Microsoft Word VIN-CS-TS User Manual
Table of Contents
C HAP 1
OD
UCT
ATURE
S.................................................................................. 3
B RIEF INTR
INTROD
ODUCT
UCTIION & FE
FEA
URES
1.1 SY STEM OVE RVIEW .......................................................................... 3
1.2 F EATURES ................................................................................. 3
C HAP 2
TAL
LATION & C ON NECTION ......................................................................................... 5
INS
INST
ALL
2.1 SYSTEM CONFIGURATION ......................................................................... 5
2.2 SYSTEM APPEARANCE ........................................................................... 6
2.2.1 CS Pla stic Series ............................................................................................................................................... 6
2.2.2 TS Metal Serie s ............................................................................................................................................. 7
2.3 INSTALLATION PROCEDURE ........................................................................ 7
2.4 INSTALLATION WARNING ......................................................................... 8
2.5 DIRECT ACCESS WHEN POWER FAILURE ............................................................... 8
C HAP 3
GRA
MMIN
G....................................................................................................... 9
SYSTEM PRO
PROG
RAM
MING
3.1 BEFORE PROGRAMMING ........................................................................... 9
3.2 BASIC COMMAND .............................................................................. 9
3.2.1 Enter into System Progra mming Status ............................................................................................................ 9
3.2.2 Change the Password...................................................................................................................................... 10
3.2.3 System So ft-Reset .......................................................................................................................................... 10
3.2.4 Flash time setting............................................................................................................................................ 10
3.2.5 System return to default setting ...................................................................................................................... 10
3.2.6 Set to Delaying mode ......................................................................................................................................11
3.3 ENABLE /DISABLE C.O. LINES ................................................................... 11
3.3.1 Enable C.O. Lines............................................................................................................................................11
3.3.2 Disable C.O. Lines ..........................................................................................................................................11
3.3.3 Trunk lines(c.o.lines) working assignment (UCD) ......................................................................................... 12
3.4 SETTING OPERATING MODE ...................................................................... 12
3.4.1 Setting Auto-attendant Mode (OGM) for C.O. Lines ..................................................................................... 12
3.4.2 Operator Busy Process.................................................................................................................................... 13
3.4.3 Setting Operator Mode for C.O. line .............................................................................................................. 13
3.4.4 System CRBT Setting..................................................................................................................................... 13
3.5 OGM RECORDING/MONITORING (FOR CS/TS SERIES) ................................................... 13
3.5.1 OGM Recording ............................................................................................................................................. 13
3.5.2 OGM Monitoring............................................................................................................................................ 14
3.5.3 System Music Monitoring .............................................................................................................................. 14
3.6 OGM RECORDING/MONITORING (FOR CS+/TS+ SERIES ) ................................................. 14
3.6.1 OGM Recording and setting to three paragraph mode ................................................................................... 14
3.6.2 Monitoring the recorded OGM and setting to three paragraph mode ............................................................. 15
3.6.3 One paragraph OGM Mode ............................................................................................................................ 15
3.7 AUTO-ATTENDANT MODE SETTING .................................................................. 15
3.7.1 No Answer Process......................................................................................................................................... 15
3.7.2 Extension Busy Process.................................................................................................................................. 16
3.7.3 No Answer Process......................................................................................................................................... 16
3.8 OPERATOR SETTING ........................................................................... 16
3.8.1 Operator Setting.............................................................................................................................................. 16
3.8.2 Fast Diali ng Operator ..................................................................................................................................... 16
3.9 OPERATOR ATTENDANT RINGING SETTING ............................................................. 16
3.9.1 Ringing mode when all the ringing extensions is busy ................................................................................... 16
3.9.2 Ringing Extensions Assignment/ to Cance l in Day mode............................................................................... 17
3.10 EXTS . DIALING-OUT MODE ..................................................................... 17
3.11 CALLING RESTRICTION SETTING ................................................................. 18
3.11.1 Calling Tim e Restriction Setting................................................................................................................... 18
3.11.2 Calling Restriction-Class Setting .................................................................................................................. 18
3.11.3 Calling Restriction Item................................................................................................................................ 19
3.11.4 Assign Special Cal ling-out Number.............................................................................................................. 20
P1
3.12 EXTS . USING C.O. LINES ACCESS .............................................................. 21
3.13 FL EXIBLE CODING ......................................................................... 21
3.14 RINGING /TRANSFER /RESERVATION TIME ............................................................ 22
3.14.1 Internal Call Ringing Time ........................................................................................................................... 22
3.14.2 Operator Dialing/Transfer Ringing Time...................................................................................................... 22
3.14.3 No Answer Transfer Time............................................................................................................................. 22
3.14.4 External Line Reservation Time ................................................................................................................... 22
3.15 TRANSFER OPERATION PARAMETER ................................................................. 22
3.15.1 External Transfer Mode ................................................................................................................................ 22
3.15.2 External Transfer No Answer Ringing Back................................................................................................. 23
3.15.3 Off Pla ce/Busy/No Answer Transfer Power-Down Conservation................................................................. 23
3.16 CID FUNCTIONS SETTING (FOR CS+/TS+ SERIES ) ................................................... 23
3.16.1 Add digits for intercom CID ......................................................................................................................... 23
3.16.2 Internal CID mode(transmit mode) setting ................................................................................................... 23
CH AP 4
ATING IN STR
U CTI
ON .................................................................................................. 24
OPER
OPERA
STRU
CTIO
4.1 O PERAT OR ATTENDANT M ODE ................................................................ 24
4.2 A UTO-ATTENDANT M ODE ..................................................................... 24
4.3 O FF PLACE/BUSY/NO ANSWER TRANSFER PROGRAMMING.......................................... 24
4.4 DIALING C.O. LINES ........................................................................ 24
4.5 BOOKING C.O.L INES ........................................................................ 24
4.6 O UT WARD DIALING BY AN E X CLUSIVE L INE ....................................................... 24
4.7 O UTGO ING CALL T RANSFER .................................................................. 25
4.8 COMING CALL PICKUP ....................................................................... 25
4.8.1 Call Pickup Extension................................................................................................................................. 25
4.8.2 General Call Pickup .................................................................................................................................... 25
4.9 CALL TRANSFER (EX TERNAL CALL ) ............................................................ 25
4.10 THREE WAY CONFERENCE .................................................................. 26
4.11 C.O. LINE RESE RV AT ION .................................................................... 27
4.12 C.O. L INE TRANSFER TO C.O. LINE............................................................ 27
4.13 FAST RES ERV AT ION TRANSFER ............................................................... 27
4.14 CALL SWIT CH (CALL P ICK DURING CONVERSAT IO N) ............................................... 28
4.15 INTERCOM CALLING ........................................................................ 28
4.16 DIALING OPERATOR ....................................................................... 28
4.17 INQUIRY FUNCTIONS (A UT OMATIC REPO RT ING) .................................................. 29
4.17.1 Reporting of Physics Number................................................................................................................. 29
4.17.2 Automatic reporting of Ext number......................................................................................................... 29
4.18 PRIORIT Y A CCESS AND M ONIT ORING .......................................................... 29
4.19 CALL FORWARDING ........................................................................ 30
4.20 CALL FORWARDING W HEN EXT IS BUSY OR NOBODY AVAILABLE ..................................... 30
4.21 DON ’T DISTURB SETT ING ................................................................... 30
4.22 CALL AL L EXT ENSION ...................................................................... 30
4.23 CLEAR EXT ENSION FUNCTION SETT ING ........................................................ 31
APPENDIX I
TEN
ANCE & TR
OUBLE
SHOOTI
NG ............................................................ 31
MAIN
MAINT
ENA
TRO
UBLES
OOTIN
1.Outgoing calls can’t be made .......................................................................................................................... 31
2.Outside calls can’t dial in .................................................................................................................................. 31
3.Intercom can’t be made .................................................................................................................................... 31
APPENDIX
APPENDIX
APPENDIX
II GLOSSA
RY ......................................................................................................... 32
GLOSSAR
FAU
LT SE TTINGS ................................................................................... 33
III DE
DEF
AUL
OGR AMMI
N G & OPE
R ATION INS
TR U CTI
ON ............................................ 34
IV PR
PRO
AMMIN
OPER
INST
CTIO
1.
INDEX OF BASIC OPERATION ................................................................ 34
2. I NDEX OF SYSTE M PROGRAMMING ............................................................... 35
P2
Chap 1
Brief Introduction & Features
1.1 System Overview
With its design and manufacture according to G.712 and G.732 protocols of CCITT, the
system integrates virtues of various KTSs with advanced functions of PABX, and has unique
advantage in innovation. As a type of new generation with over 50 powerful functions for business
and management, it has wide application in offices, enterprises, hotels……etc. In a word, it is a
ideal equipment for users to better communication conditions, improve work efficiency, control call
fee payment, and make office intelligent come true.
1.2 Features
Normal phone programming
programming:use normal phone programming, not need the specialized key
phone.
S ystem CRBT Function
Function:except for operator and auto-attendant mode, the system can play
the OGM without dialing any number. Connect with the computer, can record the promote
information of the and play it to customers. (same as the CRBT of ISP)
Mutiple Dial-Out Mode
Mode:: Can choose dial-out number 9 or direct dial CO line.
‹ Coming Call Prompt: When all the extensions are busy, if external line calling (including
door phone), the system will prompt the set ringing extension.
nce of the ringing: internal call, external call and door phone call have different
‹ Differe
Differen
ringing.
er ID (CTS Seri
al): when CO.Line call in or other Extension call ,you can see Cid
‹ Transfe
ransferr Calllle
ria
number in telephone;also the incoming CID number will follow while call transferred.
d ant/Operat
o r Mode: the incoming calls from C.O. lines can be set up the
‹ Auto-a
Auto-attten
tend
ant/Operato
operator mode or the auto-attendant mode freely.
o ut Setting: can set any ringing extension and the using access of CO lines.
‹ Dial in/
in/o
‹ CO Line Bo oking: when the CO lines are busy but urgently to call, the system will prompt the
extension when CO line available.
ation: any extension can reserve the CO line and do others operations.
‹ CO Line Reserv
Reserva
‹ Three Way Conference and External transfer Function: allows to add a third party to a
two-party conversation and make a three-party conference. You can have only two Ext. with
one C.O.line. And can make an outgoing call from one Ext then divert and connect other Ext
to C.O.line.
P3
er and Pickup: all external and internal calling can be transferred, other ext.
‹ Call Transf
ransfe
ringring can be picked up and not need answer the ringring ext. This system have many kind
of pickup ways, including exts. pickup, CO line pickup and reservation, etc.
‹ Operator Function: This system can be set two operator for reservation, call forwarding, call
transfer and manager secretary.
‹ External Ca
Calll Sw itch (call pickup during conversation): during the conversation with CO
line, if other CO lines or door phone calling, just easy reserve the answering CO line and
pickup the calling call.
e:allow you to change the system holding music freely.(optional)
‹ External Music interfac
interface
Flexible extension number
number:The number of extension can be set up one to four digits.
u re Memor
P ower Fail
Failu
Memoryy: when power failure, the system can remain all the settings and just
use all the functions when power again.
‹ Remote co ntrol prog
progrramming: It can sustain remote maintenance, process remote
control programming, detect and maintain, which facilitate the users to install and test, and
provide quick and effective service to users.
P4
Chap 2
Installation & Connection
Before Ins
Insttallation
For easy and quick installation and connection, it is strongly recommended that the user read
and follow the following instruction carefully so as not to damage the system accidentally by
incorrect operation.
on
2.1 System Configurati
Configuratio
This system capacity smallest is 208, biggest is 416.
s)
CS ( plastic cover
covers
TS (me
(mettal covers)
CO Line Ports
Exts. Ports
DISA
Music On
Holding
CS208 CS308 CS312 CS416
2
3
3
4
8
8
12
16
10s one paragraph
Piano music, external music input on
holding is optional
TS208 TS308 TS312 TS416
2
3
3
4
8
8
12
16
10s one paragraph
Piano music, external music input on
holding is optional
Caller ID
External line caller ID
External line caller ID
Model
Please according to the capacity and functions of your machine when install
and program the system.
P5
2.2 System Appearance
2.2.1 CS Plastic Series
Po
w er Indicator Light
①Po
Pow
308 C.O.Line Port
④308
416 Ex
⑦416
Extts. Port
C.O.Line Indicator Lig
ht
②C.O.Line
Ligh
308 Ex
⑤308
Extts. Port
P6
Ground Port
③Ground
416 C.O.Line Port
⑥416
2.2.2 TS Me
Mettal Series
Po
w er Indicator Light ②C.O.Line
C.O.Line Indicator Lig
ht ③Ex
Ex
①Po
Pow
Ligh
Extts. Indicator Light
C.O.Line Port
Ex
Po
wer Socket
④C.O.Line
⑤Ex
Extts. Port
⑥Po
Pow
Pow er Swi tch
External Music Interface
⑦P
⑧External
Door
Lock
Interfa
c
e(optional)
⑨Door
Interfac
2.3 Ins
Insttallation procedure
¾
¾
¾
¾
¾
Before installation, please check all the parts if have any looseness, take care the supply
power switch if is shut down.
The telephone exchange shall be installed in a stable indoor place with dry, ventilated
environment. (Temperature Range: 0-45℃, Humidity Range: 20%-80%.Avoid straight sun
shine or in the environment of flammable or caustic gas.) Special telephone wire is
preferable.
A wall bore is available at the underside of mainframe for wall installation. Desk installation
is also admitted. But the contact of wall bolt and circuit board inside the mainframe should
be avoided.
None of the wiring of any extension should share the pipeline with power supply or antenna.
Neither should the extension be close to antenna for air broadcasting (including
short-wave).
For the sake of personal safety and communication quality, grounding of PABX should be
reliable. Or else, the lightning-proof device inside would fail to work.
Resistance to ground should be less than 5 ohm.
P7
Grounding as follows:
¾
¾
Connect the monomer-crystal with EXT. line and C.O. line separately..
Connecting extensions according to the in-dilated extension positions and C.O. lines to the
corresponding line ports on the unit.
¾
The C.O. lines will be connected direct to the special Exts automatically when the power failure. The No.1
C.O. line will be connected to Ext. 601 and No.2 to Ext.602, No.3 to Ext.603, No. 4 to Ext.604. So you only
can use the four Exts as normal phone with direct C.O. line.
¾
Test the system according to the default settings.
2.4 Ins
Insttallation Warning
1.
The wiring should not be done in thundering.
2.
Avoid using telephone in thundering.
3.
Please don't use the telephone in flammable and leaking gas environment.
4.
Unless the equipment is disconnected, please don't touch the broken part of the wiring or any
connection ends.
● Note: Lightning stroke is an accident, which will not be regarded as normal maintenance.
2.5 Direct Access when Power Failure
The C.O. lines will be connected direct to the special Exts automatically when the power
failure. The No.1 C.O. line will be connected to Ext. 601 and No.2 to Ext.602, No.3 to Ext.603,
No. 4 to Ext.604. So you only can use the four Exts as normal phone with direct C.O. line.
For example when someone call in with No.1 C.O. line at the time of power failure, the
Ext.601 will ring, you can only pick up Ext. 601 and talk with the caller.
P8
Chap 3
System programming
3.1 Before programming
● All the programming must be carried out on the extension 601, 602, 603, 604; all the
programming must be into system programming status.
●All the extensions must be of dual tone multi-frequency phone.
●You are allowed to operate one by one, and end the process by simply pressing #. You
don’t have to hang up if something wrong occurs, you could press * to restart.
● If programming-extension (601,602,603,604) is in Direct-Dialing-Out mode, you need to
press * to enter the internal system, then start programming.
●When the setting is finished, a long beep indicates that the setting is done correctly and
saved in the system. If instead an array of short chirps is heard, that would indicate an error
occurred in the setting. You need to check it out and reset the system. It is only after the end
of the long beeps you can continue another system operation.
●You must use “enable C.O. lines” command according the actual trunk lines before using
this product, if you don’t enable any C.O. line, the system will consider there is no C.O. line
and doesn’t auto detect C.O. line.
How to programming
At first you must according 3.2.1 instruction enter into system programming status, and then
you can begin to program as the following instruction.
3.2 Basic Command
3.2.1 Enter into System Programming Status
Format:
# * EFGH
Explanation: EFGH is the system password now.
Example: For programming the system, you should enter the password first, now the
password is 5678
P9
1. You are required to dial: * # * EFGH in the Direct-Dialing-Out mode.
2. The default password is 0000, so you must enter 0000 in the first use
3. Programming telephone is EXT601, or EXT.602, or EXT.603, or EXT. 604
w ord
3.2.2 Change the Pass
Passw
Format: 09EFGH#
Explanation: EFGH is the new system password.
Description: to change the password of system programming.
Example: Changing the system password from “0000” to “5678”
1. We suggest changing the password before using.
3.2.3 Syst em So
Sofft-Reset
Format: 0 9 9 9 9 9 9 9 #
Description: to reset the system when the system power on.
3.2.4 Flash time setting
Format:
0 0L #
L=1 ---------0.8s L=2 ---------1.0sL=3 ---------1.2sL=4 ---------1.5sL=5 ---------1.8s
Explanation: L means the flash time grade.
Description: For active the hold and divert operating use.
In default setting: L=2 (1.0s)
Example: Set the flash time to 1.2S
3.2.5 System return to default setting
Format: 0 0 0 0 #
Description: when returning to default setting, please wait and hear the confirm sound that means
ok. Default setting please see the Chapter 8. This action will not effect the data of the charging.
1. this format can not return the flexible code extension number, also can not effect the
P10
C.O. lines opening and shuting, also can not effect the charging data.
2. If want to return the extension number default setting, input 9000#
3.2.6 Set to Dela
yi ng mode
Delay
Format:
0 3TT#
Description: Select all C.O.line to charge mode of Delay billing, TT – delay time (01-99 sec.),
which is from finish dialing to the system start to charge
Default setting: Duration of time-delay being 5 seconds.
Example: Setting delay time: 20s, input: 0320#
a ble C.O. Lines
3.3 Enable/Dis
Enable/Disa
You must use these commands according the actual trunk lines before using this
product!!! If you don’t enable any C.O. line, the system will consider there is no C.O. line and
doesn’t auto detect C.O. line!!!
3.3.1 Enable C.O. Lines
Format: 0600#
Description: Enable all C.O. lines
Format: 060M#
Explanation:
M: C.O. line No. M = 1 - 4
Description: Enable the M C.O. line
Example:
You have 308 model product, you want use C.O. line 1 and C.O. line 2, and the line
3 is not in use.
3.3.2 Disable C.O. Lines
Format: 0610#
P11
Description: Disable all C.O. lines
Format: 061M#
Explanation:
M: C.O. line No. M = 1 - 4
Description: Disable the M C.O. line
o.lines) w orking assignment (UCD)
3.3.3 Trunk lines(c.
lines(c.o
Format:
0 62 0 #
Description: This setting make the system assign the different trunk lines working averagely, it
means the system will use the trunk lines circulating. (For example: the system will use trunk line
01, then line0 2, line03, ……line16 circulating). This setting can avoid the user always use some
trunk lines.this is default setting.
Format: 0 6 2 1 #
Description: This setting make the system use trunk lines in sequence, it means the system
always choose the trunk line of lower number if available. (line 01 is the lowest
number)
3.4 Setting Operating mode
3.4.1 Setting Auto-attendant Mode (OGM) for C.O. Lines
Format:
1 0 #:
Description: allows all the C.O. lines in Auto-attendant Mode (DISA --Direct Inward System
Access status). In this mode, Caller will hear the OGM recorded message, while
all extensions are in MUTE mode
1. If the caller doesn’t know the extension number, he cans inquiry the operator by
dialing “0”.
2. Outgoing Message must be record when setting this mode.
Format:
1 0M #
Explanation: M: C.O. line No.1-No.4
Description: allows the No.M C.O. lines in Auto-attendant Mode( DISA --Direct Inward System
Access status).
P12
Example: Set C.O. line 2 and 4 in Auto-Attendant mode, other C.O. line in operator mode.
1. If the caller doesn’t know the extension number, he can inquiry the operator by dialing
“0”.
2. Outgoing Message must be record when setting this mode.
3.4.2 Operator Busy Process
Format: 1540# Operator busy waiting, this is the default setting.
1541#
Operator busy ringing the set extension.
Description: when many C.O. lines calling in, the operator just have one or two
communication lines, so some C.O.line only waiting ; but this setting can allow
the C.O.line calling ring the set extension directly and will not lose any calling.
3.4.3 Setting Operator Mode for C.O. line
Format:
1 1 #:
Description: Allows all the C.O. lines in Operator mode. In this mode, the operator extensions
and other ringing extensions will ring when anincoming call is received.
Format:
1 1 M#:
Explanation: M: C.O. line No.1-No.4
Description: allows the No.M C.O. line in Operator mode.
Example: Set C.O. line 1 and 3 in operator mode, other C.O. line in Auto-attendant mode.
3.4.4 Syst em CRBT Setting
Format:
167#
disable system CRBT
1670# enable system CRBT, C.O. line calling play OGM and ring the operator
directly.
1676# enable system CRBT, C.O. line calling play OGM and ring the extension
directly.
3.5 OGM Recording/Monitoring (For CS/TS Series)
3.5.1 OGM Recording
Format: 1 2 #
P13
Description: Used to record an outgoing message for Direct Inward System
Access (DISA).
3.5.2 OGM Monitoring
Format: 1 3 #
Description: Play and monitor the recorded OGM.
3.5.3 System Music Monitoring
Format: 14 #
Description: Perform the music on holding melody or test the quality of telephone unit.
3.6 OGM Recording/Monitor
Recording/Monitorii ng (For CS+/TS+ Series)
ee paragraph mode
3.6.1 OGM Recording and setting to thr
thre
Format:
1 2M #
Explanation: M=1,2,3 the paragraph of the OGM
Description: Used to record an outgoing message for Direct Inward System Access(DISA).
OGM 1 recording (8 seconds), this is the first OGM, usually it is for company greeting, for
example, you may record ”This is ABC company, Pls dial extension number or dial “0” for
operator. Thanks you for calling.”
OGM 2 recording (6 seconds), this is the second OGM, usually it is for C.O. line dial
extension and this extension is busy, if you want to transfer this calling to other extension,
you may record “Sorry! This extension is busy. Pls dial other extension number or dial “0”
for operator.”
OGM 3 recording (6 seconds), this is the third OGM, usually it is for C.O. line dial extension
and this extension no answer, you may record “Sorry! This extension do not answer, Pls
dial other extension number or dial “0” for operator.”
Example: Recording the first pieces OGM
1. when the system use two OGM ,you will record the same contents into two OGM,that
means
each pragraphs recording of two OGM is same .
2.The new message will overwrite the old one;
3. Please use high quality telephone to ensure high quality of recording;
4. If the caller dials a number before the system finishes playing the message, the
system will terminate playing the message, waiting for the caller to complete dialing;
P14
5. The caller will be connected to operator if he dial 0 first for inquiry;
3.6.2 Monitoring the recorded OGM and setting to three paragraph mode
Format:
1 3M #
Explanation: M=1,2,3 the paragraph of the OGM
Description: Confirms the recorded message in the OGM recording program, you can check if the
recording is satisfied or not, if not, you can record again.
Example: monitoring the OGM 2
when the system use two OGM ,you will hearing the first OGM’s contents(the second
OGM is same )
3.6.3 One paragraph OGM Mode
Format:: 1 2 0 0 #
Description: to recording one paragraph OGM(20s total)
Format:: 1 3 0 0 #
Description: to play and minitor one paragraph OGM(20s)
: 1. After performed above two commands(1200# or 1300#), system will change to one
OGM 20
seconds automatically.
2. After performed 12M#、13M# two commands, system will change to 3 OGM 20
seconds
automatically.
3. The OGM mode will be kept after power off.
3.7 Auto-attendant Mode Setting
w er Process
3.7.1 No Ans
Answ
Format: 160 #
this is default setting
Description: In auto-attendant mode, if the C.O. line doesn't dial the extension number over 5
seconds or more after hearing the OGM, then the C.O. line will be cut off.
Format: 161 # or 1610#
Description: In auto-attendant mode, if the C.O. line doesn't dial the extension number over 5
seconds or more after hearing the OGM, then the C.O. line will be transferred to
Operator.
Format: 1616#
Description: In auto-attendant mode, if the C.O. line doesn't dial the extension number over 5
P15
seconds or more after hearing the OGM, then the C.O. line will be transferred to
ringing extension.
3.7.2 Extension Busy Process
Format: 165#
Description: when the extension line busy, the line break; this is the default setting.
Format: 1650#
Description: when the extension line busy, the call transferred to operator.
Format: 1656#
Description: when the extension line busy, the call transferred to operator ring extension.
Above setting will be in effect with single OGM of the operator.
Format: 1655#
Description: when the extension line busy, prompt sound to the extension
This setiing will be in effect with single or multiple OGM.
w er Process
3.7.3 No Ans
Answ
Format: 166#
Description: when the extension line busy, the line break; this is the default setting.
Format: 1660#
Description: when the extension line busy, the call transferred to operator.
Format: 1666#
Description: when the extension line busy, the call transferred to operator ring extension.
3.8 Operator Setting
3.8.1 Operator Setting
Format:
15N #
Explanation: N: the Ext. line No., N=01-16
Description: To assign any Ext as the operator. In the default setting, EXT602 is the operator.
Example: Setting Ext.12 as operator
aling Operator
3.8.2 Fast Di
Dia
Format: 1520# system fast dialing operator is effective, this is the default setting.
1521#system fast dialing operator is not effective.
3.9 Operator Attendant Ringing Setting
3.9.1 Ringing mode w hen all the ringing extensions is busy
Format:
18 8 0#
Description: While the C.O.line come in, and all the ringing extensions assigned to C.O.line is
P16
busy , the system will send waiting call beep to the ringing extensions for every
five seconds, these extensions is assigned to the C.O.line
Format:
18 8 1#
Description: While the C.O.line come in,and all the ringing extensions assigned to C.O.line is
busy,instead of sending the waiting call beep, the system will find the first idle
extension begin from Ext. 601 to Ext. 696 in sequence then ringing it.
These setting will take effect only when the system in operator mode
3.9.2 Ringing Extensions Assignment/ to Cancel in Day mode
Format:
3MN0#
Explanation: M: the C.O. line No. M=1 – 4; N: the Ext. line No. N= 01 - 16
Description: In operator mode when calling of No.M C.O. line come in, Exts N will ring at the
same time.
Default setting: Only Ext 601, 602 will ring.
Format:
3MN1#
Description: Disable Exts N ring when calling of No.M C.O. line come in.
Format:
3M#
Description: Disable all Exts ring when calling of No.M C.O. line come in.
Example: Setting 606 and 615 ringing when the C.O. line 2 comes in.
1. This function must be in Operator Mode.
2. This programming only for C.O. line Incoming call. The extension which is not set ringing will
ring under Intercom Calling, Call Transfer.
3. This function is one way to set some extensions for not disturbed.
3.10 Ex
Extts. Dialing-out Mode
Format:
21#:
Description: Indirect-Dialing-Out mode for all the Exts(dialing 9 for outgoing).
Format:
2N1#
Explanation: N: the Ext. line No., N = 01 - 16
Description: Indirect-Dialing-Out mode for Ext. N (dialing 9 for outgoing).
Example: Set Indirect-Dialing-Out mode for Ext.15
P17
In default setting, all extension are in Indirect-Dialing-Out mode.
Format: 20#
Description: set Direct-Dialing-Out mode for all the Exts.
Format: 2N0#
Explanation: N: the Ext. line No., N = 01 - 16
Description: set Direct-Dialing-Out mode for Ext.N.
Example: Set Direct-Dialing-Out mode for Ext.12
1. In Direct-Dialing-Out mode, extension make intercom call should dial *first, then dial
the extension number.
2. No need dial 9 before outgoing call.
3.
3.111 Calling Restriction Setting
11.1 Calling Time Restriction Setting
3.
3.1
Format: 6NTT#
Explanation: N: the EXT No. (N = 01 - 16)
TT: the time restriction duration (2 digits), should be in 01-99 minutes.
Description: set the Ext N outgoing call duration to within TT minutes. This function can only
limit the time of exterior call.
Example: Set Ext.611 outgoing call duration to 8 minutes
Format: 6N00#
Explanation: N : the EXT No. (N = 01 - 16)
Description: Clear the Ext N outgoing call duration restriction.
Example: Clear the Ext.611 outgoing call duration restriction.
11.2 Calling Restriction-Class Setting
3.
3.1
Format:
40 L#:
Explanation: L: class number, L= 0 - 6
Description: Assign dialing-out class L for all Exts.
L=1: no any restriction
L=2: call out with restriction of International long-distance dialing
L=3: call out with restriction of domestic long-distance dialing
P18
L=4: call out with restriction initial of item A.
L=5: call out with restriction initial of item B.
L=6: only for intercom call
L=0: only for some special calling number Example:
Assign the calling class to be 3 for all extensions.
1. In
default setting, the class for all extensions is 2
2. This command enables a user to set class restriction on extensions in a fast and
convenient way, especially when most extensions have the same class.
For example, if you want set extension 603 to class 3 and extension 608 to class 4,and
the rest extensions to class 5, then you can set the restriction rank to be 5 for all
extensions and change the restriction class to 3 for extension 603 and 4 for 608
Format:
40 N L#
Explanation: N: the Ext. line No., N = 01 - 16
L : class number, L= 0 - 6
Description: Assign dialing-out class L for certain Ext. N
Example: Assign class 3 for ext.606
11.3 Calling Restriction Item
3.
3.1
‹ Calling Restriction Item A
Format: 4 1 Q ABCD#
Explanation: ABCD: the initial digits of the calling number to be locked, it can be from 1-digit
to 4-digits, it should be ended with # if less than 4-digits.
Q --- The group series from 01 to 16.
Description: to restrict the call-out number starting with ABCD
Example: Ext.608 is be assigned dialing-out class 4, now you want Ext.608 can’t dial the
numbers with initial digits – 573,168
1. Item A can lock 16 groups of initial digits.
2. Restrict Item A only work for dialing-out class 4.
Format: 41 Q #
Explanation: Q: The group series from 01 to 16.
Description: to clear the call-out restriction of certain numbers of group Q.
Example: you want to clear the call-out restriction of certain numbers with initial digits—573 of
group 01,
P19
Format:
41 #
Description: to clear all the call-out restriction of certain numbers of item A
‹ Calling Restriction Item B
Format: 4 2 Q ABCD#
Explanation: ABCD: the initial digits of the calling number to be locked, it can be from 1-digit
to 4-digits, it should be ended with # if less than 4-digits.
Q --- The group series from 01 to 16.
Description: to restrict the call-out number starting with ABCD
Example: Ext.609 is be assigned dialing-out class 5, now you want Ext.609 can’t dial the
numbers with initial digits – 575,161
1. Item B can lock 16 groups of initial digits.
2. Restrict Item B only works for dialing-out class 5.
Format: 42 Q #
Explanation: Q: The group series from 01 to 16.
Description: to clear the call-out restriction of certain numbers of group Q.
Format: 4 2 #
Description: to clear all the call-out restriction of certain numbers of item B
11.4 Assign Special Calling-out Number
3.
3.1
Format: 4 3 P ABCD#
Explanation: ABCD: the initial digits of the calling number to be locked, it can be from 1-digit
to 4-digits, it should be ended with # if less than 4-digits.
P --- The group series from 01 to 16.
Description : Permit to dial the phone numbers starting with <ABCD> only.
Example: Ext.610 is be assigned dialing-out class 0,now you want Ext.610 can dial the
numbers with initial digits – 0592,179
1. 16 groups of initial digits can be set.
2. This function only work for dialing-out class 0.
Format: 43P #
Explanation: P: The group series from 01 to 16.
P20
Description: to cancel the permission of certain calling-out numbers of group P
Format: 4 3 #
Description: to cancel all the permission of special calling-out numbers.
3.12 Ex
Extts. Using C.O. Lines Access
Format: 7M#
Explanation: M: C.O. line No, M = 1 - 4
Description: This function allows Every Exts. can use C.O line M.
Example: Allow every exts. can use C.O. line 3
This function is for the outgoing call and can’t change the function of C.O line ringing
assignment.
Format: 7MN0#
Explanation: M: C.O. line No, M = 1 - 4 N: Ext. No, N = 01 - 16
Description: This function assigns the extensions N outgoing to use the certain C.O. line
(M).
Example: Allow Ext.606 can use C.O. line 3
Format: 7MN1#
Explanation: M: C.O. line No, M = 1 – 4 ;
N: Ext. No, N = 01 - 16
Description: This function restrict the Ext. N to use C.O. line M
Example: Restrict Ext.608 can use C.O. line 2
3.13 Flexible co ding
Format: 9000#
Description: return to the Exts number of the default setting, that is: from 601 to 602
603… 616… 632 one by one, etc.
Format: 9Nabcd#
Explanation: N : the extension series number, N = 01 - 16,
abcd: the new number, 1 to 4 digit number, if new Ext number not exceeding to
4-digit number, press # in the end.
Description: Change old Ext number to new Ext number “abcd”
Example: Change Ext 606 to 806
P21
1. The new numbers range from 1-8999; all extensions numbers can not be in
duplicate.
2. The number can’t begin with 0 and 9,
3. The length (digits) of new number must follow the extension No.1; it must be
emphasized that if the length (digits) of new number changed, all the extensions
must be reset after setting extension No.1. All the new numbers should be equal
digits, and not in duplicate.
For example, to set the extension’s number to 4-digit number (8001-8032),the user
should dial 9018001# at first ,then dial 9028002#,9038003#…one by one, up to
8328032.
nging/
Transfer/Reservati
on time
3.14 Ri
Rin
ging/T
ransfer/Reservatio
3.14.1 Internal Call Ri nging Ti me
Format: 494TT#
Description: TT=01-99 (seconds), 0 means not stop ringing, default setting is 20 seconds; this
time must be more than the transfer time and extensions call busy time.
3.14.2 Operator Dialing/
Transfer Ringing Time
Dialing/T
Format: 496TT#
Description: TT=01-99 (seconds), default setting is 25 seconds; this time means the ringing
time if the extension not set transfer.
Note: this time must be more than no answer ringing time.
w er Transfer Ti me
3.14.3 No Ans
Answ
Format: 184TT#
Description: TT=01-99 (seconds), default setting is 25 seconds;
Note: this time must be more than no answer ringing time.
on Ti me
3.14.4 External Line Reservati
Reservatio
Format: 186TT#
Description: Unit: 10 seonds, TT=01-99; Default setting is 120 seconds, TT=12
3.15 Transfer Operation Parameter
3.15.1 External Transfer Mode
Format: 1530#
Description: After 3 busy tone, can connect the C.O.line in 5 seconds, this is the transfer
mode 1.
P22
Format: 1531#
Description: After 10 secs busy tone, can connect the C.O.line again without off-hook, this is
the transfer mode 2.
w er Ringing Back
3.15.2 External Transfer No Ans
Answ
Format: 162# External transfer no answer ringing back, call back the caller extension, this is
the default setting.
163# External transfer no answer ringing back, not call back the caller extension.
w er Transfer Po
wer-Do
w n Conservation
3.15.3 Off Place/Busy/No Ans
Answ
Pow
er-Dow
Format: 170#
171#
Power-down not conservation
Power-down conservation, this is the default setting
3.16 CID functions Setting (For CS+/TS+ Series)
3.16.1 Add digi
digitts for intercom CID
Format: 1 8 0 #
Description: Disable add digits for intercom Caller ID ,this is default setting.
Format: 1 8 0 kk #
Description: Add kk in intercom Caller ID number
Some CID telephone can't display the CID number less than 4 digits, so we must add more
digits for intercom CID.
3.16.2 Internal CID mode(transmit mode) setting
Format: 1 8 1 0 #
1 81 1 #
Format: 1 8 1 2 #
FSK mode(Default setting)
DTMF mode
FSK mode
1 8 13 #
DTMF mode
1 8 1 4#
Auto mode(Default setting)
The system can auto select C.O. line CID mode. Sometimes if system can’t display CID
correctly and you know the CID mode, you can use 1812# or 1813# to set CID mode
compulsively.
P23
Chap 4
Operating Instruction
4.1 Operator Attendant Mode
When the C.O. line coming call, the extension ringing, pick up the phone and can be in
conversation, if other extension want to hear the calling, can use the function of the pickup
transfer.
4.2 Auto-attendant Mode
This system basic use one paragraph of computer operator’s voice recording technology, it
will be played when extension busy and no answer. And also can record the company’s name,
extension number and some messages.
4.3 Off P lace/Busy/No Answer Transfer Programming
The system can set off-place/busy/no answer transfer programming by extensions 1-4
(601-604) and can easy management.
z
25# Cl
ear all the extensions
ansfer of off
sy
(*)#
(*)#2
Cle
extensions’’ tr
tra
off--place and bu
bus
z
(*)#
26# Cl
ear all the extensions
ansfer of off
(*)#2
Cle
extensions’’ tr
tra
off--place
z
26+N
+transfering exts.
(*)#
(*)#2
6+N+
z
26+
N#
(*)#
(*)#2
6+N
z
27#
(*)#
(*)#2
z
27+N
+transfering exts.
(*)#
(*)#2
7+N+
z
27+
N#
(*)#
(*)#2
7+N
Set N extension
extension’’s transfer of off-place
Clear N ex
exttension
ension’’s transfer of off
off--place
swer
Clear all the extensions
extensions’’ transfer of no an
ans
s we r
Set N extension
extension’’s transfer of no an
ans
swer
Clear N ex
exttension
ension’’s transfer of no an
ans
4.4 Dialing C.O. Lines
If extensions are direct dial-out mode:
Format: off-hook + tel no.
If extensions are indirect dial-out mode:
Format: off-hook + 9 + tel no.
4.5 Booking C.O.Lines
Format: off-hook + (*)# 0 + on-hook
Description: when the CO lines are busy but urgently to call, the system will prompt the extension
when CO line available.
4.6 Outward dialing by an exclusive line
Format: [*] # 1 M
Explanation: M: C.O. line port number M=01-16
P24
Description: In some occasion, the user may place an outward call by an exclusive line and we
definite it as Choosing line dialing.
Example: At indirect-dialing-out mode, the user want call out by C.O. line 5 to dial *57*8622373#
1、If you want to outward from C.O.2 、C.O.3、…C.O.line 9(M=2,9) you can only dial
#12、#13 …#19 ,one digit M, And if you want to outward from C.O.line 1,you can dial #1 1 and
waitting two seconds .that means if you want to outward from C.O.10 、C.O.11、…C.O.line
16(M=10,16) ,you should dial the second digit of M within two seconds after you dial # 1
1,otherwise the system will select C.O.line 1.
2、when the user want to dial some special number in the C.O.line such as * or # ,then he
can use this operation;
3、when the user want to check the C.O.line connectting is ok, ,then he can use this
operation;
4、Allows you to redial the last telephone number
g oing Call Transfer
4.7 Out
Outg
The details operation, please see the C.O line transfer. This function just can take effect after
several seconds for dialing the CO line last number.
4.8 Coming Call Pickup
4.8.1 Call Pickup Ex
Exttension
Format: (*) # 3 + ext.
Description: Not ringing ext. can pickup the calling for ringring ext.(including ext. and CO line)
4.8.2 General Call Pi ckup
Format: (*) #
9 (General call pickup)
Suggest don’t use this function when much calling, otherwise easy pickup not willing call.
nal Call)
4.9 Call Transfer (Exter
(Extern
Format: Pat the hook (or press the FLASH button) then dial the Ext. number..
Description: 1. Allows you to transfer an incoming call to another Ext.
2. The Flash time can be set.
3、In the process of the tranfer,the C.O.line will hear holding music(refer 4.9、5.2).
4、when the Ext. number is 0 ,then you will tranfer to the operator.
Example: Ext.607 is talking to C.O. line and want to transfer the C.O. line to Ext.618. Then Ext.605
can transfer the incoming call to Ext .618 by by patting the hook ( or pressing the FLASH ) and
P25
dialing 618.
There may be following 8 cases after a call is transferred from A to B:
1. A does not hang up and B picks up his handset .Then communication between A and B is
established while the outside caller is on hold (music on hold). Whoever hang up (A or B), the
system will transfer outside caller to the other.
2. A does not hang up and B does not answer A within 25 seconds. Then A will restore the
connection with CO. line , and B will stop ringing.
3. A hangs up and B answer the call, B will answer the outside caller.
4. A hangs up and B does not answer the call within 25 seconds, call will be back to A and will ring
or cut off , if A never pick up the call in 25 seconds or A is busy , the system will cut off.
5. After A pat the hook then hear the error massage, that means the system is busy, A can
continue to pat the hook until the error massage is disappear.
6. A make invalid operation or B is busy, After System indicate with “du-du-du” for 10 seconds then
A should pat the hook to restore the call and repeat the tranfer operation.
7. A hangs up and B does not pick up. A pick up again and press: # 9 (If the Ext is at
direct-dialing-out mode, you should input: *# 9), then A will restore the connection with C.O. line.
8. The EXT A, which transfer the call pat the hook , has 10 seconds to dial the Ext. number.
Otherwise the Ext A will be silence, and system will continue to holding the C.O.line ,and C.O.
line hear holding music; if the ext want back to the call, he can pat the hook.this can let the user to
holding the C.O. line freely.
4.10 Three Way Conference
Format: Pat the hook (or press the FLASH button) dial * and the Ext .number
Description: Allows you to add a third party to a two-party conversation and make a three-party
conference. You can have only two Ext. with one C.O. line.
Example: Ext. 605 is talking to C.O. line caller and he want to transfer the call to Ext.617. then
Ext.605, Ext.617 and C.O. line can talk at the same time.
1.There may be following 2 cases after a call is transferred from A to B.
a. A does not hang up and B picks up his handset. Then communication amount A B and
C.O. line is established, whoever hang up (A or B), the system will transfer outside call to another
one.
b. A does not hang up and B does not answer A within 25 seconds. If Ext. B does not answer
A within 25 seconds, then A will restore the connection with C.O. line, and B will stop ringing.
2. The Ext, which transfer the call , has 10 seconds to dial the Ext number required
otherwise you should pat the hook to return the incoming call to repeat the operation.
P26
3. If dialing wrong number, you can pat the hook to return the incoming call.
4.
on
4.111 C.O. line Reservati
Reservatio
Format:
Pat the hook (or press the FLASH button) dial # # (Reservation) while talking with
C.O.line.
Description: Extension N is talking with C.O. line A and at this time B calling in , Extension N Pat
the hook and press # # to make A in state of caller On Holding( A is hearing music
while waiting ). At this moment, Extension N can make Call Pick Up, Call Transfer,
Dialing Out etc.···
1.The default setting of caller on holding’s duration time is in 270 sec.
2.A extension can holding several calling,
3.You also can pat the hook (not dialing) to hold the C.O.line you are talking with ,refer
5.6 when you pat the hook again,you can restore the C.O.line ,but if you hang up ,the
C.O.line will cut off.
4.12 C.O. line tr
ansfer to C.O. line
tra
Description: Ext. N is talking with the C.O. line A, at this moment Ext. N holding this C.O. line
A (pat the hook and input # #), then Ext .N can hear the internal dialing tone,
now he can dial ‘9’ to C.O. line C and use it to call desired number ( at this
moment if invalid operation or line is busy ,he can hang up and dial again) ,after
Ext. N is talking with C.O. line C, Ext. N can operate the follows to make two
function:
1.
ces (2C.O. line and 1 Exts
3 par
partty-Conferen
Conferenc
Exts)): Ext. N pats the hook and input # *Then
communication amount Ext. N, C.O. line A and C.O. line C is established, the 3-party can
talk, if Ext. N hang up, the C.O. line A and C.O. line C will be cut off, the talking will be
ended.
2.
C.O. line transfer to C.O. line : Ext. N pat the hook and input # 6 ,and Then
communication amount Ext. N ,C.O. line A and C.O. line C is established ,The 3-party
can talk ,but now Ext. N can hang up ,and C.O. line A can keep talking with C.O. line C;
and system will indicate C.O.line A and C.O. line C every 2 mins, if C.O.line A and
C.O.line C input *# within 10secs, the system will be continue to connect the 2 mins,
otherwise the conversation will be end off and then release the C.O.line A and C.O. line
C.
If input ** at that time, the system will hand up the C.O.line and end off this operation.
4.13 Fast Reservation Transfer
Ext. can call pickup during the C.O. line conversation, together with the function of C.O.line
prompt and then can carry out the general phone function.
P27
Format: during the conversation, pat the hook and then press # 9
Description: Normal phone pat the hook and then press #9 transfer any incoming
C.O.line(reservation original conversation), and also can transfer to pickup doorphone calling
(note: C.O.line ringing first, doorphone second and internal reservation third). Keyphone should
press “transfer” button and then press #9.
4.14 Call Switch (call pick during conversation)
While an Ext. talking with a CO. line , an Ext. or a doorphone, the other CO. line calling in or the
other doorphone call in and should ring this Ext., you will hear prompts beep tone( the beep for
doorphone calling and CO. line calling is different). Then you can:
Operation1: for normal phone, Pat the hook (or press the FLASH button), then you will hear dial
tone, press “# 9” to switch another Co.line, also you can switch to receive the call
from door phone. The first conversation now is be holded(for CO.line talking ,the
holding time can be set in chapter 4, but for the conversion with doorphone will be
ended ), when you talking with the second call,you also can Pat the hook and press
# 9 to take back the first holding call.
Note:
1、 when there are some calling at the same time ,CO.line calling is the prior grade to be switch,
and door phone calling is second , the Co. line hold is in the third grade.
2、 For key phone you should press transfer key instead of Pat the hook.
3、 Answer incoming waiting call by # 9 and take back the first one by # 9 again can be
repeatable as long as the you like for CO.line, but for doorphone you can only switch one
time.
4、 The waiting incoming call beep(prompt beep) are different for the door phone call and the
CO.line call ; The doorphone calling prompt beep is two beep(du du ),and the CO.line
calling prompt beep is three brief beep(du du du)
.
Operation2: for normal phone, Press # continue some time (or Pat the hook) ;then press “#2” to
switch to a doorphone call(when you hear two prompt beep).
4.15 Int
ercom Calling
Inte
Format: * + Ext number
Description: Make internal call from Ext. with direct-dialing-out mode.
Format: Dial the Ext. number directly.
1、Intercom calling is free of charge,
2、Allow you to redial
4.16 Dialing Operator
Format: (*)+0
P28
Description: This function easy dial operator.
1. If the ext. in indirect mode, not need press (*)
2. This function can be canceled.
4.17 Inquiry Functions (Automatic Reporting)
4.17.1 Reporting of Physics Number
Format: [*] # 60
Description: During installing and testing of the system, it is very convenient to find the Ext number.
The system use “du” for this purpose.
Example: After input # 61 on Ext. 626 you may you may hear 6 continuous “du” , and after 1.5
seconds you will hear 2 “du”; finally you will hear 6 “du” , at about 1.5 seconds later , that
mean the Ext number is 626
10 continuous du stands for “0”
4.17.2 Automatic reporting of Ext number
Format: [*] # 61
Description: During installing and testing of the system, it is very convenient to find the Ext number.
The system use “du” for this purpose.
Example: After input # 61 on Ext. 626 you may you may hear 6 continuous “du” , and after 1.5
seconds you will hear 2 “du”; finally you will hear 6 “du” , at about 1.5 seconds later , that
mean the Ext number is 626
10 continuous du stands for “0”
4.18 Priority Access and Monitoring
Format:
#7 M
Explanation: M: the C.O. line port number. M = 1 - 4
Description: Establish direct connection with C.O. line regardless whether or not this line is
occupied. This feature ensures the director or owner of a company monitor the
C.O. line communication.
Example: Priority access to C.O. line 3.
1. Only Ext.601 has priority access
2. If the Ext is at Direct-Dialing-Out mode, you should input: * # 7 M.
3. The monitor is responsible for the legal issues resulting from the operation.
P29
4.19 Call Forwarding
Format: # 81 abcd then hang up
Explanation: <abcd> is desired Ext number. This is at Indirect-Dialing-Out mode. Description:
Allows the Ext user to transfer incoming calls automatically to desired Ext. Example: The
user of ext. 605 wants to go to 607 for work then he can forward all the
incoming calls of 605 to 607
Format: # 81 # then hang up
Description: Clear setting call forwarding directly of this extension.
1. In Direct-Dialing-Out mode, you should set with * # 81 abcd and clear with * # 81#.
2. Pick up the handset of Ext with Call Forwarding function you will hear nothing and
can’t do any operating, you must hang up to cancel the function first
3. When power failure, this setting will not be stored.
4.20 Call Forwarding When Ext is Busy or Nobody Available
Format:
# 82 abcd then hang up
Explanation: <abcd> is desired Ext number. This is at Indirect-Dialing-Out mode.
Description: If a Ext is busy or nobody available after 25 seconds, the incoming call will be
transferred to desired Ext. automatically.
Example: When the ext. 605 is busy or no answer, then he wants to transfer the incoming
calls to the operator 602
Format: # 82 # then hang up
Description: Clear setting of call forwarding when Ext is busy or nobody available after 25
seconds
1. At Direct-Dialing-Out mode, you should set with * # 82 abcd and clear with * # 82#.
2. When power failure, this setting will not be stored.
u rb Setti
ng
4.21 Don
Don’’t Dist
Distu
Settin
Format:
# 83
Description: If “Don’t Disturb” is set for the extension, then this extension will not ring.
If the Ext is at Direct-Dialing-Out mode, you should input: * # 83
ension
4.22 Call All Ext
Exte
Format:
# 88
P30
If the Ext is at Direct-Dialing-Out mode, you should input: * # 88
4.23 Clear Extension Function Setting
Format: [*] # 8 0
Description: This command will clear all function that extension set, such as No
disturbing/Call divert/Call forwarding/C.O. line booking/Alarm clock etc. This
command has no effect to other extension.
Appendix I
Maintenance & Troubleshooting
1.Outgoing calls can
can’’t be made
1). C.O. line is set to special Extension;
2). Extension hangs up improperly;
3). CPU and internal data is disorder caused by unstable power.
4). Call restriction class is 6.
2.Ou
2.Outtside calls can
can’’t dial in
1). The conjunction of C.O. line loose;
2). C.O. line was connected to other equipment;
3). No message recording at auto-operator mode.
3.Intercom can
can’’t be made
1). Extension hangs up improperly;
2). Extension number wrong.
KDOWN
BREA
BREAK
Running
malfunction
light
No sound from e xtension
Cacophony
Bad tone
CAUSE
SOLUTION
Check the power socket and Power
supply
Power off
Disconnected
wiring
malfunction of telephone.
or
Reconnect the wiring or try to remove
the telephone’s failure
Bad connection
Screw down the joint
The distributing of line is not
reasonable
Leave telephone from the disturbing
source
Mix using
telephones
Use the standard telephones
of
non-standard
P31
Devoid function
telephone display
incoming
Write application to telecommunication
office
Wrong setting of No-disturbing
and it status.
Rescind the No-disturbing and set
incoming telephone display
Exterior line disconnected
Connect to the exterior line
Dial-out malfunction
Exterior line is not connected well
Check whether the line is
connected well
Limited calling time
Time limited
Rescind the limit
Wrong coding
Check the programming extension and
use the right code
Others
Refer to professional
No incoming
telephone display
Cannot program
telephone
Others
Appendix II
the
of
Glossary
Programming extension-----------------Extension No.601, 602, 603, 604
N-----------------------------------------------Series number of the extensions (01-32 with corresponding input ports
601-632) (two digits)
abcd------------------------------------------Number of the extension(1-8999,except for the digits with the first digit of 0 or
9,outward code of special trunk line, in equal length)is accordance with N.
M-----------------------------------------------Series number of the exterior line (No.1-8 with corresponding input ports of
Line 1- 8)
P-----------------------------------------------Licensed Group Number (01-16)
Q-----------------------------------------------First-digit restrict group number (01-16)
ABCD-----------------------------------------Licensed or restricted number of first 1-4 digits
EFGH----------------- -----------------------4 digits of programming password
L-----------------------------------------------Service grade(Grade of private passwords or outgoing call),grade 0-6
TT----------------------------------------------Time in minute for call duration control, ranges from (01 to 99)
F------------------------------------------------Flash time class.
YYMMDD-------------------------------------YY: Year, two-digit number, from 00 to 99, MM: Month, two-digit number,
from 01 to 12, DD: Date, two-digit number, from 01 to 31
hhtt----------------------------------------------hh: hour, two-digit number, from 00 to 23, tt: minute, two-digit number, from
00 to 59
P32
Appendix III
Default Settings
• The system programming password: 0000
• Operating mode: All C.O. line in Operator mode
• Dialing out mode: Indirect-Dialing-Out mode, dialing “9” for outgoing
• All C.O. lines are ungrouped
• Operator: Ext 602
• Ring Ext.: Ext 601 and Ext 602
• Extension service class assignment: 2
• Time Restriction: No
• Flash time: 1.0s
• Outgoing Exts. Assign to Certain C.O. lines: No
• Original EXT number: 601 to 616
• Restrict Item A / Item B: No setting
• Special Calling-out Number: No setting
P33
Programming & Operation Instruction
Appendix IV
1. Index of Basic Operation
Description
Indirect-Dialing-Out mode
Direct –dialing-out mode
Command
1
Outward Dialing
9 + desired number
desired number
2
Outward Dialing by a Exclusive Line
#1M
*#1M
4
Intercom calling
Ext number
*+Ext number
5
Call Transfer
Pat hook + Ext number
6
Secretary Function
Pat hook + Ext number
7
3-Party Conference Call
Pat hook + *
8
Caller on holding
Pat hook + ##
9
Call Pickup
#9
10
Call Forwarding Directly
11
12
+ Ext
*#9
setting:
#81 +Ext number
*#81+Ext Number
clear :
#81#
*#81#
Call Forwarding when Ext is busy
Setting:
#82 +Ext number
*#82+Ext number
or nobody available
clear :
Automatically Call back Busy- come
#0
*#0
# 60
* # 60
# 62
* # 62
#82#
*#82#
on
13
Automatic Reporting of Ext
number (voice)
14
Reporting of Ext number for caller
ID phone
15
Connect with Operator Directly
0
*0
16
Priority Access and Mo nitoring
#7M
*#7M
(only Ext.601)
17
C.O. line transfer to C.O. line
Pat hook + #* (3-Party conference)
Pat hook + #9
(C.O. line transfer to C.O. line)
18
Monitor the chord melody music
#67KK#
*#67KK#
19
Setting Don't disturb
#83
*#83
20
Use broadcast function
#88
*#88
P34
2. Index of system programming
No.
Description
Command
1
Start the System Programming
(*) # * EFGH
2
Change the System Password
09 EFGH #
3
Return to Default Setting
0000 #
4
Enable all C.O. lines
0600 #
5
Disable all C.O. lines
0610 #
6
Enable No. M C.O. line
060M #
7
All C.O. lines in Auto-attendant Mode
8
C.O. line M in Auto-attendant Mode
9
All C.O. lines in Operator Mode
10 #
10 M #
11 #
10
C.O. line M in Operator Mode
11 M #
11
OGM
Recording
12 #
12
OGM
Play
13 #
13
Monitor Holding Music
14
Setting Operator
15 N #
15
System option for no dialing in The DISA----Cut off C.O. line
160 #
16
System option for no dialing in The DISA----Transfer to Operator
161 #
17
Disable add digits for intercom CID
180 #
18
Add KK in intercom CID number
19
Set C.O. line CID mode to FSK (optional)
1812 #
20
Set C.O. line CID mode to DTMF(optional)
1813 #
21
Set C.O. line CID mode to Auto Detect(optional)
1814 #
22
Direct-Dialing-Out mode for Ext.N
2 N0#
23
Indirect-Dialing-Out mode for Ext.N
24
Direct-Dialing-Out mode for all the Exts.
20 #
25
Indirect-Dialing-Out mode for all the Exts
21 #
26
Enable Exts N ring When calling of No.M C.O. line come in
3MN0 #
27
Disable Exts N ring When calling of No.M C.O. line come in
3MN1 #
28
Disable all Exts
29
Assign dialing-out class L for certain Ext. N
30
Assign dialing-out class L for all Exts
31
Restrict the Certain Numbers from item A
32
To cancel the restriction of item A
41 #
33
To clear group Q of restiction item A
41Q#
14 #
180 KK #
ring When calling of No.M C.O. line come in
P35
2N1 #
3M #
40NL #
40L #
41 Q ABCD #
34
Restrict the Certain Numbers from item B
35
To cancel the restriction of item B
42 #
36
To clear group Q of restiction item B
42Q#
37
Assign Special Calling-out Numbers
43 P ABCD #
38
To cancel the permission of special calling-out numbers
39
To cancel group P of special calling-out numbers.
40
Time Restrict Setting
6N TT #
41
To cancel time restrict
6N00 #
42
assign the extensions N outgoing to use the certain C.O. line (M).
7MN0 #
43
To restrict the EXT.N to use C.O. line M.
7MN1 #
44
Allow every Exts. to use C.O. line M
45
The Exts number return to the default setting
46
To change the Ext.N to new number "abcd"
P36
42 Q ABCD #
43 #
43 P #
7M #
9000 #
9Nabcd #
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement