Safety of household and similar electrical appliances Part 2

Safety of household and similar electrical appliances Part 2
Test Report issued under the responsibility of:
www.nemko.com
TEST REPORT
IEC 60335-2-80
Safety of household and similar electrical appliances
Part 2 : Particular requirements for fans
Report Number. .............................. :
247910
Date of issue ................................... :
2014-01-10
Total number of pages ....................
101 pages and see page 3 for attachment list
Applicant’s name ........................... :
KENNEDE ELECTRONICS MFG CO., LTD.
Address ........................................... :
No.21, Jintong Road, Tangxia Town, Pengjiang District, Jiangmen
City, Guangdong Province, China.
Test specification:
Standard .......................................... :
IEC 60335-2-80:2002 (Second edition) + A1:2004 +A2:2008 in
conj. With IEC 60335-1:2010 (Fifth Edition)
Test procedure ............................... :
CB Scheme
Non-standard test
method
..:
N/A
Test Report Form No. .................... :
IEC60335_2_80E
Test Report Form(s) Originator .... :
DEKRA Certification B.V.
Master TRF ...................................... :
Dated 2012-09
Copyright © 2012 Worldwide System for Conformity Testing and Certification of Electrotechnical
Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Test item description..................... :
Rechargeable Fan
Trade Mark...................................... :
Manufacturer .................................. :
KENNEDE ELECTRONICS MFG CO., LTD.
No.21, Jintong Road, Tangxia Town, Pengjiang District, Jiangmen
City, Guangdong Province, China.
Model/Type reference .................... :
KN-29XXX, see page 6 for model explanation
Ratings ............................................ :
24W or 30W 220-240V~ 50/60Hz; Cl. II, T
Page 2 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Testing procedure and testing location:
CB Testing Laboratory:
Nemko Hong Kong Ltd.
Testing location/ address....................:
Unit 1-5, 15/F, CCT Telecom Building, No. 11 Wo Shing Street,
Fotan, Shatin, N.T., Hong Kong
Associated Laboratory:
Testing location/ address..
...:
Tested by (name + signature):
William Cheung
Approved by (+ signature)......:
Zoe Chan
Testing procedure: TMP
Tested by (name + signature):
Approved by (+ signature)......:
Testing location/ address..
...:
Testing procedure: WMT
Tested by (name + signature):
Witnessed by (+ signature):
Approved by (+ signature)......:
Testing location/ address..
...:
Testing procedure: SMT
Tested by (name + signature):
Approved by (+ signature)......:
Supervised by (+
signature) .......:
Testing location/ address..
...:
Testing procedure: RMT
Tested by (name + signature):
Approved by (+ signature)......:
Supervised by (+
signature) .......:
Testing location/ address..
TRF No. IEC60335_2_80E
...:
Page 3 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
List of Attachments (including a total number of pages in each attachment):
ATTACHMENT: Photo(s), 30 pages
Summary of testing:
Tests performed (name of test and test clause):
Models KN-2905, KN-2712, KN-2903, KN-2926, KN2918HR, KN-2912, KN-2916, KN-2914H, KN-2918H,
KN-2914HR & KN-2926HR were selected as
representative models for full testing. Others for
construction checking (Cl. 22).
All tests were performed under most unfavourable
conditions.
LED and lamp attachment considered by Nemko
report 247910.
The tested samples are complying with the relevant
product standard(s):
IEC 60335-2-80:2002 (Second edition) + A1:2004
+A2:2008
IEC 60335-1:2010 (Fifth Edition)
Summary of compliance with National Differences
N/A
TRF No. IEC60335_2_80E
Testing location:
Nemko Hong Kong Ltd.
Unit 1-5, 15/F, CCT Telecom Building, No. 11 Wo
Shing Street, Fotan, Shatin, N.T., Hong Kong
Page 4 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Copy of marking plate
The artwork below may be only a draft. The use of certification marks on a product must be
authorized by the respective NCBs that own these marks.
Remark:
1)The markings of other models are the same as KN-2918HR except for the model name and/or power
rating.
2) The trademark was marked on the samples.
TRF No. IEC60335_2_80E
Page 5 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Test item particulars .................................................. :
Classification of installation and use ...................... : Portable appliance
Supply Connection .................................................... : Appliance inlet, detachable cord with plug and
connector is delivered together with the appliance,
and/or DC inlet
...................................................................................... :
Possible test case verdicts:
- test case does not apply to the test object ...........: N/A
- test object does meet the requirement ..................: P (Pass)
- test object does not meet the requirement ...........: F (Fail)
Testing ..........................................................................:
Date of receipt of test item .........................................: 2013-11-08
Date (s) of performance of tests ...............................: 2013-11-12 to 2013-12-26
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a
comma /
point is used as the decimal separator.
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory
has been provided ...................................................... :
Yes
Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) .......................... : KENNEDE ELECTRONICS MFG CO., LTD.
No.21, Jintong Road, Tangxia Town, Pengjiang
District, Jiangmen City, Guangdong Province, China.
TRF No. IEC60335_2_80E
Page 6 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
General product information:
It is a rechargeable fan, The appliances are powered by batteries that are recharged in the appliance.
This appliance is applicable in tropical climate.
Main model : KN-29XXX. The “XXX” can be 12, 14, 16, 24, 26, 14H, 16H, 18H or 26H.
30W or 24W 220-240V~ 50/60Hz; Cl. II, T
Variant 1:
Model : KN-290Y. The “Y” can be 3 or 5.
4W or 5W 220-240V~ 50/60Hz; Cl. II, T
Variant 2:
Model : KN-29ZZHR, The “ZZ” can be 14, 16, 18 or 26
24W or 30W 220-240V~ 50/60Hz; Cl. II, T
Variant 3:
Model : KN-2712.
24W 220-240V~ 50/60Hz; Cl. II, T
Model explanation:
Mode of
appliance
KN-29XXX
KN-2912
KN-2924
KN-2926
Motor(type/rating,class)
Transformer
(type/ rating/
class)
Circuit of
appliance
Power
KRS-550STP-35112-123D /
SH-550STP-35112-123D
DC 6V 1,2 / 1,83A Class130
(B)
EI48
220V-240V
50/60Hz
Class130
(B), output
7,5V
EI57
220V-240V
50/60Hz
Class130
(B), output
12,5V
The same as
model KN-2912
24W
KRS-560STP-27110-127.5D
DC 12V 1,3A Class130 (B)
KN-2926H
KN-2918H
KN-2914H
KN-2916H
KN-2914
KN-2916
KN-29Y
KN-2903
KRS-775STP-31120-144.2FD
DC 12V 1,7A Class130 (B)
KRS-560STP-33120-127.5D /
SH-560STP-33120-127.5D
DC 6V 1,75 / 1,58A Class130
(B)
KN-2903M
DC 4,2V 0,22A Class130 (B)
TRF No. IEC60335_2_80E
Type of
control
and fan
Electronic
table fan
The same as
model KN-2924
30W
The same as
model KN2918H
EI57
220V-240V
50/60Hz
Class130
(B), output
7,5V
The same as
model KN2914H
The same as
model KN-2912
24W
-
KN-2903 Circuit
diagram
4W
Electronic
pedestal
fan
Electronic
table fan
Electronic
mini fan
Page 7 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
KN-2905
KN-2905M
DC 4,2V 0,34A Class130 (B)
-
KN-2905 Circuit
diagram
5W
Mode of
appliance
Motor(type/rating,class)
Transformer
(type/ rating/
class)
Circuit of
appliance
Power
KN29ZZHR
KN2918HR
KRS-775STP-31120-144.2FD
DC 12V 1,7A Class130 (B)
KN2926HR
KRS-560STP-27110-127.5D
DC 12V 1,3A Class130 (B)
EI57
220V-240V
50/60Hz
Class130
(B), output
12,5V
The same as
model KN2918HR
Type of
control
and fan
30W
Electronic
pedestal
fan
KN2914HR
KN2916HR
KRS-560STP-33120-127.5D /
SH-560STP-33120-127.5D
DC 6V 1,75 / 1,58A Class130
(B)
EI57
220V-240V
50/60Hz
Class130
(B), output
7,5V
The same as
model KN2914HR
24W
KN-2712
KRS-55 STP-117D /
SH-55 STP-3
-117D
DC 6V 1,3 / 1,83A Class130
(B)
EI48
220V-240V
50/60Hz
Class130
(B), output
7,5V
The same as
model KN-2712
24W
Electronic
table fan
Marking label, user manual, packing text:
Instructions and marking shall be in a language acceptable for the country where the equipment is to be
used.
Mains plug:
If the equipment shall be used with a special mains plug which is not listed in the component list (e.g.
United Kingdom), samples of the modified product must be subject to a test according to the relevant
clauses of the product standard.
Other product properties:
Depending on the country where the equipment is to be used, national deviations may be considered.
Samples of the modified product may be tested again according to relevant clauses of the product
standard, modified by national deviations.
TRF No. IEC60335_2_80E
Page 8 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
5
GENERAL CONDITIONS FOR THE TESTS
Result - Remark
Tests performed according to clause 5, e.g. nature
of supply, sequence of testing, etc.
5.7
Verdict
P
A Fans to be used in tropical climates, the tests of
clause 10,11 and 13 are carried out at 40 °C +/- 2
°C (IEC 60335-2-8)
P
A Fans marked with ambient operating temperature,
the tests of clause 10, 11 and 13 are carried out at
marked value +/- 2 °C (IEC 60335-2-80/A1)
N/A
6
CLASSIFICATION
6.1
Protection against electric shock:
Class 0, 0I, I, II, III ...................................... ..........:
6.2
Protection against harmful ingress of water
N/A
A At least IPX2 for Duct fans (IEC 60335-2-8)
N/A
Class II
P
Tropical climates
P
Rated voltage or voltage range (V) ............ ..........:
220-240V
P
Symbol for nature of supply, or .................. ..........:
~
P
Rated frequency (Hz) ................................. ..........:
50/60Hz
P
Rated power input (W), or .......................... ..........:
30W, 24W, 5W or 4W
P
6.101
Classification to climatic conditions : temperature
climates, tropical climates (IEC 60335-2-8)
7
MARKING AND INSTRUCTIONS
7.1
Rated current (A) ....................................... ..........:
N/A
Manufacturer's or responsible vendor's name,
trademark or identification mark ................. ..........:
Trademark:
P
Model or type reference ............................. ..........:
KN-29XXX, KN-29Y, KN29ZZHR, KN-2712
P
Symbol IEC 60417-5172, for class II appliances
P
IP number, other than IPX0 ........................ ..........:
N/A
Symbol IEC 60417-5180, for class III appliances,
unless
N/A
the appliance is operated by batteries only
N/A
Symbol IEC 60417-5036, for the enclosure of
electrically-operated water valves in external hosesets for connection of an appliance to the water
mains, if the working voltage exceeds extra-low
voltage
N/A
TRF No. IEC60335_2_80E
Page 9 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
P
A For tropical climates marked with letter T (IEC
60335-2-8)
N/A
A Fans intended for operation in location where the
local temperature exceeds 40 °C shall be marked
with the ambient operating temperature. (IEC 603352-80/A1)
7.2
7.3
7.4
7.5
Warning for stationary appliances for multiple
supply
N/A
Warning placed in vicinity of terminal cover
N/A
Range of rated values marked with the lower and
upper limits separated by a hyphen
220-240V
P
Different rated values marked with the values
separated by an oblique stroke
50/60Hz
P
Appliances adjustable for different rated voltages,
the voltage setting is clearly discernible
N/A
Requirement met if frequent changes are not
required and the rated voltage to which the
appliance is to be adjusted is determined from a
wiring diagram
N/A
Appliances with more than one rated voltage or one
or more rated voltage ranges, marked with rated
input or rated current for each rated voltage or
range, unless
P
the power input is related to the arithmetic mean
value of the rated voltage range
P
Relation between marking for upper and lower
limits of rated power input or rated current and
voltage is clear
7.6
7.7
7.8
Verdict
N/A
Correct symbols used
P
Symbol for nature of supply placed next to rated
voltage
P
Symbol for class II appliances placed unlikely to be
confused with other marking
P
Units of physical quantities and their symbols
according to international standardized system
P
Connection diagram fixed to appliances to be
connected to more than two supply conductors and
appliances for multiple supply, unless
N/A
correct mode of connection is obvious
N/A
Except for type Z attachment, terminals for connection to the supply mains
indicated as follows:
TRF No. IEC60335_2_80E
Page 10 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
- marking of terminals exclusively for the neutral
conductor (letter N)
N/A
- marking of protective earthing terminals (symbol
IEC 60417-5019)
N/A
- marking not placed on removable parts
N/A
7.9
Marking or placing of switches which may cause a
hazard
7.10
Indications of switches on stationary appliances
and controls on all appliances by use of figures,
letters or other visual means ...................... ..........:
P
Letters, symbols and Indicating
light
P
This applies also to switches which are part of a
control
N/A
If figures are used, the off position indicated by the
figure 0
N/A
The figure 0 indicates only OFF position, unless no
confusion with the OFF position
N/A
7.11
Indication for direction of adjustment of controls
N/A
7.12
Instructions for safe use provided
Details concerning precautions during user
maintenance
P
N/A
The instructions state that:
- the appliance is not to be used by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction
P
- children being supervised not to play with the
appliance
P
For a part of class III construction supplied from a
detachable power supply unit, the instructions state
that the appliance is only to be used with the unit
provided
N/A
Instructions for class III appliances state that it must
only be supplied at SELV, unless
N/A
it is a battery-operated appliance, the battery being
charged outside the appliance
N/A
A For the guards have to be removed purpose for cleaning should: (IEC 60335-280/A1)
Ensure that the fan is switched off from the supply
mains before removing the guard.
7.12.1
Sufficient details for installation supplied
TRF No. IEC60335_2_80E
P
N/A
Page 11 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
For an appliance intended to be permanently
connected to the water mains and not connected by
a hose-set, this is stated
Verdict
N/A
A The installation instructions include the substance of the following: (IEC 60335-2-8)
- the model or type reference of a luminaire
N/A
- mounting location for partition fans
N/A
- The installation height for fans intended to be
mounted at high level
N/A
- that precautions for duct and partition fans.
N/A
7.12.2
Stationary appliances not fitted with means for
disconnection from the supply mains having a
contact separation in all poles that provide full
disconnection under overvoltage category III, the
instructions state that means for disconnection
must be incorporated in the fixed wiring in
accordance with the wiring rules
N/A
7.12.3
Insulation of the fixed wiring in contact with parts
exceeding 50 K during clause 11; instructions state
that the fixed wiring must be protected
N/A
7.12.4
Instructions for built-in appliances:
7.12.5
- dimensions of space
N/A
- dimensions and position of supporting and fixing
N/A
- minimum distances between parts and
surrounding structure
N/A
- minimum dimensions of ventilating openings and
arrangement
N/A
- connection to supply mains and interconnection of
separate components
N/A
- allow disconnection of the appliance after
installation, by accessible plug or a switch in the
fixed wiring, unless
N/A
a switch complying with 24.3
N/A
Replacement cord instructions, type X attachment
with a specially prepared cord
N/A
Replacement cord instructions, type Y attachment
7.12.6
Appliance inlet used
N/A
Replacement cord instructions, type Z attachment
N/A
Caution in the instructions for appliances
incorporating a non-self-resetting thermal cut-out
that is reset by disconnection of the supply mains, if
this cut-out is required to comply with the standard
N/A
TRF No. IEC60335_2_80E
Page 12 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
7.12.7
Instructions for fixed appliances stating how the
appliance is to be fixed
7.12.8
Instructions for appliances connected to the water mains:
Verdict
N/A
- max. inlet water pressure (Pa) ................. ..........:
N/A
- min. inlet water pressure, if necessary (Pa) ........:
N/A
Instructions concerning new and old hose-sets for
appliances connected to the water mains by
detachable hose-sets
N/A
7.13
Instructions and other texts in an official language
English checked
P
7.14
Marking clearly legible and durable, rubbing test as
specified
P
7.15
Markings on a main part
P
Marking clearly discernible from the outside, if
necessary after removal of a cover
P
For portable appliances, cover can be removed or
opened without a tool
N/A
For stationary appliances, name, trademark or
identification mark and model or type reference
visible after installation
N/A
For fixed appliances, name, trademark or
identification mark and model or type reference
visible after installation according to the instructions
N/A
Indications for switches and controls placed on or
near the components. Marking not on parts which
can be positioned or repositioned in such a way
that the marking is misleading
P
7.16
Marking of a possible replaceable thermal link or
fuse link clearly visible with regard to replacing the
link
N/A
8
PROTECTION AGAINST ACCESS TO LIVE PARTS
8.1
Adequate protection against accidental contact with
live parts
P
8.1.1
Requirement applies for all positions, detachable
parts removed
P
Lamps behind a detachable cover not removed, if
conditions met
N/A
Insertion or removal of lamps, protection against
contact with live parts of the lamp cap
N/A
Use of test probe B of IEC 61032, with a force not
exceeding 1 N: no contact with live parts
TRF No. IEC60335_2_80E
P
Page 13 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
A Lamps are not removed. However, during insertion
or removal of lamps, no contact with live parts of the
lamp cap. (IEC 60335-2-8)
8.1.2
Verdict
N/A
Use of test probe 13 of IEC 61032, with a force not
exceeding 1 N, through openings in class 0
appliances and class II appliances/constructions:
no contact with live parts
P
Test probe 13 also applied through openings in
earthed metal enclosures having a non-conductive
coating: no contact with live parts
N/A
8.1.3
For appliances other than class II, use of test probe
41 of IEC 61032, with a force not exceeding 1 N: no
contact with live parts of visible glowing heating
elements
N/A
8.1.4
Accessible part not considered live if:
- safety extra-low a.c. voltage: peak value not
exceeding 42.4 V
8.1.5
8.2
For models except KN-2903 &
KN-2905
P
- safety extra-low d.c. voltage: not exceeding
42.4 V
N/A
- or separated from live parts by protective
impedance
N/A
If protective impedance: d.c. current not exceeding
2 mA, and
N/A
a.c. peak value not exceeding 0.7 mA
N/A
- for peak values over 42.4 V up to and including
450 V, capacitance not exceeding 0,1 F
N/A
- for peak values over 450 V up to and including
15 kV, discharge not exceeding 45 C
N/A
- for peak values over 15kV, the energy in the
discharge not exceeding 350 mJ
N/A
Live parts protected at least by basic insulation before installation or assembly:
- built-in appliances
N/A
- fixed appliances
N/A
- appliances delivered in separate units
N/A
Class II appliances and constructions constructed
so that there is adequate protection against
accidental contact with basic insulation and metal
parts separated from live parts by basic insulation
only
P
Only possible to touch parts separated from live
parts by double or reinforced insulation
P
TRF No. IEC60335_2_80E
Page 14 of 101
Report No. 247910
IEC 60335-2-80
Clause
8.2
9
Requirement - Test
Result - Remark
A Remove the detachable parts for user maintenance
purpose, the basic insulation of internal wiring may
be touched provide the equivalent insulating of cords
complying with IEC 60227 or IEC 60245. (IEC
60335-2-80/A1)
N/A
STARTING OF MOTOR-OPERATED APPLIANCES
Requirements and tests are specified in part 2
when necessary
10
POWER INPUT AND CURRENT
10.1
Power input at normal operating temperature, rated (see appended table)
voltage and normal operation not deviating from
rated power input by more than shown in table 1 .:
N/A
P
Test carried out at upper and lower limits of the
ranges for appliances with one or more rated
voltage ranges, unless
N/A
the rated power input is related to the arithmetic
mean value
P
A Appliances are tested with shutters or similar
devices in the open position.(IEC 60335-2-80)
10.2
Verdict
N/A
Current at normal operating temperature, rated
voltage and normal operation not deviating from
rated current by more than shown in table 2 .........:
N/A
Test carried out at upper and lower limits of the
ranges for appliances with one or more rated
voltage ranges, unless
N/A
the rated current is related to the arithmetic mean
value of the range
N/A
A Appliances are tested with shutters or similar
devices in the open position. (IEC 60335-2-80)
N/A
11
HEATING
11.1
No excessive temperatures in normal use
P
11.2
The appliance is held, placed or fixed in position as Placed on floor
described ...............................................................:
P
11.3
Temperature rises, other than of windings,
determined by thermocouples
P
Temperature rises of windings determined by
resistance method, unless
P
the windings are non-uniform or it is difficult to
make the necessary connections
N/A
Heating appliances operated under normal
operation at 1.15 times rated power input (W) .....:
N/A
11.4
TRF No. IEC60335_2_80E
Page 15 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
11.5
Motor-operated appliances operated under normal
operation at most unfavourable voltage between
0.94 and 1.06 times rated voltage (V) ...................:
1,06 x 240V = 254,4V
11.6
Combined appliances operated under normal
operation at most unfavourable voltage between
0.94 and 1.06 times rated voltage (V) ...................:
11.7
11.8
P
(see appended table)
N/A
if there is doubt with regard to classification of
insulation,
N/A
tests of Annex C are carried out
N/A
Sealing compound does not flow out
P
Protective devices do not operate, except
P
N/A
P
A The temperature rise limits for appliances for
tropical climates are reduced by 15 K. (IEC 603352-80)
13.1
A The temperature rise limits for fans marked with an
ambient operating temperature are reduced by the
difference between the marked value and 25 °C.
(IEC 60335-2-80/A1)
LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING
TEMPERATURE
Leakage current not excessive and electric strength
adequate
Motor-operated appliances and combined
appliances supplied at 1.06 times the rated voltage
(V) ..........................................................................:
N/A
P
Heating appliances operated at 1.15 times the
rated power input (W) ............................................:
13.2
P
If the temperature rise of a motor winding exceeds
the value of table 3, or
components in protective electronic circuits tested
for the number of cycles specified in 24.1.4
13
P
N/A
R Appliances are operated until steady conditions are
established. (IEC 60335-2-80)
Temperature rises monitored continuously and not
exceeding the values in table 3 ............................:
Verdict
N/A
1,06 x 240V = 254,4V
P
Protective impedance and radio interference filters
disconnected before carrying out the tests
N/A
For class 0, class II and class III appliances,
leakage current measured by means of the circuit
described in figure 4 of IEC 60990
P
For other appliances, a low impedance ammeter
may be used
N/A
TRF No. IEC60335_2_80E
Page 16 of 101
Report No. 247910
IEC 60335-2-80
Clause
13.3
Requirement - Test
Result - Remark
Leakage current measurements ...........................:
(see appended table)
The appliance is disconnected from the supply
Electric strength tests according to table 4 ...........:
No breakdown during the tests
14
Verdict
P
P
(see appended table)
P
P
TRANSIENT OVERVOLTAGES
Appliances withstand the transient over-voltages to
which they may be subjected
N/A
Clearances having a value less than specified in
table 16 subjected to an impulse voltage test, the
test voltage specified in table 6 .............................:
N/A
No flashover during the test, unless
N/A
of functional insulation if the appliance complies
with clause 19 with the clearance short-circuited
N/A
15
MOISTURE RESISTANCE
15.1
Enclosure provides the degree of moisture
protection according to classification of the
appliance
N/A
Compliance checked as specified in 15.1.1, taking
into account 15.1.2, followed by the electric
strength test of 16.3
N/A
No trace of water on insulation which can result in a
reduction of clearances or creepage distances
below values specified in clause 29
N/A
Appliances, other than IPX0, subjected to tests as
specified in IEC 60529 ..........................................:
N/A
Water valves containing live parts in external hoses
for connection of an appliance to the water mains
tested as specified for IPX7 appliances
N/A
A The outer part of fans to be installed in the external
structure is subjected to subclause 14.2.4(a) of IEC
60529. The outer part of fans is not to be installed in
the external structure is protected against the water.
(IEC 60335-2-80/A1)
N/A
A The fans supplied as rated voltage with shutters or
similar devices being the open position. (IEC 603352-80/A1)
N/A
Hand-held appliance turned continuously through
the most unfavourable positions during the test
N/A
Built-in appliances installed according to the
instructions
N/A
15.1.1
15.1.2
TRF No. IEC60335_2_80E
Page 17 of 101
Report No. 247910
IEC 60335-2-80
Clause
15.2
Requirement - Test
Result - Remark
Verdict
Appliances placed or used on the floor or table
placed on a horizontal unperforated support
N/A
Appliances normally fixed to a wall and appliances
with pins for insertion into socket-outlets are
mounted on a wooden board
N/A
For IPX3 appliances, the base of wall mounted
appliances is placed at the same level as the pivot
axis of the oscillating tube
N/A
For IPX4 appliances, the horizontal centre line of
the appliance is aligned with the pivot axis of the
oscillating tube, and
N/A
for appliances normally used on the floor or table,
the movement is limited to two times 90 for a
period of 5 min, the support being placed at the
level of the pivot axis of the oscillating tube
N/A
Wall-mounted appliances, take into account the
distance to the floor stated in the instructions
N/A
Appliances normally fixed to a ceiling are mounted
underneath a horizontal unperforated support, the
pivot axis of the oscillating tube located at the level
of the underside of the support, and
N/A
for IPX4 appliances, the movement of the tube is
limited to two times 90 from the vertical for a
period of 5 min
N/A
Appliances with type X attachment fitted with a
flexible cord as described
N/A
Detachable parts subjected to the relevant
treatment with the main part
N/A
However, if a part has to be removed for user
maintenance and a tool is needed, this part is not
removed
N/A
Spillage of liquid does not affect the electrical
insulation
N/A
Appliances with type X attachment fitted with a
flexible cord as described
N/A
Appliances incorporating an appliance inlet tested
with or without an connector, whichever is most
unfavourable
N/A
Detachable parts are removed
N/A
Overfilling test with additional amount of
water, over a period of 1 min (l) ............................:
N/A
The appliance withstands the electric strength test
of 16.3
N/A
TRF No. IEC60335_2_80E
Page 18 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
No trace of water on insulation that can result in a
reduction of clearances or creepage distances
below values specified in clause 29
15.3
Appliances proof against humid conditions
Verdict
N/A
R.H. 93%; 30°C
P
Checked by test Cab: Damp heat steady state in
IEC 60068-2-78
P
Detachable parts removed and subjected, if
necessary, to the humidity test with the main part
N/A
Humidity test for 48 h in a humidity cabinet
P
Reassembly of those parts that may have been
removed
N/A
The appliance withstands the tests of clause 16
P
16
LEAKAGE CURRENT AND ELECTRIC STRENGTH
16.1
Leakage current not excessive and electric strength
adequate
P
Protective impedance disconnected from live parts
before carrying out the tests
N/A
Tests carried out at room temperature and not
connected to the supply
16.2
Single-phase appliances: test voltage 1.06 times
rated voltage (V) ....................................................:
P
1,06 x 240V = 254,4V
Three-phase appliances: test voltage 1.06 times
rated voltage divided by 3 (V) .............................:
Leakage current measurements ...........................:
16.3
N/A
(see appended table)
P
Limit values doubled if:
N/A
- all controls have an off position in all poles, or
N/A
- the appliance has no control other than a thermal
cut-out, or
N/A
- all thermostats, temperature limiters and energy
regulators do not have an off position, or
N/A
- the appliance has radio interference filters
N/A
With the radio interference filters disconnected, the
leakage current do not exceed limits specified .....:
N/A
Electric strength tests according to table 7 ...........:
(see appended table)
Test voltage applied between the supply cord and
inlet bushing and cord guard and cord anchorage
as specified ...........................................................:
No breakdown during the tests
17
P
OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS
TRF No. IEC60335_2_80E
P
N/A
P
Page 19 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Verdict
No excessive temperatures in transformer or
(see appended table)
associated circuits in event of short-circuits likely to
occur in normal use ...............................................:
P
Appliance supplied with 1.06 or 0.94 times rated
1,06 × 240 V=254,4 V
voltage under the most unfavourable short-circuit or
overload likely to occur in normal use (V) .............:
P
Basic insulation is not short-circuited
P
Temperature rise of insulation of the conductors of
safety extra-low voltage circuits not exceeding the
relevant value specified in table 3 by more than
15 K
P
Temperature of the winding not exceeding the
value specified in table 8
P
However, limits do not apply to fail-safe
transformers complying with sub-clause 15.5 of IEC
61558-1
18
Result - Remark
N/A
ENDURANCE
Requirements and tests are specified in part 2
when necessary
N/A
19
ABNORMAL OPERATION
19.1
The risk of fire, mechanical damage or electric
shock under abnormal or careless operation
obviated
P
Electronic circuits so designed and applied that a
fault will not render the appliance unsafe .............:
P
Appliances incorporating heating elements
subjected to the tests of 19.2 and 19.3, and
N/A
if the appliance also has a control that limit the
temperature during clause 11 it is subjected to the
test of 19.4, and
N/A
if applicable, to the test of 19.5
N/A
Appliances incorporating PTC heating elements are
also subjected to the test of 19.6
N/A
Appliances incorporating motors subjected to the
tests of 19.7 to 19.10, as applicable
P
Appliances incorporating electronic circuits
subjected to the tests of 19.11 and 19.12, as
applicable
P
Appliances incorporating contactors or relays
subjected to the test of 19.14, being carried out
before the tests of 19.11
TRF No. IEC60335_2_80E
N/A
Page 20 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Appliances incorporating voltage selector switches
subjected to the test of 19.15
N/A
Unless otherwise specified, the tests are continued
until a non-self-resetting thermal cut-out operates,
or
P
until steady conditions are established
P
If a heating element or intentionally weak part
becomes open-circuited, the relevant test is
repeated on a second sample
N/A
A Fans incorporating shutters or similar subjected to
the test of cl. 19.101 (IEC 60335-2-80)
N/A
19.2
Test of appliances with heating elements with
restricted heat dissipation; test voltage (V), power
input of 0.85 times rated power input (W) .............:
N/A
19.3
Test of 19.2 repeated; test voltage (V), power input
of 1.24 times rated power input (W) ......................:
N/A
19.4
Test conditions as in clause 11, any control limiting
the temperature during tests of clause 11
short-circuited
N/A
19.5
Test of 19.4 repeated on Class 0I and I appliances
with tubular sheathed or embedded heating
elements. No short-circuiting, but one end of the
element connected to the sheath
N/A
The test repeated with reversed polarity and the
other end of the heating element connected to the
sheath
N/A
The test is not carried out on appliances intended
to be permanently connected to fixed wiring and on
appliances where an all-pole disconnection occurs
during the test of 19.4
N/A
Appliances with PTC heating elements tested at
rated voltage, establishing steady conditions
N/A
The working voltage of the PTC heating element is
increased by 5% and the appliance is operated until
steady conditions are re-established. The voltage is
then increased in similar steps until 1.5 times
working voltage or until the PTC heating element
ruptures (V) ...........................................................:
N/A
Stalling test by locking the rotor if the locked rotor
torque is smaller than the full load torque, or
N/A
19.6
19.7
locking moving parts of other appliances
Locked rotor, capacitors open-circuited one at a
time
TRF No. IEC60335_2_80E
See annex I for models KN2903 & KN-2905
P
N/A
Page 21 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Test repeated with capacitors short-circuited one at
a time, unless
N/A
capacitor is of class P2 of IEC 60252-1
N/A
Appliances with timer or programmer supplied with
rated voltage for each of the tests, for a period
equal to the maximum period allowed...................:
For remote models, tested
with and without timer (max.
period 0,5 hour) on
P
Other appliances supplied with rated voltage for a
period as specified ................................................:
Until steady conditions
P
Winding temperatures not exceeding values
specified in table 8.................................................:
(see appended table)
P
A Mounting of separate control (IEC 60335-2-80)
N/A
Approximately 50 % of the area of each ventilating
opening is blocked. (IEC 60335-2-80)
N/A
Winding temperatures not exceeding values
specified in table 8 (IEC 60335-2-80)
N/A
The temperature rise of the board not exceed: (IEC 60335-2-80)
– 50 K, for appliances with T marking;
N/A
– 65 K, for other appliances.
N/A
19.8
Multi-phase motors operated at rated voltage with
one phase disconnected
N/A
19.9
Not applicable. (IEC 60335-2-80)
N/A
19.10
Series motor operated at 1.3 times rated voltage for
1 min (V) ................................................................:
N/A
During the test, parts not being ejected from the
appliance
N/A
Electronic circuits, compliance checked by
evaluation of the fault conditions specified in
19.11.2 for all circuits or parts of circuits, unless
P
19.11
they comply with the conditions specified in 19.11.1
N/A
Appliances incorporating an electronic circuit that
relies upon a programmable component to function
correctly, subjected to the test of 19.11.4.8, unless
N/A
restarting does not result in a hazard
N/A
Appliances having a device with an off position
obtained by electronic disconnection, or a device
placing the appliance in a stand-by mode,
subjected to the tests of 19.11.4
P
If the safety of the appliance under any of the fault
conditions depends on the operation of a miniature
fuse-link complying with IEC 60127, the test of
19.12 is carried out
P
TRF No. IEC60335_2_80E
Page 22 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
During and after each test the following is checked:
- the temperature of the windings do not exceed the
values specified in table 8
P
- the appliance complies with the conditions
specified in 19.13
P
- any current flowing through protective impedance
not exceeding the limits specified in 8.1.4
N/A
If a conductor of a printed board becomes open-circuited, the appliance is
considered to have withstood the particular test, provided both of the following
conditions are met:
19.11.1
19.11.2
- the base material of the printed circuit board
withstands the test of Annex E
N/A
- any loosened conductor does not reduce
clearance or creepage distances between live parts
and accessible metal parts below the values
specified in clause 29
N/A
Fault conditions a) to g) in 19.11.2 are not applied to circuits or parts of circuits
meeting both of the following conditions:
- the electronic circuit is a low-power circuit, that is,
the maximum power at low-power points does not
exceed 15 W according to the tests specified
N/A
- the protection against electric shock, fire hazard,
mechanical hazard or dangerous malfunction of
other parts of the appliance does not rely on the
correct functioning of the electronic circuit
N/A
Fault conditions applied one at a time, the appliance operating under conditions
specified in clause 11, but supplied at rated voltage, duration of the tests as
specified:
a) short circuit of functional insulation if clearances
or creepage distances are less than the values
specified in clause 29
N/A
b) open circuit at the terminals of any component
P
c) short circuit of capacitors, unless
P
they comply with IEC 60384-14
N/A
d) short circuit of any two terminals of an electronic
component, other than integrated circuits
P
This fault condition is not applied between the two
circuits of an optocoupler
N/A
e) failure of triacs in the diode mode
P
f) failure of microprocessors and integrated circuits
P
g) failure of an electronic power switching device
P
TRF No. IEC60335_2_80E
Page 23 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Each low power circuit is short-circuited by
connecting the low-power point to the pole of the
supply source from which the measurements were
made
N/A
19.11.3
If the appliance incorporates a protective electronic
circuit which operates to ensure compliance with
clause 19, the relevant test is repeated with a
single fault simulated, as indicated in a) to g) of
19.11.2
N/A
19.11.4
Appliances having a device with an off position
obtained by electronic disconnection, or
P
a device that can be placed in the stand-by mode,
P
subjected to the tests of 19.11.4.1 to 19.11.4.7, the
device being set in the off position or in the standby mode
No possible unsafe operation
P
Appliances incorporating a protective electronic
circuit subjected to the tests of 19.11.4.1 to
19.11.4.7, the tests being carried out after the
protective electronic circuit has operated, except
that
N/A
appliances operated for 30 s or 5 min during the
test of 19.7 are not subjected to the tests for
electromagnetic phenomena.
N/A
Surge protective devices disconnected, unless
N/A
They incorporate spark gaps
N/A
19.11.4.1
The appliance is subjected to electrostatic
discharges in accordance with IEC 61000-4-2, test
level 4
P
19.11.4.2
The appliance is subjected to radiated fields in
accordance with IEC 61000-4-3, test level 3
P
19.11.4.3
The appliance is subjected to fast transient bursts
in accordance with IEC 61000-4-4, test level 3 or 4
as specified
P
19.11.4.4
The power supply terminals of the appliance
subjected to voltage surges in accordance with IEC
61000-4-5, test level 3 or 4 as specified
P
Earthed heating elements in class I appliances
disconnected
N/A
19.11.4.5
The appliance is subjected to injected currents in
accordance with IEC 61000-4-6, test level 3
P
19.11.4.6
Appliances having a rated current not exceeding 16
A are subjected to the Class 3 voltage dips and
interruptions in accordance with IEC 61000-4-11
P
TRF No. IEC60335_2_80E
Page 24 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Appliances having a rated current exceeding 16 A
are subjected to the Class 3 voltage dips and
interruptions in accordance with IEC 61000-4-34
N/A
19.11.4.7
The appliance is subjected to mains signals in
accordance with IEC 61000-4-13, test level class 2
P
19.11.4.8
The appliance is supplied at rated voltage and
operated under normal operation. After 60s the
power supply is reduced to a level such that the
appliance ceases to respond or parts controlled by
the programmable component cease to operate
N/A
The appliance continues to operate normally, or
N/A
requires a manual operation to restart
N/A
19.12
If the safety of the appliance for any of the fault
conditions specified in 19.11.2 depends on the
operation of a miniature fuse-link complying with
IEC 60127, the test is repeated, measuring the
current flowing through the fuse-link; measured
current (A); rated current of the fuse-link (A).........:
19.13
During the tests the appliance does not emit
flames, molten metal, poisonous or ignitable gas in
hazardous amounts
P
Temperature rises not exceeding the values shown (see appended table)
in table 9 ................................................................:
P
Compliance with clause 8 not impaired
P
If the appliance can still be operated it complies
with 20.2
P
Measured current(A): >6A;
Rated current of the fuselink(A): 1A
P
Insulation, other than of class III appliances or class III constructions that do not
contain live parts, withstands the electric strength test of 16.3, the test voltage as
specified in table 4:
- basic insulation (V) ..............................................:
N/A
- supplementary insulation (V) ..............................:
N/A
- reinforced insulation (V) ......................................:
3000V
P
After operation or interruption of a control,
clearances and creepage distances across the
functional insulation withstand the electric strength
test of 16.3, the test voltage being twice the
working voltage
P
The appliance does not undergo a dangerous
malfunction, and
P
no failure of protective electronic circuits, if the
appliance is still operable
N/A
Appliances tested with an electronic switch in the off position, or in the stand-by
mode:
TRF No. IEC60335_2_80E
Page 25 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
- do not become operational, or
N/A
- if they become operational, do not result in a
dangerous malfunction during or after the tests of
19.11.4
N/A
If the appliance contains lids or doors that are controlled by one or more interlocks,
one of the interlocks may be released provided that:
- the lid or door does not move automatically to an
open position when the interlock is released, and
N/A
- the appliance does not start after the cycle in
which the interlock was released
N/A
Appliances operated under the conditions of clause
11, any contactor or relay contact operating under
the conditions of clause 11 being short-circuited
N/A
For a relay or contactor with more than one contact,
all contacts are short-circuited at the same time
N/A
A relay or contactor operating only to ensure the
appliance is energized for normal use is not shortcircuited
N/A
If more than one relay or contactor operates in
clause 11, they are short-circuited in turn
N/A
19.15
For appliances with a mains voltage selector
switch, the switch is set to the lowest rated voltage
position and the highest value of rated voltage is
applied
N/A
19.101
N/A
20
Fans incorporating shutters or similar that are
operated automatically are supplied at rated voltage
in the closed or open position, whichever is more
unfavourable (IEC 60335-2-80)
STABILITY AND MECHANICAL HAZARDS
20.1
Appliances having adequate stability
P
Tilting test through an angle of 10 , appliance
placed on an inclined plane/horizontal support, not
connected to the supply mains; appliance does not
overturn
P
19.14
A
20.2
Tilting test repeated on appliances with heating
elements, angle of inclination increased to 15
N/A
Possible heating test in overturned position;
temperature rise does not exceed values shown in
table 9
N/A
Portable pedestal fans exceeding 1,7 m and
Max height less than 1,7m
exceeding 10 kg tested with a force of 40 N at 1,5 m. and mass < 10kg
(IEC 60335-2-80)
Moving parts adequately arranged or enclosed as
to provide protection against personal injury
N/A
TRF No. IEC60335_2_80E
P
Page 26 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Protective enclosures, guards and similar parts are
non-detachable, and
P
have adequate mechanical strength
P
Enclosures that can be opened by overriding an
interlock are considered to be detachable parts
N/A
Self-resetting thermal cut-outs and overcurrent
protective devices not causing a hazard by
unexpected closure
N/A
Not possible to touch dangerous moving parts with
the test probe described
20.101
21
21.1
21.2
Verdict
Fan blades, other than those for mounting at high
level, shall be guarded, unless: (IEC 60335-2-80)
-they have a hardness less than D 60 Shore, or
P
Guarded
P
N/A
-they have a peripheral speed less than 15 m/s
when the fan is supplied at rated voltage, or
-the fan has a power output not exceeding 2 W
when supplied at rated voltage.
MECHANICAL STRENGTH
N/A
N/A
Appliance has adequate mechanical strength and is
constructed as to withstand rough handling
P
Checked by applying 3 blows to every point of the
enclosure like to be weak, in accordance with test
Ehb of IEC 60068-2-75, spring hammer test, with
an impact energy of 0,5 J
P
The appliance shows no damage impairing
compliance with this standard, and
P
compliance with 8.1, 15.1 and clause 29 not
impaired
P
If doubt, supplementary or reinforced insulation
subjected to the electric strength test of 16.3
N/A
If necessary, repetition of groups of three blows on
a new sample
N/A
Accessible parts of solid insulation having strength
to prevent penetration by sharp implements
P
Test not applicable if the thickness of
supplementary insulation is at least 1 mm and
reinforced insulation at least 2 mm
The insulation is tested as specified, and does
withstand the electric strength test of 16.3
TRF No. IEC60335_2_80E
Enclosure thickness: 2,1mm
P
N/A
Page 27 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
21.101
Fan guards are subjected to a push and pull force of
20 N. Dangerous moving parts are not accessible
(IEC 60335-2-80)
P
The test probe is applied with a force not exceeding
5N. (IEC 60335-2-80/A2)
P
21.102
Ceiling fans have adequate strength. Load four times
mass (.......) (IEC 60335-2-80)
22
CONSTRUCTION
22.1
Appliance marked with the first numeral of the IP
system, relevant requirements of IEC 60529 are
fulfilled
N/A
A NOTE 101 The enclosure defined in IEC 60529
does not include guards for fan blades. (IEC 603352-80)
N/A
22.2
22.3
22.4
N/A
Stationary appliance: means to ensure all-pole disconnection from the supply being
provided:
- a supply cord fitted with a plug, or
N/A
- a switch complying with 24.3, or
N/A
- a statement in the instruction sheet that a
disconnection incorporated in the fixed wiring is to
be provided, or
N/A
- an appliance inlet
N/A
Singe-pole switches and single-pole protective
devices for the disconnection of heating elements
in single-phase, permanently connected class 01
and class I appliances, connected to the phase
conductor
N/A
Appliance provided with pins: no undue strain on
socket-outlets
N/A
Applied torque not exceeding 0.25 Nm
N/A
Pull force of 50N to each pin after the appliance
has being placed in the heating cabinet; when
cooled to room temperature the pins are not
displaced by more than 1mm
N/A
Each pin subjected to a torque of 0.4Nm; the pins
are not rotating, unless
N/A
rotating does not impair compliance with this
standard
N/A
Appliance for heating liquids and appliance causing
undue vibration not provided with pins for insertion
into socket-outlets
N/A
TRF No. IEC60335_2_80E
Page 28 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
22.5
No risk of electric shock when touching the pins of
the plug, for appliances having a capacitor with
rated capacitance exceeding 0,1 F, the appliance
being disconnected from the supply at the instant of
voltage peak
Voltage not exceeding 34 V (V) ............................:
22.6
Result - Remark
Verdict
P
16V
P
Electrical insulation not affected by condensing
water or leaking liquid
N/A
Electrical insulation of Class II appliances not
affected if a hose ruptures or seal leaks
N/A
In case of doubt, test as described
N/A
22.7
Adequate safeguards against the risk of excessive
pressure in appliances containing liquid or gases or
having steam-producing devices
N/A
22.8
Electrical connections not subject to pulling during
cleaning of compartments to which access can be
gained without the aid of a tool, and that are likely
to be cleaned in normal use
P
22.9
Insulation, internal wiring, windings, commutators
and slip rings not exposed to oil, grease or similar
substances, unless
P
the substance has adequate insulating properties
N/A
Not possible to reset voltage-maintained non-selfresetting thermal cut-outs by the operation of an
automatic switching device incorporated within the
appliance, if:
N/A
- a non-self-resetting thermal cut-out is required by
the standard, and
N/A
- a voltage maintained non-self-resetting thermal
cut-out is used to meet it
N/A
Non-self-resetting thermal motor protectors have a
trip-free action, unless
N/A
they are voltage maintained
N/A
Reset buttons of non-self-resetting controls so
located or protected that accidental resetting is
unlikely
N/A
22.10
22.11
Reliable fixing of non-detachable parts that provide
the necessary degree of protection against electric
shock, moisture or contact with moving parts
P
Obvious locked position of snap-in devices used for
fixing such parts
P
TRF No. IEC60335_2_80E
Page 29 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
No deterioration of the fixing properties of snap-in
devices used in parts that are likely to be removed
during installation or servicing
M
22.12
Verdict
P
The 50 N force is not applied to clips used to fasten No clips used
fan guards. (IEC 60335-2-80)
N/A
Instead, a force of 15 N is applied in any direction
to the clips in an attempt to release them. (IEC
60335-2-80)
Tests as described
N/A
Enclosure: push and pull 50N;
Control panel: push and pull
50N
P
Handles, knobs etc. fixed in a reliable manner
P
Fixing in wrong position of handles, knobs etc.
indicating position of switches or similar
components not possible
P
Axial force 15 N applied to parts, the shape being
so that an axial pull is unlikely to be applied
Axial force 30 N applied to parts, the shape being
so that an axial pull is likely to be applied
N/A
Control panel: push and pull
30N
P
22.13
Unlikely that handles, when gripped as in normal
use, make the operator’s hand touch parts having a
temperature rise exceeding the value specified for
handles which are held for short periods only
N/A
22.14
No ragged or sharp edges creating a hazard for the
user in normal use, or during user maintenance
P
No exposed pointed ends of self-tapping screws or
other fasteners, likely to be touched by the user in
normal use or during user maintenance
P
22.15
Storage hooks and the like for flexible cords
smooth and well rounded
N/A
22.16
Automatic cord reels cause no undue abrasion or
damage to the sheath of the flexible cord, no
breakage of conductors strands and no undue wear
of contacts
N/A
Cord reel tested with 6000 operations, as specified
N/A
Electric strength test of 16.3, voltage of 1000 V
applied
N/A
22.17
Spacers not removable from the outside by hand or
by means of a screwdriver or a spanner
N/A
22.18
Current-carrying parts and other metal parts
resistant to corrosion
22.19
Driving belts not relied upon to provide the required
level of insulation, unless
TRF No. IEC60335_2_80E
P
N/A
Page 30 of 101
Report No. 247910
IEC 60335-2-80
Clause
22.20
22.21
Requirement - Test
Result - Remark
Verdict
constructed to prevent inappropriate replacement
N/A
Direct contact between live parts and thermal
insulation effectively prevented, unless
N/A
material used is non-corrosive, non-hygroscopic
and non-combustible
N/A
Wood, cotton, silk, ordinary paper and fibrous or
hygroscopic material not used as insulation, unless
P
impregnated
N/A
This requirement does not apply to magnesium
oxide and mineral ceramic fibres used for the
electrical insulation of heating elements
N/A
22.22
Appliances not containing asbestos
22.23
Oils containing polychlorinated biphenyl (PCB) not
used
N/A
22.24
Bare heating elements, except in class III
appliances or class III constructions that do not
contain live parts, adequately supported
N/A
In case of rupture, the heating conductor is unlikely
to come in contact with accessible metal parts
N/A
22.25
Sagging heating conductors, except in class III
appliances or class III constructions that do not
contain live parts, cannot come into contact with
accessible metal parts
N/A
22.26
For class III constructions the insulation between
parts operating at safety extra-low voltage and
other live parts complies with the requirements for
double or reinforced insulation
22.27
Parts connected by protective impedance
separated by double or reinforced insulation
N/A
22.28
Metal parts of Class II appliances conductively
connected to gas pipes or in contact with water,
separated from live parts by double or reinforced
insulation
N/A
22.29
Class II appliances permanently connected to fixed
wiring so constructed that the required degree of
access to live parts is maintained after installation
N/A
22.30
Parts serving as supplementary or reinforced
insulation fixed so that they cannot be removed
without being seriously damaged, or
P
so constructed that they cannot be replaced in an
incorrect position, and so that if they are omitted,
the appliance is rendered inoperable or manifestly
incomplete
P
TRF No. IEC60335_2_80E
P
P
Page 31 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
22.31
Neither clearances nor creepage distances over
supplementary and reinforced insulation reduced
below values specified in clause 29 as a result of
wear
P
Neither clearances nor creepage distances
between live parts and accessible parts reduced
below values for supplementary insulation if wires,
screws etc. become loose
P
Supplementary and reinforced insulation
constructed or protected against pollution so that
clearances or creepage distances are not reduced
below the values in clause 29
P
22.32
22.33
22.34
Result - Remark
Verdict
Supplementary insulation of natural or synthetic
rubber resistant to ageing, or arranged and
dimensioned so that creepage distances are not
reduced below values specified in 29.2
N/A
Ceramic material not tightly sintered, similar
materials or beads alone not used as
supplementary or reinforced insulation
N/A
Insulating material in which heating conductors are
embedded is considered to be basic insulation, not
reinforced insulation
N/A
Oxygen bomb test at 70 C for 96 h and 16 h at
room temperature
N/A
Conductive liquids that are or may become
accessible in normal use and conductive liquids
that are in contact with unearthed accessible metal
parts are not in direct contact with live parts
N/A
Electrodes not used for heating liquids
N/A
For class II constructions, conductive liquids that
are or may become accessible in normal use and
conductive liquids that are in contact with
unearthed accessible metal parts, not in direct
contact with basic or reinforced insulation, unless
N/A
the reinforced insulation consists of at least 3 layers
N/A
For class II constructions, conductive liquids which
are in contact with live parts, not in direct contact
with reinforced insulation, unless
N/A
the reinforced insulation consists of at least 3 layers
N/A
An air layer not used as basic or supplementary
insulation in a double insulation system if likely to
be bridged by leaking liquid
N/A
Shafts of operating knobs, handles, levers etc. not
live, unless
P
TRF No. IEC60335_2_80E
Page 32 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
the shaft is not accessible when the part is
removed
22.35
22.36
22.37
Verdict
N/A
For other than class III constructions, handles,
levers and knobs, held or actuated in normal use,
not becoming live in the event of a failure of basic
insulation
P
Such parts being of metal, and their shafts or
fixings are likely to become live in the event of a
failure of basic insulation, are either adequately
covered by insulation material or their accessible
parts are separated from their shafts or fixings by
supplementary insulation
N/A
This requirement does not apply to handles, levers
and knobs on stationary appliances, other than
those of electrical components, provided they are
reliably connected to an earthing terminal or
earthing contact, or separated from live parts by
earthed metal
N/A
Insulating material covering metal handles, levers
and knobs withstand the electric strength test of
16.3 for supplementary insulation
N/A
For appliances other than class III, handles
continuously held in the hand in normal use so
constructed that when gripped as in normal use,
the operators hand is not likely to touch metal parts,
unless
N/A
they are separated from live parts by double or
reinforced insulation
N/A
Capacitors in Class II appliances not connected to
accessible metal parts and their casings, if of
metal, separated from accessible metal parts by
supplementary insulation, unless
N/A
the capacitors comply with 22.42
N/A
22.38
Capacitors not connected between the contacts of
a thermal cut-out
22.39
Lamp holders used only for the connection of lamps
22.40
Motor-operated appliances and combined
appliances intended to be moved while in
operation, or having accessible moving parts, fitted
with a switch to control the motor. The actuating
member of the switch being easily visible and
accessible
TRF No. IEC60335_2_80E
P
N/A
Not intended to be moved
while in operation, nor having
accessible moving parts
N/A
Page 33 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
If the appliance cannot operate continuously,
Without hazard
automatically or remotely without giving rise to a
hazard, appliances for remote operation being fitted
with a switch for stopping the operation. The
actuating member of the switch being easily visible
and accessible
P
22.41
No components, other than lamps, containing
mercury
P
22.42
Protective impedance consisting of at least two
separate components
N/A
Values specified in 8.1.4 not exceeded if any one of
the components are short-circuited or opencircuited
N/A
Resistors checked by the test of 14.1 a) in IEC
60065
N/A
Capacitors checked by the tests for class Y
capacitors in IEC 60384-14
N/A
22.43
Appliances adjustable for different voltages,
accidental changing of the setting of the voltage
unlikely to occur
N/A
22.44
Appliances not having an enclosure that is shaped
or decorated like a toy
P
22.45
When air is used as reinforced insulation,
clearances not reduced below the values specified
in 29.1.3 due to deformation as a result of an
external force applied to the enclosure
P
22.46
For programmable protective electronic circuits
used to ensure compliance with the standard, the
software contains measures to control the
fault/error conditions in table R.1
N/A
Software that contains measures to control the
fault/error conditions specified in table R.2 is to be
specified in parts 2 for particular constructions or to
address specific hazards
N/A
These requirements are not applicable to software
used for functional purpose or compliance with
clause 11
N/A
Appliances connected to the water mains withstand
the water pressure expected in normal use
N/A
No leakage from any part, including any inlet water
hose
N/A
Appliances connected to the water mains
constructed to prevent backsiphonage of nonpotable water
N/A
22.47
22.48
TRF No. IEC60335_2_80E
Page 34 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
22.49
For remote operation, the duration of operation is to
be set before the appliance can be started, unless
P
the appliance switches off automatically or can
operate continuously without hazard
P
22.50
Controls incorporated in the appliance take priority
over controls actuated by remote operation
P
22.51
There is a control on the appliance manually
adjusted to the setting for remote operation before
the appliance can be operated in this mode
N/A
There is a visual indication showing that the
appliance is adjusted for remote operation
N/A
These requirements not necessary on appliances that can operate as follows,
without giving rise to a hazard:
- continuously, or
P
- automatically, or
N/A
- remotely
P
22.52
Socket-outlets on appliances accessible to the user
in accordance with the socket-outlet system used in
the country in which the appliance is sold
N/A
22.101
Appliances having provision for attaching a luminaire
incorporate appropriate terminals and internal wiring.
(IEC 60335-2-80)
N/A
23
INTERNAL WIRING
23.1
Wireways smooth and free from sharp edges
P
Wires protected against contact with burrs, cooling
fins etc.
P
Wire holes in metal well-rounded or provided with
bushings
N/A
23.2
23.3
Wiring effectively prevented from coming into
contact with moving parts
P
Beads etc. on live wires cannot change their
position, and are not resting on sharp edges
N/A
Beads inside flexible metal conduits contained
within an insulating sleeve
N/A
Electrical connections and internal conductors
movable relatively to each other not exposed to
undue stress
P
Flexible metallic tubes not causing damage to
insulation of conductors
Open-coil springs not used
TRF No. IEC60335_2_80E
N/A
P
Page 35 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Adequate insulating lining provided inside a coiled
spring, the turns of which touch one another
Verdict
N/A
M No damage after 100 000 flexings for conductors
flexed during normal use and at rated voltage, or
(IEC 60335-2-80)
P
100 flexings for conductors flexed during user
maintenance
N/A
Electric strength test of 16.3, 1000 V between live
parts and accessible metal parts
P
Not more than 10% of the strands of any conductor
broken, and
P
not more than 30% for wiring supplying circuits that
consume no more than 15W
P
23.4
Bare internal wiring sufficiently rigid and fixed
23.5
The insulation of internal wiring subjected to the
supply mains voltage withstanding the electrical
stress likely to occur in normal use
23.6
Result - Remark
N/A
P
Basic insulation electrically equivalent to the basic
insulation of cords complying with IEC 60227 or
IEC 60245, or
N/A
no breakdown when a voltage of 2000 V is applied
for 15 min between the conductor and metal foil
wrapped around the insulation
P
Sleeving used as supplementary insulation on
internal wiring retained in position by clamping at
both ends, or
N/A
be such that it can only be removed by breaking or
cutting
P
23.7
The colour combination green/yellow only used for
earthing conductors
N/A
23.8
Aluminium wires not used for internal wiring
P
23.9
Stranded conductors not consolidated by soldering
where they are subjected to contact pressure,
unless
P
the contact pressure is provided by spring terminals
N/A
23.10
The insulation and sheath of internal wiring,
incorporated in external hoses for the connection of
an appliance to the water mains, at least equivalent
to that of light polyvinyl chloride sheathed flexible
cord (60227 IEC 52)
N/A
24
COMPONENTS
TRF No. IEC60335_2_80E
Page 36 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
24.1
Components comply with safety requirements in
relevant IEC standards
List of components ................................................:
Result - Remark
P
(see appended table)
24.1.2
24.1.3
P
If components have not been tested and found to
comply with relevant IEC standard for the number
of cycles specified, they are tested in accordance
with 24.1.1 to 24.1.9
P
For components mentioned in 24.1.1 to 24.1.9 no
additional tests specified in the relevant component
standard are necessary other than those specified
in 24.1.1 to 24.1.9
P
Components not tested and found to comply with
relevant IEC standard and components not marked
or not used in accordance with its marking, tested
under the conditions occurring in the appliance
P
Lampholders and starterholders that have not being
tested and found to comply with the relevant IEC
standard, tested as a part of the appliance and
additionally according to the gauging and
interchangeability requirements of the relevant IEC
standard
N/A
No additional tests specified for nationally
standardized plugs such as those detailed in
IEC/TR 60083 or connectors complying with the
standard sheets of IEC 60320-1 and IEC 60309
24.1.1
Verdict
P
Capacitors likely to be permanently subjected to the
supply voltage and used for radio interference
suppression or for voltage dividing, complying with
IEC 60384-14
N/A
If the capacitors have to be tested, they are tested
according to Annex F
N/A
Safety isolating transformers complying with IEC
61558-2-6
N/A
If they have to be tested, they are tested according
to Annex G
P
Switches complying with IEC 61058-1, the number
of cycles of operation being at least 10 000
N/A
If they have to be tested, they are tested according
to Annex H
If the switch operates a relay or contactor, the
complete switching system is subjected to the test
TRF No. IEC60335_2_80E
SS22F25G7, S22F25G9
P
N/A
Page 37 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
If the switch only operates a motor staring relay
complying with IEC 60730-2-10 with the number of
cycles of a least 10 000 as specified, the complete
switching system need not be tested
24.1.4
Verdict
N/A
Automatic controls complying with IEC 60730-1 with the relevant part 2. The
number of cycles of operation being at least:
- thermostats:
10 000
N/A
1 000
N/A
300
N/A
1 000
N/A
30
N/A
3 000
N/A
10 000
N/A
- temperature limiters:
- self-resetting thermal cut-outs:
- voltage maintained non-self-resetting
thermal cut-outs:
- other non-self-resetting thermal cut-outs:
- timers:
- energy regulators:
The number of cycles for controls operating during
clause 11 need not be declared, if the appliance
meets the requirements of this standard when they
are short-circuited
N/A
Thermal motor protectors are tested in combination
with their motor under the conditions specified in
Annex D
N/A
For water valves containing live parts and that are
incorporated in external hoses for connection of an
appliance to the water mains, the degree of
protection declared for subclause 6.5.2 of IEC
60730-2-8 is IPX7
N/A
Appliance couplers complying with IEC 60320-1
N/A
However, for appliances classified higher than
IPX0, the appliance couplers complying with IEC
60320-2-3
N/A
Interconnection couplers complying with IEC
60320-2-2
N/A
24.1.6
Small lamp holders similar to E10 lampholders
complying with IEC 60238, the requirements for
E10 lampholders being applicable
N/A
24.1.7
For remote operation of the appliance via a
telecommunication network, the relevant standard
for the telecommunication interface circuitry in the
appliance is IEC 62151
N/A
24.1.8
The relevant standard for thermal links is IEC
60691
24.1.5
TRF No. IEC60335_2_80E
P
Page 38 of 101
Report No. 247910
IEC 60335-2-80
Clause
24.1.9
24.2
24.3
Requirement - Test
Result - Remark
Verdict
Thermal links not complying with IEC 60691 are
considered to be an intentionally weak part for the
purposes of Clause 19
N/A
Contactors and relays, other than motor starting
relays, tested as part of the appliance
N/A
They are also tested in accordance with Clause 17
of IEC 60730-1, the number of cycles of operations
in 24.1.4 selected according to the contactor or
relay function in the appliance ...............................:
N/A
Appliances not fitted with:
- switches or automatic controls in flexible cords
P
- devices causing the protective device in the fixed
wiring to operate in the event of a fault in the
appliance
P
- thermal cut-outs that can be reset by soldering,
unless
P
the solder has a melding point of at least 230 ˚C
N/A
A Switches or automatic controls in flexible cords are
allowed for appliances not exceeding 25 W. (IEC
60335-2-80)
Switches intended for all-pole disconnection of
stationary appliances are directly connected to the
supply terminals and have a contact separation in
all poles, providing full disconnection under
overvoltage category III conditions
No switches or automatic
controls in flexible cords
N/A
N/A
24.4
Plugs and socket-outlets for extra-low voltage
circuits and heating elements, not interchangeable
with plugs and socket-outlets listed in
IEC/TR 60083 or IEC 60906-1 or with connectors
and appliance inlets complying with the standard
sheets of IEC 60320-1
N/A
24.5
Capacitors in auxiliary windings of motors marked
with their rated voltage and capacitance, and used
accordingly
N/A
Voltage across capacitors in series with a motor
winding does not exceed 1,1 times rated voltage,
when the appliance is supplied at 1,1 times rated
voltage under minimum load
N/A
24.6
Working voltage of motors connected to the supply
mains and having basic insulation that is
inadequate for the rated voltage of the appliance,
not exceeding 42 V
In addition, the motors comply with the
requirements of Annex I
TRF No. IEC60335_2_80E
For models KN-2903 & KN2905
P
P
Page 39 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
24.7
Detachable hose-sets for connection of appliances
to the water mains comply with IEC 61770
N/A
They are supplied with the appliance
N/A
Appliances intended to be permanently connected
to the water mains not connected by a detachable
hose-set
N/A
Motor running capacitors in appliances for which
30.2.3 is applicable and that are permanently
connected in series with a motor winding, not
causing a hazard in event of a failure
N/A
24.8
Result - Remark
Verdict
One or more of the following conditions are to be met:
- the capacitors are of class P2 according to IEC
60252-1
N/A
- the capacitors are housed within a metallic or
ceramic enclosure
N/A
- the distance of separation of the outer surface to
adjacent non-metallic parts exceeds 50 mm
N/A
- adjacent non-metallic parts within 50 mm
withstand the needle-flame test of Annex E
N/A
- adjacent non-metallic parts within 50 mm
classified as at least V-1 according to IEC 6069511-10
N/A
24.101
Thermal cut-outs in duct fans in order to comply with
cl. 19 are not self-resetting (IEC 60335-2-80)
N/A
25
SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS
25.1
Appliance not intended for permanent connection to fixed wiring, means for
connection to the supply:
- supply cord fitted with a plug,
- an appliance inlet having at least the same degree Detachable cord with plug and
of protection against moisture as required for the
connector is delivered together
appliance, or
with the appliance
- pins for insertion into socket-outlets
25.2
25.3
N/A
P
N/A
Appliance not provided with more than one means
of connection to the supply mains
P
Stationary appliance for multiple supply may be
provided with more than one means of connection,
provided electric strength test of 1250 V for 1 min
between each means of connection causes no
breakdown
N/A
Appliance intended to be permanently connected to fixed wiring provided with one
of the following means for connection to the supply mains:
TRF No. IEC60335_2_80E
Page 40 of 101
Report No. 247910
IEC 60335-2-80
Clause
25.4
25.5
Requirement - Test
Result - Remark
Verdict
- a set of terminals allowing the connection of a
flexible cord
N/A
- a fitted supply cord
N/A
- a set of supply leads accommodated in a suitable
compartment
N/A
- a set of terminals for the connection of cables of
fixed wiring, cross-sectional areas specified in 26.6,
and the appliance allows the connection of the
supply conductors after the appliance has been
fixed to its support
N/A
- a set of terminals and cable entries, conduit
entries, knock-outs or glands, allowing connection
of appropriate types of cable or conduit, and the
appliance allows the connection of the supply
conductors after the appliance has been fixed to its
support
N/A
For a fixed appliance constructed so that parts can
be removed to facilitate easy installation, this
requirement is met if it is possible to connect the
fixed wiring without difficulty after a part of the
appliance has been fixed to its support
N/A
Cable and conduit entries, rated current of
appliance not exceeding 16 A, dimension according
to table 10 (mm) ....................................................:
N/A
Introduction of conduit or cable does not reduce
clearances or creepage distances below values
specified in clause 29
N/A
Method for assembling the supply cord to the appliance:
- type X attachment
N/A
- type Y attachment
N/A
- type Z attachment, if allowed in relevant part 2
N/A
Type X attachment, other than those with a
specially prepared cord, not used for flat twin tinsel
cords
N/A
For multi-phase appliances supplied with a supply
cord and that are intended to be permanently
connected to fixed wiring, the supply cord is
assembled to the appliance by type Y attachment
N/A
A - type Z attachment is allowed for portable fans (IEC
60335-2-80)
25.6
Plugs fitted with only one flexible cord
25.7
Supply cords, other than for class III appliances, being one of the following types:
TRF No. IEC60335_2_80E
N/A
P
Page 41 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
- rubber sheathed (at least 60245 IEC 53)
N/A
- polychloroprene sheathed (at least 60245 IEC 57)
N/A
- cross-linked polyvinyl chloride sheathed (at least
60245 IEC 88)
N/A
- polyvinyl chloride sheathed. Not used if they are likely to touch metal parts having
a temperature rise exceeding 75 K during the test of clause 11
N/A
light polyvinyl chloride sheathed cord
(60227 IEC 52), for appliances not
exceeding 3 kg
H03VVH2-F
P
ordinary polyvinyl chloride sheathed cord
(60227 IEC 53), for other appliances
H05VVH2-F
P
- heat resistant polyvinyl chloride sheathed. Not used for type X attachment other
than specially prepared cords
heat-resistant light polyvinyl chloride
sheathed cord (60227 IEC 56), for
appliances not exceeding 3 kg
N/A
heat-resistant polyvinyl chloride sheathed
cord (60227 IEC 57), for other appliances
N/A
Supply cords for class III appliances adequately
insulated
N/A
Test with 500 V for 2 min for supply cords of class
III appliances that contain live parts
N/A
25.8
Nominal cross-sectional area of supply cords not
0,16A (maximum rated);
less than table 11; rated current (A); cross-sectional 0,75mm²
area (mm²) .............................................................:
25.9
Supply cords not in contact with sharp points or
edges
N/A
25.10
Supply cord of class I appliances have a
green/yellow core for earthing
N/A
25.11
Conductors of supply cords not consolidated by
soldering where they are subject to contact
pressure, unless
N/A
the contact pressure is provided by spring terminals
N/A
25.12
Insulation of the supply cord not damaged when
moulding the cord to part of the enclosure
N/A
25.13
Inlet openings so constructed as to prevent
damage to the supply cord
N/A
If the enclosure at the inlet opening is not of
insulating material, a non-detachable lining or
bushing complying with 29.3 for supplementary
insulation provided
N/A
TRF No. IEC60335_2_80E
P
Page 42 of 101
Report No. 247910
IEC 60335-2-80
Clause
25.14
Requirement - Test
Result - Remark
Verdict
If unsheathed supply cord, a similar additional
bushing or lining is required, unless the appliance is
N/A
class 0, or
N/A
a class III appliance not containing live parts
N/A
Supply cords moved while in operation adequately
protected against excessive flexing
N/A
Flexing test, as described:
- applied force (N)..................................................:
N/A
- number of flexings ...............................................:
N/A
The test does not result in:
25.15
25.16
- short-circuit between the conductors, such that
the current exceeds a value of twice the rated
current
N/A
- breakage of more than 10% of the strands of any
conductor
N/A
- separation of the conductor from its terminal
N/A
- loosening of any cord guard
N/A
- damage to the cord or the cord guard
N/A
- broken strands piercing the insulation and
becoming accessible
N/A
For appliances with supply cord and appliances to
be permanently connected to fixed wiring by a
flexible cord, conductors of the supply cord relieved
from strain, twisting and abrasion by use of cord
anchorage
N/A
The cord cannot be pushed into the appliance to
such an extent that the cord or internal parts of the
appliance can be damaged
N/A
Pull and torque test of supply cord, values shown in
table 12: mass (kg); pull (N); torque (not on
automatic cord reel) (Nm)......................................:
N/A
Cord not damaged and max. 2 mm displacement of
the cord
N/A
Cord anchorages for type X attachments constructed and located so that:
- replacement of the cord is easily possible
N/A
- it is clear how the relief from strain and the
prevention of twisting are obtained
N/A
- they are suitable for different types of supply cord
N/A
- cord cannot touch the clamping screws of cord
anchorage if these screws are accessible, unless
N/A
TRF No. IEC60335_2_80E
Page 43 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
they are separated from accessible metal parts by
supplementary insulation
N/A
- the cord is not clamped by a metal screw which
bears directly on the cord
N/A
- at least one part of the cord anchorage securely
fixed to the appliance, unless
N/A
it is part of a specially prepared cord
N/A
- screws which have to be operated when replacing
the cord do not fix any other component, unless
N/A
the appliance becomes inoperative or incomplete or
the parts cannot be removed without a tool
N/A
- if labyrinths can be bypassed the test of 25.15 is
nevertheless withstood
N/A
- for class 0, 0I and I appliances they are of
insulating material or are provided with an
insulating lining, unless
N/A
failure of the insulation of the cord does not make
accessible metal parts live
N/A
- for class II appliances they are of insulating
material, or
N/A
if of metal, they are insulated from accessible metal
parts by supplementary insulation
N/A
After the test of 25.15, under the conditions
specified, the conductors have not moved by more
than 1 mm in the terminals
N/A
25.17
Adequate cord anchorages for type Y and Z
attachment, test with the cord supplied with the
appliance
N/A
25.18
Cord anchorages only accessible with the aid of a
tool, or
N/A
Constructed so that the cord can only be fitted with
the aid of a tool
N/A
Type X attachment, glands not used as cord
anchorage in portable appliances
N/A
Tying the cord into a knot or tying the cord with
string not used
N/A
25.20
The insulated conductors of the supply cord for
type Y and Z attachment additionally insulated from
accessible metal parts
N/A
25.21
Space for supply cord for type X attachment or for connection of fixed wiring
constructed:
25.19
TRF No. IEC60335_2_80E
Page 44 of 101
Report No. 247910
IEC 60335-2-80
Clause
25.22
Requirement - Test
Result - Remark
Verdict
- to permit checking of conductors with respect to
correct positioning and connection before fitting any
cover
N/A
- so there is no risk of damage to the conductors or
their insulation when fitting the cover
N/A
- for portable appliances, so that the uninsulated
end of a conductor, if it becomes free from the
terminal, prevented from contact with accessible
metal parts
N/A
2 N test to the conductor for portable appliances;
no contact with accessible metal parts
N/A
Appliance inlets:
- live parts not accessible during insertion or
removal
N/A
Requirement not applicable to appliance inlets
complying with IEC 60320-1
P
- connector can be inserted without difficulty
P
- the appliance is not supported by the connector
P
- not for cold conditions if temp. rise of external
metal parts exceeds 75 K during clause 11, unless
N/A
the supply cord is unlikely to touch such metal parts
N/A
Interconnection cords comply with the requirements
for the supply cord, except that:
N/A
- the cross-sectional area of the conductors is
determined on the basis of the maximum current
during clause 11
N/A
- the thickness of the insulation may be reduced
N/A
If necessary, electric strength test of 16.3
N/A
25.24
Interconnection cords not detachable without the
aid of a tool if compliance with this standard is
impaired when they are disconnected
N/A
25.25
Dimensions of pins that are inserted into socketoutlets compatible with the dimensions of the
relevant socket-outlet.
N/A
Dimensions of pins and engagement face in
accordance with the dimensions of the relevant
plug in IEC/TR 60083
N/A
25.23
26
TERMINALS FOR EXTERNAL CONDUCTORS
26.1
Appliances provided with terminals or equally
effective devices for connection of external
conductors
TRF No. IEC60335_2_80E
P
Page 45 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Terminals only accessible after removal of a nondetachable cover, except
26.2
26.3
Verdict
P
for class III appliances that do not contain live parts
N/A
Earthing terminals may be accessible if a tool is
required to make the connections and means are
provided to clamp the wire independently from its
connection
N/A
Appliances with type X attachment and appliances
for the connection of cables to fixed wiring provided
with terminals in which connections are made by
means of screws, nuts or similar devices, unless
N/A
the connections are soldered
N/A
Screws and nuts not used to fix any other
component, except
N/A
internal conductors, if so arranged that they are
unlikely to be displaced when fitting the supply
conductors
N/A
If soldered connections used, the conductor so
positioned or fixed that reliance is not placed on
soldering alone, unless
N/A
barriers provided so that neither clearances nor
creepage distances between live parts and other
metal parts reduced below the values for
supplementary insulation if the conductor becomes
free at the soldered joint
N/A
Terminals for type X attachment and for connection
of cables of fixed wiring so constructed that the
conductor is clamped between metal surfaces with
sufficient contact pressure but without damaging
the conductor
N/A
Terminals fixed so that when the clamping means is tightened or loosened:
- the terminal does not become loose
N/A
- internal wiring is not subjected to stress
N/A
- neither clearances nor creepage distances are
reduced below the values in clause 29
N/A
Compliance checked by inspection and by the test
of subclause 9.6 of IEC 60999-1, the torque applied
being equal to two-thirds of the torque specified
(Nm).......................................................................:
N/A
No deep or sharp indentations of the conductors
N/A
TRF No. IEC60335_2_80E
Page 46 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
26.4
Terminals for type X attachment, except those
having a specially prepared cord and those for the
connection of cables of fixed wiring, no special
preparation of conductors such as by soldering, use
of cable lugs, eyelets or similar, and
N/A
so constructed or placed that conductors prevented
from slipping out when clamping screws or nuts are
tightened
N/A
Terminals for type X attachment so located or
shielded that if a wire of a stranded conductor
escapes, no risk of accidental connection to other
parts that result in a hazard
N/A
Stranded conductor test, 8 mm insulation removed
N/A
No contact between live parts and accessible metal
parts and,
N/A
for class II constructions, between live parts and
metal parts separated from accessible metal parts
by supplementary insulation only
N/A
Terminals for type X attachment and for connection
of cables of fixed wiring suitable for connection of
conductors with cross-sectional area according to
table 13; rated current (A); nominal cross-sectional
area (mm²) .............................................................:
N/A
If a specially prepared cord is used, terminals need
only be suitable for that cord
N/A
26.7
Terminals for type X attachment, except in class III
appliances not containing live parts, accessible
after removal of a cover or part of the enclosure
N/A
26.8
Terminals for the connection of fixed wiring,
including the earthing terminal, located close to
each other
N/A
26.9
Terminals of the pillar type constructed and located
as specified
N/A
26.10
Terminals with screw clamping and screwless
terminals not used for flat twin tinsel cords, unless
N/A
conductors ends fitted with means suitable for
screw terminals
N/A
Pull test of 5 N to the connection
N/A
For type Y and Z attachment, soldered, welded,
crimped or similar connections may be used
N/A
For Class II appliances, the conductor so
positioned or fixed that reliance is not placed on
soldering, welding or crimping alone
N/A
26.5
26.6
26.11
TRF No. IEC60335_2_80E
Result - Remark
Verdict
Page 47 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
If soldering, welding or crimping alone used,
barriers provided so that clearances and creepage
distances between live parts and other metal parts
are not reduced below the values for
supplementary insulation if the conductor becomes
free
Result - Remark
Verdict
N/A
27
PROVISION FOR EARTHING
27.1
Accessible metal parts of Class 0I and I appliances
permanently and reliably connected to an earthing
terminal or earthing contact of the appliance inlet
N/A
Earthing terminals and earthing contacts not
connected to the neutral terminal
N/A
Class 0, II and III appliances have no provision for
earthing
27.2
27.3
27.4
P
Safety extra-low voltage circuits not earthed, unless
N/A
protective extra-low voltage circuits
N/A
Clamping means of earthing terminals adequately
secured against accidental loosening
N/A
Terminals for the connection of external
equipotential bonding conductors allow connection
of conductors of 2.5 to 6 mm², and
N/A
do not provide earthing continuity between different
parts of the appliance, and
N/A
conductors cannot be loosened without the aid of a
tool
N/A
For a detachable part having an earth connection
and being plugged into another part of the
appliance, the earth connection is made before and
separated after current-carrying connections when
removing the part
N/A
For appliances with supply cords, current-carrying
conductors become taut before earthing conductor,
if the cord slips out of the cord anchorage
N/A
No risk of corrosion resulting from contact between
parts of the earthing terminal and the copper of the
earthing conductor or other metal
N/A
Parts providing earthing continuity, other than parts
of a metal frame or enclosure, have adequate
resistance to corrosion
N/A
If of steel, these parts provided with an
electroplated coating with a thickness at least 5 µm
N/A
TRF No. IEC60335_2_80E
Page 48 of 101
Report No. 247910
IEC 60335-2-80
Clause
27.5
27.6
Requirement - Test
Result - Remark
Verdict
Adequate protection against rusting of parts of
coated or uncoated steel, only intended to provide
or transmit contact pressure
N/A
In the body of the earthing terminal is a part of a
frame or enclosure of aluminium or aluminium
alloys, precautions taken to avoid risk of corrosion
N/A
Low resistance of connection between earthing
terminal and earthed metal parts
N/A
This requirement does not apply to connections
providing earthing continuity in the protective extralow voltage circuit, provided the clearances of basic
insulation are based on the rated voltage of the
appliance
N/A
Resistance not exceeding 0,1 at the specified
low-resistance test ( ) .........................................:
N/A
The printed conductors of printed circuit boards not
used to provide earthing continuity in hand-held
appliances.
N/A
They may be used to provide earthing continuity in
other appliances if at least two tracks are used with
independent soldering points and the appliance
complies with 27.5 for each circuit
N/A
28
SCREWS AND CONNECTIONS
28.1
Fixings, electrical connections and connections
providing earthing continuity withstand mechanical
stresses
P
Screws not of soft metal liable to creep, such as
zinc or aluminium
P
Diameter of screws of insulating material min.
3 mm
N/A
Screws of insulating material not used for any
electrical connections or connections providing
earthing continuity
N/A
Screws used for electrical connections or
connections providing earthing continuity screwed
into metal
N/A
Screws not of insulating material if their
replacement by a metal screw can impair
supplementary or reinforced insulation
N/A
For type X attachment, screws to be removed for
replacement of supply cord or for user
maintenance, not of insulating material if their
replacement by a metal screw impairs basic
insulation
N/A
TRF No. IEC60335_2_80E
Page 49 of 101
Report No. 247910
IEC 60335-2-80
Clause
28.2
Requirement - Test
Result - Remark
Verdict
For screws and nuts; torque-test as specified in
table 14 ..................................................................:
N/A
Electrical connections and connections providing
earthing continuity constructed so that contact
pressure is not transmitted through non-ceramic
insulating material liable to shrink or distort, unless
N/A
there is resiliency in the metallic parts to
compensate for shrinkage or distortion of the
insulating material
N/A
This requirement does not apply to electrical connections in circuits of appliances
for which:
28.3
30.2.2 is applicable and that carry a current
not exceeding 0,5 A
N/A
30.2.3 is applicable and that carry a current
not exceeding 0,2 A
N/A
Space-threaded (sheet metal) screws only used for
electrical connections if they clamp the parts
together
N/A
Thread-cutting (self-tapping) screws and thread
rolling screws only used for electrical connections if
they generate a full form standard machine screw
thread
N/A
Thread-cutting (self-tapping) screws not used if
they are likely to be operated by the user or
installer
N/A
Thread-cutting, thread rolling and space threaded screws may be used in
connections providing earthing continuity provided it is not necessary to disturb the
connection:
28.4
- in normal use,
N/A
- during user maintenance,
N/A
- when replacing a supply cord having a type X
attachment, or
N/A
- during installation
N/A
At least two screws being used for each connection
providing earthing continuity, unless
N/A
the screw forms a thread having a length of at least
half the diameter of the screw
N/A
Screws and nuts that make mechanical connection
secured against loosening if they also make
electrical connections or connections providing
earthing continuity
N/A
This requirement does not apply to screws in the
earthing circuit if at least two screws are used, or
N/A
TRF No. IEC60335_2_80E
Page 50 of 101
Report No. 247910
IEC 60335-2-80
Clause
29
Requirement - Test
Result - Remark
if an alternative earthing circuit is provided
N/A
Rivets for electrical connections or connections
providing earthing continuity secured against
loosening if the connections are subjected to
torsion
N/A
CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION
Clearances, creepage distances and solid
insulation withstand electrical stress
29.1
P
For coatings used on printed circuits boards to
protect the microenvironment (Type 1) or to provide
basic insulation (Type 2), Annex J applies ............:
N/A
The microenvironment is pollution degree 1 under
type 1 protection
N/A
For type 2 protection, the spacing between the
conductors before the protection is applied is not
less than the values specified in Table 1 of IEC
60664-3
N/A
These values apply to functional, basic,
supplementary and reinforced insulation ..............:
N/A
Clearances not less than the values specified in
table 16, taking into account the rated impulse
voltage for the overvoltage categories of table 15,
unless ....................................................................:
(see appended table)
P
for basic insulation and functional insulation they
comply with the impulse voltage test of clause 14
N/A
However, if the distances are affected by wear,
distortion, movement of the parts or during
assembly, the clearances for rated impulse
voltages of 1500V and above are increased by 0,5
mm and the impulse voltage test is not applicable
N/A
Impulse voltage test is not applicable:
N/A
- when the microenvironment is pollution degree 3,
or
- for basic insulation of class 0 and class 01
appliances
29.1.1
Verdict
P
N/A
Appliances are in overvoltage category II
P
A force of 2 N is applied to bare conductors, other
than heating elements
P
A force of 30 N is applied to accessible surfaces
P
Clearances of basic insulation withstand the
overvoltages, taking into account the rated impulse
voltage
P
TRF No. IEC60335_2_80E
Page 51 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
The values of table 16 or the impulse voltage test of (see appended table)
clause 14 are applicable........................................:
Clearance at the terminals of tubular sheathed
heating elements may be reduced to 1,0 mm if the
microenvironment is pollution degree 1
Verdict
P
N/A
Lacquered conductors of windings considered to be
bare conductors
P
29.1.2
Clearances of supplementary insulation not less
(see appended table)
than those specified for basic insulation in table 16:
P
29.1.3
Clearances of reinforced insulation not less than
(see appended table)
those specified for basic insulation in table 16,
using the next higher step for rated impulse voltage
...............................................................................:
P
For double insulation, with no intermediate
conductive part between basic and supplementary
insulation, clearances are measured between live
parts and the accessible surface, and the insulation
system is treated as reinforced insulation
P
29.1.4
Clearances for functional insulation are the largest values determined from:
- table 16 based on the rated impulse voltage ......:
(see appended table)
- table F.7a in IEC 60664-1, frequency not
exceeding 30 kHz
P
- clause 4 of IEC 60664-4, frequency exceeding 30
kHz
N/A
If values of table 16 are largest, the impulse voltage
test of clause 14 may be applied instead, unless
N/A
the microenvironment is pollution degree 3, or
P
the distances can be affected by wear, distortion,
movement of the parts or during assembly
N/A
However, clearances are not specified if the
appliance complies with clause 19 with the
functional insulation short-circuited
N/A
Lacquered conductors of windings considered to be
bare conductors
P
However, clearances at crossover points are not
measured
P
Clearance between surfaces of PTC heating
elements may be reduced to 1mm
29.1.5
P
N/A
Appliances having higher working voltages than rated voltage, clearances for basic
insulation are the largest values determined from:
- table 16 based on the rated impulse voltage ......:
TRF No. IEC60335_2_80E
N/A
Page 52 of 101
Report No. 247910
IEC 60335-2-80
Clause
29.2
Requirement - Test
Result - Remark
Verdict
- table F.7a in IEC 60664-1, frequency not
exceeding 30 kHz
N/A
- clause 4 of IEC 60664-4, frequency exceeding 30
kHz
N/A
If clearances for basic insulation are selected from
Table F.7a of IEC 60664-1 or Clause 4 of IEC
60664-4, the clearances of supplementary
insulation are not less than those specified for basic
insulation
N/A
If clearances for basic insulation are selected from
Table F.7a of IEC 60664-1, the clearances of
reinforced insulation dimensioned as specified in
Table F.7a are to withstand 160% of the withstand
voltage required for basic insulation
N/A
If clearances for basic insulation are selected from
Clause 4 of IEC 60664-4, the clearances of
reinforced insulation are twice the value required
for basic insulation
N/A
If the secondary winding of a step-down
transformer is earthed, or if there is an earthed
screen between the primary and secondary
windings, clearances of basic insulation on the
secondary side not less than those specified in
table 16, but using the next lower step for rated
impulse voltage
N/A
Circuits supplied with a voltage lower than rated
voltage, clearances of functional insulation are
based on the working voltage used as the rated
voltage in table 15
P
Creepage distances not less than those appropriate (see appended table)
for the working voltage, taking into account the
material group and the pollution degree................:
P
Pollution degree 2 applies, unless
N/A
- precautions taken to protect the insulation;
pollution degree 1
N/A
- insulation subjected to conductive pollution;
pollution degree 3
P
A Microenvironment is pollution degree 3 unless
insulation is enclosed or located that it is unlikely to
be exposed to pollution during normal use. (IEC
60335-2-80)
P
A force of 2 N is applied to bare conductors, other
than heating elements
P
A force of 30 N is applied to accessible surfaces
P
TRF No. IEC60335_2_80E
Page 53 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
In a double insulation system, the working voltage
for both the basic and supplementary insulation is
taken as the working voltage across the complete
double insulation system
29.2.1
29.2.2
Creepage distances of basic insulation not less
than specified in table 17.......................................:
P
(see appended table)
N/A
Except for pollution degree 1, corresponding
creepage distance not less than the minimum
specified for the clearance in table 16, if the
clearance has been checked according to the test
of clause 14 ...........................................................:
N/A
Creepage distances of supplementary insulation at (see appended table)
least those specified for basic insulation in table 17,
or ...........................................................................:
Creepage distances of reinforced insulation at least (see appended table)
double those specified for basic insulation in table
17, or .....................................................................:
Table 2 of IEC 60664-4, as applicable ..................:
29.2.4
29.3
P
However, if the working voltage is periodic and has
a frequency exceeding 30 kHz, the creepage
distances are also determined from table 2 of IEC
60664-4, these values being used if exceeding the
values in table 17 ..................................................:
Table 2 of IEC 60664-4, as applicable ..................:
29.2.3
Verdict
Creepage distances of functional insulation not less (see appended table)
than specified in table 18.......................................:
P
N/A
P
N/A
P
However, if the working voltage is periodic and has
a frequency exceeding 30 kHz, the creepage
distances are also determined from table 2 of IEC
60664-4, these values being used if exceeding the
values in table 18 ..................................................:
N/A
Creepage distances may be reduced if the
appliance complies with clause 19 with the
functional insulation short-circuited
N/A
Supplementary and reinforced insulation have
adequate thickness, or a sufficient number of
layers, to withstand the electrical stresses
P
Compliance checked:
- by measurement, in accordance with 29.3.1, or
P
- by an electric strength test in accordance with
29.3.2, or
N/A
- by an assessment of the thermal quality of the
material combined with an electric strength test, in
accordance with 29.3.3, and
N/A
TRF No. IEC60335_2_80E
Page 54 of 101
Report No. 247910
IEC 60335-2-80
Clause
29.3.1
29.3.2
Requirement - Test
Result - Remark
Verdict
for accessible parts of reinforced insulation
consisting of a single layer, by measurement in
accordance with 29.3.4, or
N/A
- as specified in subclause 6.3 of IEC 60664-4 for
insulation that is subjected to any periodic voltage
having a frequency exceeding 30 kHz
N/A
Supplementary insulation have a thickness of at
least 1 mm
P
Reinforced insulation have a thickness of at least 2
mm
P
Each layer of material withstand the electric
strength test of 16.3 for supplementary insulation
N/A
Supplementary insulation consist of at least 2
layers
N/A
Reinforced insulation consist of at least 3 layers
N/A
The insulation is subjected to the dry heat test Bb
of IEC 60068-2-2, followed by
N/A
the electric strength test of 16.3
N/A
If the temperature rise during the tests of clause 19
does not exceed the value specified in table 3, the
test of IEC 60068-2-2 is not carried out
N/A
29.3.4
Thickness of accessible parts of reinforced
insulation consisting of a single layer not less than
specified in table 19...............................................:
N/A
30
RESISTANCE TO HEAT AND FIRE
30.1
External parts of non-metallic material,
P
parts supporting live parts, and
P
parts of thermoplastic material providing
supplementary or reinforced insulation
P
sufficiently resistant to heat
P
Ball-pressure test according to IEC 60695-10-2
P
29.3.3
External parts tested at 40 C plus the maximum
temperature rise determined during the test of
clause 11, or at 75 C, whichever is the higher;
temperature ( C)....................................................:
(see appended table)
P
Parts supporting live parts tested at 40 C plus the
maximum temperature rise determined during the
test of clause 11, or at 125 C, whichever is the
higher; temperature ( C) .......................................:
(see appended table)
P
TRF No. IEC60335_2_80E
Page 55 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Parts of thermoplastic material providing
supplementary or reinforced insulation tested at 25
C plus the maximum temperature rise determined
during clause 19, if higher; temperature ( C) ........:
30.2
Parts of non-metallic material resistant to ignition
and spread of fire
Result - Remark
Verdict
N/A
P
This requirement does not apply to:
parts having a mass not exceeding 0,5 g, provided
the cumulative effect is unlikely to propagate flames
that originate inside the appliance by propagating
flames from one part to another, or
30.2.1
N/A
decorative trims, knobs and other parts unlikely to
be ignited or to propagate flames that originate
inside the appliance
P
Compliance checked by the tests of 30.2.1 and
30.2.3
P
For base material of printed circuit boards, 30.2.4
applies
P
Parts of non-metallic material subjected to the
glow-wire test of IEC 60695-2-11 at 550 C
P
However, test not carried out if the material is
classified as having a glow-wire flammability index
according to IEC 60695-2-12 of at least 550 C, or
N/A
the material is classified at least HB40 according to
IEC 60695-11-10
N/A
Parts for which the glow-wire test cannot be carried
out need to meet the requirements in ISO 9772 for
material classified HBF
N/A
30.2.2
Not applicable. (IEC 60335-2-80)
N/A
30.2.3
Appliances operated while unattended, tested as
specified in 30.2.3.1 and 30.2.3.2
P
The tests are not applicable to conditions as
specified ................................................................:
N/A
Parts of non-metallic material supporting
connections carrying a current exceeding 0,2 A
during normal operation, and
N/A
parts of non-metallic material, other than small
parts, within a distance of 3 mm,
N/A
subjected to the glow-wire test of IEC 60695-2-11
with a test severity of 850 °C
N/A
Glow-wire applied to an interposed shielding
material, if relevant
N/A
30.2.3.1
TRF No. IEC60335_2_80E
Page 56 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
The glow-wire test is not carried out on parts of
material classified as having a glow-wire
flammability index according to IEC 60695-2-12 of
at least 850 °C
30.2.3.2
Verdict
N/A
Parts of non-metallic material supporting
connections, and
P
parts of non-metallic material within a distance of
3mm,
P
subjected to glow-wire test of IEC 60695-2-11
P
The test severity is:
- 750 C, for connections carrying a current
exceeding 0,2 A during normal operation
- 650 C, for other connections
Glow-wire applied to an interposed shielding
material, if relevant
N/A
P
N/A
However, the glow-wire test of 750 C or 650 C as appropriate, is not carried out
on parts of material fulfilling both or either of the following classifications:
- a glow-wire ignition temperature according to IEC
60695-2-13 of at least:
N/A
775 C, for connections carrying a current
exceeding 0,2 A during normal operation
N/A
675 C, for other connections
N/A
- a glow-wire flammability index according to IEC
60695-2-12 of at least:
N/A
- 750 C, for connections carrying a current
exceeding 0,2 A during normal operation
N/A
- 650 C, for other connections
N/A
The glow-wire test is also not carried out on small parts. These parts are to:
- comprise material having a glow-wire ignition
temperature of at least 775 C or 675 C as
appropriate, or
N/A
- comprise material having a glow-wire flammability
index of at least 750 C or 650 C as appropriate,
or
N/A
- comply with the needle-flame test of Annex E, or
N/A
- comprise material classified as V-0 or V-1
according to IEC 60695-11-10
N/A
TRF No. IEC60335_2_80E
Page 57 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
The consequential needle-flame test of Annex E applied to non-metallic parts that
encroach within the vertical cylinder placed above the centre of the connection zone
and on top of the non-metallic parts supporting current-carrying connections, and
parts of non-metallic material within a distance of 3 mm of such connections if these
parts are those:
- parts that withstood the glow-wire test of IEC
60695-2-11 of 750 C or 650 C as appropriate, but
produce a flame that persist longer than 2 s, or
N/A
- parts that comprised material having a glow-wire
flammability index of at least 750 C or 650 C as
appropriate, or
N/A
- small parts, that comprised material having a
glow-wire flammability index of at least 750 C or
650 C as appropriate, or
N/A
- small parts for which the needle-flame test of
Annex E was applied, or
N/A
- small parts for which a material classification of V0 or V-1 was applied
N/A
However, the consequential needle-flame test is not carried out on non-metallic
parts, including small parts, within the cylinder that are:
30.2.4
- parts having a glow-wire ignition temperature of at
least 775 C or 675 C as appropriate, or
N/A
- parts comprising material classified as V-0 or V-1
according to IEC 60695-11-10, or
N/A
- parts shielded by a flame barrier that meets the
needle-flame test of Annex E or that comprises
material classified as V-0 or V-1 according to IEC
60695-11-10
N/A
Base material of printed circuit boards subjected to
the needle-flame test of Annex E
N/A
Test not applicable to conditions as specified .......:
31
P
RESISTANCE TO RUSTING
Relevant ferrous parts adequately protected
against rusting
Tests specified in part 2 when necessary
32
V-0
P
N/A
RADIATION, TOXICITY AND SIMILAR HAZARDS
Appliance does not emit harmful radiation or
present a toxic or similar hazard due to their
operation in normal use
P
Compliance is checked by the limits or tests
specified in part 2, if relevant
N/A
TRF No. IEC60335_2_80E
Page 58 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
A
ANNEX A (INFORMATIVE)
ROUTINE TESTS
Result - Remark
Description of routine tests to be carried out by the
manufacturer
B
N/A
ANNEX B (NORMATIVE)
APPLIANCES POWERED BY RECHARGEABLE BATTERIES
The following modifications to this standard are
applicable for appliances powered by batteries that
are recharged in the appliance
This annex does not apply to battery chargers
3.1.9
Verdict
P
N/A
Appliance operated under the following conditions:
- the appliance, supplied by its fully charged
battery, operated as specified in relevant part 2
P
- the battery is charged, the battery being initially
discharged to such an extent that the appliance
cannot operate
P
-if possible, the appliance is supplied from the
supply mains through its battery charger, the
battery being initially discharged to such an extent
that the appliance cannot operate. The appliance is
operated as specified in relevant part 2
P
- if the appliance incorporates inductive coupling
between two parts that are detachable from each
other, the appliance is supplied from the supply
mains with the detachable part removed
N/A
3.6.2
Part to be removed in order to discard the battery is
not considered to be detachable
P
5.B.101
Appliances supplied from the supply mains tested
as specified for motor-operated appliances
P
7.1
Battery compartment for batteries intended to be
replaced by the user, marked with battery voltage
and polarity of the terminals
N/A
The positive terminal indicated by symbol IEC
60417-5005 and the negative terminal by symbol
IEC 60417-5006
N/A
7.6
Symbols 60417-5005 and IEC 60417-5006
N/A
7.12
The instructions give information regarding
charging
P
The instructions for appliances incorporating
batteries intended to be replaced by the user
includes required information
Details about how to remove batteries containing
materials hazardous to the environment given
TRF No. IEC60335_2_80E
N/A
P
Page 59 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
7.15
Markings placed on the part of the appliance
connected to the supply mains
8.2
Appliances having batteries that according to the
instruction may be replaced by the user need only
have basic insulation between live parts and the
inner surface of the battery compartment
N/A
If the appliance can be operated without batteries,
double or reinforced insulation required
P
11.7
The battery is charged for the period stated in the
instructions or 24 h ................................................:
P
19.1
Appliances subjected to tests of 19.B.101, 19.B.102
and 19.B.103
P
19.10
Not applicable
19.B.101
Appliances supplied at rated voltage for 168 h, the
battery being continually charged
P
19.B.102
For appliances having batteries that can be
removed without the aid of a tool, short-circuit of
the terminals of the battery, the battery being fully
charged,
N/A
19.B.103
Appliances having batteries replaceable by the user
supplied at rated voltage under normal operation
with the battery removed or in any position allowed
by the construction
N/A
21.B.101
Appliances having pins for insertion into socketoutlets have adequate mechanical strength
N/A
P
N/A
Part of the appliance incorporating the pins subjected to the free fall test, procedure
2, of IEC 60068-2-31, the number of falls being:
- 100, if the mass of the part does not exceed 250 g
(g) ..........................................................................:
N/A
- 50, if the mass of the part exceeds 250 g ...........:
N/A
After the test, the requirements of 8.1, 15.1.1, 16.3
and clause 29 are met
N/A
22.3
Appliances having pins for insertion into socketoutlets tested as fully assembled as possible
N/A
25.13
An additional lining or bushing not required for
interconnection cords in class III appliances or
class III constructions operating at safety extra-low
voltage not containing live parts
N/A
30.2
For parts of the appliance connected to the supply
mains during the charging period, 30.2.3 applies
P
For other parts, 30.2.2 applies
TRF No. IEC60335_2_80E
N/A
Page 60 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
C
ANNEX C (NORMATIVE)
AGEING TEST ON MOTORS
D
E
Result - Remark
Tests, as described, carried out when doubt with
regard to the temperature classification of the
insulation of a motor winding
N/A
Test conditions as specified
N/A
ANNEX D (NORMATIVE)
THERMAL MOTOR PROTECTORS
Applicable to appliances having motors that
incorporate thermal motor protectors necessary for
compliance with the standard
N/A
Test conditions as specified
N/A
ANNEX E (NORMATIVE)
NEEDLE-FLAME TEST
Needle-flame test carried out in accordance with IEC 60695-11-5, with the following
modifications:
7
Verdict
N/A
Severities
The duration of application of the test flame is
30 s ± 1 s
N/A
9
Test procedure
9.1
The specimen so arranged that the flame can be
applied to a vertical or horizontal edge as shown in
the examples of Figure 1
N/A
9.2
The first paragraph does not apply
N/A
If possible, the flame is applied at least 10 mm from
a corner
N/A
The test is carried out on one specimen
N/A
If the specimen does not withstand the test, the test
may be repeated on two additional specimens, both
withstanding the test
N/A
9.3
11
F
Evaluation of test results
The duration of burning not exceeding 30 s
N/A
However, for printed circuit boards, the duration of
burning not exceeding 15 s
N/A
ANNEX F (NORMATIVE)
CAPACITORS
Capacitors likely to be permanently subjected to the supply voltage, and used for
radio interference suppression or voltage dividing, comply with the following clauses
of IEC 60384-14, with the following modifications:
1.5
Terms and definitions
TRF No. IEC60335_2_80E
N/A
Page 61 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
1.5.3
Class X capacitors tested according to subclass X2
N/A
1.5.4
This subclause is applicable
N/A
1.6
Marking
Items a) and b) are applicable
Verdict
N/A
3.4
Approval testing
3.4.3.2
Table 3 is applicable as described
N/A
4.1
Visual examination and check of dimensions
N/A
This subclause is applicable
N/A
4.2
Electrical tests
4.2.1
This subclause is applicable
N/A
4.2.5
This subclause is applicable
N/A
4.2.5.2
Only table 11 is applicable
N/A
Values for test A apply
N/A
However, for capacitors in heating appliances the
values for test B or C apply
N/A
4.12
4.13
Damp heat, steady state
This subclause is applicable
N/A
Only insulation resistance and voltage proof are
checked
N/A
Impulse voltage
This subclause is applicable
4.14
4.14.7
4.17
Endurance
Subclauses 4.14.1, 4.14.3, 4.14.4 and 4.14.7 are
applicable
N/A
Only insulation resistance and voltage proof are
checked
N/A
No visible damage
N/A
Passive flammability test
This subclause is applicable
4.18
N/A
Active flammability test
This subclause is applicable
G
N/A
ANNEX G (NORMATIVE)
SAFETY ISOLATING TRANSFORMERS
The following modifications to this standard are applicable for safety isolating
transformers:
TRF No. IEC60335_2_80E
N/A
Page 62 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
7
Marking and instructions
7.1
Transformers for specific use marked with:
17
Result - Remark
-name, trademark or identification mark of the
manufacturer or responsible vendor .....................:
Manufacture: Kennede
Electronics Mfg. Co., Ltd.
P
-model or type reference .......................................:
EI66X28; EI57X25; EI48X28
P
Overload protection of transformers and associated circuits
Fail-safe transformers comply with subclause 15.5
of IEC 61558-1
22
N/A
Construction
Subclauses 19.1 and 19.1.2 of IEC 61558-2-6 are
applicable
29
P
Clearances, creepage distances and solid insulation
29.1, 29.2, The distances specified in items 2a, 2c and 3 in
29.3
table 13 of IEC 61558-1 apply
H
Verdict
Cr: 13,6mm Cl: 12mm
Solid insulation: 1,8mm
P
For insulated winding wires complying with
subclause 19.12.3 of IEC 61558-1 there are no
requirements for clearances or creepage distances
N/A
For windings providing reinforced insulation, the
distance specified in item 2c of table 13 of IEC
61558-1 is not assessed
N/A
For safety isolating transformers subjected to
periodic voltages with a frequency exceeding 30
kHz, the clearances, creepage distances and solid
insulation values specified in IEC 60664-4 are
applicable, if greater than the values specified in
items 2a, 2c and 3 in table 13 of IEC 61558-1
N/A
ANNEX H (NORMATIVE)
SWITCHES
Switches comply with the following clauses of IEC 61058-1, as modified below:
The tests of IEC 61058-1 carried out under the
conditions occurring in the appliance
Before being tested, switches are operated 20
times without load
8
P
P
Marking and documentation
Switches are not required to be marked
However, a switch that can be tested separately
from the appliance marked with the manufacturer’s
name or trade mark and the type reference
13
SS22F25G7, S22F25G9
P
N/A
Mechanism
The tests may be carried out on a separate sample
TRF No. IEC60335_2_80E
P
Page 63 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
15
Insulation resistance and dielectric strength
15.1
Not applicable
P
15.2
Not applicable
P
15.3
Applicable for full disconnection and microdisconnection
P
17
Endurance
20
Result - Remark
Compliance is checked on three separate
appliances or switches
P
For 17.2.4.4, the number of cycles declared
according to 7.1.4 is 10 000, unless
P
otherwise specified in 24.1.3 of the relevant part 2
of IEC 60335 .........................................................:
N/A
Switches for operation under no load and which
can be operated only by a tool, and
N/A
switches operated by hand that are interlocked so
that they cannot be operated under load,
N/A
are not subjected to the tests
N/A
However, switches without this interlock are
subjected to the test of 17.2.4.4 for 100 cycles of
operation
N/A
Subclauses 17.2.2 and 17.2.5.2 not applicable
P
The ambient temperature during the test is that
occurring in the appliance during the test of Clause
11 in IEC 60335-1
P
The temperature rise of the terminals not more than 16,5K < 30K
30 K above the temperature rise measured in
clause 11 of IEC 60335-1 (K) ................................:
P
Clearances, creepage distances, solid insulation and coatings of rigid printed board
assemblies
This clause is applicable to clearances and
creepage distances for functional insulation, across
full disconnection and micro-disconnection, as
stated in table 24
I
Verdict
P
ANNEX I (NORMATIVE)
MOTORS HAVING BASIC INSULATION THAT IS INADEQUATE FOR THE
RATED VOLTAGE OF THE APPLIANCE
The following modifications to this standard are applicable for motors having basic
insulation that is inadequate for the rated voltage of the appliance:
8
Protection against access to live parts
8.1
Metal parts of the motor are considered to be bare
live parts
TRF No. IEC60335_2_80E
For models KN-2903 & KN2905
P
P
Page 64 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
11
Heating
11.3
The temperature rise of the body of the motor is
determined instead of the temperature rise of the
windings
P
11.8
The temperature rise of the body of the motor,
where in contact with insulating material, not
exceeding values in table 3 for the relevant
insulating material
P
16
Leakage current and electric strength
16.3
Insulation between live parts of the motor and its
other metal parts is not subjected to the test
19
Abnormal operation
19.1
The tests of 19.7 to 19.9 are not carried out
19.I.101
Appliance operated at rated voltage with each of the following fault conditions:
P
P
- short circuit of the terminals of the motor,
including any capacitor incorporated in the motor
circuit
P
- short circuit of each diode of the rectifier
P
- open circuit of the supply to the motor
P
- open circuit of any parallel resistor, the motor
being in operation
Only one fault simulated at a time, the tests carried
out consecutively
N/A
P
22
Construction
22.I.101
For class I appliances incorporating a motor
supplied by a rectifier circuit, the d.c. circuit being
insulated from accessible parts of the appliance by
double or reinforced insulation
N/A
Compliance checked by the tests specified for
double and reinforced insulation
N/A
J
ANNEX J (NORMATIVE)
COATED PRINTED CIRCUIT BOARDS
Testing of protective coatings of printed circuit boards carried out in accordance
with IEC 60664-3 with the following modifications:
5.7
Conditioning of the test specimens
When production samples are used, three samples
of the printed circuit board are tested
5.7.1
N/A
N/A
Cold
The test is carried out at -25 C
TRF No. IEC60335_2_80E
N/A
Page 65 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
5.7.3
Rapid change of temperature
N/A
Severity 1 is specified
N/A
5.9
Result - Remark
Additional tests
This subclause is not applicable
K
L
N/A
ANNEX K (NORMATIVE)
OVERVOLTAGE CATEGORIES
The information on overvoltage categories is
extracted from IEC 60664-1
P
Overvoltage category is a numeral defining a
transient overvoltage condition
P
Equipment of overvoltage category IV is for use at
the origin of the installation
N/A
Equipment of overvoltage category III is equipment
in fixed installations and for cases where the
reliability and the availability of the equipment is
subject to special requirements
N/A
Equipment of overvoltage category II is energy
consuming equipment to be supplied from the fixed
installation
P
If such equipment is subjected to special
requirements with regard to reliability and
availability, overvoltage category III applies
N/A
Equipment of overvoltage category I is equipment
for connection to circuits in which measures are
taken to limit transient overvoltages to an
appropriate low level
N/A
ANNEX L (INFORMATIVE)
GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES
Information for the determination of clearances and
creepage distances
M
Verdict
P
ANNEX M (NORMATIVE)
POLLUTION DEGREE
The information on pollution degrees is extracted
from IEC 60664-1
P
Pollution
The microenvironment determines the effect of
pollution on the insulation, taking into account the
macroenvironment
P
Means may be provided to reduce pollution at the
insulation by effective enclosures or similar
N/A
TRF No. IEC60335_2_80E
Page 66 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Minimum clearances specified where pollution may
be present in the microenvironment
Verdict
P
Degrees of pollution in the microenvironment
For evaluating creepage distances, the following degrees of pollution in the
microenvironment are established:
N
- pollution degree 1: no pollution or only dry, nonconductive pollution occurs. The pollution has no
influence
N/A
- pollution degree 2: only non-conductive pollution
occurs, except that occasionally a temporary
conductivity caused by condensation is to be
expected
N/A
- pollution degree 3: conductive pollution occurs or
dry non-conductive pollution occurs that becomes
conductive due to condensation that is to be
expected
P
- pollution degree 4: the pollution generates
persistent conductivity caused by conductive dust
or by rain or snow
N/A
ANNEX N (NORMATIVE)
PROOF TRACKING TEST
The proof tracking test is carried out in accordance with IEC 60112 with the
following modifications:
7
Test apparatus
7.3
Test solutions
Test solution A is used
10
Determination of proof tracking index (PTI)
10.1
Procedure
The proof voltage is 100V, 175V, 400V or 600V ...:
P
175V
The test is carried out on five specimens
In case of doubt, additional test with proof voltage
reduced by 25V, the number of drops increased to
100
10.2
P
N/A
Report
The report states if the PTI value was based on a
test using 100 drops with a test voltage of (PTI-25)
V
O
P
N/A
ANNEX O (INFORMATIVE)
SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30
Description of tests for determination of resistance
to heat and fire
TRF No. IEC60335_2_80E
P
Page 67 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
P
ANNEX P (INFORMATIVE)
GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES
USED IN WARM DAMP EQUABLE CLIMATES
Verdict
Modifications applicable for class 0 and 01 appliances having a rated voltage
exceeding 150V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE
N/A
Modifications may also be applied to class 1 appliances having a rated voltage
exceeding 150V, intended to be used in countries having a warm damp equable
climate and that are marked WdaE, if liable to be connected to a supply mains that
excludes the protective earthing conductor
N/A
5.7
The ambient temperature for the tests of clauses 11
and 13 is 40 +3/0 C
N/A
7.1
The appliance marked with the letters WDaE
N/A
7.12
The instructions state that the appliance is to be
supplied through a residual current device (RCD)
having a rated residual operating current not
exceeding 30 mA
N/A
The instructions state that the appliance is
considered to be suitable for use in countries
having a warm damp equable climate, but may also
be used in other countries
N/A
11.8
The values of Table 3 are reduced by 15 K
N/A
13.2
The leakage current for class I appliances not
exceeding 0,5 mA
N/A
15.3
The value of t is 37 C
N/A
16.2
The leakage current for class I appliances not
exceeding 0,5 mA (mA):
N/A
19.13
The leakage current test of 16.2 is applied in
addition to the electric strength test of 16.3
N/A
Q
ANNEX Q (INFORMATIVE)
SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS
Description of tests for appliances incorporating electronic circuits
R
R.1
P
ANNEX R (NORMATIVE)
SOFTWARE EVALUATION
Programmable electronic circuits requiring software
incorporating measures to control the fault/error
conditions specified in table R.1 or R.2 validated in
accordance with the requirements of this annex
N/A
Programmable electronic circuits using software
N/A
TRF No. IEC60335_2_80E
Page 68 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Programmable electronic circuits requiring software
incorporating measures to control the fault/error
conditions specified in table R.1 or R.2 constructed
so that the software does not impair compliance
with the requirements of this standard
N/A
Requirements for the architecture
N/A
Programmable electronic circuits requiring software
incorporating measures to control the fault/error
conditions specified in table R.1 or R.2 use
measures to control and avoid software-related
faults/errors in safety-related data and safetyrelated segments of the software
N/A
Programmable electronic circuits requiring software incorporating measures to
control the fault/error conditions specified in table R.2 have one of the following
structures:
N/A
- single channel with periodic self-test and
monitoring
N/A
- dual channel (homogenous) with comparison
N/A
- dual channel (diverse) with comparison
N/A
Programmable electronic circuits requiring software incorporating measures to
control the fault/error conditions specified in table R.1 have one of the following
structures:
N/A
- single channel with functional test
N/A
- single channel with periodic self-test
N/A
- dual channel without comparison
N/A
R.2.2
Measures to control faults/errors
N/A
R.2.2.1
When redundant memory with comparison is
provided on two areas of the same component, the
data in one area is stored in a different format from
that in the other area
N/A
R.2.2.2
Programmable electronic circuits with functions
requiring software incorporating measures to
control the fault/error conditions specified in table
R.2 and that use dual channel structures with
comparison, have additional fault/error detection
means for any fault/errors not detected by the
comparison
N/A
R.2.2.3
For programmable electronic circuits with functions
requiring software incorporating measures to
control the fault/error conditions specified in table
R.1 or R.2, means are provided for the recognition
and control of errors in transmissions to external
safety-related data paths
N/A
R.2
R.2.1.1
TRF No. IEC60335_2_80E
Page 69 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
R.2.2.4
For programmable electronic circuits with functions
requiring software incorporating measures to
control the fault/error conditions specified in table
R.1 or R.2, the programmable electronic circuits
incorporate measures to address the fault/errors in
safety-related segments and data indicated in table
R.1 and R.2 as appropriate
N/A
R.2.2.5
For programmable electronic circuits with functions
requiring software incorporating measures to
control the fault/error conditions specified in table
R.1 or R.2, detection of a fault/error occur before
compliance with clause 19 is impaired
N/A
R.2.2.6
The software is referenced to relevant parts of the
operating sequence and the associated hardware
functions
N/A
R.2.2.7
Labels used for memory locations are unique
N/A
R.2.2.8
The software is protected from user alteration of
safety-related segments and data
N/A
R.2.2.9
Software and safety-related hardware under its
control is initialized and terminates before
compliance with clause 19 is impaired
N/A
R.3
Measures to avoid errors
N/A
R.3.1
General
Verdict
For programmable electronic circuits with functions requiring software incorporating
measures to control the fault/error conditions specified in table R.1 or R.2, the
following measures to avoid systematic fault in the software are applied
N/A
Software that incorporates measures used to
control the fault/error conditions specified in table
R.2 is inherently acceptable for software required to
control the fault/error conditions specified in table
R.1
N/A
R.3.2
Specification
R.3.2.1
Software safety requirements:
The specification of the software safety
requirements includes the descriptions listed
R.3.2.2
Result - Remark
Software architecture
TRF No. IEC60335_2_80E
Software Id:
N/A
N/A
Page 70 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
R.3.2.2.1
The specification of the software architecture
Document ref. No:
includes the aspects listed
- techniques and measures to control software
faults/errors (refer to R.2.2);
- interactions between hardware and software;
- partitioning into modules and their allocation to the
specified safety functions;
- hierarchy and call structure of the modules
(control flow);
- interrupt handling;
- data flow and restrictions on data access;
- architecture and storage of data;
- time-based dependencies of sequences and data
N/A
R.3.2.2.2
The architecture specification is validated against
the specification of the software safety
requirements by static analysis
N/A
R.3.2.3
Module design and coding
R.3.2.3.1
Based on the architecture design, software is
suitably refined into modules
N/A
Software module design and coding is implemented
in a way that is traceable to the software
architecture and requirements
N/A
R.3.2.3.2
Software code is structured
N/A
R.3.2.3.3
Coded software is validated against the module
specification by static analysis
N/A
The module specification is validated against the
architecture specification by static analysis
N/A
R.3.3.3
Result - Remark
Software validation
The software is validated with reference to the
requirements of the software safety requirements
specification
N/A
Compliance is checked by simulation of:
N/A
- input signals present during normal operation
N/A
- anticipated occurrences
N/A
- undesired conditions requiring system action
N/A
TABLE R.1 – GENERAL FAULT/ERROR CONDITIONS
Component
1)
Verdict
Fault/error
TRF No. IEC60335_2_80E
Acceptable measures
2) 3)
N/A
Definitions
Document Document
reference reference
for applied for applied
measure
test
Verdict
Page 71 of 101
Report No. 247910
IEC 60335-2-80
Clause
1 CPU
1.1
Registers
Requirement - Test
Stuck at
Result - Remark
Functional test, or
periodic self-test using either:
- static memory test, or
- word protection with
single bit redundancy
H.2.16.5
H.2.16.6
H.2.19.6
H.2.19.8.2
Functional test, or
Periodic self-test, or
Independent time-slot
monitoring, or
Logical monitoring of the
programme sequence
H.2.16.5
H.2.16.6
H.2.18.10.
4
1.2 VOID
1.3
Stuck at
Programme
counter
H.2.18.10.
2
2
Interrupt
handling
and
execution
No interrupt
or too
frequent
interrupt
Functional test, or
time-slot monitoring
H.2.16.5
H.2.18.10.
4
3
Clock
Wrong
frequency
(for quartz
synchronize
d clock:
harmonics/
subharmonics
only)
Frequency monitoring, or
time slot monitoring
H.2.18.10.
1
H.2.18.10.
4
All single bit
faults
Periodic modified checksum, or H.2.19.3.1
multiple checksum, or
H.2.19.3.2
word protection with single bit
H.2.19.8.2
redundancy
DC fault
Periodic static memory test, or
word protection with single bit
redundancy
H.2.19.6
H.2.19.8.2
4.3
Stuck at
Addressing
(relevant to
variable and
invariable
memory)
Word protection with single bit
redundancy including the
address
H.2.19.8.2
4. Memory
4.1
Invariable
memory
4.2
Variable
memory
TRF No. IEC60335_2_80E
Verdict
Page 72 of 101
Report No. 247910
IEC 60335-2-80
Clause
5
Internal
data path
Requirement - Test
Result - Remark
Stuck at
DC fault
Word protection with single bit
H.2.19.8.2
redundancy
Comparison of redundant CPUs
by either:
- reciprocal comparison H.2.18.15
- independent hardware H.2.18.3
comparator
Wrong
address
Word protection with single bit
redundancy including the
address
H.2.19.8.2
Word protection with multi-bit
redundancy, or
CRC – single work, or
Transfer redundancy, or
Protocol test
H.2.19.8.1
5.1 VOID
5.2
Addressing
6
Hamming
External
distance 3
communicat
ion
H.2.19.4.1
H.2.18.2.2
H.2.18.14
6.1 VOID
6.2 VOID
6.3
Timing
Wrong point Time-slot monitoring, or
in time
scheduled transmission
Time-slot and logical
monitoring, or
Comparison of redundant
communication channels by
either:
- reciprocal comparison
- independent hardware
comparator
Wrong
Logical monitoring, or
sequence
time-slot monitoring, or
Scheduled transmission
(same options as for wrong
point in time)
TRF No. IEC60335_2_80E
H.2.18.10.
4
H.2.18.18
H.2.18.10.
3
H.2.18.15
H.2.18.3
H.2.18.10.
2
H.2.18.10.
4
H.2.18.18
Verdict
Page 73 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
7
Fault
Input/output conditions
periphery
specified in
19.11.2
Result - Remark
Plausibility check
Comparison of redundant
communication channels by
either:
- reciprocal comparison
- independent hardware
comparator
H.2.18.13
Verdict
H.2.18.15
H.2.18.3
7.1 VOID
7.2
Analog I/O
7.2.1
A/D and
D/Aconverter
Fault
conditions
specified in
19.11.2
Plausibility check
H.2.18.13
7.2.2
Analog
multiplexer
Wrong
addressing
Plausibility check
H.2.18.13
8 VOID
9
Custom
chips 4) e.g.
ASIC, GAL,
Gate array
Any output
Periodic self-test
outside the
static and
dynamic
functional
specification
H.2.16.6
NOTE A Stuck-at fault model denotes a fault model representing an open circuit or a non-varying signal
level. A DC fault model denotes a stuck-at fault model incorporating short circuit between signal lines.
1)
For fault/error assessment, some components are divided into their sub-functions.
For each sub-function in the table, the Table R.2 measure will cover the software fault/error.
3)
Where more than one measure is given for a sub-function, these are alternatives.
4)
To be divided as necessary by the manufacturer into sub-functions.
2)
TRF No. IEC60335_2_80E
Page 74 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
10.1
TABLE: Power input deviation (at ambient 40 C)
Input deviation of/at:
Result - Remark
Verdict
P
P rated (W)
P measured (W)
dP
(W, %)
Required dP
(W, %)
Remark
230V(KN-2905)
5
1,8
-64%
+20%
P
230V(KN-2903)
4
1,3
-67,5%
+20%
P
230V(KN-2712)
24
23,6
-1,7%
+20%
P
230V(KN-2926)
30
31,8
+6%
+20%
P
230V(KN-2918HR)
30
33,1
+10,3%
+20%
P
230V(KN-2912)
24
19,2
-20%
+20%
P
230V(KN-2916)
24
23,9
-0,4%
+20%
P
230V(KN-2914H)
24
23,4
-2,5%
+20%
P
230V(KN-2918H)
30
28,5
-5%
+20%
P
230V(KN-2914HR)
24
23,2
-3,3%
+20%
P
230V(KN-2926HR)
30
29,3
-2,3%
+20%
P
Supplementary information:
10.2
N/A
TABLE: Current deviation
Current deviation of/at:
I rated (A)
I measured (A)
dI
(A, %)
Required dI
(A, %)
Remark
Supplementary information:
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2905 / KN-2903 worked on AC and charge mode)
Test voltage (V) .................................................... :
254,4V
Ambient ( C) ......................................................... :
40oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2905 / KN-2903
Max.temperature rise limit,
dT (K)
Pins of appliance inlet
10 / 11
45-15=30
Motor case
9 / 18
85-15=70
Holder of fan motor
8 / 15
For Cl.30
TRF No. IEC60335_2_80E
Page 75 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Main PCB
20 / 21
120-15=105
Internal wire
11 / 12
80-15=65
Control board
3/4
60-15=45
Battery
11 / 4
For reference
8/-
For Cl.30
Enclosure inside
12 / 5
For Cl.30
Enclosure outside
12 / 5
65-15=50
Test corner
2/6
65-15=50
Ambient of switch for motor
12 / 12
For Cl.30
Ambient of switch for lighting
10 / 9
For Cl.30
Heat shrinkable tube
4/3
125-15=110
LED lamp cover
6 / 12
60-15=45
Holder for wire connector
Supplementary information:
11.8
N/A
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
Ambient, t1 ( C) .................................................... :
Ambient, t2 ( C) .................................................... :
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Supplementary information:
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2905 / KN-2903 worked on fully charged battery)
Test voltage (V) .................................................... :
Battery operated
Ambient ( C) ......................................................... :
40oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2905 / KN-2903
Max.temperature rise limit,
dT (K)
Pins of appliance inlet
2/6
45-15=30
Motor case
4 / 16
85-15=70
Holder of fan motor
4 / 12
For Cl.30
Main PCB
3/6
120-15=105
TRF No. IEC60335_2_80E
Page 76 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Internal wire
3/8
80-15=65
Control board
2/8
60-15=45
Battery
5/6
For reference
Holder for wire connector
4/-
For Cl.30
Enclosure inside
3/6
For Cl.30
Enclosure outside
4/5
65-15=50
Test corner
2/5
65-15=50
Ambient of switch for motor
3/5
For Cl.30
Ambient of switch for lighting
3/4
For Cl.30
Heat shrinkable tube
3/3
125-15=110
LED lamp cover
2 / 11
60-15=45
Supplementary information:
11.8
N/A
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
Ambient, t1 ( C) .................................................... :
Ambient, t2 ( C) .................................................... :
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Supplementary information:
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2905 / KN-2903 when the battery is charging only)
Test voltage (V) .................................................... :
254,4V
Ambient ( C) ......................................................... :
25oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2905 / KN-2903
Max.temperature rise limit,
dT (K)
8 / 11
45-15=30
Motor case
2/3
85-15=70
Holder of fan motor
2/3
For Cl.30
Main PCB
19 / 23
120-15=105
Internal wire
8 / 13
80-15=65
Pins of appliance inlet
TRF No. IEC60335_2_80E
Page 77 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Control board
2/6
60-15=45
Battery
5/8
For reference
Holder for wire connector
5/-
For Cl.30
Enclosure inside
4/6
For Cl.30
Enclosure outside
4/4
65-15=50
Test corner
3/3
65-15=50
Ambient of switch for motor
10 / 14
For Cl.30
Ambient of switch for lighting
9 / 11
For Cl.30
Heat shrinkable tube
2/2
125-15=110
LED lamp cover
3/2
60-15=45
Supplementary information:
11.8
N/A
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
Ambient, t1 ( C) .................................................... :
Ambient, t2 ( C) .................................................... :
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Supplementary information:
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2712 / KN-2926 / KN-2912 / KN-2916 worked on AC and charge mode)
Test voltage (V) .................................................... :
254,4V
Ambient ( C) ......................................................... :
40oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2712 / KN-2926 / KN-2912 /
KN-2916
Max.temperature rise limit,
dT (K)
Pri-winding of transformer Class130 (B)
60 / 58 / 50 / 57
85-15=70
Sec-winding of transformer Class130
(B)
65 / 59 / 57 / 59
Winding of motor Class130 (B)
23 / 65 / 20 / 44
85-15=70
Holder of fan motor
18 / 57 / 16 / 39
For Cl.30
TRF No. IEC60335_2_80E
85-15=70
Page 78 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Main PCB
37 / 73 / 82 / 70
120-15=105
Internal wire
12 / 32 / 20 / 27
80-15=65
Control board
5 / 6 / 3 / 11
60-15=45
Battery
6 / 7 / 18 / 18
For reference
6/4/7/6
65-15=50
Enclosure inside
20 / 25 / 14 / 16
For Cl.30
Enclosure outside
11 / 22 / 10 / 13
65-15=50
Ambient of switch for motor
10 / 19 / 18 / 17
For Cl.30
Ambient of switch for lighting
11 / 18 / 15 / 16
For Cl.30
Ambient of main selection switch
11 / 18 / 14 / 15
For Cl.30
Heat shrinkable tube
17 / 22 / 12 / 14
125-15=110
Pins for appliance inlet
20 / 15 / 15 / 21
45-15=30
8 / 7 / 7 / 12
60-15=45
Test corner
LED lamp cover
Supplementary information:
11.8
P
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
254,4
Ambient, t1 ( C) .................................................... :
40
Ambient, t2 ( C) .................................................... :
40
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Pri-winding of transformer(Class
B) (model: EI48)
124,5
155,3
68
80
Class 130
Sec-winding of transformer(Class
B) (model: EI48)
0,80
1,00
69
80
Class 130
Pri-winding of transformer(Class
B) (model: EI57, 12,5V)
164,2
201,6
63
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 12,5V)
2,30
2,84
65
80
Class 130
Pri-winding of transformer(Class
B) (model: EI57, 7,5V)
130,0
160,5
65
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 7,5V)
1,00
1,24
66
80
Class 130
Supplementary information:
TRF No. IEC60335_2_80E
Page 79 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2712 / KN-2926 / KN-2912 / KN-2916 worked on fully charged battery)
Test voltage (V) .................................................... :
Battery operated
Ambient ( C) ......................................................... :
40oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2712 / KN-2926 / KN-2912 /
KN-2916
Max.temperature rise limit,
dT (K)
Pri-winding of transformer Class130 (B)
1/1/2/6
85-15=70
Sec-winding of transformer Class130
(B)
1/2/2/6
85-15=70
Winding of motor Class130 (B)
14 / 56 / 15 / 26
85-15=70
Holder of fan motor
12 / 48 / 11 / 23
For Cl.30
Main PCB
9 / 36 / 17 / 20
120-15=105
Internal wire
7 / 31 / 9 / 17
80-15=65
3/4/4/6
60-15=45
6 / 7 / 11 / 6
For reference
Test corner
6/3/2/7
65-15=50
Enclosure inside
1/3/4/6
For Cl.30
Enclosure outside
9/6/4/7
65-15=50
Ambient of switch for motor
2 / 9 / 7 / 10
For Cl.30
Ambient of switch for lighting
3/9/5/6
For Cl.30
Ambient of main selection switch
3/7/4/4
For Cl.30
11 / 18 / 10 / 12
125-15=110
Pins for appliance inlet
1/1/2/6
45-15=30
LED lamp cover
8/6/4/8
60-15=45
Control board
Battery
Heat shrinkable tube
Supplementary information:
11.8
N/A
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
Ambient, t1 ( C) .................................................... :
Ambient, t2 ( C) .................................................... :
Temperature rise of winding
TRF No. IEC60335_2_80E
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Page 80 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Supplementary information: The appliance is powered by battery ,transformer not worked
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2712 / KN-2926 / KN-2912 / KN-2916 when the battery is charging only)
Test voltage (V) .................................................... :
254,4V
Ambient ( C) ......................................................... :
25oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2712 / KN-2926 / KN-2912 /
KN-2916
Max.temperature rise limit,
dT (K)
Pri-winding of transformer Class130 (B)
56 / 48 / 40 / 37
85-15=70
Sec-winding of transformer Class130
(B)
50 / 45 / 40 / 38
85-15=70
Winding of motor Class130 (B)
4/1/4/2
85-15=70
Holder of fan motor
4/2/4/2
For Cl.30
Main PCB
33 / 68 / 80 / 40
120-15=105
Internal wire
11 / 18 / 21 / 15
80-15=65
6/4/1/6
60-15=45
Battery
8 / 12 / 15 / 6
For reference
Test corner
11 / 1 / 8 / 3
65-15=50
Enclosure inside
21 / 15 / 15 / 12
For Cl.30
Enclosure outside
13 / 11 / 12 / 7
65-15=50
Ambient of switch for motor
10 / 30 / 18 / 17
For Cl.30
Ambient of switch for lighting
11 / 26 / 14 / 16
For Cl.30
Ambient of main selection switch
11 / 25 / 16 / 16
For Cl.30
2/5/3/3
125-15=110
23 / 12 / 16 / 16
45-15=30
3/3/2/2
60-15=45
Control board
Heat shrinkable tube
Pins for appliance inlet
LED lamp cover
Supplementary information:
11.8
P
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
254,4
Ambient, t1 ( C) .................................................... :
25
TRF No. IEC60335_2_80E
Page 81 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
25
Ambient, t2 ( C) .................................................... :
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Pri-winding of transformer(Class
B) (model: EI48)
124,5
154,2
62
80
Class 130
Sec-winding of transformer(Class
B) (model: EI48)
0,800
0,980
58
80
Class 130
Pri-winding of transformer(Class
B) (model: EI57, 12,5V)
164,0
200,5
58
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 12,5V)
2,30
2,79
56
80
Class 130
Pri-winding of transformer(Class
B) (model: EI57, 7,5V)
130,0
152,5
45
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 7,5V)
1,00
1,18
47
80
Class 130
Supplementary information:
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2918HR / KN-2926HR / KN-2914HR / KN-2918H / KN-2914H worked on
AC and charge mode)
Test voltage (V) .................................................... :
254,4V
Ambient ( C) ......................................................... :
40oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2918H / KN-2926HR / KN2914HR / KN-2918HR / KN-2914H
Max.temperature rise limit,
dT (K)
Pri-winding of transformer Class130 (B)
57 / 66 / 49 / 62 / 51
85-15=70
Sec-winding of transformer Class130
(B)
53 / 66 / 45 / 61 / 49
Winding of motor Class130 (B)
34 / 57 / 39 / 33 / 37
85-15=70
Holder of fan motor
30 / 48 / 38 / 26 / 36
For Cl.30
Main PCB
45 / 55 / 49 / 45 / 63
120-15=105
Internal wire
26 / 24 / 24 / 25 / 30
80-15=65
Control board
9 / 5 / 8 / 9 / 10
60-15=45
Ambient of switch for motor
30 / - / - / - / 26
For Cl.30
Ambient of switch for lighting
28 / - / - / - / 25
For Cl.30
Ambient of main selection switch
25 / - / - / - / 24
For Cl.30
18 / 9 / 12 / 23 / 14
For reference
Battery
TRF No. IEC60335_2_80E
85-15=70
Page 82 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Test corner
Verdict
6 / 3 / 6 / 11 / 8
65-15=50
Enclosure inside
17 / 20 / 26 / 20 / 25
For Cl.30
Enclosure outside
14 / 14 / 23 / 15 / 22
60-15=45
8 / 12 / 10 / 7 / 11
For Cl.30
Heat shrinkable tube
25 / 32 / 28 / 20 / 26
125-15=110
Pins for appliance inlet
20 / 19 / 19 / 16 / 19
45-15=30
LED lamp cover
17 / 5 / 10 / 12 / 11
60-15=45
Holder for wire connector
Supplementary information:
11.8
P
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
254,4
Ambient, t1 ( C) .................................................... :
40
Ambient, t2 ( C) .................................................... :
40
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Pri-winding of transformer(Class
B) (model: EI57, 12,5V)
164,0
205,3
70
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 12,5V)
2,30
2,88
70
80
Class 130
Pri-winding of transformer(Class
B) (model: EI57, 7,5V)
130,0
156,5
56
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 7,5V)
1,00
1,19
53
80
Class 130
Supplementary information:
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2918HR / KN-2926HR / KN-2914HR / KN-2918H / KN-2914H worked on
fully charged battery)
Test voltage (V) .................................................... :
Battery operated
Ambient ( C) ......................................................... :
40oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
KN-2918H / KN-2926HR / KN2914HR / KN-2918HR / KN-2914H
Max.temperature rise limit,
dT (K)
Pri-winding of transformer Class130 (B)
6/5/8/5/6
85-15=70
Sec-winding of transformer Class130
(B)
6/4/8/5/6
TRF No. IEC60335_2_80E
85-15=70
Page 83 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Winding of motor Class130 (B)
26 / 37 / 25 / 26 / 25
85-15=70
Holder of fan motor
22 / 32 / 24 / 21 / 24
For Cl.30
Main PCB
30 / 15 / 20 / 15 / 16
120-15=105
Internal wire
10 / 10 / 15 / 6 / 11
80-15=65
Control board
6/4/7/5/6
60-15=45
Ambient of switch for motor
20 / - / - / - / 9
For Cl.30
Ambient of switch for lighting
17 / - / - / - / 10
For Cl.30
Ambient of main selection switch
14 / - / - / - / 10
For Cl.30
Battery
7 / 5 / 10 / 7 / 6
For reference
2/5/5/4/7
65-15=50
Enclosure inside
6 / 12 / 14 / 15 / 11
For Cl.30
Enclosure outside
5 / 7 / 11 / 14 / 10
60-15=45
5 / 6 / 10 / 4 / 4
For Cl.30
11 / 12 / 10 / 8 / 8
125-15=110
Pins for appliance inlet
5/4/8/5/6
45-15=30
LED lamp cover
15 / 5 / 9 / 8 / 7
60-15=45
Test corner
Holder for wire connector
Heat shrinkable tube
Supplementary information:
11.8
N/A
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
Ambient, t1 ( C) .................................................... :
Ambient, t2 ( C) .................................................... :
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Supplementary information: The appliance is powered by battery ,transformer not worked
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2918HR / KN-2926HR / KN-2914HR / KN-2918H / KN-2914H when the
battery is charging only)
Test voltage (V) .................................................... :
254,4V
Ambient ( C) ......................................................... :
25oC
TRF No. IEC60335_2_80E
P
Page 84 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Thermocouple locations
Verdict
Max. temperature rise measured,
dT (K)
KN-2918H / KN-2926HR / KN2914HR / KN-2918HR / KN-2914H
Max.temperature rise limit,
dT (K)
Pri-winding of transformer Class130 (B)
36 / 36 / 32 / 44 / 33
85-15=70
Sec-winding of transformer Class130
(B)
36 / 38 / 29 / 40 / 29
85-15=70
Winding of motor Class130 (B)
1/3/3/2/1
85-15=70
Holder of fan motor
1/3/1/1/1
For Cl.30
Main PCB
35 / 28 / 28 / 34 / 30
120-15=105
Internal wire
16 / 36 / 21 / 26 / 27
80-15=65
Control board
4/4/4/8/6
60-15=45
Ambient of switch for motor
25 / - / - / - / 15
For Cl.30
Ambient of switch for lighting
22 / - / - / - / 15
For Cl.30
Ambient of main selection switch
18 / - / - / - / 14
For Cl.30
Battery
11 / 6 / 5 / 16 / 6
For reference
Test corner
4/3/4/3/2
65-15=50
Enclosure inside
6 / 6 / 5 / 13 / 7
For Cl.30
Enclosure outside
6/3/3/9/6
60-15=45
Holder for wire connector
1/2/1/1/1
For Cl.30
Heat shrinkable tube
1/1/1/1/1
125-15=110
10 / 11 / 10 / 16 / 11
45-15=30
2/1/1/4/2
60-15=45
Pins for appliance inlet
LED lamp cover
Supplementary information:
11.8
P
TABLE: Heating test, resistance method
Test voltage (V) .................................................... :
254,4
Ambient, t1 ( C) .................................................... :
25
Ambient, t2 ( C) .................................................... :
25
Temperature rise of winding
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
Pri-winding of transformer(Class
B) (model: EI57, 12,5V)
164,0
194,9
49
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 12,5V)
2,30
2,70
46
80
Class 130
TRF No. IEC60335_2_80E
Page 85 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Pri-winding of transformer(Class
B) (model: EI57, 7,5V)
130,0
148,6
38
80
Class 130
Sec-winding of transformer(Class
B) (model: EI57, 7,5V)
1,00
1,14
37
80
Class 130
Supplementary information:
11.8
TABLE: Heating test, thermocouple measurements, under tropical climate (for
model KN-2926HR when worked on external DC source and charge mode)
Test voltage (V) .................................................... :
DC 1 V
Ambient ( C) ......................................................... :
40oC
Thermocouple locations
P
Max. temperature rise measured,
dT (K)
Max.temperature rise limit,
dT (K)
Winding of motor Class130 (B)
30
85-15=70
Holder of fan motor
29
For Cl.30
Main PCB
28
120-15=105
Internal wire
14
80-15=65
Control board
6
60-15=45
Battery
5
For reference
Test corner
6
65-15=50
Enclosure
9
60-15=45
Holder for wire connector
11
For Cl.30
Heat shrinkable tube
12
125-15=110
Pins for DC inlet
17
45-15=30
LED lamp cover
6
60-15=45
Supplementary information:
13.2
P
TABLE: Leakage current (at ambient 40 C)
Heating appliances: 1.15 x rated input (W) ....... :
254,4V
Motor-operated and combined appliances:
1.06 x rated voltage (V) .....................................:
Leakage current between
Live parts and accessible parts over reinforced insulation
Supplementary information:
TRF No. IEC60335_2_80E
I (mA)
Max. allowed I (mA)
0,005 peak
0,35 peak
Page 86 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
13.3
TABLE: Electric strength (at ambient 40 C)
Test voltage applied between:
Live parts and accessible parts over reinforced insulation
Verdict
P
Voltage (V)
Breakdown
(Yes/No)
3000
No
Supplementary information:
14
N/A
TABLE: Transient overvoltages
Clearance between:
Cl (mm)
Required Cl Rated impulse
(mm)
voltage (V)
Impulse test
voltage (V)
Flashover
(Yes/No)
Supplementary information:
16.2
P
TABLE: Leakage current
254,4V
Single phase appliances: 1.06 x rated voltage (V)
..........................................................................:
Three phase appliances 1.06 x rated voltage
divided by 3 (V) ...............................................:
Leakage current between
I (mA)
Max. allowed I (mA)
Live parts and accessible parts over reinforced insulation
0,006
0,25
Supplementary information:
16.3
P
TABLE: Electric strength
Test voltage applied between:
Live parts and accessible parts over reinforced insulation
Voltage (V)
Breakdown
(Yes/No)
3000
No
Supplementary information:
17
P
TABLE: Overload protection, thermocouple measurements
Temperature rise of part/at:
TRF No. IEC60335_2_80E
dT (K)
Max. dT (K)
Page 87 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Primary winding of transformer EI57, 7,5V Class130 (B)
81
200
Secondary winding of transformer EI57, 7,5V Class130 (B)
37
200
Primary winding of transformer EI57, 12,5V Class130 (B)
64
200
Secondary winding of transformer EI57, 12,5V Class130 (B)
80
200
Primary winding of transformer EI48, 7,5V Class130 (B)
76
200
Secondary winding of transformer EI48, 7,5V Class130 (B)
81
200
SELV wire
55
95
Supplementary information: Thermal link operated, no hazard
17
N/A
TABLE: Overload protection, resistance method
Test voltage (V) .................................................... :
Ambient, t1 ( C) .................................................... :
Ambient, t2 ( C) .................................................... :
Temperature of winding
R1 ( )
R2 ( )
dT (K)
T ( C)
Max. T (°C)
Supplementary information: Thermal link operated, no hazard
19
Abnormal operation conditions
Operational characteristics
YES/NO
Are there electronic circuits to
control the appliance operation?
Yes
Are there “off” or “stand-by”
position?
Yes
The unintended operation of the
appliance results in dangerous
malfunction?
No
Operational conditions
Moving parts are guarded and not accessible
Sub-clause
Operating
conditions
description
Test
results
description
PEC
description
19.2
N/A
N/A
N/A
TRF No. IEC60335_2_80E
P
EMP
19.11.4
N/A
Software
type
required
N/A
19.11.3
PEC
N/A
Final
result
N/A
3856-117D
Winding of fan motor
Class130 (B) SH-555STP3856-117D
Page 90 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
24.1
TABLE: Components information
Object / part No. Manufacturer/
trademark
Plug
Alt.
Alt.
UK Plug
Alt.
Alt.
Supply cord
Dongguan
Changqi
Electronics Co.,
Ltd
Zhongshan
Xiaolan Qiangli
Electric Factory
Co., Ltd.
Interchangeable
Result - Remark
Verdict
P
Type / model
Technical data
Standard
Mark(s) of
conformity1)
CQ-013
2,5A, 250V~
VDE 0620-1
IEC 60884
VDE
40015914
QL-VA1
2,5A, 250V~
VDE 0620-1
IEC 60884
VDE
40013545
Interchangeabl 2,5A, 250V~
e
CWL668
13A, 250V~
VDE 0620-1
VDE
BS1363-1
BSI
KM82901
BS1363-1
ASTA
LICENCE
NO. 735
BSI
Shenzhen Bao’an
Xixiang
Changxiao
Electric
Manufacture
Factory
Zhong Shan
QL-340
13A, 250V~
Qiang Li Electrical
Factory Co., Ltd.
Interchangeable
Interchangeabl 13A, 250V~
e
Dongguan
H03VVH2-F
2x0,75mm2
Changqi
H05VVH2-F
Electronics Co.,
Ltd
BS1363-1
DIN VDE 0281-5
HD 21.5 S3
60227 IEC 52/53
VDE
40011173
Alt.
Zhongshan
Xiaolan Qiangli
Electric Factory
Co., Ltd.
H03VVH2-F
H05VVH2-F
2x0,75mm2
DIN VDE 0281-5
HD 21.5 S3
60227 IEC 52/53
VDE
109832
Alt.
Interchangeable
H03VVH2-F
H05VVH2-F
2x0,75mm2
DIN VDE 0281-5
HD 21.5 S3
60227 IEC 52/53
VDE
DC inlet
KEXIN Electronic
factory
DC-0053
DC 30V, 0,3A
IEC 60335-2-80
Tested in
the
appliance
Appliance inlet
ZHE JIANG BEI
ER JIA
ELECTRONIC
CO.LTD
Dongguan
Changqi
Electronics Co.,
Ltd
ST-A03-002
ST-A03-005
250V 2,5A
IEC/EN 60320-1
VDE
40014833
CQ-017
250V 2,5A
IEC/EN 60320-1
VDE
40016842
Appliance
connector
TRF No. IEC60335_2_80E
Page 91 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Alt.
Interchangeable
Interchangeabl 250V 2,5A
e
IEC/EN 60320-1
VDE
Fan motor for
KN-2918HR
KN-2918H only
Rock
Motor(shenzhen)
Co., Ltd.
KRS-775STP- DC 12V 1,7A
31120Class 130 (B)
144.2FD
IEC 60335-2-80
Tested in
the
appliance
Fan motor for
KN-2916HR
KN-2914HR
KN-2916H
KN-2914H
KN-2916
KN-2914
Alt.
Rock
Motor(shenzhen)
Co., Ltd.
KRS-560STP- DC 6V 1,75A
33120-127.5D Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Dongguan BestFit Electric Co.,
Ltd.
SH-560STP- DC 6V 1,58A
33120-127.5D Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Fan motor for
KN-2926
KN-2924
KN-2926H
KN-2926HR
Fan motor for
KN-2912
Rock
Motor(shenzhen)
Co., Ltd.
KRS-560STP- DC 12V 1,3A
27110-127.5D Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Rock
Motor(shenzhen)
Co., Ltd.
KRS-550STP- DC 6V 1,2A
35112-123D
Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Alt.
Dongguan BestFit Electric Co.,
Ltd.
SH-550STP35112-123D
DC 6V 1,83A
Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Fan motor for
KN-2712
Rock
Motor(shenzhen)
Co., Ltd.
KRS-555STP- DC 6V 1,3A
3856-117D
Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Alt.
Dongguan BestFit Electric Co.,
Ltd.
SH-555STP3856-117D
DC 6V 1,83A
Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Fan motor for
KN-2905
Rock
Motor(shenzhen)
Co., Ltd.
KN-2905M
DC 4,2V 0,34A
Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Fan motor for
KN-2903
Rock
Motor(shenzhen)
Co., Ltd.
KN-2903M
DC 4,2V 0,22A
Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
Transformer for
KN-2914HR
KN-2916HR
KN-2914
KN-2916
KN-2914H
KN-2916H only
Kennede
Electronics MFG.
Co., Ltd.
EI57
I/P: 220-240V~
50/60Hz
O/P:
7,5V~ 2,5A
Class 130 (B)
IEC 60335-2-80
Tested in
the
appliance
TRF No. IEC60335_2_80E
Page 92 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
-Bobbin
Chang Chun
Plastics Co Ltd
T375J
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E59481
-Alt.
Chang Chun
Plastics Co Ltd
4115 (a)
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E59481
-Alt.
E I DUPONT DE
NEMOURS & CO
INC
FR50(+)(f1)
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E41938
-Thermal link
Aupo Electronics
Ltd.
A4
2A, 250V~,
130oC
IEC/EN 60691
Tested in
the
appliance/
VDE
40008720
Transformer for
KN-2712
KN-2912
only
-Bobbin
Kennede
Electronics MFG.
Co., Ltd.
EI48
IEC 60335-2-80
Test in the
with
appliance
Chang Chun
Plastics Co Ltd
T375J
I/P: 220-240V~
50/60Hz
O/P:
7,5V~ 1,9A
Class 130 (B)
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E59481
-Alt.
Chang Chun
Plastics Co Ltd
4115 (a)
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E59481
-Alt.
E I DUPONT DE
NEMOURS & CO
INC
FR50(+)(f1)
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E41938
-Thermal link
Aupo Electronics
Ltd.
A4
2A, 250V~,
130oC
IEC/EN 60691
Tested in
the
appliance/
VDE
40008720
Transformer for
KN-2924
KN-2926
KN-2918H
KN-2926H
KN-2926HR
KN-2918HR
only
Kennede
Electronics MFG.
Co., Ltd.
EI57
I/P:220-240V~
50/60Hz
O/P:12,5V~ 1,5A
Class 130 (B)
IEC 60335-2-80
Test with
appliance
TRF No. IEC60335_2_80E
Tf
Tf
Page 93 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
-Bobbin
Chang Chun
Plastics Co Ltd
T375J
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E59481
-Alt.
Chang Chun
Plastics Co Ltd
4115 (a)
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E59481
-Alt.
E I DUPONT DE
NEMOURS & CO
INC
FR50(+)(f1)
V-0
IEC 60335-2-80
Tested in
the
appliance/
UL E41938
-Thermal link
Aupo Electronics
Ltd.
A4
2A, 250V~,
130oC
IEC/EN 60691
Tested in
the
appliance/
VDE
40008720
Internal wire
Jiang Men Jia
Chuan Electric &
Cable Co LTD
1007
300V~, 18-26AWG IEC 60335-2-80
T80
Tested in
the
appliance
UL E315723
Alt.
ZHONG SHAN
YONG ROI
ELECTRIC
FACTORY
CO LTD
1007
300V~, 18-26AWG IEC 60335-2-80
T80
Tested in
the
appliance
UL E204893
Alt.
Jiang Men Jia
Chuan Electric &
Cable Co LTD
1015
600V~, 18-26AWG IEC 60335-2-80
T105
Tested in
the
appliance
UL E315723
Alt.
ZHONG SHAN
YONG ROI
ELECTRIC
FACTORY
CO LTD
1015
600V~, 18-26AWG IEC 60335-2-80
T105
Tested in
the
appliance
UL E204893
Motor lead wire
Jiang Men Jia
Chuan Electric &
Cable Co LTD
1015 / 1007 /
2464
600V / 300V~, 1826AWG T80
IEC 60335-2-80
Tested in
the
appliance
UL E315723
Alt.
ZHONG SHAN
YONG ROI
ELECTRIC
FACTORY
CO LTD
1015 / 1007 /
2464
600V / 300V~, 1826AWG T80
IEC 60335-2-80
Tested in
the
appliance
UL E204893
TRF No. IEC60335_2_80E
Tf
Page 94 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Plastic material
for enclosure,
base,
switch/control
button
Chi Mei
Corporation
PA-764 +
ABS ,V-0
IEC 60335-2-80
Thickness of
enclosure: 2,1 mm
Tested in
appliance
UL E56070
Heat shrinkable
tube (KN-2903,
KN-2905 for
internal wires,
other models for
motor leader
wires only)
Alt.
Shenzhen Woer
Heat-Shrinkable
Material Co., Ltd.
RSFR-H
600V T125
IEC 60335-2-80
Tested in
appliance
UL E203950
DONGGUAN
SALIPT CO LTD
SALIPT S901-600
600V T125
IEC 60335-2-80
Tested in
appliance
UL E209436
Holder for wire
connector
(except for KN2903)
FOSHAN
SHUNDE KENDA
ELECTRICAL
FACTOTY
CT-2
3A
IEC 60335-2-80
Tested in
appliance/
PCB
Jiang Men Chang CM-1
Ming PCB Factory
V-0
IEC 60335-2-80
Tested in
appliance
UL E232206
Holder of fan
motor
Petrochina
Company Limited
0215F
ABS ,V-0
IEC 60335-2-80
Tested in
appliance
UL E243093
Current fuse for
KN-2903 &
KN-2905 only
Shenzhen Lanson
Electronics Co.
Ltd.
3K T1A250V
1A, 250V
IEC 60127-1
VDE
40010682
334-Series(s)
1A, 250V
IEC 60127-1
VDE
40025428
SS22F25G7
DC 50V 0,3A
IEC 60335-2-80
Tested in
appliance
Switch for model KEXIN
KN-2905
SS22F25G9
DC 50V 0,3A
IEC 60335-2-80
Tested in
appliance
Switches for
models
KN-2926H,
KN-2918H,
KN-2926,
KN-2924,
KN-2916H,
KN-2914H,
KN-2916,
KN-2914
KN-2912
KN-2712
SS43D015GB DC 50V 0,3A
5
IEC 60335-2-80
Tested in
appliance
Alt.
Dongguan Better
Electronic
Technology Co.,
Ltd.
Switch for model KEXIN
KN-2903
HENG MEI
ELECTRONICS
CO., LTD.
TRF No. IEC60335_2_80E
Page 95 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Battery for
KN-2926HR,
KN-2918HR,
KN-2926H,
KN-2918H,
KN-2926,
KN-2924
Alt.
Battery for
KN-2916HR,
KN-2914HR,
KN-2916H,
KN-2914H,
KN-2916,
KN-2914
Alt.
Result - Remark
Verdict
Chee Yuen Plastic RB1245B
Product (Huizhou)
Co.Ltd.
12V/4,5Ah
Sealed lead-acid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
Kennede
Electronics MFG.
Co., Ltd.
12V/4,5Ah
Sealed lead-acid
rechargeable
battery
6V/7Ah Sealed
lead-acid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
Tested in
appliance
6V/7Ah Sealed
lead-acid
rechargeable
battery
6V/4,5Ah Sealed
lead-acid
rechargeable
battery
6V/4,5Ah Sealed
lead-acid
rechargeable
battery
4V/1,6Ah Sealed
lead-acid
rechargeable
battery
4V/1,6Ah Sealed
lead-acid
rechargeable
battery
4V/0,9Ah Sealed
lead-acid
rechargeable
battery
4V/0,9Ah Sealed
lead-acid
rechargeable
battery
AC250V, 3A
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
Tested in
appliance
IEC 60335-2-80
PS, HB
IEC 60335-2-80
Tested in
appliance
Tested in
appliance
UL E56070
RB1245B
Chee Yuen Plastic RB670B
Product (Huizhou)
Co.Ltd.
Kennede
Electronics MFG.
Co., Ltd.
RB670B
Battery for
KN-2912,
KN-2712
Chee Yuen Plastic RB645B
Product (Huizhou)
Co.Ltd.
Alt.
Kennede
Electronics MFG.
Co., Ltd.
Battery for
KN-2905
Chee Yuen Plastic RB416B
Product (Huizhou)
Co.Ltd.
Alt.
Kennede
Electronics MFG.
Co., Ltd.
Battery for
KN-2903
Chee Yuen Plastic RB409B
Product (Huizhou)
Co.Ltd.
Alt.
Kennede
Electronics MFG.
Co., Ltd.
RB645B
RB416B
RB409B
Weak part (other Zhongshan Sanhe 2F
fuse)
Electronic Co., Ltd
Lamp cover
CHI MEI
PG-33
CORPORATION
TRF No. IEC60335_2_80E
Page 96 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Supplementary information:
1
) Provided evidence ensures the agreed level of compliance. See OD-CB2039.
28.1
N/A
TABLE: Threaded part torque test
Threaded part identification
Diameter of thread
(mm)
Column number
(I, II, or III)
Applied torque (Nm)
Supplementary information:
29.1
P
TABLE: Clearances
Overvoltage category........................................ ... :
II
Type of insulation:
Rated impulse
voltage (V):
Min. cl (mm)
330
0,2* / 0,5 / 0,8**
500
0,2* / 0,5 / 0,8**
800
0,2* / 0,5 / 0,8**
1 500
0,5 / 0,8** / 1,0***
2 500
1,5 / 2,0***
4 000
3,0 / 3,5***
6 000
5,5 / 6,0***
8 000
8,0 / 8,5***
10 000
11,0 / 11,5***
Basic
(mm)
Supplementary
(mm)
>13,9
3,7
Reinforced
(mm)
Functional Verdict / Remark
(mm)
>3,2
>12,0
P
P
Supplementary information:
*) For tracks on printed circuit boards if pollution degree 1 and 2
**) For pollution degree 3
***) If the construction is affected by wear, distortion, movement of the parts or during assembly
29.2
TABLE: Creepage distances, basic, supplementary and reinforced insulation
Working voltage
(V)
Creepage distance
(mm)
Pollution degree
1
TRF No. IEC60335_2_80E
2
3
Type of insulation
P
Page 97 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Material group
Material group
I
II
IIIa/IIIb
I
II
IIIa/IIIb*
50
0,18
0,6
0,85
1,2
1,5
1,7
1,9
50
0,18
0,6
0,85
1,2
1,5
1,7
1,9
50
0,36
1,2
1,7
2,4
3,0
3,4
3,8
125
0,28
0,75
1,05
1,5
1,9
2,1
2,4
125
0,28
0,75
1,05
1,5
1,9
2,1
2,4
125
0,56
1,5
2,1
3,0
3,8
4,2
4,8
250
0,56
1,25
1,8
2,5
3,2
3,6
4,0
250
0,56
1,25
1,8
2,5
3,2
3,6
4,0
250
1,12
2,5
3,6
5,0
6,4
7,2
8,0
400
1,0
2,0
2,8
4,0
5,0
5,6
6,3
400
1,0
2,0
2,8
4,0
5,0
5,6
6,3
400
2,0
4,0
5,6
8,0
10,0
11,2
12,6
500
1,3
2,5
3,6
5,0
6,3
7,1
8,0
500
1,3
2,5
3,6
5,0
6,3
7,1
8,0
500
2,6
5,0
7,2
10,0
12,6
14,2
16,0
630 and 800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
630 and 800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
630 and 800
3,6
6,4
9,0
12,6
16,0
18,0
20,0
800 and 1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
800 and 1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
800 and 1000
4,8
8,0
11,2
16,0
20,0
22,0
25,0
1000 and 1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
1000 and 1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
1000 and 1250
6,4
10,0
14,2
20,0
25,0
28,0
32,0
1250 and 1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
1250 and 1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
1250 and 1600
8,4
12,6
18,0
25,0
32,0
36,0
40,0
1600 and 2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
1600 and 2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
TRF No. IEC60335_2_80E
Verdict
(mm)
)
B**
)
S**)
R**)
Verdict
P
>18,
9
4,5
P
>13,
5
P
Page 98 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
1600 and 2000
11,2
16,0
22,0
32,0
40,0
44,0
50,0
2000 and 2500
7,5
10,0
14,0
20,0
25,0
28,0
32,0
2000 and 2500
7,5
10,0
14,0
20,0
25,0
28,0
32,0
2000 and 2500
15,0
20,0
28,0
40,0
50,0
56,0
64,0
2500 and 3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
2500 and 3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
>2500 and 3200
20,0
25,0
36,0
50,0
64,0
72,0
80,0
3200 and 4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
3200 and 4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
3200 and 4000
25,0
32,0
44,0
64,0
80,0
90,0
100,0
4000 and 5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
4000 and 5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
4000 and 5000
32,0
40,0
56,0
80,0
100,0
112,0
126,0
5000 and 6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
5000 and 6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
5000 and 6300
40,0
50,0
72,0
100,0
126,0
142,0
160,0
6300 and 8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
6300 and 8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
6300 and 8000
50,0
64,0
90,0
126,0
160,0
180,0
200,0
8000 and 10000
32,0
40,0
56,0
80,0
100,0
110,0
125,0
8000 and 10000
32,0
40,0
56,0
80,0
100,0
110,0
125,0
8000 and 10000
64,0
80,0
112,0
160,0
200,0
220,0
250,0
10000 and 12500 40,0
50,0
71,0
100,0
125,0
140,0
160,0
10000 and 12500 40,0
50,0
71,0
100,0
125,0
140,0
160,0
10000 and 12500 80,0 100,0
142,0
200,0
250,0
280,0
320,0
Verdict
Supplementary information:
*) Material group IIIb is allowed if the working voltage does not exceed 50 V
**) B = Basic insulation, S = Supplementary insulation, R = Reinforced insulation
29.2
TABLE: Creepage distances, functional insulation
Working voltage
(V)
Creepage distance
(mm)
Pollution degree
1
TRF No. IEC60335_2_80E
2
3
P
Page 99 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Material group
Material group
I
II
IIIa/IIIb
I
II
IIIa/IIIb*)
10
0,08
0,4
0,4
0,4
1,0
1,0
1,0
50
0,16
0,56
0,8
1,0
1,4
1,6
1,8
125
0,25
0,71
1,0
1,4
1,8
2,0
2,2
250
0,42
1,0
1,4
2,0
2,5
2,8
3,2
400
0,75
1,6
2,2
3,2
4,0
4,5
5,0
500
1,0
2,0
2,8
4,0
5,0
5,6
6,3
630 and 800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
800 and 1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
1000 and 1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
1250 and 1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
1600 and 2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
2000 and 2500
7,5
10,0
14,0
20,0
25,0
28,0
32,0
2500 and 3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
3200 and 4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
4000 and 5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
5000 and 6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
6300 and 8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
8000 and 10000
32,0
40,0
56,0
80,0
100,0
110,0
125,0
10000 and 12500 40,0
50,0
71,0
100,0
125,0
140,0
160,0
Supplementary information:
*) Material group IIIb is allowed if the working voltage does not exceed 50 V
TRF No. IEC60335_2_80E
Verdict
Verdict / Remark
P / 3,21mm
Page 100 of 101
Report No. 247910
IEC 60335-2-80
Clause
Requirement - Test
30
TABLE: Resistance to heat and fire
Object/
part No.
Manufacturer
/
trademark
Type/
model
Ball pressure test
°C
(mm) with limit 2,0 mm
75
Plastic
material for
enclosure,
base, Switch
button
Chi Mei
Corporation
Holder of fan
motor
Petrochina
Company
Limited
Bobbin of
transformer
Chang Chun
Plastics Co
Ltd
Chang Chun
Plastics Co
Ltd
E I DUPONT
DE
Alt.
Alt.
TRF No. IEC60335_2_80E
PA764
+
Result - Remark
125
cl. 11
+40
cl. 19
+25
Glow wire test
(GWT)
°C
550
1,2
1,6m
m,
97°C
0215F
650
te
750
ti
Glow-wire
flammability index
(GWFI)
°C
850
te
ti
0
0
Verdict
P
P
550
650
750
850
Glowwire
ignition
temp.
(GWIT)
°C
675
Needle
- flame
test
(NFT)
Verdict
775
P
P
T375J
1,2
0
0
P
P
4115
(a)
1,2
0
0
P
P
FR50(
+)(f1)
1,2
0
0
P
P
Page 101 of 101
Report No. 247910
IEC 60335-2-80
Clause
PCB
Holder for
wire
connector
Requirement - Test
NEMOURS
& CO INC
Jiang
Men
Chang Ming
Pcb Factory
FOSHAN
SHUNDE
KENDA
ELECTRICA
L FACTOTY
Lamp cover
CHI MEI
CORPORATI
ON
Supplementary information:
1)
Result - Remark
CM-1
0,8
0
0
P
P
CT-2
1,6
0
0
P
P
PG-33
1,3
P
Parts of material classified at least HB40 or if relevant HBF
Parts of material classified as V-0 or V-1
Flame persisting longer than 2 s (= te – ti) need only be reported for unattended appliances
4)
Surrounding parts subjected to the needle-flame test of annex E
5)
Base material classified as V-0 or if relevant VTM-0
6)
The GWIT pre-selection option, the 850 °C GWFI pre-selection option, and the 850 °C GWT are not applicable for attended appliances
2)
3)
TRF No. IEC60335_2_80E
Verdict
P
Page 1 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Attachment: Photos
Overview of model KN-2926
Internal view of model KN-2926
TRF No. IEC60335_2_80E
Verdict
Page 2 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Appliance inlet
DC inlet on the control panel
TRF No. IEC60335_2_80E
Verdict
Page 3 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Motor of model KN-2926
Control panel of model KN-2926
TRF No. IEC60335_2_80E
Verdict
Page 4 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Front control PCB of model KN-2926
Back control PCB of model KN-2926
TRF No. IEC60335_2_80E
Verdict
Page 5 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Front power PCB of model KN-2926
Back power PCB of model KN-2926
TRF No. IEC60335_2_80E
Verdict
Page 6 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of transformer on model KN-2926
Overview of transformer on model KN-2926
TRF No. IEC60335_2_80E
Verdict
Page 7 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Internal view of transformer on model KN-2926
Thermal fuse on transformer on model KN-2926
TRF No. IEC60335_2_80E
Verdict
Page 8 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2712
Control panel of model KN-2712
TRF No. IEC60335_2_80E
Verdict
Page 9 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Internal view of model KN-2712
Internal view of model KN-2712
TRF No. IEC60335_2_80E
Verdict
Page 10 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Motor of model KN-2712 (model KRS-55 STP-3
Motor of model KN-2712 (model SH-55 STP-3
TRF No. IEC60335_2_80E
-117D)
-117D)
Verdict
Page 11 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Front power PCB of model KN-2712
Back power PCB of model KN-2712
TRF No. IEC60335_2_80E
Verdict
Page 12 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of transformer on model KN-2712
Internal view of transformer on model KN-2712
TRF No. IEC60335_2_80E
Verdict
Page 13 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Internal view of transformer (bobbin) on model KN-2712
Thermal fuse on transformer on model KN-2712
TRF No. IEC60335_2_80E
Verdict
Page 14 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2918HR
Internal view of model KN-2918HR
TRF No. IEC60335_2_80E
Verdict
Page 15 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Internal view of model KN-2918HR
Motor of model KN-2918HR
TRF No. IEC60335_2_80E
Verdict
Page 16 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Control panel of model KN-2918HR
Front power PCB of model KN-2918HR
TRF No. IEC60335_2_80E
Verdict
Page 17 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Front power PCB of model KN-2918HR
Overview of transformer on model KN-2918HR
TRF No. IEC60335_2_80E
Verdict
Page 18 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of transformer on model KN-2918HR
Internal view of transformer (bobbin) on model 2918HR
TRF No. IEC60335_2_80E
Verdict
Page 19 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Thermal fuse on transformer on model 2918HR
Overview of model KN-2905
TRF No. IEC60335_2_80E
Verdict
Page 20 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Internal view of model KN-2905
Internal view of model KN-2905
TRF No. IEC60335_2_80E
Verdict
Page 21 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Control panel of model KN-2905
motor of model KN-2905
TRF No. IEC60335_2_80E
Verdict
Page 22 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Front Commutator PCB on model KN-2905
Back commutator PCB on model KN-2905
TRF No. IEC60335_2_80E
Verdict
Page 23 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Front overview of LED lamp PCB1 on model KN-2905
Back overview of LED lamp PCB1 on model KN-2905
TRF No. IEC60335_2_80E
Verdict
Page 24 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Front overview of LED lamp PCB2 on model KN-2905
Back overview of LED lamp PCB2 on model KN-2905
TRF No. IEC60335_2_80E
Verdict
Page 25 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2903
Overview of model KN-2912
TRF No. IEC60335_2_80E
Verdict
Page 26 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2914
Overview of model KN-2916
TRF No. IEC60335_2_80E
Verdict
Page 27 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2924
Overview of model KN-2914H
TRF No. IEC60335_2_80E
Verdict
Page 28 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2916H
Overview of model KN-2918H
TRF No. IEC60335_2_80E
Verdict
Page 29 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2926H
Overview of model KN-2914HR
TRF No. IEC60335_2_80E
Verdict
Page 30 of 30
Report No. 247910
IEC60335_2_80E - ATTACHMENT
Clause
Requirement - Test
Result - Remark
Overview of model KN-2916HR
Overview of model KN-2926HR
TRF No. IEC60335_2_80E
Verdict
Test Report issued under the responsibility of
www.nemko.com
TEST REPORT
IEC 60598-2-4
Luminaires
Part 2: Particular requirements:
Section Four – Portable general purpose luminaires
Report Number............................... :
247910
Date of issue .................................. :
2014-01-08
Total number of pages ....................
80 pages (including attachments)
Applicant’s name ........................... :
KENNEDE ELECTRONIC MFG CO., LTD.
Address .......................................... :
No. 21 Jintong Road, Tangxia Town, Pengjiang District, Jiangmen
City, Guangdong Province, China.
Test specification:
Standard ......................................... :
IEC 60598-2-4 (Second Edition):1997 used in conjunction with
IEC 60598-1 (Second Edition):2008
Test procedure ............................... :
Compliance test
Non-standard test method………..:
N/A
Test Report Form No. .................... :
IEC60598_2_4B
Test Report Form(s) Originator ................... :
Intertek Semko AB
Master TRF .................................................... :
2013-02
Copyright © 2013 Worldwide System for Conformity Testing and Certification of Electrotechnical
Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
Test item description..................... :
Rechargeable Fan with LED module
Trade Mark ...................................... :
Manufacturer .................................. :
Same as Applicant
Model/Type reference .................... :
KN-29xxx series (see General product information for detailed
information)
Ratings ............................................ :
24 W or 30 W 220-240 V~ 50/60 Hz; Cl. II, ta = 40 oC.
This Test Report, when bearing the Nemko name and logo is only valid when issued by a Nemko laboratory,
or by a laboratory having special agreement with Nemko.
Page 2 of 43
Report No.: 247910
Testing procedure and testing location:
Testing Laboratory:
Nemko Hong Kong Ltd.
Testing location/ address .......................... : Unit 1-5, 15/F, CCT Telecom Building, No. 11 Wo Shing
Street, Fotan, Shatin, N.T., Hong Kong
Associated Laboratory:
Testing location/ address .......................... :
Tested by (name + signature) ........ : Eva Dai
Approved by (+ signature) .............. : Benny Lan
Testing procedure: TMP
Testing location/ address .......................... :
Tested by (name + signature) ........ :
Approved by (+ signature) .............. :
Testing procedure: WMT
Testing location/ address .......................... :
Tested by (name + signature) ........ :
Witnessed by (+ signature)............. :
Approved by (+ signature) .............. :
Testing procedure: SMT
Testing location/ address .......................... :
Tested by (name + signature) ........ :
Approved by (+ signature) .............. :
Supervised by (+ signature) ........... :
TRF No. IEC60598_2_4B
Page 3 of 43
Report No.: 247910
List of Attachments (including a total number of pages in each attachment):
Attachment 1: European Group Differences and National Differences ( 2 pages)
Attachment 2: Addition test according to IEC 62031:2008+A1:2012 (7 pages)
Attachment 3: Pictures (28 pages)
Summary of testing:
Tests performed (name of test and test clause):
The test samples are complying with the relevant
product standard(s) and all applicable test clauses.
Testing location:
Nemko Hong Kong Ltd.
Unit 1-5, 15/F, CCT Telecom Building, No. 11 Wo
Shing Street, Fotan, Shatin, N.T., Hong Kong
The self-ballasted LED modules have been tested
according to IEC/EN 62031.
The LED modules used in these products have been
tested according to IEC/EN 62471, the retinal blue
light hazard or thermal hazard was classified as
Exempt Group when LED lighted for all models
except models KN-2903, KN-2905 classified as Risk
1.
For detailed information refer to the test report
issued by EMTEK with report No. ED140122125S,
ED140122126S, ED140122127S, ED140122128S.
Summary of compliance with National Differences:
List of countries addressed:
-
CENELEC members
The product fulfils the requirements of EN 60598-2-4:1997 used in conjunction with
EN 60598-1:2008+A11:2009.
TRF No. IEC60598_2_4B
Page 4 of 43
Report No.: 247910
Copy of marking plate
The artwork below may be only a draft. The use of certification marks on a product must be authorized by
the respective NCBs that own these marks.
Calibration:
All instruments used in the tests given in this test report are calibrated and
traceable to national or international standards.
Further information about traceability will be given on request.
Measurement
uncertainty:
Measurement uncertainties are calculated for all instruments and instrument
set-ups given in this report. Calculations are based on the principles given in
the standard EA-4/02 (Dec. 1999), IEC Guide 115:2007, Nemko routine L227
and other relevant internal Nemko-procedures.
Further information about measurement uncertainties will be given on request.
Evaluation of results: If not explicitly stated otherwise in the standard, the test is passed if the
measured value is equal to or below (above) the limit line, regardless of the
measurement uncertainty. If the measured value is above (below) the limit line,
the test is not passed - ref IEC Guide 115:2007, and Nemko routine L220. The
instrumentation accuracy is within limits agreed by IECEE-CTL (ref. Nemko
routine L227).
TRF No. IEC60598_2_4B
Page 5 of 43
Report No.: 247910
Test item particulars............................................... :
Classification of installation and use......................... :
Portable and normal use
Supply Connection.................................................... :
Appliance inlet, detachable cord with plug and
connector is delivered together with the appliance,
and/or DC inlet
.................................................................................. :
.................................................................................. :
Possible test case verdicts:
- test case does not apply to the test object ............. :
N/A
- test object does meet the requirement ................... :
P (Pass)
- test object does not meet the requirement ............. :
F (Fail)
Testing ..................................................................... :
Date of receipt of test item ........................................ :
2013-12-10
Date (s) of performance of tests ............................... :
2013-12-10 to 2014-01-08
TRF No. IEC60598_2_4B
Page 6 of 43
Report No.: 247910
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.
Throughout this report a
comma /
point is used as the decimal separator.
Clause numbers between brackets refer to clauses in IEC 60598-1
Manufacturer’s Declaration per sub-clause 4.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory has
been provided ..............................................................:
Yes
Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) ...................... : Same as Applicant / Manufacturer
General product information:
LED module for rechargeable fan use, incorporated with the integral d.c. supplied electronic circuit for LED
module, the integral electronic circuit is supplied by the included rechargeable battery.
Class II, for indoor use only.
Main model KN-29xxx series:
The “xxx” in the type designation can be 12, 14, 16, 24, 26, 14H, 16H, 18H or 26H.
30 W or 24 W 220-240 V~ 50/60 Hz; Cl. II, ta = 40 oC
Variant 1: KN-290y series
The y in the type designation can be 3 or 5.
4 W or 5 W 220-240 V~ 50/60 Hz; Cl. II, ta = 40 oC
Variant 2: KN-29zzHR series
The zz in the type designation can be 14, 16, 18 or 26.
24 W or 30 W 220-240 V~ 50/60 Hz; Cl. II, ta = 40 oC.
Variant 3: KN-2712
24 W 220-240 V~ 50/60 Hz; Cl. II, ta = 40 oC.
TRF No. IEC60598_2_4B
Page 7 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
4.2 (0)
GENERAL TEST REQUIREMENTS
4.2 (0.1)
Information for luminaire design considered
Result - Remark
P
Standard
Yes
No
4.2 (0.3)
More sections applicable ........................................: Yes
4.4 (2)
CLASSIFICATION
4.4 (2.2)
Type of protection (Class 0 excluded) .................. : Class II
4.4 (2.3)
Degree of protection (Requirement: Ordinary) ..... : IP20
4.4 (2.4)
Luminaire suitable for direct mounting on normally Yes
flammable surfaces .............................................. :
No
Luminaire not suitable for direct mounting on
Yes
normally flammable surfaces................................ :
No
Luminaire for normal use ..................................... : Yes
No
Luminaire for rough service ................................. : Yes
No
4.4 (2.5)
Verdict
No
P
4.5 (3)
MARKING
P
4.5 (3.2)
Mandatory markings
P
Position of the marking
P
Format of symbols/text
P
Additional information
P
4.5 (3.3)
Language of instructions
English
P
4.5 (3.3.1)
Combination luminaires
N/A
4.5 (3.3.2)
Nominal frequency in Hz
N/A
4.5 (3.3.3)
Operating temperature
N/A
4.5 (3.3.4)
Symbol or warning notice
N/A
4.5 (3.3.5)
Wiring diagram
N/A
4.5 (3.3.6)
Special conditions
N/A
4.5 (3.3.7)
Metal halide lamp luminaire – warning
N/A
4.5 (3.3.8)
Limitation for semi-luminaires
N/A
4.5 (3.3.9)
Power factor and supply current
N/A
o
4.5 (3.3.10)
Suitability for use indoors
4.5 (3.3.11)
Luminaires with remote control
N/A
4.5 (3.3.12)
Clip-mounted luminaire – warning
N/A
4.5 (3.3.13)
Specifications of protective shields
N/A
TRF No. IEC60598_2_4B
ta = 40 C
P
Page 8 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
4.5 (3.3.14)
Symbol for nature of supply
N/A
4.5 (3.3.15)
Rated current of socket outlet
N/A
4.5 (3.3.16)
Rough service luminaire
N/A
4.5 (3.3.17)
Mounting instruction for type Y, type Z and some
type X attachments
4.5 (3.3.18)
Non-ordinary luminaires with PVC cable
N/A
4.5 (3.3.19)
Protective conductor current in instruction if
applicable
N/A
4.5 (3.3.20)
Provided with information if not intended to be
mounted within arms reach
N/A
4.5 (3.4)
Test with water
P
Test with hexane
P
Legible after test
P
Label attached
P
4.6 (4)
CONSTRUCTION
P
4.6 (4.2)
Components replaceable without difficulty
N/A
4.6 (4.3)
Wireways smooth and free from sharp edges
N/A
4.6 (4.4)
Lampholders
N/A
4.6 (4.4.1)
Integral lampholder
N/A
4.6 (4.4.2)
Wiring connection
N/A
4.6 (4.4.3)
Lampholder for end-to-end mounting
N/A
4.6 (4.4.4)
Positioning
N/A
- pressure test (N) ................................................ :
N/A
After test the lampholder comply with relevant
standard sheets and show no damage
N/A
After test on single-capped lampholder the
lampholder have not moved from its position and
show no permanent deformation
N/A
- bending test (Nm) .............................................. :
N/A
After test the lampholder have not moved from its
position and show no permanent deformation
N/A
4.6 (4.4.5)
Peak pulse voltage
N/A
4.6 (4.4.6)
Centre contact
N/A
4.6 (4.4.7)
Parts in rough service luminaires resistant to
tracking
N/A
4.6 (4.4.8)
Lamp connectors
N/A
TRF No. IEC60598_2_4B
Result - Remark
Type X
Verdict
P
Page 9 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
4.6 (4.4.9)
Caps and bases correctly used
N/A
4.6 (4.5)
Starter holders
N/A
Starter holder in luminaires other than class II
N/A
Starter holder class II construction
N/A
Terminal blocks
N/A
Tails
N/A
Unsecured blocks
N/A
4.6 (4.6)
Result - Remark
Verdict
4.6 (4.7)
Terminals and supply connections
P
4.6 (4.7.1)
Contact to metal parts
P
4.6 (4.7.2)
Test 8 mm live conductor
N/A
Test 8 mm earth conductor
N/A
4.6 (4.7.3)
Terminals for supply conductors
N/A
4.6 (4.7.3.1)
Welded connections:
N/A
- stranded or solid conductor
N/A
- spot welding
N/A
- welding between wires
N/A
- Type Z attachment
N/A
- mechanical test according to 15.8.2
N/A
- electrical test according to 15.9
N/A
- heat test according to 15.9.2.3 and 15.9.2.4
N/A
4.6 (4.7.4)
Terminals other than supply connection
4.6 (4.7.5)
Heat-resistant wiring/sleeves
N/A
4.6 (4.7.6)
Multi-pole plug
N/A
- test at 30 N
N/A
Switches:
N/A
- adequate rating
N/A
- adequate fixing
N/A
- polarized supply
N/A
- compliance with 61058-1 for electronic switches
N/A
4.6 (4.9)
Insulating lining and sleeves
N/A
4.6 (4.9.1)
Retainment
N/A
Method of fixing .................................................... :
N/A
Insulated linings and sleeves
N/A
Resistant to a temperature > 20 C to the wire
temperature or
N/A
4.6 (4.8)
4.6 (4.9.2)
TRF No. IEC60598_2_4B
P
Page 10 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
a) & c) Insulation resistance and electric strength
N/A
b) Ageing test. Temperature ( C) ......................... :
N/A
4.6 (4.10)
Insulation of Class II luminaires
4.6 (4.10.1)
No contact, mounting surface – accessible metal
parts – wiring of basic insulation
N/A
Safe installation fixed luminaires
N/A
Capacitors and switches
N/A
Interference suppression capacitors according to
IEC 60384-14
N/A
4.6 (4.10.2)
4.6 (4.10.3)
P
Assembly gaps:
P
- not coincidental
P
- no straight access with test probe
P
Retainment of insulation:
N/A
- fixed
N/A
- unable to be replaced; luminaire inoperative
N/A
- sleeves retained in position
N/A
- lining in lampholder
N/A
4.6 (4.11)
Electrical connections
P
4.6 (4.11.1)
Contact pressure
N/A
4.6 (4.11.2)
Screws:
N/A
- self-tapping screws
N/A
- thread-cutting screws
N/A
Screw locking:
N/A
- spring washer
N/A
- rivets
N/A
4.6 (4.11.3)
4.6 (4.11.4)
Material of current-carrying parts
P
4.6 (4.11.5)
No contact to wood or mounting surface
P
4.6 (4.11.6)
Electro-mechanical contact systems
N/A
4.6 (4.12)
Mechanical connections and glands
P
4.6 (4.12.1)
Screws not made of soft metal
P
Screws of insulating material
N/A
Torque test: torque (Nm); part .............................. : 0,5 Nm; Screw fixed the PCB,
Ø 3,0 mm
P
Torque test: torque (Nm); part .............................. : 0,5 Nm; Screw fixed the lamp
cover, Ø 3,0 mm
P
Torque test: torque (Nm); part .............................. :
TRF No. IEC60598_2_4B
N/A
Page 11 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
4.6 (4.12.2)
Screws with diameter < 3 mm screwed into metal
N/A
4.6 (4.12.4)
Locked connections:
N/A
- fixed arms; torque (Nm) ...................................... :
N/A
- lampholder; torque (Nm)..................................... :
N/A
- push-button switches; torque 0,8 Nm ................. :
N/A
4.6 (4.12.5)
Screwed glands; moment (Nm) ............................ :
N/A
4.6 (4.13)
Mechanical strength
P
4.6 (4.13.1)
Impact tests:
P
- fragile parts; energy (Nm) ................................... :
P
- other parts; energy (Nm) .................................... : Lamp cover; 0,5 Nm
Lamp enclosure; 0,5 Nm
Battery compartment; 0,5 Nm
P
1) live parts
P
2) linings
Result - Remark
Verdict
N/A
3) protection
P
4) covers
P
4.6 (4.13.3)
Straight test finger
P
4.6 (4.13.4)
Rough service luminaires
N/A
- IP54 or higher
N/A
a) fixed
N/A
b) hand-held
N/A
c) delivered with a stand
N/A
d) for temporary installations and suitable for
mounting on a stand
N/A
4.6 (4.13.6)
Tumbling barrel
N/A
4.6 (4.14)
Suspensions and adjusting devices
N/A
4.6 (4.14.1)
Mechanical load:
N/A
A) four times the weight
N/A
B) torque 2,5 Nm
N/A
C) bracket arm; bending moment (Nm) ................ :
N/A
D) load track-mounted luminaires
N/A
E) clip-mounted luminaires, glass-shelve.
Thickness (mm) ................................................... :
N/A
Metal rod. diameter (mm) .................................... :
N/A
Fixed luminaire or independent control gear
without fixing devices
N/A
TRF No. IEC60598_2_4B
Page 12 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
4.6 (4.14.2)
Load to flexible cables
N/A
Mass (kg) ............................................................. :
N/A
Stress in conductors (N/mm²) .............................. :
N/A
Mass (kg) of semi-luminaire ................................ :
N/A
Bending moment (Nm) of semi-luminaire ............ :
N/A
Adjusting devices:
N/A
- flexing test; number of cycles ............................. :
N/A
- strands broken
N/A
- electric strength test afterwards
N/A
4.6 (4.14.4)
Telescopic tubes: cords not fixed to tube; no
strain on conductors
N/A
4.6 (4.14.5)
Guide pulleys
N/A
4.6 (4.14.6)
Strain on socket-outlets
N/A
4.6 (4.15)
Flammable materials:
P
- glow-wire test 650 C
N/A
- spacing
N/A
4.6 (4.14.3)
Result - Remark
30 mm
- screen withstanding test of 13.3.1
N/A
- screen dimensions
N/A
- no fiercely burning material
4.6 (4.15.2)
4.6 (4.16)
4.6 (4.16.1)
4.6 (4.16.2)
Verdict
P
- thermal protection
N/A
- electronic circuits exempted
N/A
Luminaires made of thermoplastic material with lamp control gear
P
a) construction
P
b) temperature sensing control
N/A
c) surface temperature
N/A
Luminaires for mounting on normally flammable surfaces
P
No lamp control gear
P
Electronic control gear
(compliance with Section 12)
Lamp control gear spacing:
N/A
- spacing 35 mm
N/A
- spacing 10 mm
N/A
Thermal protection:
N/A
- in lamp control gear
N/A
- external
N/A
- fixed position
N/A
TRF No. IEC60598_2_4B
Page 13 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
- temperature marked lamp control gear
Verdict
N/A
4.6 (4.16.3)
Design to satisfy the test of 12.6
(see 12.6)
4.6 (4.17)
Drain holes
N/A
Clearance at least 5 mm
N/A
4.6 (4.18)
Resistance to corrosion:
N/A
4.6 (4.18.1)
- rust-resistance
N/A
4.6 (4.18.2)
- season cracking in copper
N/A
4.6 (4.18.3)
- corrosion of aluminium
N/A
4.6 (4.19)
Ignitors compatible with ballast
N/A
4.6 (4.20)
Rough service vibration
N/A
4.6 (4.21)
Protective shield:
N/A
4.6 (4.21.1)
Shield fitted
N/A
Shield of glass if tungsten halogen lamps
N/A
4.6 (4.21.2)
Particles from a shattering lamp not impair safety
N/A
4.6 (4.21.3)
No direct path
N/A
4.6 (4.21.4)
Impact test on shield
N/A
Glow-wire test on lamp compartment
N/A
4.6 (4.22)
Attachments to lamps
N/A
4.6 (4.23)
Semi-luminaires comply Class II
N/A
4.6 (4.24)
UV radiation for tungsten halogen lamps and
metal halide lamps (Annex P)
N/A
4.6 (4.25)
No sharp point or edges
P
4.6 (4.26)
Short-circuit protection:
N/A
4.6 (4.26.1)
Uninsulated accessible SELV parts
N/A
4.6 (4.26.2)
Short-circuit test
N/A
4.6 (4.26.3)
Test chain according to Figure 29
N/A
4.6.1 (-)
Insulation not damaged when placing on support
N/A
4.6.2 (-)
Wiring fixed, to avoid rubbing
P
4.6.3 (-)
Stability 6
P
4.6.4 (-)
Candlestick luminaires with switch
N/A
4.6.5 (-)
E5 lampholders
N/A
4.7 (11)
CREEPAGE DISTANCES AND CLEARANCES
Working voltage (V) .............................................. : 240 V
TRF No. IEC60598_2_4B
N/A
P
Page 14 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Voltage form
Sinusoidal
Non-sinusoidal
PTI
< 600
Impulse withstand category (Normal category II)
(Category III Annex U)
Category II
Verdict
> 600
Category III
Rated pulse voltage (kV) ...................................... :
(1) Current-carrying parts of different polarity: cr
cr > 3,2 (> 2,5)
(mm); cl (mm) ....................................................... : cl > 2,0 (> 1,5)
P
(2) Current-carrying parts and accessible parts: cr cr > 6,5 (> 5,0)
(mm); cl (mm) ....................................................... : cl > 3,9 (> 3,0)
P
(3) Parts becoming live due to breakdown of
basic insulation and metal parts:
cr (mm); cl (mm) ................................................... :
N/A
(4) Outer surface of cable where it is clamped and
metal parts: cr (mm); cl (mm)................................ :
N/A
(5) Not used
(6) Current-carrying parts and supporting surface: cr > 6,5 (> 5,0)
cr (mm); cl (mm) ................................................... : cl > 3,9 (> 3,0)
P
4.8 (7)
PROVISION FOR EARTHING
N/A
4.8 (7.2.1
+ 7.2.3)
Accessible metal parts
N/A
Metal parts in contact with supporting surface
N/A
Resistance < 0,5
N/A
Self-tapping screws used
N/A
Thread-forming screws
N/A
Thread-forming screw used in a grove
N/A
Earth makes contact first
N/A
4.8 (7.2.2
+ 7.2.3)
Earth continuity in joints etc.
N/A
4.8 (7.2.4)
Locking of clamping means
N/A
Compliance with 4.7.3
N/A
Terminal blocks with integrated screwless
earthing contacts tested according Annex V
N/A
4.8 (7.2.5)
Earth terminal integral part of connector socket
N/A
4.8 (7.2.6)
Earth terminal adjacent to mains terminals
N/A
4.8 (7.2.7)
Electrolytic corrosion of the earth terminal
N/A
4.8 (7.2.8)
Material of earth terminal
N/A
TRF No. IEC60598_2_4B
Page 15 of 43
Report No.:247910
IEC 60598-2-4
Clause
4.8 (7.2.10)
4.8 (7.2.11)
4.9 (14)
4.9 (15)
Requirement + Test
Result - Remark
Verdict
Contact surface bare metal
N/A
Class II luminaire for looping-in
N/A
Double or reinforced insulation to functional earth
N/A
Earthing core coloured green-yellow
N/A
Length of earth conductor
N/A
SCREW TERMINALS
N/A
Separately approved; component list
(see Annex 1)
N/A
Part of the luminaire
(see Annex 3)
N/A
SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS
P
Separately approved; component list
Appliance inlet (see Annex 1)
P
Part of the luminaire
(see Annex 4)
N/A
4.10 (5)
EXTERNAL AND INTERNAL WIRING
P
4.10 (5.2)
Supply connection and external wiring
P
4.10 (5.2.1)
Means of connection............................................. : Appliance inlet, detachable
cord with plug and connector is
delivered together with the
appliance
P
4.10 (5.2.2)
Type of cable ........................................................ : H03VVH2-F / H05VVH2-F
P
Nominal cross-sectional area (mm²)..................... : 2 x 0,75
P
Cables equal to IEC 60227 or IEC 60245
P
4.10 (5.2.3)
Type of attachment, X, Y or Z
Type X
P
4.10 (5.2.5)
Type Z not connected to screws
4.10 (5.2.6)
Cable entries:
P
- suitable for introduction
P
- adequate degree of protection
P
N/A
4.10 (5.2.7)
Cable entries through rigid material have rounded
edges
N/A
4.10 (5.2.8)
Insulating bushings:
N/A
- suitably fixed
N/A
- material in bushings
N/A
- material not likely to deteriorate
N/A
- tubes or guards made of insulating material
N/A
Locking of screwed bushings
N/A
4.10 (5.2.9)
TRF No. IEC60598_2_4B
Page 16 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
4.10 (5.2.10)
Cord anchorage:
P
- covering protected from abrasion
P
- clear how to be effective
P
- no mechanical or thermal stress
P
- no tying of cables into knots etc.
P
- insulating material or lining
N/A
Cord anchorage for type X attachment:
N/A
a) at least one part fixed
N/A
b) types of cable
N/A
c) no damaging of the cable
N/A
d) whole cable can be mounted
N/A
e) no touching of clamping screws
N/A
f) metal screw not directly on cable
N/A
g) replacement without special tool
N/A
Glands not used as anchorage
N/A
Labyrinth type anchorages
N/A
4.10
(5.2.10.2)
Adequate cord anchorage for type Y and type Z
attachment
N/A
4.10
(5.2.10.3)
Tests:
N/A
- impossible to push cable; unsafe
N/A
- pull test: 25 times; pull (N) .................................. :
N/A
- torque test: torque (Nm) ..................................... :
N/A
- displacement
N/A
4.10
(5.2.10.1)
2 mm
- no movement of conductors
N/A
- no damage of cable or cord
N/A
4.10 (5.2.11)
External wiring passing into luminaire
N/A
4.10 (5.2.12)
Looping-in terminals
N/A
4.10 (5.2.13)
Wire ends not tinned
P
Wire ends tinned: no cold flow
4.10 (5.2.14)
Mains plug same protection
Class III luminaire plug
4.10 (5.2.16)
N/A
P
N/A
Appliance inlets (IEC 60320)
P
Appliance couplers of class II type
P
TRF No. IEC60598_2_4B
Page 17 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
4.10 (5.2.17)
No standardized interconnecting cables properly
assembled
4.10 (5.2.18)
Used plug in accordance with
P
- IEC 60083
P
N/A
- other standard
4.10 (5.3)
Internal wiring
4.10 (5.3.1)
Internal wiring of suitable size and type
Verdict
N/A
P
26-18 AWG; PVC
P
Through wiring
N/A
- not delivered/ mounting instruction
N/A
- factory assembled
N/A
- socket outlet loaded (A) ...................................... :
N/A
- temperatures ...................................................... : (see Annex 2)
N/A
Green-yellow for earth only
N/A
4.10 (5.3.1.1) Internal wiring connected directly to fixed wiring
N/A
Cross-sectional area (mm²) .................................. :
N/A
Insulation thickness
N/A
Extra insulation added where necessary
N/A
4.10 (5.3.1.2) Internal wiring connected to fixed wiring via internal current-limiting device
Adequate cross-sectional area and insulation
thickness
N/A
N/A
4.10 (5.3.1.3) Double or reinforced insulation for class II
N/A
4.10 (5.3.1.4) Conductors without insulation
N/A
4.10 (5.3.1.5) SELV current-carrying parts
4.10 (5.3.1.6) Insulation thickness other than PVC or rubber
4.10 (5.3.2)
Sharp edges etc.
No moving parts of switches etc.
Joints, raising/lowering devices
4.10 (5.3.3)
4.10 (5.3.4)
P
N/A
P
N/A
P
Telescopic tubes etc.
N/A
No twisting over 360
P
Insulating bushings:
N/A
- suitable fixed
N/A
- material in bushings
N/A
- material not likely to deteriorate
N/A
- cables with protective sheath
N/A
Joints and junctions effectively insulated
N/A
TRF No. IEC60598_2_4B
Page 18 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
4.10 (5.3.5)
Strain on internal wiring
N/A
4.10 (5.3.6)
Wire carriers
N/A
4.10 (5.3.7)
Wire ends not tinned
Wire ends tinned: no cold flow
Result - Remark
Verdict
P
N/A
4.11 (8)
PROTECTION AGAINST ELECTRIC SHOCK
P
4.11 (8.2.1)
Live parts not accessible
P
Basic insulated parts not used on the outer
surface without appropriate protection
P
4.11 (8.2.2)
Basic insulated parts not accessible with standard
test finger on portable and adjustable luminaires
N/A
Basic insulated parts not accessible with Ø 50
mm probe from outside, within arms reach, on
wall-mounted luminaires
N/A
Lampholder and starterholders in portable and
adjustable luminaires comply with double or
reinforced insulation requirements
N/A
Basic insulation only accessible under lamp or
starter replacement
P
Protection in any position
P
Double-ended tungsten filament lamp
N/A
Insulation lacquer not reliable
N/A
Double-ended high pressure discharge lamp
N/A
Relevant warning according to 3.2.18 fitted to the
luminaire
N/A
Portable luminaire adjusted in most unfavourable
position
P
4.11 (8.2.3.a) Class II luminaire:
P
- basic insulated metal parts not accessible during
starter or lamp replacement
N/A
- basic insulation not accessible other than during
starter or lamp replacement
P
- glass protective shields not used as
supplementary insulation
N/A
4.11 (8.2.3.b) BC lampholder of metal in class I luminaires shall
be earthed
N/A
4.11 (8.2.3.c) Class III luminaires with exposed SELV parts:
N/A
Ordinary luminaire:
N/A
- touch current ...................................................... :
N/A
TRF No. IEC60598_2_4B
Page 19 of 43
Report No.:247910
IEC 60598-2-4
Clause
4.11 (8.2.4)
Requirement + Test
Result - Remark
Verdict
- no-load voltage ................................................... :
N/A
Other than ordinary luminaire:
N/A
- nominal voltage ................................................. :
N/A
Portable luminaire:
P
- protection independent of supporting surface
P
- terminal block completely covered
N/A
4.11 (8.2.5)
Compliance with the standard test finger or
relevant probe
P
4.11 (8.2.6)
Covers reliably secured
P
4.11 (8.2.7)
Discharging of capacitors
N/A
0,5 F
Portable plug connected luminaire with capacitor
N/A
Other plug connected luminaire with capacitor
N/A
Discharge device on or within capacitor
N/A
Discharge device mounted separately
N/A
4.12 (12)
ENDURANCE TEST AND THERMAL TEST
P
4.12 (12.3)
Endurance test:
P
- mounting-position ............................................... : Attached to the electronic fan
as normal use
- test temperature ( C) .......................................... : 40 + 10 = 50
- total duration (h) ................................................. : 168
- supply voltage: Un factor; calculated voltage (V) : Battery supplied
- lamp used ........................................................... : Enclosed LED module
4.12 (12.3.2)
After endurance test:
P
- no part unserviceable
P
- luminaire not unsafe
P
- no damage to track system
N/A
- marking legible
P
- no cracks, deformation etc.
P
4.12 (12.4)
Thermal test (normal operation)
(see Annex 2)
P
4.12 (12.5)
Thermal test (abnormal operation)
(see Annex 2)
N/A
4.12 (12.6)
Thermal test (failed lamp control gear condition):
4.12 (12.6.1)
Through wiring or looping-in wiring loaded by a
current of (A) ........................................................ :
- case of abnormal conditions ............................... :
TRF No. IEC60598_2_4B
N/A
Page 20 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
- electronic lamp control gear
Verdict
N/A
- measured winding temperature ( C): at 1,1 Un . :
4.12 (12.6.2)
- measured mounting surface temperature ( C) at
1,1 Un ................................................................... :
N/A
- calculated mounting surface temperature ( C) .. :
N/A
- track-mounted luminaires
N/A
Temperature sensing control
N/A
- case of abnormal conditions ............................... :
- thermal link
N/A
- manual reset cut-out
N/A
- auto reset cut-out
N/A
- measured mounting surface temperature ( C) ... :
N/A
- track-mounted luminaires
N/A
4.12 (12.7)
Thermal test (failed lamp control gear in plastic luminaires):
N/A
4.12 (12.7.1)
Luminaire without temperature sensing control
N/A
4.12
(12.7.1.1)
Luminaire with fluorescent lamp ≤ 70W
N/A
Test method 12.7.1.1 or Annex V ......................... :
Test according to 12.7.1.1:
N/A
- case of abnormal conditions
- Ballast failure at supply voltage (V) ................... :
- Components retained in place after the test
N/A
- Test with standard test finger after the test
N/A
Test according to Annex V:
N/A
- case of abnormal conditions
- measured winding temperature ( C): at 1,1 Un.. :
- measured temperature of fixing point/exposed
part ( C): at 1,1 Un................................................ :
- calculated temperature of fixing point/exposed
part ( C) ................................................................ :
4.12
(12.7.1.2)
Ball-pressure test:
N/A
- part tested; temperature ( C).............................. :
N/A
- part tested; temperature ( C).............................. :
N/A
Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA
N/A
- case of abnormal conditions
TRF No. IEC60598_2_4B
Page 21 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
- measured winding temperature ( C): at 1,1 Un.. :
- measured temperature of fixing point/exposed
part ( C): at 1,1 Un................................................ :
- calculated temperature of fixing point/exposed
part ( C) ................................................................ :
4.12
(12.7.1.3)
Ball-pressure test:
N/A
- part tested; temperature ( C).............................. :
N/A
- part tested; temperature ( C).............................. :
N/A
Luminaire with short circuit proof transformers ≤ 10 VA
N/A
- case of abnormal conditions
4.12 (12.7.2)
- Components retained in place after the test
N/A
- Test with standard test finger after the test
N/A
Luminaire with temperature sensing control
N/A
- thermal link
Yes
No
- manual reset cut-out
Yes
No
- auto reset cut-out
Yes
No
- case of abnormal conditions
- highest measured temperature of fixing
point/exposed part ( C): ........................................ :
Ball-pressure test:
N/A
- part tested; temperature ( C).............................. :
N/A
- part tested; temperature ( C).............................. :
N/A
4.12 (-)
Test overturned position (overturns < 15 )
N/A
4.13 (9)
RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE
P
4.13 (9.2)
Tests for ingress of dust, solid objects and moisture:
P
- classification according to IP .............................. : IP20
- mounting position during test ............................. : Attached to the electronic fan
as normal use
- fixing screws tightened; torque (Nm) .................. :
- tests according to clauses .................................. : Clause 9.2.0
- electric strength test afterwards
P
a) no deposit in dust-proof luminaire
N/A
b) no talcum in dust-tight luminaire
N/A
TRF No. IEC60598_2_4B
Page 22 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
c) no trace of water on current-carrying parts or
SELV parts or where it could become a hazard
N/A
d) i) For luminaires without drain holes – no water
entry
N/A
d) ii) For luminaires with drain holes – no
hazardous water entry
N/A
e) no water in watertight luminaire
N/A
f) no contact with live parts (IP 2X)
P
f) no entry into enclosure (IP 3X and IP 4X)
N/A
f) no contact with live parts (IP3X and IP4X)
N/A
g) no trace of water on part of lamp requiring
protection from splashing water
N/A
h) no damage of protective shield or glass
envelope
N/A
4.13 (9.3)
Humidity test 48 h
4.14 (10)
INSULATION RESISTANCE AND ELECTRIC STRENGTH
P
4.14 (10.2.1)
Insulation resistance test
P
93 % R.H.; 25 C
P
Cable or cord covered by metal foil or replaced by
a metal rod of mm Ø ............................................ :
Insulation resistance (M )
SELV:
P
- between current-carrying parts of different
> 100 M
polarity .................................................................. :
( 2M )
P
- between current-carrying parts and mounting
> 100 M
surface .................................................................. :
( 2M )
P
- between current-carrying parts and metal parts > 100 M
of the luminaire ..................................................... :
( 2M )
P
Other than SELV:
- between live parts of different polarity ................ : > 100 M
( 2M )
P
- between live parts and mounting surface ........... : > 100 M
( 4M )
P
- between live parts and metal parts..................... : > 100 M
( 4M )
P
- between live parts of different polarity through
action of a switch .................................................. :
4.14 (10.2.2)
P
Electric strength test
N/A
P
Dummy lamp
N/A
Luminaires with ignitors after 24 h test
N/A
Luminaires with manual ignitors
N/A
TRF No. IEC60598_2_4B
Page 23 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Test voltage (V):
P
SELV:
P
- between current-carrying parts of different
500 V
polarity .................................................................. :
P
- between current-carrying parts and mounting
500 V
surface .................................................................. :
P
- between current-carrying parts and metal parts 500 V
of the luminaire ..................................................... :
P
Other than SELV:
P
- between live parts of different polarity ................ : 1480 V
P
- between live parts and mounting surface ........... : 2960 V
P
- between live parts and metal parts..................... : 2960 V
P
- between live parts of different polarity through
action of a switch .................................................. :
N/A
4.14 (10.3)
Touch current (mA) ............................................... : 0,001 mA (< 0,7 mA)
P
4.15 (13)
RESISTANCE TO HEAT, FIRE AND TRACKING
P
4.15 (13.2.1)
Ball-pressure test:
P
- part tested; temperature ( C).............................. : Plastic material for enclosure,
base, Switch button; 125 C;
Ø 1,2 mm
P
- part tested; temperature ( C).............................. : Bobbin of transformer;
125 C; Ø1,2 mm
P
- part tested; temperature ( C).............................. : PCB; 125 C; Ø 0,8 mm
P
- part tested; temperature ( C).............................. : Holder for wire connector;
125 C; Ø 1,6 mm
P
- part tested; temperature ( C).............................. : Lamp cover; 75 C; Ø 1,3 mm
P
Needle flame test (10 s):
P
- part tested ........................................................... : Bobbin
P
4.15 (13.3.1)
- part tested ........................................................... : Holder for wire connector
4.15 (13.3.2)
4.15 (13.4.1)
N/A
Glow-wire test (650 C):
P
- part tested ........................................................... : Plastic material for enclosure,
base, switch button; PCB;
P
- part tested ........................................................... : Lamp cover
P
Tracking test: part tested ...................................... :
TRF No. IEC60598_2_4B
N/A
Page 24 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
ANNEX 1: components
object/part No.
EU plug
code manufacturer/
trademark
P
type/model
technical data
standard
mark(s) of
conformity
A
Dongguan
Changqi
Electronics
Co., Ltd
CQ-013
2,5 A, 250 V~
EN 50075
VDE
40015914
D
Zhongshan
QL-VA1
Xiaolan Qiangli
Electric Factory
Co., Ltd.
2,5 A, 250 V~
EN 50075
VDE
40013545
D
Interchangeable Interchangeabl 2,5 A, 250 V~
e
EN 50075
VDE
A
Shenzhen
Bao’an Xixiang
Changxiao
Electric
Manufacture
Factory
CWL668
13 A, 250 V~
BS1363-1
BSI
KM82901
D
Zhong Shan
Qiang Li
Electrical
Factory
Co., Ltd.
QL-340
13 A, 250 V~
BS1363-1
ASTA
LICENCE
NO. 735
D
Interchangeable Interchangeabl 13 A, 250 V~
e
BS1363-1
BSI
Appliance inlet
A
Zhejiang Bei Er
Jia Electronic
Co., Ltd.
ST-A03-002
ST-A03-005
2,5 A 250 V
EN 60320-1
VDE
40014833
Appliance
connector
A
Zhejiang Bei Er
Jia Electronic
Co., Ltd.
ST-A02
10 A 250 V
EN 60320-1
VDE
40007930
Supply cord
A
Dongguan
Changqi
Electronics
Co., Ltd
H03VVH2-F
H05VVH2-F
2 x 0,75 mm2
HD 21.5 S3
VDE
40011173
D
Zhongshan
H03VVH2-F
Xiaolan Qiangli H05VVH2-F
Electric Factory
Co., Ltd.
2 x 0,75 mm2
HD 21.5 S3
VDE
109832
D
Interchangeable H03VVH2-F
H05VVH2-F
2 x 0,75 mm2
HD 21.5 S3
VDE
UK plug
TRF No. IEC60598_2_4B
Page 25 of 43
Report No.:247910
IEC 60598-2-4
Clause
Transformer for
KN-2914HR
KN-2916HR
KN-2914
KN-2916
KN-2914H
KN-2916H
Requirement + Test
C
Kennede
Electronics
MFG. Co., Ltd.
Result - Remark
Verdict
EI57
I/P:
220-240 V~
50/60 Hz
O/P:
7,5 V~ 2,5 A
Class 130 (B)
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance
Component of the transformer
Bobbin
C
Chang Chun
Plastics Co Ltd
T375J
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E59481
C
Chang Chun
Plastics Co Ltd
4115 (a)
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E59481
C
E I DUPONT
DE NEMOURS
& CO INC
FR50(+)(f1)
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E41938
Thermal link
C
Aupo
Electronics Ltd.
A4
2 A 250 V~,
130 C
IEC/EN 60691
VDE
40008720
Transformer for
KN-2712
KN-2912
C
Kennede
Electronics
MFG. Co., Ltd.
EI48
I/P:
220-240 V~
50/60 Hz
O/P:
7,5 V~ 1,9 A
Class 130 (B)
IEC 60598-1
IEC 60598-2-4
Test in the
with
appliance
Components of transformer
-Bobbin
-Thermal link
C
Chang Chun
Plastics Co Ltd
T375J
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E59481
C
Chang Chun
Plastics Co Ltd
4115 (a)
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E59481
C
E I DUPONT
DE NEMOURS
& CO INC
FR50(+)(f1)
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E41938
A
Aupo
Electronics Ltd.
A4
2 A, 250 V~,
Tf 130 oC
IEC/EN 60691
Tested in the
appliance/
VDE
40008720
TRF No. IEC60598_2_4B
Page 26 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Transformer for
KN-2924
KN-2926
KN-2918H
KN-2926H
KN-2926HR
KN-2918HR
A
Kennede
Electronics
MFG. Co., Ltd.
Result - Remark
Verdict
EI57
I/P:
IEC 60598-1
220-240 V~
IEC 60598-2-4
50/60 Hz O/P:
12,5 V~ 1,5 A
Class 130 (B)
Test with
appliance
Components of transformer
-
C
Chang Chun
Plastics Co Ltd
T375J
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E59481
C
Chang Chun
Plastics Co Ltd
4115 (a)
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E59481
C
E I DUPONT
DE NEMOURS
& CO INC
FR50(+)(f1)
V-0
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance/
UL E41938
A
Aupo
Electronics Ltd.
A4
2 A, 250 V~,
Tf 130 oC
IEC/EN 60691
Tested in the
appliance/
VDE
40008720
C
Jiang Men Jia
Chuan Electric
& Cable
Co., Ltd.
1007
300 V~,
18-26 AWG,
80 oC
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance
UL E315723
C
Zhongshan
1007
Yong Roi
Electric Factory
Co., Ltd.
300 V~,
18-26 AWG,
80 oC
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance
UL E204893
C
Jiang Men Jia
1015
Chuan Electric
& Cable Co LTD
600 V~,
18-26 AWG,
105 oC
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance
UL E315723
C
Zhongshan
1015
Yong Roi
Electric Factory
Co., Ltd.
600 V~,
18-26 AWG,
105 oC
IEC 60598-1
IEC 60598-2-4
Tested in the
appliance
UL E204893
Plastic material
for enclosure,
base,
switch/control
button
C
Chi Mei
Corporation
ABS ,V-0
IEC 60598-1
Thickness of
IEC 60598-2-4
enclosure: 2,1
mm
Tested in
appliance
UL E56070
Heat shrinkable
tube for
KN-2903,
KN-2905
C
Shenzhen Woer RSFR-H
Heat-Shrinkable
Material
Co., Ltd.
600 V, 125 oC IEC 60598-1
IEC 60598-2-4
Tested in
appliance
UL E203950
-
Bobbin
Thermal link
Internal wiring
TRF No. IEC60598_2_4B
PA-764(+)
Page 27 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Dongguan
Salipt Co., Ltd.
Result - Remark
SALIPT
S-901-600
Verdict
600 V, 125 oC IEC 60598-1
IEC 60598-2-4
Tested in
appliance
UL E209436
Holder for wire
connector (except
for KN-2903)
C
Foshan Shunde CT-2
Kenda Electrical
Factory
3A
IEC 60598-1
IEC 60598-2-4
Tested in
appliance/
PCB
C
Jiang Men
Chang Ming
PCB Factory
CM-1
V-0
IEC 60598-1
IEC 60598-2-4
Tested in
appliance
UL E232206
Current fuse for
KN-2903 &
KN-2905
A
Shenzhen
Lanson
Electronics
Co. Ltd.
3K T1A250V
1 A, 250 V
EN 60127-1
EN 60127-3
VDE
40010682
D
Dongguan
334-Series(s)
Better Electronic
Technology
Co., Ltd.
1 A, 250 V
EN 60127-1
EN 60127-3
VDE
40025428
Switch for model
KN-2903
C
KEXIN
SS22F25G7
DC 50V 0,3A
IEC 60598-1
IEC 60598-2-4
Tested in
appliance
Switch for model
KN-2905
C
KEXIN
SS22F25G9
DC 50V 0,3A
IEC 60598-1
IEC 60598-2-4
Tested in
appliance
Switches for
models
KN-2926H,
KN-2918H,
KN-2926,
KN-2924,
KN-2916H,
KN-2914H,
KN-2916,
KN-2914
KN-2912
KN-2712
C
Heng Mei
Electronics
Co., Ltd.
SS43D015GB DC 50V 0,3A
5
IEC 60598-1
IEC 60598-2-4
Tested in
appliance
Battery for
KN-2926HR,
KN-2918HR,
KN-2926H,
KN-2918H,
KN-2926,
KN-2924
C
Chee Yuen
Plastic Product
(Huizhou)
Co., Ltd.
RB1245B
12V/4,5Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
C
Kennede
Electronics
MFG. Co., Ltd.
RB1245B
12V/4,5Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
TRF No. IEC60598_2_4B
Page 28 of 43
Report No.:247910
IEC 60598-2-4
Clause
Battery for
KN-2916HR,
KN-2914HR,
KN-2916H,
KN-2914H,
KN-2916,
KN-2914
Requirement + Test
Result - Remark
Verdict
C
Chee Yuen
Plastic Product
(Huizhou)
Co., Ltd.
RB670B
6V/7Ah Sealed IEC 60335-2-80
lead-acid
rechargeable
battery
Tested in
appliance
C
Kennede
Electronics
MFG. Co., Ltd.
RB670B
6V/7Ah Sealed IEC 60335-2-80
lead-acid
rechargeable
battery
Tested in
appliance
C
Chee Yuen
Plastic Product
(Huizhou)
Co., Ltd.
RB645B
6V/4,5Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
C
Kennede
Electronics
MFG. Co., Ltd.
RB645B
6V/4,5Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
C
Chee Yuen
Plastic Product
(Huizhou)
Co., Ltd.
RB416B
4V/1,6Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
C
Kennede
Electronics
MFG. Co., Ltd.
RB416B
4V/1,6Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
C
Chee Yuen
Plastic Product
(Huizhou)
Co., Ltd.
RB409B
4V/0,9Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
C
Kennede
Electronics
MFG. Co., Ltd.
RB409B
4V/0,9Ah
Sealed leadacid
rechargeable
battery
IEC 60335-2-80
Tested in
appliance
Weak part
(other fuse)
Zhongshan
Sanhe
Electronic
Co., Ltd.
2F
AC250V, 3A
IEC 60335-2-80
Tested in
appliance
Lamp cover
Chi Mei
Cooperation
PG-33
PS, HB
IEC 60598-1
IEC 60598-2-4
Tested in
appliance
UL E56070
Battery for
KN-2912,
KN-2712
Battery for
KN-2905
Battery for
KN-2903
TRF No. IEC60598_2_4B
Page 29 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
LED for
KN-2921,
KN-2914,
KN-2916,
KN-2924,
KN-2926,
KN-2914H,
KN-2916H,
KN-2918H,
KN-2926H
C
--
--
Exempt group
IEC 62471
Tested in
appliance
Refer to
EMTEK
report
ED14012212
5S
LED for
KN-2914HR,
KN-2916HR,
KN-2918HR,
KN-2926HR
C
--
--
Exempt group
IEC 62471
Tested in
appliance
Refer to
EMTEK
report
ED14012212
6S
LED for KN-2712
C
--
--
Exempt group
IEC 62471
Tested in
appliance
Refer to
EMTEK
report
ED14012212
7S
LED for
KN-2903,
KN-2905
C
--
--
Risk 1
IEC 62471
Tested in
appliance
Refer to
EMTEK
report
ED14012212
8S
The codes above have the following meaning:
A
- The component is replaceable with another one, also certified, with equivalent characteristics
B
- The component is replaceable if authorised by the test house
C
- Integrated component tested together with the appliance
D
- Alternative component
* Component has been certified by UL according to UL standards. Compliance with the requirements of the
product standard(s) has been checked.
TRF No. IEC60598_2_4B
Page 30 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
ANNEX 2: temperature measurements, thermal tests of Section 12
P
Type reference .....................................................: KN-2905
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 2,4
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
Pins of appliance inlet
50
70
42
Main PCB
60
130
43
Internal wire
51
80
43
Control board
43
Ref.
42
Battery
51
Ref.
45
Holder for wire connector
48
Ref.
44
Test corner
42
90
42
ta switch for lighting
50
Ref.
43
Heat shrinkable tube
44
125
43
LED lamp cover
46
75
42
TRF No. IEC60598_2_4B
limit
130
Page 31 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2903
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 1,8
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
Pins of appliance inlet
51
70
46
Main PCB
61
130
46
Internal wire
52
80
48
Control board
44
Ref.
48
Battery
44
Ref.
46
Test corner
42
90
45
ta switch for lighting
49
Ref.
44
Heat shrinkable tube
43
125
43
LED lamp cover
52
75
51
TRF No. IEC60598_2_4B
limit
130
Page 32 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2712
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 26,2
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
60
70
41
Pri-winding of transformer
100
130
41
175
Sec-winding of transformer
105
130
41
175
Main PCB
77
130
49
Internal wire
52
80
47
Control board
45
Ref.
43
Battery
46
Ref.
46
Test corner
46
90
46
ta switch for lighting
51
Ref.
43
Heat shrinkable tube
57
125
51
LED lamp cover
48
75
48
TRF No. IEC60598_2_4B
130
Page 33 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2926
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 34,6
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
55
70
41
Pri-winding of transformer
98
130
41
175
Sec-winding of transformer
99
130
42
175
Main PCB
113
130
76
Internal wire
72
80
71
Control board
46
Ref.
44
Battery
47
Ref.
47
Test corner
44
90
43
ta switch for lighting
58
Ref.
49
Heat shrinkable tube
62
125
58
LED lamp cover
47
75
46
TRF No. IEC60598_2_4B
130
Page 34 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2912
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 23,2
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
55
70
42
Pri-winding of transformer
90
130
42
175
Sec-winding of transformer
97
130
42
175
Main PCB
122
130
57
Internal wire
60
80
49
Control board
43
Ref.
44
Battery
58
Ref.
51
Test corner
47
90
42
ta switch for lighting
52
Ref.
45
Heat shrinkable tube
52
125
50
LED lamp cover
47
75
44
TRF No. IEC60598_2_4B
130
Page 35 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2916
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 26,3
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
61
70
46
Pri-winding of transformer
97
130
46
175
Sec-winding of transformer
99
130
46
175
Main PCB
110
130
60
Internal wire
67
80
57
Control board
51
Ref.
46
Battery
58
Ref.
46
Test corner
46
90
46
ta switch for lighting
56
Ref.
46
Heat shrinkable tube
54
125
52
LED lamp cover
52
75
48
TRF No. IEC60598_2_4B
130
Page 36 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2918HR
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 35,2
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
60
70
45
Pri-winding of transformer
97
130
46
175
Sec-winding of transformer
93
130
46
175
Main PCB
85
130
70
Internal wire
66
80
50
Control board
49
Ref.
46
Battery
58
Ref.
47
Test corner
46
90
42
ta switch for lighting
68
Ref.
57
Heat shrinkable tube
65
125
51
LED lamp cover
57
75
55
TRF No. IEC60598_2_4B
130
Page 37 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2926HR
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 34,8
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
41
70
41
Pri-winding of transformer
106
130
41
175
Sec-winding of transformer
106
130
42
175
Main PCB
95
130
76
Internal wire
64
80
71
Control board
45
Ref.
44
Battery
49
Ref.
47
Test corner
43
90
43
Heat shrinkable tube
72
125
58
LED lamp cover
48
75
46
TRF No. IEC60598_2_4B
130
Page 38 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2914HR
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 25,4
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
59
70
48
Pri-winding of transformer
89
130
48
175
Sec-winding of transformer
85
130
48
175
Main PCB
89
130
60
Internal wire
64
80
55
Control board
48
Ref.
47
Battery
52
Ref.
50
Test corner
46
90
45
Heat shrinkable tube
68
125
50
LED lamp cover
50
75
49
TRF No. IEC60598_2_4B
130
Page 39 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2918HR
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 36,8
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
56
70
45
Pri-winding of transformer
102
130
45
175
Sec-winding of transformer
101
130
45
175
Main PCB
85
130
55
Internal wire
65
80
46
Control board
49
Ref.
45
Battery
63
Ref.
47
Test corner
51
90
44
Heat shrinkable tube
60
125
48
LED lamp cover
52
75
48
TRF No. IEC60598_2_4B
130
Page 40 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
Type reference .....................................................: KN-2914H
Lamp used............................................................: Enclosed LED module
Lamp control gear used .......................................: Integral d.c. supplied
electronic circuit for LED
module
Mounting position of luminaire .............................: Attached to the electronic fan
Supply wattage (W) ..............................................: test 2: 26,5
Supply current (A) ................................................: test 2:
Calculated power factor .......................................:
P
Table: measured temperatures corrected for ta = 40 C:
- abnormal operating mode ..................................:
- test 1: rated voltage ...........................................:
1,06 x 240 V = 254,4 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................: (work on AC & charge mode)
- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:
Battery supplied (discharge
- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................: mode)
Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:
Clause 12.4 – normal
temperature ( C) of part
test 1
test 2
test 3
Clause 12.5 – abnormal
limit
test 4
limit
Pins of appliance inlet
59
70
46
Pri-winding of transformer
91
130
46
175
Sec-winding of transformer
89
130
46
175
Main PCB
103
130
56
Internal wire
70
80
51
Control board
50
Ref.
46
Battery
54
Ref.
46
Test corner
48
90
47
Heat shrinkable tube
66
125
48
LED lamp cover
51
75
47
TRF No. IEC60598_2_4B
130
Page 41 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
ANNEX 3: screw terminals (part of the luminaire)
N/A
(14)
SCREW TERMINALS
N/A
(14.2)
Type of terminal....................................................:
Rated current (A) ..................................................:
(14.3.2.1)
One or more conductors
N/A
(14.3.2.2)
Special preparation
N/A
(14.3.2.3)
Terminal size
N/A
Cross-sectional area (mm²)..................................:
N/A
(14.3.3)
Conductor space (mm) .........................................:
N/A
(14.4)
Mechanical tests
N/A
(14.4.1)
Minimum distance
N/A
(14.4.2)
Cannot slip out
N/A
(14.4.3)
Special preparation
N/A
(14.4.4)
Nominal diameter of thread (metric ISO thread) ..: M
N/A
External wiring
N/A
No soft metal
N/A
(14.4.5)
Corrosion
N/A
(14.4.6)
Nominal diameter of thread (mm) ........................:
N/A
Torque (Nm) .........................................................:
N/A
Between metal surfaces
N/A
Lug terminal
N/A
Mantle terminal
N/A
Pull test; pull (N) ...................................................:
N/A
Without undue damage
N/A
(14.4.7)
(14.4.8)
TRF No. IEC60598_2_4B
Page 42 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Verdict
ANNEX 4: screwless terminals (part of the luminaire)
N/A
(15)
SCREWLESS TERMINALS
N/A
(15.2)
Type of terminal....................................................:
Rated current (A) ..................................................:
(15.3.1)
Material
N/A
(15.3.2)
Clamping
N/A
(15.3.3)
Stop
N/A
(15.3.4)
Unprepared conductors
N/A
(15.3.5)
Pressure on insulating material
N/A
(15.3.6)
Clear connection method
N/A
(15.3.7)
Clamping independently
N/A
(15.3.8)
Fixed in position
N/A
(15.3.10)
Conductor size
N/A
Type of conductor
N/A
(15.5.1)
Terminals internal wiring
N/A
(15.5.1.1)
Pull test spring-type terminals (4 N,
4 samples) .:
N/A
(15.5.1.2)
Pull test pin or tab terminals (4 N,
4 samples)
:
N/A
Insertion force not exceeding 50 N
N/A
(15.5.2)
Permanent connections: pull-off test (20 N)
N/A
(15.6)
Electrical tests
N/A
Voltage drop (mV) after 1 h (4 samples) ..............:
N/A
Voltage drop of two inseparable joints
N/A
Number of cycles..................................................:
(15.7)
Voltage drop (mV) after 10th alt. 25th cycle
(4 samples)...........................................................:
N/A
Voltage drop (mV) after 50th alt. 100th cycle
(4 samples)...........................................................:
N/A
After ageing, voltage drop (mV) after 10th alt.
25th cycle (4 samples) .........................................:
N/A
After ageing, voltage drop (mV) after 50th alt.
100th cycle (4 samples) .......................................:
N/A
Terminals external wiring
N/A
Terminal size and rating
N/A
TRF No. IEC60598_2_4B
Page 43 of 43
Report No.:247910
IEC 60598-2-4
Clause
Requirement + Test
(15.8.1)
Pull test spring-type terminals or welded
connections (4 samples); pull (N) ........................:
N/A
Pull test pin or tab terminals (4 samples);
pull (N) .................................................................:
N/A
Contact resistance test
N/A
Voltage drop (mV) after 1 h
N/A
(15.9)
terminal
1
2
Result - Remark
3
4
5
6
7
Verdict
8
9
10
voltage drop (mV)
Voltage drop of two inseparable joints
N/A
Voltage drop after 10th alt. 25th cycle
N/A
Max. allowed voltage drop (mV) ................ :
terminal
1
2
3
4
5
6
7
8
9
10
voltage drop (mV)
Voltage drop after 50th alt. 100th cycle
N/A
Max. allowed voltage drop (mV) ................ :
terminal
1
2
3
4
5
6
7
8
9
10
voltage drop (mV)
Continued ageing: voltage drop after 10th alt. 25th cycle
N/A
Max. allowed voltage drop (mV) ................ :
terminal
1
2
3
4
5
6
7
8
9
10
voltage drop (mV)
Continued ageing: voltage drop after 50th alt. 100th cycle
N/A
Max. allowed voltage drop (mV) ................ :
terminal
voltage drop (mV)
TRF No. IEC60598_2_4B
1
2
3
4
5
6
7
8
9
10
Page 1 of 2
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
Attachment 1: European Group Differences and National Differences
P
ATTACHMENT TO TEST REPORT IEC 60598-2-4
EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
Luminaires
Part 2: Particular requirements:
Section Four – Portable general purpose luminaires
Differences according .................... : EN 60598-2-4:1997 used in conjunction with
EN 60598-1:2008 + A11:2009
Annex Form No. .............................. : EU_GD_IEC_60598_2_4A
Annex Form Originator ..................... : IMQ S.p.A.
Master Annex Form .......................... : 2009-09
Copyright © 2009 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
CENELEC COMMON MODIFICATIONS (EN)
P
4.5 (3)
MARKING
P
4.5 (3.3.101)
Adequate warning on the package
4.6 (4)
CONSTRUCTION
4.6 (4.11.6)
Electro-mechanical contact systems
4.10 (5)
EXTERNAL AND INTERNAL WIRING
4.10 (5.2.1)
Connecting leads
N/A
- without a means for connection to the supply
N/A
- terminal block specified
N/A
- relevant information provided
N/A
- compliance with 4.6, 4.7.1, 4.7.2, 4.10.1, 11.2,
12 and 13.2 of Part 1
N/A
N/A
P
N/A
P
4.10 (5.2.2)
Cables equal to HD21 S2 or HD22 S2
P
4.12 (12)
ENDURANCE TEST AND THERMAL TEST
P
4.12 (12.4.2c) Thermal test (normal operation)
TRF No. IEC60598_2_4B_ATTACHMENT
N/A
Page 2 of 2
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
ZB
ANNEX ZB, SPECIAL NATIONAL CONDITIONS (EN)
(3.3)
DK: power supply cord with label
N/A
IT: warning label on Class 0 luminaire
N/A
(4.5.1)
DK: socket-outlets
N/A
(5.2.1)
CY, DK, FI, SE, GB: type of plug
ZC
ANNEX ZC, NATIONAL DEVIATIONS (EN)
N/A
(4 & 5)
FR: Shuttered socket-outlets 10/16A
N/A
(13.3)
FR: Glow-wire test 850 C alt. 750 C for
luminaires in premises open to public or 960°C
for luminaires in emergency exits
N/A
(13.3)
GB: Requirements according to United Kingdom
Building Regulation
N/A
TRF No. IEC60598_2_4B_ATTACHMENT
Result - Remark
GB plug
Verdict
P
P
Page 1 of 7
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
Attachment 2: Addition test according to IEC 62031:2008+A1:2012
P
4
GENERAL REQUIREMENTS
P
4.4
Integral modules treated as part of luminaires
defined in clause 0.5 of IEC 60598-1
Yes
4.5
Independent modules complies with
requirements in IEC 60598-1
No
5
GENERAL TEST REQUIREMENTS
P
5.5
SELV-operated LED modules comply with Annex (see Annex B)
I of IEC 61347-2-13
P
6
CLASSIFICATION
P
Built-in module .....................................................: Yes
No
Independent module ............................................: Yes
No
Integral module ....................................................: Yes
No
For Integral module; Note to 1.2.1 in IEC 60598-1
applies.
P
7
MARKING
N/A
7.1
Mandatory markings:
N/A
- mark of origin
N/A
- model number, type reference ..........................:
N/A
- rated supply voltage (V) ....................................:
N/A
- rated supply current (A) ....................................:
N/A
- rated input power (V) ........................................:
N/A
- nominal power
N/A
- indication of connections, wiring diagram
N/A
- value of tc
N/A
- eye protection
N/A
- marking of built-in modules only
N/A
7.2
- location of marking
N/A
7.3
Marking durable and legible
N/A
Rubbing 15 s water, marking legible
N/A
SCREW TERMINALS
N/A
8
TRF No. IEC60598_2_4B_ATTACHMENT
Page 2 of 7
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
Compliance with section 14 of IEC 60598-1
N/A
SCREWLESS TERMINALS
N/A
Compliance with section 15 of IEC 60598-1
N/A
CONNECTORS
N/A
Compliance with IEC 60838-2-2
N/A
PROVISION FOR PROTECTIVE EARTHING
N/A
External metal parts connected to the earth terminal:
N/A
- compliance with 7.2.1 in IEC 60598-1
N/A
Test with a current of 10 A between earthing
terminal and each of the accessible metal parts;
measured resistance ( ): < 0,5 .......................:
N/A
Protective earth, symbol
N/A
Terminal complying with clause 8 in Part 1
N/A
Locked against loosening and not possible to
loosen by hand
N/A
Not possible to loosen clamping means
unintentionally on screwless terminals
N/A
Earthing via means of fixing
N/A
Earthing terminal only used for the earthing of the
control gear
N/A
All parts of material minimizing the danger of
electrolytic corrosion
N/A
Made of brass or equivalent material
N/A
Contact surface bare metal
N/A
Conductors by tracks on printed circuit boards:
N/A
- a.c. current of 25 A for 1 min between earthing
terminal and accessible metal parts
N/A
- compliance with clause 7.2.1 in IEC 60598-1
N/A
PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS
N/A
Protection against accidental contact with live parts in compliance with IEC 61347-1
(clause numbers between parentheses refer to IEC 61347-1)
N/A
- (10.1)
Controlgear protected against accidental contact
with live parts
N/A
- (A1)
Current measured according to IEC 60990, figure
N/A
9
8 (10)
TRF No. IEC60598_2_4B_ATTACHMENT
Page 3 of 7
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
4 and clause 7.1: max. 0,7 mA (peak) or 2,0 mA
d.c., for f 1000 Hz max. 70 mA ........................:
- (A2)
Voltage at 50 k
(V): max. 34 V (peak) ..............:
N/A
Lacquer or enamel not used for protection or
insulation
N/A
Adequate mechanical strength on parts providing
protection
N/A
- (10.2)
Capacitors > 0,5 F: voltage after 1 min (V): <
50 V .....................................................................:
N/A
8.1 (-)
SELV-equivalent controlgear accessible parts are
insulated from live parts by double or reinforced
insulation according 8.6 and 13.1 in IEC 60065
N/A
8.2 (-)
Exposed terminals of SELV or SELV-equivalent
controlgear are allowed if:
- the rated or maximum output voltage does not
exceeding 25 V r.m.s.
- the no-load output voltage does not exceed 30
V r.m.s. or 33 √2 V peak
N/A
Insulated terminals if rated output voltage >25 V
N/A
One capacitor Y1 or two capacitors Y2 of the
same values used in series between SELV or
SELV-equivalent output and primary circuits
- Capacitor complying with IEC 60384-14
- Other components bridging the separating
transformer complying with EN 60065, clause 14
N/A
11
12
MOISTURE RESISTANCE AND INSULATION
P
Protection against moisture and insulation in compliance with Clause 11,
IEC 61347-1
P
After storage 48 h at 91-95% relative humidity
> 100 M
and 20-30 C measuring of insulation resistance
with d.c. 500 V (M ): 2 M ..............................:
P
Adequate insulation between input and output
terminals not bounded together in SELVequivalent controlgear
N/A
For double or reinforced insulation the resistance
exceeds 4 M
N/A
ELECTRIC STRENGTH
P
Electric strength in compliance with Clause 12 of IEC 61347-1
P
Immediately after clause 11 electric strength test for 1 min
P
Working voltage
P
42 V, test voltage 500 V
TRF No. IEC60598_2_4B_ATTACHMENT
Page 4 of 7
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
Working voltage > 42 V, test voltage (V):
2U + 1000 V ........................................................:
N/A
Reinforced insulation, test voltage (V): ..............:
N/A
P
No flashover or breakdown
N/A
Windings in separating transformers in SELVequivalent control gear according to 14.3.2 of
EN 60065
13
FAULT CONDITIONS
P
13.1
In compliance with IEC 61347-1 (clause numbers between parentheses refer to
IEC 61347-1)
P
When operated under fault conditions the LED-module:
-
- does not emit flames or molten material
P
- does not produce flammable gases
P
- (14.1)
- protection against accidental contact not
impaired
N/A
Thermally protected controlgear does not exceed
the marked temperature value
N/A
Fault conditions: capacitors, resistors or inductors
without proof of compliance with relevant
specifications have been short-circuited or
disconnected
N/A
Short-circuit of creepage distances and
clearances if less than specified in clause 16 in
Part 1 (except between live parts and accessible
metal parts)
N/A
Distances on printed boards provided with
coating according to IEC 60664-3
N/A
- (14.2)
Short-circuit or interruption of semiconductor
devices
- (14.3)
Short-circuit across insulation consisting of
lacquer, enamel or textile
N/A
- (14.4)
Short-circuit across electrolytic capacitors
N/A
- (14.5)
During the tests, a five-layer tissue paper, where
the test specimen is wrapped, does not ignite
N/A
After the tests the insulation resistance with d.c.
500 V (M ) are 1 M .......................................:
N/A
Temperature declared thermally protected LEDmodules fulfil the requirements in Annex C of IEC
61437-1
N/A
13.2
Module withstands overpower condition >15 min.
TRF No. IEC60598_2_4B_ATTACHMENT
(see appended table)
1,5 times rated wattage of
LED module
N/A
P
Page 5 of 7
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
N/A
Module with automatic protective device or power
limiter, test performed 15 min. at limit.
15
16
During the tests, tissue paper, spread below
module, does not ignite
P
CONSTRUCTION
P
Wood, cotton, silk, paper and similar fibrous
material not used as insulation
P
CREEPAGE DISTANCES AND CLEARANCES
P
Creepage and distances and clearances in compliance with IEC 60598-1
P
Class of protection ....................................... :
III
—
Working voltage (V) ..................................... :
<25 V r.m.s.
—
Voltage form ................................................. :
Non-sinusoidal
—
PTI ................................................................ :
< 600
—
Rated pulse voltage (kV) ............................. :
17 (17)
Verdict
—
(1) Live parts of different polarity: cr (mm); cl (mm)
....................................................................... :
N/A
(2) Live parts and accessible parts: cr (mm); cl
(mm) ............................................................. :
N/A
(3) Parts becoming live: cr (mm); cl (mm) ... :
N/A
(4) Outer surface of cable: cr (mm); cl (mm) :
N/A
(5) Live parts of switches: cr (mm); cl (mm) :
N/A
(6) Live parts and supporting surface: cr (mm); cl
(mm) ............................................................. :
N/A
SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS
P
Screws, current-carrying parts and connections in compliance with IEC 60598-1
(clause numbers between parentheses refer to IEC 60598-1)
P
(4.11)
Electrical connections:
P
(4.11.1)
Contact pressure
N/A
(4.11.2)
Screws:
N/A
- self-tapping screws
N/A
- thread-cutting screws
N/A
- at least two self-tapping screws
N/A
Screw locking:
N/A
- spring washer
N/A
(4.11.3)
TRF No. IEC60598_2_4B_ATTACHMENT
Page 6 of 7
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
N/A
- rivets
(4.11.4)
Material of current-carrying parts
P
(4.11.5)
No contact to wood
P
(4.12)
Mechanical connections and glands:
N/A
(4.12.1)
Mechanical stress
N/A
Screws not made of soft metal
N/A
Screws of insulating material
N/A
Torque test: part; torque (Nm) .............................:
N/A
Torque test: part; torque (Nm) .............................:
N/A
Torque test: part; torque (Nm) .............................:
N/A
(4.12.2)
Screw diameter < 3 mm screwed into metal
N/A
(4.12.3)
Void
(4.12.4)
Locked connections
N/A
(4.12.5)
Screwed glands: force (N) ...................................:
N/A
18 (18)
RESISTANCE TO HEAT, FIRE AND TRACKING
P
Resistance to Heat, Fire and Tracking in compliance with IEC 61347-1 (clause
numbers between parentheses refer to IEC 61347-1)
P
Parts of insulating material retaining live parts in position, ball-pressure test:
P
- part; test temperature ( C) ................................: See main report 60598-2-4
part
P
(18.1)
N/A
- part; test temperature ( C) ................................:
(18.2)
Printed boards in accordance with IEC 60249-1,
4.3
See main report 60598-2-4
part
P
(18.3)
External parts of insulating material preventing
electric shock glow-wire test 650 C
See main report 60598-2-4
part
P
(18.4)
Parts of insulating material retaining live parts in position, needle-flame test 10 s:
- flame extinguished within 30 s
See main report 60598-2-4
part
- no flaming drops igniting tissue paper
P
P
P
(18.5)
Tracking test
N/A
19
RESISTANCE TO CORROSION
N/A
Resistance to corrosion in compliance with IEC 61347-1
N/A
Rust protection:
N/A
- test according 4.18.1 of IEC 60598-1
N/A
TRF No. IEC60598_2_4B_ATTACHMENT
Page 7 of 7
Report No.:247910
IEC 60598-2-4_ATTACHMENT
Clause
Requirement + Test
Result - Remark
- adequate varnish on the outer surface
A
B
Verdict
N/A
ANNEX A - TESTS
P
All tests performed in accordance with the advise
given in Annex H of IEC 61347-1, if applicable
P
ANNEX B - SELV-operated LED modules
P
ANNEX I of IEC 61347-2-13 - PARTICULAR ADDITIONAL REQUIREMENTS FOR
INDEPENDENT SELV D.C. OR A.C. SUPPLIED ELECTRONIC STEP-DOWN
CONVERTORS FOR FILAMENT LAMPS
TRF No. IEC60598_2_4B_ATTACHMENT
N/A
Page 1 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Attachment 3: Pictures
Verdict
P
Overview of model KN-2926
Internal view of model KN-2926
TRF No. IEC60598_2_4B_ATTACHMENT
Page 2 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Appliance inlet
DC inlet on the control panel
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 3 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Control panel of model KN-2926
LED module
Front control PCB of model KN-2926
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 4 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Back control PCB of model KN-2926
Front power PCB of model KN-2926
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 5 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Back power PCB of model KN-2926
Overview of transformer on model KN-2926
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 6 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of transformer on model KN-2926
Internal view of transformer on model KN-2926
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 7 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Thermal fuse on transformer on model KN-2926
LED module
Overview of model KN-2712
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 8 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Control panel of model KN-2712
Internal view of model KN-2712
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 9 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Internal view of model KN-2712
Front power PCB of model KN-2712
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 10 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Back power PCB of model KN-2712
Overview of transformer on model KN-2712
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 11 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Internal view of transformer on model KN-2712
Internal view of transformer (bobbin) on model KN-2712
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 12 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Thermal fuse on transformer on model KN-2712
Overview of model KN-2918HR
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 13 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Internal view of model KN-2918HR
Internal view of model KN-2918HR
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 14 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Control panel of model KN-2918HR
LED
module
Front power PCB of model KN-2918HR
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 15 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Front power PCB of model KN-2918HR
Overview of transformer on model KN-2918HR
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 16 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of transformer on model KN-2918HR
Internal view of transformer (bobbin) on model 2918HR
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 17 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Thermal fuse on transformer on model 2918HR
Overview of model KN-2905
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 18 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Internal view of model KN-2905
Internal view of model KN-2905
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 19 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Control panel of model KN-2905
Front Commutator PCB on model KN-2905
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 20 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Back commutator PCB on model KN-2905
Front overview of LED lamp PCB1 on model KN-2905
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
P
Page 21 of 28
Report No.: 24
47910
IEC 60598-2--4
Clause
Require
ement + Test
Resu
ult - Remark
Back overview of LE
ED lamp PCB
B1 on model KN-2905
Front ove
erview of LE D lamp PCB
B2 on model KN-2905
TRF No. IEC
C60598_2_4
4B_ATTACH
HMENT
Verdict
P
Page 22 of 28
Report No.: 24
47910
IEC 60598-2--4
Clause
Require
ement + Test
Resu
ult - Remark
Back overrview of LED
D lamp PCB2 on model KN-2905
Overvie
ew of model KN-2903
K
TRF No. IEC
C60598_2_4
4B_ATTACH
HMENT
Verdict
Page 23 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of model KN-2912
Overview of model KN-2914
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 24 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of model KN-2916
Overview of model KN-2924
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 25 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of model KN-2914H
Overview of model KN-2916H
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 26 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of model KN-2918H
Overview of model KN-2926H
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 27 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of model KN-2914HR
Overview of model KN-2916HR
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Page 28 of 28
Report No.: 247910
IEC 60598-2-4
Clause
Requirement + Test
Result - Remark
Overview of model KN-2926HR
End of report
TRF No. IEC60598_2_4B_ATTACHMENT
Verdict
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement