PIN TRAXUser Manual
PINTRAX User Manual
©1997 Artromick International. All Rights Reserved. Artromick and
Pintrax are registered trademarks of Artromick International. All other
trademarks are the property of their respective owners. Rev. 2
PINTRAX User Manual
Contents2
Cart Diagrams
Overall Diagram
Cart and Narcotic Zones
Keypad
Keypad Diagram
Printed Circuit Board Layout
3
4
5
6
General Use
Getting Started
Battery Test
Accessing the Cart
Securing the Cart
Auto Secure
Stopping Auto Secure Alarm
Accessing Electronic Narcotic Drawers
7
8
8
9
9
10
10
Personal Editing
11
Programming the Cart
Basics of Programming
General Programming Overview
Entering Program Mode
Editing Cart Settings
Editing Zone Alarms
Editing Narcotic Alarms
Editing Auto Secure Delay
Editing Beeper Frequency
Editing Narcotic Code Type
Editing General Narcotic Code
Changing the Time
Changing the Date
Changing Personal Editing
Editing User Access
Adding New Users
Editing Cart Access
Editing User Specific Narcotic Box Code
Editing Zone Access
Editing Narcotic Access
Deleting a User
12
13
15
16
17
18
18
19
20
21
22
23
24
24
25
27
28
29
30
31
Recalling from the Cart
Basics of Recalling
General Recalling Overview
Entering Recall Mode
Recalling User Settings
Recalling Events
Recalling Cart Settings
32
33
35
36
37
38
Trouble Shooting
Dealing with a continuous false alarm
Manual override
Backlight does not work
Access if all codes have been lost
Activator in Zone 8 does not open the zone
1
3
4
4
5
PINTRAX User Manual
Cart Diagrams3
Overall Diagram
Narcotic Drawer
LED’s
Locking Bars Activator
Cabinet
Activator
Manual Override Access Panel
Removable Battery
Keypad
PC Communication Jack
Locking Bars
Cabinet Doors
PINTRAX User Manual
Cart Diagrams4
Cart and Narcotic Zones
2
1
3
4
6
7
9
8
2,4,6,8 Cart Zones
1,3,7,9 Narcotic Zones
PINTRAX User Manual
Cart Diagrams5
Keypad Diagram
Cart Information
Liquid Crystal Display
1,3,7,9 Narcotic Zones
2,4,6,8 Cart Zones
Clear Key
Narcotic Access Prompt Key
Battery Test Key
Secure Key
Wake Up Key
Keyswitch
Keypad Lock
PINTRAX User Manual
Cart Diagrams6
Printed Circuit Board Layout
Left Ribbon Cable Connector
Ba c kl i g ht Connecto r
Comm
Connector
Right Ribbon Cable Connector
Keyswitch Connector
Keypad Lock
Keyswitch
E-Prom
#1 Position
E2-Prom
Power Connector
Super Master Switch
(normal position)
PINTRAX User Manual
General Use7
Getting Started
Whenever you use the cart, PINTRAX keeps a record. If, after using the cart, you
don’t press Secure, you will be responsible for everything that happens until the
cart secures itself (Auto Secure).
1. Close all drawers and locking bars.
2. Insert battery.
Printed Circuit Board Revision Level
PC Communication Baud Rate
PCB REV:1
9600
E#04387 FR: 2.4
Temporary Display Symbol
Firmware Revision Level
Cart ID Number
If everything is closed, you will see this.
CART SECURED.
THANK YOU.
If anything is ope n , you’ll hear an alarm , and an Access Code will be requested.
If a user with access to the open area enters a PIN Code the alarm will be disco ntinued.
SECURITY ALARM!
ENTER CODE.
3. Enter Code.
****
ALARM ON ZONE 2
DISCONTINUED
ACCESS ALLOWED.
06/20 01:30PM
Temporary Display Symbol
PINTRAX User Manual
General Use8
Battery Test
Never operate the cart when the battery needs to be charged. Battery Test offers
a simple way to make sure you have enough power to run your cart.
1. Press Battery Test key.
If your battery has enough charge in it to operate the cart, you’ll see this:
BATTERY CHARGE
IS
%
Temporary Display Symbol
If your battery needs to be changed, you’ll see this:
BATTERY NEEDS
CHARGED NOW!
Temporary Display Symbol
Accessing the Cart
1. Press Wake Up.
HELLO!
Temporary Display Symbol
ENTER CODE.
2. Enter 4-digit code.
Use the Clear key if you make a mistake.
****
If you enter a code that isn’t programmed into the cart, you’ll hear a beep,
and you’ll see this:
INCORRECT CODE
PLEASE RE-ENTER
If you enter the wrong code three times, the cart will beep continually or will
not allow another code to be entered for 5 seconds.
3. Press the Activator key on the side of the cart you’re going to open.
The loc king bars in front of the drawers will spring ope n . Open the sliding door
within 5 seconds. If you wait longer than 5 seconds without opening the sliding
door, you will need to re p ress the Activator.
PINTRAX User Manual
General Use9
Securing the Cart
1. Close all drawers, sliding doors and locking bars.
2. Press Secure key.
The cart will power off.
CART SECURED.
THANK YOU.
If the alarm sounds close all zones that may be open.
PLEASE CLOSE
ZONES
If zones appear to be closed see the Trouble Shooting section.
Auto Secure
The cart tries to secure whenever it stays open longer than the preset time.
The time period is adjustable. It can be set anywhere from 1 minute to 99
minutes. (see Auto Secure Delay under Edit Cart Settings)
PINTRAX User Manual
General Use10
Stopping Auto Secure Alarm
CART SECURED.
THANK YOU.
If the Auto Secure Alarm sounds close all zones that may be open or re-enter
the Access Code.
PLEASE CLOSE
ZONES
If the alarm continues and all zones appear to be closed see the Trouble
Shooting section.
Accessing Electronic Narcotic Drawers
Carts generally have from 1 to 4 electronic narcotic drawers. They can be
opened only by people who have been given access. To open a narcotic drawer:
1. Enter your regular 4-digit PIN number.
2. Push the gray button on the side of the cart where the narcotic drawer
is located to open that zone.
3. Press the Narcotic Access Prompt key.
ENTER NARC BOX
CODE & ZONE
4. Enter 3-digit Narcotic Code.
***
Enter the zone where the narcotic drawer is locate d. Na rcotic zones are 1,3,5,7.
(see Ca rt Layout)
ACCESS ALLOWED.
NARC BOX IS OPEN
Green LED lights on the side of the cart indicate an unsecured narcotic drawer.
Narcotic drawers locks will reset in 5 seco n d s.
5. Pull the narcotic drawer open.
The green LED will stay on until the narcotic drawer is closed.
PINTRAX User Manual
Personal Editing11
Personal Editing
If Personal Editing has been activated, nurses can change their own codes
whenever necessary.
Personal Editing is an option that can be enabled or disabled. (see Changing
Personal Editing in the Programming section of this manual)
Personal Editing does not make it possible for nurse/users to perform any of the
other programming functions.
To use Personal Editing:
1. Press Wake Up key on the keypad.
2. Press Program.
ENTER CODE
FOR PROGRAMMING
3. Enter PIN number.
****
CHANGE YOUR CODE
Y/N/END
4. Hit Yes.
EXISTING ACCESS
CODE IS:
USER#3333 ENTER
NEW CODE:
5. Enter your new PIN number.
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart12
Basics of Programming
P I N T RAX is designed to accommodate the various needs and re s ponsibilities of the
people who use it. But first, the following information must be ente red into the
s ys tem for eachpe r s o n .
ID numbe r: Four digits. This number never changes – it identifies the person using
the ca rt for as long as they are ente red into the system.
PIN numbe r:Four digits. Allows the user to gain access to the ca rt, and to start
p rogramming and re call functions if they are authori zed to do so. Can be changed
w h e n ever necessary.
Na rcotic Code: Three digits.This code must be ente red before an authori zed user
can open any of the narcotic drawers. Can be “g e n e ra l”(one-code-for-all) or
“specific”(when using different PIN’s). Either way, the narcotic code can be changed
w h e n ever necessary.
Name: Five letters and/or numbe r s. Se rves as an identifier. Names can only be
e nte red with the PC Access Program.
Areas: Also known as zones. A list of accessible areas for each person using the
ca rt. Could be all areas, no areas, or something in be tween.
Ty pe of Us e r: Each ty pe of user is able to do ce rtain things with the ca rt – they
either are able to program the ca rt, or they aren’t.They have re call abilities, or they
don’t. And so on. But since the ca rts can be tailored to meet individual needs, there
aren’t any hard and fast ru l e s.It all depends on the way the ca rt was set up at the
f a cto ry when it was purchased (or upon changes made afterwards).
Most of the time, though, the following default settings will apply:
Ma s ter Us e r: Can pe rfo rm all programming or re call functions; able to access all
a reas of the ca rt.
Nurse Us e r: Access to ce rtain zones and narcotic zones, determined by the Ma s ter
Us e r. Can Re call Cart Se t t i n g s. May be able to change their own PIN numbers if
that capability has been programmed in.
Technician: Can edit all cart settings except the general Na rcotic Code. Can Re ca l l
eve nts and cart settings, but may not have access to medication or PIN Codes.
PC: Can read cart settings and eve nts using a PC.
Spe c i a l : All the abilities of a Ma s ter User except for cart settings.
Keyswitch: The Keys w i tch acts as a PIN number and can be programmed to have
a c cess to any co m b i n ation of zones – from none, to all, or anything in-be tween.
PINTRAX User Manual
Programming the Cart13
General Programming Overview
When you first enter the Program Mode, hitting No, will move the screen on to the
n ext main heading. Hitting Yes will take you into the subg roup of that heading.
For instance, s u p pose you’re moving down through the main headings: Edit Ca rt
Settings, Edit User Ac cess and Change Personal Code.The way you do it is to keep
hitting No. As soon as you hit Ye s,you’ll find yourself in the subg roup for that
heading.
If you hit Yes at Edit User Access, you’ll have all the options under that heading
available to yo u.
At this po i nt, you’ll see a screen that asks if you wa nt to Add a New Us e r. If you do,
hit Ye s,and the screen will guide you through the proce s s. If not, hit No, and you’ll
m ove on to the next subhead.
When you’ve reached the last stage, you might have several options. At that po i nt,
the Yes and No keys can also be used for scrolling up and down.The arrows on the
keys are there to remind you of this.
If you decide you don’t wa nt to proceed with an ope ration, the End or Es c. key will
take you back to the next level upwa rd s.
PINTRAX User Manual
Programming the Cart14
General Programming Overview
ENTER CODE
FOR PROGRAMMING.
****
End
Yes
EDIT CART
SETTINGS? Y/N/END
If you press Yes, you’ll be able to change a variety of
settings that affect the way your cart works.
No
End
Yes
EDIT USER
ACCESS? Y/N/END
No
End
CHANGE YOUR CODE Yes
Y/N/END
No
EXIT PROGRAMMING
Y/N/END
Pressing Yes, enables you to add and delete users,
adjust the zones and narcotic zones they can
access, change Access Codes and Narcotic Codes.
This option is available to nurse/users only if
activated in Prog ramming Mode (see Changing
Personal Editing).
PINTRAX User Manual
Programming the Cart15
Entering Program Mode
In general, e nte ring the Program Mode makes it possible for the authori zed user to
do two things: 1) change the way the ca rt wo rks by adjusting various settings, and
2) make changes in the capabilities of the people using the ca rt (this includes
adding and deleting users from the system).
1. Press Wake Up key.
2. Press Program key.
User must have programming abilities.
ENTER CODE
FOR PROGRAMMING.
3. Enter 4-digit code.
****
EDIT CART
SETTINGS? Y/N/END
PINTRAX User Manual
Programming the Cart16
Editing Cart Settings
By hitting Yes when you get to Edit Ca rt Se t t i n g s,you’ll have a list of options that
can change the way your ca rt works:
Editing Zone Alarms
Editing Narcotic Alarms
Editing Auto Secure De l ay
Editing Be e per Frequency
Editing Narcotic Code Ty pe
Editing Ge n e ral Narcotic Code
Changing the Clock
Changing the Date
Changing Personal Editing (if act i vated)
As long as you keep hitting No, you’ll go on to the next option.When you get to the
bo t tom of the list, hitting No will take you back to the top of the list. If you wa nt,
you can start back down the list by continuing to hit No.
If you’d rather go to the option just “a bove”where you are – that is, the option you
just passed up – you can hit the End key to go backward s.Continue to hit En d, and
your screen will move back up on the list.To get to Edit CartSe t t i n g s :
1. Enter Programming Mode. (see Entering Program Mode)
EDIT CART
SETTINGS? Y/N/END
PINTRAX User Manual
Programming the Cart17
Editing Zone Alarms
As a rule, the Zone Al a rms are set at the factory, and you wouldn’t have any reason
to change them. However, if you are getting a continuous false alarm , you could
decide to turn a Zone Al a rm off until you can get the problem co rre cte d :
2. Press Yes key on Edit Cart Settings screen.
EDIT ZONE
ALARMS? Y/N/END
a. Press Yes key.
ZONE ALARM | 2468
SETUP
| YYYY
b. Use the keypad to toggle the zones on and off as needed.
Using the numbers 2,4,6 and 8, you can toggle the zones off and on. For
i n s t a n ce, when you hit the number 4, it turns off (you’ll see an N under
the 4). Hit the 4 again, and it comes back on (Y).
“Y” = access allowed
“N” = access not allowed
“–” = no such area on your particular ca rt
c. Press Enter to accept.
Press End to escape with no changes.
EDIT ZONE
ALARMS? Y/N/END
PINTRAX User Manual
Programming the Cart18
Editing Narcotic Alarms
3. Press No key on Edit Zone Alarm screen.
Or End to escape back one step.
EDIT NARC
ALARMS? Y/N/END
a. Use the keypad to toggle the zones on and off as needed.
Using the numbers 1,3,7 and 9, you can toggle the zones off and on. For
instance, when you hit the number 3, it turns off (you’ll see an N under
the 3). Hit the 3 again, and it comes back on (Y).
“Y” = access allowed
“N” = access not allowed
“–” = no such area on your particular cart
b. Press Enter to accept.
Press End to escape with no changes.
Editing Auto Secure Delay
The Auto Se c u reDe l ay is adjustable, and can be set anyw h e re from 1 minute to 99
minute s.(See Auto Secure De l ay under Edit CartSettings)
If the Auto Secure De l ay is set for 99 minute s, for instance, the ca rt will try to
secure itself if there is no act i v i ty on the keypad or loc king bars for that length of
time. However, whenever you use any Act i vator or key, the timer resets itself, and
you begin the time cycle again.
To change the Au to Secure De l ay:
4. Press No key on Edit Narcotic Alarm screen.
EDIT AUTO SECURE
DELAY?
Y/N/END
a. Press Yes key.
CURRENT AUTO
SECURE DELAY:10
SET AUTO SECURE
DELAY
MINS
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart19
b. Enter the amount of delay you want (1-99 mins).
c. Press Enter to accept.
Press End to escape with no changes.
VERIFY DELAY
XX MINS Y/N?
d. Press Yes.
COMPLETED
SUCCESSFULLY.
Temporary Display Symbol
EDIT AUTO SECURE
DELAY?
Y/N/END
Table ofBeeper
Editing
Contents
Frequency
If the sound of your cart’s alarm interferes with another alarm at your facility, you
can change the tone of the be e pe r.Th e re are three options: low, medium or high.
5. Press No key on Auto Secure Delay.
CHANGE BEEPER
FREQUENCY? Y/N
a. Press Yes.
BEEPER FREQUENCY
IS HIGH
BEEPER FREQUENCY
HIGH
b. Press
or
keys to find desired frequency.
c. Press Enter to accept.
Press End to escape with no changes.
COMPLETED
SUCCESSFULLY.
CHANGE BEEPER
FREQUENCY?
Y/N
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart20
Editing Narcotic Code Type
When you change Narcotic Code Ty pes be careful.
By changing from “specific”to “g e n e ra l ,”you’ll be erasing all specific Narcotic Codes
for the people using the system.
If you decided later to switch back to specific Narcotic Codes, you’d have to re - e nter
a specific Narcotic Code for each individual.
When you change from “genera l”to “specific,”the general Narcotic Code will be
erased, and you’ll have to come up with one new general Narcotic Code.
6. Press No key on Change Beeper Frequency.
Or End to escape back one step.
EDIT NARCCODE
TYPE?
Y/N/END
a. Press Yes key.
CURRENT NARCCODE
IS GENERAL
Temporary Display Symbol
MAKE NARCCODE
GENERAL
b. Press
or
to select new Narcotic Code Type.
c. Press Enter to accept.
Press End to escape with no changes.
VERIFY NARCCODE
IS SPECIFIC
Y/N
d. Press Yes.
COMPLETED
SUCCESSFULLY.
EDIT NARCCODE
TYPE?
Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart21
Editing General Narcotic Code
7. Press No key on Edit Narcotic Code Type.
If the Narcotic Code Type is “specific” the Edit General Narcotic Code screen
will not be displayed.
EDIT GENERAL
NARCCODE?Y/N/END
a. Press Yes key.
EXISTING GENERAL
NARCCODE:
Temporary Display Symbol
NEW GENERAL
NARCCODE:
b. Enter desired value.
c. Press Enter to accept.
Press End to escape with no changes.
VERIFY NEW GEN
NARCCODE:236 Y/N
d. Press Yes.
COMPLETED
SUCCESSFULLY.
EDIT GENERAL
NARCCODE?Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart22
Changing the Time
8. Press No key on Edit Narcotic Code Type or Edit General Narcotic Code.
Which screen you’ll see will depend on whether you have a “specific” or
“general” Narcotic Code Type.
CHANGE TIME?
Y/N/END
a. Press Yes key.
CURRENT VALUE:
04/22/97
08:21
Temporary Display Symbol
ENTER
| HHMMSS
NEW TIME |
b. Enter desired value.
Use military time – 1100 for 11am, 1300 for 1pm, 2200 for 10pm, etc.
Enter two-digits each for Hours (HH), Minutes (MM) and Seconds (SS).
For instance, 1:09 pm and 8 seconds would be entered as 13 09 08.
If you make a mistake, use the Clear key to erase or press End to escape
with no changes.
c. Press Enter.
COMPLETED
SUCCESSFULLY.
CHANGE TIME?
Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart23
Changing the Date
9. Press No key on Change Time.
CHANGE DATE?
Y/N/END
a. Press Yes key.
CURRENT VALUE:
04/22/97
08:21
Temporary Display Symbol
ENTER
| MMDDYY
NEW DATE |
b. Enter the correct Date.
Enter two-digits for each Month (MM), Day (DD) and Year (YY).
For instance, February 3, 1998 would be 02 03 98.
c. Press Enter.
Press End to escape with no changes.
COMPLETED
SUCCESSFULLY.
CHANGE DATE?
Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart24
Changing Personal Editing
PINTRAX offers the option of Personal Editing – allowing nurse/users to change
their own codes whenever necessary.
10. Press No key on Change Date.
CHANGE PERSONAL
EDITING
Y/N/END
a. Press Yes key.
PERSONAL EDITING
IS ENABLED.
Temporary Display Symbol
PERSONAL EDIT
IS ENABLED
a. Press
or
to select desired value.
c. Press Enter to accept.
Press End to escape with no changes.
COMPLETED
SUCCESSFULLY.
Temporary Display Symbol
CHANGE PERSONAL
EDITING
Y/N/END
Editing User Access
This option lets you change the zones or narcotic zones that a particular individual
is able to access.
1. Enter Programming Mode.
Press Wake Up key, press Program key, enter PIN number.
Press No until you see the Edit User Access screen.
EDIT USER
ACCESS? Y/N/END
PINTRAX User Manual
Programming the Cart25
Adding New Users
P I N T RAX guides you through all the decisions you have to make when Adding a
New User – Ty pe of User (nurse/user, supervisor, etc.), Zones Access, Narcotic Acce s s,
ID numbe r s, PIN numbers and more.To be g i n :
2. Press Yes key on Edit User Access screen.
ADD NEW USER?
Y/N/END
a. Press Yes key.
PICK USER TYPE
NURSE
b. Press
or
to select user type.
c. Press Enter to accept.
ENTER NEW
USER#
d. Enter the 4-digit User ID.
This is the perm a n e nt number that identifies the user. This is not the
Ac cess Code. See Basics of Prog ramming under Prog ramming the Ca rt.
e. Press Enter to accept.
USER#2345 ENTER
NEW CODE:
f. Enter 4-digit Access Code.
g. Press Enter to accept.
USER#2345 VERIFY
CODE:8977
Y/N
h. Press Yes.
USER#2345 | 2468
ZONE ACCESS | YYYY
PINTRAX User Manual
Programming the Cart26
i. Use the keypad to toggle the zones on and off as needed.
Using the numbers 2,4,6 and 8, you can toggle the zones off and on.
For instance, when you hit the number 4, it turns off (you’ll see an N under
the 4). Hit the 4 again, and it comes back on (Y).
“Y” = access allowed
“N”= access not allowed
“–” = no such area on you particular cart
j.
Press Enter to accept.
USER# 2345 | 1379
NARC ACCESS | YYYY
k. Set narcotic access as needed for narcotic zones 1,3,7 and 9.
Use the same method as you did to set the regular zone access (see 2i above).
l. Press Enter to accept.
COMPLETED
SUCCESSFULLY.
ADD NEW USER?
Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart27
Editing Cart Access
This is where you go to change the User PIN number (or Access Code) of any
individual using the cart.
3. Press No key on Add New Users.
(See 2i above)
EDIT CODE
ACCESS? Y/N/END
a. Press Yes key.
ENTER USER#
THEN PRESS ENTER
b. Enter the 4-digit User Code.
c. Press Enter.
EXISTING ACCESS
CODE IS:
Temporary Display Symbol
USER#2345 ENTER
NEW CODE:
d. Enter the new 4-digit User Code.
e. Press Enter.
USER#2345 VERIFY
CODE:8978
Y/N
f. Press Yes.
COMPLETED
SUCCESSFULLY.
EDIT CODE
ACCESS? Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart28
Editing User Specific Narcotic Box Code
User Specific Na rcotic Box Codes are necessary only when the Narcotic Code Type
is “specific.” If the Na rcotic Code is “g e n e ra l ,”then the same Narcotic Code applies
to eve ryone who is authori zed to access the narcotic are a s.To use specific narc
codes each user must have their own unique access cod e. With a general narc
code users may share a code or have a specific access code.
4. Press No key on Edit Code Access.
EDIT NARC BOX
CODE?
Y/N/END
This screen will appear only when the Narcotic Ty pe is “specific.”When the Narcotic
Code Type is “genera l ,”“specific”Narcotic Codes don’t exist,be cause they aren’t needed.
a. Press Yes key.
ENTER USER#
THEN PRESS ENTER
b. Enter the 4-digit ID of the user to be edited.
This is the permanent number that identifies the user. This is not the
Access Code. See Basics of Programming under Programming the Cart.
c. Press Enter.
EXISTING NARC
BOX CODE IS:671
Temporary Display Symbol
If no “specific”Narcotic Code has been selected, you’ll see “–––”instead of a numbe r.
USER#2345 ENTER
NEW NARCCODE:
d. Enter the new 3-digit Narcotic Code.
e. Press Enter.
USER#2345 VERIFY
NARCCODE:222 Y/N
f. Press Yes.
COMPLETED
SUCCESSFULLY.
EDIT NARC BOX
CODE?
Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart29
Editing Zone Access
When you wa nt to add or eliminate access to any cart zones for a specific user, this
is how to go about it. For narcotic zones, see the next section – Editing Narcotic
Zone Access.
5. Press No key at the Edit Code Access screen.
If the Narcotic Code is “general,” your screen will go directly to Edit Zone Access.
If the Narcotic Code is “specific,” your screen will go to Edit Narcotic Box Code.
Hit No again to get to the following screen.
EDIT ZONE
ACCESS? Y/N/END
a. Press Yes key.
ENTER USER#
THEN PRESS ENTER
b. Enter the 4-digit ID of the user to be edited.
This is the permanent number that identifies the user. This is not the
Access Code. See Basics of Programming under Programming the Cart.
c. Press Enter.
USER#2345 | 2468
ZONE ACCESS | YYYY
d. Set zone access as needed for zones 2,4,6 and 8.
Using the numbers 2,4,6 and 8 on the keypad, you can toggle the zones on
and off. For instance, when you hit the number 4, it turns off (you’ll see an
N under the 4). Hit the 4 again, and it comes back on (Y).
“Y” = access allowed
“N” = access not allowed
“–” = no such area on your particular cart
e. Press Enter to accept.
COMPLETED
SUCCESSFULLY.
EDIT ZONE
ACCESS? Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart30
Editing Narcotic Access
Editing Na rcotic Ac cess allows you to add or delete access to narcotic zones for
a ny specific individual with access to the ca rt zone that the narcotic is located in.
6. Press No on Edit Zone Access.
EDIT NARC
ACCESS? Y/N/END
a. Press Yes key.
ENTER USER#
THEN PRESS ENTER
b. Enter the 4-digit ID of the user to be edited.
c. Press Enter.
USER#2345
| 1379
NARC ACCESS | YYYY
d. Toggle 1,3,7 and 9 keys to set zone access as needed.
Setting narcotic zones works the same way as setting regular zo n e s.
See 5d above if you have questions about toggling.
e. Press Enter to accept.
COMPLETED
SUCCESSFULLY.
EDIT NARC
ACCESS? Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Programming the Cart31
Deleting a User
One of the main adva ntages offered by PINTRAX is the ext remely high level of
s e c u ri ty. Si n ce each individual user has their own specific Ac cess Code, i t’s an easy
m at ter to take them off the sys tem if the time comes when they no longer have a
need to access the ca rt.
Be certain never to delete the only master user!
7. Press No on Edit Narcotic Access.
DELETE USER?
Y/N/END
a. Press Yes key.
ENTER USER#
THEN PRESS ENTER
b. Enter the 4-digit ID of the user to be edited.
c. Press Enter.
DELETE USER# 2345
VERIFY Y/N/END
d. Press Yes key.
COMPLETED
SUCCESSFULLY.
DELETE USER?
Y/N/END
Temporary Display Symbol
PINTRAX User Manual
Recalling from the Cart32
Basics of Recalling
Re call Mode allows you to look at up to 3,000 of the past eve nts starting with the
most re ce nt and wo rking backwa rd.
Re call identifies people who have accessed the ca rt, and includes what times and
which zones they’ve ente red. Re call also allows a user to see – but not change –
the cart settings.
Re call also makes it possible to find out an individual’s Access Codes, ID numbe r,
and which zones they are authori zed to ope n . It also lists things like bat te ry
removal and installation.
If you have purchased the PINTRAX computer prog ram, you can use your PC to
l ook at this information.
However, it is impossible to pe rfo rm any of the programming functions while in
Re call Mode.To change a user ID for instance, or to adjust a ca rt setting, you’ll have
to exit Re call Mode and enter Prog ram Mode.
PINTRAX User Manual
Recalling from the Cart33
General Recalling Overview
The Re call Mode is set up in a hiera rc h i cal system, just like the Programming
Mod e, with main headings, subheadings, and te rt i a ry headings.
When you first enter the Re call Mode, hitting No will move the screen on to the
n ext main heading. Hitting Yes will take you into the subg roup of that heading.
For instance, s u p pose you’re moving down through the main headings:
As long as you keep hitting No, you’ll move on to the next one: Link to PC, Re ca l l
User Settings, Re call Eve nts and Re call Cart Settings.
As soon as you hit Ye s,you’ll find yourself in the subg roup for that heading.
When you’ve gone as deep as you can go – when you’ve reached the po i nt where
you are able to re call info rm ation – the Yes and No keys can be used for scrolling
up and down.The arrows on the keys are there to remind you of this.
If you decide you wa nt to jump back to the next level up – from a secondary
heading to the main heading, for instance, the End key will take you there.
PINTRAX User Manual
Recalling from the Cart34
General Recalling Overview
End
Yes
LINK TO PC?
Y/N/END
No
End
Yes
RECALL USER
SETTINGS? Y/N/END
No
End
Yes
RECALL EVENTS?
Y/N/END
No
End
Yes
RECALL CART
SETTINGS? Y/N/END
No
EXIT RECALL?
Y/N/END
No
Pressing Yes, enables you to hook up to a PC, provided
you’ve purchased the PC program (See the PINTRAX
PC Access Program Manual for more information).
If you press Yes, you’ll be able to get info rm ation
about any or all users, including cod e s,user/type,
what zones and narcotic zones they have access to.
If you press Yes, you’ll be able to see a list of
approximately 3,000 oc c u rrences, starting with the
most re ce nt.
If you press Yes, you’ll be able to see which alarms are
a ct i vate d, whether the Narcotic Code is “genera l”or
“s pe c i f i c”and more.
PINTRAX User Manual
Recalling from the Cart35
Entering Recall Mode
To enter Re call Mode, a user must have re call abilities. In general, supervisors with
p rog ramming abilities are able to enter Re call Mod e. It is impo rtant to re m e m ber
that you cannot make any changes at all in Re call Mod e.
1. Press Wake Up key.
2. Press Recall key.
ENTER CODE
FOR RECALLING.
3. Enter 4-digit PIN Code.
****
If you have the ability to connect to a PC, the following screen will appear.
(see the PINTRAX PC Access Manual for information on linking to a PC)
LINK TO PC?
Y/N/END
4. Press No key.
RECALL USER
SETTINGS? Y/N/END
PINTRAX User Manual
Recalling from the Cart36
Recalling User Settings
1. Press No key on Link to PC screen.
RECALL USER
SETTINGS? Y/N/END
2. Press Yes key.
PRINT USERS?
Y/N/END
Note: If you select yes, you will have an option that is no longer
available. You will need to select No to continue.
3. Press No key.
User type K=Keyswitch, M=Master, N=Nurse, T=Technician,
P=PC, S=Special
K#0002 CODE:1235
NC:432 Z-46X1379
ID: 4-digit Code or Keys for Keyswitch.
Access Code: 4 digits or “––––” for Keyswitch.
See Basics of Programming under Programming the Cart.
Zone/Narcotic Access “X”= no permission,“–”= zone not present,
“number” = granted
Narcotic Code
4. Use the
and
keys to scan through the users.
5. Press the End key twice to return to Recall User Settings screen.
PINTRAX User Manual
Recalling from the Cart37
Recalling Events
1. Press No on Recall User Settings.
RECALL EVENTS?
Y/N/END
2. Press Yes key.
PRINT EVENTS?
Y/N/END
Note: If you select yes, you will have an option that is no longer
available. You will need to select No to continue.
3. Press No key.
User ID.
Date of Event.
Time of Event (military time).
0001 04/22 10:30
SECURED
Event
4. Press
to go backward in time.
Press
to go forward in time.
The events start at the most recent event and work backward.
5. Press the End key twice to return to the Recall Events screen.
PINTRAX User Manual
Recalling from the Cart38
Recalling Cart Settings
Re call Ca rt Settings makes it possible for you to check such things as which zone
alarms are activated, whether the Narcotic Codes are “general” or “specific,” the date,
the time and how long the Au to Se c u re De l ay is. Re m e m ber that no changes are
possible in Recall Mode.To make changes, you have to be in the Programming Mode.
1. Press No on Re call Events.
RECALL CART
SETTINGS? Y/N/END
2. Press Yes key.
PRINT CART
SETTINGS? Y/N/END
Note: If you select yes, you will have an option that is no longer
available. You will need to select No to continue.
3. Press No.
The white triangle indicates that you have reached the end of the loo p. In the
case of the screen be l ow, if you were to hit down (or No), the screen wouldn’t
go anyw h e re.To see other options, you’d have to hit up (or Yes). The black
t riangle indicates that there are other options in that direction.
ALARM | 2468
ON ZONES | YYYY
Al a rm settings for standard non-narcotic zones 2,4,6 and 8.
( See Ca rt Layout section for locations.)
“Y” = alarm on in that are a .
“N” = alarm off in that are a .
“–” = area does not exist on your particular ca rt.
PINTRAX User Manual
Recalling from the Cart39
4. Press the
key.
ALARM | 1379
ON NARCS | YYYY
Alarm settings for standard narcotic zones 1,3,7 and 9.
“Y” = alarm on in that area.
“N” = alarm off in that area.
“–” = area does not exist on your particular cart.
5. Press the
key.
CURRENT AUTO
SECURE DELAY:20
6. Press the
key.
NARC CODE TYPE
IS:GENERAL
7. Press End twice to return to the Re call Ca rt Settings screen.
PINTRAX Trouble Shooting
PINTRAX User Manual
Trouble Shooting1
Dealing with a continuous false Alarm
Double check to be certain eve rything on the cart is completely closed – doors,
d rawers, narcotic drawers and loc king bars.
If the alarm is still sounding, the problem may be in the hardwa re. Until the
p roblem can be taken ca re of by a servicetechnician, turn off the pe ri m e ter alarm
in the alarming are a . He re’s how:
1. Press the Program key.
PLEASE PRESS THE
SECURE KEY.
2. Press the Secure key.
ENTER CODE
FOR PROGRAMMING.
3. Enter PIN Code.
You must have programming capabilities for your code to work here.
If not, your supervisors code will probably work.
****
At this point the alarm should stop, as long as the person entering their
code has programming capabilities.
EDIT CART
SETTINGS? Y/N/END
PINTRAX User Manual
Trouble Shooting2
4. Press Yes key at the Edit Cart Settings screen.
EDIT ZONE
ALARMS? Y/N/END
a. Press the Yes key at the Edit Zone Alarms screen.
ZONE ALARM | 2468
SETUP
| YYYY
b. Use the keypad to turn off the alarm.
The 2,4,6 and 8 keys each toggle the alarm off (and on again) in their
zones 2,4,6 and 8.
c. Press Enter to accept.
Press End to escape with no changes.
EDIT ZONE
ALARMS? Y/N/END
PINTRAX User Manual
Trouble Shooting3
Manual Override
If you’re not getting power, you can open the cart manually by using the
push/pull manual access cables, located under the access panel. The access panel
is located above the keypad and to the left of the battery.
1. Remove the panel, using the Manual Access Panel Key (this is a tubular key)
You’ll see several wires – each with a small ball crimped on the end.
2. Pull on the access cable for the area you want to open.
First, make sure you have the access cable for the right Area (see page 4 of
this manual for the zone chart). Place the end of the manual access tool
around the ball on the end of the access cable. Pull on it about 2'' for zones
4&6, and about 1/4'' for zones 1,3,7, & 9. If you don’t have an access tool, you
can use a small pair of pliers. The drawing below shows the locations of each
zones cable.
3. Push on the access cable to reset the latch (be careful not to bend the cable).
4. Zone 8 manual access is located under the keypad.
Manual
Access Tool
Narc Zone 1
Narc Zone 3
Zone 4
Zone 6
Narc Zone 9
Narc Zone 7
PINTRAX User Manual
Trouble Shooting4
Backlight does not work
The backlight should be on whenever the ca rt is awa ke (you may not see this
d u ring daylight hours), and the LCD is act i ve. If you have trouble reading the LCD in
low light, then the backlight is not worki n g. If this happe n s, the backlight connector
has probably come unplugged.To re connect the backlight:
1. Important! Remove the battery to prevent electrical shock!
The LCD backlight driver puts out a high voltage.
2. Remove the electronics panel using the Keypad Panel Key.
3. Check to make sure the backlight wires are connected to P1.
If they are connected, then pull the connector off of P1 and push back on
firmly to re-seat it.
4. Replace the panel and insert the battery.
Access if all Codes have been lost.
The cart can be accessed if all codes have been lost, but you will need to contact
Artromick to obtain the super master code. Each ca rt has a unique super maste r
code which is set up at the facto ry. In normal ope rations this code is not act i ve – if
it is ente red the cart will tre at it as a bad code. If needed the code can be act i vate d
by pe rforming the fo l l owing ste p s.
1. Important! Remove the battery to prevent electrical shock!
The LCD backlight driver puts out a high voltage.
2. Remove the electronics panel using the Keypad Panel Key.
3. Move the actuator of slide switch SW1 to the position marked MC.
4. Replace the panel and insert the battery.
The super master code is now act i vate d. Ente ring the code will allow access to
all areas and all prog ramming and re calling features.
PINTRAX User Manual
Trouble Shooting5
Activator in Zone 8 does not open the Zone
This error can occur if the keypad panel is re m oved and then re p l a ced in such a
way that the wires or the ri b bon cable inte rfe re with ope ration of the solenoid or
the micro switc h . If this is the problem it is easily fixed by re m oving the keypad
panel, and ca refully reinstalling it making sure that no wires are inte rfering.
Remember to remove the battery before removing the panel! The LCD
backlight driver puts out a high voltage. Remove the battery to prevent
electrical shock.
Medication Systems Worldwide
www.artromick.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement