Data Logger ZR-RX Series CSM_ZR-RX_DS_E_2_1 Powerful backup capabilities for every conceivable on-site measurement • Provides peace of mind through support for all channels isolated input and multi-function input. • Expandable up to 200 channels (ZR-RX45). • Easy-to-use LAN connection (ZR-RX45 and ZR-RX70). For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Be sure to read “Safety Precautions” on page 5. Ordering Information Standard set Item Data Logger Option Applicable Standards CEE CCC PSE CEE Data Logger CCC PSE CEE Data Logger CCC PSE Model ZR-RX70A-E ZR-RX70A-CHRO ZR-RX70A ZR-RX45A-E ZR-RX45A-CHRO ZR-RX45A ZR-RX25A-E ZR-RX25A-CHRO ZR-RX25A Item Battery Pack Humidity Sensor (3 m) DC Cable (2 m) Logic Alarm Cable (2 m) Base Set (For ZR-RX45) Extension Terminal Set (For ZR-RX45) BNC-Crocodile Cable (2 m) (For ZR-RX70) Special PC Software Wave Inspire RX Model ZR-XRB1 ZR-XRH1 ZR-XRD1 ZR-XRL1 ZR-XRE1 ZR-XRT1 ZR-XRC1 ZR-SX10 1 ZR-RX Ratings and Specifications Main Unit Item Input method Input terminal shape Number of analog input channels Sampling speeds A/D resolution A/D conversion system Voltage Measurement ranges ThermoTem- couple pera- Resistance ture temperature detector Humidity Digital input External input/output Alarm output sections Trigger functions Functions Filter functions Calculation function Type [email protected] [email protected] [email protected] All channels isolated input, Simultaneous sampling of all All channels isolated input *1 All channels isolated input channels BNC terminal: For voltage measurement M3 screw type terminal M3 screw type terminal: For voltage/ temperature measurement *2 Standard: 20 ch Max.: 200 ch 10 ch 8 ch (When the terminal unit is connected) 10 μs to 1 min 10 ms (when 1 ch is used) to 1 h 16 bit Sequential comparison Delta-sigma 20, 50, 100, 200, 500 mV, 1, 2, 5, 10, 20, 50, 100, 200, 500 V, 20, 50, 100, 200, 500 mV, 1, 2, 5, 10, 20, 50 V, 1-5 V F.S. 1-5 V F.S. K, J, E, T, R, S, B, N, W (WRe5-26) − Pt100, JPt100, Pt1000 (IEC751) − 0% to 100% (Voltage 0 to 1 V scaling conversion) *3 Logic input (4 ch) or Pulse input (4 ch) *4 *5 4 ch (Open collector output) External trigger input (1 ch), input signal level, time In combination with timer mode, External trigger input (1 ch), Input External trigger input (1 ch), date and time can be set, and a wide signal level, time, duration, alarm Input signal level, time, duration variety of trigger settings such as “Every Day Cycle” and “Every Hour Cycle” can be made Off, Line, 5 Hz, 50 Hz, 500 Hz Off, 2, 5, 10, 20, 40 (moving average) Statistical calculation *6 : Average, peak, maximum, minimum, RMS (maximum of 2 can be set simultaneously) LAN (100BASE-TX), USB 2.0 (HIGH SPEED) USB1.1 (FULL SPEED) Web server function, FTP server Web server function, FTP server function, FTP client function, NTP Ethernet function, NTP client function PCI/F − Func- functions Realtime data transfer to the PC, Unit client function, Realtime data transfer to the PC, Unit control from tion control from a PC a PC USB Realtime data transfer to the PC RAM: approx. 64 MB Internal Flash memory: approx. 4 GB *7 Memory Flash memory: approx. 256 MB devices External USB memory *7 5.7-inch color LCD 5.7-inch color LCD 4.3-inch color LCD Display (QVGA: 320 × 240 dots) (VGA: 640 × 480 dots) (WQVGA: 480 × 272 dots) 0 to 40°C, 5 % to 85 % (15 to 35°C 0 to 45°C, 5% to 85% (0 to 40°C when operated on batteries, 15 to 35°C Operating environment when operated on batteries) when charging batteries) Vibration resistance Equivalent to automobile parts Type 1 Category A classification AC adapter: 100 to 240 VAC/50 to AC adapter; 100 to 240 VAC/50 to 60 Hz *8, 60 Hz *8, Power supply DC drive: 8.5 V to 24 V, DC drive: 8.5 V to 24 V, Battery: 7.4 VDC (2 packs) Battery: 7.4 VDC 42 VA 32 VA 29 VA Power consumption (When the AC adapter is used) (When the AC adapter is used) (When the AC adapter is used) Approx. 900 g Approx. 1.1 kg Approx. 520 g Weight (Including one terminal unit, (Excluding batteries and AC adapter) (Excluding battery and AC adapter) excluding batteries and AC adapter) External dimensions 232 × 150 × 80 mm 232 × 152 × 50 mm 194 × 117 × 42 mm Accessories User’s Manual, Utility disk (CD-ROM), AC Adapter/AC cable *1. *2. *3. *4. *5. *6. *7. *8. Resistance temperature detector is non-isolated. BNC terminal and M3 screw type terminal of the same channel cannnot be used simultaneously. A humidity sensor ZR-XRH1 is necessary. A logic alarm cable ZR-XRL1 is necessary. Pulse input: Revolutions mode/Counts mode/Inst. mode switch method Designate real-time or between-cursors mode (during playback) 1 file max. 2GB (The capacity will vary depending on the external memory used.) Be sure to use only the AC cable and AC adapter provided as accessories. 2 ZR-RX Measurement Accuracy Item [email protected] [email protected]/[email protected] ±0.25% of F.S. Voltage Temperature Thermocouple *1 R/S B K E T J ±0.1% of F.S. Measurement temperature range (°C) Measurement accuracy Measurement temperature range (°C) Measurement accuracy 0 ≤ TS ≤ 100 ±7.0°C 0 ≤ TS ≤ 100 100 < TS ≤ 300 ±5.0°C 100 < TS ≤ 300 ±3.0°C R : 300 < TS ≤ 1,600 ±(0.05% of rdg + 3.0°C) R : 300 < TS ≤ 1,600 ±(0.05% of rdg + 2.0°C) S : 300 < TS ≤ 1,760 ±(0.05% of rdg + 3.0°C) S : 300 < TS ≤ 1,760 ±(0.05% of rdg + 2.0°C) 400 ≤ TS ≤ 600 ±5.5°C 400 ≤ TS ≤ 600 ±3.5°C 600 < TS ≤ 1,820 ±(0.05% of rdg + 3.0°C) 600 < TS ≤ 1,820 ±(0.05% of rdg + 2.0°C) ±5.2°C −200 ≤ TS ≤ −100 ±(0.05% of rdg + 3.0°C) −200 ≤ TS ≤ −100 ±(0.05% of rdg + 2.0°C) −100 < TS ≤ 1,370 ±(0.05% of rdg + 2.0°C) −100 < TS ≤ 1,370 ±(0.05% of rdg + 1.0°C) −200 ≤ TS ≤ −100 ±(0.05% of rdg + 3.0°C) −200 ≤ TS ≤ −100 ±(0.05% of rdg + 2.0°C) −100 < TS ≤ 800 ±(0.05% of rdg + 2.0°C) −100 < TS ≤ 800 ±(0.05% of rdg + 1.0°C) −200 ≤ TS ≤ −100 ±(0.1% of rdg + 2.5°C) −200 ≤ TS ≤ −100 ±(0.1% of rdg + 1.5°C) −100 < TS ≤ 400 ±(0.1% of rdg + 1.5°C) −100 < TS ≤ 400 ±(0.1% of rdg + 0.5°C) −200 ≤ TS ≤ −100 ±3.7°C −200 ≤ TS ≤ −100 ±2.7°C −100 < TS ≤ 100 ±2.7°C −100 < TS ≤ 100 ±1.7°C 100 < TS ≤ 1,100 ±(0.05% of rdg + 2.0°C) 100 < TS ≤ 1,100 ±(0.05% of rdg + 1.0°C) N 0 ≤ TS ≤ 1,300 ±(0.1% of rdg + 2.0°C) 0 ≤ TS ≤ 1,300 ±(0.1% of rdg + 1.0°C) W 0 ≤ TS ≤ 2,000 ±(0.1% of rdg + 2.5°C) 0 ≤ TS ≤ 2,000 ±(0.1% of rdg + 1.5°C) *1. • ZR-RX70 Operating environment 23°C ±5°C When 30 minutes or more have elapsed after power was switched on Filter Line/GND connected; Thermocouple used is T: 0.32 dia., others: 0.65 dia. *1. • ZR-RX25/RX45 Operating environment 23°C ±5°C When 30 minutes or more have elapsed after power was switched on Sampling 1 s/Filter ON (10 times) GND connected Thermocouple used is T: 0.32 dia., others: 0.65 dia. Resistance temperature detector is available only for ZR-RX45. Measurement Accuracy (ZR-RX45 only) Humidity Sensor ZR-XRH1 (Option) Resistance temperature detector Measurement temperature range (°C) Applied current Measurement accuracy Item Description Allowable temperature −25 to + 80°C range Pt100 −200 to 850°C (FS=1,050°C) 1 mA ±1.0°C Allowable humidity range 0% to 100% JPt100 −200 to 500°C (FS=700°C) 1 mA ±0.8°C Relative humidity measurement accuracy ±3% (5% to 98% at 25°C) Pt1000 −200 to 500°C (FS=700°C) 0.2 mA ±0.8°C Response time 15 sec (90% response when membrane filter installed) Sensor output 0 to 1 VDC External dimensions dia. 14 mm × 80 mm (excluding cable) Cable length 3m 3 ZR-RX PC Software Item Special PC software ZR-SX10 Standard PC software Wave Inspire RX (Since Ver.2.4) (Option Specifications) Smart Viewer RXW (Since Ver.2.0) Smart Viewer RX70 (Since Ver.2.0) (Standard accessories) (Standard accessories) Compatible logger ZR-RX25/RX45/RX70/RX20/RX40 Compatible operating system ZR-RX25/RX45/RX20/RX40 ZR-RX70 Windows XP / Windows Vista / Windows 7 CPU Intel-compatible, 1 GHz or faster processor recommended, Intel Atom CPU not supported Pentium 4: 2.0 GHz or faster processor recommended, Intel Atom CPU not supported Memory Windows XP: 512 MB or more Windows Vista / Windows 7: 1GB or more 512 MB or more (recommended: 1 GB or more) Display 1024 × 768 or higher, screen resolution, 65,535 1024 × 768 or higher screen resolution color (16-bit color) or higher screen display Windows 2000 / Windows XP / Windows Vista Compatible interface USB, LAN Standard functions Review saved data, real-time capture of PC data, main unit setup, CSV file conversion Waveform operation Direct operation of waveform by mouse or Change CH scales individually by icons icons, Batch processing of selected waveform Waveform display Display graphs in multi-window, X-Y View, FFT View, Handy function of switching waveform, Display in single window, X-Y View between Cursors (only during Display function of grouping channel, Scrolling replay), Display function of grouping channel for all directions (up, down, right, left) Configuration function Advanced channel grouping function, Advanced Listview setup function, Main unit setup Channel grouping fuction, Main unit setup External control of sampling − Available (can set and display) Captured data Binary file (original format): Captured data and the information of graph window are saved. CSV file: Captured data is saved in comma-separated value format: Binary files can be converted to CSV files all at once Others Cursor function, Comment Input function, Excel transfer function Note: 1. Even when using a PC with adequate specifications, capture errors occur at times because the PC is in bad condition. (For example, when other applications are open, or recording medium has no free area.) When you capture data using this software, please close all the other applications and save captured data to the hard disk. 2. Don’t start up other applications while this software is operating, and don’t perform multiple operations. (For example, screen saver, virus scan program, copying and moving files, searching files, etc.) 3. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. 4 ZR-RX System Configuration Standard set [email protected] ● Main unit ● AC adapter/AC cable ● User’s manual ● Utility disk* [email protected] * Content of utility disk –Standard PC software: Smart Viewer RX70 –Special PC software: Wave Inspire RX (Trial version) –Manual PDF file ● Main unit ● AC adapter/AC cable ● User’s manual ● Utility disk* [email protected] * Content of utility disk –Standard PC software: Smart Viewer RXW –Special PC software: Wave Inspire RX (Trial version) –Manual PDF file ● Main unit ● AC adapter/AC cable ● User’s manual ● Utility disk* * Content of utility disk –Standard PC software: Smart Viewer RXW –Special PC software: Wave Inspire RX (Trial version) –Manual PDF file Option [ZR-RX common] Special PC Software ZR-SX10 DC Cable (2 m) ZR-XRD1 Battery Pack ZR-XRB1 Logic Alarm Cable (2 m) ZR-XRL1 Humidity Sensor (3 m) ZR-XRH1 [ZR-RX45 common] Base Set ZR-XRE1 Extension Terminal Set ZR-XRT1 Cable (Accessory, 0.5 m) [For ZR-RX70] ZR-RX45 Necessary option when channel is enhanced Item BNC-Crocodile Cable (2 m) ZR-XRC1 20 CH 40 CH 100 CH 200 CH ZR-RX45 Main unit 1 1 1 1 Base Set (ZR-XRE1) 0 1 1 1 Extension Terminal Set (ZR-XRT1) 0 1 4 9 Safety Precautions WARNING This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Precaution for Correct Use Do not use the product in ambient atmospheres or environments that exceed the ratings. For technical information and product FAQs, refer to the “Technical Guide” on your OMRON website. 5 ZR-RX (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified. ZR-RX70 ZR-RX45 232 24.6 32 122 120 3.5 48 2 232 75 5 ZR-RX70 Mounting Screw Holes 2-M4 Depth 6 ZR-RX45 Mounting Screw Holes 2-M4 Depth 6 69 23.5 185 ZR-RX25 16.5 162 91.6 16.1 15 102 67 194 2-M4 L5 Insert Screw 40 2 6 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2013.7 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2013 All Right Reserved.