IS5300 User Manual
324 Port InfiniBand QDR Switch Platform
Hardware User Manual
PN: MIS5300
Rev 1.8
www.mellanox.com
Rev 1.8
NOTE:
THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY KIND
AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE
THE PRODUCTS IN DESIGNATED SOLUTIONS. THE CUSTOMER'S MANUFACTURING TEST ENVIRONMENT HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE
PRODUCTO(S) AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOX TECHNOLOGIES CANNOT
AND DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST
QUALITY. ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD
PARTIES FOR ANY DIRECT, INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF
ANY KIND (INCLUDING, BUT NOT LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) AND RELATED DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Mellanox Technologies
350 Oakmead Parkway Suite 100
Sunnyvale, CA 94085
U.S.A.
www.mellanox.com
Tel: (408) 970-3400
Fax: (408) 970-3403
Mellanox Technologies, Ltd.
PO Box 586 Hermon Building
Yokneam 20692
Israel
Tel: +972-4-909-7200
Fax: +972-4-959-3245
© Copyright 2011. Mellanox Technologies. All rights reserved.
Mellanox®, BridgeX®, ConnectX®, CORE-Direct®, InfiniBlast®, InfiniBridge®, InfiniHost®, InfiniRISC®, InfiniScale®, InfiniPCI®,
PhyX®, Virtual Protocol Interconnect and Voltaire are registered trademarks of Mellanox Technologies, Ltd.
FabricIT™, MLNX-OS™, and SwitchX™ are trademarks of Mellanox Technologies, Ltd. All other marks and names mentioned herein
may be trademarks of their respective companies.
QDR InfiniBand Switch Platform Hardware User Manual
2
Mellanox Technologies
Document Number: 3240
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Table of Contents
Table of Contents
3
Table of Figures
5
Table of Lists
7
Revision History
8
About this Manual
9
Intended Audience
Related Documentation
Conventions
Chapter 1
Chapter 2
Chapter 3
Chapter 4
Chapter 5
9
9
9
Overview
11
1.1 Product Information
1.1.1 Serial Number and Product Version Information
1.1.2 Management Module MAC
1.2 Features List
11
11
12
15
Hardware
16
2.1 LED Status Indicators
2.1.1 Power Supply Unit LEDs
2.1.2 Leaf Board LED Indicators
2.1.3 Spine Board LED Indicators
2.1.4 Spine Side Panel Display LED Indicators
2.1.5 Management Module LED Indicators
2.1.6 Port Connector Interfaces
2.2 Air Flow
2.3 QSFP Cable Power Budget Classification
2.4 Management Module Interfaces
2.4.1 I2C
2.4.2 CONSOLE
2.4.3 MGT– Management
2.4.4 USB
2.4.5 Reset – RST
20
20
21
23
24
26
26
27
27
27
28
28
28
28
28
Installation
30
3.1
3.2
3.3
3.4
3.5
Environmental and Safety Recommendations
Chassis Package Contents
Leaf Package Contents
Management Package Contents
Physical Installation
3.5.1 Starting with the Rack
3.5.2 ESD Connection
3.5.3 Installation Procedure
3.5.4 Installing the Cable Holder
3.5.5 Ground Connections
3.6 Power Connections
3.6.1 Powering Up the Switch Platform
3.7 InfiniBand QSFP Cable Installation
3.7.1 Cable Power Classes
30
31
32
32
32
33
34
34
52
53
54
54
55
56
Chassis Power Up
57
4.1 Power Supply and Spine Board Indicator Status at Power ON
57
Insertion and/or Hotswap Extraction
59
Mellanox Technologies
3
Rev 1.8
5.1
5.2
5.3
5.4
5.5
5.6
Chapter 6
Chapter 7
Chapter 8
Power Supply Units
5.1.1 Extracting and Inserting the Power Supply Unit
Leaf Boards
5.2.1 Extracting a Leaf Board
5.2.2 Inserting a Leaf Board
Spine Boards
5.3.1 Extracting a Spine Board
5.3.2 Inserting a Spine Board
Fan Modules
5.4.1 Leaf Fan Module
5.4.2 Spine Fan Modules
Management Module
5.5.1 Extracting a Management Module
5.5.2 Inserting a Management Module
Switch Shut Down Procedures
5.6.1 To shut down the chassis run the following command twice:
5.6.2 To shut down a leaf run the following command:
5.6.3 To shut down a spine run the following command:
59
59
61
61
62
62
62
63
64
64
65
66
66
67
68
68
68
68
Disassembly and Disposal
69
6.1 Disassembling the Chassis
6.1.1 Removing the Chassis
6.1.2 Removing the Bottom Shelf
6.2 Disposal
69
69
70
71
Switch Management Tools
72
7.1
7.2
7.3
7.4
73
73
74
74
InfiniBand Subnet Manager
Fabric Diagnostics with UFM Diag
Accessing the CPU via the Ethernet Connector
Upgrading Software
TroubleShooting
75
8.1 Power Supply Unit
8.2 Leaf Board
8.3 Management Module
8.3.1 Yellow Status LED (for the Chassis) on the Management Module is Lit
8.3.2 Yellow LED for the Leaf Fan on the Management Module is Lit
8.3.3 Yellow LED for the Spine Fan on the Management Module is Lit
8.4 Spine Board
8.5 FabricIT SW
75
75
76
76
76
77
77
77
Appendix A Specification Data
79
A.1 Specifications
A.2 EMC Certifications
79
81
Appendix B Calculating the Weight of a Customized Chassis
82
Appendix C Calculating the Power of a Customized Chassis
83
Appendix D QSFP Interface
84
Appendix E Replacement Parts Ordering Numbers
86
Appendix F Avertissements de sécurité d’installation (French)
88
Appendix G Installation - Sicherheitshinweise (German)
91
Appendix H Advertencias de seguridad para la instalación (Spanish)
94
4
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Table of Figures
Figure 1:
Generic Product Label
12
Figure 2:
Product Label Tab Location
12
Figure 3:
Management Module MAC Address Location
12
Figure 4:
S5300 Switch Views
14
Figure 5:
Power Supply Unit Status Indications
20
Figure 6:
PSU Cover On and Off
21
Figure 7:
Leaf Board Led Indicators
21
Figure 8:
Spine Status LEDs
23
Figure 9:
Spine Side Panel Display Status Indications
25
Figure 10: Management Module Status Indications
26
Figure 11: Port Numbering
27
Figure 12: Top and Bottom Ports
27
Figure 13: Management Module Interfaces
27
Figure 14: Reset Button
29
Figure 15: Distance Between the Vertical Supports
34
Figure 16: Installation Kit Parts
36
Figure 17: Container Screws
37
Figure 18: Vertical Rack Supports Dimension
39
Figure 19: Adjustable Shelf Brackets
39
Figure 20: Top of Shelf Bracket
40
Figure 21: Placing the Shelf Bracket
40
Figure 22: Caged Nut Locations for the Shelf Brackets
41
Figure 23: Shelf Brackets
41
Figure 24: Place the Lock-Down Bar on the Shelf
42
Figure 25: U Numbering Above Shelf
43
Figure 26: Putting the Chassis in the Rack
44
Figure 27: Location for the Lock-down Bar
44
Figure 28: Place the Upper Bracket Offset
45
Figure 29: Attach the Shelf Extension
45
Figure 30: Caged Nut Placement by U Numbers
46
Figure 31: Fork Lift
47
Figure 32: Face Plate Mounting Bolt Locations
47
Figure 33: Upper Brackets and Offset Location
48
Figure 34: Upper Bracket Installation
49
Mellanox Technologies
5
Rev 1.8
Figure 35: Offset to Upper bracket Bolts
50
Figure 36: Lock-Down Bar
50
Figure 37: Bolt and Washer Order
51
Figure 38: Cable Holder
52
Figure 39: Ground Connection
53
Figure 40: Multiple Power Inlets - Electric Caution Notification
55
Figure 41: Spine Module
55
Figure 42: Top and Bottom Ports
56
Figure 43: Spine Side Panel Display Status Indications
58
Figure 44: Management Module Status Indications for Normal Operation
58
Figure 45: Power Cord Top Bar
60
Figure 46: Power Supply
60
Figure 47: Ejector Latch
61
Figure 48: Leaf Release
62
Figure 49: Ejector Latch
63
Figure 50: Spine Board Extraction
63
Figure 51: Fan Locations on the Chassis
64
Figure 52: Leaf Fan Module Extraction
65
Figure 53: Spine Fan Module
65
Figure 54: Fan Status LED on the Spine Module
66
Figure 55: Ejector Latch
67
Figure 56: Management Module
67
Figure 57: Mechanical Lifting Device
70
Figure 58: QSFP Connector Male and Female Views
85
6
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Table of Lists
Table 1:
Revision History of this User’s Manual
8
Table 2:
Reference Documents and Web Sites
9
Table 3:
Switch Rack Mechanical and Environmental Requirements (Fully Populated Chassis) 13
Table 4:
Leaf Status LED
21
Table 5:
Bad Port LED Configurations
22
Table 6:
Connector Physical and Logical Link Indications
22
Table 7:
Spine Status LED
23
Table 8:
Spine to Leaf IB Link Status
24
Table 9:
Spine Fan Status LED
24
Table 10:
Spine to Leaf IB Connection Status LEDs
24
Table 11:
LEDs Display for Normal Operation
25
Table 12:
LEDs Display for Normal Operation
26
Table 13:
Switch Specification Sheet IS5300
79
Table 14:
Power Consumption of Chassis Parts
83
Table 15:
InfiniBand QSFP Connector Pinout
84
Table 16:
Replacement Parts Ordering Numbers
86
Mellanox Technologies
7
Rev 1.8
Revision History
Table 1 - Revision History of this User’s Manual
Revision
8
Date
Details
1.8
July, 2011 Changes to Reset button section.
Changes to installtion kit parts and procedure.
Changed name to Hardware User Manual
1.7
May, 2011 Removed “InfiniBand Fabric Initialization and Management”
Updated Fabric Management Software Section
1.6
Jan. 2011 Added lock washer and flat washer positions for the lock down bar bolts.
1.5
Nov. 2010 Added New KCC statement
1.4
Oct. 2010 Added air flow direction
1.3
Oct. 2010 Added procedure step to screw in 9 screws through the offset into the upper
bracket.
Fixed Port Connector LED Assignment.
1.2
July 2010 Added QSFP Cable Power Budget Classification
Added weight lifting warning
Added “Remove all protective plastic film from all sides and top of the chassis.”
Added FCC Statement 15.19
Added CoG and Max Heat to the Specs in Appendix A
1.1
July 2010 Fixed chassis height on page 10.
1.0
July 2010 Initial release
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
About this Manual
This manual provides an overview of the IS5300 modular InfiniBand chassis switch and guidelines for its operation.
Intended Audience
This manual is intended for users and system administrators responsible for installing and setting
up the chassis platform.
The manual assumes familiarity with the InfiniBand® architecture specification.
Related Documentation
The documentation set accompanying the QSFP Chassis InfiniBand Switch platform includes the
following:
Table 2 - Reference Documents and Web Sites
FabricIT Enterprise Fabric Management Software See
http://www.mellanox.com > Products > Management Software
CLI User’s Manual
Select "FabricIT EFM - InfiniBand Fabric Management"Click
"Software and Documentation Download center" select User
Manual
Switch Hardware Installation Guide
Each Mellanox Technologies’ switch platform is shipped with an
Installation Guide document that contains instructions for Installation in a rack and initialization of the switch platform.
IB Switch Platforms Embedded Management Tools Describes the Embedded Management Tools (EMGT) package,
which provides Out-of-Band management capabilities for
Document no. 2141UM
InfiniBand switches.
Available from http://docs.mellanox.com (requires a Mellanox
Technologies customer account).
Switch Firmware and Firmware Update Tools
See
http://www.mellanox.com/content/
pages.php?pg=management_tools&menu_section=34
Note that the Switch System described in this manual is based on
Mellanox Technologies’ InfiniScale® IV switch device.
Unified Fabric Manager™ (UFM™)
The user manual can be downloaded together with the software
package upon license purchase
Conventions
Throughout this manual, the name IS5300 and the term switch are used to describe the 324 port
QSFP InfiniBand chassis, unless explicitly indicated otherwise.
Mellanox Technologies
9
Rev 1.8
The following pictures are used throughout this document to indicate information that is important
to the user.
This symbol makes recommendations to the user.
This symbol indicates information that is helpful to the user.
This symbol indicates a situation that can potentially cause damage to hardware or software.
BEWARE! This symbol indicates a situation that can potentially cause personal injury or
damage to hardware or software.
10
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
1
Rev 1.8
Overview
This User Manual provides an overview of the IS5300 QSFP Modular InfiniBand Switch Platform
(known in this document as ‘the switch’) and its operational environment.
Mellanox IS5300 switch system provides the highest performing fabric solution by delivering high
bandwidth and low latency to Enterprise Data Centers (EDC), High-Performance Computing
(HPC) and Embedded environments. Networks built with the IS5300 system can carry converged
traffic with the combination of assured bandwidth and granular quality of service. Built with Mellanox’s 4th generation InfiniScale® IV InfiniBand switch device, IS5300 systems provide up to
40Gb/s full bidirectional bandwidth per port. With up to 324 ports in a 17U high form factor, these
systems are among the densest switching systems available.
The switch platform comes pre-installed with all necessary firmware for standard operation within
an InfiniBand fabric and requires an InfiniBand compliant Subnet Manager running from one of
the hosts or the management module of the switch system. An initial configuration procedure
should be followed to initialize the switch before connecting it to the network after which normal
operation can proceed. (See the installation guide for details regarding the initial configuration)
Once connected to the network, the Subnet Management software automatically discovers and
configures the fabric and begins utilizing the switch.
It is recommended that the Mellanox OpenFabrics software package be installed on all nodes connected to the switch. The software package provides a subnet manager and network management
tools as well as connectivity software for servers and storage, and is available on the Mellanox
web site.
Basic installation is covered in Chapter 3, “Installation” on page 30.
Hot-swapping components and hardware maintenance is covered in Chapter 5, “Insertion and/
or Hotswap Extraction” on page 59.
1.1
Product Information
1.1.1 Serial Number and Product Version Information
The serial number, GUID Identifier and product version information are found on the label that is
attached to the pull-out tab that is below the Mellanox logo on the spine side of the chassis.
FabricIT-CM license is located on the bottom side of the pull out tab.
Mellanox Technologies
11
Rev 1.8
Overview
Figure 1: Generic Product Label
S/N:MT0949X00147
REV: X1
P/N: MIS5300Q – 6DNC
GUID: 0002C902004157B0
Made in IL
This is the System Image GUID according to the IB spec. It is burned on the board which is in the
chassis. All the boards and the management SW look for this GUID in addition to their own Node
GUID.
Figure 2: Product Label Tab Location
F1
F2
Top right hand side of the
spine side of the chassis
Tab location with
Product label and
management MAC
IS5300
Mellanox
IS5300
S1
IS5300
Mellanox
S2
1.1.2 Management Module MAC
Each management module has a label with its MAC address. See below for the location of this
label.
Figure 3: Management Module MAC Address Location
I2C
CONSOLE
MGT
RST
PSU
S.FANS L.FANS MASTER
MGT MAC:
00:02:C9:11:34:8A
MAC address location
12
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Product Physical Specifications and Power
Table 3 - Switch Rack Mechanical and Environmental Requirements (Fully Populated Chassis)
Rack
Height
Required
17U
(755 mm)
16 U for the
chassis and
1U for the
shelf
Rack Width
19” (EIA310)
(482.6 mm)
Rack
Depth
25.7”
685 mm
# of leafs
/
# of Spines
18/9
Weight
Max. Power (648 x QSFP Ports)
212.36 kg (468 lbs) full Typical: 3919.80W (including
configuration
QSFP active cables at 2W)
Typical: 3595.80W (including
90 kg (199 lbs) empty QSFP active cables at 1W)
Typical: 3090.43W (passive
configuration
cables)
Up to 6 Power Supplies of 100240VAC, 50-60Hz, 6.3-13A
Ambient
Temp.
Max: 45ºC
Min: 10ºC
The switch ships in a minimum base configuration plus additional modules depending on the chosen customer configuration. Optional modules include:
•
Leaf boards
•
Management modules
Figure 4 shows the connector and spine sides fully populated.
Mellanox Technologies
13
Rev 1.8
Overview
Figure 4: S5300 Switch Views
AC1
AC2
I2C
CONSOLE MGT
I2C
F1
F2
IS5300
Mellanox
IS5300
S1
IS5300
IS5300
Mellanox
S2
P1
S3
Mellanox
P2
S4
S5
P3
S6
P4
S7
S8
P6
P5
S9
14
Mellanox Technologies
AC3
AC4
AC5
RST PSU S.Fans L.Fans Master
CONSOLE MGT
RST PSU S.Fans L.Fans Master
AC6
324 Port InfiniBand QDR Switch Platform Hardware User Manual
1.2
Rev 1.8
Features List
•
324 QDR (40Gb/s) ports in a 29U switch
•
IBTA 1.21 compliant
•
SDR/DDR/QDR link speed
•
Congestion control
•
Adaptive routing
•
Port mirroring
•
Chassis High Availability
•
sMB High Availability
Mellanox Technologies
15
Rev 1.8
2
Hardware
Hardware
Installation Safety Warnings
1. Installation Instructions
Read all installation instructions before connecting the equipment to the power source.
2. Bodily Injury Due to Weight
Use enough people to safely lift this product.
<40 lbs
<18 kgs
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
3. Installation in Restricted Access Location.
This unit is intended for installation in Restricted Access Location.
4. Over-temperature
This equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended: 45°C (113°F). Moreover, to guarantee proper air
flow, allow at least 8cm (3 inches) of clearance around the ventilation openings.
5. Stacking the Chassis
The chassis should not be stacked on any other equipment. If the chassis falls, it can
cause bodily injury and equipment damage.
6. Redundant Power Supply Connection - Electrical Hazard
This product includes a redundant power or a blank in its place. In case of a blank
power supply, do not operate the product with the blank cover removed or not securely
fastened.
16
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
7. During Lightning - Electrical Hazard
During periods of lightning activity, do not work on the equipment or connect or disconnect cables.
8. Copper InfiniBand Cable Connecting/Disconnecting
Copper InfiniBand cables are heavy and not flexible, as such they should be carefully
attached to or detached from the connectors. Refer to the cable manufacturer for special warnings/instructions.
9. Rack Mounting and Servicing
When this product is mounted or serviced in a rack, special precautions must be taken
to ensure that the system remains stable. In general you should fill the rack with equipment starting from the bottom to the top.
10. Equipment Installation
This equipment should be installed, replaced, and/or serviced only by trained and qualified personnel.
11. Proper Enclosure
A suitable electrical, mechanical and fire enclosure shall be provided by the end product manufacturer and or the end user.
12. Equipment Disposal
Disposal of this equipment should be in accordance to all national laws and regulations.
13. Local and National Electrical Codes
This equipment should be installed in compliance with local and national electrical
codes.
Mellanox Technologies
17
Rev 1.8
Hardware
14. UL Listed and CSA Certified Power Supply Cord Leakage >3.5mA
For North American power connection, select a power supply cord that is UL Listed
and CSA Certified, 3 - conductor, [16 AWG], terminated with a molded plug rated at
125 V, [13 A], with a minimum length of 1.5m [six feet] but no longer than 4.5m.
For European connection, select a power supply cord that is internationally
harmonized and marked “<HAR>”, 3 - conductor, minimum 1.0 mm2 wire,
rated at 300 V, with a PVC insulated jacket. The cord must have a molded plug
rated at 250 V, 10 A.
Warning: High leakage current; Earth connection essential before connecting supply.
15. Add GND connection information
Before connecting this device to the power line, the protective earth terminal screws of
this device must be connected to the protective earth in the building installation.
(GND Connection Information):
The building installation shall provide a means for connection to protective earth; and
the equipment shall to be connected to that means permanently by a service person.
A SERVICE PERSON shall check whether or not the socket - outlet from which the
equipment is to be powered provides a connection to the building protective earth. If
not, the SERVICE PERSON shall arrange for the installation of a PROTECTIVE
EARTHING CONDUCTOR from the separate protective earthing terminal to the protective earth wire in the building. The equipment shall be installed in area where equipotential bonding exists ((such as a telecommunication centre or a dedicated computer
room)
16. Installation codes
This device must be installed according to the latest version of the country national
electrical codes. For North America, equipment must be installed in accordance to the
applicable requirements in the US National Electrical Code and the Canadian Electrical Code.
17. Interconnection of units
Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL certified
type DP-1 or DP-2. (Note- when residing in non LPS circuit)
Overcurrent Protection: A readily accessible Listed branch circuit overcurrent protective device rated 20 A must be incorporated in the building wiring.
18. Hazardous Radiation Exposure
Caution – Use of controls or adjustment or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
18
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
CLASS 1 LASER PRODUCT and reference to the most recent laser standards:
IEC 60825-1:2007/03 and EN 60825-1:2007
19. Do Not Use the Switch as a Shelf or Work Space.
Caution: Slide/rail mounted equipment is not to be used as a shelf or a work space.
20. WEEE Directive
According to the WEEE Directive 2002/96/EC, all waste electrical and electronic
equipment (EEE) should be collected separately and not disposed of with regular
household waste.
Dispose of this product and all of its parts in a responsible and environmentally
friendly way.
Mellanox Technologies
19
Rev 1.8
2.1
Hardware
LED Status Indicators
The LEDs are placed on the chassis for the convenience of the IT manager.
We recommend that all of the chassis sub systems be maintained and managed through
the management software.
2.1.1 Power Supply Unit LEDs
Each Power Supply Unit has the following indicator LEDs.
Figure 5: Power Supply Unit Status Indications
AC
DC
OK
FAIL
OK
AC – When lit this LED indicates input voltage between 100 and 240 Volts.
DC FAIL – When lit this LED indicates a fault in the power supply.
DC OK – When lit this LED indicates that the output from the power supply is +48 VDC.
The PSUs are on the spine side of the chassis behind two cover panels. The plugs for
these PSUs are on the leaf side of the chassis.
20
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 6: PSU Cover On and Off
F1
F1
F2
F2
IS5300
IS5300
Mellanox
Mellanox
IS5300
IS5300
S1
IS5300
IS5300
S1
Mellanox
OK
OK
AC
OK
FAIL
S2
S3
S3
P2
S4
S4
OK
S5
AC
OK
FAIL
DC
FAIL
AC
OK
S6
DC
P4
OK
S5
P3
AC
OK
P1
DC
FAIL
DC
Mellanox
S2
S6
S7
S7
S8
S8
OK
OK
FAIL
AC
OK
AC
OK
S9
DC
FAIL
S9
DC
P6
P5
2.1.2 Leaf Board LED Indicators
Figure 7: Leaf Board Led Indicators
1
2
3
4
5
6
7
8
9
10
UID
2.1.2.1
Status LED
Each leaf board has a Status LED on the far left of the leaf. This LED has the following meanings
according to the LED status.
The Leaf Status indicator LED
has the following led assignment:
Table 4 - Leaf Status LED
LED Description
Off
No power to the Leaf
Solid Green
Leaf is up and running
Flashing Green
Leaf is powering up
Orange
Non fatal error This color LED needs troubleshooting, but
does not require chassis shutdown.
Mellanox Technologies
21
Rev 1.8
Hardware
Table 4 - Leaf Status LED
LED Description
Red
2.1.2.2
Fatal error
Bad Port LED
The Bad Port indicator is located on the left side of the spine. The following Bad Port conditions
are possible:
Table 5 - Bad Port LED Configurations
LED Configuration
Description
Off
OK – All ports are up and running.
Flashing Orange
Error –One or possibly more ports has just received a symbol
error.
This LED shows symbol errors. Possible causes for this are:
•
bad cable
•
bad connection
•
bad connector
This LED lights up when one or more ports is receiving a symbol error. The LED immediately
goes off until the next symbol error is received.
2.1.2.3
UID LED Switch Identifier
The UID LED is a debug feature that will become available to customers in the near future. For
details please contact Mellanox Technologies support.
2.1.2.4
Leaf Board Port Connector LED Assignment
Above the ports are two LEDs one for the upper port
and one for the lower port
lowing table shows the port status according to the LED indication.
Table 6 - Connector Physical and Logical Link Indications
LED Description
22
Off
No power to the port
Solid Green
Logical link up
Flashing Green
Data activity
flashing speed ≈ data transfer speed
Orange
Physical link up
Flashing Orange
A problem with the physical link
Mellanox Technologies
. The fol-
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
The switch does not provide a visual means that indicates the port speed configuration
(SDR, DDR, QDR) and/or the link width (1X or 4X). The speed and link width configurations can be retrieved using management software.
2.1.3 Spine Board LED Indicators
Each leaf board is connected by links to each spine module. Each spine has one status LED for the
spine and 36 status LEDs. The 36 LEDs on each spine are divided by the number of leafs and the
result (X) is the number of ports from each leaf that is connected to the spine. 9 spines must be
installed and working to ensure that full BW exists between nodes. Should a leaf be removed then
X number of LEDs will turn off on each of the spines.
The status LEDs for the spine and their descriptions are shown in Table . The LEDs indicate as follows:
Figure 8: Spine Status LEDs
Status
1 3 5
7 9 11 13 15 17
19 21 23 25 27 29 31 33 35
Fan Status
2 4 6
Spine Status
2.1.3.1
8 10 12 14 16 18
Fan Status
20 22 24 26 28 30 32 34 36
Spine Leaf IB Connection Status
Status LED
The Spine Status indicator LED has the following led assignment:
Table 7 - Spine Status LED
LED Description
Off
No power to the spine
Solid Green
Spine is up and running
Flashing Green
Spine is powering up
Orange
Non fatal error
Red
Fatal error
The leaf board status on each spine displays the condition of the connection between the spine and
each leaf. There is a minimum of one LED per each leaf per each spine. Each spine has leaf status
LEDs. The leaf LEDs on each spine indicate as follows:
Mellanox Technologies
23
Rev 1.8
Hardware
The Spine to leaf board Status indicator LED has the following led assignment:
Table 8 - Spine to Leaf IB Link Status
LED Description
2.1.3.2
Off
Link is down
Solid Green
Logical connection
Flashing Green
Data activity
Orange
Physical connection
Fan LED
The Spine Fan indicator LED has the following led assignment:
Table 9 - Spine Fan Status LED
LED Description
2.1.3.3
Green
Spine Fan is OK
Yellow
One or more of the fans in this spine is not working
Each spine has two fans in the fan module.
Spine to Leaf IB Connection Status LEDs
These LEDs indicate a valid connection between a leaf and a spine.
The Spine to Leaf IB Connection Status LEDs have the following led assignment:
Table 10 - Spine to Leaf IB Connection Status LEDs
LED Description
Green
A valid connection exists between this spine and the numbered leaf.
Yellow
A valid connection does not exist between this spine and the
numbered leaf.
2.1.4 Spine Side Panel Display LED Indicators
The spine side panel display has LEDs that show the chassis condition.
24
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 9: Spine Side Panel Display Status Indications
STATUS
PSU
STATUS
SPINE
FANS
LEAF
FANS
MGT 1
STATUS
MGT 2
STATUS
Table 11 - LEDs Display for Normal Operation
LED
Description
Normal
State
STATUS
Off = No Power
Green
Green = System is up and running.
Yellow = System warning. Attention needed (such as overheating).
Red = System not operational (Diagnostics fail, CPU hang,
HW fail, Overheat-critical)
Blinking Yellow = System booting / Restore factory defaults in progress.
PSU STATUS
Off = No power
Green
Green = Normal operational
Red = PS fault detected. User should check individual power supplies for
fault indications.
SPINE FANS
STATUS
Off = No power to fan
Green = Nominal operational
Yellow = Non fatal failure
Red = Fatal failure Turn the chassis off and then troubleshoot
Green
LEAF FANS
STATUS
Off = No power to fan
Green = Nominal operational
Yellow = Non fatal failure
Red = Fatal failure Turn the chassis off and then troubleshoot
Green
MGT 1 STATUS Off = no power or this management module is not installed
Green
Green = Management module is operating as a master
Yellow = Management module is operating as a slave (i.e., the other management module is a master)
MGT 2 STATUS Off = no power or this management module is not installed
Yellow
Green = Management module is operating as a master
Yellow = Management module is operating as a slave (i.e., the other management module is a master)
Mellanox Technologies
25
Rev 1.8
Hardware
2.1.5 Management Module LED Indicators
Figure 10: Management Module Status Indications
I2C
CONSOLE
MGT
RST
PSU
S.FANS L.FANS MASTER
MGT MAC:
00:02:C9:11:34:8A
Status
The management module LEDs display the switch system operating conditions.
Table 12 - LEDs Display for Normal Operation
LED
Description
Normal
State
STATUS
This LED shows
the status of the
chassis.
Off = No Power
Green
Green = System is up and running.
Yellow = System warning. Attention needed (such as overheating).
Red = System not operational (Diagnostics fail, CPU hang,
HW fail, Overheat-critical)
Blinking Yellow = System booting / Restore factory defaults in progress.
PSU STATUS
Off = No power
Green
Green = Normal operational
Red = PS fault detected. User should check individual power supplies for
fault indications.
SPINE FANS
STATUS
Off = No power to fan
Green = Nominal operational
Yellow = Non fatal failure
Red = Fatal failure Turn the chassis off and then troubleshoot
Green
LEAF FANS
STATUS
Off = No power to fan
Green = Nominal operational
Yellow = Non fatal failure
Red = Fatal failure Turn the chassis off and then troubleshoot
Green
MASTER
Off = no power or this management module is not installed
Green
Green = Management module is operating as a master (i.e., the other
management module is a slave)
Yellow = Management module is operating as a slave (i.e., the other management module is a master)
2.1.6 Port Connector Interfaces
The connector side of the switch has 18 leaf boards and each leaf board has 18 QSFP ports. The
ports on each leaf board are placed in two rows, 9 ports to a row. The ports are labelled as shown in
Figure 11. The bottom row ports are flipped from the top row. See Figure 12.
26
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 11: Port Numbering
1
3
5
7
9
1 1
1 3
1 5
1 7
2
4
6
8
1 0
1 2
1 4
1 6
1 8
Figure 12: Top and Bottom Ports
2.2
Air Flow
These switches come with the air flow pattern of air entering through the spine side and exiting
through the connector side.
2.3
QSFP Cable Power Budget Classification
All IS5300 QSFP switches are designed for active cables with a max power per module of 2.0W.
This is power level 2 according to the QSFP Public Specification.
2.4
Management Module Interfaces
The switch system requires at least one management module. The management module has five
interfaces to connect to the IS5300. They are:
•
1 I2C port
•
1 CONSOLE port – this is an RS232 connector for connecting to a host machine
•
1 MGT – this is an Ethernet connector
•
1 USB port
•
1 RST – reset button
Figure 13: Management Module Interfaces
I2C
CONSOLE
MGT
RST
PSU
S.FANS L.
Mellanox Technologies
27
Rev 1.8
Hardware
2.4.1 I2C
This interface is for Debug and Troubleshooting only. This interface is for FAEs only.
2.4.2 CONSOLE
The CONSOLE port is used during the installation process to configure the chassis for remote
management. Connect this port to a local host using the harness supplied with the chassis. See the
Installation Guide for the initial configuration procedure.
2.4.3 MGT– Management
The MGT port is an Ethernet port for remote management. Any remote terminal connected to the
Ethernet can then be used to manage the fabric and chassis.
Each Ethernet connector gets connected to Ethernet switches. These switches must be
configured to 10M/100M auto-negotiation.
Initial configuration must be done on all of the management modules.
2.4.4 USB
The USB port can be used to upload new SW using any storage device that has a USB connector.
This interface is USB 2.0.
2.4.5 Reset – RST
The Reset button resets the chassis management module when the button is pushed. When the button is held down for 15 seconds the management module is reset and the password deleted.
DO NOT use a sharp pointed object such as needle or push pin for pressing the Reset
button. Sharp objects can cause damage, use a flat object such as a paper clip.
28
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 14: Reset Button
C
CONSOLE
MGT
RST
PSU
S.FANS L.FANS MASTER
This button resets the CPU of the management module. A quick push of this button performs this
reset. When the reset button is pushed on the master management module this management module is reset becoming the slave and the other management module becomes the master. If there is
only one management module in the chassis all of the leafs and ports are reset by bringing them
down and powering them up when the reset button is pushed. When the button is held down for 15
seconds the management module is reset and the password is deleted. You will then be able to
enter without a password and make a new password for the user admin.
Mellanox Technologies
29
Rev 1.8
3
Installation
Installation
This chassis can be installed in standard 19” racks that have depths between 65cm and
80cm between the vertical supports of the rack.
Installation and initialization of the chassis is a simple process requiring attention to the normal
mechanical, power, and thermal precautions for rack-mounted equipment. Your Chassis will be
shipped in two packages one with the all of the leafs (leaf package) that are ordered and an extra
management module should it be ordered, and the second package (chassis package) with all of the
rest of the parts.
The chassis requires initial configuration to get the chassis and Fabric management up and running
through remote management. See the Installation Guide that is packed in the box for the instructions to make the initial configuration.
This unit is intended for installation in a Restricted Access Location. A restricted
access area can be accessed only through the use of a special tool, lock and key, or
other means of security.
3.1 Environmental and Safety Recommendations
The following are Mellanox recommendations.
Recommended ambient temperature in the System room is 20o ± 5o C.
Recommended humidity ranges is 40% ± 15% without condensing.
It is highly recommended that the installation sites be as isolated as possible from all
sources of radio transmissions and electrical interference.
30
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
It is highly recommended that the installation site building be equipped with a lightning rod.
It is highly recommended that the installation site be equipped with smoke detectors
and a fire alarm warning system.
The system requires a KVA rated UPS system. The heat dissipation is calculated
(Power Dissipation x 3.42 = Heat Dissipation). It is recommended that a UPS system
be installed to protect the equipment in the event of unexpected power failure.
Make sure that the outlets and circuits will not be overloaded. Spread out the load over
at least two or three circuits or use a 3 phase circuit.
3.2 Chassis Package Contents
The package includes:
•
1 chassis with the following modules installed:
ƒ
9 spines
ƒ
1 management module
ƒ
4 fans
ƒ
6 PSUs
•
1 installation kit
•
1 box containing 6 power cords 250v 15a 2.0M, C14 to C13, USA UL Standard
•
1 cable management kit
Before you install your new IS5300 series chassis, unpack the system and check to make sure that
all the parts have been sent, check this against the parts list. Check the parts for visible damages
that may have occurred during shipping.
The leafs are shipped separately.
A second redundant management module, when ordered, is shipped separately.
Mellanox Technologies
31
Rev 1.8
Installation
If anything is damaged or missing, contact your customer representative immediately.
The rack mounting holes conform to the IEA-310 standard for 19-inch racks. Guarantee proper ventilation, by leaving 8cm (3”) of space to the front and rear of the switch.
This will ensure proper air flow through the chassis. This is crucial for maintaining
good airflow at ambient temperature. In particular, route cables such that they do not
impede the air into or out of the chassis.
3.3 Leaf Package Contents
The leafs are ordered by the customer and are shipped 4 to a box. The customer will receive as
many boxes as needed to fill the order.
3.4 Management Package Contents
The package includes:
3.5
•
one management module ordered by the customer
•
1 RJ45 to DB9 harness
Physical Installation
Warning: This equipment is very heavy. Safety is the first concern. The fully loaded
chassis weighs ~468 lbs (~212 kg). Make sure that proper manpower and equipment
is used for transporting and moving the chassis.
The switch platform uses 17U of rack space in a standard 19” rack, 16U for the chassis and 1U for
the shelf. The switch ships from the factory with mounting holes on the spine side. There are upper
brackets to connect the leaf side to the rack near the top of the chassis, and there are two lockdown bars to secure the chassis to the shelf. The weight of the switch is supported from underneath
the unit by the shelf.
32
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
This chassis can be installed in standard 19” racks that have depths between 65cm and 80cm
between the vertical supports of the rack. Make sure that a fully populated rack including cables
will have sufficient air flow for cooling.
Choose a rack which is able to support the mechanical and environmental characteristics of a fully populated switch chassis.
3.5.1 Starting with the Rack
Mellanox recommends that you remove both sides of the rack to make the installation
easier.
You will need a fork lift, to move and insert the chassis into the rack.
This chassis can be installed in 19” racks with a minimum depth of 100 cm. This depth is the minimum necessary to allow enough room for cable placement, without affecting ventilation through
the chassis.
The switch platform uses 17U of rack space in a standard 19” rack. The switch ships from the factory with mounting holes on the spine side. There are upper brackets to connect the leaf side to the
rack near the top of the chassis, and there are two lock-down bars to secure the chassis to the shelf.
The weight of the switch is supported from underneath the unit by a shelf.
The rack may need to be modified to accommodate the 5300 chassis. The distance between the
vertical supports must be between 65 and 80 cm.
Mellanox Technologies
33
Rev 1.8
Installation
65- 8
0 cm
Figure 15: Distance Between the Vertical Supports
This edge of the shelf
must be as close as
possible to the inside of
the door when closed.
3.5.2 ESD Connection
Before starting any procedure on the 5300 series Switch system:
1. Put an ESD prevention wrist strap on your wrist, and make sure there is good contact between
your body and the strap.
2. Plug the other end of the wrist strap to a valid ground. Make sure that this is a tight fit.
3.5.3 Installation Procedure
Installing the chassis will be a lot easier if you can remove the sides of the rack.
You will need a fork lift, to move and insert the chassis into the rack.
3.5.3.1
Requirements
You will need:
• #2 phillips screwdriver
• a fork lift
• measuring tape
34
Mellanox Technologies
• #3 phillips screwdriver
• a grounding lug
• ground wire of sufficient length and gauge to properly ground the
chassis
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
The installation will be much easier with a power screwdriver.
It is recommended to use AWG6 or 4mm diameter wire for grounding purposes.
It is recommended to have at least two people for the duration of the installation procedure. Use a mechanical lift to raise this chassis. If not, use enough manpower to ensure
the safety and wellbeing of all of the people involved in the installation.
•
Parts included in the installation kit:
-
-
-
1 shelf with brackets pre-installed
1 left side upper bracket offset
2 lock down bars
8 lock washers for the upper brackets to
vertical support
10 hex head bolts – 8 for the upper
brackets and 2 for the shelf extension
20 pan head screws for the caged nuts 12
for the shelf and 8 for the chassis faceplate
32 lock washers – 20 for the lock down
bars and 12 for the upper brackets to
upper bracket offsets
2 upper brackets
-
1 open end ratchet wrench 10mm
1 socket wrench
2 extensions for the socket driver
2 flat washers for the shelf extension
-
-
•
-
-
1 shelf extension
1 right side upper bracket offset
2 upper bracket washers
12 lock washers for the upper brackets to
upper bracket offsets
34 caged nuts 12 for the shelf and 8 for the
chassis faceplate
20 flat washers– 8 for the lock down bars
and 12 for the upper brackets
32 hex head bolts – 20 for the lock down
bars and 12 for the upper brackets to upper
bracket offsets
12 flat head screws with locktite for the
upper bracket offsets
1 socket nut driver 8mm
1 socket nut driver 10mm
1 socket nut driver 13mm
Parts included in the cable management installation kit:
- 1 cable management rack RH
- 10 caged nuts M6
- 1 cable management rack LH
- 10 M6 bolts
Mellanox Technologies
35
Rev 1.8
Installation
Figure 16: Installation Kit Parts
Lock-down bar
Shelf
Shelf extension
Upper bracket
Upper bracket
washer
Upper bracket offset
Flat washers
Lock washers
3.5.3.2
Caged nuts
Phillips pan head
screw
hex head bolt
Flat head screw
Opening the Container
1. Before starting the procedure, put the ESD strap on and connect it to a valid ground.
2. Remove the four sides of the container by unscrewing the phillips head screws holding the
sides on.
36
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 17: Container Screws
Container screws
3.
4.
5.
6.
Remove and put aside the box containing the cables.
Remove and put aside the box containing the cable management kit.
Remove and put aside the box containing the Installation kit.
Visually inspect the chassis, make sure that:
ƒ
there is no visible damage
ƒ
all 12 spines are installed
ƒ
6 PSUs are installed
ƒ
all 4 fans are installed
ƒ
1 management module is installed
7. Remove all protective plastic film from all sides and top of the chassis.
The leafs are shipped separately.
A second redundant management module, when ordered, is shipped separately.
Mellanox Technologies
37
Rev 1.8
Installation
Do not remove any of the blocks or either of the lock-down bars at this time.
3.5.3.3
Installing the Shelf
The chassis is on ball bearings and can roll easily. Be aware that the chassis can roll off
of the pallet. Should the chassis start to fall, move out of the way. The chassis can
cause grave bodily harm should it fall on or near you.
1. Select the location in the rack. Try to keep the chassis as low as possible to keep the center of
gravity low.
It is recommended to set the shelf at U5. Try and keep the chassis as low as possible.
The maximum height that the chassis can be mounted, will be determined by the maximum height
that the fork lift can raise the pallet.
2. Open the Installation kit and make sure that all of the parts are in the box. See
Figure 16,“Installation Kit Parts”.
The chassis will sit in the rack with the spine side as close as possible to the door.
The distance between the vertical supports must be between 65 and 80 cm. If the distance in your rack is different, move the vertical supports so that one pair is 10
cm(4in.) away from the door.
The side of the chassis with the spine units will sit flush with the vertical supports of
the rack. The side of the chassis with the QSFP connectors will sit at the edge of the
shelf closer to the center of the rack.
3. Measure the distance between the vertical supports and adjust the shelf bracket according to
this distance. This chassis can be installed a rack with a distance between the vertical supports
of from 65cm(25.6in.) to 80cm(31.5in.).
38
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
65-8
0
cm
Figure 18: Vertical Rack Supports Dimension
4. The shelf comes with the four brackets pre installed. Two of the brackets should be loose.
They may need to be removed and repositioned to meet the distance between the vertical supports of the rack.
Figure 19: Adjustable Shelf Brackets
These two brackets will
need to be adjusted. They
may even need to be
removed and repositioned.
The holes in the bracket are
offset to one side.
The holes must be closer to
the top of the shelf.
Mellanox Technologies
39
Rev 1.8
Installation
Figure 20: Top of Shelf Bracket
The holes in the bracket are
offset to one side.
The holes must be closer to
the top of the shelf.
Top of shelf
Bottom of shelf is even with this side of the
bracket, the greater distance between the holes
and the edge of the bracket show that this is the
bottom side.
Figure 21: Placing the Shelf Bracket
Adjusting slots
h tly
s l ig n c e
e
th is t a ts .
r
be
d
u ld u r e d u p p o
o
h
s
s
s
l
a
a
e
ic
ce
e m e rt
ta n
d is a n t h a c k v
s
i
T h g e r th th e r
en
la r
tw e
be
5. Insert three caged nuts into the rack for each of the four shelf brackets. Make sure that the
caged nuts are all at the same height on the vertical supports.
40
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 22: Caged Nut Locations for the Shelf Brackets
6. Put the Shelf into the rack and twist the shelf into place. Make sure the spine side of the shelf
is closest to the rack doors. See Figure 24 to identify the spine side of the shelf.
7. Install and tighten the 12 M6 bolts into the caged nuts.
Figure 23: Shelf Brackets
The spine side of
the shelf has two
slots for the
extension
Adjustable shelf
brackets
Mellanox Technologies
41
Rev 1.8
Installation
8. Tighten the 16 hex head bolts on the adjustable brackets.
9. Connect the lock-down bar onto the shelf, at the connector side. See Figure 24 to identify the
spine side of the shelf.
Figure 24: Place the Lock-Down Bar on the Shelf
Install the lock-down bar
here.
The spine side of
the shelf has two
slots for the extension
10. Place 8 caged nuts into the vertical rack support at the locations corresponding to the holes in
the chassis faceplate. The holes in the faceplate start at 2U above the shelf and are spaced
every 4U centered as you go up the vertical rack support. There are 4 holes on each side.
42
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 25: U Numbering Above Shelf
3
2
1
3
The first cage nut on the spine side goes here.
The next six caged nuts go every 4 U units up
from here.
2
7.1 cm
1
Top of
Shelf
3.5.3.4
Inserting the Chassis
1. Put the container on the fork lift.
Mellanox Technologies
43
Rev 1.8
Installation
Figure 26: Putting the Chassis in the Rack
The chassis is screwed down to the pallet on both the spine side and the leaf side.
Figure 27: Location for the Lock-down Bar
Bottom of the
chassis
44
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
2. Unscrew the lock-down bars.
3. Screw on the two Upper Bracket offsets onto the chassis using nine flat head screws for each
offset.
Figure 28: Place the Upper Bracket Offset
4. Screw on the shelf extension using two bolts with flat washers.
Figure 29: Attach the Shelf Extension
5. If you are installing the cable management system, place 10 caged nuts on the other side of the
rack in the vertical supports.
6. Place caged nuts in all of the locations specified in Figure 14. The black holes show where to
place caged nuts; the red holes show the location of the upper brackets on the leaf side.
Mellanox Technologies
45
Rev 1.8
Installation
Figure 30: Caged Nut Placement by U Numbers
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
60 cm
20
12
11
10
10
9
9
8
8
7
6
6
5
5
4
4
3
3
2
2
1
1
Spine side
7.
8.
9.
10.
46
12
11
7
These are for the cable
holder.
Leaf Side
Place the chassis in front of the rack and as close as possible to the rack.
Raise the chassis so that it is ~5cm above the shelf in the rack.
Raise the hinged extension on the container floor.
Lower the chassis until the hinged extension is sitting on the shelf extension.
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
11. Push the chassis from the container to the shelf.
Figure 31: Fork Lift
Container floor
Hinged extension
Save the container pallet until you want to remove this chassis. It will be necessary for
the removal and disposal procedures.
Figure 32: Face Plate Mounting Bolt Locations
F1
F2
IS5300
Mellanox
IS5300
S1
IS5300
IS5300
Mellanox
S2
P1
S3
Mellanox
P2
Holes in the faceplate for mounting on the rack.
The holes are separated by 4U
units
S4
S5
P3
S6
P4
S7
S8
P6
P5
S9
Mellanox Technologies
47
Rev 1.8
Installation
12. Slide the chassis onto the shelf and determine the location of the upper brackets, on the vertical
supports on the connector side of the chassis.
13. Slide the chassis out just far enough to install the upper brackets.
Figure 33: Upper Brackets and Offset Location
48
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 34: Upper Bracket Installation
This hole is 60cm up from
the top of the shelf
14. Screw the upper brackets onto the vertical supports and tighten in place. You will need the
socket wrench with both extensions to tighten these bolts.
15. Slide the chassis onto the shelf until the face plate of the chassis touches the vertical rack support.
16. Make sure the upper brackets are installed in their correct location.
17. Screw the bolts through the faceplate into the caged nuts, and tighten all 8 bolts and nuts.
18. For each offset and upper bracket, screw six bolts through the offset into the upper bracket.
Use one flat washer and one lock washer for each of these bolts.
Mellanox Technologies
49
Rev 1.8
Installation
Figure 35: Offset to Upper bracket Bolts
19. Place the front lock-down bar at the edge of the chassis and align the holes in the lock-down
bar with the holes in the shelf. Screw down the lock-down bar. You will need the 10 hex head
screws and washers for each lock down bar.
Figure 36: Lock-Down Bar
These holes are to
screw the bar into the
Chassis
These holes are to
screw the bar into the
shelf
20. Screw down the second lock-down bar.
50
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 37: Bolt and Washer Order
21. Remove the shelf extension and save for removal of the chassis.
22. Connect a valid ground, See Section 3.5.5, “Ground Connections,” on page 53, for detailed
instructions.
23. Go to Section 4, “Chassis Power Up,” on page 57 to power up the switch system.
Mellanox Technologies
51
Rev 1.8
Installation
3.5.4 Installing the Cable Holder
Now is the time to install the cable holder.
Figure 38: Cable Holder
Left side rack
Top side
1. Place the Cable holder next to the rack, on the connector side of the chassis, and identify the
holes where the caged nuts are to be placed.
The cable holders should go to the outside of the vertical supports.
2. Set the bottom of the cable holder at the level of the shelf.
52
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
3. Screw the cable holder onto the rack using the screws provided.
4. Repeat steps 1- 3 for the second cable holder.
3.5.5
Ground Connections
Make sure to connect the ground post to a valid electrical ground. Use a grounding lug and a
ground wire of sufficient capacity to safely convey a potential discharge. A ground wire of AWG 6
or 4mm diameter is recommended for grounding this device. The chassis is concurrently grounded
through each of the PSUs. Only connect the PSU cords to properly grounded outlets. Do not rely
on the PSU grounds. It is absolutely necessary to connect the grounding post. Make sure the connections are solid and permanent. If you choose to not use the ground screw, make sure that the
rack is properly grounded and that there is a valid ground connection between the chassis of the
switch and the rack. Test the ground using an Ohm meter.
Figure 39: Ground Connection
F1
F2
IS5300
Mellanox
IS5300
S1
IS5300
IS5300
Mellanox
S2
P1
S3
Mellanox
P2
S4
S5
P3
S6
P4
S7
S8
P6
P5
S9
ESD connector
Ground Post
Mellanox Technologies
53
Rev 1.8
3.6
Installation
Power Connections
The switch includes integrated hot-swap power supplies which support up to 6 load-sharing
1000W supply units. The slots for the power supply units (PSUs) are on the spine side. The left
side has odd numbered PSUs and the right side has even numbered PSUs. Each PSU has a dedicated AC inlet. This design enables the optional use of separate main and backup AC feeds. The
input voltage is Autorange, 100-240 VAC, 50Hz or 60Hz. The output voltage for the PSUs is 48V.
The power cords should be standard 3-wire AC power cords including a safety ground.
Before starting any procedure on the IS5300 series switch system put an ESD prevention wrist
strap on your wrist and connect to the IS5300 series Chassis.
3.6.1 Powering Up the Switch Platform
Note: Make sure that the power cords are compatible with your outlets. Power cords for different countries can be ordered from Mellanox.
1. Plug in the power cords to the PSUs.
2. Plug the other end of the power cord into a grounded outlets.
Make sure that the outlets and circuits will not be overloaded. Spread out the load over
at least two or three circuits or use a 3 phase circuit.
The chassis must be started with a full compliment of PSUs, thereafter it can run on one less than
the total number of PSUs. This final PSU is redundant and allows for hot swapping a PSU should
one fail. Connecting the PSUs to different AC lines provides AC failover protection.
A system should continue to run and allow a hotswap of a defective PSU. Should there not be
enough power to keep all of the leafs running, FabricIT EFM may power down some leafs. If this
happens it may be necessary to reboot the chassis once the defective PSU has been replaced.
The power system will divide the current consumption by the number of working PSUs. Should
one of the PSUs fail, the total current consumption will then be divided by the remaining working
PSUs. When the failed PSU is hot swapped the new PSU will ramp up and pass its share of current, so that the total current is always divided by the number of working PSUs.
54
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 40: Multiple Power Inlets - Electric Caution Notification
CAUTION
Risk of electric shock and
energy hazard.
The PSUs are all independent.
ACHTUNG
Gafahr des elektrischen Schocks.
Entferrnen des Netzsteckers
elnes Netzteils spannungsfrei.
Um alle Einhieten spannungsfrei
Disconnect all power supplies to zu machen sind die Netzstecker
ensure a powered down state
aller Netzteile zu entfernen
inside of the switch platform.
ATTENTION
Risque de choc et de danger
e’lectriques. Le de’branchment
d’une seule alimentation stabilise’e ne de’branch uniquement
qu’un module “Alimentation
Stabilise’e”. Pour isoler completement le module en cause, Il
faut de’brancher toutes les alimentations stabilise’es.
3. Check the Status LEDs on all of the management modules and confirm that all of the LEDs
show status lights consistent with normal operation.
Any yellow or red status LEDs on any of the management modules is cause for concern and must be dealt with immediately.
4. Check that none of the LEDs on the spines are yellow.
It can take up to 5 minutes to boot up the system. During this time the status LEDs may
be RED. Turn off the system if any LEDs remain red for more than 5 minutes.
5. Check that the Leaf status LED, Fan status LED, and Spine status LED in the spines are all
green.
Figure 41: Spine Module
Fan LED
Status
1
3 5
7 9 11 13 15 17
19 21 23 25 27 29 31 33 35
Fan Status
2 4 6
Status LED
3.7
8 10 12 14 16 18
20 22 24 26 28 30 32 34 36
Leaf connection LEDs
InfiniBand QSFP Cable Installation
The switch uses industry standard QSFP InfiniBand cables which are available from several vendors. The standard QSFP cables support full 40+40Gb/s (QDR), 20+20Gb/s (DDR) and 10+10Gb/
s (SDR) bidirectional wire speed of the switch ports. All InfiniBand QSFP connections are made
Mellanox Technologies
55
Rev 1.8
Installation
to the leaf boards. Each leaf has 18 InfiniBand QSFP connectors in two rows, which are numbered
1-18.
If maximum cable lengths are exceeded data transfer will be reduced and the bit error
rate will increase.
All cables can be inserted or removed with the unit powered on. To insert a cable, press the connector onto the port receptacle until the connector is firmly seated. The orange LED indicator
above the port will light when the physical connection is established (when both ends of the cable
are properly connected to working devices). Allow 15 seconds for link to get up. To remove, disengage the lock and slowly pull the connector away from the port receptacle. For a valid physical
connection both ends of the cable must be connected to working devices.
Take care to not impede the air flow through the ventilation holes next to the
InfiniBand ports. Use cable lengths which allow routing horizontally around to the side
of the chassis before bending upward or downward in the rack.
Cables in the bottom row should be inserted up side down in relation to the how the
cables are inserted in the top row.
Figure 42: Top and Bottom Ports
3.7.1 Cable Power Classes
Chassis and switches need to be able to dissipate the heat generated by high power I/O cables and
modules. The Mellanox IS5X00 series chassis are rated for cables up to class 2 as per the SFF
committee classification (SFF-8436.PDF).
See http://www.mellanox.com/content/pages.php?pg=cables for the cable class rating of Mellanox
cables.
56
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
4
Rev 1.8
Chassis Power Up
Before starting any procedure on the IS5300 series chassis system put an ESD prevention wrist
strap on your wrist and connect to the IS5300 series chassis.
The chassis must be started with a full complement of PSUs, that is6. Thereafter it can run on one
less than the total number of PSUs. This final PSU is redundant and allows for hot swapping a
PSU should one fail. Connecting the PSUs to different AC lines provides AC failover protection.
A system should continue to run and allow a hotswap of a defective PSU. Should there not be
enough power to keep all of the leafs running, FabricIT EFM may power down some leafs. If this
happens it may be necessary to reboot the chassis once the defective PSU has been replaced.
1. Check all:
2.
3.
4.
5.
6.
ƒ
Boards
ƒ
Power supplies
ƒ
Leaf fan modules
ƒ
Spine fan modules
for proper insertion and seating before connecting the AC power cords.
Insert all leafs that you plan to use, in the chassis.
Insert thermal blanks in unused leaf slots to maintain balanced air flow.
Tighten all mounting screws.
Connect the power cords to the PSUs.
Connect the power cords to grounded electrical outlets.
Do not power up the chassis with less than all PSUs installed.
Populate the chassis with the leafs before you power up the chassis.
4.1
Power Supply and Spine Board Indicator Status at Power ON
It can take up to 5 minutes to boot up the system. During this time the status LEDs may
be RED. Turn off the system if any LEDs remain red for more than 5 minutes.
As the power is turned on, you should observe the following conditions for normal operation:
Mellanox Technologies
57
Rev 1.8
Chassis Power Up
1. Power Supply Unit(s) AC OK and DC OK indicators are ON and FAIL indicators are OFF.
2. There is a green Status LED per spine board, per leaf board, and per management module that
indicates power supplies are good.
3. Spine Board indicators will display status of internal links to the installed leaf boards. All PHY
links to existing leaf Boards should be ON.
4. Check the Spine LEDs and make sure they coincide with Table 43.
Figure 43: Spine Side Panel Display Status Indications
STATUS
PSU
STATUS
LEAF
FANS
SPINE
FANS
MGT 1
STATUS
MGT 2
STATUS
5. Check the Spine LEDs and make sure they coincide with Table 44.
Figure 44: Management Module Status Indications for Normal Operation
I2C
CONSOLE
MGT
RST
PSU
S.FANS L.FANS MASTER
MGT MAC:
00:02:C9:11:34:8A
58
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
5
Rev 1.8
Insertion and/or Hotswap Extraction
Before starting any procedure on the IS5300 series Switch system, put an ESD prevention wrist
strap on your wrist and connect to the IS5300 series Chassis.
When hotswapping any of the units, it is necessary to wait 1 minute after removing the
defective part before inserting the new part. This is necessary so that the management
module will start a new cycle checking through the leafs and spines for the FW versions.
This switch platform supports Hotswap capabilities for the:
5.1
•
Power supply units
•
Leaf boards
•
Spine boards
•
Leaf fan module
•
Spine fan module
•
Management modules
Power Supply Units
When hotswapping any of the units, it is necessary to wait 1 minute after removing the
defective part before inserting the new part. This is necessary so that the management
module will start a new cycle checking through the leafs and spines for the FW versions.
A PSU (Power Supply Unit) can be extracted without bringing down the system, as long as no
more than one PSU is bad.
The power required to run the switch system is equally divided between all of the working PSUs.
5.1.1 Extracting and Inserting the Power Supply Unit
With all of the power supplies installed, the system is in the redundant configuration, any single
PSU may be extracted without bringing down the system.
To extract a PSU:
1. Remove the power cord from the power supply unit. Note which power cord it is according to
the AC numbering.
Mellanox Technologies
59
Rev 1.8
Insertion and/or Hotswap Extraction
Figure 45: Power Cord Top Bar
AC1
AC2
AC3
AC4
AC5
AC6
2. On the spine side of the chassis, remove the cover to the power supply unit for the non-working PSU.
Figure 46: Power Supply
Latch
Handle
DC
OK
AC
FAIL
OK
3. Grasping the handle with one hand, push the black latch release while pulling the handle outward. As the PSU unseats, the PSU status indicators will turn off.
4. Remove the PSU.
To insert a PSU:
1. Make sure the mating connector of the new unit is free of any dirt and/or obstacles.
2. Insert the PSU by sliding it into the opening until a slight resistance is felt.
3. Continue pressing the PSU until it seats completely. The latch will snap into place confirming
the proper installation.
4. Insert the power cord into the supply connector on the other side of the chassis.
5. Replace the cover over the PSUs.
The green indicators should light. If not, extract the PSU and re-insert it again.
60
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
5.2
Rev 1.8
Leaf Boards
When hotswapping any of the units, it is necessary to wait 1 minute after removing the
defective part before inserting the new part. This is necessary so that the management
module will start a new cycle checking through the leafs and spines for the FW versions.
The leaf boards are numbered from top to bottom, with corresponding numbers displayed to the
outside of the leafs vertically along the side panel.
5.2.1 Extracting a Leaf Board
Each leaf board has an ejector that locks the board in place and serves as a lever for seating or
extracting (see Figure 56).
1. Run the leaf shut down command.
no power enable <module>
switch-1 [Orca648: master] (config) # no power enable L16
2.
3.
4.
5.
Disconnect all cables connected to the leaf.
Push the latch to unlock the ejector from the chassis.
Open the ejector until it is 90 degrees from the leaf.
Pull out on the leaf.
Figure 47: Ejector Latch
Pull the leaf out of the
chassis
Leaf
Leaf
Push the latch
release
Ejector
Note: The board is short, therefore do not let go of it while sliding it out.
Mellanox Technologies
61
Rev 1.8
Insertion and/or Hotswap Extraction
Figure 48: Leaf Release
Push here to release the latch
6
7
8
9
10
Pull the ejector to remove the leaf
11
13
12
15
14
16
17
18
5.2.2 Inserting a Leaf Board
Start with the latch fully open, that is perpendicular to the front panel of the leaf. Carefully set the
leaf board into the side guide rails and slowly slide the board into the chassis. Catch the hooks onto
the vertical bar and push the latch shut.
5.3
Spine Boards
When hotswapping any of the units, it is necessary to wait 1 minute after removing the
defective part before inserting the new part. This is necessary so that the management
module will start a new cycle checking through the leafs and spines for the FW versions.
Each spine has a pair of ejectors that lock the board in place and serve as levers for seating or
extracting (see Figure 49).
5.3.1 Extracting a Spine Board
1. Run the spine shut down command.
no power enable <module>
switch-1 [Orca648: master] (config) # no power enable S06
2. Push outward on the latches to unlock the ejectors from the chassis.
3. Open the ejectors until they are 90 degrees from the module.
4. Pull out on the module using both ejectors.
62
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 49: Ejector Latch
Pull the module out of the
chassis
Management Module /Spine
Management Module /Spine
Push the latch
release
Figure 50: Spine Board Extraction
Pull the latches to remove the spine.
Status
1 3 5
7 9 11 13 15 17
19 21 23 25 27 29 31 33 35
Fan Status
2 4 6
8 10 12 14 16 18
20 22 24 26 28 30 32 34 36
5.3.2 Inserting a Spine Board
1.
2.
3.
4.
5.
Start with the latches fully open, that is perpendicular to the front panel of the leaf.
Hold the spine board by the sides with both latches fully open.
Insert the board into its rail. The board should slide in without resistance.
Push the board in until the hooks on the latches are touching the vertical bar.
Now press both latches inward simultaneously. You should feel the latches are hooked into the
front panel.
6. Press both latches applying some force to close them completely. The locking latch will
engage.
Mellanox Technologies
63
Rev 1.8
5.4
Insertion and/or Hotswap Extraction
Fan Modules
When hotswapping any of the units, it is necessary to wait 1 minute after removing the
defective part before inserting the new part. This is necessary so that the management
module will start a new cycle checking through the leafs and spines for the FW versions.
There are four fan modules on the chassis for the leafs. They are located on both sides of the chassis; two on the leaf side corners and two on the spine side. When a fan module is not functioning
the status LED on the fan will light up.
There are two different fan modules for the chassis. These fans have different model
numbers and are not interchangeable. The fans on the leaf side of the chassis are
MTF005001, whereas the fans on the spine side of the chassis are MTF005002.
Figure 51: Fan Locations on the Chassis
Fans
F1
AC1
AC2
AC3
AC4
AC5
F2
AC6
IS5300
I2C
CONSOLE MGT
I2C
RST PSU S.Fans L.Fans Master
CONSOLE MGT
RST PSU S.Fans L.Fans Master
Mellanox
IS5300
S1
IS5300
IS5300
Mellanox
S2
P1
S3
Mellanox
P2
S4
S5
P3
S6
P4
S7
S8
P6
P5
S9
5.4.1 Leaf Fan Module
There are four Leaf fan modules. Two leaf fan modules are found on the Leaf side and two leaf fan
modules are found on the Spine side.
The leaf side fans are not interchangeable with the spine side fans. Air flow through the leafs is
independent of the air flow through the spines.
5.4.1.1
Extracting the Leaf Fan Module
1. Push and hold the blue latch release. See Figure 52.
2. Slowly pull out the fan module using the handle.
64
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Figure 52: Leaf Fan Module Extraction
Latch
Handle
5.4.1.2
Inserting the Leaf Fan Module
1. Make sure the fan module is oriented correctly top side up. Confirm that the location of the
connector in the chassis will line up with the connector in the fan module.
2. Slowly slide in the new leaf fan module.
If the fan module stops before it goes in all of the way it is inserted incorrectly!
3. Push the fan module until the latch engages.
4. Make sure that the green leaf LED on the module comes on (indicating that fan is running).
5.4.2 Spine Fan Modules
Each spine fan module contains two individual fans. Should a single fan fail the Fan Status LED
on the spine and on the management module will light, indicating the necessity to replace the fan
module. Air flow through the spines is independent of the air flow through the leafs.
Each spine module has a fan module with two individual fans built in. When a fan module is not
functioning the status LED on the fan will light up.
Figure 53: Spine Fan Module
Status
1 3 5
7 9 11 13 15 17
19 21 23 25 27 29 31 33 35
Fan Status
2 4 6
8 10 12 14 16 18
20 22 24 26 28 30 32 34 36
Fan Module
Mellanox Technologies
65
Rev 1.8
Insertion and/or Hotswap Extraction
When a fan module is removed the indicator light will reset.
Figure 54: Fan Status LED on the Spine Module
1 3 5
7 9 11 13 15 17
Fan Status
2 4 6 8 10 12 14 16 18
5.4.2.1
Extracting the Spine Fan Module
1. Push the two blue latch buttons together while pulling the fan module out.
5.4.2.2
Inserting the Spine Fan Module
1. Make sure the fan module is oriented correctly top side up. Confirm that the location of the
connector in the chassis will line up with the connector in the fan module.
2. Slowly slide in the new spine fan module.
3. Push the fan module until as far as it will go, make sure the locking latches engage.
5.5
Management Module
When hotswapping any of the units, it is necessary to wait 1 minute after removing the
defective part before inserting the new part. This is necessary so that the management
module will start a new cycle checking through the leafs and spines for the FW versions.
Before starting any procedure on the IS5300 series Switch system put an ESD prevention wrist
strap on your wrist and connect to the IS5300 series Chassis.
5.5.1 Extracting a Management Module
Management modules are located on the leaf side, above the leafs. There are two places to install
the management modules.
Note: Only one management module is required to run the switch system.
Each management module has a pair of ejectors that lock the board in place and serve as a lever for
seating or extracting (see Figure 56).
1. Shut down the management module you wnat to replace using the folloing command:
no power enable <module>
switch-1 [Orca648: master] (config) # no power enable MGMT2
2. Disconnect all cables connected to the management module.
66
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
3. Push outward on the latches to unlock the ejectors from the chassis.
4. Open the ejectors until they are 90 degrees from the module.
5. Pull out on the module using both ejectors.
Figure 55: Ejector Latch
Pull the module out of the
chassis
Management Module /Spine
Management Module /Spine
Push the latch
release
Note: The board is short, therefore do not let go of it while sliding it out.
Figure 56: Management Module
I2C
CONSOLE
MGT
RST
PSU
S.FANS L.FANS MASTER
MGT MAC:
00:02:C9:11:34:8A
Ejectors
5.5.2 Inserting a Management Module
1. Start with the latch fully open, that is perpendicular to the front panel of the leaf.
2. Carefully seat the management module into the slot and slowly slide the board into the chassis
until the ejectors begin to engage on the chassis edge.
Mellanox Technologies
67
Rev 1.8
Insertion and/or Hotswap Extraction
3. Press the ejectors inward until the locks snap. This indicates that the board is fully seated.
On switch systems with dual management systems, first connect the cable and configure
the master management module CPU and only then configure the slave. By default the
master CPU is the top management module. For further information on the master and
slave roles, see the FabricIT EFM Software UM section “High Availability” for more
information.
Initial configuration must be done on all of the management modules. See the Installation Guide for the Initial Configuration procedure.
All management modules in the chassis must go through an initial configuration procedure. See the Installation Guide for the initial configuration procedure.
5.6
Switch Shut Down Procedures
5.6.1 To shut down the chassis run the following command twice:
Reload halt [noconfirm]
The switch cannot be restarted remotely!
To restart the switch you must physically go to the switch and unplug and replug
in all of the power cords to the chassis.
The first time you run the command it shuts down the master management module and the second
time shuts down the slave management module.
5.6.2 To shut down a leaf run the following command:
Reload halt [noconfirm]
5.6.3 To shut down a spine run the following command:
Reload halt [noconfirm]
68
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
6
Disassembly and Disposal
6.1
Disassembling the Chassis
1.
2.
3.
4.
5.
6.
7.
Rev 1.8
Power down the chassis.
Remove all power cables.
Remove all connector cables.
Disconnect the ground lug from the ground post.
Remove all leafs.
Remove all spines.
Remove all management modules.
Use enough people to safely lift this product.
<40 lbs
<18 kgs
40 - 70 lbs
18 - 32 kgs
70 - 121 lbs
32 - 55 kgs
>121 lbs
>55 kgs
This product and all of its parts are NOT to be disposed of with household waste. This
product contains printed circuit boards cables and batteries. According to the WEEE
Directive 2002/96/EC, all waste electrical and electronic equipment (EEE) should be
collected separately and disposed of according to the directive.
8. Dispose of these pieces in a legal and environmentally friendly way.
6.1.1 Removing the Chassis
1. Remove the screws connecting the upper brackets to the rack.
2. Remove the screws holding the chassis to the rack. These screws are located in the faceplate
on the spine side of the chassis.
3. Remove the upper brackets from the chassis.
Mellanox Technologies
69
Rev 1.8
Disassembly and Disposal
Figure 57: Mechanical Lifting Device
4.
5.
6.
7.
8.
9.
Put the container base (saved from the installation) on the fork lift.
Raise the container base to 1 cm below the level of the shelf.
Move the chassis away from the rack and onto the container base.
Put wedges around the chassis to prevent the chassis from rolling off of the container base.
Move the chassis away from the rack.
Dispose of the Chassis in a legal and environmental way.
6.1.2 Removing the Bottom Shelf
1. Remove all of the bolts that are holding the shelf to the rack.
2. Remove the shelf.
3. Remove all of the caged nuts.
70
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
6.2
Rev 1.8
Disposal
According to the WEEE Directive 2002/96/EC, all waste electrical and electronic
equipment (EEE) should be collected separately and not disposed of with regular
household waste.
Dispose of this product and all of its parts in a responsible and environmentally
friendly way.
Mellanox Technologies
71
Rev 1.8
7
Switch Management Tools
Switch Management Tools
This chapter describes the management module and tools available for Out-of-Band management
of the switch system via FabricIT EFM.
There are 2 Ethernet ports (1 for each management module) that each get connected to
Ethernet switches. These switches must be configured to 10/100M auto-negotiation.
The IS5300 switch is pre-installed with a license supporting of up to 648 nodes. If the fabric
includes more than 648 nodes, you may need to purchase Mellanox's Unified Fabric Manager™
(UFM™) software package.
OpenSM running on the switches supports up to 648 nodes. If the fabric includes more than 648
nodes, you may need to purchase Mellanox's Unified Fabric Manager™ (UFM™) software package.
The managed switch system includes the following software components:
•
Embedded OS
•
Chassis manager and system BIST
•
SNMP agent, 3rd party tool integration
•
GUI
•
Subnet Manager (SM)
•
Remote logging
•
SSH/telnet
•
Secured access in-band and out-band
•
IPv4/IPv6 network stack
The chassis manager will give the user access to:
•
Switch temperatures
•
Power supply voltages
•
Fan unit information
•
Power unit information
•
Flash memory
•
Monitoring of:
•
ƒ
AC power to the PSUs
ƒ
DC power out from the PSUs
ƒ
chassis failures
querying for:
ƒ
72
switch serial numbers
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
ƒ
revisions
ƒ
software version
ƒ
SwitchX FW version
ƒ
switch temperatures
Rev 1.8
The manager also has the ability to burn new firmware and upgrade software on the switch.
7.1
InfiniBand Subnet Manager
The InfiniBand Subnet Manager (SM) is a centralized entity running in the switch. It discovers and
configures all the InfiniBand fabric devices to enable traffic flow between those devices. The SM
applies network traffic related configurations such as QoS, routing, partitioning to the fabric
devices.
You can view and configure the Subnet Parameters (SM) via the CLI/WebUI.
Each InfiniBand subnet needs one subnet manager to discover, activate and manage the subnet. An
InfiniBand® network requires a Subnet Manager to be running in either the Infiniband switch
itself (switch based) or on one of the nodes which is connected to the Infiniband fabric (host
based).
The Subnet management features include:
In addition, the tools enable firmware management capabilities such as:
•
upgrading drivers
•
upgrading software
•
monitoring of:
•
7.2
ƒ
AC power to the PSUs
ƒ
DC power out from the PSUs
ƒ
board temperature
ƒ
fan module unit
ƒ
failure in the switch system
ƒ
system failure in the switch system
querying for board serial numbers and their revisions
Fabric Diagnostics with UFM Diag
UFM Diag is a plug & play software for fee within FabricIT EFM displaying and filtering all identified systems and nodes within the fabric.
UFM Diag includes a complete set of tools for fabric wide diagnostics to check node-node and
node-switch connectivity and to verify routes within the fabric.
Mellanox Technologies
73
Rev 1.8
Switch Management Tools
Advanced filtering allows creating filtering rules on a system wide basis, between nodes or port
connections based on traffic patterns and user assigned system names (GUIDs).
7.3
Accessing the CPU via the Ethernet Connector
Once the initial configuration is completed the management tools can be accessed through:
7.4
•
SSH
•
Telnet
•
WEB
•
SNMP
•
XML
Upgrading Software
The new software and firmware update is available to the user from the Mellanox Support website.
Copy the update to a known location on a Remote server within your LAN.
Use the CLI or the GUI in order to perform the Software upgrade. For further information please
refer to the FabricIT EFM user manual.
If FabricIT EFM is updated and the FW image in the leafs and spines of the chassis is
an earlier version than the minimum that the new version of the software can work with,
then the chassis management system may require up to ~45 minutes to update all of the
FW images in all of the leafs and spines.
74
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
8
Rev 1.8
TroubleShooting
As each PSU is plugged in, make sure that the green power LEDs on the PSU come on.
8.1
Power Supply Unit
If the Power supplies cannot supply enough power the management module may shut
down the system.
If the AC power LED is off:
1.
2.
3.
4.
5.
6.
7.
8.2
Check that the power cable is the correct power cable for your country.
Check that the power cable is plugged into a working outlet.
Check that the power cable has a voltage within the range of 100 - 240 volts AC.
Remove and reinstall the power cable.
Check the circuit breakers to be sure that the breaker has not tripped.
Check that the power cable is good. Replace the power cable.
If the AC power LED is green but the OK power LED is off or the FAIL LED is on – Replace
the PSU.
Leaf Board
The power LED for the Leaf board is off:
1. Make sure that all of the PSUs are showing DC OK.
2. Uninstall and reinstall in the Leaf board.
3. When the Yellow LED is on, this indicates a fault in the board, uninstall and reinstall the Leaf
board.
4. If uninstalling and reinstalling the Leaf board does not work, burn the latest FW on the Leaf
board and uninstall and reinstall the Leaf board.
5. Replace the Leaf board with a new one.
Should any of the boards shut down due to over temperature, wait 5 minutes and then follow the procedure starting with Step 2.
The Physical link LED for the InfiniBand connector does not come on:
1. Check that both ends of the cable are connected.
2. Check that the locks on the ends are secured.
3. Make sure that the latest FW version is installed on both the HCA card and the switch.
Mellanox Technologies
75
Rev 1.8
TroubleShooting
4. If media adapters are used check that the all connections are good, tight, and secure.
5. Replace the cable.
The Activity indication does not come on:
Check that the Subnet Manager has been started.
8.3
Management Module
8.3.1 Yellow Status LED (for the Chassis) on the Management Module is Lit
1. Reset the master management module by pushing the rest button. If you havev two management modules installed this will convert the master management module to the slave and convert the slave to the master.
2. Make sure the S.Fans and L.Fans LEDs are green.
3. Make sure that the spine and the leafs both have the same version of FW.
4. Reburn the FW and remove and reinstall the management module.
5. If you are running the chassis with only one management module, remove and reinstall the
management module. Make sure the mating connectors of the unit are free of any dirt and/or
obstacles. See Section 5.5 on page 66.
6. If you are running the chassis with only one management module, replace the management
module.
8.3.2 Yellow LED for the Leaf Fan on the Management Module is Lit
1. Make sure that there is nothing blocking the front or rear of the chassis and that the fan modules and ventilation holes are not blocked (especially dust over the holes).
2. If you find dust blocking the holes it is recommended to clean the fan unit and remove the dust
from the front and rear panels of the switch using a vacuum cleaner.
3. Determine which fan module is problematic by checking the status LED on each fan module.
4. Remove and reinstall the problematic fan unit. Make sure the mating connector of the new unit
is free of any dirt and/or obstacles. See Section 5.4 on page 64.
5. Replace the Leaf fan module.
There are two non-interchangeable types of leaf fan modules. If the new leaf fan does not
go into the chassis confirm that it is the correct fan module.
Replace defective leaf fan modules as soon as they are identified.
76
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Should any of the boards shut down due to over temperature, follow the procedure starting in Step 1.
8.3.3 Yellow LED for the Spine Fan on the Management Module is Lit
1. Determine which spine has a defective fan by checking the Fan LEDs on all of the spines.
2. Make sure that there is nothing blocking the front or rear of the chassis and that the fan modules and ventilation holes are not blocked (especially dust over the holes).
3. If you find dust blocking the holes it is recommended to clean the fan unit and remove the dust
from the front and rear panels of the switch using a vacuum cleaner.
4. Remove and reinstall the fan unit of the spine. Make sure the mating connector of the new unit
is free of any dirt and/or obstacles. See Section 5.4 on page 64.
5. Replace the spine fan module.
Replace defective spine fan modules as soon as they are identified.
8.4
Spine Board
The yellow LED on the Spine board is lit:
1. Make sure that there is nothing blocking the front or rear of the chassis and that the fan modules and ventilation holes are not blocked (especially dust over the holes).
2. If you find dust blocking the holes it is recommended to clean the fan unit and remove the dust
from the front and rear panels of the switch using a vacuum cleaner.
3. Remove and reinstall the spine board. Make sure the mating connectors of the unit is free of
any dirt and/or obstacles. See Section 5.3 on page 62.
4. Make sure that the spine and the Leafs both have the same version of FW.
5. Reburn the FW and remove and reinstall the spine.
6. Replace the spine board.
8.5
FabricIT SW
The last software update did not succeed:
1.
2.
3.
4.
Connect the RS232 connector (CONSOLE) to a laptop.
Push the reset button on the switch or management module.
You will have ~ 5 seconds to stop the U-Boot by pressing Control-B.
Choose the image to upload. Only use image 1 or image 2.
Mellanox Technologies
77
Rev 1.8
TroubleShooting
U-Boot 2009.01-mlnx1.4 (May 12 2010 - 14:08:15)
CPU:
AMCC PowerPC 460EX Rev. A at 1000 MHz (PLB=200, OPB=100,
EBC=100 MHz)
Security/Kasumi support
Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
Internal PCI arbiter disabled
32 kB I-Cache 32 kB D-Cache
Board: Mellanox PPC460EX Board
FDEF:
No
I2C:
ready
DRAM:
2 GB (ECC enabled, 400 MHz, CL3)
FLASH: 16 MB
NAND:
1024 MiB
PCI:
Bus Dev VenId DevId Class Int
PCIE0: link is not up.
PCIE1: successfully set as root-complex
01
Net:
00
15b3
bd34
0c06
00
ppc_4xx_eth0, ppc_4xx_eth1
Hit Ctrl+B to stop autoboot:
0
Mellanox FabricIT
Boot Menu:
1. EFM_PPC_M460EX EFM_1.1.1000 2010-06-24 16:32:03 ppc
2. EFM_PPC_M460EX EFM_1.1.1200
3. U-Boot prompt
Choice:
5. Select the image to boot.
78
Mellanox Technologies
2010-06-25
18 :00:03 ppc
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Appendix A: Specification Data
A.1
Specifications
Table 13 - Switch Specification Sheet IS5300
Physical
Power and Environmental
H x W x D: 28” x 19” x 27” inches
711 mm x 482.6mm x 685 mm
The shelf adds 44.5mm to the height
Weight: 212.36 kg full configuration
468 lbs. full configuration
90 kg (199 lbs) empty configuration
Input Voltage: 90-264 VAC, 50-60Hz,
[email protected]
[email protected]
Temperature: 10 to 45 Celsius
Humidity: 10% - 90% non-condensing
Mounting: 19” Rack mount (EIA-310)
Max. Air Flow Through
leafs: 16.59M3/min. (585.9 CFM)
Max. Air Flow Through
spines: 9.48 M3/min. (334.8 CFM)
SerDes Speeds: 20 and 40 Gb/s per port
Connector Types: QSFP
Center of Gravity
CoGh : 311.8 (mm from bottom of chassis)
CoGw: 222 (mm from left side surface)
CoGd : 328.14(mm from port end surface)
Measured from the bottom left corner as
one faces the switch ports.
Max Heat Output: 12,305 BTUs/hr
Power Consumption Leaf: Typical 82.28W (not including
QSFP power)
Max 89.74W (not including
QSFP power)
Power Consumption Spine: Typical 102.86W (include 2
Fans)
Max110.32W (include 2 Fans)
Power Consumption for Active
cables QSFP: 2.0W Power level #2
IS5300 324 ports
Power Consumption: Typical: 3919.80W (including
QSFP at 2W)
Typical: 3595.80W (including
QSFP at 1W)
Max: 4509.72W (including
QSFP at 2W)
Mellanox Technologies
79
Rev 1.8
Table 13 - Switch Specification Sheet IS5300
Protocol Support
InfiniBand: Auto-Negotiation of (20Gb/s, 40Gb/s)
QoS: 8 InfiniBand Virtual Lanes for all ports
Management: Baseboard, Performance, and Device
management Agents for full InfiniBand
In-Band Management
Regulatory Compliance
Safety: US/Canada: cTUVus
EU: IEC60950
International: CB
USA: FCC, Class A
Canada: ICES, Class A
EU: EN55022, Class A
EU: EN55024, Class A
EMC: EU: EN61000-3-2, Class A
EU: EN61000-3-3, Class A
Japan: VCCI, Class A
EU: IEC 60068-2-64: Random Vibration
EU: IEC 60068-2-29: Shocks,
Type I / II
ENVIRONMEN- EU: IEC 60068-2-32: Fall
TAL: Test
ACCOUSTIC: ISO 7779
ETS 300 753
SOUND POWER
LEVEL: 75.8 db(A)
Scalability and Performance
Switching Performance: Simultaneous wire-speed any port to any
port
Addressing: 48K Unicast Addresses Max. per Subnet
16K Multicast Addresses per Subnet
Replaceable Parts
Leafs Up to 18 leafs; 18-ports each
Power Supplies 6 Power Supplies standard of
of which one is redundant
Leaf Fan Modules 4 Leaf Fan Modules
Switching Capacity 26 Tb/s
Spine Fan Mod- 9 Spine Fan Modules
ules
Spines 9
Management
Modules 2 available 1 required for operation
80
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
A.2
Rev 1.8
EMC Certifications
The list of approved certifications per chassis in different regions of the world is located on the
Mellanox Website at:
www.mellanox.com/related-docs/user_manuals/Regulatory_and_Compliance_Guide.pdf
EMC Statements are also in the Regulatory and Compliance Guide.
Mellanox Technologies
81
Rev 1.8
Appendix B: Calculating the Weight of a Customized
Chassis
The weight of a customized chassis can be calculated for any possible customization as follows.
Take the weight of a chassis with:
•
all fans modules
•
all power supplies
The weight of the IS5300 chassis configured above is 154kg.
To this add:
(# of spines * 3.73) (# of leafs * 2.67) + ((# of leaf blanks) * 0.764) + 3.15 (if you will have two
management modules) + 1.15 (if you will have only one management module) = weight of the
chassis plus the leaf boards, spines, PSUs, and Management modules installed in the chassis.
82
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Appendix C: Calculating the Power of a Customized Chassis
To calculate the power consumption of a customized chassis take the base power and add the
power of the fans, spines, management modules, and leafs.
Table 14 - Power Consumption of Chassis Parts
Part
typ power passive cables
typ power active cables @ 2W per
port
IB QDR leaf
82.28W
121.45
Spine
103W
Not applicable
Fan
45
Not applicable
Management Module
20
Not applicable
To calculate the chassis power:
((103W * # of spines) + (20W * # of management modules) + (45W * # of fans) + (82.28W * # of
leafs for passive cables) or (121.45W * # of leafs for active cables)) / 0.85 Where 0.85 is the power
supply efficiency.
Mellanox Technologies
83
Rev 1.8
Appendix D: QSFP Interface
20
21
22
23
24
25
26
27
28
29
30
31
19
GND
GND
Rx2n
Rx1n
18
Rx2p
Rx1p
17
GND
16
GND
Rx4n
Rx3n
Rx4p
Rx3p
GND
GND
ModPrsL
SDA
IntL
SCL
VccTx
Vcc1
LPMode
Vcc Rx
ResetL
ModSelL
15
1
GND
Ground
2
Tx2n
Transmitter Inverted Data Input
12
3
Tx2p
Transmitter Non-Inverted Data Input
11
4
GND
Ground
10
5
Tx4n
Transmitter Inverted Data Input
9
6
Tx4p
Transmitter Non-Inverted Data Input
8
7
GND
Ground
7
8
GND
GND
Tx3p
Tx4p
34
Tx3n
35
GND
Tx4n
GND
36
Tx1p
Tx2p
3
Tx1n
GND
Tx2n
2
1
GND
Mellanox Technologies
ModSelL Module Select
6
9
ResetL
Module Reset
5
4
10
Vcc Rx
+3.3 V Power supply receiver
11
SCL
2-wire serial interface clock
12
SDA
2-wire serial interface data
13
GND
Ground
14
Rx3p
Receiver Non-Inverted Data Output
15
Rx3n
Receiver Inverted Data Output
16
GND
Ground
17
Rx1p
Receiver Non-Inverted Data Output
18
Rx1n
Receiver Inverted Data Output
19
GND
Ground
20
GND
Ground
21
Rx2n
Receiver Inverted Data Output 3
22
Rx2p
Receiver Non-Inverted Data Output 3
23
GND
Ground
24
Rx4n
Receiver Inverted Data Output 3
25
Rx4p
Receiver Non-Inverted Data Output 3
26
GND
Ground
27
84
Signal Description
13
33
38
Connector Connecto
Pin
r Pin
Number
Name
14
32
37
Table 15 - InfiniBand QSFP Connector Pinout
ModPrsL Module Present
28
IntL
Interrupt
29
Vcc Tx
30
Vcc 1
31
LPMode
32
GND
Ground
33
Tx3p
Transmitter Non-Inverted Data Input
34
Tx3n
Transmitter Inverted Data Input
35
GND
Ground
36
Tx1p
Transmitter Non-Inverted Data Input
37
Tx1n
Transmitter Inverted Data Input
38
GND
Ground
+3.3 V Power supply transmitter
+3.3 V Power Supply
Low Power Mode
SDA
GND
RX3p
RX3n
GND
SCL
RX1n
ResetL
RX1p
15
GND
14
VccRx
13
19
12
ModSelL
20 GND
21 RX2n
22 RX2p
23 GND
24 RX4n
25 RX4p
26 GND
27 ModPrsL
28 IntL
29 VccTx
30 Vcc1
31 LPMode
32 GND
14
13
12
11
1
0
9
8
7
6
5
4
3
2
1
GND
11
1
0
9
18
8
17
7
GND
15
TX2n
33 TX3p
TX2p
6
16
5
TX4p
16
GND
34 TX3n
TX4n
4
TX4n
TX4p
19
18
17
GND
35 GND
ModSelL
3
GND
ResetL
36 TX1p
SCL
2
TX2p
SDA
1
TX2n
GND
37 TX1n
GND 3 8
TX1n 3 7
TX1p 3 6
GND 3 5
TX3n 3 4
TX3p 3 3
GND 3 2
RX3p
Top 18.35
LPMode 3 1
Vcc1 30
RX3n
VccRx
GND
RX1p
RX1n
38 GND
Top
VccTx 29
IntL 28
ModPrsL 27
GND 26
RX4p 25
RX4n 24
GND 23
RX2p 22
RX2n 21
GND 20
GND
GND
18.35
View into Rear of
Connector
Rev 1.8
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Figure 58: QSFP Connector Male and Female Views
8.50
View into Front of Cage
8.50
85
Mellanox Technologies
Rev 1.8
Appendix E: Replacement Parts Ordering Numbers
Table 16 - Replacement Parts Ordering Numbers
Part Description
OPN
324 port QDR capable modular chassis, includes fans MIS5300Q-6DNC
and power supplies, RoHS5
Power supply unit PSU
MTP005001
Power supply blank
MTM005001
Leaf board unit 18 port QDR
MIS5001QC
Modular Switch Family, Leaf - Blank
MTM005004
Spine board unit for QDR Switch system
MIS5002QC
Spine board blank
MTM005002
PPC460 Management Module
MIS5600MDC
Management module blank
MTM005003
Fan unit for Chassis Leaf side
MTF005001
Fan unit for Chassis Spine side
MTF005002
Modular Switch Family, Management - Blank
MTM005003
Rack Installation Kit for IS5600/SX6536 Series
MTR005600
Cable Management Device Set for IS5600/SX6536
MTR005601
Cables Set For IS5600/SX6536 Series
MTR005602
IS5600/SX6536, IS5300/SX6518 Series Modular
Switch, leaf cooling chassis fan unit located on Leaf
Side
MTF005001
IS5600/SX6536, IS5300/SX6518 Modular Switch,
leaf cooling chassis fan unit located on Spine Side
MTF005002
IS5600/SX6536, IS5300/SX6518 Modular Switch
MTF005005
Series Spine Fan Unit
Fan unit for spines
MTF005003
DB9 to RJ45 Harness
HAR000028
Power cord 250V 15A 2.0M C14 to C13
ACC000334
Power cord 125V 15A 2.0M C14 TO C13
ACC000242
Power cord Type B for USA, Canada, Mexico, Taiwan ACC000204
Power cord Type H for Israel
86
Mellanox Technologies
ACC000205
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Part Description
Rev 1.8
OPN
Power cord Type E/F for Sweden, France, Germany,
Netherlands, Russia
ACC000207
Power cord Type G for UK
ACC000208
Power cord Type D for India
ACC000209
Power cord Type I for China
ACC000210
Power cord Type J for Switzerland
ACC000211
Power cord Type B for Japan
ACC000212
Power cord Type I for Australia
ACC000213
Mellanox Technologies
87
Rev 1.8
Appendix F: Avertissements de sécurité d’installation
(French)
1. Instructions d’installation
Lisez toutes les instructions d’installation avant de brancher le matériel à la source
d’alimentation électrique.
2. Température excessive
Ce matériel ne doit pas fonctionner dans une zone avec une température ambiante
dépassant le maximum recommandé de 45°C (113°F). Un flux d’air de 200LFM à
cette température ambiante maximale est nécessaire. En outre, pour garantir un bon
écoulement de l’air, laissez au moins 8 cm (3 pouces) d’espace libre autour des ouvertures de ventilation.
3. Empilage du châssis
Le châssis ne doit pas être empilé sur un autre matériel. Si le châssis tombe, il peut provoquer des blessures corporelles et des dégradations de biens.
4. Connection d'Alimentation electrique excedentaire -dangers électriques
Ce produit comporte un couvercle transparent sur l’espace pour l’alimentation électrique redondante.
Ne pas faire fonctionner le produit si le couvercle transparent n’est pas solidement
fixé ou s’il est enlevé.
5. Orages – dangers électriques
Pendant un orage, il ne faut pas utiliser le matériel et il ne faut pas brancher ou
débrancher les câbles.
6. Branchement/débranchement des câbles InfiniBand en cuivre
Les câbles InfiniBand en cuivre sont lourds et ne sont pas flexibles, il faut donc faire
très attention en les branchant et en les débranchant des connecteurs. Consultez le fabricant des câbles pour connaître les mises en garde et les instructions spéciales.
7. Montage et entretien sur baie
Lorsque ce produit est monté ou entretenu sur baie, il faut prendre des précautions spéciales pour s’assurer que le système reste stable. En général, il faut remplir la baie avec
du matériel de bas en haut.
88
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
8. Fuite>3.5mA Leakage >3.5mA
« ATTENTION – La connexion à la terre des forts courants de fuite est essentielle
avant le branchement de l’alimentation. »
Avant de brancher l’appareil à la conduite d’alimentation, les vis de protection à la
terre du terminal de l’appareil doivent être appliquées à l’installation de protection à la
Terre du bâtiment.
9. Forts Courants de Fuite High Leakage Current
Attention: Forts courants de fuite. Il est essentiel de relier a la terre avant de brancher
l'alimentation.
10. Ajouter une information de connexion à la masse Connect a Valid Ground to this Device
Avant de brancher l’appareil à la conduite d’alimentation, les vis de protection à la
terre du terminal de l’appareil doivent être appliquées à l’installation de protection à la
Terre du bâtiment.
11. Installation du matériel
Ce matériel ne doit être installé, remplacé ou entretenu que par du personnel formé et
qualifié.
12. Elimination du matériel
L’élimination de ce matériel doit s’effectuer dans le respect de toutes les législations et
réglementations nationales en vigueur.
13. Codes électriques locaux et nationaux
Ce matériel doit être installé dans le respect des codes électriques locaux et nationaux.
14. Codes d’installation
L’appareil doit être installé selon l’ancienne version des codes électriques nationaux du
pays. Pour l’Amérique du Nord, l’équipement doit être installé conformément aux
spécifications du Code Electrique National Américain et du Code Electrique Canadien.
Mellanox Technologies
89
Rev 1.8
15. Interconnexion des unites
Les câbles de branchement à l’unité RS232 et les interfaces Ethernet doivent être certifiés UL de type DP-1 ou DP-2. (Note - lorsqu’il existe dans un circuit non LPS)
Protection contre la surintensité : Un appareil de protection répertorié facilement
accessible contre la surintensité du circuit de branchement et calibré à 20A doit être
incorporé dans le câblage électrique du bâtiment.
16. Exposition au rayonnement grave
Mise en garde – l'utilisation de commandes ou de réglages ou l'exécution de procédures autres que ce qui est spécifié dans les présentes peut engendrer une exposition au
rayonnement grave.
PRODUIT LASER DE CLASSE 1 » et références aux normes laser les plus récentes
CEI 60 825-1:1993 + A1:1997 + A2:2001 et NE 60825-1:1994+A1:1996+ A2:2001
17. S’assurer que les enceintes sont appropriées
Des enceintes électriques, mécaniques et incendie adaptées doivent être fournies par le
fabricant du produit final ou par l’utilisateur final.
18. Cordons électriques CA homologués UL
Pour les prises électriques en Amérique du Nord, choisissez un cordon électrique
homologué UL et certifié CSA
à 3 conducteurs, [18 AWG], terminé par une fiche moulée, d’une tension nominale de
125 V, [15 A], avec une longueur minimale de 1,5 m [6 pieds] et d’une longueur maximale de 4,5 m [18 pieds]
Pour les prises électriques en Europe, choisissez un cordon électrique harmonisé internationalement et marqué "<HAR>",
à 3 conducteurs, d’un diamètre de fil minimum de 0,75 mm2, d’une tension nominale
de 300 V, avec une gaine isolée en PVC. Le cordon doit avoir une fiche moulée d’une
tension nominale de 250 V et d’une intensité nominale de 10 A.
90
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
Anhang G: Installation - Sicherheitshinweise (German)
1. Installationsanleitungen
Lesen Sie alle Installationsanleitungen, bevor Sie das Gerät an die Stromversorgung
anschließen.
2. Übertemperatur
Dieses Gerät sollte nicht in einem Bereich mit einer Umgebungstemperatur über der
maximal empfohlenen Temperatur von 45°C (113°F) betrieben werden. Es ist ein Luftstrom von 200 LFM bei maximaler Umgebungstemperatur erforderlich. Außerdem
sollten mindestens 8 cm (3 in.) Freiraum um die Belüftungsöffnungen sein, um einen
einwandfreien Luftstrom zu gewährleisten.
3. Stapeln des Chassis
Das Chassis sollte nicht auf andere Geräte gestapelt werden. Wenn das Chassis herunterfällt, kann es zu Verletzungen und Beschädigungen an Geräten führen.
4. Redundanter Stromversorgungsanschluss - Elektrische Gefahr
Dieses Produkt verfügt über eine Abdeckung über dem Bereich für die redundante
Stromversorgung. Betreiben Sie das Produkt nicht, wenn diese Abdeckung nicht sicher
festsitzt oder entfernt wurde.
5. Bei Gewitter - Elektrische Gefahr
Arbeiten Sie während eines Gewitters und Blitzschlag nicht am Gerät, schließen Sie
keine Kabel an oder ab.
6. Anschließen/Trennen von InfiniBand-Kupferkabel
InfiniBand-Kupferkabel sind schwer und nicht flexible. Deshalb müssen sie vorsichtig
an die Anschlüsse angebracht bzw. davon getrennt werden. Lesen Sie die speziellen
Warnungen und Anleitungen des Kabelherstellers.
7.
Rack-Montage und Wartung
Wenn dieses Produkt in einem Rack montiert oder gewartet wird, sind besondere Vorsichtsmaßnahmen zu ergreifen, um die Stabilität des Systems zu gewährleisten. Im
Allgemeinen sollten Sie das Gestell von unten nach oben mit Geräten füllen.
Mellanox Technologies
91
Rev 1.8
8. Geräteinstallation
Diese Gerät sollte nur von geschultem und qualifiziertem Personal installiert, ausgetauscht oder gewartet werden.
9. Geräteentsorgung
Die Entsorgung dieses Geräts sollte unter Beachtung aller nationalen Gesetze Bestimmungen erfolgen.
10. Regionale und nationale elektrische Bestimmungen
Dieses Gerät sollte unter Beachtung der regionalen und nationalen elektrischen
Bestimmungen installiert werden.
11. Richtigen Schutz sicherstellen
Geeigneter elekrischer, mechanischer und Feuerschutz sind vom
Hersteller des Endprodukts oder dem Endbenutzer bereitzustellen.
12. Strahlenkontakt
Achtung – Nutzung von Steuerungen oder Einstellungen oder Ausführung von Prozeduren, die hier nicht spezifiziert sind, kann zu gefährlichem Strahlenkontakt führen..
Klasse 1 Laserprodukt und Referenzen zu den aktuellsten Lasterstandards :
ICE 60 825-1:1993 + A1:1997 + A2:2001 und EN 60825-1:1994+A1:1996+ A2:2001
13. UL-und CSA Certified Netzkabel UL Listed and CSA Certified Power Supply Cord
Für Nordamerika Stromanschluss, wählen Sie ein Netzkabel, das UL-und CSA Certified
3 - Leiter, [18 AWG], mit einem angespritztem Stecker bewertet bei 125 V, [15], mit
einer Mindestlänge von 1,5 m [Six Feet] aber nicht mehr als 4,5 m.
Für die europäischen Zusammenhang, wählen Sie ein Netzkabel, das international
harmonisiert und der Aufschrift "<HAR>",
3 - Leiter, mindestens 0,75 mm2 Draht, bewertet mit 300 V, mit einem PVC-Mantel
isoliert. Das Kabel muss eine angespritztem Stecker bewertet bei 250 V, 10 A. "
92
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
14. Ableitstrom> 3.5mA LEAKAGE >3.5mA
WARNUNG: Hohe Ableitstrom; Earth Verbindung, bevor Sie die Verbindung von
wesentlicher Bedeutung werden.
15. Add GND Verbindung Informationen Add GND connection information
Bevor Sie dieses Gerät an das Stromnetz, die Schutzerde Terminal Schrauben dieses
Gerät muss an den Schutzleiter in der Gebäudeinstallation.
16. INSTALLATION CODES INSTALLATION CODES
Dieses Gerät muss installiert sein, entsprechend auf die neueste Version des Landes
National Electrical Code. Für Nordamerika, müssen in Übereinstimmung mit den geltenden Vorschriften in der US-amerikanischen National Electrical Code und dem
Canadian Electrical Code.
17. Zusammenschaltung von EINHEITEN INTERCONNECTION OF UNITS
Kabel für den Anschluss an das Gerät RS232-und Ethernet-Schnittstellen müssen UL
zertifiziert Typ DP-1 oder DP-2. (Hinweis-, wenn nicht mit Wohnsitz in LPS-Schaltung)
Überstromschutz: Eine leicht zugängliche Auflistung Abzweigleitung ÜberstromSchutzeinrichtung 20 A bewertet werden müssen in dem Gebäude Verkabelung.
Mellanox Technologies
93
Rev 1.8
Appendix H: Advertencias de seguridad para la instalación (Spanish)
1. Instrucciones de instalación
Antes de conectar el equipo a la fuente de alimentación, leer todas las instrucciones de instalación.
2. Lesión corporal por peso
Dado que el equipo es muy pesado, se debe mover únicamente mediante un
elevador mecánico, para evitar lesiones.
3. Instalación en un lugar con acceso restringido.
Esta unidad ha sido ideada para instalar en lugares de acceso restringido.
4. Sobrecalentamiento
No se debe utilizar el equipo en un área con una temperatura ambiente superior
a la máxima recomendada: 45°C (113°F). Además, para garantizar una circulación de aire adecuada, se debe dejar como mínimo un espacio de 8 cm (3 pulgadas) alrededor de las aberturas de ventilación.
5. Apilamiento del chasis
Los chasis no se deben apilar sobre otros equipos. La caída del chasis podría
causar lesiones corporales, así como daños al equipo.
6. Conexión de fuente de alimentación redundante: peligro de descarga eléctrica
Este producto incluye una fuente de alimentación redundante o, en su lugar, una
vacía. Si se dispone de una fuente de alimentación vacía, no utilizar el producto
si su tapa está quitada o no está bien cerrada.
7. Cuando hay rayos: peligro de descarga eléctrica
No utilizar el equipo ni conectar o desconectar cables durante períodos de actividad de rayos.
94
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
8. Conexión y desconexión del cable Copper InfiniBand
Dado que los cables de cobre InfiniBand son pesados y no son flexibles, su conexión a los conectores y su desconexión se deben efectuar con mucho cuidado.
Para ver advertencias o instrucciones especiales, consultar al fabricante del
cable.
9. Montaje y mantenimiento de bastidores
Al instalar o realizar el mantenimiento de este aparato en un bastidor, es preciso
adoptar precauciones especiales para garantizar que el sistema se mantenga
estable. En general, en un bastidor, los equipos se deben instalar comenzando
desde abajo hacia arriba.
10. Instalación de equipos
La instalación, el reemplazo y el mantenimiento de este equipo estarán a cargo
únicamente de personal capacitado y competente.
11. Asegurar confinamientos adecuados
El fabricante del producto final o el usuario final deberán suministrar
un confinamiento adecuado para componentes eléctricos y mecánicos y contra incendio.
12. Eliminación de equipos
La eliminación definitiva de este equipo se debe efectuar conforme a todas las leyes y
reglamentaciones nacionales.
13. Códigos eléctricos locales y nacionales
Este equipo se debe instalar conforme a los códigos eléctricos locales y nacionales.
Mellanox Technologies
95
Rev 1.8
14. Cable de alimentación homologado por UL y con certificación CSA
En conexiones de América del Norte, seleccionar un cable de alimentación
homologado por UL y con certificación CSA de tres conductores, [16 AWG], terminado en un enchufe moldeado con capuchón de 125 voltios nominal, [13 A], con una
longitud mínima de 1,5 metros, pero no más de 4,5 metros.
En conexiones europeas, seleccionar un cable de alimentación armonizado
internacionalmente y marcado "<HAR>", de tres conductores, hilo de 1,0 mm2 como
mínimo, 300 voltios nominal, con cobertura protectora aislante de PVC. El cable debe
tener un enchufe moldeado con capuchón de 250 voltios nominal, 10 A.
15. Fuga > 3,5 mA
ADVERTENCIA: Alta corriente de fuga. Es esencial efectuar la conexión a tierra
antes de conectar la alimentación.
16. Añadir conexión a tierra
Antes de conectar el dispositivo a la línea de alimentación, los tornillos del terminal de
la puesta a tierra de protección del dispositivo se deben conectar a la puesta a tierra de
protección de la instalación del edificio.
(Información de conexión a tierra):
La instalación del edificio deberá prover un medio para la conexión con la puesta a
tierra de protección y un técnico de servicio deberá conectar permanentemente el
equipo a dicho medio de conexión.
Un TÉCNICO DE SERVICIO comprobará si la toma eléctrica de la que se suministrará corriente al equipo provee una conexión con la puesta a tierra de protección del
edificio. De no ser así, el TÉCNICO DE SERVICIO se encargará de instalar un CONDUCTOR DE CONEXIÓN A TIERRA DE PROTECCIÓN, del terminal de puesta a
tierra de protección separado al conductor de tierra de protección del edificio. El
equipo se instalará en un área donde haya conexión equipotencial, como por ejemplo,
un centro de telecomunicaciones o una sala de computadoras dedicada.
17. Códigos de instalación
Este dispositivo se debe instalar conforme a la versión más reciente de los códigos
eléctricos nacionales del país en cuestión. En América del Norte, el equipo se debe
instalar de acuerdo con las disposiciones vigentes del Código Eléctrico Nacional de los
EE.UU. y del Código Eléctrico de Canadá.
18. Interconexión de unidades
Los cables para la conexión con las interfaces RS232 y Ethernet de la unidad deben
estar homologados por UL tipo DP-1 o DP-2. (Nota: cuando residen en circuito no de
tipo LPS)
Protección contra sobrecargas: Al cableado del edificio se debe incorporar un dispositivo de protección contra sobrecargas de circuito derivado, de fácil acceso, con una corriente nominal de 20 A.
96
Mellanox Technologies
324 Port InfiniBand QDR Switch Platform Hardware User Manual
Rev 1.8
19. Exposición a niveles de radiación peligrosos
Precaución: el uso de controles o ajustes o la realización de procedimientos distintos de
los que aquí se especifican podrían causar exposición a niveles de radiación peligrosos.
PRODUCTO LÁSER DE CLASE 1 y referencia a las normas de láser más recientes:
IEC 60825-1:2007/03 y EN 60825-1:2007
20. Directiva sobre RAEE
Conforme a la Directiva 2002/96/CE sobre RAEE, todos los residuos de equipos eléctricos y electrónicos (EEE) se deben recolectar por separado y no se deben eliminar
junto con residuos domésticos.
Al deshacerse de este producto y de todas sus partes, hágalo de una manera responsable
y respetuosa con el medio ambiente.
Mellanox Technologies
97
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement