Roller Grill 400 CFG (CN667) Owner Manual
ROLLER GRILL 400 CFG (CN667) is a high-performance gas crepe maker designed for professional use. With its powerful 3600W burner and enameled cast iron plate, it ensures even heat distribution and precise temperature control for perfectly cooked crepes, pancakes, and other delicacies. The built-in safety features, including a thermocouple and flame failure device, guarantee safe operation.
Advertisement
Advertisement
INSTRUCTIONS FOR USE AND INSTALLATION
GAS CREPE MACHINE
CFG 400
Made in France
December 2011
11
GAS CREPE MACHINE
CFG 400
Nomenclature
Spare parts
CFG 400
CFG 400
Rep
6
7
4
5
8
9
1
2
3
Code
B02050
E01016
E02019
E02016
E02217
67056
67052SE
A13018
A14077
F05017
Qty
1
1
1
1
3
1
1
1
1
1
Pièce
Disque émaillé 400
Brûleur
Injecteur BP (100)
Injecteur GN (145)
Rampe complète
Support brûleur
Ceinture
Pied
Bouton
Râteau en bois
Spare part
Enamelled cast iron plate 400
Burner
Injector BP (100)
Injector GN (145)
Main supply assembly
Burner holder
Casing
Foot
Knob
Wooden scraper
10
Congratulations for the acquisition of this upmarket appliance made in France. You chose an appliance which alloys the best technical qualities with a big userfriendliness. We wish you the biggest contentment
1. SECURITY INSTRUCTIONS
Please respect these instructions scrupulously to avoid any risk of fire, scald or other wounds and damage. During the use of this appliance, fundamental circumspection of security must always be noticed, such as:
- Take into account the instructions to be systematically kept with the appliance.
- Install the appliance always in instructions respect. A 10 cm distance minimum with the partition or the wall is necessary.
- This appliance is marked out for outside use or inside use in a well ventilated room or under a cooker hood.
- Protect the appliance from direct light of the sun, frost and humidity.
- Never leave the appliance within the reach of children or disabled persons without surveillance.
- Never move the appliance when it is working or when the surfaces of cooking are still hot.
- Do not touch the hot surfaces of the appliance. The temperature of the hot surfaces can be very important when the appliance is working. Always use handles and control knobs.
- Do not use the appliance for other functions than determined use.
- Do not leave the pipe or hose (purchased separately from a specialised shop) in the contact of hot surfaces.
- The appliance should not be used close to combustible materials.
- During use, look after not to obstruct hearings of aeration of the appliance.
- Do not bend or clip the pipe or hose
- Entrust compensations only to a skilled person.
- Use only spare parts of origin.
- At the end of cooking, before cleaning the appliance, do not forget to disconnect the gas inlet.
2. CONTENTS OF CARDBOARD PACKAGING
Device: a crepe machine
Accessories: - A wooden rake
- A set of natural gas injectors
- The present note
See exploded view for CFG 400 at the end of the document.
3
3. CONFORMITY OF USE
Use the device only to cook crepes, pancakes, buckwheat cakes...
4. WAY OF FUNCTIONING
This crepe machine is a strong cooktop in enamelled cast iron. The strong thickness of the plate and its specific drawing ensure an excellent homogeneity and a stability of the temperature. The plate’s smooth surface provides direct heat transfer to the food being cooked, without heat loss at the centre as in the periphery thanks to starshaped burner that covers the entire cooking surface.
To turn on and preheat the plate, just switch on the burner by pressing on the power control knob (n°1 on picture) opposite the high flame position for a few seconds. Use a gas lighter or a long matchstick by holding it near the burner and keeping the knob pressed (n°1 on picture) for a few seconds. Then the burner remains lit, set the machine in desired power.
While cooking, the temperature can be regulated using the control knob (n°1 on picture) from high flame to low flame in order to avoid over-cooking.
There is a double security :
If one of the branches of the burner is turned off by a draft, the star located in the middle of the burner will act as a flame diffuser towards the extinguished branches
(patented system). A safety thermocouple cuts the gas supply if the burner is extinguished. The low flame of the appliance is pre-adjusted in the factory, it must not be changed.
Exclusion clauses of the guarantee
Bad installation and bad maintenance, in particular if they do not respect current regulations or instructions appearing in this user guide.
Cannot benefit from the guarantee the repairs required as a result of false operations, of inappropriate use, of carelessness or of excess loads of the device, as well as those resulting from variations of the power supply, over tension or from defective installations.
The damage due to shocks, bad weather is not flatware by the guarantee. The material travels at the risks of the user; in case of delivery by carrier, the consignee has to have reservations towards the carrier before any delivery of the device.
The guarantee comes to an end in case of intervention, of repair, of modification by no qualified persons, or of use in inappropriate purposes.
1 Control knob
1
4 9
6 CLEANING AND MAINTENANCE
Cut the gas supply.
- Let cool completely the device before any technical intervention or cleaning.
- Clean your crepe machine regularly after each use to avoid phenomenon of calamine coming the cooking of the sugar and from some dough which accumulates very quickly, and creates a film on the plate which harms in the quality of the cooking.
- For cleaning, only use non-abrasive products, clean regularly the external walls of your device with warm water and wash liquid: avoid the abrasive towelling. Rinse your device with a wet sponge. Dry it with a soft cloth
- Never clean the device under a water jet, the infiltrations would risk to damage it in a irreparable way.
- During a prolonged non-use, we recommend you strongly to keep the device shielded from the humidity and to grease the plate.
7. TECHNICAL SPECIFICATIONS
Model
Outside dimensions
Weight
Power
No of burner
CFG 400
400 x 183 mm
15.5 Kg
3 600 W
1
8. GUARANTEE
Conditions of guarantee
The guarantee applicable to any device is the commercial guarantee of the distributor or the retailer. Please contact the store where you bought your device to know the precise conditions.
The guarantee grants no right for damages.
The dispositions which follow are not exclusive of the profit of the legal guarantee planned by articles 1641 and following ones of the Civil code relative to the defects and the latent defects.
8
5. FUNCTIONING / HANDLING a) Installation/Assembly:
- Unpack carefully the machine from its packaging.
- Place it on a plane and heatproof surface.
- Never place the device near a wall or near a partition makes of combustible materials even if it is very well isolated.
- A distance of minimum 10 cm with the partition or the wall is necessary.
b) First starting :
Before the first use, remove the anti-corrosion protection fat with a cleaner and a wet sponge.
During the first use, grease your plate with oil and preheat the crepe machine during about 15 min. Once preheating is finished, set the power on the wished temperature.
First cleaning
Clean the device before the first use. (See 6 Cleaning)
Gas connection
The appliances run on the following gases: Butane G30, Propane G31, Natural gas
G20/G25. The appliances are originally delivered with a Butane/Propane injector corresponding to the category II2E+3+. The connection is made thanks to a thread 3/8.
The heat release rate of the appliance is 3.6 kW
For a use in natural gas, change the injectors. They are delivered in a small plastic bag placed in the package.
Connect the appliance to the gas supply pipe, interposing a stop valve which enables the appliance to be insulated from the rest of the installation.
Check the supply pressure using a manometer when the burner is lit. It must be equal to the indications on the rating plate.
The fresh air flow required for combustion air supply is:
CFG 400 7.2 m3/h
General conditions of installation
The installation and maintenance of the appliance must be carried out in compliance with the statutory texts and good practices in force, mainly:
5
General specifications
For all appliances:
Article GZ Installation with combustible gases and liquefied hydrocarbons.
Then, according to use:
Article CH Heating, ventilation, refrigeration
Air conditioning and domestic hot water steam generation.
Article GC Installation of appliances to be used for catering
Specific provisions for each type of establishment to which the public is admitted
(hospitals, shops, etc…)
Important: Never change the diameter of the injectors.
Gas category table, according to the country of destination of the appliance.
Country of destination
France/Luxembourg
Germany
Austria
Belgium
Sweden, Denmark,
Finland
Spain
Netherlands
Norway
Kingdom/Italy/
Portugal
Poland
Category Gas
II2E+3+
II2E+3B/P
G20/G25
G30/G31
G20/G25
G30/G31
II2E+3B/P G20/G25
II2H3B/P
G30/G31
G20
G30/G31
G30/G31 I3+
I2E
II2H3B/P
II2H3+
II2H3P
G20/G25
G20
G30/G31
G20
G30/G31
G20
G31
II2L3B/P
II2L3P
I3B/P
G25
G30/G31
G25
G31
G30/G31
G20
G30/G31
II2E3P
G31
Pressures
20/25
28-30/37
20/25
50
20
50
20
50
28-30/37
20/25
20
28-30/30
20
28-30/37
20
50
25
28-30/37
25
50
28-30/30
20
28-30/37
37
Diameter of injector
145
100
140
90
140
90
140
90
100
145
145
100
145
100
145
90
145
100
145
90
100
145
100
100
6
Injector N°
Injector n°1
Injector n°2
Injector n°3
Injector n°4
Injector n°5
Injector n°6
Gas Pressures
G30 / G31 Butane/Propane 28-30/37
G30 / G31 Butane/Propane 50
G20 / G25 Natural gas 20-25
G25 Natural gas
G25 Natural gas
G31 Propane
25
20
50
Diameter
100/100
90/100
145/100
145/100
150/100
90/100
Air adjustment
Injectors were conceived to avoid any air adjustments and that whatever the gas you use.
c) Use of device :
Elements of command and display
Command/Display
Set knob
(n°1 on picture)
Function
Switches on the appliance
Controls power (low flame = low power, high flame = high power)
Switching-on
Press the power control knob (n°1 on picture) and turn it opposite the high flame position for a few seconds.
Use a gas lighter or a long matchstick by holding it near the burner
Keep the control knob (n°1 on picture) pressed for some more seconds and release it slowly. Your machine is warming up
Grease the plate before each cooking.
Temperature setting
Once the burner is lit; set the appliance to the desired power by turning the control knob (n°1 on picture).
It is not necessary to leave the device switched on at full power. It is necessary to adapt the temperature to products to be cooked to limit the gas consumption.
Stopping the appliance
Set control knob (n°1 on picture) to 0: the appliance is completely switched-off.
Close the butane or propane cartridge
Clean the appliance. (See 6. Cleaning) d) Breakdown / repair:
In case of breakdown or of damaged part, please call your after-sales service and confide any technical operation to qualified person.
When you contact the after-sales service of your distributor or your store, give him the complete reference of your device (commercial name, type and serial number). This information appears on the visible descriptive plate behind the device.
7

Public link updated
The public link to your chat has been updated.
Advertisement