User Manual TPC-1251T-E3/TPC-1551T-E3 Series TPC-1251H
User Manual
TPC-1251T-E3/TPC-1551T-E3
Series
TPC-1251H-E3/TPC-1551H-E3
Series
Industrial Touch Panel Computers with
Intel® Atom™ Processors
Copyright
The documentation and the software included with this product are copyrighted 2014
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This Manual Covers the Following Models:
 TPC-1251T-E3 series
 TPC-1551T-E3 series
 TPC-1251H-E3 series
 TPC-1551H-E3 series
TPC-xx51T/H User Manual
Part No. xxxxxxxxxxxxx
Edition 1
Printed in Taiwan
November 2014
ii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
iii
TPC-xx51T/H User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Technical Support and Assistance
1.
2.
Visit the Advantech web site at http://support.advantech.com where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
TPC-xx51T/H User Manual
iv
Safety Instructions
1.
2.
3.
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
v
TPC-xx51T/H User Manual
Caution! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Attention! Danger d'explosion si la pile est remplacée de façon incorrecte. Remplacez seulement avec le même type ou équivalent recommandé par le fabricant. disposer des piles usagées selon les
instructions du fabricant.
TPC-xx51T/H User Manual
vi
Chapter
1
General Information ............................1
1.1
1.2
Introduction ............................................................................................... 2
Specifications ............................................................................................ 2
1.2.1 System Kernel............................................................................... 2
1.2.2 I/O Ports........................................................................................ 2
1.2.3 O/S support................................................................................... 2
1.2.4 Safety and Environment................................................................ 3
LCD Specifications.................................................................................... 3
Touchscreen Specifications ...................................................................... 4
Power ........................................................................................................ 4
I/O Ports Arrangement .............................................................................. 4
Figure 1.1 I/O Port Arrangement ................................................. 4
Panel Mounting ......................................................................................... 5
Dimensions and Cutout............................................................................. 5
Figure 1.2 TPC-1251T/TPC-1251H Dimensions ........................ 6
Figure 1.3 TPC-1551T/TPC-1551H Dimensions ......................... 7
1.3
1.4
1.5
1.6
1.7
1.8
Chapter
2
System Setup .......................................9
2.1
2.2
2.3
2.4
System Setup.......................................................................................... 10
Figure 2.1 Unpack the Package ................................................ 10
Figure 2.2 Install CFast Memory Card
(Mylar in accessory box can be attached to CFast card
for easy extraction) ................................................... 11
Figure 2.3 Power Connector and Power Lines .......................... 11
Figure 2.4 Power Receptor & Button Pin Assignment ............... 12
2.1.1 Installing the Drivers ................................................................... 12
Transport and Unpacking........................................................................ 13
Panel Mounting ....................................................................................... 13
Cabinet Installation and Earth Grounding setup ..................................... 14
Appendix A
Serial Port Settings ...........................17
A.1
Jumper, Dip switch and Connector location............................................ 18
A.1.1 Top.............................................................................................. 18
A.1.2 Bottom......................................................................................... 18
Jumper setting and Description............................................................... 19
A.2.1 CMOS Clear Function (CN1) ...................................................... 19
Switch Setting ......................................................................................... 19
A.3.1 Termination Resistor Select (SW3)............................................. 20
Connector Pin Definition ......................................................................... 20
A.4.1 SATA connector (CN12) ............................................................. 20
A.4.2 SATA Power connector (CN13) .................................................. 21
A.4.3 Mini PCIE slot (MINIPCIE) .......................................................... 21
A.4.4 CFast slot (CN14) ....................................................................... 22
A.4.5 Power in connector (CN18)......................................................... 22
A.4.6 LAN RJ45 connector (CN7,CN8) ................................................ 23
A.4.7 USB connector (CN10) ............................................................... 24
A.4.8 COM1 RS232 connector (CN15) ................................................ 24
A.4.9 COM2 RS232/422/485 connector (CN16) .................................. 25
A.2
A.3
A.4
Appendix B
Driver Installation and Configuration ..
27
B.1
EC Driver Installation .............................................................................. 28
vii
TPC-xx51T/H User Manual
B.2
B.3
B.4
B.5
B.6
B.7
B.8
B.9
B.10
EC Brightness Control Tool Installation .................................................. 30
EC Watchdog Timer Driver Installation................................................... 32
Intel Graphics Driver Installation ............................................................. 36
Intel Chipset Software Installation Utility Installation............................... 39
Intel® Trusted Execution Engine Driver Installation................................ 41
LAN Driver Installation ............................................................................ 44
Windows 7 USB 3.0 Driver Installation ................................................... 47
Touchscreen Driver Installation .............................................................. 49
Touchscreen Calibration ......................................................................... 52
Appendix C
Windows 8.X BIOS Setup ................. 55
C.1
Windows 8.X BIOS Setup ....................................................................... 56
TPC-xx51T/H User Manual
viii
Chapter
1
1
General Information
1.1 Introduction
The TPC-1251T/TPC-1551T & TPC-1251H/TPC-1551H Touch Panel Computers are
state-of-the-art Human Machine Interfaces featuring 12" & 15" displays with Intel
Atom™ E3827 1.75 GHz Processor
The key features are as follows:




True-flat touch screen
TPC-xx51T series is true-flat touch screen designed with IP66 front protection.
Fanless
By using a low-power processor, the system does not have to rely on fans,
which often are unreliable and causes dust to circulate inside the equipment.
Wide operating temperature
TPC-xx51T/H series support -20 ~ 60°C wide operating temperature solution to
provide flexibility in harsh environments.
Bright Display
The TFT LED LCD display suits industrial demands for clear interfaces. Wide
Operating Temperature & Isolation Protection.
1.2 Specifications
1.2.1 System Kernel






CPU: Intel® Atom™ E3827 1.75 GHz Processor
BIOS: AMI UEFI BIOS
VGA: Integrated in Intel® Atom™ E3827
Ethernet: 10/100/1000Base-T x 2
Watchdog Timer: EC watchdog timer; 1.0 second timeout period
Storage:
CFast slot x 1
2.5" SATA HDD/SSD slot x 1 (optional, accessory TPC-1251T-EHKE required)
1.2.2 I/O Ports




RS-232 x 1, RS-232/422/485 x 1
USB 3.0 x 1
USB 2.0 x 1
Full-size Mini PCIe Card x1
1.2.3 O/S support


Microsoft® Windows
– WES7 32bit/64bit
– WE8S 64bit
– Windows 7 32bit/64bit
– Windows 8 64bit
(see Appendix B, Chapter C for BIOS set up before installing Windows 8.X)
Linux Kernel
TPC-xx51T/H User Manual
2
1.3 LCD Specifications
TPC-1251T-E3 / TPC-1251H-E3 TPC-1251H-E3 / TPC-1551H-E3
Series
Series
Display Type
Size
Maximum Resolution
Maximum Colors
Viewing Angle (CR≥10)
Luminance (cd / m2)
Contrast Ratio
Operating Temperature
Backlight Lifetime
Backlight
Note!
TFT LED LCD
TFT LED LCD
12.1”
15”
1024 x 768 (XGA)
1024 x 768 (XGA)
262K/16.2m
262K/16.7m
160°/140°
160°/140°
600
400
700:1
700:1
-30 ~ 80°C
-30 ~ 80°C
50,000 hours
50,000 hours
LED
LED
There might be several bright or dark pixels on the LCD. This phenomenon is normal in today’s LCD manufacturing. Inspection criteria are following specifications defined by LCD vendor.
3
TPC-xx51T/H User Manual
General Information
Safety
 FCC Class A
 CE certificated
 The front bezel is compliant with IP66 for true flat models and IP65 for the TPCs
with the traditional front bezel
Environment
 Operating Temperature:
– -20 ~ 60°C (-4 ~ 140°F)
 Storage Temperature:
– -30 ~ 70°C (-22 ~ 158°F)
 Humidity: 40°C @ 10~95% relative humidity (non-condensing)
 Vibration:
With CFast: 2 Grms (5~500 Hz)
With HDD: 1 Grms (5 ~ 500 Hz)
(Operating, random vibration)
Chapter 1
1.2.4 Safety and Environment
1.4 Touchscreen Specifications






Touch Type: 5- wire Resistive
Base Glass Construction: Tempered glass
Resolution: 1024 x 1024
Light Transmission: 80% ± 3% (Measured by BYK-Gardner)
Controller: USB Interface
Lifespan: 1 million touches at single point
Note!
Touchscreen ITO maybe crash duo to heavy usage .
1.5 Power

Input Voltage: 24VDC +/- 20% (the fuse will become an open circuit if the input
level exceeds 32 VDC)

Typical: 24 VDC @ 1.9Amp for 12", 1.7Amp for 15"
1.6 I/O Ports Arrangement
The arrangement of the I/O ports is shown in in Figure 1.1
USB 2.0
COM 1: RS-232
LAN
Power Connector
USB 3.0
COM 2: RS-232/RS-422/RS-485
Figure 1.1 I/O Port Arrangement
TPC-xx51T/H User Manual
4
1.
2.
3.
4.
There is a rubber waterproof gasket on the AL front bezel. Make sure the waterproof gasket is in position before installing TPC into the panel opening.
Install the TPC into the panel opening.
Take the clamps and long screws from the accessory box. Hook the clamps to
the holes around the four sides of the bezel. Insert the screws into every clamp
and fasten them. These screws will push the mounting panel and fix the unit.
The suggested mounting panel thickness is less than 6 mm (0.236”).
TPC-1251T-E3 Series
 Weight: 2.5 kg
 Dimensions (W x H x D): 311.8 x 238.0 x 57.2 mm (12.28" x 9.37" x 2.25")
 Cutout: 303 x 229 mm
TPC-1551T-E3 Series
 Weight: 3.9 kg
 Dimensions (W x H x D): 383.2 x 307.3 x 61.1 mm (15.09" x 12.10" x 2.41")
 Cutout: 374.5 x 298.5
TPC-1251H-E3 Series
 Weight: 2.5 kg
 Dimensions (W x H x D): 311.0 x 237 x 54 mm (12.24" x 9.37" x 2.25")
 Cutout: 303 x 229 mm
TPC-1551H-E3 Series
 Weight: 3.9 kg
 Dimensions (W x H x D): 383.0 x 307.0 x 59.0 mm (12.28" x 9.37" x 2.32")
 Cutout: 374.5 x 298.5 mm
5
TPC-xx51T/H User Manual
General Information
1.8 Dimensions and Cutout
Chapter 1
1.7 Panel Mounting
9
30
180
180
9
30
Figure 1.2 TPC-1251T/TPC-1251H Dimensions
TPC-xx51T/H User Manual
6
Chapter 1
115
115
30
Figure 1.3 TPC-1551T/TPC-1551H Dimensions
7
TPC-xx51T/H User Manual
General Information
115
115
30
TPC-xx51T/H User Manual
8
Chapter
2
System Setup
2
2.1 System Setup
You can easily get TPC started by following the below steps.
1. Unpack the TPC package. Check the packing list at the beginning of this manual
to make sure all items have been included.
Figure 2.1 Unpack the Package
TPC-xx51T/H User Manual
10
Install a CFast® card containing the operating system.
Chapter 2
2.
Warning! It is suggested to turn OFF system power as you plug in or pull out the
memory card, even though the CompactFlash memory is hot swappable.
Il est suggéré de désactiver l'alimentation du système que vous branchez ou retirez le carte mémoire, même si la mémoire CompactFlash
est remplaçable à chaud.
3.
Connect the power connector to the 24 VDC power lines. The power lines can
either be of some power adapter or in-house power source.
Figure 2.3 Power Connector and Power Lines
11
TPC-xx51T/H User Manual
System Setup
Figure 2.2 Install CFast Memory Card
(Mylar in accessory box can be attached to CFast card for easy extraction)
Figure 2.4 Power Receptor & Button Pin Assignment
4.
5.
6.
Plug the power lines into the system power receptor.
Supply power to the system
Calibrate the touchscreen.
Note!
If you want to install the touchscreen driver & use the touchscreen utility,
please refer the user manual which is "PenMount 6000 InstallationGuide" in the CD-ROM.
2.1.1 Installing the Drivers
After installing your system software, you will be able to set up the Ethernet, VGA,
and touchscreen functions. All drivers are stored in a CDROM disc entitled “TPC1251T, TPC-1551T, TPC-1251H & TPC-1551H” which can be found in your accessory box.
The various drivers in the CD-ROM disc have their own text files which help users
install the drivers and understand their functions. These files are a very useful supplement to the information in this manual.
Note!
The drivers and utilities used for the TPC-1251T, TPC-1551T, TPC1251H & TPC-1551H panel PCs are subject to change without notice. If
in doubt, check Advantech's website or contact our application engineers for the latest information regarding drivers and utilities.
TPC-xx51T/H User Manual
12
2.3 Panel Mounting
1.
Position the TPC against the panel.
2.
Insert the clamps into the side of the TPC.
13
TPC-xx51T/H User Manual
System Setup
When accepting a delivery, please check the packaging for visible transport damage
and check the delivery for completeness by comparing it with your order. If you notice
any shipping damage or inconsistencies between the contents and your order,
please inform the responsible delivery service immediately.
During transport, the TPC should be protected from excessive mechanical stress. If
the TPC is transported or stored without packaging, shocks, vibrations, pressure and
moisture may impact the unprotected unit. A damaged packaging indicates that
ambient conditions have already had a massive impact on the device. Therefore,
please use the original packaging during transportation and storage.
If the TPC is transported in cold weather or is exposed to extreme variations in temperature, make sure that moisture (condensation) does not build up on or inside the
HMI device. Moisture can result in short-circuits in electrical circuits and damage the
device. To avoid that, please store the TPC in a dry place and bring the TPC to room
temperature before starting it up. If condensation occurs, a delay time of approximately 12 hours must be allowed to make sure the TPC is completely dry before the
TPC is switched on.
Chapter 2
2.2 Transport and Unpacking
3.
Secure the clamp to the panel using the included screws
2.4 Cabinet Installation and Earth Grounding setup
Please follow the following steps to setup TPC-xx51T/TPC-xx51H series, and please
pay attention that Ground pin of TPC-xx51T/TPC-xx51H series should be connected
to earth ground. Under this circumstance, TPC-xx51T/TPC-xx51H series could have
the best performance such as EMI immunity, ESD immunity, Surge immunity and
also system isolation. If TPC-xx51T/TPC-xx51H series is embedded in the cabinet,
TPC-xx51T/TPC-xx51H’s ground, cabinet’s ground and earth ground should all be
connected together.
1. Embed TPC-xx51T/TPC-xx51H series into the cabinet.
Step A: Connect the cabinet to earth ground.
Step B: Embed null TPC-xx51T/TPC-xx51H series into the cabinet without any I/O cable
and power.
TPC-xx51T/H User Manual
14
System wiring
Chapter 2
2.
System Setup
Step A: Connect the cabinet to earth ground.
Step B: Ensure that all cabinet has been grounded together.
Step C: Connect the ground of the power supply to the cabinet.
Step D: Connect the ground pin of TPC-xx51T/TPC-xx51H series to the cabinet.
Step E: Connect the I/O to the controller if needed.
Step F: Connect the V+ and V- of power supply to TPC-xx51T/TPC-xx51H series.
While completing step A to F step by step, you can supply power to TPC-xx51T/TPC-xx51H
series now.
Note!
Make sure all wires follow the installation guidelines or it may cause
issues.
Note!
If you install a USB device or Mini PCIe card on the TPC-xx51T/
TPC-xx51H, please double check the voltage between V- and earth
ground, if the voltage is not almost equal with each other, we suggest to
short V- and earth ground with wiring.
15
TPC-xx51T/H User Manual
TPC-xx51T/H User Manual
16
Appendix
A
A
Serial Port Settings
A.1 Jumper, Dip switch and Connector location
A.1.1 Top
A.1.2 Bottom
TPC-xx51T/H User Manual
18
A.2.1 CMOS Clear Function (CN1)
CMOS Clear Function
Description
This jumper is used to select CMOS Clear Enable/Disable
Default
(1-2)
(2-3)
Enable (Clear CMOS)
(1-2)
Disable
(1-2) Disable
(2-3) Enable (Clear CMOS)
A.3 Switch Setting
COM2 RS232/422/485 mode setting (SW2)
COM2 RS232/422/485 mode setting
Description
This switch is used to select COM2 RS232/422/485 mode setting
Default
RS232 mode
RS232 Mode
Bit 1,2,3,4,5 ON
Bit 6,7,8,9,10 OFF
RS422 Master Mode
Bit 1,2,3,4,5,10 OFF
Bit 6,7,8,9 ON
RS422 Slave Mode
Bit 1,2,3,4,5 OFF
Bit 6,7,8,9,10 ON
19
TPC-xx51T/H User Manual
Appendix A Serial Port Settings
A.2 Jumper setting and Description
RS485 Mode
Bit 1,2,3,4,5,8,9 OFF
Bit 6,7,10 ON
A.3.1 Termination Resistor Select (SW3)
Termination Resistor Select
Description
This switch is used to select Termination Resistor (120 ohm) for long
distance transmission or device matching.
Default
Bit1 off & Bit2 off (ISO_COM2_DATA+ & ISO_COM2_RX-)
ISO_COM2_DATA+
Pin 1
ISO_COM2_RX-
Pin 2
ISO_COM2_R_RX+
Pin 3
Default
ISO_COM2_R_DATA- Pin 4
A.4 Connector Pin Definition
A.4.1 SATA connector (CN12)
1654004659 Serial ATA 7P 1.27mm 180D(M) DIP WATM-07DBN4A3B83.12
Pin
Signal
Description
1
GND
GND
2
A+
3
A-
Signal Pair A : TX+/(Transmit)
4
GND
GND
5
B-
6
B+
Signal Pair B : RX+/
(Receive)
7
GND
GND
TPC-xx51T/H User Manual
20
1655000453 WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIH VEI
Pin
Signal
Description
1
+V3.3SATA
SATA power output 3.3V/1A
2
+V5SATA
SATA power output 5V/1A
3
+V12SATA
SATA power output 12V/0.5A
4
GND
GND
5
GND
GND
A.4.3 Mini PCIE slot (MINIPCIE)
1654002538 MINI PCI E 52P 6.8mm 90D SMD AS0B226-S68N7H
Supports PCI1.1, PCI1.2 Power Definition
Pin
Signal
Description
52
+3.3Vaux /
+3.3V
Pin
PCI1.1 was +3.3V, PCI1.2 was +3.3Vaux 51
50
GND
49
Reserved
NC
48
+1.5V
47
Reserved
NC
46
NC
NC
45
Reserved
NC
44
NC
NC
43
The pin to select the Pin 2, 52 power
PIN43_MPCIE_
output for +3.3Vaux or +3.3V (PCI1.1
PWRSEL
was Reserved and PIC1.2 was GND
42
NC
NC
41
+3.3Vaux
40
GND
39
+3.3Vaux
38
USB_D+
36
USB_D-
34
GND
32
SMB_DATA
USB serial data interface compliant to
the USB 2.0 specification
SMBus data signal compliant to the
SMBus 2.0 specification
Signal
Description
Reserved
NC
37
GND
35
GND
33
PETp0
31
PETn0
29
GND
PCI Express differential transmit pair
30
SMB_CLK
28
+1.5V
27
GND
26
GND
25
PERp0
24
+3.3Vaux
23
PERn0
22
PERST#
Functional reset to the card
21
GND
20
W_DISABLE
#
Active low signal. This signal is used by
the system to disable radio operation on
add-in cards that implement radio fre19
quency applications. When implemented,
this signal requires a pull-up resistor on
the card.
Reserved
NC
18
GND
17
Reserved
NC
Key
Key
PCI Express differential receive pair
Key
Key
16
NC
NC
14
NC
12
NC
10
NC
NC
8
NC
NC
7
CLKREQ#
Reference clock request signal
6
1.5V
5
NC
NC
4
GND
3
NC
NC
2
+3.3Vaux /
+3.3V
1
WAKE#
Open Drain active Low signal. This signal is used to request that the system
return from a sleep/suspended state to
service a function initiated wake event.
15
GND
NC
13
REFCLK+
NC
11
REFCLK-
9
GND
PCI1.1 was +3.3V , PCI1.2 was
+3.3Vaux
* +3.3Vaux was suspend Power , power out to device +3.3V/1.1A
* +3.3V was core power
* +1.5V was core power, power out to device +1.5V/0.5A
21
TPC-xx51T/H User Manual
Appendix A Serial Port Settings
A.4.2 SATA Power connector (CN13)
A.4.4 CFast slot (CN14)
1653004849 CFast 24P 1.27mm 90D(M) SMD N7G24-A0B2RA-10-0HTThe host is connected to the CFast Card using a 7+17 pin connector
Pin
Segment
CFast Name Description
S1
SATA
SGND
Ground for signal integrity
S2
SATA
A+
S3
SATA
A-
Signal Pair A : TX+/(Transmit)
S4
SATA
SGND
Ground for signal integrity
S5
SATA
B-
S6
SATA
B+
Signal Pair B : RX+/
(Receive)
S7
SATA
SGND
Ground for signal integrity
Key
Key
PC1
PWR/CTL
CDI
NC
PC2
PWR/CTL
GND
GND
PC3
PWR/CTL
TBD
NC
PC4
PWR/CTL
TBD
NC
PC5
PWR/CTL
TBD
NC
PC6
PWR/CTL
TBD
NC
PC7
PWR/CTL
GND
GND
PC8
PWR/CTL
LED1
CF_PHYRDY LED
PC9
PWR/CTL
LED2
CF_HDDA LED
PC10 PWR/CTL
IO1
NC
PC11 PWR/CTL
IO2
NC
PC12 PWR/CTL
IO3
NC
PC13 PWR/CTL
PWR
PC14 PWR/CTL
PWR
PC15 PWR/CTL
PGND
PC16 PWR/CTL
PGND
PC17 PWR/CTL
CDO
CFast Power output to Device +3.3V / 1.2A
Ground for Power return
NC
A.4.5 Power in connector (CN18)
1652003104 PLUG-IN BLOCK 3P 5.08mm 90D(M) DIP ME050-50803
Pin
Signal
1
Power IN V+
2
Power IN V– (GND)
3
GND_EARTH
TPC-xx51T/H User Manual
Description
24VDC +-20% Power in
The GND_EARTH to connect a Screw hole for short with the
chassis GND
22
1652002996 PHONE JACK RJ45 14P 90D(M) DIP RTA-195AAK1A
RJ45 Pin Signal
Description
1


MDI0+

2
3
MDI0-
MDI1+



6
MDI1-
4
MDI2+
5
MDI2-
7
MDI3+
8
MDI3-




In BASE-T: Media Dependent Interface[0]:
1000BASE-T: In MDI configuration, MDI[0]+/- corresponds to BI_DA+/- and in MDI-X configuration MDI[0]+/corresponds to BI_DB+/-.
10BASE-T and 100BASE-TX: In MDI configuration,
MDI[0]+/- is used for the transmit pair and in MDIX
configuration MDI[0]+/- is used for the receive pair.
In BASE-T: Media Dependent Interface[1]:
1000BASE-T: In MDI configuration, MDI[1]+/- corresponds to BI_DB+ and in MDI-X configuration MDI[1]+/corresponds to BI_DA+/-.
10BASE-T and 100BASE-TX: In MDI configuration,
MDI[1]+/- is used for the receive pair and in MDI-X
configuration MDI[1]+/- is used for the transmit pair.
In BASE-T: Media Dependent Interface[3:2]:
1000BASE-T: In MDI and in MDI-X configuration,
MDI[2]+/- corresponds to BI_DC+/- and MDI[3]+/- corresponds to BI_DD+/-.
100BASE-TX: Unused.
10BASE-T: Unused.
Left LED
Right LED
10Link
100Link
1000 Link
Active
Off
Orange
Green
Green
23
TPC-xx51T/H User Manual
Appendix A Serial Port Settings
A.4.6 LAN RJ45 connector (CN7,CN8)
A.4.7 USB connector (CN10)
1654010199 USB Conn. 2.0+3.0 13P 90D(F) DIP UEA1112C-UHS6-4
Pin
Signal
Description
1, 10
USB VBUS
USB Power output ,USB2.0 5V/0.5A and USB3.0 5V/0.9A
2, 11
USB_P-
USB2.0 date -
3, 12
USB_P+
USB2.0 date +
4,13
GND
Ground for Power return
5
SSRX-
USB3.0 RX -
6
SSRX+
USB3.0 RX +
7
GND_DRAIN
Ground for signal return
8
SSTX-
USB3.0 TX -
9
SSTX+
USB3.0 TX +
A.4.8 COM1 RS232 connector (CN15)
1654000056 D-SUB Conn. 9P 90D(M) DIP 070241MR009S200ZU
Pin
RS232
1
DCD
2
RX
3
TX
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
1
2
6
TPC-xx51T/H User Manual
3
7
4
8
5
9
24
1654000056 D-SUB Conn. 9P 90D(M) DIP 070241MR009S200ZU
Pin
RS232
RS422
RS485
1
DCD
TX-
D-
2
RX
TX+
D+
3
TX
RX+
4
DTR
RX-
5
GND
GND
6
DSR
7
RTS
8
CTS
9
RI
1
2
6
3
7
25
4
8
GND
5
9
TPC-xx51T/H User Manual
Appendix A Serial Port Settings
A.4.9 COM2 RS232/422/485 connector (CN16)
TPC-xx51T/H User Manual
26
Appendix
B
B
Driver Installation and
Configuration
B.1 EC Driver Installation
Follow the steps below to install the EC drivers:
1.
2.
Launch folder \\EC\V1.03.0001
Install AdvEC_V1.03.0001.exe
3.
Click Next
TPC-xx51T/H User Manual
28
Click Install
5.
Click Finish
6.
Choose Yes, then click OK to restart
29
Appendix B Driver Installation and Configuration
4.
TPC-xx51T/H User Manual
B.2 EC Brightness Control Tool Installation
Note!
The EC driver must be installed first
Follow the steps below to install the EC brightness control tool:
1. Launch folder \\EC Brightness\V1.01.0002
2. Install AdvECBrightness_V1.01.0002.exe
3.
Click Next
TPC-xx51T/H User Manual
30
Click Install
5.
Click Finish
6.
Choose Yes, then click OK to restart
31
Appendix B Driver Installation and Configuration
4.
TPC-xx51T/H User Manual
B.3 EC Watchdog Timer Driver Installation
Note!
The EC driver must be installed first
Follow the steps below to install the EC Watchdog Timer driver:
1. Launch folder \\WDT\V1.30.0001
2. Install AdvWDT_v1.30.0001.exe
TPC-xx51T/H User Manual
32
Click Next
4.
Choose Advantech [EC]WDT, then click Next
33
Appendix B Driver Installation and Configuration
3.
TPC-xx51T/H User Manual
5.
Click Install
6.
Click Finish
TPC-xx51T/H User Manual
34
Choose Yes, then click OK to restart
35
Appendix B Driver Installation and Configuration
7.
TPC-xx51T/H User Manual
B.4 Intel Graphics Driver Installation
Follow the steps below to install the Intel Graphics driver:
1. Launch folder \\Graphics Driver\Intel EMGD win7 32 bit\
2. Install Setp.exe
3.
Click Next
TPC-xx51T/H User Manual
36
Click Yes
5.
Click Next
6.
Click Install
Appendix B Driver Installation and Configuration
4.
37
TPC-xx51T/H User Manual
7.
Click Next
8.
Choose Yes, then click Finish to restart
TPC-xx51T/H User Manual
38
Follow the steps below to install the Intel Chipset Software Installation Utility:
1. Launch \\Intel Chipset Software Installation Utility\SetupChipset_10.0.13_PV
2. Install SetupChipset.exe
3.
Click Next
39
TPC-xx51T/H User Manual
Appendix B Driver Installation and Configuration
B.5 Intel Chipset Software Installation Utility
Installation
4.
Click Accept
5.
Click Install
6.
Click Finish
TPC-xx51T/H User Manual
40
Follow the steps below to install the Intel Trusted Execution Engine driver:
1. Launch folder \\TXE\Intel TXE Firmware\Win7
2. Install kmdf-1.11-Win-6.1-x86.msu
3.
Click Yes
41
TPC-xx51T/H User Manual
Appendix B Driver Installation and Configuration
B.6 Intel® Trusted Execution Engine Driver
Installation
4.
Click Restart Now, then the system will restart
5.
Launch folder \\TXE\TXE_Win7_8_8.1_1.1.0.1089
6.
Install SetupTXE.exe
TPC-xx51T/H User Manual
42
Click Next
8.
Click Next
9.
Click Next
Appendix B Driver Installation and Configuration
7.
43
TPC-xx51T/H User Manual
10. Choose Yes, then click Finish to restart.
B.7 LAN Driver Installation
Follow the steps below to install the LAN driver:
1. Launch folder \\LAN\Win7 \Install_Win7_7077_11282013
2. Install setup.exe
TPC-xx51T/H User Manual
44
Click Next
4.
Click Install
Appendix B Driver Installation and Configuration
3.
45
TPC-xx51T/H User Manual
5.
Click Finish
TPC-xx51T/H User Manual
46
Follow the steps below to install the Windows 7 USB 3.0 driver:
1. Launch folder \\USB3\Win7\SetupUSB3_3.0.0.33
2. Install Setup.exe
3.
Click Next
47
TPC-xx51T/H User Manual
Appendix B Driver Installation and Configuration
B.8 Windows 7 USB 3.0 Driver Installation
4.
Click Yes
5.
Click Next
6.
Click Next
TPC-xx51T/H User Manual
48
Choose Yes, then click Finish to restart
B.9 Touchscreen Driver Installation
Follow the steps below to install the touchscreen driver:
1. Launch folder \\TS\PenMount Windows Universal Driver V2.4.1.320(WHQL)
2. Install Setup.exe
49
TPC-xx51T/H User Manual
Appendix B Driver Installation and Configuration
7.
3.
Click Next
4.
Click I Agree
5.
Click Install
TPC-xx51T/H User Manual
50
Click Finish
7.
Click Finish
Appendix B Driver Installation and Configuration
6.
51
TPC-xx51T/H User Manual
B.10 Touchscreen Calibration
Follow the steps below to install the touchscreen driver:
1. Launch PenMount Control Panel tool
2.
Double click PenMount 6000 USB
TPC-xx51T/H User Manual
52
Follow the process to calibration touch screen
Click OK to finish calibration
53
Appendix B Driver Installation and Configuration
3.
4.
TPC-xx51T/H User Manual
TPC-xx51T/H User Manual
54
Appendix
C
C
Windows 8.X BIOS
Setup
C.1 Windows 8.X BIOS Setup
1.
Entre BIOS setting menu then go to Advanced page for Miscellaneous
Configuration
2.
Select OS Selection to Widows 8.X TPC-xx51T/H User Manual
56
Appendix C Windows 8.X BIOS Setup
TPC-xx51T/H User Manual
57
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement