USP SERIES

USP SERIES
®
OPERATOR’S MANUAL
USP SERIES
Official H&K licensed product. Umarex holds the worldwide exclusive HK-Tradmark and exterior design copy license for use with this Umarex product, granted by HK, Inc., U.S.A.
H&K USP SERIES
TABLE OF CONTENTS
Use of this manual............................................................................................2
Safety Guidelines......................................................................................... 2-3
Warranty and Service................................................................................... 4-5
Specifications............................................................................................. 6-10
Contents ........................................................................................................11
Charging Gas.................................................................................................12
BB Loading.....................................................................................................13
Loading Magazine..........................................................................................14
Cocking..........................................................................................................14
Safety and Decocking....................................................................................14
Shooting.........................................................................................................15
Shooting Modes.............................................................................................15
Open Slide .....................................................................................................16
After Shooting.................................................................................................16
Hop-Up System .............................................................................................17
Hop-Up Adjustment Point ..............................................................................18
Disassembly............................................................................................. 19-20
Assembly........................................................................................................21
Troubleshooting .............................................................................................22
General Maintenance.....................................................................................23
Operating Under Unusual Conditions.............................................................23
Diagrams and Parts Lists ........................................................................ 24-42
1
USE OF THIS MANUAL
Before operating the Airsoft gun, read this manual in its entirety. Important safety topics
and tips are discussed throughout all of the chapters. It’s important that the operator know
the principles of gun handling safety and operation prior to firing the Airsoft gun.
SAFETY GUIDELINES
!
WARNING! Failure to follow safety guidelines may result
in serious injury.
Safety Distance
The effective shooting range is approximately 75 feet. BBs fired from this Airsoft gun may
travel further than intended. Make certain that you have an adequate backstop.
Eye Protection
Eye protection should be worn at all times when both shooting and maintaining your Airsoft
gun. Protect your eyes from silicone spray and BBs under spring pressure while performing
maintenance on your Airsoft gun.
Assume Every Gun is Always Loaded
Until you are certain the chamber is empty, treat every gun as if it were loaded. Do not
assume the chamber is empty based on your memory or someone else’s words. Always
remove the magazine and visually check to confirm the chamber is empty.
Beware of Barrel Obstructions
Ensure the Airsoft gun barrel is free of obstructions before you fire the gun. Even the
smallest obstruction such as lubrication or a stuck cleaning patch can cause a misfire or
malfunction.
Muzzle Control
Always keep the muzzle of the gun pointed in a safe direction. Never point the muzzle at a
person or object that you do not intend to shoot.
Keep Your Safety On
Keep the gun’s safety on until your sights are aligned on your target and you are ready to
fire.
Keep Your Finger Off The Trigger
Keep your finger off the trigger and out of the trigger guard until your sights are aligned on
your target and you are ready to fire.
!
WARNING! Airsoft BBs can be a choking hazard. Keep
them away from children.
2
H&K USP SERIES
SAFETY GUIDELINES
Identify Your Target and Backstop
Before you pull the trigger, make certain of your target and what is beyond it. The Airsoft
gun should never be fired at surfaces such as rocks, glass, water, or other hard surfaces
where BBs are likely to ricochet in unpredictable directions.
!
WARNING! Adult supervision is required for any person
under the age of 18.
Failure To Fire
If the Airsoft gun fails to fire, misfires, or malfunctions, do not look into the gun barrel. BBs
can become lodged into the chamber, and serious eye injury may occur.
Maintain Your Gun Properly
Performing proper maintenance, as outlined in this manual, ensures that your Airsoft
gun will be safe to shoot and will perform to its designed specifications for many years.
Alterations, modifications or adjustments may damage your Airsoft gun, make it unsafe to
shoot, and will void all warranty claims.
Store Your Gun Safely
Always store the Airsoft gun in a safe place, and out of the reach of children. Always
transport the Airsoft gun in a carrying case. Never display the Airsoft gun in a public place.
Keep the safety engaged, and remove the magazine before storing the Airsoft gun. Note:
it is your responsibility to take every reasonable precaution to ensure the safe storage and
transportation of your Airsoft gun.
Orange Tip
The orange tip on Airsoft guns helps Law Enforcement distinguish between the replica
guns from their real firearm counterparts. Altering the coloration or markings required by
state or Federal law so as to make the product look more like a firearm is dangerous and
may be a crime. Operator assumes all risks and responsibility when doing so.
Hazards of Being Mistaken for a Real Firearm
Airsoft guns have been mistaken by Police and Law Enforcement as real firearms. A
confrontation with law enforcement while carrying an Airsoft gun can result in serious injury
or even death. It is strongly advised to operate the Airsoft gun at a safe and legal location.
In the event that you are approached by Law Enforcement personnel, you must comply with
their instructions immediately to avoid an incident.
Alcohol, Medications and Drugs
Do not handle or operate your Airsoft gun while under the influence of alcohol, medication
or drugs.
Your Responsibility
Your Airsoft gun is well-engineered and manufactured to the highest standards. It was
carefully inspected before it was packaged and shipped from our factory. Its safe use
depends on you alone. You are the ultimate safety device. Like many other devices, your
Airsoft gun is safe unless handled in an irresponsible or uneducated manner.
3
WARRANTY AND SERVICE
KWA Performance Industries, Inc. is committed to serve our customers with the finest
quality products, the highest level of service, and customer satisfaction. Because of this,
we offer a 45-day warranty on all KWA products we import and distribute.
What is Covered
Except as specified below, this warranty covers all defects in material and workmanship
in KWA products occurring during the above warranty periods. The following are not
covered by the warranty: (1) Any product which is not imported and distributed in the
U.S.A. by KWA Performance Industries, Inc. (2) Any products not purchased in
the U.S.A. from an KWA AUTHORIZED RESELLER (Note: KWA AUTHORIZED RESELLER
can be identified by KWA AUTHORIZED RESELLER sticker displayed in the store. If you
are uncertain as to whether a dealer is a KWA AUTHORIZED RESELLER, please contact
KWA Performance Industries, Inc. as listed above). (3) Damaged deterioration or
malfunction resulting from: a) Accident, act of nature, abuse, misuse, neglect, unauthorized
product repair, opening of or modification or failure to follow instructions supplied with the
product. b) Repair or attempted repair by anyone not authorized by KWA Performance
Industries, Inc. c) Removal of the orange safety tip. (4) Use of the product outside the
U.S.A. (5) Damaged batteries or improper use of bullets (BBs), or non approved propellants
(ie. Propane, Red Gas, 134a…etc.) (6) Use in industrial, commercial, and/or professional
applications.
What KWA Will Pay For
If during the applicable warranty period from the date of the original purchase your KWA
product is found to be defective by KWA Performance Industries, Inc., KWA Performance
Industries, Inc. will repair, or at its option, replace with new, used, or equivalent model, the
defective product without charge for parts or labor.
How To Obtain Warranty Service
If your product needs service, it may be taken or shipped to KWA Performance Industries,
Inc. The following procedures apply whenever your unit must be transported for warranty
service:
• You must go to Help Desk at www.kwausa.com/support to obtain an RMA number.
THE RMA NUMBER MUST BE CLEARLY MARKED ON THE OUTSIDE OF THE
PACKAGE. PACKAGES WITHOUT AN RMA NUMBER CLEARLY MARKED WILL BE
REFUSED AND RETURNED TO THE SENDER.
• You are responsible for transporting your unit or arranging for its transportation.
• If shipment of your unit is required; you must pay the initial shipping fee, but we will
pay the return shipping charge if the repairs are covered by the warranty.
• WHEN RETURNING YOUR UNIT FOR WARRANTY SERVICE, A COPY OF THE
ORIGINAL SALES RECEIPT MUST BE ATTACHED.
• You must include the following: RMA number, your name, address, daytime telephone
number, model and serial number (if applicable) of the product and a description of
the problem.
4
H&K USP SERIES
NOTE: THE RMA NUMBER MUST BE CLEARLY MARKED ON THE OUTSIDE OF THE
PACKAGE. PACKAGES WITHOUT AN RMA NUMBER CLEARLY MARKED WILL BE
REFUSED AND RETURNED TO SENDER. NO EXCEPTIONS.
This Warranty is Only Valid in the United States
If your product does not require service, but you have questions regarding its operation,
please contact our Technical Services Department as listed below.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
OUR LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION,
OF ANY DEFECTIVE PRODUCT AND SHALL IN NO EVENT INCLUDE INCIDENTAL OR
CONSEQUENTIAL COMMERCIAL OR PROPERTY DAMAGES OF ANY KIND. WE ARE
NOT RESPONSIBLE FOR PRODUCTS LOST, STOLEN AND/OR DAMAGED DURING
SHIPPING.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AND IMPLIED WARRANTY
LASTS AND/OR DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights, but you may also have other rights which vary
from state to state. This Warranty may not be altered other than in writing signed by an
officer of KWA Performance Industries, Inc.
KWA Performance Industries, Inc.
18571 E. Gale Ave.
City of Industry, CA 91748-1339
626-581-1777
www.kwausa.com
5
SPECIFICATIONS
H&K USP COMPACT
• Overall Length: 17.9 cm [7.05”]
• Overall Height: 14.0 cm [5.51”]
• Inner Barrel Length: 78 mm
• Inner Barrel Diameter: 6.05 mm
• Weight: 0.73 kg [1.61 lbs]
• Caliber: 6 mm
• Magazine Capacity: 21 rounds
• Velocity: 101-104 MPS [330-340 FPS]
• Energy Output with 0.20g BB: 1.01 Joules
• Gas System: NS2
Special Features:
• Functional decocking safety
• Ambidextrous magazine release
• Accessory rails
• 3-dot combat sight
• Adjustable Hop-Up
• Realistic construction and field stripping
*Individual test results may vary depending on brand of BBs, type of gas, and chronograph used.
6
H&K USP SERIES
SPECIFICATIONS
H&K USP COMPACT TACTICAL
• Overall Length: 19.0 cm [7.48”]
• Overall Height: 14.5 cm [5.70”]
• Inner Barrel Length: 84 mm
• Inner Barrel Diameter: 6.05 mm
• Weight: 0.74 kg [1.63 lbs]
• Caliber: 6 mm
• Magazine Capacity: 21 rounds
• Velocity: 101-104 MPS [330-340 FPS]
• Energy Output with 0.20g BB: 1.01 Joules
• Gas System: NS2
Special Features:
• Functional decocking safety
• Ambidextrous magazine release
• Accessory rails
• Threaded barrel
• 3-dot combat sight
• Adjustable Hop-Up
• Realistic construction and field stripping
*Individual test results may vary depending on brand of BBs, type of gas, and chronograph used.
7
SPECIFICATIONS
H&K USP
• Overall Length: 21.5 cm [8.47”]
• Overall Height: 14.3 cm [5.63”]
• Inner Barrel Length: 100 mm
• Inner Barrel Diameter: 6.05 mm
• Weight: 0.88 kg [1.94 lbs]
• Caliber: 6 mm
• Magazine Capacity: 24 rounds
• Velocity: 104-107 MPS [340-350 FPS]
• Energy Output with 0.20g BB: 1.07 Joules
• Gas System: NS2
• Available Colors = Black, OD Green, and Desert Tan
Special Features:
• Functional decocking safety
• Ambidextrous magazine release
• Accessory rails
• 3-dot combat sight
• Adjustable Hop-Up
• Realistic construction and field stripping
*Individual test results may vary depending on brand of BBs, type of gas, and chronograph used.
8
H&K USP SERIES
SPECIFICATIONS
H&K USP TACTICAL
• Overall Length: 23 cm [9.06”]
• Overall Height: 14.7 cm [5.79”]
• Inner Barrel Length: 105 mm
• Inner Barrel Diameter: 6.05 mm
• Weight: 0.88 kg [1.94 lbs]
• Caliber: 6 mm
• Magazine Capacity: 24 rounds
• Velocity: 104-107 MPS [340-350 FPS]
• Energy Output with 0.20g BB: 1.07 Joules
• Gas System: NS2
Special Features:
• Functional decocking safety
• Ambidextrous magazine release
• Accessory rails
• Threaded barrel
• 3-dot combat sight
• Adjustable trigger stop
• Realistic construction and field stripping
*Individual test results may vary depending on brand of BBs, type of gas, and chronograph used.
9
SPECIFICATIONS
H&K USP MATCH
• Overall Length: 24.5 cm [9.65”]
• Overall Height: 15.4 cm [6.06”]
• Inner Barrel Length: 136 mm
• Inner Barrel Diameter: 6.05 mm
• Weight: 1.12 kg [2.47 lbs]
• Caliber: 6 mm
• Magazine Capacity: 28 rounds
• Velocity: 104-107 MPS [340-350 FPS]
• Energy Output with 0.20g BB: 1.07 Joules
• Gas System: NS2
Special Features:
• Functional decocking safety
• Ambidextrous magazine release
• Ambidextrous slide catch release
• Accessory rails
• Extended barrel with barrel weight
• Adjustable target sight
• Adjustable trigger stop
• Realistic construction and field stripping
*Individual test results may vary depending on brand of BBs, type of gas, and chronograph used.
10
H&K USP SERIES
CONTENTS
H&K USP COMPACT / H&K USPC TACTICAL / H&K USP / H&K USP TACTICAL /
H&K USP MATCH
Product Package Contents
1 H&K USP COMPACT / H&K USPC TACTICAL / H&K USP / H&K USP TACTICAL /
H&K USP MATCH Airsoft gun
1 Bottle of Silicone Oil
1 Magazine
1 Sample bag of Airsoft BBs
1 Hop-Up Adjustment Tool
1 Operator’s manual
11
CHARGING GAS
1.Release the magazine by pressing the magazine release button.
2. Push the gas canister nozzle into the charging valve. Make sure the canister is in
a vertical position when charging.
3. Charge the magazine until gas overflows from the charging valve.
!
WARNING: Sudden impact with a hard surface may cause
damage to the magazine.
Note: It is normal to have minor leaking from the charging valve during charging due to
high pressure built up inside the magazine. It is recommended to keep the gas release valve
slightly oiled. Room temperature is the ideal temperature for shooting. You may experience
a delayed action if the surrounding temperature drops below 68º F.
Note: Do not expose the magazine to direct sunlight or incinerate the magazine, as this
may cause the magazine to burst. It is strongly recommended to empty the gas from the
magazine after shooting. Be certain that the gas does not make contact with eyes or skin
while being released, as any contact will cause cold burns.
S
F
2
Magazine
Catch
3
1
Nozzle
Charging
Valve
Magazine
Green Gas safety tips:
• Check the canister for any cracks or leaks before using.
• Do not expose the canister to temperature over 104º F.
• Do not leave the canister directly over fire.
• Do not heat the canister.
• Keep the canister away from direct sunlight.
• Do not leave the canister in any type of vehicle.
12
H&K USP SERIES
LOADING BBs
1. Pull the magazine follower down until it locks.
2. Insert BBs into the magazine lip.
3. BBs should stack staggered for maximum round capacity: 48 rounds.
4. Make sure to have a 3mm clearance between BBs and the top lip of the magazine.
5. Push the magazine follower lock to release.
Note: Always use KWA Perfect BBs, size 0.2 or 0.25g. Using only KWA Perfect BBs can
give your Airsoft gun its best performance. Using recycled and low grade BBs may damage
the gun.
!
WARNING: Do not release the magazine follower when the
magazine is empty. Doing so will damage the magazine and
magazine follower.
2
4
Check for 3mm
clearance after
loading BBs.
3mm
Push
down
1 to lock
5
13
Push to
release
Magazine Lip
3
LOADING MAGAZINE
S
F
1. Place the magazine back into the magazine
well.
2. Push the magazine up until it clicks into a
locked position.
3. Pull the magazine down to assure that it has
been locked in place.
COCKING
Pull the slide to the rear-most position and release the slide. This will automatically
load the BBs into the chamber. The hammer will be in a cocked position. Make sure
not to skip this procedure. Skipping this step will cause a misfire on the first pull of the
trigger. The slide will stay open when the last BB is fired and ejected.
Chamber
Hammer
Down
Hammer
SAFETY AND DECOCKING LEVER
Push the safety lever upward to align the letter
“S” with the white bar. Safety is “ON”.
Push the safety lever downward to align the
letter “F” with the white bar. Safety is “Off”
(Ready to fire).
Hammer Decocking:
To decock the hammer, push the safety lever
downward and the hammer is safely decocked
without firing.
!
ON
OFF
S
S
FF
S
F
WARNING: After decocking hammer, you can still shoot with
double action mode if the safety is disengaged.
14
H&K USP SERIES
SHOOTING
1.Release the safety and pull the trigger. The blow-back action will load the BBs
automatically as the slide cycles back and forth.
2. Grasp the Airsoft gun firmly in your hand. To properly control the gun, grasp it with
a two-hand hold with one hand wrapped around the other.
!
WARNING: Never shoot gun in a horizontal or upside-down
position.
Safety
S
F
Trigger
SHOOTING MODES
Single Action Mode
For Single Action mode, simply pull back
the slide and quickly release it to chamber
the first BB, then pull the trigger to fire.
S
F
Double Action Mode
For Double Action mode, de-cock the
hammer then fire with the hammer in “at
rest (forward)” position.
15
S
F
OPEN SLIDE
The slide will remain open after the last BB has been fired and ejected. Remove the empty
magazine and replace it with a loaded magazine, then release the slide stop. The first BB
will be automatically loaded into the chamber.
Note: It is important to treat your gun as if it were loaded even when the slide is open.
Slide Stop
S
F
AFTER SHOOTING
After you are finished shooting, remove the magazine and visually examine the open
chamber to check for clearance. Make sure both the magazine and the chamber are clear
without BBs, then engage the safety lever.
CHECK
Make sure
chamber is
clear
16
H&K USP SERIES
HOP–UP SYSTEM
The Hop-Up device is one of KWA’s standard features, giving Airsoft BBs greater stability,
further travel and increased accuracy. Airsoft BBs are light-weight and can be affected by
wind when fired. With the Hop-Up system, the trajectory of the Airsoft BBs can be adjusted
according to the shooting environment or surroundings.
HOP-UP ADJUSTMENT
To adjust the Hop-Up, make sure the magazine is loaded and that you have at least 65 feet
of clearance for a test fire before making any adjustments.
1. Test fire the gun for 10 to 20 rounds and observe the BB’s traveling pattern.
2.Remove the magazine.
3. Open the slide and place adjusting tool into the slotted chamber ring. Turn the
adjusting ring a 1/4-inch at a time.
4. If the BBs are dropping too quickly, move the adjusting ring to the left or
counter-clockwise to give the BB more hop. If the BBs are dropping too slowly,
move the adjusting ring to the right or clock-wise.
5. Test fire and adjust as needed.
More Hop
Less
Hop
17
HOP-UP ADJUSTMENT POINT
HOP UP
EFFECTIVENESS
BB TRAJECTORY PATTERN
ADJUSTMENTS
NOT
EFFECTIVE
BB DROPS FREELY
TURN KNOB
TO LEFT
SLIGHTLY
BB TRAVELS AT SHORT TRAJECTORY
PATH
TURN KNOB
SLIGHTLY TO
LEFT
PROPERLY
BB TRAVELS DISTANCE AT FLAT
TRAJECTORY PATH
NO
ADJUSTMENT
MADE
OVERLY
BB TRAVELS FLAT IN SHORT DISTANCE,
THEN GOES UP IN CURVE AND DROPS
FREELY
TURN KNOB
SLIGHTLY TO
RIGHT
EXTREMELY
EFFECTIVE
BB TRAVELS AT UNSTABLE SPEED AND
IRREGULAR PATH
TURN KNOB
TO RIGHT
18
H&K USP SERIES
DISASSEMBLY
(H&K USP COMPACT, H&K USP COMPACT TACTICAL, H&K USP and
H&K USP TACTICAL)
It is not recommended to disassemble the gun unless for general maintenance, or to clear
BBs jammed inside the barrel.
1.Remove the magazine by depressing the magazine releases on either side of the
Airsoft gun.
2. Check and clear the chamber of BBs.
3. Pull back slide until the cut out slot on the slide aligns with the front end of the
slide stop.
4. While holding the slide in position, remove the slide-stop by pushing on the
release pin on the right side of frame. Pull off the slide-stop from the left side of
the frame.
5. Glide the slide forward, away from the frame.
6.Remove the guide rod and spring.
7. Slide the barrel out from the bottom of the slide.
4
3
Push Slide Stop
Release Pin
S
F
5
Align
S
F
Slide Frame
7
6
19
Recoil Spring & Guide
Barrel
Unit
DISASSEMBLY (H&K USP MATCH)
1.Remove the magazine by pressing the magazine releases on either side of the
Airsoft gun.
2.Check and clear the chamber of BBs.
3. Unscrew the barrel weight screws from the H&K USP Match using a 3mm, or
equivalent, allen wrench.
4. Remove the barrel weight from the H&K USP Match.
5.Remove the slide stop from the H&K USP Match using a 2.5mm, or equivalent,
allen wrench.
6. Glide the slide forward, away from the frame.
7.Remove the guide rod and spring.
8. Slide the barrel out from the bottom of the slide.
3
Barrel Weight
Remove
4
6
5
Barrel Weight
Slide Stop
S
F
Slide Frame
8
Recoil Spring & Guide
7
Barrel
Unit
20
H&K USP SERIES
ASSEMBLY
(H&K USP COMPACT, H&K USP COMPACT TACTICAL, H&K USP and
H&K USP TACTICAL)
1. Place the barrel into the slide from underneath.
2. Install the recoil spring and guide rod into position.
3. Put the assembled slide onto the frame rails and glide it toward the rear of the
Airsoft gun until cut-out slot on the slide aligns with the slide stop hole.
4. Insert the slide stop.
5. Pull the slide to the rear most position and then release.
6. Install the magazine.
ASSEMBLY (H&K USP MATCH)
1. Place the barrel into the slide from underneath.
2. Install the recoil spring and guide rod into position.
3. Put the assembled slide onto the frame rails and glide it toward the rear of the
Airsoft gun untill the cut-out slot on the slide aligns with the slide stop hole.
4. Install the slide stop using a 2.5mm allen wrench.
5. Pull the slide to the rear most position and then release.
6. Install the barrel weight using a 3mm allen wrench.
7. Install the magazine.
NOTE: After assembly is completed, cycle the slide back and forth to insure proper
assembly.
21
BASIC TROUBLESHOOTING GUIDE FOR PISTOL
SYMPTOMS
POSSIBLE CAUSE
SOLUTIONS
Slide jams / Will not complete cycle
Dry internal
Add silicone to cylinder / main seal / rails
Double feeds BBs into
chamber / BB’s roll out of barrel
Hop-up adjustment too tight
Release hop-up or replace bucking
BBs will not release from magazine /
bent mag lip/ check bb condition
Bent magazine lip
Replace magazine lip
Leaking release valve & charging valve
Dry O-ring
Add silicone oil to valves
Slide stop engages while shooting BBs
Weak slide stop spring
Adjust tension
Magazine base plate will not lock
Broken base plate lock
Replace base plate lock
Magazine base leaking air
Worn out base seal
Replace magazine base seal
Cylinder will not load BBs into chamber
Broken cylinder tap
Replace cylinder
Trigger will not reset
Worn out trigger spring /
trigger bar spring
Replace trigger spring / trigger bar spring
22
H&K USP SERIES
GENERAL MAINTENANCE FOR KWA GAS BLOW BACK
Green gas is a liquid propellant which tends to dry out the seals and o-rings. With lubricating
silicone oil, it will extend the life of the seals and o-rings and prevent gas leaks.
Use only the recommended 100% silicone oil, available for purchase at the Airsoft dealer
where you purchased your KWA products. Any other type of lubricant may damage the
products.
Lightly lubricate the recoil spring, cylinder and moving parts with a few drops of oil.
Lubricating the seals and o-rings are essential. Unload BBs from the magazine. Make sure
the magazine is free of gas before lubricating the magazine’s charging valve and release
valve.
Operating Under Unusual Conditions
Unusual conditions are defined as any condition requiring special maintenance.
Perform maintenance outlined for the climate similar to your operational area.
Extreme Cold:
Operating an Airsoft gas gun in extremely cold temperatures is not recommended. Cold
temperatures will cause the Hop-up Bucking to harden, reducing its effectiveness. Gas
will not expand properly in cold temperatures, so both the cycling rate and power will be
dramatically reduced.
Extreme Heat:
Operating an Airsoft gas gun in extremely hot temperatures is also not recommended.
Leaving the gun in direct sunlight for long periods of time, or operating in extremely hot
areas will cause the gas to over-expand, damaging the internal workings of the gun. The
increase in internal pressure from the expanding gas can also damage the seals and cause
leaks in the magazine.
Dust or Sand:
Dust or sand can get into a gas gun and cause malfunctions and/or excessive wear. Keep
the gun covered whenever possible. Use lubricant sparingly, as lube naturally attracts dirt
and other particles. After use in a dusty area, always field strip the gun (refer to Disassembly
Section) and clean any areas you can reach with a soft, lint-free cloth.
23
H&K USP COMPACT PARTS DIAGRAM
41
33
34
36
116
35
3HK
121
13
12
120
6
126
37
45
66
90
47
1HK
53
81
17
72
1
85
125
32
19
18
89
73
5
82
4
24
H&K USP SERIES
H&K USP COMPACT PARTS DIAGRAM
21
92
6
9
2HK
8
48
91
22
7
117
9
49
38
42
11
15
50
80
118
28
84
27 122
68
69
83
87
20
29
26
88
65
16
71
70
51
86
25
69
123
44
24
30 119
52
23
14
55
25
75
95
74
H&K USP COMPACT PARTS LIST
Parts #
Description
Parts #
Description
Parts #
Description
199-0103-92
CYLINDER RETURN
SPRING x2
199-0103-95
FIRING PIN SPRING
199-0103-1HK FRAME
199-0103-41
INNER BARREL
199-0103-2HK SLIDE
199-0103-42
MAIN SEAL BASE
199-0103-3HK OUTER BARREL
199-0103-44
TRIGGER PIN SLEEVE
199-0103-4
MAIN SPRING HOUSING
199-0103-45
BASE PIN
199-0103-5
HAMMER STRUT LOCK
199-0103-47
RECOIL SPRING GUIDE
199-0103-6
CYLINDER
199-0103-48
JET NOZZLE PIN
199-0103-7
JET NOZZLE
199-0103-49
MAIN SEAL CAP
199-0103-8
EXTRACTOR
199-0103-50
TRIGGER BAR
199-0103-9
SIGHT INSERTS x3
199-0103-51
199-0103-11
FIRING PIN SLEEVE
SAFETY DECOCKING
LEVER BAR
199-0103-12
HOP-UP CYLINDER
199-0103-52
RIGHT SEAR PLATE
199-0103-53
HAMMER STRUT
199-0103-13
HOP-UP CYLINDER
CLAMP
199-0103-55
SERIAL NUMBER PLATE
199-0103-125
199-0103-14
INNER FRAME
199-0103-65
IMPACT BLOCK BASE PIN
199-0103-126 HOP-UP BALL BEARING
199-0103-15
BREACH
199-0103-66
RECOIL SPRING SPACER
199-0103-16
HAMMER
199-0103-68
IMPACT BLOCK PIN
199-0103-17
SAFETY LEVER SLEEVE
199-0103-69
PLUNGER X2
199-0103-18
SAFETY LEVER
199-0103-70
HAMMER STRUT PIN
199-0103-19
SLIDE CATCH LEVER
199-0103-71
SEAR PIN
199-0103-20
TRIGGER
199-0103-72
TRIGGER PIN
199-0103-21
FRONT SIGHT
199-0103-73
199-0103-22
REAR SIGHT
MAIN SPRING HOUSING
PIN
199-0103-23
LEFT SEAR
199-0103-74
FIRING PIN
199-0103-24
RIGHT SEAR
199-0103-75
BASE SCREW
199-0103-25
IMPACT BLOCK BASE
199-0103-80
SEAR SPRING
199-0103-26
IMPACT BLOCK BAR
199-0103-81
HAMMER STRUT SPRING
199-0103-27
IMPACT BLOCK
199-0103-82
HAMMER STRUT
LOCKING PIN
199-0103-28
RESET LEVER
199-0103-83
RESET LEVER SPRING
199-0103-29
DECOCKING LEVER PLATE
199-0103-84
IMPACT BLOCK SPRING
199-0103-30
SAFETY LEVER RETAINER
199-0103-85
SAFETY LEVER SPRING
199-0103-32
MAGAZINE CATCH
199-0103-86
199-0103-33
INNER BARREL HOUSING
DECOCKING LEVER
SPRING
199-0103-34
INNER BARREL CLAMP
199-0103-87
TRIGGER SPRING
199-0103-35
INNER BARREL BASE
199-0103-88
TRIGGER BAR SPRING
199-0103-36
BB FEED RAMP
199-0103-89
MAGAZINE CATCH
SPRING
199-0103-37
HOP-UP BUCKING
199-0103-90
RECOIL SPRING
199-0103-38
MAIN SEAL
199-0103-91
JET NOZZLE SPRING
199-0103-116 BARREL CLAMP SCREW
199-0103-117 MAIN SEAL CAP SCREW
199-0103-118 INNER FRAME SCREW
199-0103-119 BREACH SCREW
199-0103-120 FEED RAMP SCREW
199-0103-121
RECOIL SPRING
RETAINING CLIP
199-0103-122 IMPACT BLOCK RETAINER
199-0103-123 IMPACT PIN
MAGAZINE CATCH ROLL
PIN
26
H&K USP SERIES
H&K USP COMPACT TACTICAL PARTS DIAGRAM
41
33
34
36
13
116
12
120
35
37
45
121
58HK
66
90
47
53
1HK
81
17
72
85
125
19
32
18
89
5
73
82
27
4
H&K USP COMPACT PARTS DIAGRAM
59
2HK
92
6
8
48
91
60
7
117
49
38
42
11
15
75
95
74
119
50
80
84
118
14
28
27
52
122
25
68
30
24
23
69
88
26
69
83
55
44
87
16
65
71
70
29
20
51
86
28
H&K USP SERIES
H&K USP COMPACT TACTICAL PARTS LIST
Parts #
Description
Parts #
Description
Parts #
Description
199-0103-92
CYLINDER RETURN
SPRING x2
199-0103-95
FIRING PIN SPRING
199-0103-1HK FRAME
199-0103-42
MAIN SEAL BASE
199-0103-2HK SLIDE
199-0103-44
TRIGGER PIN SLEEVE
199-0103-4
MAIN SPRING HOUSING
199-0103-45
BASE PIN
199-0103-5
HAMMER STRUT LOCK
199-0103-47
RECOIL SPRING GUIDE
199-0103-6
CYLINDER
199-0103-48
JET NOZZLE PIN
199-0103-7
JET NOZZLE
199-0103-49
MAIN SEAL CAP
199-0103-8
EXTRACTOR
199-0103-50
TRIGGER BAR
199-0103-9
SIGHT INSERTS x3
199-0103-51
199-0103-11
FIRING PIN SLEEVE
SAFETY DECOCKING
LEVER BAR
199-0103-12
HOP-UP CYLINDER
199-0103-52
RIGHT SEAR PLATE
HAMMER STRUT
199-0103-13
HOP-UP CYLINDER
CLAMP
199-0103-53
199-0103-55
SERIAL NUMBER PLATE
199-0103-14
INNER FRAME
199-0103-58HK INNER BARREL
199-0103-125
199-0103-15
BREACH
199-0103-65
IMPACT BLOCK BASE PIN
199-0103-126 HOP-UP BALL BEARING
199-0103-16
HAMMER
199-0103-66
RECOIL SPRING SPACER
199-0103-17
SAFETY LEVER SLEEVE
199-0103-68
IMPACT BLOCK PIN
199-0103-18
SAFETY LEVER
199-0103-69
PLUNGER X2
199-0103-19
SLIDE CATCH LEVER
199-0103-70
HAMMER STRUT PIN
199-0103-20
TRIGGER
199-0103-71
SEAR PIN
199-0103-21
FRONT SIGHT
199-0103-72
TRIGGER PIN
199-0103-22
REAR SIGHT
199-0103-73
199-0103-23
LEFT SEAR
MAIN SPRING HOUSING
PIN
199-0103-24
RIGHT SEAR
199-0103-74
FIRING PIN
199-0103-25
IMPACT BLOCK BASE
199-0103-75
BASE SCREW
199-0103-26
IMPACT BLOCK BAR
199-0103-80
SEAR SPRING
199-0103-27
IMPACT BLOCK
199-0103-81
HAMMER STRUT SPRING
199-0103-28
RESET LEVER
199-0103-82
HAMMER STRUT
LOCKING PIN
199-0103-29
DECOCKING LEVER PLATE
199-0103-83
RESET LEVER SPRING
199-0103-30
SAFETY LEVER RETAINER
199-0103-84
IMPACT BLOCK SPRING
199-0103-32
MAGAZINE CATCH
199-0103-85
SAFETY LEVER SPRING
199-0103-33
INNER BARREL HOUSING
199-0103-86
199-0103-34
INNER BARREL CLAMP
DECOCKING LEVER
SPRING
199-0103-35
INNER BARREL BASE
199-0103-87
TRIGGER SPRING
199-0103-36
BB FEED RAMP
199-0103-88
TRIGGER BAR SPRING
199-0103-37
HOP-UP BUCKING
199-0103-89
MAGAZINE CATCH
SPRING
199-0103-38
MAIN SEAL
199-0103-90
RECOIL SPRING
199-0103-41
INNER BARREL
199-0103-91
JET NOZZLE SPRING
29
199-0103-116 BARREL CLAMP SCREW
199-0103-117 MAIN SEAL CAP SCREW
199-0103-118 INNER FRAME SCREW
199-0103-119 BREACH SCREW
199-0103-120 FEED RAMP SCREW
199-0103-121
RECOIL SPRING
RETAINING CLIP
199-0103-122 IMPACT BLOCK RETAINER
199-0103-123 IMPACT PIN
MAGAZINE CATCH ROLL
PIN
H&K USP COMPACT, H&K USP COMPACT TACTICAL MAGAZINE
DIAGRAM AND PARTS LIST
99
102
110
103
111
107
108
113
101
97
104
109
105
Parts #
Description
199-0103-97
MAGAZINE BODY
199-0103-98
MAGAZINE BASE
199-0103-99
MAGAZINE LIP
106
98
100
112
199-0103-100 MAGAZINE BASE PLATE LOCK
199-0103-101 MAGAZINE BASE PLATE
199-0103-102 MAGAZINE FOLLOWER
199-0103-103 MAGAZINE NOZZLE SEAL
199-0103-104 MAGAZINE EXPANSION TUBE
199-0103-105 MAGAZINE BASE LOCK PIN “SMALL”
199-0103-106 MAGAZINE BASE LOCK LARGE PINS X 2
199-0103-107 MAGAZINE LIP PINS X 2
199-0103-108 MAGAZINE FOLLOWER SPRING
199-0103-109 MAGAZINE BASE SEAL
199-0103-110 MAGAZINE FOLLOWER LOCK SPRING
199-0103-111 MAGAZINE FOLLOWER LOCK
199-0103-112 MAGAZINE CHARGING VALVE
199-0103-113 MAGAZINE RELEASE VALVE
30
H&K USP SERIES
H&K USP DIAGRAM
154
143
121
36
144
131HK
116
149
13
45
12
126
37
120
168
145
151
169
150
124
164
155
129HK
17
85
72
163
125
141
32
89
140
167
152
134
82
132
31
21
135
92
9
130HK
48
91
8
7
117
49
22
9
38
153
11
15
75
95
74
119
138
80
118
68
84
27
162
122
25
28
23
69
83
30
52
24
26
69
123
88
71
44
87
142
29
139
65
51
70
86
32
H&K USP SERIES
H&K USP PARTS LIST
Parts #
Description
Parts #
Description
Parts #
Description
199-0103-7
JET NOZZLE
199-0103-75
PISTON BASE SCREW
199-0103-140
SAFETY LEVER
199-0103-8
EXTRACTOR
199-0103-80
SEAR SPRING
199-0103-141
SLIDE CATCH LEVER
199-0103-9
SIGHT INSERTS x 3
199-0103-82
199-0103-142
TRIGGER
199-0103-11
INNER BARREL
RETAINING RING
HAMMER STRUT
LOCKING PIN
RESET LEVER PLUNGER
SPRING
199-0103-143
INNER BARREL HOUSING
199-0103-83
199-0103-144
INNER BARREL CLAMP
199-0103-84
IMPACT BLOCK SPRING
199-0103-145
INNER BARREL BASE
199-0103-85
SLIDE STOP SPRING
199-0103-149
RECOIL SPRING SPACER
(LARGE)
199-0103-12
HOP-UP CYLINDER
199-0103-13
HOP-UP CYLINDER
CLAMP
199-0103-15
BREACH
199-0103-86
SAFETY LEVER SPRING
199-0103-17
SAFETY LEVER SLEEVE
199-0103-87
TRIGGER SPRING
199-0103-150
RECOIL SPRING SPACER
(SMALL)
199-0103-21
FRONT SIGHT
199-0103-88
199-0103-151
RECOIL SPRING DIVIDER
199-0103-22
REAR SIGHT
TRIGGER BAR PLUNGER
SPRING
LEFT SEAR
199-0103-89
MAGAZINE CATCH
SPRING
199-0103-152
199-0103-23
MAIN SPRING HOUSING
PIN
199-0103-24
RIGHT SEAR
199-0103-91
JET NOZZLE SPRING
199-0103-153
MAIN SEAL BASE
199-0103-25
IMPACT BLOCK BAR
INNER BARREL
199-0103-26
IMPACT BLOCK BASE
CYLINDER RETURN
SPRINGS x 2
199-0103-154
199-0103-92
199-0103-155
RECOIL SPRING GUIDE
199-0103-27
IMPACT BLOCK
199-0103-95
FIRING PIN SPRING
199-0103-162
TRIGGER BAR
199-0103-28
RESET LEVER
199-0103-116
BARREL CLAMP SCREW
199-0103-163
HAMMER STRUT
199-0103-29
SAFETY LEVER PLATE
199-0103-117
MAIN SEAL CAP SCREW
199-0103-164
SERIAL NUMBER PLATE
199-0103-30
SAFETY LEVER RETAINER
199-0103-118
INNER FRAME SCREW
199-0103-167
HAMMER STRUT SPRING
199-0103-32
MAGAZINE CATCH
199-0103-119
BREACH SCREW
199-0103-168
199-0103-36
BB FEED RAMP
199-0103-120
FEED RAMP SCREW
OUTER RECOIL SPRING
(LARGE)
RECOIL SPRING
RETAINING CLIP
199-0103-169
INNER RECOIL SPRING
(SMALL)
199-0103-37
HOP-UP BUCKING
199-0103-121
199-0103-38
MAIN SEAL
199-0103-122
IMPACT BLOCK RETAINER
199-0103-44
TRIGGER PIN SLEEVE
199-0103-123
IMPACT BLOCK BASE PIN
199-0103-45
INNER BARREL BASE PIN
199-0103-48
JET NOZZLE PIN
199-0103-124
RECOIL SPRING DIVIDER
PIN
199-0103-49
MAIN SEAL CAP
199-0103-125
MAGAZINE CATCH ROLL
PIN
199-0103-51
SAFETY LEVER BAR
199-0103-126
HOP-UP BALL BEARING
199-0103-52
RIGHT SEAR PLATE
199-0103-129HK FRAME
199-0103-65
IMPACT BLOCK
EXTENSION
199-0103-130HK SLIDE
199-0103-68
IMPACT BLOCK PIN
199-0103-69
PLUNGER X2
199-0103-70
HAMMER STRUT PIN
199-0103-71
SEAR PIN
199-0103-72
TRIGGER PIN
199-0103-74
FIRING PIN
33
199-0103-131HK OUTER BARREL
199-0103-132
MAIN SPRING HOUSING
199-0103-134
HAMMER STRUT LOCK
199-0103-135
CYLINDER
199-0103-138
INNER FRAME
199-0103-139
HAMMER
H&K USP MAGAZINE DIAGRAM AND PARTS LIST
110
196
102
111
103
107
108
113
198A
194
200
100
203
105
201
195
Parts #
Description
199-0103-100
MAGAZINE BASE PLATE LOCK
199-0103-102
MAGAZINE FOLLOWER
199-0103-103
MAGAZINE NOZZLE SEAL
199-0103-105
MAGAZINE BASE LOCK PIN “SMALL”
199-0103-107
MAGAZINE LIP PINS tX 2
199-0103-108
MAGAZINE FOLLOWER SPRING
199-0103-110
MAGAZINE FOLLOWER LOCK SPRING
199-0103-111
MAGAZINE FOLLOWER LOCK
199-0103-112
MAGAZINE CHARGING VALVE
199-0103-113
MAGAZINE RELEASE VALVE
199-0103-194
MAGAZINE BODY
199-0103-195
MAGAZINE BASE
199-0103-196
MAGAZINE LIP
112
199-0103-198A MAGAZINE BASE PLATE
199-0103-200
MAGAZINE EXPANSION TUBE
199-0103-201
MAGAZINE BASE PINS X 2
199-0103-203
MAGAZINE BASE SEAL
34
H&K USP SERIES
H&K USP TACTICAL PARTS DIAGRAM
154
244
143
144
211HK
121
36
116
13
45
12
149
126
37
120
145
168
151
169
164
150
124
155
129HK
256
254
163
17
85
72
125
141
32
167
89
255
152
35
134
82
132
H&K USP TACTICAL PARTS DIAGRAM
258
239
237
233
257
258
238
241
257
234
227
135
240
92
232
130HK
91
48
8
7
117
49
38
153
11
138
80
118
68
84
122
27
25
28
23
83
30
52
24
26
69
75
15
162
95
74
119
69
123
88
71
44
87
29
139
65
243
51
70
236
86
36
H&K USP SERIES
H&K USP TACTICAL PARTS LIST
Parts #
Description
Parts #
199-0103-7
199-0103-8
JET NOZZLE
EXTRACTOR
INNER BARREL RETAINING
RING
HOP-UP CYLINDER
HOP-UP CYLINDER
CLAMP
BREACH
SAFETY LEVER SLEEVE
LEFT SEAR
RIGHT SEAR
IMPACT BLOCK BAR
IMPACT BLOCK BASE
IMPACT BLOCK
RESET LEVER
SAFETY LEVER PLATE
SAFETY LEVER RETAINER
MAGAZINE CATCH
BB FEED RAMP
HOP-UP BUCKING
MAIN SEAL
TRIGGER PIN SLEEVE
INNER BARREL BASE PIN
JET NOZZLE PIN
MAIN SEAL CAP
SAFETY LEVER BAR
RIGHT SEAR PLATE
IMPACT BLOCK
EXTENSION
IMPACT BLOCK PIN
PLUNGER X2
HAMMER STRUT PIN
SEAR PIN
TRIGGER PIN
FIRING PIN
PISTON BASE SCREW
SEAR SPRING
HAMMER STRUT
LOCKING PIN
RESET LEVER PLUNGER
SPRING
IMPACT BLOCK SPRING
SLIDE STOP SPRING
SAFETY LEVER SPRING
TRIGGER SPRING
TRIGGER BAR PLUNGER
SPRING
199-0103-89
199-0103-91
199-0103-11
199-0103-12
199-0103-13
199-0103-15
199-0103-17
199-0103-23
199-0103-24
199-0103-25
199-0103-26
199-0103-27
199-0103-28
199-0103-29
199-0103-30
199-0103-32
199-0103-36
199-0103-37
199-0103-38
199-0103-44
199-0103-45
199-0103-48
199-0103-49
199-0103-51
199-0103-52
199-0103-65
199-0103-68
199-0103-69
199-0103-70
199-0103-71
199-0103-72
199-0103-74
199-0103-75
199-0103-80
199-0103-82
199-0103-83
199-0103-84
199-0103-85
199-0103-86
199-0103-87
199-0103-88
37
Description
MAGAZINE CATCH SPRING
JET NOZZLE SPRING
CYLINDER RETURN
199-0103-92
SPRINGS x 2
199-0103-95
FIRING PIN SPRING
199-0103-116 BARREL CLAMP SCREW
199-0103-117 MAIN SEAL CAP SCREW
199-0103-118 INNER FRAME SCREW
199-0103-119 BREACH SCREW
199-0103-120 FEED RAMP SCREW
RECOIL SPRING
199-0103-121
RETAINING CLIP
199-0103-122 IMPACT BLOCK RETAINER
199-0103-123 IMPACT BLOCK BASE PIN
RECOIL SPRING DIVIDER
199-0103-124
PIN
MAGAZINE CATCH ROLL
199-0103-125
PIN
199-0103-126 HOP-UP BALL BEARING
199-0103-129HK FRAME
199-0103-130HK SLIDE
199-0103-132 MAIN SPRING HOUSING
199-0103-134 HAMMER STRUT LOCK
199-0103-135 CYLINDER
199-0103-138 INNER FRAME
199-0103-139 HAMMER
199-0103-141 SLIDE CATCH LEVER
199-0103-143 INNER BARREL HOUSING
199-0103-144 INNER BARREL CLAMP
199-0103-145 INNER BARREL BASE
RECOIL SPRING SPACER
199-0103-149
(LARGE)
RECOIL SPRING SPACER
199-0103-150
(SMALL)
199-0103-151 RECOIL SPRING DIVIDER
MAIN SPRING HOUSING
199-0103-152
PIN
199-0103-153 MAIN SEAL BASE
199-0103-129 FRAME
199-0103-130 SLIDE
199-0103-132 MAIN SPRING HOUSING
199-0103-134 HAMMER STRUT LOCK
199-0103-135 CYLINDER
199-0103-138 INNER FRAME
199-0103-139 HAMMER
199-0103-141 SLIDE CATCH LEVER
199-0103-143 INNER BARREL HOUSIN
Parts #
199-0103-144
199-0103-145
Description
INNER BARREL CLAMP
INNER BARREL BASE
RECOIL SPRING SPACER
199-0103-149
(LARGE)
RECOIL SPRING SPACER
199-0103-150
(SMALL)
199-0103-151 RECOIL SPRING DIVIDER
MAIN SPRING HOUSING
199-0103-152
PIN
199-0103-153 MAIN SEAL BASE
199-0103-154 INNER BARREL
199-0103-155 RECOIL SPRING GUIDE
199-0103-162 TRIGGER BAR
199-0103-163 HAMMER STRUT
199-0103-164 SERIAL NUMBER PLATE
199-0103-167 HAMMER STRUT SPRING
OUTER RECOIL SPRING
199-0103-168
(LARGE)
INNER RECOIL SPRING
199-0103-169
(SMALL)
OUTER BARREL
199-0103-211HK
THREADED
199-0103-227 front sight
199-0103-232 Rear Sight Base Plate
199-0103-233 Rear Sight
199-0103-234 Rear Sight Blade
Trigger Over Travel
199-0103-236
Adjustment Screw
Rear sight Windage
199-0103-237
screw
Rear sight Windage
199-0103-238
screw Nut
Rear Sight Elevation
199-0103-239
screw
Rear Sight Windage
199-0103-240
Pin
Rear Sight Windage
199-0103-241
spring
199-0103-243 Trigger
199-0103-244 Outer Barrel O-Ring
199-0103-254 Safety Lever “Right”
199-0103-255 Safety Lever “Left”
safety lever set
199-0103-256
screw “Right”
199-0103-257 Rear Sight Plunger x 2
Rear Sight Plunger
199-0103-258
Spring x 2
H&K USP TACTICAL MAGAZINE DIAGRAM AND PARTS LIST
110
196
102
111
103
107
108
113
198
194
200
100
203
105
201
195
Parts #
Description
199-0103-100
MAGAZINE BASE PLATE LOCK
199-0103-102
MAGAZINE FOLLOWER
199-0103-103
MAGAZINE NOZZLE SEAL
199-0103-105
MAGAZINE BASE LOCK PIN “SMALL”
199-0103-107
MAGAZINE LIP PINS X 2
199-0103-108
MAGAZINE FOLLOWER SPRING
199-0103-110
MAGAZINE FOLLOWER LOCK SPRING
199-0103-111
MAGAZINE FOLLOWER LOCK
199-0103-112
MAGAZINE CHARGING VALVE
199-0103-113
MAGAZINE RELEASE VALVE
199-0103-194
MAGAZINE BODY
199-0103-195
MAGAZINE BASE
199-0103-196
MAGAZINE LIP
199-0103-198
MAGAZINE BASE PLATE
199-0103-200
MAGAZINE EXPANSION TUBE
199-0103-201
MAGAZINE BASE PINS X 2
199-0103-203
MAGAZINE BASE SEAL
112
38
H&K USP SERIES
H&K USP MATCH PARTS DIAGRAM
244
235
225HK
143
228
144
248
36
116
245
13
12
126
248
121
37
245
149
120
145
45
168
229
151
169
124
150
155
230
129HK
246
17
256
72
254
85
242
32
226
82
134
125
89
231
255
152
39
247
H&K USP MATCH PARTS DIAGRAM
239
227
135
92
92
258
257
130HK
233
8
241
91
48
7
232
240
117
49
38
153
11
15
75
95
74
249
162
122
27
30
84
68
52
25
24
163
26
118
28
23
138
69
69
164
123
80
71
83
88
167
44
87
243
139
29
236
65
70
51
86
40
H&K USP SERIES
H&K USP MATCH PARTS LIST
Parts #
Description
Parts #
Description
199-0103-7
JET NOZZLE
199-0103-87
TRIGGER SPRING
199-0103-8
EXTRACTOR
199-0103-11
INNER BARREL RETAINING
RING
199-0103-88
TRIGGER BAR PLUNGER
SPRING
199-0103-89
MAGAZINE CATCH SPRING
199-0103-226
Main Spring Housing
199-0103-12
HOP-UP CYLINDER
199-0103-91
JET NOZZLE SPRING
199-0103-227
FRONT SIGHT
199-0103-13
HOP-UP CYLINDER
CLAMP
199-0103-92
CYLINDER RETURN
SPRINGS x 2
199-0103-228
Barrel Weight “Left”
199-0103-15
BREACH
199-0103-229
Barrel Weight “Right”
199-0103-95
FIRING PIN SPRING
199-0103-17
SAFETY LEVER SLEEVE
199-0103-116
BARREL CLAMP SCREW
199-0103-230
Right Slide lock
release
199-0103-23
LEFT SEAR
199-0103-117
MAIN SEAL CAP SCREW
199-0103-231
Magazine Guide
199-0103-24
RIGHT SEAR
199-0103-118
INNER FRAME SCREW
199-0103-232
Rear Sight Base Plate
199-0103-25
IMPACT BLOCK BASE
199-0103-120
FEED RAMP SCREW
199-0103-233
Rear Sight
199-0103-26
IMPACT BLOCK BAR
Inner Barrel
IMPACT BLOCK
199-0103-121
199-0103-235
199-0103-27
RECOIL SPRING
RETAINING CLIP
199-0103-28
RESET LEVER
199-0103-122
IMPACT BLOCK RETAINER
199-0103-236
Trigger Over Travel
Screw
199-0103-29
SAFETY LEVER PLATE
199-0103-123
IMPACT BLOCK BASE PIN
199-0103-237
199-0103-124
RECOIL SPRING DIVIDER
PIN
REAR SIGHT WINDAGE
SCREW
199-0103-238
199-0103-125
MAGAZINE CATCH ROLL
PIN
REAR SIGHT WINDAGE
SCREW NUT
199-0103-126
HOP-UP BALL BEARING
199-0103-239
Elevation adjustment
screw
199-0103-240
REAR SIGHT WINDAGE
Pin
199-0103-241
REAR SIGHT WINDAGE
spring
199-0103-30
SAFETY LEVER RETAINER
199-0103-32
MAGAZINE CATCH
199-0103-36
BB FEED RAMP
199-0103-37
HOP-UP BUCKING
199-0103-38
MAIN SEAL
199-0103-44
TRIGGER PIN SLEEVE
199-0103-45
INNER BARREL BASE PIN
199-0103-48
JET NOZZLE PIN
199-0103-49
MAIN SEAL CAP
199-0103-51
SAFETY LEVER BAR
199-0103-52
RIGHT SEAR PLATE
199-0103-65
IMPACT BLOCK
EXTENSION
199-0103-68
IMPACT BLOCK PIN
199-0103-69
PLUNGER X2
199-0103-70
HAMMER STRUT PIN
199-0103-71
SEAR PIN
199-0103-150
199-0103-72
TRIGGER PIN
199-0103-74
FIRING PIN
199-0103-75
PISTON BASE SCREW
199-0103-80
199-0103-129HK FRAME
Parts #
Description
199-0103-169
INNER RECOIL SPRING
(SMALL)
199-0103-225HK Outer Barrel
199-0103-130HK SLIDE
199-0103-134
HAMMER STRUT LOCK
199-0103-135
CYLINDER
199-0103-138
INNER FRAME
199-0103-242
Slide Catch Lever
“Left”
199-0103-139
HAMMER
199-0103-244
Barrel O-Ring
199-0103-143
INNER BARREL HOUSING
199-0103-144
INNER BARREL CLAMP
199-0103-245
Barrel Weight
Washers X 2
199-0103-145
INNER BARREL BASE
199-0103-246
Slide Stop Lever
“Right” screw
199-0103-149
RECOIL SPRING SPACER
(LARGE)
199-0103-247
Magazine Guide Screw
RECOIL SPRING SPACER
(SMALL)
199-0103-248
Barrel Weight Screws x 2
199-0103-249
breach screw
199-0103-151
RECOIL SPRING DIVIDER
199-0103-254
SAFETY LEVER “RIGHT”
199-0103-152
MAIN SPRING HOUSING
PIN
199-0103-255
SAFETY LEVER “LEFT”
SEAR SPRING
199-0103-153
MAIN SEAL BASE
199-0103-256
SAFETY LEVER SET
SCREW “RIGHT”
199-0103-82
HAMMER STRUT
LOCKING PIN
199-0103-155
RECOIL SPRING GUIDE
199-0103-257
REAR SIGHT Plunger X2
199-0103-162
TRIGGER BAR
RESET LEVER PLUNGER
SPRING
199-0103-163
HAMMER STRUT
199-0103-258
199-0103-83
REAR SIGHT Plunger
Spring X2
199-0103-84
IMPACT BLOCK SPRING
199-0103-164
SERIAL NUMBER PLATE
199-0103-85
SLIDE STOP SPRING
199-0103-167
HAMMER STRUT SPRING
199-0103-86
SAFETY LEVER SPRING
199-0103-168
OUTER RECOIL SPRING
(LARGE)
41
H&K USP MATCH MAGAZINE DIAGRAM AND PARTS LIST
196
102
103
107
253
107
113
251
100
203
105
195
201
201
112
252
Parts #
Description
199-0103-100
MAGAZINE BASE PLATE LOCK
199-0103-102
MAGAZINE FOLLOWER
199-0103-103
MAGAZINE NOZZLE SEAL
199-0103-105
MAGAZINE BASE LOCK PIN “SMALL”
199-0103-107
MAGAZINE LIP PINS X 2
199-0103-112
MAGAZINE CHARGING VALVE
199-0103-113
MAGAZINE RELEASE VALVE
199-0103-195
MAGAZINE BASE
199-0103-196
MAGAZINE LIP
199-0103-201
MAGAZINE BASE PINS X 2
199-0103-203
MAGAZINE BASE SEAL
199-0103-251
MAGAZINE HOUSING
199-0103-252
MAGAZINE BASE PLATE
199-0103-253
MAGAZINE FOLLOWER SPRING
42
MMD02 V01 R2011.06.03
KWA Performance Industries, Inc.
18571 E. Gale Ave
City of Industry, CA 91748
T: 626.581.1777 • F: 626.581.0777
www.kwausa.com
Copyright © December, 2008 KWA Performance Industries, Inc. All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement