Epson PhotoPC 800 User manual

Altair.book Page i Thursday, July 1, 1999 3:33 PM
User’s Guide
A
B
Altair.book Page ii Thursday, July 1, 1999 3:33 PM
IMPORTANT NOTICE
DISCLAIMER OF WARRANTY
Epson America makes no representations or warranties, either express or
implied, by or with respect to anything in this manual, and shall not be liable for
any implied warranties of merchantability and fitness for a particular purpose or
for any indirect, special, or consequential damages. Some states do not allow the
exclusion of incidental or consequential damages, so this exclusion may not
apply to you.
A NOTE CONCERNING RESPONSIBLE USE OF
COPYRIGHTED MATERIALS
Digital cameras and scanners, like photocopiers and conventional cameras, can
be misused by improper copying of copyrighted material. While some countries’
laws permit limited copying in certain circumstances, those circumstances may
not be as broad as some people assume. EPSON encourages each user to be
responsible and respectful of the copyright laws when using digital cameras and
scanners.
COPYRIGHT NOTICE
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written
permission of Epson America, Inc. No patent liability is assumed with respect to
the use of information contained herein. Nor is any liability assumed for
damages resulting from the use of the information contained herein. Further,
this publication and features described herein are subject to change without
notice.
TRADEMARKS
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON
CORPORATION.
PhotoPC is a registered trademark and EPSON FaxAdvice, EPSON Photo!3,
HyPict, PhotoEnhance, and Image Authentication System are trademarks of
Epson America, Inc.
EPSON SoundAdvice is a service mark of Epson America, Inc.
Image Expert and Camio are trademarks of Sierra Imaging, Inc. in the United
States and other countries and are used under license.
Lexar Media is a trademark of Lexar Media.
General notice: Other product names used herein are for identification purposes
only and may be trademarks of their respective owners. EPSON disclaims any
and all rights in those marks.
ii
Copyright © 1999 by Epson America, Inc.
Torrance, California, USA
CPD 8478
7/99
Altair.book Page iii Thursday, July 1, 1999 3:33 PM
Contents
Introduction
PhotoPC 800 Features
Optional Accessories
Minimum System Requirements
Windows Systems
Macintosh Systems
Where To Get Help
Software Support
Software Licensing
Registration
Safety Instructions
1
Intro-2
Intro-4
Intro-4
Intro-4
Intro-5
Intro-6
Intro-7
Intro-7
Intro-7
Intro-8
Getting Started
Unpacking Your PhotoPC 800
Identifying Camera Parts
Using Rechargeable NiMH Batteries
Charging Batteries
Installing Batteries
Battery Options
1-1
1-2
1-4
1-4
1-6
1-8
Attaching the Wrist Strap
Installing Your Memory Card
Setting the Date and Time
Formatting Your Memory Card
Removing Your Memory Card
Installing Your PhotoPC 800 Software
Installing for Windows 98, Windows 95,
or Windows NT 4.0
Installing on a Macintosh
2
1-9
1-10
1-11
1-12
1-13
1-14
1-14
1-16
Taking Pictures
Using the Camera Dial
Reading the Status Display Panel
Checking the Battery
Checking the Picture Counter
Taking Pictures With the Viewfinder
Taking Pictures With the LCD Screen
2-1
2-2
2-2
2-3
2-4
2-6
iii
A
B
Altair.book Page iv Thursday, July 1, 1999 3:33 PM
3
Using the Camera Buttons to Change
Settings
Setting Image Quality
Standard
Fine
Super Fine
HyPict
Using the Flash
Auto
Forced Flash
Flash Off
Slow Synchronized Flash
Taking Pictures With the Timer
Making Advanced Adjustments
Adjusting the Sensitivity Setting
Adjusting the White Balance Setting
Adjusting the Exposure Setting
4
Using the LCD Menus to Change Settings
Choosing the User Mode
Taking Color or Black and White Pictures
Taking Quick Shots
Taking Digital Zoom Pictures
Taking Close-Ups With Macro Mode
iv
3-1
3-2
3-2
3-2
3-2
3-3
3-3
3-3
3-3
3-3
3-4
3-5
3-5
3-6
3-7
4-2
4-4
4-4
4-5
4-7
Taking Digital Panoramic Pictures
Continuous Shooting
Continuous Shooting Using the Timer
Interval Shooting
Adding Voice Recordings to Pictures
Using Programmed Subject Settings
Adjusting the Sensitivity Setting
Adjusting the White Balance Setting
Photographing With Fixed White Balance
Photographing With User Defined White
Balance
Adjusting Exposure
Making Predefined Exposure Adjustments
Making Advanced Exposure Adjustments
Adjusting the Focus
Changing the Metering Method
Setting Camera Options
Setting the Automatic Power Off Feature
Setting the LCD Brightness
Setting the Alert Beep
Setting the Time and Date
Setting the Language
4-8
4-10
4-11
4-12
4-13
4-15
4-17
4-18
4-19
4-21
4-22
4-23
4-24
4-24
4-25
4-26
4-26
4-28
4-28
4-29
4-30
Altair.book Page v Thursday, July 1, 1999 3:33 PM
5
Playing Back Photos
Playing Back Pictures One by One
Playing Back Multiple Pictures
Deleting Pictures
Deleting the Currently Displayed Picture
Deleting All Pictures
Deleting Selected Pictures
Locking Pictures
Unlocking Pictures
Adding Audio Recordings
Deleting Audio Recordings
Magnifying a Picture
Viewing Picture Information
Playing Your Pictures as a Slide Show
Excluding Pictures From a Slide Show
Rotating Pictures in a Slide Show
Playing Back Pictures on TV
5-2
5-3
5-4
5-4
5-5
5-5
5-6
5-8
5-8
5-10
5-11
5-12
5-13
5-14
5-15
5-17
Getting Images Into TWAIN-Compliant
Applications
Getting Images That You Can Import
What To Do If the Camera Is Not
Responding
7
Getting Photos Into Your Computer
Connecting the Camera
Connecting to a Windows PC
Connecting to a Macintosh
Transferring Photos and Sound Files
What To Do if You See an Error Message
6-1
6-2
6-4
6-5
6-9
6-14
Getting Your Photos Into Documents
Importing Images Into Documents
Getting Images With Copy and Paste
Using Drag and Drop From an Album
(Windows Only)
Getting Images With the Camio Viewer
(Windows)
Dragging and Dropping a Picture Into
a Document
Transferring Images Before Placing Them
8
6
6-10
6-12
7-2
7-3
7-4
7-6
7-7
7-8
Working With Photos and Albums
Using Image Expert Albums
Organizing Pictures in Albums
Renaming a Picture
Viewing Picture Information
8-2
8-2
8-3
8-3
A
B
v
Altair.book Page vi Thursday, July 1, 1999 3:33 PM
Printing an Image or Album
Choosing the Layout Style
Adding Text
Choosing Album Images
Adjusting the Printed Area
Adding Sound to an Image
Playing Back Sounds
Editing Sounds
Deleting Sounds
Displaying Albums as Slide Shows
Using an Album as a Screen Saver
Setting an Image as Wallpaper
Copying to Diskette or Zip Disk
Viewing the Pictures on Diskette or
Zip Disk
Sending Pictures and Sound by E-mail
9
8-14
8-14
Editing Images
Viewing and Selecting Images
Applying Quick Fix
Correcting an Image
Cropping an Image
Resizing an Image
Rotating an Image
Flipping an Image
vi
8-4
8-5
8-6
8-7
8-7
8-8
8-9
8-10
8-10
8-11
8-12
8-12
8-13
9-2
9-3
9-3
9-5
9-5
9-6
9-7
Applying Special Effects
Changing the Number of Colors
9-8
9-9
10 Operating the Camera From Your Computer
Taking Pictures From Your Computer With
Image Expert
Using the Self Timer
Taking Pictures With EPSON Photo!3
Adjusting Camera Settings From Your Computer
Changing Settings With Image Expert
Changing Settings With EPSON Photo!3
10-1
10-3
10-4
10-5
10-5
10-7
11 Using Your Camera for Presentations
Uploading Images to the Camera
11-1
Uploading Images From Your Windows PC 11-2
Uploading Images From Your Macintosh
11-5
Converting Presentations
11-7
Capturing Windows Screens
11-8
Capturing Macintosh Screens
11-9
Projecting Your Presentation
11-11
12 Printing Directly From the Camera
Connecting the Camera to the Printer
Starting Direct Print
12-2
12-3
Altair.book Page vii Thursday, July 1, 1999 3:33 PM
Printing
Printing Single and Multiple Images
Producing Your Printout
Printing a Card
Printing Album Images
Printing Stickers
Printing an Index of Your Images
Removing the Direct Print Program
Reinstalling the Direct Print Program
Reading Error and Status Messages
12-4
12-4
12-8
12-10
12-11
12-13
12-15
12-16
12-17
12-17
13 Maintenance and Troubleshooting
Caring for the Camera and Battery Charger
Cleaning the Camera and Battery Charger
Storing the Camera
Solving Camera Problems
Solving Picture Problems
13-1
13-1
13-2
13-2
13-8
Camera
Physical Dimensions
Power
Technical
Environmental
Safety
Photographic
Memory Card Picture Capacity
NiMH Battery Charger
Physical Dimensions
Technical
Optional AC Adapter
Physical Dimensions
Technical
CompactFlash Card
Physical Dimensions
B-1
B-1
B-1
B-2
B-3
B-3
B-3
B-4
B-5
B-5
B-5
B-5
B-5
B-5
B-5
B-5
Index
A Optional Accessories
Using the Universal AC Adapter
Using an Optional Tripod
Using a PCMCIA Adapter
Installing the PCMCIA Adapter
Transferring Photos With the Adapter
About the IOMEGA Clik! Drive
B Specifications
A-2
A-4
A-4
A-4
A-5
A-6
A
B
vii
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
Introduction
Y
our new EPSON PhotoPC 800 is a high resolution,
two megapixel, USB and serial digital camera small
enough to fit in your pocket, purse, or briefcase. It includes
three different user modes with three levels of control: fully
automatic point-and-shoot for the beginner photographer,
and increasing levels of control for intermediate and expert
photographers.
The PhotoPC 800 comes with a built-in microphone that
lets you add voice messages to your photos, and an LCD
screen so you can view your pictures before and after you
capture them. You can display your images on a TV or
multimedia projector, or transfer them to your computer.
You can even upload pictures, text, and graphics into your
camera, and play them back for presentations.
Introduction 1
A
B
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
The PhotoPC 800 captures images at 1600 × 1200 pixel
◗
24-bit color or grayscale image capture
resolution in 24-bit color, using a 2.14 megapixel CCD
sensor. With EPSON’s HyPict™ image enhancement
◗
High-speed image processing (one second per image in
technology, the images can be interpolated to 1984 × 1488
pixels right inside the camera.
◗
Your PhotoPC 800 comes complete with cables, batteries,
battery charger, soft camera case, handstrap, and 8MB
CompactFlash™ memory card. It also comes with a
CD-ROM with software and utilities for downloading,
editing, organizing, and printing your pictures.
quick shot mode)
approximately 24 fine-resolution or 120 standardresolution images
◗
Built-in microphone that lets you record a voice message
of up to 10 seconds for each picture
◗
1.8-inch, active matrix TFT color LCD screen that
supports instant preview, playback, delete, and power
save mode
PhotoPC 800 Features
PhotoPC 800 is a complete system for capturing digital
images, and includes the following features:
◗
2.14 million pixel CCD sensor
◗
Resolutions of 1600 × 1200 pixels, and up to
1984 × 1488 pixels (interpolated) using EPSON’s
HyPict image enhancement technology
2 Introduction
8MB EPSON CompactFlash card that holds
◗
Capability to print directly to several EPSON ink jet
printers—without using a computer
◗
Video output for playing your pictures back on a TV,
VCR, or projector
◗
Macro, 2× digital zoom, panorama, quick shot mode, and
interval and continuous shooting
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
◗
Adjustments for white balance, exposure, sensitivity,
◗
aperture, shutter, and focus
◗
presentation slides into image files and uploading them
to your camera
Built-in flash with a slow synchronized mode for night
photography
◗
Four rechargeable NiMH AA batteries and a fast charger
◗
Automatic shut-off to save batteries
◗
Automatic date and time recording for each picture
◗
Serial and USB cables for transferring photos to your
Windows or Macintosh computer
◗
Fully USB-compatible
EPSON Photo File Uploader for converting
◗
EPSON Photo Program Uploader for installing the
Direct Print program on your camera (Direct Print lets
you print directly from the camera to a number of
EPSON ink jet printers)
Your camera comes with the PhotoPC 800 software suite,
which includes the following applications for both PC and
Macintosh users:
◗
Sierra Imaging Image Expert™ software for transferring,
organizing, editing, and printing your pictures
◗
The EPSON Photo!3™ application and TWAIN driver
for transferring your pictures
A
B
Introduction 3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Optional Accessories
Minimum System Requirements
EPSON offers these accessories for the PhotoPC 800:
To transfer images to your computer and edit them, make
◗
sure your system meets these minimum requirements:
Universal AC adapter (B867062) for use with any
standard (100 to 240 V) electrical outlet
◗
◗
◗
Additional or replacement NiMH rechargeable batteries
(B818061)
Windows Systems
◗
IBM-compatible PC with 486 or higher processor
◗
Microsoft Windows 98, Windows 95, or
Windows NT 4.0 (Service Pack 3 or later
Additional or replacement universal NiMH Power Pak,
which includes batteries and charger (B818172)
EPSON Image Authentication System ™ (IAS) software
(PPC8–IAS)
recommended)
◗
or higher), or USB support for Windows 98 computer
with built-in USB port.
You can also obtain additional CompactFlash memory cards
and PCMCIA adapters from leading suppliers, such as Lexar
Media™ and SanDisk.
4 Introduction
Serial port with standard RS-232C interface (19200 bps
◗
At least 32MB RAM
◗
Double-speed CD-ROM drive
◗
At least 40MB free hard disk space
◗
VGA or SVGA monitor with at least 256-color display
◗
Mouse or other pointing device
◗
16-bit sound card and speakers (for voice annotation
feature only)
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Macintosh Systems
◗
One of the following systems:
If your iMac is running OS 8.1, you must download and install the
Macintosh PowerPC with System Software Version
iMac Update 1.0 from Apple at http://swupdates.info.apple.com
7.5 or later
before you install the PhotoPC 800 software. Contact Apple
™
Computer if you have problems installing this update or if you
®
Power Macintosh G3 with System Software Version
8.51 or later
™
iMac computer with System Software Version 8.1 with
iMac Update 1.0
◗
At least 32MB RAM
◗
At least 30MB free hard disk space
◗
CD-ROM drive
◗
VGA monitor with minimum resolution of 640 × 480
◗
Macintosh modem/printer serial port (19200 bps, or
◗
NOTE
have any questions. If your iMac is running OS 8.5, you do not
need to download and install the iMac Update 1.0. Your operating
system already includes full support for the PhotoPC 800
software. (To find out which operating system your iMac is
running, select About This Computer in the Apple menu.)
higher) or built-in USB port on an iMac or new
Power Mac G3
A
16-bit sound card and speakers (for voice annotation
feature only)
B
Introduction 5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
Where To Get Help
EPSON provides technical assistance through electronic
support services and automated telephone services
24 hours a day.
The following tables list the contact information:
Electronic support services
Service
Access
World Wide Web
From the Internet, you can reach EPSON’s Home
Page at http://www.epson.com.
EPSON Internet FTP Site
If you have Internet FTP capability, use your Web
browser (or other software for FTP downloading)
to log onto ftp.epson.com with the user name
anonymous and your e-mail address as the
password.
EPSON Forum on
CompuServe®
Members of CompuServe can type GO EPSON at
the menu prompt to reach the Epson America
Forum. For a free introductory CompuServe
membership, call (800) 848-8199 and ask for
representative #529.
Automated telephone services
Service
EPSON SoundAdvice
6 Introduction
Access
SM
For pre-recorded answers to commonly asked
questions about EPSON products 24 hours a day,
seven days a week, call (800) 922-8911.
Automated telephone services
Service
EPSON FaxAdvice
Access
™
EPSON Referral Service
Access EPSON’s technical information library by
calling (800) 922-8911. You must provide a return
fax number to use this service.
For the location of your nearest Authorized
EPSON Reseller call (800) 922-8911.
To speak to a technical support representative, dial
(310) 974-1983 (U.S.), or (905) 709-3839 (Canada),
6 AM to 6 PM, Pacific Time, Monday through Friday.
Toll or long distance charges may apply.
Before you call, please have the following information ready:
◗
Product name
◗
Product serial number
◗
Computer configuration
◗
Description of the problem
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
You can purchase manuals and accessories from EPSON
Software Licensing
Accessories at (800) 873-7766 (U.S. sales only). In Canada,
please call (800) 873-7766 for dealer referral. Or visit our
You can install EPSON Photo!3, the EPSON Photo File
website at www.epsonsupplies.com (U.S. sales only).
Uploader, and the EPSON Photo!3 Program Uploader on
multiple computer systems. If you want to install Image
Software Support
Expert on multiple computer systems, please contact Sierra
Imaging at (800) 501-8902 regarding the licensing fee.
If you are having problems with a software application
included with the camera, you can call one of the following
numbers for technical support:
Registration
◗
PhotoPC 800 digital camera and mail it back to us. This
enables you to receive special information on accessories,
(800) 501-8902 for Sierra Imaging Image Expert
software questions. Available weekdays 9 AM to 5 PM,
Pacific Time. Or e-mail [email protected].
Worldwide support number is (831) 461-4710.
◗
Please take a minute to fill out the registration card for the
new products, and software upgrades. You’ll get immediate
attention if you have a problem with your PhotoPC 800.
(310) 974-1983 for the EPSON Photo!3 application
and TWAIN driver, the EPSON Photo File Uploader,
the EPSON Photo!3 Program Uploader, and the Direct
Print software.
A
B
Introduction 7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
Safety Instructions
◗
odor, or smoke, unplug it immediately.
Read all of these instructions before using your camera and
battery charger. Also follow all warnings and instructions
◗
◗
To reduce the risk of electric shock, do not remove the
camera’s cover or open any of the compartments except
as instructed in this User’s Guide.
To prevent fire or electric shock, do not insert objects
◗
◗
Do not use the charger near water. Never insert or
remove the charger’s power plug with wet hands.
◗
Keep the charger away from heat sources. Do not use
outside the temperature range of 32 to 95 °F
(0 to 35 °C).
through any openings in the camera or battery charger.
Do not expose the camera or battery charger to rain or
◗
To avoid damage to the optics of the camera, do not
expose the lens to direct sunlight for extended periods of
time.
marked on the camera, battery charger, and batteries.
◗
If the battery charger shows unusual signs such as noise,
moisture.
◗
Do not use the charger within reach of children.
To prevent fire or explosion, do not use the camera or
◗
Do not insert batteries backwards.
battery charger where inflammable or volatile gas is
stored.
◗
Use only the types of power sources listed on the charger
label and in this User’s Guide. Always supply power to
the charger directly from a standard domestic electrical
If the camera shows unusual signs such as noise, odor, or
smoke, turn it off immediately. Remove the batteries
and/or disconnect the AC adapter, and unplug the AC
adapter from the electrical outlet.
8 Introduction
outlet.
◗
Do not charge the batteries using an electrical outlet on
an airplane.
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
◗
Do not use the camera outdoors during adverse weather
◗
conditions.
◗
◗
Do not store the camera near sources of bright light,
adapter and refer servicing to qualified service personnel
under the following conditions: if the power cord or
direct sunlight, high humidity, heat, excessive dirt or
dust, or where it will be exposed to strong vibrations or
plug is damaged; if liquid has entered the camera; if the
camera has been dropped or its exterior has been
magnetic fields.
damaged; if the camera or its optional accessories do not
To prevent possible eye injury, do not take flash pictures
operate normally or exhibit a distinct change in
performance.
of faces at close range.
◗
Avoid sudden temperature changes, which can cause
moisture to condense on the camera. Keep the camera in
a case or bag if you need to move it from a cold
◗
changes before using them.
Do not use a frayed or damaged power cord with the
AC adapter.
Adjust only those controls that are covered by the
operating instructions.
◗
Do not attempt to service the camera or battery charger
yourself. Refer all servicing to qualified service
personnel.
environment to a warm one. Allow time for the camera
and its optional accessories to adjust to temperature
◗
Remove batteries and/or unplug the camera and the AC
◗
If the liquid crystal solution contained in the display
panel or in the LCD screen leaks out and gets on your
hands, wash them thoroughly with soap and water. If it
gets in your eyes, flush them immediately with water.
A
B
Introduction 9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
10 Introduction
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
1
.
14
1
Getting Started
Unpacking Your PhotoPC 800
B
efore you can start using your PhotoPC 800, you
Make sure you have all the parts shown below.
need to charge the batteries. You should also be familiar
with all the camera components.
camera bag
battery charger
This chapter describes the following:
camera
◗
Unpacking your PhotoPC 800
◗
Identifying camera parts
◗
Using rechargeable NiMH batteries
◗
Attaching the wrist strap
◗
Using the CompactFlash memory card
◗
Setting the date and time
◗
Installing your PhotoPC 800 software
wrist strap
software
CompactFlash
card (8MB)
video cable
PC serial cable
AC power cord
rechargeable
batteries
Mac/Direct Print
serial cable
USB cable
Getting Started 1-1
A
B
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Identifying Camera Parts
camera dial
shutter button
tripod
socket
flash
memory
card cover
battery
cover
battery
cover lock
timer light
viewfinder
video out
connector
memory
card cover
lock
lens cover switch
lens
front view
1-2 Getting Started
AC adapter
connector
interface
connector
bottom view
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
1
camera status light
status display panel
viewfinder
and photo
capture light
image quality button
shutter button
camera dial
hand strap
holder
flash button
self timer button
top button
(unlabeled)
microphone
+ button
LCD
screen
MENU
button
dial lock
top view
− button
ISO
W.B.
button
button
bottom
button
(unlabeled)
A
back view
B
Getting Started 1-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Using Rechargeable NiMH Batteries
WARNING
Your PhotoPC 800 comes with a charger and four
Shock hazard. Make sure you use the charger only with EPSON
rechargeable NiMH batteries that can be recharged hundreds
rechargeable NiMH batteries (model EU-24). To avoid the danger
of times. While you use two batteries in your camera, you
can keep a replacement set of batteries charged and ready to
of leakage or explosion, do not place any other batteries in the
take along.
NOTE
New batteries need to be fully charged three times before you
use them. This process takes approximately five or six hours—
but you only need to do it once. When you need to recharge your
batteries in the future, it takes approximately two and a half hours
for a full charge.
Charging Batteries
It’s important to fully charge your batteries, so they will last
as long as possible before they need recharging.
1-4 Getting Started
charger. Read all safety and handling instructions in the
Introduction of this guide before using the charger.
Follow these steps to charge your batteries for the first time:
1
Insert two or four batteries, positioning the + and – ends
as shown.
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
2
Connect the battery charger to the battery charger power
4
cord, as shown below.
Now charge your batteries again by unplugging the
1
battery power cord and then plugging it in again.
5
Charge the batteries a third time. After the charger light
goes off, unplug the charger. To avoid overcharging,
don’t leave the charger plugged in for long periods of
time after the light goes off.
6
Wait one hour until the batteries cool before removing
them from the charger.
7
Before storing the charger, disconnect the power cord
charger light
3
Plug the charger into an electrical outlet. The charger
and remove the batteries.
light turns red, indicating that the charger is working.
When the batteries are charged, after about two and a
half hours, the light goes off.
(For subsequent charges of your NiMH rechargeable
NOTE
Be sure to charge the batteries completely to make them last
The charger light flashes to indicate changes in battery
temperature and voltage. If the light continues to flash for
more than half an hour, the batteries may be damaged or
batteries, follow steps 1 through 3, then unplug the charger
and follow steps 6 and 7 above.)
as long as possible. They can be recharged hundreds of times,
so do not dispose of them until they are worn out.
A
B
worn out, and should be replaced. Unplug the charger if the
batteries are not fully charged after four hours.
Getting Started 1-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
NOTE
To keep the charger terminals clean, unplug the charger and wipe
the terminals with a dry cloth. Make sure you charge the batteries
before you use them. If you find that your batteries run out faster
after you recharge them a few times, make sure you discharge
them completely before recharging. If this doesn’t help, replace
the batteries.
Installing Batteries
Before you install the batteries, make sure the camera is
turned off.
1
Turn the camera upside down.
2
Hold the battery cover lock down and slide the cover
out to open it.
1-6 Getting Started
battery cover lock
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
3
Insert two batteries into the compartment, positioning
4
Lower the battery cover and slide it in, as shown below.
1
the + and − ends as shown below.
When the battery power is almost out, a low battery icon
appears on the camera’s display panel. Be sure to
replace both batteries at the same time.
A
B
Getting Started 1-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
Battery Options
◗
Do not use manganese batteries.
If you forget to charge your rechargeable NiMH batteries or
◗
Do not mix different types of batteries; this can cause
if they need to be replaced, the PhotoPC 800 camera can also
accept the following:
◗
Rechargeable AA NiCad batteries
◗
Single-use AA lithium batteries (longer life, Energizer
fire or explosion.
◗
and new batteries.
◗
To avoid the danger of fire or explosion, do not mix different
◗
◗
battery’s circuits. Read all safety and handling instructions before
◗
Do not drop, puncture, disassemble, or mutilate
batteries. Do not get them wet or expose them to fire.
◗
charge the batteries that came with your camera.
When the camera is not used for long periods of time,
remove the batteries and store them at a low temperature
Use the batteries that came with your camera only in
in a dry location. Store away from the reach of children.
Note the following when handling batteries:
◗
If the batteries are charged in a hot environment, or if
they are charged repeatedly without being discharged,
they will wear out more quickly.
using batteries.
◗
Batteries discharge at least 2% per day, whether they are
used or not.
types of batteries. Do not allow the battery contacts to touch
metal objects such as coins or keys, which could short out the
Batteries that have not been used for a long time do not
charge well. However, with regular use, the batteries will
return to normal.
recommended)
WARNING
Replace both batteries at the same time. Do not mix old
Use only the EPSON battery charger (Model EU-38) to
EPSON digital cameras.
1-8 Getting Started
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
◗
◗
To avoid fire or electric shock, do not use batteries that
Attaching the Wrist Strap
are leaking or damaged in any way.
To attach the wrist strap, follow these steps:
If battery acid gets in your eyes or on your skin,
immediately rinse the area with water and seek medical
treatment. If a battery is swallowed, seek medical
1
Dispose of used batteries according to the
manufacturer’s instructions and in compliance with all
applicable laws. Contact your local government agency
Push the loop on the end of the strap through the small
opening in the holder on the side of the camera. (You
may need to use a small pointed object, such as the tip of
an untwisted paper clip, to push it through.)
treatment immediately.
◗
1
2
Pull the strap through the loop and tighten, as shown
below.
for information about battery recycling and disposal.
◗
Battery life varies depending on the battery type, the
manufacturer, and other factors.
A
B
Getting Started 1-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
Installing Your Memory Card
Your camera comes with an 8MB CompactFlash memory
card that you need to install before you take any photos.
Since there is no internal camera memory for storage, this
card will store your photographs until you transfer them to
your computer.
You can purchase additional memory cards (4MB to 96MB)
from leading suppliers like Lexar Media and SanDisk. See
page A-2 for more information.
1
Make sure the camera dial is turned to Off and the lens
cover is closed. (To change the dial setting, press the
white dial lock in and turn the dial.)
dial lock
1-10 Getting Started
2
Turn the camera upside down and open the memory
card cover by sliding the memory card cover lock in the
direction of the arrow, as shown below.
memory card
cover lock
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
3
1
Insert the card all the way into the memory card slot.
Setting the Date and Time
Make sure the front of the card is facing the front of the
camera, and the arrow on the card’s label is pointing
Before you use the camera, you need to set its clock. Then
down.
each picture you take. You may need to set the clock again if
you don’t use it for extended periods of time.
the camera will automatically record the date and time for
NOTE
You can also set the camera’s clock through your computer. See
page 6-1 for instructions on connecting the camera to your
computer, and page 10-5 for instructions on setting the date and
time.
camera dial
front of camera
camera dial lock
4
Close the memory card cover.
top button
Next, you need to set the camera’s date and time in
+ button
preparation for formatting the memory card.
− button
MENU button
A
bottom button
B
W.B. button
Getting Started 1-11
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
Follow these steps to set the date and time:
1
.
You see the clock setting screen with the month
highlighted in red.
When you’re finished, press the MENU button (under
BACK). You see the SETUP menu.
Push the camera dial lock in and turn the camera dial
to
2
5
6
Turn the camera dial Off.
Now you’re ready to format the memory card.
Formatting Your Memory Card
You should format your card before you use it. Follow these
steps:
1
Turn the camera dial to
. Then press the W.B. button
(below Memory SETUP). The Memory Card Format
menu appears if a memory card is installed in the
camera.
3
Press the + or − button (next to the up and down
arrows) to increase or decrease the number, until the
month is correct.
4
Press the W.B. button (below the right arrow) to move
through the day and year, and make adjustments as
described in the previous step.
1-12 Getting Started
Altair.book Page 13 Thursday, July 1, 1999 3:33 PM
2
Press the top button (next to MEMORY CARD
FORMAT) to format the card. You see a message
2
Press the eject button next to the memory card and
1
remove the card by hand. Then close the cover.
warning you that all data on the card will be deleted if
you format it.
3
eject button
Press the button next to Yes to format the card, or the
button next to No to cancel.
Removing Your Memory Card
Turn your camera dial to Off before you remove the card.
CAUTION
Never remove the card while the camera is on. Data in the card
may be lost or damaged.
1
Open the memory card cover.
A
B
Getting Started 1-13
Altair.book Page 14 Thursday, July 1, 1999 3:33 PM
Installing Your PhotoPC 800
Software
Installing for Windows 98, Windows 95, or
Windows NT 4.0
PhotoPC 800 comes with everything you need to transfer
Follow these steps:
your pictures from the camera to your computer, organize,
enhance, and share your images, and insert them into
1
documents. You can also upload pictures and presentations
Insert the CD-ROM in your drive. The Setup program
starts automatically.
If it doesn’t start automatically, double-click My
Computer. Then double-click your CD-ROM icon.
to your camera. The PhotoPC 800 CD-ROM has these
applications for your Windows or Macintosh computer:
◗
Sierra Imaging Image Expert
2
On the first screen, select the language you want to use.
◗
EPSON Photo!3 TWAIN and standalone application,
and EPSON Photo!3 Program Uploader
3
When you see the following screen, click the Install
◗
EPSON Photo File Uploader
Follow the steps in the appropriate section below to install
the software on your computer.
1-14 Getting Started
Image Expert button.
Altair.book Page 15 Thursday, July 1, 1999 3:33 PM
4
Follow the instructions on the screen to install Image
Expert. When installation is complete, you return to the
Setup screen.
5
Click the button labeled Install EPSON Photo!3 and
Program Uploader and follow the instructions on the
screen.
6
When you return to the Setup screen, click the Install
EPSON Photo File Uploader button. Follow the
1
NOTE
You may need your Windows 98 system disk to perform this
installation.
Follow these steps to install the driver for your camera:
1
Insert your PhotoPC 800 CD-ROM in your CD-ROM
drive, if necessary.
2
At the first screen, click Next.
3
Select Search for the best driver for your device,
instructions on the screen.
7
When installation is complete, click Exit.
Your camera software is now installed.
then click Next.
4
Select Specify a location and browse to your
CD-ROM drive.
5
Select the Win98E folder if you’re installing the English
driver (or the Win98S folder to install the Spanish
Installing Your Windows 98 USB Driver
If you’re installing on a Windows 98 system with a USB
port, complete the steps above to install your software. The
first time you connect the camera to your computer with
your USB cable, you’ll see the Add New Hardware Wizard.
driver, or the Win98F folder to install the French
driver). Click OK.
Click Cancel. (See page 6-2 if you need help connecting the
A
B
camera.)
Getting Started 1-15
Altair.book Page 16 Thursday, July 1, 1999 3:33 PM
6
On the following screen, click Next. The wizard locates
6
EPSON Photo!3 Ver. 1 folder.
your camera’s driver.
7
Click Next on the installation screen to install the
driver. When installation is complete, click Finish.
7
Follow these steps:
1
Insert the CD-ROM in your drive.
2
If necessary, double-click the CD-ROM icon to open it.
3
Open the folder for the language you want to use.
Double-click the Photo!3 Installer – Part 1 icon.
Click Continue and follow the instructions on the
screen. When installation is complete, click Restart to
Your camera software is now installed.
Installing on a Macintosh
Open the folder for your language, then open the
restart your computer.
8
Open the folder for your language. Then copy the
EPSON Photo File Uploader folder to the EPSON
Photo!3 Ver. 1 folder on your hard drive.
NOTE
To create the preferences for the EPSON Photo File
4
Uploader, start, then close the EPSON Photo!3 program
on your hard drive. You need these preferences to run Photo
Double-click the Install Image Expert icon. Click
File Uploader.
Continue and follow the instructions on the screen.
5
When you’re done installing Image Expert, click
Restart to restart your computer.
1-16 Getting Started
Your camera software is now installed.
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
2
T
2
Taking Pictures
aking pictures with the PhotoPC 800 is similar to
Using the Camera Dial
using a traditional “point and shoot” auto focus
camera. This chapter gives you all the basic information you
The camera dial has an
need to start taking pictures, including the following:
settings: three for taking
◗
Using the camera dial
pictures, and three for
performing other functions,
◗
Reading the status display panel
◗
Taking pictures with the viewfinder
such as setting up your
photos or playing them
◗
Taking pictures with the LCD screen
back on the LCD screen.
Off position and six other
dial lock
When Off is selected, press the white dial lock in to turn the
dial. (You don’t need to press the dial lock in when another
setting is selected.)
A
B
Taking Pictures 2-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Camera dial settings include the following:
Reading the Status Display Panel
Use this setting for continuous and interval
When your camera dial is turned to
,
, or
, the status
shooting. See pages 4-10 through 4-13 for details.
display panel shows the camera’s current settings and how
many additional pictures you can take.
Use this setting to take photos with the LCD screen.
See Chapter 4 for information about how to change
.
image quality
settings in the View menus.
Use this setting to take photos with the optical
viewfinder. See page 2-4 for details.
Use this setting to play back, delete, and add voice
recording to your photos. See Chapter 5 for details.
Use this setting to print directly from your camera to
an EPSON ink jet printer. See Chapter 12.
sensitivity
white
balance
flash
low
battery
icon
timer
monochrome
indicator
exposure
pictures
remaining
Use this setting to set up or view information about
your camera on the Setup screen. See Chapter 4 for
information.
Checking the Battery
When your battery power is almost out, the low
battery icon appears on the display panel. The icon
flashes when your battery power is completely out.
2-2 Taking Pictures
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
You need to recharge or replace the batteries or use the
Before you can take any more pictures, you need to delete
optional universal AC adapter when you see the low battery
icon. Although you may be able to use the camera with low
some of the images on the memory card. (See page 5-4 for
instructions.)
batteries, it needs full battery power to operate reliably.
If you want to save your photos before you delete them,
Several factors can affect battery life, including the
connect the camera to your computer and transfer the
surrounding temperature and the type of batteries you use.
Low temperatures—especially below 50 °F (10 °C)—drain
pictures as described in Chapter 6.
batteries faster. See page 1-4 for battery use instructions.
Instead of the number of pictures remaining, you may see
one of the following in the lower right corner of the status
Checking the Picture Counter
display panel:
The large number in the lower right of the status display
In quick shot mode, the number of photos
taken is displayed in brackets.
panel shows how many additional pictures you can take.
This number is affected by the image quality setting. Also,
if you have any voice recordings stored on your memory
card, the number on the display panel may be greater than
the actual number of remaining pictures.
When the memory card is full, the number on the display
panel reads 0, the status light on the back of the camera
2
In Program or Manual mode, the exposure
value appears on the left and the shutter
speed appears on the right when you hold the
shutter button down halfway. See page 4-2
for more information about user modes.
A
B
flashes red, and you can no longer use the shutter button.
Taking Pictures 2-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
When you turn the camera’s dial to
, SEt
is displayed. No other information appears
in the status display panel.
When you make a voice recording, rEc
Taking Pictures With the Viewfinder
You can capture an image as you would with any
point-and-shoot auto-focus camera: look through the optical
viewfinder and press the two-step shutter.
appears in this space.
viewfinder
camera dial
When you take photos using the interval
shooting feature, Int appears in the display
panel.
photo capture light
camera status light
NOTE
One advantage of the optical viewfinder is that it uses less
battery power than taking pictures with the LCD screen.
However, you can’t use the optical viewfinder when you make
voice recordings or use the panorama or digital zoom features.
2-4 Taking Pictures
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Follow these steps:
1
viewfinder
camera status light
shutter button
2
Make sure you are at least 20 inches (50 cm) away from
your subject. (If you want to get closer, use macro mode
as described on page 4-7.)
2
Slide the lens cover switch to open the lens cover. Then
turn the camera dial to
photo capture
status light
and wait until the status light
turns green.
3
Look straight through the viewfinder and center your
subject within the cross-hairs.
NOTE
4
The frame in the viewfinder indicates the area captured
Use the camera’s controls to make any changes you want
to image quality, the flash, or other basic settings. (See
Chapter 3 for information about changing settings when
taking pictures with the viewfinder.)
when taking pictures at close range.
5
Hold the shutter button halfway down to lock the auto
focus.
A
B
Taking Pictures 2-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
6
While holding down the shutter button, you can
After you take a picture, the photo capture status light
reframe your picture and move your subject off-center if
you want. The photo capture status light stops flashing
flashes. This indicates that the image was captured and the
camera is processing it. When the light stops flashing, the
when the lens locks in focus.
image is saved.
Press the shutter button the rest of the way down to take
the picture.
CAUTION
If you set the camera down while the light is still flashing, make
sure you handle it carefully. The camera may lose your image if
you set it down too hard.
7
Hold the camera still until it beeps, then release the
shutter button.
NOTE
You may notice a brief delay between the time you press the
shutter button and when the camera beeps. To avoid blurring
your images, make sure you hold the camera still until it beeps.
Saved images remain on the memory card even when you
turn the camera off or remove the memory card or the
batteries.
Taking Pictures With the LCD Screen
The LCD screen lets you see a live preview of what the
camera’s lens sees at any moment. Although you can use this
setting anytime, you always choose it when you want to use
the panorama or digital zoom features, or when you want to
make voice recordings to go with your photos.
2-6 Taking Pictures
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
NOTE
Before you begin to take pictures, you can use the LCD menus to
turn recording on and make many other adjustments to your
camera. See Chapter 4 for details.
The following screen illustrates what you see if your
camera is set to Full Auto user mode, the default user
mode. The settings may look different if you’re using
2
Program or Manual user mode. See Chapter 4 for details
about user mode.
Follow these steps:
1
Make sure you are at least 20 inches (50 cm) away from
your subject. (If you want to get closer, use macro mode
image
quality
digital zoom
as described on page 4-7.)
2
Slide the lens cover switch to open the lens cover. Then
to see the View menu. Wait
turn the camera dial to
until the camera status light turns green.
Normal
Macro
Panorama
You see a preview of your picture on the LCD screen,
with the image quality setting in the upper left corner of
the screen and the digital zoom setting in the upper
A
right.
B
Taking Pictures 2-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
The camera status light stops flashing and you see a
NOTE
after a designated period of inactivity. (The default is 10
green circle
on the screen when the lens locks in
focus. While you hold the shutter button down, you can
seconds. See page 4-26 for instructions on setting the
reframe your picture if you want.
If you’re using batteries, the camera shuts off automatically
power off interval.) If the image on your LCD screen
disappears, press the shutter button to “wake” the camera.
3
camera status light
Using the preview image to guide you, make any final
changes to the settings on the View menu. See
Chapter 4 for details.
microphone
NOTE
You can also use the camera’s buttons to change the image
quality, flash, or timer. See Chapter 3.
4
Center your subject on the screen, then press the shutter
button halfway down to lock the auto focus.
2-8 Taking Pictures
press to
delete
5
Press the shutter button the rest of the way down to take
the picture.
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
6
Hold the camera still until it beeps. Then release the
When the camera status light stops flashing, you’re ready
shutter button. (You may notice a brief delay between
the time you press the shutter button and when the
to take another picture. Or, if you’ve turned recording
on, you see a countdown of the recording time on the
camera beeps. To avoid blurring your images, make sure
you hold the camera still until it beeps.)
screen. During this time, you can record a message into
the built-in microphone on the back of the camera. (See
2
page 4-13 for more information on recording a
After a few seconds, you see a confirmation screen.
message.)
NOTE
◗
The LCD screen uses up battery power quickly. If it’s idle for
more than the designated power off interval, the camera
turns off automatically. To turn it back on, press the shutter
button, or turn the camera dial to Off and then back to
.
See page 4-26 for instructions on changing the power off
interval.
◗
Even if you don’t speak into the microphone, your camera
NOTE
records ambient noise when recording is turned on, and your
You can press the button next to Delete if you don’t want
images take up more space on the memory card. To fit more
the picture. You can also delete pictures in playback mode.
images on your memory card, make sure you turn recording
(See Chapter 5 for details.)
off when you no longer want to use it.
A
B
Taking Pictures 2-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
2-10 Taking Pictures
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
3
Y
Using the Camera Buttons to Change
Settings
ou use the camera’s buttons to set the flash, enable
the timer, and set image quality. You can also make
quick adjustments to other basic settings, which gives you
greater control of your images when you’re taking pictures
3
Setting Image Quality
The PhotoPC 800 has four image quality (resolution)
settings. Press the image quality button on top of the camera
to cycle from one setting to the other.
with the viewfinder. This chapter explains the following:
◗
Setting image quality
◗
Using the flash
◗
Taking pictures with the timer
◗
Adjusting the sensitivity setting
◗
Adjusting the white balance setting
◗
Adjusting the exposure setting
NOTE
The camera dial must be turned to
,
, or
.
image quality
button
A
B
Using the Camera Buttons to Change Settings 3-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
The image quality icons appear on the status display panel as
described below.
Standard
Produces color or black and white images at 640 × 480
pixels. The CompactFlash card holds approximately
118 standard image quality pictures without audio
recordings, but the image size is smaller and includes less
detail when enlarged. This setting is good for pictures that
Super Fine
Produces color or black and white images at
1600 × 1200 pixels with low compression. Your pictures
include greater detail, and the CompactFlash card holds
approximately 12 pictures. With less compression, super fine
images are better for enlarging.
HyPict
are viewed on screen or on the Web.
Produces color or black and white images at
1984 × 1488 pixels (interpolated) with moderate
Fine
compression. Your pictures include excellent detail, and the
CompactFlash card holds approximately 10 HyPict pictures.
Produces color or black and white images at
1600 × 1200 pixels, with moderate compression. Your
pictures include ample detail, and the CompactFlash card
holds approximately 25 pictures without audio recordings.
3-2 Using the Camera Buttons to Change Settings
These images are best for enlarging for 8 × 10-inch prints.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
Using the Flash
Flash Off
The flash is disabled, even when adequate lighting is
The camera’s built-in flash is effective within a range of 1.6
to 11.2 feet (0.5 to 3.4 m), or 6 inches to 1.6 feet (15 to
50 cm) when using the macro feature. Press the flash button
to cycle through the four flash settings.
not available. Use this setting for special effects,
where flash photography is prohibited, or for macro mode
3
close-ups.
Slow Synchronized Flash
NOTE
The camera dial must be turned to
,
, or
To light up the background as well as your subject,
.
An icon for each setting appears on the status display panel,
use the slow synchronized flash mode when taking
pictures at night. This option causes the aperture to stay
as shown below:
open longer, allowing more light to enter the camera.
Auto
NOTE
The flash goes off automatically whenever it’s needed
Slow synchronized flash is available only in the Program or
for adequate lighting (factory setting).
Manual user modes. See page 4-2 for information about changing
the user mode.
Forced Flash
The flash goes off with every picture you take. Use this
After you take a flash picture, the icon blinks until the flash is
setting to compensate for backlighting; for example,
fully recharged. Your flash setting remains in effect even after
when you are facing a light source.
you turn off the camera.
Using the Camera Buttons to Change Settings 3-3
A
B
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Follow these steps to take a single picture with the timer:
TIPS
◗
When you’re using the flash off setting, hold the camera
1
steady or use a tripod to avoid capturing blurry images.
◗
Secure the camera on a flat surface or on a tripod. (See
page A-4 for information on attaching the camera to a
tripod.)
When you’re taking pictures outdoors, make sure the sun is
at your back. In very bright light (at the beach or in snow, for
example), your pictures may come out too light. You can
adjust the exposure manually to darken an image before you
capture it. See page 4-22 for instructions. Alternatively, you
2
Open the lens cover.
3
Turn the camera’s dial to . Then wait until the photo
capture status light turns green.
4
Press the timer button
on the top of the camera. The
timer icon appears in the status display panel.
can use Image Expert or other image editing software to
correct over-exposure problems after you take the picture.
See Chapter 9 for details about editing photos.
Taking Pictures With the Timer
Setting the timer creates a 10-second delay between
the time you press the shutter button and the actual
image capture. This allows you to take a picture of yourself.
You can also combine continuous shooting with the timer
for delayed automatic capture of ten images in ten seconds.
This allows you to photograph yourself in motion. (See page
4-11 for more information.)
3-4 Using the Camera Buttons to Change Settings
timer button
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
5
Press the shutter button. The timer icon and the red
NOTE
timer light on the front of the camera flash slowly for
eight seconds. Then they flash rapidly for two seconds
◗
before the shutter is released.
◗
The camera beeps when the image is captured. The
status light on the back of the camera flashes green as the
PhotoPC 800 processes the image(s).
You can also use the LCD screens to adjust sensitivity, white
balance, and exposure. See Chapter 4 for details.
The camera dial must be turned to
,
, or
to change
3
settings using the camera buttons.
Adjusting the Sensitivity Setting
The camera’s high sensitivity settings let you take pictures in
NOTE
To cancel a picture after you’ve pressed the shutter button,
press the shutter button again, or press the
button.
Making Advanced Adjustments
You can also use the camera’s buttons to adjust the
sensitivity, white balance, and exposure settings. However,
you must be in Program or Manual mode to make these
adjustments. See page 4-2 for instructions on changing the
user mode.
low light or indoors without the flash. With these settings,
you can set the sensitivity from the camera’s standard ISO
equivalent of 100 to an ISO equivalent of 200 or 400.
You can also use the high and super high sensitivity settings
when taking pictures of fast-moving subjects, or when
shooting distant subjects with a flash. Since image quality is
lower when you use higher sensitivity settings, the standard
setting is recommended for most photos.
A
B
Using the Camera Buttons to Change Settings 3-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
Press the ISO button on the back of the camera to cycle
Adjusting the White Balance Setting
through the three sensitivity settings.
Normally the PhotoPC 800 adjusts the white balance of your
pictures automatically. This means that both outdoor and
indoor pictures have accurate colors, without a “bluish” or
“yellowish” appearance.
However, you can have the camera use a fixed white balance
for a warmer appearance under fluorescent lighting or for
special effects, such as a red-tinted sunset. You can also
customize the white balance setting.
ISO button
The arrow icons in the upper left corner of the status display
Press the W.B. button on the back of the camera to cycle
through the three white balance settings.
panel indicate the sensitivity setting:
The standard setting is equivalent to ISO 100. This
is the recommended setting for most photos.
The high sensitivity setting is equivalent to ISO
200.
The super high sensitivity setting is equivalent to
ISO 400.
3-6 Using the Camera Buttons to Change Settings
W.B. button
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
The setting, which appears in the status display panel next to
Adjusting the Exposure Setting
the W.B. mark, remains in effect while you take pictures.
Your camera normally adjusts exposure automatically.
However, if you want to lighten or darken a photo before
you take it, you can adjust the exposure manually.
white
balance
setting
3
Press the + or − button on the back of the camera to increase
or decrease the exposure setting. (The range for this setting is
−2.0 to +2.0.)
The PhotoPC 800 includes the following white balance
settings:
AUTO
Adjusts the white balance of your photos
automatically. This is the recommended setting
+ and − buttons
for most pictures.
FIX
Locks the white balance setting at 5200 °K.
(This setting is similar to normal daylight.)
CUST
Lets you define a custom white balance setting.
See page 4-21 for more information about
A
B
photographing with a user-defined white
balance.
Using the Camera Buttons to Change Settings 3-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
The setting appears in the status display panel next to
the +/− mark and remains in effect while you take pictures.
exposure setting
3-8 Using the Camera Buttons to Change Settings
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
.
4
Using the LCD Menus to Change
Settings
T
he LCD menus let you preview your pictures while
you make your camera settings. This chapter explains
4
the following:
FOR SALE
◗
Choosing the user mode
◗
Taking color or black and white pictures
◗
Taking quick shots
◗
Taking digital zoom pictures
◗
Taking close-ups with macro mode
◗
Taking digital panoramic pictures
◗
Using continuous and interval shooting
◗
Adding voice recordings to pictures
◗
Using programmed subject settings
◗
Adjusting the sensitivity setting
• 1995 Mitsubishi Montero
• Good condition
• Low Mileage
999-555-5555
Jim Jackson’s Auto Sales
Using the LCD Menus to Change Settings 4-1
A
B
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
◗
Adjusting the white balance setting
◗
Adjusting exposure
NOTE
If you’re using batteries, the camera shuts off automatically after
a designated period of inactivity. If the image on your LCD screen
◗
Adjusting the focus manually
◗
Changing the metering method
the back of the camera to “wake” the camera. If your dial is set
◗
Setting camera options (automatic power off, LCD
to
disappears and your camera dial is set to
or
, press any button on
, press the shutter button to wake the camera.
brightness, alert beep, language, and time and date)
Choosing the User Mode
top button
The PhotoPC 800 has three user modes to fit the needs of
beginner, intermediate, and expert photographers. Each
+
mode gives you a different amount of control over the
–
camera settings, whether you’re using the LCD screen or the
viewfinder to take pictures. To use the more advanced
bottom button
features, such as white balance and exposure adjustment, you
must be in Program or Manual mode.
MENU
ISO
W.B.
4-2 Using the LCD Menus to Change Settings
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
Full Auto The camera chooses settings for you. This mode,
spot or divided brightness metering system, and
which is the default, is recommended for the
beginning photographer. You can simply point
focus the camera to three feet, eight feet, or
infinity.
and shoot, or you can still adjust some basic
settings if you want (for example, image quality,
Follow these steps to choose the camera mode:
digital zoom, and macro or panoramic mode).
1
Push the camera dial lock in and turn the dial to
.
4
You see the SETUP menu.
Program This setting is recommended for the
intermediate photographer who wants a
moderate amount of control over the camera’s
functions. Programmed subject settings
(Normal, Sports, Portrait, and Landscape) tailor
user mode
your camera settings to the type of picture you’re
taking. You can also use the LCD menus to
make your own adjustments to sensitivity, white
balance, and exposure.
Manual
This setting is for experienced photographers
who want complete control over the camera’s
2
Press the + button to cycle through the three modes.
A
wide array of settings and features. In addition to
B
changing sensitivity and white balance, you can
adjust the shutter speed and aperture, choose a
Using the LCD Menus to Change Settings 4-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Taking Color or Black and White
Pictures
Taking Quick Shots
You also use the SETUP menu to switch between color and
seconds to process and save the image in the installed
black and white pictures.
memory card. In quick shot mode, the camera stores up to
10 images internally in temporary storage while you keep
NOTE
taking pictures. It saves the images to the CompactFlash card
after you’re done.
There is no difference between the file sizes of color and black
After taking a picture, the PhotoPC 800 normally takes a few
and white pictures when you take pictures with the LCD screen.
Follow these steps to use quick shot mode:
Follow these steps:
1
Turn the camera dial to
1
. You see the SETUP menu.
Turn the camera dial to . You see the SETUP menu.
(Normal Shot appears in the bottom right corner of
the screen.)
color/
monochrome
setting
2
Press the − button to change the setting.
4-4 Using the LCD Menus to Change Settings
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
2
Press the bottom button (next to Normal Shot) to
select Quick Shot.
3
Slide the lens cover switch to open the lens cover.
4
Turn the camera dial to
or
and wait until the
camera status light turns green. The image quality icon
NOTE
◗
You can’t use quick shot mode when battery power or
CompactFlash card memory is low.
◗
HyPict image quality is disabled in quick shot mode.
◗
When using quick shot mode, you can only make an audio
recording for the last image.
4
on the status display panel flashes, indicating that
quick shot mode is enabled.
5
Press and hold the shutter button to begin taking
pictures. When you’re finished, release the button.
The bracketed number on the status display panel
indicates the number of pictures temporarily saved to
Taking Digital Zoom Pictures
Digital zoom pictures are magnified two times (2×). This
format is like a digital version of telephoto. The automatic
cropping effect makes file sizes smaller, allowing you to store
more pictures in the digital zoom format.
the camera.
A
B
Using the LCD Menus to Change Settings 4-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
2
This setting is available for all user modes (Full Auto,
Program, and Manual).
1
Press the top button (next to the ×1).
The words DIGITAL ZOOM appear on your LCD
Open the lens cover and turn the camera dial to
.
You see the View menu. The current digital zoom
setting appears in the upper right corner.
briefly. A yellow frame appears around the previewed
image, and the digital zoom setting changes to ×2.
3
Press the shutter button halfway to lock the auto focus.
When the lens locks in focus, the camera status light
stops flashing and you see a green circle on the
digital zoom
setting
screen. If you want, you can reframe your picture while
you hold the button down.
4
Press the button all the way down to capture the image.
The zoom format remains active until you change it or turn
off the camera.
NOTE
This View menu illustrates what you see if your user mode is
set to Full Auto. Your View menu will look different if the
user mode is set to Program or Manual.
4-6 Using the LCD Menus to Change Settings
NOTE
Since the digital zoom mode crops the image and magnifies it, it’s
best to print the image in a smaller format.
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
Taking Close-Ups With Macro Mode
2
Press the bottom button (next to the current frame
You can use the camera’s macro mode to take pictures as
setting).
close as 6 inches (15 cm). This setting is available for all user
modes (Full Auto, Program, and Manual).
For a few seconds, the word MACRO appears on the
LCD screen, and a green frame appears around the
Follow these steps:
previewed image. Also, the macro mode icon
appears
in the lower right corner of the screen.
1
Open the lens cover and turn the camera dial to
see the View menu.
4
. You
3
Press the shutter button halfway to lock the auto focus.
When the lens locks in focus, the camera status light
stops flashing and you see a green circle
on the
screen. If you want, you can reframe your picture while
you hold the button down.
4
frame setting
Press the button all the way down to capture the image.
Macro mode remains active until you change it or turn off
the camera.
A
NOTE
This View menu illustrates what you see if your user mode is
set to Full Auto. Your View menu will look different if the
B
user mode is set to Program or Manual.
Using the LCD Menus to Change Settings 4-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
You can take panoramic pictures using any user mode (Full
NOTE
When you take macro close-ups, you should use a tripod (as
described in Appendix A) and disable the flash. Otherwise, your
pictures may appear blurry and washed out.
Taking Digital Panoramic Pictures
Auto, Program, or Manual). Follow these steps:
1
Open the lens cover and turn the camera dial to
.
You see the View menu. The current frame setting
appears in the lower right corner.
Images in the panoramic format are long and narrow,
although they are not captured at a wider angle than normal
images. Strips at the top and bottom of the image area are
cropped out. Smaller file sizes mean you can store more
pictures in the panorama format.
frame setting
NOTE
You can’t select standard
image quality when taking
panoramic pictures. For more information about image quality,
see page 3-1.
NOTE
This View menu illustrates what you see if your user mode is
set to Full Auto. Your View menu will look different if the
user mode is set to Program or Manual.
4-8 Using the LCD Menus to Change Settings
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
2
Press the bottom button (next to the current setting) to
The following examples show the same subject captured in
cycle through the frame settings (Normal Frame,
Macro, and Panorama).
normal, digital zoom, and digital panorama formats:
For a few seconds, the word PANORAMA appears on
the LCD screen, and a black frame appears around the
4
previewed image. Also, the panorama mode icon
appears in the lower right corner of the screen.
3
Press the shutter button halfway to lock the auto focus.
normal
digital zoom
When the lens locks in focus, the camera status light
on the
stops flashing and you see a green circle
screen. If you want, you can reframe your picture while
you hold the button down.
4
Press the button all the way down to capture the image.
digital panorama
The Panorama format remains active until you change it or
A
turn off the camera.
B
Using the LCD Menus to Change Settings 4-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
Continuous Shooting
You see a preview of your picture on the LCD screen,
with a red frame around it. CONTINUOUS appears on
the screen.
In this mode, you can take two standard or fine
resolution pictures each second, with up to ten pictures in
sequence (or one super fine resolution picture per second,
with up to eight pictures in sequence). You can capture a
3
Center your subject in the red frame.
complex motion, such as a golf swing, in a series of steps to
create animation sequences for the Internet, screen savers, or
4
Press and hold the shutter button all the way down. The
presentations. Continuous shooting is available for all user
modes.
camera beeps as it captures each picture.
5
When the camera has captured the first sequence of
pictures, it stops beeping and the camera status light
flashes. Release the shutter button.
NOTE
You can’t use the flash for continuous shooting, so make sure
you have adequate lighting for your pictures. In addition, you can’t
NOTE
If you continue to hold down the shutter button after the first
select the HyPict image quality setting.
sequence of pictures, the camera will take a second sequence.
1
Make sure you are at least 20 inches (50 cm) away from
your subject.
2
Open the lens cover, then turn the camera dial to
Wait until the camera status light turns green.
4-10 Using the LCD Menus to Change Settings
.
The camera will continue to take pictures until the memory card
is full.
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
Continuous Shooting Using the Timer
You can also combine continuous shooting with the timer
for delayed automatic capture of a series of images. This
allows you to photograph yourself in motion.
NOTE
4
timer button
You can capture 10 standard or fine resolution images or 8 super
fine resolution images in eight seconds.
1
The timer icon
page A-4 for information on attaching the camera to a
indicate that the timer is enabled.
tripod.)
2
appears on the status display panel to
Secure the camera on a flat surface or on a tripod. (See
Open the lens cover, then turn the camera dial to
Wait until the camera status light turns green.
5
.
You see a preview of your picture on the LCD screen,
Press the shutter button.
You have 10 seconds to get ready for “action” in front of
the camera.
with a red frame around it. CONTINUOUS appears on
The timer icon and the red timer light on the front of
the camera flash slowly for eight seconds. Then they
the screen.
flash rapidly for two seconds before the shutter is
3
Center your subject in the red frame.
released.
4
Press the timer button.
A
B
Using the LCD Menus to Change Settings 4-11
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
The camera beeps each time it captures an image, and
2
You see a preview of your picture on the LCD screen,
with a red frame around it. CONTINUOUS appears on
Interval Shooting
Your camera lets you set a time interval from 10 seconds to
24 hours. Interval shooting is available for all user modes.
.
Wait until the camera status light turns green.
the timer light on the front of the camera flashes as the
images are processed.
You can use this time lapse feature to capture scenes that
change over time, such as a sunset or a busy street corner.
Open the lens cover, then turn the camera dial to
the screen.
3
Hold down the MENU button (under PRESS or
HOLD) until you see the following screen:
NOTE
When you’re adding audio recordings or taking pictures with
HyPict image quality, the shortest time interval available is 20
seconds.
time lapse
interval setting
Follow these steps to use the time lapse feature:
1
Secure the camera on a flat surface or on a tripod. (See
page A-4 for information on attaching the camera to a
tripod.)
4-12 Using the LCD Menus to Change Settings
The current setting for the time lapse interval (hours,
minutes, and seconds) appears in the center of the
screen, with seconds highlighted.
Altair.book Page 13 Thursday, July 1, 1999 3:33 PM
4
Press the + or − button (next to the up and down
Adding Voice Recordings to Pictures
arrows) to change the highlighted setting, then press the
ISO button (under the left arrow) to move to the next
Your camera has a built-in microphone that lets you add a
setting and repeat the process. Continue until you’ve set
the correct interval.
make a recording immediately after shooting a photo, or add
it later. (For information about adding a recording later, see
voice recording of up to 10 seconds to each photo. You can
page 5-8.) You can make voice recordings in any user mode.
4
NOTE
You can also choose the maximum interval (24 hours) by
pressing the top button (next to Max Interval), or the
minimum interval (10 seconds) by pressing the bottom
button (next to Min Interval).
5
NOTE
You can’t record a message when taking a picture with the
optical viewfinder or when taking a picture in Quick Shot mode.
Press the shutter button to take the first picture.
The camera turns off automatically after you take the
first picture, then turns on again after the selected
interval to take the next photo.
6
microphone
To stop taking pictures, turn the camera’s dial to Off.
A
B
Using the LCD Menus to Change Settings 4-13
Altair.book Page 14 Thursday, July 1, 1999 3:33 PM
Follow these steps to add a recording right after taking a
4
Open the lens cover and turn the camera dial to
.
Center the subject on the LCD screen.
picture:
1
Turn the camera dial to
to display the SETUP menu.
5
2
Press the MENU button (under Camera SETUP). You
see the Camera SETUP menu. The current audio setting
Press the shutter button halfway down to lock the auto
focus.
6
When the camera status light stops flashing and you see
appears at the bottom of the screen under Rec.
a green circle
on the screen, press the shutter button
the rest of the way down.
7
Hold the camera still until it beeps. Then release the
shutter button.
After a moment, you see a confirmation message. Then
you see the message Sound recording... and a
countdown of the recording time.
current audio setting
3
Press the ISO button (under Rec) to choose a different
setting. You can record a 3, 5, or 10-second message, or
turn recording off.
4-14 Using the LCD Menus to Change Settings
8
Speak clearly into the microphone. You see another
confirmation message indicating that the recording was
successful.
Altair.book Page 15 Thursday, July 1, 1999 3:33 PM
◗
NOTE
Recommended for portraits. Uses the
Portrait
following settings: spot metering,
aperture fixed at f/2.4.
Even if you don’t speak into the microphone, your camera records
ambient noise when recording is turned on, and your images take
up more space on the memory card. To fit more images on your
◗
Landscape
memory card, make sure you turn recording off when you no
longer want to use it.
Recommended for landscapes or scenery.
Uses the following settings: matrix
metering, aperture set to f/8.0. (The
aperture automatically changes to f/2.4
Using Programmed Subject Settings
when the subject is dim.)
The Program user mode provides four programmed settings
that let you choose the type of shot you’re taking. The
Follow these steps to use programmed subject settings:
camera automatically assigns the optimum exposure,
1
metering method, and sensitivity for your subject.
◗
Normal
4
Set the camera to Program user mode. (See page 4-2 for
instructions.)
Appropriate for most photographs. Uses
the following settings: auto exposure,
matrix metering.
◗
Sports
Recommended for action photographs.
Uses the following settings: high shutter
speed, automatic sensitivity, matrix
A
metering.
B
Using the LCD Menus to Change Settings 4-15
Altair.book Page 16 Thursday, July 1, 1999 3:33 PM
2
Open the lens cover and turn the camera dial to
. You
4
see the View menu.
Press the ISO button to cycle through the four subject
settings.
5
When you’ve made your setting, press the MENU
button (under BACK) to save it.
Your subject setting appears in the upper left corner of
the View menu.
subject
setting
3
Hold down the MENU button (under PRESS or
HOLD) until you see the following screen:
6
subject setting
4-16 Using the LCD Menus to Change Settings
Take your picture. (See page 2-6 for instructions.)
Altair.book Page 17 Thursday, July 1, 1999 3:33 PM
Adjusting the Sensitivity Setting
The high sensitivity setting is equivalent to
If you’ve set the user mode to Program or Manual, you can
ISO 200.
use the LCD screens to adjust the sensitivity setting. (You
The super high sensitivity setting is equivalent to
ISO 400.
can also use the camera’s ISO button to adjust this setting.
See page 3-5.)
4
Follow these steps to adjust sensitivity:
With the PhotoPC 800’s high sensitivity settings, you can
take pictures of fast-moving subjects, or indoor pictures
without a flash. You can set the sensitivity from the camera’s
standard ISO equivalent of 100 to an ISO equivalent of 200
or 400.
1
Make sure the camera is set to Program or Manual user
mode. (See page 4-2 for instructions.)
2
Open the lens cover and turn the camera dial to
. You
see the View menu.
NOTE
Since image quality is lower when you use high sensitivity
settings, the standard setting is recommended for most pictures.
The arrow icons above the ISO button indicate the
sensitivity setting:
The standard setting is equivalent to ISO 100. This
is the recommended setting for most pictures.
A
sensitivity setting
Using the LCD Menus to Change Settings 4-17
B
Altair.book Page 18 Thursday, July 1, 1999 3:33 PM
NOTE
This View menu illustrates what you see if your user mode is
set to Program. Your View menu will look slightly different if
the user mode is set to Manual.
3
If user mode is set to Manual, hold down the MENU
button (under PRESS or HOLD) until you see the
following screen. Press the ISO button to change the
sensitivity setting, then press the MENU button to save
your setting.
Do one of the following:
If user mode is set to Program, the current sensitivity
setting appears above the ISO button. (See the previous
illustration.) Press the ISO button to change the
sensitivity setting.
sensitivity setting
Adjusting the White Balance Setting
Although the PhotoPC 800 adjusts white balance for you
automatically to ensure color accuracy, you may sometimes
want to change this setting for special effects (for example, to
retain the red tints in a sunset).
4-18 Using the LCD Menus to Change Settings
Altair.book Page 19 Thursday, July 1, 1999 3:33 PM
The PhotoPC 800 includes the following white balance
Photographing With Fixed White Balance
settings:
The fixed white balance setting gives your pictures a warmer
AUTO
Adjusts the white balance of your pictures
automatically. This is the recommended setting
for most pictures.
FIX
Locks the white balance setting at 5200 °K.
CUST
Lets you customize the white balance setting.
appearance under fluorescent lighting. It’s also a good choice
for retaining the reds in a sunset.
5200 °K:
1
Make sure the camera is set to Program or Manual user
mode. (See page 4-2 for instructions.)
2
Open the lens cover and turn the camera dial to
see the View menu.
See page 4-21 for details.
You must be in Program or Manual mode to adjust the white
balance setting. See page 4-2 for information about changing
4
Follow these steps to lock the white balance setting at
. You
the user mode.
NOTE
If you’re using the viewfinder, you can also press the W.B. button
to change the white balance. See page 3-6 for details.
A
B
Using the LCD Menus to Change Settings 4-19
Altair.book Page 20 Thursday, July 1, 1999 3:33 PM
3
Do one of the following:
If user mode is set to Manual, hold down the MENU
If user mode is set to Program, the current white balance
button (under PRESS or HOLD) until you see the
following screen. Press the W.B. button to select FIX,
setting appears above the W.B. button. Press the W.B.
button to select FIX.
then press the MENU button (under Back) to save your
setting.
white balance setting
white balance setting
4-20 Using the LCD Menus to Change Settings
Altair.book Page 21 Thursday, July 1, 1999 3:33 PM
Photographing With User Defined White
Balance
4
Press the bottom button (next to the entry New W/B).
You see the following screen:
Follow these steps to customize the white balance setting:
1
2
Turn the camera dial to to display the SETUP menu.
If necessary, change to Program or Manual user mode.
4
Press the MENU button (under Camera SETUP) to
go to the Camera SETUP menu.
5
Press the bottom button (next to Yes) to save a new
white balance setting.
You see a message instructing you to press the shutter
button to set a new white balance.
6
3
Focus the camera on a piece of white paper, or some
other object to set white balance by, and press the
Open the lens cover.
A
shutter button to save the setting.
7
Open the lens cover and turn the camera dial to
see the View menu.
. You
Using the LCD Menus to Change Settings 4-21
B
Altair.book Page 22 Thursday, July 1, 1999 3:33 PM
8
Do one of the following:
Adjusting Exposure
If user mode is set to Program, the current white balance
Your camera normally adjusts exposure automatically.
setting appears above the W.B. button. Press the W.B.
button to select CUSTOM.
However, you may want to increase the exposure setting if
If user mode is set to Manual, hold down the MENU
snow on a sunny day. Similarly, you may want to decrease it
if you want to darken the picture, or if you’re taking pictures
button (under PRESS or HOLD) until you see the
you want to lighten your picture or if you’re taking pictures
of an object against a bright background, such as sand or
following screen. Press the W.B. button to select
CUSTOM, then press the MENU button (under Back)
against a dark background.
to save your setting.
With the PhotoPC 800, you can select predefined exposure
settings, or you can fine-tune the exposure manually by
setting the shutter speed and aperture setting.
NOTE
If you’re using the viewfinder, you can also use the camera’s
controls to make predefined exposure adjustments. See page 3-7
for instructions.
white balance setting
4-22 Using the LCD Menus to Change Settings
Altair.book Page 23 Thursday, July 1, 1999 3:33 PM
Making Predefined Exposure Adjustments
In Manual mode, press the ISO button (under
Follow these steps to make predefined exposure adjustments:
Exposure) to select AUTO, then press the + button to
1
increase the exposure setting, or the − button to decrease
Make sure that the camera is set to Program or Manual
user mode. (See page 4-2 for details.)
2
Open the lens cover and turn the camera dial to
3
Do one of the following:
it. You can choose from 21 settings in increments of 0.2,
from −2.0 to +2.0 EV.
.
In Program mode, press the + button (next to the up
arrow) to increase the exposure setting, or the − button
4
adjust
predefined
exposure
settings
(next to the down arrow) to decrease it. You can make
nine different settings in increments of 0.5, from
−2.0 to +2.0 EV (Exposure Value).
set exposure mode to AUTO
NOTE
Exposure Value is a combination of shutter speed and aperture
exposure
setting
setting.
A
B
Using the LCD Menus to Change Settings 4-23
Altair.book Page 24 Thursday, July 1, 1999 3:33 PM
Making Advanced Exposure Adjustments
4
Press the + button (next to the up arrow) to increase
adjusting the shutter speed and aperture.
shutter speed, or the − button (next to the down arrow)
to decrease it.
Follow these steps to set the shutter speed and aperture:
NOTE
Experienced photographers can set the exposure manually by
1
When the flash is set to automatic or forced flash, you can
Make sure that the camera is set to Manual user mode.
(See page 4-2 for details.)
2
Open the lens cover and turn the camera dial to
3
Press the ISO button (under Exposure) to change the
select shutter speeds from 1/30 to 1/750. When the flash is
turned off, you can select shutter speeds from 1/2 to 1/750.
See page 3-3 for instructions on setting the flash.
.
5
exposure mode to MANUAL.
Press the W.B. button to change the aperture setting.
(You can choose either F2.4 or F8.)
Adjusting the Focus
The PhotoPC 800 lets you adjust the distance of the focal
set shutter
speed
point. Follow these steps:
1
Make sure that the camera is set to Manual user mode.
(See page 4-2 for details.)
2
set exposure mode to MANUAL
4-24 Using the LCD Menus to Change Settings
Open the lens cover and turn the camera dial to
.
Altair.book Page 25 Thursday, July 1, 1999 3:33 PM
3
4
If you want to use the macro feature or take panoramas,
If the camera is set to Normal Frame or Panorama,
press the button next to Normal Frame until Macro
or Panorama appears in the center of the screen.
you can choose from the following settings:
Hold down the MENU button (under PRESS or
HOLD) until the following screen appears:
AF
The camera determines the focus automatically.
Focal point is about three feet.
4
Focal point is about 10 feet.
Focal point is infinity (∞).
focus setting
If you’re using the macro feature, you can choose a
setting from 1 to 10, where 1 is the closest possible
focus.
Changing the Metering Method
5
Press the + or − button (next to the up and down
arrows) to select a manual focus setting.
If you’re using Manual mode, your camera lets you choose
between matrix metering and spot metering.
With matrix metering, the camera automatically measures
the available light and determines the correct exposure. If
you’re an advanced photographer, you can use spot metering
to choose a point that the camera samples to determine
exposure.
Using the LCD Menus to Change Settings 4-25
A
B
Altair.book Page 26 Thursday, July 1, 1999 3:33 PM
Follow these steps to change the metering system:
Setting Camera Options
1
Make sure that the camera is set to Manual user mode.
You can change the settings of several camera options,
(See page 4-2 for details.)
including the automatic power off feature, the LCD screen’s
2
Open the lens cover and turn the camera dial to
3
Hold down the MENU button (under PRESS or
.
HOLD) until you see the following screen. The current
metering setting is in the lower right corner.
brightness, and when and whether the camera beeps. You
can also reset the camera’s clock and language.
NOTE
You can also set the camera’s clock and automatic power off
feature from your computer. See Chapter 10 for details.
Setting the Automatic Power Off Feature
The automatic power off feature saves battery power by
automatically turning your camera off when it’s idle for a
designated period of time. You can set the camera to turn off
metering
setting
4
Press the bottom button (beside Metering) to change
the setting.
5
Press the MENU button (under BACK) to save your
setting.
4-26 Using the LCD Menus to Change Settings
after 10 seconds, 30 seconds, one minute, or three minutes.
Altair.book Page 27 Thursday, July 1, 1999 3:33 PM
2
Follow these steps to change the power off interval:
1
Push the camera dial lock in and turn the dial to
Press the MENU button (below Camera SETUP) to
go to the Camera SETUP menu. The current power off
setting appears in the upper right corner of the screen.
. You
see the SETUP menu.
power off
setting
3
4
Press the top button (next to the current setting) to
select a new setting.
NOTE
Automatic power off is only in effect when you’re using batteries
to power the camera.
A
B
Using the LCD Menus to Change Settings 4-27
Altair.book Page 28 Thursday, July 1, 1999 3:33 PM
Setting the LCD Brightness
Setting the Alert Beep
To adjust the brightness of the LCD screen, follow these
Normally, the camera’s alert beep lets you know when an
steps:
image has been captured. However, you can turn the alert
beep off, or set the camera to beep whenever you press any of
1
Turn the camera dial to to display the SETUP menu.
Then press the MENU button (under Camera
SETUP). You see the Camera SETUP menu.
its buttons.
To set the alert beep, follow these steps:
1
Turn the camera dial to to display the SETUP menu.
Then press the MENU button (below Camera
SETUP). You see the Camera SETUP menu.
2
Press the + or − button (next to the up and down
arrows) to adjust the screen brightness.
4-28 Using the LCD Menus to Change Settings
Altair.book Page 29 Thursday, July 1, 1999 3:33 PM
2
Press the W.B. button (under Beep) to cycle through
1
these choices:
◗
Shutter
The camera beeps when an image is
captured.
◗
Never
Turns the beep off.
◗
Always
The camera beeps whenever you press
a button.
Turn the camera dial to
to display the SETUP menu.
You see the camera date and time setting in the upper
right corner of the screen.
camera date
and time
setting
4
Setting the Time and Date
The camera remembers the time and date settings you made
when you formatted your memory card, unless it goes
without battery power for more than a couple of hours. If
2
Press the top button (next to the setting) to display the
following screen. The month is highlighted in red.
you need to reset the time and date for any reason, follow
these steps:
A
B
Using the LCD Menus to Change Settings 4-29
Altair.book Page 30 Thursday, July 1, 1999 3:33 PM
3
Press the + or − button (next to the up and down
2
arrows) to adjust the setting, then press the W.B. button
(under the right arrow) to highlight the day.
4
Press the ISO button (under the
icon) to go to the
language setting screen.
Repeat step 3 for each item you want to change. (To
return to a previous setting, press the ISO button.)
5
When you’re done, press the MENU button (under
BACK) to save the setting and return to the SETUP
menu.
Setting the Language
3
You can choose from two languages for information
displayed on the LCD screen.
Follow these steps to change the language setting:
1
Turn the camera dial to
to display the SETUP menu.
4-30 Using the LCD Menus to Change Settings
If necessary, press the W.B. button (under the right
arrow) to highlight ENG.
4
Press the MENU button (under BACK) to save the
setting and return to the SETUP menu.
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
.
5
Playing Back Photos
T
he LCD screen lets you play back your pictures oneby-one or in groups of four or nine. You can magnify
5
or delete selected pictures and customize playback features.
You can also view your pictures on a television as easily as on
the camera’s screen. This chapter explains the following:
◗
Playing back pictures one-by-one or several pictures
at a time
◗
Deleting pictures
◗
Locking pictures
◗
Adding and deleting audio recordings
◗
Magnifying pictures
◗
Viewing detailed information about a picture
◗
Playing pictures as a slide show
◗
Playing back pictures on TV
A
Playing Back Photos 5-1
B
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Playing Back Pictures One by One
top button
+
When you set the camera dial to
, you see the last picture
you took on the LCD screen:
–
bottom button
MENU
ISO
picture number
W.B.
NOTE
After a designated period of inactivity, the camera
automatically shuts off to conserve battery power. If the
image on your LCD screen disappears, press any button on
the back of the camera to “wake” the camera.
display multiple images
Press the + button (next to the right arrow) to display the
earliest picture taken. You can continue pressing the +
button to view your pictures in order. Press the − button
(next to the left arrow) to move backward through your
pictures.
5-2 Playing Back Photos
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
Playing Back Multiple Pictures
3
ISO button (under 1x9) again.
You can play back your pictures in Multi mode to view small
“thumbnail” versions of either four or nine pictures at once.
If you want to display nine pictures at once, press the
4
Follow these steps to play back multiple pictures:
Press the + and − buttons to move the white selection
frame through the images on screen, or hold one of these
buttons down to move through the images quickly.
1
2
Turn the camera dial to
. You see the last picture you
took on the LCD screen.
When the frame passes the first or last image of the
Press the ISO button (below Multi).
current group, the previous or next three images are
displayed in the group.
Small thumbnail images of the last four pictures you
took appear on the screen, with the currently selected
image framed in white.
5
5
To switch back to displaying one picture at a time, press
the ISO button again.
press the + or −
button to move
through images
A
B
Playing Back Photos 5-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Deleting Pictures
NOTE
The LCD screen provides two different methods for deleting
To make choosing images easier, you can display four or
images after you play them back:
nine images at a time by pressing the ISO button once or
twice.
◗
You can delete the currently displayed picture
◗
You can select multiple pictures for deletion, or “lock”
2
Press the W.B. button (under Delete). A confirmation
message appears.
3
Press the top button (next to Yes) to delete the image,
(protect) them from deletion
You can also delete images through your software when the
camera is connected to your computer. For instructions, see
Chapter 6.
or the bottom button (next to No) to cancel.
NOTE
Deleting the Currently Displayed Picture
If you try to delete a locked image
Make sure the camera dial is set to
steps:
message. Press any button to clear the message. See pages 5-6
1
, then follow these
Press the + or − button (next to the right and left arrows)
to display the image you want to delete.
5-4 Playing Back Photos
, you see a warning
for instructions on locking and unlocking images in the camera.
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Deleting All Pictures
Deleting Selected Pictures
To delete all the images from your memory card, make sure
Make sure the camera dial is set to
the camera dial is set to
1
, then follow these steps:
1
Press the bottom button (next to Select Image). Then
press the top button (next to Select All) to select all the
images in your card.
2
Press the ISO button (under Delete) to delete the
images. A confirmation message appears.
3
Press the top button (next to Yes) to delete the images,
or the bottom button (next to No) to cancel.
, then follow these steps:
Press the ISO button (under Multi) once to display four
pictures on the screen, or twice to display nine. A white
frame appears around one of the pictures.
2
Press the button next to Select Image. You see the
following on your screen:
5
NOTE
If any images are locked, you see a message asking if you want
to delete them. Press the button next to No to delete only the
unlocked images, or next to Yes to delete the locked images too.
See page 5-8 for instructions on unlocking images.
A
B
Playing Back Photos 5-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
3
Press the + or − button (next to the right and left arrows)
Locking Pictures
to move the frame to an image you want to erase. Then
press the bottom button (next to Select). A red frame
The lock feature allows you to keep your images from being
accidentally deleted. You can lock selected images or all the
images in the camera. Make sure the camera dial is set to ,
appears around the image and the word Select changes
to Release.
then follow these steps to lock pictures:
NOTE
1
If you change your mind, press the button next to Release to
Press the ISO button (under Multi) once to display four
pictures on the screen, or twice to display nine. A white
deselect the image.
frame appears around one of the pictures.
4
Repeat step 3 to select any additional images.
5
After you’ve finished selecting images, press the ISO
button (under Delete) to delete them.
A confirmation message appears. Press the top button
(next to Yes) to delete the selected images, or the
bottom button (next to No) to cancel.
5-6 Playing Back Photos
2
Press the bottom button (next to Select Image). You
see the following on your screen:
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
3
Do one of the following:
◗
4
Press the W.B. button (under the padlock icon). You see
the following on your screen:
If you want to lock all images, press the top button
(next to Select All). (If you change your mind,
press the same button to deselect all images.)
◗
If you want to lock just one or some of the images,
press the + or − button to move the frame to an
5
image you want to lock. Then press the bottom
button (next to Select). (If you change your mind,
press the button next to Release to deselect the
image.) Repeat this step for each image you want to
lock.
5
Press the button next to Lock.
A padlock icon appears in the upper left corner of each
A red frame appears around each image selected.
locked image.
6
Press the MENU button (under BACK) to save your
settings.
A
B
Playing Back Photos 5-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
3
Unlocking Pictures
After you have locked some of your pictures, you can unlock
The selected images are unlocked. If an image is
selected pictures or all the pictures in the camera.
Make sure the camera dial is set to
1
2
Press the bottom button (next to Release).
successfully unlocked, the padlock icon disappears from
the upper left corner of its frame.
, then follow these steps:
Repeat steps 1 through 3 of “Locking Pictures” to select
the images you want to unlock.
4
Press the W.B. button (under the padlock icon). You see
Adding Audio Recordings
the following:
You can add audio recordings to images stored on your
memory card.
Press the MENU button (under BACK) to save your
settings.
NOTE
You can’t add audio recordings to images taken in quick shot
mode.
5-8 Playing Back Photos
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
Follow these steps to add a recording to an existing image:
1
Turn the camera dial to
3
Hold down the MENU button (under HOLD to
NEXT) until the screen changes, then press the top
to go to playback mode.
button (next to RECORD). You see the following:
5
2
Press the + or − button (next to the right and left arrows)
to move to the photo to which you want to add a
recording. (If you’re displaying multiple images, you’ll
see a white frame around the currently selected photo.)
4
Press the button next to the desired recording time. A
countdown of the recording time appears on the screen.
NOTE
If there’s already a message on the selected photo, a
confirmation message appears after you choose the
recording time. To erase the old recording and make a new
one, press the top button (next to Yes). Or press the bottom
A
button (next to No) to cancel.
B
Playing Back Photos 5-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
5
Speak clearly into the microphone on the back of the
3
Hold down the MENU button (under HOLD to
NEXT) until you see the following:
camera.
A microphone icon appears in the upper left corner of
the image to indicate that a recording has been added.
Deleting Audio Recordings
You can also delete audio recordings that you’ve added to the
pictures on your memory card.
Make sure your camera dial is set to
steps:
1
, then follow these
Press the ISO button (under Multi) once to display four
pictures on the screen, or twice to display nine. A white
frame appears around one of the pictures.
2
Use the + or − button (next to the right and left arrows)
to move to an image whose attached recording you want
to erase. (You’ll see a microphone icon in the upper left
corner if the image has a recording attached.)
5-10 Playing Back Photos
4
Press the button next to RECORD. You see the
following on your screen:
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
5
Press the ISO button (under Sound Delete) to delete
The sections of your image that can be viewed are
the recording for this picture. A message appears asking
you to confirm the deletion.
demonstrated in the figure below:
The center
section is
magnified first
NOTE
If you see a message that the selected image is locked,
press the button next to Unlock to unlock it.
6
7
Press the button next to Yes to confirm, or No to
cancel.
Make sure the camera dial is set to
1
to the playback menu.
To magnify the currently displayed image, press the top
A magnified view of the center section of the picture
appears. An icon in the top left corner of the screen
Magnifying a Picture
indicates which section of the image is currently
You can zoom in to magnify a portion of your image on the
LCD screen and view it in greater detail. Then you can use
sections for panoramic images).
5
button (next to the magnifying glass icon).
Press the MENU button (under BACK) twice to return
the camera’s buttons to scroll the image and display another
section (up to nine sections for regular images and three
, and follow these steps:
displayed.
2
To view different sections of the magnified image, press
the + and − buttons (next to the up and down arrows) to
move up or down, or the ISO and W.B. buttons (next
to the left and right arrows) to move left or right.
Playing Back Photos 5-11
A
B
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
You see the following screen:
NOTE
When you magnify a panoramic picture, it’s divided into
three parts. You can only scroll left and right.
3
To exit the magnification screen, press the MENU
button (next to BACK).
Viewing Picture Information
You can use the LCD screen to view detailed information
about individual images, including date and time taken,
2
shutter speed, exposure settings, aperture and white balance
settings, and metering method. To display image
Press the W.B. button (below INFO) to display
information for the currently selected image.
information, follow these steps:
1
Turn the camera dial to
, then hold down the MENU
button (under HOLD to NEXT).
3
5-12 Playing Back Photos
Press the MENU button (under BACK) to exit the
picture information screen.
Altair.book Page 13 Thursday, July 1, 1999 3:33 PM
Playing Your Pictures as a Slide
Show
2
Press the bottom button (next to SLIDE SHOW). You
see the following screen:
You can use the LCD screen to play back your pictures in a
continuous “slide show.” You can even control the slide
show’s speed and pauses.
slide
show
speed
Follow these steps:
1
Turn the camera dial to . Then hold down the MENU
button under HOLD to NEXT) until the following
5
screen appears:
3
Press the + button to select the slide show speed. (You
can have the image change automatically every 3, 5, or
10 seconds, or you can choose to change the images
manually.)
NOTE
You can also rotate the images, or exclude certain images
from your slide show. See the following sections for
A
instructions.
B
Playing Back Photos 5-13
Altair.book Page 14 Thursday, July 1, 1999 3:33 PM
4
Press the bottom button (next to Start) to begin the
2
slide show.
Press the bottom button (next to SLIDE SHOW). You
see the following screen:
To pause the slide show, press the MENU button; then
press the MENU button again to restart it. While the
slide show is paused, you can view the last image by
pressing the ISO button (under BACK).
To stop the slide show, press the bottom button (next to
Quit).
Excluding Pictures From a Slide Show
All pictures saved in your camera’s memory card are
automatically included in the slide show. To exclude any
pictures from the slide show, follow these steps:
1
Turn the camera dial to . Then hold down the MENU
button (next to HOLD to NEXT) until you see the next
screen.
5-14 Playing Back Photos
3
Press the − button (next to SlideSelect). The following
screen appears:
Altair.book Page 15 Thursday, July 1, 1999 3:33 PM
4
5
Press the + or − button (next to the right and left arrows)
Rotating Pictures in a Slide Show
to select the picture you want to exclude from the slide
show. (If you want, press the ISO button to display
You can display pictures in your slide show rotated 90
multiple pictures.)
degrees to the right or left. To rotate a picture, follow these
steps:
Do one of the following:
1
◗
Press the bottom button (next to Exclude) to
exclude the selected picture.
◗
Turn the camera’s dial switch to
to display the
playback menu, then hold down the MENU button
(under HOLD to NEXT) until you see the next screen.
5
Press the top button (next to Excld All) to exclude
all pictures.
NOTE
If you change your mind, move the white frame to the
picture you want to include again and press the bottom
button (next to Select). Or press the top button (next to
Select All) to include all pictures.
6
When you’re finished, press the MENU button twice to
A
return to the playback menu.
B
Playing Back Photos 5-15
Altair.book Page 16 Thursday, July 1, 1999 3:33 PM
2
Press the bottom button (next to SLIDE SHOW). You
4
see the following:
Press the + or − button (next to the right and left arrows)
to frame the image you want to rotate. Then press the
bottom button (next to Select) to select the image.
NOTE
To make it easier to view your picture, press the ISO button
to display multiple images, then use the + or − button to
select an image.
5
3
To rotate the image 90 degrees to the right, press the
W.B. button (under Rotate) once. An orientation icon
appears in the upper left corner of the screen
Press the − button (next to SlideSelect) to display the
indicating that the picture will be rotated to the right
when displayed in the slide show.
following:
To rotate the image 90 degrees to the left, press the
W.B. button twice. A left orientation icon
appears in
the upper left corner of the screen.
6
Repeat steps 4 and 5 to rotate more pictures. When
you’re finished, press the MENU button (under BACK)
to save your changes.
5-16 Playing Back Photos
Altair.book Page 17 Thursday, July 1, 1999 3:33 PM
Playing Back Pictures on TV
You can display your pictures on a regular television
or VCR by using the video cable that came with your
2
Open the camera’s connector cover and connect the
black end of the video cable to the Video Out port, as
shown.
PhotoPC 800.
TIP
You can videotape your pictures to share them without using a
5
computer. After you connect the camera to your VCR, press the
Record button on the VCR and use the camera’s slide show
feature, as described on page 5-13.
Follow these steps to play back your pictures on TV:
1
Make sure the camera and TV (and VCR) are turned off.
A
B
Playing Back Photos 5-17
Altair.book Page 18 Thursday, July 1, 1999 3:33 PM
3
Connect the yellow end of the cable to the VIDEO IN
port on the television or VCR.
4
Turn on the TV (and VCR) and switch to the correct
video mode.
5-18 Playing Back Photos
5
Altair.book Page 19 Thursday, July 1, 1999 3:33 PM
6
urn the camera dial to
. The last picture you took
appears on the TV screen. You can use all of the
camera’s playback features when your pictures are
displayed on TV.
NOTE
Using the optional AC adapter is highly recommended when you
5
play back your pictures on a TV. See page A-2 for instructions and
ordering information.
A
B
Playing Back Photos 5-19
Altair.book Page 20 Thursday, July 1, 1999 3:33 PM
5-20 Playing Back Photos
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
.
6
Getting Photos Into Your Computer
W
Connecting the Camera
presentations, or in just about anything you create on your
computer. This chapter describes the following:
◗
hen you’re finished taking pictures, you can connect
the camera to your computer and transfer the
Note the following before you start:
images. Then you can use the pictures on your Web site, in
If you have the optional AC adapter, you can conserve
6
battery life by using it when you connect the camera to
your computer. See page A-2 for instructions.
◗
Connecting the camera
◗
Transferring photos and sound files with Image Expert
your PhotoPC 800. Or see page A-2 for information on
◗
Getting images into TWAIN-compliant applications
ordering an AC adapter through EPSON Accessories.
◗
Getting images that you can import
The AC adapter should be available where you bought
◗
NOTE
When you connect the camera, make sure your system is
not exposed to sources of electromagnetic interference,
If your computer has a Type II PCMCIA card slot, you can transfer
such as stereo speakers or the base units of cordless
your pictures by copying them directly from your memory card.
telephones.
A
B
See page A-4 for instructions.
Getting Photos Into Your Computer 6-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Connecting to a Windows PC
NOTE
You can connect the camera to your USB-enabled
Although you can use a USB hub, it’s recommended that you
Windows 98 system with either the Windows serial cable or
the USB cable that came with the camera.
connect the camera directly to the computer’s USB port.
If you’re using the USB cable and you see the New Hardware
2
Open the connector cover on the side of the camera.
Then insert the connector on the other end of the USB
Found screen, follow the instructions on page 1-15.
cable into the camera’s interface port.
Using the USB Cable
Follow these steps to connect your camera using the USB
cable:
1
Plug the connector on the USB cable into the USB port
on your computer, or into a port on a USB hub.
3
6-2 Getting Photos Into Your Computer
Turn on the camera by turning the camera dial to
.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
Using the Windows Serial Cable
2
Locate the Windows serial cable that came with the camera,
then turn off the camera and your computer.
Line up the serial connector on the cable with one of the
serial ports on your computer, and insert the connector.
Then tighten the screws.
Follow these steps to connect the camera to your computer:
1
Locate a serial port on the back of your computer. You
may have two serial ports labeled COM1 and COM2, or
the ports may be labeled with icons. If you have two
serial ports available, use COM1 (port 1) to connect
6
your camera.
NOTE
If you have a 25-pin serial port, you can use a 9- to 25-pin
adapter.
3
Open the connector cover on the side of the camera.
Carefully insert the connector on the other end of the
cable into the camera’s interface port.
A
B
Getting Photos Into Your Computer 6-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Connecting to a Macintosh
.
You can connect the camera to your PowerPC with the
Macintosh serial cable that came with your camera. If you
have an iMac or PowerMac G3, you can use the USB cable.
See page 6-2 for instructions on connecting the camera with
a USB cable.
Follow these steps to use the Macintosh serial cable:
1
Turn off the camera and your Macintosh.
2
Locate the modem port
or printer port
on
the back of your Macintosh. You can use either port to
connect the camera.
4
Turn on the camera by turning the camera dial to
then turn on your computer system.
,
NOTE
If you’re sharing a serial port that you use for another device,
make sure AppleTalk™ is turned off. Your Macintosh may
NOTE
If you have problems connecting to the COM port you have
selected, check your computer’s COM port configuration and
try again.
6-4 Getting Photos Into Your Computer
not recognize the camera if AppleTalk is on. Also, if you have
problems connecting to the printer port, use the modem port
instead.
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
3
Open the connector cover on the side of the camera.
On a PowerPC or G3 Macintosh (or a Windows PC with a
Carefully insert the connector on the other end of the
cable into the camera’s interface port.
high-speed serial board), you may be able to transfer your
pictures at the rate of 230.4KB per second. If your camera
software doesn’t set this speed automatically, you can set it
manually. See page 10-6.
.
Transferring Photos and Sound Files
The PhotoPC 800 provides several different ways to transfer
your pictures from the camera’s memory card to your
computer. The simplest method is to use the Image Expert
6
software that came with your camera. This lets you view
small thumbnail images of your pictures, and then quickly
transfer them to an album (folder) on your hard disk drive.
If you haven’t installed your software, do it now. (See
Chapter 1.) Make sure the camera is connected to your
computer and the camera dial is turned to .
4
Turn on the camera by turning the camera dial to
then turn on your Macintosh system.
,
A
B
Getting Photos Into Your Computer 6-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
NOTE
2
Click View Pictures in the Camera. You see a
window displaying “filmstrips” of your images. (If you
see an error message instead, see page 6-9.)
Although these instructions apply to Windows 95 and 98, the
same steps can be used with a Macintosh or Windows NT 4.0
system.
click to start transferring your photos
1
Start Image Expert. Click Start, and then point to
Programs, Image Expert, Image Expert.
If you see the Image Expert Quick Tour screen, click
Close. (This screen does not appear on the Macintosh.)
You see a window like the following:
click to see
the pictures
in your
camera
6-6 Getting Photos Into Your Computer
3
Click the
button to transfer all the images to your
hard drive. To transfer a single image, select it, then
click the button.
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
You see a Select Album window like the following:
NOTE
◗
type here if you
want to rename
your album
To select more than one image, hold down the Ctrl key
while you click. To deselect, click another image.
◗
You must click the
button to transfer images. When you
view camera images on your computer, you have not yet
transferred them.
Windows
6
type here if you
want to rename
your album
Macintosh
A
B
Getting Photos Into Your Computer 6-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
4
Image Expert will automatically create an album (folder)
6
When you’re finished, close the filmstrip window.
for your pictures with the current date as its name. You
can type your own name for the album if you want, or
7
To erase all images from the camera’s memory card,
choose an existing album.
select Erase All Images from the Camera menu. To
erase a particular image, click the image to select it and
Click Open (or OK on a Macintosh) to begin
choose Delete from the Edit menu. You see a
transferring your pictures. You see a confirmation
message asking if you want to download selected images
confirmation message.
only.
5
Click Selected to download the selected images, or All
to download all images. A window like the following
appears to show you the progress of each image:
8
Click Yes to erase the image(s), or No to cancel.
You can double-click an image to open it in Image Expert.
You can display your images one by one, edit, print, and
copy them to diskettes, or place them in your documents and
presentations. See Chapters 7, 8, and 9 for more information
about working with images in Image Expert.
click if you want to stop
transferring images
6-8 Getting Photos Into Your Computer
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
What To Do if You See an Error Message
4
Click Retry. If you see the Connection Failed
message again, click Connection.
When you click the button to view images in the camera’s
memory card, you may see a message like the following:
You see the following dialog box:
6
Follow these tips to get your camera connected correctly:
1
Make sure the camera is turned on and has not shut off
automatically. If it has, turn the camera dial to Off, then
to .
2
Check the cable and make sure the connections are
secure. Make sure the pins inside the connector are not
bent.
3
5
Make sure your batteries have enough power, or your
AC adapter is connected.
Select another image source, if necessary. If you’re using
a PCMCIA adapter to access images from a PC card
slot, select PC Card.
6
Select another port if necessary. In most cases, it’s best to
leave the Port setting at Auto because Image Expert can
detect the camera connection automatically.
If you have a serial device connected to one port and an
internal modem on the other, you can try setting the
Port to COM3 or COM4.
Getting Photos Into Your Computer 6-9
A
B
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
If you have a USB port, try selecting USB, then
NOTE
remove the USB cable from your computer and
reconnect it.
7
you might choose Acquire or Select Source.
Select a slower speed. Image Expert automatically
chooses the fastest speed that works with your system,
but this may actually be too fast for the configuration of
your port. Try setting the speed to 57600. You may
need to experiment to choose the best speed.
8
The commands you choose from the File menu differ from
one host application to another. With other host applications,
When you are finished, click OK.
Getting Images Into TWAINCompliant Applications
If you use Adobe Photoshop or other TWAIN-compliant
applications, you can transfer your pictures directly into your
program from the camera. Follow these steps:
1
Start your application.
2
Choose Import, then Select TWAIN_32 Source if
you’re running Windows (or Import, then TWAIN
Select if you have a Macintosh) from the File menu.
6-10 Getting Photos Into Your Computer
3
For your TWAIN source, choose EPSON
PhotoPC 800 (Windows), or PhotoPC 800
(Macintosh).
For Windows, choose Import, then TWAIN_32 from
the File menu. For Macintosh, select Import, then
TWAIN_Acquire.
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
The EPSON Photo!3 screen appears, with thumbnail
You can also select a picture and do the following before
images of your photos. (If you see the message The
Camera Is Not Responding, see page 6-14.)
you transfer it:
click to transfer
your picture(s)
◗
Click View Photo to see a full-size image.
◗
Click one of the rotation buttons to turn the picture
90 degrees.
◗
Click Photo Info to see the capture time and date,
image resolution, and other information.
◗
Check PhotoEnhance to automatically improve
the picture during transfer. (You can select and
6
enhance all the pictures at once. However, using
this feature will make the transfer take significantly
longer. This feature is not recommended unless
you’re using the AC adapter.)
click if you
need help
4
Select the picture you want and click Get Photos to
transfer the picture. Or click Select All and then Get
Photos to transfer all the pictures.
5
After transferring, click Erase Photos if you want to
remove the picture(s) from your camera.
6
If necessary, click Close to exit the EPSON Photo!3
screen and return to your application. You see the
picture or pictures in the work area.
Getting Photos Into Your Computer 6-11
A
B
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
Getting Images That You Can Import
You see a screen like the one below. (If you see a Setup
Most methods of transferring images from the camera save
screen that says The Camera Is Not Responding, see
page 6-14.)
your pictures as JPEG files. If your word processor or other
application doesn’t support the JPEG format, you have to
convert the files one by one. Or you can use the export
click to transfer and
convert picture(s)
feature of EPSON Photo!3 to automatically convert the files
as you transfer them.
Follow these steps to export and convert your pictures with
EPSON Photo!3:
1
Start your EPSON Photo!3 software. Under
Windows 95 or 98, click Start, and then point to
Programs, EPSON Photo!3 Ver.1, EPSON
Photo!3 Ver.1.
2
Click the picture you want, or click Select All.
You can also view, rotate, or enhance the picture(s) or
see picture information before you export, as described
on page 6-11.
6-12 Getting Photos Into Your Computer
Altair.book Page 13 Thursday, July 1, 1999 3:33 PM
3
Click the Export Photos button. The Save As dialog
5
box appears:
Select the file type from the pull-down menu. You can
choose any of the following formats:
click if you want to
choose a different folder
click if you want to
create a new folder
6
◗
PICT (Macintosh only)
◗
JPEG
◗
Bitmap (BMP)
◗
PCX
Click Save. Your pictures are transferred one by one.
6
NOTE
You cannot open exported photos in EPSON Photo!3. Use
Image Expert to view and edit the exported images.
type a name
for your
photo(s)
4
click to choose
the file type
click to transfer
and “export”
photos
Type a file name. If you’re exporting more than
one image, the software will add numbers to identify
7
Click Erase Photos if you want to remove the pictures
from your camera.
A
each one.
B
Getting Photos Into Your Computer 6-13
Altair.book Page 14 Thursday, July 1, 1999 3:33 PM
Here are some additional things you can do with
EPSON Photo!3:
◗
Select the Folder tab and click Browse to locate
and display pictures you have downloaded. You can
then select a picture and click Upload to transfer a
picture from your computer to the camera or an
optional memory card. See Chapter 11 for more
information.
◗
Select the Controls tab to change camera settings
or view a live preview and take pictures from your
computer. See Chapter 10 for more information.
◗
Set the camera’s date and time from the Setup tab,
or change your computer connection settings. See
Chapter 10 for more information.
8
Click Close to exit EPSON Photo!3.
You can now insert your exported pictures in documents and
other projects. For instructions, see page 7-2.
6-14 Getting Photos Into Your Computer
What To Do If the Camera Is Not
Responding
When you try to acquire pictures from the camera or start
the EPSON Photo!3 application, you may see a screen like
the following:
Altair.book Page 15 Thursday, July 1, 1999 3:33 PM
Follow these steps to fix your camera connection:
1
5
chooses the fastest speed that works with your system.
This may actually be too fast for the configuration of
Check the cable and make sure the connections are
secure. Make sure the pins inside the connector are not
bent.
2
Make sure your batteries have enough power, or your
AC adapter is connected.
3
Click Test Connection. If you see the same screen,
Select a slower speed. EPSON Photo!3 automatically
your port. Try setting the speed to 57600. You may
need to experiment to choose the best speed.
6
Click Test Connection again. If you still don’t see
your pictures, see Chapter 13 for more troubleshooting
tips.
6
continue with step 5.
4
Select another port if necessary. In most cases, it’s best to
leave the Port setting at Auto because EPSON Photo!3
can detect the camera connection automatically.
If you have a serial device connected to one port and an
internal modem on the other, you can try COM3 or
COM4.
A
If you’re using a USB port, try selecting USB, then
remove the USB cable from your computer and
B
reconnect it.
Getting Photos Into Your Computer 6-15
Altair.book Page 16 Thursday, July 1, 1999 3:33 PM
6-16 Getting Photos Into Your Computer
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
.
7
Getting Your Photos Into Documents
P
Gardening Monthly
November 1998
Cactus Fever
- Focus on Echinocatus
Large, round or cylindrical cacti with deep
accordianlike ribbing and prominent spines
comprise this group of Mexican and Southwestern
U.S. natives. They vary in size and shape, but all
are easy to grow and can reach 10 ft. tall and wide.
Spring and summer flowers bloom in pink or
yellow in a circle at the plant’s crown. Don’t plant
where children are present.
With Windows, you can use the Camio™ Viewer to drag a
picture directly from the camera and drop it into your
Sunflowers are big-leafed, sturdy plants that need
full sun and moist soils. Seeds attract birds.
Perennial species grow rapidly, forming sizable
clumps that can become invasive. Plant in large
gardens or parks. Start by division or seed. All
bloom in late summer and fall.
New Next Month
Grilled Cactus Pads
* 1 pound cactus leaves
Orchid Mania
Landscaping
* Olive Oil
This is an interesting treat for a cookout. Scrub cactus leaves
well with a vegetable scrubber to remove any spines that may
be on them. With the end of a potato peeler cut around the
spiney nodules and remove them. Make sure that all are
removed. Grill the leaves over charcoal or wood fire for 10
to 12 minutes on each side. Thicker leaves may take slightly
longer to grill. Brush leaves with oil occasionally while
grilling. Serve hot.
projects. You can drag and drop a picture from an Image
Expert album into a document or presentation. You can also
import an image into your application, or copy and paste it.
Sunflowers
Recipe of the Month
hotoPC 800 provides several methods for getting
your pictures into presentations, letters, and other
Bulbs
Page 2
Page 3
project. This chapter describes the following:
◗
Importing images into documents
◗
Getting images with copy and paste
◗
Using drag and drop from an album
◗
Getting images with the Camio Viewer
Book Reviews Page 4
Seeds
Page 5
Supplies
Page 6
7
A
B
Th is p rint sam ple was created usin g actual 10 24x7 68 pixel images tak en with th e EPSON PhotoPC 600 XGA color digital cam era. It was
printed with the EPSON Stylus Color 6 00 prin ter at 1440 dp i on EPSON Pho to Quality Glossy Paper.
Getting Your Photos Into Documents 7-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Although most of the instructions and illustrations in this
3
Select the point where you want to place your picture.
chapter apply to Windows 95 and 98, you can follow the
same steps on a Macintosh or Windows NT 4.0.
4
Select Picture from the Insert menu. (In some
applications you may need to select a different
command, such as Import Picture, which is usually in
Importing Images Into Documents
the File menu.)
Once your pictures are transferred and saved on your hard
drive, you can import them into your applications. You may
need to convert your images if you didn’t export them from
An Insert Picture dialog box appears (your dialog box
may look different, depending on your application):
the camera (as explained in Chapter 6) and your application
can’t import JPEG files. Or you can use the Save As feature
of Image Expert to convert image files.
NOTE
Your picture may display poor image quality after you import it.
However, in most cases it will print correctly.
Follow these steps to import a PhotoPC 800 picture into
your document:
1
Start your application.
2
Open the document where you want to use the picture.
7-2 Getting Your Photos Into Documents
5
Locate and select the image you want to insert. In some
applications you can see a preview of your picture.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
6
Click OK (or Insert, Import, or whatever command
your application uses) to insert your picture. The picture
appears in your document.
NOTE
In some applications, you can add a frame around the picture if
you want to move it around on the page or resize it. In other
applications, you create a frame first and then place the picture in
it. For instructions, see your application’s online help or
documentation.
Getting Images With Copy and Paste
You can use this method to place a picture in just about any
type of document or project. You should already have
transferred your picture from the camera to your hard disk.
Follow these steps:
1
Start Image Expert. (See page 6-5.)
2
Click View Pictures from an Existing Album. Or,
from the Image Expert screen, click the Open Album
button
or select Open Album from the File menu.
7
A
B
Getting Your Photos Into Documents 7-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
You see a dialog box like the following:
6
Open the document where you want to use the picture.
7
Choose Paste (or Paste Special) from your
application’s Edit menu. A copy of the picture appears
in your document.
Using Drag and Drop From an Album
(Windows Only)
Once you have transferred your pictures into albums, you
can easily drag and drop them into documents or other
projects.
3
Locate the album you want and double-click it to open
it. When a filmstrip of album images appears in the
NOTE
Dragging and dropping an image into a document works only with
OLE-2.0-compliant applications, such as Microsoft Word,
Image Expert window, click the picture you want to
copy.
PowerPoint, WordPerfect, or Lotus SmartSuite. Depending
Click the Copy button or select Copy from the Image
import them.
on how well your application supports OLE 2.0, your images may
not look as good when you drag and drop them as when you
4
Expert Edit menu.
5
Start your word processor or other application.
7-4 Getting Your Photos Into Documents
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Follow these steps:
You should have both the Image Expert album and the
1
Start Image Expert as described on page 6-5.
2
Click View Pictures from an Existing Album, or
click the Open Album button
screen.
document displayed on your screen, as shown:
from the Image Expert
3
Locate the album you want and double-click it to
open it.
4
Start your word processor or other application.
5
Open the document where you want to use the picture.
7
6
Click the image you want.
7
While holding down the mouse button, drag the image
to the location where you want it in your document.
8
Release the mouse button. The picture appears in your
project or document.
Getting Your Photos Into Documents 7-5
A
B
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
You see the Camio Viewer Startup Options dialog box:
If you want to edit or modify the picture, just double-click it
on the Image Expert window to bring up the Image Expert
menus and toolbar.
Getting Images With the Camio
Viewer (Windows)
The Camio Viewer is a quick and easy way to get pictures
from the camera. You can transfer all images to your
computer, or just display the pictures in the camera. Then
you can drag a picture directly into a presentation or
document.
2
Choose one of the following options:
◗
NOTE
Dragging and dropping an image with the Camio Viewer works
only with OLE-2.0-compliant applications running under
Windows 95, Windows 98, or Windows NT.
First you need to connect the camera to your computer as
described in Chapter 6. Then follow these steps:
1
Double-click the camera icon
your Windows taskbar.
on the right end of
7-6 Getting Your Photos Into Documents
View images in the Camera
Displays a filmstrip of your pictures. You can then
select an image to drag and drop into a document or
presentation. (The image will be embedded in your
document, and will not be available as a separate
file.)
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
◗
Copy all images from the Camera to
the Computer
Transfers your pictures to an album (folder) on your
hard drive. You can then select an image to drag and
drop.
◗
Copy all images and delete them from
Dragging and Dropping a Picture Into
a Document
Follow these steps if you chose View images in the
Camera:
1
Click OK. Your pictures appear in a strip of thumbnail
images:
the Camera
Transfers your pictures to an album (folder) on your
hard drive and deletes them from the camera. You
can then select an image to drag and drop.
3
7
Continue with the steps in one of the following sections,
depending on the option you chose in step 2.
A
2
Open the application and document where you want to
use the picture.
Getting Your Photos Into Documents 7-7
B
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
3
Click the picture you want to use. Without releasing the
Transferring Images Before Placing Them
mouse button, drag the picture to your document.
When your pointer is over the location where you want
Follow these steps if you chose Copy all images:
the picture to appear, release the mouse button. The
picture is downloaded from the camera, and it appears
1
Click OK to copy your pictures to an album named with
in your document.
the current date. Or, type a new name for the album and
click OK. Your pictures are transferred one by one. They
If you want to edit or modify the picture, just double-
appear in a strip of thumbnail images, as shown on the
previous page.
click it in the Camio Viewer filmstrip to bring up the
Image Expert menus and toolbar. For more information
about the Camio Viewer, choose Quick Tour from the
Image Expert Help menu.
NOTE
When you drag and drop with the Camio Viewer, your picture is
not saved as a separate image file on your hard drive. You have to
transfer your image first if you want it to be available as a
separate image file.
7-8 Getting Your Photos Into Documents
2
Follow steps 2 and 3 in the previous section to drag and
drop a picture into a document or other project.
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
6.
8
8
Working With Photos and Albums
Y
ou can use Image Expert albums to organize and
display your pictures. You can print using dozens of
predefined layouts. On Windows systems, you can also
record sounds for each image, copy an album to diskette, use
your images as wallpaper, and more. This chapter covers the
following:
◗
Using albums
◗
Printing an image or album
◗
Adding sound to an image
◗
Displaying albums as slide shows
◗
Using an album as a screen saver
◗
Setting an image as wallpaper
◗
Copying to diskette or Zip™ disk
◗
Sending pictures and sound by e-mail
Working With Photos and Albums 8-1
8
A
B
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Using Image Expert Albums
If you want to create a new album, click the
Image Expert albums provide a convenient way to access and
New Album button
view your pictures. Here are some of the things you can do
the File menu.
or select New Album from
with albums:
◗
Organize pictures in albums
◗
Rename a picture
◗
View picture information
Organizing Pictures in Albums
existing
album
new
album
Although Image Expert initially sorts your pictures by date,
you can easily drag and drop images between albums to
organize them by subject matter or in any way you want.
Follow these steps to copy or move images from one album
to another:
1
2
Open the album you want to copy the images to and the
album where the pictures are located.
Select the image or images you want to move or copy.
Hold down the Ctrl (Option on Macintosh) or Shift
key to select multiple images.
3
To copy or move images, click inside one of the selected
images and hold down the mouse button.
4
8-2 Working With Photos and Albums
Drag the image(s) to the other album.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
5
When the second album is highlighted, let go of the
2
mouse button.
The images are copied to the album. You can sort the
pictures and save or rename the new album.
Renaming a Picture
You can easily rename a picture displayed in an Image Expert
album. Follow these steps:
1
Click the picture to select it, then click the name that
of the name area. The new name appears above the
picture and is saved.
Viewing Picture Information
You can display information about any image file and the
camera settings that were used to capture it. Follow these
steps:
1
Click the picture to select it, or double-click it to
open it.
appears above the picture. The name is highlighted.
2
click here to change a
picture’s name
Type in the new name and press Enter or click outside
Click the Properties button
or select Properties
from the Image menu. You see information like the
following:
8
A
B
Working With Photos and Albums 8-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
3
Click the Camera Settings tab to display information
like the following:
2
Click the Print Layout button
or choose Print
Layout from the File menu. The Print Layout window
appears:
click to display next
or previous page
4
click to display list of
sizes and layouts
click to adjust
margins
Click another image to view its information, or close the
Properties box.
Printing an Image or Album
Image Expert offers many choices for printing an individual
picture or album with titles, labels, or any text you want to
add. You can print an image at full size (one per page) or
choose the number of prints per sheet of paper. You can also
specify a size, or print combinations with standard sizes for
framing.
Follow these steps to print:
1
Open the image or album you want to print.
8-4 Working With Photos and Albums
The image in the center of the screen shows you a
preview of your printout.
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
3
Follow the instructions in the sections below to adjust
3
printer settings, choose your layout style, select album
images, add text, and adjust the printed area for your
drop-down list of sizes and layout choices:
images.
4
when you’re
printing an
album, you
can choose
from two
types of
contact
sheets
When you’re finished designing your layout, click the
Print button
Click the down arrow next to the size box to display the
to print your picture(s).
Choosing the Layout Style
You can choose portrait or landscape orientation and select
from a variety of layouts.
Follow these steps:
1
up for a standard letter-size sheet.
2
8
Click the Print Setup button
if you need to select
your printer or paper size. Otherwise, all layouts are set
Click the Portrait button
or Landscape button
to change the orientation of the page.
4
Choose the size and number of images you want per
page. If you need a custom size, choose Custom Size.
You can then enter exact dimensions for your picture, or
size it interactively in the layout window.
A
B
Working With Photos and Albums 8-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
5
When the preview shows the layout you want, you can
2
or follow the instructions in
click the Print button
the next sections to add text or make other adjustments
and then type the text you want to use in the Left,
Center, or Right boxes (depending on how you want it
to your printout.
to display). You can type different text for each box.
3
Adding Text
printed with your pictures, follow these steps:
Click the Edit Text button
4
. The Change Print Text
5
8-6 Working With Photos and Albums
Click Insert Special Text to choose one of the
following for your header, footer, or labels (only some of
the choices are available for each):
dialog box appears:
Type here if you want your text centered
under the picture or on the page. Otherwise,
type it in the Left or Right box.
Click Change Font to set the font size, style, color, and
so on for your header, footer, or labels.
If you want to have image labels or page headers or footers
1
Select Page Header, Page Footer, or Image Label,
When you’re finished designing your text, click OK.
The text is previewed on your layout in the center of the
screen.
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
2
Choosing Album Images
where you want it to appear in the layout.
If you’re printing an album, Image Expert uses as many
pages as necessary to print the entire album. If you don’t
want to print all the images, you can choose the ones you
want and position them in your layout. Follow these steps:
1
Click the Pick Images button . Your album appears
in a “filmstrip” on the right side of your screen.
Choose the images you want to print, and drag each one
You may notice that some images are cropped. If you want to
adjust the cropping, or zoom an image in or out, follow the
instructions in the next section.
Adjusting the Printed Area
You can zoom in on an image, and then move it around to
display just the portion you want. Follow these steps to
adjust the printed area:
1
Double-click the image you want to adjust.
8
A
B
page layout
album filmstrip
Working With Photos and Albums 8-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
The other images fade out, and the sizing tools on the
4
Click the Reset Size button
to return to the default
size and layout.
left side of the screen become active.
5
sizing
tools
When the preview shows the layout you want, you can
click the Print button
to produce your printout.
Adding Sound to an Image
If your Windows system includes a microphone and a 16-bit
sound card with speakers, you can add voice or musical
annotations to your pictures. Follow these steps to add sound
to a picture in Image Expert:
2
Click the Zoom In tool
and then click on an image
to enlarge and crop it.
You can also click the Zoom Out tool
your image and display more of it.
3
to reduce
Click the Move tool
and then click on an image to
move it and choose the portion you want to display.
8-8 Working With Photos and Albums
1
Select the image you want to add sound to.
2
Click the Record button
on the left side of your
screen or select Record Audio from the Annotation
menu to open the Record dialog box:
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
3
4
Select the option you want:
Playing Back Sounds
◗
To add sound to an image, choose Record New.
When you open an image that has audio attached to it
◗
To add additional sound to an existing audio clip,
choose Record Additional.
◗
To end your recording, choose Stop.
◗
To listen to your new recording, choose Play New.
◗
To listen to your original recording, choose Play
Original.
If you like your new recording, click OK. Otherwise,
click Undo to delete the new recording, then repeat
step 3 to make a new recording.
(indicated by a music note), the audio clip automatically
plays.
indicates audio
message
You can also select an image and use the buttons on the left
side of the Image Expert window to listen to its audio clip:
play or restart
8
pause
stop
record
edit
A
B
Working With Photos and Albums 8-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
◗
Editing Sounds
menu to add the sound clip to the new image.
You can use Image Expert to modify your recorded sounds
by cutting or copying and pasting from one clip to another.
Follow these steps:
1
Select an image that has an audio clip.
Select another image and click Paste from the Edit
NOTE
To adjust recording or playback volume or modify other features,
select Audio Properties from the Annotation menu. You can also
click the sound icon on your Windows taskbar. Use the volume
2
Click the Edit Audio button , or choose Edit Audio
from the Annotation menu. The sound wave window
opens:
control on your speakers to quickly adjust playback volume.
Deleting Sounds
To delete an audio clip, follow these steps:
1
Select the image with the sound you want to delete.
2
Select Delete from the Edit menu, or press the Delete
key on your keyboard. The following message appears:
3
Click and drag to select a section of the audio clip, or the
entire clip. You can perform the following operations:
◗
Click the Play button to hear the section you
selected.
◗
Select Cut from the Edit menu to remove it.
◗
Click Copy from the Edit menu to copy it.
8-10 Working With Photos and Albums
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
3
Check the Only delete the audio box, then click Yes.
4
To change the look of your slide show, click the Options
button
. The Slide Show Options dialog box appears.
Displaying Albums as Slide Shows
When you display an Image Expert album as a slide show in
Windows, you can have it play automatically with various
transition effects between images. Follow these steps:
1
Open your album.
2
Click the Slide Show button
or select
Slide Show from the View menu.
The first image appears on your screen with the slide
show controls:
5
close
Set any of the following options and click OK:
◗
options
stop
play
play audio
Click the Play button
to see the slide show.
To stretch your pictures across the whole screen,
click Fit to Screen.
◗
3
8
To change the display period for each picture,
change the number in the Seconds Between
Pictures box.
Working With Photos and Albums 8-11
A
B
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
◗
◗
To play the slide show only once, click
Windows will play a slide show of your album whenever
Continuous Repeat to deselect it.
your system is idle.
To hide the titles of your pictures, click Show
NOTE
Titles to deselect it.
The screen saver slide show doesn’t include controls. If you want
◗
To turn off the fades and dissolves that play
between pictures, click Show Transition Effects
to deselect it.
◗
the screen saver settings in your Control Panel. See your
Windows documentation or Help system for more information.
To turn off audio clips attached to your images,
click Play Sounds to deselect it.
6
to change the way your pictures are displayed, you have to use
Click the Close button
to stop the slide show.
Setting an Image as Wallpaper
If you’re using Windows, you can use one of your own
pictures as your desktop background. Follow these steps:
Using an Album as a Screen Saver
1
Open or select your image in an Image Expert album.
If you’re using Windows, it’s easy to make your own screen
saver with your favorite pictures. Follow these steps:
2
Choose Set As Wallpaper from the File menu.
1
Open the Image Expert album you want to use.
2
Choose Set Screen Saver from the File menu. Image
Expert asks you to confirm your choice.
3
Click Yes.
8-12 Working With Photos and Albums
Altair.book Page 13 Thursday, July 1, 1999 3:33 PM
The following dialog box appears.
Copying to Diskette or Zip Disk
If you’re using Windows, you can copy Image Expert albums
or individual images to diskettes or Zip disks. You can also
include a player, so your friends and business associates can
view your pictures on their computers. This makes your
images and albums completely portable.
Follow these steps:
click to remove
existing wallpaper
1
Insert a diskette into your diskette drive or a Zip disk
into your Zip drive.
3
Choose Center to place your picture in the middle of
the screen or Tile to fill the screen with copies of your
2
picture.
4
If you want the image to be stretched across the whole
screen, click Resize to fit screen.
5
Click Yes. (If you change your mind, click Remove
Open the Image Expert album you want to copy.
If you don’t want to include all of your images, select the
images you want to add. To select more than one image,
8
hold down the Ctrl or Shift key.
3
Select Save To Floppy from the File menu.
Wallpaper.)
A
B
You can minimize Image Expert to see your new
wallpaper.
Working With Photos and Albums 8-13
Altair.book Page 14 Thursday, July 1, 1999 3:33 PM
You see the following dialog box:
Viewing the Pictures on Diskette or Zip Disk
To run the slide show, double-click the player icon or
player.exe file. The pictures appear on your screen with the
slide show controls, as shown below:
close
stop
4
5
6
play
Make sure your diskette drive or Zip drive letter appears
in the Copy images to box.
To include a slide show player to view the pictures,
See page 8-11 for instructions on setting slide show options.
make sure Include Slide Show Player is checked.
Sending Pictures and Sound by
E-mail
If you want to copy the whole album, make sure there is
If you’re using Windows and your e-mail application
no check mark next to Selected Images Only.
complies with the MAPI (messaging application
NOTE
programming interface) standard, you can send a picture
directly from Image Expert. For example, you can use Inbox
Make sure your diskette (or other storage device) is not
write-protected before you try to copy.
7
options
play audio
Click OK to copy your files.
8-14 Working With Photos and Albums
or Microsoft Exchange. You need to set up Microsoft
Exchange to work with your Internet service.
Altair.book Page 15 Thursday, July 1, 1999 3:33 PM
NOTE
If you can’t e-mail pictures directly from Image Expert, you can
click to configure
your Internet
service for
Microsoft
Exchange
always send an e-mail message as you do normally and attach
one or more image and sound files.
Before you start, make sure your modem and Internet service
are working correctly and your e-mail application is
4
configured. Then follow these steps:
1
Open an album in Image Expert.
2
Select or open the image(s) you want to send. Some
Click New if your Internet service has not been set up
to work with Microsoft Exchange. For more
information about setting up Microsoft Exchange, see
your Windows documentation or help system.
e-mail systems may limit the number of images you can
send in a single message.
5
Click OK. Your e-mail application opens, and the
image(s) you selected appear as attachments.
NOTE
6
Type the e-mail address where you’re sending the
If no images are selected, all images in the album will
picture(s). You can also type in a subject heading and
message if you want.
be sent.
3
Choose the profile you want to use.
Choose Send from the File menu. You see the Choose
Profile dialog box.
7
When your e-mail is ready, click whatever button your
application uses to send. The picture(s) are mailed.
Working With Photos and Albums 8-15
8
A
B
Altair.book Page 16 Thursday, July 1, 1999 3:33 PM
Your e-mail application closes, and Image Expert
becomes active again.
8-16 Working With Photos and Albums
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
.
35
9
Editing Images
Y
ou can edit your images to enhance their appearance,
crop, rotate, and resize them, or create special effects.
This chapter describes the following Image Expert features:
◗
Viewing and selecting images
◗
Applying Quick Fix
◗
Correcting an image
◗
Cropping an image
◗
Resizing an image
◗
Rotating and flipping an image
◗
Applying special effects
◗
Changing the number of colors
9
A
B
Editing Images 9-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Viewing and Selecting Images
◗
enlarge your view. Right click or hold down the control
key and click to zoom out.
When your image is displayed in an album, you can rotate it
or do a quick fix. However, to use any other editing features,
you need to open the image by double-clicking it or selecting
Open Image from the File menu.
Click Zoom, and then click anywhere on your image to
◗
Use one of the three selection tools (Select Rectangle,
Select Ellipse, Select Freehand) to isolate a part of
your image before you edit it. Click the tool, then click
and drag on your image to select the portion you want to
Before you edit your image, you may want to use the Zoom
and selection tools on the left side of your screen.
work on.
◗
Click Select All to select your entire image or all the
images in an album.
Zoom
Select Rectangle
◗
Select Ellipse
NOTE
Click Select None to deselect your image or images.
For more information about any of the editing tools described in
Select Freehand
Select All
Select None
9-2 Editing Images
this chapter, use the Help menu.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
Applying Quick Fix
Correcting an Image
The easiest way to improve your image is to have Image
To fine-tune an image, follow these steps:
Expert automatically “correct” it with the Quick Fix
command. Follow these steps:
1
2
Double-click your image to open it in the Image Expert
window.
Click the Quick Fix tool
1
Double-click your image to open it.
2
Click the Corrections tool
or choose Corrections
from the Image menu. You see a window like the
following:
or select Quick Fix from
the Image menu.
If you don’t like the results, simply select Undo Quick Fix
from the Edit menu.
NOTE
If you Quick Fix an image displayed in an album (without opening
9
it in the Image Expert window), you can’t undo it.
A
click and drag to adjust the
division between the original
and edited preview
Editing Images 9-3
B
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
3
Click the tabs at the top of the screen to make these
Each dialog box tab includes sliders for quickly and
kinds of corrections:
easily correcting your image. Simply move the slide
indicator left or right to make your edit.
◗
◗
Contrast and Brightness
For adjusting the amount of light in your image and
The preview window shows your image with the
the difference between light and dark areas.
original view on the left and the corrected image on the
Color
right. If you want to adjust the division between the
original and edited image, click and drag the triangle
For correcting color casts and adjusting the balance
of cyan (blue), magenta (red), and yellow; and red,
below the image. You can also zoom in on your image
to see more detail.
green, and blue in your picture.
◗
Hue/Saturation
For adjusting colors around the “color wheel,” the
strength or purity of color, and the brightness of
4
Do one of the following:
◗
tab. Your edited image becomes your new original
your image.
◗
◗
and the slide indicators move to the center of the
range.
Sharpness
For emphasizing or de-emphasizing edges and
details.
Equalization
For increasing and brightening detail in dark areas
of your image.
9-4 Editing Images
Click Apply to make your changes on the current
◗
Click OK to save the changes you made on all the
Corrections tabs and return to the main screen.
◗
Click Cancel to cancel the changes on the current
tab and return to the main screen.
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Cropping an Image
4
to crop, simply click anywhere outside the selected area
of the image and repeat step 3.
If you want to save only part of your image, use the crop
function to cut out the rest of the image. Follow these steps:
1
Double-click your image to open it in the Image Expert
If you change your mind about which part of the image
5
Click the Crop tool
or choose Crop from the Image
menu. The part of the image that was outside the dashed
window.
2
Click one of the selection tools.
3
Click and drag the mouse over the area you want to save.
A dashed border indicates the area you selected.
line disappears.
Resizing an Image
You can resize your image by changing the number of pixels.
This lets you maintain the image’s original resolution or
pixels per inch.
1
Double-click your image to open it in the Image Expert
window.
9
A
B
selected area
Editing Images 9-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
2
Choose Resize from the Image menu. You see a dialog
Rotating an Image
box like the following:
You can click the Rotate tool
to quickly rotate a picture
to the right. For more options, open the image you want to
change and select Rotate from the Image menu.
NOTE
this box
changes size
to reflect the
numbers you
enter
If you rotate an image displayed in an album (without opening it in
the Image Expert window), you can’t undo it.
You can choose one of the following:
3
◗
Left (90 degrees counterclockwise)
Type a new number for the width or height.
◗
Right (90 degrees clockwise)
To maintain your image’s proportions, both numbers
change together. If you want to distort your image, click
◗
Exact (specify the degree of rotation)
◗
Free (interactive rotation, as described below)
Preserve Aspect Ratio to deselect it.
9-6 Editing Images
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
If you want to experiment with rotation, choose Free and
3
follow these steps:
1
Click on your image and hold down the mouse. Your
pointer turns into the rotation tool.
A rectangular outline of your image and an arrow
appear, as shown:
Release the mouse when your picture is at the angle you
want.
Flipping an Image
You can reverse your image by following these steps:
1
Double-click your image to open it in the Image Expert
window.
2
Do one of the following:
◗
Select Flip Horizontal from the Image menu.
(This is useful for printing T-shirt transfers.)
◗
Select Flip Vertical to turn your image upside
down.
9
A
B
2
Move the pointer to rotate your image.
Editing Images 9-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
Applying Special Effects
2
Click the tabs at the top of the screen to add these
To transform or distort your images in interesting ways,
effects:
follow these steps:
◗
1
Ripples
Open your image in the Image Expert window, then
For an underwater effect. You can create whirlpool
choose Effects from the Image menu. You see a dialog
box like the following:
effects or just a slight distortion.
◗
Glass blocks
You can change the number and size of the blocks.
◗
Edges
To sharpen edges. You can also blend the image
into a light or dark background.
◗
Fisheye
To distort the center of the image, as if looking
through a glass ball.
◗
Invert
To create a negative of your image, or to “solarize”
it.
9-8 Editing Images
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
Each dialog box tab includes sliders for applying the
Changing the Number of Colors
effect. Slide the indicator to the right to increase the
distortion. You can combine several filters for even more
To convert the color format of your image, open it and select
unusual effects.
from the following:
The preview window shows your image with the original
◗
view on the left and the distorted image on the right.
If you want to adjust the division between the original
and filtered image, click and drag the triangle below
the image. You can also zoom in on your image to see
Number of Colors from the Image menu. You can choose
The way your images are originally captured.
◗
software.
◗
Do one of the following:
◗
Click Apply to make your changes on the current
tab. Your distorted image becomes your new
original and the slide indicators move to the center
◗
◗
8 Bit (256 Colors)
For low-resolution display systems or certain types of
more detail.
3
24 Bit (Millions of Colors)
Grayscale (256 Shades of Gray)
For printing in black and white.
If you save your image as 8 Bit or Grayscale, you cannot
switch back to 24 Bit color.
of the range.
NOTE
Click OK to save the changes you made on all the
Unlike the other editing options, changing the number of colors
Effects tabs and return to the main workspace.
applies to the whole image. You can’t change the number of
colors for a selected area only.
9
A
B
Click Cancel to cancel the changes on the current
tab and return to the main workspace.
Editing Images 9-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
9-10 Editing Images
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
.
10
W
Operating the Camera From Your
Computer
hen the camera is connected to your computer,
you can take pictures with a live preview on your
computer screen to help you frame each shot. You can also
set the camera’s clock and adjust a number of other settings
from your computer.
Taking Pictures From Your Computer
With Image Expert
When you connect the camera and take pictures from your
computer, you see a live preview of each shot before you
capture it. You can control camera settings from your
This chapter covers the following:
computer, and even set the shutter speed.
◗
Taking pictures from your computer
NOTE
◗
Adjusting camera settings from your computer
If you have the optional AC adapter, you can save on batteries by
using it when you connect the camera to your computer. The AC
NOTE
adapter should be available where you bought your PhotoPC 800,
You can use either Image Expert or EPSON Photo!3 to take
or you can order it from EPSON Accessories. See page A-2 for
pictures from your computer, adjust camera settings, and transfer
more information.
10
A
images. PhotoPC 800 allows you to choose the application that
B
best meets your needs and preferences.
Operating the Camera From Your Computer 10-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
You see a dialog box like the following:
Follow these steps to take pictures from your computer:
1
Connect the camera to your computer as described in
Chapter 6.
2
click to
capture the
image you
see
Position the camera facing the subject. Using a tripod
will give you the most control when setting up your
shots. See page A-4 for instructions.
3
Turn on your computer, then turn the camera dial to
either
or
click to erase
images in the
camera
. Open the camera lens.
4
Start Image Expert as described on page 6-5.
5
If necessary, close the Quick Tour and the Image Expert
tip screen.
6
Click the Camera Controls button
Controls from the Camera menu.
or choose
7
Click Continuous Update to activate the live preview
feature. The image you see is updated every 8 to 10
seconds, depending on your connection speed. You may
need to move the camera or your subject until you see
the image you want to capture.
The colors in your live preview image may appear pale
and washed-out. This will not affect the colors in your
actual photograph.
10-2 Operating the Camera From Your Computer
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
You can click the Flash and Resolution buttons on the
Using the Self Timer
screen to adjust these settings just as you would by using
the buttons on the camera. For more information about
You can use this feature to have your computer take a picture
the flash and resolution (image quality) settings, see
Chapter 3.
automatically, after a delay period that you can set. This
allows you to take self-portraits and other specialized shots.
Follow these steps:
NOTE
1
Click Self Timer. You see the following dialog box:
2
Enter a number for the delay period you want to use.
When the camera is connected to your computer, you can’t
use any of the control buttons or the shutter button on the
camera. You can operate these features only through your
computer.
8
When your shot is ready, click Take Picture. The
image is captured and processed.
9
Click Close when you’re finished taking pictures from
your computer.
NOTE
The live preview feature quickly drains your batteries. Make sure
you turn it off as soon as you’re finished, or use the optional AC
adapter.
You can set up to a 120-second delay.
3
Click Start/Stop to start the countdown and take the
picture. The red timer light on the camera remains on
for the delay period you entered. Then the light flashes
rapidly for 2 seconds and the shutter is released.
The camera beeps and processes your picture.
Operating the Camera From Your Computer 10-3
10
A
B
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Taking Pictures With EPSON Photo!3
4
Click the Controls tab. You see a dialog box like the
following:
You can use your EPSON Photo!3 application to take
pictures from your computer, in the same way as Image
Expert.
1
Connect the camera to your computer as described in
Chapter 6, and then position the camera facing the
subject.
NOTE
Using a tripod will give you more control when setting up
your shots. (See page A-4 for instructions on using a tripod.)
2
Turn on both your camera and your computer, then
open the camera lens. Make sure the camera dial is set
to
or .
3
5
Click Start to display the live preview.
Start EPSON Photo!3. (Click Start, and then point to
The colors in your live preview image may appear pale
and washed-out. This will not affect the colors in your
Programs, EPSON Photo!3 Ver.1, EPSON
actual photograph.
Photo!3 Ver 1.)
10-4 Operating the Camera From Your Computer
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
You can use the Mode, Flash, Self Timer, and
Macro controls on the screen to adjust these settings
just as you would by using the buttons or LCD menus
on the camera. (For information about using the
camera’s buttons, see Chapter 3. For information about
using the LCD menus, see Chapter 4.)
6
When your shot is ready, click Take a Picture . The
image is captured and processed.
7
Click Close when you’re finished taking pictures from
your computer.
The Auto-Stop Timer shuts off the live preview after one
minute to save battery power. You can set the timer from
30 seconds to 5 minutes.
Adjusting Camera Settings From
Your Computer
You can use either Image Expert or EPSON Photo!3 to
change the following camera settings:
◗
Time
◗
Date
◗
Power down time (Image Expert only)
◗
Camera ID
◗
Connection Port
◗
Connection Speed
Changing Settings With Image Expert
You can change settings in Image Expert while you’re
viewing pictures in the camera. Follow these steps:
1
Connect the camera to your computer as described in
Chapter 6.
2
Turn the camera dial to
, then turn on your computer
system.
Operating the Camera From Your Computer 10-5
10
A
B
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
3
Start Image Expert, then select Properties from the
4
Camera menu. The Camera Properties menu appears:
Click OK to save your settings and exit the Camera
Properties dialog box.
5
If you want to adjust your port settings, select
Connection from the Camera menu. You see the
Connection dialog box:
◗
Enter a new Description of the camera to change
the default. This might be useful if you have more
than one camera and you want to record its
description in your picture data.
◗
Type in the Camera Time box to change the time
and date. Or, click Set Camera to Computer
Time to automatically synchronize your camera to
your computer.
10-6 Operating the Camera From Your Computer
◗
If necessary, select a new source. The standard
selection is Serial/USB. If you’re using a PCMCIA
adapter to access a PC card slot, select PC Card in
the Connect Via drop-down list. (FlashPath is
not implemented on the PhotoPC 800.)
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
◗
Select another port if you want to change your
Changing Settings With EPSON Photo!3
connection. In most cases, it’s best to leave the Port
setting at Auto because Image Expert can detect the
You can also change settings in EPSON Photo!3 while you’re
camera connection automatically.
◗
Select a different communication speed. Image
Expert automatically chooses the fastest speed that
works with your system. This may actually be too
fast for the configuration of your port. You may
need to experiment to choose the best speed. (See
your Windows documentation or help system to
change the port speed for your computer.)
6
viewing pictures in the camera. Follow these steps:
1
Connect the camera to your computer as described in
Chapter 6.
2
Turn the camera dial to
, then turn on your computer
system.
3
Start EPSON Photo!3, then click the Setup tab to
display the following dialog box:
Click OK to save your settings and exit the Connection
dialog box.
10
A
B
Operating the Camera From Your Computer 10-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
4
Change any of the following Computer Connection
You see a dialog box like the following:
settings:
◗
Select another port if you want to change your
connection. In most cases, it’s best to leave the Port
setting at Auto because EPSON Photo!3 can detect
the camera connection automatically.
◗
Select a different communication speed. EPSON
Photo!3 automatically chooses the fastest speed that
Enter new values for the settings, or click Copy from
Computer to have your camera automatically
works with your system. This may actually be too
synchronized to your computer. Click OK to return to
fast for the configuration of your port. You may
need to experiment to choose the best speed.
5
Click Test Connection to make sure your new settings
work with your system.
6
Click the Set Time button to change the camera’s time
and date settings.
10-8 Operating the Camera From Your Computer
the Setup dialog box.
7
Enter a new Camera ID if you want to change the
default. This might be useful if you have more than one
camera and you want to be able to have its ID recorded
in your picture data.
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
.
11
Y
Using Your Camera for Presentations
ou can connect your camera to a multimedia projector
or television and show not just photos, but also text and
graphics. The EPSON Photo File Uploader3 lets you
transfer images from your computer to your camera’s
memory card. Anything you can display on your computer
screen can be captured, converted, and uploaded. You can
create and show a presentation without printing overhead
transparencies or slides, and without a laptop computer.
Uploading Images to the Camera
The EPSON Photo File Uploader3 software allows you to
convert any image or presentation slide to the EPSON Photo
file format and upload it to your CompactFlash memory
card.
You can upload images in 640 × 480 pixel, 1600 × 600 pixel,
or 1600 × 1200 pixel sizes. EPSON Photo File Uploader3
automatically converts images from their original size to
This chapter explains the following:
◗
Uploading images to the camera’s memory card
◗
Converting presentations
◗
Projecting your presentation
whichever of these sizes you choose.
NOTE
Images that have been cropped will display black strips in the
areas that have been cropped out.
Using Your Camera for Presentations 11-1
A
11
B
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Uploading Images From Your Windows PC
NOTE
Before you start, make sure the camera is connected to your
If you want to upload images from a network drive, you may
computer, the computer is on, and the camera dial is turned
to . Then follow these steps:
need to map the drive before opening the EPSON Photo File
Uploader3 software. See your Windows documentation for
more information.
1
Start the EPSON Photo File Uploader3 program. Click
Start, point to Programs, EPSON PhotoFile
Uploader3, then click EPSON Photo File
Uploader3. You see a screen like the one on the right.
NOTE
Only one application at a time can access the camera. Make
sure neither EPSON Photo!3 nor Image Expert are running.
2
Use the Drive and Folder lists to locate the folder
containing the images you want to upload. Double-click
the folder to select it.
The images in the folder are listed in the File Name
box.
check this box for helpful information
11-2 Using Your Camera for Presentations
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
3
Select the format of the images you want to upload from
the File Type list.
4
Select the images you want to upload in the File Name
list. Then click the –> button. If you want to upload all
5
For each file in the Selected Files List, choose an
image size from the Image Size box. The File Uploader
resizes your files during the transfer process.
If you want to save copies of the converted files on your
the images in the list at once, click the >> button.
computer, click the Save file to checkbox. Click
As you select files, they appear in the Selected Files
Browse, then select the folder where you want to save
the files. Click OK. The folder you selected is displayed
List in the order they will be uploaded. This determines
the sequence in which you can display the images.
◗
to the right of the Browse button.
To rearrange the uploading (and display) order,
select the image you want to reorder, then click the
↑ or ↓ sort arrow.
◗
If you want to change your selection, click the <–
button to remove selected files or click the <<
button to remove all the files from the Selected
Files List.
◗
size of
previewed
image in
pixels
If you want to preview a selected image and confirm
its size, click the Preview checkbox.
Using Your Camera for Presentations 11-3
A
11
B
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
6
Click the Start button to start uploading the images.
8
EPSON Photo!3 opens and displays the images you
selected:
Click Upload/Copy.
The Upload/Copy Photos dialog box appears:
9
Click Upload into the Camera to upload the images
to your camera’s memory card, or click Copy to a
Memory Card in a drive to upload to a memory card
installed in your computer’s PCMCIA drive; then click
Depending on the number of images, you may have to
wait a minute or so for EPSON Photo!3 to open.
OK.
The images are uploaded to the destination you selected.
7
Click Select All to select all the images, or select
individual images by clicking the thumbnails in the
If you clicked the Save file to checkbox in step 5, the
converted images are also saved to the folder you
image selection window.
specified.
11-4 Using Your Camera for Presentations
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Uploading Images From Your Macintosh
If you want to preview a selected image and confirm its
Follow these steps to upload images to your camera from
size, click the Preview checkbox. It takes a few seconds
longer to select images with previews displayed.
your Macintosh:
1
Make sure the camera is connected to the computer, that
the computer is turned on, and the camera dial is turned
to
2
.
Double-click the EPSON Photo File Uploader 3 icon
in the EPSON Photo File Uploader folder. The
EPSON Photo File Uploader3 dialog box opens, as
shown on the right.
NOTE
Only one application at a time can access the camera. Make
sure neither EPSON Photo!3 nor Image Expert are running.
check here for helpful information
3
Click Add. The Select Files dialog box appears.
4
Double-click the folder containing the images you want
A
11
B
to upload, then select each file you want to upload and
click Select.
Using Your Camera for Presentations 11-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
5
When you finish selecting image files, click Done to
7
close the Select Files dialog box. The selected images
appear in the Selected File List in the order they will
Click Upload. A window opens to show you the
progress of the file conversion. Then EPSON Photo!3
opens and displays the images you selected:
be uploaded. This determines the sequence in which you
can display the images.
◗
To rearrange the uploading order, select the image
you want to reorder, then click Up or Down.
◗
To remove files from this list, select the file(s) and
click Remove.
6
For each file in the Selected File List, select an image
size from the Image Size box. The File Uploader will
resize your files during the transfer process.
If you want to save copies of the converted files on your
computer, click the Save file to checkbox before
uploading the photos. Click Browse to open the Select
Folder dialog box, then select the folder where you want
to save the files. Click Select: to close the Select Folder
dialog box. The folder you selected is displayed to the
right of the Browse button.
11-6 Using Your Camera for Presentations
8
Click Select All to select all the images, or select
individual images by clicking the thumbnails in the
image selection window.
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
9
Click Upload. The Upload/Copy Photos dialog box
Converting Presentations
appears.
If you want to upload a presentation or document that is not
saved as a standard image file, you can make a “screen
capture” of your computer desktop with the file open. This
lets you turn any document or presentation into a series of
image files that you can convert and upload to your camera’s
memory card.
NOTE
If you want to upload a PowerPoint presentation, you don’t need
10 Click Upload into the Camera to upload the images
to your camera, or click Copy to a Memory Card in a
drive to upload to a memory card installed in the
PCMCIA drive of your Macintosh; then click OK. The
images are uploaded to the destination you selected.
If you clicked Save file to in step 6, the converted
images are also saved to the folder you specified.
to use this conversion procedure. You can save the slides as JPG
files in PowerPoint, and then upload them into the camera.
Choose Save As from the PowerPoint File menu and choose
JPEG File Interchange Format as the file type.
Windows users can make screen captures from within the
EPSON Photo File Uploader3 utility; Macintosh users need
to use the standard Macintosh screen capture function.
11 Click Close to exit EPSON Photo!3.
Using Your Camera for Presentations 11-7
A
11
B
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
Capturing Windows Screens
Before you start, make sure the camera is connected to your
computer, the computer is turned on, and the camera dial is
turned to . Then follow these steps:
1
4
Specify the key combination you want to use for screen
captures in the Hot Key setting box. Click the ALT,
CTRL, or SHIFT checkbox, then select a function key
from the hot key list. The default hot key is F5.
Start the EPSON Photo File Uploader3 program. Click
Start, point to Programs, EPSON Photo File
choose the key combination to use for capturing screens
Uploader3 Ver.1, then click EPSON Photo File
Uploader3. You see the EPSON Photo File Uploader3
window.
NOTE
Only one application at a time can access the camera. Make
sure neither EPSON Photo!3 nor Image Expert is running.
2
Click the Screen Capture tab. The Screen Capture
dialog box appears, as shown on the right.
3
Use the Drive and Folder lists to select the folder where
you want to save the screen capture. To create a new
folder for the images, click the New Folder button.
11-8 Using Your Camera for Presentations
set the drive and folder for saving screen captures
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
5
Click Start to activate the key combination. When the
8
key combination is activated, the Start button changes
to a Stop button. The key combination remains active
6
When you’re finished, close your application and click
the Stop button on the Screen Capture dialog box. The
key combination you selected is erased.
only for the current session. To deactivate the hot key
combination, press the Stop button.
If you want to upload your screen captures to the camera’s
Start your application and open the file to the page or
image you want to capture.
The screen capture files appear in the File Name list. Then
follow the uploading instructions starting with step 4 on
memory card right away, click the Upload To Camera tab.
page 11-3.
NOTE
The entire screen is captured, not just the active window.
TIP
Make sure you maximize your presentation before you
Presentations using large fonts (at least 18 point) work best.
capture it. If you set your application to “slide show” mode
(or the equivalent) you can capture just the image you want,
without menus and other screen elements.
Capturing Macintosh Screens
EPSON Photo File Uploader3 for the Macintosh does not
7
Press the hot key combination you selected.
have a screen capture feature. However, you can make screen
captures using your Macintosh system software, then use
Your screen capture is assigned a file name and saved to
EPSON Photo File Uploader3 to upload the screen captures
to your camera’s memory card.
the folder that you specified.
You can make as many screen captures as you’d like;
simply open each file you want to capture and press your
screen capture key combination again.
The procedure may differ slightly, depending on your
Macintosh. See your computer manual for more
information.
Using Your Camera for Presentations 11-9
A
11
B
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
Make sure the camera is connected to your Macintosh, the
computer is turned on, and the camera dial is turned to
Then follow these steps:
1
NOTE
.
◗
active window. Press the Command, Shift, and 4 keys at
the same time, then click the window you want to capture,
Start EPSON Photo File Uploader3. Double-click the
or drag the cursor around that portion of the screen you want
EPSON Photo File Uploader 3 icon in the EPSON
Photo File Uploader folder. The EPSON Photo File
Uploader3 dialog box appears.
2
to capture.
◗
window as large as possible before you capture it. If you set
Start your application and open the file for the image
Press the Command, Shift, and 3 keys on your
computer keyboard at the same time. Your Macintosh
If you’re running OS 7.5x, the entire desktop is captured, not
just the active window. Make sure you make your document
your application to “slide show” mode (or the equivalent),
you want to capture.
3
If you’re running OS 8.0 or later, you can capture just the
you can capture just the image you want, without menus
and other screen elements.
4
When you’re finished, close your application.
names and saves the screen shot on your hard drive (not
in a folder).
To upload your screen shots to the camera, click the EPSON
Photo File Uploader3 window to make it active, then follow
You can make as many screen shots as you’d like; simply
repeat this step.
the uploading instructions starting with step 3 on page 11-5.
11-10 Using Your Camera for Presentations
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
Projecting Your Presentation
You can display the uploaded images on a multimedia
projector, television, or other video output device. Use the
2
Open the camera’s connector cover and connect the
black end of the video cable to the Video Out port, as
shown below:
video cable that came with your PhotoPC 800.
NOTE
Using the optional AC adapter is highly recommended when you
project your presentation. See page A-2 for instructions and
ordering information.
Follow these steps:
1
Make sure your camera and TV or video projector are
turned off.
A
11
B
Using Your Camera for Presentations 11-11
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
3
Connect the yellow end of the video cable to the
You can use the camera’s slide show feature to play your
VIDEO IN port on the TV or projector.
images automatically, or play them one at time using the
navigation buttons. You can use all of the camera’s other
playback features to show your presentation.
4
Turn on the TV or video projector and switch it to
video mode.
5
Turn the camera dial to
.
The last image that you uploaded to the camera is projected.
If you are using the optional AC adapter, you can also see the
image on the LCD screen.
11-12 Using Your Camera for Presentations
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
12
Y
Printing Directly From the Camera
our PhotoPC 800 camera lets you print your
pictures directly to any of several EPSON Stylus® color
ink jet printers, without using a computer. You can choose
NOTE
Using the optional AC adapter is highly recommended when
you’re printing from the camera. The adapter should be available
from a number of layout options, select the type and size of
where you bought your camera. Or, see the Introduction for
the paper you want to use, and print using optional filters
and print modes. You can print directly from the camera to
information on ordering an adapter from EPSON Accessories.
any of the following printers:
This chapter includes the following information about using
the Direct Print program, which comes preinstalled in your
◗
EPSON Stylus Photo
◗
EPSON Stylus Photo 700
◗
EPSON Stylus Photo EX
◗
EPSON Stylus Photo 750
◗
EPSON Stylus Photo 1200
◗
EPSON Stylus COLOR 740
camera:
◗
Connecting the camera to the printer
◗
Starting Direct Print
◗
Printing
◗
Removing and reinstalling the Direct Print program
◗
Reading error and status messages
Printing Directly From the Camera 12-1
A
B
12
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
NOTE
The Direct Print program is designed to print on special ink jet
media, including Photo Quality Ink Jet paper or cards, glossy film,
Photo Paper, and photo stickers. If you use plain paper, your
pictures will not print with the highest quality. See your printer
user’s guide for information on special ink jet media available
from EPSON.
Connecting the Camera to the
Printer
Before you start, make sure you have the Macintosh/Direct
Print serial cable that came with your camera. Then follow
these steps to connect your camera to the printer:
1
Make sure both the camera and printer are turned off.
2
Connect the round end of the serial cable to the serial
connector on the back of the printer. Make sure the
arrow on the connector faces up.
12-2 Printing Directly From the Camera
3
Open the connector cover on the side of the camera.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
4
Align the connector on the square end of the serial cable
and the camera’s serial port. Then insert the connector.
4
DirectPrint appears on the LCD screen. Press the top
button (next to DirectPrint).
You see the Direct Print main menu:
Follow the steps in the next section to print different types of
projects.
Starting Direct Print
Follow these steps to start Direct Print:
NOTE
1
Make sure the printer is turned off.
while using Direct Print.
2
If you have the optional AC adapter, connect it to the
camera to save battery power (see page A-2 ).
3
Turn the camera’s dial to
You can press the MENU button to return to the previous screen
A
B
12
.
Printing Directly From the Camera 12-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Printing
Printing Single and Multiple Images
You can print any selected image(s) or all the images in your
The Print and Print All formats let you print both single
camera on various types of paper. You can print full size
and multiple images on a page. These formats allow the
greatest variety of options. You can print on different paper
images, sticker sheets with multiple copies of the same image,
and greeting cards. You can even create an album of your
images with descriptive text next to each photo. The Direct
Print main menu offers these choices:
sizes with an assortment of layouts, and you can use any of
the available filters, paper types, or print modes. The
following table shows the way the printout appears for
different paper sizes.
Print format
Description
Print All
Prints all the images stored on the memory card. You can
print more than one copy of selected images.
Layout
options
Lets you select the image(s) you want to print. You can
print more than one copy of selected images.
3.5 × 5
Print
Index
Prints a small thumbnail image of every picture on your
memory card on contact sheets.
Album
Lets you print an album of selected pictures, with up to
three different images on one sheet of paper. You can
print one copy of each image.
Sticker
Prints 16 small or 4 larger copies of the selected image
on sheets of EPSON Photo Stickers.
Paper Size options
Letter
A A
A6
A4
—
A A
A
A A
A A
5×7
—
—
A
6.5 × 8.5
8 × 10
A
—
A
—
A
A
—
—
10 × 12
—
—
—
A
12-4 Printing Directly From the Camera
A
A
The following sections explain how you use these print
formats to set up and print different types of projects.
A3
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Load your paper in the printer following the instructions in
NOTE
your printer user’s guide, then follow these steps:
1
On the Direct Print main menu (shown on page 12-3),
select your print format. If you want to print all the
images on your memory card, press the top button (next
to Print All). If you want to print selected images, press
the + button (next to Print). You see a screen similar to
the following:
2
The Paper Size and Layout settings are linked, so sometimes
you’ll see the Layout setting change as you cycle through
Select your Paper Size and Layout settings by pressing
the button next to the setting. For example, to select
Letter as the Paper Size setting, press the button next to
Paper Size (the top button) until you see Letter
the available Paper Size options.
3
Press the W.B. button (below the down arrow) if you
want to change the Information or Filter settings. You
see a screen similar to the following:
Press the top button (next to Information) to change
the Information setting. When the Information setting
is On, your pictures print with the date and time they
were taken.
A
B
12
displayed beneath the setting.
Printing Directly From the Camera 12-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
Press the + button (next to Filter) to cycle through the
5
If you want to select specific images (or print more than
filter choices if you want to modify the color of your
printout. You can choose Monochrome to print your
one copy of some images), press the bottom button
(next to Photo Selection). You see thumbnail images
images in black and white, Blue to print them in blue
tones, or Sepia to print them in brown tones for an
of the first nine photos in the camera’s memory card,
with the currently selected image framed in white.
old-fashioned look. If you select None, your color
images print in color and your black and white images
print in black and white.
4
When you’re done making changes to the Information
and Filter settings, press the W.B. button again to return
to the previous screen.
NOTE
You don’t have to select images if you’re using the Print All
format. However, you can choose to print more than one
copy of some images.
12-6 Printing Directly From the Camera
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
6
To select a different picture, press the ISO button
NOTE
(below the left arrow) or the W.B. button (below the
right arrow) to move the selection frame backward or
Rotation is only available for Letter, A6, A4 and A3 Paper
Size settings.
forward through your pictures.
7
Now select the number of copies of your picture that
you want to print. Press the + button (next to the up
arrow) or the − button (next to the down arrow) to
increase or decrease the number of copies. A checkmark
appears on your selected photo. (If you select 0 copies,
the checkmark disappears.)
8
9
When you’re finished selecting your picture(s), press the
MENU button (beneath BACK). You see a
confirmation of your selection. If your selection is
correct, press the bottom button (next to Done).
If you need to change your selection(s), press the top
button (next to Cancel) and repeat steps 5 through 9.
If you want to rotate your picture 90 degrees in either
direction for printing, press the button next to Rotation
(the bottom button). An orientation icon appears on the
thumbnail image:
to rotate clockwise 90 degrees, or
to rotate counterclockwise 90 degrees. Press the
button to cycle through the rotation options or turn off
rotation.
A
B
12
Printing Directly From the Camera 12-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
Producing Your Printout
3
either Normal, Fine, or Fast printing mode. Fine
print mode produces a higher-resolution, slower
Before you print, you’ll need to make a few more Direct
Print settings. Follow these steps:
1
Press the bottom button (next to Print Mode) to select
printout. Fast print mode produces a quicker, lowerresolution printout.
Press the ISO button (beneath Print). The current print
settings appear on the screen (your settings may vary).
4
If you need to adjust the printing position of your paper,
press the top button (next to Adjust). You see an
adjustment screen like this one.
2
Press the + button (opposite Paper Type) to cycle
through the Paper Type settings and select the type of
paper or film you loaded in the printer. (The Paper Size
setting you previously selected is displayed beneath this
setting.)
5
Press the + button (next to the up arrow) or the −
button (next to the down arrow) to adjust the vertical
position. Press the ISO button (under the left arrow) or
the W.B. button (under the right arrow) to adjust the
12-8 Printing Directly From the Camera
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
horizontal printing position. The position moves
NOTE
0.2 mm each time you press a button, and the current
adjustment distance is displayed on the screen.
6
If you need to cancel printing, hold down the MENU button.
The status light turns red and a cancellation message
appears briefly on the LCD screen. You see the print settings
When you’re finished, press the MENU button (beneath
screen again. Repeat this step to resend your print job.
BACK) to return to the print settings menu.
7
Press the ISO button (beneath Print) to begin printing.
You see a confirmation message, then the LCD screen
goes blank. The status light begins blinking and the star
icons march across the status display panel on top of the
camera. Depending on the Print Mode option you
8
When you finish printing, the print settings screen
reappears on the camera’s LCD screen. Press the MENU
button (beneath Back) several times to exit Direct Print.
Then turn the camera dial to Off and turn off the
printer.
selected, it may take a moment for your printer to begin
printing.
If you see an error message while printing, see page
12-17 for instructions.
A
B
12
Printing Directly From the Camera 12-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
Printing a Card
Follow these steps:
You also use the Print format to print cards. EPSON Photo
Quality Ink Jet cards are perfect for snapshots, photo
postcards, and many other uses. The following table shows
1
press the + button (next to Print) to select your print
format. You see a screen similar to the following:
the available paper sizes and layouts for your cards.
Layout
options
On the Direct Print main menu (shown on page 12-3),
Paper Size options
Letter
Card Top
—
Card
Middle
—
Card
Bottom
—
A6
A
A3
A4
PhotoCard
—
—
—
—
—
—
—
—
—
A
A
2
Select your Paper Size and Layout settings by pressing
the button next to the setting. Available paper sizes for
cards are A6 and PhotoCard. (If your Paper Size is set
PhotoCard
—
—
—
12-10 Printing Directly From the Camera
—
A
to PhotoCard, the Layout is automatically set to
PhotoCard.)
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
3
Press the W.B. button (below the down arrow) if you
Printing Album Images
want to change the Information or Filter settings. (See
page 12-5.) When you’re done, press the W.B. button
The Album print format lets you print an “album” of
again to return to the previous screen.
4
Press the bottom button (next to Photo Selection) to
select your image. Select a single image for your card. If
your Paper Size setting is A6, you can rotate your image.
(See page 12-7.)
5
When you’re ready to print your card, follow the steps
on page 12-8.
selected images on Letter or A4-size paper. Up to three
images are lined up on the left side of the page. If the
Information setting is On, descriptive information about
each image is automatically added on the right. The
following table lists Layout and Paper Size options, and
shows the way your printouts appear:
Layout
options
Paper Size options
Letter or A4
Album
A
A
A
A
A
A
A
A
A
A
B
12
Printing Directly From the Camera 12-11
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
Load your paper in the printer, then follow these steps to
3
want to change the Information or Filter settings. (See
page 12-5.) When you’re done, press the W.B. button
print album images:
1
On the Direct Print main menu (shown on page 12-3),
press the bottom button (next to Album) to select your
print format. You see a screen similar to the following
again to return to the previous screen.
4
(the Paper Size setting defaults to A4 or Letter):
Select your Paper Size setting by pressing the button
next to the setting. (The Layout setting is automatically
set to Album.)
12-12 Printing Directly From the Camera
Press the bottom button (next to Photo Selection) to
select your images. (See page 12-6.)
5
2
Press the W.B. button (below the down arrow) if you
When you’re ready to print your album, follow the steps
under “Producing Your Printout” on page 12-8.
Altair.book Page 13 Thursday, July 1, 1999 3:33 PM
Printing Stickers
Load your photo sticker sheets in the printer, following the
When your print format is set to Sticker, you can print 16
instructions that came with the stickers. Then follow these
steps:
small or four larger copies of a single image on sheets of
EPSON Photo Stickers. You can select the following Paper
Size and Layout settings:
print format. You see a screen similar to the following
(your Paper Size setting defaults to either Stickers 16
Paper Size options
Stickers 4
or Stickers 4):
Stickers 16
A A
A A
1 photo × 16
2 photos × 8
On the Direct Print main menu (shown on page 12-3),
press the W.B. button (under Sticker) to select your
Layout
options
1 photo × 4
2 photos × 2
1
—
—
NOTE
You can order EPSON Photo Stickers (product code S041144)
from EPSON Accessories at (800) 873-7766.
2
Select your Paper Size setting by pressing the top button
(next to Paper Size). The Paper Size and Layout
settings are linked, so the Layout setting automatically
A
B
12
changes.
Printing Directly From the Camera 12-13
Altair.book Page 14 Thursday, July 1, 1999 3:33 PM
NOTE
6
If your selection is correct, press the bottom button
(next to Done). If you need to change your selection,
press the top button (next to Cancel) and repeat steps 4
You can’t turn Information On or select a filter when the
print format is set to Sticker.
through 5.
3
Press the bottom button (next to Photo Selection) to
select the image you want to print on your stickers. You
see thumbnail images of the first nine photos on the
camera’s memory card, with the currently selected image
framed in white.
4
To select a different picture, press the ISO button
(beneath the left arrow) or the W.B. button (beneath the
right arrow) to move the selection frame backward or
forward through your pictures.
5
When you’ve selected your image, press the + button
(next to the up arrow) to select 1 Copy. (You can’t
rotate the image.) Then press the MENU button (under
BACK). You see a confirmation of your selection.
12-14 Printing Directly From the Camera
7
When you’re ready to print your stickers, follow the
steps on page 12-8. You may want to make a test print
to make sure your pictures are aligned properly. Then
you can use the Adjust setting to align them for your
final printout.
NOTE
The Paper Type setting is automatically set to Glossy Film
and you can choose only Fine or Normal print modes.
Altair.book Page 15 Thursday, July 1, 1999 3:33 PM
Printing an Index of Your Images
Follow these steps to print an index of all your images:
The Index print format lets you print a contact sheet with
thumbnail images of all the images on your memory card.
The following table shows how your printout will look:
Layout
options
1
press the − button (next to Index) to select your print
format. You see a screen similar to the following (your
Paper Size setting will be different):
Paper Size options
Letter or A4
On the Direct Print main menu (shown on page 12-3),
A6
Index
2
Select your Paper Size setting by pressing the top button
(next to Paper Size). You can choose Letter, A6, or
A4. The Layout setting is automatically set to Index.
A
B
12
Printing Directly From the Camera 12-15
Altair.book Page 16 Thursday, July 1, 1999 3:33 PM
3
If you want to print information for each image, press
Removing the Direct Print Program
the W.B. button (under the down arrow) to go to the
following menu. Then press the top button (next to
Direct Print comes pre-installed on your camera, but you can
Information) to turn it On.
plan to use it. You can always install the program later, if you
need it. Follow these steps:
use the EPSON Program Uploader to remove it if you don’t
1
Connect the camera to your computer. (See Chapter 6
for instructions.) Then turn the camera’s dial to
2
.
Start EPSON Program Uploader. Under Windows,
click Start, then point to Programs, EPSON
Photo!3 Ver. 1, EPSON Program Uploader. You
NOTE
You can’t apply special filters if you’re using the Index print
format.
4
When you’re done, press the W.B. button again to
return to the previous menu.
5
When you’re ready to print your index, follow the steps
on page 12-8.
12-16 Printing Directly From the Camera
see a screen similar to the following:
Altair.book Page 17 Thursday, July 1, 1999 3:33 PM
3
Select Direct Print V3.0 in the Applications in
5
Camera listbox.
Select Direct Print V3.0 in the Applications in
Folder listbox.
4
Click Remove. You see a confirmation message asking
if you’re sure you want to remove it.
5
Click Yes to remove the program, or No to cancel.
Then click Close to exit Program Uploader.
6
Click the Upload button. You see a progress meter, and
after a moment Direct Print V3.0 appears in the
Applications in Camera listbox.
7
Click Close to exit.
Reinstalling the Direct Print Program
Reading Error and Status Messages
Follow these steps to reinstall the Direct Print program to
your camera:
If you see an error or status message on the camera’s LCD
screen or status display panel, check the following tables to
1
Connect the camera to your computer and turn the
camera’s dial to
.
respond to the message.
LCD screeen messages
Message
Description
program starts automatically, exit the program.
No Photos in Memory.
There are no pictures in the camera’s memory.
Press any button to return to the main menu.
3
Start EPSON Program Uploader.
Please Select at least
one photo to print.
4
When you see the EPSON Program Uploader screen,
You haven’t selected the picture you want to
print. Press the button next to OK (the bottom
button), then press the button next to Photo
Selection (the bottom button) and select a
picture.
2
Insert your CD-ROM in your drive. If the install
click Browse to navigate to the root directory of your
CD-ROM drive.
Printing Directly From the Camera 12-17
A
B
12
Altair.book Page 18 Thursday, July 1, 1999 3:33 PM
LCD screeen messages
LCD screeen messages
Message
Description
Message
Description
Unsupported printer
model. Please connect
supported model.
The camera is connected to an incompatible
printer. Connect the camera to one of the
compatible EPSON Stylus models listed on page
12-1. Hold down the MENU button to cancel
printing.
Printing canceled.
You held down the MENU button to cancel
printing. The message disappears after three
seconds.
Printing canceled.
Reset printer and
camera.
A printing error occurred. The message
disappears after three seconds. Turn off the
camera and printer, then turn them on and try
printing again.
Connection or printer
error.
Printing stopped because of a printer error. Check
your printer and clear the error (you may need to
turn the printer and camera off and then on again),
then restart printing from the beginning. (See your
printer user’s guide for troubleshooting
information.)
OK to erase printing
settings?
You are about to erase the current print settings.
Press the button next to YES (the bottom button)
to erase the settings, or press the button next to
NO (the top button) to save the settings and
return to the previous menu.
Batteries are low. Use
AC adapter.
Battery power is almost out. If you have the
optional AC adapter, connect it to continue.
Otherwise, replace the batteries with batteries
that have been fully charged.
Error. Settings reset to
default.
An unknown error occurred and your settings
were returned to their defaults. Press the bottom
button to return to the main menu and enter your
print settings again.
Insert a Memory Card
in the camera.
No memory card is installed in the camera, or the
memory card is not fully inserted into its slot.
Insert a memory card as described on page 1-10.
12-18 Printing Directly From the Camera
Status display panel messages
Message
Description
E51: Another interface
is active
The printer is receiving a print job from another
source (through a different interface). When that
print job is finished, the printer begins printing
from Direct Print automatically.
E55: No ink
Printing has stopped because the printer ran out
of ink. Replace the ink cartridges and restart
printing from the beginning. See your printer
User’s Guide for instructions on replacing ink
cartridges.
E56: No paper or paper
jam
Make sure paper is loaded in the printer, then
press the printer’s E Load/Eject button to begin
printing.
If paper is jammed in the printer, follow the
instructions in your printer User’s Guide to clear
the jam. Then restart printing from the beginning.
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
13
.
13 Maintenance and Troubleshooting
Y
our PhotoPC 800 camera is easy to take care of, and
any problems you may have are easy to solve. This
Cleaning the Camera and Battery Charger
◗
Unplug the battery charger before cleaning.
chapter includes the following sections:
◗
Use a clean, dry cloth to wipe the camera free of dust.
◗
Caring for the camera and battery charger
◗
Use a damp cloth for cleaning the battery charger.
◗
Solving camera problems
◗
Keep the battery charger terminals clean by wiping them
◗
Solving picture problems
with a dry cloth.
◗
Caring for the Camera and Battery
Charger
Don’t use harsh or abrasive cleaners. Don’t use liquid or
aerosol cleaners.
◗
Your PhotoPC 800 requires only basic care. Before you
To clean the lens, first blow off any loose dust or dirt.
Then breathe on the lens and wipe off all moisture with
perform any maintenance procedures, be sure to read the
safety instructions in the Introduction. Then observe the
a soft, lint-free cloth or lens cleaning tissue. To avoid
A
scratching the lens, don’t press too hard.
following guidelines.
B
Maintenance and Troubleshooting 13-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
◗
If necessary, clean the battery contacts with a dry cloth.
◗
In areas of excessive dirt or dust
◗
If the LCD screen gets fingerprints or smudges on it, use
◗
Where it will be exposed to strong vibrations or
magnetic fields
a soft, damp cloth to lightly wipe the screen.
Storing the Camera
Solving Camera Problems
◗
Before you call for help, check this list of problems and
possible solutions:
When you’re not using the camera, keep the lens cover
closed and store the camera in the soft case that came
with it. Make sure the camera dial is set to Off.
◗
When the camera is not used for long periods of time,
remove the batteries and store them at a low temperature
The camera has no power.
◗
If you’re using batteries, the camera may have shut off
automatically to conserve battery power. If your camera
dial is set to , or , press the shutter button to turn
in a dry location. This prevents camera damage from
battery leaks or corrosion.
Do not store the camera in the following locations:
the power back on. If your camera dial is set to or ,
press any button on the back of the camera to turn the
◗
Where it will be exposed to direct sunlight, for example,
on a car dashboard
power on. (You can also turn the power on by turning
the camera dial to Off and then back to its former
◗
Near sources of bright light or high humidity
◗
Near heat sources or in a closed car or trunk
13-2 Maintenance and Troubleshooting
position.)
◗
Check the batteries and make sure they’re installed
correctly. Recharge or replace the batteries.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
◗
The flash doesn’t work.
into a working outlet.
◗
Make sure the flash is not set to the flash off setting.
◗
Check the batteries and make sure they’re installed
You can’t take a picture with the camera.
◗
◗
correctly. Recharge or replace the batteries if necessary.
The flash may be recharging. Wait until the status light
turns green, and try again.
◗
Make sure you’ve installed the CompactFlash memory
Nothing appears on the LCD screen.
card in your camera. If it’s already installed, you may
need to format or eject it. Check to see if a message is
◗
◗
Check your batteries and make sure they’re installed
◗
Make sure the lens cover is open.
picture counter on the display panel. Erase some pictures
(see Chapter 5), or transfer the pictures to your
◗
Make sure you’ve installed and formatted the
CompactFlash memory card.
computer and then erase them (see Chapter 6). Or
◗
The camera may have shut off automatically. If your
The CompactFlash memory card may be full. Check the
replace your memory card with a new one.
camera dial is set to
The camera may be connected to your computer. When
it’s connected, you can’t use any of the controls on the
turn the power back on. If your camera dial is set to
or , press any button on the back of the camera to
camera itself. See Chapter 10 for instructions on taking
turn power on. (You can also turn power on by turning
the camera dial to Off and then back to its former
pictures from your computer.
◗
You can’t use the flash in continuous shoot mode.
correctly. Recharge or replace the batteries if necessary.
displayed on the camera’s LCD screen.
◗
13
If you are using the AC adapter, make sure it’s plugged
Make sure the lens cover is open.
or
, press the shutter button to
position.)
Maintenance and Troubleshooting 13-3
A
B
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
◗
Make sure the camera is not in
viewfinder mode.
◗
sure the TV is set to Video mode. See the manual for
your television if you need help.
The image on the screen is too dark.
◗
If your TV has both Video and S-Video modes, make
Adjust the brightness of the screen using the Camera
SETUP menu. See page 4-28 for instructions.
◗
Check your batteries and make sure they’re installed
correctly. Recharge or replace the batteries if necessary.
The menus disappear while you’re taking pictures with the
The “pictures remaining” number on the display panel
LCD screen.
doesn’t decrease after you take a picture.
◗
◗
The menus disappear when you press the MENU
button. Press the MENU button again to make them
reappear.
Your camera is operating correctly. The total number of
pictures you can store depends on your pictures’
content. The number doesn’t always change, especially
when you’re using standard image quality.
Nothing appears on the television when you connect your
camera to it.
You get an error message when you try to transfer your
◗
pictures to the computer.
Make sure the video cable is connected correctly, as
described on page 11-11, and the camera and TV are
◗
turned on.
◗
Make sure your camera dial is set to
Make sure the cable is connected correctly as described
in Chapter 6.
.
◗
Make sure your camera is turned on and the batteries
have enough power.
13-4 Maintenance and Troubleshooting
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
◗
Check the serial port settings in your Image Expert or
EPSON Photo!3 software. You may need to change the
Port and Speed serial connection settings to Auto.
◗
If you’re using a Windows system and have trouble
connecting to the COM port, check the computer’s
COM port settings. Make sure the port is properly
configured and that the Base I/O port address and the
◗
Check the port setting in your Windows Control panel.
You may need to set your port to a faster speed, lower
the FIFO buffer size (advanced serial port
configuration), or adjust the speed in your software. See
“Adjusting Camera Settings From Your Computer” on
◗
◗
13
EPSON Photo!3 open at the same time.
You get a “The Camera Is Not Responding” error message
when you’re using your PhotoPC 800 software with the
camera connected to your computer.
◗
Make sure the cable is connected correctly as described
in Chapter 6. Also make sure your camera dial is not
turned Off and the batteries have power.
Interrupt Request Number (IRQ) assigned to the port
are not in conflict with any other devices.
◗
Make sure you don’t have both Image Expert and
◗
Check the serial port settings in your Image Expert or
EPSON Photo!3 software. You may need to change the
Port and Speed serial connection settings to Auto.
◗
If you were able to use the camera with the computer
page 10-5 for more information.
previously and then changed or added other settings on
your system, you may have a COM port conflict. Try
If you’re using a Macintosh and the camera is sharing a
serial port with another device, turn AppleTalk off.
using a different COM port or reconfiguring the COM
port settings. (See your Windows documentation for
If your camera is connected to a USB hub, try
connecting the camera directly to your computer.
instructions.) If you were not able to use the camera
with your computer previously, you may have an
inoperable serial cable. Try using another cable.
Maintenance and Troubleshooting 13-5
A
B
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
◗
If your camera is connected to a USB hub, try
◗
Macintosh documentation for more information.
connecting the camera directly to your computer.
◗
Try turning off any unnecessary extensions. See your
Avoid opening or working with other software
The pictures transfer to your computer too slowly.
applications while the camera and computer are
communicating.
◗
If your system has less than 32MB RAM, the transfer
speed may be slow. Try using virtual memory. See your
You are unable to drag and drop photos into a document.
◗
◗
If your system has less than 32MB RAM, you may not
be able to use drag and drop. Make sure you don’t run
computer documentation or system help for more
information.
◗
Check the port setting in your Windows Control panel.
too many applications at the same time. You may need
You may need to set your port to a faster speed. See your
to add memory to your system or use another method of
getting photos into your documents.
Windows documentation or help system for more
information.
Your application may not support this method of adding
◗
If you’re transferring pictures to an application through
EPSON Photo!3 and you use the PhotoEnhance™
pictures.
feature, the transfer will take longer. Try transferring
without PhotoEnhance.
You are unable to copy and paste or import your photo into
a document on your Macintosh.
◗
Try increasing your virtual memory using the Memory
Control Panel. Also increase the memory allocation for
your word processor or other application. (Select the
application and choose Get Info from the File menu.)
13-6 Maintenance and Troubleshooting
You get a TWAIN error message when you try to transfer
images with Adobe Photoshop.
◗
Make sure you select TWAIN_32, not TWAIN.
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
You are unable to format or use a CompactFlash storage
Your notebook computer’s PCMCIA drive can’t access a
card with your camera.
CompactFlash storage card with a PCMCIA adapter.
◗
◗
Make sure you’re using an ATA-compatible
CompactFlash card. Other cards may not work with
PhotoPC 800. If you need help with a card, call the
appropriate number:
◗
Lexar Media, (800) 789-9418
◗
SanDisk, (408) 542-0595
If you’re using an IBM Thinkpad,™ you may need an
updated driver for your PCMCIA port. Call IBM
technical support.
When you upload pictures to a storage card in your
computer, your system appears to hang.
◗
Check the status bar at the bottom of your screen. If it
You’ve purchased a CompactFlash card that doesn’t fit in
shows that the transfer is complete, your system is
the camera.
operating correctly. You may have to click your mouse
to change the hourglass icon to a normal pointer.
◗
◗
Make sure you purchased the correct size CompactFlash
card (1.7 inches wide × 1.5 inches high × 0.13 inch
When you copy image files from your computer to a
deep).
storage card in your PCMCIA drive, the camera can’t
Make sure you’ve installed the card correctly. The card’s
label should be facing the front of the camera, and the
access the images.
arrow(s) on the label should point down.
13
◗
You can’t use this method to upload pictures to the
camera. You have to use the EPSON Photo File
A
Uploader3 to convert and upload your images.
B
Maintenance and Troubleshooting 13-7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
Solving Picture Problems
When you preview images on your computer, they look
If you’re not satisfied with some of the pictures you get from
distorted.
the PhotoPC 800, you may need to adjust some of the
◗
camera settings. Read the suggestions below.
If you are using an STB® Velocity 128 video card and
have a screen resolution of 800 × 600 or 640 × 480, you
Your pictures display poor image quality on the screen or
may notice this phenomenon. Slowing down the
acceleration on your video card may solve this problem:
when you print them out.
◗
Click Start, point to Settings, click Control Panel,
PhotoPC 800 captures images in 24-bit color
then double-click System Properties. On the
Performance tab, click the Graphics button. Select a
(16.7 million colors). Your pictures will not display
maximum image quality if your monitor or computer’s
slower acceleration and click OK. See your Windows
documentation or help system for more information.
video controller doesn’t support this color depth. You
◗
may need to upgrade your system to achieve the best
possible image quality.
The colors in your picture don’t look right.
If your pictures look better on the screen than when you
◗
print them out, you may need to upgrade your printer.
An EPSON Stylus ink jet printer, for example, provides
excellent image quality.
◗
If you used drag and drop to insert your pictures, they
may appear grainy. Try importing them into your
documents instead.
13-8 Maintenance and Troubleshooting
When you take pictures under certain artificial lighting
conditions, the colors may be slightly distorted. You can
use your Image Expert software to adjust the colors, as
described on page 9-3.
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
Your picture is blurry or out of focus.
◗
close as 8 inches in macro mode.
When you take macro close-ups, make sure you have
adequate lighting (with the flash disabled). Using a
tripod will help you capture sharp pictures.
◗
Make sure that your subject isn’t moving and that you
hold the camera steady after you press the shutter button
(until the camera status light or photo capture light
starts flashing).
◗
If you want to photograph a moving subject, try
increasing the shutter speed. See Chapter 4 for
information about how to change the shutter speed from
the LCD menus.
◗
Make sure your flash is not set to flash off.
When you focus on a nearby object, your picture’s
13
background may appear blurry. Try changing your
focus.
Make sure your subject is within the camera’s range. You
should be at least 20 inches away to take a picture
without the flash, and 20 inches to 8 feet away to take a
picture with the flash. You can take a picture from as
◗
◗
Your picture is too dark (underexposed).
◗
You may need to use the flash. Make sure the setting is
not flash off.
◗
If you’re using the flash, make sure your subject is within
the range of 8 feet.
◗
Use Image Expert to adjust the picture’s brightness and
contrast, as described on page 9-4.
◗
Try adjusting the camera’s exposure or sensitivity
settings (Use the Manual user mode). See Chapter 4 for
details.
◗
If you’re using the macro mode to take a close-up photo,
be sure to provide adequate lighting for your subject,
since the camera’s smallest aperture setting (F8) is
A
automatically selected in this mode.
B
Maintenance and Troubleshooting 13-9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
◗
If you’re taking a picture at night and you want to light
A horizontal or vertical red line appears on your picture.
up the background as well as your subject, use the
camera’s slow synchronized flash mode.
◗
your lens.
Your picture is too light (overexposed).
◗
If you’re using the forced flash setting, it may be too
bright. Try setting the flash to Auto
◗
◗
◗
.
The wrong date and/or time are displayed on your pictures.
◗
If you’re facing a bright light source, you may need to
shoot your picture from a different angle.
Set user mode to Manual and adjust the camera’s
Part of your picture is missing.
Make sure you’re not blocking the lens with your finger,
wrist strap, clothing, or other object.
13-10 Maintenance and Troubleshooting
Whenever you change the batteries in your camera, you
need to reset the clock. You can use the LCD screen
SETUP menu or set the camera’s clock from your
computer. See Chapter 4 or Chapter 10 for more
Use Image Expert to adjust the picture’s brightness, as
described on page 9-4.
exposure setting.
◗
Red lines are caused by glare. Avoid photographing
shiny surfaces that reflect excessive amounts of light into
information.
Your pictures don’t look as good as they used to.
◗
Your camera’s lens may be dirty or dusty. Try cleaning it
by following the instructions on page 13-1.
Altair.book Page 11 Thursday, July 1, 1999 3:33 PM
13
The area captured in the photo is different from what you
saw in the viewfinder.
◗
Make sure you look straight through the viewfinder.
Keep in mind that the area visible through the
viewfinder is slightly smaller than the area captured in
the photo.
◗
If you’re taking a close-up or macro mode picture, turn
the camera dial to
so that you can use your LCD
screen to preview your picture.
A
B
Maintenance and Troubleshooting 13-11
Altair.book Page 12 Thursday, July 1, 1999 3:33 PM
13-12 Maintenance and Troubleshooting
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
A
Y
A
Optional Accessories
ou can use the PhotoPC 800 with a variety of options.
To save battery power, you can use the AC adapter.
For portraits or other studio photographs, you can attach a
tripod to your camera. You can also get additional
CompactFlash memory cards, or a second set of NiMH
batteries and a replacement NiMH Power Pak.
You can use an optional IOMEGA Clik! drive to store
photos and transfer them to your computer. Or, if your
desktop or notebook computer has a Type II PCMCIA card
slot, you can use a PCMCIA adapter to access images directly
from your memory card.
Finally, if you want to verify the authenticity of photos taken
with your camera, you can purchase the EPSON Image
Authentication System (IAS). This software detects when
even a single bit of digital data in a picture has been altered.
EPSON recommends CompactFlash memory cards from the
following manufacturers:
◗
Lexar Media, (800) 789-9418
◗
SanDisk, (408) 542-0595
Make sure you purchase the correct size card (1.7 inches
wide × 1.5 inches high × 0.13 inch deep). The PhotoPC 800
will accept ATA-compatible Type 1 CompactFlash cards up
to 96MB.
A
B
Optional Accessories A-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
For information on installing, formatting, and removing
Using the Universal AC Adapter
memory cards from your camera, see Chapter 1.
The universal AC adapter (B867062) allows you to connect
This chapter includes the following information:
your PhotoPC 800 to any standard (100 to 240 V) electrical
◗
Using the universal AC adapter
outlet. This is especially useful for transferring pictures and
operating the camera from your computer, or using Direct
◗
Using the camera with a tripod
◗
Using a PCMCIA adapter
◗
About the IOMEGA Clik! drive
Print. The adapter powers the camera but does not charge
the batteries.
WARNING
The options listed above should be available where you
bought your PhotoPC 800.
You can order any of the following accessories from EPSON
Accessories at (800) 873-7766 (U.S.) or (800) 873-7766
(in Canada for dealer referral).
Accessory
Product code
PhotoPC 800 Universal AC Adapter
B867062
NiMH Battery Pak (4 batteries)
B818061
Universal NiMH Power Pak (charger and 4 batteries)
B818172
EPSON Image Authentication System (IAS)
PPC8-IAS
A-2 Optional Accessories
◗
Use only the adapter designed for the PhotoPC 800. Using
any other adapter may cause fire, electrical shock, or injury.
◗
Do not alter the plug on the power cable, and do not use the
adapter for any other purpose than powering your
PhotoPC 800.
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
To avoid losing any images or settings, make sure the camera
3
Plug the adapter cable into the DC port on the camera.
A
is finished processing. Turn the camera off before you
connect or disconnect the AC adapter. Then follow these
steps:
1
Locate the AC power cord that came with your camera.
Push the adapter’s cable connector firmly into the AC
inlet.
4
2
Plug the AC power cord into an electrical outlet.
Open the connector cover on the side of the camera.
A
B
Optional Accessories A-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Using an Optional Tripod
Using a PCMCIA Adapter
You can use your PhotoPC 800 with any standard tripod.
A PCMCIA adapter allows you to access images stored on
Follow these steps:
CompactFlash cards directly from your computer. To use
1
this adapter, your computer must be equipped with a Type II
PCMCIA card slot.
Assemble and set up the tripod by following the
manufacturer’s instructions. Make sure the tripod is
well-balanced on a flat surface.
2
Find the opening for the tripod screw on the bottom of
your camera. Carefully place the camera on the tripod.
3
If you’re using a Macintosh, you must enable PC Exchange
extension software to access files on CompactFlash cards. See
your Macintosh documentation for information.
Screw the camera on until it is firmly in place.
Installing the PCMCIA Adapter
Adjust the tripod to view your subject as desired.
Follow these steps to install the adapter:
1
A-4 Optional Accessories
Insert the memory card all the way into the adapter.
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
2
Insert the adapter into your computer’s Type II
Transferring Photos With the Adapter
PCMCIA slot.
Once the adapter and card are installed in your computer’s
A
PCMCIA slot, you can transfer photos by simply copying
them to your hard drive. This is the fastest way to get
pictures into your computer. The image files are stored in the
Photo_1 folder on the card.
◗
In Windows, use My Computer or the Windows
Explorer to drag and drop image files to your hard drive.
◗
On a Macintosh, use the Finder to drag and drop image
files to your desktop or hard drive.
NOTE
◗
If you don’t have an adapter, you can use Image Expert to
transfer photos to your computer. See Chapter 6.
◗
If you can’t access a card in your notebook computer,
contact the computer manufacturer. See page 13-7 for more
information.
A
B
Optional Accessories A-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
About the IOMEGA Clik! Drive
You can use an IOMEGA Clik! digital camera drive to store
extra pictures when you’re on the go and read CompactFlash
cards directly from your computer. This drive saves time and
batteries because you don’t have to download pictures from
your camera to your computer. You should be able to find
the IOMEGA Clik! drive where you purchased your camera.
For additional information, visit the IOMEGA website at:
www.iomega.com. You can call IOMEGA at
(800) MYSTUFF ( [800] 697-8833) for ordering
information.
A-6 Optional Accessories
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
B
Specifications
B
Camera
Power
Sources
Physical Dimensions
Width
4.4 in (111.4 mm)
Height
2.7 in (68 mm)
Depth
1.6 in (40.2 mm)
Weight
8.3 oz (235 g)
without batteries and strap
Includes 4 AA rechargeable NiMH
batteries and pocket-size charger. Also
accepts 2 AA batteries (single-use
lithium or rechargeable NiCad)
Optional AC adapter (B867062)
Battery Life
Approximately 850 pictures using the
viewfinder
Approximately 100 pictures using the
LCD screens
Approximately 45 minutes in playback
mode
A
B
Specifications B-1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Technical
Product type
2.14 megapixel CCD (charged coupled
device) still frame auto focus camera
CCD
0.5 inch color area CCD (2.14 million
pixels)
Image resolution
1600 × 1200 pixels (fine and super fine)
640 × 480 pixels (standard)
1600 × 600 pixels (panoramic fine)
1600 × 600 pixels (panoramic super fine)
1984 × 1488 pixels* (HyPict)
1984 × 744 pixels* (HyPict panorama)
* Interpolated
Serial interface
14-pin dual line terminal to camera,
RS-232C-compatible connector to
computer (9-pin DSUB connector to PC,
8-pin mini-DIN male connector to
Macintosh or printer)
USB cable
14-pin connector (camera)
USB connector (computer)
USB
communication
speed
Up to 12 Mbps
Video out
NTSC standard
File format
JPEG
Internal memory
2MB flash program memory
Bit depth
16 million colors, 24-bit
Expansion memory
Serial
communication
speed
Up to 230.4 Kbps with high-speed serial
port (19.2 Kbps or higher), 1.8 Mbps
when connected to EPSON printers
8MB CompactFlash storage card;
also accepts optional 4MB to 96MB
storage cards (available from Lexar Media
and SanDisk)
Self-timer
10 seconds
Tripod adapter
Built-in
B-2 Specifications
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
Environmental
Photographic
Temperature
Operating: 41 to 95 °F (5 to 35 °C)
Non-operating: –4 to 140 °F (–20 to
60 °C)
Humidity
Operating: 30 to 80% (non-condensing)
Non-operating: 10 to 80% (noncondensing)
Safety
United States
FCC Part 15 Subpart B Class B
Canada
CSA C108.8 Class B
Lens
f = 7 mm (equivalent to a 38 mm lens on
a 35 mm camera)
Range
19.7 inches (50 cm) to infinity;
5.9 to 19.7 inches (15 to 50 cm) in macro
mode
LCD screen
1.8-inch active matrix TFT color LCD
(110 thousand pixels)
Sensitivity
Equivalent to ISO 100/200/400
Exposure control
Programmed auto exposure
manual adjustment: –2 to +2 EV, in halfsteps (or in 0.2 EV steps in AE mode);
spot metering and matrix metering
White balance
TTL automatic white balance
Fixed white balance (5200 °Kelvin)
User-defined white balance
B
A
B
Specifications B-3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
Shutter
Viewfinder
Focus
Electric iris with mechanical shutter,
1/2 second to 1/750 second (flash off
mode)
1/30 second to 1/750 second (auto flash
and forced flash modes)
Real-image optical, with centering
crosshair and edge border (view range
approximately 90%)
Automatic focus from 19.7 inches
(50 cm) to infinity
Automatic focus from 5.9 to 19.7 inches
(15 to 50 cm) in macro mode
Aperture
f2.4, f8.0
Flash
Automatic luminance control flash mode
Flash modes
Forced flash, automatic, flash off,
slow synchronized flash mode (can be
enabled through the LCD menus)
B-4 Specifications
Flash range:
Sensitivity setting
Normal distance
2× zoom
Std. (ISO 100)
1.6 to 11.2 ft (0.5 to
3.4 m)
1.6 to 11.2 ft (0.5 to
3.4 m)
Med. (ISO 200)
1.6 to 16.1 ft (0.5 to
4.9 m)
1.6 to 16.1 ft (0.5 to
4.9 m)
High (ISO 400)
1.6 to 22.6 ft (0.5 to
6.9 m)
1.6 to 22.6 ft (0.5 to
6.9 m)
Memory Card Picture Capacity
Image Mode
8MB Card
Standard
118
Fine/Monochrome Fine
25
SuperFine/Monochrome
SuperFine
12
HyPict/Monochrome HyPict
10
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
NiMH Battery Charger
Optional AC Adapter
Physical Dimensions
Physical Dimensions
Width
3.0 inches (76 mm)
Width
1.7 inches (43 mm)
Height
4.5 inches (115 mm)
Height
1.22 inches (31 mm)
Depth
1.1 inch (28 mm)
Depth
4.1 inches (104 mm)
Weight
Approximately 4.6 oz (130 g)
B
Technical
Technical
Input
100 to 240 V, 50 to 60 Hz
Output
DC 1.2 V/490 mA × 4
Charging time
2 batteries: approximately 110 minutes
4 batteries: approximately 210 minutes
Output
DC 3.5 V/2.5 A
Input
100 to 240 V AC, 50 to 60 Hz
CompactFlash Card
Physical Dimensions
Power consumption Approximately 8W
Width
1.7 inches (42.8 mm)
Charging
temperature
Height
1.5 inches (36.8 mm)
Depth
0.13 inch (3.3 mm)
41 to 95 °F (5 to 35 °C)
Storage temperature −4 to 86 °F (−20 to 30 °C)
A
B
Specifications B-5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
B-6 Specifications
Altair.book Page 1 Thursday, July 1, 1999 3:33 PM
Index
A
AC adapter, Intro-4, 2-3, 6-1, A-2 to A-3, B-5
Accessories, Intro-4, A-1 to A-6
Acquiring photos, TWAIN programs, 6-10 to 6-11
Adjusting camera settings, 3-1 to 3-8, 4-1 to 4-30
Albums
adding sound to images, 8-8 to 8-9
copying to diskette, 8-13 to 8-14
deleting sounds, 8-10 to 8-11
displaying as slide show, 8-11 to 8-12
dragging pictures from, 7-4 to 7-6
editing sound in pictures, 8-10
making screen saver, 8-12
organizing pictures, 8-2 to 8-3
playing back sounds, 8-9
printing from camera, 12-11 to 12-12
printing Image Expert albums, 8-4 to 8-8
renaming pictures, 8-3
setting pictures as wallpaper, 8-12 to 8-13
Alert beep, setting, 4-28 to 4-29
Aperture, setting, 4-24
AppleTalk, 6-4
Attaching wrist strap, 1-9
Audio
adding, 4-13 to 4-15, 8-8 to 8-9
deleting, 5-10 to 5-11, 8-10 to 8-11
editing, 8-10
playing back, 8-9 to 8-10
Automatic power off, setting, 4-26 to 4-27
B
Batteries
charging, 1-4 to 1-6
checking, 2-2 to 2-3
handling, 1-8 to 1-9
installing, 1-6 to 1-7
options, 1-8 to 1-9
replacing, Intro-4
specifications, B-1
A
B
Index 1
Altair.book Page 2 Thursday, July 1, 1999 3:33 PM
Battery charger, specifications, B-5
Bitmap (BMP) files, 6-13
Black and white pictures, taking, 4-4
Brightness
correcting images, 9-3 to 9-4
setting LCD brightness, 4-28
Buttons, adjusting settings with, 3-1 to 3-8
C
Cable
DirectPrint, connecting, 12-2 to 12-3
Macintosh serial, connecting, 6-4 to 6-5
USB, connecting, 6-2
video, connecting, 5-17 to 5-19, 11-11 to 11-12
Windows serial, connecting, 6-3 to 6-4
Camera
dial settings, 2-1 to 2-2
features, Intro-1 to Intro-3
identifying parts, 1-2 to 1-3
Camio Viewer, 7-6 to 7-8
Caring for camera, 13-1 to 13-2
Charging batteries, 1-4 to 1-6
Cleaning camera, 13-1 to 13-2
Clock, setting, 1-11 to 1-12, 4-29 to 4-30
Close-ups, taking, 4-7 to 4-8
2 Index
Color correcting, 9-3 to 9-4
Color depth, 9-9
CompactFlash storage cards, see Memory card
CompuServe, Intro-6
Computer, connecting camera, 6-1 to 6-5
Connecting
AC power cord, A-3
Direct Print cable, 12-2 to 12-3
serial cable, 6-3 to 6-5
USB cable, 6-2
video cable, 5-17 to 5-19
Continuous shooting, 4-10 to 4-13
using interval shooting, 4-12 to 4-13
using the timer, 4-11 to 4-12
Contrast, correcting, 9-3 to 9-4
Copying pictures
into documents, 7-3 to 7-4
to diskette, 8-13 to 8-14
Cropping images, 9-5
D
Date and time, setting, 1-11 to 1-12, 4-29 to 4-30
Deleting pictures, see Erasing pictures from camera
Digital zoom, using, 4-5 to 4-6
Altair.book Page 3 Thursday, July 1, 1999 3:33 PM
Direct Print
connecting the cable, 12-2 to 12-3
error messages, 12-17 to 12-18
index, printing, 12-15 to 12-16
multiple images, printing, 12-4 to 12-9
photo stickers, printing, 12-13 to 12-14
print formats, 12-4
reinstalling, 12-17
removing from camera, 12-16 to 12-17
single images, printing, 12-4 to 12-9
starting, 12-3
Diskettes, copying pictures, 8-13 to 8-14
Display panel
messages, 12-17 to 12-18
reading, 2-2 to 2-4
Distorting images, 9-7 to 9-9
Documents, getting pictures into, 7-1 to 7-8, 13-6
Downloading pictures, 6-1 to 6-14, 7-6 to 7-8
Drag and drop, 7-4 to 7-6, 7-7 to 7-8
E
Edges, sharpening, 9-8
Editing
applying Quick Fix to images, 9-3
images, 9-2 to 9-9
sounds, 8-10
E-mail, sending pictures, 8-14 to 8-16
Environmental specifications, B-3
EPSON
Electronic support services, Intro-6 to Intro-7
help, Intro-6 to Intro-7
registration, Intro-7
World Wide Web site, Intro-6
EPSON Photo File Uploader, 11-1 to 11-12
EPSON Photo!3
importing images, 6-10 to 6-14
problems, 6-14 to 6-15
support, Intro-7
using, 6-12 to 6-15
Equalization, 9-4
Erasing pictures from camera
using computer, 6-8, 6-11, 6-13, 7-7
using LCD screen, 5-4 to 5-6
Error messages
on camera display panel, 12-17 to 12-18
on computer, 6-9 to 6-10, 6-14, 13-4
Exporting images, 6-12 to 6-13
Exposure
adjusting, 3-7 to 3-8, 4-24
predefined settings, 4-22 to 4-23
A
B
Index 3
Altair.book Page 4 Thursday, July 1, 1999 3:33 PM
F
H
FaxAdvice service, Intro-6
Features, camera, Intro-1 to Intro-3
Files
BMP, 6-13
converting during transfer, 6-12 to 6-14
JPEG, 6-12 to 6-13, 7-2
PCX, 6-13
PICT, 6-13
resizing, 9-5 to 9-6
uploading, 11-1 to 11-7
viewing information, 8-3 to 8-4
Fisheye effect, 9-8
Flash
problems, 13-3
range, B-4
using, 3-3 to 3-4
Flipping images, 9-7
Focus, adjusting, 4-24 to 4-25
Formatting the memory card, 1-12 to 1-13
FTP, Intro-6
Full Auto mode, description, 4-3
Handling batteries, 1-8 to 1-9
Help, EPSON, Intro-6 to Intro-7
HyPict image quality, 3-2
G
Glass blocks effect, 9-8
4 Index
I
Image Authentication System, Intro-4
Image Expert
albums, 7-4 to 7-6, 8-2 to 8-14
audio tools, 8-9
camera settings, changing, 10-5 to 10-7
Camio Viewer, 7-6 to 7-8
color correcting, 9-3 to 9-4
color depth, changing, 9-9
copying pictures to diskette, 8-13 to 8-14
correcting images, 9-3 to 9-4
cropping, 9-5
editing pictures, 9-1 to 9-9
e-mailing pictures, 8-14 to 8-16
error messages, 6-9 to 6-10
flipping images, 9-7
picture information, 8-3 to 8-4
printing, 8-4 to 8-8
Quick Fix, 9-3
resizing images, 9-5 to 9-6
Altair.book Page 5 Thursday, July 1, 1999 3:33 PM
Image Expert (Continued)
resolution, changing, 9-5 to 9-6
rotating, 9-6 to 9-7
screen saver, 8-12
selection tools, 9-2
slide shows, 8-11 to 8-12
sound, adding, 8-8 to 8-9
sound, deleting, 8-10 to 8-11
sound, editing, 8-10
special effects, 9-7 to 9-9
taking pictures from computer, 10-1 to 10-3
transferring pictures, 6-5 to 6-10, 7-6 to 7-8
wallpaper, 8-12
zoom tool, 9-2
Image quality, setting, 3-1 to 3-2, B-2
Images, see Pictures
Importing photos, TWAIN programs, 6-10 to 6-11
Index, printing, 12-15 to 12-16
Installing
batteries, 1-6 to 1-7
Direct Print in camera, 12-17
memory card, 1-10 to 1-11
PCMCIA adapter, A-4 to A-5
software, 1-14 to 1-16
Internet, Intro-6
Interval shooting, 4-12 to 4-13
Inverting images, 9-7
IOMEGA Clik! drive, A-6
J
JPEG files, 6-12 to 6-13, 7-2
L
Landscape subject setting, 4-15
Language, setting, 4-30
LCD screen
erasing pictures, 5-4 to 5-6
magnifying pictures, 5-11 to 5-12
playing back pictures, 5-1 to 5-19
problems, 13-3 to 13-4
setting brightness, 4-28
specifications, B-3
Licensing software, Intro-7
Live preview, 10-1 to 10-5
M
Macintosh
capturing screens, 11-9 to 11-10
connecting to camera, 6-1 to 6-5
installing software, 1-16
system requirements, Intro-5
uploading pictures, 11-5 to 11-9
A
B
Index 5
Altair.book Page 6 Thursday, July 1, 1999 3:33 PM
Macro mode, using, 4-7 to 4-8
Magnifying pictures, 5-11 to 5-12
Maintenance, 13-1 to 13-2
Manual mode, description, 4-3
Memory card
capacity, B-4
dimensions, B-5
formatting, 1-12 to 1-13, 13-7
installing, 1-10 to 1-11
removing, 1-13
uploading images to, 11-1 to 11-7
Metering method, changing, 4-25 to 4-26
Monochrome pictures, taking, 4-4
N
Negative images, 9-8
NiMH Power Pak, ordering, Intro-4
O
Options
AC adapter, specifications, B-5
AC adapter, using, A-2 to A-3
IOMEGA Clik! drive, A-6
ordering, A-2
PCMCIA adapter, using, A-4 to A-5
tripod, using, A-4
6 Index
P
Panoramic pictures, 4-8 to 4-9
PCMCIA adapter, using, A-4 to A-5
PCX files, 6-13
Photo File Uploader, 11-1 to 11-12
Photo stickers, printing, 12-13 to 12-14
Photographic specifications, B-3
Photos, see Pictures
Physical dimensions, B-1
PICT files, 6-13
Picture counter, checking, 2-3 to 2-4
Pictures
black and white, 4-4
capturing from computer, 10-1 to 10-5
close-ups, 4-7 to 4-8
color correcting, 9-3 to 9-4
color depth, changing, 9-9
converting, 7-2
copying to diskette, 8-13 to 8-14
correcting, 9-2 to 9-4
cropping, 9-5
e-mailing, 8-14 to 8-16
erasing with camera, 5-4 to 5-6
erasing with computer, 6-8, 6-11, 6-13, 7-7
exporting, 6-12 to 6-13
Altair.book Page 7 Thursday, July 1, 1999 3:33 PM
Pictures (Continued)
flipping, 9-7
macro mode, 4-7 to 4-8
magnifying, 5-11 to 5-12
organizing in albums, 8-2 to 8-3
panoramic, 4-8 to 4-9
playing back on TV, 5-17 to 5-19
printing from camera, 12-4 to 12-16
printing from computer, 8-4 to 8-8
problems, solving, 13-8 to 13-11
quick shots, 4-4 to 4-5
resizing, 9-5 to 9-6
rotating, 9-6 to 9-7
screen saver, 8-12
selecting sections, 9-2 to 9-4
slide shows, 5-13 to 5-16, 8-11 to 8-12
special effects, 9-8 to 9-9
transferring from camera, 6-1 to 6-14, 7-6 to 7-8
uploading, 11-1 to 11-7
using digital zoom, 4-5 to 4-6
viewing information, 8-3 to 8-4
wallpaper, 8-12
Playing back pictures, 5-1 to 5-19
Portrait subject setting, 4-15
Power
AC adapter, 2-3, A-2 to A-3, B-5
battery, see Batteries
camera specifications, B-1
problems, 13-2
Power off interval, setting, 4-26 to 4-27
Power Pak, ordering, Intro-4
Presentations, using camera for, 11-1 to 11-12
Printing photos from camera
album format, 12-11 to 12-12
cards, 12-10 to 12-11
index of images, 12-15 to 12-16
photo stickers, 12-13 to 12-14
print formats, 12-4
single images, 12-4 to 12-9
Printing photos from computer
adding text, 8-6
adjusting printed area, 8-7 to 8-8
choosing album images, 8-7
layout styles, 8-4 to 8-6
A
B
Index 7
Altair.book Page 8 Thursday, July 1, 1999 3:33 PM
Problems
camera, 6-14 to 6-15, 13-2 to 13-7
Direct Print, 12-17 to 12-18
EPSON Photo!3, 6-14 to 6-15
flash, 13-3
LCD screen, 13-3 to 13-4
memory card, 13-7
picture, 13-8 to 13-11
Program mode
description, 4-3
using programmed subject settings, 4-15 to 4-16
Projector, playing back pictures and presentations,
11-11 to 11-12
Q
Quick Fix, 9-3
Quick shots, taking, 4-4 to 4-5
R
RAM, system requirements, Intro-4 to Intro-5
Registration, Intro-7
Removing Direct Print from camera, 12-16 to 12-17
Resizing files, 9-5 to 9-6
Resolution, 3-1 to 3-2, 9-5 to 9-6, B-2
Ripples effect, 9-8
Rotating pictures, 9-6 to 9-7
8 Index
S
Safety instructions, Intro-8 to Intro-9
Save to Floppy option, 8-13 to 8-14
Screen captures, 11-8 to 11-10
Self timer, using, 3-4 to 3-5, 10-3 to 10-5
Sending pictures by e-mail, 8-14 to 8-16
Sensitivity, adjusting, 3-5 to 3-6, 4-17 to 4-18
Serial cable, connecting, 6-3 to 6-5
Settings
adjusting, 3-1 to 3-8, 4-1 to 4-30
alert beep, 4-28 to 4-29
automatic power off, 4-26 to 4-27
color/black and white, 4-4
date and time, 1-11 to 1-12, 4-29 to 4-30
exposure, 3-7 to 3-8, 4-24
focus, 4-24 to 4-25
image quality, 3-1 to 3-2, B-2
language, 4-30
LCD brightness, 4-28
macro mode, 4-7 to 4-8
metering method, 4-25 to 4-26
panoramic pictures, 4-8 to 4-9
predefined exposure adjustments, 4-22 to 4-23
programmed subject settings, 4-15 to 4-16
sensitivity, 3-5 to 3-6, 4-17 to 4-18
Altair.book Page 9 Thursday, July 1, 1999 3:33 PM
Settings (Continued)
shutter speed and aperture, 4-24
time and date, 1-11 to 1-12, 4-29 to 4-30
user mode, 4-2 to 4-3
white balance, 3-6 to 3-7, 4-18 to 4-22
Sharpness, adjusting, 9-4
Shutter
adjusting speed, 4-24
predefined exposure adjustments, 4-22 to 4-23
snapping, 2-4 to 2-6
Slide shows
excluding pictures, 5-14 to 5-15
playing pictures, 5-13 to 5-16, 8-11 to 8-12
rotating pictures, 5-15 to 5-16
Slow synchronized flash, 3-3
Software
included on CD-ROM, Intro-3
installing, 1-14 to 1-16
licensing, Intro-7
support, Intro-7
Sound
adding, 4-13 to 4-15, 8-8 to 8-9
deleting, 5-10 to 5-11, 8-10 to 8-11
editing, 8-10
playing back, 8-9
recording, 8-8 to 8-9
SoundAdvice, Intro-6
Special effects, 9-8 to 9-9
Specifications
AC adapter, B-5
battery charger, B-5
environmental, B-3
memory card, B-4, B-5
photographic, B-3
physical dimensions, B-1
power, B-1
safety, B-3
technical, B-2
Sports subject setting, 4-15
Status display panel
messages, 12-17 to 12-18
reading, 2-2 to 2-4
Stickers, printing, 12-13 to 12-14
Storage cards, see Memory cards
Storing camera, 13-2
Strap, attaching, 1-9
Support
EPSON, Intro-6 to Intro-7
software, Intro-7
System requirements
Macintosh, Intro-5
Windows, Intro-4
A
B
Index 9
Altair.book Page 10 Thursday, July 1, 1999 3:33 PM
T
Taking pictures
using the flash, 3-3 to 3-4
with the LCD screen, 2-6 to 2-9
with the timer, 3-4 to 3-5
with the viewfinder, 2-4 to 2-6
Technical support, Intro-6 to Intro-7
Time and date, setting, 1-11 to 1-12, 4-29 to 4-30
Timer, using, 3-4 to 3-5, 4-11 to 4-12, 10-3 to 10-5
Tripod, attaching, A-4
Troubleshooting, 13-2 to 13-11
TWAIN programs, acquiring photos, 6-10 to 6-11
U
Unpacking the camera, 1-1
Uploading pictures, 11-1 to 11-7
USB cable, connecting, 6-2
User mode, setting, 4-2 to 4-3
V
VCR, playing back pictures, 5-17 to 5-19
Video cable, 11-11
Videotaping pictures, 5-17 to 5-19
10 Index
Voice recordings
adding, 4-13 to 4-15, 8-8 to 8-9
deleting, 5-10 to 5-11, 8-10 to 8-11
editing, 8-10
playing back, 8-9 to 8-10
W
Wallpaper, setting pictures as, 8-12 to 8-13
White balance
adjusting, 3-6 to 3-7, 4-18 to 4-22
fixed, 4-19 to 4-20
user-defined setting, 4-21 to 4-22
Windows
capturing screens, 11-8 to 11-9
connecting with serial cable, 6-3 to 6-4
connecting with USB cable, 6-2
installing software, 1-14 to 1-16
system requirements, Intro-4
uploading pictures, 11-2 to 11-4
World Wide Web, Intro-6
Wrist strap, attaching, 1-9
Z
Zoom tool, Image Expert, 9-2
Zoom, using digital zoom, 4-5 to 4-6

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project