Crib + Changer Combo
Crib + Changer Combo (5591) - Assembly and Operation Manual
Congratulations on purchasing a MDB Family product. This product will provide many years of service if
you adhere to the following guidelines for assembly, maintenance and operation. This product is for
residential use only. Any institutional use is strictly prohibited.
Please be sure to follow the instructions for proper assembly. Use a Phillips head screwdriver for assembling the crib in addition to the Allen wrench included in the hardware box. Do not use power screwdrivers.
All of our products are made from natural woods. Please understand that natural woods have color
variations which are the result of nature and not defects in workmanship.
DO NOT SUBSTITUTE PARTS. ALL MODELS HAVE THE SAME QUANTITY OF PARTS AND HARDWARE. YOUR MODEL MAY LOOK DIFFERENT FROM THE ONE ILLUSTRATED DUE TO STYLISTIC
VARIATIONS.
!
WARNING!
READ ALL INSTRUCTIONS BEFORE USE OF THE CHANGING TABLE, ADD-ON
CHANGING UNIT, OR CONTOURED CHANGING PAD.
!!PLEASE READ!!
Assembly of this furniture is easier with two people. Assemble furniture on debris free carpets or on the enclosed
foam sheets to prevent scratching of finish. Using any power tools to assemble this furniture may potentially strip
the wood. DO NOT OVERTIGHTEN SCREWS. DO NOT USE THE CHANGING TABLE IF IT IS DAMAGED OR
BROKEN.
* The crib can later be converted
into a toddler bed or a full-size
bed. To convert to a toddler bed,
turn to page 16. To convert to a
full-size bed, turn to page 17.
Revised 08JUL2011
page 1
PARTS
B. Front Panel
A. Back Panel
C. Right Side Panel
D. Left Side Panel
E. Center Panel
F-1. Right
Back Post
H. Crib Top Panel X 2
K. Spring Frame
F-2. Left F-3. Back
Back Post
Post
L. Guardrail
P. Drawer
Back (3)
M. Drawer
Front (3)
N. Right Drawer
Panel (3)
G-1. Right
Front Post
Q. Drawer
Bottom
Board (3)
G-2. Left G-3. Front
Front Post
Post
R. Dresser Back
Top Panel
O. Left Drawer
Panel (3)
page 2
S. Dresser Back
Panel
X. Dresser Bottom
Bar (2)
T. Dresser Front
Top Bar
U. Dresser Center
Bar (2)
AA-2. Dresser
Shelf (with pre-drilled
screw holes)
AA-1. Dresser
Shelf
Z. Dresser
Top Board
Y. Dresser
Center Board
V. Dresser Middle
Bar (2)
W. Dresser Top
Bar
Tools Needed
(not included)
BB. Pad
Phillips
screwdriver
HARDWARE
H1. 3 -1/2” Allen Head Bolt (8)
H3. 2 -1/2” Allen Head Bolt (16)
H7. 1-1/4” Wood
Screw (24)
H2. 2 -3/4” Allen Head Bolt (2)
H4. 1 -3/4” Allen Head Bolt (8)
H13. 1/2” Small Wood
Screw for Glides (36)
H9. 1” Metal Pin (20)
H15. Knob (3)
H5. 1” Allen
Head Bolt (4)
H6. Barrel
Nut (24)
H14. 1-1/8” Bolt
for Knob (3)
H16. Right Panel Glide (3)
H18. Left Panel Glide (3)
H17. Right Drawer Glide (3)
H19. Left Drawer Glide (3)
H20. Strap
H21. Wood
Screw (2)
H24. Allen
Wrench
H25. Lock
washer (38)
H26. Washer (4)
H27. 7/8" Wood
Screw (2)
GUARDRAIL HARDWARE
H22. 2” Allen Head Bolt (4)
H23. Lock washer (4)
page 3
STEP 1. Assemble all drawers
Q.
1B
1A
Dr
O. Left
Drawer
Panel
H7
aw
Bo er B
ard otto
m
H7
N. Right
Drawer
Panel
M.
1C
D
Fro rawe
nt r
H7
H7
P.
H7
Dr
aw
er
H7
Ba
ck
DO NOT OVERTIGHTEN.
H7
1D
H7
H19. Left
Drawer
Glide
1E
H13
H14
H17. Right
Drawer
Glide
H13
H13
H13
H13
H13
H15
page 4
H6
STEP 2. Attach posts to center panel
H25
H1
H6
H25
H2
F-1. Right
Back Post
H25
te
en
C
E.
H1
H25
l
ne
a
rP
G-1. Right
Front Post
H2
DO NOT OVERTIGHTEN.
STEP 3. Attach panel glides and metal pins to center and right side panel
H9
H13
H13
H9
H9
H9
H13
H13
H13
E.
H13
H13
H13
H13
H18
H13
ter
n
Ce
H18. Left Panel Glide
l
P
e
an
C.
Rig
ht
H13
H13
Sid
eP
an
el
H16. Right Panel Glide
H16
page 5
STEP 4. Attach dresser panels and
bars to right side panel
T
W
H25
H9
H6
X
H25
H9
H6
H3
H3
C. Right Side Panel
H6
H25
H4
R
S
X
H25
H9
H6
H4
H3
H25
H9
H25
H3
DO NOT OVERTIGHTEN.
STEP 5. Attach dresser bars to
right side panel
U
V
U
V
H9
H9
page 6
STEP 6. Attach dresser boards
to the dresser
Z.
Dr
es
se
rT
op
Bo
ard
r
sse rd
e
r
a
D
Y. er Bo
t
n
Ce
H3
STEP 7. Attach center panel to
the dresser
H4
H25
H25
E.
H3
H9
DO NOT OVERTIGHTEN.
Ce
nte
rP
el
H3
H4
H25
H6
H25
an
H25
H3
H9
H9
H25
H9
H6
H6
H9
H9
H6
page 7
H6
STEP 8. Attach posts to left side panel
H1
H25
H6
H6
H6
H1
H25
H1
H25
H6
H6
H1
eft
H25
H1
Pa
e
Sid
L
D.
F-2. Left
Back Post
l
ne
H25
G-2. Left
front post
H1
H25
DO NOT OVERTIGHTEN.
H25
H4
H3
STEP 9. Attach the crib top
panel and back panel
H25
H6
DO NOT OVERTIGHTEN.
D
.L
eft
Sid
l
ne
a
eP
H.
H3
Cr
ib
To
pP
an
el
H6
H25
A.
H4
H3
Ba
ck
Pa
ne
l
H25
H3
page 8
STEP 10. Attach spring frame
Swing out four hangers at corner of the spring frame (K) carefully. Attach spring frame FLAT SIDE UP.
Choose the height of the spring frame. Start at the highest level and adjust accordingly.
Bolt the spring frame (K) to legs using Allen head bolts (H5), washers (H26), lock washers (H25) and Allen
wrench (H24). As the child grows, it is important to lower the spring.
Make sure the spring frame is level.
H26
Do not overtighten.
K
H25
H5
n
pri
S
K.
e
am
r
gF
Make sure the mattress support frame is installed FLAT SIDE UP. Make sure the mattress
support frame is level when installing.
*As your child grows, it is important to lower the mattress support.
page 9
STEP 11. Attach the crib top
panel and front panel
H4
H3
H25
DO NOT OVERTIGHTEN.
H6
H25
H.
H6
Cr
ib
To
pP
H3
an
el
H25
H4
H25
B.
STEP 12. Place dresser shelves
into the dresser
H25
Fro
nt
Pa
H3
ne
l
H3
H25
AA-1
AA-2
H27
AA-2
H27
Fix the dresser shelf (with predrilled screw holes) (AA-2) using
two 7/8" wood screws (H27).
page 10
STEP 13. Slide drawers to the
dresser
STEP 14. Attach the strap
H21
H21 H20
H20
H21
H21
DO NOT OVERTIGHTEN.
page 11
STEP 15. Place the pad onto the changer
BB. Pad
KEEP THIS MANUAL IN A SAFE
PLACE FOR FUTURE REFERENCE.
The recommended maximum weight of
the occupant is 30 lbs on changing table.
Be sure to tighten the cross bar screws now that you have installed to the stationary side. Recheck all screws
and bolts to be sure they are fastened securely.
Before placing your mattress in the crib, you can make your own mattress protector by cutting the cardboard
packing insert to 27” x 51”. Place it on the spring frame under the mattress to extend the life of the mattress.
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4 INCHES (69CM)
BY 51 5/8 INCHES (131CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).
Please refer to the label (sample below) on the inside face
of the headboard. Record the model/ item number and serial
number of your crib, the name of the store where you made
the purchase, the date of purchase and the wood nish in
the box to the lower right.
WE WILL ASK YOU FOR YOUR SERIAL NUMBER FOR ALL
WARRANTY AND REPLACEMENT PART REQUESTS. PLEASE
REFER TO THE LAST PAGE OF THIS INSTRUCTION SHEET FOR
WARRANTY INFORMATION. KEEP THIS MANUAL FOR FUTURE
REFERENCE.
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27 1/4 INCHES (69CM) BY
51 5/8 INCHES (131CM) WITH A THICKNESS
NOT EXCEEDING 6 INCHES (15CM).
THIS PRODUCT CONFORMS TO THE
APPLICABLE REGULATIONS OF THE
CONSUMER PRODUCTS SAFETY COMMISSION.
www.themdbfamily.com
SAMPLE LABEL
Please read the Caution and Warning
Statements insert before using your crib.
page 12
WARNING:
Failure to follow these warnings and
the assembly instructions could result
in serious injury or death.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP THE MANUAL FOR FUTURE USE.
WARNING:
Parents should ensure a safe environment for the
child by checking regularly, before placing the
child in the product, that every component is
properly and securely in place.
• Do not use this crib if you cannot exactly follow the accompanying instructions.
• Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed
on their backs to sleep, unless otherwise advised by your physician.
• Strings can cause strangulation! Do not place items with a string around a
child’s neck, such as hood strings or pacifier cords. Do not place cords, straps,
or similar items that could become wound around the child’s neck in or near this
crib. Do not suspend strings over a crib or attach strings to toys.
• To help prevent strangulation tighten all fasteners. A child can trap parts of the
body or clothing on loose fasteners.
• DO NOT place a crib near a window where cords from blinds or drapes may
strangle a child. Do not place this crib near a window or a patio door where a
child could reach the cord of a blind or curtain and be strangled.
• When a child is able to pull to a standing position, set the mattress to the lowest
position and remove bumper pads, large toys and other objects that could serve
as steps for climbing out.
• Do not use this crib if the child is able to climb out unaided or is taller than
35 in. (89cm).
• Check this product for damaged hardware, loose joints, loose bolts or other
fasteners, missing parts or sharp edges before and after assembly and frequently
during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if
any parts are missing, damaged or broken. DO NOT substitute parts. Contact
MDB FAMILY for replacement parts and instructional literature if needed.
• DO NOT use a water mattress with this crib.
• For cribs equipped with teething rails, replace teething rail if damaged, cracked
or loose.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic films as mattress covers
because they can cause suffocation.
• Infants can suffocate in gaps between crib sides when used with a mattress
that is too small.
• Follow warnings on all products in a crib.
• Ensure that the sides are properly latched or locked in place when the crib is
occupied.
• The mattress used with this crib should not be more than 15cm thick and
should be of such length with width that the gap between the mattress and the
sides of the crib is no more than 3cm when the mattress is pushed into the
corner of the crib.
WARNING:
Please do NOT remove any wood screws
in the normal disassembly of the crib.
ONE YEAR LIMITED WARRANTY:
We will replace any missing parts at the time
of purchase or any defective item within a one
year period from the date of original purchase.
Please keep your receipt so that we may
process your warranty request. This warranty
only covers new units with original packaging
and ownership, and is not transferable. It does
not cover any used, secondhand or demo
models.
This warranty does not cover any damaged or
defective parts that result from installation and
assembly, normal wear and tear, abuse, negligence, improper use or alteration to the finish,
design, and hardware of the crib. The specific
legal rights of this warranty may vary from
state to state. Some states do not allow any
exclusion or limitation of incidental damages.
Some states do not allow limitation on how
long an implied warranty lasts.
Storage:
• Pine woods exchange moisture with the air adjusting to major changes in room temperature and
humidity. Therefore, it is best to place your furniture
away from heating or air-conditioning vents.
• Sunlight is not friendly to solid wood furniture and
prolonged direct exposure to harsh sunlight can
discolor the finish. Be careful not to place your furniture in direct sunlight for extended periods of time. As
with all your fine furniture, blot up spills immediately.
Care and Cleaning:
• Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild soap on
a soft rag. Rinse and dry thoroughly. If you ever
refinish this furniture, be sure to use only a non-toxic
finish specified for children’s products. If you choose
to refinish this furniture, the warranty will be voided.
Registering your product is even easier than
before. You can register your product on our
website at : www.themdbfamily.com
IF YOU WOULD LIKE TO ORDER
REPLACEMENT OR MISSING PARTS
PLEASE VISIT US AT:
WWW.THEMDBFAMILY.COM
OR YOU CAN CONTACT US BY MAIL:
MDB FAMILY
855 WASHINGTON BLVD.
MONTEBELLO, CA 90640
revised05MAY2011
WARNING!
FALL HAZARD
TO PREVENT DEATH OR SERIOUS
INJURY, ALWAYS KEEP CHILD WITHIN
ARM’S REACH.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING THIS
PRODUCT. KEEP THE MANUAL FOR FUTURE USE.
WARNING:
•Read all instructions before use of the changing table.
•Do not use changing table if it is damaged or broken.
•This product is not intended to be used as a changing
table without adult supervision. Use of the product
without this may result in death or serious injury to your
child from falling. Follow all instructions on attaching
and using the changing table.
•Only use the pad provided by MDB FAMILY .
•The maximum weight of the child for which the changing table is intended is 30 lbs.
•Stop using this changing table when the child is able to
sit up or roll over.
•As with all infant and baby furniture, it is important to
check fasteners, screws, and bolts periodically for tightness. Parents should ensure a safe environment for
their child by checking the furniture regularly before
placing the child in the product.
•When using this product, always secure the child with
the safety strip.
WARNING!
FALL HAZARD
To prevent death or
serious injury, always
keep child within arm’s
reach. Never leave child
unattended and always
use restraining system.
ONE YEAR LIMITED WARRANTY:
We will replace any missing parts at the
time of purchase or any defective item
within a one year period from the date of
original purchase. Please keep your receipt
so that we may process your warranty
request. This warranty only covers new
units with original packaging and ownership, and is not transferable. It does not
cover any used, secondhand or demo
models.
This warranty does not cover any damaged
or defective parts that result from installation and assembly, normal wear and tear,
abuse, negligence, improper use or alteration to the finish, design, and hardware of
the crib. The specific legal rights of this
warranty may vary from state to state.
Some states do not allow any exclusion or
limitation of incidental damages. Some
states do not allow limitation on how long
an implied warranty lasts.
Registering your product is even easier than
before. You can register your product on our
website at : www.themdbfamily.com
IF YOU WOULD LIKE TO ORDER
REPLACEMENT OR MISSING PARTS
PLEASE VISIT US AT:
WWW.THEMDBFAMILY.COM
OR YOU CAN CONTACT US BY MAIL:
MDB FAMILY
855 WASHINGTON BLVD.
MONTEBELLO, CA 90640
page 14
WARNING:
Restraint System
During the diaper changing process, be sure always to keep one hand on the baby to prevent the baby from falling off the
changing pad. Falling from the changing pad could cause severe injury or even death to the baby.
Step 1.
Place a baby on the pad with his/her bottom on the
top of the diaper. Safely secure the baby on the pad
with the safety straps and buckle on the pad. This
helps prevent the baby from falling off the pad,
which can result in severe injury or even death of
the baby.
Step 2.
Remove the dirty diaper from the baby.
Step 3.
Push the baby’s legs forward and create a cavity
under the baby’s bottom. Clean the baby.
Step 4.
Reattach the new diaper to a clean and happy
baby!
page 15
Crib + Changer Combo (5591)-Toddler Bed Conversion Assembly
* All of the parts and hardware you will need are
supplied with the crib at the time of purchase.
STEP 1.
STEP 2.
Unscrew the Allen head bolts and
remove the front panel assembly.
Move the spring frame to the lowest level.
STEP 3.
Attach the guardrail (L) to the front posts using
four Allen head bolts (H22) and lock washer
(H23). The guardrail (L) can be installed with
the high end facing either to the left or the
right.
Check to make sure that all of the bolts are
fastened securely.
DO NOT OVERTIGHTEN.
L.
H23 H22
H22 H23
L
H23
H22
H22
Gu
ard
H23
rai
l
L
The mattress intended for use on the bed shall be a full-size crib mattress having
minimum dimensions of 51-5/8 in. (1310mm) in length, 27-1/4 in. (690mm) in width
and 4 in. (100mm) in thickness, or a greater thickness not exceeding 6 in (152mm).
The intended user’s minimum age must be at
least 15 months old and maximum weight must not exceed 50 lbs (22.7 kg).
WARNING
:
Failure to follow these warnings and the assembly instructions could result in
serious injury or death from entrapment or strangulation.
DO NOT place bed near windows where cords from blinds or drapes may strangle a child. DO NOT place
items with a string, cord, or ribbon, around a child’s neck, such as hood strings or pacifier cords. DO NOT
suspend strings over a toddler bed for any reason. If guard rails are used as the mattress containment
means, guard rails provided must be used to avoid the formation of a gap between the mattress and the bed
that could cause an entrapment.
page 16
Crib + Changer Combo (5591) - Full Size Conversion Assembly
* For all 4 in 1 cribs, please contact a retailer to order your full size
adult wooden bed rails for your full size bed conversion.
3” Phillips Head Bolt X 8
Barrel Nut X 8
STEP 1.
Unscrew the Allen head bolts and remove
the left side panel (D).
H9
H25
H4
H1
H25
H3
H25
STEP 2.
Separate the dresser from the crib.
Replace the posts in the center panel with
front and back posts (G-3 & F-3) as illustrated.
H9
H2 H25
STEP 3.
H3
F-3
H25
Insert barrel nuts into bed rails. Use 3” Phillips
head bolts (A) to attach the rails. Tighten bolts
securely with a Phillips screwdriver.
Be sure to keep the extra bolts and barrel nuts
for future use.
DO NOT OVERTIGHTEN.
ils
a
dR
Be
ails
R
ed
B
G-3
page 17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement