USER`S MANUAL - Appliances Connection
Model No. GGBE1486.2
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-877-776-4777
Mon.–Fri., 6 a.m.–6 p.m. MST
Sat. 8 a.m.-4 p.m. MST
ON THE WEB:
www.goldsgympowerflex.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
The decals shown here have been
applied to the weight bench. If a
decal is missing or illegible, call
the telephone number on the
front cover of this manual and
request a free replacement
decal. Apply the decals in the
location shown. Note: The decals
may not be shown at actual size.
GOLD'S GYM is a registered trademark of Gold's Gym International, Inc. This product is manufactured and
distributed under license from Gold's Gym International, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on the weight bench before using the weight bench.
before using the weight bench. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of the weight bench.
1. Before beginning any exercise program, con-
7. Inspect and properly tighten all parts regular-
sult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.
ly. Replace any worn parts immediately.
8. Make sure that the pins and knobs are fully
engaged before the weight bench is used.
2. Read all instructions in this manual and all
warnings on the weight bench before using
the weight bench.
9. Wear appropriate clothes while exercising.
Always wear athletic shoes for foot protection while exercising.
3. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
10. The weight bench is designed to support a
maximum user weight of 300 pounds and a
maximum total weight of 610 pounds. Do not
use the weight bench with more than 310
pounds of weight. Do not place more than
150 pounds on the leg lever. Note: The weight
bench does not include weights.
4. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
5. Keep the weight bench indoors, away from
moisture and dust. Place the weight bench on
11. If you feel pain or dizziness while exercising,
stop immediately and cool down.
a level surface, with a mat beneath it to protect the floor or carpet. Make sure that there is
enough clearance around the weight bench to
mount, dismount, and use it.
12. Use the weight bench only as described in
this manual.
6. Keep children under 12 and pets away from
the weight bench at all times.
3
BEFORE YOU BEGIN
Thank you for selecting the versatile GOLD’S GYM®
XRS 20 weight bench. The weight bench offers a
selection of exercise stations designed to develop the
major muscle groups of the body. Whether your goal is
to tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
weight bench will help you to achieve the specific
results you want.
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual).
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
reading this manual, please see the front cover of this
Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled.
To avoid a registration fee for any service needed
under warranty, you must register the weight bench
at www.iconservice.com/registration.
ASSEMBLED DIMENSIONS:
Height: 62 in. (157 cm)
Width: 48 in. (122 cm)
Depth: 73 in. (185 cm)
Weight Rest
Upright
Safety Spotter
Adjustment Knob
Backrest
Curl Pad
Storage Tube
Leg Lever
Backrest Post
Curl Bar
Curl Pin
Seat
Weight Tube
4
PART IDENTIFICATION CHART
See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
the key number of the part, from the PART LIST on page 17. Note: Some small parts may have been preattached. If a part is not in the parts bag, check to see if it has been preattached.
M4 x 16mm
Screw (51)
M5 x 16mm
Screw (50)
M6 x 16mm
Screw (47)
M10 Washer (52)
M8 x 10mm
Set Screw (61)
M6 x 40mm Screw (48)
M8 Washer (54)
M6 x 80mm Screw (46)
M6 Washer (53)
M10 x 85mm Bolt (43)
M10 x 90mm Carriage Bolt (40)
M10 Nylon
Locknut (57)
M10 x 95mm Bolt (42)
M8 Nylon
Locknut (58)
M10 x 77mm Bolt Set (45)
5
M10 x 170mm Bolt (49)
M8 x 70mm Bolt (44)
ASSEMBLY
Make Assembly Easier
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Everything in this manual is designed to ensure
that the weight bench can be assembled successfully by almost anyone. By setting aside
plenty of time, assembly will go smoothly.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
Before beginning assembly, carefully read the following information and instructions:
• Assembly requires the included hex key(s)
and the following tools (not included):
• To hire an authorized service technician to
assemble the weight bench, call 1-800-445-2480.
two adjustable wrenches
one rubber mallet
• Assembly requires two persons.
one standard screwdriver
• Because of its size, the weight bench should be
assembled in the location where it will be used.
Make sure that there is enough clearance to walk
around the weight bench as you assemble it.
one Phillips screwdriver
Assembly may be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
1.
1
Before beginning assembly, make sure
that you have read and understand the
information in the box above. See the
PART IDENTIFICATION CHART on page 5
for help identifying small parts.
4
57
57
Orient the Front Stabilizer (2) with the square
holes toward the floor. Attach the Front
Stabilizer (2) to the Front Leg (4) with two M10
x 90mm Carriage Bolts (40) and two M10 Nylon
Locknuts (57). Do not tighten the Nylon
Locknuts yet.
2
Square
Holes
40
6
2. Attach the Rear Stabilizer (3) to the Frame (1)
with two M10 x 90mm Carriage Bolts (40) and
two M10 Nylon Locknuts (57). Do not tighten
the Nylon Locknuts yet.
2
57
3
40
1
57
Warning
Decals
3. Attach the Seat (18) and the Seat Bracket (59)
to the Frame (1) with two M6 x 80mm Screws
(46) and two M6 Washers (53).
3
Wide End
18
59
53
1
53
46
4. Attach the Frame (1) to the Front Leg (4) with
two M10 x 85mm Bolts (43), two M10 Washers
(52), and an M10 Nylon Locknut (57). Do not
tighten the Nylon Locknut yet.
4
1
4
Finish attaching the Front Leg (4) to the Frame
(1) with four M5 x 16mm Screws (50). Tighten
the Nylon Locknuts (57) used in steps 1, 2,
and 4.
57
52
43
50
7
5. Apply a portion of the included grease to an
M10 x 170mm Bolt (49). Attach the Backrest
Post (15) to the Backrest Frames (16) with the
Bolt, two M10 Washers (52), and an M10 Nylon
Locknut (57). Do not tighten the Nylon
Locknut yet.
5
19
Wide End
Attach the Backrest (19) to the Backrest
Frames (16) with four M6 x 40mm Screws (48)
and four M6 Washers (53). Do not tighten the
Screws yet.
16
Grease
49
16
52
53
48
52
57
53
15
48
6. Apply a portion of the included grease to an
M10 x 170mm Bolt (49). Attach the Backrest
Frames (16) to the Frame (1) with the Bolt, two
M10 Washers (52), and an M10 Nylon Locknut
(57). Set the end of the Backrest Post (15) in
one of the slots in the Frame. Do not overtighten the Nylon Locknut; the Backrest
Frames must pivot easily.
6
Grease
49
52
16
See step 5. Tighten the M10 Nylon Locknut
(57) and the four M6 x 40mm Screws (48).
Do not overtighten the Nylon Locknut; the
Backrest Post (15) must pivot easily.
52
15
57
1
7. Attach the Weight Tube (24) to the Leg Lever
(5) with an M8 x 70mm Bolt (44), a 13mm x
16mm Spacer (55), two M8 Washers (54), and
an M8 Nylon Locknut (58). Then, press a 25mm
Outer Cap (56) onto the Weight Tube.
Slot
7
Bracket
Grease
45
4
56
5
Press the Adapter Cap (60) into the Olympic
Adapter (8). Slide the Olympic Adapter onto the
Weight Tube (24), and tighten an M8 x 10mm
Set Screw (61) into the bottom of the Olympic
Adapter.
45
58 54
24
60
61
8
54
44
8
Apply grease to the barrel of an M10 x 77mm
Bolt Set (45). Attach the Leg Lever (5) to the
Front Leg (4) with the Bolt Set. Make sure that
the barrel of the Bolt Set is inserted through
both sides of the bracket on the Front Leg.
55
8. Insert the Long Pad Tube (36) into the bracket
on the Front Leg (4). Slide two Foam Pads (22)
onto the Pad Tube, and press two Pad Caps
(23) into the ends of the Foam Pads.
8
Repeat this step with the two Short Pad
Tubes (21) and the Leg Lever (5).
23
22
4
36
21
Bracket
5
22
23
21
9. Attach the Bumper (30) to the Curl Bar (17)
with an M4 x 16mm Screw (51).
9
Attach the Curl Bar (17) to the Leg Lever (5)
with the Curl Bar Pin (33). Then, attach the
Tether (34) on the Curl Bar Pin to the Leg Lever
with an M4 x 16mm Screw (51).
17
30
51
5
34
51
33
10. Attach the Curl Pad (20) to the Curl Post (6)
with two M6 x 16mm Screws (47).
10
20
6
47
9
11. Attach a Foot (39) to the Left Upright Base (9)
with an M5 x 16mm Screw (50). Insert an M10 x
90mm Carriage Bolt (40) up into the Left Upright
Base.
11
57
7
52
10
57
Attach the Left Upright Base (9) to the Base (7)
with two M10 x 90mm Carriage Bolts (40), an
M10 x 95mm Bolt (42), four M10 Washers (52),
and three M10 Nylon Locknuts (57). Do not
tighten the Nylon Locknuts yet.
52
42
9
40
39
Repeat this step for the Right Upright Base
(10).
50
40
12. Attach a Storage Tube (14) to an Upright (11)
with two M10 x 95mm Bolts (42), two M10
Washers (52), and two M10 Nylon Locknuts
(57).
12
Attach the Upright (11) to the Left Upright Base
(9) with the M10 x 90mm Carriage Bolt (40),
four M5 x 16mm Screws (50), and an M10
Nylon Locknut (57).
57
14
11
11
52
Repeat this step for the other Upright (11)
and the Right Upright Base (10).
10
50
42
50
See step 11. Tighten all of the M10 Nylon
Locknuts (57) used in step 11.
50
57
9
40
13. Set a Safety Spotter (13) on a set of pegs on
the left Upright (11).
13
Set the other Safety Spotter (13) on a set of
pegs on the right Upright (11). Make sure that
both Safety Spotters are at the same height.
13
11
11
Pegs
14. Make sure that all parts are properly tightened before you use the weight bench. The
use of the remaining parts will be explained
in ADJUSTMENT, beginning on page 11.
13
10
ADJUSTMENT
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 13 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE CURL PAD
To use the Curl Pad (20), remove the indicated
70mm Round Inner Cap (26) and insert the Curl
Post (6) into the Front Leg (4). Tighten an
Adjustment Knob (35) into the Front Leg. Make
sure that the Adjustment Knob passes through a
hole in the Curl Post.
20
6
When performing exercises that do not require the
Curl Pad (20), remove the Curl Pad and reinsert the
70mm Round Inner Cap (26) into the Front Leg (4).
35
26
4
ADJUSTING THE BACKREST
19
To adjust the position of the Backrest (19), lift the
indicated handle on the Backrest Post (15). Raise
or lower the Backrest, and set the Backrest Post in
one of the slots in the Frame (1). Make sure that
the Backrest Post is fully inserted into one of
the slots.
Handle
15
1
USING THE LEG LEVER
To use the Leg Lever (5), slide a weight plate (not
included) onto the Olympic Adapter (8) and secure
it with a Weight Clip (41). Note: When using the
Leg Lever, remove the Curl Bar (17) (see
REMOVING THE CURL BAR on page 12).
5
8
41
11
Weight
Slot
REMOVING THE CURL BAR
When performing exercises that do not require the
Curl Bar (17), pull the Curl Bar Pin (33) out of the
Leg Lever (5) and remove the Curl Bar.
5
17
When attaching the Curl Bar (17), insert the Curl
Bar Pin (33) completely through the Leg Lever (5).
33
ADJUSTING THE WEIGHT RESTS AND THE
SAFETY SPOTTERS
To adjust the height of the Weight Rests (12), raise
the Weight Rests to the desired height and tighten
an Adjustment Knob (35) into each Upright (11).
Make sure that the Weight Rests are at the same
height and that the Adjustment Knobs are fully
tightened into the Uprights.
12
35
11
13
Pegs
35
To adjust the position of the Safety Spotters (13),
move the Safety Spotters to a different set of pegs
on the Uprights (11). Make sure that the Safety
Spotters are at the same height.
12
11
13
12
Pegs
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets performed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
is an individual matter. It is important to avoid overdoing it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise program.
WARMING UP
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
right for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a moderate percentage of their capacity. Select a moderate
amount of resistance and increase the number of repetitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by completing more sets rather than by using high amounts of
resistance.
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Cross Training
Cross training is an efficient way to get a complete and
well-balanced fitness program. An example of a balanced program follows:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an elliptical exerciser or exercise cycle, on Tuesday and Thursday.
• Rest from both strength training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of strength training and aerobic exercise will reshape and strengthen your body, plus develop your heart and lungs.
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
13
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
Rest for a short period of time after each set. The
ideal resting periods follow:
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning workout.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
STAYING MOTIVATED
For motivation, keep a record of each workout. List the
date, the exercises performed, the resistance used,
and the numbers of sets and repetitions completed.
Make copies of the exercise logs found on pages 15
and 16. Use the logs to record your weight and key
body measurements at the end of every month.
Remember, the key to achieving the greatest results is
to make exercise a regular and enjoyable part of your
everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A
P
L
B
Q
C
R
D
S
E
T
F
G
M
U
N
H
V
I
W
J
X
K
14
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
X.
Sternomastoid (neck)
Pectoralis Major (chest)
Biceps (front of arm)
Obliques (waist)
Brachioradials (forearm)
Hip Flexors (upper thigh)
Abductor (outer thigh)
Quadriceps (front of thigh)
Sartorius (front of thigh)
Tibialis Anterior (front of calf)
Soleus (front of calf)
Anterior Deltoid (shoulder)
Rectus Abdominus (stomach)
Adductor (inner thigh)
Trapezius (upper back)
Rhomboideus (upper back)
Posterior Deltoid (shoulder)
Triceps (back of arm)
Latissimus Dorsi (mid back)
Spinae Erectors (lower back)
Gluteus Medius (hip)
Gluteus Maximus (buttocks)
Hamstring (back of leg)
Gastrocnemius (back of calf)
EXERCISE
MONDAY
WEIGHT
SETS
REPS
WEIGHT
SETS
REPS
WEIGHT
SETS
REPS
Date:
/
/
AEROBIC EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
EXERCISE
Date:
/
/
THURSDAY
AEROBIC EXERCISE
Date:
/
/
EXERCISE
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
15
EXERCISE
MONDAY
WEIGHT
SETS
REPS
WEIGHT
SETS
REPS
WEIGHT
SETS
REPS
Date:
/
/
AEROBIC EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
EXERCISE
Date:
/
/
THURSDAY
AEROBIC EXERCISE
Date:
/
/
EXERCISE
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
16
PART LIST—Model No. GGBE1486.2
Key No.
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
1
1
1
1
1
1
1
1
1
1
2
2
2
2
1
2
1
1
1
1
2
6
6
1
6
1
3
22
4
1
2
2
1
Description
Key No. Qty.
Frame
Front Stabilizer
Rear Stabilizer
Front Leg
Leg Lever
Curl Post
Base
Olympic Adapter
Left Upright Base
Right Upright Base
Upright
Weight Rest
Safety Spotter
Storage Tube
Backrest Post
Backrest Frame
Curl Bar
Seat
Backrest
Curl Pad
Short Pad Tube
Foam Pad
Pad Cap
Weight Tube
76mm Round Outer Cap
70mm Round Inner Cap
57mm Round Inner Cap
25mm Round Inner Cap
25mm Square Inner Cap
Bumper
Curl Bushing
Backrest Bushing
Curl Bar Pin
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
*
*
*
*
1
3
1
2
2
2
10
1
6
2
1
1
2
2
4
2
14
6
18
6
2
1
1
19
1
1
1
1
–
–
–
–
R0507A
Description
Tether
Adjustment Knob
Long Pad Tube
Upright Bushing
Upright Spacer
Foot
M10 x 90mm Carriage Bolt
Weight Clip
M10 x 95mm Bolt
M10 x 85mm Bolt
M8 x 70mm Bolt
M10 x 77mm Bolt Set
M6 x 80mm Screw
M6 x 16mm Screw
M6 x 40mm Screw
M10 x 170mm Bolt
M5 x 16mm Screw
M4 x 16mm Screw
M10 Washer
M6 Washer
M8 Washer
13mm x 16mm Spacer
25mm Outer Cap
M10 Nylon Locknut
M8 Nylon Locknut
Seat Bracket
Adapter Cap
M8 x 10mm Set Screw
User’s Manual
Exercise Guide
Grease Packet
Hex Key
Note: Specifications are subject to change without notice. See the back cover of this manual for information
about ordering replacement parts. *These parts are not illustrated.
17
EXPLODED DRAWING—Model No. GGBE1486.2
R0507A
19
29
49
52
16
49
20
16
53
52
52 52
57
29
57
53
48
28
6
17
32
28
15
28
31
23
22
59
3
36
26
23
40
53
4
45
27
22
43
56
5
27
58
54
55
33
57
54 44
46
23
22
24
2
25
60
25
41
40
18
1
57
25
45
27
28
61
50
57
57
22
23
51
8
53
46
52
21
25
57
35
34
32
18
30
51
31
48
47
EXPLODED DRAWING—Model No. GGBE1486.2
12
R0507A
51
51
37
35
38
28
28 14 28
13
51
12
57
51
11
52
37
38
50
35
42
28
50
57
28
13
50
14
11
52
50
57 42
10
52
50
57
50
52 7
40
25
42
50
57
52
39
52
52
40
42
9
52
40
39
50
40
25
19
28
57
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of the manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the part(s) (see the PART LIST and the EXPLODED DRAWING near the
end of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’s responsibility. For
in-home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 245832 R0507A
Printed in China © 2007 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement