TwisTorr 84 FS AG Rack Controller User Manual

TwisTorr 84 FS AG Rack Controller User Manual
TwisTorr 84 FS AG
Rack Controller
Models
X3508 64001, X3508 64002
Manuale di istruzioni
Bedienungshandbuch
Notice de mode d’emploi
Manual de istrucciones
Manual de istruções
Bedrijfshandleiding
Istrukstionsbog
Bruksanvisning
87-901-037-01 (A)
11/2014
Instruksjon manual
Ohjekäsikirja
Felhasználói kézikönyv
Podrecznik instrukcji
N
Návod na obsluhu
P
User Manual
Warranty
Notices
© Agilent Technologies, Inc. 2014
No part of this manual may be
reproduced in any form or by any
means (including electronic storage
and retrieval or translation into a
foreign language) without prior
agreement and written consent from
Agilent Technologies, Inc. as governed
by United States and international
copyright laws.
Manual Part Number
Publication Number: 87-901-037-01 (A)
Edition
Edition 11/2014
Printed in ITALY
Agilent Technologies Italia S.p.A.
Vacuum Products Division
Via F.lli Varian, 54
10040 Leinì (TO)
ITALY
The material contained in this
document is provided “as is,” and is
subject to being changed, without
notice, in future editions. Further, to
the maximum extent permitted by
applicable law, Agilent disclaims all
warranties, either express or implied,
with regard to this manual and any
information contained herein,
including but not limited to the
implied warranties of merchantability
and fitness for a particular purpose.
Agilent shall not be liable for errors
or for incidental or consequential
damages in connection with the
furnishing, use, or performance of
this document or of any information
contained herein. Should Agilent and
the user have a separate written
agreement with warranty terms
covering the material in this
document that conflict with these
terms, the warranty terms in the
separate agreement shall control.
Technology Licenses
The hardware and/or software
described in this document are
furnished under a license and may be
used or copied only in accordance
with the terms of such license.
Restricted Rights Legend
If software is for use in the
performance of a U.S. Government
prime contract or subcontract,
Software is delivered and licensed as
“Commercial computer software” as
defined in DFAR 252.227-7014 (June
1995), or as a “commercial item” as
defined in FAR 2.101(a) or as
“Restricted computer software” as
defined in FAR 52.227-19 (June 1987)
or any equivalent agency regulation or
contract clause. Use, duplication or
disclosure of Software is subject to
Agilent Technologies’ standard
commercial license terms, and nonDOD Departments and Agencies of the
U.S. Government will receive no
greater than Restricted Rights as
defined in FAR 52.227-19(c)(1-2) (June
1987). U.S. Government users will
receive no greater than Limited Rights
as defined in FAR 52.227-14 (June
1987) or DFAR 252.227-7015 (b)(2)
(November 1995), as applicable in any
technical data.
Trademarks
Windows and MS Windows are U.S.
registered trademarks of Microsoft
Corporation.
Safety Notices
CAUTION
A CAUTION notice denotes a hazard.
It calls attention to an operating
procedure, practice, or the like that, if
not correctly performed or adhered to,
could result in damage to the product
or loss of important data. Do not
proceed beyond a CAUTION notice
until the indicated conditions are fully
understood and met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or the
like that, if not correctly performed
or adhered to, could result in
personal injury or death. Do not
proceed beyond a WARNING notice
until the indicated conditions are
fully understood and met.
TwisTorr 84 FS AG Rack ControllerUser Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller
TwisTorr 84 FS AG Rack Controller
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
3/297
TwisTorr 84 FS AG Rack Controller
4/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Contents
Contents
1
Istruzioni per l’uso 15
Informazioni Generali
16
Immagazzinamento 17
Preparazione per l’installazione 18
Installazione
19
Uso 20
Procedure di uso
23
Manutenzione 23
Smaltimento
24
Messaggi di errore 25
2
Gebrauchsanleitung 27
Allgemeines 28
Lagerung
29
Vor der Installation 30
Installation 31
Gebrauch
32
Bedienung 35
Wartung
35
Entsorgung 36
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
5/297
Contents
3
Fehlermeldungen
37
Mode d’emploi
39
Indications generales
40
Emmagasinage 41
Preparation pour l‘installation
42
Installation 43
Utilisation 44
Procedures d'utilisation 47
Entretien
47
Mise au rebut
48
Messages d'erreur 49
4
Manual de istrucciones 51
Información general 52
Almacenamiento
53
Preparación para la instalación 54
Instalación 55
Uso 56
Procedimientos de uso 59
Mantenimiento 59
Eliminación 60
Mensajes de error
6/297
61
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Contents
5
Manual de Istruções
63
Informações gerais 64
Armazenagem 65
Preparação para a instalação 66
Instalação 67
Utilização
68
Procedimentos de uso
Manutenção
71
71
Eliminação 72
Mensagens de erro 73
6
Bedrijfshandleiding 75
Algemene informatie
Opslag
76
77
Voorbereiding voor installatie
Installatie
79
Gebruik
80
78
Gebruiksprocedures 83
Onderhoud 83
Afvalverwerking 84
Foutmeldingen 85
7
Istruktionsbog
87
Generel Information 88
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
7/297
Contents
Opbevaring 89
Forberedelser før installation 90
Installation 91
Anvendelse 92
Instruktion 95
Vedligeholdelse 95
Bortskaffelse
96
Fejlmeddelelser 97
8
Bruksanvisning
99
Allmän Information 100
Förvaring
101
Förberedelser för installation 102
Installation 103
Användning 104
Instruktioner för bruk
Underhåll
107
107
Bortskaffning
108
Felmeddelanden 109
9
Instruksjon Manual 111
Generell informasjon112
Lagring
113
Forberede installasjonen 114
8/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Contents
Installasjon 115
Bruk
116
Instruksjoner for bruk
119
Vedlikehold 119
Eliminering 120
Feilmeldinger
121
10 Ohjekäsikirja
Yleisiä tietoja
123
124
Varastointi 125
Valmistelut asennusta varten126
Asennus
127
Käyttö
128
Käyttötoimenpiteet 131
Huolto
131
Hävittäminen
132
Vianetsintä 133
11 Felhasználói Kézikönyv 135
Általános információk
Tárolás
136
137
138
Telepítés
139
Használat
140
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
9/297
Contents
Használati eljárások 143
Karbantartás
143
Megsemmisítés 144
Hibaüzenetek
145
12 Podrecznik Instrukcji
Informacje ogolne
147
148
Magazynowanie 149
Przygotowanie do instalacji 150
Instalacja
151
Uzytkowanie
152
Procedure uzytkowania 155
Konserwacja
155
Przetworstwo odpadow 156
Bledne informacje
157
159
13
Všeobecné informace
160
ní 161
162
Instalace
163
164
167
167
10/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Contents
Likvidace
168
Chybné zprávy 169
14 Návod na Obsluhu 171
Všeobecné informácie
Usklad
173
Príprava pre inštaláciu
Inštalácia
172
174
175
176
179
179
Likvidácia
180
Oznamy vád 181
183
15
Splošne informacije 184
185
186
187
Uporaba
188
Postopki uporabe
191
191
Odlaganje opadkov 192
Obvestilo o napaki 193
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
11/297
Contents
16 Instructions for Use 195
General Information 196
Storage
197
Preparation for Installation 198
Installation 199
Use 200
Use Procedure 203
Maintenance
Disposal
203
204
Error Messages 205
17 Technical Information
207
TwisTorr 84 Rack Controller Description 209
Controller Specifications 211
Controller Outline
212
Controller Connection
213
R1 – R2 Output Diagrams
220
Programmable Analog Output Diagrams 222
J2 – Serial Connector
227
Letter Protocol Description 230
Examples
239
How to Use by Front Panel 247
Use 252
12/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Contents
Programming
258
How to Use by Remote I/0 271
How to Use in Serial Mode 271
Profibus Option 273
Error Messages 288
Orderable Parts 291
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
13/297
Contents
14/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
1
Istruzioni per l’uso
Informazioni Generali 16
Immagazzinamento
17
Preparazione per l’installazione 18
Installazione
Uso
18
20
Comandi, Indicatori e Connettori 21
Descrizione pannello frontale
21
Procedure di uso 21
Accensione del Controller
23
Avvio della Pompa 23
Arresto della Pompa
Manutenzione
23
Smaltimento
23
Messaggi di errore
23
25
Traduzione delle istruzioni originali
15/297
1
Istruzioni per l’uso
Informazioni Generali
Informazioni Generali
Questa apparecchiatura è destinata ad uso professionale.
L'utilizzatore deve leggere attentamente il presente manuale di
istruzioni ed ogni altra informazione addizionale fornita dalla Agilent
prima dell'utilizzo dell'apparecchiatura. La Agilent si ritiene sollevata
da eventuali responsabilità dovute all'inosservanza totale o parziale
delle istruzioni, ad uso improprio da parte di personale non
addestrato, ad interventi non autorizzati o ad uso contrario alle
normative nazionali specifiche. I controller della serie TwisTorr 84
Rack sono dei convertitori di frequenza, controllati da un
microprocessore, realizzati con componenti a stato solido e con
capacità di autodiagnostica e autoprotezione.
Caratteristiche del controller:
Operatività frontale / remota / seriale
Pilotaggio a 24 Vdc della ventola di raffreddamento pompa
Pilotaggio vent valve
Lettura velocità pompa in seguito al commando di arresto
(lettura velocità di arresto)
Lettura della pressione
Interfaccia Profibus (opzionale)
Impostazione automatica tensione di ingresso.
Nei paragrafi seguenti sono riportate tutte le informazioni necessarie
a garantire la sicurezza dell'operatore durante l'utilizzo
dell'apparecchiatura. Informazioni dettagliate sono fornite
nell'appendice "Technical Information".
16/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruzioni per l’uso
Immagazzinamento
1
Questo manuale utilizza le seguenti convenzioni:
AVVERTENZA! I messaggi di avvertenza attirano l’attenzione dell’operatore su una
procedura o una pratica specifica che, se non eseguita in modo corretto,
potrebbe provocare gravi lesioni personali.
ATTENZIONE! I messaggi di attenzione sono visualizzati prima di procedure che, se non
osservate, potrebbero causare danni all’apparecchiatura.
NOTA
Le note contengono informazioni importanti estrapolate dal testo.
Immagazzinamento
Durante il trasporto e l’immagazzinamento dei controller devono
essere soddisfatte le seguenti condizioni ambientali:
temperatura: da -20 °C a +70 °C
umidità relativa: 0 – 95 % (non condensante)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
17/297
1
Istruzioni per l’uso
Preparazione per l’installazione
Preparazione per l’installazione
Il controller viene fornito in un imballo protettivo speciale; se si
presentano segni di danni, che potrebbero essersi verificati durante il
trasporto, contattare l'ufficio vendite locale.
Durante l'operazione di disimballaggio, prestare particolare
attenzione a non lasciar cadere il controller e a non sottoporlo ad
urti.
Non disperdere l'imballo nell'ambiente. Il materiale è completamente
riciclabile e risponde alla direttiva CEE 85/399 per la tutela
dell'ambiente.
Figura 1
18/297
Imballo dei controller
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruzioni per l’uso
Installazione
1
Installazione
AVVERTENZA! Il controller è progettato solo per uso interno e deve essere alimentato
mediante un cavo di alimentazione a tre fili (vedere tabella delle parti
ordinabili) con una spina di tipo approvato a livello internazionale ai fini della
sicurezza dell’utente. Utilizzare sempre questo cavo di alimentazione ed
inserire la spina in una presa con un adeguato collegamento di terra onde
evitare scariche elettriche e per rispettare le specifiche CE. All'interno del
controller si sviluppano alte tensioni che possono recare gravi danni o la
morte. Prima di eseguire qualsiasi operazione di installazione o manutenzione
del controller scollegarlo dalla presa di alimentazione.
NOTA
II controller può essere installato su di un tavolo o all’interno di un apposito rack.
In ogni caso occorre che l’aria di raffreddamento possa circolare liberamente
intorno all'apparato. Non installare né utilizzare il controller in ambienti esposti ad
agenti atmosferici (pioggia, gelo, neve), polveri, gas aggressivi, in ambienti
esplosivi o con elevato rischio di incendio.
Durante il funzionamento è necessario che siano rispettate le
seguenti condizioni ambientali:
temperatura: da 5 °C a +45 °C;
umidità relativa: 0 – 95 % (non condensante).
Per gli altri collegamenti e I'installazione degli accessori opzionali,
vedere la sezione "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
19/297
1
Istruzioni per l’uso
Uso
Uso
In questo paragrafo sono riportate le principali procedure operative.
Per ulteriori dettagli e per procedure che coinvolgono collegamenti o
particolari opzionali, fare riferimento al paragrafo "Use"
dell'appendice "Technical Information".
Prima di usare il controller effettuare tutti i collegamenti elettrici e
pneumatici e fare riferimento al manuale della pompa collegata.
AVVERTENZA! Per evitare danni alle persone ed all'apparato, nel caso in cui la pompa sia
appoggiata su di un tavolo assicurarsi che sia stabile. Non fare funzionare
mai la pompa se la flangia di ingresso non è collegata al sistema o non è
chiusa con la flangia di chiusura.
NOTA
20/297
Il connettore di richiusura J1 deve essere lasciato collegato con il suo ponticello
se non viene effettuato alcun collegamento esterno. La pompa di pre-vuoto e la
pompa TwisTorr possono essere accese contemporaneamente.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruzioni per l’uso
Uso
1
Comandi, Indicatori e Connettori
Di seguito sono illustrati il pannello di comando del Controller ed i
pannelli di interconnessione. Per maggiori dettagli fare riferimento
alla sezione "Technical Information".
Descrizione pannello frontale
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
Turbo-V
TwisTorr
84301-AG
FS AG
Figura 2
Pannello frontale del Controller TwisTorr 84-AG
1
Pulsante per richiamare sul display i parametri cycle number, cycle time e pump life.
2
Pulsante per la selezione del modo LOW SPEED. È attivo solo quando è selezionato il
modo di comando dal pannello frontale. Premendolo una volta, la pompa ruota a velocità
“stand-by”. Premendolo ancora si disattiva il modo LOW SPEED.
3
Pulsante per richiamare sul display i parametri pump current, pump temperature, pump
power e rotational speed. È sempre attivo indipendentemente dal modo di
funzionamento scelto. Premendo assieme i pulsanti 3 e 1 per almeno 2 secondi viene
attivato un programma con il quale è possibile programmare alcuni parametri operativi.
4
Pulsante per inviare i comandi di START, STOP/RESET. È attivo solo quando è
selezionato il modo di comando dal pannello frontale. Premendolo una volta si attiva la
fase di avvio; premendolo nuovamente si arresta la pompa. Se la pompa si è fermata
automaticamente a causa di un guasto, occorre premere questo pulsante una prima
volta per eseguire il reset del controller ed una seconda volta per riavviare la pompa.
5
Display alfanumerico a cristalli liquidi: matrice di punti, 2 linee x 16 caratteri.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
21/297
1
Istruzioni per l’uso
Uso
8
7
6
1
2
5
3
Figura 3
4
Pannello posteriore dei Controller TwisTorr84-AG
1
Connettore di ingresso dei segnali logici (il connettore di accoppiamento viene fornito con
l’apposito ponticello di richiusura).
2
Connettore segnali logici in uscita e monitoraggio frequenza pompa più uscita analogica
programmabile.
3
Connettore di uscita alimentazione (24 Vdc per la ventola di raffreddamento pompa, vent
valve e calibro).
4
Modulo di ingresso alimentazione controller che comprende i fusibili, la presa di
alimentazione ed il filtro ENC.
5
Switch a rotazione per impostare l’indirizzo del Profibus.
6
Profibus (opzionale).
7
Connettore seriale per controllo da remoto.
8
Pompa.
22/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruzioni per l’uso
Procedure di uso
1
Procedure di uso
Accensione del Controller
Per accendere il controller è sufficiente inserire il cavo di
alimentazione nella presa di rete.
Avvio della Pompa
Per avviare la pompa occorre abilitare l’ingresso di interlock e
premere il pulsante START del pannello frontale.
Arresto della Pompa
Per arrestare la pompa occorre premere il pulsante STOP del
pannello frontale.
Manutenzione
I controller della serie TwisTorr 84 Rack non richiedono alcuna
manutenzione. Qualsiasi intervento deve essere eseguito da
personale autorizzato. In caso di guasto è possibile usufruire del
servizio di riparazione Agilent o del "Agilent advanced exchange
service", che permette di ottenere un controller rigenerato in
sostituzione di quello guasto.
AVVERTENZA! Prima di effettuare qualsiasi intervento sul controller scollegare il cavo di
alimentazione.
Qualora un controller dovesse essere rottamato, procedere alla sua
eliminazione nel rispetto delle normative nazionali specifiche.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
23/297
1
Istruzioni per l’uso
Smaltimento
Smaltimento
Significato del logo "WEEE" presente sulle etichette. Il simbolo qui
sotto riportato è applicato in ottemperanza alla direttiva CE
denominata "WEEE". Questo simbolo (valido solo per i paesi della
Comunità Europea) indica che il prodotto sul quale è applicato, NON
deve essere smaltito insieme ai comuni rifiuti domestici o industriali,
ma deve essere avviato ad un sistema di raccolta differenziata. Si
invita pertanto l'utente finale a contattare il fornitore del dispositivo,
sia esso la casa madre o un rivenditore, per avviare il processo di
raccolta e smaltimento, dopo opportuna verifica dei termini e
condizioni contrattuali di vendita.
24/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruzioni per l’uso
Messaggi di errore
1
Messaggi di errore
In alcuni casi di guasto la circuiteria di autodiagnosi del controller
presenta alcuni messaggi di errore elencati nella tabella seguente.
Tab. 1
MESSAGGIO
DESCRIZIONE
AZIONE CORRETTIVA
CHECK
CONNECTION
TO PUMP
Malfunzionamento nel
collegamento tra pompa e
controller.
Verificare che il cavo di
collegamento tra pompa e
controller sia ben fissato da
entrambe le estremità e non
sia interrotto. Premere due
volte il pulsante START per
riavviare la pompa.
Oppure
La pompa ha una temperatura
inferiore a 0 °C.
WAITING
INTERLOCK
È attivo il segnale di interlock
presente sul connettore P1 a causa
dell'interruzione del corto circuito
tra il pin 3 ed il pin 8 del connettore
J1, o a causa dell'apertura del
segnale di interlock esterno.
Ripristinare il corto circuito
tra il pin 3 ed il pin8 del
connettore P1, o chiudere il
segnale di interlock esterno.
PUMP
OVERTEMP.
La temperatura del cuscinetto
superiore o della pompa ha
superato i 60 °C.
Attendere che la
temperatura ritorni al di
sotto della soglia. Premere
due volte il pulsante START
per riavviare la pompa.
CONTROLLER
OVERTEMP.
La temperatura dell’ambiente del
controller ha superato i 70 °C.
Attendere che la
temperatura ritorni al di
sotto della soglia. Premere
due volte il pulsante START
per riavviare la pompa.
Oppure.
La temperatura del radiatore del
controller è superiore a 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
25/297
1
Istruzioni per l’uso
Messaggi di errore
26/297
MESSAGGIO
DESCRIZIONE
AZIONE CORRETTIVA
TOO HIGH
L0AD
La corrente assorbita dalla pompa è
maggiore di quella programmata.
Verificare che il rotore della
pompa abbia la possibilità di
ruotare liberamente.
Premere due volte il pulsante
START per riavviare la
pompa.
SHORT
CIRCUIT
Durante il funzionamento normale
(dopo la fase di avvio) la
connessione di uscita è in corto
circuito.
Verificare i collegamenti tra
pompa e controller. Premere
due volte il pulsante START
per riavviare la pompa.
SYSTEM
OVERRIDE
La pompa è stata fermata da un
segnale di emergenza proveniente
da un contatto remoto.
Staccare il cavo di
alimentazione del controller
e correggere la causa
dell'emergenza. Ricollegare il
cavo di alimentazione e
premere due volte il pulsante
START per riavviare la
pompa.
OVERVOLTAGE
Si è verificato un guasto nella
sezione di alimentazione del
controller, o il controller ha ricevuto
un segnale spurio.
Premere due volte il pulsante
START per riavviare la
pompa. Se il messaggio si
ripresenta rivolgersi in
Agilent per la manutenzione.
POWER FAIL
Guasto nella sezione di
alimentazione della pompa, del
controller.
Rivolgersi alla Agilent per
Manutenzione.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
2
Gebrauchsanleitung
Allgemeines
28
Lagerung
29
Vor der Installation
Installation
31
Gebrauch
32
30
Steuerungen, Anzeigen und Verbinder des Controllers 32
Fronttafel der Controller
Bedienung
33
35
Einschalten des Controllers 35
Pumpenstart 35
Pumpenstopp 35
Wartung
35
Entsorgung
36
Fehlermeldungen 37
Übersetzung der Originalanleitungen
27/297
2
Gebrauchsanleitung
Allgemeines
Allgemeines
Dieser Apparat ist für Fachbetriebe bestimmt. Vor Gebrauch sollte der
Benutzer dieses Handbuch sowie alle weiteren mitgelieferten
Zusatzdokumentationen genau lesen. Bei Nichtbeachtung - auch
teilweise - der enthaltenen Hinweise, unsachgemäßem Gebrauch durch
ungeschultes Personal, nicht autorisierten Eingriffen und Mißachtung
der einheimischen, hier zur Geltung kommenden Bestimmungen
übernimmt die Firma Agilent keinerlei Haftung.
Die Controller der Serie TwisTorr 84 Rack sind
mikroprozessorgesteuerte Frequenzwandler. Sie sind mit
Festkörperbauteilen gefertigt und verfügen über ein Selbstdiagnose- und
ein Selbstschutzsystem.
Controllereigenschaften:
Konsol-, Fern- und serielle Operationen
24V= Kühlventilator-Treiber
Vent Valve Treiber
Auslesen der Pumpgeschwindigkeit nach Stoppbefehl (Lesen der
Stoppgeschwindigkeit)
Auslesen des Drucks
Profibus-Schnittstelle (Option)
automatische Einstellung der Eingangsspannung
In den folgenden Abschnitten sind alle erforderlichen Informationen für
die Sicherheit des Bedieners bei der Anwendung des Geräts aufgeführt.
Detaillierte technische Informationen sind im Anhang "Technical
Information" enthalten.
28/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Gebrauchsanleitung
Lagerung
2
In dieser Gebrauchsanleitung werden Sicherheitshinweise
folgendermaßen hervorgehoben:
WARNUNG!
Die Warnhinweise lenken die Aufmerksamkeit des Bedieners auf eine
bestimmte Prozedur oder Praktik, die bei unkorrekter Ausführung schwere
Verletzungen hervorrufen können.
VORSICHT!
Die Vorsichtshinweise vor bestimmten Prozeduren machen den Bediener darauf
aufmerksam, daß bei Nichteinhaltung Schäden an der Anlage entstehen können.
HINWEIS
Die Hinweise enthalten wichtige Informationen, die aus dem Text hervorgehoben
werden.
Lagerung
Beim Transport und bei der Lagerung der Controller müssen
folgende klimatische Verhältnisse eingehalten werden:
Temperatur: von -20 °C bis +70 °C
Relative Luftfeuchtigkeit: 0 – 95 % (nicht kondensierend)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
29/297
2
Gebrauchsanleitung
Vor der Installation
Vor der Installation
Der Controller wird mit einer speziellen Schutzverpackung geliefert.
Eventuelle Transportschäden müssen der zuständigen örtlichen
Verkaufsstelle gemeldet werden.
Beim Auspacken vorsichtig vorgehen, damit der Controller nicht fällt
oder Stößen ausgesetzt wird.
Das Verpackungsmaterial muß korrekt entsorgt werden. Es ist
vollständig recyclebar und entspricht der EG-Richtlinie 85/399 für
Umweltschutz.
Abbildung 1
30/297
Verpackung der Controller
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Gebrauchsanleitung
Installation
2
Installation
WARNUNG!
HINWEIS
Der TwisTorr Controller muss mit einem dreiadrigen Netzkabel und dem
(international zugelassenen) Stecker angeschlossen werden. Es sollte
immer dieses Netzkabel benutzt werden, das an eine korrekt geerdete
Steckdose anzuschließen ist, um den CE Richtlinien zu entsprechen und
Stromschläge zu vermeiden. Im Inneren des Controllers entstehen hohe
Spannungen, die schwere Verletzungen verursachen und lebensgefährlich
sein können. Vor jedem Montage- bzw. Wartungseingriff muss deshalb der
Netzstecker gezogen werden.
Der Controller kann auf einen Tisch oder ein Gestell montiert werden. In beiden
Fällen muß auf die ungehinderte Zirkulation der Kühlluft im Bereich des Geräts
geachtet werden. Der Controller darf nicht in Umgebungen installiert u/o
benutzt werden, die Witterungseinflüssen (Regen, Frost, Schnee), Staub und
aggressiven Gasen ausgesetzt sind und in denen Explosions- und erhöhte
Brandgefahr besteht.
Beim Betrieb müssen folgende Umgebungsbedingungen eingehalten
werden:
Temperatur: von +5 °C bis +45 °C
Relative Luftfeuchtigkeit: 0 – 95 % (nicht kondensierend).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
31/297
2
Gebrauchsanleitung
Gebrauch
Gebrauch
In diesem Kapitel sind die wichtigsten Betriebsvorgänge aufgeführt.
Für weitere Hinweise bezüglich Anschlüsse und Montage des
bestellbaren Zubehörs siehe Kapitel "Use" im Anhang zu "Technical
Information".
Vor Benutzung des Controllers sämtliche elektrischen und
pneumatischen Anschlüsse ausführen, und die Betriebsanleitung der
angeschlossenen Pumpe durchlesen.
WARNUNG!
Steht die Pumpe auf einem Tisch, muß auf den stabilen Stand geachtet
werden, da sonst die Gefahr von Personen- und Geräteschäden besteht. Die
Pumpe nie einschalten, wenn der Eingangsflansch nicht am System
angeschlossen bzw. nicht mit dem Schließflansch abgedeckt ist.
HINWEIS
Der Wiederverschließ-Verbinder J1 muß mit seiner Brücke angeschlossen
bleiben, wenn kein externer Anschluß erfolgt. Die Vorvakuumpumpe und die
TwisTorr-Pumpe können gleichzeitig eingeschaltet werden.
32/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Gebrauchsanleitung
Gebrauch
2
Steuerungen, Anzeigen und Verbinder des
Controllers
Der folgende Abschnitt beschreibt die vordere und hintere Konsole
des Controllers. Für weitere Einzelheiten siehe "Technical Information".
Fronttafel der Controller
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
84301-AG
FS AG
Turbo-V
Abbildung 2
Fronttafel der Controller TwisTorr 84 -AG
1
Taste für die Anzeige der Parameter "cycle number", "cycle time" und "pump life".
2
Taste für die Einstellung des Modus LOW SPEED. Sie ist nur aktiv, wenn der Steuermodus
auf Fronttafel eingestellt ist. Bei einmaligem Drücken läuft die Pumpe in BereitschaftsGeschwindigkeit. Bei nochmaligem Drücken wird der Modus LOW SPEED deaktiviert.
3
Taste für die Anzeige der Parameter "pump current", "pump temperature", "pump power"
und "rational speed". Sie ist immer aktiv, unabhängig vom gewählten Betriebsmodus. Bei
gemeinsamer, mindestens 2 Sekunden langer Betätigung der Tasten 3 und 1 wird ein
Programm aktiviert, mit dem einige Betriebsparamter programmiert werden können.
4
START-, STOP/RESET-Taste. Sie ist nur aktiv, wenn der Steuermodus auf der Fronttafel
eingestellt ist. Bei einmaligem Drücken wird die Startphase aktiviert. Bei nochmaligem
Drücken stoppt die Pumpe. Bei automatischem Pumpenstopp durch Störung muß diese
Taste ein erstes Mal zur Controller-Rücksetzung und dann ein zweites Mal zum Neustarten
der Pumpe gedrückt werden.
5
Alphanumerisches Flüssigkristall-Display: Punkt-matrix, 2 Zeilen mit 16 Stellen.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
33/297
2
Gebrauchsanleitung
Gebrauch
8
7
6
1
2
5
3
Abbildung 3
4
Rücktafel der Controller TwisTorr 84 -AG
1
Eingangsverbinder der logischen Signale (der Kupplungsverbinder wird mit einer
Wiederverschließbrücke geliefert).
2
Stecker für logische Signale und Pumpenmonitor plus programmierbarer Analogausgang.
3
Stromausgangsstecker (24 V= für Pumpenkühlventilator, Vent Valve und Messinstrument).
4
Netzeingangsmodul des Controllers bestehend aus Netzsicherungen, Netzstecker und EMC
Filter.
5
Drehschalter zum Setzen der Profibus Adresse.
6
Profibus (Option).
7
Serieller Stecker zur Fernsteuerung.
8
Pumpenstecker.
34/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Gebrauchsanleitung
Bedienung
2
Bedienung
Einschalten des Controllers
Zum Einschalten des Controllers genügt es, das Netzkabel an die
Steckdose anzuschließen.
Pumpenstart
Zum Starten der Pumpe den Verrieglungseingang bestätigen und die
START Taste of der vorderen Konsole des Controllers drücken.
Pumpenstopp
Zum Stoppen der Pumpe muß die STOP-Taste an der Fronttafel
gedrückt werden.
Wartung
Die Controller der Serie TwisTorr 84 Rack sind wartungsfrei.
Eventuell erforderliche Eingriffe müssen von dazu befugtem
Fachpersonal ausgeführt werden. Bei einem Defekt kann der AgilentReparaturdienst bzw. der "Agilent advanced exchange service" in
Anspruch genommen werden, der für die Erneuerung defekter
Controller sorgt.
WARNUNG!
Vor jedem Eingriff am Controller muß der Netzstecker gezogen werden.
Ein Controller muß unter Einhaltung der einschlägigen
landesüblichen Vorschriften erfolgen.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
35/297
2
Gebrauchsanleitung
Entsorgung
Entsorgung
Bedeutung des "WEEE" Logos auf den Etiketten. Das folgende
Symbol ist in Übereinstimmung mit der EU-Richtlinie WEEE (Waste
Electrical and Electronic Equipment) angebracht. Dieses Symbol (nur
in den EU-Ländern gültig) zeigt an, dass das betreffende Produkt
nicht zusammen mit Haushaltsmüll entsorgt werden darf sondern
einem speziellen Sammelsystem zugeführt werden muss. Der
Endabnehmer sollte daher den Lieferanten des Geräts - d.h. die
Muttergesellschaft oder den Wiederverkäufer - kontaktieren, um den
Entsorgungsprozess zu starten, nachdem er die Verkaufsbedingungen
geprüft hat.
36/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Gebrauchsanleitung
Fehlermeldungen
2
Fehlermeldungen
In einigen Störungsfällen zeigt das Selbstdiagnosesystem des
Controllers die in der nachstehenden Tabelle zusammengefaßten
Meldungen an.
Tab. 1
MELDUNG
BESCHREIBUNG
BEHEBUNG
CHECK
CONNECTION
TO PUMP
Fehlfunktion der Pumpen-Controller
Verbindung.
Sicherstellen, daß das
Verbindungskabel zwischen
Pumpe und Controller an
beiden Seiten korrekt
befestigt ist und keine
Unterbrechung vorliegt. Die
Pumpe durch zweimalige
Betätigung der START-Taste
neustarten.
Oder
Die Temperatur der Pumpe ist unter
0 °C.
WAITING
INTERLOCK
Das Interlock-Signal auf dem
Verbinder P1 ist wegen der
Kurzschluß-unterbrechung
zwischen Pin 3 und Pin 8 des
Verbinders K1 oder wegen der
Öffnung des externen InterlockSignals aktiv.
Den Kurzschluß zwischen
Pin 3 und Pin 8 des
Verbinders P1 rücksetzen
oder das externe InterlockSignal schließen.
PUMP
OVERTEMP.
Die Temperatur des oberen Lagers
bzw. der Pumpe hat 60 °C
überschritten.
Warten bis die Temperatur
unter den Schwellenwert
gesunken ist. Die Pumpe
durch zweimalige
Betätigung der START-Taste
neustarten.
CONTROLLER
OVERTEMP.
Die Temperatur des Controllers hat
70 °C überschritten.
Warten bis die Temperatur
unter den Schwellenwert
gesunken ist. Die Pumpe
durch zweimalige
Betätigung der START-Taste
neustarten.
Oder
Die Temperatur des Kontrollerkühlkörpers ist über 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
37/297
2
Gebrauchsanleitung
Fehlermeldungen
38/297
MELDUNG
BESCHREIBUNG
BEHEBUNG
TOO HIGH
L0AD
Die Pumpen ist stromaufnahme
größer als die vorgesehene.
Sicherstellen, daß der
Pumpenrotor ungehindert
drehen kann. Die Pumpe
durch zweimalige
Betätigung der START-Taste
neustarten.
SHORT
CIRCUIT
Während des Normalbetriebs (nach
der Startphase) erfolgt ein
Kurzschluß der
Ausgangsverbindung.
Die Verbindung zwischen
Pumpe und Controller
prüfen. Die Pumpe durch
zweimalige Betätigung der
START-Taste neustarten.
SYSTEM
OVERRIDE
Die Pumpe wurde durch ein von
einem entfernten Kontakt
kommendes Notsignal gestoppt.
Das Netzkabel des
Controllers ausstecken und
die Störungsursache
beheben. Das Netzkabel
wieder anschließen und die
Pumpe durch zweimalige
Betätigung der START-Taste
neustarten.
OVERVOLTAGE
Defekt im Versorgungsbereich des
Controllers bzw. der Controller hat
ein falsches Signal erhalten
Die Pumpe durch zweimalige
Betätigung der START-Taste
neustar-ten. Erscheint die
Meldung wieder sollte der
Agilent-Wartungs-dienst
gerufen werden.
POWER FAIL
Defekt im Pumpenstromkreis des
Controllers.
Agilent für Wartung
kontaktieren.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
3
Mode d’emploi
Indications generales 40
Emmagasinage
41
Preparation pour l‘installation
Installation
43
Utilisation
44
42
Commandes, Indicateurs et Connecteurs 45
Description du Tableau avant
Procedures d'utilisation
45
47
Allumage du Contrôleur 47
Mise en marche de la Pompe
47
Arrêt de la Pompe 47
Entretien
47
Mise au rebut
48
Messages d'erreur
49
Traduction de la mode d’emploi originale
39/297
3
Mode d’emploi
Indications generales
Indications generales
Cet appareillage a été conçu en vue d'une utilisation professionnelle.
Il est conseillé à l'utilisateur de lire attentivement cette notice
d'instructions ainsi que toute autre indication supplémentaire
fournie par Agilent, avant l'utilisation de l'appareil. Agilent décline
par conséquent toute responsabilité en cas d'inobservation totale ou
partielle des instructions données, d'utilisation incorrecte de la part
d'un personnel non formé, d'opérations non autorisées ou d'un
emploi contraire aux réglementations nationales spécifiques. Les
contrôleurs de la série TwisTorr 84 Rack sont des convertisseurs de
fréquence, contrôlés par un microprocesseur, réalisés avec des
éléments à l'état solide et ayant des capacités d'autodiagnostic et
d'autoprotection.
Caractéristiques du contrôleur:
Caractère opérationnel de front /à distance / sériel
Pilotage à 24 Vdc du ventilateur de refroidissement pompe
Pilotage vent valve
Lecture vitesse pompe suite à la commande d’arrêt (lecture
vitesse d’arrêt)
Lecture de la pression
Interface Profibus (facultatif)
Attribution automatique tension d’entrée.
Les paragraphes suivants donnent toutes les indications nécessaires
à garantir la sécurité de l'opérateur pendant l'utilisation de
l'appareillage. Des renseignements plus détaillés se trouvent dans
l'appendice "Technical Information".
40/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Emmagasinage
Emmagasinage
3
Cette notice utilise les signes conventionnels suivants:
AVERTISSEMENT! Les messages d’avertissement attirent l'attention de l'opérateur sur une
procédure ou une manoeuvre spéciale qui, si elle n'est pas effectuée
correctement, risque de provoquer de graves lésions..
ATTENTION!
NOTE
Les messages d'attention apparaissent avant certaines procédures qui, si elles
ne sont pas observées, pourraient endommager sérieusement l'appareillage.
Les notes contiennent des renseignements importants, isolés du texte.
Emmagasinage
Pendant le transport et l'emmagasinage des contrôleurs, il faudra
veiller à respecter les conditions environnementales suivantes:
température: de - 20 °C à + 70 °C
humidité relative: de 0% à 95 % (non condensante).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
41/297
3
Mode d’emploi
Preparation pour l‘installation
Preparation pour l‘installation
Le contrôleur est fourni dans un emballage de protec-tion spécial; si
l'on constate des marques de dommages pouvant s'être produits
pendant le transport, contacter aussitôt le bureau de vente local.
Pendant l'opération d'ouverture de l'emballage, veiller tout
particulièrement à ne pas laisser tomber le contrôleur et à ne lui faire
subir aucun choc. Ne pas jeter l'emballage dans la nature. Le matériel
est entièrement recyclable et il est conforme aux directives CEE
85/399 en matière de protection de l'environnement.
Figure 1
42/297
Emballage du Contrôleur
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Installation
Installation
3
Installation
AVERTISSEMENT! Le contrôleur doit être alimenté au moyen d’un câble d'alimentation à trois
fils (voir tableau des pièces que l’on peut commander) avec une fiche du
type approuvé au niveau international en vue de la sécurité de l’usager.
Utiliser toujours ce câble d'alimentation et introduire la fiche dans une prise
pourvue d'un branchement au sol approprié à la masse, afin d'éviter toute
décharge électrique et de respecter les spécifications CE. A l'intérieur du
contrôleur se développent de hautes tensions qui peuvent causer de graves
dommages, voire la mort. Avant d'effectuer toute opération d'installation ou
d'entretien du contrôleur, le débrancher de la prise d'alimentation.
NOTE
Le contrôleur peut être installé sur une table ou à l'intérieur d'un rack prévu à
cet effet. Il est en tout cas nécessaire que l'air de refroidissement puisse
circuler librement à l'intérieur de l'appareil.Ne pas installer et/ou utiliser le
contrôleur dans des milieux exposés à des agents atmosphériques (pluie, gel,
neige), à des poussières, à des gaz de combat ainsi que dans des milieux
explosifs ou à risque élevé d'incendie.
Pendant le fonctionnement, il est nécessaire de respecter les
conditions environnementales suivantes:
température: de +5 °C à +45 °C
humidité relative: de 0 % à 95 % (non condensante).
Pour les autres connexions et pour l'installation des accessoires en
option, voir la section "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
43/297
3
Mode d’emploi
Utilisation
Utilisation
Dans ce paragraphe, on indique les principales procédures
opérationnelles. Pour tous autres détails et pour les procédures
concernant des connexions ou des éléments en option, se reporter au
paragraphe "Use" de l'appendice "Technical Information".
Avant d'utiliser le contrôleur, effectuer toutes les connexions
électriques et pneumatiques et se référer à la notice de la pompe
connectée.
AVERTISSEMENT! Pour éviter tous dommages aux personnes et à l'appareil, si la pompe est
placée sur un plateau d'appui s'assurer que ce dernier est stable. Ne jamais
faire fonctionner la pompe si la bride d'entrée n'est pas connectée au système
ou n'est pas fermée à l'aide de la bride de fermeture.
NOTE
44/297
Laisser le connecteur de réenclenchement J1 connecté à sa barrette s'il n'est
procédé à aucune connexion extérieure. La pompe à pré-vide et la pompe
TwisTorr peuvent être mises en marche simultanément.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Utilisation
Utilisation
3
Commandes, Indicateurs et Connecteurs
On présente ci-dessous le tableau de commande du Contrôleur ainsi
que les tableaux d'interconnexion. Pour de plus amples détails, se
reporter à la section "Technical Information".
Description du Tableau avant
5
LS
AG
1
R1
R2
MEASURES
increase
2
3
VACUUM TECHNOLOGIES
COUNTERS
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
FS AG
Turbo-V84
301-AG
Figure 2
Tableau avant du Contröleurs TwisTorr 84 -AG
1
Interrupteur rappelant sur l'afficheur les paramètres de cycle number, cycle time et pump life.
2
Interrupteur de sélection du mode LOW SPEED. Il n'est actif que lorsque le mode de
commande est sélectionné depuis le tableau frontal. En le pressant une fois, la pompe
tourne à vitesse “stand-by”. En le pressant une deuxième fois, on désactive le mode LOW
SPEED.
3
Interrupteur rappelant sur l'afficheur les paramètres de pump current, pump temperature,
pump power et rotational speed. Il est toujours actif, indépendamment du mode de
fonctionnement choisi. En pressant simultanément les interrupteurs 3 et 1 pendant 2
secondes au moins, on active un programme avec lequel il est possible de programmer
certains paramètres opérationnels.
4
Interrupteur envoyant les commandes de START, STOP/RESET. Il n'est actif que lorsque le
mode de commande est sélectionné depuis le tableau frontal. Une première pression de
l'interrupteur active la phase de mise en marche; une deuxième pression provoque l'arrêt
de la pompe. Si la pompe s'est arrêtée automatiquement à cause d'une panne, il faut
presser cet interrupteur une première fois pour effectuer la mise à zéro du contrôleur et
une deuxième fois pour remettre la pompe en marche.
5
Ecran alphanumérique à cristaux liquides: matrice de points, 2 lignes x 16 caractères.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
45/297
3
Mode d’emploi
Utilisation
8
7
6
1
2
5
3
Figure 3
4
Tableau arrière du Contrôleur TwisTorr 84 -AG
1
Connecteur d'entrée des signaux logiques (le connecteur d'enclenchement est doté de la
barrette de réenclenchement spéciale).
2
Connecteur signaux logiques en sortie et monitorage fréquence pompe plus sortie
analogique programmables.
3
Connecteur de sortie alimentation (24 Vdc pour le ventilateur de refroidissement pompe,
vent valve et calibre).
4
Module d’entrée alimentation contrôleur qui comprend les fusibles, la prise d’alimentation
et le filtre ENC.
5
Interrupteur à rotation pour établir l’adresse du Profibus.
6
Profibus (facultatif).
7
Connecteur sériel pour contrôle à distance
8
Connecteur pompe.
46/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Procedures d'utilisation
Procedures d'utilisation
3
Procedures d'utilisation
Allumage du Contrôleur
Pour allumer le contrôleur, il suffit d'introduire le câble
d'alimentation dans la prise du réseau
Mise en marche de la Pompe
Pour faire démarrer la pompe il faut habiliter l’entrée de interlock et
appuyer sur la touche START du panneau avant.
Arrêt de la Pompe
Pour arrêter la pompe, presser l'interrupteur STOP du tableau
frontal.
Entretien
Les contrôleurs de la série TwisTorr 84 Rack n'exigent aucun
entretien. Toute opération doit être effectuée par un personnel agréé.
En cas de panne, il est possible de s'adresser au Service de
réparation Agilent ou bien au "Agilent advance exchange service" qui
permet d'obtenir un contrôleur régénéré à la place du contrôleur
détraqué.
AVERTISSEMENT! Avant d'effectuer toute opération sur le contrôleur, débrancher le câble
d'alimentation.
En cas de mise au rebut d'un contrôleur, procéder à son élimination
conformément aux réglementations nationales en la matière.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
47/297
3
Mode d’emploi
Mise au rebut
Mise au rebut
Signification du logo "WEEE" figurant sur les étiquettes. Le
symbole ci-dessous est appliqué conformément à la directive CE
nommée "WEEE". Ce symbole (unique-ment valide pour les pays de
la Communauté euro-péenne) indique que le produit sur lequel il est
appliqué NE doit PAS être mis au rebut avec les ordures ména-gères
ou les déchets industriels ordinaires, mais passer par un système de
collecte sélective. Après avoir vérifié les termes et conditions du
contrat de vente, l’utilisateur final est donc prié de contacter le
fournisseur du dispositif, maison mère ou revendeur, pour mettre en
œuvre le processus de collecte et mise au rebut.
48/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Messages d'erreur
Messages d'erreur
3
Messages d'erreur
Dans certains cas de panne, l'ensemble de circuits d'autodiagnostic
du contrôleur présente certains mes-sages d'erreur indiqués dans le
tableau ci-dessous.
Tab. 1
MESSAGE
DESCRIPTION
INTERVENTION
CHECK
CONNECTION
TO PUMP
Dysfonctionnement de la connexion
entre la pompe et le contrôleur.
S'assurer que le câble de
connexion entre la pompe et
le contrôleur et le contrôleur
est bien fixé aux deux
extrémités et qu'il n'est pas
coupé. Presser deux fois
l'interrupteur START pour
réactiver la pompe.
Ou bien
La pompe a une température
inférieure à a 0 °C.
WAITING
INTERLOCK
Le signal d'interlock situé sur le
connecteur P1 est actif à cause de
la coupure du court-circuit entre le
pin 3 et le pin 8 du connecteur J1
ou à cause de l'ouverture du signal
d'interlock extérieur.
Rétablir le court-circuit entre
le pin 3 et le pin 8 du
connecteur P1 ou fermer le
signal d'interlock extérieur.
PUMP
OVERTEMP.
La température du palier supérieur
ou de la a dépassé 60 °C.
Attendre que la température
retourne au-dessous du
seuil.
Presser deux fois
l'interrupteur START pour
remettre la pompe en
marche.
CONTROLLER
OVERTEMP.
La température du contrôleur a
dépassé 70 °C.
Ou bien
La température du radiateur du
contrôleur est supérieure à 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Attendre que la température
retourne au-dessous du
seuil. Presser deux fois
l'interrupteur START pour
remettre la pompe en
marche.
49/297
3
Mode d’emploi
Messages d'erreur
50/297
MESSAGE
DESCRIPTION
INTERVENTION
TOO HIGH
L0AD
Pendant le fonctionnement normal
(après la phase de mise en
marche), le courant absorbé par la
pompe est plus grand que celui qui
a été programmé.
S'assurer que le rotor de la
pompe a la possibilité de
tourner librement.
Presser deux fois
l'interrupteur START pour
remettre la pompe en
marche.
SHORT
CIRCUIT
Pendant le fonctionnement normal
(après la phase de mise en
marche), la connexion de sortie est
en court-circuit.
Vérifier les connexions entre
la pompe et le contrôleur.
Presser deux fois
l'interrupteur START pour
remettre la pompe en
marche.
SYSTEM
OVERRIDE
La pompe a été arrêtée par un
signal d'alerte provenant d'un
contact éloigné.
Débrancher le câble
d'alimentation du contrôleur
et corriger la cause de
l'alerte. Reconnecter le
câble d'alimentation et
presser deux fois
l'interrupteur START pour
remettre la pompe en
marche.
OVERVOLTAGE
Il s'est produit une panne de la
section d'alimentation du
contrôleur, ou bien le contrôleur a
reçu un faux signal.
Presser deux fois
l'interrupteur START pour
remettre la pompe en
marche. Si le message se
présente à nouveau,
s'adresser à Agilent pour
l'entretien.
POWER FAIL
Panne dans la section
d’alimentation de la pompe, du
contrôleur.
S’adresser à Agilent pour
Maintenance.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
4
Manual de istrucciones
Información general
52
Almacenamiento 53
Preparación para la instalación 54
Instalación
Uso
55
56
Mandos, Indicadores y Conectores
57
Descripción del panel frontal 57
Procedimientos de uso
59
Encendido del controler59
Puesta en marcha de la Bomba 59
Parada de la Bomba
Mantenimiento
59
Eliminación
60
Mensajes de error
59
61
Traducción de las instrucciones originales
51/297
4
Manual de istrucciones
Información general
Información general
Este equipo se ha concebido para un uso profesional. El usuario
deberá leer atentamente el presente manual de instrucciones y
cualquier otra información suplementaria facilitada por Agilent antes
de utilizar el equipo. Agilent se considera libre de cualquier
responsabilidad debida al incumplimiento total o parcial de las
instrucciones, al uso poco apropiado por parte de personal sin
formación, a las operaciones no autorizadas o al uso que no cumpla
con las normas nacionales específicas. Los controlers de la serie
TwisTorr 84 Rack son convertidores de frecuencia, controlados por
un microprocesador, realizados con componentes en estado sólido y
con capacidad de autodiagnosis y autoprotección.
Características del controler:
Operatividad frontal / remoto / serial
Pilotaje de 24 Vdc del ventilador de refrigeración bomba
Pilotaje vent valve
Lectura velocidad bomba después de activación mando de parada
(lectura velocidad de parada)
Lectura de la presión
Interfaz Profibus (opcional)
Configuración automática tensión de entrada.
En los apartados siguientes se facilita toda la información necesaria
para garantizar la seguridad del operador durante el uso del equipo.
Una información más detallada se facilita en el Suplemento
"Technical Information".
52/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de istrucciones
Almacenamiento
4
Este manual utiliza los símbolos convencionales siguientes:
¡ADVERTENCIA! Los mensajes de advertencia atraen la atención del operador sobre un
¡ATENCIÓN!
NOTA
Los mensajes de atención se visualizan antes de procedimientos que, al no
respetarse, podrían provocar daños al equipo.
Las notas contienen información importante extraída del texto.
Almacenamiento
Durante el transporte y el almacenamiento de los controlers se
deberá cumplir con las condiciones ambientales siguientes:
temperatura: de -20 °C a +70 °C
humedad relativa: 0 – 95 % (no condensadora)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
53/297
4
Manual de istrucciones
Preparación para la instalación
Preparación para la instalación
El controler se suministra en un embalaje de protección especial; si
se observan señales de daños, que podrían haberse producido
durante el transporte, ponerse en contacto con la oficina de venta
más cercana.
Durante la operación de desembalaje, prestar una atención especial a
no dejar caer el controler y evitarle golpes. No dispersar el embalaje
en el medio ambiente. El material es totalmente reciclable y cumple
con la directiva CEE 85/399 para la preservación del medio
ambiente.
Figura 1
54/297
Embalaje de los Controlers
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de istrucciones
Instalación
4
Instalación
¡ADVERTENCIA! El controler debe ser alimentado mediante un cable de tres hilos (ver tabla de
los componentes que pueden ser ordenados) con una clavija del tipo
aprobado a nivel internacional con la finalidad de respetar las normas
correspondientes a la seguridad del usuario. Utilizar siempre este cable de
alimentación e introducir la clavija en un enchufe con una conexión de masa
adecuada para evitar descargas eléctricas. y respetar las especificaciones
CE. Dentro del controler se desarrollan altas tensiones que pueden causar
graves daños o la muerte. Antes de efectuar cualquier operación de
instalación o mantenimiento del controler desconectarlo del enchufe de
alimentación.
NOTA
El controler puede instalarse en una mesa o dentro de un rack específico. En
cualquier caso, es necesario que el aire de refrigeración pueda circular
libremente alrededor del aparato. No instalar y/o utilizar el controler en
ambientes expuestos a agentes atmosféricos (lluvia, hielo y nieve), polvos,
gases agresivos, en ambientes explosivos o con alto riesgo de incendio.
Durante el funcionamiento es necesario que se respeten las
condiciones ambientales siguientes:
temperatura: de +5 °C a +45 °C
humedad relativa: 0 – 95 % (no condensadora).
Para otras conexiones y la instalación de los accesorios opcionales,
véase la sección “Technical Information”.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
55/297
4
Manual de istrucciones
Uso
Uso
En este apartado se citan los procedimientos operativos principales.
Para más detalles y para procedimientos que impliquen conexiones u
opcionales especiales, les remitimos al apartado “Use” del anexo
“Technical Informations”.
Antes de usar el controler efectuar todas las conexiones eléctricas y
neumáticas y consultar el manual de la bomba conectada.
¡ADVERTENCIA! Para evitar lesiones a las personas y al aparato, si la bomba está apoyada
sobre una mesa cerciorarse que es estable. No poner en marcha nunca la
bomba si la brida de entrada no está conectada al sistema o no está cerrada
con la brida de cierre.
NOTA
56/297
El conector di cierre J1 ha de dejarse conectado con su conector puente si no
se efectúa ninguna conexión exterior. La bomba pre-vacío y la bomba TwisTorr
pueden encenderse simultáneamente.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de istrucciones
Uso
4
Mandos, Indicadores y Conectores
A continuación se ilustran el panel de mando del controler y los
paneles de interconexión. Para más detalles consultar la sección
“Technical Information”.
Descripción del panel frontal
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
FS AG
Turbo-V84301-AG
Figura 2
Panel frontal del Controller TwisTorr 84 -AG
1
Pulsador para que aparezcan en el display los parámetros cycle number, cycle time y pump life.
2
Pulsador para la selección del modo LOW SPEED. Está activado sólo cuando está
seleccionado el modo de mando del panel frontal. Apretando una vez, la bomba gira a
velocidad “stand-by”. Apretándolo una vez más se desactiva el modo LOW SPEED.
3
Pulsador para que aparezcan en el display los parámetros pump current, pump temperature,
pump power y rotational speed. Está siempre activado independientemente del modo de
funcionamiento elegido. Apretando juntos los pulsadores 3 y 1 durante 2 segundos por lo
menos, se activa un programa con el cual se pueden programar algunos parámetros operativos.
4
Pulsador para enviar los mandos de START, STOP/RESET. Está activo sólo cuando se
selecciona el modo de mando del panel frontal. Apretándolo una vez se activa la fase de
puesta en marcha; apretándolo otra vez se para la bomba. Si la bomba se ha parado
automáticamente a causa de una avería, hay que apretar este pulsador primero una vez para
efectuar el reset del controler y la segunda vez para volver a poner en marcha la bomba.
5
Display alfanumérico de cristales líquidos: matriz de puntos, 2 líneas x 16 caracteres.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
57/297
4
Manual de istrucciones
Uso
8
7
6
1
2
5
3
Figura 3
4
Panel trasero del controler TwisTorr 84 -AG
1
Conector de entrada de las señales lógicas (el conector de acoplamiento se suministra con
el conector puente específico de cierre).
2
Conector señales lógicas en salida y monitoreo frecuencia bomba y salida analógica
programable.
3
Conector de salida alimentación (24 Vdc para el ventilador de refrigeración bomba, vent
valve y calibre).
4
Módulo de entrada alimentación controler con fusibles, toma de alimentación y filtro ENC.
5
Conmutador de rotación para configurar la dirección del Profibus.
6
Profibus (opcional).
7
Conector serial para control remoto.
8
Conector bomba.
58/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de istrucciones
Procedimientos de uso
4
Procedimientos de uso
Encendido del controler
Para encender el controler es suficiente introducir el cable de
alimentación en la toma de red.
Puesta en marcha de la Bomba
Para activar la bomba es necesario habilitar la entrada de interlock y
pulsar el botón START situado en el panel frontal.
Parada de la Bomba
Para detener la bomba hay que apretar el pulsador STOP del panel
frontal.
Mantenimiento
Los controlers de la serie TwisTorr 84 Rack no necesitan ningún
mantenimiento. Cualquier operación ha de ser efectuada por
personal autorizado. En caso de avería es posible utilizar el servicio
de reparación Agilent o del “Agilent advance exchange service”, que
permite obtener un controler regenerado en vez del averiado.
¡ADVERTENCIA! Antes de efectuar cualquier operación en el controler desenchufar el cable
de alimentación.
En caso de que un controler se tenga que desguazar, efectuar su
eliminación respetando las normas nacionales específicas.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
59/297
4
Manual de istrucciones
Eliminación
Eliminación
Significado del logotipo "WEEE" presente en las etiquetas. El
símbolo que se indica a continuación, es aplicado en observancia de
la directiva CE denominada "WEEE". Este símbolo (válido sólo para
los países miembros de la Comunidad Europea) indica que el
producto sobre el cual ha sido aplicado, NO debe ser eliminado junto
con los residuos comunes sean éstos domésticos o industriales, y que,
por el contrario, deberá ser sometido a un procedimiento de recogida
diferenciada. Por lo tanto, se invita al usuario final, a ponerse en
contacto con el proveedor del dispositivo, tanto si éste es la casa
fabricante o un distribuidor, para poder proveer a la recogida y
eliminación del producto, después de haber efectuado una
verificación de los términos y condiciones contractuales de venta.
60/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de istrucciones
Mensajes de error
4
Mensajes de error
En algunos casos de avería los circuitos de autodiagnosis del
controler presenta algunos mensajes de error detallados en la tabla
siguiente.
Tab. 1
MENSAJE
DESCRIPCIÓN
ACCIÓN CORRECTIVA
CHECK
CONNECTION
TO PUMP
Mal funcionamiento en la conexión
entre la bomba y el Controler.
Comprobar que el cable de
conexión entra en la bomba
y el controler está bien fijado
por ambos extremos y no
está interrumpido.
Apretar dos veces el
pulsador START para volver
a poner en marcha la bomba.
O bien
La bomba tiene una temperatura
inferior a 0 °C.
WAITING
INTERLOCK
Está activa la señal de interlock
presente en el conector P1 a causa
de la interrupción del cortocircuito
entre el pin 3 y el pin 8 del
conector J1, o a causa de la
apertura de la señal de interlock
externo.
Eliminar el cortocircuito
entre el pin 3 y el pin 8 del
conector P1, o cerrar la señal
de interlock exterior.
PUMP
OVERTEMP.
La temperatura del rodamiento
superior o de la bomba ha
superado los 60 ºC.
Esperar a que la temperatura
vuelva por debajo del umbral.
Apretar dos veces el
pulsador START para volver
a poner en marcha la bomba.
CONTROLLER
OVERTEMP.
La temperatura del controler ha
superado los 70 ºC.
Esperar a que la temperatura
vuelva por debajo del umbral.
Apretar dos veces el
pulsador START para volver
a poner en marcha la bomba.
O bien
La temperatura del radiador del
controler es superior a 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
61/297
4
Manual de istrucciones
Mensajes de error
62/297
MENSAJE
DESCRIPCIÓN
ACCIÓN CORRECTIVA
TOO HIGH
L0AD
La corriente absorbida por la
bomba es superior a la
programada.
Comprobar que el rotor de la
bomba tiene la posibilidad de
girar libremente.
Apretar dos veces el
pulsador START para volver
a poner en marcha la bomba.
SHORT
CIRCUIT
Durante el funcionamiento normal
(tras la fase de puesta en marcha)
la conexión de salida está en
cortocircuito.
Comprobar las conexiones
entre la bomba y el controler.
Apretar dos veces el
pulsador START para volver
a poner en marcha la bomba.
SYSTEM
OVERRIDE
La bomba ha sido parada por una
señal de emergencia procedente de
un contacto remoto.
Desenchufar el cable de
alimentación del controler y
corregir la causa de la
emergencia.
Volver a conectar el cable de
alimentación y apretar dos
veces el pulsador START
para volver a poner en
marcha la bomba.
OVERVOLTAGE
Se ha producido una avería en la
sección de alimentación del
controler o el controler ha recibido
una señal espurio.
Apretar dos veces el
pulsador START para volver
a poner en marcha la bomba.
Si el mensaje se vuelve a
presentar dirigirse a Agilent
para el mantenimiento.
POWER FAIL
Avería en la sección de
alimentación de la bomba, del
controler.
Ponerse en contacto con
Agilent para el
Mantenimiento.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
5
Manual de Istruções
Informações gerais
Armazenagem
64
65
Preparação para a instalação
Instalação
67
Utilização
68
66
Comandos, Indicadores e Conectores
Descrição painel frontal
69
69
Procedimentos de uso 71
Acendimento do Controller 71
Activação da bomba
71
Paragem da bomba 71
Manutenção
71
Eliminação
72
Mensagens de erro
73
Tradução das instruções originais
63/297
5
Manual de Istruções
Informações gerais
Informações gerais
Esta aparelhagem destina-se ao uso profissional. O utilizador deve ler
atentamente o presente manual de instruções e todas as informações
adicionais fornecidas pela Agilent antes de utilizar a aparelhagem. A
Agilent não se responsabiliza pela inobservância total ou parcial das
instruções, pelo uso indevido por parte de pessoas não treinadas, por
operações não autorizadas ou pelo uso contrário às normas nacionais
específicas.
Os controllers da série TwisTorr 84 Rack são conversores de
frequência, controlados por um microprocessador, realizados com
componentes em estado sólido e com capacidade de autodiagnóstico
e autoprotecção.
Características do controller:
Operatividade frontal / remota / serial
Pilotagem em 24 Vdc da ventoinha de resfriamento bomba
Pilotagem vent valve
Leitura velocidade bomba seguindo ao comando de paragem
(leitura velocidade de paragem)
Leitura da pressão
Interface Profibus (opcional)
Impostação automática tensão de entrada.
Nos parágrafos seguintes estão descritas todas as informações
necessárias para garantir a segurança do operador durante o uso da
aparelhagem. Informações pormenorizadas são fornecidas no
apêndice "Technical Information".
64/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de Istruções
Armazenagem
5
Este manual utiliza as seguintes convenções:
ATENÇAO!
As mensagens de atenção chamam a atenção do operador para um
correctamente, pode provocar graves lesões pessoais.
CUIDADO!
NOTA
As mensagens de cuidado são visualizadas antes de procedimentos que, se não
observados, podem causar danos à aparelhagem.
As notas contêm informações importantes destacadas do texto.
Armazenagem
Durante o transporte e a armazenagem dos controllers, devem ser
satisfeitas as seguintes condições ambientais:
temperatura: de -20 °C a + 70 °C
humidade relativa: 0 – 95 % (não condensante)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
65/297
5
Manual de Istruções
Preparação para a instalação
Preparação para a instalação
O controller é fornecido numa embalagem protectora especial; se
apresentar sinais de danos, que poderiam verificar-se durante o
transporte, entrar em contacto com o escritório de vendas local.
Durante a retirada da embalagem, tomar muito cuidado para não
deixar cair o controller e para não submetê-lo a choques. Não
depositar a embalagem no meio ambiente. O material é
completamente reciclável e responde à directriz CEE 85/399 para a
protecção do meio ambiente.
Figura 1
66/297
Embalagem dos controllers
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de Istruções
Instalação
5
Instalação
ATENÇAO!
NOTA
O controller deve ser alimentado mediante um cabo de alimentação de três
fios(ver tabela das partes ordenáveis) com uma tomada de tipo aprovado a
internacional com a finalidade de segurança do usuário. Utilizar sempre
este cabo de alimentação e inserir a tomada com uma adequada ligação de
terra para evitar descargas eléctricas e para respeitar as normativas CE. No
interior do controller desenvolvem-se altas tensões que podem provocar
graves danos ou a morte. Antes de efectuar qualquer operação de instalação
ou manutenção do controller, desligar a tomada de alimentação.
O controller pode ser instalado numa mesa ou no interior de um rack específico.
Em todo caso, é necessário que o ar de refrigeração possa circular livremente ao
redor da aparelhagem. Não instalar e/ou utilizar o controller em ambientes
expostos a agentes atmosféricos (chuva, gelo, neve), poeiras, gases agressivos
ou em ambientes com perigo de explosão ou com elevado risco de incêndio.
Durante o funcionamento é necessário que sejam respeitadas as
seguintes condições ambientais:
temperatura: de +5 °C a +45 °C
humidade relativa: 0 – 95 % (não condensante).
Para as outras ligações e a instalação dos acessórios opcionais, ver a
secção "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
67/297
5
Manual de Istruções
Utilização
Utilização
Neste parágrafo são descritos os principais procedimentos
operativos. Para maiores detalhes e para procedimentos que
envolvem ligações ou peças opcionais, consultar o parágrafo "Use" do
apêndice "Technical Information".
Antes de usar o controller, efectuar todas as ligações eléctricas e
pneumáticas e consultar o manual da bomba ligada.
ATENÇAO!
NOTA
68/297
Para evitar danos às pessoas e à aparelhagem, caso a bomba esteja apoiada
numa mesa, certificar-se que esteja estável. Nunca activar a bomba se o
flange de entrada não estiver ligado ao sistema ou não estiver fechado com o
flange de fecho.
O conector de fecho J1 deve permanecer ligado à sua ponte se não é efectuada
nenhuma ligação externa. A bomba de pré-vácuo e a bomba TwisTorr podem ser
ligadas simultaneamente.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de Istruções
Utilização
5
Comandos, Indicadores e Conectores
A seguir, estão ilustrados o painel de comando do Controller e os
painéis de interconexão. Para maiores detalhes, consultar a secção
"Technical Information".
Descrição painel frontal
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
84 301-AG
FS AG
Turbo-V
Figura 2
Painel frontal do Controller TwisTorr 84 -AG
1
Botão para evidenciar no display os parâmetros, cycle number, cycle time e pump life.
2
Botão para a seleção do modo LOW SPEED. É activo somente quando for seleccionado o
modo de comando do painel frontal. Apertando uma vez, a bomba roda com velocidade
“stand-by”.. Apertando-o novamente desactiva-se o modo LOW SPEED.
3
Botão para evidenciar no display os parâmetros pump current, pump temperature, pump
power e rotational speed. É sempre activo independentemente do modo de funcionamento
escolhido. Apertando os botões 3 e 1 em conjunto pelo menos 2 segundos é activado um
programa com o qual é possível programar alguns parâmetros operativos.
4
Botão para enviar os comandos de START, STOP/RESET. É activo somente quando for
selecionado o modo de comando do painel frontal. Apertando-o uma vez activa-se a fase de
arranque; apertando-o novamente pára a bomba. Se a bomba parou automaticamente por
causa de uma avaria, ocorre apertar este botão uma primeira vez para executar o reset do
controller e uma segunda vez para reiniciar a bomba.
5
Display alfanumérico com cristais líquidos: matriz de pontos 2 linhas x 16 caracteres.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
69/297
5
Manual de Istruções
Utilização
8
7
6
1
2
5
3
Figura 3
4
Painel posterior dos Controllers TwisTorr 84 -AG
1
Conector de entrada dos sinais lógicos (o conector de acoplamento é fornecido com ponte
específica de fecho).
2
Conector sinais lógicos na saída e monitoragem freqüência bomba mais saída analógica
programável.
3
Conector de saída alimentação (24 Vdc para a ventoinha resfriamento bomba, vent valve e
calibragem).
4
Modulo de entrada alimentação controller que compreende os fusíveis, a tomada de
alimentação e o filtro ENC.
5
Switch em rotação para impostar o endereço do Profibus.
6
Profibus (opcional).
7
Conector serial para controle de remoto.
8
Conector bomba.
70/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de Istruções
Procedimentos de uso
5
Procedimentos de uso
Acendimento do Controller
Para ligar o controller, é suficiente inserir o cabo de alimentação na
tomada de rede.
Activação da bomba
Para ligar a bomba ocorre habilitar a entrada de interlock e apertar o
botão START do painel frontal.
Paragem da bomba
Para parar a bomba, é necessário premer o botão STOP do painel
frontal.
Manutenção
Os controllers da série TwisTorr 84 Rack não requerem qualquer
manutenção. Todas as operações devem ser efectuadas por pessoal
autorizado.
Em caso de defeito é possível utilizar o serviço de reparação Agilent
ou o "Agilent advanced exchange service", que permite obter um
controller regenerado que substitua o controller com defeito.
ATENÇAO!
Antes de efectuar qualquer operação no controller, desligar o cabo de
alimentação.
Caso um controller deva ser destruído, proceder à sua eliminação
respeitando as normas nacionais específicas.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
71/297
5
Manual de Istruções
Eliminação
Eliminação
Significado do logótipo "WEEE" presente nos rótulos. O símbolo
abaixo indicado é aplicado de acordo com a directiva CE denominada
"WEEE". Este símbolo (válido apenas para os países da
Comunidade Europeia) indica que o produto no qual está aplicado
NÃO deve ser eliminado juntamente com os resíduos domésticos ou
industriais comuns, mas deve ser dirigido a um sistema de recolha
diferenciada. Portanto, convidamos o utilizador final a contactar o
fornecedor do dispositivo, seja este o fabricante ou um revendedor,
para encaminhar o processo de recolha e eliminação, após a
oportuna verificação dos termos e condições do contrato de venda.
72/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Manual de Istruções
Mensagens de erro
5
Mensagens de erro
Em alguns casos de defeitos, os circuitos de autodiagnóstico do
controller apresentam mensagens de erro relacionadas na tabela
abaixo.
Tab. 1
MENSAGEM
DESCRIÇÃO
ACÇÃO CORRECTIVA
CHECK
CONNECTION
TO PUMP
Mau funcionamento na ligação
entre a bomba e o controller.
Verificar se o cabo de
ligação entre a bomba e o
controller está bem fixado
em ambas as extremidades
e não está interrompido.
Premer duas vezes o botão
START para reactivar a
bomba.
Ou
A bomba possui temperatura
inferior a 0 °C.
WAITING
INTERLOCK
É activado o sinal de interlock
existente no conector P1 devido à
interrupção do curto circuito entre
o pin 3 e o pin 8 do conector J1 ou
devido à abertura do sinal de
interlock externo.
Restabelecer o curto circuito
entre o pin 3 e o pin 8 do
conector P1 ou fechar o
sinal de interlock externo.
PUMP
OVERTEMP.
A temperatura do rolamento
superior ou da bomba superou os
60 ºC.
Aguardar até que a
temperatura volte ao limite
estabelecido. Premer duas
vezes o botão START para
reactivar a bomba.
CONTROLLER
OVERTEMP.
A temperatura do controller
superou
os 70 ºC.
Aguardar até que a
temperatura volte ao limite
estabelecido. Premer duas
vezes o botão START para
reactivar a bomba.
Ou
A temperatura do radiador do
controller é superior a 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
73/297
5
Manual de Istruções
Mensagens de erro
74/297
MENSAGEM
DESCRIÇÃO
ACÇÃO CORRECTIVA
TOO HIGH
L0AD
Durante o funcionamento normal
(após a fase de accionamento) a
corrente absorvida pela bomba é
maior do que a programada.
Verificar se o rotor da
bomba pode rodar
livremente. Premer duas
vezes o botão START para
reactivar a bomba.
SHORT
CIRCUIT
Durante o funcionamento normal
(após a fase de accionamento) a
conexão de saída está em curto
circuito.
Verificar as ligações entre a
bomba e o controller.
Premer duas vezes o botão
START para reactivar a
bomba.
SYSTEM
OVERRIDE
A bomba parou por um sinal de
emergência proveniente de um
contacto remoto.
Remover o cabo de
alimentação do controller e
corrigir a causa da
emergência. Ligar
novamente o cabo de
alimentação e premer duas
vezes o botão START para
reactivar a bomba.
OVERVOLTAGE
Verificou-se um defeito na secção
de alimentação do controller, ou o
controller recebeu um sinal falso.
Premer duas vezes o botão
START para reactivar a
bomba. Se a mensagem se
reapresentar, dirigir-se à
Agilent para a manutenção.
POWER FAIL
Avaria na seção de alimentação da
bomba, do controller.
Dirigir-se a Agilent para
Manutenção.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
6
Bedrijfshandleiding
Algemene informatie 76
Opslag 77
Voorbereiding voor installatie
Installatie
79
Gebruik
80
78
Bedieningsorganen, Controlelampjes en Connectoren van 81
Beschrijving frontpaneel
Gebruiksprocedures
81
81
Inschakelen van de controller
Starten van de pomp
83
83
Stoppen van de pomp 83
Onderhoud
83
Afvalverwerking 84
Foutmeldingen
85
Vertaling van de originele instructies
75/297
6
Bedrijfshandleiding
Algemene informatie
Algemene informatie
Deze apparatuur is bestemd voor beroepsmatig gebruik. De gebruiker
wordt verzocht aandachtig deze handleiding en alle overige door
Agilent verstrekte informatie door te lezen alvorens het apparaat in
gebruik te nemen. Agilent acht zich niet aansprakelijk voor de
gevolgen van het niet of gedeeltelijk in acht nemen van de
aanwijzingen, onoordeelkundig gebruik door niet hiervoor opgeleid
personeel, reparaties waarvoor geen toestemming is verkregen of
gebruik in strijd met de specifieke nationale wetgeving. De
controllers van de TwisTorr 84 Rack serie zijn frequentieomzetters
die gestuurd worden door een microprocessor, zijn gemaakt van
halfgeleiderele-menten en zijn in staat om zelfdiagnose en
zelfbescherming uit te voeren.
Kenmerken van de controller:
Bediening frontaal / op afstand / serieel
Sturing met 24 Vdc van de koelventilator van de pomp
Sturing vent valve
Lezen snelheid pomp na stopcommando (lezen stopsnelheid)
Lezen van de druk
Interface Profibus (optie)
Automatische instelling ingangsspanning.
In de volgende paragrafen is alle informatie vermeld om de veiligheid
van de operator tijdens het gebruik van de apparatuur te verzekeren.
Gedetailleerde informatie is te vinden in de bijlage "Technical
information".
76/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bedrijfshandleiding
Opslag
6
Deze handleiding hanteert de volgende symbolen:
WAARSCHUWING! Bij dit symbool staat tekst die de aandacht van de operator vestigt op een
speciale procedure of methode die, indien niet correct uitgevoerd, ernstig
lichamelijk letsel kan veroorzaken.
VOORZICHTIG! Bij dit symbool staat tekst met procedures die, indien niet opgevolgd, schade aan
apparatuur kunnen veroorzaken
OPMERKING De opmerkingen bevatten belangrijke informatie die uit de tekst is gelicht.
Opslag
Tijdens het transport en de opslag van de controllers moeten de
volgende omgevingscondities aanwezig zijn:
temperatuur: van -20 °C tot +70 °C
relatieve vochtigheid: 0 – 95 % (niet condenserend)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
77/297
6
Bedrijfshandleiding
Voorbereiding voor installatie
Voorbereiding voor installatie
De controller wordt in een speciale beschermende verpakking
geleverd; als er schade wordt geconstateerd die tijdens het transport
veroorzaakt zou kunnen zijn, meteen contact opnemen met het
plaatselijke verkoopkantoor.
Zorg er bij het uitpakken voor dat de controller niet kan vallen of
stoten te verduren krijgt.
Laat de verpakking niet ergens buiten achter. Het
verpakkingsmateriaal is volledig recyclebaar en voldoet aan de EEG
milieurichtlijn 85/399.
Figuur 1
78/297
Verpakking van de controllers
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bedrijfshandleiding
Installatie
6
Installatie
WAARSCHUWING! De controller moet gevoed worden via een voedingskabel met drie draden (zie
tabel met bestelbare onderdelen) met een stekker van het internationaal
goedgekeurde type om de veiligheid van de gebruiker te waarborgen. Gebruik
altijd deze voedingskabel en steek de stekker in een geaarde contactstop om
elektrische ontladingen te voorkomen en aan de CE-specificaties te voldoen.
In de controller ontwikkelen zich hoge spanningen die zware beschadigingen
of de dood kunnen veroorzaken. Alvorens installatie- of
onderhoudswerkzaamheden uit te voeren, de controller van de contactstop
afkoppelen.
OPMERKING De controller kan op een tafel of in een speciaal rack worden geïnstalleerd. In
ieder geval moet de koellucht vrij rondom het apparaat kunnen circuleren. De
controller mag niet geïnstalleerd en/of gebruikt worden in ruimten die
blootgesteld zijn aan de weersomstandigheden (regen, vorst, sneeuw), stof,
agressieve gassen, of in ruimten met ex¬plosiegevaar of zeer hoog brandgevaar.
Tijdens de werking moeten de volgende omgevingscondities aanwezig
zijn:
temperatuur: van +5 °C tot +45 °C
relatieve vochtigheid: 0 – 95 % (niet condenserend).
Voor de overige aansluitingen en de installatie van de accessoires
wordt verwezen naar het hoofdstuk "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
79/297
6
Bedrijfshandleiding
Gebruik
Gebruik
In deze paragraaf worden de voornaamste bedieningswijzen
uitgelegd. Voor meer informatie of procedures die aansluitingen of
speciale opties betreffen wordt verwezen naar de paragraaf "Use" van
de bijlage "Technical Informations". Breng, alvorens de controller in
gebruik te nemen, alle elektrische en pneumatische aansluitingen tot
stand en raadpleeg hiervoor de handleiding van de aan te sluiten
pomp.
WAARSCHUWING! Indien de pomp op een tafel is geplaatst, controleren of deze stabiel staat om
letsel aan personen en schade aan het apparaat te voorkomen. Laat de pomp
nooit werken zonder dat de ingangsflens aan het systeem is gekoppeld of de
afsluitflens is gesloten.
OPMERKING
80/297
De connector J1 moet met zijn jumper aangesloten blijven als geen externe
aansluiting tot stand wordt gebracht. De pre-vacuümpomp en de TwisTorr pomp
mogen beide gelijktijdig ingeschakeld zijn.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bedrijfshandleiding
Gebruik
6
Bedieningsorganen, Controlelampjes en
Connectoren van
Hieronder worden het frontpaneel en het achterpaneel van de
controller geïllustreerd. Voor meer informatie wordt verwezen naar
het hoofdstuk "Technical Information".
Beschrijving frontpaneel
5
R1
R2
LS
AG
1
MEASURES
next
increase
2
3
VACUUM TECHNOLOGIES
COUNTERS
menu
previous
decrease
4
START/STOP
LOW SPEED
TwisTorr
FS AG
Turbo-V84
301-AG
Figuur 2
Frontpaneel van de Controllers TwisTorr 84 -AG
1
Drukknop voor weergave op het display van de parameters cycle number, cycle time en pump life.
2
Drukknop voor selectie van de bedrijfswijze LOW SPEED. Is alleen actief wanneer de bedrijfswijze op het
frontpaneel wordt geselecteerd. Door de knop een maal in te drukken, draait de pomp met “stand-by
“snelheid. Door de knop opnieuw in te drukken, wordt LOW SPEED geïnactiveerd.
3
Drukknop voor weergave op het display van de parameters pump current, pump temperature, pump power
en rotational speed. Is altijd actief, onafhankelijk van de gekozen bedrijfswijze. Door drukknoppen 3 en 1
gelijktijdig gedurende ten minste 2 seconden in te drukken, wordt een programma gestart waarmee enkele
bedrijfsparameters kunnen worden geprogrammeerd.
4
Drukknop voor het zenden van de sturingen START, STOP/RESET. Is alleen actief wanneer de
bedrijfswijze op het frontpaneel wordt geselecteerd. Door de knop een maal in te drukken wordt de
startfase geactiveerd; door de knop opnieuw te bedienen wordt de pomp gestopt. Als de pomp
automatisch is gestopt ten gevolge van een storing, moet deze knop een eerste maal
worden bediend om de controller te resetten en een tweede maal om de pomp weer op te starten.
5
Alfanumeriek display met vloeibare kristallen (LCD): puntjespatroon, 2 lijnen x 16 karakters.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
81/297
6
Bedrijfshandleiding
Gebruik
8
7
6
1
2
5
3
4
Achterpaneel van de controllers TwisTorr 84 -AG
1
Connector voor ingang logische signalen (de te koppelen connector wordt met de speciale
sluitklem geleverd).
2
Connector voor uitgang logische signalen en frequentiecontrole pomp plus
programmeerbare analogische uitgang.
3
Uitgangsconnector voeding (24 Vdc voor de koelventilator van de pomp, vent valve en kaliber).
4
Ingangsmodule voeding controller die de zekeringen, het voedingscontact en het ENC-filter
bevat.
5
Draaischakelaar om het adres van de Profibus in te stellen.
6
Profibus (optie).
7
Seriële connector voor afstandsbesturing.
8
Connector pomp.
82/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bedrijfshandleiding
Gebruiksprocedures
6
Gebruiksprocedures
Inschakelen van de controller
Om de controller in te schakelen, de voedingskabel in de
netcontactdoos inbrengen.
Starten van de pomp
Om de pomp te starten, de interlock-ingang inschakelen en op de
START-knop op het frontpaneel drukken.
Stoppen van de pomp
Voor het stoppen van de pomp de STOP knop op het frontpaneel
bedienen.
Onderhoud
De controllers van de serie TwisTorr 84 zijn onderhoudsvrij.
Eventuele werkzaamheden moeten door bevoegd personeel worden
uitgevoerd.
In geval van storing is het mogelijk om de reparatiedienst van Agilent
of de "Agilent advanced exchange service" in te schakelen: zo krijgt
men een ruilcontroller ter vervanging van de defecte controller.
WAARSCHUWING! Alvorens werkzaamheden aan de controller uit te voeren, de voedingskabel
afkoppelen.
Mocht de controller gesloopt worden, ga dan overeenkomstig de
specifieke nationale wetgeving te werk.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
83/297
6
Bedrijfshandleiding
Afvalverwerking
Afvalverwerking
Betekenis van het logo "WEEE" op de etiketten. Het onderstaande
symbool wordt aangebracht in overeenstemming met de EG-richtlijn
"WEEE". Dit symbool (alleen geldig voor de landen van de Europese
Gemeenschap) geeft aan dat het product waarop het is aangebracht,
NIET mag worden afgevoerd samen met mormaal huisvuil of
industrieel afval, maar gescheiden moet worden ingezameld. De
eindgebruiker wordt dus verzocht contact op te nemen met de
leverancier van het apparaat, zij het de fabrikant of een
wederverkoper, om het proces van gescheiden inzameling en
verwerking in gang te zetten, na de van toepassing zijnde termen en
voorwaarden van het verkoopcontract te hebben gecontroleerd.
84/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bedrijfshandleiding
Foutmeldingen
6
Foutmeldingen
In geval van storingen wekt het zelfdiagnose-circuit van de controller
enkele foutmeldingen op die in de volgende tabel zijn omschreven.
Tab. 1
BOODSCHAP
OMSCHRIJVING
REMEDIE
CHECK
CONNECTION
TO PUMP
Foutieve verbinding tussen pomp
en controller.
Controleren of de
verbindingskabel tussen pomp
en controller aan beide
uiteinden goed bevestigd is en
geen onderbrekingen
vertoond. Bedien twee maal
de START-knop om de pomp
weer op te starten.
Of
De pomp heeft een lagere
temperatuur dan 0 °C.
WAITING
INTERLOCK
Het interlock-signaal op connector
P1 is actief wegens onderbreking
van de kortsluiting tussen pin 3 en
pin 8 van connector J1 of wegens
het openen van het externe
interlock-signaal.
Herstel de kortsluiting tussen
pin 3 en pin 8 van connector
P1 of sluit het externe
interlock-signaal.
PUMP
OVERTEMP.
De temperatuur van het bovenste
pomplager bedraagt meer dan
60 °C.
Wacht tot de temperatuur
weer onder de drempelwaarde
is gezakt.
Bedien twee maal de STARTknop om de pomp weer op te
starten.
CONTROLLER
OVERTEMP.
De temperatuur van de controller
bedraagt meer dan 70 °C.
Wacht tot de temperatuur
weer onder de drempelwaarde
is gezakt.
Bedien twee maal de STARTknop om de pomp weer op te
starten.
Of
De temperatuur van de radiator van
de controller bedraagt meer dan
60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
85/297
6
Bedrijfshandleiding
Foutmeldingen
86/297
BOODSCHAP
OMSCHRIJVING
REMEDIE
TOO HIGH
L0AD
De stroomopname van de pomp is
groter dan de geprogrammeerde
waarde.
Controleer of de pomprotor vrij
kan draaien.
Bedien twee maal de STARTknop om de pomp weer op te
starten.
SHORT
CIRCUIT
Tijdens normale werking (na
startfase) is de uitgangsverbinding
in kortsluiting.
Controleer de verbindingen
tussen pomp en controller.
Bedien twee maal de STARTknop om de pomp weer op te
starten.
SYSTEM
OVERRIDE
De pomp is stilgelegd door een
noodsignaal afkomstig van een
afstandscontact.
Koppel de voedingskabel van
de controller af en elimineer
de oorzaak van de noodstop.
Sluit de voedingskabel weer
aan en bedien twee maal de
START-knop om de pomp
weer op te starten.
OVERVOLTAGE
Er is een storing opgetreden in de
voedingssectie van de controller of
de controller heeft een stoorsignaal
ontvangen.
Bedien twee maal de STARTknop om de pomp weer op te
starten. Als de melding weer
verschijnt zich voor onderhoud
tot Agilent wenden.
POWER FAIL
Defect in het voedingsgedeelte van
de pomp, van de controller.
Neem contact op met Agilent
voor onderhoud.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
7
Istruktionsbog
Generel Information
Opbevaring
88
89
Forberedelser før installation
Installation
91
Anvendelse
92
90
Indikatorer og Kontakter på Styreenheden 93
Beskrivelse af frontpanel
Instruktion
93
95
Start af styreenheden 95
Start af pumpen
95
Stop af pumpen
95
Vedligeholdelse
95
Bortskaffelse
96
Fejlmeddelelser
97
Oversættelse af originalinstruktionerne
87/297
7
Istruktionsbog
Generel Information
Generel Information
Dette materiel er beregnet til professionel anvendelse. Brugeren bør læse
denne brugsanvisning og anden yderligere information fra Agilent, før
udstyret anvendes. Agilent tager ikke ansvar for skader helt eller delvis
som følge af tilsidesættelse af disse instruktioner, fejlagtig brug af
personer uden tilstrækkelig kendskab, ukorrekt anvendelse af udstyret
eller håndtering, der strider imod gældende lokale regler.
Styreenhederne i TwisTorr 84 Rack serien er mikroprocessorstyrede
frekvens-omformere, der består af komponenter med fast tilstand.
Styreenhed specifikationer:
Frontal /fjern- /seriel styring
24 Vdc styring af pumpens blæser
Vent valve styring
Aflæsning af pumpens hastighed som følge af tryk på stop
(aflæsning af stophastighed)
Aflæsning af tryk
Profibus brugerflade (ekstra)
Automatisk indstilling af indgangsspændingen.
De følgende afsnit indeholder al information der behøves, for at
garantere operatørens sikkerhed under anvendelsen. Detaljeret
information findes i bilaget "Technical Information".
88/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruktionsbog
Opbevaring
7
I brugsanvisningen anvendes følgende standard-rubrikker:
ADVARSEL!
FORSIGTIG!
BEMÆRK
Advarselsmeddelelserne informerer operatøren om, at en speciel procedure
eller en vis type arbejde skal udføres præcist efter anvisningerne. I modsat
fald er der risiko for svære personskader.
Denne advarselsmeddelelse vises før procedurer, der skal følges nøje for ikke at
risikere maskinskader.
Dette gør opmærksom på vigtig information i teksten.
Opbevaring
Følgende krav til omgivelsesforholdene gælder ved transport og
opbevaring af styreenheden:
temperatur: fra -20 °C til +70 °C
relativ luftfugtighed: 0 – 95 % (ikke kondenserende)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
89/297
7
Istruktionsbog
Forberedelser før installation
Forberedelser før installation
Styreenheden leveres i en speciel beskyttende emballage. Kontakt
den lokale forhandler, hvis emballagen viser tegn på skader, der kan
være opstået under transporten. Sørg for at styreenheden ikke tabes
eller udsættes for stød ved udpakningen.
Smid ikke emballagen ud. Materialet kan genbruges 100 % og opfylder
EU-direktiv 85/399 om miljøbeskyttelse.
Figur 1
90/297
Styreenhedens emballage
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruktionsbog
Installation
7
Installation
ADVARSEL!
For at sikre brugersikkerhed skal styreenheden tilkobles et strømkabel med
tre ledere (se reservedelslisten) og godkendt stik efter internationale
standarder. Anvend udelukkende det medleverede strømkabel. I henhold til EU
reglerne må stikket kun tilsluttes et vægudtag med fungerende jordtilslutning,
for at undgå elektriske stød. Spænding frembragt i styreenheden kan nå høje
værdier og forårsage stor skade og dødsfald. Frakobel altid strømkablet, inden
der udføres installations- eller vedligeholdelsesarbejde på styreenheden.
BEMÆRK
Styreenheden kan installeres på et bord eller et velegnet stativ. I begge tilfælde
skal der være plads nok til, at luft kan cirkulerer frit omkring apparatet. Installér
og anvend ikke styreenheden i miljøer, der udsættes for påvirkninger fra
atmosfæren (regn, sne, is), damp, aggressive gasser, og ligeledes ikke i
eksplosivt eller brandfarligt miljø.
Følgende krav til omgivelsesforholdene gælder ved drift:
temperatur: fra +5 °C til +45 °C
relativ luftfugtighed: 0 – 95 % (ikke kondenserende)
For øvrige tilslutninger og installation af tilbehør henvises til
afsnittet "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
91/297
7
Istruktionsbog
Anvendelse
Anvendelse
Dette afsnit beskriver de vigtigste driftsprocedurer. For en detaljeret
beskrivelse samt procedurer, der involverer tilslutninger eller
tilbehør, henvises til afsnittet "Use" i bilag "Technical Information".
Inden styreenheden anvendes, bør samtlige elektriske og
pneumatiske tilslutninger udføres. Læs brugsanvisningen før pumpen
tilsluttes.
ADVARSEL!
Sørg for, at pumpen står fast, hvis den er installeret på et bord. Dette er for at
forebygge skader på apparatet og personer. Start aldrig pumpen, hvis
pumpetilløbet ikke er tilsluttet systemet eller er blokeret.
BEMÆRK
Afbryderkontakten J1 skal forblive tilsluttet med aktuel bro, når der ikke udføres
eksterne tilslutninger. Forvakuumpumpen og TwisTorr-pumpen skal fungere
samtidigt.
92/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruktionsbog
Anvendelse
7
Indikatorer og Kontakter på Styreenheden
Nedenfor vises styreenhedens front- og bagpanel. For yderligere
information henvises til bilag "Technical Information".
Beskrivelse af frontpanel
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr 84301-AG
FS AG
Turbo-V
Figur 2
Frontpanelet på Styreenheden TwisTorr 84 -AG
1
Trykknap til at hente cycle number, cycle time og pump lift frem på displayet.
2
Trykknap til installering af LOW SPEED driftvalg. Trykknappen fungerer kun, når der vælges
fra frontpanelet. Tryk på knappen en gang for at få pumpen til at rotere med “standby”
hastighed. Tryk på knappen igen for at gå ud af LOW SPEED driften.
3
Trykknap til at hente pump current, pump temperature, pump power og rotational speed
frem på displayet. Trykknappen fungerer altid, uanset den valgte styretype. Når
trykknapperne 3 og 1 holdes trykket ind samtidigt i mindst 2 sekunder, starter et program,
der tillader, at programmere visse driftparametre.
4
Trykknap til overføring af START, STOP/RESET. Trykknappen fungerer kun, når der vælges
fra frontpanelet. Tryk på knappen en gang for at starte pumpen, tryk på knappen igen for at
standse pumpen. Hvis pumpen standser automatisk ved en fejl, tryk på denne knap en gang
for at tilbagestille styreenheden, og yderligere en gang for at starte pumpen igen.
5
LCD-display med tal og bogstaver: punktmatrice, 2 rader med 16 tegn.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
93/297
7
Istruktionsbog
Anvendelse
8
7
6
1
2
5
3
Figur 3
4
Bagpanelet på Styreenheden TwisTorr 84 -AG
1
Indgangskontakt til logiske signaler (tilslutningskontakten leveres med speciel
forbindelsesbro).
2
Udgangskontakt til logiske signaler og kontrol af pumpens frekvens samt programmerbar
analog udgang.
3
Udtag (24 Vdc til pumpens blæser, vent valve og manometer).
4
Indgangsmodul til styreenhed omfattende sikringer, strømudtag og ENC filter.
5
Drejekontakt til indstilling af Profibus adressen.
6
Profibus (ekstra).
7
Seriel kontakt til fjernkontrol.
8
Pumpekontakt.
94/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruktionsbog
Instruktion
7
Instruktion
Start af styreenheden
Styreenheden startes ved at sætte strømkablet i vægudtaget.
Start af pumpen
Pumpen startes ved at aktivere interlock indgangen og trykke på
START-knappen på frontpanelet.
Stop af pumpen
Pumpen stopper ved at trykke på STOP-trykknappen på frontpanelet.
Vedligeholdelse
Styreenhederne i TwisTorr 84 Rack serien behøver ikke nogen
vedligeholdelse. Ethvert indgreb på pumpen skal foretages af
autoriseret personale.
Hvis pumpen går i stykker, kan man benytte sig af Agilents
reparations-service eller Agilent udvekslingsservice, hvor man kan få
en repareret pumpe i bytte for den, der er gået i stykker.
ADVARSEL!
Inden der foretages noget som helst indgreb på styreenheden, skal strømmen
først afbrydes.
Skrotning af pumpen skal foregå i overensstemmelse med det
pågældende lands særlige love.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
95/297
7
Istruktionsbog
Bortskaffelse
Bortskaffelse
Betydningen af "WEEE" logoet på mærkaterne. Nedenstående
symbol anvendes i overensstemmelse med det såkaldte EU-direktiv
"WEEE". Symbolet (kun gældende for EU-landene) viser, at
produktet, som det sidder på IKKE må bortskaffes sammen med
affald fra private husholdninger eller industriel affald men skal
indleveres på en godkendt affaldsstation. Vi opfordrer derfor
slutbrugeren til at kontakte leverandøren af anordningen, enten
fabrikken eller en forhandler, for igangsættelse af afhentnings- og
bortskaffelsesprocessen efter nøje at have kontrolleret betingelserne i
salgskontrakten.
96/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Istruktionsbog
Fejlmeddelelser
7
Fejlmeddelelser
Når visse fejl opstår, viser styreenheden ved selvdiagnose aktuelle fejl
på displayet. De mulige meddelelser listes i følgende tabel.
Tab. 1
MEDDELELSE
BESKRIVELSE
KONTROL
CHECK
CONNECTION
TO PUMP
Tilslutning mellem pumpe og
styreenhed er defekt.
Kontrollér at tilslutningskabel
mellem pumpe og styreenhed
er korrekt monteret samt at
ingen afbrydninger
forekommer. Tryk to gange på
START for at starte pumpen
igen.
eller
Temperaturen på pumpen ligger
under
0 °C.
WAITING
INTERLOCK
Interlocksignalet findes på kontakt
P1 p.g.a. kortslutning mellem stift 3
og stift 8 i kontakten J1 eller p.g.a.
at det eksterne interlocksignal er
åbent.
Tilbagestil kortslutningen
mellem stift 3 og stift 8 på
kontakt P1 eller sluk for det
eksterne interlocksignal.
PUMP
OVERTEMP.
Temperaturen på det øverste leje
eller pumpen overskrider 60 °C.
Vent på at temperaturen falder
til under tærskelværdi.
Tryk to gange på START for at
starte pumpen igen.
CONTROLLER
OVERTEMP.
Temperaturen på styreenhedens
overskrider 70 °C.
Vent på at temperaturen falder
til under tærskelværdi.
Tryk to gange på START for at
starte pumpen igen.
eller
Temperaturen på styreenhedens
køler overskrider 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
97/297
7
Istruktionsbog
Fejlmeddelelser
98/297
MEDDELELSE
BESKRIVELSE
KONTROL
TOO HIGH
L0AD
Under normal drift (efter
startfasen) forbruger pumpen en
større effekt end den
programmerede værdi.
Kontrollér om pumpens rotor
kan rotere frit.
Tryk to gange på START for at
starte pumpen igen.
SHORT
CIRCUIT
Under normal drift (efter
startfasen) er udgangseffekten
kortsluttet.
Strømmen, som optages af
pumpen overskrider den
programmerede værdi.
Kontrollér forbindelserne
mellem pumpe og styreenhed.
Tryk to gange på START for at
starte pumpen igen.
SYSTEM
OVERRIDE
Pumpen er blevet standset af et
nødstopsignal fra en fjernkontakt.
Frakobl styreenhedens
strømkabel og kontrollér
årsagen til nødstoppet. Sæt
derefter strømkablet i. Tryk to
gange på START, for at starte
pumpen igen.
OVERVOLTAGE
Der er opstået fejl i styreenhedens
fødespænding eller styreenheden
har fået et falsk signal.
Tryk to gange på STARTknappen for at starte pumpen
igen.
Hvis meddelelsen kommer
igen tag kontakt med Agilent
for nødvendig vedligeholdelse.
POWER FAIL
Der er opstået fejl i sektionen for
strømtilførsel til pumpen,
styreenheden.
Tag kontakt med Agilent for
Vedligeholdelse.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
8
Bruksanvisning
Allmän Information
Förvaring
100
101
Förberedelser för installation
Installation
103
Användning
104
102
Indikatorer och Kontakterpå Styrenheten 105
Beskrivning av frontpanel
105
Instruktioner för bruk 107
Start av styrenheten
Start av pumpen
107
107
Stopp av pumpen 107
Underhåll
107
Bortskaffning
108
Felmeddelanden 109
Översättning av originalinstruktionerna
99/297
8
Bruksanvisning
Allmän Information
Allmän Information
Utrustningen är avsedd för yrkesmässig användning. Användaren bör
läsa denna bruksanvisning, samt övrig dokumentation från Agilent före
användning av utrustningen. Agilent tar inget ansvar för skador som
helt eller delvis orsakats av åsidosättande av instruktionerna, olämplig
användning av person utan tillräcklig kunskap, obehörigt bruk av
utrustningen eller hantering som strider mot gällande lokala föreskrifter.
Styrenheterna i TwisTorr 84 Rack serien är mikroprocessor-styrda
frekvensomvandlare som består av komponenter med fast tillstånd.
Styrenheterna är försedda med självdiagnos- och självskyddsfunktion.
Styrenhetens egenskaper:
Front- / fjärr- /seriell styrning
24 Vdc styrning av pumpens kylfläkt
Vent valve styrning
Avläsning av pumphastighet efter kommando för stopp (avläsning
av stopphastighet)
Avläsning av tryck
Profibus gränssnitt (option)
Automatisk inställning av inspänning.
De följande avsnitten innehåller all information som behövs för att
garantera operatörens säkerhet under driften. Detaljerade uppgifter
finns i bilagan "Technical information".
100/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bruksanvisning
Förvaring
8
I bruksanvisningen används följande standard-rubriker:
VARNING!
Varningsmeddelandena informerar operatören om att en speciell procedur
eller en viss typ av arbete måste utföras exakt enligt anvisningarna. I annat
fall finns risk för svåra personskador.
OBSERVER!
Detta varningsmeddelande visas framför procedurer som måste följas exakt för
att undvika skador på maskinen.
OBSERVERA
Detta visar på viktig information i texten.
Förvaring
Följande krav på omgivningsförhållanden gäller vid transport och
förvaring av styrenheten:
temperatur: från -20 °C till +70 °C
relativ luftfuktighet: 0 – 95 % (utan kondens)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
101/297
8
Bruksanvisning
Förberedelser för installation
Förberedelser för installation
Styrenheten levereras i ett särskilt skyddande emballage. Kontakta
det lokala försäljningskontoret om emballaget visar tecken på skador
som kan ha uppstått under transporten.
Se till att styrenheten inte tappas eller utsätts för stötar vid
uppackningen.
Kasta inte packmaterialet i soporna. Materialet är återvinningsbart
till 100 % och uppfyller EU-direktiv 85/399 om miljöskydd.
Figur 1
102/297
Styrenhetens förpackning
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bruksanvisning
Installation
8
Installation
VARNING!
Styrenheten fungerar med en strömkabel som har tre ledare (se tabellen som
visar de delar som kan beställas) och för användarens säkerhet ska den ha
godkänd stickpropp enligt internationella standarder. Använd alltid denna
strömkabel och anslut stickproppen till ett vägguttag med fungerande
jordanslutning för att undvika elstötar och för iakttagelse av CE
specifikationer. Spänningen inuti styrenheten kan nå höga värden och
förorsaka allvarliga skador och dödsfall. Dra alltid ur strömkabeln från
vägguttaget innan något installations-eller underhållsmoment utförs på
styrenheten.
OBSERVERA
Styrenheten kan installeras på ett bord eller inuti ett därtill avsett rack. I
samtliga fall måste dock kylluften kunna cirkulera fritt kring apparaten. Installera
och använd inte styrenheten i miljöer som utsätts för påverkan från atmosfären
(regn, snö, is), damm, aggressiva gaser, och inte heller i explosiv eller
brandfarlig miljö.
Följande krav på omgivningsförhållanden gäller vid drift:
temperatur: från +5 °C till +45 °C
relativ luftfuktighet: 0 – 95 % (utan kondens)
Beträffande övriga anslutningar och installation av tillbehör hänvisas
till avsnittet "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
103/297
8
Bruksanvisning
Användning
Användning
Detta avsnitt beskriver de viktigaste driftmomenten. För en
detaljerad beskrivning samt beträffande moment som involverar
anslutningar eller tillbehör hänvisas till avsnittet "Use" i bilaga
"Technical Information".
Innan styrenheten används bör samtliga elektriska och pneumatiska
anslutningar utföras. Läs bruksanvisningen för den anslutna
pumpen.
VARNING!
Försäkra dig om att pumpen står stadigt, om den är installerad på ett bord,
detta för att förebygga skador på apparaten och personer. Sätt aldrig igång
pumpen, om intagsflänsen varken är kopplad till systemet eller är blockerad
på plats med låsflänsen.
OBSERVERA
Stängningskontakten J1 måste lämnas ansluten med aktuell brygga om ingen
extern anslutning utförs. Förvakuumpumpen och TwisTorr-pumpen kan fungera
samtidigt.
104/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bruksanvisning
Användning
8
Indikatorer och Kontakterpå Styrenheten
Nedan visas styrenhetens front- och bakpanel. För ytterligare
information hänvisas till bilaga "Technical Information".
Beskrivning av frontpanel
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
4
START/STOP
LOW SPEED
TwisTorr
FS AG
Turbo-V84301-AG
Figur 2
Frontpanelen på Styrenheten TwisTorr 84 -AG
1
Tryckknapp för att hämta parametrarna cycle number, cycle time och pump life på displayen.
2
Tryckknapp för inställning av LOW SPEED driftsätt. Tryckknappen fungerar endast när
styrsätt från frontpanelen har valts. Genom att trycka på knappen en gång kommer pumpen
att rotera vid ”standby” hastighet. Tryck på knappen igen för att gå ur LOW SPEED
driftsättet.
3
Tryckknapp för att hämta parametrarna pump current, pump temperature, pump power och
rotational speed på displayen. Tryckknappen fungerar alltid, oavsett det valda styrsättet.
När tryckknapparna 3 och 1 hålls samtidigt intryckta i minst 2 sekunder, startas ett program
som tillåter att programmera vissa driftparametrar.
4
Tryckknapp för överföring av START, STOP/RESET. Tryckknappen fungerar endast när
styrsätt från frontpanelen har valts. Tryck på knappen en gång för att starta pumpen, tryck
på knappen igen för att stanna pumpen. Om pumpen stannat automatiskt i samband med
ett fel, tryck på denna knapp en gång för att återställa styrenheten, och ytterligare en gång
för att starta om pumpen.
5
LCD-display med siffror och bokstäver: punktmatris, 2 rader med 16 tecken.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
105/297
8
Bruksanvisning
Användning
8
7
6
1
2
5
3
Figur 3
4
Bakre panel på Styrenheten TwisTorr 84 -AG
1
Ingångskontakt för logiska signaler (anslutnings-kontakten levereras med speciell
stängningsbrygga).
2
Kontakt för utgående logiksignaler och kontroll av pumpfrekvens plus programmerbar
analog utgång.
3
Uttag (24 Vdc för kylfläkt, vent valve och manometer).
4
Inmodul för styrenhet omfattande säkringar, strömuttag och ENC filter.
5
Vred för inställning av Profilbus adressen.
6
Profibus (option).
7
Seriell kontakt för fjärrkontroll.
8
Pumpkontakt.
106/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bruksanvisning
Instruktioner för bruk
8
Instruktioner för bruk
Start av styrenheten
Styrenheten startas enkelt genom att sätta strömkabeln i vägguttaget.
Start av pumpen
Vid start av pumpen måste ingången till interlock aktiveras och
START-knappen tryckas in på frontpanelen.
Stopp av pumpen
Pumpen stoppas genom att trycka på tryckknappen STOPP på
frontpanelen.
Underhåll
Styrenheterna i TwisTorr 84 Rack serien är under-hållsfria. Allt
servicearbete måste utföras av auktoriserad personal.
Om styrenheten havererar, kontakta Agilent reparationsverkstad
eller Agilent utbytesservice, som kan ersätta styrenheten med en
renoverad styrenhet.
VARNING!
Innan något arbete utförs på styrenheten måste dess strömförsörjning brytas.
Skrotning av pumpen ska ske enligt gällande lagstiftning.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
107/297
8
Bruksanvisning
Bortskaffning
Bortskaffning
Betydelse av logotypen "WEEE" på etiketterna. Symbolen som visas
nedan har tillämpats i enlighet med CD-direktivet som har betecknats
som "WEEE". Den här symbolen (gäller endast i de länder som
tillhör den Europeiska Unionen) indikerar att produkten på vilken
symbolen har applicerats INTE får skaffas bort tillsammans med
vanliga hushålls- eller industriavfall, men att däremot ett
differentierat uppsamlingssystem måste upprättas. Vi
rekommenderar därför att slutanvändaren tar kontakt med
leverantören av anordningen, oberoende om det handlar om
moderföretaget eller återförsäljaren, för att kunna starta
uppsamlings- och bortskaffningsprocessen, detta efter lämplig
kontroll av kontraktsenliga tidsgränser och försäljningsvillkor.
108/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Bruksanvisning
Felmeddelanden
8
Felmeddelanden
När vissa fel uppstår visar styrenhetens självdiagnoskrets aktuellt
felmeddelande på displayen. De möjliga meddelandena listas i
följande tabell.
Tab. 1
MEDDELANDE
BESKRIVNING
ÅTGÄRD
CHECK
CONNECTION
TO PUMP
Anslutningen mellan pump och
styrenhet är defekt.
Kontrollera att
anslutningskabeln mellan
pump och styrenhet är
ordentligt monterad samt att
inget avbrott förekommer.
Tryck två gånger på knappen
START för att starta om
pumpen.
eller också
Pumpens temperatur ligger under 0
°C.
WAITING
INTERLOCK
Interlock-signalen finns på kontakt
P1 på grund av kortslutning mellan
stift 3 och stift 8 i kontakten J1,
eller på grund av att den externa
interlock-signalen är öppen.
Åtgärda kortslutningen mellan
stift 3 och stift 8 på kontakt P1
eller stäng den externa
interlock- signalen.
PUMP
OVERTEMP.
Temperaturen på det övre lagret
eller pumpen överskrider 60 °C.
Vänta tills temperaturen
sjunker under tröskelvärdet.
Tryck två gånger på knappen
START för att starta om
pumpen.
CONTROLLER
OVERTEMP.
Temperaturen på styrenhetens
överskrider 70 °C.
Vänta tills temperaturen
sjunker under tröskelvärdet.
Tryck två gånger på knappen
START för att starta om
pumpen.
eller också
Temperaturen på styrenhetens
kylare överskrider 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
109/297
8
Bruksanvisning
Felmeddelanden
110/297
MEDDELANDE
BESKRIVNING
ÅTGÄRD
TOO HIGH
L0AD
Strömmen som absorberas av
pumpen överstiger det värde som
programmerats.
Kontrollera att pumpens rotor
kan rotera fritt.
Tryck två gånger på knappen
START för att starta om
pumpen.
SHORT
CIRCUIT
Under normal drift (efter
startmomentet) har utgången
kortslutits.
Kontrollera anslutningarna
mellan pump och styrenhet.
Tryck två gånger på knappen
START för att starta om
pumpen.
SYSTEM
OVERRIDE
Pumpen har stannats av en
nödstoppssignal från en
fjärrkontakt.
Frånkoppla styrenhetens
strömkabel och kontrollera
nödstoppets orsak.
Sätt därefter i strömkabeln.
Tryck två gånger på knappen
START för att starta om
pumpen.
OVERVOLTAGE
Ett fel i styrenhetens matningsdel
har uppstått eller styrenheten har
fått en falsk signal.
Tryck två gånger på knappen
START för att starta om
pumpen. Om meddelandet
visas igen, ta kontakt med
Agilent för nödvändigt
underhåll.
POWER FAIL
Fel i sektionen för strömtillförsel till
pumpen, styrenheten.
Ta kontakt med Agilent för
Underhåll.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
9
Instruksjon Manual
Generell informasjon 112
Lagring
113
Forberede installasjonen
Installasjon
Bruk
114
115
116
Indikatorer og Kontakter på Styreenheten 117
Beskrivelse av frontpanelet
117
Instruksjoner for bruk 119
Starte styreenheten
119
Starte pumpen 119
Stoppe pumpen
Vedlikehold
119
Eliminering
120
Feilmeldinger
121
119
Oversetting av den opprinnelige samsvarserklæringen
111/297
9
Instruksjon Manual
Generell informasjon
Generell informasjon
Dette utstyret er beregnet til bruk av profesjonelle brukere. Brukeren
bør lese denne brukerveiledningen og all annen informasjon fra Agilent
før utstyret tas i bruk. Agilent kan ikke holdes ansvarlig for hendelser
som skjer på grunn av manglende oppfølging, selv delvis, av disse
instruksjonene, feilaktig bruk av utrenet personell, ikke godkjente
endringer av utstyret eller handlinger som på noen måte er i strid med
nasjonale bestemmelser. Styreenhetene i TwisTorr 84 Rack serien er
mikroprosessor-styrte frekvensomvendere, som består av komponenter
med fast tilstand. Styreenhetene har funksjoner for selvdiagnose og
selvbeskyttelse.
Styreenhetens karakteristikker:
Frontal virksomhet / fjern / seriell
Igangsetting av kjøleviften på24 Vdc på pumpen
Igangsetting av vent valve
Avlesing av pumpehastighet etter stoppekommando (avlesing av
stoppehastighet)
Avlesing av trykk
Grensesnitt Profibus (valgfritt)
Automatisk innstilling av inngangsspenning
De følgende avsnittene inneholder all informasjon som er nødvendig for
å sikre brukeren når utstyret er i bruk. For mer detaljert bruk vises det
til tillegget "Technical Information".
112/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instruksjon Manual
Lagring
9
Denne veiledningen bruker følgende standard-protokoll:
ADVARSEL!
Disse meldingene skal tiltrekke seg brukerens oppmerksomhet til en spesiell
fremgangsmåte eller praksis som, hvis den ikke følges, kan medføre alvorlige
skader.
FORSIKTIG!
Denne advarselen vises foran fremgangsmåter som, dersom de ikke følges, kan
fore til at utstyret skades.
MERK
Merknadene inneholder viktig informasjon som er hentet fra teksten.
Lagring
Når styreenhetene transporteres eller lagres, må følgende forhold
være oppfylt:
temperatur: fra 20 °C til +70 °C
relativ fuktighet: 0 – 95 % (uten kondens)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
113/297
9
Instruksjon Manual
Forberede installasjonen
Forberede installasjonen
Styreenheten leveres i en spesiell beskyttelsesemballasje. Viser denne
tegn på skader som kan ha oppstått under transporten, må du ta
kontakt med det lokale salgskontoret.
Når styreenheten pakkes ut, må du passe på at den ikke slippes ned
eller utsettes for noen form for støt. Emballasjen må ikke kastes på
en ulovlig måte. Alle materialer er 100 % resirkulerbare og er i
samsvar med EU-direktiv 85/399 om miljøbeskyttelse.
Figur 1
114/297
Styreenhetens emballasje
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instruksjon Manual
Installasjon
9
Installasjon
ADVARSEL!
MERK
Styreenheten må koples til en strømkabel med tre ledere (se tabellen over
deler som kan bestilles) med et støpsel godkjent i henhold til internasjonale
standarder til sikkerhet for brukeren. Bruk alltid denne strømkabelen og sett
støpselet i en kontakt med passende jordledning, for å unngå elektriske støter
og for å holde seg til CE-normene. Inne i styreenheten utvikles høye
spenninger som kan føre til alvorlige skader eller dødsfall. Kople alltid
strømkabelen fra strømnettet før enhver installering eller vedlikehold av
styreenheten utføres.
Styreenheten kan installeres på et bord eller inne i et passende stativ. Uansett så
må kjøleluften kunne sirkulere fritt rundt apparatet. Ikke installer eller bruk
styreenheten i miljøer som utsettes for regn, snø eller is, støv, aggressive gasser,
eksplosjonsfarlige miljøer eller i miljøer med stor brannfare.
Under bruk må følgende forhold respekteres:
temperatur: fra +5 °C til +45 °C
relativ fuktighet: 0 – 95 % (uten kondens)
Når det gjelder andre tilkoplinger og installasjon av ekstrautstyr vises
det til avsnittet "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
115/297
9
Instruksjon Manual
Bruk
Bruk
Dette avsnittet beskriver de viktigste driftsmomentene. For en
detaljert beskrivelse samt moment som omfatter tilkoplinger eller
ekstrautstyr vises det til avsnittet "Use" i vedlegget "Technical
Information”. Før styreenheten tas i bruk bør samtlige elektriske og
pneumatiske tilkoplinger gjøres. Les brukerveiledningen for pumpen
som er tilkoplet.
ADVARSEL!
Dersom pumpen er installert på et bord må du kontrollere at pumpen står
støtt. Dette er viktig for å forhindre skader på apparatet og på personer.
Dersom inngangsflensen hverken er tilkoplet systemet eller dersom den er
blokkert av låseflensen må pumpen aldri startes opp.
MERK
Lukkekontakten J1 må være tilkoplet aktuell brygge dersom det ikke skjer en
annen ekstern tilkopling. Forvakuumpumpen og TwisTorr-pumpen må fungere
sammen.
116/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instruksjon Manual
Bruk
9
Indikatorer og Kontakter på Styreenheten
Nedenunder er frontpanelet og bakpanelet på styreenheten illustrert.
For ytterligere informasjon vises det til avsnittet "Accessories and
Spare Parts" i vedlegget "Technical Information".
Beskrivelse av frontpanelet
5
R1
R2
LS
AG
1
3
VACUUM TECHNOLOGIES
MEASURES
COUNTERS
next
increase
2
menu
previous
decrease
4
START/STOP
LOW SPEED
TwisTorr
84 301-AG
FS AG
Turbo-V
Figur 2
Frontpanelet på styreenheten TwisTorr 84 -AG
1
Trykknapp for å vise parametrene cycle number, cycle time og pump life på displayet.
2
Trykknapp for innstilling av LOW SPEED drift. Trykknappen fungerer kun når det er valgt
styremåte fra frontpanelet. Ved å trykke på knappen én gang, roterer pumpen i "stand-by"
hastighet. Trykk på knappen igjen for å gå ut av LOW SPEED drift.
3
Trykknapp for å vise parametrene pump current, pump temperature, pump power og
rotational speed på displayet. Trykknappen fungerer alltid, uavhengig av styremåten. Når
trykknappene 3 og 1 trykkes ned samtidig i minst to sekunder, startes et program som
tillater programmering av visse driftsparametre.
4
Trykknapp for overføring av START, STOP/RESET. Trykknappen fungerer kun når det er
valgt styremåte fra frontpanelet. Trykk på knappen en gang for å starte pumpen, trykk på
knappen igjen for å stanse pumpen. Har pumpen stanset automatisk i forbindelse med en
feil, trykk en gang på denne knappen for å tilbakestille styreenheten, en gang til for å startet
pumpen.
5
LCD-display med siffer og bokstaver: punkt-matrise, 2 rader med 16 tegn.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
117/297
9
Instruksjon Manual
Bruk
8
7
6
1
2
5
3
Figur 3
4
Bakpanelet på styreenheten TwisTorr 84 -AG
1
Inngangskontakt for logiske signaler (tilkoplings-kontakten leveres med spesiell
lukkebrygge).
2
Port for logiske signaler ut og monitoring av pumpefrekvens og analogisk utgang
programmerbar.
3
Port for mating ut (24 Vdc på kjølevifte på pumpen, vent valve og kaliber).
4
Inngangsmodul til mating av styreenheten som består av sikringer, matekontakt og ENCfilter.
5
Dreiebryter for innstilling av Profibusadresse.
6
Profibus (valgfritt).
7
Serialport for fjernkontroll.
8
Pumpeport.
118/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instruksjon Manual
Instruksjoner for bruk
9
Instruksjoner for bruk
Starte styreenheten
Styreenheten startes ved å sette strømkabelen i veggkontakten.
Starte pumpen
For å starte pumpen må man preparere interlockinngangen og trykke
på knappen START på frontpanelet.
Stoppe pumpen
Pumpen stoppes ved å trykke på knappen STOPP på frontpanelet.
Vedlikehold
TwisTorr 84 Rack seriens styreenheter er vedlikeholdsfrie. Alt arbeid
på styreenheten må kun utføres av autorisert personell.
Dersom styreenheten stanser, må du ta kontakt med Agilents
reparasjonservice eller med Agilents avanserte bytteservice, som kan
tilby overhalte styreenheter til erstatning for den ødelagte
styreenheten.
ADVARSEL!
Før noe arbeid utføres på styreenheten, må den frakoples strømnettet.
Dersom en styreenhet skal kasseres, må dette skje i henhold til
nasjonale bestemmelser.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
119/297
9
Instruksjon Manual
Eliminering
Eliminering
Betydelsen av symbolet på logo "WEEE" på etikettene. Symbolet
nedenunder som finnes, er anvendt i henhold til EC-direktiv kalt
"WEEE". Dette symbolet (som bare gjelder for land i Det europeiske
fellesselskap), viser at produktet som det sitter på, IKKE må
behandles som vanlig hus-industriavfall, men må legges i
kildesortering. Derfor oppfordrer man den sluttelige brukeren av
anordningen å henvende seg til leverandøren av anordningen, som
kan være et firma eller en forhandler, som sørger for oppsamling og
eliminering etter å ha kontrollert avtal og betingelser i
kjøpekontrakten.
120/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instruksjon Manual
Feilmeldinger
9
Feilmeldinger
Når det oppstår visse feil viser selvdiagnosekretsen i styreenheten
den aktuelle feilmeldingen i displayet. De aktuelle feilmeldingen
fremgår av tabellen nedenfor.
Tab. 1
MELDING
BESKRIVELSE
FORHOLDSREGEL
CHECK
CONNECTION
TO PUMP
Defekt kopling mellom pumpe og
styreenhet.
Kontroller at tilkoplingskabelen
mellom pumpe og styreenhet
er skikkelig montert samt at
kabelen ikke er skadet. Trykk
to ganger på knappen START
for å starte pumpen.
Eller
Pumpen har en temperatur under 0
°C.
WAITING
INTERLOCK
Låsesignalet for kontakt P1 skyldes
en kortslutning mellom stift 3 og
stift 8 i kontakten J1 eller fordi det
eksterne låsesignalet er åpent.
Tilbakestill kortslutningen
mellom stift 3 og stift 8 på
kontakt P1 eller steng det
eksterne låsesignalet.
PUMP
OVERTEMP.
Temperaturen på det øvre lageret
eller pumpen er over 60 °C.
Vent til temperaturen synker
under terskelverdien.
Trykk to ganger på knappen
START for å starte pumpen.
CONTROLLER
OVERTEMP.
Temperaturen på styreenhetens er
over 70 °C.
Vent til temperaturen synker
under terskelverdien.
Trykk to ganger på knappen
START for å starte pumpen.
Eller
Temperaturen på radiatoren på
styreenheten er over 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
121/297
9
Instruksjon Manual
Feilmeldinger
122/297
MELDING
BESKRIVELSE
FORHOLDSREGEL
TOO HIGH
L0AD
Den absorberte strømmen av
pumpen er større enn den som er
programmert
Kontroller om pumpens rotor
kan rotere fritt.
Trykk to ganger på knappen
START for å starte pumpen.
SHORT
CIRCUIT
Ved normal drift (etter startmomentet) er utgangen kortsluttet.
Kontroller tilkoplingene
mellom pumpe og styreenhet.
Trykk to ganger på knappen
START for å starte pumpen.
SYSTEM
OVERRIDE
Pumpen har stanset av et
nødstoppsignal en fra fjernkontakt.
Kople fra styreenhetens
strømkabel og finn frem til
årsaken til nødstoppen.
Kople deretter maskinen til
strømnettet igjen. Trykk to
ganger på knappen START for
å starte pumpen.
OVERVOLTAGE
Det har oppstått en feil i
styreenhetens matedel, eller så har
styreenheten fått et falskt signal.
Trykk to ganger på knappen
START for å starte pumpen
igjen. Vises feilmeldingen om
igjen, må du ta kontakt med
Agilent for nødvendig
vedlikehold.
POWER FAIL
Feil på matesektoren på pumpen,
på styreenheten.
Henvend deg til Agilent for
vedlikehold.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
10
Ohjekäsikirja
Yleisiä tietoja
124
Varastointi
125
Valmistelut asennusta varten
Asennus
126
127
Käyttö 128
Valvojan Säätimet, Osoittimet ja Liittimet 129
Etupaneelin kuvaus
Käyttötoimenpiteet
129
131
Valvojan käynnistys
131
Pumpun käynnistys
131
Pumpun pysäyttäminen 131
Huolto 131
Hävittäminen
132
Vianetsintä
133
Alkuperäisen ohjeiden käännös
123/297
10
Ohjekäsikirja
Yleisiä tietoja
Yleisiä tietoja
Tämä laite on tarkoitettu ammattimaiseen käyttöön. Ennen laitteen
käyttöönottoa käyttäjän tulee lukea huolellisesti mukana seuraava
käyttöohje sekä kaikki muut Agilentin toimittamat lisätiedot. Agilent ei
vastaa seurauksista, jotka johtuvat laitteen käyttöohjeiden täydellisestä
tai osittaisesta laiminlyömisestä, ammattitaidottomien henkilöiden
suorittamasta laitteen virheellisestä käytöstä, valtuuttamattomista
toimenpiteistä tai maakohtaisten säädösten ja normien vastaisesta
käytöstä.
Sarjan TwisTorr 84 Rack valvojat ovat mikroprosessoreiden valvomia
kiinteistä materiaaleista tehtyjä taajuudenmuuntimia, jotka kykenevät
itsemäärittelyyn ja itsesuojaukseen.
Valvojan ominaisuudet:
Käytettävyys etupaneelista / etäkäyttö / sarjakäyttö
Pumpun jäähdytyssiivikon 24V tasavirtaohjaus
Vent valve ohjaus
Pumpun nopeuden luku pysäytyskäskyn jälkeen
(pysäytysnopeuden luku)
Paineen luku
Profibus-liitäntä (valinnainen)
Automaattinen sisääntulon jännitteen asetus.
Seuraavilla sivuilla on luettavissa tarpeelliset tiedot laitteen käyttäjän
turvallisuuden takaamiseksi laitteen käytön aikana. Yksityiskohtaiset
tiedot löytyvät liitteestä "Technical Information".
124/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Ohjekäsikirja
Varastointi
10
Tämä ohjekirja käyttää seuraavia merkintöjä:
VAROITUS!
Vaara-merkinnät saavat käyttäjän huomion kiinnittymään erityisiin
toimintotapoihin, joiden seuraamatta jättäminen voi aiheuttaa vakavia
henkilövaurioita.
HUOMIO!
Huomio-merkinnät varoittavat toiminnoista, joiden laiminlyönti voi johtaa laitteen
vaurioitumiseen.
HUOM
Huomiot sisältävät tärkeää tekstistä otettua tietoa.
Varastointi
Valvojan kuljetuksen ja varastoinnin aikana tulevat seuraavat
ympäristövaatimukset olla täytettyinä:
lämpötila: -20 °C ja +70 °C asteen välillä
suhteellinen kosteus: 0 – 95 % (ilman lauhdetta)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
125/297
10
Ohjekäsikirja
Valmistelut asennusta varten
Valmistelut asennusta varten
Valvoja toimitetaan erityisessä suojaavassa pakkauksessa. Mikäli
havaitsette mahdollisesti kuljetuksen aikana tapahtuneita vaurioita,
ottakaa yhteys paikalliseen myyntitoimistoon.
Pakkauksen purkamisen yhteydessä huolehtikaa, että valvoja ei
pääse putoamaan ja välttäkää sen joutumista iskujen kohteeksi.
Älkää jättäkö pakkausta ympäristöön. Materiaali voidaan
kokonaisuudessaan kierrättää ja se vastaa EU:n 85/399 direktiiviä
ympäristön suojelusta.
Kuva 1
126/297
Valvojan pakkaus
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Ohjekäsikirja
Asennus
10
Asennus
VAROITUS!
HUOM
Käyttäjän turvallisuuden vuoksi valvojan virranottoon on käytettävä
kolmijohtimista sähkökaapelia (ks. tilattavien osien taulukko), jonka pistoke
on kansainvälisesti hyväksyttyä tyyppiä. Käytä aina tätä kaapelia ja kiinnitä
pistoke asianmukaisesti maadoitettuun pistorasiaan sähköiskujen
välttämiseksi ja CE-vaatimusten noudattamiseksi. Valvojan sisällä
muodostuu korkeajännitettä, joka voi aiheuttaa vakavia vammoja tai jopa
kuoleman. Ennen mihinkään asennus- tai huoltotoimenpiteisiin ryhtymistä
valvojan pistoke on irrotettava pistorasiasta.
Valvoja voidaan asentaa pöydän päälle tai siihen tarkoitukseen sopivan hyllyn
sisään. Joka tapauksessa huolehtikaa siitä, että riittävä jäähdytysilma pääsee
vapaasti kiertämään laitteen sisällä. Älkää asentako ja/tai käyttäkö valvojaa
tiloissa, joissa se joutuu alttiiksi ympäristötekijöille (sade, jää, lumi), pölylle,
syövyttäville kaasuille, räjähdysalttiissa ympäristössä tai tiloissa, joissa paloriski
on suuri.
Toiminnan aikana tulee noudattaa seuraavia ympäristöolosuhteita
koskevia sääntöjä:
lämpötila: 5 °C ja +45 °C välillä
suhteellinen kosteus: 0 - 95% välillä (ilman lauhdetta)
Muiden kytkentöjen ja valinnaisten lisälaitteiden asennusten
suorittamiseksi, katsokaa kappaletta "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
127/297
10
Ohjekäsikirja
Käyttö
Käyttö
Tähän kappaleeseen on kirjattu tärkeimmät käyttötoimenpiteet.
Tarkempia lisätietoja sekä kytkentöjä ja valinnaisia lisälaitteita
koskevien toimenpiteiden suorittamista käsitteleviä tietoja löydätte
kappaleesta "Käyttö", joka on "Tekniset tiedot"- kappaleen liitteenä.
Ennen valvojan käyttöä suorittakaa kaikki sähkökytkennät seuraten
kytkettävän pumpun käyttöohjeita.
VAROITUS!
HUOM
128/297
Mikäli pumppu on asetettu pöydälle, varmistakaa että se on vakaa. Näin
vältytään vammoilta ihmisille sekä itse koneelle. Älkää myöskään käyttäkö
pumppua, mikäli sisääntulon laippaa ei ole kytketty järjestelmään tai mikäli
sitä ei ole suljettu laippasulkijalla.
Sulkimen J1 liitin tulee jättää yhdyskaapelilla kytketyksi, mikäli ulkoisia
kytkentöjä ei suoriteta. Esityhjiöpumppu ja TwisTorr-pumppu voidaan käynnistää
samanaikaisesti.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Ohjekäsikirja
Käyttö
10
Valvojan Säätimet, Osoittimet ja Liittimet
Seuraavassa on kuvattu valvojan etu- ja takapaneelit. Tarkempia
lisätietoja saatte kappaleesta "Technical Information".
Etupaneelin kuvaus
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
FS AG
Turbo-V84301-AG
Kuva 2
Valvojien TwisTorr 84 -AG etupanelit
1
Painonappi, jonka avulla näyttöön saadaan kiertonumero, kiertoaika ja pumpun toiminta.
2
LOW SPEED -moodin valintaan käytettävä painonappi. Se aktivoituu vain silloin, kun
etupaneelin toiminta-moodi on valittu. Yhden kerran painettaessa pumppu kiertää
valmiustila-nopeudella. Painonappia uudelleen painettaessa LOW SPEED- moodi
disaktivoituu.
3
Painonappi, jonka avulla näyttöön saadaan pumpun sähkövirran, pumpun lämpötilan,
pumpun tehon ja kiertonopeuden parametrit. Tämä on aina aktiivi riippumatta valitusta
toimintamoodista. Painamalla painonappeja 3 ja 1 vähintään kahden sekunnin ajan,
aktivoituu ohjelma, jonka avulla on mahdollista ohjelmoida joitakin toimintaparametrejä.
4
START, STOP/RESET (KÄYNNISTYKSEN, PYSÄYTYKSEN/UUDELLEN ASETUKSEN)
käskyjen painonappi. Se aktivoituu vain silloin, kun etupaneelin toiminta-moodi on valittu.
Yhden kerran painettaessa käynnistysvaihe aktioituu. Uudelleen painettaessa pumppu
pysähtyy. Mikäli pumppu on toimintahäiriön vuoksi pysähtynyt automaattisesti, painakaa
painonappia yhden kerran, jolloin valvoja saadaan asetettua uudelleen .Toisen kerran
painonappia painettaessa pumppu käynnistyy.
5
Kirjainnumerollinen digitaalinäyttö: pistematriisi, 2 riviä x 16 merkkiä.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
129/297
10
Ohjekäsikirja
Käyttö
8
7
6
1
2
5
3
Kuva 3
4
Valvojien TwisTorr 84 -AG takapaneli
1
Logiikkasegnaalien tulokytkentä (pariliittimet toimitetaan niihin sopivilla
yhdyskaapelisulkijalla).
2
Lähtevien logiikkasignaalien ja pumpun taajuuden tarkkailun sekä ohjelmoitavan
analogisen ulostulon liitin.
3
Virran ulostuloliitin (24 V tasavirta pumpun jäähdytyssiivikolle, vent valve ja kaliiperille).
4
Valvojan tulovirran moduuli, johon sisältyvät sulakkeet, virtapistoke ja suodatin ENC.
5
Profibus-osoitteen asettamiseen tarkoitettu kiertokytkin.
6
Profibus (valinnainen).
7
Etäohjauksen sarjaliitäntä.
8
Pumpun liitin.
130/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Ohjekäsikirja
Käyttötoimenpiteet
10
Käyttötoimenpiteet
Valvojan käynnistys
Valvoja käynnistyy asetettaessa virtakaapeli pistorasiaan.
Pumpun käynnistys
Käynnistääksenne pumpun pitää ottaa käyttöön interlock-sisääntulo
ja painaa etupaneelin painiketta START.
Pumpun pysäyttäminen
Pumppu pysähtyy painettaessa etupaneelissa olevaa STOPpainonappia.
Huolto
TwisTorr 84 Rack sarjan valvojat eivät kaipaa minkäänlaista huoltoa.
Mahdolliset valvojaan tehtävät toimenpiteet tulee jättää aina
valtuutetun henkilön tehtäviksi.
Toimintahäiriön sattuessa on mahdollista käyttää Agilentin
korjauspalvelua tai "Agilent advance exchange service" -palvelua,
jolloin on mahdollista vaihtaa rikkoontunut valvoja ladattuun
valvojaan.
VAROITUS!
Ennen minkä tahansa valvojaan tehtävän toimenpiteen suorittamista
irrottakaa sähkökaapeli pistorasiasta.
Mikäli valvoja täytyy romuttaa, toimikaa sen hävittämisessä
kansallisten säädösten ja normien määräämällä tavalla.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
131/297
10
Ohjekäsikirja
Hävittäminen
Hävittäminen
Pakkausmerkinnöissä olevan WEEE-logon merkitys. Alla näkyvä
merkki on lisätty pakkaukseen EY:n ns. WEEE-direktiivin mukaisesti.
Merkki (koskee ainoastaan Euroopan Unionin jäsenmaita)
tarkoittaa, että tuotetta EI saa hävittää tavallisen kotitalous- tai
teollisuusjätteen mukana, vaan se on toimitettava erilliseen
keräyspisteeseen. Loppukäyttäjää kehotetaan sen vuoksi ottamaan
keräys- ja hävittämisprosessia varten yhteyttä laitteen toimittajaan,
olipa se sitten laitteen valmistaja tai jälleenmyyjä, tarkastettuaan
ensin kaupan sopimusehdot.
132/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Ohjekäsikirja
Vianetsintä
10
Vianetsintä
Joidenkin toimintahäiriöiden yhteydessä valvojan itsemäärittelypiiri
analysoi virheen, joka näkyy viesteinä, jotka on kuvailtu seuraavassa
taulukossa.
Tab. 1
VIESTI
VIKA
KORJAUSTOIMENPITEET
CHECK
CONNECTION
TO PUMP
Toimintahäiriö pumpun ja valvojan
liitännässä.
Tarkistakaa että pumpun ja
valvojan välinen yhteyskaapeli
on hyvin kiinnitetty päistään
eikä sen varrella ole esteitä.
Painakaa kaksi kertaa
painonappia START jolloin
pumppu käynnistyy.
Tai
Pumpun lämpötila on alempi kuin
0 °C.
WAITING
INTERLOCK
Lukitussignaali (interlock)
liittimessä P1 on aktiivinen
johtuen liittimen J1 neulojen 3 ja 8
välillä tapahtuneen oikosulun
keskeytyksestä tai ulkoisen
lukitussignaalin (interlock)
avautumisesta.
Palauttakaa liittimen P1
neulojen 3 ja 8 välinen
oikosulku tai sulkekaa
ulkopuolinen lukitussignaali
(interlock).
PUMP
OVERTEMP.
Ylemmän laakerin tai pumpun
lämpötila on ylittänyt 60 °C.
Odottakaa että lämpötila
putoaa kynnysarvon
alapuolelle. Painakaa
painonappia START kaksi
kertaa jolloin pumppu
käynnistyy.
CONTROLLER
OVERTEMP.
Valvojan muuntajan lämpötila on
70 °C.
Odottakaa, että lämpötila
putoaa kynnysarvon
alapuolelle. Painakaa
painonappia START kaksi
kertaa jolloin pumppu
käynnistyy.
Tai
Valvojan lämmittimen lämpötila on
korkeampi kuin 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
133/297
10
Ohjekäsikirja
Vianetsintä
134/297
VIESTI
VIKA
KORJAUSTOIMENPITEET
TOO HIGH
L0AD
Pumpun absorptiovirta ylittää
ohjelmoidun arvon.
Tarkistakaa, että pumpun
roottori pyörii vapaasti.
Painakaa painonappia START
kaksi kertaa jolloin pumppu
käynnistyy.
SHORT
CIRCUIT
Normaalityöskentelyn aikana
(käynni-styksen jälkeen)
poistoliitin on oikosulussa.
Tarkistakaa pumpun ja valvojan
välinen liitos. Painakaa
painonappia START kaksi
kertaa jolloin pumppu
käynnistyy.
SYSTEM
OVERRIDE
Kaukokytkimestä tuleva
hälytyssignaali on pysäyttänyt
pumpun.
Irroittakaa valvojan
sähkökaapeli verkkovirrasta ja
korjatkaa hälytyksen aiheuttaja.
Kytkekää sähkökaapeli
uudelleen ja painakaa
painonappia START kaksi
kertaa jolloin pumppu
käynnistyy.
OVERVOLTAGE
Valvojan sähkövirran syötössä on
ilmennyt ongelma tai valvojan
saama signaali on väärä.
Painakaa painonappia START
kaksi kertaa, jolloin pumppu
käynnistyy. Mikäli viesti näkyy
uudelleen kääntykää Agilent
huoltopalvelun puoleen.
POWER FAIL
Vika pumpun, valvojan
virransyöttöosassa.
Kääntykää Agilent-yhtiön
puoleen Huoltoa tarvittaessa.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
11
Felhasználói Kézikönyv
Általános információk 136
Tárolás
137
138
Telepítés
139
Használat
140
141
141
Használati eljárások
143
143
A szivattyú beindítása 143
A szivattyú leállítása
Karbantartás
143
143
Megsemmisítés 144
Hibaüzenetek
145
Az eredeti utasítás fordítása
135/297
11
Felhasználói Kézikönyv
Általános információk
Általános információk
Ez a berendezés hivatásos használatra tervezett. A felhasználónak, a
felhasználói kézikönyvet és minden egyéb, a Agilent által szolgáltatott
információt. A Agilent
mely a felhasználói utasítások teljes vagy részleges figyelmen kívül
használathoz, meghatalmazás nélküli beavatkozásokhoz, vagy a
A TwisTorr 84
szilárdtest-elemekkel realizált frekvencia-átalakítók, öndiagnosztikai és
saját védelmi képességekkel.
vezérlése
A vent valve vezérlése
A szivattyú sebességének leolvasása a leállítási parancsot
köve
A nyomásérték leolvasása
A bemeneti feszültség automatikus beállítása.
berendezés
használata során. Részletes információk találhatók a “Technical
136/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Felhasználói Kézikönyv
Tárolás
11
VESZÉLY!
végrehajtásra, súlyos személyi sérüléseket okozhatnak.
FIGYELEM!
figyelmen kívül hagyása a berendezés károsodásához vezethet.
MEGJEGYZÉS
Tárolás
feltételeket kell biztosítani:
-20 °C és +70 °C között
relatív nedvességtartalom: 0 – 95 % (nem lecsapódó).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
137/297
11
Felhasználói Kézikönyv
károsodás jeleit mutatja, melyek a szállítás során keletkezhettek,
kapcsolatba kell lépni a helyi forgalmazó irodával.
A kicsomagolás során különleges figyelmet kell fordítani arra, hogy a
A csomagolóanyagot nem szabad szétszórni a környezetben. Az anyag
teljes mértékben újrafelhasználható, s megfelel a
környezetvédelemmel kapcsolatos EGK 85/399-es irányelvnek.
Ábra 1
138/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Felhasználói Kézikönyv
VESZÉLY!
11
alkatrészeket lásd a
táblázatban). Mindig ezt a hálózati kábelt kell használni, s a csatlakozódugót
vezér
MEGJEGYZÉS
hó) kitett, poros, maró hatású gázt tartalmazó, robbanás- vagy fokozottan
Üzem közben az alábbi környezeti feltételeket kell biztosítani:
+5 °C és +45 °C között;
relatív nedvességtartalom: 0 – 95 % (nem lecsapódó).
A többi összekötéssel és az
alfejezetet.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
139/297
11
Felhasználói Kézikönyv
Használat
Használat
ismertetésre. További részletek és az összekötéseket vagy az
opcionális el
Information”
összeköttetést létre kell hozni, és figyelembe kell venni a
csatlakoztatott szivattyú kézikönyvét.
VESZÉLY!
Abban az esetben, ha a szivattyú egy asztalon került elhelyezésre, a
kell az asztal stabilitását. Soha nem szabad a szivattyút a bementi peremnek a
rendszerhez való csatlakoztatása, vagy a záró peremmel való lezárása nélkül
üzemeltetni.
MEGJEGYZÉS
140/297
-vákuum és a TwisTorr szivattyú
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Felhasználói Kézikönyv
Használat
11
- és hátlapja. További
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
FS AG
Turbo-V84
301-AG
Ábra 2
1
2
3
4
A TwisTorr 84 -
lehívására.
A LOW SPEED (kis sebesség) üzemmód kiválasztására szolgáló nyomógomb. Csak akkor aktív,
amikor az
by” sebességgel forog. Még egyszer megnyomva, a LOW SPEED mód kikapcsolásra kerül.
szivattyúteljesítmény
függetlenül a kiválasztott üzemmódtól. A 3-as és 1-es nyomógombot együtt legalább 2
másodpercig nyomva tartva, egy program kerül aktiválásra, melynek segítségével néhány
üzemi paraméter programozható.
Nyomógomb a START, STOP/RESET parancsok indítására. Csak akkor aktív, amikor az
aktiválásra; még egyszer megnyomva a szivattyú leállításra kerül. Ha a szivattyú valamely
5
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
141/297
11
Felhasználói Kézikönyv
Használat
8
7
6
1
2
5
3
Ábra 3
1
2
3
4
A TwisTorr 84 -
(jumper) van ellátva).
analóg kimenet számára.
számára).
tápcsatlakozót és az EMC-
5
Forgatógomb a Profibus címének beállításához.
6
Profibus (opcionális).
7
Soros csatlakozó távvezérléshez.
8
Szivattyúcsatlakozó.
142/297
4
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Felhasználói Kézikönyv
Használati eljárások
11
Használati eljárások
a hálózati
aljzatba illeszteni.
A
A szivattyú beindításához engedélyezni kell az interlock bemenetet és
nyomógombot.
Karbantartás
A TwisTorr 84
igényelnek. Valamennyi beavatkozást meghatalmazott személyzet
hajthat csak végre.
Agilent javítási szolgáltatása,
vagy a "Agilent advanced exchange service", mely a meghibásodott
VESZÉLY!
hálózati csatlakozót.
tárgykörbe tartozó nemzet
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
143/297
11
Felhasználói Kézikönyv
Az alább látható
alkalmazásra. Ez a szimbólum (mely csak az Európai Közösség
országaiban érvényes), azt jelzi, hogy a termék, melyen megtalálható,
NEM kerülhet közönséges háztartási vagy ipari hulladékkal együtt
kell továbbítani.
eljárá
feltételeinek alapos áttanulmányozása után, fel kell vennie a
kapcsolatot a berendezés szállítójával, legyen ez a gyártó vagy egy
viszonteladó.
144/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Felhasználói Kézikönyv
Hibaüzenetek
11
Hibaüzenetek
Néhány meghibásodási esetben a
hibaüzenetet jelenítenek meg (lásd az alábbi táblázatot).
Tab. 1
ÜZENET
LEÍRÁS
JAVÍTÁSI TEVÉKENYSÉG
CHECK
CONNECTION
TO PUMP
Összeköttetési hiba a szivattyú és
mindkét végén jól van-e
rögzítve és nincs e
megszakadva. A szivattyú
újraindításához kétszer
megnyomni a START
nyomógombot.
vagy
van.
WAITING
INTERLOCK
A P1 csatlakozó reteszelés jelen
jele aktív a J1 csatlakozó 3. és 8.
pin-je közti rövidzár megszakadása,
állapota következtében.
PUMP
OVERTEMP.
CONTROLLER
OVERTEMP.
Visszaállítani a P1 csatlakozó
3. és 8. pin-je közti rövidzárat,
jelet.
a szivattyú
t.
túllépte a 70 °C-t,
vagy
túllépte a 60 °C-t.
-
a küszöbérték alá esik. A
szivattyú újraindításához
kétszer megnyomni a START
nyomógombot.
a küszöbérték alá esik. A
szivattyú újraindításához
kétszer megnyomni a START
nyomógombot.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
145/297
11
Felhasználói Kézikönyv
Hibaüzenetek
ÜZENET
LEÍRÁS
JAVÍTÁSI TEVÉKENYSÉG
TOO HIGH
L0AD
A szivattyú által felvett áram
meghaladja a programozott
értéket.
, hogy a szivattyú
forgórésze szabadon foroghate. A szivattyú újraindításához
kétszer megnyomni a START
nyomógombot.
SHORT
CIRCUIT
Normál üzem közben (az indítási
összeköttetés zárlatos.
összeköttetéseket a szivattyú
újraindításához kétszer
megnyomni a START
nyomógombot.
SYSTEM
OVERRIDE
A szivattyú leállt egy
hatására.
OVERVOLTAGE
tápellátási részegységében, vagy a
csatlakozóját és megszüntetni
a vészjelzés okát.
Újra csatlakoztatni a hálózati
kábelt, és kétszer megnyomni
a START nyomógombot a
szivattyú újraindításához.
A szivattyú újraindításához
kétszer megnyomni a START
nyomógombot.
Agilent-tól karbantartási
beavatkozást kérni.
POWER FAIL
146/297
Meghibásodás a szivattyú vagy a
A Agilent-tól karbantartási
beavatkozást kérni.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
12
Podrecznik Instrukcji
Informacje ogolne
148
Magazynowanie 149
Przygotowanie do instalacji 150
Instalacja
151
Uzytkowanie
152
Sterowniki, Wskazniki I Laczniki 153
Opis pulpitu frontalnego
Procedure uzytkowania
153
155
Zaswiecenie kontrolera 155
Uruchomienie pompy
155
Zatrzymanie pompy 155
Konserwacja
155
Przetworstwo odpadow
156
Bledne informacje 157
Az eredeti utasítás fordítása
147/297
12
Podrecznik Instrukcji
Informacje ogolne
Informacje ogolne
Urzadzenie to jest przeznaczone do uzytku zawodowego. Przed
przystapieniem do korzystania uzytkownik powinien wnikliwie
przesledzic zarowno ten podrecznik zawierajacy instrukcje jak rowniez
kazda inna dostarczona przez Agilent informacje.Agilent uchyla sie od
jakiejkolwiek odpowiedzialnosci w przypadku calkowitego lub
czesciowego nie przestrzegania swoich instrukcji, przeznaczenia
urzadzenia niezgodnie z jego przeznaczeniem i jego obslugi przez
personel uprzednio nie przeszkolony, naprawy urzadzenia bez
odpowiedniej autoryzacji lub przeznaczenia niezgodnego z
obowiazujacymi, specyficznymi normami krajowymi. Kontrolery z serii
TwisTorr84 Rack sa przetwornikami czestotliwosci kontrolowanymi
przez mikroprocesor zrealizowanymi z komponentow w stanie stalym i
posiadajacymi zdolnosci samodiagnostyczne i samoochronne.
Dane kontrolera:
Operatywny frontalnie / w izolacji / seryjnie
Sterowanie turbiny chlodzenia pompy z szybkoscia 24 Vdc
Sterowanie vent valve
Odczyt szybkosci pracy pompy w momencie nakazu zatrzymania
(odczyt szybkosci w momencie zatrzymania)
Odczyt cisnienia
Posrednik Profibus ( dodatkowy)
Automatyczne ustawienie napiecia wejsciowego.
W nastepnych paragrafach zawarte sa wszystkie niezbedne informacje
dotyczace gwarancji bezpieczenstwa personelu obslugujacego
urzadzenie.
Bardziej szczegolowe informacje sa zawarte w dodatku do “Technical
Information”.
148/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Podrecznik Instrukcji
Magazynowanie
12
Podrecznik ten opiera sie na nastepujacych konwencjach:
ZAGROZENIE!
Sygnaly ostrzegajace o zagrozeniu powinny zwrocic uwage operatora na
odpowiednia specyficzna procedure ktora jezeli nie jest przestrzegana w
sposob prawidlowy moze przyczynic sie do powaznych obrazen osoby
obslugujacej.
UWAGA!
Sygnaly wzrokowe ukazujace sie przed procedura jezeli zostana zlekcewazone
moga spowodowac uszkodzenia urzadzenia..
PRZYPIS
Przypisy zawieraja najwazniejsze informacje wyciagniete z tekstu.
Magazynowanie
Kontrolery podczas transportu i przechowywania w magazynie
powinny miec nastepujace warunki otoczenia:
temperatura: od -20 °C do +70 °C
wilgotnosc wzgledna: od 0-95 %(nie kondensujaca).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
149/297
12
Podrecznik Instrukcji
Przygotowanie do instalacji
Przygotowanie do instalacji
Kontroler zostaje dostarczony w specjalnym, ochronnym
opakowaniu; jezeli opakowanie prezentuje jakiekolwiek uszkodzenia
ktore moglyby powstac podczas transportu wowczas nalezy
niezwlocznie powiadomic najblizszy, lokalny punkt sprzedazy.
Podczas operacji rozpakowywania nalezy zachowac specjalna
ostroznosc zeby nie spowodowac upadku kontrolera lub nie narazic
na uderzenia.
Nie wyrzucac opakowania poniewaz jest ono calkowicie rycyklowalne
i odpowiada normom CEE 85/399 dotyczacym ochrony srodowiska.
Posta 1 Opakowanie kontrolerow
150/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Podrecznik Instrukcji
Instalacja
12
Instalacja
ZAGROZENIE!
PRZYPIS
Kontroler jest zasilany przy uzyciu kabla skladajacego sie z trzech
przewodow (patrz tabela czesci na zamowienie) i rodzaju wtyczki
odpowiadajacej standartom miedzynarodowym gwarantujacego bezpieczne
uzytkowanie. Nalezy wylacznie uzywac tego rodzaju kabla zasilajacego i
wlaczac wtyczke do gniazdka odpowiadajacego przepisom Unii Europejskiej
tzn. posiadajacego polaczenie z masa celem wykluczenia iskrzen. We
wnetrzu kontrolera powstaja wysokie napiecia ktore moga byc przyczyna
powaznych obrazen lub wypadkow smiertelnych. Przed przystapieniem do
jakiejkolwiek operacji instalowania lub konserwacji nalezy odlaczyc go od
zrodla zasilania.
Kontroler moze byc zainstalowany na stole lub wewnatrz odpowiedniego Rack. W
obydwu przypadkach nalezy pamietac aby wokol kontrolera zapewnic swobodny
przeplyw powietrza dla prawidlowego chlodzenia. Nie instalowac i/lub uzytkowac
kontrolerow w miejscach narazonych na dzialanie warunkow atmosferycznych
(jak deszcz, mroz, snieg), pylow, gazow agresywnych w srodowisku wybuchowym
lub o duzym stopniu zagrozenia pozarowego.
Podczas pracy kontrolera nalezy zapewnic nastepujace warunki
otoczenia:
temperatura: od +5 °C do +45 °C
wilgotnosc wzgledna: 0 – 95 % (nie kondensujaca).
Sposob polaczenia i instalowania akcesoriow jest opisany w rozdziale
“Technical Information”.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
151/297
12
Podrecznik Instrukcji
Uzytkowanie
Uzytkowanie
Paragraf ten zawiera podstawowe procedury operatywne. Dla
uzyskania dodatkowych bardziej szczegolowych informacji lub
dostepu do procedur na temat polaczen lub akcesoriow skonsultowac
paragraf “Use“ znajdujacy sie w dodatku do “Technical Information“.
Przed przystapieniem do uzytkowania kontrolera wykonac wszystkie
polaczenia elektryczne i pneumatyczne podlaczenie pompy
konsultowac z odnosna instrukcja.
ZAGROZENIE!
Dla unikniecia obrazen personelu obslugujacego urzadzenie jak rowniez
uszkodzen samego urzadzenia nalezy upewnic sie, szczegolnie w przypadku
gdy pompa zostala ustawiona na stole, czy stol jest odpowiednio stabilny.Pod
zadnym pozorem nie uruchamiac pompy jezeli kolnierz wejsciowy nie jest
polaczony z systemem lub nie jest zamknieta kolnierzem zamykajacym.
PRZYPIS
W przypadku kiedy nie zostanie wykonane zadne polaczenie zewnetrzne lacznik
zamykajacy J1 powinien pozostac polaczony ze swoim mostkiem.Pompa
wstepnej prozni i pompa TwisTorr moga byc uruchomione jednoczesnie.
152/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Podrecznik Instrukcji
Uzytkowanie
12
Sterowniki, Wskazniki I Laczniki
Ponizsze rysunki przedstawiaja panel frontalny i tylny kontrolera.Dla
uzyskania dokladniejszych szczegolow skonsultowac odpowiedni
rozdzial “Technical Information”.
Opis pulpitu frontalnego
5
LS
AG
1
R1
R2
COUNTERS
MEASURES
increase
2
3
VACUUM TECHNOLOGIES
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
84 FS
AG
Turbo-V
301-AG
Posta 2 Pulpit frontalny kontrolera TwisTorr 84 -AG
1
Przycisk sluzacy do przywolania na display parametrow cycle number, cycle time I pump life.
2
Przycisk do wybierania sposobu LOW SPEED. Dziala tylko wtedy kiedy sposob sterowania jest
wybierany na pulpicie frontalnym. Naciskajac jeden, szybkosc obrotu pompy w pozycji “standby”. Naciskajac jponownie nastepuje wylaczenie sposobu LOW SPEED ponownie.
3
Przycisk sluzacy do przywolania na display parametrow pump current,, pump temperature,
pump power I rotational speed. Jest zawsze aktywny niezaleznie od wybranego sposobu
dzialania. Naciskajac jednoczesnie przyciski 3 I 1 przez conajmniej 2 secundy uruchamia sie
program przy pomocy ktorego jest mozliwe programowanie niektorych parametrow operatywnych.
4
Przycisk do przesylania sygnalu START, STOP/ RESET. Dziala tylko wtedy kiedy sposob
sterowania jest wybierany na pulpicie frontalnym naciskajac jeden raz uaktywnia sie faza
uruchomienia; naciskajac ponownie zatrzymuje sie pompe. Jezeli pompa zatrzyma sie
automatycznie z powodu uszkodzenia nalezy nacisnac przycisk jeden raz zeby zresetowac
kontrolera I poraz drugi zeby uruchomic pompe.
5
Display alfanumeryczny na cieklych krysztalach: matryca punktowana, 2 linie x 16 czcionek.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
153/297
12
Podrecznik Instrukcji
Uzytkowanie
8
7
6
1
2
5
3
Posta
4
3 Pulpit tylny kontrolerow TwisTorr 84 -AG
1
Lacznik wejsciowy sygnalow logicznych (lacznik blizniaczy jest dostarczany z specialnym
mostkiem zamykajacym
2
Lacznik wyjsciowy sygnalow logicznych i nadzor nad czestotlowoscia na wyjsciu podczas
zaprogramowanej, wielokrotnej pracy pompy.
3
Lacznik zasilania na wyjsciu (24 Vdc dla turbiny chlodzacej pompy, vent valve i kaliber).
4
Modul wejsciowy zasilania kontrolera zawierajacy bezpieczniki topikowe, gniazdko
zasilajace i filtr ENC.
5
Switch obrotowy do ustawiania kierunku Profibus.
6
Profibus (dodatkowy).
7
Lacznik seryjny do kontroli na odleglosc.
8
Lacznik pompy.
154/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Podrecznik Instrukcji
Procedure uzytkowania
12
Procedure uzytkowania
Zaswiecenie kontrolera
Do zaswiecenia kontrolera wystarczy wprowadzic kabel zasilajacy do
gniazdka sieci.
Uruchomienie pompy
Zeby uruchomic pompe nalezy odblokowac wejscie interlock i
nacisnac znajdujacy sie na pulpicie frontalnym przycik START .
Zatrzymanie pompy
Do zatrzymania pompy wystarczy nacisnac przycisk STOP znajdujacy
sie na pulpicie frontalnym.
Konserwacja
Kontroler z serii TwisTorr 84 Rack nie wymaga zadnej konserwacji.
Jakakolwiek interwencja moze byc dokonywana wylacznie przez
osoby autoryzowane.
W przypadku uszkodzenia mozliwe jest korzystanie z serwisow
naprawczych Agilent lub “Agilent advance exchange service”, w
ktorym mozna otrzymac kontroler zregenerowany zastepujac go tym
uszkodzonym.
ZAGROZENIE!
Przed wykonaniem jakiejkolwiek interwencji na kontrolerze nalezy odlaczyc
kabel zasilajacy.
W przypadku decyzji zlomowania nalezy przeprowadzic operacje
respektujac krajowe , specyficzne normy
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
155/297
12
Podrecznik Instrukcji
Przetworstwo odpadow
Przetworstwo odpadow
Objasnienie znajdujacego sie na etykiecie znaczenia logo “WEEE”.
Uzyty ponizej symbol jest zgodny z wymogiem zarzadzenia “WEEE”
Unii Europejskiej. Symbol ten (prawomocny tylko w krajach Unii
Europejskiej) oznacza, ze wyrob ktory nim zostal oznaczony NIE
moze byc przetworzony jako odpad razem z innymi domowymi lub
przemyslowymi natomiast musi byc skladowany w miejscu
przeznaczonym dla odpadow do przerobki zroznicowanej . Dlatego
tez poleca sie uzytkownikowi, , po uprzedniej weryfikacji terminu i
warunkow zawartych w kontrakcie sprzedazy, nawiazac kontakt z
dostawca lub sprzedawca urzadzenia w celu uruchomienia procesu
zbiorki i przerobu.
156/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Podrecznik Instrukcji
Bledne informacje
12
Bledne informacje
W niektorych przypadkach uszodzen obwod do autodiagnozy
kontrolera pokazuje blendne informacje przyklady sa wymienionee w
ponizszej tabeli.
Tab. 1
INFORMACJA
OPIS
AKCJA KORYGUJACA
CHECK
CONNECTION
TO PUMP
Zaklocenia na polaczeniu miedzy
pompa i kontrolerem.
Zweryfikowac czy kabel
laczacy pompe z kontrolerem
jest dobrze zamocowany na
obydwu koncach I czy nie jest
przerwany.
Nacisnac dwa razy przycisk
START dla ponownego
uruchomienia pompy.
Lub
Temperatura pompy jest ponizej
0 °C.
WAITING
INTERLOCK
Jest aktywny sygnal Interlock na
laczniku P1 spowodowany
zwarciem pomiedzy pin 3 I pin 8
lacznika J1, Lub na skutek otwarcia
sygnalu zewnetrznego interlock.
Dokonac naprawy obwodu
elektrycznego pomiedzy pin 3 i
pin 8 lacznika P1 lub zamknac
sygnal interlock zewnetrzny.
PUMP
OVERTEMP.
Temperatura gornego lozyska lub
pompy przekroczyla 60 °C.
Odczekac az temperatura sie
obnizy ponizej ustalonego
poziomu.
Nacisnac dwa razy przycisk
START dla ponownego
uruchomienia pompy.
CONTROLLER
OVERTEMP.
Temperatura w kontrolerze
przekroczyla 70 °C.
Odczekac az temperatura sie
obnizy ponizej ustalonego
poziomu.
Nacisnac dwa razy przycisk
START dla ponownego
uruchomienia pompy.
Lub
Temperatura grzejnika nie
przekracza 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
157/297
12
Podrecznik Instrukcji
Bledne informacje
158/297
INFORMACJA
OPIS
AKCJA KORYGUJACA
TOO HIGH
L0AD
Absorpcja pradu przez pompe jest
wyzsza od zaprogramowanej.
Sprawdzic czy wirnik nie ma
przeszkod w swobodnym
obrocie.
Nacisnac dwa razy przycisk
START dla ponownego
uruchomienia pompy.
SHORT
CIRCUIT
Podczas normalnej pracy (po fazie
uruchomienia) na wyjsciu sa
zwarcia.
Sprawdzic polaczenie pompy z
kontrolerem.
Nacisnac dwa razy przycisk
START dla ponownego
uruchomienia pompy.
SYSTEM
OVERRIDE
Pompa sie zatrzymala na skutek
sygnalu zagrozenia pochodzacego
od pierwotnego kontaktu.
Odlaczyc kabel zasilania
kontrolera i sprawdzic
przyczyne powstania sygnalu
zagrozenia. Podlaczyc
ponownie kabel zasilajacy i
nacisnac dwa razy przycisk
START dla ponownego
uruchomienia pompy.
OVERVOLTAGE
Nastapilo uszkodzenie w sekcji
zasilania kontrolera lub kontroler
otrzymal sygnal nieprawidlowy.
Nacisnac dwa razy przycisk
START dla ponownego
uruchomienia pompy.
Jezeli sygnal sie powtorzy
zwrocic sie do Agilent o
przeprowadzenie konserwacji.
POWER FAIL
Uszkodzenie w sekcji zasilania
pompy kontrolera.
Zwrocic sie do Agilent w celu
naprawy.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
13
Všeobecné informace 160
161
162
Instalace
163
164
Ovládání, indikátory a konektory 165
Popis
P
165
y 167
Zapalování Kontroléru 167
167
167
167
Likvidace
168
Chybné zprávy
169
159/297
13
Všeobecné informace
Všeobecné informace
státním normám, Agilent
Kontroléry sérieTwisTorr 84 Rack jsou
autodiagnostickou a samoochrannou schopností.
Charakteristiky kontroléru:
/ dálková / seriální.
zastavení).
Information".
160/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
13
!
procedury nebo specifické praktiky, která nebude-
POZOR!
POZNÁMKA
temperatura: od -20 °C do +70 °C
relativní vlhkost: 0 – 95 % (nesmí kondenzovat).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
161/297
13
Kontrolér je dodáván v speciálním ochranném balení; objeví-li se
pozor, aby kontrolér nespadl nebo aby
Postava 1
162/297
Obal kontroléru
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instalace
13
Instalace
!
kontroléru,
POZNÁMKA
nesmí instalovat v místech vystavených atmosferickým vl
velké riziko
teplota: od 5 °C do +45 °C
Relativní vlhkost: 0 – 95 % (nesmí kondenzovat).
do sekce "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
163/297
13
detajly i pro procedury
.
!
zav
POZNÁMKA
164/297
-prázdna a TwisTorr se mohou
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
13
indikátory a konektory
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
FS AG
Turbo-V84301-AG
Postava 2
TwisTorr 84 -AG
1
2
s
-
3
rychlostí “stand-by”. A stiskne-li
pump current, pump power, rotational speed,
indukce. Nezávisle od zvol
4
li se
Je aktivním j
-
spustilo.
5
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
165/297
13
8
7
6
1
2
5
3
Postava 3
4
Zadní panel Kontroléru TwisTorr 84 -AG
1
2
naprogramovatelný analogový výstup.
3
4
Vstupní napájecí modul kontroléru, který zahrnuje i tavné pojistky, napájecí zásuvku a filtr
ENC.
5
6
7
Seriální konektor na dálkovou kontrolu.
8
166/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
13
P
y
ením kabele do zásuvky na síti.
oprávnit vstup interlocku a stisknout
Kontrolér série TwisTorr 84
Agilent nebo
"Agilent advanced exchange se
!
kabel.
Bude-
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
167/297
13
Likvidace
Likvidace
Význam loga "WEEE" nacházejícího se na štítku.
"WEEE". Tento
symbol (platný jen pro státy Evropské Unie)
d
nebo prode
smluvních podmínek postará o kompletní likvidaci uvedeného
168/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Chybné zprávy
13
Chybné zprávy
enovány
v tabulce, která se nachází na následující stránce.
Tab. 1
ZPRÁVY
POPIS
CHECK
CONNECTION
TO PUMP
Chybné fungování spojení mezi
KOREKCE
mezi pumpou a kontrolérem je
Nebo
0 °C.
WAITING
INTERLOCK
Aktivní signál interlock se nachází
Znovu obnovit spojení
nakrátko mezi pin 3 a pin 8
signál vn
PUMP
OVERTEMP.
CONTROLLER
OVERTEMP.
vrátí pod mezní hodnotu.
Temperatura kontrolér
70 °C.
vrátí pod mezní hodnotu.
Nebo
Teplota radiátoru kontroléru je vyšší
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
169/297
13
Chybné zprávy
ZPRÁVY
POPIS
KOREKCE
TOO HIGH
L0AD
SHORT
CIRCUIT
Stisknout
ve zkratu.
SYSTEM
OVERRIDE
OVERVOLTAGE
Pumpa byla zastavena nouzovým
Odpojit napájecí kabel
kontaktu.
poplachu.
ipojit napájecí kabel a
Vznikla porucha v napájecí sekci
kontroléru, nebo kontrolér dostal
falešný signál.
obrátit na Agilent .
POWER FAIL
170/297
kontroléru.
obrátit na Agilent.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
14
Návod na Obsluhu
Všeobecné informácie 172
173
Príprava pre inštaláciu 174
Inštalácia
175
176
Povely, Ukazovatele a Prípojky “Controller”
177
177
179
Zapnutie “Controller”179
179
Zast
179
179
Likvidácia
180
Oznamy vád
181
Preklad originálneho návodu
171/297
14
Návod na Obsluhu
Všeobecné informácie
Všeobecné informácie
Agilent. Podnik Agilent
TwisTorr 84
procesorom,
samokontroly.
Charakteristiky controller-a:
Riadenie vent valve
zastavenia)
Automatické nastavenie vstupného napätia.
troja.
Podrobné informácie sú uvedené v dodatku "Technical Information".
172/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Návod na Obsluhu
E!
14
osobné poranenia.
POZOR!
POZNÁMKA
tieto podmienky prostredia:
teplota: od -20 °C do +70 °C
– 95 % (bez kondenzátu).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
173/297
14
Návod na Obsluhu
o
miestneho predaja.
materiálu a zodpovedá smernici CEE
prostredia.
Postava 1
174/297
Obal Controller
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Návod na Obsluhu
Inštalácia
14
Inštalácia
E!
ler” sa vytvára vysoké napätie,
-
racovnom stole alebo vo vnútri track. V
POZNÁMKA
prístroja. “Controlle
v prostredí, vystavenom
mav
prostredia:
teplota: od +5 °C do +45 °C;
– 95 % (nekondenzovaná).
"Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
175/297
14
Návod na Obsluhu
V tomto odstavci sú uvedené hlavné operatívne postupy. Pre ostatné
"Technical Information".
E!
ikdy
POZNÁMKA
PredTwisTorr
176/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Návod na Obsluhu
14
-
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr 84301-AG
FS AG
Turbo-V
Postava 2
TwisTorr 84 -AG
1
2
LOW SPEED.
3
4
5
Alfanumerický displej na tekutý kryštál: bodová matica, 2 línie x 16 písmen.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
177/297
14
Návod na Obsluhu
8
7
6
1
2
5
3
Postava 3
1
4
Zadný panel “controller TwisTorr 84 -AG
Vstupná spojka logických signálov (spojovacia spojka je doganá s príslušným uzavierajúcim
mostíkom).
2
navyše
3
4
5
Vstupný modul napájania controller-u, obsahujúci poistky, napájaciu zásuvku a filter ENC.
adresy Profibusu.
6
7
8
178/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Návod na Obsluhu
14
Zapnutie “Controller”
“Controllers” série TwisTorr 84
Agilent alebo "Agilent
E!
na “controller” vytiahnite šnúru z elektrickej
siete.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
179/297
14
Návod na Obsluhu
Likvidácia
Likvidácia
Aplikovanie
Tento symbol (platný iba pre štáty Európskej Únie)
ako
predaja.
180/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Návod na Obsluhu
Oznamy vád
14
Oznamy vád
d samodiagnostiky
strane.
Tab. 1
OZNAM
POPIS
ZÁSAH OPRAVY
CHECK
CONNECTION
TO PUMP
Nefunguje napojenie medzi
Skontrolujte,
Alebo
“controller” správne zasunutý
°C.
je prerušený.
pre znovunaštartovanie
WAITlNG
INTERLOCK
je aktívny signál interlock na
spojke P1 z dôvodu prerušenia
skratu medzi pin 3 a pin 8 spojky
J1, alebo z dôvodu otvorenia
signálu vonkajšieho interlock.
signál vonkajšieho interlock.
PUMP
OVERTEMP.
CONTROLLER
OVERTEMP.
°C.
ým teplota neklesne
Alebo
Teplota radiátora controllera
presahuje 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
181/297
14
Návod na Obsluhu
Oznamy vád
OZNAM
POPIS
ZÁSAH OPRAVY
absorbovaný prúd prevyšuje ten
naprogramovaný.
START pre znovunaštartovanie
TOO HIGH
LOAD
SHORT
CIRCUIT
naštartovaní) východzie napojenie
je v skrate.
Skontrolujte napojenia medzi
oller”.
pre znovunaštartovanie
SYSTEM
OVERRIDE
Núdzový signál, vychádzajúci z
Vytiahnite šnúru z elektrickej
dôvod alarmu.
ua
pre znovunaštartovanie
OVERVOLTAGE
Objavila sa vada v sekcii napájania
“controller”, alebo “controller”
dostal falošný signál.
pre znovunaštartovanie
firmu Agilent
POWER FAIL
182/297
Vada v napájacom systéme
Agilent.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
15
Splošne informacije
184
185
186
187
Uporaba
188
Komande, indikatorji in konektorji 189
189
Postopki uporabe
191
Vklopitev Controllera
191
191
191
191
Odlaganje opadkov
192
Obvestilo o napaki
193
Prevod navodil v izvirniku
183/297
15
Splošne informacije
Splošne informacije
Naprava je namenjena samo za strokovno rabo. Uporabnik mora
informacijo, ki jo nudi Agilent. Agilent
nacionalnih meril. Controllerji serije TwisTorr 84
pretvorniki, na katere nadzor ima mikrokrmilnik. Sestavljajo jih deli v
Osprednja/oddaljena/serijska operativnost
Upravljanje vent valve
zaustavitvene hitrosti)
Branje pritiska
Vmesnik Profibus (opcijski)
V naslednjih odstavkih so navedene vse informacije potrebne za
zagotavljanje sigurnosti uporabnika med rokovanjem s to napravo.
184/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
15
razreda:
SVARILO!
Znak svarila opozarja uporabnika, da mora pri
telesnih poškodb.
POZOR!
OPOMBA
poškoduje.
Opombe vsebujejo vse najbolj pomembne informacije iz besedila.
naslednje pogoje okolice:
temperatura: od -20 °C do +70 °C
relativna vlaga: 0 – 95 % (bez kondenzacije).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
185/297
15
Pripra
prodajalnemu biroju.
pade na tla ali da ne podlegn
okolico. Material lahko v celoti reciklirate in ustreza direktivi CEE
Slika 1
186/297
Embalaža controllera
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
15
SVARILO!
preglednico delov, ki
ES meril. Znotraj controller-jev se stvori visoka napetost, ki
OPOMBA
Controller lahko montirate na mizo ali vgradite v notranjost ustreznega rack-a. V
Controller-a ne smete montirati ali uporabiti v okolici, ki je izpostavljena
u, snegu), prahu, agresivnim plinom, v okolici
Med delovanjem morate zagotoviti naslednje pogoje okolice:
temperatura: od +5 °C do +45 °C;
relativna vlaga: 0 – 95 % (ne-kondezna).
ogledate priponko "Technical Information".
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
187/297
15
Navodila
Uporaba
Uporaba
V tem odsatvku so navedeni vsi glavni operativni postopki. Za
opcije, si lahko ogledate odstavek "Use" v priponki "Technical
Information".
SVARILO!
Da bi se izognili poškodbam bodisi oseb kot naprave, morate poskrbeti, da
zapiralno prirobnico.
OPOMBA
TwisTorr
188/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Uporaba
15
Komande, indikatorji in konektorji
Sledi prikaz prednje
informacije si ogledajte paragraf "Technical Information".
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr 84
FS AG
Turbo-V
301-AG
Slika 2
1
Prednja ploš a Controllera TwisTorr 84 -AG
Tipka za preklic na zaslonu parametrov cycle number, cycle time in pump life.
2
3
Tipka za preklic na zaslonu parametrov pump current, pump power, rotational speed,
sku
nastaviti nekatere operativne prarmetre.
4
Tipka za zagon komand START, STOP/RESET. Aktivna je samo nato, ko ste to komando izbrali
tipko enkrat pritisniti, da bi lahko controller5
.
Alfaštevi
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
189/297
15
a Navodila
Uporaba
8
7
6
1
2
5
3
Slika 3
4
Ozadnja ploš a Controllera TwisTorr 84 -AG
1
2
lahko programirate.
3
4
Vhodni modul napajanje controller-a, ki vsebuje varovalke, napajalno stikalo in filter ENC.
5
Rotacijski Switch za nastavljanje Profibusnega naslova.
6
Profibus (kot opcija)
7
Serijski konektor za nadzor iz oddaljenosti
8
190/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Postopki uporabe
15
Postopki uporabe
Vklopitev Controllera
Za vklopitev Controller-a morate napajalni kabel vtakniti
-a in pitisniti
Controllerji serije TwisTorr 84 Rack ne potrebu
Agilent ali "Agilent advanced
exchange service", ki Vam bo dal na razpolago obnovljeni controller.
SVARILO!
Pred katerikoli posegom, izklopite iz controller-a. napajalni kabel
predpisi.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
191/297
15
Odlaganje opadkov
Odlaganje opadkov
Pomen znamke "WEEE" na etiketah. Spodaj navedeni simbol je v
skladu z direktivo ES znano pod imenom "WEEE". Ta simbol (ki velja
pomeni, da izdelek NE SMETE
ODSTRANITI skupaj z ostalimi komunalnimi ali pa industrijskimi
Zato pozivamo uporabnike, da se ali pri prodajalnem centru ali pa pri
192/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Obvestilo o napaki
15
Obvestilo o napaki
controller-a nekaj obvestil o napakah kot so opisane v spodnji tabeli.
Tab. 1
OBVESTILO
OPIS
CHECK
CONNECTION
TO PUMP
controller-a.
POPRAVA
controller-em na obeh koncih
trdno pritrjen in da ni
prekinjen. Dvakrat pritisnite
tipko START za ponoven
Ali
0 °C.
WAITING
INTERLOCK
Signal interlocka prisoten na
konektorju P1 zaradi prekinitve
kratkega stika med pinom 3 in
pinom 8 konektorja J1, ali ker se je
odprl signal zunanjega interlocka.
PUMP
OVERTEMP.
CONTROLLER
OVERTEMP.
°C.
Temperatura controllera je presegla
70 °C.
Ali
Temperatura controllerskega
radiatorja je višja od 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Ponovno nastavite kratki stik
med pinom 3 in pinom 8
konektorja P1, ali zaprite
signal zunanjega interlocka.
vrne pod normalnim
vrednostnim pragom.
Pritisnite dvakrat tipko START
vrne pod normalnim
vrednostnim pragom. Dvakrat
pritisnite tipko START za
193/297
15
Obvestilo o napaki
OBVESTILO
OPIS
TOO HIGH
L0AD
programiranega.
POPRAVA
Preverite, da lahko rotor
pritisnite tipko START za
SHORT
CIRCUIT
Med navadnim delovanjem (po
zagonu) je priklopitev na izhodu v
kratkem stiku.
SYSTEM
OVERRIDE
zasilnosti iz oddaljenega kontakta.
controllera.
Dvakrat pritisnite tipko START
Izklopite napajalni kabel
controllera in popravite
napako, ki se je pojavila s
signalom zasile. Ponovno
pritisnite dvakrat tipko START
za ponoven
OVERVOLTAGE
POWER FAIL
194/297
Kvar v oddelku za napajanje
controllera, ali je controller dobil
nepristen znak.
controllera.
Dvakrat pritisnite tipko START
se to obvestilo spet pojavi,
obrnite se Agilent za pravilno
Obrnite se Agilent za pravilno
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
16
Instructions for Use
General Information
Storage
196
197
Preparation for Installation 198
Installation
Use
199
200
Controls, Indicators and Connectors 201
Front Panel Description 201
Use Procedure
203
Controller Startup 203
Starting the Pump 203
Pump Shutdown
Maintenance
203
Disposal
204
Error Messages
205
203
Original Instructions
195/297
16
Instructions for Use
General Information
General Information
This equipment is destined for use by professionals. The user should
read this instruction manual and any other additional information
supplied by Agilent before operating the equipment. Agilent will not be
held responsible for any events occurring due to non-compliance, even
partial, with these instructions, improper use by untrained persons,
non-authorised interference with the equipment or any action contrary
to that provided for by specific national standards.
The TwisTorr 84 -AG Rack controllers are micro-processor-controlled,
solid-state, frequency converter with self-diagnostic and self-protection
features.
Controller features:
Front / Remote / Serial Operation
24Vdc pump fan cooling drive
Vent valve drive
Pump speed reading after stop command (stop speed reading)
Pressure reading
Input voltage auto setting.
Profibus interface (optional)
The following paragraphs contain all the information necessary to
guarantee the safety of the operator when using the equipment. Detailed
information is supplied in the appendix "Technical Information".
196/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instructions for Use
Storage
16
This manual uses the following standard protocol:
WARNING!
The warning messages are for attracting the attention of the operator to a
particular procedure or practice which, if not followed correctly, could lead to
serious injury.
CAUTION!
The caution messages are displayed before procedures which, if not followed,
could cause damage to the equipment.
NOTE
The notes contain important information taken from the text.
Storage
When transporting and storing the controllers, the following
environmental requirements should be satisfied:
temperature: from -20 °C to + 70 °C
relative humidity: 0 – 95 % (without condensation)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
197/297
16
Instructions for Use
Preparation for Installation
Preparation for Installation
The controller is supplied in a special protective packing. If this
shows signs of damage which may have occurred during transport,
contact your local sales office. When unpacking the controller ensure
that it is not dropped or subjected to any form of impact. Do not
dispose of the packing materials in an unauthorized manner. The
material is 100 % recyclable and complies with EEC Directive 85/399.
Figure 1
198/297
Controller packing
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instructions for Use
Installation
16
Installation
WARNING!
The TwisTorr controller is designed for indoor use only and must be powered
with 3-wire power cord (see orderable parts table) and plug (internationally
approved) for user's safety. Use this power cord and plug in conjunction with
a properly grounded power socket to avoid electrical shock and to satisfy CE
requirements. High voltage developed in the controller can cause severe
injury or death. Before servicing the unit, disconnect the input power cable.
NOTE
The TwisTorr controller can be used as a bench unit or a rack module, but it
must be positioned so that free air can flow through the holes. Do not install or
use the controller in an environment exposed to atmospheric agents (rain, snow,
ice), dust, aggressive gases, or in explosive environments or those with a high
fire risk.
During operation, the following environmental conditions must be
respected:
temperature: from +5 °C to +45 °C;
relative humidity: 0 – 95 % (without condensation).
See the appendix “Technical Information” for detailed Information
about the above mentioned and the other connections, and about the
options installation.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
199/297
16
Instructions for Use
Use
Use
This paragraph describes the fundamental operating procedures.
Detailed information and operating procedures that envolve optional
connection or option are supplied in the paragraph “USE” of the
appendix “Technical Information”.
Make all vacuum manifold and electrical connections and refer to
TwisTorr pump instruction manual before operating the TwisTorr
controller.
WARNING!
NOTE
200/297
To avoid injury to personnel and damage to the equipment, if the pump is
laying on a table make sure it is steady. Never operate the TwisTorr pump if
the pump inlet is not connected to the system or blanked off.
The input signal J1 connector should be left in position including the shipping
links if no external connections are made. The forepump and TwisTorr pump can
be switched on at the same time.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instructions for Use
Use
16
Controls, Indicators and Connectors
The following paragraph illustrates the Controller control panel and
interconnection panel. More details are contained in the appendix
“Technical Information".
Front Panel Description
5
LS
AG
1
R1
R2
3
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
2
next
menu
previous
decrease
LOW SPEED
4
START/STOP
TwisTorr
84301-AG
FS AG
Turbo-V
Figure 2
Controller TwisTorr 84 -AG Front Panel
1
Keyboard push-button to recall on the display the cycle number, cycle time and pump life.
2
Keyboard push-button for LOW SPEED mode selection. It is active only when the front panel
operation has been selected. Pressed once, the pump runs at “stand-by” speed. To unselect
the mode, press the push-button again.
3
Keyboard push-button to recall on the display the pump current, pump temperature, pump
power and rotational speed. It is always active regardless of the operating mode selected.
Push-buttons 3 and 1, if pressed together for at least 2 seconds, put the controller in a routine
where it is possible to program some operation parameters.
4
Keyboard push-button for START, STOP/RESET mode selection. It is active only when the
front panel operation has been selected. By pressing once the starting phase begins; if
pressed again it stops the pump. If the pump has been stopped automatically by a fault, this
push-button must be pressed once to reset the controller and a second time to restart the pump.
5
LCD back-lighted alphanumeric display: dot matrix 2 lines x 16 characters.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
201/297
16
Instructions for Use
Use
8
7
6
1
2
5
3
Figure 3
4
Controller TwisTorr 84 -AG Rear panel
1
Logic input signals connectors (mating connector supplied with link).
2
Logic output signals connector and pump frequency monitor plus programmable analog
output.
3
Power output connector (24 Vdc for pump cooling fan, Vent Valve and Gauge).
4
Controller power entry module consisting of mains fuses, mains socket and EMC filter.
5
Rotary switches for Profibus address setting.
6
Profibus (Optional).
7
Remote control serial connector.
8
Pump cable (5m long).
202/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instructions for Use
Use Procedure
16
Use Procedure
Controller Startup
To startup the controller plug the power cable into a suitable power
source.
Starting the Pump
To start the pump, confirm the interlock input and press the START
pushbutton on the controller front panel.
Pump Shutdown
To shutdown the pump press the STOP push-button on the controller
front panel.
Maintenance
The TwisTorr 84 -AG Rack series controller does not require any
maintenance. Any work performed on the controller must be carried
out by authorized personnel.
When a fault has occurred it is possible to use the Agilent repair
service. Replacement controllers are available on an advance
exchange basis through Agilent.
WARNING!
Before carrying out any work on the controller, disconnect it from the supply.
If a pump is to be scrapped, it must be disposed off in accordance
with the specific national standards.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
203/297
16
Instructions for Use
Disposal
Disposal
Meaning of the "WEEE" logo found in labels
The following symbol is applied in accordance with the EC WEEE
(Waste Electrical and Electronic Equipment) Directive. This symbol
(valid only in countries of the European Community) indicates that
the product it applies to must NOT be disposed of together with
ordinary domestic or industrial waste but must be sent to a
differentiated waste collection system. The end user is therefore
invited to contact the supplier of the device, whether the Parent
Company or a retailer, to initiate the collection and disposal process
after checking the contractual terms and conditions of sale.
204/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Instructions for Use
Error Messages
16
Error Messages
For a certain type of failure, the controller will self-diagnose the
error and the messages described in the following table are
displayed.
Tab. 1
MESSAGE
DESCRIPTION
REPAIR ACTION
CHECK
CONNECTION
TO PUMP
Wrong connection between the
pump and the controller.
Check connection between
controller and pump.
Or
Press the START push-button
twice to start the pump.
The pump’s temperature is below 0
°C.
WAITING
INTERLOCK
The interlock signal of P1
connector is activated by an
interruption of the link between pin
3 and 8 of J1 connector, or
because the external interlock
signal is open.
Reset the short circuit
between pin 3 and pin 8 of P1
connector, or close the
external interlock signal.
PUMP
OVERTEMP.
The upper bearing/pump
temperature exceeds 60 °C.
Wait until the temperature
decrease below threshold
value.
Press the START push-button
twice to start the pump.
CONTROLLER
OVERTEMP.
The controller environment
temperature exceeds 70 °C.
Wait until the temperature
decrease below threshold
value.
Press the START push-button
twice to start the pump.
or
The controller’s radiator
temperature is above 60 °C.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
205/297
16
Instructions for Use
Error Messages
206/297
MESSAGE
DESCRIPTION
REPAIR ACTION
TOO HIGH
L0AD
The current drawn by the pump is
higher than programmed.
Check that the pump rotor is
free to rotate. Press the
START push-button twice to
start the pump.
SHORT
CIRCUIT
After the starting phase the output
connection is shorted.
Check connections and
shortages between pump and
controller. Press the START
push-button twice to start the
pump.
SYSTEM
OVERRIDE
The pump is stopped by an
emergency stop signal provided via
a remote contact.
Remove the controller power
cable and check the
emergency condition. Then
reconnect the power cable
and press the START pushbutton twice to start the
pump.
OVERVOLTAGE
Controller power supply circuitry is
faulty, or the Controller received a
spike.
Press the START push-button
twice to start the pump.
Should the message still be
present, call the Agilent
service.
POWER FAIL
Failure in the controller’s pump
power supply section.
Contact Agilent for
Maintenance.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
TwisTorr 84 FS AG Rack Controller User Manual
17
Technical Information
TwisTorr 84 Rack Controller Description
209
Controller Specifications 211
Controller Outline
212
Controller Connection
J6 – Fan
213
213
J7 – Vent 214
P1 – Input 215
J1 – Output
216
R1 – R2 Output Diagrams 220
Programmable Analog Output Diagrams
Pump Connector
222
223
J5 – Gauge Connector
223
Stop Speed Reading and Active Stop 226
J2 – Serial Connector
227
Connector Examples
228
Serial Communication Descriptions
Letter Protocol Description
Window Protocol
Description
229
230
236
236
Communication Protocol 236
Examples
239
Window Meanings 242
How to Use by Front Panel
247
Use 252
General
252
Startup
253
207/297
17
Technical Information
Error Messages
Programming
258
Configuration Menu 258
Mode Menu
260
Pump Setting Menu 261
Input/Output Menu 263
Setpoint R1 and Setpoint R2 Submenus
Gauge Menu
268
Serial Menu
270
How to Use by Remote I/0
271
How to Use in Serial Mode
271
266
Profibus Option 273
General
273
Installation273
Configuration 274
Software Operation and State Machine
274
Message Mapping 276
Parameter Buffer
277
Output Buffer 280
Input Buffer
281
Diagnostic Management 284
Diagnostic Buffer
286
Error Messages 288
Orderable Parts 291
208/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
TwisTorr 84 Rack Controller Description
17
TwisTorr 84 Rack Controller Description
The controller is available in three models (see orderable parts
table):
base version
with RS 232-485 option
with Profibus option
The controller is a solid-state frequency converter with the
following features:
Drives the pumps of the 84-NAV family.
Powers the pump cooling fan
Drives the vent valve.
Provides and acquires the pressure of the wide range gauge.
Remote I/Os compatible with the previous version.
Navigator default serial compatible with the previous RS 232
and 485 version.
Speed reading after stop command.
See the following diagram for the connections and orderable
parts.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
209/297
17
Technical Information
TwisTorr 84 Rack Controller Description
PUMP
AIR COOLING KIT
VENT VALVE
AIR COOLING KIT
EXTENTION CABLE
CONTROLLER
J2-SERIAL
J4-PROFIBUS
P1
IN
J1
OUT
LSD
PUMP
MSD
J6
TO POWER
SUPPLY
FAN
MAINS
FUSE TYPE T 4A
J7
VENT
J5
GAUGE
GAUGE CABLE (1 m)
GAUGE EXTENTION
CABLE (5 m)
Figure 4
210/297
MAINS CABLE
GAUGE
TwisTorr 84 -AG Rack Controller – Connections
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Controller Specifications
17
Controller Specifications
Tab. 2
Input:
Voltage
Frequency
Power
100, 240 Vac (voltage fluctuation +/- 10%)
50 to 60 Hz
450 VA
Fuse
2 x T4 A (slow blow) 250 V
Output:
NOTE
Voltage
Frequency
Power
75 Vac
1350 Hz
100 W (Ramp), 70 W (Normal and Autotuning)
Environment storage
-20 °C to +70 °C
0 – 95 %
Operating
+5 - +45 °C
0 – 90 %
Applied norr.
EN 61010 -1
EN 55011 (Class-A)
EN 61000-3-2,
EN 61000-3-3,
EN 61000-6-2,
EN 61000-4-2,3,4,5,6,11, 8
Weight:
1.7 Kg (3.2 lbs)
Pollution Degree
2
Installation Category
II
Acoustic noise (ISO7779)
LpA < 70 dB(A), normal operation, operator position
The Controller must be positioned in such way that the mains cable can be easily
disconnected.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
211/297
17
Technical Information
Controller Outline
Controller Outline
The outline dimensions for the TwisTorr 84 Rack Controllers are
shown in the following figure.
NOTE
The TwisTorr controller can be used as a bench unit or as a rack module, but it
must be positioned so that free air can flow through the holes.
9.4 [0.37]
106.4 [4.19]
91.4 [3.60]
=
=
1.5 [0.06]
=
=
128.5 [5.06]
122.5 [4.82]
8.5 [0.33]
110.6 [4.35 ]
LS
AG
R1
R2
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
next
menu
previous
decrease
LOW SPEED
START/STOP
TwisTorr
84 FS AG
Turbo-V 301-AG
96.1 [3.78]
244.0 [9.61]
Dimensions: mm [inches]
Figure 5
212/297
Controller outline
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Controller Connection
17
Controller Connection
J6 – Fan
The 24 Vdc, 150 mA maximum output voltage is present after
START pushbutton is pressed and will remain present until a
fault condition is displayed on front panel display or the
turbopump is stopped.
This is a dedicated output for the optional TwisTorr 84 pump
cooling fan (see orderable parts table).
If you already have fan installed, use the available adapter cable
to connect to the pump.
Figure 6
Fan Connector
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
213/297
17
Technical Information
Controller Connection
J7 – Vent
Figure 7
Vent Connector
This is dedicated 24 Vdc connector to control the optional vent
valve (see orderable parts table). The vent valve can be driven by
controller automatically or by serial line.
If you already have a vent valve installed 110 Vac powered, this
valve must be replaced by a new model (see orderable parts
table).
Vent Valve
CLOSED
OPEN
STOP
RAMP
START COMMAND
Figure 8
214/297
NORMAL
Vent Valve Relay
Win. 126
Vent Valve Open
Time Win. 147
STOP COMMAND
Vent Valve diagram in “Auto” mode
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Controller Connection
17
P1 – Input
Figure 9
P1 input connector
All the logic input to the controller must be connected at J1
mating connector. With the provided P1 mating connector
(shipped with pin 3 and pin 8 shorted) make the connections
with AWG 24, (0.24 mm2) or smaller wire to the pins indicated
in the figure to obtain the desired capability.
The following table describes the signals available on the
connector.
Tab. 3
Pins
Name
Description
Electrical
Note
1-com
Start/Stop
Contact closed = Start
Contact open = Stop
Optically isolated
Vlow, max = 10v
Imax = 5mA
Imin (on) = 2mA
Active only in
Remote Mode
operation
2-com
Low Speed
Contact closed = Low Speed
Contact open = High Speed
Optically isolated
Vlow, max = 10v
Imax = 5mA
Active only in
Remote Mode
operation
3-com
Interlock
Contact closed = Active
Contact open = Inactive
If active allows the pump running, if
inactive stops the pump.
Optically isolated
Vlow, max = 10v
Imax = 5mA
Imin (on) = 2mA
Active in all
modes
4-com
System
Override
Contact closed = Active
Contact open = Inactive
If active allows the pump running, if
active stops the pump and all the
others connected devices (Fan, Vent
Optically isolated
Vlow, max = 10v
Imax = 5mA
Imin (on) = 2mA
Active in all
modes
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
215/297
17
Technical Information
Controller Connection
Pins
Name
Description
Electrical
Note
Optically isolated
Vlow, max = 10v
Imax = 5mA
Imin (on) = 2mA
Active only in
Remote Mode
operation, and
in STOP
status.
Valve…).
5-com
Soft Start
Contact closed= Active
Contact open= Inactive
If active before the start command
activates the spft start procedure.
To be used only at first pump runup.
The following figure shows a typical contact logic input
connection and the related simplified circuit of the controller.
Figure 10
Typical logic input connection
J1 – Output
Figure 11
216/297
Logic output connector
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Controller Connection
17
All the logic output from the controller must be connected at P2
mating connector. The following table describes the signals
available on the connector.
The following figure shows a typical logic output connection
(relay coil) but any other device may be connected e.g. a LED, a
computer, etc., and the related simplified circuit of the
controller.
J1
+24 V
>1K
Figure 12
Digital Output Connection Example
1
2
Figure 13
Analog Output Connection Example
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
217/297
17
Technical Information
Controller Connection
Tab. 4
Pins
Name
Description
Electrical
Note
15-8
Fault
0V = no fail
Optically isolated
Vmax (=open) = 24v
Vlow, max = 1,5v
Connect a 10kohm
resistor between the
2 pins before
measuring voltage
A STOP command
(by front Panel or
serial or Start/stop
input) reset the FAIL
status.
24V = fail
Imax = 60mA
Pin-8 negative
Pin-15 positive
13-6
Start
Configurable output.
Default setting (win.177 = 0):
24V pump in RAMP state, 0V
= other state. If win.177 = 1:
0V = pump in stop or FAIL
status, 24V = other state
Optically isolated
Vmax (=open) = 24v
Vlow, max = 1,5v
Imax = 60mA
Pin-6 negative
Pin-13 positive
Connect a 10kohm
resistor between the
2 pins before
measuring voltage
12-5
Low Speed
24V = low speed active
0V = low speed not active
Optically isolated
Vmax (=open) = 24v
Vlow, max = 1,5v
Imax = 60mA
Pin-5 negative
Pin-12 positive
Connect a 10kohm
resistor between the
2 pins before
measuring voltage
11-4
R1
Programmable Set Point Out
can be related to: Frequency,
Power, Time Status or
Pressure.See following
figures for more details. All
the setting can be done by:
front panel or serial line
(win.101 to 105 and 162).
Optically isolated
Vmax (=open) = 24v
Vlow, max = 1,5v
Imax = 60mA
Pin-5 negative
Pin-12 positive
Connect a 10kohm
resistor between the
2 pins before
measuring voltage
14-7
R2
Programmable Set Point Out
Can be related to: Frequency,
Power, Time Status or
Pressure. See following
figures for more details. All
the setting can be done by:
front panel or serial line
(win.171 to 176).
Optically isolated
Vmax (=open) = 24v
Vlow, max = 1,5v
Imax = 60mA
Pin-7 negative
Pin-14 positive
Connect a 10kohm
resistor between the
2 pins before
measuring voltage
218/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Controller Connection
17
Pins
Name
Description
Electrical
Note
2-1
Programmable
Analog Output
Programmable analog output.
Can be related to : frequency,
power, pump temperature
(linear) or pressure
the external gauge.
The setting can be done by:
front panel or serial line
(win.111).
0V = 0Hz, 0W, 0°C
10V = 1350Hz, 70W, 100°C
See following chart for more
details
Optically isolated
Rload, min = 10kohm
Ripple Vpp,max =
200mV
Precision = 5%
Resolution = 40mV
Pin-1negative
Pin-2 positive
Connect a 100kohm
resistor between the
2 pins before
measuring voltage
9-1
Frequency
Analog Output
Analog output proportional to
frequency (linear).
0V = 0Hz
10V = 1010Hz
Optically isolated
Rload, min = 10k
Ripple Vpp,max =
200mV
Precision = 1%
Resolution = 40mV
Pin-1negative
Pin-9 positive
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
219/297
17
Technical Information
R1 – R2 Output Diagrams
R1 – R2 Output Diagrams
220/297
Figure 14
Diagram 1 – R1 or R2 related to frequency
Figure 15
Diagram 2 – R1 or R2 related to power
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
R1 – R2 Output Diagrams
Figure 16
17
Diagram 3 – R1 or R2 related to time
V (Volt)
R1-R2
24
0
Figure 17
Figure 18
Stop
Waiting
Interlock
Ramp
Auto
tuning
Braking
Normal
Fail
t (sec)
Diagram 4 – R1 or R2 related to Normal status
Diagram 5 – R1 or R2 related to pressure reading (if gauge
connected)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
221/297
17
Technical Information
Programmable Analog Output Diagrams
Programmable Analog Output Diagrams
V (Volt)
V (Volt)
Output
Voltage
10
0
Figure 19
freq.max
Frequency (Hz)
Diagram 1 – Programmable analog output related to frequency
(freq.max = 1010Hz)
V (Volt)
Output Voltage
10
0
Figure 20
150
Power (W)
Diagram 2 – Programmable analog output related to power
V (Volt)
Output Voltage
10
0
Figure 21
222/297
100
Pump Temp (°C)
Diagram 3 – Programmable analog output related to pump
temperature
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programmable Analog Output Diagrams
17
Pump Connector
A five-meter long cable is available to connect the controller to
the pump. The following figure shows the controller output
connector configuration where pins:
A-F = pump temperature sensor
B-C-D = 75 Vac 3-phase output to pump motor stator
E = EARTH PROTECTION
Figure 22
Controller-to-Pump Connector
J5 – Gauge Connector
This connector is available to connect
Agilent active gauges.
The controller recognizes automatically the gauge connected by
reading the signal “identification” in the connector.
Following a table with the gauge supported:
Gauge model
Name showed in the display
FRG 700/702
IMG 500
PVG 500/502
FRG 720/730
IM 500
CDG 500 T1000
CDG 500 T0100
CDG 500 T0010
CDG 500 T0001
FRGa
IMG
PVGa
FRGb
IM
CDG3
CDG2
CDG1
CDG0
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
223/297
17
Technical Information
Programmable Analog Output Diagrams
The controller give the error “gauge error” if the gauge connected is
not supported. The pressure can be read by dispaly or by serial line
(win. 224) or by REMOTE I/O on Programmable Analog Out.
If the Programmable Analog Output is related to the pressure
read by an external gauge, the controller doesn’t replicate
exactly the signal coming from the gauge; the controller converts
the gauge signal in the range from 0 to 10V.
The conversion formul is the following:
Vout
Vg Vg _ min
Vg _ max Vg _ min
10
Where:
Vg is the gauge output voltage;
Vout is the Analog Output voltage;
Vg_min ÷ Vg_max is the gauge voltage measuring range (these
values can be drawn from the gauge technical specifications).
Figure 23
224/297
Gauge Connector
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programmable Analog Output Diagrams
17
With the serial communication you can use the following
windows:
Win 224
XX
Pressure reading with the format X.X E
Win 257
Gauge status (read only):
0
when a gauge is not connected
Win 267
1
when a gauge is connected
2
when the pressure read is under
range or when the gauge give an
internal error
3
when the pressure read is under
range or when the gauge give an
internal error
4
when the “identification” is present
but not known by the controller
Gauge power (read/write):
If you need to turn off the gauge at
certain condition you can use this
window
0
gauge off
1
gauge on (default)
2
gauge normally off. It turns on when
the set point 1 is activated. If the set
point 1 type (win 101) is selected as
“pressure” the gauge is always on.
3
gauge normally off. It turns on when
the set point 1 is activated. If the set
point 2 type (win 171) is selected as
“pressure” the gauge is always on.
4
gauge normally off. It turns on when
the set point 1 is activated. If the set
point 3 type (win 101) is selected as
“pressure” the gauge is always on.
The windows from 136 to 140 manage an additional set point
(set point 3) dedicated to turn ON or OFF the gauge (win 267=4)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
225/297
17
Technical Information
Programmable Analog Output Diagrams
Pump Driving
Typical pump driving chart start and normal operation.
160
1200
140
1000
120
Frequency (Hz)
80
600
60
Freq. (Hz)
400
Power (W)
100
800
40
Power. (W)
20
200
0
0
0
50
100
150
200
300
250
350
- 20
400
Time (s)
Figure 24
Diagram 4
Stop Speed Reading and Active Stop
This functions can be activated by Front Panel or serial line
(Win 107, 167).
Active Stop brakes the pump using the motor. The Stop Speed
reading reads the pump speed after a stop command.
SSR
Figure 25
226/297
AS
Diagram 5
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
J2 – Serial Connector
17
J2 – Serial Connector
This connector provides the connection for RS – 232 and RS –
485 serial line.
J2 Pin-out:
Figure 26
J2 Connector
Tab. 5
PIN N.
SIGNAL NAME
1
+5 V (OUT) (Reserved)
2
TX (RS232
3
RX (RS232
4
NC
5
GND
6
A + (RS485)
7
NC
8
B – (RS485)
9
RESERVED
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
227/297
17
Technical Information
J2 – Serial Connector
Connector Examples
PC
228/297
5
5
2
2
3
3
Figure 27
RS – 232 Connection
Figure 28
RS – 485 Connection
TwisTorr 84 FS AG
Rack Controller
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
J2 – Serial Connector
17
The communication port mating connector is supplied with the
RS 232 PCB (AMP/Cannon or equivalent 15-pin "D" type male
connector). For example, the Transmit data signal from
controller (pin 2) must be connected to the host computer's
receive data line (pin 2) and vice versa. Consult the host
computer's instruction manual for its serial port connections.
NOTE
Agilent cannot guarantee compliance with FCC regulations for radiated
emissions unless all external wiring is shielded, with the shield being
terminated to the metal shroud on the 0-subconnector. The cable should be
secured to the connector with screws.
Serial Communication Descriptions
This unit can comunicate by two different protocol:
protocol (old system) “letter”
“Window” protocol (new system)
These two protocols can be used as well with 232 or 485 media.
NOTE
Please use “Window” protocol for new development.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
229/297
17
Technical Information
Letter Protocol Description
Letter Protocol Description
The default protocol is “Window”
Communication format:
8 data bit
no parity
1 stop bit
The baud rate is programmable via front panel from 600 to
9600 baud. The controller is factory-set for 9600 baud
operation.
Communication protocol:
Host = Master
Controller = Slave
The communication is performed in the following way:
Host
Controller
Request is an ASCII character identifying the action that must
be performed by the controller or the requested information.
Allowed ASCII characters:
"A" = START
"B" = STOP
"C" = Low Speed ON
"D" = Low Speed OFF
"E" = Request for operational parameters
"F" = Pump times zeroing
230/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Letter Protocol Description
17
"G" = Parameters reading
"H" = Parameters writing
"I" = Request for operating status
"J" = Request for numerical reading
"K" = Request for counters reading.
CRC corresponds to the sum (with inverted sign) of all the
preceding bytes.
e.g., the START command "A" in ASCII code = 41 inverted it will
be: FF + 1 - 41 = BF.
Tab. 6
CHARACTER
ASCII
CONVERTED ASCII FOR CRC CALCULATION
"A"
41h
-
CRC
-
BFh
"B"
42h
-
CRC
-
BEh
"C"
43h
-
CRC
-
BDh
"D"
44h
-
CRC
-
BCh
"E"
45h
-
CRC
-
BBh
"F"
46h
-
CRC
-
BAh
"G"
47h
-
CRC
-
89h
"H"
48h
-
"I "
49h
-
CRC
-
B7h
"J"
4Ah
-
CRC
-
B6h
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
231/297
17
Technical Information
Letter Protocol Description
CHARACTER
ASCII
CONVERTED ASCII FOR CRC CALCULATION
"K"
4Bh
-
CRC
-
B5h
"ACK"
06h
-
CRC
-
FAh
"NACK"
15h
-
CRC
-
EBh
Answer = after a request from the host, the Controller will
answer in one of the following ways:
ACK
NACK
Message
When the Request is "A, "B”, "C", "D", "F" the Controller will
Answer the ACK or NACK.
When the Request is "E, the Answer will contain the complete
set of the following parameters:
Tab. 7
BYTES
MEANING
1
MSB
LSB
--XXX
0 = STOP
1 = WAITING INTERLOCK
2 = STARTING
3 = NORMAL OPERATION
4, 5 = HIGH LOAD
6 = FAILURE
7 = APPROACHING LOW SPEED
232/297
2÷5
Cycle Time
6÷9
Pump Life
10÷11
Pump Temperature
12
Current*
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Letter Protocol Description
BYTES
MEANING
13
Voltage*
14÷17
Frequency
18÷19
Cycle #
20
R1 Status
21
R2 Status
22
CRC
17
*The values for current and voltage are given as numbers, scaled
from 0 to 255, where 0 corresponds to 0 V and 255 to the full
scale voltage (130 V) or current (2,5 A).
When the Request is "G", the Answer will contain a string of 11
characters with the following parameters:
Tab. 8
BYTES
MEANING
1-2
Pump cycles number (integer coded in 2 bytes)
3
Speed threshold
4-7
Run up time in seconds (long coded in 4 bytes)
8
Deat time (0 = NO 1 = YES)
9
Reserved
10
Soft Start mode (0 = NO 1=YES)
11
CRC
When the configuration parameters have to be changed, send a
Request string with "H" characters of the following type:
"H" + .... data .... + CRC
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
233/297
17
Technical Information
Letter Protocol Description
The following parameters can be changed:
Tab. 9
BYTES
MEANING
1
Speed threshold
2-5
Run up time in seconds (long coded in 4 bytes)
6
Deat time (0 = NO 1 = YES)
7
Reserved
8
Soft Start mode (0 = YES 1 = NO)
9
CRC
When the Request is "I" (Status readings), the Answer will
contain a string of 2 characters with the following parameters:
Tab. 10
BYTES
MEANING
1
MSB
LSB
--XXXXXX
0 = STOP
1 = WAITING INTERLOCK
2 = STARTING
3 = NORMAL OPERATION
4, 5 = HIGH LOAD
6 = FAILURE
7 = APPROACHING LOW SPEED
R2 status 0 = OFF 1 = ON
R1 status 0 = OFF 1 = ON
2
234/297
CRC
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Letter Protocol Description
17
When the Request is "J" (Numerical readings), the Answer will
contain a string of 5 characters with the following parameters:
Tab. 11
BYTES
MEANING
1
Current (0-255 scaled)
2
Voltage (0-255 scaled)
3
Rotational speed KRPM
4
Pump temperature °C (0-254 temperature reading, 255 =
fail)
5
CRC
When the Request is "K" (Counters readings), the Answer will
contain a string of 11 characters with the following parameters:
Tab. 12
BYTES
MEANING
1-4
Cycle time
5-8
Pump life
9-10
Cycle number
11
CRC
On request a sample program in QBasic language is available by
Agilent.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
235/297
17
Technical Information
Letter Protocol Description
Window Protocol
Description
Communication Format
8 data bit
no parity
1 stop bit
baud rate: 600/1200/2400/4800/9600 programmable
Communication Protocol
The communication protocol is a MASTER/SLAVE type where:
Host = MASTER
Controller = SLAVE
The communication is performed in the following way:
1
the host (MASTER) send a MESSAGE + CRC to the controller
(SLAVE);
2
the controller answer with an ANSWER + CRC to the host.
The MESSAGE is a string with the following format:
<STX>+<ADDR>+<WIN>+<COM>+<DATA>+<ETX>+<CRC>
Where:
NOTE
236/297
When a data is indicated between two quotes (‘...’) it means that the indicated
data is the corresponding ASCII character.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Letter Protocol Description
17
<STX> (Start of transmission) = 0x02
<ADDR> (Unit address) = 0x80 (for RS 232)
<ADDR> (Unit address) = 0x80 + device number (0 to 31)
(for RS 485)
<WIN> (Window) = a string of 3 numeric character indicating the
window number (from ‘000’ to ‘999’); for the meaning of each
window see the relevant paragraph.
<COM> (Command) = 0x30 to read the window, 0x31 to write
into the window
<DATA> = an alphanumeric ASCII string with the data to be
written into the window. In case of a reading command this field
is not present. The field length is variable according to the data
type as per the following table:
Tab. 13
Data Type
Field Length
Valid Characters
Logic (L)
1
‘0’ = OFF
‘1’ = ON
Numeric (N)
6
‘-‘, ‘.’, ‘0’ . . . ‘9’ right justified with ‘0’
Alphanumeric (A)
10
from blank to ‘_’ (ASCII)
<ETX> (End of transmission) = 0x03
<CRC> = XOR of all characters subsequent to <STX> and
including the <ETX> terminator. The value is hexadecimal coded
and indicated by two ASCII character.
The addressed SLAVE will respond with an ANSWER whose
structure depends from the MESSAGE type. When the MESSAGE
is a reading command, the SLAVE will respond transmitting a
string with the same structure of the MESSAGE.
NOTE
Using the RS 485 interface, the message structure remains identical to the one
used for the RS 232 interface, the only difference being that the value assigned
to the ADDRESS <ADDR>
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
237/297
17
Technical Information
Letter Protocol Description
The controller can answers with the following response types:
Tab. 14
238/297
Response Type
Response
Length
Response
Value
Description
Logic
1 byte
-
after a read instruction of a logic
window
Numeric
6 bytes
-
after a read instruction of a
numeric window
Alphanumeric
10 bytes
-
after a read instruction of an
alphanumeric window
ACK
1 byte
(0x6)
the command execution has been
successfully completed
NACK
1 byte
(0x15)
the command execution has been
failed
Unknown Window
1 byte
(0x32)
the specified window in the
command is not a valid window
Data Type Error
1 byte
(0x33)
the data type specified in the
command (Logic, Numeric or
Alphanumeric) is not accorded with
the specified Window
Out of Range
1 byte
(0x34)
the value expressed during a write
command is out of the range value
of the specified window
Win Disabled
1 byte
(0x35)
the specified window is Read Only
or temporarily disabled (for
example you can’t write the Soft
Start when the Pump is running)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Examples
17
Examples
Command: START
Source: PC
Destination: Controller
02
80
STX
ADDR
30
30
30
WINDOW
31
31
03
WR
ON
ETX
42
31
30
03
42
WR
OFF
ETX
CRC
33
CRC
Source: Controller
Destination: PC
02
80
06
03
38
STX
ADDR
ACK
ETX
CRC
35
Command: STOP
Source: PC
Destination: Controller
02
80
30
30
STX
ADDR
WINDOW
30
32
Source: Controller
Destination: PC
02
80
06
03
38
STX
ADDR
ACK
ETX
CRC
35
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
239/297
17
Technical Information
Examples
Command: SOFT-START (ON)
Source: PC
Destination: Controller
02
80
STX
ADDR
31
30
30
WINDOW
31
31
03
WR
ON
ETX
42
32
CRC
Source: Controller
Destination: PC
02
80
06
03
38
STX
ADDR
ACK
ETX
CRC
35
Command: SOFT-START (OFF)
Source: PC
Destination: Controller
02
80
STX
ADDR
31
30
30
WINDOW
31
30
03
WR
OFF
ETX
42
33
CRC
Source: Controller
Destination: PC
240/297
02
80
06
03
38
STX
ADDR
ACK
ETX
CRC
35
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Examples
17
Command: READ PUMP STATUS
Source: PC
Destination: Controller (with address = 3)
02
STX
83
ADDR
32 30 35
WINDOW
30
RD
03
ETX
38 37
CRC
Source: Controller (with address = 3 in stop status)
Destination: PC
02
83
ST
X
ADD
R
3
2
3
0
3
5
3
0
3
0
WINDOW
3
0
3
0
3
0
3
0
03
DATA (STATUS)
ET
X
3
8
3
7
CRC
Command: REAL SERIAL TYPE
Source: PC
Destination: Controller (with address = 3 in 485 mode)
02
83
STX
ADDR
35
30
34
WINDOW
30
03
RD
ETX
38
31
CRC
Source: Controller
Destination: PC
02
STX
83
ADDR
35 30 34
WINDOW
30
RD
31
DATA
03
ETX
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
42
30
CRC
241/297
17
Technical Information
Examples
Window Meanings
Tab. 15
Accessories and Spare Parts
N.
Read/
Write
Data
Type
Description
Admitted Values
000
R/W
L
Start/Stop (in remote/ Front mode the
window is a read only)
Start = 1
Stop = 0
001
R/W
L
Low Speed Activation
No = 0
Yes = 1 (default = 0)
008
R/W
L
Remote (default) or Serial configuration
Remote = 1
Serial = 0 (default = 1)
100
R/W
L
Soft Start (write only in Stop condition)
YES = 1
NO = 0
101
R/W
N
R1 Set Point type
0 = Frequency
1 = Power
2 = Time
3 = Normal (default = 3)
4 =Pressure (available only if
the gauge is connected)
102
R/W
N
R1 Set Point valve (expressed in Hz, W or s)
(default = 900)
103
R/W
N
Set Point delay: time between the pump
start and the set point check (seconds)
0 to 99999 (default = 0)
104
R/W
L
Set Point signal activation type: the signal
can be "high level active" or "low level
active"
0 = high level active
1 = low level active
(default = 0)
105
R/W
N
Set point hysteresis (in % of value)
0 to 100 (default = 2)
106
R/W
L
Water cooling
0 = NO
1 = YES
107
R/W
L
Active Stop (write only in stop)
0 = NO
1 = YES
108
R/W
N
Baud rate
600 = 0
1200 = 1
2400 = 2
4800 = 3
9600 = 4
(default = 4)
242/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Examples
109
W
L
Pump life/ cycle time/ cycle number
reset
To reset write ‘1’
110
R/W
L
Interlock type (default = 0)
111
R/W
L
Analog output type: output voltage signal
proportional to frequency power
Impulse = 0
Continuous = 1
0 = frequency
1 = power
(default = 1)
2 = Pump temperature
3 = Pressure
117
R/W
N
Low Speed frequency (Hz)
120
R/W
N
Rotational frequency setting (Hz)
122
R/W
L
Set vent valve on/off (on = closed)
123
124
125
Reserved to Agilent service
R/W
L
126
R/W
N
Set the vent valve operation
130
136
Vent valve opening delay (expressed in 0.2
sec)
Reserved to Agilent service
R/W
N
Gauge Set Point Type
137
138
139
R/W
R/W
R/W
N
N
L
Gauge Set Point Value (Hz, W, s)
Gauge Set Point Mask (sec)
Gauge Set Point Segnal Activation Type
140
R/W
N
143
R/W
N
Gauge Set front Mysteresis (in % of R2
Valve)
External Fan Configuration
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
17
Low speed
frequency (win 117)
to 1 0
(default = 1 0)
On = 1
Off = 0 (default = 1)
Automatic = 0 (see note 1.)
On command = 1 (see note
2.)
0 to 65535 (corresponding to
0 to 13107 sec)
0 = Freq
1 = Power
2 = Time
3 = Normal (default)
(default (867)
(default = 0)
Ø = high level active
(default)
1 = low level active
(default = 2)
0 = ON
1 = automatic
2 = serial
(default = 2)
243/297
17
Technical Information
Examples
144
R/W
L
External Fan Activation
147
R/W
N
155
R
N
157
R/W
N
162
R/W
A
163
R/W
N
Vent open time
See “vent connector” paragraph
Power limit applied
Read the maximun power deliverable
to the pump
Gas load type.
Select the gas load to the pump
R1 Set Point Pressure Threshold
Valid if min. 101 = 4
Format X.X E XX
Where X = 0 to 9 s = + or Pressure unit of measure
167
R/W
A
171
R/W
N
Stop speed reading
Activates / deactivates the pump speed
reading after Stop command
R2 Set Point Type
172
173
174
R/W
R/W
R/W
N
N
L
R2 Set Point Value (Hz, W, s)
R2 Set Point Mask (sec)
R2 Set Point Signal Activation Type
175
176
R/W
R
N
A
177
R/W
L
R2 Set Point hysteresis (in % of R2 Valve)
R2 Set Point Pressure Threshold
Valid if win 171 = 4
Format X.X E XX
Where: X= 0 to 9
s = + or Start Output Mode
244/297
0 = OFF
1 = ON
(default = 0)
0 = infinite
1 bit = 0.2 sec
watt
Ø = N2
1 = Av
0 = mBar
1 = Pa
2 = Torr
0 = disable
1 = enable
0 = Freq
1 = Power
2 = Time
3 = Normal (default = 3)
4 =Pressure (available only if
the gauge is connected)
Ø = high level active
1 = low level active
0 = Starting (Output ON
only with pump
Status = Starting)
1 = running (Output ON
when the pump
is running) (default)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Examples
181
R/W
N
Gas type
182
200
201
202
R/W
R
R
R
N
N
N
N
203
204
205
R
R
R
N
N
N
Gas correction
Pump current in mA dc
Pump voltage in Vdc
Pump power in W (pump current x pump
voltage duty cycle)
Driving frequency in Hz
Pump temperature in °C
Pump status
206
R
N
Error code
211
216
R
R
N
N
Controller Heatsink Temperature (°C)
Controller Air Temperature (°C).
224
R
A
Pressure reading Format = X.X E XX
226
R
N
Rotation Frequency (rpm)
257
R
N
Gauge status
17
0 = not configured
1 = Nitrogen
2 = Argon
3 = Idrogen
4 =other
0 to 70
Stop = 0
Waiting intlk = 1
Starting = 2
Auto-tuning = 3
Braking = 4
Normal = 5
Fail = 6
Bit description: see the
following figure
0 = No gauge connected
1 = gauge connected
2 = Under range/gauge error
3 = over range/gauge error
4 = Rid unknown
267
R/W
N
Gauge power
0 = gauge off
1 = gauge 0n
2 = programmable power sp1
3 = programmable power sp2
4 = programmable power sp3
300
R
N
Cycle time in minutes (zeroed by the reset
command)
0 to 999999
301
R
N
Cycle number (zeroed by the reset
command)
0 to 9999
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
245/297
17
Technical Information
Examples
302
R
320
to 399
Reserved to Agilent service
400
R
A
CRC EPROM (QE)
QE8XXXX (where “XXXX”
are variable)
402
R
A
CRC Param. (PA)
PA8XXXX (where “XXXX”
are variable)
404
R
A
CRC Parameter structure
"XXXX"
500
Reserved to Agilent service
503
R/W
N
RS 485 address
0 to 31 (default = 0)
504
R/W
L
Serial type select
0 = RS 232
1 = RS 485 (default = 0)
NOTE
N
Pump life in hours (zeroed by the reset
command)
0 to 999999
1. Automatic means that when the controller stops, the vent valve is opened
with a delay defined by window n. 126; when the controller starts, the vent
valve is immediately closed.
2. On command means that the vent valve is opened or closed by means of
window n. 122.
7
6
5
4
3
2
1
TOO HIGH LOAD
NO CONNECTION
SHORT CIRCUIT
PUMP OVERTEMP.
OVERVOLTAGE
AUX FAIL
Figure 29
246/297
0
CONTROLL. OVERTEMP.
POWER FAIL
Window N. 206 Bit Description
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
How to Use by Front Panel
17
How to Use by Front Panel
LS
R1
AG
R2
VACUUM TECHNOLOGIES
MEASURES
COUNTERS
increase
next
menu
previous
decrease
LOW SPEED
START/STOP
TwisTorr
84 FS AG
Turbo-V
301-AG
Figure 30
Start Stop and Reset Fail button
Press once for the START command and again for the STOP
command. In the case of controller’s failure, press once to
reset the fail condition.
NOTE
The front panel START/STOP function is available only if the controller is set to
“FRONT mode”. If it is set to “REMOTE mode”, when the key is pressed an error
message is shown indicating “COMMAND LOCKED IN REMOTE”, if it is set to
“SERIAL” mode, the “COMMAND LOCKED IN SERIAL MODE” error message is
displayed. The “Reset Fail” function is always available regardless of controller
mode.
Low Speed
Press once to activate the LOW SPEED command; press
again to de-activate.
NOTE
The front panel LOW SPEED function is available only if the controller is set to
“FRONT”; otherwise an error message is returned. If it is set to “REMOTE”
mode, the COMMAND LOCKED IN REMOTE error message is displayed while if
it is in “SERIAL” mode the “COMMAND LOCKED IN SERIAL MODE” error
message is returned.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
247/297
17
Technical Information
How to Use by Front Panel
Counters
Pressing the first time on the display, the following
information is displayed:
T
C
Y
C
I
M
E
L
E
X
X
X
X
X
X
X
X
X
m
Where:
CYCLE XXXX
Number of start/stop cycles
TIME
Time of last cycle (minutes)
XXXXXm
Pressing a second time, the following is displayed:
P
U
M
P
X
X
X
X
L
I
F
X
X
h
E
PUMP LIFE
XXXXXX
total operating time (hours) of the pump
Pressing a third time, the following message Is displayed:
M
N
:
X
X
X
X
X
X
X
X
X
X
S
N
:
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
MN
Model Number of the controller
SN
Serial Number
On pressing the key again, the main screen page is redisplayed.
Measures
Pressing once, the following is obtained:
P
=
X
X
X
W
T
X
=
X
X
°
X
X
X
H
z
C
Where:
P = XXX W is the current power supplied to the pump
248/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
How to Use by Front Panel
17
T = XX °C is the current temperature of the pump
XXXX Hz is the current frequency of rotation of the pump. This
value is set by default to 963 Hz but can be modified by the user
according to needs, proceeding as described in the
“PROGRAMMING” paragraph. The unit of measurement (HZ /
Krpm, default = Hz) is selected by the user from the
INPUT/OUTPUT->SPED menu.
If the SOFT-START function (PUMP SETTING menu ’
SOFTSTART is active and the pump is ramping, indication of the
speed of rotation is replaced with a bar-graph that indicates the
soft-start step in course and the total number of steps to be
performed. On completion of the soft-start ramp, the bar-graph
is replaced with indication of the frequency of rotation of the
pump
Pressing twice, the following is obtained:
N
O
R
M
A
L
I
=
X
.
X
X
A
V
X
X
X
X
H
z
=
X
X
X
V
H
z
Z
Where:
NORMAL: indicates the operating regime of the pump
XXXHz: see description “Pressing once” Measures key
I=X.XXA: indicates the current absorbed by the pump
V= XXX V: indicates the pump driving voltage
Pressing 3 times, the following is obtained:
P
X
=
X
X
X
W
X
.
X
X
E
-
Y
.
X
E
-
Y
Y
m
B
P
=
X
X
X
W
X
X
X
X
Y
m
B
a
R
a
r
Z
Z
Z
X
X
X
H
z
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
X
249/297
17
Technical Information
How to Use by Front Panel
Where:
P= XXXW: indicates the current power supplied to the pump
XXXHz: see description “Pressing once” Measures key
X.XE-YYmBar: indicates the pressure currently measured by the
gauge.
ZZZZ: indicates the kind of gauge (see table of gauge supported
in the gauge chapter)
Other possible indications:
P
=
X
X
X
W
G
A
U
G
E
E
R
X
X
X
X
H
z
R
O
R
X
X
X
X
H
z
U
N
D
E
R
Where:
GAUGE_ERROR: gauge not connected or broken
P
=
X
X
X
W
P
R
E
S
S
U
R
E
Where:
PRESS UNDER: indicates that the pressure read is below the
minimum measurement threshold set (5 E-9 mBar)
P
=
X
X
X
W
P
R
E
S
S
U
R
E
X
X
X
X
O
V
E
R
H
z
Where:
PRESS OVER: indicates that the pressure measured is above the
maximum measurement threshold set (1000 mBar)
The unit of measurement of the pressure can be selected
(GAUGE menu’ Unit) from “mBar”,”Pa”,”torr”
Pressing 4 times returns to the following screen page:
N
250/297
O
R
M
A
L
X
X
X
X
X
X
X
X
X
X
X
X
X
H
X
X
X
X
X
z
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
How to Use by Front Panel
17
Where:
NORMAL: indicates the operating regime of the pump
XXXHz: see description “Pressing once” Measures key
The operating mode of the controller is shown at the bottom in
the center. This may be:
FRONT: front mode (the controller accepts START/STOP and
LOW SPEED commands from the front panel)
REMOTE: remote mode (the controller accepts START/STOP
and LOW SPEED commands via the rear connector)
RS232: the controller accepts commands from the serial port
according to the RS232 standard.
RS485 [XX]: the controller accepts commands from the serial
port in RS485 mode with address XX (XX from 0 to 31)
PROFIBUS [YYY]: the controller accepts commands from the
PROFIBUS port with address YYYY
Black rectangles as shown below may be displayed at any time
in the first and last box of the bottom line of the display
(opposite the LS / AG / R1 / R2 captions). The meaning of these
rectangles is as follows:
LS ’ the controller is at LOW SPEED
AG ’ the Gauge is connected to the controller
R1 ’ relay (set point) R1 is active
R2 ’ relay (set point) R2 is active
LS
AG
R1
R2
Figure 31
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
251/297
17
Technical Information
Use
Use
General
Make all vacuum manifold and electrical connections and refer
to TwisTorr pump instruction manual before to operating the
TwisTorr controller.
WARNING!
NOTE
252/297
To avoid injury to personnel and damage to the equipment, if the pump is laying
on a table make sure it is steady. Never operate the TwisTorr pump if the pump
inlet is not connected to the system or blanked off.
The input signal P1 connector should be left in position including the shipping
links if no external connections are made. The forepump and the TwisTorr pump
can be switched on at the same time.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Use
17
Startup
Plug the controller power cable into a suitable power source.
The display lights up for approx. 2 seconds and shows:
A
U
T
O
T
O
K
E
S
T
After 2 seconds, the display shows the following screen page:
S
T
O
P
.
F
NOTE
R
O
N
.
.
.
H
z
O
N
H
z
T
If the pump is not connected, the display will be as follows:
C
H
E
C
K
C
O
N
N
T
O
P
U
M
P
E
C
T
I
Pressing the START button, the pump is started and the
display shows the following screen page.
S
T
A
R
T
I
N
G
F
R
O
X
N
X.
X
X
T
R1
R2
LS
AG
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
next
menu
previous
decrease
LOW SPEED
START/STOP
TwisTorr
84301-AG
FS AG
Turbo-V
Figure 32
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
253/297
17
Technical Information
Use
This screen page will be visible throughout the acceleration
phase the pump. The increasing value of the rotation frequency
will be displayed in the boxes marked X; the user may decide to
express this value in Hz (default) or in KRMP.
Once operating speed has been reached, the following screen
page is displayed:
N
O
R
M
A
L
9.
F
R
O
N
6
3
H
z
T
If the LOW SPEED key is pressed, the above screen page changes
to:
B
R
A
K
I
N
G
F
R
X
O
N
X
X
X
H
z
T
R1
R2
LS
AG
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
next
menu
previous
decrease
LOW SPEED
START/STOP
TwisTorr
84 301-AG
FS AG
Turbo-V
Figure 33
The following screen page is displayed on reaching the preestablished speed:
254/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Use
N
O
R
M
A
L
9
F
R
O
N
0
0
17
H
z
H
z
T
The rotation value set in both NORMAL and LOW SPEED mode
can be modified by the user as described in the Programming
section of this manual.
Press the MEASURES push button: the display shows:
P
=
5
0
W
9
T
=
4
5
°
6
3
C
R1
R2
LS
AG
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
next
menu
previous
decrease
LOW SPEED
START/STOP
TwisTorr
84301-AG
FS AG
Turbo-V
Figure 34
Where:
P = is the DC power drawn by the pump (range 0 to 999 Watt)
Hz = is the rotational speed of the pump as a function of the
controller output frequency
°C = is the temperature of the outer ring of the upper bearing
(range 00 to 99 °C)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
255/297
17
Technical Information
Use
Pressing MEASURES key twice, the following screen page is
displayed:
N
O
R
M
A
L
I
=
1
.
2
9
0
A
V
=
6
3
H
4
2
V
z
Where:
I is the current supplied by the controller to the pump at that
precise moment.
V is the voltage at which the controller is powering the pump at
that moment
Pressing the MEASURES key three times, with the GAUGE
connected and functioning, the following screen page is
displayed:
7
.
4
P
=
E
-
0
5
5
0
W
m
B
A
r
1
0
LS
AG
1
X
X
X
0
H
z
X
R1
R2
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
next
menu
previous
decrease
START/STOP
LOW SPEED
TwisTorr
FS AG
Turbo-V84
301-AG
Figure 35
Where:
mBar shows the pressure value measured
XXXX shows the kind of gauge connected
256/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Use
17
The following messages may be displayed instead of the
pressure:
GAUGE ERROR: indicates that the GAUGE is not identified
PRESSURE UNDER: indicates that a pressure below the
minimum threshold set has been measured
PRESSURE OVER: indicates that a pressure exceeding the
maximum threshold set has been measured
Pressing the COUNTERS key, the following is obtained:
T
C
Y
C
I
M
E
L
E
X
X
X
X
X
X
X
X
X
m
R1
R2
LS
AG
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
next
menu
previous
decrease
LOW SPEED
START/STOP
TwisTorr
84301-AG
FS AG
Turbo-V
Figure 36
Where:
CYCLE XXXX
TIME XXXXXm
Pressing again:
P
Number of start/stop cycles
Time of last cycle (minutes)
U
M
P
X
X
X
X
L
I
F
X
X
h
E
Where:
PUMP LIFE
pump
XXXXXX
total operating time (hours)of the
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
257/297
17
Technical Information
Programming
Programming
Configuration Menu
To access the configuration menu, press the COUNTERS +
MEASURES buttons at the same time for at least 2 sec.
LS
R1
AG
R2
VACUUM TECHNOLOGIES
COUNTERS
MEASURES
increase
next
menu
previous
decrease
START/STOP
LOW SPEED
TwisTorr
84301-AG
FS AG
Turbo-V
Figure 37
In programming mode, the meaning of the 4 buttons changes as
follows:
COUNTERS/LOW SPEED speed become “INCREASE and
DECREASE” and make it possible to select the next or
previous value of a parameter (in the case of compulsory
parameters) or to increase/decrease the individual digit of a
parameter (in the case of numeric parameters)
The “MEASURES and START/STOP” buttons become
“NEXT and PREVIOUS” and make it possible to select the
next parameter (or next digit of a numeric parameter) or
previous parameter.
258/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programming
17
Switching from one parameter to the next (using the “NEXT”
key) indicates confirmation of any changes made to the specific
parameter. If the changes cannot be accepted by the controller,
the “Data out of limits” error message is displayed, the changes
are cancelled and the value of the parameter prior to the
modification is reproposed.
Switching from a parameter to the previous parameter (using
the “PREVIOUS” key) indicates the intention to abort any
changes made to the specific parameter. Abort is indicated by
the caption “Changes aborted” that is displayed for approx. 1
second before moving to the previous parameter.
The configuration environment has a tree-like structure and
permits “circular” navigation; on reaching the end of a branch,
the user is returned automatically to the start of this. Navigation
can proceed in a forwards (NEXT button) or backwards
(PREVIOUS button) direction
It is possible to enter a sub-branch by pressing the “INCREASE”
button. If no buttons are pressed for more than 1 minute, the
controller automatically quits the programming environment
canceling any modifications made to the current parameter.
The figure below shows the first level of the configuration menu
and the links to the respective second level menus (indicated
below).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
259/297
17
Technical Information
Programming
FRONT
MODE
REMOTE
SERIAL
PUMP SETTING
HIGH SPEED ADJ
PROFIBUS
F. 2
START MODE
INPUT / OUTPUT
F. 3
SETPOINT
R1 SETTING
R1/R2 TRESHOLD
F. 4
SETPOINT
R2 SETTING
PRESSURE UNIT
GAUGE
F. 5
BAUD RATE
SERIAL
F. 6
Flow 1/6
Figure 38
Mode Menu
MODE: permits selection (see Flow 1/6) of the operating
mode of the controller from those indicated below:
FRONT: accepts commands from the front panel
REMOTE: accepts commands from the remote input
connector
SERIAL: accepts commands from the serial interface (or
Profibus interface if present)
PROFIBUS: this operating mode is present only if the
Profibus interface is installed on the controller
260/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programming
17
Pump Setting Menu
PUMP SETTING
F. 1
HIGH SPEED ADJ
[Hz]
0000
LOW SPEED ADJ
[Hz]
0000
9999
SOFT START
Only Front Mode
Configuration
EXTERNAL FAN CNF
YES
9999
NO
ALWAYS ON
OFF_LIMPOWER
SERIAL
VENT VALVE MODE
AUTO TIME
MANUAL
AUTO PUMP SPEED
0000
VENT VALVE DELAY
VENT OPEN TIME
0=NO LIMIT
0000
9999
LOAD GAS TYPE
Argon
9999
Air
WATER COOLING
YES
NO
ACTIVE STOP
YES
NO
STOP SPEED
READING
YES
NO
Flow 2/6
Figure 39
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
261/297
17
Technical Information
Programming
This menu contains all the parameters that have a direct effect
on driving of the pump.
HIGH SPEED: Sets (in Hz) the speed of rotation of the pump
when the low-speed function is not active.
LOW SPEED: Sets (in Hz) the speed of rotation of the pump
when the low-speed function is active.
SOFT START: enables (YES) or disables (NO) the soft start
function. This parameter is visible only if the controller is
configured in FRONT mode.
EXTERNAL FAN CNF: Makes it possible to select driving
mode of the external cooling fan. Possible options:
ALWAYS ON: the cooling fan is always ON
OFF_LIMPOWER: 10 seconds after the pump has
reached NORMAL status, the fan is switched off and the
driving power of the pump is reduced to 50 W
SERIAL: the cooling fan is controlled directly via the
serial port.
VENT VALVE MODE: makes it possible to select driving of
the vent valve
AUTO TIME: the valve is controlled by the controller
MANUAL: the valve is controlled by the serial port.
AUTO PUMP SPEED: the valve is controlled by the
controller its king into account the pump’s deceleration.
VENT VALVE DELAY: Sets the delay, expressed in seconds,
between stopping of the pump and opening of the vent valve.
VENT VALVE OPEN TIME: sets the time, expressed in
seconds, of opening of the vent valve. Enter 0 if the valve is
to be kept open indefinitely (until the next start).
LOAD GAS TYPE: selects the type of gas used in the
process. Therefore, the controller limits the power supplied
to the pump according to the setting of this parameter.
WATER COOLING: indicates whether the pump is cooled
with water or not. The controller limits the power supplied
to the pump according to this setting.
262/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programming
17
ACTIVE STOP: enables (YES) or disables (NO) active
braking.
STOP SPEED READING: enables (YES) or disables (NO) the
pump rotational frequency reading function also during the
slowing phase that follows a stop command
Input/Output Menu
This menu contains parameters that determine the operating
mode of the inputs and outputs of the controller.
IMPUT / OPTPUT
START - INTERLOCK
START MODE
F. 1
START/STOP LEVEL
START/STOP EDGE
INTERLOCK TYPE
CONTINUOUS
IMPULSIVE
ANALOG OUT TYPE
FREQUENCY
POWER
CURRENT
PRESSURE
START OUT MODE
RUNNING
STARTING
SPEED DISPLAY
KRPM
Hz
LCD CONTRAST
0
7
Flow 3/6
Figure 40
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
263/297
17
Technical Information
Programming
START MODE: Permits selection of one of the three types of
functioning of the START/STOP and INTERLOCK inputs:
START/INTERLOCK: The pump is started if the
START/STOP input is activated and is stopped if the
START/STOP input is de-activated. The interlock input
must be constantly active (INTERLOCK TYPE parameter
= continuous) or may be active only at the time of
starting (INTERLOCK TYPE parameter = impulsive)
START/STOP LEVEL The START/STOP input acts as
only START command (active on the level) The
INTERLOCK input acts as STOP command (active on the
level).
In the case of concurrent activation of the two inputs,
the STOP command takes priority
START/STOP EDGE The START/STOP input acts as
START command (active on the edge)
The INTERLOCK input acts as STOP command (active
on the edge).
INTERLOCK TYPE: This parameter is displayed only when
the previous parameter (START MODE) is equal to
START/INTERLOCK and permits selection of one of the
following two operating modes of the INTERLOCK input:
CONTINUOUS: the INTERLOCK input must be active
continuously so that the pump can be driven by the
controller. If, with the controller in start, the input
INTERLOCK is de-activated, the controller switches to
WAITING INTERLOCK status and interrupts driving of
the pump
IMPULSIVE: it is sufficient for the input to be active
when the START command is sent to the pump.
Subsequently, the input can also be de-activated. If the
interlock is not active when the pump is started, the
controller switches too WAITING INTERLOCK status.
264/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programming
17
ANALOG OUT TYPE: permits selection of the type of signal
to be sent to the programmable analogue output. One of the
following signals can be selected:
FREQUENCY: the drive frequency of the pump is shown
POWER: the power supplied to the pump is shown
TEMPERATURE: the temperature of the pump is shown
PRESSURE: the pressure read by the gauge is shown.
START OUT MODE: Selects the operating mode of the
START output. Possible options:
RUNNING: the output is active when the pump is driven
STARTING: the output is active only during acceleration
ramp-up.
SPEED OUT MODE (KRPM/Hz): permits selection of the
unit of measurement of the speed of rotation shown on the
display of the controller.
This setting acts only on the measurement shown on the
display. Possible options:
KRPM
Hz
LCD CONTRAST
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
265/297
17
Technical Information
Programming
Setpoint R1 and Setpoint R2 Submenus
This submenu contains the settings relating to the output with
relay R1 and R2 (if it is connected a gauge it will present also the
settings for the set point 3).
SET POINT
R1/R2 SETTING
R1/R2 TYPE
FREQUENCY
F. 1
POWER
TIME
NORMAL
PRESSURE
R1/R2 SET VALUE
XX
0000
9999
R1/R2 HYSTERESYS
%
00
99
R1/R2 MASK TIME
00:00:00 SEC
00:00:00
99:99:99
R1/R2 OUTPUT
LOGIC: _|--
_|--
--|_
Flow 4/6
Figure 41
266/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programming
17
R1 (R2) TYPE: selects the type of reference measurement to
drive the relay. Possible types:
Frequency: driving frequency of the pump
Power: power supplied to the pump
Time: time from start
Normal: achievement of normal condition
Pressure: pressure read by the gauge, if present
R1 (R2) SET VALUE: Sets the reference value at which the
relay R1 (R2) is activated. This parameter is not available if
TIME or NORMAL (previous parameter) is selected as
SETPOINT TYPE.
R1 (R2) HISTERESYS: Sets, in percentage, the hysteresis of
the relay
R1 (R2) MASK TIME: sets the masked time (in hh:mm:ss),
measured from start, within which the SETPOINT R1 (R2) is
not driven even if the threshold value has been reached. This
parameter is not available if SETPOINT TYPE is set to
NORMAL
R1 (R2) OUTPUT LOGIC: Selects the control logic of the
SETPOINT output.
positive logic (the relay is energized when the
measurement exceeds the reference)
negative logic (the relay is energized when the
measurement is below the reference)
This parameter is not available if SETPOINT TYPE is set to TIME
or NORMAL.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
267/297
17
Technical Information
Programming
Gauge Menu
This menu contains the parameters relating to functioning of the
active gauge.
PRESSURE UNIT
GAUGE
mbar
F. 1
Pascal
Torr
GAS CORRECTION
01
02
99
Flow 5/6
Figure 42
268/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Programming
17
PRESSURE UNIT: selects the unit of measurement of the
pressure used to show this on the display, for display on the
serial line and for setting of the setpoint and autopressure
thresholds. Possible options:
mbar
Pascal
Torr
GAUGE MODEL ID: it shows the gauge model identified by the
controller.
If there are more model with the same identification the user
can select the right gauge connected
GAS TYPE : sets the gas type:
0 : not configured
1 : Nitrogen
2 : Argon
3 : Idrogen
4 : Other
CORRECTION : if it is selected the gas type 4 (Other) you
can set the correction factor of the pressure measurement
for this kind of gas. The pressure indicated by the
instrument is equal to:
P indicated = P measured x Gas correction / 10
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
269/297
17
Technical Information
Programming
Serial Menu
This menu contains the settings for management of the
RS232/485 serial line.
SERIAL
BAUD RATE
600
F. 1
1200
4800
9600
SERIAL MODE
RS232
RS485
SERIAL ADDRESS
00
01
31
Flow 6/6
Figure 43
BAUD RATE: permits selection of the communication speed
selecting this from 600, 1200, 4800, 9600 baud
SERIAL MODE: permits setting of the type of interface to
RS232 (point to point) or RS485 (multidrop)
SERIAL ADDRESS: sets the address of the node in the case
of the RS485 interface. This parameter is not visible if the
RS232 is selected.
270/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
How to Use by Remote I/0
17
How to Use by Remote I/0
1
Power ON the controller
2
Press the “COUNTERS” and “MEASURES” button toghether.
3
Select MODE = REMOTE from the “INPUT/OUTPUT” menu
4
Exit from configuration menu
5
Connection example:
How to Use in Serial Mode
1
Power on the controller
2
Connect the serial cable
3
Select by front panel if you want to work in 232 or 485, and
if necessary, the serial address.
4
Select SERIAL from the INPUT/OUTPUT menu
5
Open the T+ software (see orderable parts table)
6
Ready to operate by SERIAL connections.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
271/297
17
Technical Information
How to Use in Serial Mode
Open = High Speed
Cloed = Low Speed
Open = Stop
Cloed = Start
Controller
Start/Stop
1
2
3
4
5
6
7
8
9
Imput
Connector
Low Speed
Interlock
System Override
Soft Start
Closed = Stop
Open = Allow Start
Open = Normal Start
Cloed = Soft Start
Output
Connector
4 K7
Fault (+24 VDC) 15
Fault
OFF = OK
ON = Fail
8
4 K7
Start (+24 VDC) 13
Start
OFF = Stop, Normal Operation
ON = Ramp
6
4 K7
Low Speed (+24 VDC) 12
Low Speed
5
R2, R1(+ 24 VDC)14,
11
R2, R1
OFF = High speed
ON = Low speed setted
4 K7
OFF = Pump under speed threshold
ON = Pump over speed threshold
7, 4
Pump Power
Monitor (10V=150W)
2
Monitor (Com)
1
Pump Frequency
Monitor (10V=81 KRPM)
9
v
Power value
v
Speed value
Figure 44
272/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Profibus Option
17
Profibus Option
General
The ProfiBus option allow to communicate with the controller as
ProfiBus DP slave device.
The option works as a bi-directional bridge between the ProfiBus
network and the Agilent turbo controller internal link. The
interface provides input data (measures) and output data
(commands) to the controller, and in addiction provides
standard and user related diagnostics, in order to allow the user
to manage the exceptions.
Installation
This option is factory installed.
The ProfiBus connector pin-out is reported in the following
figure. Please in order to obtain best performance use ProfiBus
certified cables.
Figure 45
ProfiBus connector
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
273/297
17
Technical Information
Profibus Option
Configuration
Before power-on the controller set the ProfiBus address by the 2
rotary switches.
Up to 126 different addresses (from 0 to 125) can be selected.
The address value sets by the 2 switches is expressed in
hexadecimal notation, so value from 00 to 7D are permitted; this
setting is read by the interface during the power-on phase, so
any change of the switch position after the power-on is ignored.
Software Operation and State Machine
From the software point of view, the interface can be seen as
two devices (one for ProfiBus and the other for the internal link)
linked together.
Each device has its own state machine to manage the device
operation.
Figure 46
Tab. 16
274/297
Profibus state machine
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Profibus Option
Status
Meaning
POWER_ON
Interface set-up
WAIT_PRM
Wait for parameterisation from the master
WAIT_CFG
Wait for configuration from the master
DATA_EX
Regular data exchange
17
Figure 47
Tab. 17
Internal link state machine
Status
Meaning
POWER_ON
Interface set-up
SRC_ADDR
Search for the controller serial address
IDENTIFY
Identify controller model and protocol
DATA_EX
Regular data exchange
The two machines continuously share I/O data with the relative
bus, and interact each other only in following conditions:
ProfiBus Data Exchange is suspended (static diagnosis
activated) if the internal serial link in not established
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
275/297
17
Technical Information
Profibus Option
Internal serial link Data Exchange is suspended (only for
output data) if the ProfiBus State machine is not in Data
Exchange mode
As a general rule, unrecoverable communication errors make
each machine to jump to the state immediately following the
power-on state (WAIT_PRM or SRC_ADDR).
Message Mapping
The communication is based on the continuous data exchange
capability of the ProfiBus standard, where the master sends
continuously the entire slave configuration and reads back the
entire slave status.
For this purpose one Input (from slave to master) and one
Output (from master to slave) buffers are provided. All the
needed parameters are mapped inside each buffer.
The following tables summarise the ProfiBus parameter access,
related to the corresponding windows serial protocol (for this
protocol please refers to the serial interface paragraph).
The interface doesn’t any scaling operation on the read/written
parameters. It acts only as a gateway between the ProfiBus
network and the pump’s controller serial interface. As a
consequence of this, the scale and the meaning of some
parameters depends directly to the specific model of Turbo
Pump controller connected to the interface.
276/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Profibus Option
17
Parameter Buffer
Tab. 18 Parameter buffer
OFFSET
BYTE
SIZE
BYTE
UNIT RES
RANGE
DESCRIPTION
0
1
-
0-99
Gauge gas load type. The value is divided by 10
(entering 12 the controller will apply 1.2)
Enter here the correction factor for gas (necessary
only if gauge is connected).
161
1
2
mA/Hz/sec
0-10000
Setpoint 1 value. Enter here the threshold value for
the R1 output, valid only if B0-B2 of Parameter
Buffer Offset-21 is equal to 0,1,2 or 3.
102
3
2
Sec
0-30000
Setpoint 1 Mask Time. Set here the time, measured
from the start pump event, while the R1 output is
masked (not activated)
103
5
2
mA/Hz/sec
0-10000
Setpoint 2 value. Enter here the threshold value for
the R2 output, valid only if B3-B5 of Parameter
Buffer Offset-21 is equal to 0,1,2 or 3.
172
7
2
Sec
0-30000
Setpoint 2 Mask Time. Set here the time, measured
from the start pump event, while the R2 output is
masked (not activated)
173
9
2
0.2sec/bit
0-30000
126
Vent Valve Opening Delay.
Set the delay time between the stop command and
vent opening. Valid only in “purge/vent auto mode”
(Parameter Buffer, Offset 20, B0 = 0). 0 = infinite
(the valve will never open).
11
2
0.2sec/bit
0-30000
Vent Valve Open Time. Set how long the vent will
remain open, then both purge and vent will be
closed. Valid only in “purge/vent auto mode”
(Parameter Buffer, Offset 20, B0 = 0). 0 = infinite
(the valve remain open till next start command).
147
13
1
%
1-99
Setpoint 1 Hysteresis. Set the Setpoint1 hysteresis
around the nominal value
105
14
1
%
1-99
Setpoint 2 Hysteresis. Set the Setpoint2 hysteresis
around the nominal value
175
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
WIN
SERIAL
277/297
17
Technical Information
Profibus Option
15
1
16
1
17
1
18
1
19
1
mBar/Torr/P 0-99
a
-10 - +10
mBar/Torr/P 0-99
a
-10 - +10
Setpoint 1 Pressure Value Mantissa.
Set the mantissa of the exponential value of the R1
setpoint (format X.XE-XX) when it is used for
pressure monitoring (Parameter Buffer, Offset 21,
B0-2 = 4). The value set here is divided by 10, that
means 11 = 1.1
162
Setpoint 1 Pressure Value Exponent.
Set the exponent of the exponential value of the R1
setpoint (format X.XE-XX) when it is used for
pressure monitoring (Parameter Buffer, Offset 21,
B0-2 = 4).
162
Setpoint 2 Pressure Value Mantissa.
Set the mantissa of the exponential value of the R2
setpoint (format X.XE-XX) when it is used for
pressure monitoring (Parameter Buffer, Offset 21,
B3-5 = 4). The value set here is divided by 10, that
means 11 = 1.1
176
Setpoint 2 Pressure Value Exponent.
Set the exponent of the exponential value of the R2
setpoint (format X.XE-XX) when it is used for
pressure monitoring (Parameter Buffer, Offset 21,
B3-5 = 4).
176
B0= Stop Speed Reading.
167
This function measures the pump speed after a stop
command.
0 = Off
1 = On
B1= Active Stop.
This function brakes the pump after a stop
command, by using the motor as a generator.
0 = Off
1 = On
107
B2 - Reserved
B3-4 = Start/Stop/Interlock Mode.
151
Change the logic of Start/Stop and Interlock inputs.
Ask to Agilent personnel for this option
278/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Profibus Option
20
21
1
1
B0 = Vent & Purge Auto/Man
0 = Auto (the controller drives purge and vent
valves automatically)
1 = Manual (the user can command the valves by
serial line or profibus)
B1 = Gas Load Type. Select here the gas load
0 = Ar
1 = N2
B2 = Interlock Type
0 = continuos (the interlock must be always present
to run the pump)
1 = at start (the interlock must be present only at
start command)
B3 = Setpoint R1 Logic
0 = active close (NO)
1 = active open (NC)
B4 = Setpoint R2 Logic
0 = active close (NO)
1 = active open (NC)
B5-6 = Pressure Unit
0 = mbar
1 = Pascal
2 = Torr
B7 = Reserved
B0-2 = Setpoint R1 Type
0 = frequency
1 = current
2 = time
3= normal operation
4= pressure
B3-5 = Setpoint R2 Type
0 = frequency
1 = current
2 = time
3= normal operation
4= pressure
B6-7 = Analog Output 1 Type
0 = frequency
1 = power
2 = temperature
3= pressure
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
17
125
157
110
104
174
163
101
171
111
279/297
17
Technical Information
Profibus Option
Output Buffer
Tab. 19 Output buffer
Offset
Byte
0
Size
Byte
1
Unit Res
1
2
Hz
3
2
Hz
280/297
Range
Description
1100 1350
1100 1350
B7 = Start/Stop
0 = Stop, 1 = Start
B6 = Low Speed
This bit set the pump target speed to “low speed
value” (Output Buffer, Offset 3), otherwise the
target speed is set to “high speed value” (Output
Buffer, Offset 1).
0 =Off, 1 =On
B5 – Soft Start
This bit activates the soft start function which runup the pump smoothly. Please activate this function
only if the pump has been stopped for at least3
months.
0 = On, 1= Off
B4 = Vent Valve Command
0 = Close, 1 = Open
Valid only if in Par Buff, Offset-20, B0=1
B3 = Purge Valve Command
0 = Close, 1 = Open
Valid only if Par Buff, Offset-20, B0=1
B2 – Not used
B0-1 = Operating Mode
These bits define from which source the controller
has to get commands (readings are always
available). In order to operate the controller by
Profibus these bits must be set to 3.
0 = Remote I/O
1 = Serial
2 = Front panel
3 = Profibus
High Speed Value
Set the high rotational speed value
Low Speed Value
Set the low rotational speed value
WIN
Serial
000
001
100
122
145
008
120
117
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Profibus Option
17
Input Buffer
Tab. 20 Input buffer
OFFSET
BYTE
SIZE
BYTE
UNIT RES
RANGE
DESCRIPTION
0
1
V
0-100
Voltage
Voltage provided to the motor
1
1
°C
0-100
Pump Bearing Temperature
204
Read the pump upper bearing temperature
If > 60 °C the controller goes into fail status and the
pump is stopped
2
1
°C
0-100
Controller Power Supply Temperature
Read the controller power section temperature if >
75 °C the controller goes in fail status “controller
over-temperature”
216
3
1
°C
0-100
Controller CPU Section Temperature
Read the controller CPU section temperature if
> 80 °C the controller goes in fail “controller
overtemperature”
211
4
1
-
0-6
B0-3 – Status
205
0 = Stop
1= Waiting for interlock (interlock connections on
remote I/O connector missing)
2 = Ramp (the pump is increasing the speed)
3 = Auto tuning (the speed has been reduced
because the gas load is higher than the Power Limit
Applied)
4 = Braking (the pump is reducing the speed using
the motor)
5 = Normal operation (the pump is at target speed)
6 = Fail (see error code byte Input Buffer Byte-27)
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
WIN
SERIAL
201
281/297
17
Technical Information
Profibus Option
5
1
-
-
Error Code (bit field)
206
B7 – Too High Load (the gas load is too high for the
pump)
B6 – Short Circuit (a short circuit happened between
the two of the three motor phases)
B5 – Over Voltage (too high bus voltage during
braking)
B4 – Verify Line Select
Not used
B3 – Power Fail (internal circuitry failure)
B2 – Controller Over-Temperature (“Controller
Power Section Temperature” or “Controller CPU
Section Temperature” are over the limit)
B1 - Pump Over-Temperature (“Pump Bearing
Temperature” or “Pump Body Temperature” are
over the limit)
B0 – Check Connection To Pump (the connection
between controller and pump missing)
6
1
-
-
B0 – Set Point R1 Status
0 = open
1 = closed
221
B1 – Set Point R2 Status
0 = open
1 = closed
225
B2 – Vent Valve Status
0 = closed
1 = open
122
B3 – Purge Valve Status
0 = close
1 = open
145
B4 – Not Used
B5 – Not Used
B6 – Not Used
B7 – Not Used
282/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Profibus Option
17
7
2
mA
0-10000
Current
Motor current consumption
200
9
2
W
0-200
Power
Motor power adsorption
202
11
2
W
0-200
Power Limit Applied
Maximum allowable power
155
13
2
Hz
0-1500
Driving Frequency
Read the rotational speed of the pump
203
15
2
Hz
0-1500
Target Frequency
Read the target rotational speed
120
17
2
-
0-65536
Cycle Number
301
Number of cycles (start and stop) done by the pump
19
2
min
0-65536
Last Cycle Time
How long the last cycle lasted
300
21
2
h
0-65536
Pump Life
Total pump running time
302
23
4
mBar/Torr/
Pa
-
Pressure Reading
Reports the pressure reading in the “pressure unit”
selected by Par. Buff., Offset-20, B5-6
224
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
283/297
17
Technical Information
Profibus Option
Diagnostic Management
In addition to the ProfiBus six byte standard diagnostic, the
interface provides both user diagnostic and static diagnostics
functions
The standard diagnostic management is fully compliant with the
ProfiBus specification.
During the start-up phase after power on, the first byte in the
user diagnostic area, can assume values different from zero.
This byte has the following meaning:
Bit 0 = 1: controller not responds (RS485 link broken)
Bit 1 = 1: controller not identified (not compatible with the
ProfiBus gateway)
Bit 2 = 1: first loop of requests not ended (values in the input
data are not fully coherent yet)
So, if the first byte is equal to 0, the interface is working
properly, otherwise there is a problem.
284/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Profibus Option
17
Each nibble in the bytes following the interface status byte
represents the status of the last attempt to write a parameter
with following coding (diag status byte):
0
Write success
1
Controller response was “NACK”
2
Controller response was “Unknown window”
3
Controller response was “Bad Data Type”
4
Controller response was “Over range”
5
Controller response was “Bad operation”
6
Controller response was an unknown response
F
Parameter not supported by the controller
The ProfiBus external diagnosis services are used to report
following unexpected situations:
Controller fail: if the controller goes in fail mode, an
external diagnostic service is required and one byte in the
diagnostic buffer signals the type of failure.
User parameter mismatch: if the user sets one or more
parameters out of their allowed range, a ProfiBus external
diagnostic service is required and some bits in the diagnosis
frame signals which parameter is wrong (i.e. over range or
under range).
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
285/297
17
Technical Information
Profibus Option
Diagnostic Buffer
286/297
Diagnostic buffer
OFF SET
MEANING
0
B0
B1
B2
B3
B4
B5
B6
B7
station non exist (set by master)
station not ready (slave not ready for data exchange)
cfg fault (configuration data doesn’t match)
ext diag (slave has external diagnostic data)
not supported (slave doesn’t support requested function)
invalid slave response ( slave sets permanent ‘0’)
prm fault (wrong parameter assignment)
master_lock (slave is parameterised by another master)
1
B0
B1
B2
B3
B4
B5
B6
B7
prm req (slave has to be re-parameterised)
stat diag (static diagnosis)
fixed ‘1’
wd_on (response monitoring active)
Freeze mode (received freeze command)
Synch mode (received synch command)
reserved
diag deactivated (slave is parameterised by another master)
2
Reserved
3
Master Add (master address after parameterisation. FF= without
parameter)
4
Ident number high
5
Ident number low
6
External diagnosis “Header” length indication including header
Standard diagnostic
Tab. 21
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
OFF SET
MEANING
7
Interface Status
Controller not responds
B0
Controller not identified
B1
B2
Input data not fully coherent yet
Not used
B3
B4-7 Not used
8
B7-4 – Start/Stop diag status
B3-0 – Low Speed diag status
9
B7-4 – Soft Start diag status
B3-0 – Vent Valve
10
B7-4 – Purge Valve
B3-0 – Mode
11
B7-4 – High speed
B3-0 – Low Speed
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
17
External diagnostic
Technical Information
Profibus Option
287/297
17
Technical Information
Error Messages
Error Messages
For a certain type of failure, the controller will self-diagnose the
error and the following messages will be displayed.
NOTE
If the pump is not connected, the display will be as shown in the following
figure.
C
H
E
C
K
C
O
N
N
T
O
P
U
M
P
E
C
T
I
O
N
Check connection between controller and pump, then press
STOP push-button twice to start the pump.
NOTE
If the P1 input connector is not in position with the link or the external interlock
connections are open, when the START pushbutton is pressed the display will
be as shown in the following figure.
I
W
A
I
T
I
N
G
N
T
E
R
L
O
C
K
Disconnect connector P1 and check the link or the external
interlock, then install the connector to start the pump.
NOTE
288/297
If within each step of the soft start mode the rotational speed of the pump do
not reach the planned value within 15 minutes the display will be as shown in
the following figure.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Error Messages
NOTE
17
If in normal operation (after the starting phase) the current drawn by the pump
is higher than programmed (1.8 A), the pump and the inter-connected devices
are switched off and the display will be as shown in the following figure.
T
O
O
H
I
G
H
L
O
A
D
Verify that systems has no leaks than press STOP RESET
pushbutton twice to start the pump.
Check that pump rotor is free to rotate then press the STOP
RESET pushbutton twice to start the pump.
NOTE
If the upper bearing/pump temperature exceeds 60 °C, the pump is shut off, and
the display will be as shown in the following figure.
O
V
P
U
M
P
E
R
T
E
M
P
The message will stay on until the temperature decreases below
threshold value. Press the STOP RESET pushbutton twice to
start the pump.
NOTE
If the controller transformer temperature exceeds 90°C, the pump is shut off,
and the display will be as shown in the following figure.
C
O
N
T
R
O
L
L
E
O
V
E
R
T
E
M
P
R
The message will stay on until the temperature decreases below
threshold value. Press the STOP RESET pushbutton twice to
start the pump.
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
289/297
17
Technical Information
Error Messages
P
O
W
E
R
F
A
I
L
Indicates a fault in the circuit of the controller used to power the
pump.
NOTE
If the pump is stopped by an emergency stop signal provided via a remote
contact, the display will be as shown in the following figure.
O
S
Y
S
T
E
M
V
E
R
R
I
D
E
Remove the controller power cable and check the emergency
condition.
Then reconnect the power cable and press the START
pushbutton to start the pump.
O
V
E
R
V
O
L
T
A
G
E
Controller power supply circuitry is faulty, or the Controller
received a spike.
Press the START push-button twice to start the pump. Should
the message still be present, call the Agilent service.
S
H
O
R
T
C
I
R
C
U
I
T
Check connections and shortages between pump and controller,
then press the STOP RESET pushbutton twice to start the pump.
290/297
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
Technical Information
Orderable Parts
17
Orderable Parts
Tab. 22
Description
Part number
TwisTorr 84 FS AG Rack Controller with RS-232/485
TwisTorr 84 FS AG Rack Controller with Profibus
option
X3508 64001
X3506 4002
Turbo-V 81 – AG Nav Air cooling kit (0.5m)
9699290
Turbo-V 81 – AG Nav Air cooling kit Extension cable
(5m)
9699940
Vent Valve N.O. 0,5 mm orifice (0,5 m cable)
9699844
Vent Valve extention cable (5 m)
9699941
Mains cable NEMA plug (3 m)
9699958
Mains cable european plug (3 m)
9699957
TwisTorr 84 FS AG Rack Controller User Manual / 87-901-037-01 (A)
291/297
Vacuum Products Division
Dear Customer,
Thank you for purchasing an Agilent vacuum product. At Agilent Vacuum Products
Division we make every effort to ensure that you will be satisfied with the product and/or
service you have purchased.
As part of our Continuous Improvement effort, we ask that you report to us any problem
you may have had with the purchase or operation of our products. On the back side you find a
Corrective Action request form that you may fill out in the first part and return to us.
This form is intended to supplement normal lines of communications and to resolve
problems that existing systems are not addressing in an adequate or timely manner.
Upon receipt of your Corrective Action Request we will determine the Root Cause of the
problem and take the necessary actions to eliminate it. You will be contacted by one of our
employees who will review the problem with you and update you, with the second part of the
same form, on our actions.
Your business is very important to us. Please, take the time and let us know how we can
improve.
Sincerely.
Giampaolo LEVI
Vice President and General Manager
Agilent Vacuum Products Division
Note: Fax or mail the Customer Request for Action (see backside page) to Agilent Vacuum Products Division (Torino) – Quality
Assurance or to your nearest Agilent representative for onward transmission to the same address.
CUSTOMER REQUEST FOR CORRECTIVE / PREVENTIVE / IMPROVEMENT ACTION
TO:
AGILENT VACUUM PRODUCTS DIVISION TORINO – QUALITY ASSURANCE FAX
N°:
XXXX-011-9979350
ADDRESS:
AGILENT TECHNOLOGIES ITALIA S.p.A. – Vacuum Products Division –
Via F.lli Varian, 54 – 10040 Leinì (TO) – Italy
E-MAIL:
[email protected]
NAME
COMPANY
FUNCTION
ADDRESS:
TEL. N° :
FAX N° :
E-MAIL:
PROBLEM / SUGGESTION :
REFERENCE INFORMATION (model n°, serial n°, ordering information, time to failure after installation, etc.):
DATE
CORRECTIVE ACTION PLAN / ACTUATION
(by AGILENT VPD)
LOG N°
XXX = Code for dialing Italy from your country (es. 01139 from USA; 00139 from Japan, etc.)
Vacuum Products Division
Instructions for returning products
Dear Customer,
Please follow these instructions whenever one of our products needs to be returned.
Complete the attached Request for Return form and send it to Agilent Technologies (see below), taking particular
care to include the completed Health and Safety declaration Section. No work can be started on your unit until we
receive a completed copy of this form.
After evaluating the information, Agilent Technologies will provide you with a Return Authorization (RA) number via
email or fax, as requested. Note: Depending on the type of return, a Purchase Order may be required at the time the Request
for Return is submitted. We will quote any necessary services (evaluation, repair, special cleaning, eg).
Product preparation
o
o
o
o
o
o
o
Remove all accessories from the core product (e.g. inlet screens, vent valves).
Prior to shipment and if applicable for your product, drain any oils or other liquids, purge or flush all gasses, and
wipe off any excess residue.
If ordering an Advance Exchange product, please use the packaging from the Advance Exchange to return the
defective product.
Seal the product in a plastic bag, and package product carefully to avoid damage in transit. You are responsible
for loss or damage in transit.
Include a copy of the Health and Safety Declaration in the shipping documentation on the outside of the shipping
box of your returning product.
Clearly label package with RA number. Using the shipping label provided will ensure the proper address and RA
number are on the package. Packages shipped to Agilent without a RA clearly written on the outside cannot be
accepted and will be returned.
Return only products for which the RA was issued.
Shipping
o
o
Ship to the location specified on the printable label, which will be sent, along with the RA number, as soon as
we have received all of the required information. Customer is responsible for freight charges on returning
product.
Return shipments must comply with all applicable Shipping Regulations (IATA, DOT, ADR, etc.) and carrier
requirements.
RETURN THE COMPLETED REQUEST FOR RETURN FORM TO YOUR NEAREST LOCATION:
EUROPE:
Fax:
Fax Free:
Toll Free:
00 39 011 9979 330
00 800 345 345 00
00 800 234 234 00
[email protected]
NORTH AMERICA:
Fax:
Toll Free:
1 781 860 9252
800 882 7426, Option 3
[email protected]
Page of
PACIFIC RIM:
Please visit our website for
individual office information
http://www.agilent.com
Agilent VPD Request for Return
Vacuum Products Division
Terms and conditions
TERMS AND CONDITIONS
Please read the terms and conditions below as they apply to all returns and are in addition to the Agilent Technologies
Vacuum Product Division – Products and Services Terms of Sale.
o
Unless otherwise pre-negotiated, customer is responsible for the freight charges for the returning product.
Return shipments must comply with all applicable Shipping Regulations (IATA, DOT, etc.) and carrier
requirements.
o
Agilent Technologies is not responsible for returning customer provided packaging or containers.
o
Customers receiving an Advance Exchange product agree to return the defective, rebuildable part to Agilent
Technologies within 15 business days. Failure to do so, or returning a non-rebuildable part (crashed), will result
in an invoice for the non-returned/non-rebuildable part.
o
Returns for credit toward the purchase of new or refurbished Products are subject to prior Agilent approval and
may incur a restocking fee. Please reference the original purchase order number.
o
Units returned for evaluation will be evaluated, and a quote for repair will be issued. If you choose to have the
unit repaired, the cost of the evaluation will be deducted from the final repair pricing. A Purchase Order for the
final repair price should be issued within 3 weeks of quotation date. Units without a Purchase Order for repair
will be returned to the customer, and the evaluation fee will be invoiced.
o
Products returned that have not been drained from oil will be disposed.
o
A Special Cleaning fee will apply to all exposed products.
o
If requesting a calibration service, units must be functionally capable of being calibrated.
Page of
Agilent VPD Request for Return
Vacuum Products Division
Request for Return Form
Customer information
Company :
Address:
Contact Name:
Tel:
Email:
Fax:
Agilent Serial No
Original Purchasing Reference
Equipment
Product description
Agilent PartNo
Failure description
Type of process (for which the equipment was used)
Type of return
Non Billable
Billable
Exchange
Repair
New PO # (hard copy must be submitted with this form): ______________________________________
Upgrade
Demo
Calibration
Health and safety
Evaluation
Return for Credit
Substances (please refer to MSDS forms)
The product has been exposed to the following substances:
(by selecting ‘YES’ you MUST complete the table to the right)
* Agilent will not accept delivery of any product that is exposed to radioactive, biological,
explosive substances or dioxins, PCB’s without written evidence of decontamination.
Trade name
Toxic
YES
NO
Harmful
YES
NO
Corrosive
YES
NO
Reactive
YES
NO
Flammable
YES
NO
Explosive (*)
YES
NO
Radioactive (*)
YES
NO
Biological (*)
YES
NO
Oxidizing
YES
NO
Sensitizer
YES
NO
Other dangerous substances
YES
NO
Chemical name
Chemical Symbol
CAS Number
Goods preparation
If you have replied YES to one of the above questions. Has the product been purged?
If yes, which cleaning agent/method:
YES
NO
Has the product been drained from oil?
I confirm to place this declaration on the outside of the shipping box.
YES
NOT APPLICABLE
I declare that the above information is true and complete to the best of my knowledge and belief.
I understand and agree to the terms and conditions on page 2 of this document.
Name:
Authorized Signature:
Position:
Date:
NOTE: If a product is received at Agilent which is contaminated with a toxic or hazardous material that was not disclosed, the customer will be held
responsible for all costs incurred to ensure the safe handling of the product, and is liable for any harm or injury to Agilent employees as well as to any third
party occurring as a result of exposure to toxic or hazardous materials present in the product.
Page of
Agilent VPD Request for Return
Agilent Vacuum Products Division/Sales and Service Offices
Request for Return Form
United States
Agilent Technologies
121 Hartwell Avenue
Lexington, MA 02421 - USA
Tel.: +1 781 861 7200
Fax: +1 781 860 5437
Toll-Free: +1 800 882 7426
[email protected]
Benelux
Agilent Technologies Netherlands B.V.
Groenelaan 5, 1186 AA Amstelveen
The Netherlands
Tel: +31 20 547 2000
Fax: +31 20 547 2093
Brazil
Agilent Technologies Brasil
Avenida Marcos Penteado de Ulhoa
Rodrigues, 939 - 6° andar
Castelo Branco Office Park
Torre Jacarandá - Tamboré
Barueri, Sao Paulo CEP: 06460-040
Toll free: 0800 728 1405
China
Agilent Technologies (China) Co. Ltd
No.3, Wang Jing Bei Lu, Chao Yang District
Beijing, 100102, China
Tel: +86 (0)10 64397888
Fax: +86 (0)10 64391318
Toll free: 800 820 3278
[email protected]
[email protected]
France
Agilent Technologies
Parc Technopolis - Z.A. de Courtaboeuf
3, avenue du Canada - CS 90263
91978 Les Ulis cedex, France
Tel: +33 (0) 1 64 53 61 15
Fax: +33 (0) 1 64 53 50 01
[email protected]
Germany and Austria
Agilent Technologies
Sales & Services GmbH & Co. KG
Lyoner Str. 20
60 528 Frankfurt am Main
GERMANY
Tel: +49 69 6773 43 2230
Fax: +49 69 6773 43 2250
India
Agilent Technologies India Pvt. Ltd.
Unit Nos 105-116
First Floor, Splendor Forum,
Plot No.-3 , District Centre, Jasola
New Delhi-110025
Ph: +91 11 4623 7100
Fax: +91 4623 7105
Toll Free: 18001801517
Italy
Agilent Technologies Italia S.p.A.
Via F.lli Varian, 54
10040 Leini, (Torino) - Italy
Tel: +39 011 9979 111
Fax: +39 011 9979 350
Toll free: 00 800 234 234 00
[email protected]
Southeast Asia
Agilent Technologies Sales Sdn Bhd
Unit 201, Level 2 uptown 2,
2 Jalan SS21/37, Damansara Uptown
47400 Petaling Jaya,
Selangor, Malaysia
Tel : +603 7712 6106
Fax: +603 6733 8121
Toll free: 1 800 880 805
[email protected]
Japan
Agilent Technologies Japan, Ltd.
8th Floor Sumitomo Shibaura Building
4-16-36 Shibaura Minato-ku
Tokyo 108-0023 - Japan
Tel.: +81 3 5232 1253
Fax: +81 3 5232 1710
Toll-Free: 0120 655 040
[email protected]
Korea
Agilent Technologies Korea, Ltd.
Shinsa 2nd Bldg. 2F, 966-5 Daechi-dong
Kangnam-gu, Seoul
Korea 135-280
Tel: +82 (0)2 2194 9449
Fax: +82 (0)2 3452 3947
Toll free: 080 222 2452
[email protected]
Mexico
Agilent Technologies
Concepcion Beistegui No 109
Col Del Valle
C.P. 03100 – Mexico, D.F.
Tel.: +52 5 523 9465
Fax: +52 5 523 9472
UK and Ireland
Agilent Technologies UK, Ltd.
6 Mead Road Oxford Industrial Park
Yarnton, Oxford OX5 1QU – UK
Tel.: +44 (0) 1865 291570
Fax: +44 (0) 1865 291571
Singapore
Agilent Technologies Singapore Pte. Ltd,
1 Yishun Avenue 7,
Singapore 768923
Tel : (65) 6215 8045
Fax : (65) 6754 0574
Toll free: 1 800 2762622
[email protected]
Taiwan
Agilent Technologies Taiwan Limited
20 Kao-Shuang Road Ping-Chen City
Tao-Yuan Hsien,
32450 Taiwan, R.O.C.
Tel: +886 3 4959004
Toll free: 0800 018 768
[email protected]
Other Countries
Agilent Technologies Italia S.p.A.
Via F.lli Varian, 54
10040 Leini, (Torino) - Italy
Tel.: +39 011 997 9111
Fax: +39 011 997 9350
Toll-Free: 00 800 234 234 00
Customer Support & Service
NORTH AMERICA:
Toll Free: 800 882 7426
[email protected]
EUROPE:
Toll Free: 00 800 234 234 00
[email protected]
PACIFIC RIM:
please visit our website for individual office
information
http://www.agilent.com/chem/vacuum
Worldwide Web Site, Catalog and Order
On-line:
www.agilent.com/chem/vacuum
Representatives in most countries
12/13
© Agilent Technologies, Inc. 201
Printed in ITALY
11/2014
Publication Number: 87-901-037-01 (A)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement