval ................................................................................. 4
Password ................................................................................................. 4
Test Equipment ....................................................................................... 4
Test Conditions ....................................................................................... 6
Calibration Procedure ............................................................................. 6
Initial Setup...................................................................................... 7
Self-Calibration................................................................................ 7
Checking Device Temperature Changes.......................................... 8
Verification Procedure ..................................................................... 9
Analog Input Verification......................................................... 10
Analog Output Verification ...................................................... 15
Counter Verification ................................................................. 18
Adjustment Procedure...................................................................... 20
Test Limits .............................................................................................. 23
B Series Test Limits......................................................................... 25
NI 6010—16-Bit Resolution .................................................... 25
NI 6013/6014/6015/6016—16-Bit Resolution ......................... 27
E Series Test Limits..........................................................................29
NI 6011E—16-Bit Resolution...................................................29
NI 6023E/6024E/6025E—12-Bit Resolution............................31
NI DAQCard-6024E—12-Bit Resolution.................................33
NI 6030E/6031E/6032E/6033E—16-Bit Resolution ................35
NI 6034E/6035E/6036E—16-Bit Resolution............................38
NI DAQCard-6036E—16-Bit Resolution.................................40
NI 6040E—12-Bit Resolution...................................................42
NI 6052E—16-Bit Resolution...................................................45
NI DAQCard-6062E—12-Bit Resolution.................................48
NI 6070E/6071E—12-Bit Resolution .......................................51
M Series Test Limits ........................................................................54
NI USB-6210/6211/6215/6218—16-Bit Resolution.................54
NI USB-6212/6216—16-Bit Resolution...................................56
NI 6220/6221/6224/6225/6229—16-Bit Resolution.................58
NI 6250/6251/6254/6255/6259—16-Bit Resolution.................60
NI 6280/6281/6284/6289—18-Bit Resolution..........................63
S Series Test Limits..........................................................................67
NI 6110/6111—12-Bit Resolution ............................................67
NI 6115—12-Bit Resolution .....................................................69
NI 6120—16-Bit Resolution .....................................................71
NI 6122/6123—16-Bit Resolution ............................................73
NI PXIe-6124—16-Bit Resolution............................................74
NI 6132/6133—14-Bit Resolution ............................................76
NI 6143—16-Bit Resolution .....................................................77
X Series Test Limits .........................................................................78
NI 632x—16-Bit Resolution .....................................................78
NI 634x—16-Bit Resolution .....................................................80
NI 6351/6353—16-Bit Resolution ............................................82
NI 6356/6358/6366/6368—16-Bit Resolution..........................85
NI 6361/6363—16-Bit Resolution ............................................87
Conventions
The following conventions are used in this manual:
»
The » symbol leads you through nested menu items and dialog box options
to a final action. The sequence File»Page Setup»Options directs you to
pull down the File menu, select the Page Setup item, and select Options
from the last dialog box.
This icon denotes a note, which alerts you to important information.
This icon denotes a caution, which advises you of precautions to take to
avoid injury, data loss, or a system crash. When this symbol is marked on
B/E/M/S/X Series Calibration Procedure
2
ni.com
a product, refer to the Read Me First: Safety and Electromagnetic
Compatibility for information about precautions to take.
bold
Bold text denotes items that you must select or click in the software, such
as menu items and dialog box options. Bold text also denotes parameter
names and hardware labels.
italic
Italic text denotes variables, emphasis, a cross-reference, or an introduction
to a key concept. Italic text also denotes text that is a placeholder for a word
or value that you must supply.
monospace
Monospace text denotes text or characters that you should enter from the
keyboard, sections of code, programming examples, and syntax examples.
This font is also used for the proper names of disk drives, paths, directories,
programs, subprograms, subroutines, device names, functions, operations,
variables, filenames, and extensions.
monospace italic
Italic text in this font denotes text that is a placeholder for a word or value
that you must supply.
Platform
Text in this font denotes a specific platform and indicates that the text
following it applies only to that platform.
Software
Calibration requires the latest NI-DAQmx driver. NI-DAQmx includes
high-level function calls to simplify the task of writing software to calibrate
devices. The driver supports many programming languages, including
LabVIEW, LabWindows™/CVI™, C/C++, C#, and Visual Basic .NET.
Documentation
The following documents are your primary references for writing your
calibration utility with NI-DAQmx:
•
The DAQ Getting Started guides for NI-DAQ 9.2 or later provides
instructions for installing and configuring NI-DAQ devices.
NI USB-621x users should refer to the NI-DAQmx for USB Devices
Getting Started Guide.
•
The NI-DAQmx Help includes information about creating applications
that use the NI-DAQmx driver.
•
The NI-DAQmx C Reference Help includes information about the
functions in the driver.
© National Instruments Corporation
3
B/E/M/S/X Series Calibration Procedure
•
E Series Calibration Fixture Installation Guide provides information
on installing and operating the E/M/S Series calibration hardware
adapter.
•
The NI 6010 Help, E Series User Manual, M Series User Manual,
NI USB-621x User Manual, S Series User Manual, NI 6124/6154 User
Manual, or X Series User Manual provides information about your
DAQ device.
•
The specifications document for your DAQ device provides detailed
specifications.
Calibration Interval
B/E/M/S/X Series devices should be calibrated at a regular interval as
defined by the measurement accuracy requirements of your application.
National Instruments recommends that you routinely perform a complete
calibration at least once every year (once every two years for some
M/S/X Series devices). You can shorten this interval based on the accuracy
demands of your application or requirements of your processes.
Password
The default password for password-protected operations is NI.
Test Equipment
National Instruments recommends that you use the instruments in Table 1
for calibrating a B/E/M/S/X Series device.
Caution For compliance with Electromagnetic Compatibility (EMC) requirements, this
product must be operated with shielded cables and accessories. If unshielded cables or
accessories are used, the EMC specifications are no longer guaranteed unless all
unshielded cables and/or accessories are installed in a shielded enclosure with properly
designed and shielded input/output ports.
Table 1. Recommended Equipment
Equipment
Recommended Model
Requirements
Calibrator
Fluke 5700A
If this instrument is unavailable, use a high-precision voltage
source that is at least 50 ppm (0.005%) accurate for
12-bit devices, and 10 ppm (0.001%) accurate for 14-, 16-,
and 18-bit devices.
DMM
NI 4070
If this instrument is unavailable, use a multiranging 6 1/2-digit
DMM with an accuracy of 40 ppm.
B/E/M/S/X Series Calibration Procedure
4
ni.com
Table 1. Recommended Equipment (Continued)
Equipment
Recommended Model
Requirements
Counter
Agilent 53131A
If this instrument is unavailable, use a counter accurate to 0.01%.
PXI chassis
NI PXI-1042,
NI PXI-1042Q
Use with PXI modules.
PXI Express chassis
NI PXIe-1062Q
Use with PXI Express modules.
Low thermal copper
EMF plug-in cable
Fluke 5440A-7002
Do not use standard banana cables.
Shielded DAQ cable
NI SH68-68-EP,
NI SH68-68-EPM
Use with B/E/M/S Series devices with 68-pin SCSI II
connectors.
NI SHC68-68-EP,
NI SHC68-68-EPM,
NI SHC68-68
Use with E/M/S/X Series devices with 68-pin VHDCI
connectors.
NI SH1006868
Use with E Series devices with 100-pin connectors.*
NI SH37F-37M-1
Use with B/M Series devices with 37-pin D-SUB connectors.
NI E/M/S Series calibration
hardware adapter
Connects your calibration equipment to your 68-pin
E/M/S/X Series device.
DAQ accessory
If you programmatically control this fixture, you will not need to
disconnect and reconnect cables at each step of the procedure.†
(NI 61xx Devices) S Series devices must use revision B or later of
the calibration adapter.
*
NI SCC-68
I/O connector block with screw terminals, general breadboard
area, bus terminals, and four expansion slots for SCC signal
conditioning modules.
NI SCB-68
Shielded I/O connector block with 68 screw terminals for easy
signal connection to 68- or 100-pin DAQ devices.
NI CB-68LP,
NI CB-68LPR,
NI TBX-68
Low-cost termination accessories with 68 screw terminals for
easy connection of field I/O signals to 68-pin DAQ devices.
NI BNC-2110
Desktop and DIN rail-mountable BNC adapter you can connect
to DAQ devices.
NI CB-37F-LP
Low-cost termination accessory with 37 screw terminals for easy
connection of field I/O signals to 37-pin DAQ devices.
Connect the 68-pin cable labeled MIO-16 to the accessory. The 68-pin cable labeled Extended I/O remains unconnected.
†
For M/S/X Series devices with two connectors, you will need to disconnect the calibration equipment from Connector 0
and reconnect to Connector 1 midway through the verification procedure.
© National Instruments Corporation
5
B/E/M/S/X Series Calibration Procedure
Test Conditions
Follow these guidelines to optimize the connections and the environment
during calibration.
•
Keep connections to the device as short as possible. Long cables and
wires can act as antennae, which could pick up extra noise that would
affect measurements.
•
Use shielded copper wire for all cable connections to the device.
Use twisted-pair wire to eliminate noise and thermal offsets.
•
Maintain the ambient temperature between 18 and 28 °C. The device
temperature will be greater than the ambient temperature. Refer to the
Calibration Procedure section for more information about calibration
temperatures and temperature drift.
•
For valid test limits, maintain the device temperature within ±1 °C
from the last self-calibration and ±10 °C from the last external
calibration.
•
Keep relative humidity below 80%.
•
Allow adequate warm-up time (generally between 15 and 30 minutes
for most DAQ devices) to ensure that the measurement circuitry is at a
stable operating temperature. Refer to your DAQ device specifications
document for the recommended warm-up time for your device.
Calibration Procedure
The calibration process has six steps.
1.
Initial Setup—Configure your device in NI-DAQmx.
2.
Self-Calibration—Adjust the self-calibration constants of the device.
3.
Checking Device Temperature Changes—Verify that the current
device temperature will not cause you to incorrectly calibrate your
device.
4.
Verification Procedure—Verify the existing operation of the device.
This step allows you to confirm that the device was operating within
its specified range prior to calibration.
5.
Adjustment Procedure—Perform an external calibration that adjusts
the device calibration constants with respect to a known voltage
source.
6.
Reverification—Perform another verification to ensure that the device
is operating within its specifications after adjustment.
B/E/M/S/X Series Calibration Procedure
6
ni.com
These steps are described in detail in the following sections. Although NI
recommends that you verify all ranges, you can save time by checking only
the ranges used in your application.
Initial Setup
The device must be configured in Measurement & Automation Explorer
(MAX) to communicate with NI-DAQmx.
Complete the following steps to configure a device in MAX.
1.
Install the NI-DAQmx driver software.
2.
Power off the host computer or chassis that will hold the device and
install the device.
3.
Power on the computer or chassis and launch Measurement &
Automation Explorer (MAX).
4.
Configure the device identifier and select Self-Test to ensure that the
device is working properly.
Note When a device is configured with MAX, it is assigned a device identifier. Each
function call uses this identifier to determine which DAQ device to calibrate.
Self-Calibration
Self-calibration should be performed after the device has warmed up for the
recommended time period—generally between 15 and 30 minutes for most
DAQ devices. Refer to your DAQ device specifications document for the
recommended warm-up time for your device. Call self-calibration before
doing the first verification. This function measures the onboard reference
voltage of the device and adjusts the self-calibration constants to account
for any errors caused by short-term fluctuations in the environment.
Disconnect all external signals when you self-calibrate a device.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxSelfCal with the following
parameter:
deviceName: dev1
© National Instruments Corporation
7
B/E/M/S/X Series Calibration Procedure
You also can initiate self-calibration using MAX, by completing the
following steps.
1.
Launch MAX.
2.
Select My System»Devices and Interfaces»your device.
3.
Initiate self-calibration using one of the following methods:
•
Click Self-Calibrate in the upper right corner of MAX.
•
Right-click the name of the device in the MAX configuration tree
and select Self-Calibrate from the drop-down menu.
Checking Device Temperature Changes
Device temperature changes (greater than ±10 °C since the previous
external calibration or greater than ±1 °C since the previous
self-calibration) can cause you to incorrectly calibrate your device. After
self-calibrating your device (as described in the Self-Calibration section),
complete the following steps to compare the current device temperature to
the temperatures measured during the last self-calibration and external
calibration.
1.
Read the current temperature measured by the device by using the
DevTemp property node.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxGetCalDevTemp with the
following parameter:
deviceName: dev1
2.
Get the temperature of the device recorded during the last
self-calibration by using the SelfCal.LastTemp property node.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxGetSelfCalLastTemp with
the following parameter:
deviceName: dev1
If the difference between the current temperature and the temperature
from the last self-calibration is greater than 1 °C, the limits in the
calibration tables are not valid.
B/E/M/S/X Series Calibration Procedure
8
ni.com
3.
Get the temperature of the device recorded during the last external
calibration by using the ExtCal.LastTemp property node.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxGetExtCalLastTemp with
the following parameter:
deviceName: dev1
If the difference between the current temperature and the temperature
from the last external calibration is greater than 10 °C, the limits in the
calibration tables are not valid.
The maximum temperature change for most DAQ devices is ±10 °C. To find the
valid temperature drifts for your B/E/M/S/X device, refer to the Absolute Accuracy table(s)
in your DAQ device specifications document.
Note
You also can read the current device temperature, the temperature during the
last self-calibration, and the temperature during the last external calibration in MAX.
Launch MAX, select My System»Devices and Interfaces»your device, and then click the
Calibration tab.
Note
If the device temperature is outside the maximum range, you should choose
one of the following options:
•
Change the test limits to include the additional error due to temperature
drift. Refer to your DAQ device specifications document for more
information.
•
Change the system so that the temperature will be closer to the
temperature recorded during the last external calibration.
Verification Procedure
Verification determines how well the DAQ device is meeting its
specifications. By performing this procedure, you can see how your device
has operated over time. You can use this information to help determine the
appropriate calibration interval for your application.
The verification procedure is divided into the major functions of the device.
Throughout the verification process, use the tables in the Test Limits
section to determine if your device needs to be adjusted.
© National Instruments Corporation
9
B/E/M/S/X Series Calibration Procedure
Analog Input Verification
Since B/E/M/S/X Series devices have many different ranges, you must
check measurements for each available range.
(B/E/M/X Series [MIO] Devices) Because there is only one analog-to-digital
converter (ADC) on B/E/M Series and X Series NI 632x/634x/6351/6353/
6361/6363 devices, you must perform verification on all ranges of one
analog input channel in differential mode. (Optional) Then, perform
verification on one range of all remaining analog input channels in
differential mode to verify that the device mux and analog input lines are
operating properly.
(S/X Series [Simultaneous MIO] Devices) You must perform verification
on all ranges of all analog input channels of S Series and X Series
NI 6356/6358/6366/6368 devices in differential mode.
The test limits used in this document assume a maximum temperature drift of
±10 °C from the last external calibration, and a maximum temperature drift of ±1 °C from
the last self-calibration. Refer to the Calibration Procedure section for more information
and instructions on reading your device temperature and comparing it against the device
temperature during the last external calibration.
Note
Complete the following steps to check the performance of the analog input.
1.
Connect the calibrator to the device. Refer to Table 2 to determine
connections between the device and the calibrator.
If your calibrator has a guard connection, connect that terminal to AI GND. If your
calibrator does not have a guard connection and has a floating output, connect the negative
output to AI GND. If the calibrator output is not floating, do not make any other connections.
For more information, refer to the user documentation for the device you are using. If you are
using the E/M/S Series calibration hardware adapter, connect the device as described in the
E Series Calibration Fixture Installation Guide.
Note
Note (NI USB-6215/6216/6218 Devices) For isolated devices, if the calibrator outputs are
truly floating, the negative output must be connected to a quiet earth ground as well as
AI GND to give the entire system a ground reference.
B/E/M/S/X Series Calibration Procedure
10
ni.com
Table 2. Analog Input Connections
Calibrator
Device
Positive Output*
Negative Output*
Guard Connection†
B/E/M/X Series (MIO) ‡
AI 0 (pin 68)**
AI 8 (pin 34)†, **
AI GND (pin 67)†, **
S/X Series
(Simultaneous MIO)††
Connector 0
AI 0 + (pin 68)
AI 0 – (pin 34)†
AI 0 GND (pin 67)†
AI 1 + (pin 33)
AI 1 – (pin 66)†
AI 1 GND (pin 32)†
AI 2 + (pin 65)
AI 2 – (pin 31)†
AI 2 GND (pin 64)†
AI 3 + (pin 30)
AI 3 – (pin 63)†
AI 3 GND (pin 29)†
AI 4 + (pin 28)
AI 4 – (pin 61)†
AI 4 GND (pin 27)†
AI 5 + (pin 60)
AI 5 – (pin 26)†
AI 5 GND (pin 59)†
AI 6 + (pin 25)
AI 6 – (pin 58)†
AI 6 GND (pin 24)†
AI 7 + (pin 57)
AI 7 – (pin 23)†
AI 7 GND (pin 56)†
AI 8 + (pin 68)
AI 8 – (pin 34)†
AI 8 GND (pin 67)†
AI 9 + (pin 33)
AI 9 – (pin 66)†
AI 9 GND (pin 32)†
AI 10 + (pin 65)
AI 10 – (pin 31)†
AI 10 GND (pin 64)†
AI 11 + (pin 30)
AI 11 – (pin 63)†
AI 11 GND (pin 29)†
AI 12 + (pin 28)
AI 12 – (pin 61)†
AI 12 GND (pin 27)†
AI 13 + (pin 60)
AI 13 – (pin 26)†
AI 13 GND (pin 59)†
AI 14 + (pin 25)
AI 14 – (pin 58)†
AI 14 GND (pin 24)†
AI 15 + (pin 57)
AI 15 – (pin 23)†
AI 15 GND (pin 56)†
X Series
(Simultaneous MIO)‡‡
Connector 1
* Pin numbers are given for 68-pin connectors only. If you are using a BNC, DAQPad/USB screw terminal, 34-pin IDC
header, 50-pin IDC header, 37-pin, or 100-pin connector, refer to your device user documentation for signal connection
locations.
† If your calibrator has a guard connection, connect that terminal to AI GND. If your calibrator does not have a guard
connection and has a floating output, connect the negative output to AI GND. If the calibrator output is not floating,
do not make any other connections. For more information, refer to the user documentation for the device you are using.
‡ NI
632x/634x/6351/6353/6361/6363 X Series MIO devices.
** You
must perform verification on all ranges of one analog input channel in differential mode. (Optional) Then, perform
verification on one range of all remaining analog input channels in differential mode to verify that the device mux and analog
input lines are operating properly. Refer to your device user documentation for signal connection locations.
††
NI 6356/6358/6366/6368 X Series simultaneous MIO devices.
‡‡
NI 6358/6368 X Series simultaneous MIO devices.
© National Instruments Corporation
11
B/E/M/S/X Series Calibration Procedure
2.
Choose the table from the Test Limits section that corresponds with the
device you are verifying. This table shows all acceptable settings for
the device type. NI recommends that you verify all ranges, although
you may want to save time by checking only the ranges used in your
application.
3.
Set the calibrator voltage to the test value indicated in the device table.
4.
Create a task using DAQmxCreateTask.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCreateTask with the following
parameters:
LabVIEW does not require this step.
5.
taskName: AIVerificationTask
taskHandle: &taskHandle
Add a channel to the task using the DAQmx Create Virtual Channel VI
and configure the channel. Use the tables in the Test Limits section to
determine the minimum and maximum values for your device.
Throughout the procedure, refer to the NI-DAQmx function call parameters for the
LabVIEW input values.
Note
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCreateAIVoltageChan with the
following parameters:
taskHandle: taskHandle
physicalChannel: dev1/ai0
nameToAssignToChannel:
myVoltageChannel
terminalConfig: DAQmx_Val_Cfg_Default
minVal: –10.0
maxVal: 10.0
units: DAQmx_Val_Volts
customScaleName: NULL
B/E/M/S/X Series Calibration Procedure
12
ni.com
6.
(NI 628x Devices) Configure the lowpass filter by setting the
AI.Lowpass.Enable property node to True.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxSetChanAttribute with the
following parameters:
taskHandle: taskHandle
Channel: ""
Attribute: DAQmx_AI_Lowpass_Enable
Value: 0 (filter off) or 1 (filter on)
7.
Configure timing for the voltage acquisition using the DAQmx
Timing VI.
(NI 6011E [PCI-MIO-16XE-50] and NI 6115/6120 Devices) Use 20000.0 for
rate and 20000 for sampsPerChan.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCfgSampClkTiming with the
following parameters:
taskHandle: taskHandle
source: NULL
rate: 100000.0 or 20000.0
activeEdge: DAQmx_Val_Rising
sampleMode: DAQmx_Val_FiniteSamps
sampsPerChan: 10000 or 20000
8.
(NI 6023E/6024E/6025E/6040E/6062E Devices) For 12-bit E Series devices,
configure dither to be on by setting the AI.Dither.Enable property node
to True.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxSetAIDitherEnable with the
following parameters:
taskHandle: taskHandle
channel []: MyVoltageChannel
bool32: TRUE
© National Instruments Corporation
13
B/E/M/S/X Series Calibration Procedure
9.
Start the acquisition using the DAQmx Start Task VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxStartTask with the following
parameter:
taskHandle: taskHandle
10. Acquire 10,000 points of voltage data using the DAQmx Read VI.
(NI 6011E [PCI-MIO-16XE-50] and NI 6115/6120 Devices) Acquire
20,000 points of voltage data using the DAQmx Read VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxReadAnalogF64 with the following
parameters:
taskHandle: taskHandle
numSampsPerChan: –1
timeout: 10.0
fillMode: DAQmx_Val_GroupByChannel
readArray: data
arraySizeInSamples: 10000 or 20000
sampsPerChanRead: &read
reserved: NULL
11. Average the voltage values that you acquired. Compare the resulting
average to the upper and lower limits listed in the table in the Test
Limits section. If the result is between these values, the device passes
the test.
12. Clear the acquisition using the DAQmx Clear Task VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxClearTask with the following
parameter:
taskHandle: taskHandle
13. (B/E/M/X Series [MIO] Devices) Repeat steps 4 through 12 until all values
have been verified on NI 60xx/60xxE/62xx/632x/634x/6351/6353/
6361/6363 devices.
(S/X Series [Simultaneous MIO] Devices) Repeat steps 4 through 12 for
all channels and all values on NI 61xx/6356/6358/6366/6368 devices.
B/E/M/S/X Series Calibration Procedure
14
ni.com
14. Disconnect the calibrator from the device.
You have finished verifying the analog input levels on your device.
Analog Output Verification
This procedure checks the performance of all analog output channels. Most
B/E/M/S/X Series devices have two analog outputs, AO 0 and AO 1. Some
M/X Series devices have four analog outputs, two on each connector. Skip
this step if the device you are calibrating does not have analog output
circuitry.
The test limits used in this document assume a maximum temperature drift of
±10 °C from the last external calibration, and a maximum temperature drift of ±1 °C from
the last self-calibration. Refer to the Calibration Procedure section for more information
and instructions on reading your device temperature and comparing it against the device
temperature during the last external calibration.
Note
Complete the following steps to check analog output measurements.
1.
Connect your DMM to AO 0 as shown in Table 3.
Note (NI USB-6215/6216/6218 Devices) For isolated devices, you must also connect
AO GND to a quiet earth ground reference or the ground reference of the DMM.
Table 3. Analog Output Connections
DMM
Analog Output
Positive Input*
Negative Input*
AO 0
Connector 0, AO 0 (pin 22)
Connector 0, AO GND (pin 55)
AO 1
Connector 0, AO 1 (pin 21)
Connector 0, AO GND (pin 55)
AO 2
Connector 1, AO 2 (pin 22)
Connector 1, AO GND (pin 55)
AO 3
Connector 1, AO 3 (pin 21)
Connector 1, AO GND (pin 55)
* Pin numbers are given for 68-pin connectors only. If you are using a BNC, DAQPad/USB screw terminal, 34-pin IDC
header, 50-pin IDC header, 37-pin, or 100-pin connector, refer to your device user documentation for signal connection
locations.
2.
© National Instruments Corporation
Choose the table from the Test Limits section that corresponds with the
device you are verifying. This table shows all acceptable settings for
the device. NI recommends that you verify all ranges, although you
may want to save time by checking only the ranges used in your
application.
15
B/E/M/S/X Series Calibration Procedure
3.
Create a task using DAQmxCreateTask.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCreateTask with the following
parameters:
LabVIEW does not require this step.
4.
taskName: MyAOVoltageTask
taskHandle: &taskHandle
Add an AO voltage task using the DAQmx Create Virtual Channel VI
and configure the channel, AO 0. Use the tables in the Test Limits
section to determine the minimum and maximum values for your
device.
Throughout the procedure, refer to the NI-DAQmx function call parameters for the
LabVIEW input values.
Note
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCreateAOVoltageChan with the
following parameters:
taskHandle: taskHandle
physicalChannel: dev1/ao0
nameToAssignToChannel:
AOVoltageChannel
minVal: –10.0
maxVal: 10.0
units: DAQmx_Val_Volts
customScaleName: NULL
5.
Start the generation using the DAQmx Start Task VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxStartTask with the following
parameter:
taskHandle: taskHandle
B/E/M/S/X Series Calibration Procedure
16
ni.com
6.
Write a voltage to the AO channel using the DAQmx Write VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxWriteAnalogF64 with the
following parameters:
taskHandle: taskHandle
numSampsPerChan: 1
autoStart: 1
timeout: 10.0
dataLayout: DAQmx_Val_GroupByChannel
writeArray: &data
sampsPerChanWritten: &samplesWritten
reserved: NULL
7.
Compare the resulting value shown by the DMM to the upper and
lower limits in the table in the Test Limits section. If the value is
between these limits, the device passes the test.
8.
Clear the acquisition using the DAQmx Clear Task VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxClearTask with the following
parameter:
taskHandle: taskHandle
9.
Repeat steps 3 through 8 until all values have been tested.
10. Disconnect the DMM from AO 0, and reconnect it to AO 1, making the
connections shown in Table 3.
11. Repeat steps 3 through 10 for all AO channels on the device.
12. Disconnect your DMM from the device.
You have finished verifying the analog output levels on your device.
© National Instruments Corporation
17
B/E/M/S/X Series Calibration Procedure
Counter Verification
This procedure verifies the performance of the counter. B/E/M/S/X Series
devices have only one timebase to verify, so only Counter 0 needs to be
checked. It is not possible to adjust this timebase, so only verification can
be performed.
The test limits used in this document assume a maximum temperature drift of
±10 °C from the last external calibration, and a maximum temperature drift of ±1 °C from
the last self-calibration. Refer to the Calibration Procedure section for more information
and instructions on reading your device temperature and comparing it against the device
temperature during the last external calibration.
Note
Complete the following steps to perform checks on the counter.
1.
Connect your counter positive input to CTR 0 OUT (pin 2) and your
counter negative input to D GND (pin 35).1
2.
Create a task using DAQmxCreateTask.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCreateTask with the following
parameters:
LabVIEW does not require this step.
1
taskName: MyCounterOutputTask
taskHandle: &taskHandle
Pin numbers are given for 68-pin connectors only. If you are using a BNC, DAQPad/USB screw terminal, 34-pin IDC header,
50-pin IDC header, 37-pin, or 100-pin connector, refer to your device user documentation for signal connection locations.
B/E/M/S/X Series Calibration Procedure
18
ni.com
3.
Add a counter output channel to the task using the DAQmx Create
Virtual Channel VI and configure the channel.
Throughout the procedure, refer to the NI-DAQmx function call parameters for the
LabVIEW input values.
Note
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCreateCOPulseChanFreq with
the following parameters:
taskHandle: taskHandle
counter: dev1/ctr0
nameToAssignToChannel:
CounterOutputChannel
units: DAQmx_Val_Hz
idleState: DAQmx_Val_Low
initialDelay: 0.0
freq: 5000000.0
dutyCycle: .5
4.
Configure the counter for continuous square wave generation using the
DAQmx Timing VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCfgImplicitTiming with the
following parameters:
taskHandle: taskHandle
sampleMode: DAQmx_Val_ContSamps
sampsPerChan: 10000
5.
Start the generation of a square wave using the DAQmx Start Task VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxStartTask with the following
parameter:
taskHandle: taskHandle
The device generates a 5 MHz square wave when the VI completes
execution.
© National Instruments Corporation
19
B/E/M/S/X Series Calibration Procedure
6.
Configure the counter to measure frequency and use a 1 MΩ
impedance.
7.
Take a measurement of the square wave.
8.
Compare the value read by your counter to the test limits shown on the
device table in the Test Limits section. If the value falls between these
limits, the device passes the test.
9.
Stop the generation using the DAQmx Stop Task VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxStopTask with the following
parameter:
taskHandle: taskHandle
10. Clear the generation using the DAQmx Clear Task VI.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxClearTask with the following
parameter:
taskHandle: taskHandle
11. Disconnect the counter from your device.
You have verified the counter on your device.
Adjustment Procedure
Use the B/E/M/S/X Series adjustment procedure to adjust the analog input
and output calibration constants. At the end of each calibration procedure,
these new constants are stored in the external calibration area of the
EEPROM. These values are password-protected, which prevents the
accidental access or modification of any calibration constants adjusted
by the metrology laboratory. The default password is NI.
B/E/M/S/X Series Calibration Procedure
20
ni.com
Complete the following steps to perform device adjustment with a
calibrator:
1.
Connect the calibrator to the device. Refer to Table 4 to determine
connections between the device and the calibrator. The calibrator
connections depend on the resolution of the device you are calibrating.
If you are using the E/M/S Series calibration hardware adapter, connect the device
as described in the E Series Calibration Fixture Installation Guide.
Note
Table 4. Calibrator Connections
Calibrator
Positive
Output*
Negative
Output*
Guard
Connection†
12-Bit E Series
AI 8
(pin 34)
AI SENSE
(pin 62)†
AI GND
(pin 67)†
16-Bit E Series,
M/X Series (MIO)‡
AI 0
(pin 68)
AI 8
(pin 34)†
AI GND
(pin 67)†
—
S/X Series
(Simultaneous MIO)**
AI 0 +
(pin 68)
AI 0 –
(pin 34)†
AI 0 GND
(pin 67)†
—
Device
Additional
Connections
Connect AO 0
(pin 22) line to
AI 0 (pin 68)
* Pin numbers are given for 68-pin connectors only. If you are using a BNC, DAQPad/USB screw terminal, 34-pin IDC
header, 50-pin IDC header, 37-pin, or 100-pin connector, refer to your device user documentation for signal connection
locations.
† If your calibrator does not have a guard connection and has a floating output, connect the negative output to AI GND. If the
calibrator output is not floating, do not make any other connections. For more information, refer to your DAQ device user
documentation.
‡
NI 632x/634x/6351/6353/6361/6363 X Series MIO devices.
**
NI 6356/6358/6366/6368 X Series simultaneous MIO devices.
2.
Set your calibrator to output a voltage of 7.5 V.
(NI 6010 Devices) Set your calibrator to output a voltage of 3.75 V.
(NI 6115/6120 Devices) Set your calibrator to output a voltage of 5.0 V.
(NI 6143 Devices) Set your calibrator to output a voltage of 4.5 V.
© National Instruments Corporation
21
B/E/M/S/X Series Calibration Procedure
3.
Open a calibration session on your device using the DAQmx Initialize
External Calibration VI. The default password is NI.
Throughout the procedure, refer to the NI-DAQmx function call parameters for the
LabVIEW input values.
Note
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxInitExtCal with the following
parameters:
deviceName: dev1
password: NI
calHandle: &calHandle
4.
Perform an external calibration adjustment using the DAQmx Adjust
Y-Series Calibration VI, where Y is the letter of the device series.
Note (NI 6010 Devices) Use the DAQmx Adjust M-Series Calibration VI
(DAQmxMSeriesCalAdjust).
Note (NI 6013/6014/6015/6016 Devices) Use the DAQmx Adjust E-Series Calibration VI
(DAQmxESeriesCalAdjust).
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxYSeriesCalAdjust with the
following parameters:
calHandle: calHandle
referenceVoltage: 7.5, 3.75, 5, or 4.5
(based on calibrator output from step 2)
B/E/M/S/X Series Calibration Procedure
22
ni.com
5.
Note
Save the adjustment to the EEPROM, using the DAQmx Close
External Calibration VI. This VI also saves the date, time, and
temperature of the adjustment to the onboard memory.
If an error occurs during adjustment, no constants will be written to the EEPROM.
LabVIEW Block Diagram
NI-DAQmx Function Call
Call DAQmxCloseExtCal with the following
parameters:
calHandle: calHandle
action: DAQmx_Val_Action_Commit
6.
Disconnect the calibrator from the device.
The device is now calibrated with respect to your external source.
After calibrating the device, you may want to verify the analog input and
output operation. To do this, repeat the Verification Procedure section.
Test Limits
The tables in this section list the specifications for B/E/M/S/X Series
devices. The specifications are divided into analog input, analog output,
and counter/timer tables of values.
The following definitions describe how to use the information from the
tables in this section:
•
Range—Range refers to the maximum allowable voltage range of an
input or output signal.
•
Test Point—The Test Point is the voltage value that is input or
output for verification purposes. This value is broken down into
two columns—Location and Value. Location refers to where the test
value fits within the test range. Value refers to the voltage value to be
verified and is in volts. Pos FS stands for positive full-scale and
Neg FS stands for negative full-scale.
© National Instruments Corporation
23
B/E/M/S/X Series Calibration Procedure
•
Note
24-Hour Limits—The values shown in the 24-hour tables are the valid
specifications when a device has been calibrated with an external
source. The 24-Hour Limits column contains the Upper Limits and
Lower Limits for the test point value. That is, when the device is within
its 24-hour calibration interval, the test point value should fall between
the upper and lower limit values. Upper and lower limits are expressed
in volts or amps, depending on the device.
Some devices only have 1-year limits specifications.
•
1-Year Limits—The 1-year limits display the specifications that the
devices should meet if it has been one year between calibrations. The
1-Year Limits column contains the Upper Limits and Lower Limits for
the test point value. That is, when the device is within its one year
calibration interval, the test point value should fall between the upper
and lower limit values. Upper and lower limits are expressed in volts
or amps, depending on the device.
Note (NI 6122/6123/625x/628x/6351/6353/6361/6363 Devices)
NI 6122/6123/625x/628x/6351/6353/6361/6363 devices have 2-year and 24-hour
calibration intervals.
•
B/E/M/S/X Series Calibration Procedure
Counters—It is not possible to adjust the resolution of the counters.
Therefore, these values do not have a 1-year or 24-hour calibration
period. However, the test point and upper and lower limits are provided
for verification purposes.
24
ni.com
© National Instruments Corporation
B Series Test Limits
NI 6010—16-Bit Resolution
Tables 5 through 7 include values for the PCI-6010.
Table 5. NI 6010 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
25
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–5
5
Pos FS
4.990000
4.986551
4.993449
4.984929
4.995071
–5
5
0.000000
0.000000
–0.002327
0.002327
–0.002327
0.002327
–5
5
Neg FS
–4.990000
–4.993449
–4.986551
–4.995071
–4.984929
–1
1
Pos FS
0.998000
0.997214
0.998786
0.996889
0.999111
–1
1
0.000000
0.000000
–0.000508
0.000508
–0.000508
0.000508
–1
1
Neg FS
–0.998000
–0.998786
–0.997214
–0.999111
–0.996889
–0.2
0.2
Pos FS
0.199600
0.199382
0.199818
0.199317
0.199883
–0.2
0.2
0.000000
0.000000
–0.000156
0.000156
–0.000156
0.000156
–0.2
0.2
Neg FS
–0.199600
–0.199818
–0.199382
–0.199883
–0.199317
B/E/M/S/X Series Calibration Procedure
Table 6. NI 6010 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–5
5
Pos FS
4.990000
4.986244
4.993756
4.984623
4.995377
–5
5
0.000000
0.000000
–0.001615
0.001615
–0.001615
0.001615
–5
5
Neg FS
–4.990000
–4.993756
–4.986244
–4.995377
–4.984623
Table 7. NI 6010 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
26
ni.com
© National Instruments Corporation
NI 6013/6014/6015/6016—16-Bit Resolution
Tables 8 through 10 include values for the PCI-6013 (analog input only), PCI-6014, DAQPad-6015, and
DAQPad-6016.
Table 8. NI 6013/6014/6015/6016 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
27
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8
9.791572
9.808428
9.791160
9.808840
–10
10
0
0
–0.001980
0.001980
–0.001980
0.001980
–10
10
Neg FS
–9.8
–9.808428
–9.791572
–9.808840
–9.791160
–5
5
Pos FS
4.9
4.898225
4.901776
4.898019
4.901981
–5
5
0
0
–0.001001
0.001001
–0.001001
0.001001
–5
5
Neg FS
–4.9
–4.901776
–4.898225
–4.901981
–4.898019
–0.5
0.5
Pos FS
0.49
0.489557
0.490443
0.489536
0.490464
–0.5
0.5
0
0
–0.000121
0.000121
–0.000121
0.000121
–0.5
0.5
Neg FS
–0.49
–0.490443
–0.489557
–0.490464
–0.489536
–0.05
0.05
Pos FS
0.049
0.048933
0.049067
0.048931
0.049069
–0.05
0.05
0
0
–0.000034
0.000034
–0.000034
0.000034
–0.05
0.05
Neg FS
–0.049
–0.049067
–0.048933
–0.049069
–0.048931
B/E/M/S/X Series Calibration Procedure
Table 9. NI 6014/6015/6016 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8
9.795069
9.804931
9.794236
9.805764
–10
10
0
0
–0.002461
0.002461
–0.002461
0.002461
–10
10
Neg FS
–9.8
–9.804931
–9.795069
–9.805764
–9.794236
Table 10. NI 6013/6014/6015/6016 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
28
ni.com
© National Instruments Corporation
E Series Test Limits
NI 6011E—16-Bit Resolution
Tables 11 through 13 include values for the NI 6011E (PCI-MIO-16XE-50).
Table 11. NI 6011E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
29
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.98
9.978978
9.981022
9.978559
9.981441
–10
10
0
0
–0.000443
0.000443
–0.000443
0.000443
–10
10
Neg FS
–9.98
–9.981022
–9.978978
–9.981441
–9.978559
–5
5
Pos FS
4.99
4.988739
4.991261
4.988529
4.991471
–5
5
0
0
–0.000224
0.000224
–0.000224
0.000224
–5
5
Neg FS
–4.99
–4.991261
–4.988739
–4.991471
–4.988529
–1
1
Pos FS
0.998
0.997745
0.998255
0.997703
0.998297
–1
1
0
0
–0.000048
0.000048
–0.000048
0.000048
–1
1
Neg FS
–0.998
–0.998255
–0.997745
–0.998297
–0.997703
–0.1
0.1
Pos FS
0.0998
0.099751
0.099849
0.099746
0.099854
–0.1
0.1
0
0
–0.000009
0.000009
–0.000009
0.000009
–0.1
0.1
Neg FS
–0.0998
–0.099849
–0.099751
–0.099854
–0.099746
0
10
Pos FS
9.98
9.979154
9.980846
9.978735
9.981266
0
10
0
0.02
0.019731
0.020269
0.019731
0.020270
0
5
Pos FS
4.99
4.988826
4.991174
4.988617
4.991383
B/E/M/S/X Series Calibration Procedure
Table 11. NI 6011E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
0
5
0
0.01
0.009862
0.010138
0.009862
0.010138
0
1
Pos FS
0.998
0.997762
0.998238
0.997720
0.998280
0
1
0
0.002
0.001969
0.002031
0.001969
0.002031
0
0.1
Pos FS
0.0998
0.099752
0.099848
0.099748
0.099852
0
0.1
0
0.0002
0.000193
0.000207
0.000193
0.000207
Table 12. NI 6011E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
30
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.9800000
9.973195
9.986805
9.972796
9.987204
–10
10
0
0.0000000
–0.005408
0.005408
–0.005408
0.005408
–10
10
Neg FS
–9.9800000
–9.986805
–9.973195
–9.987204
–9.972796
0
10
Pos FS
9.9800000
9.975637
9.984363
9.975238
9.984762
0
10
0
0.0200000
0.017031
0.022969
0.017030
0.022970
Table 13. NI 6011E Counter Values
ni.com
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
© National Instruments Corporation
NI 6023E/6024E/6025E—12-Bit Resolution
Tables 14 through 16 include values for the PCI-6023E (analog input only), PCI-6024E, PCI-6025E,
and PXI-6025E.
Table 14. NI 6023E/6024E/6025E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
31
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.800
9.7841
9.8159
9.7837
9.8163
–10
10
0
0.000
–0.0074
0.0074
–0.0074
0.0074
–10
10
Neg FS
–9.800
–9.8159
–9.7841
–9.8163
–9.7837
–5
5
Pos FS
4.900
4.8950
4.9050
4.8948
4.9052
–5
5
0
0.000
–0.0037
0.0037
–0.0037
0.0037
–5
5
Neg FS
–4.900
–4.9050
–4.8950
–4.9052
–4.8948
–0.5
0.5
Pos FS
0.490
0.48918
0.49082
0.48916
0.49084
–0.5
0.5
0
0.000
–0.00039
0.00039
–0.00039
0.00039
–0.5
0.5
Neg FS
–0.490
–0.49082
–0.48918
–0.49084
–0.48916
–0.05
0.05
Pos FS
0.049
0.048897
0.049103
0.048895
0.049105
–0.05
0.05
0
0.000
–0.000060
0.000060
–0.000060
0.000060
–0.05
0.05
Neg FS
–0.049
–0.049103
–0.048897
–0.049105
–0.048895
B/E/M/S/X Series Calibration Procedure
Table 15. NI 6024E/6025E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.800000
9.792335
9.807665
9.791924
9.808076
–10
10
0
0.0000000
–0.005930
0.005930
–0.005930
0.005930
–10
10
Neg FS
–9.800000
–9.807665
–9.792335
–9.808076
–9.791924
Table 16. NI 6023E/6024E/6025E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
32
ni.com
© National Instruments Corporation
NI DAQCard-6024E—12-Bit Resolution
Tables 17 through 19 include values for the DAQCard-6024E.
Table 17. NI DAQCard-6024E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
33
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.800
9.7816
9.8184
9.7812
9.8188
–10
10
0
0.000
–0.0099
0.0099
–0.0099
0.0099
–10
10
Neg FS
–9.800
–9.8184
–9.7816
–9.8188
–9.7812
–5
5
Pos FS
4.900
4.8937
4.9063
4.8935
4.9065
–5
5
0
0.000
–0.0049
0.0049
–0.0049
0.0049
–5
5
Neg FS
–4.900
–4.9063
–4.8937
–4.9065
–4.8935
–0.5
0.5
Pos FS
0.490
0.48906
0.49094
0.48904
0.49096
–0.5
0.5
0
0.000
–0.00051
0.00051
–0.00051
0.00051
–0.5
0.5
Neg FS
–0.490
–0.49094
–0.48906
–0.49096
–0.48904
–0.05
0.05
Pos FS
0.049
0.048884
0.049116
0.048882
0.049118
–0.05
0.05
0
0.000
–0.000073
0.000073
–0.000073
0.000073
–0.05
0.05
Neg FS
–0.049
–0.049116
–0.048884
–0.049118
–0.048882
B/E/M/S/X Series Calibration Procedure
Table 18. NI DAQCard-6024E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8000000
9.789895
9.810105
9.789484
9.810516
–10
10
0
0.0000000
–0.008370
0.008370
–0.008370
0.008370
–10
10
Neg FS
–9.8000000
–9.810105
–9.789895
–9.810516
–9.789484
Table 19. NI DAQCard-6024E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
34
ni.com
© National Instruments Corporation
NI 6030E/6031E/6032E/6033E—16-Bit Resolution
Tables 20 through 22 include values for the PCI-6030E (PCI-MIO-16XE-10), PXI-6030E, PCI-6031E,
PXI-6031E, PCI-6032E, and PCI-6033E.
Table 20. NI 6030E/6031E/6032E/6033E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
35
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.98
9.979027
9.980973
9.978857
9.981143
–10
10
0
0
–0.000534
0.000534
–0.000534
0.000534
–10
10
Neg FS
–9.98
–9.980973
–9.979027
–9.981143
–9.978857
–5
5
Pos FS
4.99
4.988012
4.991988
4.987928
4.992072
–5
5
0
0
–0.000271
0.000271
–0.000271
0.000271
–5
5
Neg FS
–4.99
–4.991988
–4.988012
–4.992072
–4.987928
–2
2
Pos FS
1.996
1.995200
1.996800
1.995166
1.996834
–2
2
0
0
–0.000113
0.000113
–0.000113
0.000113
–2
2
Neg FS
–1.996
–1.996800
–1.995200
–1.996834
–1.995166
–1
1
Pos FS
0.998
0.997596
0.998404
0.997579
0.998421
–1
1
0
0
–0.000061
0.000061
–0.000061
0.000061
–1
1
Neg FS
–0.998
–0.998404
–0.997596
–0.998421
–0.997579
–0.5
0.5
Pos FS
0.499
0.498794
0.499206
0.498785
0.499215
–0.5
0.5
0
0
–0.000035
0.000035
–0.000035
0.000035
–0.5
0.5
Neg FS
–0.499
–0.499206
–0.498794
–0.499215
–0.498785
B/E/M/S/X Series Calibration Procedure
Table 20. NI 6030E/6031E/6032E/6033E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
36
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.2
0.2
Pos FS
0.1996
0.199502
0.199698
0.199499
0.199701
–0.2
0.2
0
0
–0.000019
0.000019
–0.000019
0.000019
–0.2
0.2
Neg FS
–0.1996
–0.199698
–0.199502
–0.199701
–0.199499
–0.1
0.1
Pos FS
0.0998
0.099741
0.099859
0.099739
0.099861
–0.1
0.1
0
0
–0.000015
0.000015
–0.000015
0.000015
–0.1
0.1
Neg FS
–0.0998
–0.099859
–0.099741
–0.099861
–0.099739
0
10
Pos FS
9.98
9.979198
9.980802
9.979028
9.980972
0
10
0
0.02
0.019636
0.020364
0.019636
0.020364
0
5
Pos FS
4.99
4.988098
4.991902
4.988013
4.991987
0
5
0
0.01
0.009811
0.010189
0.009811
0.010189
0
2
Pos FS
1.996
1.995234
1.996766
1.995200
1.996800
0
2
0
0.004
0.003920
0.004080
0.003920
0.004080
0
1
Pos FS
0.998
0.997613
0.998387
0.997596
0.998404
0
1
0
0.002
0.001956
0.002044
0.001956
0.002044
0
0.5
Pos FS
0.499
0.498802
0.499198
0.498793
0.499207
0
0.5
0
0.001
0.000973
0.001027
0.000973
0.001027
0
0.2
Pos FS
0.1996
0.199505
0.199695
0.199502
0.199698
0
0.2
0
0.0004
0.000384
0.000416
0.000384
0.000416
© National Instruments Corporation
Table 20. NI 6030E/6031E/6032E/6033E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
0
0.1
Pos FS
0.0998
0.099743
0.099857
0.099741
0.099859
0
0.1
0
0.0002
0.000187
0.000213
0.000187
0.000213
Table 21. NI 6030E/6031E/6032E/6033E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
37
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.9800000
9.978738
9.981262
9.978568
9.981432
–10
10
0
0.0000000
–0.000813
0.000813
–0.000813
0.000813
–10
10
Neg FS
–9.9800000
–9.981262
–9.978738
–9.981432
–9.978568
0
10
Pos FS
9.9800000
9.978967
9.981033
9.978797
9.981203
0
10
0
0.0200000
0.019415
0.020585
0.019415
0.020585
B/E/M/S/X Series Calibration Procedure
Table 22. NI 6030E/6031E/6032E/6033E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
B/E/M/S/X Series Calibration Procedure
NI 6034E/6035E/6036E—16-Bit Resolution
Tables 23 through 26 include values for the PCI-6034E (analog input only), PCI-6035E, and PCI-6036E.
Table 23. NI 6034E/6035E/6036E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
38
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.900
9.8929
9.9071
9.8925
9.9075
–10
10
0
0.000
–0.0017
0.0017
–0.0017
0.0017
–10
10
Neg FS
–9.900
–9.9071
–9.8929
–9.9075
–9.8925
–5
5
Pos FS
4.950
4.9484
4.9516
4.9482
4.9518
–5
5
0
0.000
–0.0009
0.0009
–0.0009
0.0009
–5
5
Neg FS
–4.950
–4.9516
–4.9484
–4.9518
–4.9482
–0.5
0.5
Pos FS
0.495
0.49462
0.49538
0.49460
0.49540
–0.5
0.5
0
0.000
–0.00011
0.00011
–0.00011
0.00011
–0.5
0.5
Neg FS
–0.495
–0.49538
–0.49462
–0.49540
–0.49460
–0.05
0.05
Pos FS
0.0495
0.049441
0.049559
0.049439
0.049561
–0.05
0.05
0
0.000
–0.000032
0.000032
–0.000032
0.000032
–0.05
0.05
Neg FS
–0.0495
–0.049559
–0.049441
–0.049561
–0.049439
ni.com
© National Instruments Corporation
Table 24. NI 6035E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.9000000
9.892315
9.907685
9.891899
9.908101
–10
10
0
0.0000000
–0.005933
0.005933
–0.005933
0.005933
–10
10
Neg FS
–9.9000000
–9.907685
–9.892315
–9.908101
–9.891899
Table 25. NI 6036E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
39
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.9000000
9.898009
9.901991
9.897603
9.902397
–10
10
0
0.0000000
–0.001100
0.001100
–0.001100
0.001100
–10
10
Neg FS
–9.9000000
–9.901991
–9.898009
–9.902397
–9.897603
Table 26. NI 6034E/6035E/6036E Counter Values
B/E/M/S/X Series Calibration Procedure
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
B/E/M/S/X Series Calibration Procedure
NI DAQCard-6036E—16-Bit Resolution
Tables 27 through 29 include values for the DAQCard-6036E.
Table 27. NI DAQCard-6036E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
40
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.900
9.8918
9.9082
9.8914
9.9086
–10
10
0
0.000
–0.0027
0.0027
–0.0027
0.0027
–10
10
Neg FS
–9.900
–9.9082
–9.8918
–9.9086
–9.8914
–5
5
Pos FS
4.950
4.9479
4.9521
4.9477
4.9523
–5
5
0
0.000
–0.0014
0.0014
–0.0014
0.0014
–5
5
Neg FS
–4.950
–4.9521
–4.9479
–4.9523
–4.9477
–0.5
0.5
Pos FS
0.495
0.49457
0.49543
0.49455
0.49545
–0.5
0.5
0
0.000
–0.00016
0.00016
–0.00016
0.00016
–0.5
0.5
Neg FS
–0.495
–0.49543
–0.49457
–0.49545
–0.49455
–0.05
0.05
Pos FS
0.0495
0.049436
0.049564
0.049434
0.049566
–0.05
0.05
0
0.000
–0.000037
0.000037
–0.000037
0.000037
–0.05
0.05
Neg FS
–0.0495
–0.049564
–0.049436
–0.049566
–0.049434
ni.com
© National Instruments Corporation
Table 28. NI DAQCard-6036E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.9000000
9.897879
9.902121
9.897463
9.902537
–10
10
0
0.0000000
–0.001220
0.001220
–0.001220
0.001220
–10
10
Neg FS
–9.9000000
–9.902121
–9.897879
–9.902537
–9.897463
Table 29. NI DAQCard-6036E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
41
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
NI 6040E—12-Bit Resolution
Tables 30 through 32 include values for the PCI-MIO-16E-4 and PXI-6040E.
Table 30. NI 6040E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
42
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.96507
9.99493
9.96465
9.99535
–10
10
0
0.000000
–0.00823
0.00823
–0.00823
0.00823
–10
10
Neg FS
–9.980000
–9.99493
–9.96507
–9.99535
–9.96465
–5
5
Pos FS
4.99
4.98452
4.99548
4.98431
4.99569
–5
5
0
0.000000
–0.00412
0.00412
–0.00412
0.00412
–5
5
Neg FS
–4.99
–4.99548
–4.98452
–4.99569
–4.98431
–2.5
2.5
Pos FS
2.495000
2.49125
2.49875
2.49115
2.49885
–2.5
2.5
0
0.000000
–0.00207
0.00207
–0.00207
0.00207
–2.5
2.5
Neg FS
–2.495000
–2.49875
–2.49125
–2.49885
–2.49115
–1
1
Pos FS
0.998000
0.99649
0.99951
0.99645
0.99955
–1
1
0
0.000000
–0.00084
0.00084
–0.00084
0.00084
–1
1
Neg FS
–0.998000
–0.99951
–0.99649
–0.99955
0.99645
–0.5
0.5
Pos FS
0.499000
0.49823
0.49977
0.49821
0.49979
–0.5
0.5
0
0.000000
–0.00043
0.00043
–0.00043
0.00043
–0.5
0.5
Neg FS
–0.499000
–0.49977
–0.49823
–0.49979
–0.49821
–0.25
0.25
Pos FS
0.249500
0.24911
0.24989
0.24910
0.24990
© National Instruments Corporation
Table 30. NI 6040E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
43
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.25
0.25
0
0.000000
–0.00023
0.00023
–0.00023
0.00023
–0.25
0.25
Neg FS
–0.249500
–0.24989
–0.24911
–0.24990
–0.24910
–0.1
0.1
Pos FS
0.099800
0.09963
0.09997
0.09962
0.09998
–0.1
0.1
0
0.000000
–0.00011
0.00011
–0.00011
0.00011
–0.1
0.1
Neg FS
–0.099800
–0.09997
–0.09963
–0.09998
–0.09962
–0.05
0.05
Pos FS
0.049900
0.04980
0.05000
0.04980
0.05000
–0.05
0.05
0
0.000000
–0.00006
0.00006
–0.00006
0.00006
–0.05
0.05
Neg FS
–0.049900
–0.05000
–0.04980
–0.05000
–0.04980
0
10
Pos FS
9.980000
9.97316
9.98684
9.97274
9.98726
0
10
0
0.020000
0.01587
0.02413
0.01587
0.02413
0
5
Pos FS
4.990000
4.98458
4.99542
4.98437
4.99563
0
5
0
0.010000
0.00792
0.01208
0.00792
0.01208
0
2
Pos FS
1.996000
1.99382
1.99818
1.99373
1.99827
0
2
0
0.004000
0.00316
0.00484
0.00316
0.00484
0
1
Pos FS
0.998000
0.99690
0.99910
0.99686
0.99914
0
1
0
0.002000
0.00157
0.00243
0.00157
0.00243
0
0.5
Pos FS
0.499000
0.49844
0.49956
0.49842
0.49958
0
0.5
0
0.001000
0.00077
0.00123
0.00077
0.00123
B/E/M/S/X Series Calibration Procedure
Table 30. NI 6040E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
0
0.2
Pos FS
0.199600
0.199361
0.199839
0.199352
0.199848
0
0.2
0
0.000400
0.000295
0.000505
0.000295
0.000505
0
0.1
Pos FS
0.099800
0.099669
0.099931
0.099665
0.099935
0
0.01
0
0.000200
0.000136
0.000264
0.000136
0.000264
Table 31. NI 6040E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
44
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.98
9.972304
9.987696
9.971884
9.988116
–10
10
0
0
–0.005930
0.005930
–0.005930
0.005930
–10
10
Neg FS
–9.98
–9.987696
–9.972304
–9.988116
–9.971884
0
10
Pos FS
9.98
9.974744
9.985256
9.974324
9.985676
0
10
0
0.02
0.016506
0.023494
0.016506
0.023494
Table 32. NI 6040E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
ni.com
© National Instruments Corporation
NI 6052E—16-Bit Resolution
Tables 33 through 35 include values for the PCI-6052E and PXI-6052E.
Table 33. NI 6052E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
45
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.800
9.7955
9.8045
9.7953
9.8047
–10
10
0
0.00
–0.0010
0.0010
–0.0010
0.0010
–10
10
Neg FS
–9.800
–9.8045
–9.7955
–9.8047
–9.7953
–5
5
Pos FS
4.900
4.8992
4.9008
4.8991
4.9009
–5
5
0
0.000
–0.0005
0.0005
–0.0005
0.0005
–5
5
Neg FS
–4.900
–4.9008
–4.8992
–4.9009
–4.8991
–2.5
2.5
Pos FS
2.450
2.44887
2.45113
2.44883
2.45117
–2.5
2.5
0
0.000
–0.00026
0.00026
–0.00026
0.00026
–2.5
2.5
Neg FS
–2.450
–2.45113
–2.44887
–2.45117
–2.44883
–1
1
Pos FS
0.980
0.9795
0.9805
0.9795
0.9805
–1
1
0
0.000
–0.0001
0.0001
–0.0001
0.0001
–1
1
Neg FS
–0.980
–0.9805
–0.9795
–0.9805
–0.9795
–0.5
0.5
Pos FS
0.490
0.48977
0.49023
0.48976
0.49024
–0.5
0.5
0
0.000
–0.00006
0.00006
–0.00006
0.00006
–0.5
0.5
Neg FS
–0.490
–0.49023
–0.48977
–0.49024
–0.48976
–0.25
0.25
Pos FS
0.245
0.2449
0.2451
0.2449
0.2451
B/E/M/S/X Series Calibration Procedure
Table 33. NI 6052E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
46
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.25
0.25
0
0.000
–0.0000316
0.0000316
–0.0000316
0.0000316
–0.25
0.25
Neg FS
–0.245
–0.2451
–0.2449
–0.2451
–0.2449
–0.1
0.1
Pos FS
0.098
0.09794
0.09806
0.09794
0.09806
–0.1
0.1
0
0.000
–0.0000165
0.0000165
–0.0000165
0.0000165
–0.1
0.1
Neg FS
–0.098
–0.09806
–0.09794
–0.09806
–0.09794
–0.05
0.05
Pos FS
0.049
0.048966
0.049034
0.048965
0.049035
–0.05
0.05
0
0.000
–0.000012
0.000012
–0.000012
0.000012
–0.05
0.05
Neg FS
–0.049
–0.049034
–0.048966
–0.049035
–0.048965
0
10
Pos FS
9.8
9.798951
9.801049
9.798785
9.801215
0
10
0
0.0098
0.009280
0.010320
0.009280
0.010320
0
5
Pos FS
4.9
4.898003
4.901997
4.897919
4.902081
0
5
0
0.0098
0.009534
0.010066
0.009534
0.010066
0
2
Pos FS
1.96
1.959198
1.960802
1.959165
1.960835
0
2
0
0.0098
0.009689
0.009911
0.009688
0.009912
0
1
Pos FS
0.98
0.979547
0.980453
0.979530
0.980470
0
1
0
0.0098
0.009739
0.009861
0.009739
0.009861
0
0.5
Pos FS
0.49
0.489746
0.490254
0.489738
0.490262
0
0.5
0
0.0098
0.009764
0.009836
0.009764
0.009836
© National Instruments Corporation
Table 33. NI 6052E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
0
0.2
Pos FS
0.196
0.195895
0.196105
0.195891
0.196109
0
0.2
0
0.0098
0.009779
0.009821
0.009779
0.009821
0
0.1
Pos FS
0.098
0.097944
0.098056
0.097942
0.098058
0
0.1
0
0.0098
0.009784
0.009816
0.009784
0.009816
Table 34. NI 6052E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
47
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8000000
9.798771
9.801229
9.798604
9.801396
–10
10
0
0.0000000
–0.000798
0.000798
–0.000798
0.000798
–10
10
Neg FS
–9.8000000
–9.801229
–9.798771
–9.801396
–9.798604
0
10
Pos FS
9.8000000
9.799000
9.801000
9.798833
9.801167
0
10
0
0.0098000
0.009231
0.010369
0.009230
0.010370
Table 35. NI 6052E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
B/E/M/S/X Series Calibration Procedure
NI DAQCard-6062E—12-Bit Resolution
Tables 36 through 38 include values for the DAQCard-6062E.
Table 36. NI DAQCard-6062E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
48
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.80000
9.7802
9.8198
9.7797
9.8203
–10
10
0
0.000000
–0.0108
0.0108
–0.0108
0.0108
–10
10
Neg FS
–9.80000
–9.8198
–9.7802
–9.8203
–9.7797
–5
5
Pos FS
4.900000
4.9826
4.9074
4.8924
4.9076
–5
5
0
0.000000
–0.0054
0.0054
–0.0054
0.0054
–5
5
Neg FS
–4.900000
–4.9074
–4.8926
–4.9076
–4.8924
–2.5
2.5
Pos FS
2.450000
2.44503
2.45497
2.44492
2.45508
–2.5
2.5
0
0.000000
–0.00271
0.00271
–0.00271
0.00271
–2.5
2.5
Neg FS
–2.450000
–2.45497
–2.44503
–2.45508
–2.44492
–1
1
Pos FS
0.980000
0.977997
0.982003
0.977956
0.982044
–1
1
0
0.000000
–0.001099
0.001099
–0.001099
0.001099
–1
1
Neg FS
–0.980000
–0.982003
–0.977997
–0.982044
–0.977956
–0.5
0.5
Pos FS
0.490000
0.4890
0.4910
0.4890
0.4910
–0.5
0.5
0
0.000000
–0.0006
0.0006
–0.0006
0.0006
–0.5
0.5
Neg FS
–0.490000
–0.49051
–0.48949
–0.49053
–0.48947
–0.25
0.25
Pos FS
0.245000
0.2445
0.2455
0.2445
0.2455
© National Instruments Corporation
Table 36. NI DAQCard-6062E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
49
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.25
0.25
0
0.000000
–0.0003
0.0003
–0.0003
0.0003
–0.25
0.25
Neg FS
–0.245000
–0.2455
–0.2445
–0.2455
–0.2445
–0.1
0.1
Pos FS
0.098000
0.09778
0.09822
0.09777
0.09823
–0.1
0.1
0
0.000000
–0.00013
0.00013
–0.00013
0.00013
–0.1
0.1
Neg FS
–0.098000
–0.09822
–0.09778
–0.09823
–0.09777
–0.05
0.05
Pos FS
0.049000
0.048877
0.049123
0.048875
0.049125
–0.05
0.05
0
0.000000
–0.000078
0.000078
–0.000078
0.000078
–0.05
0.05
Neg FS
–0.049000
–0.049123
–0.048877
–0.049125
–0.048875
0
10
Pos FS
9.800000
9.7907
9.8093
9.7903
9.8097
0
10
0
0.020000
0.0146
0.0254
0.0146
0.0254
0
5
Pos FS
4.900000
4.8928
4.9072
4.8926
4.9074
0
5
0
0.010000
0.0073
0.0127
0.0073
0.0127
0
2
Pos FS
1.996000
1.9571
1.9629
1.9570
1.9630
0
2
0
0.004000
0.0029
0.0051
0.0029
0.0051
0
1
Pos FS
0.980000
0.97854
0.98146
0.97850
0.98150
0
1
0
0.002000
0.00144
0.00256
0.00144
0.00256
0
0.5
Pos FS
0.490000
0.48925
0.49075
0.48923
0.49077
0
0.5
0
0.001000
0.000704
0.001296
0.000704
0.001296
B/E/M/S/X Series Calibration Procedure
Table 36. NI DAQCard-6062E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
0
0.2
Pos FS
0.199600
0.195688
0.196312
0.195680
0.196320
0
0.2
0
0.000400
0.000269
0.000531
0.000269
0.000531
0
0.01
Pos FS
0.099800
0.0978
0.0982
0.0978
0.0982
0
0.01
0
0.000200
0.0001
0.0003
0.0001
0.0003
Table 37. NI DAQCard-6062E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
50
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8000000
9.789895
9.810105
9.789484
9.810516
–10
10
0
0
–0.008370
0.008370
–0.008370
0.008370
–10
10
Neg FS
–9.8000000
–9.810105
–9.789895
–9.810516
–9.789484
Table 38. NI DAQCard-6062E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
ni.com
© National Instruments Corporation
NI 6070E/6071E—12-Bit Resolution
Tables 39 through 41 include values for the PCI-MIO-16E-1, PCI-6070E, PXI-6070E, PCI-6071E, and
PXI-6071E.
Table 39. NI 6070E/6071E Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
51
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.96607
9.99393
9.96565
9.99435
–10
10
0
0.00000
–0.00723
0.00723
–0.00723
0.00723
–10
10
Neg FS
–9.980000
–9.99393
–9.96607
–9.99435
–9.96565
–5
5
Pos FS
4.990000
4.98502
4.99498
4.98481
4.99519
–5
5
0
0.00000
–0.00362
0.00362
–0.00362
0.00362
–5
5
Neg FS
–4.990000
–4.99498
–4.98502
–4.99519
–4.98481
–2.5
2.5
Pos FS
2.495000
2.49150
2.49850
2.49140
2.49860
–2.5
2.5
0
0.00000
–0.00182
0.00182
–0.00182
0.00182
–2.5
2.5
Neg FS
–2.495000
–2.49850
–2.49150
–2.49860
–2.49140
–1
1
Pos FS
0.998000
0.99659
0.99941
0.99655
0.99945
–1
1
0
0.00000
–0.00074
0.00074
–0.00074
0.00074
–1
1
Neg FS
–0.998000
–0.99941
–0.99659
–0.99945
–0.99655
–0.5
0.5
Pos FS
0.499000
0.49829
0.49971
0.49827
0.49973
–0.5
0.5
0
0.00000
–0.00038
0.00038
–0.00038
0.00038
–0.5
0.5
Neg FS
–0.499000
–0.49971
–0.49829
–0.49973
–0.49827
B/E/M/S/X Series Calibration Procedure
Table 39. NI 6070E/6071E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
52
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.25
0.25
Pos FS
0.249500
0.24913
0.24987
0.24912
0.24988
–0.25
0.25
0
0.00000
–0.00020
0.00020
–0.00020
0.00020
–0.25
0.25
Neg FS
–0.249500
–0.24987
–0.24913
–0.24988
–0.24912
–0.1
0.1
Pos FS
0.099800
0.09964
0.09996
0.09964
0.09996
–0.1
0.1
0
0.00000
–0.00009
0.00009
–0.00009
0.00009
–0.1
0.1
Neg FS
–0.099800
–0.09996
–0.09964
–0.09996
–0.09964
–0.05
0.05
Pos FS
0.049900
0.04981
0.04999
0.04981
0.04999
–0.05
0.05
0
0.00000
–0.00006
0.00006
–0.00006
0.00006
–0.05
0.05
Neg FS
–0.049900
–0.04999
–0.04981
–0.04999
–0.04981
0
10
Pos FS
9.980000
9.97366
9.98634
9.97324
9.98676
0
10
0
0.020000
0.01637
0.02363
0.01637
0.02363
0
5
Pos FS
4.990000
4.98483
4.99517
4.98462
4.99538
0
5
0
0.010000
0.00817
0.01183
0.00817
0.01183
0
2
Pos FS
1.996000
1.99392
1.99808
1.99384
1.99816
0
2
0
0.004000
0.00326
0.00474
0.00326
0.00474
0
1
Pos FS
0.998000
0.99695
0.99905
0.99691
0.99909
0
1
0
0.002000
0.00162
0.00238
0.00162
0.00238
0
0.5
Pos FS
0.499000
0.49846
0.49954
0.49844
0.49956
© National Instruments Corporation
Table 39. NI 6070E/6071E Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
0
0.5
0
0.001000
0.00080
0.00120
0.00080
0.00120
0
0.2
Pos FS
0.199600
0.199374
0.199826
0.199365
0.199835
0
0.2
0
0.000400
0.000308
0.000492
0.000308
0.000492
0
0.1
Pos FS
0.099800
0.099677
0.099923
0.099673
0.099927
0
0.1
0
0.000200
0.000144
0.000256
0.000144
0.000256
Table 40. NI 6070E/6071E Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
53
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.98
9.972304
9.987696
9.971884
9.988116
–10
10
0
0
–0.005930
0.005930
–0.005930
0.005930
–10
10
Neg FS
–9.98
–9.987696
–9.972304
–9.988116
–9.971884
0
10
Pos FS
9.98
9.974744
9.985256
9.974324
9.985676
0
10
0
0.02
0.016506
0.023494
0.016506
0.023494
Table 41. NI 6070E/6071E Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
B/E/M/S/X Series Calibration Procedure
M Series Test Limits
NI USB-6210/6211/6215/6218—16-Bit Resolution
Tables 42 through 44 include values for all USB-6210 (analog input only), USB-6211, USB-6215, and USB-6218
variants.
Table 42. NI USB-6210/6211/6215/6218 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
54
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978209
9.981791
9.977311
9.982689
–10
10
0.000000
0.000000
–0.001369
0.001369
–0.001369
0.001369
–10
10
Neg FS
–9.980000
–9.981791
–9.978209
–9.982689
–9.977311
–5
5
Pos FS
4.990000
4.989044
4.990956
4.988595
4.991405
–5
5
0.000000
0.000000
–0.000695
0.000695
–0.000695
0.000695
–5
5
Neg FS
–4.990000
–4.990956
–4.989044
–4.991405
–4.988595
–1
1
Pos FS
0.998000
0.997780
0.998220
0.997690
0.998310
–1
1
0.000000
0.000000
–0.000158
0.000158
–0.000158
0.000158
–1
1
Neg FS
–0.998000
–0.998220
–0.997780
–0.998310
–0.997690
–0.2
0.2
Pos FS
0.199600
0.199530
0.199670
0.199512
0.199688
–0.2
0.2
0.000000
0.000000
–0.000050
0.000050
–0.000050
0.000050
–0.2
0.2
Neg FS
–0.199600
–0.199670
–0.199530
–0.199688
–0.199512
ni.com
© National Instruments Corporation
Table 43. NI USB-6211/6215/6218 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.977391
9.982609
9.976493
9.983507
–10
10
0.000000
0.000000
–0.002000
0.002000
–0.002000
0.002000
–10
10
Neg FS
–9.980000
–9.982609
–9.977391
–9.983507
–9.976493
Table 44. NI USB-6210/6211/6215/6218 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
55
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
NI USB-6212/6216—16-Bit Resolution
Tables 45 through 47 include values for all USB-6212 and USB-6216 variants.
Table 45. NI USB-6212/6216 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
56
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978189
9.981811
9.977291
9.982709
–10
10
0.000000
0.000000
–0.001389
0.001389
–0.001389
0.001389
–10
10
Neg FS
–9.980000
–9.981811
–9.978189
–9.982709
–9.977291
–5
5
Pos FS
4.990000
4.989034
4.990966
4.988585
4.991415
–5
5
0.000000
0.000000
–0.000705
0.000705
–0.000705
0.000705
–5
5
Neg FS
–4.990000
–4.990966
–4.989034
–4.991415
–4.988585
–1
1
Pos FS
0.998000
0.997778
0.998222
0.997688
0.998312
–1
1
0.000000
0.000000
–0.000160
0.000160
–0.000160
0.000160
–1
1
Neg FS
–0.998000
–0.998222
–0.997778
–0.998312
–0.997688
–0.2
0.2
Pos FS
0.199600
0.199529
0.199671
0.199511
0.199689
–0.2
0.2
0.000000
0.000000
–0.000050
0.000050
–0.000050
0.000050
–0.2
0.2
Neg FS
–0.199600
–0.199671
–0.199529
–0.199689
–0.199511
ni.com
© National Instruments Corporation
Table 46. NI USB-6212/6216 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.977391
9.982609
9.976493
9.983507
–10
10
0.000000
0.000000
–0.002000
0.002000
–0.002000
0.002000
–10
10
Neg FS
–9.980000
–9.982609
–9.977391
–9.983507
–9.976493
Table 47. NI USB-6212/6216 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5.00000
4.99975
5.00025
57
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
NI 6220/6221/6224/6225/6229—16-Bit Resolution
Tables 48 through 50 include values for the PCI-6220 (analog input only), PXI-6220 (analog input only), PCI-6221
(37-pin), PCI-6221 (68-pin), PXI-6221, all USB-6221 variants, PCI-6224 (analog input only), PXI-6224 (analog
input only), PCI-6225, PXI-6225, all USB-6225 variants, PCI-6229, PXI-6229, and all USB-6229 variants.
Table 48. NI 6220/6221/6224/6225/6229 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
58
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.977798
9.982202
9.976900
9.983100
–10
10
0
0.000000
–0.001603
0.001603
–0.001603
0.001603
–10
10
Neg FS
–9.980000
–9.982202
–9.977798
–9.983100
–9.976900
–5
5
Pos FS
4.990000
4.988834
4.991166
4.988385
4.991615
–5
5
0
0.000000
–0.000817
0.000817
–0.000817
0.000817
–5
5
Neg FS
–4.990000
–4.991166
–4.988834
–4.991615
–4.988385
–1
1
Pos FS
0.998000
0.997731
0.998269
0.997641
0.998359
–1
1
0
0.000000
–0.000189
0.000189
–0.000189
0.000189
–1
1
Neg FS
–0.998000
–0.998269
–0.997731
–0.998359
–0.997641
–0.2
0.2
Pos FS
0.199600
0.199506
0.199694
0.199488
0.199712
–0.2
0.2
0
0.000000
–0.000070
0.000070
–0.000070
0.000070
–0.2
0.2
Neg FS
–0.199600
–0.199694
–0.199506
–0.199712
–0.199488
ni.com
© National Instruments Corporation
Table 49. NI 6221/6225/6229 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.977671
9.982329
9.976773
9.983227
–10
10
0
0.000000
–0.001730
0.001730
–0.001730
0.001730
–10
10
Neg FS
–9.980000
–9.982329
–9.977671
–9.983227
–9.976773
Table 50. NI 6220/6221/6224/6225/6229 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
59
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
NI 6250/6251/6254/6255/6259—16-Bit Resolution
Tables 51 through 53 include values for the PCI-6250 (analog input only), PXI-6250 (analog input only),
PCI-6251, NI PCIe-6251, PXI-6251, NI PXIe-6251, all USB-6251 variants, PCI-6254 (analog input only),
PXI-6254 (analog input only), PCI-6255, PXI-6255, all USB-6255 variants, PCI-6259, NI PCIe-6259, PXI-6259,
NI PXIe-6259, and all USB-6259 variants.
Table 51. NI 6250/6251/6254/6255/6259 Analog Input Values
Range (V)
Test Point
24-Hour Limits
2-Year Limits
60
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978447
9.981553
9.978078
9.981922
–10
10
0
0.000000
–0.001094
0.001094
–0.001094
0.001094
–10
10
Neg FS
–9.980000
–9.981553
–9.978447
–9.981922
–9.978078
–5
5
Pos FS
4.990000
4.989174
4.990826
4.988989
4.991011
–5
5
0
0.000000
–0.000547
0.000547
–0.000547
0.000547
–5
5
Neg FS
–4.990000
–4.990826
–4.989174
–4.991011
–4.988989
–2
2
Pos FS
1.996000
1.995663
1.996337
1.995589
1.996411
–2
2
0
0.000000
–0.000225
0.000225
–0.000225
0.000225
–2
2
Neg FS
–1.996000
–1.996337
–1.995663
–1.996411
–1.995589
–1
1
Pos FS
0.998000
0.997818
0.998182
0.997781
0.998219
–1
1
0
0.000000
–0.000117
0.000117
–0.000117
0.000117
–1
1
Neg FS
–0.998000
–0.998182
–0.997818
–0.998219
–0.997781
–0.5
0.5
Pos FS
0.499000
0.498889
0.499111
0.498870
0.499130
–0.5
0.5
0
0.000000
–0.000073
0.000073
–0.000073
0.000073
© National Instruments Corporation
Table 51. NI 6250/6251/6254/6255/6259 Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
2-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.5
0.5
Neg FS
–0.499000
–0.499111
–0.498889
–0.499130
–0.498870
–0.2
0.2
Pos FS
0.199600
0.199533
0.199667
0.199526
0.199674
–0.2
0.2
0
0.000000
–0.000044
0.000044
–0.000044
0.000044
–0.2
0.2
Neg FS
–0.199600
–0.199667
–0.199533
–0.199674
–0.199526
–0.1
0.1
Pos FS
0.099800
0.099752
0.099848
0.099748
0.099852
–0.1
0.1
0
0.000000
–0.000035
0.000035
–0.000035
0.000035
–0.1
0.1
Neg FS
–0.099800
–0.099848
–0.099752
–0.099852
–0.099748
61
Table 52. NI 6251/6255/6259 Analog Output Values
Range (V)
Test Point
24-Hour Limits
2-Year Limits
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978291
9.981709
9.977922
9.982078
–10
10
0
0.000000
–0.001060
0.001060
–0.001060
0.001060
–10
10
Neg FS
–9.980000
–9.981709
–9.978291
–9.982078
–9.977922
–5
5
Pos FS
4.990000
4.989141
4.990859
4.988956
4.991044
–5
5
0
0.000000
–0.000530
0.000530
–0.000530
0.000530
–5
5
Neg FS
–4.990000
–4.990859
–4.989141
–4.991044
–4.988956
B/E/M/S/X Series Calibration Procedure
Table 53. NI 6250/6251/6254/6255/6259 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
62
ni.com
© National Instruments Corporation
NI 6280/6281/6284/6289—18-Bit Resolution
Tables 54 through 57 include values for the PCI-6280 (analog input only), PXI-6280 (analog input only),
PCI-6281, PXI-6281, all USB-6281 variants, PCI-6284 (analog input only), PXI-6284 (analog input only),
PCI-6289, PXI-6289, and all USB-6289 variants.
Table 54. NI 6280/6281/6284/6289 Analog Input Values (Filter On)
Range (V)
Test Point
24-Hour Limits
2-Year Limits
63
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.979393
9.980607
9.979023
9.980977
–10
10
0
0.000000
–0.000308
0.000308
–0.000308
0.000308
–10
10
Neg FS
–9.980000
–9.980607
–9.979393
–9.980977
–9.979023
–5
5
Pos FS
4.990000
4.989671
4.990329
4.989487
4.990513
–5
5
0
0.000000
–0.000154
0.000154
–0.000154
0.000154
–5
5
Neg FS
–4.990000
–4.990329
–4.989671
–4.990513
–4.989487
–2
2
Pos FS
1.996000
1.995865
1.996135
1.995791
1.996209
–2
2
0
0.000000
–0.000066
0.000066
–0.000066
0.000066
–2
2
Neg FS
–1.996000
–1.996135
–1.995865
–1.996209
–1.995791
–1
1
Pos FS
0.998000
0.997913
0.998087
0.997876
0.998124
–1
1
0
0.000000
–0.000042
0.000042
–0.000042
0.000042
–1
1
Neg FS
–0.998000
–0.998087
–0.997913
–0.998124
–0.997876
–0.5
0.5
Pos FS
0.499000
0.498946
0.499054
0.498928
0.499072
–0.5
0.5
0
0.000000
–0.000031
0.000031
–0.000031
0.000031
–0.5
0.5
Neg FS
–0.499000
–0.499054
–0.498946
–0.499072
–0.498928
B/E/M/S/X Series Calibration Procedure
Table 54. NI 6280/6281/6284/6289 Analog Input Values (Filter On) (Continued)
Range (V)
Test Point
24-Hour Limits
2-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.2
0.2
Pos FS
0.199600
0.199568
0.199632
0.199561
0.199639
–0.2
0.2
0
0.000000
–0.000019
0.000019
–0.000019
0.000019
–0.2
0.2
Neg FS
–0.199600
–0.199632
–0.199568
–0.199639
–0.199561
–0.1
0.1
Pos FS
0.099800
0.099775
0.099825
0.099772
0.099828
–0.1
0.1
0
0.000000
–0.000014
0.000014
–0.000014
0.000014
–0.1
0.1
Neg FS
–0.099800
–0.099825
–0.099775
–0.099828
–0.099772
Table 55. NI 6280/6281/6284/6289 Analog Input Values (Filter Off)
64
Range (V)
Test Point
24-Hour Limits
2-Year Limits
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.979320
9.980680
9.978950
9.981050
–10
10
0
0.000000
–0.000331
0.000331
–0.000331
0.000331
–10
10
Neg FS
–9.980000
–9.980680
–9.979320
–9.981050
–9.978950
–5
5
Pos FS
4.990000
4.989635
4.990365
4.989450
4.990550
–5
5
0
0.000000
–0.000166
0.000166
–0.000166
0.000166
–5
5
Neg FS
–4.990000
–4.990365
–4.989635
–4.990550
–4.989450
–2
2
Pos FS
1.996000
1.995850
1.996150
1.995776
1.996224
–2
2
0
0.000000
–0.000071
0.000071
–0.000071
0.000071
© National Instruments Corporation
Table 55. NI 6280/6281/6284/6289 Analog Input Values (Filter Off) (Continued)
Range (V)
Test Point
24-Hour Limits
2-Year Limits
65
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–2
2
Neg FS
–1.996000
–1.996150
–1.995850
–1.996224
–1.995776
–1
1
Pos FS
0.998000
0.997905
0.998096
0.997868
0.998132
–1
1
0
0.000000
–0.000046
0.000046
–0.000046
0.000046
–1
1
Neg FS
–0.998000
–0.998096
–0.997905
–0.998132
–0.997868
–0.5
0.5
Pos FS
0.499000
0.498941
0.499059
0.498923
0.499077
–0.5
0.5
0
0.000000
–0.000034
0.000034
–0.000034
0.000034
–0.5
0.5
Neg FS
–0.499000
–0.499059
–0.498941
–0.499077
–0.498923
–0.2
0.2
Pos FS
0.199600
0.199565
0.199635
0.199558
0.199642
–0.2
0.2
0
0.000000
–0.000021
0.000021
–0.000021
0.000021
–0.2
0.2
Neg FS
–0.199600
–0.199635
–0.199565
–0.199642
–0.199558
–0.1
0.1
Pos FS
0.099800
0.099773
0.099827
0.099769
0.099831
–0.1
0.1
0
0.000000
–0.000016
0.000016
–0.000016
0.000016
–0.1
0.1
Neg FS
–0.099800
–0.099827
–0.099773
–0.099831
–0.099769
B/E/M/S/X Series Calibration Procedure
Table 56. NI 6281/6289 Analog Output Values
Range (V)
Test Point
24-Hour Limits
2-Year Limits
66
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978831
9.981169
9.978462
9.981538
–10
10
0
0.000000
–0.000740
0.000740
–0.000740
0.000740
–10
10
Neg FS
–9.980000
–9.981169
–9.978831
–9.981538
–9.978462
–5
5
Pos FS
4.990000
4.989365
4.990635
4.989181
4.990819
–5
5
0
0.000000
–0.000395
0.000395
–0.000395
0.000395
–5
5
Neg FS
–4.990000
–4.990635
–4.989365
–4.990819
–4.989181
–2
2
Pos FS
1.996000
1.995670
1.996330
1.995596
1.996404
–2
2
0
0.000000
–0.000204
0.000204
–0.000204
0.000204
–2
2
Neg FS
–1.996000
–1.996330
–1.995670
–1.996404
–1.995596
–1
1
Pos FS
0.998000
0.997778
0.998222
0.997741
0.998259
–1
1
0
0.000000
–0.000139
0.000139
–0.000139
0.000139
–1
1
Neg FS
–0.998000
–0.998222
–0.997778
–0.998259
–0.997741
Table 57. NI 6280/6281/6284/6289 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
ni.com
© National Instruments Corporation
S Series Test Limits
NI 6110/6111—12-Bit Resolution
Tables 58 through 60 include values for the PCI-6110 and PCI-6111.
Table 58. NI 6110/6111 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
67
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–42
42
Pos FS
41.58
41.3301
41.8299
41.3294
41.8306
–42
42
0
0
–0.0391
0.0391
–0.0391
0.0391
–42
42
Neg FS
–41.58
–41.8299
–41.3301
–41.8306
–41.3294
–20
20
Pos FS
19.8
19.6780
19.9220
19.6776
19.9224
–20
20
0
0
–0.0216
0.0216
–0.0216
0.0216
–20
20
Neg FS
–19.8
–19.9220
–19.6780
–19.9224
–19.6776
–10
10
Pos FS
9.9
9.8828
9.9172
9.8826
9.9174
–10
10
0
0
–0.0066
0.0066
–0.0066
0.0066
–10
10
Neg FS
–9.9
–9.9172
–9.8828
–9.9174
–9.8826
–5
5
Pos FS
4.95
4.94376
4.95624
4.94368
4.95632
–5
5
0
0
–0.00341
0.00341
–0.00341
0.00341
–5
5
Neg FS
–4.95
–4.95624
–4.94376
–4.95632
–4.94368
–2
2
Pos FS
1.95
1.94744
1.95256
1.94741
1.95259
–2
2
0
0
–0.00145
0.00145
–0.00145
0.00145
–2
2
Neg FS
–1.95
–1.95256
–1.94744
–1.95259
–1.94741
B/E/M/S/X Series Calibration Procedure
Table 58. NI 6110/6111 Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
68
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–1
1
Pos FS
0.99
0.98865
0.99135
0.98863
0.99137
–1
1
0
0
–0.00079
0.00079
–0.00079
0.00079
–1
1
Neg FS
–0.99
–0.99135
–0.98865
–0.99137
–0.98863
–0.5
0.5
Pos FS
0.495
0.494256
0.495744
0.494248
0.495752
–0.5
0.5
0
0
–0.000461
0.000461
–0.000461
0.000461
–0.5
0.5
Neg FS
–0.495
–0.495744
–0.494256
–0.495752
–0.494248
–0.2
0.2
Pos FS
0.198
0.197648
0.198352
0.197645
0.198355
–0.2
0.2
0
0
–0.000239
0.000239
–0.000239
0.000239
–0.2
0.2
Neg FS
–0.198
–0.198352
–0.197648
–0.198355
–0.197645
Table 59. NI 6110/6111 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.99
9.982299
9.997701
9.981879
9.998121
–10
10
0
0
–0.005933
0.005933
–0.005933
0.005933
–10
10
Neg FS
–9.99
–9.997701
–9.982299
–9.998121
–9.981879
Table 60. NI 6110/6111 Counter Values
ni.com
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
© National Instruments Corporation
NI 6115—12-Bit Resolution
Tables 61 through 63 include values for the PCI-6115 and PXI-6115.
Table 61. NI 6115 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
69
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–42
42
Pos FS
41.16
40.980986
41.339014
40.980163
41.339837
–42
42
0
0
–0.036600
0.036600
–0.036600
0.036600
–42
42
Neg FS
–41.16
–41.339014
–40.980986
–41.339837
–40.980163
–20
20
Pos FS
19.6
19.532484
19.667516
19.532092
19.667908
–20
20
0
0
–0.014400
0.014400
–0.014400
0.014400
–20
20
Neg FS
–19.6
–19.667516
–19.532484
–19.667908
–19.532092
–10
10
Pos FS
9.8
9.790032
9.809968
9.789836
9.810164
–10
10
0
0
–0.007420
0.007420
–0.007420
0.007420
–10
10
Neg FS
–9.8
–9.809968
–9.790032
–9.810164
–9.789836
–5
5
Pos FS
4.9
4.895456
4.904544
4.895358
4.904642
–5
5
0
0
–0.003760
0.003760
–0.003760
0.003760
–5
5
Neg FS
–4.9
–4.904544
–4.895456
–4.904642
–4.895358
–2
2
Pos FS
1.96
1.957834
1.962166
1.957795
1.962205
–2
2
0
0
–0.001460
0.001460
–0.001460
0.001460
–2
2
Neg FS
–1.96
–1.962166
–1.957834
–1.962205
–1.957795
–1
1
Pos FS
0.98
0.978809
0.981191
0.978789
0.981211
B/E/M/S/X Series Calibration Procedure
Table 61. NI 6115 Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
70
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–1
1
0
0
–0.000770
0.000770
–0.000770
0.000770
–1
1
Neg FS
–0.98
–0.981191
–0.978809
–0.981211
–0.978789
–0.5
0.5
Pos FS
0.49
0.489305
0.490695
0.489295
0.490705
–1
1
0
0
–0.000411
0.000411
–0.000411
0.000411
–1
1
Neg FS
–0.49
–0.490695
–0.489305
–0.490705
–0.489295
–0.2
0.2
Pos FS
0.196
0.195609
0.196391
0.195605
0.196395
–0.2
0.2
0
0
–0.000189
0.000189
–0.000189
0.000189
–0.2
0.2
Neg FS
–0.196
–0.196391
–0.195609
–0.196395
–0.195605
Table 62. NI 6115 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8
9.786817
9.813183
9.786651
9.813349
–10
10
0
0
–0.008900
0.008900
–0.008900
0.008900
–10
10
Neg FS
–9.8
–9.813183
–9.786817
–9.813349
–9.786651
Table 63. NI 6115 Counter Values
ni.com
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
© National Instruments Corporation
NI 6120—16-Bit Resolution
Tables 64 through 66 include values for the PCI-6120 and PXI-6120.
Table 64. NI 6120 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
71
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–42
42
Pos FS
41.16
41.086432
41.233568
41.085732
41.234268
–42
42
0
0
–0.008906
0.008906
–0.008906
0.008906
–42
42
Neg FS
–41.16
–41.233568
–41.086432
–41.234268
–41.085732
–20
20
Pos FS
19.6
19.569232
19.630768
19.568899
19.631101
–20
20
0
0
–0.003563
0.003563
–0.003563
0.003563
–20
20
Neg FS
–19.6
–19.630768
–19.569232
–19.631101
–19.568899
–10
10
Pos FS
9.8
9.795013
9.804987
9.794846
9.805154
–10
10
0
0
–0.001783
0.001783
–0.001783
0.001783
–10
10
Neg FS
–9.8
–9.804987
–9.795013
–9.805154
–9.794846
–5
5
Pos FS
4.9
4.897360
4.902640
4.897276
4.902724
–5
5
0
0
–0.000906
0.000906
–0.000906
0.000906
–5
5
Neg FS
–4.9
–4.902640
–4.897360
–4.902724
–4.897276
–2
2
Pos FS
1.96
1.958832
1.961168
1.958801
1.961199
–2
2
0
0
–0.000397
0.000397
–0.000397
0.000397
–2
2
Neg FS
–1.96
–1.961168
–1.958832
–1.961199
–1.958801
–1
1
Pos FS
0.98
0.978951
0.981049
0.978934
0.981066
B/E/M/S/X Series Calibration Procedure
Table 64. NI 6120 Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
1-Year Limits
72
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–1
1
0
0
–0.000294
0.000294
–0.000294
0.000294
–1
1
Neg FS
–0.98
–0.981049
–0.978951
–0.981066
–0.978934
–0.5
0.5
Pos FS
0.49
0.489316
0.490684
0.489307
0.490693
–0.5
0.5
0
0
–0.000194
0.000194
–0.000194
0.000194
–0.5
0.5
Neg FS
–0.49
–0.490684
–0.489316
–0.490693
–0.489307
–0.2
0.2
Pos FS
0.196
0.195661
0.196339
0.195658
0.196342
–0.2
0.2
0
0
–0.000098
0.000098
–0.000098
0.000098
–0.2
0.2
Neg FS
–0.196
–0.196339
–0.195661
–0.196342
–0.195658
Table 65. NI 6120 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8
9.793128
9.806872
9.792961
9.807039
–10
10
0
0
–0.001864
0.001864
–0.001864
0.001864
–10
10
Neg FS
–9.8
–9.806872
–9.793128
–9.807039
–9.792961
Table 66. NI 6120 Counter Values
ni.com
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
© National Instruments Corporation
NI 6122/6123—16-Bit Resolution
Tables 67 and 68 include values for the PCI-6122, PXI-6122, PCI-6123, and PXI-6123 (analog input only).
Table 67. NI 6122/6123 Analog Input Values
Range (V)
Test Point
24-Hour Limits
2-Year Limits
73
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.95
9.945926
9.954074
9.945647
9.954353
–10
10
0
0
–0.002880
0.002880
–0.002880
0.002880
–10
10
Neg FS
–9.95
–9.954074
–9.945926
–9.954353
–9.945647
–5
5
Pos FS
4.95
4.947896
4.952104
4.947757
4.952243
–5
5
0
0
–0.001510
0.001510
–0.001510
0.001510
–5
5
Neg FS
–4.95
–4.952104
–4.947896
–4.952243
–4.947757
–2.5
2.5
Pos FS
2.45
2.448836
2.451164
2.448768
2.451232
–2.5
2.5
0
0
–0.000858
0.000858
–0.000858
0.000858
–2.5
2.5
Neg FS
–2.45
–2.451164
–2.448836
–2.451232
–2.448768
–1.25
1.25
Pos FS
1.2
1.199386
1.200614
1.199353
1.200647
–1.25
1.25
0
0
–0.000464
0.000464
–0.000464
0.000464
–1.25
1.25
Neg FS
–1.2
–1.200614
–1.199386
–1.200647
–1.199353
Table 68. NI 6122/6123 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
B/E/M/S/X Series Calibration Procedure
NI PXIe-6124—16-Bit Resolution
Tables 69 through 71 include values for the NI PXIe-6124.
Table 69. NI PXIe-6124 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
74
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.95
9.947151
9.952849
9.946863
9.953137
–10
10
0
0
–0.001217
0.001217
–0.001217
0.001217
–10
10
Neg FS
–9.95
–9.952849
–9.947151
–9.953137
–9.946863
–5
5
Pos FS
4.975
4.973513
4.976487
4.973369
4.976631
–5
5
0
0
–0.000621
0.000621
–0.000621
0.000621
–5
5
Neg FS
–4.975
–4.976487
–4.973513
–4.976631
–4.973369
–2
2
Pos FS
1.99
1.989346
1.990654
1.989289
1.990711
–2
2
0
0
–0.000268
0.000268
–0.000268
0.000268
–2
2
Neg FS
–1.99
–1.990654
–1.989346
–1.990711
–1.989289
–1
1
Pos FS
0.995
0.994638
0.995362
0.994609
0.995391
–1
1
0
0
–0.000149
0.000149
–0.000149
0.000149
–1
1
Neg FS
–0.995
–0.995362
–0.994638
–0.995391
–0.994609
ni.com
© National Instruments Corporation
Table 70. NI PXIe-6124 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.95
9.946739
9.953261
9.946451
9.953550
–10
10
0
0
–0.001460
0.001460
–0.001460
0.001460
–10
10
Neg FS
–9.95
–9.953261
–9.946739
–9.953550
–9.946451
Table 71. NI PXIe-6124 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
75
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
NI 6132/6133—14-Bit Resolution
Tables 72 and 73 include values for the PCI-6132, PXI-6132, PCI-6133, and PXI-6133 (analog input only).
Table 72. NI 6132/6133 Analog Input Values
Range (V)
Test Point
1-Year Limits
76
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.8
9.7958
9.8042
–10
10
0
0
–0.0024
0.0024
–10
10
Neg FS
–9.8
–9.8042
–9.7958
–5
5
Pos FS
4.9
4.8978
4.9022
–5
5
0
0
–0.0012
0.0012
–5
5
Neg FS
–4.9
–4.9022
–4.8978
–2.5
2.5
Pos FS
2.45
2.44875
2.45125
–2.5
2.5
0
0
–0.00067
0.00067
–2.5
2.5
Neg FS
–2.45
–2.45125
–2.44875
–1.25
1.25
Pos FS
1.225
1.22432
1.22568
–1.25
1.25
0
0
–0.00036
0.00036
–1.25
1.25
Neg FS
–1.225
–1.22568
–1.22432
Table 73. NI 6132/6133 Counter Values
ni.com
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
© National Instruments Corporation
NI 6143—16-Bit Resolution
Tables 74 and 75 include values for the PCI-6143 and PXI-6143 (analog input only).
Table 74. NI 6143 Analog Input Values
Range (V)
Test Point
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
–5
5
Pos FS
4.95
4.946455
4.953545
–5
5
0
0
–0.000708
0.000708
–5
5
Neg FS
–4.95
–4.953545
–4.946455
Table 75. NI 6143 Counter Values
77
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99950
5.00050
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
X Series Test Limits
NI 632x—16-Bit Resolution
Tables 76 through 78 include values for the NI PCIe-6320 (analog input only), NI PCIe-6321, and NI PCIe-6323
X Series MIO devices.
Table 76. NI 6320/6321/6323 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
78
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978701
9.981299
9.977803
9.982197
–10
10
0.000000
0.000000
–0.000977
0.000977
–0.000977
0.000977
–10
10
Neg FS
–9.980000
–9.981299
–9.978701
–9.982197
–9.977803
–5
5
Pos FS
4.990000
4.989310
4.990690
4.988861
4.991139
–5
5
0.000000
0.000000
–0.000494
0.000494
–0.000494
0.000494
–5
5
Neg FS
–4.990000
–4.990690
–4.989310
–4.991139
–4.988861
–1
1
Pos FS
0.998000
0.997840
0.998160
0.997750
0.998250
–1
1
0.000000
0.000000
–0.000115
0.000115
–0.000115
0.000115
–1
1
Neg FS
–0.998000
–0.998160
–0.997840
–0.998250
–0.997750
–0.2
0.2
Pos FS
0.199600
0.199549
0.199651
0.199531
0.199669
–0.2
0.2
0.000000
0.000000
–0.000036
0.000036
–0.000036
0.000036
–0.2
0.2
Neg FS
–0.199600
–0.199651
–0.199549
–0.199669
–0.199531
ni.com
© National Instruments Corporation
Table 77. NI 6321/6323 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.977630
9.982370
9.976732
9.983268
–10
10
0.000000
0.000000
–0.001858
0.001858
–0.001858
0.001858
–10
10
Neg FS
–9.980000
–9.982370
–9.977630
–9.983268
–9.976732
Table 78. NI 6320/6321/6323 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
79
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
NI 634x—16-Bit Resolution
Tables 79 through 81 include values for the NI PCIe-6341, NI PXIe-6341, NI USB-6341, NI PCIe-6343, and
NI USB-6343 X Series MIO devices.
Table 79. NI 6341/6343 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
80
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978710
9.981290
9.977811
9.982189
–10
10
0.000000
0.000000
–0.000968
0.000968
–0.000968
0.000968
–10
10
Neg FS
–9.980000
–9.981290
–9.978710
–9.982189
–9.977811
–5
5
Pos FS
4.990000
4.989320
4.990680
4.988871
4.991129
–5
5
0.000000
0.000000
–0.000484
0.000484
–0.000484
0.000484
–5
5
Neg FS
–4.990000
–4.990680
–4.989320
–4.991129
–4.988871
–1
1
Pos FS
0.998000
0.997851
0.998149
0.997761
0.998239
–1
1
0.000000
0.000000
–0.000104
0.000104
–0.000104
0.000104
–1
1
Neg FS
–0.998000
–0.998149
–0.997851
–0.998239
–0.997761
–0.2
0.2
Pos FS
0.199600
0.199560
0.199640
0.199542
0.199658
–0.2
0.2
0.000000
0.000000
–0.000025
0.000025
–0.000025
0.000025
–0.2
0.2
Neg FS
–0.199600
–0.199640
–0.199560
–0.199658
–0.199542
ni.com
© National Instruments Corporation
Table 80. NI 6341/6343 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.977630
9.982370
9.976732
9.983268
–10
10
0.000000
0.000000
–0.001858
0.001858
–0.001858
0.001858
–10
10
Neg FS
–9.980000
–9.982370
–9.977630
–9.983268
–9.976732
Table 81. NI 6341/6343 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
81
B/E/M/S/X Series Calibration Procedure
B/E/M/S/X Series Calibration Procedure
NI 6351/6353—16-Bit Resolution
Tables 82 through 84 include values for the NI PCIe-6351, NI USB-6351, NI PCIe-6353, and NI USB-6353
X Series MIO devices.
Table 82. NI 6351/6353 Analog Input Values
Range (V)
Test Point
24-Hour Limits
2-Year Limits
82
ni.com
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978852
9.981148
9.978483
9.981517
–10
10
0.000000
0.000000
–0.000808
0.000808
–0.000808
0.000808
–10
10
Neg FS
–9.980000
–9.981148
–9.978852
–9.981517
–9.978483
–5
5
Pos FS
4.990000
4.989391
4.990609
4.989207
4.990793
–5
5
0.000000
0.000000
–0.000404
0.000404
–0.000404
0.000404
–5
5
Neg FS
–4.990000
–4.990609
–4.989391
–4.990793
–4.989207
–2
2
Pos FS
1.996000
1.995750
1.996250
1.995677
1.996323
–2
2
0.000000
0.000000
–0.000168
0.000168
–0.000168
0.000168
–2
2
Neg FS
–1.996000
–1.996250
–1.995750
–1.996323
–1.995677
–1
1
Pos FS
0.998000
0.997858
0.998142
0.997821
0.998179
–1
1
0.000000
0.000000
–0.000091
0.000091
–0.000091
0.000091
–1
1
Neg FS
–0.998000
–0.998142
–0.997858
–0.998179
–0.997821
–0.5
0.5
Pos FS
0.499000
0.498924
0.499076
0.498905
0.499095
–0.5
0.5
0.000000
0.000000
–0.000049
0.000049
–0.000049
0.000049
–0.5
0.5
Neg FS
–0.499000
–0.499076
–0.498924
–0.499095
–0.498905
© National Instruments Corporation
Table 82. NI 6351/6353 Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
2-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.2
0.2
Pos FS
0.199600
0.199558
0.199642
0.199550
0.199650
–0.2
0.2
0.000000
0.000000
–0.000026
0.000026
–0.000026
0.000026
–0.2
0.2
Neg FS
–0.199600
–0.199642
–0.199558
–0.199650
–0.199550
–0.1
0.1
Pos FS
0.099800
0.099772
0.099828
0.099768
0.099832
–0.1
0.1
0.000000
0.000000
–0.000019
0.000019
–0.000019
0.000019
–0.1
0.1
Neg FS
–0.099800
–0.099828
–0.099772
–0.099832
–0.099768
Table 83. NI 6351/6353 Analog Output Values
83
Range (V)
Test Point
24-Hour Limits
2-Year Limits
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978481
9.981519
9.978112
9.981888
–10
10
0.000000
0.000000
–0.000990
0.000990
–0.000990
0.000990
–10
10
Neg FS
–9.980000
–9.981519
–9.978481
–9.981888
–9.978112
–5
5
Pos FS
4.990000
4.989251
4.990749
4.989066
4.990934
–5
5
0.000000
0.000000
–0.000495
0.000495
–0.000495
0.000495
–5
5
Neg FS
–4.990000
–4.990749
–4.989251
–4.990934
–4.989066
B/E/M/S/X Series Calibration Procedure
Table 84. NI 6351/6353 Counter Values
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
84
ni.com
© National Instruments Corporation
NI 6356/6358/6366/6368—16-Bit Resolution
Tables 85 through 87 include values for the NI PXIe-6356, NI USB-6356, NI PXIe-6358, NI PXIe-6366,
NI USB-6366, and NI PXIe-6368 X Series simultaneous MIO devices.
Table 85. NI 6356/6358/6366/6368 Analog Input Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
85
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978404
9.981596
9.977506
9.982495
–10
10
0.000000
0.000000
–0.000968
0.000968
–0.000968
0.000968
–10
10
Neg FS
–9.980000
–9.981596
–9.978404
–9.982495
–9.977506
–5
5
Pos FS
4.990000
4.989162
4.990838
4.988713
4.991287
–5
5
0.000000
0.000000
–0.000489
0.000489
–0.000489
0.000489
–5
5
Neg FS
–4.990000
–4.990838
–4.989162
–4.991287
–4.988713
–2
2
Pos FS
1.996000
1.995652
1.996348
1.995473
1.996527
–2
2
0.000000
0.000000
–0.000208
0.000208
–0.000208
0.000208
–2
2
Neg FS
–1.996000
–1.996348
–1.995652
–1.996527
–1.995473
–1
1
Pos FS
0.998000
0.997799
0.998201
0.997710
0.998290
–1
1
0.000000
0.000000
–0.000113
0.000113
–0.000113
0.000113
–1
1
Neg FS
–0.998000
–0.998201
–0.997799
–0.998290
–0.997710
B/E/M/S/X Series Calibration Procedure
Table 86. NI 6356/6358/6366/6368 Analog Output Values
Range (V)
Test Point
24-Hour Limits
1-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.977832
9.982168
9.976934
9.983066
–10
10
0.000000
0.000000
–0.001300
0.001300
–0.001300
0.001300
–10
10
Neg FS
–9.980000
–9.982168
–9.977832
–9.983066
–9.976934
–5
5
Pos FS
4.990000
4.988926
4.991074
4.988477
4.991523
–5
5
0.000000
0.000000
–0.000650
0.000650
–0.000650
0.000650
–5
5
Neg FS
–4.990000
–4.991074
–4.988926
–4.991523
–4.988477
Table 87. NI 6356/6358/6366/6368 Counter Values
86
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
ni.com
© National Instruments Corporation
NI 6361/6363—16-Bit Resolution
Tables 88 through 90 include values for the NI PCIe-6361, NI PXIe-6361, NI USB-6361, NI PCIe-6363,
NI PXIe-6363, and NI USB-6363 X Series MIO devices.
Table 88. NI 6361/6363 Analog Input Values
Range (V)
Test Point
24-Hour Limits
2-Year Limits
87
B/E/M/S/X Series Calibration Procedure
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978711
9.981289
9.978342
9.981658
–10
10
0.000000
0.000000
–0.000949
0.000949
–0.000949
0.000949
–10
10
Neg FS
–9.980000
–9.981289
–9.978711
–9.981658
–9.978342
–5
5
Pos FS
4.990000
4.989321
4.990679
4.989136
4.990864
–5
5
0.000000
0.000000
–0.000475
0.000475
–0.000475
0.000475
–5
5
Neg FS
–4.990000
–4.990679
–4.989321
–4.990864
–4.989136
–2
2
Pos FS
1.996000
1.995722
1.996278
1.995648
1.996352
–2
2
0.000000
0.000000
–0.000196
0.000196
–0.000196
0.000196
–2
2
Neg FS
–1.996000
–1.996278
–1.995722
–1.996352
–1.995648
–1
1
Pos FS
0.998000
0.997844
0.998156
0.997807
0.998193
–1
1
0.000000
0.000000
–0.000105
0.000105
–0.000105
0.000105
–1
1
Neg FS
–0.998000
–0.998156
–0.997844
–0.998193
–0.997807
–0.5
0.5
Pos FS
0.499000
0.498917
0.499083
0.498898
0.499102
–0.5
0.5
0.000000
0.000000
–0.000056
0.000056
–0.000056
0.000056
–0.5
0.5
Neg FS
–0.499000
–0.499083
–0.498917
–0.499102
–0.498898
–0.2
0.2
Pos FS
0.199600
0.199555
0.199645
0.199547
0.199653
B/E/M/S/X Series Calibration Procedure
Table 88. NI 6361/6363 Analog Input Values (Continued)
Range (V)
Test Point
24-Hour Limits
2-Year Limits
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–0.2
0.2
0.000000
0.000000
–0.000029
0.000029
–0.000029
0.000029
–0.2
0.2
Neg FS
–0.199600
–0.199645
–0.199555
–0.199653
–0.199547
–0.1
0.1
Pos FS
0.099800
0.099771
0.099829
0.099767
0.099833
–0.1
0.1
0.000000
0.000000
–0.000020
0.000020
–0.000020
0.000020
–0.1
0.1
Neg FS
–0.099800
–0.099829
–0.099771
–0.099833
–0.099767
Table 89. NI 6361/6363 Analog Output Values
Range (V)
Test Point
24-Hour Limits
2-Year Limits
88
Minimum
Maximum
Location
Value (V)
Lower Limit (V)
Upper Limit (V)
Lower Limit (V)
Upper Limit (V)
–10
10
Pos FS
9.980000
9.978481
9.981519
9.978112
9.981888
–10
10
0.000000
0.000000
–0.000990
0.000990
–0.000990
0.000990
–10
10
Neg FS
–9.980000
–9.981519
–9.978481
–9.981888
–9.978112
–5
5
Pos FS
4.990000
4.989251
4.990749
4.989066
4.990934
–5
5
0.000000
0.000000
–0.000495
0.000495
–0.000495
0.000495
–5
5
Neg FS
–4.990000
–4.990749
–4.989251
–4.990934
–4.989066
Table 90. NI 6361/6363 Counter Values
ni.com
Set Point (MHz)
Lower Limit (MHz)
Upper Limit (MHz)
5
4.99975
5.00025
CVI, National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments. Refer to
the Terms of Use section on ni.com/legal for more information about National Instruments
trademarks. The mark LabWindows is used under a license from Microsoft Corporation. Windows is a
registered trademark of Microsoft Corporation in the United States and other countries. Other product
and company names listed are trademarks or trade names of their respective companies. For patents
covering National Instruments products/technology, refer to the appropriate location: Help»Patents in
your software, the patents.txt file on your media, or the National Instruments Patent Notice at
ni.com/patents.
© 2004–2010 National Instruments Corporation. All rights reserved.
370937K-01
Aug10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement