TCD-2100
TCD-2100
1-channel H.264 Video Encoder
Hardware User’s Manual
(DC 12V)
Ver. 2010/7/20
TCD-2100 Hardware User’s Manual
Table of Contents
0.
Precautions
3
1.
Introduction
4
Package Contents ........................................................................... 4
Features and Benefits ..................................................................... 5
Safety Instructions .......................................................................... 6
Physical description ........................................................................ 8
Basic Connections ......................................................................... 11
Product Specification .................................................................... 12
2.
Accessing Device
13
If you have DHCP server / router in your network: ...................... 13
If you do NOT have DHCP server / router in your network: ......... 13
2
www.acti.com
TCD-2100 Hardware User’s Manual
0. Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to
follow the safety instruction given may directly endanger people, cause damage to the system
or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
FCC/CE Regulation
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the users will be required to correct the
interference at their own expense.
3
www.acti.com
TCD-2100 Hardware User’s Manual
1. Introduction
Package Contents
TCD-2100
Power Adaptor (Optional)
Product CD
Accessory
Warranty Card
4
www.acti.com
TCD-2100 Hardware User’s Manual
Features and Benefits
This is a cutting-edge digital video surveillance device. It can compress and transmit real time
images with outstanding image quality through a standard TCP/IP network. This device is your
best choice to build an intelligent IP surveillance system.
H.264/MPEG-4/MJPEG Triple Codec Dual Streaming
This device supports 3 compression formats, H.264, MPEG-4 and MJPEG. It brings superior
image quality at 30 frames per second in D1 (720 x 480) / CIF (352 x 240) and QCIF(160 x
112). With hardware H.264 compression, the composite video inputs can be efficiently
compressed into H.264 stream without delay.
Built-in Hardware Motion Detection
No more external motion sensors are required. You may assign up to 3 video motion detection
areas. By tuning the object size and sensitivity, it will reliably detect objects passing though in
view. Hardware motion detection also offers better sensitivity and faster response time than
software motion detection.
Powerful Bundled Surveillance Software
To extend the capabilities of the device, a powerful surveillance program is included in the
package for free. Users can easily use an existing PC as a digital video recorder. Scheduled
recording and manual recording keep every important video recorded in the local hard disk.
Reliable and accurate motion detection with instant warning enables immediate response in
every condition. Quick and simple search and playback function lets you easily find the images
and video you want.
Software Development Kit Support
This device can be integrated or controlled by applications from third party software developers.
Software developers can save considerable efforts by using our Streaming Library or ActiveX
control. Please contact us for details on integration support.
Digital Time Code Embedded
The “Digital Time Code Embedded” function records video time in the video stream. Therefore,
each image frame is marked with its original recording time. It is very useful when users want
to find the video at an exact time or between a certain time intervals.
5
www.acti.com
TCD-2100 Hardware User’s Manual
Safety Instructions
Don’t use the power supply with other voltages
If you use a power supply with different voltage than the one included with this device, this
device may be damaged or inflict damage upon other equipments / personnel. All warranty of
this product will be voided in the situations above.
Don’t open the housing of the product
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Water and Moisture
Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool and the like.
Don’t use accessories not recommended by the manufacturer
Only install this device and the power supply in a dry place protected from weather
Servicing
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
6
www.acti.com
TCD-2100 Hardware User’s Manual
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
extensive work by a qualified technician to restore the video product to its normal
operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
7
www.acti.com
TCD-2100 Hardware User’s Manual
Physical description
1) Video Input / Output
The IP device allows one analog input of composite signals with BNC connectors.
2) Serial Port Connection via Terminal Block
Connect your serial port devices to the terminal block according to this table.
DESCRIPTION
PIN
NAME
RS-485
RS-422
RS-232
Tx
1
Tx+
D+
Tx+
2
Tx-
D-
Tx-
3
Rx+
Rx+
4
Rx-
Rx-
Rx
3) Dip Switch for Serial Port Configuration
The same terminal connections can be used for different protocols. Select which protocol to
use via this Dip Switch.
RS-485 or RS-222 (Default is RS-485)
RS-232 pin define
8
www.acti.com
TCD-2100 Hardware User’s Manual
4) Power LED
The LED will light up after device has successfully completed the boot process
5) Serial Port LED
LED will light up when serial port is active
6) Power Input
Connect the power adaptor here if your power input is DC12V.
PIN
NAME
DESCRIPTION
1
12V
DC Power Input
2
GND
Ground Pin
7) Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button (with a sharp tipped object, like a pen.)
Step 3: Reconnect the power cable while continuing to hold the reset button. The red
Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for
another second and turn off again. By this time the reset to default operation is already
completed. This will take around 20 seconds from power up. You may then release the
reset button. This length of time fluctuates slightly with the environment. The Power LED light
will come back on and stay on after a few more seconds. The unit will start up with factory
default settings automatically.
9
www.acti.com
TCD-2100 Hardware User’s Manual
Restore to Default
Complete
Power On
On (3s)
On
1s
Off (about 15s)
Off (10~15s)
Stay On
About 20 Seconds
8) Terminal Blocks for Digital Input / Output
The IP device supports one alarm input and one transistor output. Please connect DI with Pin 1
and 3 and connect DO with Pin 2 and 4.
PIN
NAME
1
GND
2
DC + 12V
3
Digital Input
4
Transistor Output
Connection design
DI
TTL-compatible logic levels
To trigger (low)
Logic level 0: 0V ~ 0.4V
Normal (high)
Logic level 1: 3.1V ~ 30V
Voltage
Current
10mA ~ 100mA
Connection design
Transistor (Open Drain)
DO
Voltage & Current
Internally powered at 12 V. Limit to no more than
24V DC if connected to external power, <100mA
9) Ethernet Port
The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this
IP device can auto detect the speed of local network segment (10Base-T/100Base-TX
Ethernet).
10
www.acti.com
TCD-2100 Hardware User’s Manual
Basic Connections
Follow the procedures below to connect the IP device to the respective apparatuses.
1) Connect an analog monitor to IP device video out (BNC connector)
2) Connect the power adaptor to IP device
3) Connect IP device’s Ethernet port to Network switch (via RJ45 connectors).
4) Connect a PC to the Ethernet switch (via RJ45 connectors)
11
www.acti.com
TCD-2100 Hardware User’s Manual
Product Specification
Compression
Picture Resolution
Video Compression
Bit Rate
Image Frame Rate
Video Input
Video Output
Audio Input
Audio Output
Alarm
Remote Control
External I/O
Network
Software
Operating
Power
Physical
Approvals
Composite Input
Composite Output
Compression
Audio Line Input
Compression
Audio Line Output
Input
Output
Serial Port
Reset Button
LED
Ethernet Port
Protocol
Web Browser
SDK
PTZ protocol*
Security
Temperature
Power Requirement
Power Consumption
Dimensions (WxHxD)
Weight
Certificate
TCD-2100
H.264/ MPEG-4/ MJPEG simultaneous dual streams selectable
Full D1 (720x480 in NTSC, 720x576 in PAL)
CIF (352 x 240 in NTSC, 352 x 288 in PAL)
QCIF(160 x 112 in NTSC, 176 x 144 in PAL)
28K ~ 6M bps
30fps at full D1 resolution (NTSC)
25fps at full D1 resolution (PAL)
CVBS, 1.0Vp-p with 75Ω loading, BNC Connector
N/A
N/A
N/A
N/A
N/A
1, TTL, Terminal Block
1, TTL, Terminal Block
RS-485: Half Duplex, Terminal Block
RS-422: Full Duplex, Terminal Block
RS-232: Full Duplex, Terminal Block
Factory Default
System status
Ethernet(10/100 Base-T), RJ45 Connector
TCP, UDP, IP, HTTP, DHCP, PPPoE, RTP, RTSP,IPv6, FTP, SMTP, DNS, DDNS,
NTP, ICMP, IGMP, ARP
Microsoft Internet Explorer 6.0 or above
ACTi SDK-10000
Pelco-D,Pelco-P V1 and V2, Dynacolor, Sony VISCA, American Dynamics
Password Protection: Configured by the Administrator
-10~50℃ (14℉~122℉)
DC12V±10%
3.6 W
103 mm x 28.5 mm x 76 mm
(4.06" x 1.12" x 2.99")
195 g(0.43 lb)
CE, FCC
12
www.acti.com
TCD-2100 Hardware User’s Manual
2. Accessing Device
If you have DHCP server / router in your network:
Many network server / routers are able to automatically provide IP addresses through DHCP. If
you are using such a network, just plug in your computer and IP device into the network and
your IP device will acquire network address by itself. Find and access the device with our IP
Utility program. You may download it at:
http://www.acti.com/product/detail/Software/ACTi_Utility_Suite
If you do NOT have DHCP server / router in your
network:
1. Configure your PC to use the same subnet by changing your PC’s IP address to the
subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254
except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.
2. The default IP used by this device is 192.168.0.100. Please make sure your PC is
NOT using this address and that no two equipments use the same IP address in
the network.
3. Change your IP address by going to Control Panel ->Manage Network Connections ->
Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.
13
www.acti.com
TCD-2100 Hardware User’s Manual
Please set the settings as below.


IP address: 192.168. 0.xxx

Subnet mask: 255.255.255.
0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP device. Please also
make sure that no two equipments
use the same IP address in the
same network..)
4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:
192.168.0.100
5. When you see the login window, please input default user and password:
Default User: Admin
Password: 123456
6. After logging in, you will see the video from camera. To go to the main menu, click
the ”Setup” button on the top left.
14
www.acti.com
TCD-2100 Hardware User’s Manual
If you are using a single device, this is enough to access the device.
If you are using multiple devices, you need to change the current device to another
unused IP address, so that when the next device is connected to the network, no two
devices use the same IP. Please perform the following steps.
7. Go to Network -> Connection Type
8. Change the IP mode to Static.
9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP
address or 192.168.0.100.). If this is not the first device you add to the network, please
also avoid other devices’ IPs.
15
www.acti.com
TCD-2100 Hardware User’s Manual
10. Click “Apply”
11. Please go to Maintain -> Save & Reboot, and click ”Apply”. Internet Explorer will close
after a few seconds. This is normal.
12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example,
192.168.0.101). For the second device or more you add into the network, please type
the correct IP.
13. Adjust the default Video setting by going to Video & Audio -> Media 1
16
www.acti.com
TCD-2100 Hardware User’s Manual
17
www.acti.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement