Stretch DVI
Manual Contents
__________________________________________
Stretch DVITM
Manual Contents
1-0
Welcome! Product Description
1-1
System Requirements for Setup
1-2
Installation
1-3
Self-EDID Programming Procedure
1-4
Troubleshooting, Maintenance, Technical Support
1-5
Product Specifications
1-6
Warranty Information
1-7
Regulatory Statements
1-8
Pictorials
Figure 1 – Schematic Connection Diagram of
Optical DVI Extension Modules
User’s Manual
Figure 2 – Connection of power adapter to the
(For M1-201DA-TR)
Figure 3 – Connection of power adapter to the
transmitter
receiver
1-1
1-3
1-3
Figure 4 – Connection of optical fiber
1-4
Figure 5 – Connection of the transmitter to DVI source
1-4
Figure 6 – Connection of the transmitter to the display
1-4
Figure 7 – Position of EDID-PRGM. button and Self
EDID LED
1- 0 Manual Contents
1-5
Welcome!
System Requirements for Setup
TM
Congratulations on your purchase of the Stretch DVI
M1-201DA-TR
Optical DVI (Digital Visual Interface) Extension Module. This manual contains
information that will assist you in installing and operating the product.

Hardware requirements

You have to have a DVI graphic controller or card having a DVI
port in your PC, SUN or Mac systems. It should support the
maximum graphic resolution feature of displays to be connected.

No special requirements for memory size, CPU speed and
chipsets, if you’ve already properly installed your DVI graphic
controllers or cards.
Product Description
The M1-201DA-TR optical DVI module transmits four (4) optical data, Red,
Green, Blue and clock and can be extended up to 1500 meters (4920ft) over
two LC multi or single-mode fiber at WUXGA (1920x1200) at 60Hz vertical
refresh rate. The EDID (Extended Display Identification Data) in a display can
be read and restored by just plugging once transmitter to the display. This

Software requirements

Self-EDID programming feature makes the installation of M1-201DA-TR
No special restrictions, if you’ve already properly installed your
DVI graphic controller in your OS.
more easy and flexile at any variable resolution display systems. For your
convenience, UXGA EDID would have been done before shipment as a

AC/DC Power Adapter Technical Advisory
default.
Shipping Group

M1-201DA-TR Optical DVI Extension Module: One (1) pair

DC power adapter: Two (2) units

User’s Manual
Option Product: Duplex LC Patch Cord (Single or Multi-mode fiber).

The transmitter (Tx) module of M1-201DA-TR is designed for power
protection circuit from conflict of power supply between the external
DC power adapter and your graphic card through the DVI pin. It offers
an option of whether to use an AC/DC power adapter depending on
power supply capability of the graphic card through the +5V pin, you
are using.
However, the receiver (Rx) module should be supplied by an AC/DC
power adapter.
Note 1: In general, most of laptops or desktop PCs with PCI Express
graphic card require using an AC/DC power adapter for the transmitter
module.
Note 2: If you use laptop or Desktop PC with PCI Express graphic card,
we recommend using 5V power adapter for the transmitter.
Figure 1 – Schematic Connection Diagram of Optical DVI Extension Modules
1-1 Welcome, Product Description
1-2 System Requirements for Setup
Installation
Step 5
Important: Please use the installation procedure below. Improper or no
operation may result if the start-up sequence is not correctly followed.
Connect LC optical fibers between the transmitter and the receiver as shown in
figure 4.
Step 1
Carefully unpack the contents of the shipping group.
Step 2
Plug the 5V power adapter to the power jack of the transmitter. Ensure the
blue LED ON after blinking two times.
Figure 4 – Connection of optical fibers
Note: Both of single-mode and multi-mode fiber are applicable to M1-201DA-TR
up to 500meters. In the case of longer than 500meters, you have to use singlemode fibers.
Step 6
Plug the transmitter to the DVI receptacle of the DVI source such as PC.
Figure 2 – Connection of power adapter to the transmitter
Note: You don’t need to connect the power adapter to the transmitter if the
graphic source provides enough power to operate the transmitter. Please,
refer to AC/DC Power Adapter Technical Advisory on page 1-2.
Figure 5 – Connection of the transmitter to the DVI source
Note: Be recommended NOT to use any intermediate cable or adapter between
them to avoid undesirable performance degradation.
Step 3
Please, check if the maximum resolution of the display is UXGA (1600x1200).
Otherwise, follow the instructions for Self-EDID Programming Procedure on
page 1-5.
Step 7
Plug the receiver to the DVI receptacle of the display.
Step 4
Plug the 5V power adapter to the power jack of the receiver. Ensure the blue
LED ON.
Figure 6 – Connection of the transmitter to the display
Step 8
Make the PC and the display power ON.
Figure 3 – Connection of power adapter to the receiver
1-3 Installation
Note: You can replace any DVI cable into an M1-201DA-TR by following the
Step1 to 7, while all powers of PC and display are ON.
1-4 Installation
Self-EDID Programming Procedure
Troubleshooting
The graphic source equipment generally requires communication of display information
(EDID). Display information (EDID) contains resolution and timing information for your
display.
The display displays only black screen.
M1-201DA-TR supports Self-EDID programming. Self-EDID programming means that
the EDID from the display is stored in the transmitter. You should use Self-EDID
programming feature if the resolution of the display is not UXGA(1600x1200). Follow
these steps to record the EDID of the display into the transmitter unit.
- Ensure that all plugs and jacks used by external power supplies (both
Opticis and others) are firmly connected. Ensure the blue LED ON.
- Ensure that the DVI ports are firmly plugged in to the PC and display.
- Ensure that the transmitter and receiver modules plugged correctly to the
PC and display, respectively.
Note1 : If you know that EDID is not required by the source, Self-EDID
programming is not necessary.
- Check if the PC and display are powered on and properly booted.
Note2 : The default EDID in factory ship-out is programmed in the VESA standard
of UXGA (1600x1200) 60Hz.
- Reset the system by de-plugging and re-plugging the transmitter DVI port or
receiver DVI port, or by de-plugging and re-plugging the power cord plugs of
transmitter and receiver modules.
Step 1
- Re-boot up the system while connecting the optical DVI extension module.
Power on the display.
Screen is distorted or displays noises.
Step 2
Insert the included 5V DC power adapter into the transmitter.
Step 3
Push the EDID PRGM. button of the transmitter with a narrow pin. After fourth
time blinking of Self-EDID LED, it will be turned off.
- Check if the graphic resolution is properly set. Go to the display properties of
Windows and tap the settings.
- Ensure that the resolution sets less than WUXGA (1920x1200) at 60Hz
refresh ratio.
- Reset the system. Disconnect and reconnect the optical DVI cables or 5V
power adapters.
Maintenance
Self-EDID LED
EDID-PRGM. button
Figure 7 – Position of EDID-PRGM. button and Self-EDID LED
Step 4
Connect the transmitter to the display while turned on, not to the PC. The
LED on the transmitter will begin to blink rapidly. Blinking indicates reading the
EDID. LED will be turned OFF after blinking for about 18~20 sec. The monitor
EDID has been recorded.
No special maintenance is required for the optical DVI module and power
adapters. Ensure that the DVI modules and power adapters are stored or
used in a benign environment free from liquid or dirt contamination.
There are no user serviceable parts. Refer all service and repair issues to
Opticis.
Technical Support and Service
Disconnect the transmitter from the display. Then, LED ON again.
For commercial or general product support, contact your reseller. For
technical service, contact Opticis by email [email protected] or visit its
website at www.opticis.com
1-5 Self-EDID Programming Procedure
1-6 Troubleshooting, Maintenance, Technical Support
Step 5
Warranty Information
Product Specifications
1 (One) Year Warranty
M1-201DA-TR Optical DVI Extension Modules


Compliance with DVI standard: Supports DVI1.0, fully
implemented by fiber-optic communication and DDC2B by virtual
DDC.
Extension limit: 1500m (4920feet) for WUXGA (1920x1200) at 60
Hz refresh rate.
Fiber Type
Extension Length at WUXGA
Multi-mode Fiber
500m
Single-mode Fiber
1500m
Opticis warrants this optical DVI extension module to be free from defects in
workmanship and materials, under normal use and service, for a period of
one (1) year from the date of purchase from Opticis or its authorized resellers.
If a product does not work as warranted during the applicable warranty period,
Opticis shall, at its option and expense, repair the defective product or part,
deliver to customer an equivalent product or part to replace the defective item,
or refund to customer the purchase price paid for the defective product.
All products that are replaced will become the property of Opticis.
Replacement products may be new or reconditioned.

Graphic transmission bandwidth: Supports up to WUXGA at
60Hz, or 1.65Gbps bandwidth per graphic channel.
Any replaced or repaired product or part has a ninety (90) day warranty or the
reminder of the initial warranty period, whichever is longer.

Fiber-optic connection: The transmitter and receiver modules of
M1-201DA-TR have two LC receptacles so as to be connected with
one LC duplex single or multi-mode fibers, having 9(8)/125m or
62.5(50)/125m core.
Opticis shall not be responsible for any software, firmware, information, or
memory data of customer contained in, stored on, or integrated with any
products returned to Opticis for repair under warranty or not.

DDC connection: Virtual DDC by Auto EDID programming.

Mechanical specifications of transmitter and receiver modules

Operating temperature: 0°C to 50°C
Opticis shall have no further obligation under the foregoing limited warranty if
the product has been damaged due to abuse, misuse, neglect, accident,
unusual physical or electrical stress, unauthorized modifications, tampering,
alterations, or service other than by Opticis or its authorized agents, causes
other than from ordinary use or failure to properly use the product in the
application for which said product is intended.

Storage temperature: - 30°C to 70°C
Dispose of Old Electrical & Electronic Equipment

Humidity: 0% to 85%


Warranty Limitation and Exclusion
Dimensions: 39mm / 15mm / 69mm (W/H/D)
Environmental Specifications
AC/DC Power Adapter

Power Input: AC 100-240V, 50/60Hz 0.1A

Power Output: +5 V, 1A SMPS DC-power Adapter

Cord DC Jack: Core is 5 V and outer is GND.
1-7 Product Specifications
(Applicable in the European Union and other European countries with separate systems)
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
The recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
1-8 Warranty Information
UL/IEC Statement
This equipment has been tested and found to comply with the limits for
medical devices in IEC 60601-1:1994. These limits are designed to provide
reasonable protection against harmful interference in a typical medical
installation.
This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to other devices in the vicinity. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to other devices, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:









Reorient or relocate the receiving device.
Increase the separation between the equipment.
Connect the equipment into an outlet on a circuit different from that
to which the other device(s) are connected.
Consult the manufacturer or field service technician for help.
Type of protection against electric shock: Class I equipment
Degree of protection against electric shock: Not classified - no applied
parts
Classification according to the degree of protection against ingress of
water as detailed in the current edition of IEC 529: IPX0, ordinary
equipment
This equipment is not suitable for use in the presence of flammable
anesthetics or oxygen
Mode of operation: continuous operation
© 2009 Opticis Co., Ltd. All Rights Reserved
Revision 1.1, .Nov. 26, 2009
Opticis Locations
Headquarters
Opticis Co., Ltd.
#304, Byucksan Technopia, 434-6
Sangdaewon-Dong, Chungwon-Ku,
Sungnam City, Kyungki-Do, 462-716
South Korea
Tel: +82 (31) 737-8033~8
Fax:+82 (31) 737-8079
www.opticis.com
Certification of Eye Safety
This laser product is inside implemented by using 1300/1550nm optical
module, manufactured by Opticis Co., Ltd., which are all certified by
IEC/EN60825-1 referred in Accession Number 07-1334-0217 as classified in
Laser Class1.
For order support, please contact your Distributor or Reseller.
1-9 Regulatory Statements
For technical support, check with the Opticis web site www.opticis.com or
contact [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement