VAG Airbag Reseter User`s manual
VAG Airbag Reseter User’s manual
1. FUNCTIONS
·Data fault repair of Audi/VW/Opel airbag modules
·Crash data reset of Audi/VW/Opel airbag modules
2. HARDWARE
Fig 1. Main hardware and PCB
·Yellow -Button is used to repair data fault
·Red -Button is used to reset crash data
·Led-Indicators are used to indicate the operating state, while the
red led indicate ‘power on’, the green led indicate ‘busy’ and
‘error’, and the yellow led indicate ‘usb port connected’.
·OBD cable is used to connect the tool to the diagnosis socket of the car.
·USB cable is used to connect the tool to the computer for firmware
updating.
·Power-Connector is used to supply 12V-DC to the tool. (center of the
connecter is power +)
·Adapter-Connector is not used at present.
3. HOW TO USE
·Data Fault Repair: connect the airbag reseter and the car’s diagnosis
socket by the OBD cable, the red led light up, push the yellow button,
the green led light up, and for a while the green led black out, this
means the data fault has been repaired successfully. ( if the green
led becomes flashing, that mean the communication between the
tool and the car failed, or data fault repair failed, check the
connection and repeat the above procedure.)
·Crash Data Reset: connect the airbag reseter and the car’s diagnosis
socket by the OBD cable, the red led light up, push the red button, the
green led light up, and for a while the green led black out, this means the
crash data has been reset successfully. ( if the green becomes flashing,
this mean the communication between the tool and the car failed, or
crash data reset failed, check the connection and repeat the above
procedure.)
4. Tested Airbag Modules
4.1 VW series
VW3: 1GD 909 603 A
Fig 2. VW3
VW5: 1C0 909 601 / 1C0 909 601 A / 1GD 909 601 / 1GD
909 601 A / 6Q0 909 605 / 6Q0 909 605 A
Fig 3. VW5
VW6: 6Q0 909 605 C
Fig 4. VW6
4.2 AUDI series
4B0 959 655G / 4B0 959 655H / 4B0 959 655E / 4B0 959 655F / 4B0 959
655R / 4B0 959 655J(50Pin)
Fig 5. AUDI(84Pin)
Fig 6. AUDI(50Pin)
4.3 OPEL (GM) series
GM 09 229 302
Fig 7. GM 09 229 302
GM 05 490 636
Fig 8. GM 09 229 302
GM 90 569 350
Fig 10. GM 90 569 350
GM 92 099 726
Fig 11. GM 92 099 726
GM 90 562 544
Fig 12. GM 90 562 544
5. Software Update
·Setup Usb Driver: connect the airbag reseter to PC by the
usb cable, and plug 12-V DC regulator to the Power
Connector.
·Run the Update programs presented by SMELECOM, when “Firmware
Update Finished” appears in the screen, that means the update operation
is successfully finished.
6.Others
·Connect the tool to PC by the usb cable only when updateing the firmware.
Other times you must disconnect the tool to the PC , it is very important.
If you have airbags that we did not test, please send it to us, we will send it
back to you after testing, we will pay all the post cost.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement