USER MANUAL
USER
MANUAL
AGHD60GG
BUILT-IN 60CM GAS ON GLASS HOB
CUSTOMER CARE
044 800 1128
IMPORTANT INFORMATION
AGHD60GG
CONTENTS
Important Information
Before you start
Safety information
Environment information
Technical and legal information
Your hob
Your controls
Your hob
First use/Setting up your oven
Cleaning the hob
The right gas connection
Product functions
2
3
4
4
5
5
Daily operation of your oven
Use of burners
Care and Maintenance
How to keep your hob in good condition
Gas connection
Installation
Trouble shooting
Guarantee
Useful contacts
7
8
8
9
11
13
14
6
6
6
BEFORE YOU START
To avoid the risks that are always present when you use
an electrical appliance it is important that this appliance is
installed correctly and that you read the safety instructions
carefully to avoid misuse and hazards. Please keep this
instruction booklet for future reference and pass it on to
any future owners. After unpacking the appliance please
check that it is not damaged. If in doubt, do not use the
appliance but contact Apelson on 044 800 1128.
Decide on the appropriate location for your product.
Check the package and make sure you have all of the
parts below.
AGHD60GG Hob x1
Pan supports x1
or handling to prevent personal injury or damage to the
product.
If you sell the appliance, give it away, or leave it behind
when you move house, make sure you also pass on this
manual so that the new owner can become familiar with
the appliance and its safety warnings.
Bracket x4
Triple ring burner x1
Semi rapid burners x2
Seal x1
Cut out template x1
Ø4mm x 25mm screws x4
2
Auxiliary burner x1
Conversion nozzles
x4
IMPORTANT INFORMATION
AGHD60GG
SAFETY INFORMATION
These instructions are for your safety. Please read through
them thoroughly prior to installation and retain them for
future reference.
All installation work must be carried out by a competent
person or qualified electrician.
This appliance must be installed correctly by a suitably
qualified person, strictly following the manufacturer’s
instructions.
This appliance complies with all current European safety
legislation, however, the Manufacturer must emphasise
that this compliance does not prevent the surfaces of the
appliance from heating up during use and remaining hot
during its operation.
Do not allow the electric cables to touch the hot parts of
the appliance.
Make sure that the power cord is not caught under or in
the appliance and avoid damage to the power cable.
Do not remove the plug in the presence of flammable gas.
Do not install the appliance outdoors in a damp place or in
an area which may be prone to water leaks such as under
or near a sink unit. In the event of a water leak allow the
machine to dry naturally.
Please dispose of the packing material carefully.
Do not use flammable sprays in close vicinity to the
appliance.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Regularly check the power plug and power cord for
damage. If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified
persons in order to avoid a danger or injury.
A steam cleaner is not to be used.
The appliance is not intended to be operated by means of
external timer or separated remote-control system.
The appliance is for domestic use only.
The Manufacturer declines all liability for personal or
material damage as a result of misuse or incorrect
installation of this appliance.
Danger of burns! During use the appliance becomes hot.
Care should be taken to avoid touching heating elements
inside the oven.
WARNING! Accessible parts may become hot during use.
Children should be kept away.
WARNING! If the door or door seals are damaged, the
oven must not be operated until it has been repaired by a
competent person.
Do not lean on the door or place any objects on the door
of the appliance. This can damage the door hinges.
The oven should be cleaned regularly and any food
deposits removed.
WARNING! Ensure that the appliance is switched off
before replacing the lamp to avoid the possibility of electric
shock.
The oven must be installed in accordance with installation
instructions and all dimensions must be followed.
Before connecting the appliance to the power supply,
check that the power supply voltage and current rating
corresponds with the power supply details shown on the
appliance rating label.
Never use a damaged appliance! Disconnect the appliance
from the electrical outlet and contact your retailer if it is
damaged.
Danger of electric shock! Do not attempt to repair the
appliance yourself. In case of malfunction, repairs are to
be conducted by qualified personnel only.
To avoid damaging the cord, do not squeeze, bend or
chafe it on sharp edges. Keep it away from hot surfaces
and open flames as well.
Lay out the cord in such a way that no unintentional
pulling or tripping over it is possible.
Keep the appliance and its cord out of reach of children.
Do not operate the appliance with wet hands or while
standing on a wet floor. Do not touch the power plug with
wet hands.
Connect the power plug to an easily reachable electrical
outlet so that in case of an emergency the appliance can
be unplugged immediately. Pull the power plug out of the
electrical outlet to completely switch off the appliance. Use
the power plug as the disconnection device.
Means for isolating the appliance must be incorporated
in the fixed wiring in accordance with the current wiring
regulations. An all-pole disconnection switch having a
contact separation of at least 3 mm in all poles should be
connected in fixed wiring.
Disconnect the power plug from the electrical outlet when
not in use and before cleaning.
Always turn the appliance off before disconnecting the
power plug.
3
IMPORTANT INFORMATION
AGHD60GG
This appliance is classified as protection class I and must
be connected to a protective ground (Earth).
Means for full disconnection must be incorporated in
the fixed wiring in accordance with the wiring rules. To
achieve this install an appropriate circuit breaker (CB) and
residual current device (RCD). It should be installed in an
easily reachable place so that in case of emergency the
appliance can be disconnected from power immediately.
The fixed wiring must be protected against heat surfaces.
Do not hang an objects to the handle of the oven door.
Do not cover the bottom of the oven with aluminium foil or
other objects. Caution: Risk of fire!
Do not allow aluminium foil, plastic, paper or fabric contact
with heating elements.
Do not store or never use harsh chemicals, sprays,
flammable or non-food in or near the oven. Oven is
designed specifically for heating or cooking food. The use
of corrosive chemicals in heating or cleaning will damage
the unit and may cause injury.
Should any food inside the oven catch fire, keep the
door closed. Switch the oven off and disconnect the power
supply.
Always exercise caution when opening the door. Move
to side, open the door slowly to vent the hot air and/or
steam. Make sure your face is away from the opening and
make sure there are no children or pets near the oven.
Only use utensils that are suitable for use in this type
of oven.
Never leave the appliance unattended during use,
especially when cooking with flammable substances (e.g.
hot oil, fat, etc.).
ENVIRONMENTAL INFORMATION
TECHNICAL AND LEGAL INFORMATION
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your Local Authority or
retailer for recycling advice.
TECHNICAL INFORMATION:
This symbol on the product or its packaging
indicates that this product cannot be treated
as normal household waste. This product must
be handed over to an electric and electronic equipment
collection point for recycling.
On ensuring that this product is disposed of correctly, you
will help to avoid possible negative consequences for the
environment and public health, which could occur if this
product is not handled correctly. To receive more detailed
information about recycling this product, contact your
local government, domestic waste disposal services or the
outlet where the product was bought.
4
Power supply: Gas pressure
Measurements:
External dimensions (WxHxD): Net weight: 220-240V~, 50/60Hz
G20 type/20mbar/8.3kW
G30 type/28mbar/8.3kW
560x39x510mm
15.7kg
LEGAL INFORMATION
The Manufacturer declines all liability for damage caused
to persons and objects due to incorrect or improper
installation of the appliance.
YOUR+2%
AGHD60GG
YOUR CONTROLS
A
C
B
D
A. Front left control dial
C. Rear right control dial
B. Rear left control dial
D. Front right control dial
YOUR HOB
A. Auxiliary burner
B. Semi-rapid burner
B
C. Triple ring burner
E
B E
D. Hob
C
E. Burner caps
A E
E
D. Pan supports
D
F
5
FIRST USE/SETTING UP YOUR +2%
AGHD60GG
We recommend that you read the instructions in this owner’s manual carefully before use for the best performance and to
extend the life of your appliance, as it will provide you with all the instructions you require to ensure its safe installation,
use and maintenance. Always keep this owner’s manual close to hand since you may need to refer to it in the future.
Thank you.
CLEANING THE OVEN FOR THE FIRST TIME
THE RIGHT GAS CONNECTION
Before using the hob for the first time we recommend
that hob burners are switched on and set to there highest
temperature for 30 minutes with nothing on them. Ensure
adequate ventilation during this process by opening any
doors and windows in the room. Any odours created
during this operation will be due to the evaporation of
substances used to protect the appliance during storage
prior to installation.
This oven can be use on NATURAL GAS or LPG.
It is a legal requirement that all gas appliances are
Installed & Serviced by a competent person in accordance
with the current editions of the following Standards &
Regulations:
Gas Safety (Installation & Use) Regulations
Building Regulations
British Standards
Regulations for Electrical Installation
Installation and service of any gas product must be made
by a suitably qualified and registered person competent
on the type of product being installed or serviced and
holding a valid certificate of competence for the work
being carried out.
PRODUCT FUNCTIONS
The gas hob has 4 cooking zones using 3 different types of
burners to give you flexibility with you cooking.
with a flame failure device (FFD) which stops the gas
supply to the hob when the flame goes out.
The hob is equipped with auto ignition and is also fitted
This hob is also supplied with an LPG conversion kit.
Max output
Min output
kW
kW
Nozzle size
(mm)
Cons
m3/h
Nozzle size
(mm)
Cons
g/h
Nozzle size
(mm)
Cons
g/h
Auxiliary
burner
1.00
0.35
0.72
0.095
0.50
73
0.43
73
Semi-rapid
burner
1.75
0.65
0.97
0.167
0.63
127
0.58
127
Triple flame
burner
3.80
1.9
1.35
0.362
0.98
277
0.77
277
Burner
type
6
G20 20mbar
G30 28-30mbar
G30 50mbar
DAILY OPERATION OF YOUR +2%
AGHD60GG
This gas hob can be used with both natural gas and LPG.
USE OF THE BURNERS
On the right bottom side of each dial on the control panel
there is a diagram to indicate the burner to which the
dial refers to. The burners can be switched on in several
ways, according to the type of appliance and its individual
features.
Manual “ON” switch (this is always
possible even if the electric current
is off):
Turn the knob corresponding to
the selected burner in a counterclockwise direction so that the knob
is at MAXIMUM (this corresponds to a
large flame).
Use a piezo electric spark gas igniter.
Automatic electric “ON” switch for burners with safety
device (thermocouples):
Turn the knob corresponding to the selected burner
in a counter-clockwise direction so that the knob is at
MAXIMUM.
ADVICE FOR THE BEST USE OF THE BURNER:
When boiling point is reached, turn the knob to MINIMUM.
Always use pans with a lid.
Burners
Recommended pan diameters (cm)
Auxiliary
8-16
Semi-rapid
12-20
Triple ring
22-26
NOTE
The use of a gas cooking appliance produces heat and
humidity in the place where it is installed.
Therefore, you need to ensure the place is well ventilated,
keeping the natural ventilation openings clear and using a
mechanical ventilation device/ flue or electric fan.
Intensive or prolonged use of the appliance may require
additional ventilation, such as opening a nearby window or
increased ventilation efficiency obtained by increasing the
power of the mechanical ventilators, where applicable.
Once the burner is lit, keep the knob pressed in for about
10 seconds in order to allow the flame to heat up the
thermocouple. If the burner goes out when the knob is let
go, repeat the operation.
CAUTION
If there is no electric current you can light the burners
with piezo electric spark gas igniter.
The burners can only be lit with safety thermocouples
when the knob is on MAXIMUM.
7
CARE AND MAINTENANCE
AGHD60GG
WARNING
Always switch off the electricity supply before
performing maintenance work. In the event of a
fault, contact customer services.
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
FUSE
ON
USE A 30 AMP FUSE
The surface of the hob may be easily cleaned as follows:
Cleaning of enamel parts:
To maintain the features of the enamel parts, wash
frequently with soapy water.
Use soapy water and a cloth for cleaning. Never use
abrasive powders.
Never use abrasive powders. Avoid leaving acid or alkaline
substances on the enamel parts (vinegar, lemon juice, salt,
tomato juice, etc.) and washing the enamel parts while
they are still warm.
Avoid banging pots and pans down on the hob.
Cleaning of glass/stainless steel parts:
Do not leave any empty pan on the heating zone
Wash these parts with soapy water and then dry them
with a soft cloth.
CAUTION
HOW TO KEEP YOUR HOB IN GOOD
CONDITION
Before cleaning your oven, or performing maintenance,
disconnect it from the power supply.
The appliance should be cleaned after use.
Wipe the inner and outer surface of the appliance and its
accessories with wet cloth.
Any liquid overflowing from the pan must always be
removed with a cloth.
The shine is maintained by regularly cleaning them with
special products normally commercially available. Never
use abrasive powders.
Cleaning of burner flame dividers:
Given that they are not fixed, the flame dividers can be
cleaned by simply removing them and washing them with
soapy water. After drying them well and checking that the
holes are not blocked, put them back into their correct
position.
GAS CONNECTION
Turn on the burner and turn the knob to its MINIMUM
position (small flame).
CHANGING THE NOZZLES
Remove the knob from the tap set for standard pressure.
The knob is found on the bar of the tap itself.
Lift up the burners and unscrew the nozzle using an
dedicated tool and replace the nozzles with those designed
for LPG gas supply
x1x1
[conversion
[conversion
nozzles]
x4
nozzles]
x4
[conversion
[conversion
nozzles]
nozzles]
CAUTION
The hob installation and burner changes must be carried
out by a competent person, e.g. a gas safe registered
fitter.
NOTE
The LPG nozzles are provided in a separate bag marked
“LPG” and if they are changed and the natural gas jets
retained then the label should be changed to “NATURAL”.
REGULATION OF BURNERS
Regulation of the “MINIMUM” position on the burners.
To regulate the minimum position on the burners, follow
the procedure below:
8
Place the tap bar on the work top, use a small screwdriver
that fits the (gold) screws located at the lower part of
the tap and turn the fixing screw to
the right or left until the flame of
the burner is regulated in the most
suitable manner to MINIMUM.
Make sure that the flame does not
go out when changing the position
quickly from MAXIMUM to MINIMUM
position.
INSTALLATION
AGHD60GG
instructions provided must install the appliance. The
manufacturer declines all responsibility for improper
installation, which may harm persons and animals and
damage property.
CAUTION
The power supply to the appliance must be switched
off before any adjustments or maintenance work is
undertaken.
INSTALLATION OF GAS HOB
ELECTRICAL CONNECTION
All installation work must be carried out by a competent
Before connecting the mains supply ensure that the
mains voltage corresponds to the voltage on the rating
plate inside the cooker hood.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Mains Supply could be connected to the Mains Voltage
by Direct Connection
WARNING
WARNING
Good ventilation is required around the appliance for
easier dissipation of heat and low power consumption.
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
Make sure the fused spur outlet is
located in an accessible position.
FUSE
ON
DIRECT CONNECTION
The gap between the hob and any cooker hood above it
should be at least 750mm.
The gap between the hob and any adjacent wall cabinet
above should be at least 450mm.
USE A 3 AMP FUSE
If the appliance is being connected
directly to the mains an omnipolar
circuit-breaker must be installed with a minimum
opening of 3mm between contacts.
If the cable is damaged or to be replaced, the operation
dedicated tools to avoid any accidents.
The installer must ensure that the correct electrical
connection has been made and that it complies with
wiring diagram.
450mm
450mm
The cable must not be bent or compressed.
750mm
750mm
At least
300mm
At least
300mm
The cable must be checked regularly and replaced by
authorized technicians only.
ELECTRICAL REQUIREMENTS
Any permanent electrical installation must comply with
the latest I.E.E. Regulations and local electricity company
contractor who is on the roll of the National Inspection
Council for Electrical Installation Contracting (NICEIC)
should undertake the electrical installation.
Electrical Connection
75mm
75mm
At least
300mm
At least
300mm
Before connecting the mains supply ensure that the
mains voltage corresponds to the voltage on the rating
plate inside the appliance.
WARNING:
THIS APPLIANCE MUST BE EARTHED
The appliance is supplied with a 3-core mains cable and
must be connected to the electricity supply via a double
pole switch having a 3mm minimum contact gap on each
connector.
9
INSTALLATION
AGHD60GG
Cut out worktop to the template dimensions with suitable
equipment and seal the cut edge with appropriate sealant
SI
30mm
E
N
O
C
LI
Secure with brackets
[screw]
40mm
[bracket]
[screw]
[bracket]
VENTILATION
Stretch out the supplied seal along the underside edge of
the hob, ensuring the ends overlap.
All rooms require a window or equivalent (e.g. a door)
which can be opened. Some rooms require a permanent
vent or extractor in addition to a window (see below).
This unit must not be used in a room which is less than
5m³. The following table details the requirements based
on the kitchen volume (L x W x H) in m³.
The above requirements also allow use of a gas oven and
grill but if there are any other fuel burning appliances
in the same room, consult the relevant British Standard
(BS5440) or Gas Safe manual.
[seal]
Drop the hob into position.
Room Volume (m3)
Air vent required (cm3)
5
100
6 to 10
50
6 to 11
No permanent vent
required if a door opens to
the outside
11 or more
None required
The above requirements also allow use of a gas oven and
grill but if there are any other fuel burning appliances
in the same room, consult the relevant British Standard
(BS440) or Gas Safe document.
WHAT YOU SHOULD DO IF YOU SMELL GAS?
Switch off the gas supply
Open doors and windows
Call Transco 0800 111 999
THE APPLIANCE IS NOW READY TO USE.
10
TROUBLESHOOTING
AGHD60GG
The following circumstances may not be a problem. Do not
contact the customer services until the problem has been
confirmed.
If your appliance is still not functioning properly after
making the checks, please contact customer services.
CHECK…
… that the mains supply has not been switched off.
… that the fuse in the spur has not blown.
… that the burner components are not excessively soiled
as this can lead to ignition problems.
… that the appliance is correctly connected.
Do not take the appliance apart yourself, as you may
damage the hob.
Before calling After Sales Service, please do the following:
If you are still unable to solve the problem, switch off the
appliance and call customer services.
11
GUARANTEE
AGHD60GG
This appliance is covered by a full manufacturer’s 2 year
parts and 2 year labour guarantee and covers all parts and
labour costs associated with the repair of the appliance
in a domestic environment. We will repair any defect that
arises due to faulty materials or workmanship and use
genuine manufacturers parts.
All claims must be supported with the original receipt or
other reasonable proof of purchase.
If, during the guarantee period, the appliance becomes
irreparable as agreed by the engineer approved by
Apelson Appliances UK Ltd then we reserve the right, at
our discretion, to exchange the defective product with
a replacement appliance at Apelson Appliances UK Ltd
sole cost. If the same product is no longer available an
alternative will be offered with the same functions as the
faulty item.
After an appliance has been repaired or replaced any
remaining balance of the Apelson Appliances UK Ltd
guarantee will be valid and any further call outs during this
prescribed period will be covered by Apelson Appliances
UK Ltd on the replacement appliance.
Should any person other than an authorized engineer
modify or attempt to repair the appliance then the
warranty will be invalid.
The guarantee applies to the UK mainland, Scotland and
Ireland but is not transferable between EU countries.
This guarantee is non-transferable to any other person or
product.
The guarantee is covered by UK law and is in addition to
and does not diminish your legal rights.
EXTENDED PARTS ONLY WARRANTY
As testimony to our commitment to you as a valued
customer of Apelson Appliances UK Ltd, we will offer you
an additional 3 years parts warranty absolutely free.
If during the extended parts warranty period the
12
appliance fails and it is considered uneconomical to repair
our Customer Service Department will offer you the
opportunity to purchase the same or equivalent model at a
discounted price.
All parts supplied free of charge under the extended
warranty must be fitted by our approved engineers and
will be subject to a call out charge to fit the part.
EXCLUSIONS TO THE GUARANTEE
This guarantee does NOT cover:
Appliances that have been damaged or neglected as a
result of failure to store, assemble, install, use or care
of the products in accordance with the manufacturer’s
instructions - Apelson Appliances UK Ltd will not accept
responsibility under this guarantee if a product is damaged
or becomes defective due to, misuse, neglect, wilful or
accidental damage or act of god.
Normal wear and tear.
Consumable items such as carbon filters and bulbs.
Claims arising from non-domestic use or commercial
environment.
Any gas appliance not fitted by a gas safe qualified
installer.
If no fault is found then Apelson Appliances UK Ltd
reserves the right to charge for the call out at the going
rate of £55.00 plus VAT.
In the course of the service work carried out it may be
necessary to remove the built in appliance from its fitted
position. If the appliance is glued, grouted or tiled in such
a manner that it cannot be removed, it is the responsibility
of the customer/installer to remove and reinstall the
appliance to facilitate the repair.
This Guarantee does not affect your statutory rights.
The guarantee is offered by Apelson Appliances UK Ltd,
8QLW1RUPDQG\/DQGLQJV3RSH6WUHHW&DVWOHIRUG:$$*
USEFUL CONTACTS
AGHD60GG
USEFUL CONTACTS
TECHNICAL SUPPORT
Apelson Appliances UK LTD
Phone: Email: [email protected]
Web: www.myspareparts.co.uk
SPARES
Apelson Appliances UK LTD
Phone: 0 800 1128
Email: [email protected]
Web: www.myspareparts.co.uk
SERVICE AND GUARANTEE
Apelson Appliances UK LTD
Phone: 044 800 1128
Email: [email protected]
Web: www.myspareparts.co.uk
13
APELSON APPLIANCES UK LTD,
Unit 3 Normandy Landings
Pope Street
Castleford
WF6 2AG
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement