User Manual PCM-4153
User Manual
PCM-4153
PC/104+ SBC w/AMD LX800,
VGA, LCD, LAN, USB2.0 and
Flash
Copyright
The documentation and the software included with this product are copyrighted 2012
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
VIA is a trademark of VIA Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation.
Intel, Pentium, Celeron, and MMX are registered trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
All other product names or trademarks are properties of their respective owners.
On-line Technical Support
For more information on this and other Advantech products, please visit our websites
at: http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our support website at:
http://www.advantech.com/support
PCM-4153 User Manual
Part No. 2006415312
Edition 3
Printed in China
May 2012
ii
Declaration of Conformity
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Packing List
Before you begin installing your card, please make sure that the following materials
have been shipped:
 1 x PCM-4153 SBC
 1 x AT Power cable (p/n:1700003491)
 1 x Audio cable (p/n:1700000918)
 1 x Four COM cable (p/n:1701400181)
 1 X RS-422/485 COM cable (p/n:1703040157)
 1 x Keyboard/Mouse cable (p/n:1703060053)
 1 x Y cable (for KB/MS extension) (p/n:1700060202)
 2 x Ethernet RJ-45 Conn. conversion cable (p/n:1701105158)
 1 x LPT port cable (p/n:1700260250)
 1 x IDE cable (p/n:1701440350)
 1 x VGA cable (p/n:1700000898)
 2 x USB cable (bracket type with two USB ports) (p/n: 1703100121)
 1 x Startup manual
 1 x CD-ROM (Manual, Driver, Utility)
If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Model No. List
Description
PCM-4153F-L0A2E
PC/104+ SBC w/AMD LX800, VGA, LVDS, LAN, USB, On board
memory and Flash
PCM-4153FZ-L0A2E
PCM-4153F-L0A2E with Phoenix Gold package
PCM-4153FZ2-L0A2E
PCM-4153F-L0A2E with Phoenix Platinum package
iii
PCM-4153 User Manual
Technical Support and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manufacturer.Discard used batteries according to the manufacture’.s instructions.
PCM-4153 User Manual
iv
Contents
Chapter
1
General Information ............................1
1.1
1.2
1.3
Introduction ............................................................................................... 2
Features .................................................................................................... 2
Specifications ............................................................................................ 2
1.3.1 Standard PC/104 Biscuit SBC Functions...................................... 2
1.3.2 VGA/LVDS Interface ..................................................................... 3
1.3.3 Ethernet Interface ......................................................................... 3
1.3.4 Audio Function .............................................................................. 3
1.3.5 OS support.................................................................................... 3
1.3.6 Mechanical and Environmental..................................................... 3
Board Layout: Dimensions ........................................................................ 4
Figure 1.1 Board layout: dimensions (component side) .............. 4
Figure 1.2 Board layout: dimensions (solder side) ...................... 4
1.4
Chapter
2
Installation............................................5
2.1
Jumpers .................................................................................................... 6
Table 2.1: Jumper/Switch Setting:............................................... 6
Connectors................................................................................................ 7
Table 2.2: Connectors ................................................................. 7
Locating Connectors ................................................................................. 8
Figure 2.1 Connectors (component side) .................................... 8
Figure 2.2 Connectors (solder side) ............................................ 8
Setting Jumpers ........................................................................................ 9
IDE, CDROM Hard Drive Connector (CN11) ............................................ 9
2.5.1 Connecting the Hard Drive............................................................ 9
Flash ....................................................................................................... 10
Parallel Port Connector (CN19) .............................................................. 10
Keyboard and PS/2 Mouse Connector (CN18) ....................................... 10
Power Connectors (CN38) ...................................................................... 10
2.9.1 Main Power Connector, +5 V, +12 V (CN38).............................. 10
2.9.2 Power Reset Button .................................................................... 10
Audio Interfaces (CN34/35)..................................................................... 10
2.10.1 Audio Connector Audio-out(CN35), Audio-in(CN34) .................. 10
Table 2.3: Serial Port RS-422/485 (CN39) ................................ 11
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
Chapter
3
Award BIOS Setup .............................13
3.1
Introduction ............................................................................................. 14
3.1.1 CMOS RAM Auto-backup and Restore ...................................... 14
Entering Setup ........................................................................................ 14
Figure 3.1 Award BIOS Setup initial screen .............................. 14
Standard CMOS Setup ........................................................................... 15
Standard CMOS Setup ........................................................................... 15
Advanced BIOS Features ....................................................................... 15
Figure 3.2: Advanced BIOS features screen .............................. 15
3.5.1 Virus Warning ............................................................................. 16
3.5.2 First/Second/Third/Other Boot Device ........................................ 16
3.5.3 Boot Up NumLock Status............................................................ 16
3.5.4 Gate A20 Option ......................................................................... 16
3.5.5 Typematic Rate Setting............................................................... 16
3.5.6 Typematic Rate (Chars/Sec)....................................................... 16
3.5.7 Typematic Delay (msec) ............................................................. 16
3.2
3.3
3.4
3.5
v
PCM-4153 User Manual
3.10
3.11
3.12
3.5.8 Security Option ........................................................................... 16
Integrated Peripherals............................................................................. 17
3.6.1 IDE Master/Slave PIO/UDMA Mode, .......................................... 17
3.6.2 Integrated peripherals screen ..................................................... 17
3.6.3 Onboard LAN Control ................................................................. 17
3.6.4 IDE HDD Block Mode ................................................................. 17
3.6.5 Onboard Serial Port .................................................................... 17
3.6.6 Onboard Parallel Port ................................................................. 17
3.6.7 Parallel Port Mode ...................................................................... 17
3.6.8 EPP Mode Select........................................................................ 18
3.6.9 ECP Mode Use DMA .................................................................. 18
Power Management Setup ..................................................................... 18
Figure 3.3: Power management setup screen............................ 18
3.7.1 ACPI function.............................................................................. 18
3.7.2 Power Management.................................................................... 18
3.7.3 Video Off In Suspend.................................................................. 19
3.7.4 Modem Use IRQ ......................................................................... 19
3.7.5 HDD Power Down....................................................................... 19
3.7.6 PowerOn By Modem................................................................... 19
3.7.7 PowerOn By Alarm ..................................................................... 19
3.7.8 Primary IDE 0 (1) and Secondary IDE 0 (1) ............................... 19
3.7.9 FDD, COM, LPT PORT .............................................................. 19
3.7.10 PCI PIRQ [A-D]#......................................................................... 19
PnP/PCI Configurations .......................................................................... 20
3.8.1 PnP OS Installed ........................................................................ 20
Figure 3.4: PnP/PCI configurations screen ................................ 20
3.8.2 Reset Configuration Data ........................................................... 20
3.8.3 Resources Controlled by: ........................................................... 20
3.8.4 PCI/VGA Palette Snoop.............................................................. 20
PC Health Status .................................................................................... 21
3.9.1 PC Health Status Screen............................................................ 21
Password Setting .................................................................................... 21
Save & Exit Setup ................................................................................... 22
Exit Without Saving................................................................................. 22
4
PCI SVGA/LCD Setup ....................... 23
4.1
4.4
Introduction ............................................................................................. 24
4.1.1 Display Type .............................................................................. 24
4.1.2 Dual Simultaneous Display........................................................ 24
4.1.3 CMOS Setting for Panel Type ................................................... 24
Connections to Two Standard LCDs....................................................... 24
4.2.1 AMD Geode LX........................................................................... 24
Table 4.1: Connections to Sharp LQ121S1DG31 / PCM-4153 . 24
Installation of the SVGA Driver ............................................................... 25
4.3.1 Installation Chipset AES Driver................................................... 26
4.3.2 Installation of VGA Driver ........................................................... 28
4.3.3 PCI Bridge .................................................................................. 31
Further Information ................................................................................. 32
5
Audio Setup....................................... 33
5.1
5.2
Introduction ............................................................................................. 34
Driver Installation .................................................................................... 34
5.2.1 Before You Begin........................................................................ 34
5.2.2 Windows XP Drivers ................................................................... 35
3.6
3.7
3.8
3.9
Chapter
4.2
4.3
Chapter
PCM-4153 User Manual
vi
Chapter
6
Ethernet Interface ..............................39
6.1
6.2
6.3
Introduction ............................................................................................. 40
Installation of Ethernet driver .................................................................. 40
6.2.1 Installation for Windows XP ........................................................ 40
Further information.................................................................................. 44
Appendix A
Pin Assignments ...............................45
A.1
Jumper and Connector Tables................................................................ 46
Table A.1: J2, DOTREF Select .................................................. 46
Table A.2: J3, Clear CMOS ....................................................... 46
Table A.3: CN39, COM2 Setting................................................ 46
Table A.4: J4-Flash select ......................................................... 47
Table A.5: J5, PCI VI/O POWER ............................................... 47
Table A.6: CN38, Power Input ................................................... 47
Table A.7: CN4, TFT LCD I/F .................................................... 48
Table A.8: CN5, Inverter Power ................................................. 49
Table A.9: CN6, SMBus............................................................. 49
Table A.10:CN32, Reset / Buzzer pin header............................. 49
Table A.12:CN36, GPIO1 ........................................................... 50
Table A.13:CN37, GPIO2 ........................................................... 50
Table A.14:CN11, IDE ................................................................ 50
Table A.11:CN33-Battery Connector .......................................... 50
Table A.15:CN27, CRT ............................................................... 52
Table A.16:CN15, USB1/2 .......................................................... 52
Table A.17:CN17, USB3/4 .......................................................... 53
Table A.18:CN30, COM1/2/3/4 ................................................... 53
Table A.19:CN19, Print Port ....................................................... 54
Table A.20:CN20, RS422/485 .................................................... 55
Table A.21:CN35, AUDIO-OUT .................................................. 55
Table A.22:CN34, AUDIO-IN ...................................................... 56
Table A.23:CN23, ISA -5V & -12V Input ..................................... 56
Table A.24:CN25, LAN1 ............................................................. 56
Table A.25:CN26, LAN2 ............................................................. 57
Table A.26:CN18, KB/MS ........................................................... 57
Appendix B
System Assignments ........................59
B.1
System I/O Ports ..................................................................................... 60
Table B.1: System I/O Ports ...................................................... 60
1st MB Memory Map ............................................................................... 61
Table B.2: 1st MB Memory Map ................................................ 61
DMA Channel Assignments .................................................................... 61
Table B.3: DMA Channel Assignments...................................... 61
Interrupt Assignments ............................................................................. 62
Table B.4: Interrupt Assignments............................................... 62
B.2
B.3
B.4
Appendix C
Mechanical Drawings ........................63
C.1
Mechanical Drawings .............................................................................. 64
Figure C.1 PCM-4153 Mech drawing (comp side) ..................... 64
Figure C.2 PCM-4153 mech drawing (sol side) ......................... 64
Appendix D
Prog. GPIO & Watchdog Timer.........65
D.1
GPIO Function: Its Call by Int15 Hook. ................................................... 66
vii
PCM-4153 User Manual
PCM-4153 User Manual
viii
Chapter
1
1
General Information
This chapter gives background
information on the PCM-4153.
Sections include:
 Introduction
 Features
 Specifications
 Board Layout: Dimensions
1.1 Introduction
The PCM-4153 is a fanless, best-cost, performance PC/104+ SBC (Single Board
Computer) geared to satisfy the needs for various industrial computing equipment.
PCM-4153 is ideal for communication, gaming and medical applications that require flat
panel support using digital displays with TTL interfaces and two Ethernet ports.
For those who want superior performance for various low-power embedded applications, PCM-4153 uses an AMD LX-800 processor clocked at 500 MHz, in conjunction
with onboard DDR333 system memory.
PCM-4153 offers convenient connector layout, easy assembly, multiple I/O, and
includes two 10/100Mbps Ethernet, four USB (Universal Serial Bus) 2.0 and four
serial ports for easy system expansibility.
1.2 Features







AMD low power LX800 500MHz Processor
Support 1GB on board flash and 512 memory
Supports 24-bit TFT LCD interface
Supports Dual 100Base-T Fast Ethernet
Supports Four USB2.0 ports
Supports Four COM ports
PC/104+ expansion interface
1.3 Specifications
1.3.1 Standard PC/104 Biscuit SBC Functions
















CPU: AMD Geode® LX800 processor, up to 500 MHz
System memory: on board memory DDR333 SDRAM 512 MB
2nd cache memory: 128 KB on the processor
System chipset: AMD Geode LX800
BIOS: AWARD 4Mbit Flash BIOS
Watchdog timer: 255 levels timer interval
Expansion interface: PC/104+
Battery: Lithium 3V/196 mAH
Power management: ACPI supported
Enhanced IDE interface: One channel supports one EIDE device (another is
used for on board IDE Flash). BIOS auto-detect, PIO Mode 3 or Mode 4, supports UDMA 33 mode
Serial ports: Four serial RS-232 ports in one 40 pin connector (CN30: COM1/2/
3/4). RS-422 and RS-485 in one pinheader (CN20) and can be configured via
CN39 connector.
Parallel port: One parallel port, supports SPP/EPP/ECP mode
Keyboard/mouse connector: Supports one standard PC/AT keyboard and a
PS/2 mouse
Audio: Support AC97 Audio stereo sound
USB: Four USB 2.0 ports compliant universal serial bus ports
Flash: Onboard 1 GB Flash (IDE interface, default setting is slave)
PCM-4153 User Manual
2





Chipset: AMD Geode LX800
Memory size: Optimized Shared Memory Architecture, support 64MB frame
buffer using system memory
Resolution: CRT resolution: up to 1600 x 1200 x 16 bpp at 100 Hz and up to
1024 x 768 x 32 bpp at 60 Hz for TFT LCD
LCD interface: Supports up to 24-bit TFT LCD (TTL signal)
Dual simultaneous display: CRT + LCD



Chipset supports: 2 x 10/100Mbps - Intel 82551ER
Interface: 2 x internal box header
Standard IEEE 802.3u (100 BASE-T) protocol compatible
1.3.4 Audio Function


Audio controller: Realtek ACL203 chipset, supports AC97 3D Audio stereo
sound
Audio interface: Microphone in, Line in, Line out
1.3.5 OS support


This board supports Win XP, Win CE and Win XPe.
For further information about OS support in your PCM-4153, visit the following
web resource Advantech: website: www.advantech.com or please contact technical support center
1.3.6 Mechanical and Environmental









Dimensions: 96 x 115 mm (3.77"x 4.05")
Mechanical Drawing (dxf file) is available.
Power supply type: AT
Power Requirement: +5 V ± 5%, +12 V ± 5% (Optional), (5V only, 12V optional
for PC104 add on card and LCD inverter)
Power consumption:
– (Geode LX800, 512 MB DDR333)
– Power on - boot: +5 V @ 1.548A, +12 V @ 0.01A
– Max load: +5 V @ 1.46 A, +12 V @ 0.02 A
– Idle mode: +5 V @ 1.37 A, +12 V @ 0.01A
Conditions:
– Test software: Hot CPU pro 4.22
– Power on - boot: Measure the maximum current value of between system
power on and boot-up to O.S.
– Max load: Measure the maximum current value which system under maximum load (CPU: Top speed, RAM & Graphic: Full loading)
– Idle mode: Measure the current value when system in windows mode and
without running any program
Operating temperature: 0 ~ 60°C (32 ~ 140°F) (operation humidity: 40°C @
85% RH Non-Condensing)
Extended temperature support:
– -20°C - 80°C: PCM-4153FZ-L0A2E
– -40°C - 85°C: PCM-4153FZ2-L0A2E
Weight: 0.85 kg (reference weight of total package)
3
PCM-4153 User Manual
General Information
1.3.3 Ethernet Interface
Chapter 1
1.3.2 VGA/LVDS Interface
1.4 Board Layout: Dimensions
0.00
90.17
Figure 1.1 Board layout: dimensions (component side)
95.89
87.63
87.63
62.91
23.63
14.49
8.26
8.26
90.17
102.87
2.02
0.00
12.70
4.45
97.69
0.00
Figure 1.2 Board layout: dimensions (solder side)
PCM-4153 User Manual
4
Chapter
2
2
Installation
This chapter explains the setup
procedures of the PCM-4153 hardware, including instructions on
setting jumpers and connecting
peripherals, switches and indicators. Be sure to read all safety precautions before you begin the
installation procedure.
2.1 Jumpers
The PCM-4153 has a number of jumpers that allow you to configure your system to
suit your application. The table below lists the functions of the various jumpers.
Table 2.1: Jumper/Switch Setting:
J2
DOTREF Select
J3
Clear CMOS
J4
Flash Master/Slave select
J5
PCI VI/O Power Selector
CN39
COM2 Setting
J2
DOTREF Select
Setting
Function
(1-2)
External
NL
Internal
J3
Clear CMOS
Setting
Function
(1-2)
BAT (default)
NL
Clear-CMOS
CN39
COM2 Setting
Setting
Function
(1-2)
RS232 (default)
(3-4)
RS485
(5-6)
RS422
J4
Flash Master/Slave select
Setting
Function
(1-2)
Slave (default)
(2-3)
Master
PCM-4153 User Manual
6
PCI VI/O POWER
Setting
Function
(1-2)
With +5V
(2-3)
With +3.3V (Default)
Chapter 2
J5
Onboard connectors link the PCM-4153 to external devices such as hard disk drives,
a keyboard, or floppy drives. The table below lists the function of each of the board’s
connectors.
Table 2.2: Connectors
CN1
ATX feature power connector (optional)
CN4
TFT LCD I/F
CN5
Inverter Power
CN6
SMBus
CN11
IDE
CN15
USB1/2 / CN17 USB 3/4
CN18
KB/MS
CN19
Print Port
CN20
RS422/485
CN23
ISA -5V & -12V Input
CN25
LAN1 / CN26 LAN2
CN27
CRT
CN30
COM1/2/3/4
CN32
Reset / Buzzer pin header
CN33
Battery connector
CN35
AUDIO-OUT / CN34 AUDIO-IN
CN36
GPIO1 / CN37 GPIO2
CN38
Power Input
7
PCM-4153 User Manual
Installation
2.2 Connectors
2.3 Locating Connectors
Figure 2.1 Connectors (component side)
CN35
CN27
Figure 2.2 Connectors (solder side)
PCM-4153 User Manual
8
You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two
metal pins and a small metal clip (often protected by a plastic cover) that slides over
the pins to connect them. To “close” a jumper, you connect the pins with the clip. To
“open” a jumper, you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2 and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
closed
closed 2-3
The jumper settings are schematically depicted in this manual as follows:.
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes. Generally, you
simply need a standard cable to make most connections.
2.5 IDE, CDROM Hard Drive Connector (CN11)
The board provides 1 IDE channel which you can attach up to two Enhanced Integrated Drive Electronics hard disk drives or CDROM to the board’s internal controller.
Its IDE controller uses a PCI interface. This advanced IDE controller supports faster
data transfer, PIO mode 3, mode 4 and up to UDMA33/66.
2.5.1 Connecting the Hard Drive
Connecting drives is done in a daisy-chain fashion. This package includes One
44PIN IDE cable that can connect to 1.8" and 2.5" drives.
1. Connect one end of the cable to Hard Drive connector. Make sure that the red
(or blue) wire corresponds to pin 1 on the connector, which is labeled on the
board (on the right side).
2. Plug the other end of the cable into the Enhanced IDE hard drive, with pin 1 on
the cable corresponding to pin 1 on the hard drive. (See your hard drive’s documentation for the location of the connector.)
If desired, connect a second drive as described above.
Unlike floppy drives, IDE hard drives can connect to either end of the cable. If you
install two drives, you will need to set one as the master and one as the slave by
using jumpers on the drives. If you install only one drive, set it as the master.
9
PCM-4153 User Manual
Installation
open
Chapter 2
2.4 Setting Jumpers
2.6 Flash
The board provides onboard NAND Flash memory to replace the CF socket. PCM4153 supports 1 GB flash. Flash endurance is about 100K program/erase cycles and
data retention is 10 years.
The Flash memory provides excellent performance at low cost, is vibration resistant
and has extremely low power consumption.
The on-board flash controller supports IDE interface and PIO Mode 4.
2.7 Parallel Port Connector (CN19)
Normally, the parallel port is used to connect the cable to a printer. The board
includes a multi-mode (ECP/EPP) parallel port accessed via CN19 and a 26-pin flatcable connector. You will need an adapter cable if you use a traditional DB-25 connector. The adapter cable has a 26-pin connector on one end, and a DB-25 connector on the other.
The parallel port is designated as LPT1, and can be disabled or changed to LPT2 or
LPT3 in the system BIOS setup.
The parallel port interrupt channel is designated to be IRQ7.
You can select ECP/EPP/ECP DMA channel via BIOS setup.
2.8 Keyboard and PS/2 Mouse Connector (CN18)
The board provides a keyboard connector that supports both a keyboard and a PS/2
style mouse. In most cases, especially in embedded applications, a keyboard is not
used. If the keyboard is not present, the standard PC/AT BIOS will report an error or
fail during power-on self-test (POST) after a reset. The PCM 4153’s BIOS standard
setup menu allows you to select “All, But Keyboard” under the “Halt On” selection.
This allows no-keyboard operation in embedded system applications, without the
system halting under POST.
2.9 Power Connectors (CN38)
2.9.1 Main Power Connector, +5 V, +12 V (CN38)
Supplies main power +5V to the PCM-4153, and to devices that require +12 V.
2.9.2 Power Reset Button
Momentarily pressing the reset button will activate a reset. The switch should be
rated for 10 mA, 5 V.
2.10 Audio Interfaces (CN34/35)
2.10.1 Audio Connector Audio-out(CN35), Audio-in(CN34)
The board provides all major audio signals on a 8-pin cable connector, These audio
signals include Microphone in (mono), Line in (stereo) and Line out (stereo).
PCM-4153 User Manual
10
The board provides four serial ports: Four serial RS-232 ports in one Hirose 40 pin
connector(CN30: COM1/2/3/4). It provides connections for serial devices or a communication network. You can find the pin assignments for the COM port connector in
Appendix C.
2.11.1 Serial Port RS-422/485 (CN20)
Table 2.3: Serial Port RS-422/485 (CN39)
Setting
Function
1-2
RS-232 (default)
3-4
RS-485
5-6
RS-422
2.12 VGA/LCD Interface Connections
The board’s PCI SVGA interface can drive conventional CRT displays and is capable
of driving a wide range of flat panel displays.
2.12.1 CRT Display Connector (CN27)
The CRT display connector is a 15-pin D-SUB connector used for conventional CRT
displays.
2.12.2 TTL TFT LCD Connector (CN4)
For PCM-4153 series, CN4 consists of a 40-pin connector which can support up to
24-bit LCD panel. It is Hirose’s product no. DF13A-40DP-1.25 V
2.13 Ethernet Configuration
The board is equipped with two high performance 32-bit PCI-bus Ethernet interface
which are fully compliant with IEEE 802.3U 10/100Mbps standards. They are supported by all major network operating systems.
2.13.1 100Base-T Connector (CN25, CN26)
100Base-T connections are made via two internal 10-pin box header.
2.14 Watchdog Timer Configuration
An onboard watchdog timer reduces the chance of disruptions which EMP (electromagnetic pulse) interference can cause. This is an invaluable protective device for
standalone or unmanned applications. Setup involves one jumper and running the
control software (refer to Appendix A).
11
PCM-4153 User Manual
Installation
Serial ports can be configured to operate in RS-422 and RS-485 mode. RS-422 and
RS-485 in one pinheader (CN20) and can be configured via CN39 connector.
Chapter 2
2.11 COM Port Connector (CN20,CN30)
2.15 USB Connectors (CN15,CN17)
The board provides up to four USB (Universal Serial Bus) ports using Plug and Play.
The USB interfaces comply with High Speed USB specification Rev. 2.0 which supports 480Mbps transfer rate, and are fuse protected.
The USB interface is accessed through two 5 x 2-pin flat-cable connectors. You will
need an adapter cable if you use a standard USB connector. The adapter cable has a
5 x 2-pin connector on one end and a USB connector on the other.
The USB interfaces can be disabled in the system BIOS setup.
2.16 GPIO (General Purpose Input Output) (CN36/
CN37)
The board supports 8-bit GPIO through GPIO connector. The 8 digital inputs and outputs can be programmed to read or control devices, with each input or output
defined. The default setting is 8 bits input.
PCM-4153 User Manual
12
Chapter
3
3
Award BIOS Setup
3.1 Introduction
Award’s BIOS ROM has a built-in setup program that allows users to modify the
basic system configuration. This type of information is stored in battery-backed memory (CMOS RAM) so that it retains the setup information when the power is turned
off.
3.1.1 CMOS RAM Auto-backup and Restore
The CMOS RAM is powered by an onboard button cell battery. When you finish BIOS
setup, the data in CMOS RAM will be automatically backed up to Flash ROM. If operation in harsh industrial environments causes a software error, the BIOS will recheck
the data in CMOS RAM and automatically restore the original data in Flash ROM to
CMOS RAM for booting.
Note!
If you intend to change the CMOS setting without restoring the previous
backup, you have to click on "DEL" within two seconds of the "CMOS
checksum error..." display screen message appearing. Then enter the
"Setup" screen to modify the data. If the "CMOS checksum error..."message appears again and again, please check to see if you need to
replace the battery in your system.
3.2 Entering Setup
Turn on the computer and check for the “patch code”. If there is a number assigned to
the patch code, it means that the BIOS supports your CPU.
If there is no number assigned to the patch code, please contact Advantech’s applications engineer to obtain an up-to-date patch code file. This will ensure that your
CPU’s system status is valid. After ensuring that you have a number assigned to the
patch code, press <Del> to allow you to enter the setup.
Figure 3.1 Award BIOS Setup initial screen
PCM-4153 User Manual
14
Choose the “Standard CMOS Features” option from the “Initial Setup Screen” menu,
and the screen below will be displayed. This menu allows users to configure system
components such as date, time, hard disk drive, Video, Halt On, display, and memory.
3.4 Standard CMOS Setup
Chapter 3
3.3 Standard CMOS Setup
Award BIOS Setup
3.5 Advanced BIOS Features
The “Advanced BIOS Features” screen appears when choosing the “Advanced BIOS
Features” item from the “Initial Setup Screen” menu. It allows the user to configure
the board according to his particular requirements. Below are some major items that
are provided in the Advanced BIOS Features screen.
Figure 3.2: Advanced BIOS features screen
15
PCM-4153 User Manual
3.5.1 Virus Warning
If enabled, a warning message and alarm beep activates if someone attempts to
write here. The commands are “Enabled” or “Disabled.”
3.5.2 First/Second/Third/Other Boot Device
The BIOS tries to load the OS with the devices in the sequence selected.
Choices are: HDD, CDROM, LAN, Disabled.
3.5.3 Boot Up NumLock Status
This feature selects the “power on” state for NumLock. The commands are
“Enabled” or “Disabled.”
3.5.4 Gate A20 Option
Normal:
A pin in keyboard controller controls GateA20
Fast (Default):
Chipset controls GateA20.
3.5.5 Typematic Rate Setting
The typematic rate is the rate key strokes repeat as determined by the keyboard controller. The commands are “Enabled” or “Disabled.” Enabling allows the typematic
rate and delay to be selected.
3.5.6 Typematic Rate (Chars/Sec)
BIOS accepts the following input values (characters/second) for typematic rate: 6, 8,
10, 12, 15, 20, 24, 30.
3.5.7 Typematic Delay (msec)
Typematic delay is the time interval between the appearance of two consecutive
characters, when holding down a key. The input values for this category are: 250,
500, 750, 1000 (msec).
3.5.8 Security Option
This setting determines whether the system will boot up if the password is denied.
Access to Setup is always limited.
System The system will not boot, and access to Setup will be denied if the correct
password is not entered at the prompt.
Setup
Note!
The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt.
To disable security, select “PASSWORD SETTING” in the main menu.
At this point, you will be asked to enter a password. Simply press
<Enter> to disable security. When security is disabled, the system will
boot, and you can enter Setup freely.
PCM-4153 User Manual
16
3.6.1 IDE Master/Slave PIO/UDMA Mode,
IDE Master/Slave PIO/UDMA Mode (Auto) has a master and a slave, making two
IDE devices possible. Because each IDE device may have a different Mode timing
(0, 1, 2, 3, 4), it is necessary for these to be independent. The default setting “Auto”
will allow auto detection to ensure optimal performance.
Award BIOS Setup
3.6.2 Integrated peripherals screen
3.6.3 Onboard LAN Control
Options are Enable or Disable. Select Disable if user does not want to use onboard
LAN controller1
3.6.4 IDE HDD Block Mode
You can enable the Primary IDE channel and/or the Secondary IDE channel. Any
channel not enabled is disabled. This field is for systems with only SCSI drives.
3.6.5 Onboard Serial Port
For settings reference the Appendix for the serial resource allocation,
and Disabled for the on-board serial connector
3.6.6 Onboard Parallel Port
This field sets the address of the onboard parallel port connector. You can select
either 3BCH/IRQ7, 378H/IRQ7, 278H/IRQ5 or Disabled. If you install an I/O card with
a parallel port, make sure there is no conflict in the address assignments. The CPU
card can support up to three parallel ports, as long as there are no conflicts for each
port.
3.6.7 Parallel Port Mode
This field allows you to set the operation mode of the parallel port. The setting “Normal” allows normal speed operation, but in one direction only. “EPP” allows bidirectional parallel port operation at maximum speed. “ECP” allows the parallel port to
operate in bi-directional mode and at a speed faster than the maximum data transfer
rate. “ECP + EPP” allows normal speed operation in a two-way mode.
17
Chapter 3
3.6 Integrated Peripherals
PCM-4153 User Manual
3.6.8 EPP Mode Select
This field allows you to select EPP port type 1.7 or 1.9.
3.6.9 ECP Mode Use DMA
This selection is available only if you select “ECP” or “ECP + EPP” in the Parallel Port
Mode field. In ECP Mode Use DMA, you can select DMA channel 1, DMA channel 3,
or Disable. Leave this field on the default setting.
3.7 Power Management Setup
The power management setup controls the CPU card’s “green” features to save
power. The following screen shows the manufacturer’s defaults:
Figure 3.3: Power management setup screen
3.7.1 ACPI function
The choice: Enabled, Disabled.
3.7.2 Power Management
This category allows you to select the type (or degree) of power saving and is directly
related to the following modes:
1. HDD Power Down
2. Suspend Mode
There are four selections for Power Management, three of which have fixed mode
settings.
Min. Power Saving
Minimum power management., Suspend Mode = 1 hr., and HDD
Power Down = 15 min.
Max. Power Saving
Maximum power management., Suspend Mode = 1 min., and HDD
Power Down = 1 min.
User Defined (Default)
Allows you to set each mode individually. When not disabled, each
of the ranges are from 1 min. to 1 hr. except for HDD Power Down
which ranges from 1 min. to 15 min. and disable.
PCM-4153 User Manual
18
When system is in suspend, video will turn off.
3.7.4 Modem Use IRQ
This determines the IRQ in which the MODEM can use.The choices: 3, 4, 5, 7, 9, 10,
11, NA.
Chapter 3
3.7.3 Video Off In Suspend
3.7.5 HDD Power Down
3.7.6 PowerOn By Modem
When Enabled, an input signal on the serial Ring Indicator (RI) line (in other words,
an incoming call on the modem) awakens the system from a soft off state. The
choices: Enabled, Disabled.
3.7.7 PowerOn By Alarm
When Enabled, your can set the date and time at which the RTC (real-time clock)
alarm awakens the system from Suspend mode. The choices: Enabled, Disabled.
3.7.8 Primary IDE 0 (1) and Secondary IDE 0 (1)
When Enabled, the system will resume from suspend mode if Primary IDE 0 (1) or
Secondary IDE 0 (1) is active. The choice: Enabled, Disabled.
3.7.9 FDD, COM, LPT PORT
When Enabled, the system will resume from suspend mode if FDD, COM port, or
LPT port is active. The choice: Enabled, Disabled.
3.7.10 PCI PIRQ [A-D]#
When Enabled, the system will resume from suspend mode if an interrupt occurs.
The choice: Enabled, Disabled.
19
PCM-4153 User Manual
Award BIOS Setup
You can choose to turn the HDD off after one of the time intervals listed, or when the
system is in “suspend” mode. If the HDD is in a power saving mode, any access to it
will wake it up.
3.8 PnP/PCI Configurations
3.8.1 PnP OS Installed
Select Yes if you are using a plug and play capable operating system. Select No if
you need the BIOS to configure non-boot device
Figure 3.4: PnP/PCI configurations screen
3.8.2 Reset Configuration Data
Default is Disable. Select Enable to reset Extended System Configuration Data
(ESCD) if you have installed a new add-on and system configuration has caused
such a conflict that OS cannot boot.
3.8.3 Resources Controlled by:
The commands here are “Auto” or “Manual.” Choosing “manual” requires you to
choose resources from each following sub-menu. “Auto” automatically configures all
of the boot and Plug and Play devices but you must be using Windows 95 or above.
3.8.4 PCI/VGA Palette Snoop
This is left at “Disabled.”
PCM-4153 User Manual
20
Chapter 3
3.9 PC Health Status
This is to check the PC health, ex: current CPU temperature.
3.9.1 PC Health Status Screen
Award BIOS Setup
3.10 Password Setting
To change the password:
1.
Choose the “Set Password” option from the “Initial Setup Screen” menu and
press <Enter>.
The screen will display the following message
Please Enter Your Password
Press <Enter>.
2.
If the CMOS is good or if this option has been used to change the default password, the user is asked for the password stored in the CMOS. The screen will
display the following message:
Please Confirm Your Password
Enter the current password and press <Enter>.
3.
After pressing <Enter> (ROM password) or the current password (user-defined),
you can change the password stored in the CMOS. The password must be no
longer than eight (8) characters.
Remember, to enable the password setting feature, you must first select either
“Setup” or “System” from the “Advanced BIOS Features” menu.
21
PCM-4153 User Manual
3.11 Save & Exit Setup
If you select this and press <Enter>, the values entered in the setup utilities will be
recorded in the CMOS memory of the chipset. The microprocessor will check this
every time you turn your system on and compare this to what it finds as it checks the
system. This record is required for the system to operate.
3.12 Exit Without Saving
Selecting this option and pressing <Enter> lets you exit the setup program without
recording any new values or changing old ones.
PCM-4153 User Manual
22
Chapter
4
4
PCI SVGA/LCD Setup
This chapter details the software
configuration information. It
shows you how to configure the
card to match your application
requirements. The AWARD System BIOS is covered in Chapter 4.
Sections include:
 Installation of SVGA drivers for
Window XP
 Connections for standard LCDs
 Further information
4.1 Introduction
The board has an onboard AMD Geode LX800 chipset for its PCI/SVGA controller. It
supports TFT LCD displays and conventional analog CRT monitors with 64MB frame
buffer shared with system memory. The VGA controller can drive CRT displays with
resolutions up to 1600 x 1200 x 16 bpp at 100 Hz and up to 1024 x 768 x 32 bpp at
60 Hz for TFT LCD.
4.1.1
Display Type
The board can be set in one of three configurations: on a CRT, on a flat panel display,
or on dual simultaneous display. The system is initially set to dual display mode. If
you want to enable the CRT display only or the flat panel display only, please set
them up from the BIOS screen, or, contact Advantech technical support center.
4.1.2
Dual Simultaneous Display
The board uses a AMD LX800 controller that is capable of providing multiple views
and simultaneous display with mixed video and graphics on a flat panel and CRT.
The Dual display can be set up by CMOS setting.
4.1.3
CMOS Setting for Panel Type
The board system BIOS and custom drivers are located in a 512 KB, Flash ROM
device. A single Flash chip holds the system BIOS, VGA BIOS and network Boot
ROM image. The display can be configured via CMOS settings. This method minimized the number of chips and different type of LCD panels, please choose "panel
type" from the "Advanced Chipset Features" menu in CMOS setting.
4.2 Connections to Two Standard LCDs
Connector Table of 12.1" TTL Sharp LQ121S1DG31 800 x 600 5/3.3V (18 Bit) for
PCM-4153 AMD Geode LX.
4.2.1 AMD Geode LX
Table 4.1: Connections to Sharp LQ121S1DG31 / PCM-4153
Sharp LQ121S1DG31
PCM-4153
DF9MA-41P-1V
DF-13 4OP-1.25V
Pin
Function
Pin
1
GND
3
GND
2
CK
35
DOTCLK
3
GND
4
GND
4
Hsync
38
HS
5
Vsync
36
VS
6
GND
7
GND
8
GND
8
GND
9
R0
27
D18
10
R1
28
D19
PCM-4153 User Manual
24
Function
11
R2
12
GND
D20
13
R3
30
D21
14
R4
31
D22
15
R5
32
D23
16
GND
17
GND
18
GND
19
G0
19
D10
20
G1
20
D11
21
G2
21
D12
22
GND
23
G3
22
D13
24
G4
23
D14
25
G5
24
D15
26
GND
33
GND
27
GND
28
GND
33
GND
29
B0
11
D2
30
B1
12
D3
31
B2
13
D4
32
GND
34
GND
33
B3
14
D5
34
B4
15
D6
35
B5
16
D7
36
GND
34
GND
37
ENAB
37
DE
38
NC
39
VCC
5
+3.3 V
40
VCC
6
+3.3 V
41
NC
PCI SVGA/LCD Setup
29
* The polarity of both synchronous signals are negative.
4.3 Installation of the SVGA Driver
Complete the following steps to install the SVGA driver. Follow the procedures in the
flow chart that apply to the operating system that you are using within your board.
Note!
1.
2.
The windows illustrations in this chapter are intended as examples
only. Please follow the listed steps, and pay attention to the instructions which appear on your screen.
For convenience, the CD-ROM drive is designated as "D" throughout this chapter.
25
Chapter 4
Table 4.1: Connections to Sharp LQ121S1DG31 / PCM-4153
PCM-4153 User Manual
4.3.1 Installation Chipset AES Driver
1.
Open device manager, right click on entertainment then, click on properties
2.
Go to driver page and click on update driver.
3.
Click on install from specific folder and click on next.
PCM-4153 User Manual
26
5.
Click on next.
6.
Click on finish.
PCI SVGA/LCD Setup
Click on browse and select target folder, then, click OK.
Chapter 4
4.
27
PCM-4153 User Manual
4.3.2 Installation of VGA Driver
1.
Right click on video, and click “Properties”.
2.
Go to driver page and click on update driver.
PCM-4153 User Manual
28
4.
Click on browse and select target folder, then click OK.
5.
Click on next, then click on finish.
29
PCI SVGA/LCD Setup
Click on install from specific folder and click on next.
Chapter 4
3.
PCM-4153 User Manual
6.
Then click on continue anyway.
7.
Click on finish.
PCM-4153 User Manual
30
The system may detect PCI bridge automatically. If the question mark is shown on
device manager, please install the driver as below:
1.
Click “Add Hardware Wizard” and add new hardware wizard
Chapter 4
4.3.3 PCI Bridge
PCI SVGA/LCD Setup
31
PCM-4153 User Manual
2.
Search the right directory of PCI bridge for IT8888G driver.
3.
Installation finished.
4.4 Further Information
For further information about the AGP/VGA installation of your PCM-4153, including
driver updates, troubleshooting guides and FAQ lists, visit the following web
resources:
Intel website: www.intel.com
Advantech websites: www.advantech.com
www.advantech.com.tw
PCM-4153 User Manual
32
Chapter
5
5
Audio Setup
The board is equipped with an
audio interface that records and
plays back CD-quality audio. This
chapter provides instructions for
installing the software drivers
included on the audio driver diskettes.
5.1 Introduction
The onboard audio interface provides high-quality stereo sound by using the AMD
LX800 audio controller. The audio interface can record, compress, and play back
voice, sound, and music with built-in mixer control.
5.2 Driver Installation
5.2.1 Before You Begin
Please read the instructions in this chapter carefully before you attempt installation.
The audio drivers for the board are located on the audio driver CD. Run the supplied
SETUP program to install the drivers; don’t copy the files manually.
Note!
The files on the software installation diskette are compressed. Do not
attempt to install the drivers by copying the files manually. You must use
the supplied SETUP program to install the drivers.
PCM-4153 User Manual
34
Open device manager, right click on audio and click on “properties”.
2.
Go to driver page and click on update driver.
3.
Click on install from specific folder and click on next.
35
Audio Setup
1.
Chapter 5
5.2.2 Windows XP Drivers
PCM-4153 User Manual
4.
Click on browse and select target folder, then click OK.
5.
Click on next.
PCM-4153 User Manual
36
7.
Click on finish.
Audio Setup
Click on continue anyway.
Chapter 5
6.
37
PCM-4153 User Manual
PCM-4153 User Manual
38
Chapter
6
6
Ethernet Interface
This chapter provides information on Ethernet configuration.
Sections include:
 Introduction
 Installation of Ethernet drivers
for Windows XP
 Further information
6.1 Introduction
The board is equipped with a high performance 32-bit Ethernet chipset which is fully
compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major
network operating systems. With 100Base-T compatible. The network boot feature
can be utilized by incorporating the boot ROM image files for the appropriate network
operating system. The boot ROM BIOS files are combined with system BIOS, which
can be enabled/disabled in the BIOS setup.
6.2 Installation of Ethernet driver
Before installing the Ethernet driver for Intel 82551ER chipset, note the procedures
below. You must know which operating system you are using with your board, and
then refer to the corresponding installation flow chart, just follow the steps described
in the flow chart.
Note!
The windows illustrations in this chapter are examples only. Follow the
steps and pay attention to the instructions which appear on your screen.
6.2.1 Installation for Windows XP
1.
2.
Select "Start", "Settings". "Control Panel".
Double click "Network".
PCM-4153 User Manual
40
4.
Choose Hardware Device “Ethernet Controller”
Ethernet Interface
Click “Add new hardware wizard” and prepare to install network function
Chapter 6
3.
41
PCM-4153 User Manual
5.
6.
7.
Insert the CD into D: drive
a. Fill in the Find the LAN chipset folder at the directory of PCM-4153 win2000
folder from CD ROM drive
b. Click “OK”.
8.
Choose the "Intel® GD82559ER PCI Adapter" item
PCM-4153 User Manual
42
Click “Next”
Chapter 6
9.
Ethernet Interface
10.
11. Make sure the configurations of relative items are set correctly
12. Click “OK”
43
PCM-4153 User Manual
6.3 Further information
Intel website:
www.intel.com
Advantech websites:
www.advantech.com
www.advantech.com.tw
PCM-4153 User Manual
44
Appendix
A
A
Pin Assignments
This appendix contains information of a detailed or specialized
nature.
A.1 Jumper and Connector Tables
Table A.1: J2, DOTREF Select
Part Number
1653002101
Footprint
JH2X1V-2M
Description
PIN HEADER 2*1P
180D (M) 2.0 mm DIP SQUARE W/O Pb
Setting
Function
(1 - 2)
External
NL
Internal
Table A.2: J3, Clear CMOS
Part Number
1653003101
Footprint
JH3X1V-2M
Description
PIN HEADER 3*1P
180D (M)SQUARE 2.0 mm
Setting
Function
(1 - 2)
BAT (default)
(2 - 3)
Clear-CMOS
Table A.3: CN39, COM2 Setting
1
2
1
2
1
2
3
4
3
4
3
4
5
6
5
6
5
6
Part Number
1653003260
Footprint
JH3X2S-2M
Description
PIN HEADER 3*2P 180D SMDMALE SQUARE PIN
2.0mm
Setting
Function
(1 - 2)
RS232
(3 - 4)
RS485
(5 - 6)
RS422
PCM-4153 User Manual
46
Part Number
1653003101
Footprint
JH3X1V-2M
Description
PIN HEADER 3*1P 180D(M) 2.0 mm DIP SQUARE W/O Pb
Setting
Function
(1-2)
Slave (default)
(2-3)
Master
Table A.5: J5, PCI VI/O POWER
Part Number
1653003101
Footprint
JH3X1V-2M
Description
PIN HEADER 3*1P
180D (M)SQUARE 2.0mm
Setting
Function
(1 - 2)
With +5 V
(2 - 3)
With +3.3 V
Table A.6: CN38, Power Input
8
1
Part Number
1655204030
Footprint
PWR-B4PV
Description
PIN HEADER DIP 8*1P 180D(M) 2.00mm
Pin
Pin Name
Signal Type
Signal Level
1
+5 V
PWR
+5 V
2
+5 V
PWR
+5 V
3
+5 V
PWR
+5 V
4
GND
GND
-
5
GND
GND
-
6
GND
GND
-
7
GND
GND
-
8
+12 V
PWR
+12 V
47
PCM-4153 User Manual
Appendix A Pin Assignments
Table A.4: J4-Flash select
Table A.7: CN4, TFT LCD I/F
Part Number
1653920200
Footprint
SPH20X2
Description
*CONN. DF13-40DP-1.25 V
Pin
Pin Name
Signal Type
Signal Level
1
+5 V
PWR
+5 V
2
+5 V
PWR
+5 V
3
GND
GND
-
4
GND
GND
-
5
+3.3V
PWR
+3.3 V
6
+3.3V
PWR
+3.3 V
7
TV-CLK
CLK48M
+3.3 V
8
GND
GND
-
9
D0
I/O
+5 V
10
D1
I/O
+5 V
11
D2
I/O
+5 V
12
D3
I/O
+5 V
13
D4
I/O
+5 V
14
D5
I/O
+5 V
15
D6
I/O
+5 V
16
D7
I/O
+5 V
17
D8
I/O
+3.3 V
18
D9
I/O
+5 V
19
D10
I/O
+5 V
20
D11
I/O
+5 V
21
D12
I/O
+5 V
22
D13
I/O
+5 V
23
D14
I/O
+5 V
24
D15
I/O
+5 V
25
D16
I/O
+3.3V
26
D17
I/O
+3.3 V
27
D18
I/O
+3.3 V
28
D19
I/O
+3.3 V
29
D20
I/O
+3.3 V
30
D21
I/O
+3.3 V
31
D22
I/O
+3.3 V
32
D23
I/O
+3.3 V
33
GND
GND
-
34
GND
GND
-
35
DOTCLK
CLK
+3.3 V
36
VS
OUT
+3.3 V
37
DE
I/O
+3.3 V
PCM-4153 User Manual
48
HS
OUT
+3.3 V
39
RST
OUT
+3.3 V
40
FP
OUT
+3.3 V
Table A.8: CN5, Inverter Power
5
4
3
2
1
Part Number
1655305020
Footprint
WHL5V-2M
Description
WAFER BOX 2.0 mm 5P 180D MALE W/LOCK
Pin
Pin Name
Signal Type
Signal Level
1
+12 V
PWR
+12 V
2
GND
GND
-
3
ENABKL
OUT
+3.3 V
4
VBR
OD
+3.3 V
5
+5 V
PWR
+5 V
Table A.9: CN6, SMBus
2
1
Part Number
1653002101
Footprint
JH2X1V-2M
Description
PIN HEADER 2*1P 180D (M)SQUARE 2.0 mm
Pin
Pin Name
Signal Type
Signal Level
1
SMB-CLK
CLK
+3V
2
SMB-DAT
I/O
+3V
Table A.10: CN32, Reset / Buzzer pin header
6
4
2
5
3
1
Part Number
1655302020
Footprint
WHL2V-2M
Description
PIN HEADER DIP 3*2P
Pin
Pin Name
Signal Type
Signal Level
1
-
GND
-
2
-
IN
+3.3 V
3
GND
GND
-
4
RST
IN
-3.3 V
5
Buzzer -
-
-
6
Buzzer +
-
-
49
180D(M) 2.00 mm
PCM-4153 User Manual
Appendix A Pin Assignments
38
Table A.11: CN33-Battery Connector
Pin
Function
1
VBAT power
2
GND
Table A.12: CN36, GPIO1
5
4
3
2
1
Part Number
1653005261
Footprint
JH5X2S-2M
Description
PIN HEADER SMD 5*1P 180D(M) 2.54mm
Pin
Pin Name
Signal Type
Signal Level
1
+5V
PWR
+5 V
2
GPIO0
I/O
+5 V
3
GPIO1
I/O
+5 V
4
GPIO2
I/O
+5 V
5
GPIO3
I/O
+5 V
Table A.13: CN37, GPIO2
5
4
3
2
1
Part Number
1653005261
Footprint
JH5X2S-2M
Description
PIN HEADER SMD 5*1P 180D(M) 2.54mm
Pin
Pin Name
Signal Type
Signal Level
1
GPIO4
I/O
+5V
2
GPIO5
I/O
+5V
3
GPIO6
I/O
+5V
4
GPIO7
I/O
+5V
5
GND
-
-
Table A.14: CN11, IDE
Part Number
1653222262
Footprint
BH22X2SV
Description
BOX HEADER SMD 22*2P 180D(M) 2.0 mm IDIOT-PROOF
Pin
Pin Name
Signal Type
Signal Level
1
RST#
Out
+5V
PCM-4153 User Manual
50
GND
GND
-
3
D7
I/O
+5V
4
D8
I/O
+3.3V
5
D6
I/O
+5V
6
D9
I/O
+5V
7
D5
I/O
+5V
8
D10
I/O
+5V
9
D4
I/O
+5V
10
D11
I/O
+5V
11
D3
I/O
+5V
12
D12
I/O
+5V
13
D2
I/O
+5V
14
D13
I/O
+5V
15
D1
I/O
+5V
16
D14
I/O
+5V
17
D0
I/O
+5V
18
D15
I/O
+5V
19
GND
GND
-
21
DREQ
Out
+5V
22
GND
GND
-
23
IOW#
Out
+5V
24
GND
GND
-
25
IOR#
Out
+5V
26
GND
GND
-
27
IORDY
Out
+5V
28
CSEL#
Out
+5V
29
DACK#
Out
+5V
30
GND
GND
-
31
IRQ14
In
+5V
32
NC
-
-
33
A1
In
+5V
34
D66DET#
In
+5V
35
A0
In
+5V
36
A2
In
+5V
37
CS#1
Out
+5V
38
CS#3
Out
+5V
39
ASP#
Out
+5V
40
GND
GND
-
41
+5V
PWR
+5V
42
+5V
PWR
+5V
43
GND
GND
-
44
NC
-
-
51
PCM-4153 User Manual
Appendix A Pin Assignments
2
Table A.15: CN27, CRT
1654515304
Footprint
DBVGA-VF5M
12
1
Part Number
Description
CONN. 12P 90D(F) SMD 1.25 mm
Pin
Pin Name
Signal Type
Signal Level
1
GND
GND
-
2
R
OUT
Analog
3
G
OUT
Analog
4
B
OUT
Analog
5
GND
GND
-
6
+5V
PWR
-
7
DDAT
OD I/O
+2.5 V
8
DCLK
OD I/O
+2.5 V
9
GND
GND
-
10
HSYNC
OUT
+2.5 V
11
VSYNC
OUT
+2.5 V
12
GND
-
-
Table A.16: CN15, USB1/2
Part Number
1653005260
Footprint
JH5X2S-2M
10
5
9
8
4
3
7
2
6
1
Description
PIN HEADER 5*2P 180D(M) 2.0 mm SMD IDIOT-PROOF
Pin
Pin Name
Signal Type
Signal Level
1
+5V
PWR
+5V
2
+5V
PWR
+5V
3
P0-
I/O
USB
4
P1-
I/O
USB
5
P0+
I/O
USB
6
P1+
I/O
USB
7
GND
GND
-
8
GND
GND
-
9
GND
GND
-
10
NC
-
-
PCM-4153 User Manual
52
10
5
9
8
4
3
7
2
6
1
Part Number
1653005260
Footprint
JH5X2S-2M
Description
PIN HEADER 5*2P 180D(M) 2.0 mm SMD IDIOT-PROOF
Pin
Pin Name
Signal Type
Signal Level
1
+5V
PWR
+5V
2
+5V
PWR
+5V
3
P2-
I/O
USB
4
P3-
I/O
USB
5
P2+
I/O
USB
6
P3+
I/O
USB
7
GND
GND
-
8
GND
GND
-
9
GND
GND
-
10
NC
-
-
Table A.18: CN30, COM1/2/3/4
39 37
3
1
40 38
4
2
Part Number
1653000221
Footprint
BH20X2SV-2.00 mm
Description
Pin
Pin Name
Signal Type
Signal Level
1
DCD#1
IN
+5V
2
DSR#1
IN
+5V
3
RXD1
IN
+5V
4
RTS#1
I/O
+5V
5
TXD1
OUT
+5V
6
CTS#1
IN
+5 V
7
DTR#1
I/O
+5 V
8
RI#1
IN
+5 V
9
GND
GND
-
10
GND
GND
-
11
DCD#2
In
+5 V
12
DSR#2
In
+5 V
13
RXD2
In
+5 V
14
RTS#2
I/O
+5 V
15
TXD2
Out
+5 V
16
CTS#2
In
+5 V
17
DTR#2
I/O
+5 V
53
PCM-4153 User Manual
Appendix A Pin Assignments
Table A.17: CN17, USB3/4
18
RI#2
In
+5 V
19
GND
GND
-
20
GND
GND
-
21
DCD#3
In
+5 V
22
DSR#3
In
+5 V
23
RXD3
In
+5 V
24
RTS#3
I/O
+5 V
25
TXD3
Out
+5 V
26
CTS#3
In
+5 V
27
DTR#3
I/O
+5 V
28
RI#3
In
+5 V
29
GND
GND
-
30
GND
GND
-
31
DCD#4
In
+5 V
32
DSR#4
In
+5 V
33
RXD4
In
+5 V
34
RTS#4
I/O
+5 V
35
TXD4
Out
+5 V
36
CTS#4
In
+5 V
37
DTR#4
I/O
+5 V
38
RI#4
In
+5 V
39
GND
GND
-
40
GND
-
-
Table A.19: CN19, Print Port
25 23
3 1
26 24
4 2
Part Number
1653000272
Footprint
BH13x2SV-2.00
Description
BOX HEADER SMD 13*2P 180D(M) 2.0 mm
Pin
Pin Name
Signal Type
Signal Level
1
STB#
Out
+5 V
2
AFD#
Out
+5 V
3
PD0
I/O
+5 V
4
ERR#
In
+5 V
5
PD1
I/O
+5 V
6
INIT#
Out
+5 V
7
PD2
I/O
+5 V
8
SLIN#
Out
+5 V
9
PD3
I/O
+5 V
10
GND
GND
-
11
PD4
I/O
+5 V
12
GND
GND
-
13
PD5
I/O
+5 V
14
GND
GND
-
PCM-4153 User Manual
54
PD6
I/O
+5 V
16
GND
GND
-
17
PD7
I/O
+5 V
18
GND
GND
-
19
ACK#
In
+5 V
20
GND
GND
-
21
BUSY
In
+5 V
22
GND
GND
-
23
PE
In
+5 V
24
GND
GND
-
25
SLCT
In
+5 V
26
NC
-
-
Table A.20: CN20, RS422/485
4
3
2
1
Part Number
1653004101
Footprint
JH4X1V-2M
Description
PIN HEADER 4*1P 180D(M) SQUARE 2.0 mm
Pin
Pin Name
Signal Type
Signal Level
1
422-RXD-
In
+5 V
2
422-RXD+
In
+5 V
3
485-422-TXD+
Out
+5 V
4
485-422-TXD-
Out
+5 V
Table A.21: CN35, AUDIO-OUT
3
2
1
Part Number
1655303020
Footprint
WHL3V-2M
Description
WAFER BOX 2.0 mm 3P 180D w/LOCK
Pin
Pin Name
Signal Type
Signal Level
1
LIN-OUT-R
OUT
Analog
2
GND
GND
-
3
LIN-OUT-L
Out
Analog
55
PCM-4153 User Manual
Appendix A Pin Assignments
15
Table A.22: CN34, AUDIO-IN
5
4
3
2
1
Part Number
1655303020
Footprint
WHL3V-2M
Description
WAFER BOX 2.0 mm 3P 180D w/LOCK
Pin
Pin Name
Signal Type
Signal Level
1
LIN-IN-R
IN
Analog
2
GND
GND
-
3
LIN-IN-L
IN
Analog
4
GND
GND
-
5
MIC-IN
IN
Analog
Table A.23: CN23, ISA -5V & -12V Input
3
2
1
Part Number
1653003101
Footprint
JH3X1V-2M
Description
PIN HEADER 3*1P 180D (M)SQUARE 2.0 mm
Pin
Pin Name
Signal Type
Signal Level
1
-12V
PWR
-12V
2
-5V
PWR
-5V
3
GND
GND
-
Table A.24: CN25, LAN1
2 4
1
6 8 10
3 5 7 9
Part Number
1653205260
Footprint
BH5X2SV
Description
BOX HEADER SMD 5*2 180D (M) 2.0 mm
Pin
Pin Name
Signal Type
Signal Level
1
+3.3 VL
PWR
+3.3 V
2
LAN1-ACTLED
IN
Analog
3
LAN1-RX+
IN
Analog
4
LAN1-RX-
IN
Analog
5
LAN1-LILED
IN
Analog
6
LAN2-LCT
I/O
Analog
7
N/A
-
-
8
LAN2-LCT
I/O
Analog
9
LAN1-TX+
OUT
Analog
10
LAN1-TX-
OUT
Analog
PCM-4153 User Manual
56
2 4
1
6 8 10
3 5 7 9
Part Number
1653205260
Footprint
BH5X2SV
Description
BOX HEADER SMD 5*2 180D (M) 2.0 mm
Pin
Pin Name
Signal Type
Signal Level
1
+3.3 V
PWR
+3.3 V
2
LAN2-ACTLED
IN
Analog
3
LAN2-RX+
IN
Analog
4
LAN2-RX-
IN
Analog
5
LAN2-LILED
IN
Analog
6
LAN2-LCT
I/O
Analog
7
N/A
-
-
8
LAN2-LCT
I/O
Analog
9
LAN2-TX+
OUT
Analog
10
LAN2-TX-
OUT
Analog
Table A.26: CN18, KB/MS
6
5
4
3
2
1
Part Number
1653205260
Footprint
BH5X2SV
Description
BOX HEADER DIP 6*1 180D (M) 2.0 mm
Pin
Pin Name
Signal Type
Signal Level
1
KB-CLK
IN
+5 V
2
KB-DATA
IN
+5 V
3
MS-CLK
IN
+5 V
4
GND
PWR
-
5
+5 V
PWR
+5 V
6
MS-DATA
IN
+5 V
57
PCM-4153 User Manual
Appendix A Pin Assignments
Table A.25: CN26, LAN2
PCM-4153 User Manual
58
Appendix
B
B
System Assignments
This appendix contains information of a detailed nature.
Sections includes:
 System I/O ports
 1st MB memory map
 DMA channel assignments
 Interrupt assignments
B.1 System I/O Ports
Table B.1: System I/O Ports
Addr. range (Hex)
Device
000-01F
DMA controller
020-021
Interrupt controller 1, master
040-05F
8254 timer
060-06F
8042 (keyboard controller)
070-07F
Real-time clock, non-maskable interrupt (NMI) mask
080-09F
DMA page register
0A0-0BF
Interrupt controller 2
0C0-0DF
DMA controller
0F0
Clear math co-processor
0F1
Reset math co-processor
0F8-0FF
Math co-processor
1F0-1F8
Fixed disk
200-207
Reserved (Game I/O)
278-27F
Reserved (Parallel port 2,LTP3)
2E8-2EF
Reserved (Series port 4)
2F8-2FF
Serial port 2
300-31F
Prototype card
360-36F
Reserved
378-37F
Parallel printer port 1 (LPT 2)
380-38F
SDLC, bisynchronous 2
3A0-3AF
Bisynchronous 1
3B0-3BF
Monochrome display and printer adapter (LPT1)
3C0-3CF
Reserved
3D0-3DF
Color/graphics monitor adapter
3E8-3EF
Reserved (Series port 3)
3F0-3F7
Diskette controller
3F8-3FF
Serial port 1
* PNP audio I/O map range from 220 ~ 250H (16 bytes)
MPU-401 select from 300 ~ 330H (2 bytes)
PCM-4153 User Manual
60
Table B.2: 1st MB Memory Map
Addr. range (Hex)
Device
F0000h - FFFFFh
System ROM
*CC000h - EFFFFh
Unused (reserved for Ethernet ROM)
C0000h - CBFFFh
Expansion ROM (for VGA BIOS)
B8000h - BFFFFh
CGA/EGA/VGA text
B0000h - B7FFFh
Unused
A0000h - AFFFFh
EGA/VGA graphics
00000h - 9FFFFh
Base memory
* If Ethernet boot ROM is disabled (Ethernet ROM occupies about 16 KB)
* E0000 - EFFFF is reserved for BIOS POST
B.3 DMA Channel Assignments
Table B.3: DMA Channel Assignments
Channel
Function
0
Available
1
Available (audio)
2
Floppy disk (8-bit transfer)
3
Available (parallel port)
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
* Audio DMA select 1, 3, or 5
** Parallel port DMA select 1 (LPT2) or 3 (LPT1)
61
PCM-4153 User Manual
Appendix B System Assignments
B.2 1st MB Memory Map
B.4 Interrupt Assignments
Table B.4: Interrupt Assignments
Interrupt#
Interrupt source
IRQ 0
Interval timer
IRQ 1
Keyboard
IRQ 2
Interrupt from controller 2 (cascade)
IRQ 3
COM2
IRQ 4
COM1
IRQ 5
Reserved (COM4)
IRQ 6
FDD
IRQ 7
LPT1
IRQ 8
RTC
IRQ 9
Reserved (audio)
IRQ 10
Reserved (COM3)
IRQ 11
Reserved for watchdog timer
IRQ 12
PS/2 mouse
IRQ 13
INT from co-processor
IRQ 14
Primary IDE
IRQ 15
Secondary IDE for CFC
* Ethernet interface IRQ select: 9, 11, 15
* PNP audio IRQ select: 9, 11, 15
* PNP USB IRQ select: 9, 11, 15
* PNP ACPI IRQ select: 9, 11, 15
PCM-4153 User Manual
62
Appendix
C
C
Mechanical Drawings
C.1 Mechanical Drawings
0.00
90.17
Figure C.1 PCM-4153 Mech drawing (comp side)
95.89
87.63
87.63
62.91
8.26
8.26
102.87
90.17
0.00
12.70
97.69
0.00
Figure C.2 PCM-4153 mech drawing (sol side)
PCM-4153 User Manual
64
Appendix
D
Prog. GPIO &
Watchdog Timer
D
D.1 GPIO Function: Its Call by Int15 Hook.
GPIO configuration register:
Input_Reg
EQU 00h
Output_Reg
EQU 01h
Inversion_Reg
EQU 02h
Configure_Reg
EQU 03h
-------------------------------------------------------Bh means int15 function you want to call:
Bh = 01h ; Get GPIO config
Bh = 02h ; Set GPIO config
Bh = 03h ; Get GPIO Status
Bh = 04h ; Set GPIO Status
-------------------------------------------------------Sample code :
;===============================================================
;
Set GPIO Config
; Input:
;
ax=5E87h
;
bh=02h
;
cl= n ; n means which group of GPIO you want to set
;
bl= the n group of gpio config
;
bit 0 = gpio 0 , 0 => output pin; 1 => input pin
;
bit 1 = gpio 1 , 0 => output pin; 1 => input pin
;
.....
;
bit 7 = gpio 7 , 0 => output pin; 1 => input pin
; output:
;
ax=5E78
;function success, other value means function fail
;===============================================================
mov
ax, 5E87H ;int15 hook as 5E87H
mov bh,02h
mov cl,Configure_Reg
mov al, bl ;( bl = bit0~7 = GPIO0~7 : 0 => output pin; 1 => input pin)
call
Ct_I2CWriteByte
mov ax,5E78h
;return function success
;===============================================================
;
Set GPIO status
; Input:
;
ax=5E87h
;
bh=04h
;
cl= n ; n means which group of GPIO you want to set
;
bl= the n group of gpio status
;
bit 0 = gpio 0 , 0 => Low; 1 => High
;
bit 1 = gpio 1 , 0 => Low; 1 => High
;
.....
PCM-4153 User Manual
66
D.2 Watchdog Timer:
;The SCH3114 Runtime base I/O address is 800h
;Setting WatchDog time value location at offset 66h
;If set value "0", it is mean disable WatchDog function.
Superio_GPIO_Port = 800h
mov dx,Superio_GPIO_Port + 66h
mov al,00h
out dx,al
.model small
.486p
.stack 256
.data
SCH3114_IO EQU 800h
.code
org 100h
.STARTup
;====================================================
;90H
;enable WDT function bit [0]=01h
;====================================================
mov dx,SCH3114_IO + 90h
mov al,01h
out dx,al
;====================================================
;65H
;bit [1:0]=Reserved
;bit [6:2]Reserve=00000
;bit [7] WDT time-out Value Units Select
;Minutes=0 (default) Seconds=1
;====================================================
mov dx,SCH3114_IO + 65h ;
mov al,080h
out dx,al
;====================================================
67
PCM-4153 User Manual
Appendix D Prog. GPIO & Watchdog Timer
;
bit 7 = gpio 7 , 0 => Low; 1 => High
; output:
;
ax=5E78
;function success, other value means function fail
;===============================================================
=
mov
ax, 5E87H ;int15 hook as 5E87H
mov bh, 04h ;Set GPIO status
mov cl, Output_Reg
mov al, bl ;( bl = bit0~7 = GPIO0~7 : 0 => Low; 1 => High)
call
Ct_I2CWriteByte
mov ax,5E87h ;return function success
;66H
;WDT timer time-out value
;bit[7:0]=0~255
;====================================================
mov dx,SCH3114_IO + 66h
mov al,01h
out dx,al
;====================================================
;bit[0] status bit R/W
;WD timeout occurred =1
;WD timer counting = 0
;====================================================
mov dx,SCH3114_IO + 68h
mov al,01h
out dx,al
.exit
END
PCM-4153 User Manual
68
Appendix D Prog. GPIO & Watchdog Timer
PCM-4153 User Manual
69
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement