GREENHOUSE USER MANUAL

GREENHOUSE USER MANUAL
GRANDIO
G R E E N H O U S E S
Model GRA-ELI812
8x12 GRANDIO ELITE
GREENHOUSE USER MANUAL
© 2013 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved
August 1, 2014 Manual Edition
GRANDIO
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY
G R E E N H O U S E S
Dear Valued Customer,
We would like to congratulate you on your new
Grandio Greenhouse purchase. We are confident
that you have made the right decision in choosing Grandio. Our greenhouses are made with
high quality aluminium and polycarbonate and
will last for many garden seasons to come.
Please take the time to carefully read this
instruction manual for an easier and more
enjoyable assembly experience.
Cheers!
Grandio Greenhouses
Before you begin take time to complete this check list.
Take inventory of all parts using the parts list at the back of this manual.
Be cautious where you place the polycarbonate panels as they will burn grass
or plants if left on top of them in direct sunlight. Note that clear film side of
panels should always face the sun and opal film side faces inside greenhouse.
Plan out when and where you are going to place the greenhouse, we recommend that you place it in an area that will receive direct sunlight and will be
protected from the wind as much as possible
It will take at least (2) people to put the greenhouse together.
Save this owner’s manual for future
reference and if you need our help.
Before your build, make sure you are allowed to build it! Consult all building
codes, as well as City or Municipality ordinances and HOA’s, as you may need
a permit or documentation before you build.
CONTACT OUR CUSTOMER SERVICE
DEPARTMENT at:
Contact your insurance company to make sure your Grandio Greenhouse will
be covered on your policy.
1-866-928-3150
Hours: 8:30a.m.-5:00p.m. Monday through
Friday (Mountain Standard Time)
Backyard Living Source
9543 W. Emerald St., Suite 101
Boise, ID 83704
www.grandiogreenhouses.com
Call your local utilities companies before digging.
Do not attempt to begin construction on a windy day.
Your greenhouse should be built on a flat level surface allowing for drainage.
Read this entire manual to get familiar with all pieces and parts prior to
beginning assembly. Follow the steps outlined in the order presented!
1
IMPORTANT! SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and
inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instructions and identify all parts using the hardware identifier and parts list on pages 35-40. Complete assembly and
proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse.
CAUTION: Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool
dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may
damage panels due to the protective film adhering to panels.)
• Remove approximately 2 inches of film from all polycarbonate sheet edges before installing. Remove all protective film immediately after the construction is completed. Clear film side of panels should always face the sun and opal film side faces inside.
• Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may
carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly.
• Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse.
• Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete.
• If using a ladder during assembly, use extreme caution.
• A clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in
manual. Please anchor the greenhouse down to a firm and level base.
TOOLS YOU WILL NEED FOR ASSEMBLY
• Tape Measure
• Step Ladder
• Masking Tape
• Level
• Work Gloves
• Safety Glasses
• Carpenter Square
• Flathead Screwdriver • 10mm Wrench
• At Least 2 Adults
• No. 1, 2 and 3 Phillips Screwdrivers
2
GRANDIO
TIP
When you see this icon
pay special attention to
the helpful tips we have provided that will
make installation more efficient.
PREPARE A FOUNDATION FOR YOUR
GRANDIO GREENHOUSE
Before assembling your new greenhouse a proper
foundation must be prepared. A number of anchoring options are acceptable, based on wind and
ground conditions in your area.
It is extremely important to have the area prepared
and leveled for installation of your greenhouse prior
to starting the assembly of your Grandio Greenhouse.
Go to www.grandiogreenhouses.com for foundation ideas and tour our online learning center for tips
and tricks for putting your greenhouse together.
IMPORTANT: POLYCARBONATE PANELS
96”
1 3/4”
GUTTERS
Transparent Film
Polycarbonate
Panels
EAVE HEIGHT
Remove approximately 2 inches of film on both sides of
each panel prior to installation. Remove all film immediately after assembly is complete. The UV-Protected side
is covered with transparent film and must face toward
the sun. The side covered in opal film will always face
the interior of the greenhouse.
54”
Sun
LE
144.5”
FT
8X SID
8 E
Opal White Film
3
44”
98”
DOOR HEIGHT
Decide at this time the final orientation of your
Greenhouse. We recommend that you place your
greenhouse in a location where it will receive the
most direct sunlight and will be best protected from
wind and storm conditions.
ROOF PEAK HEIGHT
8X12 GRANDIO ELITE BARN STYLE
GREENHOUSE DIMENSIONS
74”
BACK
L08A
This diagram shows the 8x8 Grandio, for the
8x12 Grandio you will repeat the middle section
of the sides as shown below on LEFT SIDE and
RIGHT SIDE.
601A-B
L08B-X
L08B-X
601A-B
Y1
Y1
Y1
Outside View
Y1
L08B
601A-B
L08C-X
606
609
610
Y8
Y7
603C/616
L08C
Y7
618
Y9 Y10
Y7
602A
609
601A-FL
LEFT SIDE
610
603C
602D
Y4-2
Y8
603C
Y5-2
601B
630
Y5-1
601B
601B
610
609
Y3-1 Y3-2
603E
Y2-1
L08D
603C
601A-FL
604-L
Y1
L08A-X
623B
630
603D
623B
622-L
Y6
622-R
Y6
622
622
620
620
Y6
Y6
623B
623B
619
FRONT
4
610
Y8
L08D
L21
Y11
610
Y1
L08A-X
L08C-X
606
602A
Y7
603C/616
606
602A
602B
Y11
Y8
601A-FR
L08C
Y7
Y8
609
603C
604-R
601A-B
602B
601B
Y2-2
609
Y7
Y11 618
Y10 Y9
601B
630
609
602B
601B
607
Y11
630
Y11
630
601B
Y11
610
603C
602D
Y4-1
602C
Y11
602B
Y8
603C
601B
602B
Y7
L08C-X
606
Y11
602B
602A
606
630
606
602A
Y7
609
606
L08C-X
601A-FR
RIGHT SIDE
8x12 REPEATS THIS SECTION
ON BOTH SIDES
8x12 REPEATS THIS SECTION
ON BOTH SIDES
602A
606
609
GRANDIO
©
G R E E N H O U S E S
ASSEMBLY INSTRUCTION STEPS
STEP ONE: BASE ASSEMBLY
STEP TWO: FRONT ASSEMBLY
STEP THREE: BACK ASSEMBLY
STEP FOUR: MIDDLE ASSEMBLY
STEP FIVE: DOOR ASSEMBLY
5
BASE KIT ASSEMBLY INSTRUCTIONS
**BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
W06/W07 must be cut for patio or deck installation
W06 must be buried in ground.
Drill holes in bottom of base to allow for proper fastener to pass
through prior to moving forward with assembly. You determine and
aquire proper fastener prior to installation.
Outdoor
Ground
Assembly
OR
Base
W08
W07
W06
W06/W07 * Must be
inserted into the ground,
and secured with concrete.
Base
S03/M01
Base
Base
W06
Base
S03/M01
W06
Deck or
Patio
Assembly
Base
W07
S03/M01
S03/M01
DECK OR PATIO
INSTALLATION
W06
Base
B W06/W07 * Must be cut flush with
frame. Use decking screws or
concrete anchors to attach base.
(Fasteners not included).
Use: Quikrete fast setting
concrete to anchor base.
Pour in Quikrete and water
no mixing required.
(Not Included).
W08
W07
Make sure base is squared
and level before setting
anchor into concrete. Use a measuring tape
to ensure all corners are the same. Use level
on all four sides.
GRANDIO
TIP
CUT
6
Base
S03/M01
W06
STEP ONE
W06/W07 Must Be Modified
Base
Use a Hacksaw or Tinsnip to
cut down the length of W06
and W07, then install cut side
down to level surface.
S03/M01
CUT
FRONT FRAME ASSEMBLY INSTRUCTIONS
This picture shows the inside view of front section fully assembled.
601B
601B
We recommend watching
T I P our how to assembly videos
with tricks and tips for easier assembly and
installation of your Grandio Greenhouse at:
www.grandiogreenhouses.com
GRANDIO
Y3-2
601B
603E
Y3-1
601B
603D
Y2-2
Y2-1
L08D
L08D
STEP TWO
Lay flat on ground to
T I P assemble the front frame of
your greenhouse. If possible try to find a
shady area protected from the wind. Panels
can burn grass and plants if in direct light.
GRANDIO
603C
603C
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
GRANDIO
TIP
601A-FR
604-R
604-L
Y1
Y1
619
7
601A-FL
FRONT FRAME ASSEMBLY
2.1 Prethread all S05 screws into the WG01
and WG02’s for ease of installation.
S05
2.2 Use WG01 bracket to attach the (2)
601B’s together with the 603E, secure
parts with the S05 screws provided see .
The WG01 will slide into the groove of the
601B’s, and slide into the groove of the
603E .
WG01
601B
601B
2.3 Install WG02’s into (2) 601B’s then
tighten S05 screws when extrusions are
completely tight see
. Note: the fat end of
the WG02 will always be on the bottom side.
603E
WG02
601B
PRETHREAD SCREWS TIP:
Locate all WG01, WG02,
and S05 screws, pre thread these to make
installation easier. Note that the fat end on
the WG02 will always face downward.
GRANDIO
TIP
WG01
601B
WG02
601B
601B
WG02
603E
601B
8
STEP TWO
Inside View
FRONT FRAME ASSEMBLY
2.4 Insert polycarbonate panels Y3-2 and
Y3-1 into place as shown in
.
2.5: Attach 603E and 603D with W04
and S04/ML01 fasteners as shown in
2.6 Attach the 603D to the 601B’s
WG01
601B
601B
WG02
WG02
603E
.
Y3-2
601B
using the W04-1’s with the S04/ML01
fasteners on both sides as shown in .
W04-1
603D
601B
Y3-1
W04-1
W04
Inside View
601B
S04
ML01
603E
STEP TWO
W04
603D
W04-1
BOLT INSTALLATION TIP:
T I P Locate ML01/S04 nuts and
screws, pre thread into the W04 and
W04-1’s and place in the groove of the
extrusion to make installation easier.
GRANDIO
GRANDIO
W04
TIP
W04-1
Polycarbonate
Panel
9
603D
Transparent Film
Outside Greenhouse
Opal White Film
Inside Greenhouse
Sun
FRONT FRAME ASSEMBLY
2.7 View diagrams and attach the (2) 604’s and (2)
604-R
601A’s to the 619. Note the orientation of the 604’s,
there are 4 different 601A’s (2) for the front and (2) for
the back with different hole placements. The large holes
should be at the top and facing forward on the front
frame assembly. See diagram on this page.
604-L
OUTSIDE
INSIDE
OUTSIDE
601A-FL
OUTSIDE
601A-FR
shows where the corner pieces attach to 619.
shows where the door frame attaches to the 619.
INSIDE
INSIDE
619
OUTSIDE
INSIDE
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
GRANDIO
TIP
TIP: If necessary you may use a screwdriver to wedge behind the
bolt head. This prevents bolt from falling into the track.
601A-FR
Note the larger holes on
601A-FR and 601A-FL
front pieces need to face the
top front of the greenhouse.
GRANDIO
TIP
619
ML01
604-L
ML01
S04
INSIDE DOOR FRAME
S04
10
INSIDE
619
Inside View
STEP TWO
Inside View
FRONT FRAME ASSEMBLY
2.8 Attach 606 to 619, this will hold the
polycarbonate panels in place. If it seems too
tight slide fingers or a screw driver along
edges, gently stretching the 606 to allow
room for panels to fit .
Polycarbonate panel
OUTSIDE
606
619
604-R
604-L
Y1
2.9 Insert Y1 polycarbonate panels into
place, make sure Y1’s slide completely into
606 as show in .
Y1
601A-FL
601A-FR
2.10 Attach (2) 603C’s to (2) L08D’s, then to
606
601A’s and 604’s using S04/ML01 fasteners,
make sure it is snug with the tops of the Y1
panels, then tighten fasteners. See .
619
Inside View
606
2.11 Insert the Y2-2 and Y2-1 polycarbonate
.
STEP TWO
panels as shown in
Y2-2
603C
L08D
GRANDIO
TIP
Polycarbonate
Panel
Transparent Film
Outside Greenhouse
Sun
601A
S04/
ML01
604
L08D
Y1
601A-FR
11
L08D
L08D
603C
Opal White Film
Inside Greenhouse
Y2-1
604-R
603C
601A-FR 604-R
603C
Y1
604-L 601A-FL
FRONT FRAME ASSEMBLY
2.12 Move roof and front section together
and align the WG02’s into the 601A’s, and the
W04-2’s into the 604’s. Insure a snug fit
between the WG02’s, 601B’s and 601A’s and
then tighten the S05 screw as shown in
.
Tighten the W04-2’s with the S04 /ML01 nut
and bolt as shown in
.
WG02
601B
601B
2.13 Attach the L08A-X to L08D and 604 to
square front section loosen S04/ML01
attached to the bottom of the (2) 604’s,
square the frame with carpenter square or use
a measuring tape to make sure corner measurements are the same, also check distance
across from the top of 601A’s, and also to the
bottom of the 601A’s across, make sure
distance is the same. Tighten L08A-X’s to hold
squareness as shown in .
UP
WG02
603D
S04
ML01
604
601B
W04-2
WG02
WG02
S04
ML01
Y2-2
Y2-1
L08D
L08D
601A-FL
603C
W04-2
603D
L08D
S04
ML01
603C
603C
L08A-X
L08A-X
Y1
604-L
601A-FL
Profile View
12
Y1
601A-FR
619
L08A-X
604-R
STEP TWO
W04-2
Fat End
Y3-1
Y3-2
Inside View
BACK ASSEMBLY INSTRUCTIONS
This image shows the inside view of the back wall assembly.
Inside View
601B
WG02
GRANDIO
TIP
Transparent Film
Outside Greenhouse
STEP THREE
Opal White Film
Inside Greenhouse
Y5-2
Y4-2
Make sure the UV coated
GRANDIO
T I P side of the panel faces
outward as indicated on the panels. Avoid
placing the polycarbonate panels in the sun
or near plants until fully assembled.
BOLT INSTALLATION TIP:
T I P Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
601B
Y5-1
602C
602D
Y4-1
602D
WG02
WG02
GRANDIO
WG02
WG01
Sun
601B
Polycarbonate
Panel
601B
L08B
603C
603C
Y1
Y1
603C
603C
Y1
L08B-X
Y1
L08B-X
601A
601A
606
13
L08A
606
BACK CONTINUED
3.1 Prethread all S05 screws into the
WG01 and WG02.
S05
3.2 Use the WG01 bracket to attach the
WG01
601B
(2) 601B’s together, secure parts by
sliding the WG01 into the 601B’s as
shown in diagram
.
601B
3.3 Install WG02’s to connect (2) 601B’s
STEP THREE
when firmly placed between the extrusions tighten the S05 screws, see
.
WG02
Inside View
601B
601B
WG02
601B
WG01
601B
PRETHREAD SCREWS TIP:
Locate all WG01, WG02,
and S05 screws, pre thread these to make
installation easier. Note that the fat end on
the WG02 will always face downward.
GRANDIO
TIP
WG02
601B
14
WG01
WG02
BACK CONTINUED
3.4 Attach (2) 601A-B’s to L08A using S04/ML01
fastener as shown in diagram
.
Attach (2) 602D’s to L08A using S04/ML01 fasteners
as shown in diagram
.
STEP THREE
Attach 603C to L08A using S04/ML01 fastener as
shown in diagram
.
3.5 Attach the (4) 606’s to the L08A as shown in
3.6 Insert the Y4 polycarbonate panels into the
Y1
.
grooves of 601A, 602D and 602C. Make sure Y4
panels are inserted into 606 as shown in
. You may
need to use a screwdriver to gently open the 606 to fit
the polycarbonate panels into the groove of 606.
Y1
Y1
602D
601A-B
Y1
602D
601A-B
602C
606
606
606
606
L08A
602D
601A
602C
Polycarbonate Panel
L08A
ML01
S04
ML01
INSIDE
INSIDE
L08A
L08A
15
S04
606
L08A
BACK CONTINUED
3.7 Attach (4) 603C’s atop each Y-1 panel, then align
the pre threaded S04-ML01 fasteners in each 603C to
the L08B and to each 601A-B, 602D and the 602C.
When aligned tighten the middle first and work your
way outward. See diagrams
,
, .
Y4-2
3.8 Insert the Y5-1 and Y5-2 polycarbonate panels
Y5-2
Y5-1
Y4-1
Y1
601A-B
603C
603C
L08B
603C
Y1
Y1
602D
STEP THREE
into place. Then insert the Y4-1 and Y4-2 into place as
shown in the diagram.
603C
Y1
601A-B
602D
602C
Inside View
603C
601A-B
L08B
603C
603C
603C
L08B
L08B
ML01
602D
S04
16
602D
L08B
602C
BACK CONTINUED
WG01
3.9 Pre thread the S05 screws on WG01, WG02’s
and the ML01/S04 W04-2’s brackets and place
into appropriate extrusion see
,
and
.
Align WG02’s into 601A’s, the W04-2’s into
602D’s, and the WG01 into the 602C. When all
members are snug tighten all fasteners to lock into
place.
W04-2
601B
601B
601B
STEP THREE
Y4-2
602D
Y5-2
Y5-1
Y4-1
601A-B
601B
601A
601B
602C
602D
WG02
W04-2
WG02
WG02
601A-B
Y1
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
Y1
Y1
GRANDIO
TIP
Inside View
17
Y1
BACK CONTINUED
3.11
A. Attach (2) L08B-X’s to (2) 602D’s and
L08A with S04/ML01 as shown in .
L08B-X
601A-B
602D
602C
STEP THREE
B. Attach (2) L08B-X’s to the (2) 601A’s with
fasteners as shown in
.
602D
S04/ML01
602D
L08B-X
L08A
Inside View
L08B-X
L08B-X
ML01
S04
Square by loosening bolts
T I P attached to the tops of the
L08B-X, use measuring tape to make sure
corners to corner measures the same.
601A-B
601A-B
GRANDIO
18
MIDDLE ASSEMBLY INSTRUCTIONS
STEP FOUR
Warning: The person(s) holding the
front or back sections vertical must
continue to do so until the L08C-X angle
supports are attached securely to the
front and base as shown in step 4.5.
Failure to hold front vertical will cause
the front to fall and damage the base kit,
front framing etc. Damage caused by
improper installation is not warrantable.
L08C
W05
Base
Inside
4.1 With no less than 2 people place the
pre assembled front section on top of the
base kit front. Have one person hold the
front vertically while the other attaches
the font section to the base with
W05/S04/ML01 fasteners as shown in
and
.
601A
4.2 Attach front to base with W05 clips
as shown in
.
Front
Side
W05
Base
W05
604
Outside
You will need a minimum of
T I P (2) people to complete the
middle assembly of your greenhouse. The
more people the merrier at this stage of
assembly.
Inside
GRANDIO
Inside View
19
Base
MIDDLE ASSEMBLY CONTINUED
4.3 While the front section is being supported vertically by the other person(s) slide in and attach the L08C’s to the front section
. Using tape temporarily attach the loose end of the L08C’s to the base
601A
Side
L08C
L08C
Inside View
Tape
Base
601A
Front
Side
L08C
L08C
W05
Base
Base
Masking Tape
Inside View
20
Front
STEP FOUR
601A’s using the ML01/S04 nut and bolt as shown in
kit as shown in
.
MIDDLE ASSEMBLY CONTINUED
4.4 Attach L08C-X to 601A with S04/ML01 on both
STEP FOUR
sides as shown in
and
.
4.5 Attach bottom of L08C-X to L08C, W05, and base
as shown in
. Repeat steps for other side. The
L08C-X braces will hold the front up vertically without
assistance. Make sure the W05 clip is snug to the base.
4.6 To install the back section repeat steps 4.1 - 4.5.
Remove tape from L08C’s.
601B
L08C-X
W05
L08C-X
L08C
601A
L08D
L08B-X
Base
Inside View
21
MIDDLE ASSEMBLY CONTINUED
4.7 With 2 people, attach the ridge to front and back by sliding into place as
Side Angle View
, using S04/ML01 fasteners attach the 607 to the 601B’s
607
STEP FOUR
shown in
and
as shown in
.
601B
607
607
601B
Outside View
Inside View
601B
22
607
601B
MIDDLE ASSEMBLY CONTINUED
4.8 Before you attach the 609 you will need to loosen
STEP FOUR
the ML01 (nut) attached to the tops of the L08C-X.
Note: Loosen nuts on only one side at a time, i.e. right
front corner, right rear corner. See
.
Inside View
Inside View
601B
LOOSEN
ML01
With 2 people proceed to install 609’s in this
order, note that 609 must be installed with
groove side down see
. Compare with 610 to
make sure it will slide into 609 upon completion.
L08C-X
601A
L08D OR
L08B
609
601B
2. Now move the loosened S04/ML01 (nut and bolt)
currently attached to the 601A upward to firmly secure
the L08C-X, 609 and 601A together as shown in .
3. Repeat steps 1 and 2 for the other end of 609.
4. With one side firmly secured move to the other
side and repeat steps 1, 2 and 3.
Remove only one L08C-X
T I P at a time. If all L08C-X’s
are removed, the structure will collapse
and cause unwarrantable damage.
GRANDIO
S04/ML01
L08D OR
L08B
1. With one person holding the 609 level and in
position have the other person attach the 609 to the
601B using S04/ML01 (nut and bolt). See
.
5. Attach the mid roof 609’s with S04/ML01 nut
and bolt on both sides see
.
609
601A
Inside
View
Groove
L08C-X
UP
609
23
4.9 Before you attach the 602A’s to the sides
of the greenhouse you will need to loosen the
ML01 (nut) attached to the L08C-X and L08C
located at the base. Once the bottom of
L08C-X’s are loosened on one side attach the
602A’s to the sides of the greenhouse in this
order.
609
STEP FOUR
601B
1. Hold the 602A in place as shown and attach
the top of the 602A to the 609 using
S04/ML01 (nut and bolt). As shown in
.
2. Now attach the bottom of 602A to the L08C
and base using a S04/ML01 (nut and bolt) and
W05 (base clip) as shown in
.
L08C-X
L08C
Note: Where the L08C-X reattaches to the
L08C and the 602A be sure to secure them
with a W05 (base clip) to the base see
.
602A
3. Repeat for the other side.
Polycarbonate Panel
Outside
L08C-X
606
L08C
4.10 Install plastic strip 606 before inserting
polycarbonate sheet Y7’s, see
.
Inside View
loosen bolts attached to L08C-X in all upper
corners. Using a level, adjust 602A and tighten
bolts. Repeat in every corner until the
greenhouse is level. The top edges of Y7’s will
align when greenhouse is level.
602A
609
4.11 After Y7’s are installed on both sides,
602A
W05
L08C
Base
602A
L08C-X
Inside View
24
L08C
W05 CLIP
S04
ML01
Inside View
4.12 Attach 602B’s to 609’s and 607’s as shown in
diagram
on both sides of the upper roof section.
STEP FOUR
Attach (1) 602B between the (2) 609’s, in the middle
only on both sides of roof. Do not attach remaining
602B’s to lower roof section until roof vents are
attached, see
.
607
609
Y11
Y11
4.13 Insert Y11 panels to upper roof section then
slide the 630 into the groove of the upper 609 as
shown to hold Y11’s in place. See
and
. Note
that you may need to loosen the bottoms of some of
the 602B’s to slide the 630 into place as the fit is
very tight. Check that all nut and bolt combos are
tightened again after installation of 630.
Y11
Y11
Y11
601A
L08C
630
630
602B
602B
602B
609
609
609
630
630
602B
609
25
4.14 Assemble the roof window vents as shown below in
and
using the Z05 Screws attach the 615, 616, and 618’s as shown.
,
Y10
Roof Vent
Placement
4.15 Insert assembled window into the end of ridge and slide into
position. See
. Window positions are your discretion however,
must be in the middle for support, do not place nearest the front or
back as you will need a 602B support to keep in window vent in
place. Vents cannot be next to each other on the 8x12 unit.
Y10
4.16 Attach all remaining 602B’s after roof vents are positioned.
Z02
616
618
SUN
Z02
616
615
PC sheet
Note Correct Orientation
SUN
Z02
615
618
Screwdriver
Z02
Outside View
Z02
Y10
Place roof windows in
T I P desired location before
attaching all 602B’s.
GRANDIO
616
618
Z02
26
STEP FOUR
Y10
4.17 To ensure there is no gap in roof vent
position 603C as shown in
. Connect
603C to middle of 602B’s using W04
bracket as shown in
.
618
603C
602B
4.18 Attach HQC01 to 616 with the screws
STEP FOUR
616
Inside view of 603C
603C
616
W04
see
, close roof vent and attach the
handle onto HQC02 middle pin (the first
two holes of the handle to the first two
holes of HQC02). Then attach HQC02 to
603 with Z04 screws, see
.
603C
Note: If you are installing automatic roof vent openers
follow those directions for correct installation.
603C
Y10
Y10
HQC02
HQC01
Y10
HQC01
HQC01
HQC02
HQC01
Z04
603C
616
27
4.19 Insert polycarbonate sheets Y8’s and Y9’s into the lower roof of your greenhouse.
Panels may slide out before gutters are in place. You may want to place a piece of tape on the
panel to prevent sliding as shown below once the panels are in place.
tape after gutter is fully installed.
. Repeat on both sides. Remove
STEP FOUR
4.20 Slide 610 into 609’s groove as shown in diagram
601B
610
609
601A
Y8
Y8
Y9
Y8
Outside View
610
Gutter
609
28
4.21 Attach JG01, JG02, and JG03 end caps to the ridge and gutters on both front
STEP FOUR
and back as shown below. Squeeze a small amount of rubberized silicone or
construction adhesive into the ends of ridge (607) to secure pressure fit end caps
(601). As show in images on the right. Use Z03 screws to attach the JG03 endcaps.
JG01
JG02B
JG03B
Z03
JG02A
JG03A
Z03
29
622-R
623A
622
Side View
Z01
Y6
623A
STEP FIVE
DOOR ASSEMBLY DIAGRAM
Side View
622-L
UP
Z01
622
UP
Double
Ball Catch
620
Y6
620
Z01
Z01
UP
UP
Z01
623B
623B
Z01
J08A
Bottom
View
Inside View
622
Bottom
View
622
J08A
J08A
J08A
30
STEP FIVE
5.1 Insert J08A into the bottom of the 622, note the bottom groove is smaller than the top groove of 622, see .
5.2 Use the Z01 screws to attach the 622 to the 623B, 623A and 620 as shown in .
5.3 Insert Y6 windows into position as shown in , make sure to match doors up to each by laying out parts for other door
now so window panels face the right direction to the sun, and the locks match up.
623A
Side View
622
620
UP
Z01
622
620
620
UP
Y6
623B
Z01
J08A
Y6
Z01
622
Bottom
View
623A
623A
623B
623B
Inside View
622
GRANDIO
TIP
Transparent Film
Outside Greenhouse
J08A
Polycarbonate
Panel
31
Opal White Film
Inside Greenhouse
Sun
so doors will latch closed and slide properly
.
Z01
Side View
Of Top
622-L
* Double
Ball Catch
on the 622-L
623A
Side View
Of Top
622-L
Double
Ball Catch
622-R
* Note the orientation of
the 622-L and 622-R.
Also make sure the right
side is facing out on the
Y6 polycarbonate panels.
UP
* Double
Ball Catch
on the 622-R
UP
Y6
UP
Z01
620
622
UP
Side View
Of Bottom
Bottom
View
J08A
622
Side View
Of Bottom
Y6
Z01
623B
Inside View
J08A
32
STEP FIVE
5.4 Insert J08A into the bottom of the 622, note the bottom has a groove see .
5.5 Attach the 622 to the 623B, 623A and 620 using the Z01 screws as shown in .
5.6 Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball catch match up
STEP FIVE
DOOR ASSEMBLY
5.7 With one person inside greenhouse line up hanging door track with door header, move bolts on
L21 to line up with bolt holes on door header 603D. From the inside attach the S02 nut and bolt set
and tighten while holding firmly as high as possible in position from the outside.
S02
603D
33
L21
5.8 Separately slide the top of the doors in the left and right side of L21, see diagram
STEP FIVE
DOOR INSTALLATION
, until they latch in the middle.
5.9 Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown
below in
, and
.
**We included some felt dots in your Grandio Welcome Kit, please apply to the inside bottom edge of the 623B as shown in
these felt dots will make your doors fit snug and still slide perfectly.
L21
S04
S02
Top
Bottom
Outside View
Inside View
622-HNDL
622-HNDL
622-HNDL
NUT/BOLT
Side Profile View
of Hanging Track
34
622-HNDL
NUT/BOLT
L21
,
S04
STEP FIVE
DOOR INSTALLATION
5.10 Attach L28 to L21 and 601A as shown
below in diagram
and
. Attach (2) J07 to
the ends of L21 see
. The L28 should align
square to the 601A.
5.11 Remove all plastic film from polycarbonate window panels immediately at this step.
603A
S04/ML01
L21
L28
Top View
J07
601A
S02
L21
S04
ML01
L28
35
601A
5.12 Attach the L08E-X to the upper roof
4 3/4”
4 3/4”
section as shown with ML01/S04 fasteners
already in place where the 607 meets the 601B,
and the 609 and the 602B meet see , repeat
this on the front section.
BZ-1
5.13 Attach the L08D-X to the rear lower roof
section where ML01/S04 fasteners are already
in place where the 609 and the 602B meet, and
the 609 and the 601B meet see
, repeat on
the front section.
STEP FIVE
INTERIOR ROOF SUPPORT ASSEMBLY
L08E-X
CZ-1
L08D-X
CZ-1
L08D-X
9”
9”
5.14 Attach the BZ1’s to the roof line as shown
602B
in diagram
with the ML01/S04. We suggest
that you measure up 4 3/4” from the 609 on
both sides to find proper placement of the
BZ1’s.
609
Roof
Vent
607
BZ-1
5.15 Use CZ1’s to support the interior wall at
the eave using the ML01/S04. See diagram
.
We suggest that you measure down 9” and mark
it with a pencil so the base of the CZ-1 will meet
there.
602B
CZ-1
601B
L08E-X
L08D-X
601B
36
PICTURE
PARTS NO. GREENHOUSE
MODELS
DESCRIPTION
QTY
GRA-88
94 5/16” ROOF
1
607
601A-B
ALL MODELS
49 1/8” CORNERS
2
GRA-812
142 5/16“ ROOF
1
601A-FL
ALL MODELS
THESE VARY BY
LOCATION OF HOLES
1
GRA-88
94 5/16” ROOF
4
142 5/16“ ROOFv
4
94 5/16”
2
609
601A-FR
ALL MODELS
THEY WILL BE
PACKED TOGETHER
1
GRA-812
601B
ALL MODELS
57 1/8” CORNER
8
GRA-88
610
GRA-88
49 1/8” SIDE
6
GRA-812
GRA-812
49 1/8” SIDE
10
GRA-88
GRA-88
57 1/8” ROOF
12
GRA-812
57 1/8” ROOF
20
602C
ALL MODELS
84” BACK
1
602D-R
ALL MODELS
67” BACK
1
602A
630
ALL MODELS
67” BACK
94 5/16”
MID ROOF
2
2
142 5/16“
MID ROOF
2
619
ALL MODELS
94 5/16“ SIDES
1
L08A
ALL MODELS
94 5/16” BACK
1
L08B
ALL MODELS
THEY WILL BE
PACKED TOGETHER
1
GRA-88
94 5/16” SIDES
2
GRA-812
142 5/16“ SIDES
2
L08D
ALL MODELS
24 3/16” FRONT
2
L08A-X
ALL MODELS
52 1/4” FRONT
2
1
ALL MODELS
47 5/16” FRONT
1
GRA-88
21 7/8” ROOF
8
GRA-812
21 7/8” ROOF
10
603E
ALL MODELS
17” FRONT
1
604-R
ALL MODELS
65 9/16” FRONT
1
604-L
ALL MODELS
THEY WILL BE
PACKED TOGETHER
1
603D
142 5/16“
SIDE GUTTERS
GRA-812
602B
602D-L
SIDE GUTTERS
L08C
603C
37
GRA-88
22 3/4” ROOF WINDOW
2
L08B-X
ALL MODELS
51 1/8” BACK
2
GRA-812
22 3/4“ ROOF WINDOW
4
L08C-X
ALL MODELS
61” SIDES
4
GRA-88
22 3/4” ROOF WINDOW
2
L08D-X
ALL MODELS
37 3/4” ROOF
4
GRA-812
22 3/4“ ROOF WINDOW
4
L08E-X
ALL MODELS
37 5/8“ ROOF
4
GRA-88
19 9/16” ROOF WINDOW
4
620
ALL MODELS
21 7/16” DOOR
2
GRA-812
19 9/16“ ROOF WINDOW
8
L21
ALL MODELS
95 1/2” DOOR
1
ALL MODELS
FRONT & BACK
2
622
ALL MODELS
ALL PACKED TOGETHER
70 1/4“ DOOR
2
622-L
ALL MODELS
70 1/4“ DOOR
1
622-R
ALL MODELS
70 1/4“ DOOR
1
623A
ALL MODELS
21 1/2” DOOR
2
623B
ALL MODELS
21 5/16“ DOOR
2
J04
ALL MODELS
Not for use in this model
Discard Rollers
4
J07
ALL MODELS
DOOR ENDCAPS
2
J08A
ALL MODELS
DOOR
4
L28
ALL MODELS
DOOR
2
615
616
618
WG01
WG02
W04-2
ALL MODELS
ALL MODELS
GRA-88
FRONT & BACK
FRONT
ROOF
8
4
NOTE HOODLE LOCK
5
W04
GRA-812
ROOF
9
W04-1
ALL MODELS
BACK
2
W11
ALL MODELS
#2 PHILLIPS
SCREWDRIVER
1
Z01
ALL MODELS
4X30
13
GRA-88
4.6X16 MM
9
GRA-812
4.6X16 MM
17
ALL MODELS
3X25 MM
4
Z02
Z03
NOTE HOODLE LOCK
38
GRA-88
ROOF
2
GRA-812
ROOF
4
S02
HQC01
GRA-88
ROOF
2
GRA-812
ROOF
4
ALL MODELS
10 MM NUT DRIVER
1
GRA-88
WINDOW SEAL
14
GRA-812
WINDOW SEAL
18
GRA-88
BASE SECTION
4
GRA-812
72”
97”
4
GRA-88
MID BASE ANCHOR
0
GRA-812
MID BASE ANCHOR
2
GRA-88
MID BASE
BACK PLATE
0
GRA-812
MID BASE
BACK PLATE
2
ALL MODELS
6X20 MM
4
GRA-88
M6X10
17
GRA-812
M6X10
25
GRA-88
M6X14
150
GRA-812
M6X14
195
S05
ALL MODELS
PHILLIPS SCREWS
45
JG01
ALL MODELS
FRONT & BACK
2
JG02 A/B
ALL MODELS
FRONT & BACK
2/2
JG03 A/B
ALL MODELS
FRONT & BACK
2/2
GRA-88
47 1/4”
CENTRAL ROOF SUPPORT
3
GRA-812
47 1/4”
CENTRAL ROOF SUPPORT
5
GRA-88
23 5/8”
LOWER ROOF SUPPORT
6
GRA-812
23 5/8”
LOWER ROOF SUPPORT
10
S03/M01
HQC02
W13
ML01/S04
606
BASE
2
W07
W08
GRA-88
BASE CLIP
15
GRA-812
BASE CLIP
19
W06
ALL MODELS
CORNER ANCHOR
4
622-HNDL
ALL MODELS
DOOR HANDLES
4
622-HNDL
NUT/BOLT
ALL MODELS
PACKED TOGETHER
4
BZ-1
CZ-1
W05
39
Y1
ALL MODELS
FRONT & BACK PANEL
6
Y2-1
ALL MODELS
FRONT PANEL
1
Y6
ALL MODELS
DOOR PANEL
4
GRA-88
SIDE PANEL
8
GRA-812
SIDE PANEL
12
GRA-88
ROOF PANEL
6
GRA-812
ROOF PANEL
8
GRA-88
ROOF VENT PANEL
2
GRA-812
ROOF VENT PANEL
4
GRA-88
BELOW ROOF VENT
2
GRA-812
BELOW ROOF VENT
4
GRA-88
ROOF PANEL
8
GRA-812
ROOF PANEL
12
Y7
Y2-2
ALL MODELS
FRONT PANEL
1
Y3-1
ALL MODELS
FRONT PANEL
1
Y3-2
ALL MODELS
FRONT PANEL
Y4-1
ALL MODELS
BACK PANEL
Y4-2
ALL MODELS
BACK PANEL
Y5-1
ALL MODELS
BACK PANEL
Y5-2
ALL MODELS
BACK PANEL
Y8
1
1
Y9
1
1
Y10
1
Y11
40
NOTES
NOTES
Grandio Greenhouse Limited Lifetime Warranty
1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the
date of original retail purchase on all plastic panels. Additionally the aluminium frame is warrantied for life. The word “defects” is defined as
imperfections that impair the use of the product.
2. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installation, alteration of accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the
control of the manufacturer.
3. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product if the product is defective within
the terms of this warranty, Grandio Greenhouses will repair or replace defective parts at no cost to the purchaser. Shipping charges to and
from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for
removal, installation or replacement of the greenhouse or its components are not covered under this warranty.
4. This warranty does not cover scratching or scuffing of the product that may result from normal usage. In addition, defects resulting from
intentional damage, negligence, unreasonable use will void this warranty.
5. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the
highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use
of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
6. This product is not intended for institutional or commercial use; Grandio Greenhouses does not assume any liability for such use.
7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability for use to extent
permitted by Federal and State Law. Neither Grandio Greenhouses nor any representative assumes any other liability in connection with this
product. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
GRANDIO
G R E E N H O U S E S
Model GRA-88BR-GR & Model GRA-812BR-GR
GREENHOUSE USER MANUAL
KEEP IN A SAFE PLACE FOR REFERENCE
CONTACT US IF YOU NEED HELP
OR
HAVE MISSING OR DAMAGED PARTS
GRANDIOGREENHOUSES.COM
BACKYARD LIVING SOURCE, INC.
9543 W. EMERALD ST., SUITE 101
BOISE, ID 83704
1-866-928-3150
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement