iDS-3301S_UserManual_EN_V1.0 20100225.pub

iDS-3301S_UserManual_EN_V1.0 20100225.pub
IP NETWORK
1CH VIDEO SERVER
User’s Manual
iDS-3301S
VERSION 1.0
ENGLISH
BEFORE GET STARTED
Safety Warning
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
Do not insert any metallic object through ventilation grills.
Caution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK:
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
General Notice
Product specifications are subject to change without prior notice.
2
TABLE OF CONTENT
Table of Content
I.
Package Content
4
II.
Panel View & Function
5
III.
Specification
6
IV.
Installation
8
A.
Display
8
B.
Hardware
9
C.
IP Manager
10
D.
ActiveX Control
14
IP Viewer
15
A.
Login ID & Password
15
B.
Graphic User Interface
16
C.
On-Screen Operations
17
D.
Pan/Tilt/Zoom Control
18
System Configuration
19
A.
System
20
B.
Network
23
C.
Audio & Video
28
D.
Event
32
E.
Search
36
Factory Default
38
V.
VI.
VII.
Appendix I
Network Environment
Appendix II Recommended SD Cards
39
42
3
I. PACKAGE CONTENT
I. Package Content
Following items can be found in each original product package:
●
IP Server Main Unit
●
Power Adaptor
●
Network Cross-Over Cable
●
Wireless Receiver (selected models only)
●
Quick Guide
●
Software CD
NB. SD Card disc is not included.
4
II. PANEL VIEW & FUNCTION
II. Panel View & Function
FRONT VIEW
Alarm Input
SD Card Port
Inserting two sensor
input devices
Inserting SD Card
(not included)
Relay Out
Connecting to two alarm
output devices
REAR VIEW
Ethernet Port
Video In / Out
Connecting to network
Connecting to video
input and output
Wireless Port
PTZ Control
Selected models only
RS-485 for PTZ or
other integrations
RS-232 Port
System integrations
DC Power In
Audio In / Out
Connecting with power
Connecting to
microphone output
and speaker input
5
III. SPECIFICATION
III. Specification
VIDEO
Video Standard
H.264 & JPEG, dual streaming support
Group of Picture (GOP)
I / IP, selectable 3 levels multiplier
Data Rate
Streaming 1: 32 kbps ~ 4 Mbps CBR, 1 ~ 10 levels VBR
Streaming 2: 32 kbps ~ 3 Mbps CBR, 1 ~ 10 levels VBR
Video Quality
5 lv (best, high, standard, low, lowest)
Resolution & Frame Rate
NTSC / PAL
D1
720x480 / 720x576 30/25 fps
4CIF
704x480 / 704x576 30/25 fps
CIF
352x240 / 352x288 30/25 fps
QCIF
176x120 / 176x144 30/25 fps
Video In
Composite: 1 x BNC
Video In Loop Through
Composite: 1 x BNC
Full Screen
Yes
Imaging Contour
Brightness, contrast, hue, saturation
Zooming
Digital 4X
AUDIO
Compression Format
ADPCM, bi-directional audio streaming
Audio Line Input / Output
1 / 1 RCA jack
CPU MODULE
CPU
ARM 9, 32-bit RISC
DDR2/ ROM
128MB / 8MB
ALARM
Alarm In / Out / Relay
2 x In, 2 x Relay (N.O. interval selectable), terminal block
Video Analytics
Video Motion Detection (VMD), 3 zones, 10 sensitivity lv
Triggering Reaction
Relay out, E-Mail, FTP, SD archiving
Pre / Post Event
5 / 10 sec recording
PTZ Control
RS-485, terminal block
Integration
RS-232, D-sub 9-pin
NETWORK
Protocols
3GPP, DDNS, DHCP, FTP, HTTP, NTP, PPPoE, RTSP, SMTP, TCP/IP, UDP,
UPnP
Ethernet
10/100 Base-T, auto sensing, RJ-45
Wireless
IEEE 802.11b/g compliant (embedded, optional)
PoE
IEEE 802.3af compliant (embedded)
User Group
3 levels, maximum 20 users, 10 users simultaneously
Encryption
WEP 64 / 128-bit, WPA, PSK
6
IV. FEATURE & SPECIFICATION
LOCAL RECORDING
SD Card Storage *
VMD, Network IP check, network disconnection recording (wired model only)
Format
AVI (H.264/ JPEG), JPEG
Control
Playback, File management
REMOTE RECORDING
Mobile Surveillance
3G (M-PEG4)/ 3G Symbian / iPhone/ Blackberry
Web Surveillance
Web browser, manual, VMD, AVI, snapshot, playback
Professional Surveillance
iNVR Basic 36 surveillance system (iNVR Pro 36 optional)
GENERAL
Unit Configuration
Via web browser (reboot, factory default, date/time synchronization, OSD overlay)
Profile Management
Configuration values export & import
Firmware
HTTP mode, remote update
Authentication
ID, Password
Log Listing
System, VMD, Alarm
Certification
CE, FCC
MECHANICAL
Dimension (HxWxD)
134.0 x 42.0 x 107.0 mm
Weight
400 g
ELECTRICAL
Input Voltage
DC 12V, front LED indicator
Power Consumption
Wired: 350mA, 4.2W; Wireless: 450mA, 4.5W
BROWSING REQUIREMENT
OS
Microsoft Windows 2000 / XP / 2003 / Vista / Windows7
CPU
Intel Celeron 1.66 GHz, 1024 MB RAM
Graphic
128 MB
Web Browser
Microsoft Internet Explorer 6.0 or above
ENVIRONMENTAL
Operating
0˚C ~ 45˚C
Storage
-30˚C ~ 60˚C
Humidity
0 ~ 80% RH non-condensing
7
IV. INSTALLATION
IV. Installation
This chapter contains following four main sections:
A.
Display
B.
Hardware
C.
IP Manager
D.
ActiveX Control
A. Display
a.
On desktop, right-click mouse, then select [Properties].
b.
Go to [Settings], on [Color Quality], change color quality of display to 32 bit.
8
IV. INSTALLATION
B. Hardware
a.
Connect IP Server directly to PC or network with Ethernet cable provided.
b.
Connect third-party alarm input and relay output devices to I/O terminal blocks located on front
panel. Connect third-party PTZ to RS-485 port located on rear panel. Connect RS-232-based, thirdparty devices to RS-232 port located on rear panel for system integrations. Function of each RS-232
pin is described in the followings:
For locations of I/O, RS-485, and RS-232 ports, please refer to diagram drawn in <Panel View &
Function>.
c.
Provide electricity to IP Server with power adaptor provided.
9
IV. INSTALLATION
C.
IP Manager
IP Manager is a smart and convenient application aimed at assisting individual users for assigning IP
addresses for IP Server in just a few mouse clicks. It is available in Software CD provided in the
package.
IP Manager can configure three types of IP instantly:
●
●
●
Fixed IP (public IP or virtual IP)
DHCP (dynamic IP)
Dial-up (PPPoE)
a.
Double-click IP Manager icon in order to execute.
b.
Unblock Windows Firewall alert if you are using Windows XP SP2 or above.
c.
IP Manager Graphic User Interface.
IP Manager will search all IP Servers connected to
the current network. Or users can click [SEARCH]
to refresh the network again.
Default IP is 192.168.1.210.
10
IV. INSTALLATION
d.
Modify IP parameters.
Click one of the IP Servers listed on the left menu. The network parameters of this particular IP Server
will be shown on the right menu. Users may change Name of IP Sever with personal attachment (e.g.,
office, warehouse, etc).
After changing all required parameters, click [SUBMIT] to apply the changes.
Finally click [OK] in order to re-boot the device.
e.
Subnet.
It is extremely important that both PC and IP Server must locate within the SAME SUBNET. An
example is provided in the followings:
If both have the SAME subnet:
IP SEVER:
192.168.1.210
PC:
192.168.1.100
If both DO NOT have the same subnet:
IP SERVER:
192.168.2.210
PC:
192.168.1.100
If your PC and IP Server DO NOT locate within the same
subnet, please follow steps described below accordingly:
1. Locate Windows OS setting window for TCP/IP:
[Control Panel] > [Network Connections] >
[Local Area Connection] > [Properties] >
[Internet Protocol (TCP/IP)]
Double-click on [Internet Protocol (TCP/IP)] or click on
[Properties] in order to change settings.
11
IV. INSTALLATION
2.
Modify Subnet Mask values.
Make sure both IP Server and PC have identical values.
f.
Launch IP Server.
The easiest way to access IP Server remotely is by double-clicking on a selected IP Server listed on [IP
Network Device List] on IP Manager. After that, IP Server will be launched in a standard Internet
browser such as Microsoft Internet Explorer.
Or alternatively, you may open an Internet browser and enter IP address of IP Server in the [Address Bar]
directly.
12
IV. INSTALLATION
Finally you will be prompt for following dialogue window, asking you to confirm security changes made
to Internet browser. Click [Yes] to continue.
13
IV. INSTALLATION
D.
ActiveX Control
a.
Accept ActiveX Control to be installed.
For first access of IP Server in this particular PC, Internet browser will request you the permission to install an ActiveX Control provided by IP Server.
b.
Security Level of Internet Browser.
If installation has been failed, please verify Security Setting of Internet browser. Following is an example
for Microsoft Internet Explorer:
Internet Explorer > [Tools] > [Internet Options] > [Security] > [Custom Level…] > [Security Settings].
Locate the following options and select [Enable] or [Prompt] for both of them:
●
●
Download unsigned ActiveX control
Initialize and script ActiveX controls not marked as safe
See examples shown on the following page:
14
V. IP VIEWER
V. IP Viewer
IP Viewer is a web-based surveillance platform designed for remote surveillance purposes such as realtime display, playback, and management. It has already been embedded inside of each IP Server, user is
not required to install any additional software in order to operate it.
This chapter contains four sections and will describe initialization and basic operations of IP Viewer:
A.
Login ID & Password
B.
Graphic User Interface
C.
On-Screen Operations
D.
Pan/Tilt/Zoom Control
A.
Login ID and Password
After successful configurations of IP parameters and installation of ActiveX Control, launch IP Server in
an Internet browser again, user will be bringing into IP Viewer for user-identity authentication.
To log-in, enter factory-default User Name and Password carefully:
Default User Name is
Default Password is
admin
admin
Note that, both User Name and Password are case sensitive.
Remember my password. For extra security, Do NOT click especially if you are using a public PC.
15
V. IP VIEWER
B.
Graphic User Interface
Now you shall see IP Viewer main graphic user interface (GUI) as shown below. Primary functions of IP
Viewer is to display real-time video streaming and provide complete system configurations of IP Server
remotely.
2
3
4
5
6
1
7
8
9
10
11
1
Real-time display
2
Snapshot an evidence
3
Recording
4
Digital zoom
5
Playback SD archives
6
System configuration
7
Status bar
8
Pan/Tilt/Zoom control
9
Dual streaming channel
10
Bi-directional audio communication
11
Online visitor
12
Alarm relay output 1 & 2
12
1.
Real-Time Display panel shows live streaming of video information remotely.
2.
Snapshot an Evidence of important event in still JPEG format.
3.
Recording as AVI files continuously. For details, see next section.
4.
Digital Zoom for bringing up an area of interest closely. For details, see next section.
5.
Playback SD Archives of important events captured and stored in local SD Card medium.
6.
System Configuration for user accounts, system, network, video, audio, events, etc.
7.
Status Bar shows system time, video resolution, and current video frame rate.
8.
Pan/Tilt/Zoom Control enables maneuvering of such functions. See P/T/Z Control section.
9.
Dual Streaming Channel enables secondary viewing device (such as mobile or PDA
phones) to receive real-time streaming at lower-yet-appropriate frame rate per second. This
feature is available only if Streaming 2 is being enabled in Video setting.
10. Bi-directional Audio Communication enables full-duplex voice communication between
local and remote surveillance sites. To speak, click on [Communication] box. To listen, enable Incoming Audio in Audio setting.
11. Online Visitor shows number of users are currently accessing this IP Server.
12. Alarm Relay Output enables manual activation of alarm relay-out devices.
16
V. IP VIEWER
C.
On-Screen Operations
There are five more features available on the main GUI.
Right-click mouse on the real-time video, then a pop-up menu will show up as follows:
Snapshot.. This is identical to Snapshot an Evidence
Record Start. This is identical to Recording button
function described above.
shown on the main GUI. Continuous manual
recording (round-the-clock, RTC) of both audio (if enabled) and video streams in standard AVI format
in the PC. You will be prompt for the location where is used to save file in the PC.
To avoid single AVI file being oversized that cannot be opened by PC, IP Server will save continues
recording in next, new AVI file every 15 minutes automatically.
To stop recording, right-click mouse again, then select [Record Stop].
You may playback recorded AVI files via a standard Microsoft Media Player on any third-party PC
without having required to install third-party video codec in advance.
Mute.. Turn off the audio. Click again to turn it on.
Full Screen. Simply double-click on the real-time video, it will be enlarged into full-screen mode. Press
[Esc] on keyboard or double-click the real-time video again, it will be returned back to normal mode.
Or select [Full Screen] on the pop-up menu in order to operate.
Zoom. IP Server provides 4X digital zooming. This is identical to Digital Zoom
on the main GUI.
button shown
Click on [Enable digital zoom] in order to activate this function. Drag on [Percentage Bar] in order to
select appropriate zooming size (1~4X). Drag the [Green Block] in order to zoom-up a particular area of
interest on real-time display.
17
V. IP VIEWER
D.
Pan/Tilt/Zoom Control
Real-time Pan/Tilt/Zoom control interface is available on the main GUI of IP Viewer.
First, on [Model], select a third-party PTZ protocol best describe your third-party PTZ connected via
RS-485 port. Available functions will vary by brands and models defined by their respective
manufacturers. Then, setup [Camera ID] and [Baud Rate] for connection.
To operate, click on applicable control icons for your third-party PTZ shown on the interface:
1.
Navigation Cursor for manual control of PTZ directions. To operate, select one of the
directions. To return to factory default position, click on home
button.
2.
Auto Pan allows automatic movement of PTZ horizontally.
3.
Auto Patrol allows automatic guarding of preset patrol points in a sequence.
4.
Optical Zoom allows zooming in or out of zoom lens module.
5.
Focus Control allows better focus of targeting object.
6.
Auto Focus allows automatic adjustment of lens focus.
7.
Auto Iris allows automatic adjustment of lens iris.
8.
PT Speed allows adjustment of panning and tilting speed. Default: 5. Range: 0 ~ 5.
9.
Patrol Point provides two functions: (1) allows PTZ to move to one of the preset
locations in just one-click of button, and (2) established a sequence for PTZ to patrol
automatically (please refer to Auto Patrol above). To setup, please refer to followings:
01. Select a Preset Point. Range: 1 ~ 9 (Point 0 is not applicable).
02. In Name block, enter a meaningful name (e.g., main entrance) for the point.
03. Click on
button.
in order to apply the name for the point. To delete, click on
04. All preset points will be listed in the menu. To operate, select a point to move to.
18
VI. SYSTEM CONFIGURATION
VI. System Configuration
This chapter will provide detailed surveillance settings for IP Viewer.
On IP Viewer, click [System Configuration] button as shown below in order to enter:
After successful entering, a setting page will be shown on Internet browser:
Once you have finished settings, click [Live] icon shown below in order to return to real-time display of
IP Server:
There chapter contains five main sections and will detail complete system configurations thoroughly:
A.
System
B.
Network
C.
Audio & Video
D.
Event
E.
Search
19
VI. SYSTEM CONFIGURATION
A.
System
This section contains three main portions as follow:
a.
System Information
b.
User Management
c.
System Update
a.
System Information.
1.
Server Information.
You may set up camera name, language, and date/time in this section.
Server Name. This is the name of IP Server and will also displays on IP Manager.
Ethernet MAC. This is MAC address for Ethernet module and is NOT for wireless module (optional).
Select language. You may change language of setup menu in this
section. After selection, following dialogue window will pop up,
and click [OK] to confirm the change.
2.
On-Screen Display (OSD) Setting.
Click on [Enabled] in order to display date/time
on real-time display screen. Location of OSD is
customisable.
3.
Date & Time.
You may set up date format, time zone, methods of date/time adjustment in this section.
To adjust date/time, user may either synchronize with NTP Server or PC, or may enter
manually.
Finally, click on [Apply] to effect the changes.
20
VI. SYSTEM CONFIGURATION
b.
User Management.
You may setup user authority and manage multiple account information in this section:
IP Server supports four levels of user authority: administrator, guest, PTZ guest, and anonymous user.
1.
Anonymous User Login.
Select [Yes] to allow anonymous login. Select [No] to request User Name and Password when accessing
IP Server. Anonymous User is not allowed to enter System Configuration pages.
2.
Add User.
Enter new set of User Name and Password, then click [Add/Set].
If guest account’s User Name entered is already existing, click [Add/Set], the new Password entered will
override. This method, however, does not apply to administrator account.
Guest/PTZ Guest User is also not allowed to enter System Configuration pages.
IP Server accepts maximum 20 registered user accounts and 10 simultaneous user login.
3.
User List.
All registered user accounts will be listed in this section. You may click [Edit] or [Remove] to modify
each account. If you click [Edit], following dialogue window will pop up. You will be allowed to
modify User Name and Password again.
For extra security, you are recommended to
change your password every 30 days.
21
VI. SYSTEM CONFIGURATION
c.
System Update.
1.
Firmware Upgrade.
To update firmware remotely, click [Browse…], and select the location of firmware file from PC. Then
click [Upgrade] to proceed. Follow online instructions to continue.
2.
Reboot System.
Click [Start] to re-boot IP Server.
3.
Return to Factory Default Settings.
Click [Start] to delete and return all settings of this IP Server back to factory default values.
4.
Profile Management.
Profile Management allows export and import of configurations values of IP Server. For one, you may
backup current settings for future use. For another, you will save a lot of time configuring more than one
IP Server of identical or similar settings.
Export. Right-click on [Download] in order to [Save As] a file in PC.
Import. Click on [Browse…] in order to overwrite configuration file saved in the past or from another IP
Server. Click [Upgrade] then follow the rest of online instructions to continue.
22
VI. SYSTEM CONFIGURATION
B.
Network
This section contains five main portions as follow:
a.
Internet Protocol
b.
PPPoE
c.
DDNS
d.
Mail & FTP
e.
Wireless (optional)
a.
Internet Protocol.
1.
Address.
IP Server supports both DHCP and Static connection modes.
DHCP.. By using DHCP, IP Server will receive all the network parameters automatically.
Static IP. Enter IP information in corresponding blocks manually.
2.
Port.
Enter port information under this section if it is so required. Default port for IP Server is 80.
RTSP/RTP ports are designated for 3GPP mobile surveillance. RTP may start from 1024 and end from
1025, and both may not exceed 10000. Consult this section with your local telecom service provider.
3.
UPnP Service.
Click [Enabled] if your router supports network UPnP (universal plug and play). IP Server will be shown
up in Windows My Network Place automatically without using IP Manager to detect and launch.
Finally, click [Apply] to effect the changes.
23
VI. SYSTEM CONFIGURATION
b.
PPPoE.
1.
Setup.
IP Server supports PPPoE method of Internet connection via ADSL modem.
Click [Enabled] in order to activate. Enter ADSL dial-up User Name and Password in corresponding
blocks.
2.
E-Mail Alert.
This is a system security alert feature. When Internet connection via PPPoE method is being established,
IP Server will send an e-mail notification to a user-specified e-mail account.
Click on [Enabled] in order to activate. You may also modify e-mail title in [Subject] line.
For settings over e-mail, please refer to Mail & FTP settings.
Finally, click [Apply] to effect the changes.
c.
DDNS.
For IP Server installed behind ICS or NAT devices, DDNS (Dynamic DNS) service is required.
1.
Setup.
Click on [Enabled] in order to activate DDNS support.
Provider. Select a service provider then enter required account information in corresponding blocks.
24
VI. SYSTEM CONFIGURATION
Scheduled Update. Most free DDNS service providers (e.g., DynDNS.org) have restriction for
frequency of use per period of time. You shall not make schedule timing too frequent, otherwise Host
Name may be blocked. Recommended refreshing interval is every 1,440 minutes (i.e., once a day).
2.
Status.
This section will display status of DDNS connection. Below are typical system messages:
Updating. Service information is being updating.
Idle. Currently not in service.
DDNS registration successful, can now log by http://<username>.ddns.camddns.com.. Register
successfully. You may proceed login.
Update Failed, the name is already registered. The user name has already been used. Please change
it. You shall provide different User Name.
Update Failed, please check your internet connection. Network connection failed. Check your network
connection again.
Update Failed, please check the account information you provide. The server, user name, and
password may be wrong. Check your server and account information again.
Finally, click [Apply] to effect the changes.
d.
Mail & FTP.
This section allows users to set up e-mail account and FTP server [PORT/PASV] in order to receive
alert messages and graphic evidences from IP Server.
Finally, click [Apply] to effect the changes.
25
VI. SYSTEM CONFIGURATION
e.
Wireless.
Please note, wireless network feature is available only to selected models, and is based on IEEE 802.11
b/g protocols.
Following steps will guide you through setup procedures for wireless connection:
1.
Connect IP Server directly to PC with cross-over network cable provided in the package.
2.
Use IP Manager to detect IP Server. Modify IP information that is identical with parameters set in
wireless Router. Finally click [Submit] to apply changes and reboot IP Server.
3.
Use IP Manager to detect IP Server and then launch IP Viewer in standard Internet browser.
4.
Enter [System Configuration] then click [Wireless], and following setup window will be shown:
5.
Available Wireless Networks.
IP Server will display all wireless Routers it detected in this table. Make sure your wireless Router is
detected and listed.
6.
Setup.
Please make sure all data are identical between IP Server and wireless Router.
Wireless MAC. This is MAC address for wireless module and is NOT for Ethernet module.
Mode. Infrastructure Mode is for connecting with Router and Ad-Hoc Mode is for connecting with PC.
Operation Mode.. Selections for IEEE 802.11 b or g. If you are not sure, please select Auto.
SSID. This refers to network ID of IP Server. It can be the name of IP Server or can be different, as long
as it is identical with SSID registered in wireless Router.
Channel. This setting is available only under Ad-Hoc mode. Channel refers to channel number on
wireless device, and it must be identical among IP Server, PC, and wireless Router.
26
VI. SYSTEM CONFIGURATION
Security. IP Server provides industry’s most advanced encryption protection over wireless transmission.
Supported methods include: WEP and WPA-PSK.
Once again, encryption setting over IP Server has to be identical with wireless Router’s.
WEP Setting.
Authentication.. Either Open System or Shared Keys. Please refer to your wireless
Router. If you are not sure, select Auto.
Encryption.. Either 64-bit or 128-bit. Please refer to your wireless Router.
Key Type. Key may be regarded as set of passwords to access wireless connection. Either HEX
or ASCII. By selecting HEX type, you may only use numbers from 0 to 9 and letters from A to
F, and minimum length is 10 for 64-bit and 26 for 128-bit. By selecting ASCII type, you may
input any case-sensitive characters and minimum length is 5 for 64-bit and 13 for 128-bit.
Key 1~4.. Based on Key Type, enter keys in these blocks.
WPA-PSK Setting.
Encryption. Either TKIP or AES. Please refer to your wireless Router.
Pre-Shared Key. Enter ASCII-format key in this block. All numbers and characters are
allowed and are case sensitive.
Finally, click [Apply] to effect the changes. Close IP Viewer. Detach cross-over network cable between
IP Server and PC.
Now you may use IP Manager to detect wireless network and then to launch IP Server in IP Viewer wirelessly. Or you may enter IP address in Internet browser in order to launch IP Viewer directly and wirelessly.
27
VI. SYSTEM CONFIGURATION
C.
Audio & Video
This section contains three main portions as follow:
a.
Image
b.
Video
c.
Audio
a.
Image.
This section allows you to fine tune image reproduction quality digitally.
Real-Time Preview Window
Preview. Real-Time Preview Window shown above helps you to preview the changes.
Contour. You may fine tune Brightness, Contrast, Hue, and Saturation levels. Click [Default] if you
would like to discard changes made this time and return to factory default values.
Advanced Parameters.
1.
Back Light Compensation (BLC)
2.
Night Mode refers to downsize of maximum video frames to be transmitted during night time. Be
cause noise signals usually are very high at night or under dark, thus video size will become larger
and larger, and will therefore take too much unnecessary bandwidth and HDD space. By selecting
Night mode function, you can intelligently constrain maximum frames of video to be recorded per
second at night time.
3.
Video Orientation. Either flip (180 degree) or mirror (mirroring).
Click [Default] if you would like to discard changes made this time or return to factory default
values.
28
VI. SYSTEM CONFIGURATION
b.
Video.
This section allows you to specify how video streaming may be compressed and transmitted over
network. This IP Server supports dual streaming, allowing secondary viewing device to receive real-time
IP steaming at substantially low frame rates per second, while at the same time, does not affect settings of
primary viewing channel.
Streaming 1
Streaming 2
1.
Primary Viewer which usually will consume large bandwidth level (e.g., main
monitoring station like IP Viewer and iNVR surveillance system software)
Secondary Viewer which usually cannot enjoy large bandwidth level (e.g., mobile
device like 3GPP, 3G Symbian, and Smartphone mobile and PDA phones)
Streaming 1&2. There are two modes available for settings: Basic and Advanced modes.
Basic Mode.
Resolution. This refers to resolution of video and there are four sizes to choose from:
NTSC / PAL
D1
720 x 480 / 720 x 576
4CIF
704 x 480 / 704 x 576
CIF
352 x 240 / 352 x 288
QCIF
176 x 120 / 176 x 144
Quality.. This refers to quality of video streaming, and there are five levels to choose from. The higher the
quality is, the bigger the files size will be.
Video Frame Rate. This refers to maximum frames can be transmitted per second (fps). Maximum rate is
at 30fps for NTSC and 25fps for PAL. In general, the higher the rate is, the better the video quality will be.
As well, when video quality is higher, compression size is bigger and will take more bandwidth, thus
maximum rate can be received in remote site will be less.
Video Format. IP Server supports dual codices: H.264 and JPEG format. Choose one of them that is best
for your network bandwidth and storage capacity.
Video System. Either 60 Hz (mainly NTSC) or 50 Hz (mainly PAL). This will affect maximum Video
Frame Rate may be transmitted.
RTSP Path. When using Smartphone device (3G Symbian, Windows Embedded, or Windows Mobile)
for mobile surveillance, enter RTSP address here. Examples:
29
VI. SYSTEM CONFIGURATION
rtsp://xxx.xxx.xxx.xxx/
rtsp://xxx.xxx.xxx.xxx/v2
Streaming 1 without incoming audio
Streaming 2 without incoming audio
Please consult RTSP address with your telecom service provider.
Advanced Mode. Additional fine setting options include the followings:
Bitrate Control Mode. Either CBR (Constant Bit
Rate) or VBR (Variable Bit Rate). For both of them,
the higher the rate is, the better the video quality will
be. Please test carefully for each bit rate level.
GOP Size. It refers to Group of Pictures per transmission unit. The higher the GOP is, the better the
video quality will be.
3GPP Mode.
3GPP Mode is designed for mobile surveillance using 3GPP protocol. Due to limitation of protocol itself,
maximum video resolution is at QCIF. If you would like to transmit larger resolution of video, please use
Smartphone device (3G Symbian, Windows Embedded, or Windows Mobile) with RTSP setting in
Advanced Mode (both Streaming 1 and Streaming 2). Examples:
rtsp://xxx.xxx.xxx.xxx/3g
rtsp://xxx.xxx.xxx.xxx/3gx
with incoming audio stream
without incoming audio stream
Please note, not all countries and telecom companies support 3GPP features necessary for private content
streaming. Please consult this with your local telecom service provider prior to operation.
Finally, click [Apply] to effect the changes.
Please note, since total video frame rate of this IP Server is 30/25fps by hardware, total frame rates of
Streaming 1 and Streaming 2 together CANNOT exceed 30/25fps.
Please note, primary viewing channel may be set as Streaming 2. That is, there is no restriction to say that
Streaming 2 shall always be the low-bandwidth channel. But if you are using 3GPP connection for remote
surveillance, it will always connect to Streaming 2. If you are using Smartphone device via RTSP ports
for remote surveillance, either streaming channel is acceptable.
30
VI. SYSTEM CONFIGURATION
c.
Audio.
This IP Server provides one audio input port (to microphone) and one audio output port (to speaker), as
well it supports bi-directional audio streaming, thus allowing direct and simultaneous voice
communication between local and remote users.
To enable audio transmission from IP Server (local) to IP Viewer (remote), click [Enabled] to activate.
To enable audio transmission from IP Viewer (remote) to IP Server (local), click [Communication] on IP
Viewer real-time display window.
Please note, by enabling audio communication, it means portions of CPU resource and network
bandwidth will be consumed by audio, thus maximum video (frames per second) may be transmitted may
have to be decreased technically.
31
VI. SYSTEM CONFIGURATION
D.
Event
This section contain three main portions as follow:
a.
Video Motion Detection
b.
Event Triggering
c.
Alarm I/O
a.
Video Motion Detection.
1.
Setup.
Video motion detection (VMD) is a video content
analytics (VCA) which can detect motion occurred in
video digitally. When VMD is being detected, a
series of reactions may be taken automatically.
Area. Each IP Server is eligible for three areas of
VMD. Each one is represented in different color. To
activate, click [Area 1] button then use mouse to drag
an area on preview window.
Sensitivity. This function enables sensitive level of
VMD. For instance, the size of a person is very small
on a public square and the size is even smaller if
camera is mounted far away. Thus, the movement of
this person usually cannot be sensed sharply. If you
encounter similar situations, you can increase sensitivity level of VMD. The higher the sensitivity level is,
the more sensitive the detection result will be.
Area 1/2/3. Check box of [Area 1] in order to setup method of reactions (described below) when a motion
is being detected. The same method also applies to [Area 2] and [Area 3].
E-Mail. When a motion is being detected, an Alert Message with video evidence as attachment will be
sent to a pre-defined e-mail account.
FTP. When a motion is being detected, video evidence will be sent to a pre-defined FTP account.
Save to SD Card. When a motion is being detected, evidence will be recorded to local SD Card storage
port (video only). At the same time, you may also Send a Text Log to e-mail or FTP, notifying users that
there has been an event occurred locally.
32
VI. SYSTEM CONFIGURATION
Subject. Title of Alert Message to be sent via e-mail.
Interval. This is referring to period between two VMD events. Thus IP Server will not overreact to a
longer-time event. Interval between two motions detected recordings is fixed at 10~60 second.
b.
Event Triggering
This section defines types and lengths of
evidence to be sent to pre-defined e-mail
account and FPT server.
As well, when network is disconnected, events
may be recorded to local SD Card storage.
1.
Recording Format.
AVI File. IP Server will send one clip of video evidence in AVI format or JPEG, with respect to prealarm and post-alarm recording made in Recording Length section.
Series of JPEG File(s). IP Server will send a series of still image evidence in JPEG format, with respect
to pre-alarm and post-alarm recording made in Recording Length section. This feature is available only
when Video Compression is set to JPEG mode.
Single JPEG File. IP Server will send one piece still image evidence in JPEG format, with respect to
frequency made in Interval section.
Because the size of still JPEG is the smallest, this option is recommended for e-mail alerts or those who
use mobile device (mobile and PDA phones) to receive e-mails.
2.
Recording Length.
IP Server is intelligent enough to process pre-alarm and post-alarm recording so that you will never miss
any important events against your interests.
Pre Alarm:
Post Alarm:
0~5 second.
0~10 second.
33
VI. SYSTEM CONFIGURATION
3.
Network Disconnection Recording.
Important events shall always be recorded when network is not available (not able to send alert
messages with video or image evidences via e-mail or FTP). Click [Record to SD Card] to enforce
compulsory recording of events to local SD card storage, even if [Save to SD Card] is not enabled in
Video Motion Detection section. After network is re-established, users may access to SD Card in order
to playback events occurred during disconnected period.
AVI files at 5fps will be saved to SD Card continuously.
Please note, this feature is only available to non-wireless models.
4.
Network IP Detection.
Click [Enabled] to activate IP Check function, then enter a website to be connected for testing.
Action of each IP Check may be stored on SD Card for future reference. Interval between two
recordings on SD Card is fixed at 30 second.
Finally, click [Apply] to effect the changes.
Please note, settings over this section will apply to methods of reactions in Alarm I/O section.
34
VI. SYSTEM CONFIGURATION
c.
Alarm I/O.
IP Server supports 2 x Alarm Input and 2 x Alarm Output. You may specify methods of output when
input is being triggered.
1.
Input Setup.
Input 1 & 2 Sensor. Select either Normally-Open (NO) or Normally-Closed (NC) for input sensors.
Input 1 & 2 Reaction. When input sensor is being triggered, select what reactions to be undertaking: Email, FTP, Output No. 1 & No. 2, and Save to SD Card.
Recording Format & Recording Length. Please conduct these settings in Event Triggering section.
Save to SD Card. When a motion is being detected, evidence will be recorded to local SD Card storage
port (video only). At the same time, you may also Send a Text Log to e-mail or FTP, notifying users that
there has been an event occurred locally.
Subject.
Title of Alert Message to be sent via e-mail.
Interval.
The period between two triggered events. Thus IP Server will not over-react to a
longer-time event. Range: 10 ~ 60 seconds.
2.
Output Setup.
Mode.
On/Off Switch. Events will either turn on or off alarms repeatedly.
Time Switch. Event monitoring will be terminated after a pre-defined time interval.
Interval Range: 1 ~ 60 seconds.
35
VI. SYSTEM CONFIGURATION
d.
Schedule.
IP Camera supports schedule recording for events. You may specify the schedule by hour or day.
1.
Schedule Setup.
By hour. Click the grid in table to enable the time that you want to record. Which green grid indicates
enabled record, white grid indicates disabled record. Also you may click the number 0 ~ 23 to
set the schedule for each day.
By day. Click Mon. ~ Sun. to set full time record for each day.
Full time record.
2.
Click “All” to enable/disable full time record.
Snapshot
Within the schedule, IP camera provides an additional function—Snapshot. It will capture a JPEG image
and send to the E-mail, FTP server or Save to SD card to inform the user.
Interval. The period between two snapshots. Range: 1 ~ 50000 seconds.
36
VI. SYSTEM CONFIGURATION
E.
Search
This section contains two main portions as follow:
a.
Playback
b.
Log Book
a.
Playback.
IP Server feature one SD Card storage port (card is not included in the package) for local recording. In
case any events occur, you may access IP Server then search and playback SD archives for verifications.
To use, please insert a SD Card into the port completely.
When there is no SD Card inserted, playback window will be shown as follow:
When there is a SD Card inserted and recording has proceeded, playback window will shown as follow:
Date
Storage Space
Date. Recorded events are categorized by date. Click a [Date] in order to search.
Storage Space. This section shows Used and Free Size of inserted SD Card storage medium.
1.
To playback, click on one of the dates, a list of events similar to the following will be shown:
Event types include: video motion detection, alarm
triggering (selected models only), network
disconnection (non-wireless models only) , and
network IP detection.
There are 10 events per page, and there can be as many
pages as SD Card space is available.
37
VI. SYSTEM CONFIGURATION
AVI files are saved in AVI format, and maybe playback by standard Windows Media Player without
having special video codec pre-installed.
Please note, when undertaking local recording of AVI video clips to SD Card, audio is not included. In
order to playback full video with audio simultaneously, please use free-bundle 36-channel advanced
remote surveillance system NVR software provided in Software CD.
2.
File Management. Check blank boxes then click [Del] in order to delete selected files from SD
Card.
SD Card will overwrite itself automatically when available space is full. Please choose a size of SD Card
that can at least record certain period of time. For instance, there is a network failure during a weekend
and no technician is available, thus no remote recording of events to advanced NVR surveillance system
is possible. In this case, you will need a SD Card for at least two days of local recording against
network failure. For extra security, make sure you will always verify SD archives per period of time or
whenever receive event notifications via e-mails.
b.
Log Book.
This section allows you to review all important events occurred to this IP Server. Types of log include:
System, Video Motion Detection, and Alarm I/O.
38
VII. FACTORY DEFAULT
VII. Factory Default
In case User Name, Password, and/or IP information are lost, users may reset all values back to factory
default. Please follow steps described below:
Factory Default
Pressing the button
A.
Unplug the power.
B.
Press the button shown above.
C.
Plug-in the power. Do not release the button during this process.
D.
Hardware re-booting will take in approximately 30 seconds.
E.
Release the button.
F.
Use IP Manager in order to customise user-specified IP environment again:
Default IP Address
192.168.1.210
Default User Name
admin
Default Password
admin
39
APPENDIX I
Appendix I
Network Environment
Following section will demonstrate three typical examples of general network planning and setting for a
typical home/office environment.
A.
One Fixed/Dynamic IP
@
IP Server
+
CCTV Camera
Situation:
Broadband
Modem
Internet
Remote PC
Only IP Server is being connected to the Internet.
Only 1 x Fixed/Dynamic IP is available in the network.
Device:
1 x ADSL/Cable Modem needed.
Connection: a. If you are using Fixed IP, enter it directly to IP Server (IP Manager).
b. If you are using Dynamic IP, use PPPoE to dial up.
40
APPENDIX I
Appendix I
B.
Two or More Fixed/Dynamic IP
Local PC
@
Switch
Hub
Broadband
Modem
Internet
Remote PC
IP Server
+
CCTV Camera
Situation:
Both IP Server and Local PC are being connected to the Internet.
There are 2 (or more) x Fixed/Dynamic IP are available in the network.
Device:
1 x ADSL/Cable Modem is needed.
1 x Network Hub is needed.
Connection: a. If you are using Fixed IP, enter it directly to IP Server (IP Manager).
b. If you are using Dynamic IP, use PPPoE to dial up.
41
APPENDIX I
Appendix I
C.
Virtual IP
Local PC
@
IP Sharing
Broadband
Modem
Internet
Remote PC
IP Server
+
CCTV Camera
Situation:
Both IP Server and Local PC are being connected to the Internet.
Only 1 x Fixed/Dynamic IP.
Device:
1 x ADSL/Cable Modem is needed.
1 x IP Sharing device is needed.
Connection: Set up port forwarding in IP Sharing device.
42
APPENDIX II
Appendix II
Recommended SD Cards List
Users are recommended to use following SD Card brands and models:
SanDisk 128MB
Transcend 128MB
SanDisk 256MB
Transcend 256MB
SanDisk 512MB
Transcend 512MB
SanDisk 1GB
Transcend 1GB
SanDisk 2GB
Transcend 2GB
SanDisk 4GB
Transcend 4GB
SanDisk 8GB
Transcend 8GB
SanDisk16GB
Transcend 16GB
Please note, specifications of third-party items may change from time to time without prior notice, and IP
Server holds no responsibility whatsoever for any incompatibility this may incur. Please contact an
authorised professional near you for most up-to-date information.
43
RoHS
Copyright © 2010 iProSecu Corporation. All rights reserved. Specifications are subject to change without prior notice.
V1.0 EN 0210 Printed in Taiwan
44
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement