MN67120 ENG
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 1 of 15
Industrial Electronic Devices
User Manual
Revision 2.003
English
RS232 / RS485 / Ethernet - Converter
(Order Code: HD67120)
for Website information:
www.adfweb.com?Product=HD67120
for Price information:
www.adfweb.com?Price=HD67120
Benefits and Main Features:
Interfacing directly to 485 without other adaptor
Galvanic isolation between Ethernet and 232/485 bus
Protocol independent
Suitable for supervision software
Similiar
Products
For others Converter / Adapter:
RS232 / RS485
See also the following link:
www.adfweb.com?Product=HD67118
USB / RS485
See also the following link:
www.adfweb.com?Product=HD67119
SCADA/HMI and the connection to a Personal Computer
Automated control of the line directions
Easy to use software configuration
Compatible with: Windows 98/ME/2000/XP
ADFweb.com Srl – IT31010 – Mareno – Treviso
Do you have an your customer protocol?
See the following link:
www.adfweb.com?Product=HD67003
Do you need to choose a device? do you want help?
Ask it to the following link:
www.adfweb.com?Cmd=helpme
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 2 of 15
Industrial Electronic Devices
INDEX:
INDEX
UPDATED DOCUMENTATION
REVISION LIST
WARNING
TRADEMARKS
SECURITY ALERT
CHARACTERISTICS
POWER SUPPLY
SOME EXAMPLES
CONNETION SCHEME
SET-UP OF THE DEVICE
REMOTE COM PORT
TUNNEL POINT TO POINT
TUNNEL POINT TO MULTIPOINT (MASTER SIDE)
TUNNEL POINT TO MULTIPOINT (SLAVE SIDE)
CHARACTERISTICS OF THE CABLES
MECHANICAL DIMENSIONS
ORDER CODE
ACCESSORIES
DISCLAIMER
OTHER REGULATIONS AND STANDARDS
WARRANTIES AND TECHNICAL SUPPORT
RETURN POLICY
PRODUCTS AND RELATED DOCUMENTS
UPDATED DOCUMENTATION:
Page
2
2
2
2
2
3
4
4
5
6
7
8
9
10
11
12
13
13
13
14
14
15
15
15
Dear customer, we thank you for your attention and we remind you that you
need to check that the following document is:
Updated
Related to the product you own
To obtain the most recently updated document, note the “document code” that
appears at the top right-hand corner of each page of this document.
With this “Document Code” go to web page www.adfweb.com/download/ and
search for the corresponding code on the page. Click on the proper “Document
Code” and download the updates.
To obtain the updated documentation for the product that you own, note the
“Document Code” (Abbreviated written "Doc. Code" on the label on the product)
and download the updated from our web site www.adfweb.com/download/
REVISION LIST:
Revision
Date
Author
Chapter
1.005
19/06/2005
Ddt
All
1.006
1.007
1.008
2.000
2.001
2.002
2.003
22/06/2007
26/06/2007
11/07/2007
12/07/2007
20/07/2009
5/07/2010
13/02/2013
Av
Av
Av
Av
Ml
FT
Nt
All
All
All
All
All
All
All
Description
documentation code
changed
Revision
Revision
accessories code changed
New document format
Revision
Revision
Added new chapters
WARNING:
ADFweb.com reserves the right to change information in this manual about our
product without warning.
ADFweb.com is not responsible for any error this manual may contain.
TRADEMARKS:
All trademarks mentioned in this document belong to their respective owners.
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 3 of 15
Industrial Electronic Devices
SECURITY ALERT:
GENERAL INFORMATION
To ensure safe operation, the device must be operated according to the instructions in the manual. When using the device are required for
each individual application, legal and safety regulation. The same applies also when using accessories.
INTENDED USE
Machines and systems must be designed so the faulty conditions do not lead to a dangerous situation for the operator (i.e. independent limit
switches, mechanical interlocks, etc.).
QUALIFIED PERSONNEL
The device can be used only by qualified personnel, strictly in accordance with the specifications.
Qualified personnel are persons who are familiar with the installation, assembly, commissioning and operation of this equipment and who
have appropriate qualifications for their job.
RESIDUAL RISKS
The device is state of the art and is safe. The instrument can represent a potential hazard if they are inappropriately installed and operated
by personnel untrained. These instructions refer to residual risks with the following symbol:
This symbol indicates that non-observance of the safety instructions is danger for people to serious injury or death and / or the
possibility of damage.
CE CONFORMITY
The declaration is made by us. You can send an email to [email protected] or give us a call if you need it.
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 4 of 15
Industrial Electronic Devices
CHARACTERISTICS:
Ethernet to RS232/RS485 is a professional device for using COM port through Ethernet line.
This device allows the following configurations:
Remote COM Port;
Tunnel Point to Point (Ethernet bridge for a serial line);
Tunnel Point to Multipoint (typical 485 connection with Master and slaves, but through Ethernet line ).
This device can be provided, on request, with a specific software, it can be a gateway for special serial protocol (HD67148):
Galvanic isolation between Ethernet and RS485;
Rail DIN;
Ethernet 10/100 Auto-sensing;
MAX Baud Rate 115.200 bps (RS485 side);
Temperature range -40°C to 85°C;
EMS
EN 61000-6-2.
POWER SUPPLY:
Recommended Power
Supply
VDC
VAC
24v
Caution: Not reverse the polarity power.
12v
VDC
VAC
Vmin
Vmax
Vmin
Vmax
8v
35v
8v
19v
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 5 of 15
Industrial Electronic Devices
SOME EXAMPLES:
Figure 1: Some examples
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 6 of 15
Industrial Electronic Devices
CONNECTION SCHEME:
Figure 2: Connection scheme for HD67120
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 7 of 15
Industrial Electronic Devices
SET-UP OF THE DEVICE:
ADFweb.com supplies the SW67120 software for the configuration of the device.
The software is downloadable on the site: http://www.adfweb.com/home/download/download.asp
(This manual is referenced to the last version of the software present on our web site).
Connect the RS232 cable from your personal computer to the device at the RS232 port.
Put the jumper on the enabled RS232 (see Figure 2).
When launching the SW67120 the “Select Modality” window appears (Fig. 3):
The following modalities are available:
“Remote COM Port”;
“Tunnel Point to Point”;
“Tunnel Point to Multipoint”.
Figure 3: “Select Modality” window
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 8 of 15
Industrial Electronic Devices
REMOTE COM PORT:
It consists in a configuration in which the device is generally controlled by a PC that is
connected using the protocol of the TCP line on the 10001 port. It writes bytes that
automatically are sent on serial line and each byte read from the serial port is
transmitted through the line to the connected PC.
The address of the device line and the serial line parameters must be set in the setting
window (Fig. 4) which relates to this mode.
The means of the fields for “EtherNet to RS232/485 LAN config” are:
In the field “IP” the IP address of the converter is defined;
In the field “SubNet Mask” the Subnet Mask of the converter is defined;
In the field “Port” the Port of the converter is defined.
The means of the fields for “Serial Port Setup” are:
In the field “Baud Rate” the velocity of the serial port is
defined;
In the field “Parity” the parity of the serial port is defined;
In the field “Stop Bits” the number of stop bits is defined. You can choose
between “1” and “2”;In the field “Flow Control” you can choose the flow control
among “none", "XON/XOFF", "CTS/RTS" or "XON/XOFF pass".
If the field “Use Gateway” in the “Gateway” section is checked it is possible to insert the
IP Address of the gateway in the field below.
In the field “COM port setup” you can select the COM port.
Figure 4: “Remote COM port” window
Once the parameters are set-up, configure the serial port to be used, push the download
button, perform a cycle of power-on and wait for the software to complete the proper
set-up.
Figure 4: “Remote COM port” window
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 9 of 15
Industrial Electronic Devices
TUNNEL POINT TO POINT:
It is a mode that allows the extension of a serial line, using a LAN line. The
two devices in this mode must be configured in a coherent way between the
two, or in such a way that both read the IP address of the other one. This
mode allows exchanges of packets with UDP protocol.
The address of the device line and the serial line parameters must be set in
the setting window (Fig. 5) which relates to this mode.
The means of the fields for “EtherNet to RS232/485 LAN config” are:
In the field “IP” the IP address of the converter is defined;
In the field “SubNet Mask” the Subnet Mask of the converter is defined;
In the field “Port” the Port of the converter is defined.
The means of the fields for “Serial Port Setup” are:
In the field “Baud Rate” the velocity of the serial port is
defined;
In the field “Parity” the parity of the serial port is defined;
In the field “Stop Bits” the number of stop bits is defined. You can
choose between “1” and “2”;
In the field “Flow Control” you can choose the flow control among
“none", "XON/XOFF", "CTS/RTS" or "XON/XOFF pass".
If the field “Use Gateway” in the “Gateway” section is checked it is possible to
insert the IP Address of the gateway in the field below.
In the field “Remote IP” for “Tunneling” it is necessary to insert the IP address
of the remote device in this mode in addition to the set-up of the device’s line.
In the field “COM port setup” you can select the COM port.
Once the parameters are set-up, configure the serial port to be used, push the
download button, perform a cycle of power-on and wait for the software to
complete the proper set-up.
ADFweb.com Srl – IT31010 – Mareno – Treviso
Figure 5: “Tunnel Point to Point” window
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 10 of 15
Industrial Electronic Devices
TUNNEL POINT TO MULTIPOINT (MASTER SIDE):
This mode allows a serial line to be extended into sections, using a LAN line,
where the device is on the side of the one that controls the line as Master and
the others are on the client’s side.
In order to configure a device as Master the field “Master Side” must be
checked. In the case of the master, it is not necessary to provide any other
address because the packets are sent as broadcasts.
The address of the device line and the serial line parameters must be set in
the setting window (Fig. 6) which relates to this mode.
The means of the fields for “MASTER LAN CONFIG” are:
In the field “IP” the IP address of the converter is defined;
In the field “SubNet Mask” the Subnet Mask of the converter is defined;
In the field “Port” the Port of the converter is defined.
The means of the fields for “Serial Port Setup” are:
In the field “Baud Rate” the velocity of the serial port is
defined;
In the field “Parity” the parity of the serial port is defined;
In the field “Stop Bits” the number of stop bits is defined. You can
choose between “1” and “2”;
In the field “Flow Control” you can choose the flow control among
“none", "XON/XOFF", "CTS/RTS" or "XON/XOFF pass".
If the field “Use Gateway” in the “Gateway” section is checked it is possible to
insert the IP Address of the gateway in the field below.
In the field “COM port setup” you can select the COM port.
Once the parameters are set-up, configure the serial port to be used, push the
download button, perform a cycle of power-on and wait for the software to
complete the proper set-up.
ADFweb.com Srl – IT31010 – Mareno – Treviso
Figure 6: “Tunnel Point to Multipoint (Master Side)” window
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 11 of 15
Industrial Electronic Devices
TUNNEL POINT TO MULTIPOINT (SLAVE SIDE):
For configure a device as Slave the field “Master Side” of “Operating Modality”
section should not be checked. In the case of the slave it is necessary to
provide the IP address of the Master Converter.
The address of the device line and the serial line parameters must be set in the
setting window (Fig. 5) which relates to this mode.
The means of the fields for “CLIENT LAN CONFIG” are:
In the field “IP” the IP address of the converter is defined;
In the field “SubNet Mask” the Subnet Mask of the converter is defined;
In the field “Port” the Port of the converter is defined.
The means of the fields for “Serial Port Setup” are:
In the field “Baud Rate” the velocity of the serial port is
defined;
In the field “Parity” the parity of the serial port is defined;
In the field “Stop Bits” the number of stop bits is defined. You can
choose between “1” and “2”;
In the field “Flow Control” you can choose the flow control among
“none", "XON/XOFF", "CTS/RTS" or "XON/XOFF pass".
If the field “Use Gateway” in the “Gateway” section is checked it is possible to
insert the IP Address of the gateway in the field below.
In the field “Remote IP” for “MASTER IP” it is necessary to insert the IP
address of the remote device in this mode in addition to the set-up of the
device’s line.
In the field “COM port setup” you can select the COM port.
Once the parameters are set-up, configure the serial port to be used, push the
download button, perform a cycle of power-on and wait for the software to
complete the proper set-up.
ADFweb.com Srl – IT31010 – Mareno – Treviso
Figure 7: “Tunnel Point to Multipoint (Slave Side)” window
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 12 of 15
Industrial Electronic Devices
CHARACTERISTICS OF THE CABLES:
The connection with the Ethernet socket must be with a Ethernet Cable with a RJ45 Plug.
It is recommended that the RS232 Cable not exceed 15 meters.
a)
b)
Figure 8: RS232 cabling configuration
For RS232 communication without flow control and for configure the device, use the cabling configuration illustrated in fig. 7 a.
For RS232 communication with flow control and for configure the device, use the cabling configuration illustrated in fig. 7 b.
The connection with the RS485 socket must be done with a twisted and shielded cable.
The terminal resistor must be inserted when the HD67120 is at the end of the line, using the Terminator jumper.
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 13 of 15
Industrial Electronic Devices
MECHANICAL DIMENSIONS:
Figure 9: Mechanical dimensions scheme
ORDER CODE:
Order Code: HD67120
-
RS232 / RS485 / Ethernet - Converter
Order Code: AC34001
-
Rail DIN - Power Supply 220/240V AC 50/60Hz – 12 V AC
Order Code: AC34002
-
Rail DIN - Power Supply 110V AC 50/60Hz – 12 V AC
Order Code: AC34104
-
European Input - Power Supply 230V AC 50Hz – 12 V DC
ACCESSORIES:
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 14 of 15
Industrial Electronic Devices
DISCLAIMER
All technical content within this document can be modified without notice. The content of the document content is a recurring audit.
For losses due to fire, earthquake, third party access or other accidents, or intentional or accidental abuse, misuse, or use under abnormal
conditions repairs are charged to the user. ADFweb.com S.r.l. will not be liable for accidental loss of use or inability to use this product, such
as loss of business income. ADFweb.com S.r.l. shall not be liable for consequences of improper use.
OTHER REGULATIONS AND STANDARDS
WEEE INFORMATION
Disposal of old electrical and electronic equipment (as in the European Union and other European countries with separate
collection systems).
This symbol on the product or on its packaging indicates that this product may not be treated as household rubbish. Instead, it
should be taken to an applicable collection point for the recycling of electrical and electronic equipment. If the product is disposed
correctly, you will help prevent potential negative environmental factors and human health, which could otherwise be caused by
inappropriate disposal. The recycling of materials will help to conserve natural resources. For more information about recycling this
product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
RESTRICTION OF HAZARDOUS SUBSTANCES DIRECTIVE
The device respects the 2002/95/EC Directive on the restriction of the use of certain hazardous substances in electrical
and electronic equipment (commonly referred to as Restriction of Hazardous Substances Directive or RoHS).
CE MARKING
The product conforms with the essential requirements of the applicable EC directives.
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
User to RS232 / RS485 / Ethernet
Document code: MN67120_ENG
Revision 2.003
Page 15 of 15
Industrial Electronic Devices
WARRANTIES AND TECHNICAL SUPPORT:
For fast and easy technical support for your ADFweb.com SRL products, consult our internet support at www.adfweb.com.
Otherwise contact us at the address [email protected]
RETURN POLICY:
If while using your product you have any problem and you wish to exchange or repair it, please do the following:
1) Obtain a Product Return Number (PRN) from our internet support at www.adfweb.com. Together with the request, you need to provide detailed information
about the problem.
2) Send the product to the address provided with the PRN, having prepaid the shipping costs (shipment costs billed to us will not be accepted).
If the product is within the warranty of twelve months, it will be repaired or exchanged and returned within three weeks. If the product is no longer under warranty,
you will receive a repair estimate.
PRODUCTS AND RELATED DOCUMENTS:
Part
Description
URL
HD67118
Converter RS232 to RS485 Isolated
www.adfweb.com?Product=HD67118
HD67119
Converter USB 2.0 to RS485 Isolated
www.adfweb.com?Product=HD67119
HD67507
Gateway Modbus TCP Server to RTU Master
www.adfweb.com?Product=HD67507
HD67510
Gateway Modbus TCP Client to RTU Slave
www.adfweb.com?Product=HD67510
ADFweb.com Srl – IT31010 – Mareno – Treviso
INFO: www.adfweb.com
Phone +39.0438.30.91.31
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement