FCC Compliance Statement: This equipment has been tested and

FCC Compliance Statement: This equipment has been tested and
FCC Compliance Statement:
This equipment has been tested and found to
comply with limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable
protection against harmful interference in
residential installations. This equipment
generates, uses, and can radiate radio
frequency energy, and if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
Eric Lu
equipment does cause interference to radio or
television equipment reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2. 1077(a)
Responsible Party Name: G.B.T. INC.
Address: 18305 Valley Blvd., Suite#A
LA Puent, CA 91744
Phone/Fax No: (818) 854-9338/ (818) 854-9339
hereby declares that the product
Product Name: Mother Board
Model Number: GA-6OMM7
Conforms to the following specifications:
FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),
Class B Digital Device
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful
and (2) this device must accept any inference received, including
that may cause undesired operation.
Representative Person's Name:
ERIC LU
Signature:
Date:
Jun. 13, 2000
-Reorient or relocate the receiving antenna
-Move the equipment away from the receiver
-Plug the equipment into an outlet on a circuit different from that to which
the receiver is connected
-Consult the dealer or an experienced radio/television technician for
additional suggestions
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void Your
authority to operate such equipment.
This device complies with Part 15 of the FCC Rules. Operation is subjected to
the following two conditions 1) this device may not cause harmful interference
and 2) this device must accept any interference received, including interference
that may cause undesired operation.
Declaration of Conformity
We, Manufacturer/Importer
(full address)
G.B.T. Technology Träding GMbH
Ausschlager Weg 41, 1F, 20537 Hamburg, Germany
declare that the product
( description of the apparatus, system, installation to which it refers)
Mother Board
GA-6OMM7
is in conformity with
(reference to the specification under which conformity is declared)
in accordance with 89/336 EEC-EMC Directive
EN 55011
Limits and methods of measurement
of radio disturbance characteristics of
industrial, scientific and medical (ISM
high frequency equipment
EN 61000-3-2*
EN60555-2
Disturbances in supply systems caused
by household appliances and similar
electrical equipment “Harmonics”
EN55013
Limits and methods of measurement
of radio disturbance characteristics of
broadcast receivers and associated
equipment
EN61000-3-3*
EN60555-3
Disturbances in supply systems caused
by household appliances and similar
electrical equipment “Voltage fluctuations”
EN 55014
Limits and methods of measurement
of radio disturbance characteristics of
household electrical appliances,
portable tools and similar electrical
apparatus
EN 50081-1
Generic emission standard Part 1:
Residual, commercial and light industry
EN 50082-1
Generic immunity standard Part 1:
Residual, commercial and light industry
EN 55015
Limits and methods of measurement
of radio disturbance characteristics of
fluorescent lamps and luminaries
EN 55081-2
Generic emission standard Part 2:
Industrial environment
EN 55020
Immunity from radio interference of
broadcast receivers and associated
equipment
EN 55082-2
Generic immunity standard Part 2:
Industrial environment
EN 55022
Limits and methods of measurement
of radio disturbance characteristics of
information technology equipment
ENV 55104
Immunity requirements for household
appliances tools and similar apparatus
DIN VDE 0855
part 10
part 12
Cabled distribution systems; Equipment
for receiving and/or distribution from
sound and television signals
EN 50091- 2
EMC requirements for uninterruptible
power systems (UPS)
CE marking
(EC conformity marking)
The manufacturer also declares the conformity of above mentioned product
with the actual required safety standards in accordance with LVD 73/23 EEC
EN 60065
Safety requirements for mains operated
electronic and related apparatus for
household and similar general use
EN 60950
Safety for information technology equipment
including electrical business equipment
EN 60335
Safety of household and similar
electrical appliances
EN 50091-1
General and Safety requirements for
uninterruptible power systems (UPS)
Manufacturer/Importer
Signature :
(Stamp)
Date: Jun. 13, 2000
Name
:
Rex Lin
Rex Lin
6OMM7
Socket 370 Processor Motherboard
USER'S MANUAL
Socket 370 Processor Motherboard
REV. 1.2 Third Edition
R-12-03-000727
How This Manual Is Organized
This manual is divided into the following sections:
1) Revision History
Manual revision information
2) Item Checklist
Product item list
3) Features
Product information & specification
4) Hardware Setup
Instructions on setting up the motherboard
5) Performance & Block Diagram
Product performance & block diagram
6) Suspend to RAM
Instructions STR installation
7) BIOS Setup
Instructions on setting up the BIOS
software
8) Appendix
General reference
Table Of Content
Revision History
P.1
Item Checklist
P.2
Summary of Features
P.3
6OMM7 Motherboard Layout
P.5
Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition
P.6
Performance List
P.29
Block Diagram
P.30
Suspend to RAM Installation (Optional)
P.31
Memory Installation
P.37
Page Index for BIOS Setup
P.38
Appendix
P.73
6OMM7 Motherboard
Revision History
Revision
1.1
1.2
1.2
1.2
Revision Note
Initial release of the 6OMM7 motherboard user’s manual.
Initial release of the 6OMM7 motherboard user’s manual.
Second release of the 6OMM7 motherboard user’s manual.
Third release of the 6OMM7 motherboard user’s manual.
Date
May.2000
May.2000
Jun.2000
Jul.2000
The author assumes no responsibility for any errors or omissions that may appear in this
document nor does the author make a commitment to update the information contained herein.
Third-party brands and names are the property of their respective owners.
Jul. 27, 2000 Taipei, Taiwan, R.O.C
1
Item Checklist
Item Checklist
þThe 6OMM7 motherboard
þCable for IDE / floppy device
þDiskettes or CD (IUCD) for motherboard driver & utility
þ6OMM7 user’s manual
2
6OMM7 Motherboard
Summary Of Features
Form Factor
CPU
Ÿ
24.4 cm x 20.5 cm Micro ATX form factor, 4 layers PCB.
Ÿ
Socket 370 processor
Chipset
Ÿ
Intel Pentium!!! 100/133MHz FSB, FC-PGA
Intel CeleronTM 66MHz FSB, FC-PGA
Ÿ
Ÿ
Clock Generator
Ÿ
Ÿ
Memory
Ÿ
Ÿ
Ÿ
Ÿ
I/O Control
Slots
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
On-Board IDE
Ÿ
Ÿ
On-Board
Peripherals
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Hardware Monitor
Ÿ
Ÿ
Ÿ
Ÿ
On-Board Sound
Ÿ
Ÿ
2nd cache in CPU (Depend on CPU)
Intel 815 HOST / AGP / SDRAM Controller
82801AA I/O Controller Hub(ICH)
ICS 9250AF-25
66/100/133 MHz system bus speeds
3 168-pin DIMM sockets
Supports PC-100 / PC-133 SDRAM
Supports up to 512MB(Max)
Supports only 3.3V SDRAM DIMM
IT8712
1 AGP Slot Supports 4X mode & AGP 2.0 compliant
1 DFP /TV
3 PCI Slot Supports 33MHz & PCI 2.2 compliant
1 AMR (Audio Modem Riser)Slot
Supports PIO mode 3, 4, UDMA33/ATA66 IDE & ATAPI
CD-ROM
2 IDE bus master (UDMA 33/ ATA 66) IDE ports for up
to 4 ATAPI devices
1 floppy port supports 2 FDD with 360K, 720K, 1.2M,
1.44M and 2.88M bytes
1 parallel ports supports SPP/EPP/ECP mode
1 serial ports (COM A)
2 USB ports
1 IrDA connector for IR/CIR
CPU/Power Supply/System fan revolution detect
CPU temperature detect
System voltage detect
CPU overheat shutdown detect
AC’97 CODEC
Line In / Line Out / Mic In / AUX In / CD In / TEL /
Game Port
To be continued…
3
Summary of Features
PS/2 Connector
BIOS
Additional Features
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
PS/2 keyboard interface and PS/2 mouse interface
Licensed AWARD BIOS, 4M bit Flash ROM
Supports Wake-on-LAN (WOL)
Supports Internal / External modem wake up
Includes 3 fan power connectors
Poly fuse for keyboard over-current protection
4
6OMM7 Motherboard
6OMM7 Motherboard Layout
PS/2
JP3
LED1
JP1
USB
JP7
PGA 370
CPU
JP25
Floppy
JP5
6OMM7
FW82815
BAT1
JP27
AGP
J10
DFP/TV
AC’97
JP12
PCI1
BZ1
J12
J7
JP13
J13
ICH82801
PCI2
J6
JP14
J5
JP15
JP20
FWH
J11
PCI3
JP21
JP24
AMR
JP23
JP18
JP22
5
J14
6OMM7 Motherboard Layout
$
Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition
CPU Speed Setup
Connectors
Game & Audio Port
COM A / VGA / LPT Port
USB Connector
PS/2 Keyboard & PS/2 Mouse Connector
J1 (CPU Fan)
J2 (Power Fan)
J14 (System Fan)
ATX Power
JP13 (IR/CIR)
Floppy Port
IDE 1(Primary)/ IDE 2(Secondary) Port
J13 (Ring Power On)
J12 (Wake on LAN)
J7 (TEL)
J6 (AUX_IN)
J5 (CD Audio Line In)
JP7 (STR LED Connector) & LED 1 (DIMM LED)[Optional]
Front USB Port (Optional)
J10 (Extra SMBUS)
JP25 (USB Port Selection) [Optional]
DFP/TV Out Connector
JP27 (SCR)
Panel and Jumper Definition
J11 (2x11 Pins Jumper)
JP18 (Clear CMOS Function)
JP4 (STR Enable) [Optional]
JP3 (PS/2 Keyboard Power On)
JP22 (Case Open)
JP1 (Rear USB Device Wake up Selection)
JP20 (FWH Flash Write Protect)
JP21 (Top Block Lock)
JP5 (Over Voltage CPU Speed Up)
JP6 (DIMM Over Voltage) [Optional]
JP12 (Internal Buzzer) [Optional]
6
Page
P.8
P.9
P.9
P.9
P.10
P.10
P.11
P.11
P.12
P.12
P.13
P.13
P.14
P.14
P.15
P.15
P.16
P.16
P.17
P.17
P.18
P.18
P.19
P.19
P.20
P.20
P.21
P.21
P.22
P.22
P.23
P.23
P.24
P.24
P.25
P.25
6OMM7 Motherboard
JP14 (Timeout Reboot Function)
P.26
7
6OMM7 Motherboard Layout
JP15 (Safe mode/Recovery/Normal)
JP23 (PCI/AGP 3VAUX)
JP24 (AMR Selection) [Optional]
BAT1 (Battery)
P.26
P.27
P.27
P.28
8
CPU Speed Setup
CPU Speed Setup
The system bus frequency can be switched at 66MHz, 100MHz, 133MHz and Auto by adjusting
JP10/JP11/JP26 (See Figure 1). The CPU Frequency is control by BIOS.
M The CPU speed must match with the frequency RATIO. It will cause system hanging
up if the frequency RATIO is higher than that of CPU.
JP10/JP11/JP26: CPU Speed Setup
1
1
1
JP10
JP26
JP11
CPU SDRAM JP10 JP11 JP26
Auto Auto
1-2
1-2
1-2
66
100
2-3
2-3
1-2
100
100
2-3 Open 1-2
133
133
Open 2-3
1-2
133
100
Open Open 2-3
Auto Configuration:
CPU
SDRAM
66
100
100
100
133
Ö133/100
Figure 1
Ö If the CPU FSB is 133 FSB, the frequency of the SDRAM can be determined by
SDRAM’s SPD or setting in BIOS.
M If JP10, JP11, JP25 is not present, FSB will be determined automatically. If these 3
jumpers are available, you can choose at 66MHz, 100MHz, 133MHz and Auto.
MNote: Please set the CPU host frequency in accordance with your processor’s
specifications. We don’t recommend you to set the system bus frequency over
the CPU’s specification because these specific bus frequencies are not the
standard specifications for CPU, chipset and most of the peripherals. Whether
your system can run under these specific bus frequencies properly will depend
on your hardware configurations, including CPU, Chipsets, SDRAM,
Cards… .etc.
9
6OMM7 Motherboard
Connectors
Game & Audio Port
Game
Port
MIC In
Line Out
Line In
COM A / VGA / LPT Port
LPT Port
COM A
10
VGA
6OMM7 Motherboard
USB Connector
Pin No.
1
2
3
4
5
6
7
8
5 6 7 8
1 23 4
Definition
USB V0
USB D0USB D0+
GND
USB V1
USB D1USB D1+
GND
PS/2 Keyboard & PS/2 Mouse Connector
PS/2 Mouse
5
6
4
3
2
1
PS/2 Keyboard
PS/2 Mouse/ Keyboard
Pin No.
Definition
1
Data
2
NC
3
GND
4
VCC(+5V)
5
Clock
6
NC
11
Connectors
J1: CPU Fan
1
Pin No. Definition
1
GND
2
+12V
3
SENSE
J2: Power Fan
1
Pin No. Definition
1
GND
2
+12V
3
SENSE
12
6OMM7 Motherboard
J14: System Fan
1
Pin No. Definition
1
GND
2
+12V
3
SENSE
ATX Power
Pin No.
Definition
3,5,7,13,15-17
GND
1,2,11
3.3V
4,6,19,20
VCC
10
+12V
12
-12V
18
-5V
8
Power Good
9
5V SB stand by+5V
14
PS-ON(Soft On/Off)
10 20
1 11
13
Connectors
JP13: IR/CIR
1
6
5
10
Pin No.
1
2
3
4
5
6
7
8
9
10
Floppy Port
Red Line
14
Definition
VCC
NC
IRRX
GND
IRTX
NC
CIRRX
VCC
NC
NC
6OMM7 Motherboard
IDE1 (Primary), IDE2 (Secondary) Port
IDE 2 IDE 1
Red Line
J13: Ring Power On (Internal Modem Card Wake Up)
1
Pin No.
1
2
15
Definition
Signal
GND
Connectors
J12: Wake On LAN
1
Pin No. Definition
1
+5V SB
2
GND
3
Signal
J7: TEL: The connector is for Modem with internal voice connector
1
Pin No. Definition
1
Signal-In
2
GND
3
GND
4
Signal-Out
16
6OMM7 Motherboard
J6: AUX_IN
Pin No.
1
2
3
4
1
Definition
AUX-L
GND
GND
AUX-R
J5: CD Audio Line In
Pin No.
1
2
3
4
17
1
Definition
CD-L
GND
GND
CD-R
Connectors
JP7: STR LED Connector & LED1: DIMM LED (Optional)
+
DIMM LED
1
STR LED Connector External
Front USB Port (Optional)
1
2
9
10
Pin No.
1,4,5,10
2
3,7,9
6
8
18
Definition
NC
+5V
GND
USBP0+
USBP0-
6OMM7 Motherboard
J10: Extra SMBUS
Pin No.
1
2
3
4
5
1
Definition
SMB CLK
NC
GND
SMB DATA
+5V
JP25: USB Port Selection (Optional)
1
4
3
6
Front Panel USB Enable Back Panel USB Enable
FPUSB
BPUSB(Default)
1-2close
2-3close
4-5close
5-6close
19
Connectors
DFP/TV Out Connector
íUse only for Gigabyte Digital Flat Panel/TV-Out Daughter card (GA-DFP-x).
27
1
2
28
JP27: SCR: Smart Card Reader
2
14
1
13
Pin No.
1
2,3,4,8,13
5,6,10,12
7
9,14
11
20
Definition
VCC
NC
DATA
Clock
NC
GND
Panel and Jumper Definition
Panel And Jumper Definition
J11: For 2x11 Pins Jumper
1
1
1
GD
RE
PW
P+ P− P− HD
1
GN (Green Switch)
GD (Green LED)
HD (IDE Hard Disk Active LED)
SPK (Speaker Connector)
RE (Reset Switch)
P+P−P−(Power LED)
PW (Soft Power Connector)
1
Open: Normal Operation
Close: Entering Green Mode
Pin 1: LED anode(+)
Pin 2: LED cathode(−)
Pin 1: LED anode(+)
Pin 2: LED cathode(−)
Pin 1: VCC(+)
Pin 2- Pin 3: NC
Pin 4: Data(−)
Open: Normal Operation
Close: Reset Hardware System
Pin 1: LED anode(+)
Pin 2: LED cathode(−)
Pin 3: LED cathode(−)
Open: Normal Operation
Close: Power On/Off
21
Panel and Jumper Definition
22
6OMM7 Motherboard
JP18: Clear CMOS Function
1
Pin No.
Definition
1-2 close
Clear CMOS
2-3 close Normal (Default)
JP4: STR Enable (Optional)
1
Pin No.
Definition
Open STR Disabled (Default)
Close
STR Enabled
23
Panel and Jumper Definition
JP3: PS/2 Keyboard Power On
1
Pin No.
Definition
1-2 close PS/2 Keyboard
Power on Enabled
2-3 close Normal (Default)
JP22: Case Open
1
Pin No. Definition
1
Signal
2
GND
24
6OMM7 Motherboard
JP1: Rear USB Device Wake up Selection (USB Connector à CN2)
1
Pin No.
Definition
Enabled Rear USB Device
1-2 close
Wake up
2-3 close Normal (Default)
CN2
(If you want to use “USB KB/Mouse Wake from S3”
function, you have to set the BIOS setting “USB KB/Mouse
Wake from S3” enabled, and the jumper “JP1” enabled).
*(Power on the computer and as soon as memory counting
starts, press <Del>. You will enter BIOS Setup. Select the
item “POWER MANAGEMENT SETUP”, then select “USB
KB/Mouse Wake from S3: Enabled”. Remember to save
the setting by pressing "ESC" and choose the “SAVE & EXIT
SETUP” option.)
JP20: FWH Flash Write Protect
1
Pin No.
Open
Close
Definition
Normal (Default)
Write Protection
MPlease set Jumper JP20 to “Open”
to enabled BIOS write function when
you update new BIOS or new device.
25
Panel and Jumper Definition
JP21: Top Block Lock
1
Pin No.
Definition
Open Top Block Lock
Close Top Block Unlock (Default)
JP5: Over Voltage CPU Speed Up (Magic Booster)
(When JP5 set “Close”, CPU Voltage is rising 10%)
1
Pin No.
Definition
Close Turbo
[Voltage enhance 10%]
for over clock use
Open Normal (Default)
26
6OMM7 Motherboard
JP6: DIMM Over Voltage (Optional)
1
Pin No.
Definition
Close Enabled DIMM Over Voltage
Open Disabled DIMM Over Voltage
(Default)
JP12: Internal Buzzer (Optional)
1
Pin No.
Definition
Open Internal Buzzer Disabled
Close Internal Buzzer Enabled
(Default)
27
Panel and Jumper Definition
JP14: Timeout Reboot Function
1
Pin No.
Definition
Open Timeout Reboot
Close No Reboot on Timeout
JP15: Safe mode/Recovery/Normal
1
Pin No.
Definition
1-2close Normal (Default)
2-3close
Safe mode
1-2-3open
Recovery
28
6OMM7 Motherboard
JP23: PCI/AGP 3VAUX
1
Pin No.
Definition
Open Disabled PCI/AGP 3VAUX
Function
Close Enabled PCI/AGP 3VAUX
(Default)
JP24: AMR Selection (Optional)
1
Pin No.
Definition
1-2close AMR Secondary
AMR Primary
2-3close AC’97 Disabled (Default)
(Disabled Onboard CODEC)
29
Panel and Jumper Definition
BAT1: Battery
+
+ Danger of explosion if battery
is incorrectly replaced.
+ Replace only with the same or
equivalent type recommended
by the manufacturer.
+ Dispose of used batteries
according to the manufacturer’s
instructions.
30
6OMM7 Motherboard
Performance List
The following performance data list is the testing results of some popular benchmark testing
programs.
These data are just referred by users, and there is no responsibility for different testing data
values gotten by users. (The different Hardware & Software configuration will result in different
benchmark testing results.)
• CPU
• DRAM
• CACHE SIZE
• DISPLAY
• STORAGE
• O.S.
• DRIVER
Intel® Pentium® !!! Socket 370 Processor
(128 x 1) MB SDRAM (MOSEL 9928PR V54C365804VCT7)
256 KB included in CPU
GA-660 Plus AGP Card, Onboard VGA, Onboard VGA&GA-AIMM
Onboard IDE (Quantum KA13600AT)
Windows NT™4.0 (SP6a)
Display Driver at 1024 x 768 x 16bit x 75Hz
Intel Pentium !!!
Processor
Display
933MHz (133X7)
Onboard
Onboard & GA –AIMM
GA-660 Plus
Winbench99
CPU mark99
80.5
80.3
83
FPU Winmark 99
4900
4970
4960
Business Disk Winmark 99
5450
5450
5640
12000
12900
12900
Business Graphics Winmark 99
106
132
448
Hi-End Graphics Winmark 99
581
634
875
Hi-End Disk Winmark 99
Winstone99
Business Winstone99
35.8
40.6
46.3
Hi-End Winstone99
48.3
49.1
48.2
M If you wish to maximize the performance of your system, please refer to the detail on P.50
31
Block Diagram
Block Diagram
Socket 370
66/100/133 MHz
AGP
2X/4X
Display
Host Bus 66/100/133MHz
66/100/133 MHz
Intel
FW82815
3.3V SDRAM
100 MHz
Hub
SDRAM
SDRAM
Display Cache
Interface
14.318/33/48/66 MHz
PCI Bus 33MHz
ICH
82801AA
ATA66 IDE Channels
DFP/TV
AC’ 97 Link
2 USB Ports
COM Port
FWH
Game Port
AC’97
LPT Ports
IT8712
SMART Card
Reader
IR Floppy
PS/2
30
ICS
9250AF-25
3 PCI
6OMM7 Motherboard
Suspend To RAM Installation (Optional)
A.1 Introduce STR function:
Suspend-to-RAM (STR) is a Windows 98 ACPI sleep mode function. When recovering from
STR (S3) sleep mode, the system is able, in just a few seconds, to retrieve the last “state” of
the system before it went to sleep and recover to that state. The “state” is stored in memory
(RAM) before the system goes to sleep. During STR sleep mode, your system uses only
enough energy to maintain critical information and system functions, primarily the system state
and the ability to recognize various “wake up” triggers or signals, respectively.
A.2 STR function Installation
Please use the following steps to complete the STR function installation.
Step-By-Step Setup
Step 1:
To utilize the STR function, the system must be in Windows 98 ACPI mode.
Putting Windows 98 into ACPI mode is fairly easy.
Setup with Windows 98 CD:
A.
Insert the Windows 98 CD into your CD-ROM drive, select Start, and then Run.
B.
Type (without quotes) “D:\setup /p j” in the window provided. Hit the enter key or click
OK.¡ y
In Windows 98 second edition version, all the bios version dated 12/01/99 or later
are ACPI compatible. Just type" D:\Setup", the operating system will be installed as
ACPI mode.¡ z
C.
After setup completes, remove the CD, and reboot your system
(This manual assumes that your CD-ROM device drive letter is D:).
31
Suspend to RAM Installation
Step 2:
(If you want to use STR Function, please set jumper JP4 Closed.)
1
Definition
Pin No.
Open STR Disabled (Default)
Close
STR Enabled
Step 3:
Power on the computer and as soon as memory counting starts, press <Del>. You will enter
BIOS Setup. Select the item “POWER MANAGEMENT SETUP”, then select “ACPI
Suspend Type: S3(Suspend to RAM)”. Remember to save the settings by pressing "ESC"
and choose the “SAVE & EXIT SETUP” option.
Congratulation! You have completed the installation and now can use the STR function.
32
6OMM7 Motherboard
A.3 How to put your system into STR mode?
There are two ways to accomplish this:
1.
Choose the “Stand by” item in the “Shut Down Windows” area.
A. Press the “Start” button and then select “Shut Down”
B. Choose the “Stand by” item and press “OK”
33
Suspend to RAM Installation
2.
Define the system ”power on” button to initiate STR sleep mode:
A. Double click “My Computer” and then “Control Panel”
B. Double click the “ Power Management” item.
34
6OMM7 Motherboard
C. Select the “Advanced” tab and “Standby” mode in Power Buttons.
Step 4:
Restart your computer to complete setup.
Now when you want to enter STR sleep mode, just momentarily press the “Power on”
button..
A.4 How to recover from the STR sleep mode?
There are seven ways to “wake up” the system:
1. Press the “Power On” button.
2. Use the “PS/2 Keyboard Power On” function.
3. Use the “Mouse Power On” function.
4. Use the “Resume by Alarm” function.
5. Use the “Modem Ring On” function.
6. Use the “Wake On LAN” function.
7. Use the “USB Device Wake up” function.
35
Suspend to RAM Installation
A.5 Notices:
1.
In order for STR to function properly, several hardware and software requirements must be
satisfied:
A. Your ATX power supply must comply with the ATX 2.01 specification (provide more than
720 mA 5V Stand-By current).
B. Your SDRAM must be PC-100 compliant.
2. Jumper JP7 is provided to connect to the STR LED in your system chassis. [Your chassis
may
not provide this feature.] The STR LED will be illuminated when your system is in STR sleep
mode.
+
DIMM LED
1
STR LED Connector External
36
6OMM7 Motherboard
Memory Installation
The motherboard has 3 dual inline memory module (DIMM) sockets. The BIOS will automatically
detects memory type and size. To install the memory module, just push it vertically into the DIMM
Slot .The DIMM module can only fit in one direction due to the two notch. Memory size can vary
between sockets.
Install memory in any combination table:
DIMM
DIMM1
DIMM2
DIMM3
168-pin SDRAM DIMM Modules
Supports 16 / 32 / 64 / 128 / 256 / 512MB
Supports 16 / 32 / 64 / 128 / 256 / 512MB
Supports 16 / 32 / 64 / 128 / 256 / 512MB
37
X 1 pcs
X 1 pcs
X 1 pcs
BIOS Setup
$ Page Index for BIOS Setup
Main Menu
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/ PCI Configurations
PC Health Status
Frequency / Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor / User Password
Save & Exit Setup
EXIT Without Saving
Page
P.40
P.43
P.47
P.50
P.53
P.59
P.63
P.65
P.67
P.68
P.69
P.70
P.71
P.72
38
6OMM7 Motherboard
BIOS Setup
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify
the basic system configuration. This type of information is stored in battery-backed CMOS RAM
so that it retains the Setup information when the power is turned off.
ENTERING SETUP
Power ON the computer and press <Del> immediately will allow you to enter Setup. If the
message disappears before you respond and you still wish to enter Setup, restart the system to
try again by turning it OFF then ON or pressing the "RESET" bottom on the system case. You
may also restart by simultaneously press <Ctrl> − <Alt>− <Del> keys.
CONTROL KEYS
<↑>
<↓>
<←>
<→>
<Esc>
<+/PgUp>
<-/PgDn>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
Move to previous item
Move to next item
Move to the item in the left hand
Move to the item in the right hand
Main Menu - Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu - Exit current page
and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option Page Setup
Menu
Reserved
Reserved
Reserved
Restore the previous CMOS value from CMOS, only for Option Page Setup
Menu
Load the default CMOS value from BIOS default table, only for Option Page
Setup Menu
Load the Optimized Defaults
Reserved
Reserved
Save all the CMOS changes, only for Main Menu
39
BIOS Setup
GETTING HELP
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item. To exit the Help Window press <Esc>.
The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 2) will appear on the
screen. The Main Menu allows you to select from nine setup functions and two exit choices. Use
arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
4Standard CMOS Features
4Frequency/Voltage Control
4Advanced BIOS Features
Load Fail-Safe Defaults
4Advanced Chipset Features
Load Optimized Defaults
4Integrated Peripherals
Set Supervisor Password
4Power Management Setup
Set User Password
4PnP/PCI Configurations
Save & Exit Setup
4PC Health Status
Exit Without Saving
ESC:Quit
F10:Save & Exit Setup
↑↓→ ← : Select Item
Time, Date, Hard Disk Type…
Figure 2: Main Menu
40
6OMM7 Motherboard
•
Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
•
Advanced BIOS Features
This setup page includes all the items of Award special enhanced features.
•
Advanced Chipset Features
This setup page includes all the items of chipset special features.
•
Integrated Peripherals
This setup page includes all onboard peripherals.
•
Power Management Setup
This setup page includes all the items of Green function features.
•
PnP/PCI Configurations
This setup page includes all the configurations of PCI & PnP ISA resources.
•
PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
•
Frequency/Voltage Control
This setup page is control CPU’ s clock and frequency ratio.
•
Load Fail-Safe Defaults
Fail-Safe Defaults indicates the value of the system parameters which the system would
be in safe configuration.
•
Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would
be in best performance configuration.
•
Set Supervisor password
Change, set, or disable password. It allows you to limit access to the system and Setup,
or just to Setup.
•
Set User password
Change, set, or disable password. It allows you to limit access to the system.
41
BIOS Setup
42
6OMM7 Motherboard
•
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
•
Exit Without Saving
Abandon all CMOS value changes and exit setup.
43
Standard CMOS F
res
includes no, one or more than one setup items. Use the arrows to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in e
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Mon , Feb 21 2000
Item Help
Time (hh:mm:ss)
2 : 31 : 24
Menu Level 4
4IDE Primary Master
Press Enter None
Change the
4IDE Primary Slave
Press Enter None
Day, month,
4IDE Secondary Master
Press Enter None
Year and
4IDE Secondary Slave
Press Enter None
century
Drive A
1.44M, 3.5 in.
Drive B
None
Floppy 3 Mode Support
Disabled
Video
Halt On
EGA / VGA
All, But Keyboard
Base Memory
Extended Memory
Total Memory
640K
63488K
64512K
↑↓→ ←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
•
Date
The date format is <week>, <month> <day> <year>.
The week, from Sun to Sat, determined by the BIOS and is display only
Month
Day
Year
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1994 through 2079
44
6OMM7 Motherboard
•
Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00.
•
IDE Primary Master, Slave / Secondary Master, Slave
The category identifies the types of hard disk from drive C to F that has been installed in the
computer. There are two types: auto type, and manual type. Manual type is user-definable;
Auto type which will automatically detect HDD type.
Note that the specifications of your drive must match with the drive table. The hard disk will
not work properly if you enter improper information for this category.
If you select User Type, related information will be asked to enter to the following items.
Enter the information directly from the keyboard and press <Enter>. Such information
should be provided in the documentation form your hard disk vendor or the system
manufacturer.
CYLS.
Number of cylinders
HEADS
number of heads
PRECOMP
write precomp
LANDZONE
Landing zone
SECTORS
number of sectors
If a hard disk has not been installed select NONE and press <Enter>.
•
Drive A type / Drive B type
The category identifies the types of floppy disk drive A or drive B that has been installed in
the computer.
None
360K, 5.25 in.
1.2M, 5.25 in.
720K, 3.5 in.
1.44M, 3.5 in.
2.88M, 3.5 in.
No floppy drive installed
5.25 inch PC-type standard drive; 360K byte capacity.
5.25 inch AT-type high-density drive; 1.2M byte capacity (3.5 inch
when 3 Mode is Enabled).
3.5 inch double-sided drive; 720K byte capacity
3.5 inch double-sided drive; 1.44M byte capacity.
3.5 inch double-sided drive; 2.88M byte capacity.
45
BIOS Setup
•
Floppy 3 Mode Support (for Japan Area)
Disabled
Drive A
Drive B
Both
•
Normal Floppy Drive. (Default value)
Drive A is 3 mode Floppy Drive.
Drive B is 3 mode Floppy Drive.
Drive A & B are 3 mode Floppy Drives.
Video
The category detects the type of adapter used for the primary system monitor that must
match your video display card and monitor. Although secondary monitors are supported,
you do not have to select the type in setup.
EGA/VGA
CGA 40
CGA 80
MONO
•
Enhanced Graphics Adapter/Video Graphics Array. For EGA, VGA,
SVGA, or PGA monitor adapters
Color Graphics Adapter, power up in 40 column mode
Color Graphics Adapter, power up in 80 column mode
Monochrome adapter, includes high resolution monochrome adapters
Halt on
The category determines whether the computer will stop if an error is detected during power
up.
NO Errors
All Errors
All, But Keyboard
All, But Diskette
All, But Disk/Key
The system boot will not stop for any error that may be detected
and you will be prompted.
Whenever the BIOS detects a non-fatal error the system will be
stopped.
The system boot will not stop for a keyboard error; it will stop for all
other errors. (Default value)
The system boot will not stop for a disk error; it will stop for all
other errors.
The system boot will not stop for a keyboard or disk error; it will
stop for all other errors.
46
6OMM7 Motherboard
•
Memory
is displayBIOS.
The POST of the BIOS will determine the amount of base (or conventional)
The value of the base memory is typically 512 K for systems
installed on the motherboard, or 640 K for systems with 640 K or more memory
installed on the motherboard.
Extended Memory
This is the amount of memory located abov
map.
BIOS Setup
Advanced BIOS Features
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
Advanced BIOS Features
Virus Warning
Disabled
Item Help
BIOS Flash Protection
Disabled
øProcessor Number Feature
Enabled
Menu Level 4
Allows you to
First Boot Device
Floppy
choose the VIRUS
Second Boot Device
HDD-0
Warning feature
Third Boot Device
LS120
For IDE Hard disk
Boot Up Floppy Seek
Enabled
Boot sector
Boot Up NumLock Status
On
Protection. If this
Security Option
Setup
Function is enable
HDD S.M.A.R.T. Capability
Disabled
And someone
Report No FDD For WIN 95
No
Attempt to write
Data into this area
, BIOS will show
A warning
Message on
Screen and alarm
beep
↑↓→ ←:Move Enter:Select +/ /PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:
-Safe Defaults F7:Optimized Defaults
Figure 4: Advanced BIOS Features
øSystem will detect automatically and show up when you install the Pentium® !!! processor.
•
Virus Warning
If it is set to enable, the category will flash on the screen when there is any attempt to write
to the boot sector or partition table of the hard disk drive. The system will halt and the
following error message will appear in the mean time. You can run anti-virus program to
locate the problem.
Enabled
Activate automatically when the system boots up causing a warning
message to appear when anything attempts to access the boot sector or
hard disk partition table.
No warning message to appear when anythi
boot sector or hard disk partition table. (Default value)
48
6OMM7 Motherboard
•
BIOS Flash Protection
Enabled
Disabled
•
Enabled BIOS Flash Protection.
Disabled BIOS Flash Protection. (Default Value)
Processor Number Feature
This item will show up when you install the Pentium® !!! processor.
Enabled
Disabled
•
First / Second / Third Boot device
Floppy
LS120
ZIP100
HDD-0~3
SCSI
CDROM
LAN
•
Pentium® !!! Processor Number Feature. (Default value)
Disable this function.
Select your boot device priority by Floppy.
Select your boot device priority by LS120.
Select your boot device priority by ZIP100.
Select your boot device priority by HDD-0~3.
Select your boot device priority by SCSI.
Select your boot device priority by CDROM.
Disable this function.
Select your boot device priority by LAN.
Boot Up Floppy Seek
type is 40 tracks 720
drive installed is 40 or 80 tracks. 360
M and 1.44 M are all 80 tracks.
BIOS searches for floppy disk drive to determine it is 40 or 80 tracks.
K, 1.2 M or 1.44
they are all 80 tracks.
BIOS will not search for the type of floppy disk drive by track number.
360
•
Boot Up NumLock Status
On
Off
Keypad is number keys. (Default value)
Keypad is arrow keys.
49
BIOS Setup
•
Security Option
This category allows you to limit access to the system and Setup, or just to Setup.
System
Setup
•
HDD S.M.A.R.T. Capability
Enabled
Disabled
•
The system can not boot and can not access to Setup page will be denied
if the correct password is not entered at the prompt.
The system will boot, but access to Setup will be denied if the correct
password is not entered at the prompt.
Enabled HDD S.M.A.R.T. Capability.
Disabled HDD S.M.A.R.T. Capability. (Default value)
Report No FDD For WIN 95
No
Yes
Assign IRQ6 For FDD. (Default value)
FDD Detect IRQ6 Automatically.
50
6OMM7 Motherboard
Advanced Chipset Features
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
Advanced Chipset Features
Top Performance
Disabled
Item Help
SDRAM Timing Control
Auto
ø SDRAM CAS Latency Time
3
Menu Level 4
ø SDRAM Cycle Time Tras/Trc
6/8
ø SDRAM RAS-to-CAS Delay
3
ø SDRAM RAS Precharge Time
3
Delayed Transaction
Enabled
On-Chip Video Window Size
64MB
AGP Graphics Aperture Size
64MB
Display Cache Frequency
133MHz
öSystem Memory Frequency
Auto
ÜOnboard Display Cache SettingÜ
♣Initial Display Cache
♣Display Cache Timing
Enabled
Auto
↑↓→ ←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 5: Advanced Chipset Features
ø These four items will be available when ”SDRAM Timing Control” is set to Manual.
öThis item will be show when the system bus frequency is 133MHz.
♣These two items will only be shown when you install GA-AIMM card.
• Top Performance
If you wish to maximize the performance of your system, set “Top Performance” as
“Enabled”.
Disabled
Enabled
•
SDRAM Timing Control
Auto
Manual
•
Disabled this function. (Default Value)
Enabled Top Performance function.
Set SDRAM Timing Control to Auto. (Default value)
Set SDRAM Timing Control to Manual.
SDRAM CAS latency Time
3
2
For Slower SDRAM DIMM module. (Default Value)
For Fastest SDRAM DIMM module.
51
•
6/8
5/7
•
SDRAM RAS- -CAS delay
3
2
•
Set SDRAM RAS Precharge Time to 3. (Default value)
Set SDRAM RAS Precharge Time to 2.
Delayed Transaction
Disabled
Enabled
•
-to CAS delay 3 SCLKs. (Default value)
Set SDRAM RAS-to-CAS delay 2 SCLKs.
SDRAM RAS Precharge Time
3
2
•
Set SDRAM Tras/Trc Cycle time is 6/8 SCLKs. (Default value)
Set SDRAM Tras/Trc Cycle time is 5/7 SCLKs.
On64MB
For slow speed ISA device in system. (Default value)
ndow Size
Set Graphics Aperture Size to 32MB.
Set Graphics Aperture Size to 64MB. (Default value)
• AGP Graphics Aperture Size
32 MB
64 MB
•
Display Cache Frequency
100MHz
133MHz
•
Set Display Cache Frequency to 100MHz.
Set Display Cache Frequency to 133MHz. (Default value)
System Memory Frequency
Auto
100MH
z
133MH
z
•
AGP Graphics Aperture Size is 32MB.
AGP Graphics Aperture Size is 64MB.
System Memory Frequency to Auto. (Default value)
Set System Memory Frequency to 100MHz.
Set System Memory Frequency to 133MHz.
Initial Display Cache
Disabled
Disabled Initial Display Cache.
52
6OMM7 Motherboard
Enabled
Enabled Initial Display Cache. (Default value)
53
BIOS Setup
•
Display Cache Timing
Auto
Fast
Normal
Set Display Cache Timing to Auto. (Default value)
Set Display Cache Timing to Fast.
Set Display Cache Timing to Normal.
54
6OMM7 Motherboard
Integrated Peripherals
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
Integrated Peripherals
On-Chip Primary PCI IDE
Enabled
Item Help
On-Chip Secondary PCI IDE
Enabled
IDE Primary Master PIO
Auto
Menu Level 4
IDE Primary Slave PIO
Auto
IDE Secondary Master PIO
Auto
IDE Secondary Slave PIO
Auto
IDE Primary Master UDMA
Auto
IDE Primary Slave UDMA
Auto
IDE Secondary Master UDMA
Auto
IDE Secondary Slave UDMA
Auto
USB Controller
Enabled
USB Keyboard Support
Disabled
USB Mouse Support
Disabled
Init Display First
PCI Slot
AC97 Audio
Auto
AC97 Modem
Auto
IDE HDD Block Mode
Enabled
POWER ON by Keyboard
Disabled
X KB Power ON Password
Enter
POWER ON by Mouse
Disabled
Onboard FDC Controller
Enabled
Onboard Serial Port 1
3F8/IRQ4
Onboard IR Port
2F8/IRQ3
UART Mode Select
IrDA
UR2 Duplex Mode
Half
Onboard Parallel Port
378/IRQ7
Parallel Port Mode
SPP
AC Back Function
Soft-Off
Game Port Address
201
Midi Port Address
330
Midi Port IRQ
10
↑↓→ ←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 6: Integrated Peripherals
•
On-Chip Primary PCI IDE
Enabled
Disabled
Enabled onboard 1st channel IDE port. (Default value)
Disabled onboard 1st channel IDE port.
55
BIOS Setup
•
On-Chip Secondary PCI IDE
Enabled
Disabled
•
IDE Primary Master PIO (for onboard IDE 1st channel)
Auto
Mode0~4
•
Mode0~4
Mode0~4
Mode0~4
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Manually set the IDE Accessing mode.
IDE Primary Master UDMA
Auto
Disabled
•
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Manually set the IDE Accessing mode.
IDE Secondary Slave PIO (for onboard IDE 2nd channel)
Auto
•
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Manually set the IDE Accessing mode.
IDE Secondary Master PIO (for onboard IDE 2nd channel)
Auto
•
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Manually set the IDE Accessing mode.
IDE Primary Slave PIO (for onboard IDE 1st channel)
Auto
•
Enabled onboard 2nd channel IDE port. (Default value)
Disabled onboard 2nd channel IDE port.
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Disable UDMA function.
IDE Primary Slave UDMA
Auto
Disabled
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Disable UDMA function.
56
6OMM7 Motherboard
•
IDE Secondary Master UDMA
Auto
Disabled
•
IDE Secondary Slave UDMA
Auto
Disabled
•
Enabled USB Keyboard Support.
Disabled USB Keyboard Support. (Default value)
USB Mouse Support
Enabled
Disabled
•
Enabled USB Controller. (Default value)
Disabled USB Controller.
USB Keyboard Support
Enabled
Disabled
•
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Disabled UDMA function.
USB Controller
Enabled
Disabled
•
BIOS will automatically detect the IDE HDD Accessing mode.
(Default value)
Disable UDMA function.
Enabled USB Mouse Support.
Disabled USB Mouse Support. (Default value)
Init Display First
Set Init Display First to PCI Slot. (Default value)
Set Init Display First to onboard/AGP.
PCI Slot
Onboard/AGP
•
AC97 Audio
Auto
Disabled
•
AC97 Modem
Auto
Disabled
•
BIOS will automatically detect onboard AC97 Audio or YAMAHA 744
audio. (Default value)
Disabled AC97 Audio.
Bios will automatically detect onboard AC97 Modem. (Default value)
Disabled AC97 Modem.
IDE HDD Block Mode
Enabled
Disabled
Enabled IDE HDD Block Mode. (Default value)
Disabled IDE HDD Block Mode.
57
BIOS Setup
•
POWER ON by Keyboard
Password
Enter from 1 to 5 characters to set the Keyboard Power On
Password.
Disabled this function. (Default value)
If your keyboard have “POWER Key” button, you can press the
key to power on your system.
Disabled
Keyboard 98
•
KB Power ON Password
Enter
•
Enter from 1 to 5 characters to set the Keyboard Power On Password.
POWER ON by Mouse
Mouse Click
Disabled
•
Onboard FDC Controller
Enabled
Disabled
•
Enabled onboard FDC port. (Default value)
Disabled onboard FDC port.
Onboard Serial Port 1
Auto
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
•
Double click on PS/2 mouse left button.
Disabled this function. (Default value)
BIOS will automatically setup the port 1 address.
Enabled onboard Serial port 1 and address is 3F8. (Default value)
Enabled onboard Serial port 1 and address is 2F8.
Enabled onboard Serial port 1 and address is 3E8.
Enabled onboard Serial port 1 and address is 2E8.
Disabled onboard Serial port 1.
Onboard IR Port
Auto
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Disabled
BIOS will automatically setup the IR Port address.
Enabled onboard IR Port and address is 3F8.
Enabled onboard IR Port and address is 2F8. (Default Value)
Enabled onboard IR Port and address is 3E8.
Enabled onboard IR Port and address is 2E8.
Disabled onboard IR Port.
58
6OMM7 Motherboard
•
UART Mode Select
(This item allows you to determine which Infra Red(IR) function of Onboard I/O chip)
ASKIR
Set onboard I/O chip UART to ASKIR Mode.
IrDA
Set onboard I/O chip UART to IrDA Mode. (Default Value)
SCR
Set onboard I/O chip UART to SCR Mode.
•
UR2 Duplex Mode
Half
Full
•
Onboard Parallel port
378/IRQ7
278/IRQ5
Disabled
3BC/IRQ7
•
This function depends on computer status.
Set System Soft-Off Status. (Default value)
Set System Full-On Status.
Game Port Address
Disabled
201
209
•
Using Parallel port as Standard Parallel Port. (Default Value)
Using Parallel port as Enhanced Parallel Port.
Using Parallel port as Extended Capabilities Port.
Using Parallel port as ECP & EPP mode.
AC Back Function
Memory
Soft-Off
Full-On
•
Enabled onboard LPT port and address is 378/IRQ7. (Default Value)
Enabled onboard LPT port and address is 278/IRQ5.
Disabled onboard LPT port.
Enabled onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP
EPP
ECP
ECP+EPP
•
IR Function Duplex Half. (Default Value)
IR Function Duplex Full.
Disabled this function.
Set onboard game port is 201. (Default Value)
Set onboard game port is 209.
Midi Port Address
Disabled
300
330
Disabled On Board Midi Port.
Set On Board Midi Port is 300.
Set On Board Midi Port is 330. (Default Value)
59
BIOS Setup
•
Midi Port IRQ
5
10
Set 5 for Midi Port IRQ.
Set 10 for Midi Port IRQ. (Default Value)
60
6OMM7 Motherboard
Power Management Setup
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
Power Management Setup
S1(PowerOn suspend)
ÜACPI Suspend Type
Item Help
Video Off Method
DPMS
Suspend Type
Stop Grant
Menu Level 4
MODEM Use IRQ
4
Suspend Mode
Disabled
HDD Power Down
Disabled
Soft-Off by PWR-BTTN
Instant-off
Power LED in Suspend
Blinking
Wake-Up by PCI card
Enabled
ModemRingOn/WakeOnLan
Enabled
ÜUSB KB/Mouse Wake From S3
Disabled
FAN Off In Suspend
Enabled
CPU Thermal-Throttling
50%
Resume by Alarm
Disabled
X Date(of Month) Alarm
Everyday
X Time(hh:mm:ss) Alarm
0 0 0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD,COM,LPT Port
PCI PIRQ[A-D]#
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
↑↓→ ←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 7: Power Management Setup
ÜThese two items will be shown when the system support STR function.
•
ACPI Suspend Type
S1(PowerOn Suspend)
S3(Suspend to RAM)
Set ACPI Suspend type to S1. (Default value)
Set ACPI Suspend type to S3.
61
BIOS Setup
•
Video off Method
V/H SYNC+Blank
BIOS will turn off V/H-SYNC when gets into Green mode for
Green monitor power saving.
BIOS will only black monitor when gets into Green mode.
BIOS will use DPMS Standard to control VGA card. (The Green
type VGA card will turn off V/H-SYNC automatically.)
(Default value)
Blank Screen
DPMS
•
Suspend Type
Set Suspend type is stop grant. (Default value)
Set Suspend type is Power on Suspend.
Stop Grant
PwrOn Suspend
•
MODEM Use IRQ
NA
3
4
5
7
9
10
11
•
Suspend Mode
Disabled
1 min - 1 Hour
•
Disabled Suspend Mode. (Default value)
Setup the timer to enter Suspend Mode.
HDD Power Down
Disabled
1-15 mins.
•
Set MODEM Use IRQ to NA.
Set MODEM Use IRQ to 3.
Set MODEM Use IRQ to 4. (Default value)
Set MODEM Use IRQ to 5.
Set MODEM Use IRQ to 7.
Set MODEM Use IRQ to 9.
Set MODEM Use IRQ to 10.
Set MODEM Use IRQ to 11.
Disabled HDD Power Down mode function. (Default value)
Enabled HDD Power Down mode between 1 to 15 mins.
Soft-off by PWR-BTTN
Instant-off
Delay 4 Sec.
Soft switch ON/OFF for POWER ON/OFF. (Default value)
Soft switch ON 4sec. for POWER OFF.
62
6OMM7 Motherboard
•
Power LED in Suspend
Blinking
On
Off/Dual
•
Wake-Up by PCI card
Disabled
Enabled
•
Disabled this function. (Default value)
Enabled USB KB/Mouse Wake From S3 function.
FAN Off In Suspend
Disabled
Enabled
•
Disabled these functions.
Enabled these functions. (Default value)
USB KB/Mouse Wake From S3
Disabled
Enabled
•
Disabled this function.
Enabled wake-up by PCI card. (Default value)
ModemRingOn / WakeOnLan
Disabled
Enabled
•
Set Power LED in Suspend at Blinking mode. (Default value)
Set Power LED in Suspend at On mode.
Set Power LED in Suspend at Off/Dual color mode.
Disabled this function.
Stop CPU FAN when entering Suspend mode. (Default value)
CPU Thermal-Throttling
87.5%
75.0%
62.5%
50.0%
37.5%
25.0%
12.5%
Monitor CPU Temp. will cause system
87.5%.
Monitor CPU Temp. will cause system
75.0%.
Monitor CPU Temp. will cause system
62.5%.
Monitor CPU Temp. will cause system
50.0%. (Default value)
Monitor CPU Temp. will cause system
37.5%.
Monitor CPU Temp. will cause system
25.0%.
Monitor CPU Temp. will cause system
12.5%.
63
slow down CPU Duty Cycle to
slow down CPU Duty Cycle to
slow down CPU Duty Cycle to
slow down CPU Duty Cycle to
slow down CPU Duty Cycle to
slow down CPU Duty Cycle to
slow down CPU Duty Cycle to
BIOS Setup
•
Resume by Alarm
You can set “Resume by Alarm” item to Enabled and key in date/time to power on system.
Disabled
Enabled
Disable this function. (Default value)
Enable alarm function to POWER ON system.
If the default value is Enabled.
Date ( of Month) Alarm :
Time ( hh: mm: ss) Alarm :
•
Primary IDE 0/1
Disabled
Enabled
•
Disabled this function. (Default value)
Enabled monitor Secondary IDE 0/1 for Green event.
FDD,COM,LPT Port
Disabled
Enabled
•
Disabled this function. (Default value)
Enabled monitor Primary IDE 0/1 for Green event.
Secondary IDE 0/1
Disabled
Enabled
•
Everyday, 1~31
(0~23) : (0~59) : (0~59)
Disabled this function. (Default value)
Enabled monitor FDC,COM,LPT for Green event.
PCI PIRQ[A-D] #
Enabled
Disabled
Monitor PCI PIRQ[A-D]# IRQ Active.
Ignore PCI PIRQ[A-D]# IRQ Active. (Default value)
64
6OMM7 Motherboard
PnP/PCI Configurations
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
PnP/PCI Configurations
Reset Configuration Data
Disabled
Item Help
Resources Controlled By
X IRQ Resources
PCI/VGA Palette Snoop
Auto (ESCD)
Press Enter
Disabled
Menu Level 4
When resources are
controlled manually,
assign each system
interrupt a type,
depending on the type
of device using the
interrupt
↑↓→ ←Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 8: PnP/PCI Configurations
•
Reset Configuration Data
Disabled
ESCD
DMI
Both
•
Resources Controlled by
Manual
Auto (ESCD)
•
Disabled this function. (Default value)
Clear PnP information in ESCD.
Update Desktop Management Information data.
Clear PnP information in ESCD & update DMI data.
User can set the PnP resource (I/O Address, IRQ & DMA channels)
used by legacy ISA DEVICE.
BIOS automatically use these PnP rescuers. (Default value)
IRQ ( 3,4,5,7,9,10,11,12,15 )
PCI Device
Reserved
The resource is used by PCI device.
Set the resource to reserved.
65
BIOS Setup
•
PCI/VGA Palette Snoop
Enabled
Disabled
For having Video Card on ISA Bus and VGA Card on PCI Bus.
For VGA Card only. (Default value)
66
6OMM7 Motherboard
PC Health Status
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
PC Health Status
Reset Case Open Status
Disabled
Item Help
Case Opened
No
VCORE
1.632 V
Menu Level 4
VGTL
1.424 V
VCC3
3.264 V
+ 5V
5.026 V
+12V
12.032 V
- 12V
-12.280 V
5VSB(V)
4.972 V
VBAT(V)
3.024 V
Current CPU Temperature
31°C
CPU FAN Speed
5443 RPM
Power FAN Speed
0 RPM
System FAN speed
0 RPM
CPU Temperature Select
80°C/176°F
Shutdown Temperature
Disabled
CPU FAN Fail Alarm
Disabled
Power FAN Fail Alarm
Disabled
System FAN Fail Alarm
Disabled
↑↓→ ←Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 9: PC Health Status
•
Reset Case Open Status
•
Case Opened
If the case is closed, “Case Opened” will show “No”.
If the case have been opened, “Case Opened” will show “Yes”.
If you want to reset “Case Opened” value, set “Reset Case Open Status” to “Enabled” and
save CMOS, your computer will restart.
•
Current Voltage (V) VCORE / VGTL/ VCC3 / ±12V / +5V / 5VSB / VBAT
Detect system’ s voltage status automatically.
•
Current CPU Temperature (°C / °F)
Detect CPU Temp. automatically.
67
BIOS Setup
•
CPU FAN / Power FAN / System FAN Speed (RPM)
Detect Fan speed status automatically.
• CPU Temperature Select (°C)
65°C / 149°F
70°C / 158°F
75°C / 167°F
80°C / 176°F
85°C / 185°F
90°C / 194°F
95°C / 203°F
Disabled
•
Monitor CPU Temp. at 65°C / 149°F.
Monitor CPU Temp. at 70°C / 158°F.
Monitor CPU Temp. at 75°C / 167°F.
Monitor CPU Temp. at 80°C / 176°F. (Default value)
Monitor CPU Temp. at 85°C / 185°F.
Monitor CPU Temp. at 90°C / 194°F.
Monitor CPU Temp. at 95°C / 203°F.
Disabled this function.
Shutdown Temperature (°C / °F)
(This function will be effective only for the operating systems that support ACPI Function.)
Disabled
65°C / 149°F
70°C / 158°F
75°C / 167°F
80°C / 176°F
85°C / 185°F
90°C / 194°F
95°C / 203°F
•
Normal Operation. (Default value)
Monitor CPU Temp. at 65°C / 149°F, if Temp. > 65°C / 149°F
system will automatically power off.
Monitor CPU Temp. at 70°C / 158°F, if Temp. > 70°C / 158°F
system will automatically power off.
Monitor CPU Temp. at 75°C / 167°F, if Temp. > 75°C / 167°F
system will automatically power off.
Monitor CPU Temp. at 80°C / 176°F, if Temp. > 80°C / 176°F
system will automatically power off.
Monitor CPU Temp. at 85°C / 185°F, if Temp. > 85°C / 185°F
system will automatically power off.
Monitor CPU Temp. at 90°C / 194°F, if Temp. > 90°C / 194°F
system will automatically power off.
Monitor CPU Temp. at 95°C / 203°F, if Temp. > 95°C / 203°F
system will automatically power off.
Fan Fail Alarm
CPU / Power / System
Disabled
Enabled
Fan Fail Alarm Function Disabled. (Default value)
Fan Fail Alarm Function Enabled.
68
6OMM7 Motherboard
Frequency/Voltage Control
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
Frequency/Voltage Control
Auto Detect DIMM/PCI Clk
Enabled
Item Help
CPU Clock Ratio
X3
Menu Level 4
↑↓→ ←Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 10: Frequency/Voltage Control
•
Auto Detect DIMM/PCI Clk
Disabled
Enabled
•
Disabled Auto Detect DIMM/PCI Clk.
Enabled Auto Detect DIMM/PCI Clk. (Default value)
CPU Clock Ratio
This option will not be shown if you are using a CPU with the locked ratio.
X3/X3.5X/X4/X4.5/X5/X5.5/X6/X6.5/X7/X7.5/X8
69
BIOS Setup
Load Fail-Safe Defaults
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
4Standard CMOS Features
4Frequency/Voltage Control
4Advanced BIOS Features
Load Fail - Safe Defaults
4Advanced Chipset Features
Load Optimized Defaults
4Integrated Peripherals
Set Supervisor Password
4Power Management Setup
Set User Password
Load Fail-Safe Defaults
(Y/N)?
4PnP/PCI Configurations
Save
& Exit N
Setup
4PC Health Status
Exit Without Saving
↑↓→ ← : Select Item
ESC:Quit
F10:Save & Exit Setup
Load Fail-Safe Defaults
Figure 11: Load Fail-Safe Defaults
•
Load Fail-Safe Defaults
Fail−Safe defaults contain the most appropriate values of the system parameters that allow
minimum system performance.
70
6OMM7 Motherboard
Load Optimized Defaults
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
4Standard CMOS Features
4Frequency/Voltage Control
4Advanced BIOS Features
Load Fail-Safe Defaults
4Advanced Chipset Features
Load Optimized Defaults
4Integrated Peripherals
Set Supervisor Password
4Power Management Setup
Set User Password
Load Optimized Defaults
(Y/N)?
N
4PnP/PCI Configurations
Save &
Exit Setup
4PC Health Status
Exit Without Saving
↑↓→ ← : Select Item
ESC:Quit
F10:Save & Exit Setup
Load Optimized Defaults
Figure 12: Load Optimized Defaults
•
Load Optimized Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the
system automatically detects.
71
BIOS Setup
Set Supervisor / User Password
When you select this function, the following message will appear at the center of the screen to
assist you in creating a password.
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
4Standard CMOS Features
4Frequency/Voltage Control
4Advanced BIOS Features
Load Fail-Safe Defaults
4Advanced Chipset Features
Load Optimized Defaults
4Integrated Peripherals
Set Supervisor Password
4Power Management Setup
Set User Password
Enter Password:
4PnP/PCI Configurations
Save & Exit Setup
4PC Health Status
Exit Without Saving
ESC:Quit
F10:Save & Exit Setup
↑↓→ ← : Select Item
Change / Set / Disable Password
Figure 13: Password Setting
Type the password, up to eight characters, and press <Enter>. The password typed now will clear
the previously entered password from CMOS memory. You will be asked to confirm the password.
Type the password again and press <Enter>. You may also press <Esc> to abort the selection
and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
“PASSWORD DISABLED” will appear to confirm the password being disabled. Once the
password is disabled, the system will boot and you can enter Setup freely.
If you select “System” at “Security Option” in BIOS Features Setup Menu, you will be prompted
for the password every time the system is rebooted or any time you try to enter Setup Menu. If
you select “Setup” at “Security Option” in BIOS Features Setup Menu, you will be prompted only
when you try to enter Setup.
72
6OMM7 Motherboard
Save & Exit Setup
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
4Standard CMOS Features
4Frequency/Voltage Control
4Advanced BIOS Features
Load Fail-Safe Defaults
4Advanced Chipset Features
Load Optimized Defaults
4Integrated Peripherals
Set Supervisor Password
4Power Management Setup
Set User Password
SAVE to CMOS andSave
EXIT& (Y/N)?
Y
4PnP/PCI Configurations
Exit Setup
4PC Health Status
Exit Without Saving
↑↓→ ← : Select Item
ESC:Quit
F10:Save & Exit Setup
Save Data to CMOS
Figure 14: Save & Exit Setup
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
73
BIOS Setup
Exit Without Saving
CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software
4Standard CMOS Features
4Frequency/Voltage Control
4Advanced BIOS Features
Load Fail-Safe Defaults
4Advanced Chipset Features
Load Optimized Defaults
4Integrated Peripherals
Set Supervisor Password
4Power Management Setup
Set User Password
Quit Without SavingSave
(Y/N)?
N Setup
4PnP/PCI Configurations
& Exit
4PC Health Status
Exit Without Saving
↑↓→ ← : Select Item
ESC:Quit
F10:Save & Exit Setup
Abandon all Datas
Figure 15: Exit Without Saving
Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.
74
6OMM7 Motherboard
Appendix
Appendix A: Intel 815 Chipsets Driver Installation
A. Windows 9x INF Update Utility
Insert the support CD that came with your motherboard into your CD-ROM drive or double-click
the CD drive icon in My Computer to bring up the setup screen.
1.Click “Windows 9x INF Update
Utility” item.
2.Click ”Next”.
(1)
(2)
4.Click ”Next”.
3.Click ”Yes”.
(4)
(3)
73
Appendix
5.Click “Finish” to
restart computer.
(6)
(5)
74
6OMM7 Motherboard
B: Intel 815 Chipsets VGA Graphics Driver Installation
Insert the support CD that came with your motherboard into your CD-ROM drive or double-click
the CD drive icon in My Computer to bring up the setup screen.
1.Click “Intel 815 Chipset VGA
Graphics Driver” item.
2.Click ”Next”.
(1)
(2)
4.Click ”Next”
.
3.Click ”Yes”.
(4)
(3)
5.Click “Finish” to
restart computer.
(6)
(5)
75
Appendix
C. Intel ICH IDE ATA66 Driver Installation
Insert the support CD that came with your motherboard into your CD-ROM drive or double-click
the CD drive icon in My Computer to bring up the setup screen.
1.Click “Intel ICH IDE ATA66
Driver” item.
2.Click ”Next”.
(1)
(2)
3.Click ”Yes”.
4.Click ”Next”
.
(3)
(4)
5.Click ”Next”
.
(6)
(5)
76
6OMM7 Motherboard
6.Click “Finish” to
restart computer.
(7)
77
Appendix
Appendix B: SigmaTel Sound Driver Installation
Insert the support CD that came with your motherboard into your CD-ROM drive or double-click
the CD drive icon in My Computer to bring up the setup screen.
Press
“Audio”
icon.
2.Click “Next “.
1.Click “SigmaTel
Sound Driver.
(1)
(2)
4.Click “Next
“.
3.Click “Yes “.
(4)
(3)
5.Click “Finish” to
restart Computer “.
(5)
78
6OMM7 Motherboard
Appendix C: BIOS Flash Procedure
BIOS update procedure:
ü
Please check your BIOS vendor (AMI or AWARD) on the motherboard.
ü
It is recommended you copy the AWDFlash.exe or AMIFlash.exe in driver CD
(D:\>Utility\BIOSFlash) and the BIOS binary files into the directory you made in your hard
disk. ¡ i
i.e:C:\>Utility\ (C:\>Utility : denotes the driver and the directory where you put the
flash utilities and BIOS file in.)¡ j
ü
Restart your computer into MS-DOS mode or command prompt only for Win95/98, go into
the directory where the new BIOS file are located use the utility AWDFlash.exe or
AMIFlash.exe to update the BIOS.
ü
Type the following command once you have enter the directory where all the files are
located
C:\utility\ AWDFlash or AMIFlash <filename of the BIOS binary file intended for flashing>.
ü
Once the process is finished, reboot the system.
MNote: Please download the newest BIOS from our website (www.gigabyte.com.tw) or contact
your local dealer for the file.
79
Appendix
Appendix D: Issues To Beware Of When Installing AMR
Please use inverse AMR card like the one in order to avoid mechanical problem. (See Figure A)
PCI Slot
Figure A: Inverse AMR Card (Default)
PCI Slot
Figure B: Non inverse AMR Card
80
6OMM7 Motherboard
Appendix E: Issues To Beware Of When Installing GA-AIMM Card (Optional)
Install:
1.Insert the card at an angle as shown
below. Push the card forward a little
making sure it’s tight.
2.Push the card down as per picture below.
(1)
(2)
Remove:
4.Lift up the card and remove from the slot.
3.Push the extruding piece of the AGP
retention module out. Pull the card from the
tip.
(4)
(3)
81
Appendix
Appendix F: Acronyms
Acro.
ACPI
POST
LAN
ECP
APM
DMA
MHz
ESCD
CPU
SMP
USB
OS
ECC
IDE
SCI
LBA
EMC
BIOS
SMI
IRQ
NIC
A.G.P.
S.E.C.C.
LED
EPP
CMOS
I/O
ESD
OEM
SRAM
VID
DMI
MIDI
IOAPIC
DIMM
DRAM
PAC
AMR
Meaning
Advanced Configuration and Power Interface
Power-On Self Test
Local Area Network
Extended Capabilities Port
Advanced Power Management
Direct Memory Access
Megahertz
Extended System Configuration Data
Central Processing Unit
Symmetric Multi-Processing
Universal Serial Bus
Operating System
Error Checking and Correcting
Integrated Dual Channel Enhanced
Special Circumstance Instructions
Logical Block Addressing
Electromagnetic Compatibility
Basic Input / Output System
System Management Interrupt
Interrupt Request
Network Interface Card
Accelerated Graphics Port
Single Edge Contact Cartridge
Light Emitting Diode
Enhanced Parallel Port
Complementary Metal Oxide Semiconductor
Input / Output
Electrostatic Discharge
Original Equipment Manufacturer
Static Random Access Memory
Voltage ID
Desktop Management Interface
Musical Interface Digital Interface
Input Output Advanced Programmable Input Controller
Dual Inline Memory Module
Dynamic Random Access Memory
PCI A.G.P. Controller
Audio Modem Riser
To be continued…
82
6OMM7 Motherboard
Acro.
PCI
RIMM
DRM
ISA
MTH
CRIMM
Meaning
Peripheral Component Interconnect
Rambus in-line Memory Module
Dual Retention Mechanism
Industry Standard Architecture
Memory Translator Hub
Continuity RIMM
83
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement