EV W1012(E) 网站版
EV LIGHT
R
EV W1012
USER MANUAL
Please read it carefully
INDEX
1.SAFETY GUIDELINE .......................................................................................... - 2 2.TECHNICAL PARAMETER .................................................................................. - 3 3.LIGHTING INSTALLATION .................................................................................. - 4 4.POWER SUPPLY-CONTROL SIGNAL CONNECTIONS ............................................ - 4 5.OPERATION MENU .......................................................................................... - 5 5.1 BUTTON OPERATION ........................................................................................ - 7 5.2 DMX ADDRESS CODE SETTING .......................................................................... - 7 5.3 STATIC SETTING ................................................................................................ - 7 5.4 COLOR CAST CALIBRATION SETTING .................................................................. - 7 -
5.5 CHANNEL MODE SETTING ................................................................................ - 7 5.6 DIMMING MODE SETTING ................................................................................ - 7 -
5.7 DISPLAY SETTING .............................................................................................. -7 5.8 RUNNING THE AUTO-RUN,AUTO-PROGRAMMING PROGRAM ............................ -7 5.9 EDITTING THE AUTO-PROGRAMMING PROGRAM .............................................. -8 5.10 LIGHTING INFORMATION VIEW ...................................................................... - 8 5.11 LIGHTING SETTING PARAMETER RESET ........................................................... - 8 5.12【PROG】AUTO-PROGRAMMING PARAMETER RESET ...................................... -8 5.13 LIGHTING RESET .............................................................................................. -8 5.14 LIGHTING PARAMETER DOWNLOADING EACH OTHER ..................................... - 8 6. DMX PROTOCOL
..........................................................................................- 9 -
7. MAINTENANCE
.......................................................................................... -11-
8. TROUBLESHOOTING
................................................................................... -11-
ACCESSORIES
These items are packed together with the Lighting,please check:
Name
Quantity
Unit
This manual
1
Pc
Safety cord
2
Pc
Power cable
1
Pc
hanging device
1
set
Remark
1、SAFETY GUIDELINE
 Please keep this manual for further inquire reference. Please make sure they also have this
user manual if you sell this Lighting to other users. Each unit is packed properly by the
manufacturer. Please operate this Lighting according to the user manual. Any damage caused
by improper use will not be assumed by the manufacturer.
 When receiving the lighting ,please dispose the carton, check and inspect there is any
damage or not. Should there be any damage caused by transportation,do not use the lighting
and consult your dealer or the manufacturer.

This lighting can be used indoors and outdoors, IP65.

The lighting is only intended for installation and operation by qualified personnel.

Do not mount the lighting directly onto inflammable surface.

Ensure power supply voltage correspond to device requirements before running.
 It is essential that each lighting is correctly earthed and that electrical installation conforms
to all relevant standards.
 When the lighting is hanged to a high place, please use a safety cord provided to pass
through the lighting handles as a secondary safety fixing for safety seasons. For details, refer to
“LIGHTING INSTALLATION” section.
 Avoid direct exposure to the light from the lamp(specially for people with epilepsy). The light
is harmful to eyes.
 Do not project the beam onto inflammable surfaces. The minimum distance between the
lighting and irradiated object should be 2 m.
 Exterior surface temperature of the lighting will be 65℃ when working,please do not touch
it with bare hands .
 To prevent electric shocking, please do not touch the power cord when the lighting is
running.

Never let the power cord mix with other cables.

The LED lens should be changed if deeply scratched or cracked.
 There is no user serviceable parts inside the lighting. Before using the device, please check
whether the covers or housing are well installed or not, and whether the screws are installed firmly
or not. Do not open the housing and never operate the lighting with the covers removed.
 Always disconnect a lighting from the power supply when the device is not in use or
before cleaning it or before attempting any maintenance work!

Electrical connection must only be carried out by qualified personnel.

Please use the original packing material for second transportation.
 If you have any questions or suggestions, please do not hesitate to consult your
dealer or our factory.
-2-
2、TECHNICAL PARAMETER
Input Voltage: AC100V-AC240V, 50/60HZ;
Power Consumption: 120W ;
Lamp Specifications:12 pcs four in one(RGBW) high-efficiency 10W LED, rated life 50000
hours;
Lens Angle:25º(Optional:45°)
;
Spot Angle:40º;
Color:RGBW linear color mixing;
Color Temperature:color cast calibration setting、color temperature output inside device;
Dimmer: 0-100% linearly dimming, 5 types dimmer modes,smooth dimming, flicker-free;
Shutter:independent electronic strobe;
Control Mode:
Standard DMX512,3 pin interfaces;
4 channel modes;
Master/slave mode,no need to set up the master and slave manually, will receive the main
engine data automatically;
33 auto-running modes,rainbow channel and rainbow effect;
Other Functions:
Self-programming function, 3 chases,each chase has 20 scenes,fade function;
Lighting setting data、self-programming data can be downloaded each other;
Temperature Control Protection:Both of lamp holder and base have temperature control
protection;
Waterproof Grade: IP65;
Work Environment Temperature: -20°C~40°C;
Net Weight:5.6 Kg;
DIMENSION
-3-
3、
LIGHTING INSTALLATION
MOUNTING HOLE FOR LAMP HOOK
SAFETY RING
THE SCREW HOLE
PICTURE TWO
PICTURE ONE
 The lighting can be hanged on the high place with using the lamp hooks (as showed in
picture 1). Use the safety cord provided to pass through the bottom safe ring and
hang it as a second safety fixing.
 The lighting also can place on the ground and make sure balance stand ,as showed in
picture 2.
Note:
 Ensure
support loading ability at least 10 times more than product weight,and make
sure lighting be firmly installed.
 The
lighting must be installed by the qualified personnel. Please install it at the
place where no one goes through.
4、
POWER SUPPLY-CONTROL SIGNAL CONNECTIONS

Make the XLR signal line connect with the lighting, one port connects with the output port of
lighting, another one connects with the input port of another lighting.

Due to the output and input of the lighting keep connecting all the time, so the DMX circuit
still can be keep connecting when the power of certain unit occurs turn-off.

XLR signal line only can be used in series connection pattern(the amount of the lighting can
not be more than 32 PCS), not available in parallel connection pattern. Must add a signal
amplifier if the length of signal line exceeds 60M between controller and lighting or between
two lightings.

In the controller mode, at the last fixture in the chain, the DMX output
has to be connected with a DMX terminator. The DMX terminator is
simply a connector with a resistor about 120Ω(OHM)connected
across pins 2 and 3 of the Canon plug(please see the picture
in the right).It can prevent the noise and reflection caused by DMX
512 signal during transmission.
-4-

The transmission speed of DMX 512 signal is very quick. It will affect the signal transmission if
any damage of the signal line, the weld is not firm or bad connection etc

The connector with 3 pins XLR is more universal than the one with 5 pins XLR.
3 pins XLR:PIN 1:GND,PIN 2:- signal,PIN 3:+ signal.
5 pins XLR:PIN 1:GND,PIN 2:- signal,PIN 3:+ signal,PIN4/PIN5:UNUSED.
There can’t be more than 12 PCS of lightings for series connection pattern when using 220V
AC; it can’t exceed 6 PCS lightings for series connection pattern when using 110V AC.

POWER OUT
DMX OUT
POWER IN
5、
Tab
TO TERMINATOR
DMX CONSOLE
OPERATION MENU
Level 1
ADDR(Address)
001-512
STAT(Static control) R1
G1
B1
W1
R2
G2
B2
W2
R3
G3
B3
W3
SHUT
SET(Set)
CAL(Calibration)
CH(Channel mode)
D(Dimming mode)
DISY(Display set)
Level 2
Level 3
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
0-255 *
R(Red)
G(Green)
B(Blue)
W(White)
USE
18CH
10CH
7CH
5CH
2CH
OFF
D1
D2
D3
D4
ON(Permanent on)
2 OF (2 minutes
off)
0-255
0-255
0-255
0-255
YES/NO
-5-
Level 4
CTST(Color
temperature set)
AUTO(Auto)
PROG(Program)
INFO(Information)
LOAD(Load)
REST(Reset)
SEND(Send)
CT01
R(Red)
0-255
.
.
.
CT10
AT01
.
.
.
AT33
ATSP(Auto speed)
CHS1(Chase 1)
CHS2(Chase 2)
CHS3(Chase 3)
CHS1(Chase 1)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
CHS3(Chase 3)
SOFT(Software
version)
LEDs
G(Green)
B(Blue)
W(White)
0-255
0-255
0-255
RUN.. *
RUN.. *
RUN.. *
RUN.. *
RUN.. *
0-255(S)
RUN.. *
RUN.. *
RUN.. *
SC01(Scene 1)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
SC25(Scene 25)
R1
G1
B1
W1
R2
G2
B2
W2
R3
G3
B3
W3
SHUT
AUTO
ATSP
TIME
WAIT
USE
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
NONE,AT01-AT33
0-255(S)
0-255(S)
0-25.5(S)
YES/NO
Vx.x
xxR
xxG
xxB
xxW
POW(Power reduction) 100%/80%/50%
ST L(Setting load) YES/NO
PR L(Program load) YES/NO
YES/NO
YES/NO
Illustrations:
When the menu is set as the information of * position, the
projector will be set automatically to be the main engine and then
send data to external. Other projectors can receive these data and run
synchronously with the main engine. It still be run according to these
setting parameter even if power reconnection after power off .
When setting YES in【ST L】menu, The parameter will bereset to be
the factory default value as which with underline of above chart.
-6-
5.1
1)
2)
3)
4)
5.2
BUTTON OPERATION
MENU:To return to the previous menu.
ENTER:Enter to the next menu or save.
UP:Menu selection or increasing the parameter.
DOWN:Menu selection or decreasing the parameter.
DMX ADDRESS CODE SETTING
1) Press the 【ENTER】 button in 【ADDR】 menu, then enter to the DMX address code setting.
2) Press the【UP/DOWN】button to select【1-512】numerical value.
3) Press the【ENTER】button to escape and save.
5.3
STATIC SETTING
1) Press the【ENTER】button in 【STAT】menu, then enter to the static setting.
2) Press the【UP/DOWN】 button to select 【RED1】
,
【GREEN1】…… 【WHITE3】and【SHUT】.
3) Press the【UP/DOWN】button to set up the【0-255】numerical value.
4) Press the【ENTER】button to escape and save.
5.4
COLOR CAST CALIBRATION SETTING
1) Press the【ENTER】button in 【CAL】menu, then enter to the color cast calibration setting.
2) Press the【UP/DOWN】button to select 【RED】
,
【GREEN】
,
【BLUE】,
【WHITE】
3) Press the【UP/DOWN】button to set up the【0-255】numerical value.
4) On the【USE】interface, pressing【ON】button means valid, otherwise【OFF】button invalid.
5) Press the【ENTER】button to escape and save.
Illustrations: When pressing the【ON】button which means valid on the【USE】
interface, the actual output value of RED,GREEN,BLUE,WHITE is output in
accordance with the percentage which the color cast calibration value divides 255.
5.5
CHANNEL MODE SETTING
1) Press the【ENTER】button in 【CHMD】menu, then enter to the channel mode setting.
,
【10CH】
,
【7CH】
,
【5CH】,【2CH】
2) Press the【UP/DOWN】button to select【18CH】
3) Press the【ENTER】button to escape and save.
5.6
DIMMING MODE SETTING
Illustrations:When setting【OFF】 in【DIM】menu, there will be no delay dimming
effect. The dimming speed of DIM1-DIM4 is from fast to slow. It will be set【OFF
】automatically in【DIM】menu when showing the shutter effect.
1) Press the【ENTER】button in【DIM】menu, then enter to the dimming mode setting.
2) Press the【UP/DOWN】button to select【OFF】
,
【DIM1】
,
【DIM2】
,
【DIM3】and【DIM4】
3) Press the【ENTER】button to escape and save.
5.7
DISPLAY SETTING
1) Press the【ENTER】button in【DISY】menu, then enter to the display setting.
2) Press the【UP/DOWN】button to select【ON】
,
【2 MINITES OFF】
3) Press the【ENTER】button to escape and save.
5.8
RUN THE AUTO-RUN, AUTO-PROGRAMMING PROGRAM
1)Press the【ENTER】button in【AUTO】menu, then enter to the running the auto-run,
auto-programming program.
-7-
2)Press the【UP/DOWN】button to select【AT01】…【AT33】,【SPEED】,【CHASE01】
…【CHASE03】
3)Press the【ENTER】button to start running.
5.9
EDIT AUTO-PROGRAMMING PROGRAM
1) Press the【ENTER】button in【PROGRAM】menu, then enter to the editing auto-programming
program.
2) Press the【UP/DOWN】button to select【CHASE01】…【CHASE03】
3) Press the【ENTER】button for confirmation and enter to the next menu.
4) Press the【UP/DOWN】button to select【SCENE01】…【SCENE20】
5) Press the【ENTER】button for confirmation and enter to the next menu.
【GREEN1】…… 【WHITE3】
,
【SHUT】
,
6) Then press the【UP/DOWN】button to select【RED1】,
【TIME】
,
【WAIT】
,
【USE】
7) Press the【UP/DOWN】button to set up the parameter which are needed.
8) Press the【ENTER】button to escape and save.
Illustrations:When【USE】 is set to be【NO】,or the
parameter of【TIME】 is 0, it will not run this scene.
When 【WAIT】is set to be FADE time, the running process
isas the right chart showing.
5.10 CHECK THE LIGHTING INFORMATION
1) Press the【ENTER】button in【INFO】menu, then enter to the checking
the lighting information.
2) 【SOFT】button is for software version information.
3) 【LEDs】button is for the LED quantity information.
4) 【POW】button is for the current information of power reduction. It is 100% output in normal
conditions, but 80% or 50% output in over temperature protection situation.
5.11 LIGHTING SETTING PARAMETER RESET
1) Press the【ENTER】button in【ST L】menu, then enter to the lighting setting parameter reset.
2) Press the【UP/DOWN】button to select【YES】.
3) Press the【ENTER】button to escape and save.
5.12 【PROG】AUTO-PROGRAMMING PARAMETER RESET
1) Press the【ENTER】button in【PR L】menu, then enter to the【PROG】auto-programming
parameter reset.
2) Press the【UP/DOWN】button to select【YES】.
3) Press the【ENTER】button to escape and save.
5.13 LIGHTING RESET
1) Press the【ENTER】button in【REST】menu, then enter to the lighting reset.
2) Press the【UP/DOWN】button to select【YES】.
3) Press the【ENTER】button for confirmation of lighting reset.
5.14 LIGHTING PARAMETER DOWNLOADING EACH OTHER
1) Press the【ENTER】button in【SEND】menu, then enter to sending parameter to other lightings.
2) Press the【UP/DOWN】button to select【YES】.
3) Press the【ENTER】button to confirm sending.
-8-
6、DMX PROTOCOL
2CH
5CH
7CH
10CH
22CH
Value
-
CH1
CH1
CH1
CH1
0-255
Dim all
-
CH2
CH2
CH2
-
0-255
Red
-
CH3
CH3
CH3
-
0-255
Green
-
CH4
CH4
CH4
-
0-255
Blue
-
CH5
CH5
CH5
-
0-255
White
-
-
-
-
CH2
0-255
Red 1
-
-
-
-
CH3
0-255
Green 1
-
-
-
-
CH4
0-255
Blue 1
-
-
-
-
CH5
0-255
White 1
-
-
-
-
CH6
0-255
Red 2
-
-
-
-
CH7
0-255
Green 2
-
-
-
-
CH8
0-255
Blue 2
-
-
-
-
CH9
0-255
White 2
-
-
-
-
CH10
0-255
Red 3
-
-
-
-
CH11
0-255
Green 3
-
-
-
-
CH12
0-255
Blue 3
-
-
-
-
CH13
0-255
White 3
0-10
No strobe
CH1
-
-
-
CH6
-
CH6
CH7(CH7
Prior to
CH9)
CH14
CH15(CH15
Prior to
CH17)
Function
11-90
Strobe,slow->fast
91-170
Random Strobe,slow->fast
171-255
Electronic Squarewave,slow->fast
0-5
No effect
6-10
WHITE 1:3200K
11-15
WHITE 2:3400K
16-20
WHITE 3:4200K
21-25
WHITE 4:4900K
26-30
WHITE 5:5600K
31-35
WHITE 6:5900K
36-40
WHITE 7:6500K
41-45
WHITE 8:7200K
46-50
WHITE 9:8000K
51-55
WHITE 10:8500K
56-60
AUTO 1
61-65
AUTO 2
66-70
AUTO 3
71-75
AUTO 4
-9-
-
-
CH8
CH16
76-80
AUTO 5
81-85
AUTO 6
86-90
AUTO 7
91-95
AUTO 8
Remark:
AT01:R,G,B,RG,RB,GB
AT02:R↑,R↓,G↑,G↓,B↑,B↓,W↑,W↓
AT03:R↑G↑,R↓G↓,R↑B↑,R↓B↓,B↑G↑,B↓G↓
AT04:R↑G↑B↑W↑,R↓G↓B↓W↓
AT05:(Rainbow effect)B,BG↑,BG,B↓G,G,GR↑,GR,G↓
R,R,RB↑,RB,R↓B
AT06:R1→R2→R3→R4
AT07:G1→G2→G3→G4
AT08:B1→B2→B3→B4
AT09:W1→W2→W3→W4
AT10:R1G1→R2G2→R3G3→R4G4
AT11:R1B1→R2B2→R3B3→R4B4
AT12:G1B1→G2B2→G3B3→G4B4
AT13:G2R1→G4R3
AT14:R2B2R1G1→R4B4R3G3
AT15:B2W1→B4W3
AT16:R1G2B3→R2G3B4→R3G4B1→R4G1B2
AT17:R1G2G3G4→G1R2G3G4→G1G2R3G4→G1G2G3R4
AT18:G1B2B3B4→B1G2B3B4→B1B2G3B4→B1B2B3G4
AT19:B1R2R3R4→R1B2R3R4→R1R2B3R4→R1R2R3B4
AT20:R1←R2←R3←R4
AT21:G1←G2←G3←G4
AT22:B1←B2←B3←B4
AT23:W1←W2←W3←W4
AT24:R1G1←R2G2←R3G3←R4G4
AT25:R1B1←R2B2←R3B3←R4B4
AT26:G1B1←G2B2←G3B3←G4B4
AT27:G2R1←G4R3
AT28:R2B2R1G1←R4B4R3G3
AT29:B2W1←B4W3
AT30:R1G2B3←R2G3B4←R3G4B1←R4G1B2
AT31:R1G2G3G4←G1R2G3G4←G1G2R3G4←G1G2G3R4
AT32:G1B2B3B4←B1G2B3B4←B1B2G3B4←B1B2B3G4
AT33:B1R2R3R4←R1B2R3R4←R1R2B3R4←R1R2R3B4
96-100
AUTO 9
101-105
AUTO 10
106-110
AUTO 11
111-115
AUTO 12
116-120
AUTO 13
121-125
AUTO 14
126-130
AUTO 15
131-135
AUTO 16
136-140
AUTO 17
141-145
AUTO 18
146-150
AUTO 19
151-155
AUTO 20
156-160
AUTO 21
161-165
AUTO 22
166-170
AUTO 23
171-175
AUTO 24
176-180
AUTO 25
181-185
AUTO 26
186-190
AUTO 27
191-195
AUTO 28
196-200
AUTO 29
201-205
AUTO 30
206-210
AUTO 31
211-215
AUTO 32
216-220
AUTO 33
221-225
CHASE1
226-230
CHASE2
231-235
CHASE3
236-255
Reserved
0—255
Auto speed,fast->slow,(AT01-AT05:0-255S,AT06-AT33:0-25.5S)
Virtual colour wheel
0-10
11
Blue (Blue=full, Red+Green+White=0)(step)
12-50
51
-
-
CH9
CH17
91
Green (Red=0, Green=full, Blue =0, White=0)(step)
Red->up, Green=full, Blue=0, White=0(proportional)
131
Yellow (Red=full, Green=full, Blue=0, White=0)(step)
132-170
Red=full, Green->down, Blue=0, White=0(proportional)
172-210
211
-
CH7
CH10
CH18
Red=0, Green=full, Blue->down, White=0(proportional)
92-130
171
-
Red=0, Green->up,Blue =full, White=0(proportional)
Light Blue (Red=0, Green=full, Blue =full, White=0)(step)
52-90
CH2
No effect
Red(Red=full, Green=0, Blue=0, White=0)(step)
Red=full, Green=0, Blue->up, White=0(proportional)
Magenta (Red=full, Green=0, Blue=full, White=0)(step)
212-250
Red -> down, Green=0, Blue=full, White=0(proportional)
251-255
Blue (Red=0, Green=0, Blue=full, White=0)(step)
0-10
Use menu setting dimmer mode
11-20
Dimmer off
21-30
Dimmer 1
31-40
Dimmer 2
41-50
Dimmer 3
51-60
Dimmer 4
61-254
Use menu setting dimmer mode
255
-10-
Reset(at least 5S)
7、
MAINTENANCE
To
prolong the life of lighting, it is very important to do the maintenance
work. The environment is hash outdoors, or if the lighting is idle for a long
time, damp, dust can cause greater accumulation of dirt on its cover or
housing. So it should be cleaned to maintain an optimum light output and at
the same time to prevent it from corrupted by dust and acid gas.
Cleaning frequency depends on the lighting operation frequency and the
environment in which the fixture operates. Soft cloth and typical glass
cleaning products should be used for cleaning. It is recommended to clean
projector at least once every 20 days.
Do not use any organic solvent,e.g.alcohol, to clean housing of the apparatus.
TROUBLESHOOTING
8、
PROBLEM
REASON AND ACTION

Check the power connection is correct or not.
The lighting can’t be 
Please detect the voltage.
started normally

Power supply is damaged or incorrect connected. Call a qualified
personnel to fix it.

Connection of control board is not correct. Call a qualified personnel
to fix it.

Please check the DMX connector and the power connection is
connected correctly or not. It means having signal if it shows twinkling
of the decimal point which in the lower right corner of the screen
when exiting the screen saver.

Please check the DMX address setting of lighting is correct or not.

Check【CHMD】setting is correct or not.

Please check whether the DMX line is near to the high voltage wire or
not. In that case, it will damage or interfere the DMX electric circuit.

Check whether the 【CAL】is started or not and the set value is too
small.

Check whether the【POW】is in over temperature protection situation
or not, if yes, please take measures for ventilation.
Out of console’s
control
The beam appears
dim ,the brightness
declines obviously
EV LIGHT(GUANGZHOU) CO.,LTD.
ADD:EV INDUSTRIAL PARK,8 CHUANGYE ROAD, TAIPING DEVELOPMENT ZONE, GUANGZHOU
TEL:+86-20-37929678 FAX:+86-20-37929298
WEBSITE: Http://www.evlightpro.com -11-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement