Datasheet - Mouser Electronics
Protek Test and Measurement
45 Smith Street
Englewood, NJ 07631
TEL: 201-818-7711
FAX: 201-760-9888
www.protektest.com
Excellence in Peformance and Value
Table of Contents
Selection Guide
Oscilloscopes
1
Analog Oscilloscopes
Hand-Held DSOs
Power Supplies
Power Supplies
Single Output Analog Readout
Single Output Digital Readout
Dual Output Digital Readout
Triple Output Digital Readout
LCD Digital Displays
Programmables
Electronic Load
Multimeters
Loop Calibrator
Bench
Hand-Held
Clamp-On
6020
6030C
820 / 840 / 860
S2401
S2405
2
3
4/5
6
7
303 / 310
1805 / 3003B
3005B / 3006B
3015B / 3032B
3033B / 3040T
3030 / 3030D / 3030T
P6000
L300
8
9
10
11
12
13
14 / 15
16 / 17
30C
B940
B4100
B845
6800
6500
304 / 305 / A480B
18
19
20
21
22
23
24
Generators
Sweep Function
B8011
B8400
B8110 / B1990
B821
25
26
27
28
Counters
Universal
C3100
B3110
B8118
29
30
31
Component Testers
LCR Meter
Z9218
Z8200
CM109 / CM110
CL200
32 / 33
34
35
35
AM/FM Signal Generator
3201
3290
B1240
36 / 37
38 / 39
40 / 41
Audio Products
Insulation Tester
SL100 / B850
DI2001 / DI4000
42
43
Hand-Held Capacitance Meter
Hand-Held LC Meter
RF Instruments
Special Purpose
Instruments
Signal Strength Analyzer
Accessories
Copyright © Protek Test & Measurement
44
Protek Test and Measurement
45 Smith Street, Englewood, NJ 07631
Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com
Email:
[email protected]
Selection Guide
Multimeter Selection Guide
Bench Type
Function Generator Selection Guide
Hand-Held Type
Model
B4100
B940
B845
6500
6800
Model
B8011
B8400
B8110
B821
No counts
200,000
4,000
20,000
50,000
80,000
Freq. Range
0.02Hz-2MHz
0.004Hz-4MHz
0.01Hz-10MHz
0.2Hz-20MHz
No Digits
5 1/2
3 3/4
4 1/2
4 4/5
4 7/8
Counter
Yes
*
Sine
Yes
Yes
Yes
Yes
*
Square
Yes
Yes
Yes
Yes
Triangle/Ramp
Yes
Yes
Yes
Yes
Yes
Dual Display
Analog Bar graph
*
Trend plot display
*
Back light
*
*
DCV accuracy
±0.05%
±0.3%
True RMS
*
*
*
*
±0.05%
*
*
Pulse
±0.03%
±0.05%
Burst
Yes
Yes
Gate/Trigger
*
Yes
Yes
Yes
Yes
Yes
Yes
AC +DC Meas.
*
*
Lin Sweep
DB
*
*
Log Sweep
*
*
*
TTL Out
Yes
Yes
Yes
*
*
*
Ext. VCF Input
Yes
Yes
Yes
*
Sweep
Yes
Yes
*
Start/Stop
*
Sweep Out
Yes
Yes
Capacitance
Frequency
*
Pulse width
Duty Cycle
*
Temperature
*
Continuity buzzer
*
*
*
*
*
Diode Test
*
*
*
*
*
Pulse Generator
Yes
Yes
Yes
*
±Peak Hold
*
Compare (go/no-go)
*
Min/Max/Avg
*
*
*
*
Relative mode
*
*
*
*
Memory Sto/RCL
*
GPIB interface
Optional
RS232 Interface
*
*
*
*
Comments
Selectable count
Delay hold
*
Auto hold
Resolution
Approvals
CE
CAT II
CAT III
CAT II
600V CE
1000V CE
1000V CE
CAT III
600V CE
Power Supply Selection Guide
Triple Output
Double Output
Model
3033B
3040T
3030T
3030D
3032B
3015B
Volts
0 to ±30V (2), 5V Fixed
0 to ±36V (2), 3.3/5.0V Fixed
0 to ±30V (2), 5V Fixed
0 to ±30V (2)
0 to ±30V (2)
0 to ±30V (2)
Amps
0 to 1.5A, 5A Fixed
0 to 2.5A, 0 to 5.0A Fixed
0 to 3.0A, 0 to 3.0A Fixed
0 to 3.0A
0 to 3.0A
0 to 1.5A
Display
2 LED
2 LED
2 LCD
2 LCD
2 LED
2 LED
Series/Parallel
Series
Both
Both
Both
N/A
N/A
AC Input Volts
120V / 220V
120V / 220V
120V / 220V
120V / 220V
120V / 220V
120V / 220V
Power Consumption
192VA
455VA
310VA
305VA
300VA
150VA
Size H x W x D (in)
6 x 9 x 13
6 x 9 x 13
8 x 11 x 13
8 x 11 x 13
6 x 9 x 13
6 x 9 x 13
Weight (lbs)
20
17
23
22
20
17
Model
3005B
3003B
3006B
1805
3030
310
303
P6000
Volts
0 to ±30V
0 to ±30V
0 to ±60V
0 to ±18V
0 to ±30V
0 to ±30V
0 to ±30V
0 to ±36V
Amps
0 to 5.0A
0 to 3.0A
0 to 1.5A
0 to 5.0A
0 to 3.0A
0 to 10A
0 to 3.0A
0 to 3.0A
Display
2 LED
2 LED
2 LED
2 LED
1 LCD
Analog
Analog
1 LCD
AC Input Volts
120V / 220V
120V / 220V
120V / 220V
120V / 220V
120V
120V / 220V
120V / 220V
110V / 220V
Power Consumption
133VA
190VA
190VA
170VA
160VA
520VA
190VA
200VA
Size H x W x D (in)
6 x 5 x 13
6 x 5 x 13
6 x 5 x 13
6 x 5 x 13
8 x 5 x 11
5 x 6 x 13
5 x 6 x 13
4 x 8 x 10
Weight (lbs)
15
15
15
15
11
26
14
13
Single Output
Programmable
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
1
6020
20MHz Dual Trace Oscilloscope
with Alt-Mag
K 20MHz Bandwidth
K Alt-Mag sweep for simultaneous display of main and X10 magnified trace
K Alternate trigger for a stable display of unrelated signals
K X10 Horizontal Magnification
K P-P auto trigger
K High brightness CRT with internal graticule
K Z-axis modulation
K Light weight with low power consumption
CE
6020
SPECIFICATIONS
Vertical Amplifier
(CH 1 and CH 2)
Sensitivity: 5mV/Div to 5V/Div in 10 steps (1-2-5 seq)
Accuracy: ±3%
Bandwidth (-3dB): DC: 0Hz to 20MHz, AC: 10Hz to 20MHz
Rise Time: < 17.5ns
Input Impedance: Res: 1MΩ ±5%, Cap: 25pF ±5pF
Input Coupling: AC, DC, GND
Invert Channel: CH2
Display Modes: CH1, CH2, ALT, Chop, ADD, X-Y
Maximum Input Voltage: 400V (DC or AC p-p)
TV Synch: Int (2 Div), Ext (0.5V p-p)
Auto Triggering: >20Hz
External Trigger Input:
Impedance: 1MΩ ±5% + 20pF Capacitance
Maximum Input Voltage: 160V (DC or AC peak)
Horizontal Sweep
Sweep Times: 200ns/Div to 0.5s/Div in 20 steps (1-2-5 seq);
(X10 Mag: 20ns/Div to 50ms/Div)
Mag: X10
Accuracy: ±3% (8% X10 Mag)
Sweep Modes: TV, Normal, Auto and p-p Auto
X-Y Mode
Inputs: X-Axis (CH1), Y-Axis (CH2)
Sensitivity: Same as CH1
Accuracy: ±5%
Frequency Response (-3dB):
DC: 0Hz to 1MHz, AC: 10Hz to 1MHz
Maximum Voltage: Same as CH1
X-Y Phase Difference: <3° from DC to 50KHz
Triggering
Source: CH 1, CH 2, ALT, Line and EXT
Slope: Positive or Negative adjustable levels
Coupling: AC
Sensitivity:
Int: DC to 10MHz (1 Div), DC to 20MHz (1.5 Div)
Ext: DC to 10MHz (0.3 p-p), DC to 20MHz (0.5 p-p)
2
Z Axis Modulation
Sensitivity: 5V p-p
Maximum Input Voltage: 50V or AC p-p
Polarity: Intensity increases as the voltage increases
Input Resistance: 10KΩ
Bandwidth (-3dB): DC to 1MHz
Calibrator Signal
Waveform: Square Wave
Amplitude: 0.5V ±3% p-p
Frequency: 1KHz ±2%
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
CRT
Size: 8cm x 10cm (3.15" x 3.94")
Acceleration Voltage: 2KV
General Specifications
Power Requirements: AC Input Voltage: 120V or 220V
Frequency: 50/60Hz
Power Consumption: 40W
Operating Temperature: 0 to 40°C (32 to 104°F)
Size: 5.1" (H) x 12.5" (W) x 15.75" (D)
Weight: 16 lbs
Accessories: Manual, Line cord, X1/X10 Probes (2)
30 MHz Dual Trace Oscilloscope
with Component Tester
6030C
K 30 MHz Vertical Bandwidth (-3dB)
K LCR Component Tester
K Alternate Trigger for a stable display of unrelated signals
K X5 Mag for Vertical Input and X10 for Horizontal
K TV Synch Filter
K Trigger Signal Output
K High Brightness CRT with Internal Graticule
CE
6030C
SPECIFICATIONS
Vertical Amplifier
(CH 1 and CH 2)
Sensitivity: 5mV/Div to 20V/Div in 12 steps (1-2-5 seq);
1mV/Div to 4V/Div (X5 Mag)
Mag: X5
Accuracy: ±3% (5% in X5 Mag)
Bandwidth (-3dB): DC: 0Hz to 30MHz, AC: 10Hz to 30MHz
Rise Time: < 18ns (<70ns in X5 Mag)
Input Impedance: Res: 1MΩ ±5%, Cap: 30pF
Input Coupling: AC, DC, GND
Invert Channel: CH2
CH1/CH2 Trigger Output: 100mV/Div into 50Ω
Display Modes: CH1, CH2, ALT, Chop, ADD, X-Y
Maximum Input Voltage: 400V (DC or AC peak)
Horizontal Sweep
Sweep Times: 100ns/Div to 0.2s/Div in 20 steps (1-2-5 seq);
10ns/Div to 20ms/Div (X10 Mag)
Mag: X10
Accuracy: ±3% (8% X10 Mag)
Sweep Modes: TV, Normal and Single
Triggering
Source: CH 1, CH 2, ALT, Line and EXT
Slope: Positive or Negative adjustable levels
Coupling: AC, DC, Normal/TV
Sensitivity:
Int: DC to 20MHz 1 Div, Ext: 0.3V p-p),
TV Int: 2 Div, Ext: 0.3V p-p
Trigger Lock: 50Hz to 10MHz 2 Div
External Trigger Input:
Impedance: 1MΩ ±5%
Maximum Input Voltage: 400V (DC or AC p-p)
Component Test
A 60Hz, 9V RMS signal is applied to the CH1 and CH2 input
when the AC, DC, GND is in the GND position and the
component test button is pushed in.
Z Axis Modulation
Minimum Input Level: TTL
Maximum Input Voltage: 50V or AC p-p
Polarity: Intensity increases as the voltage decreases
Input Resistance: 10KΩ
Bandwidth (-3dB): DC to 5MHz
General Specifications
CRT: 8cm x 10cm (3.15" x 3.94")
Power Requirements: AC Input Voltage: 120V or 220V
Frequency: 50/60Hz
Power Consumption: 35W
Operating Temperature: 0 to 40°C (32 to 104°F)
Size: 5.1" (H) x 12.2" (W) x 16.45" (D)
Weight: 14.3 lbs
Accessories: Manual, Line cord, X1/X10 Probes (2),
Test Leads
X-Y Mode
Inputs: X-Axis (CH1), Y-Axis (CH2)
Sensitivity: Same as CH1
Frequency Response (-3dB):
DC: 0Hz to 1MHz, AC: 10Hz to 1MHz
Maximum Voltage: Same as CH1
X-Y Phase Difference: <3°
Calibrator Signal
Waveform: Square Wave
Amplitude: 0.5V ±2% p-p
Frequency: 1KHz ±2%
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
3
820
840
860
Hand-Held DSO/DMM
K 20Mhz [820], 40MHz [840], 60MHz [860] bandwidths
K Models 840 and 860 include FFT
K Built in High accuracy 6000 count True RMS DMM
K 125KB record length for each channel
K 200MS/s sampling rate single channel and 100MS per
K 10 waveforms and setups may be stored and recalled
channel in dual channel [840, 860], 100MS/s [820]
K 2.5GHz Equivalent sampling [840] and 5GHz Equivalent
K USB interface and optional flash memory port [840, 860]
K High Resolution 320x 240 pixel Monochrome LCD
K Edge/Pulse width, TV/Pattern and Delay trigger modes
sampling [860]
K 20 automatic waveform Measurements
K Self test and Self calibration
K Help menu
820, 840, 860
SPECIFICATIONS
Vertical
No inputs: 2
Analog bandwidth: [820] 20MHz, [840] 40MHz, [860] 60MHz
Rise Time: [820] <17.5ns, [840] < 8.75ns, [860] < 5.83ns
Sensitivity: 5mV to100V/div (in a 1,2,5 sequence)
Resolution: 8 bit
Offset: ±5 div from the center
Vertical Accuracy: ±3 %
Input Impedance: 1MΩ ±1% and 20pF ±1.3pF
Max input V: 300V DC or AC peak
Probe Attenuation: x1 and x10
Horizontal:
Sweep rates: [820] 50ns/Div to 50s/Div, [840] 10ns/Div to
50s/Div, [860] 5ns/Div to 50s/Div
Time base Accuracy: ±0.01%
Acquisition system:
Acquisition Modes: Sample, Peak detect, Envelope, Average
Sampling: Real Time and Equivalent [840, 860]
Sample Rates: [820] 100MS/s, [840, 860] 200MS/s single
channel and 100MS/s per channel Dual channel
Equivalent Sampling: [840] 2.5GS/s, [860] 5GS/s
Sample Rate Accuracy: 100ppm
Record Length: 125KB/Channel
Waveform Interpolation: Dot, Linear, Sine, and Pulse
Peak Detect: 10ns minimum
Averages: 2 to 256
Trigger
Sensitivity: 0.5 Div (DC to 5MHz)
Trigger Types: Edge, Pulse width, Video
Coupling: AC, DC HF-Reject, LF-Reject, Noise Reject
4
Modes: Normal, Single, Roll, Auto
Trigger Level Range: ±20 Div from the center of the screen
Trigger Level accuracy: ±0.4 Div
Trigger sources: CHA and CHB
Video Trigger
Video Trigger sensitivity: 0.7 Div
Video Type: NTSC, PAL, Secam
Measurements:
Types: P-P, Max, Amplitude, Top, Base, Pos/Neg over shoot,
Pre-shoot, RMS, Mean, One cycle mean, Freq., Period,
±Width, ±Duty cycle, Rise/Fall time, Delay and Phase shift
Math Operations:
CHA+CHB, CHA-CHB, CHB-CHA, FFT [840, 860]
Cursors: gV, gT
FFT: [840, 860]
Weighting:
Rectangular, Hamming, Hanning and Blackman-Harris
Amplitude display: 1, 2, 5, 10dB/Div
Maximum Frequency: 1.25GHz
Memory: 10 waveforms and settings saved and recalled
DMM
DC Volts:
Range: 600mV to 1000V
Accuracy: ±(0.3% + 10d)
Best Resolution: 100µV
Impedance: 10MΩ
Overload protection: 1000VDC or AC peak
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
AC Volts:
Range: 6V to 600V
Accuracy: ±(0.75% + 10d) 50Hz to 1KHz;
±(2.0% + 10d) 1KHz to 30KHz
Best Resolution: 1mV
Impedance: 10MΩ
Overload protection: 1000VDC or AC peak
Resistance
Range: 600Ω to 60MΩ
Accuracy: ±(0.5% + 10d)
Best Resolution: 100mΩ
Overload Protection: 250V DC or AC peak
Capacitance
Range: 60nF to 300µF; Accuracy: ±(2.0% + 10d)
Other measurements
Diode test accuracy: ±2%
Continuity: Buzzer will sound < 60Ω
dBm with reference impedances of
2,4,8,16,50,75,93,110,125,135,150,300,600,900, 1K or 1.2KΩ
High current: to 600A with external current Clamp
Temperature (with Probe): to 600ºC (1112ºF)
General Specifications
Size: 8.3" (H) x 4.2" (W) x 2.2" (D); Weight: 2.6 lbs
Power: 9VDC @ 1A AC/DC adapter, 7.2V NIMH rechargeable
battery pack
Standard accessories: AC/DC adapter, User's manual, Scope
probe (2), Holster, Test Leads, USB cable and software
Optional accessories: Battery pack, Temperature adapter,
Clamp-on current probe, Carrying Bag and USB flash memory
820
Hand-Held DSO/DMM
OSCILLOSCOPE INPUT
CHA
840
860
Main Display waveforms and indicators
Oscilloscope
CHB
AC Power Adapter
& Internal charger
USB (mini) PC
Communication
320 x 240 pixel
LCD Display
with Backlight
Contrast
Adjustment
USB
Flash memory Host
Software key
HOLD/SAVE
HELP
POWER
AUTO
SCOPE
METER
CH1 and CH2 waveforms, along with the
Dual channel Math waveform, trigger levels,
horizontal positions, offsets, V/div and
Time/division settings are displayed.
Meter
Measure
Cursor
Encoder S/W
for easy and
Fast access
MULTIMETER INPUT
Volts Resistance, Capacitance,
Diode, Continuity, Aux
(Temperature, Currents, Humidity, Pressure)
Analog Bargraph, MIN, MAX, AVG
VOLT, DC, etc.
FEATURES
Record Length
Math
A long record length and high-speed sampling rates allows
the user to capture and view a more detailed “picture” of
a complex Waveform and it components. Up to 125kB samples
of waveform information may be captured and accurately
displayed on the LCD screen as show in the illustration below.
Dual channel Math functions are available for
adding and subtracting waveforms applied to
the CHA and CHB inputs. The FFT allows you to
view a waveform spectrum using a Rectangular,
Hamming, Hanning or Black Man-Harris window.
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
5
S2401
50MS/s, 1MHz Hand-Held DSO/DMM
K Dual Channel
K 50MS/s sampling rate
K 500mV/Div Vertical sensitivity
K Auto ranging Vertical and Horizontal scales
K Built-in auto/manual ranging, True RMS, 4000 count DMM
K DC to 1MHz bandwidths
K Hand held and battery operated
K Designed to UL3111, CSA C22.2 No 1010 standards
K RS-232 Port and supplied software
K User-friendly front panel
S2401
SPECIFICATIONS
Vertical (Oscilloscope)
Bandwidth: 1MHz
Resolution: 8 bits
Number of Channels: 2
Coupling: AC and DC
Input Impedance: 1MΩ
Accuracy: ±3%
Max. Input Volts: 600V DC or AC RMS
Vertical Sensitivity: 500mV/Div to 500V/Div in a 1-2-5
sequences
Horizontal (Oscilloscope)
Sample Rate:
50MS/s single channel
25MS/s dual channel
Record Length:
512 bytes single shot and Glitch capture
256 bytes all other modes
Samples/Div: 25 samples
Update Rate: Real time
Modes: Single shot, roll mode, normal
Accuracy: ±0.01%
Sweep Rate: 1µs/Div to 5s/Div in a 1-2-5 sequences
Memory: 16 waveforms and setups may be saved in memory
Triggering (Oscilloscope)
Trigger source: CH A, CH B, External
Coupling: AC, DC
Trigger sensitivity: 2/20 Division
Trigger Modes: Auto and Normal
Slope: Positive and Negative
6
DC Volts
(Digital Multimeter)
Ranges: 5V, 50V, 500V, 1000V
Best Resolution: 1mV
Accuracy: ±(0.3% + 3d)
Input Impedance: 1MΩ
AC Volts
Ranges: 3V, 30V, 300V, 750V
Best Resolution: 1mV
Accuracy:
±(0.75% + 5d) 40Hz to 450Hz
±(2% + 5d) 450Hz to 5KHz
±(2.5% + 5d) 5KHz to 20KHz
Input Impedance: 1MΩ
Max. Input Volts: 600V DC or AC RMS
Ohms
Ranges: 5KΩ, 50KΩ, 500KΩ, 5MΩ
Best Resolution: 1Ω
Accuracy: ±(0.5% + 5d)
Overload Voltage: 600V DC or AC peak
Continuity
Test Voltage: 1.7V
Threshold: 100 digits
Overload Voltage: 600V DC or AC peak
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Frequency
Ranges: 100Hz, 1KHz, 10KHz, 100KHz, 1MHz, 10MHz
Best Resolution: 0.01Hz
Accuracy: ±(0.05% + 5d)
Overload Voltage: 600V DC or AC peak
RPM
Range: 240 to 60,000 RPM
Resolution: 1 RPM
Accuracy: ±(0.05% + 5d)
Pulse Width
Range: 2µs to 500Ms (pulse width > 2µs)
Duty Cycle
Range: 25% to 75%
LCD Display
Size: 2.5" x 2.5"
General Specifications
Power:
4.8V NiMh battery pack
120V to 9V @ 1A DC adapter
Battery Life:
4 hours without backlight
3 hours with backlight on
Display: 132 x 128 Pixel super twist LCD
Size: 7.5" (H) x 3.5” (W) 1.57” (D)
Weight: 1.5 lbs
Standard Accessories: Manual, Carrying case, Test leads,
Holster, RS-232 cable, Software, AC/DC charger
50MS/s, 5MHz Hand-Held DSO/DMM
S2405
K Dual Channel
K 50MS/s sampling rate
K 50mV/Div Vertical sensitivity
K Auto ranging Vertical and Horizontal scales
K Built-in auto/manual ranging, True RMS, 4000 count DMM
K DC to 5MHz bandwidths
K Hand held and battery operated
K Designed to UL3111, CSA C22.2 No 1010 standards
K RS-232 Port and supplied software
K User-friendly front panel
S2405
SPECIFICATIONS
Vertical (Oscilloscope)
Bandwidth: 5MHz
Resolution: 8 bits
Number of Channels: 2
Coupling: AC and DC
Input Impedance: 1MΩ
Accuracy: ±3%
Max. Input Volts: 600V DC or AC RMS
Vertical Sensitivity: 50mV/Div to 500V/Div in a 1-2-5
sequences
Horizontal (Oscilloscope)
Sample Rate:
50MS/s single channel
25MS/s dual channel
Record Length:
512 bytes single shot and Glitch capture
256 bytes all other modes
Samples/Div: 25 samples
Update Rate: Real time
Modes: Single shot, roll mode, normal
Accuracy: ±0.01%
Sweep Rate: 1µs/Div to 5s/Div in a 1-2-5 sequences
Memory: 16 waveforms and setups may be saved in memory
Triggering (Oscilloscope)
Trigger source: CH A, CH B, External
Coupling: AC, DC
Trigger sensitivity: 2/20 Division
Trigger Modes: Auto and Normal
Slope: Positive and Negative
DC Volts
(Digital Multimeter)
Ranges: 5V, 50V, 500V, 1000V
Best Resolution: 1mV
Accuracy: ±(0.3% + 3d)
Input Impedance: 1MΩ
AC Volts
Ranges: 3V, 30V, 300V, 750V
Best Resolution: 1mV
Accuracy:
±(0.75% + 5d) 40Hz to 450Hz
±(2% + 5d) 450Hz to 5KHz
±(2.5% + 5d) 5KHz to 20KHz
Input Impedance: 1MΩ
Max. Input Volts: 600V DC or AC RMS
Ohms
Ranges: 5KΩ, 50KΩ, 500KΩ, 5MΩ
Best Resolution: 1Ω
Accuracy: ±(0.5% + 5d)
Overload Voltage: 600V DC or AC peak
Continuity
Test Voltage: 1.7V
Threshold: 100 digits
Overload Voltage: 600V DC or AC peak
Frequency
Ranges: 100Hz, 1KHz, 10KHz, 100KHz, 1MHz, 10MHz
Best Resolution: 0.01Hz
Accuracy: ±(0.05% + 5d)
Overload Voltage: 600V DC or AC peak
RPM
Range: 240 to 60,000 RPM
Resolution: 1 RPM
Accuracy: ±(0.05% + 5d)
Pulse Width
Range: 2µs to 500Ms (pulse width > 2µs)
Duty Cycle
Range: 25% to 75%
LCD Display
Size: 2.5" x 2.5"
General Specifications
Power:
4.8V NiMh battery pack
120V to 9V @ 1A DC adapter
Battery Life:
4 hours without backlight
3 hours with backlight on
Display: 132 x 128 Pixel super twist LCD
Size: 7.5" (H) x 3.5” (W) 1.57” (D)
Weight: 1.5 lbs
Standard Accessories: Manual, Carrying case, Test leads,
Holster, RS-232 cable, Software, AC/DC charger
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
7
303
Power Supplies
with Analog Displays
310
K Continuously variable Voltage and Current output
K Short circuit and overload protected
K Separate meters for monitoring voltage and current
K Excellent regulation and ripple specs
K Constant Voltage and Constant current indicators
K Ideal for the service bench
K Cost effective
303
310
SPECIFICATIONS
[ 303 ]
[ 310 ]
General Specifications
AC Input Volts: 120/220V selectable
Power Consumption: 190VA
Operating Temperature: 0 to 40°C (32 to 104°F)
Size: 5.0” (H) x 6.3” (W) × 13.0” (D)
Weight: 14 lbs
Supplied Accessories: Manual, Line cord, Test leads
General Specifications
AC Input Volts: 120/220V selectable
Power Consumption: 520VA
Operating Temperature: 0 to 40°C (32 to 104°F)
Size: 5.0” (H) x 6.3” (W) × 13.0” (D)
Weight: 26 lbs
Supplied Accessories: Manual, Line cord, Test leads
Output Voltage Range: 0 to ±30V
Output Current Ranges: Range 1: 0 to 3A;
Range 2: 0 to 600mA
Load Regulation: Constant Voltage: 0.01% + 3mV
Constant Current: 0.2% + 3mA
Line Regulation: Constant Voltage: 0.01% + 3mV
Constant Current: 0.2% + 3mA
Ripple: Constant Voltage: 2mV RMS
Constant Current: 2mA RMS
Readout: Analog for both voltage and current
Meter Accuracy: ±5% of full scale for both voltage
and current
8
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Output Voltage Range: 0 to ±30V
Output Current Ranges: Range 1: 0 to 10A;
Range 2: 0 to 2A
Load Regulation: Constant Voltage: 0.04% + 2mV
Constant Current: 0.4% + 2mA
Line Regulation: Constant Voltage: 0.05% + 3mV
Constant Current: 0.4% + 5mA
Ripple: Constant Voltage: 1mV RMS
Constant Current: 1mA RMS
Readout: Analog for both voltage and current
Meter Accuracy: ±5% of full scale for both voltage
and current
Single Output Power Supplies
with Digital Displays
1805 Single Output Power Supply
1805
3003B
3003B Single Output Power Supply
K Excellent Load, Line and Ripple specs
K 0 to ±30V with 0 to ±3 Amps Load current
K Constant Voltage and Constant current operation
K Fully Isolated outputs terminals
K Units can be connected together in series for Higher
K 0 to ±18 Volts with 0 to ±5Amps load current
K 3 digit Led displays for both current and Voltage
K Small case size
K Front panel Indicators for constant current and constant
voltage operation
K Short circuit and Reverse Voltage protected
output voltage
K Course and Fine controls for accurate Voltage settings
K Low noise and Linear supply for powering sensitive
circuits
K Front panel push button switch disconnects power
supply from Load
1805
3003B
SPECIFICATIONS
[ 1805 ]
[ 3003B ]
Output Volts: 0 to ±18V DC
Output Amps: 0 to ±5A
Constant Voltage Mode:
Load Regulation: 0.05% + 5.6mV
Line Regulation: 0.05% + 5.6mV
Ripple and Noise: 0.5mV RMS
Constant Current Mode:
Load Regulation: 0.05% + 20mA
Line Regulation: 0.05% + 8mA
Ripple and Noise: 5mA RMS
Digital Display:
Type: 3 digit red LED
Resolution: Volts: 100mV; Amps: 10mA
Accuracy: Volts: ±(0.2% + 2d); Current: ±(1% + 3d)
Output Volts:
0 to ±30 V DC
Output Amps:
0 to ±3 Amps
Constant Voltage Mode:
Load and Line Regulation: 0.02% + 2mV
Ripple and Noise: 1mV RMS
Constant Current Mode:
Load Regulation: 0.05% + 5mA
Line Regulation: 0.05% + 0.25mA
Ripple and Noise: 2mA RMS
Digital Display Resolution:
Volts: 100mV; Amps: 10mA
Accuracy: ±(0.5% + 3d)
General Specifications
AC Input Voltage: 120/220V selectable
Power Consumption: 170VA
Operating Temperature: 0 to 32°C (32 to 90°F)
Size: 6.3" (H) x 5.0" (W) x 13.0" (D)
Weight : 15 lbs
Supplied Accessories: Manual, Line cord, Test leads
General Specifications
AC Input Voltage: 120/220V selectable
Power Consumption: 190VA
Operating Temperature: 0 to 32°C (32 to 90°F)
Size: 6.3" (H) x 5.0" (W) x 13.0" (D)
Weight : 15 lbs
Supplied Accessories: Manual, Line cord, Test leads
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
9
3005B
3006B
Single Output Power Supplies
with Digital Displays
3005B Single Output Power Supply
3006B Single Output Power Supply
K 0 to ±30V with 0 to ±5 Amps Load current
K Internal fan for cooler operation
K 0 to ±60V with 0 to ±1.5 Amps Load current
K Excellent Line, Load and Ripple specifications
K Excellent Line, Load and Ripple specifications
K Small case size
K Short Circuit and Reverse Voltage protected
K Constant Voltage and Constant Current operation
K Designed with energy saving circuitry
K Fully isolated output terminals for series operation
K 3 digit Led displays for both current and Voltage
K Front panel Indicators for Constant Voltage and
K Short circuit and Reverse Voltage protected
constant current operation
3005B
3006B
SPECIFICATIONS
10
[3005B]
[3006B ]
Output Volts:
0 to ±30V DC
Output Amps:
0 to ±5Amps
Constant Voltage Mode:
Load and Line Regulation: 0.02% + 2mV
Ripple and Noise: 1mV RMS
Constant Current Mode:
Load Regulation: 0.05% + 5mA
Line Regulation: 0.05% + 0.25mA
Ripple and Noise: 2mA RMS
Digital Display:
Resolution: Volts: 100mV; Amps: 10mA
Accuracy: ±(0.5% + 3d)
Output Volts:
0 to ±60V DC
Output Amps:
0 to ±1.5A
Constant Voltage Mode:
Load and Line Regulation: 0.02% + 2mV
Ripple and Noise: 1mV RMS
Constant Current Mode:
Load Regulation: 0.05% + 5mA
Line Regulation: 0.05% + 0.25mA
Ripple and Noise: 2mA RMS
Digital Display:
Resolution: Volts: 100mV; Amps: 10mA
Accuracy: ±(0.5% + 3d)
General Specifications
AC Input Voltage: 120/220V selectable
Power Consumption: 133VA
Operating Temperature: 0 to 32°C (32 to 90°F)
Size: 6.3" (H) x 5.0" (W) x 13.0" (D)
Weight : 15 lbs
Supplied Accessories: Manual, Line cord, Test leads
General Specifications
AC Input Voltage: 120/220V selectable
Power Consumption: 190VA
Operating Temperature: 0 to 32°C (32 to 90°F)
Size: 6.3" (H) x 5.0" (W) x 13.0" (D)
Weight : 15 lbs
Supplied Accessories: Manual, Line cord, Test leads
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Dual Output Power Supplies
with Digital Displays
3015B Dual Output Power Supply
3015B
3032B
3032B Dual Output Power Supply
K 0 to ±30V with ±1.5Amps load current
K Energy saver design allows cooler operation
K 0 to ±30V with ±3.0 Amps load current
K Low noise Linear supply for powering sensitive circuits
K Excellent Load, line and Ripples specs
K Front panel indicators for Constant Current and
K Fully isolated outputs for connecting outputs in series
K Excellent Load, line and Ripple specs
Constant Voltage operation
K Each output has two 3 digit LED displays for monitoring
K Energy Saver design for cooler operation
Voltage and current
3032B
3015B
SPECIFICATIONS
[ 3015B ]
[ 3032B ]
General Specifications
AC Input Voltage: 120/220V
Power Consumption: 150VA, 50/60Hz
Operating Temperature: 0 to 35°C (32 to 95°F)
Size: 6.3" (H) × 9.2" (W) × 12.8" (D)
Weight: 16.5 lbs
Supplied Accessories: Manual, Line cord, Test Leads (2 sets)
General Specifications
AC Input Voltage: 120/220V
Power Consumption: 300VA, 50/60Hz
Operating Temperature: 0 to 35°C (32 to 95°F)
Size: 6.3" (H) × 9.2" (W) × 12.8" (D)
Weight: 20 lbs
Supplied Accessories: Manual, Line cord, Test Leads (2 sets)
Outputs 1 and 2
Volts: 0 to ±30V DC
Amps: 0 to ±1.5A
Constant Voltage Mode:
Load Regulation: 0.02% + 2mV
Line Regulation: 0.02% + 2mV
Ripple and Noise: 1mV RMS
Constant Current Mode:
Load Regulation: 0.05% + 5mA
Line Regulation: 0.05% + 0.25mA
Ripple and Noise: 2mA RMS
Digital Display:
Resolution: Volts: 100mV; Current: 10mA
Accuracy: ±(0.5% + 3d)
Outputs 1 and 2
Volts: 0 to ±30V DC
Amps: 0 to ±3A
Constant Voltage Mode:
Load Regulation: 0.02% + 2mV
Line Regulation: 0.02% + 2mV
Ripple and Noise: 1mV RMS
Constant Current Mode:
Load Regulation: 0.05% + 5mA
Line Regulation: 0.05% + 0.25mA
Ripple and Noise: 2mA RMS
Digital Display:
Resolution: Volts: 100mV; Current: 10mA
Accuracy: ±(0.5% + 3d)
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
11
3033B
3040T
Triple Output Power Supplies
with Digital Displays
3033B Triple Output Power Supply with
Digital Displays
K Dual 0 to ±30V with 0 to ±1.5 Amps Load current
outputs and a fixed 5Volt at 5 Amp output
K Both Variable outputs have a Voltage and Current
display
3040T Triple Output Power Supply with
Series/Parallel Tracking
K Outputs may be independent or connected in Series or
Parallel and are selectable from the front panel
K Fixed supply may be switched between 3.3V and 5.0V
K Series or Parallel Master/Slave tracking modes
K Energy saving design
K Series output tracking
K Small case size
K Excellent Line, Load and Ripple specifications
3033B
3040T
SPECIFICATIONS
[ 3033B ]
Outputs 1 and 2
Volts: 0 to ±30V DC
Amps: 0 to ±1.5A
Constant Voltage Mode:
Load and Load Regulation: 0.02% + 2mV
Ripple and Noise: 1mV RMS
Constant Current Mode:
Load Regulation: 0.05% + 5mA
Line Regulation: 0.05% + 0.25mA
Ripple and Noise: 2mA RMS
Digital Display (Outputs 1 & 2)
Resolution: Volts: 100mV; Current: 10mA
Accuracy: ±(0.5% + 3d)
Tracking Error: ±(0.5% + 10mV)
Output 3
Volts Max: 5V ±0.2.5%
Amps Max: 5A ±2.5%
Load Regulation: 0.2% + 2mV
Line Regulation: 0.2% + 2mV
General Specifications
AC input Voltage: 120/220V, 50/60Hz
Power Consumption: 192VA
Operating Temperature: 0 to 35°C (32 to 95°F)
Size: 6.3" (H) × 9.0" (W) × 13.0" (D)
Weight: 20 lbs
Supplied Accessories: Manual, Line cord, Test Leads (3 sets)
12
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
[ 3040T ]
Outputs 1 and 2
Volts: 0 to ±36V DC
Amps: 0 to 2.5A
Constant Voltage Mode:
Line and Load Regulation: 0.02% + 2mV
Ripple and noise: 0.2mV RMS, 4mV P-P
Constant Current Mode:
Load Regulation: 0.05% + 5mA
Line Regulation: 0.05% + 0.25mA
Ripple and Noise: 2mA RMS, 10mA P-P
Digital Display (Outputs 1 and 2)
Resolution: Volts: 100mV; Current: 10mA
Accuracy: ±(0.5% + 1d)
Output 3
Volts Max: 3.3V / 5V ±2.5% (selectable)
Current Max: 5A ±2.5%
Load and Line Regulation: 0.1% + 5mV
Ripple: 2mV RMS
General Specifications
AC input Voltage: 120/220V, 50/60Hz
Power Consumption: 455VA
Operating Temperature: 0 to 35°C (32 to 95°F)
Size: 6.3” (H) x 9.0” (W) x 13.0” (D)
Weight: 16.5 lbs
Supplied Accessories: Manual, Line cord, Test Leads (3 sets)
Power Supplies with
LCD Digital Displays
3030
3030D
3030T
K Large LCD display with back light for displaying Voltage and Current settings
K Outputs may be connected in series or parallel (3030D and 3030T)
K Constant voltage and current selection switch
K Incremental switch for setting Max. current value
K Excellent line and load regulation characteristics
K Fully isolated outputs for series or parallel operation
K Automatic cooling fan operation
K 10-turn voltage control for precise voltage settings
K Extended (Barrier strip) output connection
3030
3030D
3030T
SPECIFICATIONS
[ 3030 Single Output]
[ 3030D Dual Output ]
[ 3030T Triple Output]
Output Volts: 0 to ±30V DC
Output Amps: 0 to ±3A
Constant Voltage Mode:
Load Regulation: 0.2% + 3mV
Line Regulation: 0.2% + 3mV
Ripple and Noise: 0.5mV RMS
Constant Current Mode:
Load Regulation: 0.3% + 3mA
Line Regulation: 0.3% + 3mA
Ripple and Noise: 3mA RMS
Digital Display:
Type: 3 digit LCD
Resolution Volts: 100mV
Resolution Amps: 10mA
Accuracy Volts: ±(0.2% + 2d)
Accuracy Amps: ±(1% + 3d)
Outputs 1 and 2
Volts: 0 to ±30V DC
Amps: 0 to ±3A
Constant Voltage Mode:
Load Regulation: 0.02% + 3mV
Line Regulation: 0.02% + 3mV
Ripple and Noise: 0.5mV RMS
Constant Current Mode:
Load Regulation: 0.3% + 3mA
Line Regulation: 0.3% + 3mA
Ripple and Noise: 3mA RMS
Digital Display :
Type: 3 digit LCD
Resolution Volts: 100mV
Resolution Amps: 10mA
Accuracy Volts: ±(0.2% + 2d)
Accuracy Amps: ±(1% + 3d)
Outputs 1 and 2
Volts: 0 to ±30V DC
Amps: 0 to 3A
Constant Voltage Mode:
Line and Load Regulation: 0.02% + 3mV
Ripple and noise: 0.5mV RMS
Constant Current Mode:
Load and Load Regulation: 0.3% + 3mA
Ripple and Noise: 3mA RMS
Digital Display :
Type: 3 digit LCD
Resolution Volts: 100mV
Resolution Amps: 10mA
Accuracy Volts: ±(0.2% + 2d)
Accuracy Amps: ±(1% + 3d)
General Specifications
AC Input Voltage: 120V only
Power Consumption: 160VA
Operating Temperature: 0 to 32°C (32 to 90°F)
Size: 7.5" (H) x 5.1" (W) x 11.0" (D)
Weight: 11 lbs
Supplied Accessories: Manual, Line cord, Test leads
General Specifications
AC Input Volts: 120/220V
Power Consumption: 305VA, 50/60Hz
Operating Temperature: 0 to 35°C (32 to 95°F)
Size: 7.5" (H) × 10.6" (W) × 13.0" (D)
Weight: 22 lbs
Supplied Accessories: Manual, Line cord,
Test Leads (2 sets)
Output 3
Volts Max: 5V
Current Max: 3A
Load and Line Regulation: 0.02% + 3mV
Ripple and Noise: 0.5mV RMS
General Specifications
AC input Voltage: 120/220V
Power Consumption: 310VA, 50/60Hz
Operating Temperature: 0 to 35°C (32 to 95°F)
Size: 7.5” (H) x 10.6” (W) x 13.0” (D)
Weight: 23.1 lbs
Supplied Accessories: Manual, Line cord, Test Leads
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
13
P6000
Programmable Power Supply
K All values may be entered from keyboard or rotary dial
K RS –232/485 interface with cable, adapter and software CD
K Volts, amps and power are displayed on a backlit LCD display
K 10 settings may be stored in memory
K Light weight and energy efficient
K Over voltage and current protection
K Outstanding in Production Test Applications
P6000
SPECIFICATIONS
Output Voltage
Range: 0 to ±36V
Voltage Resolution:
1mV: 0 to 3.999V
10mV: 4 to 36V
Output Amps
Range: 0 to ±3A
Amps Resolution: 1mA
Constant Voltage Mode
Load Regulation: ±0.02% + 10mV
Line Regulation: 0 to 3.999V: ±0.01% + 3mV
4 to 36V: ±0.02% + 10mV
Ripple: #1mV RMS
Constant Current Mode
Load Regulation: ±0.02% + 10mV
Line Regulation: ±0.02% + 10mV
Ripple and noise: #4mV Rms
Program Accuracy (25 °C)
Voltage: 0.1% + 20mV
Current: 0.1% + 20mA
14
Read Back Accuracy (25 °C)
Voltage: 0 to 19.999V: 0.2% + 20mV
20 to 36V: 0.2% + 100mV
Current: 0.2% + 20mA
Program Resolution
Voltage: 0 to 3.999V: 1mV; 4 to 36V: 10mV
Current: 1mA
Read back Resolution
Voltage: 0 to 19.999V: 10mV; 20 to 36V: 100mV
Current: 1mA
Interface
RS-232 adapter and cables
Software
Power MS Power Management software
ActiveX and DLL Support tools for VC++/VB /Delphi /LabView
(upon request)
Memory
10 Locations EEPROM for saving power settings
Protection
Over voltage, over current and power
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
General Specifications
AC Input Volts: 110/220V, 50/60Hz
Power Consumption: 200VA
Operating Temp: 0 to 50°C (32 to 120°F) at relative humidity of
0 to 80%
Size: 3.5” (H) x 8.3” (W) x 9.8" (D)
Weight: 13.2 lbs
Supplied Accessories: Manual, Line cord, Handels, RS-232
adapter and cables
Optional Accessories: USB adapter and cables
P6000
Programmable Power Supply
Configuration screen: Program up to 16 model P6000 Power Supplies from this screen.
Communication Setting: Used to configure
communication related settings.
Software
Main screen: Displays feedback from the hardware and allows the user to control various parameters directly from the computer software.
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
15
L300
Programmable 300W Electronic Load
K 300W Maximum Power
K Operates in Constant current, Constant resistance or Constant power modes
K 1mA current setting resolution
K Voltage, Current and Power are displayed on the back lit display
K Back light LCD
K Values may be enter from key board of rotary dial
K RS232 interface and control software
K Small size and light weight
L300
SPECIFICATIONS
Inputs:
1
Input Volts:
0 to 360V
Input Current:
0 to 30A
Input Power:
0 to 300W
Operating Modes:
Constant current, Constant Resistance or Constant power
Voltage Resolutions:
0.000V to 3.999V ±(0.2% + 3mV)
4.00V to 35.999V ±(0.2% + 30mV)
36.0V to 360.0V ±(0.2% + 30mV)
Current Resolutions:
0.000A to 2.999A ±(0.2% + 3mA)
3.00A to 35.999 A ±(0.2% + 3mA)
Current Setting Resolution:
1mA (0 to 2.999A), 10mA (3.00A to 30A)
Power Setting Resolution:
0.1W (0 to 300W)
Resistance Setting Resolution:
0.01Ω (0 to 99.99Ω), 0.1Ω (100 to 500Ω)
16
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Minimum Resistance:
< 0.08Ω
Ripple:
< 10mV P-P
Protection:
Over Voltage, Over Current, Over power, Over Heating and
Reverse polarity
Power:
120/220V, 50/60Hz
Communication:
RS232 or RS485
Memory:
10 setups may be stored and recalled
Software:
Monitor software CD. ActiveX modules for VC++, Visual basic,
Delphi and LabView upon request.
General Specifications
Size: 3.5" (H) x 8.3" (W) x 9.8" (D)
Weight: 11 lbs
Supplied Accessories: Manual, Line cord, Handles, RS-232
adapter and Cables
Optional Accessories: USB adapter and Cable
Programmable 300W Electronic Load
Configuration screen: Allows the user to set various parameters for the program.
L300
Communication Setting: Used to
configure communication related settings.
Software
Main screen: Displays feedback from the hardware and allows the user to control various parameters directly from the computer software.
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
17
Loop Calibrator
30C
K
24 volt internal loop supply
K
Auto Step and Auto ramp modes; no need for external mA meter
K
Simultaneous mA and % read out fo quick, easy interpretation of reading
K
1µA resolution for mA source, simulate and measure
K
25% step button for quick linearity tests
K
Large 4 ½ digit 20,000 count LCD display
K
Encoder dial for easy one handed operation
mA Source Display
30C
Loop Power Display
Voltage Source Display
Voltage Measure Display
Simulator Display
SPECIFICATIONS
Measurements:
Voltage:
Ranges: 2, 20, 50Volts
Best Resolution: 100µV
Accuracy: ±(0.05% + 5d)
Overload Protection: 100VDC or AC peak
Current:
Ranges: 2mA and 20mA
Accuracy: ±(0.05% + 5d)
Best Resolution: 0.1µA
Sourcing
Current:
Range: 4 to 20mA (Values from 0 to 24mA maybe obtained
through overlapping)
Accuracy: ±(0.025% + 5d)
Loop power: 24V
Voltage
Range: 2V and 20V
Accuracy: ±(0.05% + 5d)
TX simulator
Type: 2-wire transmitter simulation
External Excitation Voltage: 3V min to 50V max
Simulation current: 4 to 20mA (Values from 0 to 24mA maybe
obtained through overlapping)
Output current Ramp:
Range: 4mA to 20mA
Ramp Times: 5s, 20s, 50s
18
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
General Specifications:
Operating Temperature: -10 to 55ºC (14 to 131ºF)
Power: (1) 9V ANSI/NEDA 1604 battery
Size: 7.0" (H) x 3.5"(W) x 1.5" (D)
Weight: 10.5 oz
Accessories: Test Leads, Instruction manual, carrying case
and 9 Volt battery
Bench Top Digital Multimeter
3-3/4 Digit DMM with RS-232
B940
K True RMS AC volts and amps measurements
K Capacitance and Frequency measurements
K Back-lit display and Auto/Manual ranging
K MIN/MAX and Relative mode
K Delay hold mode
K AC Line or Battery Operated
K RS-232 Interface with software
K Portable or Bench with Pop-up Stand
K Storage Compartment
B940
Software Display
SPECIFICATIONS
DC Voltage
Range: 400mV, 4V, 40V, 400V and 1000V
Best Resolution: 0.1mV
Accuracy: ±(0.3% + 2d)
Resistance
Range: 400Ω , 4K Ω , 40KΩ, 400KΩ, 4MΩ, 40MΩ
Best Resolution: 0.1Ω
Accuracy: ±(0.5% + 5d)
AC Voltage
Range: 4V, 40V, 400V and 750V
Best Resolution: 1.0mV
Accuracy: ±(0.8% + 5d)
Frequency
Range: 100Hz, 1KHz, 10KHz and 600KHz
Best Resolution: 0.01Hz
Accuracy: ±(0.1% + 2d)
DC Current
Range: 4mA, 40mA, 400mA and 10A
Best Resolution: 1µA
Accuracy: ±(0.8% + 5d)
Capacitance
Range: 4nF, 40nF, 400nF, 4µF, 40µF
Best Resolution: 0.1pF
Accuracy: ±(2% + 4d)
AC Current
Range: 4mA, 40mA, 400mA and 10A
Best Resolution: 1µA
Accuracy: ±(1.5% + 5d)
Diode test
Test Volt: 3 V
Test Current: 0.6mA
General Specifications
Size: 3.3" (H) x 9.0” (W) x 9.4” (D)
Weight: 3.3 lbs
Power: 9V NEDA battery (not supplied) or 90 to
132VAC / 198 to 264VAC @ 50/60Hz (Adapter Supplied)
Accessories: Manual, Test leads, Carrying strap,
Line cord, RS-232 cable, Software CD
Continuity
Buzzer: will sound at < 40Ω Resistance
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
19
B4100
Bench Top Digital Multimeter
5-1/2 Digit Programmable
K 5-1/2 Digit multimeter with selectable count resolutions up to 200,000
K True RMS and measures frequency
K Selectable Count Resolutions: 2K, 20K, 200K
K Auto-ranging
K Trend plot display
K RS-232 interface standard and optional GPIB interface
K Min/Max/Avg, Relative error and comparison functions
K May be used on line voltages from 85V to 250V without any internal changes
K Software included
K Seven setups may be stored and recalled in memory
B4100
SPECIFICATIONS
[ B4100 ]
Display
Slow: Counts: 200,000; Digits: 5 ½
Medium: Counts: 20,000; Digits: 4 ½
Fast: Counts: 2,000; Digits: 3 ½
Specifications (at 25°C ±5°C, 77°F ±9°F)
DC Voltage
Ranges: 2V, 20V, 200V, 1000V
Best Resolutions:
10µV (Slow), 100µV (Med), 1mV (Fast)
Accuracy: ±(0.05% + 3d)
Input Impedance: 10MΩ
Overload Protection: 1000V
AC Volts
Ranges: 2V, 20V, 200V, 1000V
Best Resolutions: 100µV (Slow and Med), 1mV (Fast)
Accuracy: ±(0.5% + 5d) 45Hz to 450Hz
Overload Protection: 1000V
Crest Factor: 3:1
AC Current
Best Resolutions:
200µA: 10nA (Slow and Med), 100nA (Fast)
200mA: 1µA (Slow), 10µA (Med), 100µA (Fast)
10A: 100µA (Slow), 1mA (Med), 10mA (Fast)
Accuracy: ±(0.5% + 5d), Max burden: 200mV
Overload Protection: 0.5A/250V and10A/250V fuse
Resistance
Ranges: 200Ω, 2KΩ, 200KΩ, 2MΩ, 10MΩ
Best Resolutions:
1mΩ (Slow), 10mΩ (Med), 100mΩ (Fast)
Accuracy: ±(0.05% + 5d)
Overload Protection: 250V or AC RMS
Frequency
Ranges: 200Hz, 2KHz, 20KHz, 200KHz
Best Resolutions:
1mHz(Slow), 10mHz (Med), 100mHz (Fast)
Accuracy: ±(0.05% + 2d)
Overload Protection: 250V DC or AC RMS
DC Current
Ranges: 200µA, 200mA, 10A
Best Resolutions:
200µA: 1nA (Slow), 10nA (Med),100nA (Fast)
200mA: 1µA (Slow), 10µ (Med), 100µA (Fast)
10A: 100µA (Slow), 1mA (Med), 10mA (Fast)
Accuracy: ±(0.1% + 5d), Max burden: 200mV
Overload Protection: 0.5A/250V and 10/250V fuse
20
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Diode
Range: 2V
Test Current: Approximately 1.0mA
Test Volts: Approximately 3V
Continuity: Buzzer will sound at 100Ω or less
Interface
Type: RS-232
Connector: 9 Pin din
Baud Rate: 1200, 2400, 4800 or 9600 bps
GPIB: optional
General Specifications
Display: 128 x 64 pixel super twist LCD
Size: 3.3” (H) x 9.5” (W) x 10.5” (D)
Weight: 3.2 lbs
Operating Temperature: 0 to 50°C (32 to 120°F)
Power: 85V to 275V ±10%
Supplied Accessories: Manual, Line cord, Software disk,
RS-232 cable, Test Leads
Optional Acessories: GPIB interface
Bench Top Digital Multimeter
4 1/2 Digit DMM
B845
K 4-1/2 digit LCD display with polarity indicator
K 0.05% DC voltage accuracy
K 10µV AC & DC voltage resolution
K 10nA current resolution
K 10mΩ Resistance resolution
K Data hold switch
K Measures current to 10 Amps
K 200µA AC/DC Current Range
B845
SPECIFICATIONS
DC Voltage
Range: 200mV, 2V, 20V, 200V, 1000V
Best Resolution: 10µV
Accuracy: ±(0.05% Rdg + 2d)
AC Voltage
Range: 200mV, 2V, 20V, 200V, 1000V
Best Resolution: 10µV
Accuracy: ±(0.5% Rdg + 10d)
DC Current
Range: 200µA, 2mA, 20mA, 200mA, 10A
Best Resolution: 10nA
Accuracy: ±(0.3% Rdg + 3d)
Continuity
Buzzer: Will sound at < 200Ω Resistance
Diode test
Test Volt: 2.8V
Test Current: 3mA
General Specifications
Operating Temperature: 0 to 40°C (32 to 104°F) at a relative
humidity of 0 to 80%
Power: 115/230V, 50/60Hz
Size: 3.0" (H) × 8.0" (W) × 10.5" (D)
Weight : 5 lbs
Supplied Accessories: Manual, Line cord, Test leads
AC Current
Range: 200µA, 2mA, 20mA, 200mA, 10A
Best Resolution: 10nA
Accuracy: ±(0.75% Rdg + 10d)
Resistance
Range: 200Ω, 2KΩ, 20KΩ, 200KΩ, 2MΩ, 20MΩ
Best Resolution: 10mΩ
Accuracy: ±(0.2% Rdg + 5d)
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
21
6800
80,000 Count Digital Multimeter
K 80,000 count Dual Display
K Basic DC accuracy is 0.05%
K Pulse output with frequency selection from 0.5Hz to 5KHz
with duty cycles from 1% to 99%
K Measures frequency, ms Pulse width and duty cycle
K AC and AC+DC TRUE RMS measurements.
K Hi and Lo limit testing
K dBm measurement using 20 reference Impedances
K Min/Max/AVG
K Peak hold and Relative mode
K RS232 port
K CE and Category II 1000V and Cat III 600V safety standards
K Built in 10 hour timer
6800
SPECIFICATIONS
mV DC
Ranges: 80 mV, 800 mV; Best Resolution: 1µV
Accuracy: ±0.05% + 10d; Input Impedance: 1GΩ
DC Volts
Ranges: 8V, 80 V, 800V, 1000V; Best Resolution: 100µV
Accuracy: ±(0.05% + 10d); Max. Input Voltage: 1000V DC
Input Impedance: 10MΩ
AC mV/Volts TRUE RMS
Ranges: 80mV, 800mV, 8V, 80V, 750V
Best Resolution: 1µV
AC Volts Accuracy (80mV, 800mV, 8V ranges):
50/60Hz: ±(0.5% + 10d)
50Hz ~ 1KHz: ±(1.0% +10d)
1KHz ~ 10KHz: ±(3.0% + 10d)
10KHz ~ 20KHz: ±(5.0% + 10d)
AC Volts Accuracy (80V and 750V Range):
1% from 50Hz to 400Hz
AC + DC V Accuracy: ±(1.0%+ 10d) 50Hz to 200Hz
Max. Input Voltage: 1000 V DC or AC peak
Input Impedance: 10MΩ (1GΩ 80mV and 800mV)
DC Current
Ranges: 80mA, 800mA, 8A, 10A; Best Resolution: 1.0µA
Accuracy: ±(0.5% + 10d)
Overload Protection: 0.8A/250V fuse and 10A/250V fuse
22
AC True RMS Current
Ranges: 80mA, 400mA, 8A, 10A; Best Resolution: 1.0µA
Accuracy: ±(0.5% + 10d) 50Hz to 1KHz
Accuracy AC+DC Amps: ±(1.0% + 10d) 50Hz to 200Hz
Overload Protection: 800mA/250 fuse and 10A/250V fuse
Capacitance
Ranges: 1nF, 10nF, 100nF, 1µF, 10µF, 100µF.
Best Resolution: 1pF
Accuracy: ±(2.5% + 10d), (±5% + 10d), 1nF range
Maximum Input Volts: 250V
DBM
Range: -80dBm to +80dBm; Best Resolution: -0.01dBm
Accuracy: ±(1.0% or reading)
Default Ref impedance is 600Ω, Ref. Impedances from
4Ω to 1200Ω maybe selected
Temperature
Ranges: -50 to 1372°C (-58 to 2502°F)
Thermocouple: K type
Display: °C primary display °F secondary display
Resolution: 0.1°
Accuracy: ±(2.5% + 8d)
Resistance
Ranges: 800Ω, 8KΩ, 80KΩ, 800KΩ, 8MΩ, 80MΩ
Best Resolution: 10.0mΩ; Accuracy: ±(0.3% + 10d)
Max. Input Voltage: 250V
Diode and Continuity Test
Range: 8.00V; Accuracy: ±(3% + 10d)
The Buzzer sounds when the measured resistance is <50Ω
Frequency
Ranges: 1KHz, 10KHz, 100KHz, 1000KHz, 8MHz
Best Resolution: 0.01Hz; Input sensitivity: 0.7V AC rms
Accuracy: ±(0.05% + 5d); Max. Input Voltage: 250V
Frequencies to 1Ghz can be read with optional adapter
Secondary display reads: Duty cycle and mS pulse width
RPM
Range: 0 to 99,999; Resolution: 1RPM
Accuracy: ±(0.1% + 5d)
Note: The RPM function is the secondary display of the
frequency measurement and requires the RPM adapter
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Square wave Generator
Amplitude: Approx 3V
Frequencies from 0.500Hz to 5.000KHz may be selected in
15 Steps
Duty Cycle: Variable from 1% to 99%
General Specifications
Operating Temperature: 0 to 50ºC (32 to 122ºF)
Power: 9Volt battery @ 36 Hours of operation
Size: 7.5" (H) x 3.54" (W) x 1.45" (D)
Weight: 1.43 lbs
Auto Power-Off: 30 minutes or the timer value.
Accessories: Instruction manual, Test leads, Holster,
Temperature probe, 9V battery, RS-232 software and cable
50,000 Count Multimeter
6500
K 50,000 count and 50 segment bar graph backlit display
K Basic DC accuracy is ±0.03%
K RS232 interface with software and cable
K dBm measurement with 4Ω to 1200Ω reference resistances
K AC and (AC+DC) TRUE RMS measurement
K Measures frequency, Duty cycle and Capacitance
K Cat III 1000V
K Max/Min and Relative measurements
K Auto power off and backlit display
6500
SPECIFICATIONS
DC mV
Ranges: 50mV, 500mV; Best Resolution: 1µV
Accuracy: ±(0.03% + 6d); Input Impedance: 1GΩ
DC Volts
Ranges: 5V, 50V, 500V, 1000V; Best Resolution: 100µV
Accuracy: ±(0.03% + 6d); Max. Input Voltage: 1000V DC
Input Impedance: 10MΩ
AC mV
Ranges: 50mV, 500mV; Best Resolution: 1µV
AC mV Accuracy:
40Hz to 1Khz: ±(0.5% + 40d), 1KHz to 10KHz: ±(1.0% + 40d),
10KHz to 20KHz: ±(2.5% + 40d)
Input Impedance: 1GΩ
AC Volts
Ranges: 5V, 50V, 500V, 1000V; Best Resolution: 100µV
AC Volts Accuracy (5V to 500V ranges):
40Hz to 1KHz: ±(0.5% +40d), 1KHz to 10KHz: ±(1.0% + 40d),
10KHz to 20KHz: ±(2.5% + 40d)
Max. Input Voltage: 1000V DC or AC peak
Input Impedance: 10MΩ
DC µA:
Ranges: 500µA, 5000µA; Best Resolution: 10.0nA
Accuracy: ±(0.15% + 1d)
Overload Protection: 0.5A/250V fuse
DC mA
Ranges: 50mA, 500mA; Best Resolution: 1.0µA
Accuracy: ±(0.15% + 10d)
Overload Protection: 0.5A/250V fuse
DC A
Ranges: 5A, 10A; Best Resolution: 100µA
Accuracy: ±(0.5% + 10d)
Overload Protection: 10A/250V fuse
Diode Test
Range: 2.5V; Resolution: 0.1mV
Accuracy: ±(1.0% + 5d); Test Current: Approx. 0.7mA
AC µA
Ranges: 500µA, 5000µA; Best Resolution: 10.0nA
Accuracy: ±(0.75% + 10d) 40Hz to 1KHz
Overload Protection: 0.5A/250V fuse
AC mA
Ranges: 50mA, 500mA; Best Resolution: 1.0µA
Accuracy: ±(0.75% + 20d) 40Hz to 1KHz
Overload Protection: 0.5A/250V fuse
AC A
Ranges: 5A, 10A; Best Resolution: 100µA
Accuracy:
40Hz to 1KHz 5A: ±(0.75% + 20d)
40Hz to 1KHz 10A: ±(0.75% + 20d)
Overload Protection: 10A/250V fuse
Capacitance
Ranges: 50nF, 500nF, 5µF, 50µF, 500µF, 5000µF
Best Resolution: 10pF; Accuracy: ±(1.0% + 5d)
Maximum Input Volts: 250V
Frequency
Ranges: 5Hz to 200KHz; Best Resolution: 0.001Hz
Accuracy: ±(0.006% + 4d)
Input Sensitivities (Range/Sensitivity):
(500mV / 0.1V), (5V / 0.5V), (50V / 4V), (500V / 40V),
(1000V / 400V), (5000µA / 1000µA), (500mA / 100mA)
Duty Cycle
Range: 0 to 90%; Resolution: 0.01%
Accuracy: ±10%
Resistance
Ranges: 500Ω, 5KΩ, 50KΩ, 500KΩ, 5MΩ, 50MΩ
Best Resolution: 10.0mΩ; Accuracy: ±(0.1% + 5d)
Max. Input Voltage: 250V
Continuity Buzzer
Buzzer Will Sound: < 60Ω resistance
Logic Frequency
Sensitivity: +2V to +5V Square wave
Accuracy: ±(0.006% + 4d)
Frequency Range: 5Hz to 2MHz
General Specifications
Operating Temperature:
0 to 30ºC (32 to 86ºF) @ 80% Relative Humidity
31 to 51ºC (87 to 124ºF) @ 50% Relative Humidity
Power: (6) AAA Batteries
Size: 7.9" (H) x 3.94" (W) x 1.57" (D)
Weight: 1.23 lbs
Accessories: Manual, test leads, RS232 cable and
software CD
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
23
304
305
304
AC/DC Clamp-On Meter
A480B
3-1/2 Digit
AC/DC Mini Clamp-On Meter
305 3-3/4 Digit True RMS
A480B 300 Amp
AC/DC Clamp-On Meter
Analog Clamp-On Meter
K Measures AC/DC current to 1000A
K Manual ranging
K Measures AC/DC current to 1000A
K True RMS AC Measurements
K Measures Volts, Amps and Ohms
K 1.37" Jaw opening for cramped
K Auto/Manual ranging
K Frequency counter
wiring locations
K Overload protection with indicator
K Data hold, Fused input
K 40 segment analog bar graph
K 2-1/4" Jaw opening
reading for closer examination at safe
location
K Meets IEC-1010 Category III 600V
K Meets IEC-1010 Category III 600V
K Temperature measurement
K Meter Lock Switch freezes measured
K For use in plant maintenance, HVAC,
electrical installation, motor repair
and similar applications
Safety Standards
safety standards
CE
CE
304
305
CE
A480B
SPECIFICATIONS
[ 304 ]
[ 305 ]
[ A480B ]
Volts AC
Ranges: 500V
Best Resolution: 0.1V
Accuracy: ±(1.0% + 3d), 40Hz to 400Hz
Maximum Input: 500V DC or AC RMS
Volts AC
Ranges: 4V, 40V, 400V, 600V; Accuracy: ±(0.5% Rdg + 5d)
Maximum Input: 750V RMS; Input Impedance: 10MΩ
Volts AC
Ranges: 150V, 300V and 750V
Sensitivity: 2KΩ/V
Accuracy: ±3% FS
Volts DC
Ranges: 200V
Best Resolution: 0.1V
Accuracy: ±(0.8% + 1d)
Maximum Input: 500V DC or AC RMS
Resistance
Ranges: 200Ω
Best Resolution: 0.1Ω
Accuracy: ±(1.2% + 5d)
Maximum Input: 400V or AC RMS
DC/AC Current
Ranges: 200 and 1000A
Best Resolution: 0.1A
Accuracy: ±(1.2% + 5d)
Maximum Input: 1200A DC or AC RMS
General Specifications
Power: 9V battery
Size: 7.1" (H) × 1.9" (W) × 1.4" (D)
Weight: 20 oz
Accessories: Manual, Test leads, Carrying case
24
Volts DC
Ranges: 400mV, 4V, 40V, 400V, 600V
Best Resolution: 100µV; Accuracy: ±(0.5% Rgd + 3d)
Maximum Input: 1000V DC or 750V RMS
Input Impedance: 10MΩ
Resistance
Ranges: 400Ω , 4KΩ , 40KΩ , 400KΩ , 4MΩ , 40MΩ
Best Resolution: 0.1Ω; Accuracy: ±(1.5% + 5d)
Maximum Input: 250V DC or AC RMS
DC/AC Current
Ranges: 400 and 1000A; Best Resolution: 0.1A
Accuracy: ±(2.0% Rdg + 5d)
Maximum Input: 1000A DC or AC RMS
Continuity Buzzer
Buzzer will sound < 40Ω resistance
Frequency
Ranges: 100Hz, 1KHz, 10KHz, 100KHz, 1MHz
Best Resolution: 0.01Hz; Accuracy: ±(0.2% Rdg + 2d)
Maximum Input: 250V DC or AC RMS
General Specifications
Operating Temperature: 0 to 40°C (32 to 104°F),
relative humidity 0 to 80% Rdg
Size: 9.6” (H) × 3.4” (W) × 1.7” (D); Jaw Size: 2.25"
Weight: 15 oz; Power: (2) 1.5V AAA batteries;
Accessories: Manual, Test leads, Carrying case
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Volts DC
Range: 60V
Sensitivity: 8KΩ/V
Accuracy: ±3% FS
AC Current
Ranges: 6A, 60A, 300A
Accuracy: ±5% FS
Temperature
Ranges: -20 to 150°C
Accuracy: ±5% FS
Resistance
Ranges: X1Ω and X10Ω
Mid Scale: 30Ω and 300Ω
Accuracy: ±4% of FS
General Specifications
Size: 9.0" (H) × 3.0" (W) × 1.5" (D)
Jaw Size: 2.5"
Weight: 1 lb
Power: (1) 1.5 V AA battery
Accessories: Manual, Test leads, Carrying case
2 MHz Sweep Function Generator
K
Sine, Square, Ramp and Pulse wave forms
K
Built-in 2MHz frequency counter
K
7 frequency ranges with 100:1 frequency control
K
Less than 0.5% sine wave distortion
K
Variable symmetry
K
Sweep time from 20ms to 2 seconds
K
TTL sync output
B8011
CE
B8011
SPECIFICATIONS
Output Characteristics
Frequency Range: 0.02Hz to 2MHz
Ranges: 7
Output level:
High: 10Volts into 50Ω
Low: 1V P-P into 50Ω
Waveforms: Sine, Square, Ramp, Pulse
Impedance: 50Ω
DC offset: 5.0V in to 50Ω
Sine Wave
Distortion: <0.5% from 5Hz to 20KHz
Triangle
Linearity: >99% to 100KHz
Square wave
Rise/Fall Time: <100ns (into 50)
Frequency Counter
Modes: Internal and external
Measuring Range: 0.005Khz to 2000KHz
No. of digits: 4
Accuracy: 0.01% + 1count
Sensitivity: 100mV rms
Input Impedance: 1MΩ + 25pF
Max input V: 150V DC and AC rms
General Specifications
Line Voltage: 120/220V, 50/60Hz
Dimensions: 3.1" (H) x 9.0" (W) x 10.4" (D)
Weight: 4.4 lbs
Operating Temperature: 0 to 45ºC (32 to 113ºF)
Accessories: Manual, Line cord, BNC cable
Pulse
Duty Cycles: 20:80 to 80:20 may be obtained
Sweep
Types: Linear
Sweep time: 2ms to 20s
Sweep width: variable to 100:1
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
25
B8400
4 MHz Sweep Function Generator
K
Wide 0.004Hz to 4MHz Frequency range
K
CW/Triggered and Gated modes
K
Sweep output and VCG input
K
1000:1 linear sweep and 10,000:1 frequency log sweep widths
K
Settable Sweep Start and Stop Frequencies
K
Low Distortion sinewave
B8400
SPECIFICATIONS
Frequency Characteristics
Frequency Range: 0.004Hz to 4MHz in 7 ranges
Ranges: x1, x10x, x100, x1K, x10k, x100k, x1M
Dial Accuracy: 5% of full scale
Output Characteristics
Waveforms: Sine, Square, Triangle, TTL Pulse
High output:
Amplitude: 15mV to 10V (into 50Ω)
DC Offset: 0 to ±5 into 50Ω
Impedance: 50Ω
Attenuator: 30dB variable
Low Output:
Amplitude:0 to 1V (into 50Ω)
DC Offset: 0 to ±0.5 (into 50Ω)
Impedance: 50Ω
Attenuator: 30dB variable
Sine Wave
Frequency Range: 0.004Hz to 4MHz
Flatness:
±2.0 % (0.004Hz to 400KHz)
±10% (400KHz to 4MHz)
Harmonic Distortion:
< 0.5 % on the 1K and 10K range
1% on the x1, x10, x 100 and x100K ranges
25dBc on the x1M range
Square Wave
Frequency Range: 0.004Hz to 4MHz
Rise/Fall Time: < 50ns into 50Ω (High output terminals)
Symmetry: ±1% to 100KHz, ±5% to 4MHz
26
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Triangle
Linearity: > 99% to 200KHz
Operating modes
CW, Triggered, Gated, Sweep, Manually Triggered
Trigger/Gate input level: TTL
Trigger/Gate Frequency Range: to 4MHz Max.
Trigger/gate minimum pulse width: < 50ns
Sweep
Type: Linear and Log
Sweep Time: 30ms to 60 seconds continuously variable
Sweep width: 1:1,000 linear; 1:10,000 log continuously
variable. Sweep start and stop frequencies may be set with the
Freq dial and the Freq. Stop control.
Outputs
Sync: TTL level
GCV: output proportional to the selected frequency, 0 to -5V
Sweep: 4V P-P; Impedance: 600Ω
VCG Input
Input Voltage: 0 to ±4V P-P will cause a 1:1,000 frequency
change (linear) and 1:10,000 (Log)
Input Impedance: 2KΩ
General Specifications
Operating Temperature: 0 to 50°C (32 to 120°F)
Dimensions: 3.5" (H) x 11.4" (W) x 10.6" (D)
Weight: 5 lbs
AC line Voltage: 120/220V, 50/60Hz
Accessories: Manual, Line cord, BNC cable
10MHz Generators
B8110 10MHz Sweep Function Generator
B8110
B1990
B1990 10MHz Pulse Generator
K
Wide 0.01Hz to 10MHz frequency range
K
1Hz to 10MHz Frequency Range
K
Log/Lin sweep
K
Variable Pulse width and Delay
K
Burst /gate and triggered modes
K
Manual and External triggering
K
Output may be FM modulated using the VCG input.
K
Output amplitude to 5V p-p (into 50Ω)
K
Low distortion Sine wave
K
May be crystal controlled
K
Sweep start and Stop capability
B8110
B1990
SPECIFICATIONS
[ B8110 ]
Frequency Characteristics
Frequency Range: 0.01Hz to 10MHz
Output Characteristics
Waveforms: Sine, Square Pulse, Triangle and ramp
Impedance: 50Ω
Attenuator: 20dB, 40 dB, 60dB and 20 dB variable
Amplitude: 0 to ±10 Volts in to an open circuit
DC Offset: 0 to ±10 V in to an open circuit (0 to ±5 into 50Ω)
Sine Wave
Frequency Range: 0.01Hz to 10MHz
Flatness: ±3.5% from 0.01Hz to 100KHz
±10% 100KHz to 10MHz
Harmonic Distortion: < 0.5 % from 10 Hz to 40KHz
Symmetry: 20:80 to 80:20
Square Wave
Frequency Range: 0.01Hz to 10MHz
Rise/Fall Time: < 25ns into 50Ω
Pulse
Frequency Range: 0.01Hz to 10MHz; Rise Time: < 10ns
Duty Cycle: adjustable symmetry control from 20:80 to 80:20
Ramp and Triangle
Linearity: > 99%
Operating Modes
CW, Triggered, Gated, Burst Sweep
Trigger/Gate input level: TTL
Trigger/Gate Frequency Range: DC to 100KHz
Burst time: 1ms to 10s
Sweep
Type: Linear and Log
Sweep Time: 1ms to 2s in 2 ranges, continuously variable
Sweep width: 1:100 continuously variable. Sweep start
frequency may be set with the SET/MOD control.
Modulation
Type: AM
Input: External Through the MOD input connector
Frequency: DC to 1MHz
Modulation Range: 0 to 100%
Modulation Voltage: 0 to 5V P-P
Type: FM:
Input: External through the VCG input
Tuning Range: 1000:1 with an input of 0 to -5V
Frequency Characteristics
Frequency Range:
Internal: 1Hz to 10MHz (100ns to 1s) in 7 ranges
Xtal: 10Hz to 10MHz
Output Characteristics
Amplitude: 0.5 to 5V p-p (into 50Ω)
Impedance: 50Ω
Input Impedance: 2KΩ
Rise Time: 10ns (into 50Ω)
Output Polarity: Positive or Negative
Pulse Width Range: 50ns to 5ms in 5 ranges
Pulse Delay Range: 0 to 2µs in
Outputs
Sync: TTL level
GCV: output proportional to the selected frequency, 0 to -5V
Sweep: 0 to -5V; Sweep/Burst Gate: TTL level
General Specifications
Operating Temperature: 0 to 50°C (32 to 120°F)
Dimensions: 4.3" (H) x 12.5" (W) x 14" (D)
Weight: 15 lbs
AC line Voltage: 120/220V, 50/60Hz
Accessories: Manual, line cord, BNC cable
[ B1990 ]
Trigger
Trigger modes:
Internal, Ext (+ or - edge triggered), Xtal and Manual
Trigger out:
Width: 20ns; Amplitude: 5V; Impedance: 50Ω
External Trigger in:
Input V range: +1.0V to -1.0V P-P (sine or square wave)
Repetition Rates: 10Hz to 10MHz; Impedance: 2KΩ
General Specifications
Operating Temperature: 0 to 40°C (32 to 104°F)
at less than 85% humidty
Stability: 0.1% per hour after warm up
Dimensions: 4.3" (H) x 11.4" (W) x 10.2" (D)
Weight: 6.4 lbs
AC line Voltage: 120/220V, 50/60Hz
Accessories: Manual, line cord, BNC cable
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
27
B821
20 MHz Sweep Function Generator
K
Sweep Function Generator and Frequency Counter
K
Sine, Square, Triangle, Ramp, Pulse, Skewed Sine and TTL Square Waveforms
K
0.2Hz to 20MHz Frequency Output (Sine wave)
K
Built-in 8 digit 3.0GHz Frequency Counter
K
Internal and External linear Sweep control
K
Variable Symmetry for generating Sawtooth (Ramp), Skewed Sine and Pulse Waveforms
K
Variable DC Offset control
K
Variable Output level control and 20 dB attenuator
B821
SPECIFICATIONS
[ B821 ]
Output Characteristics
Frequency Range:
Sine wave: 0.2Hz to 20MHz
Square & Triangle wave: 0.2Hz to 10MHz
Range selection in 8 ranges (1,10,100,1K,10K,100K,1M,10M)
Output Level:
20 ±1 Vp-p in open circuit
10 ±0.5 Vp-p into 50Ω Load
Waveforms:
Sine, Square, Triangle, Ramp, Pulse, Sawtooth, TTL Leveled
Square
Attenuator: 20dB fixed and continuously variable (20dB)
Impedance: 50Ω ±0.5%
Frequency Accuracy: ±5% of full scale
Waveform Characteristics
Sine Wave:
Flatness: ±3dB to 20MHz
Distortion: Less than 1.5 % at 0.2Hz to 100KHz
Duty error: Less than 10% in 50:50
Square Wave:
Rise and Fall Time: < 25ns at 10MHz
Triangle Wave: Linearity: More than 99% at 0.2Hz to 100KHz
TTL Output:
Rise and Fall Time: < 25ns at 10MHz
TTL Level: H $ 2.4V, L # 0.4V
Symmetry Variation:
Sine & Square; 80:20 to 20:80 at 0.2Hz to 2MHz
Triangle; 80:20 to 20:80 at 0.2Hz to 1MHz
28
Sweep Function Characteristics
Mode: Linear
Width: Variable from 1:1 to 10:1
Rate: 0.5Hz to 50Hz (20ms to 2s)
External VCF Input:
Input Voltage: 0 to 10V
Input Impedance: Approx. 10KΩ
Frequency Counter Characteristics
Display: 8 digits Green LED, Overflow, Gate time,
MHz, KHz, Hz
Frequency Range:
Input A: 0.1Hz to 100MHz
Input C: 80MHz to 3.0GHz
Accuracy: ±Timebase Error ±1 count
Low pass Filter: -3 dB, 100KHz
Timebase: 10MHz TCO, 1 ppm
Input Sensitivity:
Input A (30mVrms): 0.1Hz to 80MHz
Input A (70mVrms): 80MHz to 100MHz
Input C (20mVrms): 80MHz to 2.0GHz
Input C (70mVrms): 2.0GHz to 3.0GHz with RG58 cable
Input C (40mVrms): 2.0GHz to 3.0GHz with RG400 cable
Max. Input Voltage:
Input A: 35Vp-p
Input C: 3Vrms
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
General Specifications
Power Requirements: 115/230VAC ±10%, 48 to 66Hz
Operating Temperature:
0 to 40°C (Accuracy specified at 23°C ±5°C),
32 to 104°F (Accuracy specified at 73°F ±9°F)
Size: 3.5" (H) x 9.5" (W) x 11.0" (D)
Weight: 6.6 lbs
Supplied Accessories: Manual, Line cord, BNC cable
Programmable 2.4GHz
Universal Counter
C3100
K Accurate frequency measurements to 2.4GHz
K Measures Frequency, Period, Duty Cycle, RPM, Frequency ratio, Difference
frequency, Time interval and Totalize
K Nine measurement functions
K Plots trend graph on LCD display
K Compare, Relative Error and Min/Max functions
K Standard RS-232 with optional GPIB interface
K Eight setup screens may be saved and retrieved from memory
K Software for controlling, displaying data and data logging
K Operates on all line voltages from 85V to 270V without any changes
C3100
SPECIFICATIONS
Frequency Measurement
Freq A
Ranges: DC coupled: 0 to 120MHz
AC coupled: 10Hz to 120MHz
Resolution: 0.00001Hz @ 200Hz
Gate Times: 50ms to 10s (20 settings)
Accuracy: ±2PPM; Coupling: AC or DC
Trigger Level: ±1.8V in a scale from -99 to +99
Freq B
Ranges: DC coupled: 0 to 120MHz
AC coupled: 10Hz to 120MHz
Resolution: 0.00001Hz @ 200Hz
Gate Times: 50ms to 10s (20 settings)
Accuracy: ±2PPM; Coupling: AC or DC
Trigger Level: ±1.8V in a scale from -99 to +99
Freq C
Ranges: 100MHz to 2.4GHz
Resolution: 100Hz @ 500MHz
Gate Times: 50ms to 10s (20 settings)
Accuracy: ±2PPM + 1 count
Coupling: AC only
Trigger Level: Auto
Totalize
Input: CH A
Frequency Range: DC to 10MHz
Count Capacity: 0 to 99,999,999 counts
Resolution: 1 count
Accuracy: ±1 count
Time Interval (AàB)
Input: CH A and CH B
Range: 0.5µs to 200,000µs
Minimum Pulse Width: 250ns
Resolution: 1µs
Accuracy: ±1 count + timebase accuracy
Channel C
Frequency Range: 100MHz to 2.4GHz (usable to 2.7GHz)
Sensitivity: 25mV RMS (100MHz to 2.4GHz)
Maximum Input voltage: 5V DC or AC peak
Attenuator: None
Input Impedance: 50Ω
Ratio (A/B)
Inputs: CH A and CH B
Range: CH A: 10MHz to 150MHz
CH B: 0.1MHz to 10MHz
Resolution (0.000001)
Reference Timebase Oscillator
Standard Frequency: 10MHz, 4.194304MHz
Frequency Stability: ±5.0 PPM Max
Aging Rate: ±1.0 PPM Max/Yr
Temperature: -30 to +60°C (-22 to +140°F)
Storage Temperature Range: -40 to +85°C (-40 to +185°F)
Duty Cycle
Input: CH A
Measurement Range: 0.01% to 99.99%
Frequency Range: 0 to 100KHz
RPM
Input: CH A
Measurement Range: 0 to 600,000 RPM
Minimum Pulse Width: 250ns
Resolution: 0.1 RPM
Input Characteristics
Channel A & B
Frequency Range: 0 to 120MHz
Sensitivity: 25mV
Input Impedance: 1MΩ + 35µF capacitance
Attenuator: X1, X10
Maximum Input Volts: 250V DC or AC peak
Software
The supplied software is a Windows®-based program, which
runs under Windows 95/98/ME/XP/2000. It allows the user to set
the Instrument Parameters from the PC via the RS-232 interface
and provides time stamped data logging for all functions.
General Specifications
Display: 128 × 64 pixel super twist LCD
Line Voltage: AC input Volts: 85 to 270V AC ±10%
Line Frequency: 48Hz to 66Hz
Power Consumption: 15W
Operating Temperature: 0 to 40°C (32 to 104°F)
Size: 3.3” (H) x 11.6” (W) × 11.0” (D); Weight: 4.4 lbs
Supplied Accessories: Manual, Line cord, BNC cable,
Software, RS-232 cable
Optional Accessories: GPIB (installed)
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
29
B3110
3.0GHz Universal Counter
K High accuracy frequency measurements to 3.0GHz
K Measures Frequency, Period, Time Interval, Ratio and Totalize
K High Stability TXCO
K Variable Trigger level on Inputs A and B
K Large Bright 8 digit LED display With gate time and function indicators
K Low Pass filter and X10 attenuator
B3110
SPECIFICATIONS
Frequency Measurement
Input A
Ranges
Low Range:
DC coupled: 0.1Hz to 10MHz
AC coupled: 10Hz to 100MHz
High Range: 10MHz to 100MHz
Best Resolution:
Low Range: 0.1Hz
High Range: 1Hz
Gate Times: 0.01s to 10s in 4 decades
Accuracy: ±(Time base error + 1 count)
Input B: (Used only for Ratio A/B and Time interval)
Range:
DC coupled: 0.1 to 10MHz
AC coupled: 10Hz to 100MHz
Freq C
Range: 100MHz to 3.0GHz
Best Resolution: 10Hz
Gate Times: 0.0128s, 0.128s, 1.28s and 12.8s
Accuracy: ±(Time base error + 1 count)
Totalize
Input: A
Frequency range: DC to 10MHz
Count Capacity: 0 to 99,999,999 counts
Resolution: 1 count
Minimum Pulse width: 250ns
Accuracy: ±1 count
Time Interval: (AàB)
Inputs: A and B
30
Range: 0.5µs to 200ms (5Hz to 2MHz)
Minimum Pulse Width: 250ns
Best Resolution: 100ns
Multipliers: x1, x10, 100, 1000
Accuracy: ±(Time base error + 1 count) ±Input A
Trigger error ±Multiplier
Ratio: (A/B)
Inputs: A and B
Range:
CHA: 10MHz to 100MHz
CHB: 0.1Hz to 10MHz
Resolution: Input B/(input A x multiplier)
Accuracy: ±Input B trigger error/Input B x Gate time)
±1 count
Period: Input A
Range: 0.5µs to 200ms (5Hz to 2MHz)
Minimum pulse width: 250ns
Best Resolution: 100ps
Accuracy: ±(Time base error + 1 count) ±Input A Trigger
error
Input Characteristics:
Inputs A & B
Sensitivity: #25mV
Input Impedance: 1MΩ + 40pF capacitance
Attenuator: x1, x10
Coupling: AC and DC
Low pass filter: To approx. 100KHz
Slope: Plus or Minus
Trigger level: ±350mV variable and 0V fixed
Maximum input volts: 250V DC or AC peak
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Input C
Frequency Range: 100MHz to 3.0GHz
Sensitivity:
#15mV (100MHz to 800MHz)
#60mV (800MHz to 3.0 GHz)
Maximum input voltage: 3V rms
Attenuator: None
Input Impedance: 50Ω
Coupling: AC
Time Base
Type: TXCO
Frequency: 10.00000MHz
Stability: ±3.0 PPM per week
Time base output: 500mV p-p into 50Ω
General Specifications
AC input Volts: 100V/120V/220V/240V
Line Frequency: 50/60Hz
Power consumption: 20VA
Operating temperature: 0 to 40°C (32 to 104°F)
Size: 4.0" (H) x 10.0" (W) x 11.0" (D)
Weight: 5.25 lbs
Accessories: Manual, Line cord, BNC cable
1.3GHz Multi-Function Counter
B8118
K High accuracy frequency measurements to 1.3 GHz
K Frequency Resolution to 0.1Hz
K High input sensitivity
K Large Bright 8 digit LED display With gate time and function indicators
K X10 attenuator
K Measures Frequency, Period and Totalise
B8118
SPECIFICATIONS
Frequency Measurement
Input A
Range: 10 Hz to 100MHz
Resolutions: 0.1Hz,
Gate Times: 0.01s to 10s in 4 decades
Accuracy: ±(Time base error + 1 count)
Input B
Range: 100MHz to 1.3GHz
Best Resolution: 10Hz
Gate Times: 0.01s to 10s in 4 decades
Accuracy: ±(Time base error + 1 count)
Totalize: Input A
Frequency range: DC to 10MHz
Count Capacity: 0 to 99,999,999 counts
Resolution: 1 count
Minimum Pulse width: 250ns
Accuracy: ±1 count
Period: Input A
Range: 1.0 µs to 100ms (10Hz to 1MHz)
Minimum pulse width: 250nS
Resolutions: 100ps, 1ns, 10ns, 100ns
Accuracy: ±(Time base error + 1 count) + Trigger error
Input Characteristics
Input A
Sensitivity: 50 mV (10Hz to 100Hz)
20mV (100Hz to 100MHz)
Input Impedance: 1MΩ + 30pF capacitance
Attenuator: x1, x10
Coupling: AC
Maximum input volts: 30V rms
Input B
Sensitivity: 15mV (100MHz to 1000MHz)
40mV (1000MHz to 1300MHz)
Input Impedance: 50Ω
Coupling: AC
Max input Volts: 7V
Time Base
Frequency: 10.00000MHz
Stability: ±3 PPM per week
General Specifications
AC input Volts: 120V or 220V
Line Frequency: 50/60Hz
Operating temperature: 0 to 40°C (32 to 104°F)
Size: 4.0" (H) x 10.0" (W) x 11.0" (D)
Weight: 3.75 lbs
Accessories: Line cord, Manual, BNC cable
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
31
Z9218
High Accuracy, Wide Range LCR Meter
with LCD Readout
K 0.02% Basic accuracy
K Wide measurement Ranges for Capacitors, Resistors and Inductors
K Menus and parameters are displayed on an easy to read 320x 240 Graphics LCD with backlight
K Measurement Rates to 12 times per second
K 500 Test Frequencies from 12Hz to 100KHz
K Open and short-circuit compensation for accurate zeroing
K Binning and Pass/Fail operation
K Measurement averaging from 1 to 255
K Optional GPIB and handler interface
K LCD displays measured values, Q/D, Absolute g and %g
CE
Z9218
SPECIFICATIONS
Measured Components
L(Inductance),C(Capacitance), R(Resistance)
Measurement Circuit configurations:
Series and Parallel
Measurements
Resistance:
Measured Parameter: R+Q
Measurement Ranges:
R: 10µΩ to 100MΩ
Q: 0.0001 to 9,999
Inductance:
Measured Parameter: L+Q
Measurement Range:
L: 0.01µH to 99,999 H
Q: 0.0001 to 9,999
Capacitance:
Measured Parameters: C+D and C+R
Measurement Range:
C: 0.00001pF to 99,999µF
D: 0.0001 to 9,999
R: 0.0001Ω to 9,999KΩ
32
Display
Display Type: 320x 240 Graphics LCD W/Backlight
Display value: 5 digit LCR and a 4 digit Q/D measurement
Parameters Displayed: Measured values, absolute g
and %g
Test Environment
Test Frequencies: 500 test frequencies from
12Hz to 100KHz
Test Voltage: 5mV to 1.275V in 5mV increments
Test Voltage Accuracy: ±(5% + 5mV) (1 + 001 x F2)
Measurement rates:
Slow 1 Meas/sec
Medium: 5 Meas/sec
Fast: 12 Meas/sec
Measurement Delay: from 1ms to 99,999ms
Ranging: Auto or Manual.
DC Bias: Internal: 2V, External: 0 to 60V
Triggering: Continuous or Triggered
Zeroing correction: Open and short circuit
Averaging: 1 to 255 Avgs
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Measurement Accuracy
Basic accuracy: ± >0.02% at 23°C ±5°C (73°F ±9°F),
(See user manual for all accuracy conditions)
Remote Operation: GPIB and Handler (Optional)
General Specifications
AC Voltage input: 120 or 220 Volts
Frequency: 50/60 Hz
Power Consumption: 20Watts (Max)
Operating Temperature:
0 to 50°C (32 to 122°F) at # 85% Relative Humidity
Size: 5.5" (H) x 15" (W) x 18" (D)
Weight: 17.6 lbs
Accessories: Manual, Line Cord, Kelvin leads with bag,
GPIB Handler (Optional)
High Accuracy, Wide Range LCR Meter
320 x 240 pixel LCD for displaying the
component value along with its Q or D
value in a absolute, g or %g display.
Test Frequency, Test voltage,
Circuit mode, Number of averages, Binning
and the Soft Keys for selecting these
parameters are also displayed.
The function Keys select the
operating parameters displayed on
the LCD. Trigger mode,
Measurement rate, Component
value in absolute, g or %g are
some of the functions that may be
selected.
EXT Bias key when in the C+D or C+R
mode allows an external bias voltage
up to 60V to be applied to the
capacitor under test. This is normally
used to stabilize a High value
Electrolytic for an accurate reading.
Z9218
Selects the type of component and
parameter to be measured.
R&Q, L&Q, C&D, C&R or Auto
may be selected.
Numeric keyboard for entering Test
Frequency, Voltage values, Number of
averages, Cal Data Measurement delay
and Nominal values.
Four wire input: 2 inputs supply the drive
signal and 2 inputs are for input sensing,
thereby removing errors caused by lead
length.
The start key initiates a
measurement in the
triggered mode.
These two keys are used to adjust the
contrast of the LCD display.
SCREENS
C/R MEASUREMENT SCREEN
L/Q MEASUREMENT SCREEN
C/R g% MEASUREMENT SCREEN
SHORT CIRCUIT CALIBRATION SCREEN
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
33
Z8200
LCR Meter
K Measures L, C, R, |Z|, Q and D
K Displays component value, Q or D, Delta, or Delta%
K 5 digit display for component value and Q/D
K Auto ranging or Range hold
K Built-in comparator with 4 bin-sorting function
K Open and short circuit calibration for accurate zeroing
K Series and parallel equivalent circuit modes
K Three test frequencies
K Warning alarm for pass or fail binning
K Easy to use
Z8200
SPECIFICATIONS
Measurements
Components:
L (Inductance)
C (Capacitance)
R (Resistance)
Z (Impedance)
Circuit Configuration: Series and Parallel
Parameters Displayed: Measured values, absolute Delta and
Delta %
Resistance/Impedance
Measured Parameter: R + Q and |Z|
Measurement Range:
R: 1mΩ to 999.99MΩ
Q: 0.0001 to 99999
Inductance
Measured Parameter: L + Q
Measurement Range:
L: 1µH to 999.99H (100Hz & 120Hz)
L: 0.1µH to 999.99 (1KHz)
Q: 0.0001 to 99999
34
Capacitance
Measured Parameter: C + D
Measurement Range:
C: 1pF to 999.99µF
D: 0.0001 to 99999
Test Environment
Test Frequency: 100Hz, 120Hz, 1KHz
Test Voltage: 0.3V RMS
Drive Voltage Accuracy: ±10%
Measurement Rate: 2 Measurements/Sec
Ranging: Auto or Hold
Measurement Accuracy
Basic Accuracy: ±0.3% @ 23°C ±5°C (73°F ±9°F)
(See user manual for detailed accuracy conditions)
Zero Input Correction: Open and short circuit
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
General Specifications
Power Requirement: AC Voltage Input: 120/220V
Frequency: 50/60Hz
Power Consumption: 10W (Max)
Operating Temperature:
0 to 40°C (32 to 104°F) at # 85% Relative Humidity
Size: 4.3” (H) x 10.6” (W) x 10.2” (D)
Weight: 5.5 lbs
Accessories: Manual, Line cord, Test leads with Kelvin clips
CM109
Capacitance/Inductance Meter
CM110
CL200
CM109 3-1/2 Digit LCD
Capacitance Meter
CM110 3-1/2 Digit 2000
Count Capacitance Meter
K Measures capacitance to 20mF
K Zero adjust for compensating stray
K Six capacitance ranges and four
K Zero adjust
capacitance
K Large easy to read 3-1/2 digits,
K High accuracy measurement
K Fused input
K Large LCD display
K Rugged case design
K Inputs for clip leads and lead
insertion
CL200 3-1/2 Digit 2000
Count L/C Meter
inductance ranges
2000 count LCD
K 0.5% measurement accuracy
K Fused input
K Automatic zeroing
K 9 measurement ranges
K Three measurement frequencies
K Includes holster
K Low battery indicator
K Fuse protected input
K Includes holster
CM109
CM110
CL200
SPECIFICATIONS
[ CM109 ]
Capacitance
Range: 200pF, 2nF, 20nF, 200nF 2µF, 20µF, 200µF,
2000µF, 20mF
Best Resolution: 0.1pF
Accuracy:
±(0.5% Rdg + 1d): 200pF to 200µF Ranges
±(1% Rdg + 1d): 2000µF Range
±(2% Rdg + 1d): 20mF Range
Test Frequencies:
200pF to 2µF Ranges: 200Hz
20µF Range: 80Hz
200µF to 20mF Ranges: 8Hz
Zero Adjustment Range: ±20pF
Overload Protection: 0.25A/250V fuse
General Specifications
Power: 9V battery
Operating Temperature: 0 to 40°C (32 to 104°F)
with a relative humidity of less than 70%
Size: 5.3” (H) × 2.8” (W) × 1.3” (D)
Weight: 7.5 oz
Supplied Accessories: Manual, Test leads, Battery
[ CM110 ]
[ CL200 ]
Capacitance
Ranges: 200pF, 2nF, 20nF, 200nF, 2µF, 20µF, 200µF,
2000µF, 20000µF
Best Resolution: 0.1pF
Accuracy:
±(0.5% + 1d): 200pF to 200µ ranges
±(1% + 1d): 2000F range
±(2% + 1d): 20mF range
Test Frequencies:
200pF to 2µF ranges: 800Hz
20µF range: 80Hz
200µF to 20,000µF ranges: 8Hz
Zero Adjustment Range: ±20pF
Overload Protection: 0.25A/250V fuse
Capacitance
Ranges: 2nF, 20nF, 200nF, 2µF, 20µF, 200µF
Best Resolution: 1pF
Accuracy:
±(1% + 1d): 2nF to 200nF ranges
±(2% + 1d): 2µ to 200µF ranges
Test Frequencies:
2nF to 2µF ranges: 900Hz
20 µF and 200µF ranges: 80Hz
Measurement Condition: Specifications are measured within
a temperature range of 18°C to 28°C (64°F to 82°F)
General Specifications
Power: 9V Battery
Calibration Interval: 1 year
Operating Temperature: 0 to 40°C (32 to 104°F)
with a relative humidity of less than 70%
Size: 7.4” (H) x 3.7” (W) x 1.3” (D)
Weight: 7.5 oz
Supplied Accessories: Manual, Test leads, Holster
Measurement Condition: Specifications are measured within
a temperature Range of 18 to 28°C (64 to 82°F)
Inductance
Ranges: 2mH, 20mH, 200mH, 2H
Best Resolution: 1µH
Accuracy:
±(2% + 1d), 2mH to 200mH range
±(5% + 1d), 2H range
Test Frequency: 900Hz
General Specifications
Power: 9V NEDA Battery
Calibration Interval: 1 year
Operating Temperature: 0 to 40°C (32 to 104°F)
with a relative humidity of less than 70%
Size: 7.4” (H) x 3.7” (W) x 1.3” (D)
Weight: 7.5 oz
Supplied Accessories: Manual, Test leads, Holster
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
35
Hand-Held 2GHz
RF Signal Strength Analyzer
3201
K Hand-Held and battery operated
K 100KHz to 2060MHz measurement range
K 12.5 Ch/sec scan rate
K Built-in 2GHz frequency counter
K High sensitivity (-117 dBm max)
K Detects Wide band and Narrow band FM, AM and Single Sideband
Signals
K Phase lock loop for precise frequency tuning
K RS-232 interface (includes software and cable)
K Up to 160 channels may be scanned and displayed
K Audio output with built-in speaker
K Detachable antenna included
K Back-lit display
K All functions are menu selected
K Instrument setups & display data may be stored in memory
K Hard copy printer output of spectrum and bar graph
displays
3201
SPECIFICATIONS
Frequency
Frequency Range: 100KHz to 2060MHz
Frequency Step: 5KHz to 9995KHz in multiples of 5KHz or
6.25KHz
Ref. Oscillator Accuracy: ±3 PPM
Frequency Marker Accuracy: ±25 PPM
Frequency Measurements: Narrow Band FM, Wide Band FM,
AM and Single side band
Input
Input Impedance: 50Ω
Maximum Input Volts: 5V RMS (+27dBm)
Measurement Units: dBmV, dBµV, dBm
Attenuation: 0dB or -10dB internal; 0dB to 60dB with external
Attenuator
Narrow Band FM
Level Measurement Range:
-117dBm to -67dBm (1MHz to 2060MHz)
Resolution: ±0.5dB; Accuracy: ±3dB
Bandwidth: 12.5KHz
Wide Band FM, AM & SSB
Level Measurement Range:
-108dBm to -58dBm (10MHz to 2060MHz)
Resolution: ±0.5dB; Accuracy: ±3dB
Bandwidth:
Wide band FM: Approx. 180KHz
AM and SSB: Approx. 2.4KHz
BFO Frequency Range: ±1.5KHz
Reception Sensitivity: 0 to 6dBµV EMF with supplied antenna
Antenna Reception S/N Ratio: N-FM: 10 dB; W-FM: 12 dB
36
Display
Display Modes: Spectrum, Bar graph, Frequency counter
Spectrum Display: Displays 160 channels
Bar Graph Displays: Multi channel (2, 5, 10, 20, 40, 80, 160
bar graphs per display), Single Channel and 2 Channel
difference
Sweep Modes: Single, Normal, Free run
Spurious Signals: (internally generated) -35dBc for W-FM
-45dBc for N-FM (typical below full scale signal level)
Scan Mode
Mode: Manual, Channel (memory scan) and Search scan
Scan Rate: 12.5 Ch/sec
Memory
Data Memory: Stores 10 displays of up to 160 CH per display
Setup Memory: Stores 10 setups for each scan mode
Frequency Counter
Bandwidth: 9MHz to 2060MHz
Resolution: 1KHz
Accuracy: 50PPM ±1 count
Input Impedance: 50Ω
Max Input Volts: 5V RMS
Response Time: 0.512 sec
Input Sensitivity:
9MHz to 2060MHz: 120mV
20MHz to 1500MHz: 50mV
2MHz to 2060MHz: 500mV
Data Memory: Stores 10 Readings
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Miscellaneous
LCD: 192 x 192 Pixels, Light green
Back Light: LED. Back light will shut off 5 seconds after the last
key depression
Interfaces: Std RS-232 interface with female 8 pin mini Din
connector. Baud Rates of 1200, 2400, 4800 or 9600 BPS are
menu selected. The software supplied is a Windows®-based
program, which runs under Windows 95/98/ME/XP/2000.
Auto Power Off: 5, 10, 20 or 30 minutes after the last key
depression (user selected).
Audio Output :120mW into 8Ω Speaker
Power Requirements: (6) AA NiCd or Alkaline Batteries, 12 volt
car adapter or 11V to 16V 500 mA Max AC to DC adapter
General Specifications
Operating Temperature: 0°C to 40°C (32 to 104°F)
Relative Humidity: 35% to 85%
Storage Temperature: -10 to 50°C (14 to 122°F)
Size: 9.5" (H) x 4.0" (W) x 1.8" (D)
Weight: 1.4 lbs
Supplied Accessories: Manual, (6) 1.5V AA NiCd Batteries,
Detachable 9" whip antenna, RS-232 Cable and Software,
Carrying case, Earphone, Carrying strap, Vehicle power adapter,
AC/DC adapter
Hand-Held 2GHz
RF Signal Strength Analyzer
X10 Attenuator
Extends input range
Antenna or Coax Input
Volume Control
3201
Earphone Jack
For noisy environment operations
Input for Frequency Counter
Built-in 9MHz to 2060MHz
Belt Clip
Hands-free transport
Audio Speaker
LCD Display
Bright, easy-to-read, 192 x 192
pixels, up to 160 channels
Dial Knob
Fast one-hand selection of menu
items and freq. marker
Function Keys
Fast entry of preset or
custom values and functions
Numeric Input Keys (+ or -)
For entering
8 digit freq. values
DC Input Jack
Accepts AC/DC adaptor; car
adaptors; and battery charger
(included)
On-Off Power
Auto-power off saves batteries
Frequency keys
Marker or Menu edit
LCD Key
Varies contrast for easy viewing
RS-232C Connector
Printer or computer connection
(software included)
DISPLAY
Function Mode
Scan Mode
Title Name
Marker Frequency
Ref. Level
Marker Level
Attenuantor Value
Marker
Center Frequency
Span Frequency
Step Frequency
Menu for Funtion Keys
Sequency Level
Sweep Mode
Reception Mode
SPECTRUM ANALYZER DISPLAY
CHANNEL EDIT MODE
Up to 1600 channels may be stored in
any order, then scanned and identified
by 9-digit freq. and 5-letter title. Useful
for Cable TV, Cellular phone, and other
field applications where repetitive
measurements need to be made.
TWO CHANNEL DIFFERENCE MODE
This Mode displays 2 carrier levels and
their difference. A key application verifies
that a TV or Cable channel’s video and
audio carriers are within specifications.
BAR-GRAPH DISPLAY
This feature makes level readings easy
and “cleans up” each frequency
(compared to a spectrum display).
Patterns may be readily seen, for
example: this display of computer monitor
radiation.
SPECTRUM DISPLAY
This Mode scans and displays 160
channels. Squelch level may be set above
or below carrier level in order to pause
scan and detect the signal. Detection
modes are AM, NFM, WFM and SSB.
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
37
Hand-Held 2.9GHz
RF Signal Strength Analyzer
3290
K Hand-Held and battery operated
K 100KHz to 2900MHz measurement range
K 125 Ch/sec scan rate
K Built-in 2.9GHz frequency counter
K High sensitivity (-117 dBm max)
K Detects Wide band and Narrow band FM, AM and Single Sideband
Signals
K Phase lock loop for precise frequency tuning
K RS-232 interface (includes software and cable)
K Up to 160 channels may be scanned and displayed
K Audio output with built-in speaker
K Detachable antenna included
K Back-lit display
K All functions are menu selected
K Instrument setups & display data may be stored in memory
K Hard copy printer output of spectrum and bar graph
displays
K Ideal for IEEE 802.11 applications, Cellular
Telephones, RF paging systems, Indoor repeaters,
Surveillance applications
3290
SPECIFICATIONS
Frequency
Frequency Range: 100KHz to 2900MHz
Frequency Step: 5KHz to 9995KHz in multiples of 5KHz or
6.25KHz
Ref. Oscillator Accuracy: ±3 PPM
Frequency Marker Accuracy: ±25 PPM
Frequency Measurements: Narrow Band FM, Wide Band FM,
AM and Single side band
Input
Input Impedance: 50Ω
Maximum Input Volts: 5V RMS (+27dBm)
Measurement Units: dBmV, dBµV, dBm
Attenuation: 0dB or -10dB internal; 0dB to 60dB with external
Attenuator
Narrow Band FM
Level Measurement Range:
-117dBm to -67dBm (300MHz to 1800MHz)
-107dBm to -67dBm (1MHz to 300MHz and 1800MHz to
2900MHz)
Resolution: ±0.5dB; Accuracy: ±3dB
Bandwidth: 12.5KHz
Wide Band FM, AM & SSB
Level Measurement Range:
-107dBm to -57dBm (300MHz to 1800MHz)
-97dBm to -57dBm (10MHz to 300MHz and 1800MHz to
2900MHz)
Resolution: ±0.5dB; Accuracy: ±3dB
38
Bandwidth:
Wide band FM: Approx. 180KHz
AM and SSB: Approx. 2.4KHz
BFO Frequency Range: ±1.5KHz
Reception Sensitivity: 0 to 6dBµV EMF with supplied antenna
Antenna Reception S/N Ratio: N-FM: 10 dB; W-FM: 12 dB
Display
Display Modes: Spectrum, Bar graph, Frequency counter
Spectrum Display: Displays 160 channels
Bar Graph Displays: Multi channel (2, 5, 10, 20, 40, 80, 160
bar graphs per display), Single Channel and 2 Channel
difference
Sweep Modes: Single, Normal, Free run
Spurious Signals: (internally generated) -35dBc for W-FM
-45dBc for N-FM (typical below full scale signal level)
Scan Mode
Mode: Manual, Channel (memory scan) and Search scan
Scan Rate: 125 Ch/sec
Memory
Data Memory: Stores 10 displays of up to 160 CH per display
Setup Memory: Stores 10 setups for each scan mode
Frequency Counter
Bandwidth: 9MHz to 2900MHz
Resolution: 1KHz
Accuracy: 50PPM ±1 count
Input Impedance: 50Ω
Max Input Volts: 5V RMS
Response Time: 0.512 sec
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Input Sensitivity:
9MHz to 2060MHz: 120mV
20MHz to 1500MHz: 50mV
2MHz to 2800MHz: 500mV
2800MHz to 2900MHz: 750mV
Data Memory: Stores 10 Readings
Miscellaneous
LCD: 192 x 192 Pixels, Light green
Back Light: LED. Back light will shut off 5 seconds after the last
key depression
Interfaces: Std RS-232 interface with female 8 pin mini Din
connector. Baud Rates of 1200, 2400, 4800 or 9600 BPS are
menu selected. The software supplied is a Windows®-based
program, which runs under Windows 95/98/ME/XP/2000.
Auto Power Off: 5, 10, 20 or 30 minutes after the last key
depression (user selected).
Audio Output :120mW into 8Ω Speaker
Power Requirements: (6) AA NiCd or Alkaline Batteries, 12 volt
car adapter or 11V to 16V 500 mA Max AC to DC adapter
General Specifications
Operating Temperature: 0°C to 40°C (32 to 104°F)
Relative Humidity: 35% to 85%
Storage Temperature: -10 to 50°C (14 to 122°F)
Size: 9.5" (H) x 4.0" (W) x 1.8" (D)
Weight: 1.4 lbs
Supplied Accessories: Manual, (6) 1.5V AA NiCd Batteries,
Detachable 9" whip antenna, RS-232 Cable and Software,
Carrying case, Earphone, Carrying strap, Vehicle power adapter,
AC/DC adapter, Holster
Hand-Held 2.9GHz
RF Signal Strength Analyzer
X10 Attenuator
Extends input range
Antenna or Coax Input
Volume Control
3290
Earphone Jack
For noisy environment operations
Input for Frequency Counter
Built-in 9MHz to 2900MHz
Belt Clip
Hands-free transport
Audio Speaker
LCD Display
Bright, easy-to-read, 192 x 192
pixels, up to 160 channels
Function Keys
Fast entry of preset or
custom values and functions
Dial Knob
Fast one-hand selection of menu
items and freq. marker
Numeric Input Keys (+ or -)
For entering
8 digit freq. values
DC Input Jack
Accepts AC/DC adaptor; car
adaptors; and battery charger
(included)
On-Off Power
Auto-power off saves batteries
Frequency keys
Marker or Menu edit
LCD Key
Varies contrast for easy viewing
RS-232C Connector
Printer or computer connection
(software included)
DISPLAY
Function Mode
Scan Mode
Title Name
Marker Frequency
Ref. Level
Marker Level
Attenuantor Value
Marker
Center Frequency
Span Frequency
Step Frequency
Menu for Funtion Keys
Sequency Level
Sweep Mode
Reception Mode
SPECTRUM ANALYZER DISPLAY
CHANNEL EDIT MODE
Up to 1600 channels may be stored in
any order, then scanned and identified
by 9-digit freq. and 5-letter title. Useful
for Cable TV, Cellular phone, and other
field applications where repetitive
measurements need to be made.
TWO CHANNEL DIFFERENCE MODE
This Mode displays 2 carrier levels and
their difference. A key application verifies
that a TV or Cable channel’s video and
audio carriers are within specifications.
BAR-GRAPH DISPLAY
This feature makes level readings easy
and “cleans up” each frequency
(compared to a spectrum display).
Patterns may be readily seen, for
example: this display of computer monitor
radiation.
SPECTRUM DISPLAY
This Mode scans and displays 160
channels. Squelch level may be set above
or below carrier level in order to pause
scan and detect the signal. Detection
modes are AM, NFM, WFM and SSB.
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
39
B1240
Synthesized AM/FM
Signal Generator
K
10 KHz to 1040KHz frequency range
K
AM, PM and FM modulation
K
-127dBm to +6dBm output level
K
Self Test and Calibration capabilities
K
25W reverse power protection
K
100 location memory for storing Frequency, modulation and output level data
K
Optional GPIB interface
B1240
SPECIFICATIONS
Frequency:
Range: 10KHz to 1040MHz
Display Resolution:
10Hz (10KHz to 520MHz), 20Hz (520MHz to 1040MHz)
Accuracy: ±1.5 x 10-6 after 20 minutes of warm up
Output Characteristics:
Output level Range: -127dBm to + 6dBm
Display Resolution: 0.1dB
Accuracy: ±1dB (> -10dBm), ±2dB (< -10dBm)
Amplitude Flatness:
< 0.5dB (10KHz to 1040KHz, -10dBm to +6dBm)
Output impedance: 50Ω
Amplitude Units: dBm and dBµ
Output Protection: 25W of reverse power
Spectral Purity:
Spurious:
Better than -35dB at carrier frequency < 62.5MHz and 0dBm
Better than -25dB at carrier frequency > 62.5MHz and 0dBm
Residual Modulation: FM: 7Hz, AM: 0.05%
Modulation
FM:
Deviation:
0 to 100KHz (1Mz to 1040MHz)
Carrier Freq. x 10% (below 1MHz)
Resolution:
10Hz (0 to 10KHz deviation)
100Hz (10KHz to 100KHz deviation)
40
Accuracy: ±5% for 1KHz or 400Hz modulation
Frequency Response: ±0.5dB (50Hz to 50KHz)
Distortion: < 2% THD (1KHz Mod., Max deviation and
Carrier Freq. > 250KHz)
PM:
Range: 0 to 10 Radians
Resolution: 0.01 Radians
Frequency Response: ±1dB (10KHz to 10KHz)
Deviation Accuracy: ±5% at 1KHz Modulation
AM:
Range: 0 to 99%
Resolution: 0.5%
Accuracy: better than ±4% of depth setting + 1% at 1KHz
Frequency Response: ±0.5% (50Hz to 50KHz)
Envelope Distortion: < 3% THD (at 70% mod and 1KHz)
Modulation Oscillator: Frequency: 1KHz and 400Hz
External modulation Input:
Range: 10Hz to 50KHz
Input Level: 0.9V to 1.1V RMS (With Modulation ALC)
Input Impedance: 100KΩ (Approx.)
Memory:
Locations 0 to 19 store Frequency, Modulation and Output level
data; Locations 20 to 99 store Frequency data only;
3 independent memories for storing output level data.
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Display:
Carrier Frequency: 9-digit LED
Modulation: 3-digit LED
Output Level: 4 -digit LED
Memory Location: 2-digit LED
General Specifications
Input Power: 110/220V
Frequency: 50/60
Size: 4.7" (H) x 17" (W) x 17.7" (D)
Weight: 26.5 lbs
Standard Accessories:
Operation manual, Line cord and Type N cable
Optional Accessories:
GBIB interface
Synthesized AM/FM
Signal Generator
1
2
14 15
3
16
1. Power On/off.
2. Increases5or decreases6the
% mod or Mod Frequency by a
preset value. In the second
function selects 3.5KHz or 22.5
KHz FM deviation.
3. Displays % Modulation in AM
and Frequency Deviation in FM.
4. Selects 400Hz or 1KHz
modulation frequencies. In the 2nd
function selects 75KHz deviation or
30% AM modulation.
5. Increments or decrements the
memory address.
6. Displays the Memory Address.
4
5 6
17
18
19
7. Displays the RF Output
Frequency.
8. Function cursor keys
The outer 2 keys selected the
display to be changed; the inner 2
keys select the digit in the selected
display to be changed.
9. The Delta Frequency is used to
generate a new output frequency
by adding or subtracting the delta
value to the current frequency.
10. +/- keys determine if the Delta
frequency is added or subtracted to
the current frequency.
11. Turns the output on or off. In
the second function selects the dB
units.
12. Displays the RF Output Level.
7
20
8
9 10
11
21
22
23
12
B1240
13
24
13. These keys are used to store
19. Selects if data is being stored
14. When pressed, an External
20. Keypad
preset RF output levels in memory
and recall them when needed.
in or recalled from the displayed
memory.
Reference frequency will be used.
15. Modulation On or Off key.
Enter values for the RF Frequency,
output level, Modulation or memory
display when selected.
16. The Input connector for the
21. Rotary knob
external modulation signal when
External Modulation is selected.
The Modulation output signal is
present at this connector when
internal modulation is selected.
Used also for entering Frequency,
output level, Modulation or memory
values in the selected display.
22. Frequency step keys
Increases5or decreases6the
frequency by a Preset value.
17. When this key is press, the
input-modulating signal is kept at a
constant level. (0.9V to 1.1V)
23. These keys increase5or
decrease6the output level by a
Preset value.
18. 2nd Function Key, Some keys
on the front are dual function,
pressing this key enables the
second function.
24. 'N' type RF 50Ω output
connector.
PANELS
STD FREQ
INPUT
REMOCON
DC 5V
STD FREQ
ADJ
Power Cable
Connector
Fuse
Line Selector
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
41
SL100
B850
Special Purpose Instruments
Audio Products
SL100 Sound Level Meter
B850 Audio Generator
K ANSI & IEC 651 Type 2 standards
K Wide 10Hz to 1MHz Frequency range
K 3-1/2 digit LCD display
K Low distortion Sine wave and Square wave output
K A&C frequency weighting
K Lightweight, Rugged construction
K 0.1dB resolution
K Frequency setting via large frequency dial
K Maximum hold function
K Ideal for classroom or audio bench
K Internal calibration check
K Fast and slow response
K Analog output jack
SL100
B850
SPECIFICATIONS
[ SL100 ]
Measurement Ranges
Frequency: 31.5Hz to 8KHz
Decibel:
A Lo: Weighting: 35 to 100dB
A Hi: Weighting: 65 to 130dB
C Lo: Weighting: 35 to 100dB
C Hi: Weighting: 65 to 130dB
Best Resolution: 0.1dB
Accuracy: ±2dB
Dynamic Range: 65dB
Input: Condenser Microphone
Time Weighting: Slow or Fast
Maximum Hold Decay: < 1dB/3min
Analog Output:
AC Conditioned: 0.7V RMS, corresponding to each range step
Output Impedance: 600Ω
DC Conditioned: 10mV/dB
Output Impedance: 100Ω
General Specifications
Operating Temperature: 0 to 50ºC (32 to 122ºF)
at relative humidity of less than 80%
Power: 9V battery for 100 hours life with alkaline battery
Size: 9.5" (H) × 2.7" (W) × 1.0" (D)
Weight: 7.6 oz
Supplied Accessories: Manual, battery, Adjustment
screwdriver, Carrying case
42
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
[ B850 ]
Output Characteristics
Frequency Range: 10Hz to 1MHz in 5 ranges
Frequency Accuracy:
10Hz to 1MHz: ±5%
100Hz to 100KHz: ±3%
Amplitude: > 20V P-P open circuit; > 10V P-P into 600Ω
Output Impedance: 600Ω
Output Attenuation: 0dB, 20dB, 40dB steps and fine
adjustment attenuator control
Sine Wave Characteristics
Distortion:
< 0.05% from 500Hz to 50KHz
< 0.5% from 50Hz to 500KHz
Square Wave Output
Frequency Range: 10Hz to 100KHz
Output Voltage: > 15V P-P
Rise Time: < 500ns
External Sync Input
Input Impedance: Approx. 10KΩ
Max. Input Voltage: 10V RMS
General Specifications
Power Requirements: 115/230V ±10%
Frequency: 48Hz to 66Hz
Power Consumption: 3VA
Size: 6.0" (H) × 10.0" (W) × 5.0" (D)
Weight: 5.5 lbs
Supplied Accessories: Manual, Line cord, Test leads
Special Purpose Instrument
Digital Insulation Testers
DI2001 Cat. III Insulation Tester
DI2001
DI4000 Insulation Tester
K Measures insulation resistance to 2GΩ
K Measures insulation resistance to 2GΩ
K 250V, 500V and 1000V test voltages
K Measures AC volts
K Meets IEC 1010-1, Category III-600V
K Data hold and backlight
safety standards
DI4000
K 3-1/2 digits, 3200 count LCD
K Data and Max hold
K Designed to IEC-1557-2 standards
K 3-1/2 digit, 2000 count LCD
K Rugged case and lightweight
K Continuity buzzer
K 125V, 250V and 1000V test voltages
DI2001
DI4000
SPECIFICATIONS
[ DI2001 ]
DC Voltage
Range: 0 to 1000V
Resolution: 1V
Accuracy: ±(0.5% Rdg + 1d)
AC Voltage
Ranges: 0 to 750V
Resolution: 1V
Accuracy: ±(0.8% Rdg + 4d)
Mega Ohms
Ranges:
0 to 250MΩ @ 250V
0 to 250MΩ @ 500V
0 to 2000MΩ @ 1000V
Resolution:
0.1MΩ (250MΩ Range)
1.0MΩ (2000MΩ Range)
Accuracy: ±(3% + 5d)
Display: 2000 Count, 3-1/2 Digit
General Specifications
Power: (8) 1.5V AA Batteries
Operating Temperature: 0 to 40°C (32 to 104°F)
at a relative humidity of < 80%
Size: 6.3" (H) × 3.8" (W) × 2.0" (D)
Weight: 17 oz
Supplied Accessories: Manual, Test probe, Leads, Batteries
[ DI4000 ]
AC Voltage
Ranges: 0 to 600V
Resolution: 1V; Accuracy: ±(2.5% Rdg)
Input Impedance: 20MΩ
Max. Input: 600V
Insulation Measurement
Effective Measuring Resistance:
20MΩ @ 125V; 50MΩ @ 250V; 2000MΩ @ 1000V
Rated Measurement Current: Approx. 1mA +20% - 0%
Short Circuit Current: < 2mA
Minimum Measurable Resistance:
20MΩ Range: 0.125MΩ
50MΩ Range: 0.250MΩ
1000MΩ Range: 1.0 MΩ
Accuracy :
125V: 0.02Ω to 10MΩ: < ±5%
500V: 0.1MΩ to 50MΩ: < ±5%
1000V: 2MΩ to 1000ΩΩ: < ±5%
125V: 0.1MΩ to 0.03MΩ and 10MΩ to 100MΩ: < ±10%
500V: 0.05MΩ to 0.1MΩ and 50MΩ to 100MΩ: < ±10%
1000V: 1MΩ to 2MΩ and 1000MΩ to 2000MΩ: < ±10%
General Specifications
Power: (6) 1.5V AA Batteries
Operating Temperature: 0 to 40°C (32 to 104°F)
at a relative humidity of < 80%
Size: 4.1” (H) x 7.0” (W) x 2.1” (D); Weight: 13 oz
Supplied Accessories: Manual, Test Probe, Lead with Case,
6 AA Batteries
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
43
Accessories
PP80
PP150
DC to 60 MHz, X1/X10 Probes
Max.Input: 600V P-P
DC to 100MHz, X10 Probes.
Input Impedance:
9MΩ resistance and 14pF Capacitance.
Max Input: 600V P-P
TP25
TP-25: Temp. probe for model A480B
TP35
'K' type temp. probe for models
TM1300K, D910F, D981, A421, 506,
608, 610, B4000
PROBES & Etc.
Test TL101
Leads: TL102
TL206
TL250
TL501
TL505
A413, A410B, A800, A801
D901, A403
305, 307
A480B, D640AB, D1200D, BT407
B845, D910F, D980, D981, B4000, B4100, S2401, S2405,
TM1300K, 304, 505, 506, A802, 608, 610
A421, A450
TP111 Universal K Type Immersion Probe
Temp Range: -40°F to 1562°F, -40°C to 850°C
TP112 Universal K Type Surface Probe
Temp Range: -40°F to 950°F, -40°C to 510°C
[ TL102 ]
[ TL206 ]
[ TL250 ]
[ TL501 ]
[ TL505 ]
[ TL101 ]
Temp Range: -40°F to 500°F, -40°C to 250°C
CASES & HOLSTERS
Meter CB25A
Carrying CB35D
Cases: CB50A
CB50D
CB506
CB77D
TP113 Universal K Type Air Probe
DI4000, A421
D910F, D981, D980, A802, CM110, CL200, 2700
A450, A803
FC250
505, 506, 608, 610
CM109, D930A, TM1300K
TP115 Universal K Type General Purpose Probe
Temp Range: -40°F to 1562°F, -40°C to 850°C
44
Protek Test & Measurement
45 Smith Street, Englewood, NJ 07631 Tel: 201-818-7711 Fax: 201-760-9888
Website: www.protektest.com Email: [email protected]
Accessories
SALES
& CONTACT
Protek Test and Measurement
45 Smith Street, Englewood, NJ 07631
Tel: 201-818-7711 Fax: 201-760-9888
E-Mail: [email protected]
www.protektest.com
WARRANTY
Protek T & M Limited Warranty
Protek T & M products are warranted against defects in workmanship and materials to the user for a period of
2 years from the date of purchase (90 days for models priced less than $75.00). All warranty claims must be
sent in to an authorized repair depot, transportation prepaid, and must be accompanied by a copy of the sales
invoice, if a warranty. Protek T & M reserves the right to repair or replace all such defective products. All
repaired or replaced units will be returned transportation charges prepaid. Products subjected to physical or
electrical abuse, or if used in an unprescribed manner, are not covered by this warranty. This limited warranty
does not apply to batteries or fuses.
Copyright © Protek Test & Measurement
Protek Test and Measurement
45 Smith Street
Englewood, NJ 07631
TEL: 201-818-7711
FAX: 201-760-9888
www.protektest.com
Excellence in Peformance and Value
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Protek:
CB-25A TL-250 TL-206 TP-25 TL-102 TL-505 TL-101 CB-50A CB-50D CB-77D CB-35D TP112 TP113
TP111 TP115
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement