PT9300-SDI-IR-10X
HD-SDI Infrared Mini high speed dome
Operation and Installation Manual
TABLE OF CONTENT
1. Precaution----------------------------------------------------------------------------------------------------1
2. Performance-----------------------------------------------------------------------------------------2
2.1 PTZ t echnology parameter --------------------- -------------- ------------------------------------------2
2.2 Camera parameter----------- ----------------------------------------- --- - ----------------------------- 2
2.3 Performance & Feature ----------- -------------------------------------- ------------------------------------- 3
3. Function and instruction ------------------------------------------------------------------------------------4
3.1 Auto-run motion ----------- ---------------------- ---------- ---------- ---- -------------------------------4
3.2 Camera control ------------- ------------------------- - -- -- ----------------------------------------------------------5
3.3 Monitor function------------------- ------------------------------------ ------------------------------------------5
4. System setting------------------------------------------------------------------------------------------------7
4.1 Basic operation ------------------ -------------------------- ------ -----------------------------------------7
4.1.1 Self-testing ------- ------------------ --- ------- -- -- -------------------------------------------------7
4.1.2 Call the main menu ------------------------------------- - -------- --------------------------------7
4.1.3 Menu and keyboard operation-----------------------------------------------------------------7
4.2 Edit dome label ----------- ------------------------- ------- - -- -------------- -------------------------------------8
4.3 Display initial information ------------ ------------------------------- ---------------------------------9
4.4 Display setup --------------- ------------------------- - ------------------- ------------------------------10
4.5 System motion control -- ---------------------------- ----------- ---------------------------- -----------11
4.5.1 Auto flip ------------ ------------------------- ------------------------- --------------------------- 11
4.5.2 Speed proportion pan------------- --------------------------------------------------------------- 11
4.5.3 Park action---- --------- ------------- --------------------------------------------------------------12
4.5.4 Power up action-------------- ------------------------- ---- ------------------------------------- 12
4.5.5 Fan startup by temperature-------------- ------------------------- ---- ------------------------ 12
4.5.6 Advance setting--------------------------------------------------------------------------------13
4.6 Clear and restart ---- ------------------ - ------- -------------------------------------------------------- 14
4.7 Password set---------------- ------------------ - ------- --------------- ---------------------------------- 15
4.8 Time set ---------------- ------------------ - ------- --------------- -------------------------------------- 16
4.9 Setup dome parmeter---------------- ------------------ - ------- --------------- ------------------------- 17
5. Camera setting-------------- --------- ----------- -------------------------------------------------------- 18
5.1 Zoom speed------------------- ------------------------------------------------------------------------ 18
5.2 Digital zoom control ------------- --------------------------------------------------------------------- 19
5.3 Back light compensation ----------------------------------------------------------------------------20
5.4 Slow s hutter control ----------------------------------------------------------------------------------21
5.5WDR control----------- ------------------ ---- ------- - --------------- ----------------------------------22
5.6 Video output setting----------- ------------------ ---- ------- - --------------- --------------------------22
5.7 Advance setting --------------- ----------------------------------------------------------- ---------23
5.7.1 Day/night mode ------------------------------------------------------------------------------23
5.7.2 AE mode ---------- ---------------- ----- -------------------------------------------------------24
5.7.3 White balance mode ---------- ---------------- ----- ------------------------------------------24
5.7.4 Image setting function---------- --------------------- ----------------------------------------25
5.7.5 Focus mode ---------- ---------------- ----- ----------------------------------------------------25
6. Function setting ------------------------------------------------------------------------------------------26
6.1 Preset ---------------------------- ------- ------- --- ----------------------------------------------------- 26
6.2 Scan -------------- --------------------------------- ----------------------------------------------------- 27
6.3 Pattern ---------------- --------------------------- --------- --------------------------------------------- 28
6.4 Tour------------ --------------------- -- ------- -------------- ------------------------------------------29
6.5 Zone ---------------- ---------------------------- --- ----------------------------------------------------30
6.6 Time running---------------- ---------------------------- --- ------------------------------------------31
7. Privacy zone masking------------------------------------------------------------------------------------32
8. Alarm function--------------------------------------------------------------------------------------------33
8.1 ARM setting-----------------------------------------------------------------------------------------34
9. Appendix ----------------------------------------------------------------------------------------------------35
9.1 Menu index-----------------------------------------------------------------------------------------35
9.2 Rs485 Bus Basic Knowledge----------------------------------------------------------------------36
10.Installation --------------------------------------------------------------------------------------------------38
10.1 Caution--------------------------------------------------------------------------------------------------38
10.2 Distributing the Line in Security----------------------------------------------------------------------38
10.3 Lightning Proof and Surge Proof ----------------------------------------------------------------------39
10.4 Water Proof ----------------------------------------------------------------------------------------------39
10.5 The preparation of installation------------------------------------------------------------------------39
11. Installation instruction --------------------------------------------------------------------------------------40
11.1 Wall mount installation ---------------------------------------------------------------------------------41
11.1.1 wall bracket installation -------------------------------------------------------------------------41
11.2 Pendant mount installation -----------------------------------------------------------------------------42
11.2.1 Pendant bracket installation---------------------------------------------------------------------42
11.3 installation instruction ----------------------------------------------------------------------------------43
11.3 Electrification inspection ------------------------------------------------------------------------------43
12.Maintance service terms--------------------------------------------------------------------------------------44
Precaution
1. Precaution
Ø
Electrical safety
Conform to country and local electrical safety standard when using or installing the product.
Ø Transportation
The PTZ should be protected against extremes of pressure, vibration and humidity during storage
installation and transportation. The infrared PTZ camera is transported by integrated packing.
Ø
Installation of care
Please refer to user installation manual when installation. Please pick up the Infrared parts gently
and do not press it, or else, which will cause the malfunction of parts; the lens of Infrared belong to
optional products, please do not touch it by your hand to avoid scraping it.
Ø Requirements
to service personnel
All the service work should be done by qualified technicians.
Ø Do
not disassemble the pan/tilt module
Do not disassemble screws, and don't maintain the parts in the Pan/Tilt by yourself. Only qualified
and authorized personnel can undertake repairs.
Ø Environmental
requirements
= Requirements for PTZ:
Environmental temp:-30 C ~ +50 C
O
O
Humidity:<90%
Air pressure:86~106Kpa
Power supply:AC 24V/1250MA,50/60HZ
Ø
Don't place the camera to be shoot by strong light objects
Don't place the camera to be shoot by strong light objects. Don't point the PTZ to the sun or other
bright objects when in use or not. It may affect image quality.
Ø
Function of waterproof
Our product has good water-proof, humidity-proof and dust-proof, which pass the standard of IP66.
But it's not good to stay in the humidity environment, which will make some machinery parts broken.
1
Performance
2. 1 Technology parameter
Electrical:
Setting:
AC 24V
Power supply
Consumption
(PTZ+IR light)18W
(PTZ+IR light+Heater)24W
Decoder
Built-in
Operation:
Baud rate(RS485)
2400/4800/9600/19200bps
Protocol
Sixteen protocols, including Pelco,
Kalatel, Phlips, Diamond, etc.
Address setting
0-254
Environmental:
Pan rotation
360°continuously
Operational environment
-30℃~ +50℃
Tilt rotation
Tilt105°,with auto flip
Environmental humidity
0—95% no compensation
Rotation speed
Pan0.4~240°
/S
Protection grade
IP66,Weather proof housing,
4000Vlightning proof surge proof
Preset
128presets
Physical:
Surveillance
Preset、Tour、Scan、Pattern
Mount
wall mount/pendant mount
Alarm function
4 alarm input/1 alarm output
Infrared night vision
Above 50 meters
Tilt0.4~120°
/S
2. 2 Camera parameter
Spec
2
Model
MUS: 3x
(SE600)
Imaging element
1/2.8 Type Exmor CMOS Sensor
Scanning system
Progressive scanning
Effective pixel (H×V)
2 Mega pixel
Minimum illumination
0.25lux/0.03lux
Zoom
3x optical,12x digital
Focus
3-9(mm)
IRIS control
Auto/Manual
Focusing system
Auto/Manual
White balance
Auto/Manual
Back -light compensation
Off/No
WDR control
Yes
S/N ratio
〉50dB
Wide Dynamic Range
Off/No/Auto
Privacy zone masking
No
Performance
2.3 PTZ Performance and Feature
The intelligent Pan/tilt was complete new design, compact structure, built-in constant temperature
device and rapidly heat dissipation from chip; Infrared LED; Camera rotate flexibly with low noise,
wide capture range and certain auto-functions can provide perfect quality of image for customer.
Ø Built-in
receiver
●
All configurable options stored in main control board to protect against power cuts
●
Integrate design and high durability
●
1-80preset support auto-tour, and each tour can store up to 24 presets.
●
4 pattern tours
●
4 scan
●
Built-in direction indicator
●
Built-in temperature indicator
●
Built-in clock setting function
●
Rs485 Bus communication or American Dynamics Manchester code
●
Support 24 masking zones at most(This function is decide by the parameter of built-in camera, if the camera
●
128 presets can be randomly stored
has no this function, this option is invalid. )
●
4 alarm input, 1 alarm output.
Ø Pan Tilt Feature
Aluminum alloy material and anti-violence design surface is well hidden and rapid heat removal; Level
●
of protection achieves IP66.
●
Precise stepping motor drives the pan to run smoothly and react sensitivity.
●
Integrated design, compact structure, easy to disassmeble.
●
Exquisite mechanical drive, support to rotate pan 360°continuously and tilt -15°~ +90°, and may
rotate 180°with auto flip.
●
Pan 0.4°/s to rotate slowly, and the image will not vibrate.
Ø Built-in
digital camera
●
High sensitivity, high resolution, and integrated digital processing
●
Auto-focus
●
Auto-Iris
●
Auto brightness control
●
Auto white balance
●
IR cut filter
●
Auto back light compensation
●
Auto slow shutter
Ø
●
●
OSD menu
All English menu can be selected.
Visual OSD menu. Revising the PTZ's information and parameter by keyboard and OSD menu,
and it is easy to operate.
●
Set park action function and set presets, or run scan, pattern, tour, etc during idle time.
●
Auto-resume movement or carry out pointed movements after power up.
3
Performance
Ø
Internal temperature test
Set time display
● When the temperature exceeds the limit, the screen will display alarm information.
● When the temperature is under the limit, the PTZ will delay to startup, and when the heat device
is heated and got higher than low limit temperature to startup.
● According to the temperature, the fan measures if it is to start or not, and prolong the life of fan.
●
Ø
Time running
By the menu “Time running”,user may set time running function everyday, and set different four
actions in four different time in one day, including preset, scan, pattern and tour.
Ø
Night View Function
Infrared LED range more than 50 meters, can manual control or auto-control infrared LED ON/OFF,
manual control through keyboard can turn infrared LED ON/OFF. If auto-control working, image color
will be switch to black and white when in low brightness, black and white will be switch to color when in
high brightness.
3. Function Instruction
This passage mainly describes the main function and general principle of intelligence PTZ, and not
refer to the concrete operation methods. Different system platform has different operation methods, generally,
should according to the system manufactory's operation manual. Please contact dealer to get necessary
information, there are some particular requirements and operations under specific condition.
3.1 Auto-run motion
Ø
Focus/speed proportion pan
When manually adjusting, for far focus situation, the PTZ responds at a high-speed so that touching
rocker slightly may make picture move rapidly, thus cause the picture to lose. To base on humanized design,
the PTZ automatically adjust pan and tilt rotation according to zoom near and far, which make it is
convenient to operate manually to make tracking for the object. In the menu, you may change system
parameter setting proportion pan as ON to run this function.
Ø
Auto flip
If user holds the joystick in the down position, the camera rotates pan 105 degrees, then t he camera
rotates tilts up to 180 degrees . In the menu, you may set the system parameter setting AUTO FLIP as ON
to run this function.
Ø
Park action
By the menu“ park time” and “park action ”, user may set auto-call preset or run tour, pattern, and
scan, etc after pointing a few minutes if the PTZ doesn't run any motions.
Ø
Power up action
By the menu“ power up action”, after the PTZ powers up or restarts, user may set auto- resume
movements before power up and auto- call preset or run tour, pattern, and scan etc .
4
Function Instruction
3. 2 Camera control
Ø Magnification control
The user can control“Wide/Tele” to adjust zoom far and near of the image by keyboard controller to obtain
panoramic image or close view that you need. The PTZ support digital zoom and optical zoom.
Ø
Focus control
System defaults Auto focus. When the lens changes, camera will auto-adjust focus according to the center of
the image to get legible image; user can also manually focus to get desire image by operating keyboard
“FAR/NEAR”. When operating keyboard joystick, camera resumes to auto focus.
The camera cannot auto focus in the following status:
●Target is not the center of the image
●Observation the target near and far at the same time, can not be clear at the same time.
●Target is a strong light object, such as neon light, spotlight , etc.
●Target moves too fast
●Target area such as wall
●Target is too dark or vague
●Target image is too small
Ø
Iris control
System defaults Auto Iris. Camera can rapidly adjust size of Iris, through the automatically induct the changing
of environment ray, and thus make the brightness of deferent image stable.
User may adjust Iris by controller keyboard “open/close” to get required brightness that you need. User also
can resume auto Iris by joystick operation. When controlling the Iris manually, the PTZ locks current position you
manually controlled; when operating joystick, the PTZ resume auto Iris.
Ø
Auto back light compensation
Camera sub-area can carry out auto back light compensation. Under a strong light background, camera will auto
compensate light for the darker object and adjust daylight to the bright background. In order to avoid making the
image lack fidelity by the back line is too bright, and the object is unable to recognize because of darkness, thus gain
legible image.
Ø
Auto white balance
Camera can automatically adjust white balance in accordance with the alteration of background lightness
to reach a true colour.
3. 3 Monitor function
Ø Set and call preset
Preset function is that PTZ stores current pan/tilt angle, zoom and other position parameters into the memory.
When necessary PTZ recalls these parameters and adjust camera to that position. User can store and recall presets
easily and promptly by using keyboard controlling. The PTZ can store up to 128 presets.
Ø
Tour
Auto tour is the built-in function in the PTZ, to make preset arranged in needful order in tour queue
by programming in advance. To make camera tour between presets by inserting presets in cruise tour. It is feasible
to program tour order, each time as you run tour, you can set the park time of preset. A tour can store 24 presets.
5
Function Instruction
Ø
Scan
The operator can prompt set right limit and left limit in advance by keyboard and menu, so as to make
the camera repeatedly scanned between right and left limit at a setting speed.
Ø
Pattern
Pattern is built-in function in camera; the PTZ can record tracks that are no less than 180s, when running
pattern, the PTZ moves repeatedly according to the recorded tracks. A PTZ can set up to 4 pattern tours.
Ø
Lens position display
The position that the PTZ has finished to auto-checking as 0 point of pan movement and tilt movement.
The pan range is 0-360°, and tilt range is 0°~ +105°. According to the displayed information, to set the
position of camera lens, and the position can display on the screen.
6
System Setting
4. System setting
4. 1 Basic operation
4. 1. 1 Current-carrying to PTZ and Self-testing
The PTZ conducts self-testing after current-carrying , and it rotates slowly until displaying pan origin
that is default setting, then moving to tilt origin, the lens is adjusted from far zoom to near zoom, then from
near zoom to far zoom, when self-testing is finished, there is relevant system information displaying on the
screen, as follow:
Soft edition
Protocol
PTZ ID
Communication parameter
The information will not disappear until you stop to operate the system. If you set“power up action”,
the PTZ will automatically activate motions after self-testing. How to operate the function? We will explain
detail introduction in following passages.
4. 1. 2 Call the main menu
The system enters into the main menu by calling 95 preset or by calling 9 preset twice within 3 seconds.
All the menu setting must enter into the main menu at first.
4. 1. 3 Menu and keyboard operation
Ø Keyboard operation:
【OPEN】 when choosing pictures, it means to increase Iris; when setting menu, it means to enter into the
next menu or setting, or means to save after setting .
【CLOSE】when choosing pictures, it means to reduce Iris; when setting menu, it means to exit without
saving setting.
【NEAR】 Focus to near
【TELE】Increase magnification
【WIDE】Reduce magnification
Joystick to up: When choosing menu, it means to choose the former one; when choosing picture, it
means camera tilt up.
Joystick to down: when choosing menu, it means to choose the next one; when choosing picture, it
means camera tilt down.
Joystick to left: when choosing menu, it is equal with【CLOSE】, when choosing picture, it means
camera tilt left .
Joystick to right: when choosing menu, it is equal with 【OPEN】, when choosing picture, it means
camera tilt right.
Press【TELE】and 【WIDE】at the same time, it means 3D joystick rotates joystick cap.
Ø
Menu operation
“BACK” : Back to the former menu
“EXIT” : Exit to menu
“ ON” : Open some setting
“OFF ” : Close some setting
7
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
4. 2 Edit dome label
When using a lot of PTZs’systems, in order to identify each PTZ,
the systems support title setting. The setting ways as follow:
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Moving joystick up and down to move the cursor to【SYSTEM SETTING】,
and pressing【OPEN】to enter into the next menu.
3、 Moving joystick up and down to move the cursor to【EDIT PTZ
LABEL】, and pressing 【OPEN】 to enter into the label setting menu.
4、Moving joystick up/down to move the cursor to【LABEL】, and
pressing 【OPEN】to edit current label.
SYSTEM SETTING
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
EDIT DOME LABEL
LABEL: SPEED DOME
BACK
EXIT
8
5、When the cursor is twinkling in the first character of the label, to move
joystick to choose character, after editing, pressing【OPEN】to save.
6、Moving joystick to【 BACK】and pressing【OPEN】to back to the
former menu.
The label may set 16 characters, and doesn't need editing
characters. Pressing 【OPEN】 continuously to jump over and
using spacebar to replace the deleted characters. When you finish
to editing character, press【OPEN】 to enter into the next editing
character; when you editing the last character, pressing 【OPEN】
to save. Press 【Close】 to exit.
Characters of label available for choosing are as follow: 0- 9,
A-Z,:<>-., Space.
Other labels’ input ways are the same as above.
System setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
4. 3 Display initial information
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】 to
enter submenu.
3、Tilt up/down joystick to 【INITIAL INFO】, press【OPEN】 to display
initial information as left picture shows.
Initial information includes soft edition, Protocol, PTZ ID, communication
SYSTEM SETTING
parameter. System setting may change the numerical value of initial information.
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
INITIAL INFO
FIRMWARE
V1.10
PROTOCOL:PELCO
DOME ADDRESS: 001
COMM:2400,N,8,1
BACK
EXIT
9
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
SYSTEM SETTING
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
4. 4 Display setup
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】 to
enter submenu.
3、Tilt up/down joystick to【DISPLAY SETUP】, press 【OPEN】to enter
“display setup” menu, May setting the content of the display setup as
follow:
● 【DOME LABEL】
● 【PRESET LABEL】
● 【ZOOM LABEL】
● 【ZONE LABEL】
● 【DIRECTION LABEL】
● 【TEMPERATURE LABEL】
● 【TIME LABEL】
● 【DATE LABEL】
4、 Taking display PTZ label as an example to explain the operation process. Tilt up/down joystick to move cursor to 【Dome LABEL OFF】, press
【OPEN】, there is a sign “ ” besides【Dome LABEL】, the cursor is
twinkling besides 【OFF】, as left picture shows;
5、Joystick tilt up/down, setting number changes between ON/OFF, when
setting 【ON】, it means to display“PTZ label”; when setting 【OFF】,
it means not to display “PTZ label”.when p ressing 【 OPEN】, the cursor
jump back in front of 【DOME LABEL】, means label setting is finished,
when moving the cursor to 【EXIT】, it means exiting the menu setting.
DISPLAY SETUP
DOME LABEL
OFF
PRESET LABEL
OFF
ZOOM LABEL
ON
ZONE LABEL
OFF
DIRECTION LABEL ON
TEMPERATURE LABEL OFF
TIME LABEL
ON
DATE LABEL
ON
BACK
EXIT
The displaying information on the screen will change with the PTZ
rotation; Through the information on the screen, user can see current PTZ
inside temperature, magnification, display zone etc. When all the label are
displayed, the PTZ works as the following picture shows,:
(In the picture “305” means pan angle, “45” means tilt angle. )
PTZ label
Preset setting
Zone label
Direction label
Temperature label
07/12/06
17:39:10
Zoom magnification label
10
Date label
Time label
System setting
SYSTEM SETTING
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PA SSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
4. 5 Systematic motion control
Systematic motion controlling may control a series of canonical movement of the PTZ, and play an important role in controlling the PTZ.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to【SYSTEM SETTING】, press【OPEN】to enter submenu.
3、Tilt up/down joystick to 【MOTION】, press 【OPEN】 to enter systematic motion controlling menu, as left picture shows.
4. 5. 1 Auto flip
MOTION
AUTO FLIP
PROPORTION PAN
PARK TIME
PARK ACTION
BOOT ACTING
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
EXIT
ON
ON
005
SCAN
AUTO
050
CENT
Press 【OPEN】 to save .
REMARK: When opening the auto flip function, user holds the joystick in the
down position, the camera rotates pan 180 degrees, tilt up to 105 degrees.
4. 5. 2 Speed proportion pan
MOTION
AUTO FLIP
PROPORTION PAN
PARK TIME
PARK ACTION
BOOT ACTING
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
EXIT
1、Operate joystick, move the cursor to【AUTO FLIP】: press 【OPEN】
to enter“ auto flip ”setting, tilt up/down joystick, for example: choosing
"ON" to open“ auto flip”; choosing "OFF" to close“auto flip”.
ON
ON
005
SCAN
AUTO
050
CENT
1. Operate joystick, move the cursor to【PROPORTIONAL PAN】; press
【OPEN】 to enter“ proportion pan” setting, tilt up/down joystick to choose, if choosing 【ON】, it means to open proportion pan; if choosing
【OFF】, it means to close proportion pan , press 【OPEN】to save.
OPERATION KNACKS
When manually adjusting, for far focus situation, the PTZ
responds at a high-speed so that touching joystick slightly may
make picture move rapidly, thus cause the picture to lose. To
base on humanized design, the PTZ automatically adjust pan
and tilt rotation according to zoom near and far, which make it
convenient to operate manually run after object.
11
System Setting
4. 5. 3 Park action
MOTION
AUTO FLIP
PROPORTION PAN
PARK TIME
PARK ACTION
POWER UP ACTION
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
EXIT
ON
ON
005
SCAN
AUTO
050
CENT
1、 Operate joystick, move the cursor to 【PARK TIME】, press 【OPEN】
to tilt up/down joystick to set park time, the range is 0-240 (minute), press
【OPEN】 to save.【PARK ACTION】 is running action at park time, when
【PARK TIME】 sets as 0, this item can't be set.
2、Operate joystick, move the cursor to 【PARK ACTION】, press 【OPEN】
there will be a sign
in the front of 【PARK ACTION】, the cursor jump
to right, after tilt up/down joystick to choose“ park action ” ,there are
options for choosing as follow, press 【OPEN】 to save.
● 【NONE】- (default) none action
● 【PRESET】 - use preset 1-80
● 【SCAN】 - run scan
● 【PAT1】 - run pattern X
● 【TOUR】 - run tour
MOTION
AUTO FLIP
PROPORTION PAN
PARK TIME
PARK ACTION
BOOT ACTING
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
EXIT
This setting allows the PTZ to run an appointed action after it enters
vacancy for a few time (1-240minutes). If default sets as 0, it means not to
run this action automatically.
ON
ON
005
SCAN
AUTO
050
CENT
4. 5. 4 Boot acting
The PTZ start to run actions after self-testing, if nobody intervenes
it , it will repeatedly run this action continuously , if default sets as
【NONE】.
1. Operate joystick, move the cursor to 【BOOT ACTING】: press
【OPEN】 to jump to the following choice, tilt up/down joystick to choose
“power up action”, press 【OPEN】 to save.
● 【NONE】 - none action
● 【AUTO】 - the PTZ resumes the primary action and direction
before power up.
● 【PRESET】 - use preset 1
● 【SCAN】 - run scan
● 【PAT1】 - run pattern
● 【TOUR】 - run tour
MOTION
AUTO FLIP
PROPORTION PAN
PARK TIME
PARK ACTION
BOOT ACTING
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
EXIT
12
ON
ON
005
SCAN
AUTO
050
CENT
4. 5. 5
Fan startup by temperature
The temperature of the PTZ will rise when it is in high temperature. The
fan will open automatically when the temperature reaches to a very high degree
value in order to make sure the stability of the PTZ.
Operate joystick, move the cursor to 【FAN ENABLED】: press【OPEN】 ,
the cursor will skip to the back option. The user can choose the fan to start up
temperature, and press【OPEN】 to save it in actual condition.
The default setting temperature of the fan startup is 50 C. The user
also can enter into the fan startup setting to adjust the temperature of fan
O
startup. As picture shows: the temperature range is 0-60 C.【TEMP】can
switch the temperature between fahrenheit and centigrade.
O
System setting
4. 5. 6 Advance setting
MOTION
AUTO FLIP
PROPORTION PAN
PARK TIME
PARK ACTION
POWER UP ACTION
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
EXIT
ON
ON
005
SCAN
AUTO
050
CENT
ADVANCE SETTING
EIS ENABLED
PRESET FREEZE
AUTO FOCUS
DEFOGGER
A D J SPEED
IR HEADLIGHT
SPECIAL SETTING
BACK
EXIT
N/A
N/A
OFF
10
100
IR HEADLIGHT
MODE
DELAY TIME
BW
ACT. AUX1
LED 1
LED 2
LED 3
LIGHT
BACK
EXIT
MID
002
AUTO
OFF
100
200
×
×
SPECIAL SETTING
GRID
POS.MODE
ZERO AZI
BACK
EXIT
ON
MODE1
1.Operate joystick and move to【ADVANCE SETTING】, press【OPEN】
to enter into "advance setting";
【EIS ENABLED】: Electronic Image Stabilizer function;
【PRESET FREEZE】: Function of Preset Freeze means during
calling presets, the monitor displays the image before call presets, and
releases the freeze image when camera arrives the appointed presets.
【AUTO FOCUS】: when choosing 【ON】,enable the camera to auto
focus; when choosing【OFF】,enable manually focus.
【DEFOGGER】: Lens of PTZ will be fogged when PTZ works in
quite cold temperature. In order to get clear image, defogger will open
automatically at the appointed temperature. Choosing 【DEFOGGED】by
operating the joystick, and press 【OPEN】, then cursor leap to the optional.
Choose the temperature to run the defogger, and press 【OPEN】to save.
Range of Temperature: 0~30℃.
【ADJ SPEED】:The rotation percentage of P/T, 100 means factory
speed, 80 means 80% of factory speed.
【MODE】: Setting of Infrared light. Call 62 preset to run infrared light
under the setting of【MANUAL】. Save 62 preset to close the
infrared. The default setting of infrared light is Auto MID.
【DELAY TIME】: Setting the auto close time of IR light, ranging from
1-240 Minutes.
【BW】:Setting the imaging model after the IR light as ON, three modes
for choice: Auto, Color, Black.
【ACTIVATE AUX1】Whether to link AUX 1 when open the IR light,
“On”means Link. “OFF” means not to link.
【LED 1】For LED brightness adjustment, range:50-200, Brightness
increase in proportion as bigger digits is chosen.
【LED 2/LED 3】Same as the above
【LIGHT】Options of light sources
(Temporarily unavailable)
SPECIAL FUNCTION SETTING:
【SPECIAL SETTING】 special function setting
【GRID】location function
【POS.MODE】 Position mode, enable displaying the rotate direction. When
Dome rotate in a clockwise direction, “MODE1”horizontal numerical value
will decrease, “MODE2” horizontal numerical value will increase.
【ZERO AZI】Setting the “0” azimuth angle; call 180 preset to enable swiftly
setting the “0” azimuth angle.
OPERATION KNACKS
1.After the PTZ set the EIS function, if the PTZ wobble slight when running,
the camera will shield the wobble picture and make the picture calm and smooth.
2.When start-up preset freeze, it can eliminate the sense of flash caused by
calling presets when open function of Preset Freeze, which can reduce the
storage space of DVR if image is stored by DVR.
These function in the advance setting menu depends on the models
and parameters of built-in camera in PTZ, if the camera haven't this
function, then this function is invalid. The option is useless (N/A)
when the camera module has no such function.
13
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
4. 6 Clear and restart
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【SYSTEM SETTING】, press 【OPEN】to
enter submenu.
3、Tilt up/down joystick to 【CLEAR】, press 【OPEN】to enter submenu,
as left picture shows.
● 【CLEAR ALL ZONES】
● 【CLEAR ALL PRESETS】
SYSTEM SETTING
● 【CLEAR ALL PATTERNS】
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PA SSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
● 【CLEAR ALL TOURS】
● 【CLEAR ALL WINDOWS】
● 【FACTORY DEFAULTS】: resume the factory default. Run this function, the camera parameter and system parameter will resume to factory default,
clear all windows and alarm setting. Please be cautious to use this function .
● 【RESTART】
4、Set clear zone as an example to explain the process. Tilt up/down joystick to 【CLEAR ALL ZONES】, press【OPEN】to clear all zones.
CLEAR
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
CLEAR ALL WINDOWS
FACTORY DEFAULTS
RESTART
BACK
EXIT
14
Once clear all commands in the controlling menu,
it cann't resume, so please be careful of using it.
System setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
4. 7 Password set
1. The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2. Operate the joystick up and down, move the cursor to 【SYSTEM
SETTING】 , press 【OPEN】 to call the submenu.
3. Operate the joystick up and down , move the cursor to 【PASSWORD
SETUP】, press 【OPEN】 to call the submenu. Please refer to the left
picture.
4. Operate the joystick up and down , move the cursor to 【OLD
SYSTEM SETTING
PASSWORD】, press 【OPEN 】to choose it, operate the joystick right and
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
left to input the password, Tilt up and down to choose the number which you
need.
● 【NEW PASSWORD】 Enter the new password
● 【CONFIRM PASSWORD 】 Confirm the new password
● 【ENABLE PASSWORD 】Set PASSWORD off / on
(The password function is nonreflective under the PASSWORD OFF.)
It means that users can enter into the main menu without password.
(The password function is effective under the password ON.) It means that
user enter into the main menu with password.
PASSWORD SETUP
OLD PASSWORD:******
NEW PASSWORD:******
CONF PASSWORD:******
ENABLE PASSWORD:OFF
When user forgot the password and can not enter into the
BACK
main menu, he can use the super password to enter ,which
is "892226",At this time ,the password of PTZ will
EXIT
change to initial one, which is "000000",and then user can
set the password by himself again.
15
System Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
4. 8 Time set
1. The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2. Operate the joystick up and down, move the cursor to 【SYSTEM
SETTING】 , press 【OPEN】 to call the submenu.
3. Operate the joystick up and down, move the cursor to 【CLOCK
SETTING】 , press【 OPEN 】to call the submenu. Please refer to the left
picture.
4. Operate the joystick up and down, move the cursor to【TIME】, press
SYSTEM SETTING
【 OPEN】 to choose it, move the joystick up and down to choose the
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
number you need, move the joystick right and left to set hour, minute,
CLOCK SETTING
TIME
03:20:18
DATE
07/10/10
DAY
WED
BACK
EXIT
16
second.
● 【DATE】set year, month, date;
● 【DAY】 set week;
● 【BACK】return to the former menu;
● 【EXIT】 exit the main menu.
System setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARM
EXIT
4. 9 Setup Dome parameter
1.The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2.Click the up and down button to move the cursor to 【SYSTEM SETTING】,
and click the right button to enter into the next menu.
3.Click the up and down button to move the cursor to 【COMM SETTING】,
and clicking the right button to enter into Dome parameter setup
menu.
S/N: Show Series NO. of the dome ex-work.
SYSTEM SETTING
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
CONF : Using to edit, the series NO. of the dome is the same as S/N
series Number.
SITE ID: Setting up the ID Number of the dome, address scope (001-255).
COMM SPEED: Baud rate setup. The user can choose 4 kinds of Baudrate (2400 BPS, 4800 BPS, 9600 BPS, 19200 BPS).
PROTOCOL:set protocol,the user can choose 16 kinds of protocol:
PELCO 、FACTORY、 DYNACOLOR、 ISD、 HUNDA、 VIDO B02 、
LILIN、KALATEL、 DIAMOND、 SAMSUNG 、PANASONIC、
SANTACHI、 VICON 、MOLYNX、 VCL 、SAE.
COMM SETTING
Remark: below operation can not be continue when above
two series Number are not the same.
S/N: 4JKAA7824000058
CONF: 4JKAA7824000058
SITE ID
001
COMM SPEED 2400BPS
BACK
EXIT
17
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
5. Camera setting
5. 1 Zoom speed
1、The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2、Tilt up/down joystick to【CAMERA SETTING】 , press 【OPEN】to
enter submenu;
3、 Operate joystick, move the cursor to 【ZOOM SPEED】; press【OPEN】
will appear a sign " " in the front of 【ZOOM SPEED】, the cursor moves to
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
EXIT
18
right, tilt up/down joystick to choose 【HIGH】 or 【LOW】 ;
4、 Press 【OPEN】 to save, press 【CLOSE】 to cancel.
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
5. 2 Digital zoom control
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Tilt up/down joystick to 【CAMERA SETTING】, press 【OPEN】 to
enter camera setting;
3、Operate joystick, move the cursor to 【DIGITAL ZOOM】, press 【OPEN】 to enter digital zoom setting, tilt up/down joystick, to choose ON means
open digital zoom control which is digital zoom is pulled near, if pulling the
digital zoom near again, the PTZ enters into“ digital zoom increase”; to
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
EXIT
choose OFF means to close digital zoom control .
4、Press【OPEN】 to save.
OPERATION KNACKS
When digital zoom be set as ON, the maximum zoom magnification of the PTZ is digital zoom magnification times optical
zoom magnification; when digital zoom be set as OFF, the maximum
zoom magnification of the PTZ is optical zoom magnification.
The option of the digital zoom is ON/OFF when the camera
module is SONY 、LG、CNB、HITACHI .
19
Camera Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
5. 3 Back light compensation
1、The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds.
2、Operate joystick, move the cursor to 【CAMERA SETTING】 to enter
submenu.
3、Operate joystick, move the cursor to 【BLC MODE】, press 【OPEN】,
There will be a sign
in the front of【BLC MODE】, the cursor jump to
right, tilt joystick to open or close back light compensation function. If choosing ON means to open back light compensation mode; if choosing OFF means to close back light compensation mode;
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
ON
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
EXIT
4、Press 【OPEN】 to save.
OPERATION KNACKS
Strong background ray can make backlighting objects engender
shadow, (back light compensation), the PTZ can auto-adjust iris to
match with the changes of various ray, and auto-revise the main
lightness to make the pictures more legible.
This function relates to models and parameters of the built-in
camera in the PTZ, when open black compensation, it has two
functions which are auto-adjust (when you choose ON) or
manual adjust(0-255) according to the different of the camera.
Non-use back light compensation, in
strong sunshine, the back light side is
subject to dark.
20
Use back light compensation, the
image is in gear.
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
5. 4 Slow shutter control
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate joystick, move the cursor to【CAMERA SETTING】 to enter
submenu.
3、Operate joystick, move the cursor to【SLOW SHUTTER】, press
【OPEN】, there will be a sign
in the front of 【SLOW SHUTTER】,
the cursor moves to right, tilt up/down joystick to “slow shutter” choice,
if choosing ON means to open slow shutter function, if choosing OFF means
close “slow shutter”function.
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM ON
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
EXIT
4、Press【OPEN】to save.
OPERATION KNACKS
When the PTZ monitors at night or dark environment, because
the ray is not enough, the image on the screen is too dark, setting slow
shutter can lengthen the time of lighting so that make the picture that
is shooted in dark more legible.
This function depends on the models and parameters
of built-in camera in PTZ, if the camera haven't this
function, then this function is invalid.
21
Camera Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
5. 5 WDR Control
1. The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2. Operate joystick and move the cursor to【CAMERA SETTING】, press
【OPEN】, Enter the next main menu
3. operate joystick and move the cursor to【WDR MODE】 , press 【OPEN】,
tilt up/down joystick to set WDR. Choice ON is open WDR Function, choice
off is closed WDR, if you choice Auto, Than mean Auto setting WDR.
4. Press 【OPEN】 to save.
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
OFF
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
This function is relative with the model and parameter
of the camera module which insert in the dome. The option
is useless(N/A)when the camera module does not have
this function.
5. 6 Video Output Setting
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
OFF
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
1. The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2. Operate joystick and move the cursor to【CAMERA SETTING】, press
【OPEN】, Enter the next main menu
3. Operate joystick and move the cursor to【VIDEO MODE】,press
【OPEN】, tilt up/down joystick Set the video output format Image input
format, Range:1080I/60,1080I/50,1080P/30,1080P/25,720P/60,
720P/50,
It will be valid after restart.
22
Camera setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
5. 7 Advance setting
1. The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2. Operate joystick and move the cursor to【CAMERA SETTING】 ,
press【OPEN】 , Enter the next main menu
3 . Operate joystick and move the cursor to 【ADVANCE SETTING】 ;
press 【OPEN】 to enter submenu, as left picture shows;
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
OFF
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
5. 7 . 1 DAY/NIGHT mode
1 . Operate joystick and move the cursor to【DAY/NIGHT】, press 【OPEN】,
tilt up/down joystick to choose AE mode, modes for choosing as follow:
● 【DAY/NIGHT】
● 【BLACK TIME】
● 【COLOR TIME】
● 【THRESHOLD】: sensitivity of switch between B/W and color.
The higher numerical value means lower sensitivity and longer switch
time. In contrast, the lower numerical value means higher sensitivity
and shorter switch time (Range: 8-28 dB)
● 【AGC LIMIT】Automatic gain selection range 8-28Db when the
darker【AGC LIMIT】value is smaller the image snow point is less
【AGC LIMIT】value is great the image snow point is more
ADVANCE SETTING
DAY/NIGHT
EXPOSURE
COLOR
PICTURE
FOCUS
BACK
EXIT
SETTING
2. Press 【OPEN】 to save.
OPERATION KNACKS
IR cut filter function uses color in day; use black and white at night.
This function not only guarantees the quality of image, but also saves the
room of storage.
DAY/NIGHT SETTING
DAY/NIGHT
BLACK TIME
COLOR TIME
THRESHOLD
AGC LIMIT
BACK
NEXT
AUTO
N/A
N/A
10dB
28dB
This function depends on the models and parameters of built-in camera
in dome, if the camera doesn't have this function, then it is invalid(N/A).
23
Camera Setting
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
OFF
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
ADVANCE SETTING
DAY/NIGHT
EXPOSURE
COLOR
PICTURE
FOCUS
BACK
EXIT
SETTING
1、Operate joystick, move the cursor to 【EXPOSURE】, press 【OPEN】,
tilt up/down joystick to choose AE mode, modes for choosing as follow:
● 【AUTO 】: default setting, auto Iris mode
● 【BRIGHT】: brightness priority mode
● 【IRIS】: iris priority mode
● 【SHUTTER】 : shutter priority mode
● 【MANUAL】 : override
2、Choose Iris priority mode 【IRIS】, press 【OPEN】to save.
3、Move joystick to the sub-choices of AE mode 【IRIS F1.4】, press
【OPEN】 to choose adequate Iris, press 【OPEN】 to save.
● 【 SHUTTER 1/50】it means shutter speed, when AE mode is shutter
priority, this function can be set.
● 【 IRIS
F1.4】 it means the size of iris, when AE mode is iris
priority, this function can be set.
● 【BRIGHT F2.0/ODB】it means brightness, when AE mode is brightness priority, this function can be set.
● 【EXPOS.COMP】 exposure compensation
5. 7 . 3 White balance mode
EXPOSURE
AE MODE
SHUTTER
IRIS
BRIGHT
EXPOS.COMP
5. 7 . 2 AE mode
AUTO
N/A
N/A
N/A
OFF
BACK
NEXT
1、Operate joystick, move the cursor to【WB MODE】 to choose white
balance mode, press 【OPEN】 to save.
Auto mode 【AUTO】 is the default mode of speed PTZ, which is autorevert real color after the white balance sensor check the environment by
camera. When choosing manual mode【MANUAL】, adjust the numerical
value of 【R GAIN】and【B GAIN】.
● 【R GAIN】t he range is 1-225; the numerical value is bigger, it means
that adding red is more, the tone changes to be warm.
● 【B GAIN】the range is 1-225; the numerical value is bigger, it means
that adding green is more, the tone changes to be cold.
Indoor mode 【INDOOR】, and the tone leans to cold.
Outdoor mode 【OUTDOOR】, and the tone leans to warm.
COLOR
WB MODE
R GAIN
B GAIN
COLOR GAIN
COLOR HUE
BACK
NEXT
24
AUTO
N/A
N/A
120
0
This function depends on the models and parameters of built-in
camera in dome, if the camera doesn't have this function, then it is
invalid(N/A).
Camera setting
CAMERA SETTING
ZOOM SPEED
HIGH
DIGITAL ZOOM
OFF
BLC MODE
OFF
SLOW SHUTTER
ON
WDR MODE
N/A
VIDEO MODE 1080I/60
ADVANCE SETTING
BACK
5. 7. 4 Image Setting Function
1. Operate the joystick to move the cursor to 【PICTURE】, move joystick
rightward or press 【OPEN】 to enter the submenu;
【GAMMA】gamma correction
【SHARPNESS】sharpness setting
【MIRROR】mirror image
【FLIP】180°image slip function
【HI-RESOLUTION】build-in hi-resolution function, depend on the type
of the camera module
【NOISE REDUCE】Image de noising
【IMAGE STABLE N/A】Image enhancement
ADVANCE SETTING
DAY/NIGHT
EXPOSURE
COLOR
PICTURE
FOCUS
BACK
EXIT
SETTING
5. 7. 5 Focus
PICTURE
GAMMA
SHARPNESS
MIRROR
FLIP
HI-RESOLUTION
NOISE REDUCT
IMAGE STABLE
BACK
NEXT
2. Press【OPEN 】to save the setting.
000
10
OFF
OFF
OFF
0
N/A
1. Operate the joystick to move the cursor to【FOCUS 】, move joystick
rightward or press【OPEN】to enter the submenu;
【AUTO FOCUS 】Setting the focus automatically or manually
【FOCUS OFFSET】Adjust the focus center, to eliminate the negative
effect on focus owing to the PMMA dome cover
2. Press【OPEN】to save the setting.
FOCUS
AUTO FOCUS
ON
FOCUS OFFSET 000
BACK
NEXT
25
Function setting
6. Function setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
6. 1 Preset
1 . The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds. Click each command to enter“preset menu”
according to the order of the left picture. As follows:
【PRESET NUMBER】
【SET PRESET】
● 【SHOW PRESET】
● 【CLEAR PRESET】
● 【AUTO TARCKING】(If the dome does not have this function, it won t display )
● 【EDIT PRESET LABEL】
●
●
Define preset and call preset function can be set by keyboard operation,
input preset number at first, then click the key“save /call preset”to carry out.
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO TRACKING
BACK
EXIT
2. Define current preset number: move the cursor to 【PRESET NUMBER】,
press 【OPEN】 to choose preset number, the range is 1-128 as the left picture
shows, here chooses number 5 as current preset, the following operations aim at
the current preset.
3. Define current preset: move the cursor to【SET PRESET】,press 【OPEN】,
by operating joystick to adjust magnification, to choose good objective image,
press【OPEN】 to save. If the image is very near, the Image is belong in digital
zoom. When setting preset, the image will jump to maximal optical zoom.
OPERATION KNACKS
Preset function is that dome stores current pan/tilt angle, zoom
and other position parameters into the memory. When necessary,dome
recalls these parameters and adjust camera to that position.
PRESETS
PRESET NUMBER
05
SET PRESET
SHOW PRESET
CLEAR PRESET
EDIT PRESET LABEL
BACK
EXIT
EDIT PRESET LABEL
LABEL:PRESET-05
BACK
EXIT
26
4. Display current preset: move the cursor to 【SHOW PRESET】, press
【OPEN】, the screen will display the current preset;
5 . Clear current preset: move the cursor to 【CLEAR PRESET】, press 【OPEN】,
the current preset is cleared.
6. Edit current preset label: move the cursor to【EDIT PRESET LABEL】,
press 【OPEN】 to enter into editing preset submenu, system auto-sets label
as PRESET-XX, press【OPEN】to revise label.
1.When running to program, display, clear preset and edit label,
should choose preset number at first.
2. The label may set up to 16 characters, and doesn't need editing
characters. Press【OPEN】 continuously to jump over and use
spacebar to replace the deleted characters. When you finish to
edit a character, press【OPEN】 to enter into the next editing
character; when you finish to edit the last character, pressing
【OPEN】to save. Press【CLOSE】 to exit. Character of label
is suitable for choosing as follow: 0-9, A-Z, :<>-. , space.
3. As the submenu【STATE】in【AUTO TRACKING】 is set as
OFF, it is valid to Call preset to set auto-tracking ON/OFF.
(Pls refer to the Paragraph 6.7)
Function setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO TRACKING
BACK
EXIT
SCAN
SCAN NUMBER
04
SCAN SPEED
50
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR SCAN
RUN SCAN
EDIT SCAN LABEL
BACK
EXIT
EDIT SCAN LABEL
LABEL:AUTO SCAN
BACK
EXIT
6. 2 Scan
Scan is that preset two points , then the camera repeatedly scan between the two points at a stable speed, the same magnification and pan. A dome has four scan tour.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds. click menu to enter “scan” menu, as the
left picture shows.
● 【SCAN NUMBER】
● 【SCAN SPEED 】
● 【SET LEFT LIMIT】
● 【SET RIGHT LIMIT】
● 【RUN SCAN】
● 【CLEAR SCAN】
● 【EDIT SCAN LABEL】
2、Define current scan number: operate joystick ,move the cursor to 【SCAN
NUMBER】,press 【OPEN】 ,tilt up/downjoystick to choose scan number,
press 【OPEN】to save .the following operations aim at the current scan
number.
3、Scan speed setting: operate joystick to 【SCAN SPEED】, press
【OPEN】, tilt up/down joystick to adjust scan speed, press 【OPEN】 to
save.
4、 Left limit setting: operate joystick to 【SET LEFT LIMIT】, press
【OPEN】, operate joystick to choose objective image, press【OPEN】 to
save. Right limit setting is the same as left limit setting
.
5、Edit scan label: operate joystick, move the cursor to 【EDIT SCAN
LABEL】, press 【OPEN】 to enter submenu“ edit label”, move the cursor to 【LABEL】, the system will auto-set the label as AUTO SCAN, press
【OPEN】 to revise.
The label can set up to 16 characters, and doesn't need editing
characters. Pressing 【OPEN】 continuously to jump over and using
spacebar to replace the deleted characters. When you finish to edit a
character, pressing 【OPEN】 to enter into the next editing character
when you finish to edit the last character, pressing 【OPEN】to save.
Press 【CLOSE】 to exit.
Character of label is suitable for choosing as follow: 0-9、A-Z、:
<>-. , Space. The editing ways of other labels are the same as above.
6、Run scan: operate joystick to 【RUN SCAN】, press 【OPEN】 to exit
the menu, and it starts to run scan.
1. left limit and right limit of scan can't be sent at the same point.
2.Under scan process, speed, magnification and tilt direction won't
change, if the speed, magnification and tilt direction of the two
limits are inconsistent, run scan is base on left limit.
27
Function setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
6. 3 Pattern
Pattern is built-in function in camera; the PTZ can record tracks while
less than 180s. (A series of pan/tilt controlling and lens controlling command).
A PTZ may set up to 4 pattern tours.
1. The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2 . Operate joystick, move the cursor to 【FUNCTION SETTING】, press
【OPEN】 to enter submenu.
3 . Operate joystick to 【PATTERN】, press 【OPEN】to enter menu
“Pattern”.
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO TRACKING
BACK
EXIT
● 【PATTERN NUMBER】
● 【PROGRAM PATTERN】
● 【RUN PATTERN】
● 【CLEAR PATTERN】
● 【EDIT PATTERN LABEL】
4 . Choose pattern number: move the cursor to 【PATTERN NUMBER 】,
press 【OPEN】, pattern you choose as current pattern, the following operations aim at the current pattern;
5 . Define current pattern tour: move the cursor to 【PROGRAM PATTERN】,
press 【OPEN】to set pattern track, move the image random, and draw the focus.
The PTZ has a tour that is no less than 180s, a series of park time, magnification,
focus will be recorded, press 【OPEN】 to save.
PATTERNS
PATTERN NUMBER
PROGRAM PATTERN
6 . Run pattern: operate joystick to 【RUN PATTERN】, press 【OPEN】
to run, the PTZ will continuously and repeatedly record the specific track.
RUN PATTERN
CLEAR PATTERN
EDIT PATTERN LABEL
BACK
EXIT
When carry out program, run, clear pattern and edit
label, should choose pattern number at first.
EDIT PATTERN LABEL
LABEL:PATTERN-1
BACK
EXIT
28
Function setting
6. 4 Tour
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
Tour is the built-in function in the PTZ, it will arrange the presets
into the queue of auto-tour, and can set how long it will park at preset.
Operate auto-tour is a process of incessantly transfer each preset. One
tour can store 32 presets at most.
1、 The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、 Operate joystick, move the cursor to 【FUNCTION SETTING】, press
【OPEN】enter submenu.
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO TRACKING
BACK
EXIT
3、Operate joystick, move the cursor to 【TOUR 】, press【OPEN】 to
enter menu “tour”;
4、Set the park time of preset: Operate joystick, move the cursor to
【TOUR DWELL】, press 【OPEN】, there will be a sign
in the front of
【TOUR DWELL】, the cursor jumps to right, tilt up/down to set park time,
and the range is 000-255(s)
5、 Set tour :move the cursor to 【EDIT TOUR】,press【OPEN】 to set
tour interface,【PO-S-TM】 set preset ,speed and time ,press 【OPEN】,
the first dwell is activated , tilt up/down joystick to choose preset number,
the preset numerical value should be within 1-80 preset , a tour can set up
to 24 presets .press【OPEN】,the cursor jump to the next dwell ,tilt up/
TOUR
TOUR NUMBER
EDIT TOUR
RUN TOUR
CLEAR TOUR
BACK
EXIT
down joystick to choose current arrival preset speed , total 8 level of
1
speed ,increasingly from level 1 to level 8;Press 【OPEN】,the cursor
jumps to the next dwell , tilt up/down joystick to set current preset
maintaining time,60 seconds maximum . If set the presets of the second
line ,move the cursor to the second line , press 【OPEN】 to continue
edit .press 【OPEN】 to save after setting ,press 【CLOSE】 to exit.
6、 Run tour: Operate joystick, move the cursor to 【RUN TOUR】, press
【OPEN】 to exit the menu, it starts to run tour.
EDIT TOUR
PO-S-TM PO-S-TM PO-S-TM
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
the system will leap over the preset automatically when the
stay time of one item setting up on 0; The PTZ will not run
the tour of latter preset when preset or movement speed
setting up on 0 .
BACK
EXIT
29
Function setting
6. 5 Zone
MAIN MENU
A PTZ may be set up to 8 zones; the regional scene can't be overlapped.
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
User can set label for each zone. When setting【ZONE LABEL】 as ON,
the PTZ will display zone label as it runs some zone. It is convenient to
know the zone that the camera shoots by setting zone label.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate the joystick, move the cursor to 【FUNCTION SETTING】, press
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO TRACKING
BACK
EXIT
【OPEN】to enter submenu.
3、Operate the joystick, move the cursor to 【ZONES】, press 【OPEN】 to
enter submenu, as the left picture shows.
●
【ZONES NUMBER】
●
【SET LEFT LIMIT】
●
【SET RIGHT LIMIT】
●
【CLEAR ZONE】
●
【EDIT ZONE LABEL】
Regard the left/right limit as the demarcation line, and set the middle
part as a zone. Various operational ways are the same as other settings in the
menu. Therefore we won't explain it again.
ZONES
ZONES NUMBER
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR ZONE
EDIT ZONE LABEL
BACK
EXIT
EDIT ZONE LABEL
LABEL:ZONE-1
BACK
EXIT
30
1
Function setting
MAIN MENU
6 . 6 Time running
User can set the time of preset, scan, tour and pattern.
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
1.Call 95 preset or call 9 preset twice within 3 seconds to enter into the main
menu.
2. Operate the joystick, move the cursor to 【FUNCTION SETTING】 , press
【OPEN】 to call the submenu.
3. Operate the joystick, move the cursor to 【TIME RUNNING】 , press
【OPEN】 to enter into the menu setting. Please refer to the left picture.
【DAY】 set the date
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO TRACKING
BACK
EXIT
TIME RUNNING
DAY
SAT
TIME CHANNEL
1
START TIME
00:00
END TIME
00:00
RUNNING
TOUR1
BACK
EXIT
【TIME CHANNEL】 4 channels can be set.
【START TIME】 Set the start time
【END TIME】 Set the end time
【RUNNING】 User can set the preset , scan , tour,
pattern to every channel.(1-4)
4. This channel will not conflict with other channels when you set
【RUNNING】 as close.
1.When user do the action of scan, tour or pattern, if time is over,
then the PTZ will execute park action, the user's action will
stop. After the time, the PTZ will resume the action and preset
which is set before the park time. (Before the park time, if the
PTZ is on some preset, the PTZ will resume the preset, if PTZs
execute the action of scanning, tour or pattern, the PTZ will resume
original action. If users handle some action with keyboard, PTZ
will also resume the action which users are going on with keyboard.)
2. During the timing period of movement function, it is not allowed
operate the PTZ manually. When users handle the PTZ, the timing
movement function will interrupt. If there is no any action during
30 seconds, it will be in the state of timing function, and return
to the timing movement function. Or if there is idle function,
it will be do the action of idle time function.
3. Timing function will close while user setting presets, right and
left limit, menu status, recording scan and setting any other function.
4.When the PTZ execute alarm, timing, idle function, the priority for
alarm is the highest, for timing is the second, for idle is the lowest.
31
Privacy zone masking
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
WINDOW BLANKING
WINDOW NUMBER 01
EDIT WINDOW
ENABLE WINDOW OFF
CLEAR WINDOW
BACK
EXIT
Privacy zone masking
7. Privacy zone masking
Privacy function can show someone piece of regional shielding while
protecting. For example, protect the window of bedroom or ATM of bank. A
PTZ can set up to 24 privacy windows.(Masking setting function is relative with the model of camera module. The masking numbers will be different according to the different cameras.)
Hitachi Camera: It can be set 8 masking at most in 360°surveillance
range,can set 2 masking at most per screen. The screen will note" please
move" when the position can not be set. It can not set masking when the
PTZ rotates down ≥45°.
Sony Camera: It can be set 24 masking at most in 360°surveillance range.
( Sony 45 series can be set 8 masking at most ). It can not set masking
when the PTZ rotates down ≥20°.LG,CNB Camera module have no
masking function.
1、The system enters into the main menu by calling 95 preset or by calling
9 preset twice within 3 seconds.
2、Operate the joystick to 【WINDOW BLANKING】, press 【OPEN】to enter menu“ window blanking”.
● 【WINDOW NUMBER】choose window number as current privacy window, other choices in the menu just aim at current privacy window;
● 【EDIT WINDOW】program current window;
● 【ENABLE WINDOW】 permit/prohibit current privacy window,
there are two choices: ON---permit current privacy window/OFF---prohibit
current privacy window
● 【CLEAR WINDOW】clear current privacy window, after clearing
it, the window will auto- change as OFF.
3、Program current privacy window: Firstly choose window number, then
do the following operations:
a. Operate the joystick, move the cursor to 【EDIT WINDOW】, press【OPEN】 to move the image that need privacy window to display in the screen.
b . Press【OPEN】, there will be a square displaying in the center of the screen, operate the joystick, and move the square to the central place that need
to conceal.
c. Press【OPEN】, operate the joystick to adjust the size of privacy zone:
joystick to up, the height is increased; joystick to down, the height is reduced; joystick to right, the width is increased; joystick to left, the width is
reduced.
d. Press 【OPEN】 to save the current privacy zone setting, and the window
will auto-change as ON at the same time.
This function is decide by the parameter of built-in camera,
if the camera has not this function, this option is invalid. (N/A)
32
Alarm Function
8. Alarm function
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
ALARMS
RESUME
OFF
SEQUENCE
002
RESET DELAY
020
ALARM CONTACT N/C
ALARM SETTING
ARM SETTING
BACK
EXIT
ALARM SETTING
NUMBER
01
ACTION
TOUR
ACTIVATE AUX
NONE
PRIORITY
HIGH
BACK
Speed dome may connect with 4 alarm input, 1 alarm output, and support
alarm linkage. The external alarm message sends to the dome, then the dome
sends to alarm point shoot (to call preset, auto scan, auto cruise and auto pattern),
and choose that to run alarm output or not.
1 . The system enters into the main menu by calling 95 preset or by calling 9
preset twice within 3 seconds. Click each menu according to the left picture, then
enter menu alarm, choices as follow:
● 【RESUME】resume mode after relieving alarm input, there are two
choices: ON---clear alarm output, the dome will stop.
OFF---just clear alarm output.
● 【RESET DELAY】set alarm reset and delay the time (1-225s), how
long to relieve and run 【RESUME】 after the dome receives alarm message.
● 【ALARM CONTACT 】set state of the relay. N/C---often close the state,
N/O---often hold the state. If setting as often closing the state, the relay is
in closing the state when there is no alarm to output; when there is alarm to
output, the relay is in holding the state.
● 【AL ARM SETTING】
● 【ARM SETTING】
2 . Operate joystick and move the cursor to【ALARM SETTING】, press【OPEN】
to enter the menu alarm setting
● 【ALARM NUMBER】alarm number is corresponding with 12 bits plug in
the external switching board of the dome(as below shows). 001 priority is
the highest, 004 priority is the lowest. The two lines alarm input at the same
time, the dome run alarm that the highest priority.
● 【ALARM ACTION】as current alarm input, to run the action. Choices for
choosing as follow. NONE---none action/SCAN/PAT X---run a pattern tour
/TOUR---run tour/PRESET---call preset, when the dome number is set as 1,
to call preset 1; when the dome number is set as 2, to call preset2.
● 【ACTIVATE AUX】as current alarm input, to run alarm output or not.
NONE---none alarm output/AUX 1---the first alarm output/AUX 1---the
secondary alarm output/BOTH--- two alarms output.
● 【ALARM PRIORITY】 alarm priority can be defined as three grades:
high, middle, low.
EXIT
33
Alarm Function
8.1 ARM Setting
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
1. Call 95 preset or call 9 preset twice within 3 seconds and then input the
password to enter the main menu.
2. Operate the joystick up and down, move the cursor to 【ALARMS 】 ,
press【OPEN】 to call the submenu.
3. Operate the joystick up and down, move the cursor to 【ARM SETTING】 ,
press 【OPEN 】to call the submenu. Please refer to the left picture.
4. Operate the joystick up and down, move the cursor to 【DAY】, Press
【OPEN 】to choose it , Operate the joystick up and down to set date, set
ALARMS
RESUME
the date according to the week. To set the Alarm state and Alarm date based
OFF
SEQUENCE
002
RESET DELAY
020
ALARM CONTACT N/C
ALARM SETTING
● 【ARM TIME】 : User can set the alarm time.
● 【EXIT】: Exit the menu.
EXIT
ALARM SETTING
NUMBER
01
ACTION
TOUR
ACTIVATE AUX
NONE
PRIORITY
HIGH
34
under Alarm off. Alarm Setting is effective under Alarm on)
● 【BACK 】: back to the former menu.
BACK
EXIT
● 【ARM STATE】 Alarm off /Alarm on (Alarm Setting is noneffective
● 【UNARM TIME】: User can set the alarm off time.
ARM SETTING
BACK
on the time.
Appendix
9. Appendix
MAIN MENU
SYSTEM SETTING
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARMS
EXIT
9. 1 Menu Index
SYSTEM SETTING
CAMERA SETTING
EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
COMM SETTING
BACK
EXIT
ZOOM SPEED
DIGITAL ZOOM
BLC MODE
SLOW SHUTTER
WDR MODE
ADVANCE SETTING
BACK
HIGH
OFF
OFF
OFF
N/A
L:SPEED DOME
BACK
EXIT
DAY/NI GHT SETTING
INITIAL INFO
DAY/NIGHT
AUTO
BLACK TIME
N/A
C O LOR TIME N/A
THRESHOLO
10DB
AGC.LIMIT
2 8DB
EXIT
FIRMWARE
V1.10
PROTOCOL:PELCO
DOME ADDRESS:001
COMM:2400,N,8,1
BACK
EXIT
EXPOSURE
DISPLAY SETUP
DOME LABEL
PRESET LABEL
ZOOM LABEL
ZONE LABEL
DIR. LABEL
TEM. LABEL
TIME LABEL
DATE LABEL
BACK
OFF
OFF
ON
OFF
ON
OFF
ON
ON
AE MODE
SHU TTER
IRIS
BRIGHT
EX POS .C ONP
BACK
EX IT
AU TO
N /A
N/A
N/A
4.5DB
OFF
OFF
002
020
N/C
EDIT PRESET LABEL
SCAN
A UTO
N /A
N /A
110
0
L:PRESET 05
BACK
EXIT
EDIT SCAN LABEL
SCAN NUMBER 04
SCAN SPEED
50
SET LEFT LIMIT
SET RIGHT LIMIT
RUN SCAN
CLEAR SCAN
EDIT SCAN LABEL
BACK
EXIT
L:AUTO SCAN
BACK
EXIT
ALARM NUMBER
ALARM ACTION
ACTIVATE AUX
ALARM PRIORITY
BACK
EXIT
001
TOUR
NONE
HIGH
ARM SETTING
DAY
ARM STATE
ARM TIME
UNARM TIME
BACK
EXIT
SUN
OFF
N/A
N/A
EDIT PATTERN LABEL
PATTERN NUMBER
PROGRAM PATTERN
RUN PATTERN
CLEAR PATTERN
EDIT PATTERN LABEL
BACK
EXIT
L :PATTERN 1
BACK
EXIT
EDIT TOUR
ON
ON
005
SCAN
AUTO
045C
CENT
CLEAR
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
CLEAR ALL WINDOWS
FACTORY DEFAULTS
RESTART
BACK
EXIT
PASSWORD SETUP
OFF
PI CTURE
GA MM A
SHA RPNES S
MIR RO R
FIlP
HI -RES OLUTIO N
NO ISE R ED UC T
IM A GE STA BL E
BA CK
EXIT
110
10
O FF
ON
O FF
0
N/A
03:20:18
07/10/10
WED
PO-S-TM PO-S-TM PO-S-TM
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
00-0-00 00-0-00 00-0-00
TOUR
TOUR NUMBER
EDIT TOUR
RUN TOUR
CLEAR TOUR
BACK
EXIT
1
BACK
EXIT
FOCUS
AU TO FO CU S
ON
FOC US O FFS ET 000
BA CK
EXIA
ADVANCE SETTING
EIS ENABLED
N/A
PRESET FREEZE
N/A
AUTO FOCUS
O FF
DEFOGGE R
10
A D J SPEED
100
IR HEADLIGHT
SPECIAL SETTING
BACK
EXIT
IR HEADLIGHT
CLOCK SETTING
TIME
DATE
DAY
EXIT
01
ALARM SETTING
PRESETS
PRESET NUMBER 05
SET PRESET
SHOW PRESET
CLEAR PRESET
AUTO TARCKING NONE
EDIT PRESET LABEL
BACK
EXIT
PATTERNS
COLOR
WB M ODE
R G AI N
B G AI N
CO LO R GAIN
CO LO R H UE
BA CK
EX IT
MOTION
OLD :******
NEW :******
CONF :******
ENABLE :
BACK
EXIT
WINDOW NUMBER
EDIT WINDOW
ENABLE WINDOW
CLEAR WINDOW
BACK
EXIT
ALARMS
RESUME
SEQUENCE
RESET DELAY
ALARM CONTACT
ALARM SETTING
ARM SETTING
BACK
EXIT
ADVANCE SETTING
DAY/NIGHT SETTI NG
EXPOSURE
C OLOR
PICTURE
FOCUS
B ACK
EXIT
EDIT DOME LABEL
AUTO FLIP
PROPORTION
PARK TIME
PARK ACTION
BOOF ACTION
FAN ENABLED
TEMP C/F
ADVANCE SETTING
BACK
WINDOW BLANKING
FUNCTION SETTING
PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
BACK
EXIT
MODE
DELAY TI ME
BW
ACT. AUX1
LED 1
LED 2
LED 3
LIGHT
B ACK
EXIT
MID
00 2
AUTO
OFF
10 0
20 0
×
×
EDIT ZONE LABEL
ZONES
ZONES NUMBER
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR ZONE
EDIT ZONE LABEL
BACK
EXIT
1
L:ZONE 1
BACK
EXIT
TIME RUNNING
DAY
TIME CHANNEL
START TIME
END TIME
RUNNING
BACK
EXIT
SAT
1
00:00
00:00
TOUR1
COMM SETTING
S/N:4JKAA7824000058
CONF:4JKAAA7824000058
SITE ID
001
COMM SPEED 2400BPS
PROTOCOL:TACTORY
EXIT
SPECIAL SETTING
GRID
POS.M ODE
ZERO AZI
B ACK
EXIT
ON
MODE1
35
Appendix
9.2 Rs485 Bus Basic Knowledge
Ø Characteristics of Rs485 Bus
Ø The connection of 120Ω termination resistor:
As specified by Rs485 standard, Rs485 Bus is
of half-duplexed data transmission cables with
characteristic impedance as 120Ω. The maximum
load capacity is 32 unit loads (including main
controller and controlled equipment.)
Connection mode for 120 Ω resistance of equipment
terminal. Setting connection of terminal resistance
120 Ω in the base cover. (Refer to Picture 9.2-3):
Default of factory (No.8 digit of SW2 is set “OFF”
on code switch)No.8 digit of SW2 is set “ON” on
code switch if needed to connect 120 resistance.
Ø Transmission distances of Rs485 Bus
When user selects the 0.56mm(24AWG)twisted
pair wires as data transmission cable, the maximum
theoretical transmitting distance are as follows:
Baud rate
Max distance
2400BPS
1800m
4800BPS
1200m
9600BPS
800m
19200BPS
600m
R6
If user selects thinner cables, or installs the PTZ
in an environment with strong electromagnetic
interference, or connects lots of equipment to the
Rs485 Bus, the maximum transmitting distance
will be decreased. To increase the maximum
transmitting distance, do the contrary.
Ø Connection and termination resistor
The Rs485 standards require a daisy-chain Connection
between the equipment. There must be termination
resistors with 120Ω (as the picture 9.2-1).
Please refer to picture 9.2-2 for simple connection.
“D”should not exceed 7m.
120Ω
1#
120Ω
2#
3#
4#
32#
Picture 9.2-1
A+
B-
D
A+
B-
2#
3#
120Ω
1#
120Ω
4#
32#
Picture 9.2-2
36
Picture 9.2-3
Appendix
Ø Problems in practical connections
In some circumstances user adopts a star
In such circumstances the factory recommends
the usage of RS485 distributor. The distributor can
configuration in practical connection. The
change the star configuration connection to the mode
termination resistors must be connected to the
of connection stipulated in the RS485 standards.
two equipment 1# and 5# in Picture 9.2-4. As the
The new connection achieves reliable data transmission.
star configuration is not in conformity with the
(Refer to Picture 9.2-5).
requirements of RS485 standards, problems
such as signal reflections, lower anti-interference
performance arise when the cables are long in the
Rs485 Distributor
A+
connection. The reliability of control signals is
decreased with the phenomena that the PTZ does
B-
120Ω
1#
120Ω
2#
120Ω
3#
not respond to or just responds at intervals to the
controller, or does continuous operation without
stop.
120Ω
1#
Picture9.2-5
6#
Main controller
32#
120Ω
15#
Picture 9.2-4
Ø Rs485 Bus troubleshooting
Trouble
PTZ can do
self-testing
but cannot be
controlled
The PTZ can be
controlled but
the operation is
not smooth.
Possible cause
Solution
A、The address and baud rate setting of PTZ
are not in conformity with those of controller.
B、The "+" and "-"connection of Rs485 Bus is
incorrect.
C、The PTZ is very far away from controller.
D、There are too many PTZs connected in the
System.
A、Change the address and baud rate of controller or PTZ
B、Replace Rs485 Bus wires
C、Make sure the connections are fully seated
A、The Rs485 Bus line is not in good
contact with the connectors.
B、One wire of the Rs485 Bus is
broken.
C、The PTZ is very far from
controller.
D、There are too many PTZ
connected in the system.
A、Secure the connection;
B、Replace Rs485 Bus Wires
C、Add termination resistors to the system
D、Install Rs485 distributor
37
Warnings
10. Installation
10. 1 Caution
l Please refer to user manual before installation.
l Power: AC 24V, for actual needs, please refer to label of product.
l Precise optical and electronic parts inside of product. Avoiding severe press, hard vibration etc non-correct
operation methods, which may cause damage to product when transportation and installation.
l Please do not disassemble parts inside of product at random, which may cause negative influence on use
of product. No additional parts available.
l Please comply with standards of Electrify Safety and use our own power transformer of product. Enough
distance must be ensured between RS-485 cable, Video signal cable and equipments of high voltage when
transmission. Thunder-proof, surge-proof and wave-proof , etc protection measures are needed.
l Do not use product beyond the rated temperature, humidity or specifications of power. Do not place camera
point to Sun or shining objects.
l Do not use cleansers with abrasion to clean product. Please use dry cloth to clean up dirt; Neutral cleanser
is needed when not easy to clean.
l Handle product with care so as to avoid crash or vibration; Damage is caused when incorrect usage.
l Please fix product to the position which is solid and firm.
l Please use special paper of lens to clean up dirt on Lens.
10. 2 Distributing the Line in Security
Please refer to right picture 11.1-1
= It is necessary to keep 50 meters distances at least bet-
Power cable lightning rob
Communication cable lightning rob
Video cable lightning rob
ween the high voltage unit and the high voltage cable with
signal transmission line.
O
45
The PTZ must be installed
within the angle of 45 degrees
under lightning rob
= Outdoor wiring is best to along under the eave of the
house.
= Wiring at void place must adopt by way of sealed steel
tube bury underground, and sealed steel tube should be
grounded by one Bus. It is absolutely forbidden to adopt
wiring without holder.
Ground resistance should
be lower than 4Ω
Sealed steel tube
= Under thunderstorm or high inductive voltage region
(e.g.: high voltage transformer substation),
you must add extra high power lightning proof equipment
and install lighting rob.
Picture 10.2-1
= Outdoor equipment, routes of lighting proof and ground design must consider according to the request of construction
lightning proof, and coincide with connection requests of country and industry standard.
●The system must equipotential ground. Grounding equipment must satisfy the anti-jamming and electrical safety requirements and must not short circuited or mix connection with high voltage electricity net. When the system is grounded
separately, the ground resistance should be not more than 4 Ωand section of the grounding conducting wire should be less than
2
25 mm .
38
Warnings
10. 3 Lightning Proof and Surge Proof
This product uses TVS lightning Proof technology,
can prevent from the damage of the equipment caused by
kinds of pulse signal such as instant lightning strike of
power below 4000V, the surge and so on.
At the same time, you must adopt the essential protective
measure according to the actual situation regarding outdoor
installation under the guarantee electricity security.
(Refer to chapter 1.3 Distributing the line in security)
10. 4 Water Proof
Outdoor PTZ has well waterproof /moisture-proof /dust
proof performance, has achieved the IP66 international
standard. The indoor PTZ doesn't allowed to install in outdoor
environment which is full of moisture and possibly en ter water.
You should prevent the product and the internal components
from damage that caused by the long time waterdrop or spatter.
10. 5 The preparation of installation
Ø The request of the quality of installation
person and maintained:
● All installation and maintenance work related this
product should complete by technical personnel who
have qualification of installation and maintenance.
Ø Basic requirements
● Please refer to this handbook for detail.
Ø Stuff Preparation
Please select the type of cables based on transmitting distance:
●Minimum video coaxial cable requirements:
1)75Ωimpedance
2)All copper conductor wire
3)95% copper net structure
Domestic Gauge
RG59/U
International Gauge
Maximum Distance(ft/m)
RG59/U
750ft(229m)
5C-2V
RG6/U
1,000ft(305m)
7C-2V
RG11/U
1,500ft(457m)
●RS485 Communication cables (Refer to manual appendix)
●24VAC Power supply cable (Refer to manual appendix)
Ø Keep All the Original Package Materials
Please preserve the mode original package material
properly after opening the PTZ packing, in order to
mail the PTZ that is wrapped with original package
material to the agent or return it to the factory to repair
if problem occur.
It is likely to bring on the damage that caused by the
transport accident on the way if the mode uses the
non-original package material, and extra cost may
arise accordingly.
Ø Brief introduction of mounting way
● All electrical work must be observe local latest
electricity laws, regulation on fireproof as well as
the related laws and regulations:
● Checking everything is completed according to
packing list. Make sure the application place and
the way of installation for PTZ is coincide with
Mounting way of pan/tilt: wall mount, pendant mount.
the request. If not, please contact your supplier.
● Please use this product according to the working
conditions request.
● Please handle with the pan/tilt module carefully, do
not extrude various structure parts; The down cover
belongs to the senior optics part, do not touch with hand;
Please do not get through power except for the electrifying
Bracket Installation Installation position must
enable to undertake high weight pressure,
which must be 4times of the total weight of PTZ
and bracket.
The wall must be strong and stable, bracket must
be ensure to install on the real wall but not the
surface coating of the wall.
inspection in process of installation.
Ø Check the structure intensity for installation
space and installation site.
● Make sure you have enough space to hold this product
and it's parts of installation in the site.
● Make sure the bearing capacity of ceiling, wall,
bracket that installs the PTZ support the gross weight
of the PTZ and the structural parts of installation.
It is necessary to have the safe coefficient of 4 times
or above.
39
Installation Introduction
11. Installation instruction
● Structure Introduction
The Dome utilizes overall packing, and mainly consists of four parts, connection board cover,
Main body cover, Main body , and IR LED lamp cover.
Wall bracket
Pendant bracket
Bracket connection plate
Connection plate cover
Main body cover
Main body
IR LED lamp cover
● Basic Size graph
84
255
178
100
178
40
Installation Introduction
11.1 Wall mount installation
11. 1. 1 wall bracket installation
Integrated the DOME and the wall bracket together with
3pcs M4*12 screws contained in the accessory bag, and
make sure the cable is completely embedded in the outlet
slot. Use M8 screw to fix the dome on the wall.
Please refer to figure 11.1.1-2
1. The installation site must be able to support
the sum of weight such as the dome、 the bracket
and the pedestal four times.
2 . The chosen wall of installation site must be
solid and have no delaminated phenomenon,
must make sure the bracket installs on the wall
but not in the superficial slipcover.
On the installation wall, use wall bracket as a templet
to mark the center position of the hole (as picture 11.1.1-1
shows).
203
Picture 11.1.1-2
Please see NO.① in the picture, smear the sealed glue
on the brim of the bracket and the dome will be prevented
the water entering. (as picture11.1.1-3):
(1) All sides interface between wall mount bracket
and the wall.
73
110
84
Outdoor wall
mount bracket
Outdoor dome
Picture 11.1.1-1
Picture 11.1.1-3
User use the electric drill to drill four M8 holes on the
installation surface. The length is around 75mm and then
install M8*70 screw. (as picture 11.1.1-2 shows).
The user must install the outdoor bracket
according to below requirement strictly.
It does not belong to our maintenance
scope if the dome was damaged causing
by disobey the requirement to install.
41
Installation Introduction
11.2 Pendant mount installation
11. 2. 1 Pendant bracket installation
1. The installation site must be able to support
the sum of weight such as the dome、the bracket
and the pedestal four times.
2 . The chosen wall of installation site must be
solid and have no delaminated phenomenon,
must make sure the bracket installs on the wall
but not in the superficial slipcover.
Integrated the DOME and the pendant bracket together with
3pcs M4*12 screws contained in the accessory bag, and make
sure the cable is completely embedded in the outlet slot. Use
M8 screw to fix the dome on the wall.
Please refer to figure 11.2.1-3
On the installation wall, use pendant bracket as a templet
to mark the center position of the hole (as picture 11.2.1-1)
shows).
Picture11.2.1-3
Picture 11.2.1-1
The user must install the outdoor bracket
according to below requirement strictly.
It does not belong to our maintenance
scope if the dome was damaged causing
by disobey the requirement to install.
User use the electric drill to drill three M8 holes on the
installation surface. The length is around 75mm and then
install M8*70 screw. (as picture 11.2.1-2 shows)
Connect the power cable, video cable and Rs485 cable
together as figure 11.2.1-4
1
2
3
4
Red
Black
Picture 11.2.1-3
1. Video connector
2. Alarm terminal 1
3. RS485 terminal
4. Power supply terminal
Picture 11.2.1-4
42
Installation Introduction
11.3 installation instruction
11. 4 Electrification inspection
Use 3pcs screws to integrate the dome and the bracket
connection plate together by turning them 10 degree
clockwise, as shown in the below figure:
Connect video cable and control cable to the other equipments;
Electrify DC12V power.
The PTZ carries on self-checking and executes replacement
procedure after power-on.
In the process of self-checking, camera will rotate horizontally
and slowly for one and half cycle to the default original horizontal
point which is set by factory, then upwardly turn to original vertical
point, then downwardly to original horizontal point. Lens will be
pulled from far focus to near focus to complete self-checking.
The whole camera is absolutely steady means PTZ completed
self-checking and ready to be controlled.
If unstable, please refer to the troubleshooting in the operation
manual appendix.
Picture 1 1.3-1
Integrate the bracket connection plate and the dome
together with the M3*8 screws contained in the accessory
bag, as show in the below figure:
Picture 11.3-2
43
Maintenance
12.Maintenance service terms
1. Range of warranty
●
The product will be maintained free for one year.
●
The product will be obtained the free maintenance service if the same malfunction appears again within three
months.
●
Malfunction of products caused by force majeure (such as war, earthquake, lightning strike and so on ), abuse,
non-standard operation, change of construction, non-normal wear or accident are non-free of warranty.
●
Please prevent from the damage which is caused by heavy pressure , the fierce vibration and soaks in the
process of transportation and storage, which does not belong to the free maintenance scope.
●
Please adopt the way of fission package or original package to transport because the product damage dose
not belong to the free maintenance scope if you use the whole packing way , not the original packing way.
●
The maintenance services will not be free when the pan/tilt module is disassembled or serviced by the user
voluntarily.
●
Our company implements the lifetime payable service if the product in malfunction has surpassed the
warranty period.
●
To the products with defect :if it's in the period of warranty, please fill in the form of warranty information
correctly, describe the trouble in details, and provide original sales. invoice or its copy.
●
For the damage and loss which was caused by the user's specifically application, factory won't bear any risk
and responsibility. The factory compensation made by breach of faith, negligence or tortious won't exceed the
amount of the products. The factory won't bear any responsibility for the special, unexpected and continue
damage caused by any other reasons.
●
Our company has the final right of explanation for the above terms.
2. Warranty terms
●
If the products are within the warranty time, the buyer should fill in the warranty card and send back together
with the products.
3. Shipping
●
If the product needs repaired , you can return it to the manufacturer through the supplier or directly. If you
choose the later , please contact us in order to speed up the process. And our company only undertake the
one-way freight from manufacturer to customer after maintenance.
44
HD-SDI Infrared Mini high speed dome
Operation and installation user manual
Version V1.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement