Nexcom ICES 668 Manual
NEXCOM International Co., Ltd.
Industrial Computing Solutions
COM Express Type 6
ICEK 668-T6 (ICES 668 Series and ICEB 8060)
Starter Kit User Manual
NEXCOM International Co., Ltd.
Published May 2013
www.nexcom.com
Content
Contents
Preface
Block Diagram.........................................................................................8
ICES 668..............................................................................................8
ICEB 8060............................................................................................9
Copyright .............................................................................................. iv
Disclaimer............................................................................................... iv
Acknowledgements................................................................................ iv
Regulatory Compliance Statements......................................................... iv
Declaration of Conformity....................................................................... iv
RoHS Compliance.................................................................................... v
Warranty and RMA................................................................................. vi
Safety Information.................................................................................viii
Installation Recommendations................................................................viii
Safety Precautions................................................................................... ix
Technical Support and Assistance............................................................. x
Conventions Used in this Manual............................................................. x
Global Service Contact Information......................................................... xi
Package Contents..................................................................................xiii
Ordering Information.............................................................................xiv
Chapter 2: Jumpers and Connectors
Before You Begin...................................................................................10
Precautions ...........................................................................................10
Jumper Settings.....................................................................................11
Locations of the Jumpers and Connectors for ICES 668..........................12
Connector Pin Definitions......................................................................13
Internal Connectors............................................................................13
DDR3_SEL and F82126 ADDRESS SEL DIP SW SIGNAL.....................13
PCIe DIP Switch...............................................................................13
CPU Fan Connector.........................................................................14
High Speed Board-to-Board Connector:
Row A and B, Row C and D............................................................15
Locations of the Jumpers and Connectors for ICEB 8060........................20
Jumpers.................................................................................................21
3.5G Module......................................................................................21
LVDS Power Select (3.3V/5V)..............................................................21
Termal Select......................................................................................22
GPIO Power Select..............................................................................22
Power Mode Select.............................................................................23
RTC Clear...........................................................................................23
Fintek TX/RX Pin Header.....................................................................24
DIP Switch Settings................................................................................25
Close to U4........................................................................................25
Chapter 1: Product Introduction
Overview - ICES 668................................................................................1
Key Features............................................................................................1
Hardware Specifications...........................................................................2
Knowing Your ICES 668...........................................................................3
Overview - ICEB 8060..............................................................................4
Key Features............................................................................................4
Hardware Specifications...........................................................................5
Knowing Your ICEB 8060.........................................................................7
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
ii
ICEK 668-T6 Starter Kit User Manual
Content
PEG x16 Slot...................................................................................44
Digital Display Interface (Port B/ DDI #1)..........................................46
PCIe x4...........................................................................................48
PCIe x1 Slots...................................................................................49
Mini-PCIe Slot (Wi-Fi and 3G)..........................................................50
Mini-PCIe Slot (mSATA)...................................................................51
SIM Card Slot..................................................................................52
High Speed Board-to-Board Connector:
Row A and B, Row C and D............................................................53
RS232/ RS422/ RS485 Mode Select.....................................................25
BIOS Select.........................................................................................26
Connector Pin Definitions......................................................................27
External Connectors...........................................................................27
VGA and COM2 Ports.....................................................................27
LAN and USB Ports..........................................................................28
DisplayPort......................................................................................29
Audio Connectors...........................................................................30
Internal Connectors............................................................................31
HDD LED.........................................................................................31
Internal Speaker..............................................................................31
COM2 RS232 RI# Pin Power Select..................................................32
GAL Download Port........................................................................32
SPI..................................................................................................33
Disable EEPROM..............................................................................33
Keyboard and Mouse Pin Header....................................................34
HW Reset Function..........................................................................34
Power Button..................................................................................35
GPIO...............................................................................................35
USB Port 6 and 7.............................................................................36
USB Port 5......................................................................................36
CCFL...............................................................................................37
LVDS Channel A..............................................................................37
LVDS Channel B..............................................................................38
COM1 Port Box Header...................................................................38
COM3 Port Box Header...................................................................39
COM4 Port Box Header...................................................................39
COM5 Port Box Header...................................................................40
COM6 Port Box Header...................................................................40
Battery Charger...............................................................................41
Fan Connector................................................................................41
4-Pin Power Connector...................................................................42
ATX Power Connector.....................................................................42
SATA3.0 Connectors.......................................................................43
CFast Slot........................................................................................43
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup
Setting up the System............................................................................58
External Soft-Power On/Off and Hardware Reset Switches.....................64
Closing the Case....................................................................................65
Chapter 4: BIOS Setup
About BIOS Setup..................................................................................66
When to Configure the BIOS..................................................................66
Default Configuration............................................................................67
Entering Setup.......................................................................................67
Legends.................................................................................................67
BIOS Setup Utility...................................................................................69
Main..................................................................................................69
Advanced...........................................................................................70
Chipset...............................................................................................81
Boot...................................................................................................86
Security..............................................................................................86
Save & Exit.........................................................................................87
Appendix A: Watchdog Timer................................88
WDT Programming Guide......................................................................88
Appendix B: GPI/O Programming Guide...............90
iii
ICEK 668-T6 Starter Kit User Manual
Preface
Preface
Copyright
Regulatory Compliance Statements
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without the prior written consent from NEXCOM
International Co., Ltd.
This section provides the FCC compliance statement for Class B devices and
describes how to keep the system CE compliant.
Declaration of Conformity
FCC
Disclaimer
This equipment has been tested and verified to comply with the limits for
a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
(domestic environment) is likely to cause harmful interference, in which
case the user will be required to correct the interference (take adequate
measures) at their own expense.
The information in this document is subject to change without prior notice and
does not represent commitment from NEXCOM International Co., Ltd. However,
users may update their knowledge of any product in use by constantly checking
its manual posted on our website: http://www.nexcom.com. NEXCOM shall
not be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use of any product, nor for any infringements upon the rights
of third parties, which may result from such use. Any implied warranties of
merchantability or fitness for any particular purpose is also disclaimed.
Acknowledgements
CE
The product(s) described in this manual complies with all applicable
European Union (CE) directives if it has a CE marking. For computer systems
to remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.
ICEK 668-T6 is a trademark of NEXCOM International Co., Ltd. All other
product names mentioned herein are registered trademarks of their
respective owners.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
iv
ICEK 668-T6 Starter Kit User Manual
Preface
RoHS Compliance
How to recognize NEXCOM RoHS Products?
NEXCOM RoHS Environmental Policy and Status
Update
For existing products where there are non-RoHS and RoHS versions, the
suffix “(LF)” will be added to the compliant product name.
This publication, including all photographs, illustrations
and software, is protected under international copyright
laws, with all rights reserved. No part of this manual
may be reproduced, copied, translated or transmitted in any form or by any
means without the prior written consent from NEXCOM International Co.,
Ltd.
All new product models launched after January 2006 will be RoHS compliant.
They will use the usual NEXCOM naming convention.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1%
or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent Chromium
(Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) < 0.1% or
1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm.
In order to meet the RoHS compliant directives, NEXCOM has established
an engineering and manufacturing task force to implement the introduction
of green products. The task force will ensure that we follow the standard
NEXCOM development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NEXCOM are renowned.
The model selection criteria will be based on market demand. Vendors and
suppliers will ensure that all designed components will be RoHS compliant.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
v
ICEK 668-T6 Starter Kit User Manual
Preface
Warranty and RMA
NEXCOM Warranty Period
Repair Service Charges for Out-of-Warranty Products
NEXCOM manufactures products that are new or equivalent to new in
accordance with industry standard. NEXCOM warrants that products will
be free from defect in material and workmanship for 2 years, beginning on
the date of invoice by NEXCOM. HCP series products (Blade Server) which
are manufactured by NEXCOM are covered by a three year warranty period.
NEXCOM will charge for out-of-warranty products in two categories, one is
basic diagnostic fee and another is component (product) fee.
Repair Service Charges for Out-of-Warranty Products
NEXCOM will charge for out-of-warranty products in two categories, one is
basic diagnostic fee and another is component (product) fee.
NEXCOM Return Merchandise Authorization (RMA)
▪▪ Customers shall enclose the “NEXCOM RMA Service Form” with the
returned packages.
System Level
▪▪ Component fee: NEXCOM will only charge for main components such as
SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistor, capacitor.
▪▪ Customers must collect all the information about the problems
encountered and note anything abnormal or, print out any on-screen
messages, and describe the problems on the “NEXCOM RMA Service
Form” for the RMA number apply process.
▪▪ Items will be replaced with NEXCOM products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
▪▪ Customers can send back the faulty products with or without accessories
(manuals, cable, etc.) and any components from the card, such as CPU
and RAM. If the components were suspected as part of the problems,
please note clearly which components are included. Otherwise, NEXCOM
is not responsible for the devices/parts.
▪▪ Replace with 3rd party products if needed.
▪▪ If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.
Board Level
▪▪ Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
▪▪ Component fee: NEXCOM will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistors, capacitors.
▪▪ If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.
▪▪ Any products returned by NEXCOM to other locations besides the
customers’ site will bear an extra charge and will be billed to the customer.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
vi
ICEK 668-T6 Starter Kit User Manual
Preface
Warnings
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are inconsistent
with these instructions or the instructions for accessory modules, contact
the supplier to find out how you can ensure that your computer meets
safety and regulatory requirements.
Cautions
Electrostatic discharge (ESD) can damage system components. Do the
described procedures only at an ESD workstation. If no such station is
available, you can provide some ESD protection by wearing an antistatic
wrist strap and attaching it to a metal part of the computer chassis.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
vii
ICEK 668-T6 Starter Kit User Manual
Preface
Safety Information
Installation Recommendations
Before installing and using the device, note the following precautions:
Ensure you have a stable, clean working environment. Dust and dirt can get
into components and cause a malfunction. Use containers to keep small
components separated.
▪▪ Read all instructions carefully.
▪▪ Do not place the unit on an unstable surface, cart, or stand.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
▪▪ Follow all warnings and cautions in this manual.
▪▪ When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪▪ A Philips screwdriver
▪▪ A flat-tipped screwdriver
▪▪ Avoid using the system near water, in direct sunlight, or near a heating
device.
▪▪ A grounding strap
▪▪ The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪▪ An anti-static pad
Using your fingers can disconnect most of the connections. It is recommended
that you do not use needle-nose pliers to disconnect connections as these
can damage the soft metal or plastic parts of the connectors.
▪▪ The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
viii
ICEK 668-T6 Starter Kit User Manual
Preface
Safety Precautions
11.If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
1.Read these safety instructions carefully.
2.Keep this User Manual for later reference.
12.Never pour any liquid into an opening. This may cause fire or electrical
shock.
3.Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
13.Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
4.For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
14.If one of the following situations arises, get the equipment checked by
service personnel:
a.The power cord or plug is damaged.
b.Liquid has penetrated into the equipment.
c.The equipment has been exposed to moisture.
d.The equipment does not work well, or you cannot get it to work
according to the user’s manual.
e.The equipment has been dropped and damaged.
f.The equipment has obvious signs of breakage.
5.Keep this equipment away from humidity.
6.Put this equipment on a stable surface during installation. Dropping it or
letting it fall may cause damage.
7.The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
15.Do not place heavy objects on the equipment.
8.Make sure the voltage of the power source is correct before connecting
the equipment to the power outlet.
16.The unit uses a three-wire ground cable which is equipped with a third
pin to ground the unit and prevent electric shock. Do not defeat the
purpose of this pin. If your outlet does not support this kind of plug,
contact your electrician to replace your obsolete outlet.
9.Place the power cord in a way so that people will not step on it. Do not
place anything on top of the power cord. Use a power cord that has been
approved for use with the product and that it matches the voltage and
current marked on the product’s electrical range label. The voltage and
current rating of the cord must be greater than the voltage and current
rating marked on the product.
17.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
10. All cautions and warnings on the equipment should be noted.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
ix
ICEK 668-T6 Starter Kit User Manual
Preface
Technical Support and Assistance
Conventions Used in this Manual
1. For the most updated information of NEXCOM products, visit NEXCOM’s
website at www.nexcom.com.
Warning:
Information about certain situations, which if not observed,
can cause personal injury. This will prevent injury to yourself
when performing a task.
2.For technical issues that require contacting our technical support team or
sales representative, please have the following information ready before
calling:
– Product name and serial number
– Detailed information of the peripheral devices
–Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
CAUTION!
Caution:
Information to avoid damaging components or losing data.
Note:
Provides additional information to complete a task easily.
Warning!
1.Handling the unit: carry the unit with both hands and handle it with care.
2.Maintenance: to keep the unit clean, use only approved cleaning products
or clean with a dry cloth.
3.CompactFlash: Turn off the unit’s power before inserting or removing a
CompactFlash storage card.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
x
ICEK 668-T6 Starter Kit User Manual
Preface
Global Service Contact Information
Headquarters
NEXCOM International Co., Ltd.
15F, No. 920, Chung-Cheng Rd.,
ZhongHe District, New Taipei City, 23586,
Taiwan, R.O.C.
Tel: +886-2-8226-7786
Fax: +886-2-8226-7782
www.nexcom.com
America
USA
NEXCOM USA
2883 Bayview Drive,Fremont CA 94538,
USA
Tel: +1-510-656-2248
Fax: +1-510-656-2158
Email: [email protected]
www.nexcom.com
Asia
Taiwan
Central Taiwan Office
16F, No.250, Sec. 2, Chongde Rd., Beitun Dist., Taichung City 406, R.O.C.
Tel: +886-4-2249-1179
Fax: +886-4-2249-1172
Email: [email protected]
www.nexcom.com.tw
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Japan
NEXCOM Japan
Nanjing Office
9F, Tamachi Hara Bldg.,4-11-5, Shiba Minato-ku,
Tokyo, 108-0014, Japan
Tel: +81-3-5419-7830
Fax: +81-3-5419-7832
Email: [email protected]
www.nexcom-jp.com
China
NEXCOM China
Hall C, Block 17, Tian Xing Cui Lang Bldg.,
No. 49 Yunnan North Rd.,
Nanjing, 210018, China
Tel: +86-25-8315-3486
Fax: +86-25-8315-3489
Email: [email protected]
www.nexcom.cn
Shenzhen Office
2F, Block 4, Venus Plaza, Bldg. 21,
ZhongGuanCun Software Park, No. 8,
Dongbeiwang West Rd., Haidian District,
Beijing, 100193, China
Tel: +86-10-8282-5880
Fax: +86-10-8282-5955
Email: [email protected]
www.nexcom.cn
Western Room 708, Block 210,
Tairan Industry & Trading Place,
Futian Area, Shenzhen,
518040, China
Tel: +86-755-8332-7203
Fax: +86-755-8332-7213
Email: [email protected]
www.nexcom.cn
Wuhan Office
Shanghai Office
Room 1505, Greenland He Chuang Bldg.,
No. 450 Caoyang Rd.,
Shanghai, 200062, China
Tel: +86-21-6150-8008
Fax: +86-21-3251-6358
Email: [email protected]
www.nexcom.cn
xi
1-C1804/ 1805, Mingze Liwan,
No. 519 South Luoshi Rd.,
Hongshan District, Wuhan, 430070, China
Tel: +86-27-8722-7400
Fax: +86-27-8722-7400
Email: [email protected]
www.nexcom.cn
ICEK 668-T6 Starter Kit User Manual
Preface
Chengdu Office
Italy
9F, Shuxiangxie, Xuefu Garden,
No.12 Section 1, South Yihuan Rd.,
Chengdu, 610061, China
Tel: +86-28-8523-0186
Fax: +86-28-8523-0186
Email: [email protected]
www.nexcom.cn
NEXCOM ITALIA S.r.l
Via Gaudenzio Ferrari 29,
21047 Saronno (VA), Italia
Tel: +39 02 9628 0333
Fax: +39 02 9286 9215
Email: [email protected]
www.nexcomitalia.it
Europe
United Kingdom
NEXCOM EUROPE
France
NEXCOM France
La Grande Arche-Paroi Nord,
92044 Paris La Défense, France
Tel: +33 (0) 1 40 90 33 35
Fax: +33 (0) 1 40 90 31 01
Email: [email protected]
www.nexcom.eu
10 Vincent Avenue,
Crownhill Business Centre,
Milton Keynes, Buckinghamshire MK8 0AB,
United Kingdom
Tel: +44-1908-267121
Fax: +44-1908-262042
Email: [email protected]
www.nexcom.eu
Germany
NEXCOM GmbH
Leopoldstraße Business Centre,
Leopoldstraße 244,
80807 Munich, Germany
Tel: +49-89-208039-278
Fax: +49-89-208039-279
Email: [email protected]
www.nexcom.eu
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
xii
ICEK 668-T6 Starter Kit User Manual
Preface
Package Contents
Before continuing, verify that the ICEK 668-T6 package that you received is complete. Your package should have all the items listed in the following table.
Item
1
2
3
4
5
Description
ICES 668
ICEB 8060
Built-in 10.4” LED LCD Panel
Built-in 100W or 150W Flex-ATX power supply for AC 110V/220V input
NEXCOM USB card containing ICEK 668-T6 Design-in documentation
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
xiii
Qty
1
1
1
1
1
ICEK 668-T6 Starter Kit User Manual
Preface
Ordering Information
The following information below provides ordering information for ICEK 668-T6.
ICES 668-3610ME (P/N: 10K00066806X0)
COM Express Type 6 Basic module, 3rd generation Intel® Core™ i5-3610ME processor (2x 2.7GHz, 3M Cache, 35W) paired with mobile Intel® QM77 express
chipset, ECC DDR3/2x SO-DIMMs
ICES 668-3615QE (P/N: 10K00066805X0)
COM Express Type 6 Basic module, 3rd generation Intel® Core™ i7-3615QE processor (4x 2.3GHz, 6M Cache, 45W) paired with mobile Intel® QM77 express
chipset, ECC DDR3/2x SO-DIMMs
ICES 668-3555LE (P/N: 10K00066804X0)
COM Express Type 6 Basic module, 3rd generation Intel® Core™ i7-3555LE processor (2x 2.5GHz, 4M Cache, 25W) paired with mobile Intel® QM77 express
chipset, ECC DDR3/2x SO-DIMMs
ICES 668-3517UE (P/N: 10K00066803X0)
COM Express Type 6 Basic module, 3rd generation Intel® Core™ i7-3517UE processor (2x 1.7GHz, 4M Cache, 17W), paired with mobile Intel® QM77 express
chipset, ECC DDR3/2x SO-DIMMs
ICES 668-3217UE (P/N: 10K00066801X0)
COM Express Type 6 Basic module, 3rd generation Intel® Core™ i3-3217UE processor (2x 1.6Ghz, 3M Cache, 17W), paired with mobile Intel® QM77 express
chipset, ECC DDR3/2x SO-DIMMs
ICEK 668-T6 (Subject to project registration)
ICES 668-3610ME with mobile Intel® QM77 express chipset, built-in min. ECC-DDR3/ 4GB system memory onboard installed on ICEB 8060 type-6 carrier MB/
ATX, pre-installed trial version of Microsoft Windows® 7 onto bootable 8GB CFast SSD for 10.4” LCD panel and Flex ATX PSU AC 110/220V input
ICEB 8060 (P/N:10KB0806000X0) RoHS Compliant
COM Express Type 6, COM.0 Rev. 2.0 Evaluation CRB, 3DDI/ VGA/ LVDS/ 4USB3.0/ 8USB2.0/ 6COM/ 2GbE/ 5.1 HD, SPDIF/ 2SATA3.0/ mSATA/ CFast/ PCIex16/
PCIex4/ PCIex1/ mPCIe, ATX input
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
xiv
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
Chapter 1: Product Introduction
Overview - ICES 668
Key Features
▪▪ PICMG COM.0 Rev. 2.0 Type 6 Basic module (95mm x 125mm)
▪▪ Support 3rd generation Intel® Core™ i7/ i5/ i3 processor family with ECC
▪▪ Mobile Intel® QM77 Express Chipset
▪▪ Dual DDR3 1333/1600MHz SO-DIMM sockets for up to 16GB ECC
memory
▪▪ 3x independent displays: VGA, 18/24-bit LVDS, DVI, HDMI, DisplayPort
▪▪ 1x PCIe x16, 7x PCIe x1, 4x USB 3.0, 8x USB 2.0, 2x SATA 3.0, 2x SATA
2.0 and GbE
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
1
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
Hardware Specifications
On-board LAN
▪▪ Intel® 82579LM Gigabit Ethernet, support iAMT 8.0
▪▪ Support PXE boot from LAN, wake on LAN function
▪▪ Signals down to I/O board
CPU Support
▪▪ Support Intel® BGA 1023, 3rd generation Intel® Core™ processor
–– Intel® Core™ i7 3615QE (4C/ 6M cache/ 2.3GHz/ Max. TDP 45W)
–– Intel® Core™ i7 3555LE (2C/ 4M cache/ 2.5GHz/ Max. TDP 25W)
–– Intel® Core™ i7 3517UE (2C/ 4M cache/ 1.7GHz/ Max. TDP 17W)
–– Intel® Core™ i3 3217UE (2C/ 3M cache/ 1.6GHz/ Max. TDP 17W)
–– Intel® Core™ i5 3610ME (2C/ 3M cache/ 2.7GHz/ Max. TDP 35W)
COM Express Connector
▪▪ AB
VGA/ LVDS/ 8x USB 2.0 / 2x Serial Port / HD Audio/ 4x SATA/ GbE/ GPIO/
LPC bus, 1x PCIe X4/ 3x PCIe X1/ SMBus (I2C)/ SPI BIOS /SPK out
▪▪ CD
PCIe x16/ 3x DDI/ 4x USB 3.0
Main Memory
▪▪ Dual DDR3/ SO-DIMMs, support 1333/1600MHz ECC system memory
Power Requirements
up to 16GB
▪▪ +12V, +5VSB, +3.3V RTC power
Platform Control Hub
Dimensions
▪▪ Intel® QM77 PCH chipset
▪▪ 95mm (W) x 125mm (L)
BIOS
Environment
▪▪ AMI System UEFI BIOS
▪▪ Plug and play support
▪▪ Advanced power management and advanced configuration & power
interface support
▪▪ Board level operating temperatures: 0°C to 60°C
▪▪ Storage temperatures: -20°C to 80°C
▪▪ Relative humidity:
10% to 90% (operating, non-condensing)
5% to 95% (non-operating, non-condensing)
Display
▪▪
▪▪
▪▪
▪▪
Intel® HD graphics with DX11 support up to triple independent displays
One PCI Express x16 Lane down to the carried board
Supports VGA and single/dual channel s 18/24 bit LVDS interface
3x DDI (Digital Display Interface) supports HDMI/ DVI, DisplayPort and
SVDO interfaces
Certifications
▪▪ Meet CE
▪▪ FCC Class A
Audio
▪▪ HD audio interface
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
2
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
Knowing Your ICES 668
CPU FAN
Support ECC DDR3/ SO-DIMM
Only up to 16GB (2x 8GB)
DDR3_SEL
PCIe DIP
switch
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
3
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
Overview - ICEB 8060
Key Features
▪▪ COM Express COM.0, Rev 2.0 Evaluation CRB, ATX form-factor
▪▪ Support Type 6 pin-out, COMe Extended/ Basic/ Compact Module
▪▪ Display: 3x DDI (2DP/HDMI), VGA & dual channels 18/24-bit LVDS
▪▪ 4x USB 3.0/ 2x SATA3.0, PCIe Gen 3.0, Bootable CFast or mini-SATA
▪▪ PCIe x 16, DDI (PCIex16), PCIe x4, PCIe x1 and mini-PCIe for Wi-Fi
▪▪ VGA/RS232/422/485/ 5COM, Dual GbE/12USB/ 5.1, S/PDIF
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
4
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
Hardware Specifications
I/O Interface
▪▪ Serial COM: 6 ports
–– 1x edge DB9 connector to supportRS232/ 422/ 485 (+5/ +12V by Ring)
–– 5x internal box-header 2.0 pitch to support RS232
▪▪ USB: 12 ports 4xUSB 3.0 and 8x USB2.0 ports
–– 4x USB 3.0/ 4x USB 2.0 ports by stack Type A on edge
–– 3x USB 2.0 by 4-pins JST2.0mm JST connector,
–– 1x internal USB 2.0 to mini-PCIe slot for external wi-fi module
▪▪ SATA: 4 ports
–– 2x SATA 3.0 ports
–– 1x mini-SATA by mini-PCIe slot for half-/ full size mini-SATA/ SSD
–– 1x CFAST slot for CFAST/ SATA 2.0
▪▪ PS/2: internal 2x 4-pins header for Keyboard/Mouse
▪▪ GPIO ports: 2x + 8x pins GPIO signals from COMe (default 5V TTL/ option
3.3V)
Form Factor
▪▪ ATX Carrier MB, dimension: 305mm x 244mm [ 12” x 9.6”]
▪▪ COM Express Evaluation CRB: PICMB COM Express board-to-board
interconnectors, type 6 pin-put, female, 8mm stack-up height, COM.0
Rev. 2.0
NEXCOM Computer-on-Modules Support List
▪▪ Basic Size (125x 95mm) : ICES 668
Expansion
▪▪
▪▪
▪▪
▪▪
1x PCIe x16 slot, support PEG interfaces
1x DDI (SDVO/ HDMI/ DP by orange color PCIe x16 slot)
1x PCIe x4 slot, optional 4x PCIe x1 signals
1x PCIe x1 slot and 1x mini-PCIe slot for Wi-Fi with SIM tray
Network
▪▪
▪▪
▪▪
▪▪
▪▪
Graphic Interfaces
▪▪
▪▪
▪▪
▪▪
Graphic Chip: from Type 6 pin-out, COM Express module
CRT: support analog VGA with DB15 connector on the I/O edge
LVDS: dual channels 18/24-bit LVDS connector (dual DF-13-20P)
DDI (in PCIe x16): optional EBK-A2HDMI riser card for HDMI or DP
Audio
Super I/O
▪▪
▪▪
▪▪
▪▪
▪▪ nuvoton, NCT6106D
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
ETH0: LAN port Connected from COMe CPU module (ICES668)
ETH0: Support 1x RJ45/ GbE LAN port on the edge I/O
ETH1: Support 2nd. RJ45/ GbE LAN port by Intel 82574L on the edge I/O
ETH0 and ETH1 support Boot from LAN (PXE)
ETH0 and ETH1 support Wake-on-LAN (when +5Vsb power available)
5
HD Audio AL886 with 5.1 channels
Support external S/PDIF interface
Support internal pin-header for L/R speaker-out 2W/ 4 Ohm
Onboard buzzer
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
EEPROM
▪▪ 1x 2K EEPROM to record PCI Express Lane configuration
▪▪ ATMEL AT24C32 (or C02) and address 0x57 or (0xAE)
Watchdog Timer
▪▪ Watchdog timeout can be programmed by Software from 1 second
to 255 seconds and from 1 minute to 255 minutes (tolerance 15%
temperature 25°C)
On-board RTC
▪▪ On-chip RTC with battery BR2032
Power Input
▪▪ Standard ATX 24 pins and AUX 4-pins with 12V
Dimensions
▪▪ ATX form factor, 305x 244mm (Lx W, 12”x9.6”)
Environment
▪▪ Operating temperatures: -20°C to 60°C
▪▪ Storage temperature: -40°C to 85°C
▪▪ Relative humidity: Operating 10% to 90%, non-condensing
Certifications
▪▪ CE approval
▪▪ FCC Class A
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
6
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
Knowing Your ICEB 8060
PCIe x1
PCIe x4
HD 5.1
Audio, S/PDIF
DDI
(Port B/ DDI#1)
CFast1
GbE LAN/2USB
DisplayPort
VGA & COM2
mSATA/SSD
Battery RTC
mPCIe/ Wi-Fi
Option SIM
PEG x16 Slot
Port 80
LVDS
4P ATX
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
ATX Power
Battery charger
7
COM Port box header
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
Block Diagram
ICES 668
DDR3 Channel A
DDR3 CH A
DDR3 1066/1333 MHz ECC DIMM0
GFXCORE
DDR3 CH B
DDR3 Channel B
DDR3 1066/1333 MHz ECC DIMM1
31 x 24 mm (BGA1023)
PCIex16
Vcore
IMVP 7
CORE POWER
Ivy Bridge
FDI
PCIex16 BUS
DMI
Flexible
DMI(X4)
Display
LPC BUS
PORT D
USB3.0
DISPLAY PORT B
USB3.0 BUS
PORT:0-3
PCIE*1 BUS
PORT:7
25 x 25 mm
FCBGA(Mobile only)
PCIE BUS
USB (12)
USB2.0 BUS
DISPLAY PORT C
LPC
PORT:0-7
LVDS
QM77
DISPLAY
LVDS BUS
PORT C
PORT:A.B
Panther Point
DISPLAY PORT D
DISPLAY
SATA BUS
DMI
PORT B
PORT:0-3
FDI
DISPLAY
HDA
VGA
HDA BUS
SATA
VGA BUS
COM Express connector C and D
COM Express connector A and B
Interface
PCIE BUS
SMBUS
SPI
LPC TO COM
SERIAL PORT:1.2
F81216
PCI-E*1 BUS PORT:1,2,3,4,5,6
TYPE 6
BIOS
HWM
INTEL WG82579LM
MDI BUS
GbE PHY
NCT7802Y
PCI-E*1 BUS PORT:8
iAMT
TYPE 6
SPI ROM
SMBUS
SPI BUS
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
8
ICEK 668-T6 Starter Kit User Manual
Chapter 1: Product Introduction
ICEB 8060
SATA X 2
SATA x2 BUS
SATA x1 BUS
Connector
SATA x1 BUS
CFAST X1
Connector
USB 2.0 X 2
Pin Header
USB2.0 BUS
USB 2.0 X 4
(rear IO)
USB2.0 BUS
USB 2.0 X 1
(box header)
USB2.0 BUS
PCI-E x4
SLOT X1
PCI-E x4 BUS
PCI-E x1
SLOT X1
PCI-E x1 BUS
VGA
DB-15 rear IO Connector
LVDS Channel A
LVDS A
(18/24 bit)
Connector
SPEAKER
LVDS Channel B
LVDS B
(18/24 bit)
Connector
HD Audio interface
Audio Codec chip
(ALC886)
Audio Rear IO Connector
Line IN / Line OUT / MIC IN
CEN OUT / SIDE OUT / SPDIF
PIN
HEARD
AMP
Line OUT
COM Express connector C and D
mSATA X1
R/G/B
COM Express connector A and B
Connector
DDI1
DDI2
DDI3
USB3.0 BUS
PCI-E x1 BUS
PCI-E x1 BUS
DDI1 (PEGx16 SLOT)
DDI2 (Display port rear IO connector)
DDI3 (Display port rear IO connector)
USB3.0 X 4
Rear IO connector
PCIEX1 (LAN2)
Giga LAN
Rear IO connector
PCI-E x1
SLOT X1
x16 PEG BUS
PEG x16
SLOT X1
WIFI/3G
MiniPCIE X1
USB 2.0 X 1
SLOT
PCI-E x1 BUS
USB2.0 BUS
I2C BUS
EEPROM
KB/MS
Pin Header
COM 2
RS232/422/485
rear IO Connector
COM 1,3~6
RS232
box header X5
GPI *4
GPO *4
GPIO BUS
TTL LEVLE
SUPER I/O
LPC BUS
IT8783E/AX-L
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
TYPE 6
Giga LAN
RJ45
Rear IO Connector
9
TYPE 6
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Chapter 2: Jumpers and Connectors
dry environments. A grounding strap is warranted whenever danger of
static electricity exists.
This chapter describes how to set the jumpers and connectors on the
ICES 668 and ICEB 8060 motherboard.
Before You Begin
Precautions
▪▪ Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
Computer components and electronic circuit boards can be damaged by
discharges of static electricity. Working on computers that are still connected
to a power supply can be extremely dangerous.
▪▪ Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
– A Philips screwdriver
– A flat-tipped screwdriver
– A set of jewelers screwdrivers
– A grounding strap
– An anti-static pad
Follow the guidelines below to avoid damage to your computer or yourself:
▪▪ Always disconnect the unit from the power outlet whenever you are
working inside the case.
▪▪ If possible, wear a grounded wrist strap when you are working inside the
computer case. Alternatively, discharge any static electricity by touching
the bare metal chassis of the unit case, or the bare metal body of any
other grounded appliance.
▪▪ Using your fingers can disconnect most of the connections. It is
recommended that you do not use needle-nosed pliers to disconnect
connections as these can damage the soft metal or plastic parts of the
connectors.
▪▪ Hold electronic circuit boards by the edges only. Do not touch the
components on the board unless it is necessary to do so. Don’t flex or
stress the circuit board.
▪▪ Before working on internal components, make sure that the power is off.
Ground yourself before touching any internal components, by touching
a metal object. Static electricity can damage many of the electronic
components. Humid environments tend to have less static electricity than
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
▪▪ Leave all components inside the static-proof packaging that they shipped
with until they are ready for installation.
▪▪ Use correct screws and do not over tighten screws.
10
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Jumper Settings
A jumper is the simplest kind of electric switch. It consists of two metal
pins and a cap. When setting the jumpers, ensure that the jumper caps are
placed on the correct pins. When the jumper cap is placed on both pins, the
jumper is short. If you remove the jumper cap, or place the jumper cap on
just one pin, the jumper is open.
Refer to the illustrations below for examples of what the 2-pin and 3-pin
jumpers look like when they are short (on) and open (off).
Two-Pin Jumpers: Open (Left) and Short (Right)
Three-Pin Jumpers: Pins 1 and 2 are Short
1
2
3
1
2
3
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
11
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Locations of the Jumpers and Connectors for ICES 668
The figure below shows the location of the jumpers and connectors for ICES 668.
Support ECC DDR3/ SO-DIMM Only
FAN1
SW2
Support ECC DDR3/ SO-DIMM Only up to 16GB (2x 8GB)
SW1
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
12
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Connector Pin Definitions
Internal Connectors
Connector type: 2x4 4-pin DIP switch
Connector location: SW2
Connector type: 2x4 4-pin DIP switch
Connector location: SW1
Pin
1
3
1
2
1
2
O
N
PCIe DIP Switch
O
N
DDR3_SEL and F82126 ADDRESS SEL DIP SW SIGNAL
Definition
DDR3_SEL
GND
Pin
2
4
Definition
SA_COM3RTS#
GND
Pin
1
3
SW2.1
Definition
CFG5
GND
PCI Express Bifurcation
Pin
2
4
(CFG6) (CFG5)
OFF
SUPPORT DDR3
CFG6
CFG5
ON
SUPPORT DDR3L
0
0
1 x 8, 2 x 4 PCI Express
0
1
reserved
SW2.2
OFF
F82126 ADDRESS IS 4E
1
0
2 x8 PCI Express
ON
F82126 ADDRESS IS 2E
1
1
1 x16 PCI Express
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
13
Definition
CFG6
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
CPU Fan Connector
Connector type: 1x3 3-pin header
Connector location: FAN1
1
3
Pin
1
3
Definition
GND
VCC5_S
Pin
2
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
VCC5_S
14
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
High Speed Board-to-Board Connector: Row A and B, Row C and D
Connector location: J2
Com Express A&B Connector
Com Express C&D Connector
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
Definition
GND(FIXED)
GBE0_MDI3GBE0_MDI3+
GBE0_LINK100#
GBE0_LINK1000#
GBE0_MDI2GBE0_MDI2+
GBE0_LINK#
GBE0_MDI1GBE0_MDI1+
GND(FIXED)
GBE0_MDI0GBE0_MDI0+
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND(FIXED)
GBE0_ACT#
LPC_FRAME#
LPC_AD0
LPC_AD1
LPC_AD2
LPC_AD3
LPC_DRQ0#
LPC_DRQ1#
LPC_CLK
GND(FIXED)
PWRBTN#
SMB_CK
Pin
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
15
Definition
GND(FIXED)
GND
USB_SSRX0USB_SSRX0+
GND
USB_SSRX1USB_SSRX1+
GND
USB_SSRX2USB_SSRX2+
GND(FIXED)
USB_SSRX3USB_SSRX3+
Pin
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
Definition
GND(FIXED)
GND
USB_SSTX0USB_SSTX0+
GND
USB_SSTX1USB_SSTX1+
GND
USB_SSTX2USB_SSTX2+
GND(FIXED)
USB_SSTX3USB_SSTX3+
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
Definition
GBE0_CTREF
SUS_S3#
SATA0_TX+
SATA0_TXSUS_S4#
SATA0_RX+
SATA0_RXGND(FIXED)
SATA2_TX+
SATA2_TXSUS_S5#
SATA2_RX+
SATA2_RXBATLOW#
(S)ATA_ACT#
AC/HDA_SYNC
AC/HDA_RST#
GND(FIXED)
AC/HDA_BITCLK
AC/HDA_SDOUT
BIOS_DIS0#
THRMTRIP#
USB6USB6+
USB_6_7_OC#
USB4USB4+
GND(FIXED)
Pin
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
SMB_DAT
SMB_ALERT#
SATA1_TX+
SATA1_TXSUS_STAT#
SATA1_RX+
SATA1_RXGND(FIXED)
SATA3_TX+
SATA3_TXPWR_OK
SATA3_RX+
SATA3_RXWDT
AC/HDA_SDIN2
AC/HDA_SDIN1
AC/HDA_SDIN0
GND(FIXED)
SPKR
I2C_CK
I2C_DAT
THRM#
USB7USB7+
USB_4_5_OC#
USB5USB5+
GND(FIXED)
Pin
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C36
C37
C38
C39
C40
C41
16
Definition
GND
DDI1_PAIR6+
DDI1_PAIR6RSVD
RSVD
PCIE_RX6+
PCIE_RX6GND(FIXED)
PCIE_RX7+
PCIE_RX7DDI1_HPD
DDI1_PAIR4+
DDI1_PAIR4RSVD
RSVD
DDI1_PAIR5+
DDI1_PAIR5GND(FIXED)
DDI2_CTRL_CLK_AUX+
DDI2_CTRL_DATA_AUXDDI2_DDC_AUX_SEL
RSVD
DDI3_CTRL_CLK_AUX+
DDI3_CTRL_DATA_AUXDDI3_DDC_AUX_SEL
DDI3_PAIR0+
DDI3_PAIR0GND(FIXED)
Pin
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
D32
D33
D34
D35
D36
D37
D38
D39
D40
D41
Definition
GND
DDI11_CTRL_CLK_AUX+
DDI11_CTRL_DATA_AUXRSVD
RSVD
PCIE_TX6+
PCIE_TX6GND(FIXED)
PCIE_TX7+
PCIE_TX7RSVD
RSVD
DDI1_PAIR0+
DDI1_PAIR0RSVD
DDI1_PAIR1+
DDI1_PAIR1GND(FIXED)
DDI1_PAIR2+
DDI1_PAIR2DDI1_DDC_AUX_SEL
RSVD
DDI1_PAIR3+
DDI1_PAIR3RSVD
DDI2_PAIR0+
DDI2_PAIR0GND(FIXED)
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
A63
A64
A65
A66
A67
A68
A69
Definition
USB2USB2+
USB_2_3_OC#
USB0USB0+
VCC_RTC
EXCD0_PERST#
EXCD0_CPPE#
LPC_SERIRQ
GND(FIXED)
PCIE_TX5+
PCIE_TX5GPI0
PCIE_TX4+
PCIE_TX4GND
PCIE_TX3+
PCIE_TX3GND(FIXED)
PCIE_TX2+
PCIE_TX2GPI1
PCIE_TX1+
PCIE_TX1GND
GPI2
PCIE_TX0+
PCIE_TX0-
Pin
B42
B43
B44
B45
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
B63
B64
B65
B66
B67
B68
B69
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
USB3USB3+
USB_0_1_OC#
USB1USB1+
EXCD1_PERST#
EXCD1_CPPE#
SYS_RESET#
CB_RESET#
GND(FIXED)
PCIE_RX5+
PCIE_RX5GPO1
PCIE_RX4+
PCIE_RX4GPO2
PCIE_RX3+
PCIE_RX3GND(FIXED)
PCIE_RX2+
PCIE_RX2GPO3
PCIE_RX1+
PCIE_RX1WAKE0#
WAKE1#
PCIE_RX0+
PCIE_RX0-
Pin
C42
C43
C44
C45
C46
C47
C48
C49
C50
C51
C52
C53
C54
C55
C56
C57
C58
C59
C60
C61
C62
C63
C64
C65
C66
C67
C68
C69
17
Definition
DDI3_PAIR1+
DDI3_PAIR1DDI3_HPD
RSVD
DDI3_PAIR2+
DDI3_PAIR2RSVD
DDI3_PAIR3+
DDI3_PAIR3GND(FIXED)
PEG_RX0+
PEG_RX0TYPE0#
PEG_RX1+
PEG_RX1TYPE1#
PEG_RX2+
PEG_RX2GND(FIXED)
PEG_RX3+
PEG_RX3RSVD
RSVD
PEG_RX4+
PEG_RX4RSVD
PEG_RX5+
PEG_RX5-
Pin
D42
D43
D44
D45
D46
D47
D48
D49
D50
D51
D52
D53
D54
D55
D56
D57
D58
D59
D60
D61
D62
D63
D64
D65
D66
D67
D68
D69
Definition
DDI2_PAIR1+
DDI2_PAIR1DDI2_HPD
RSVD
DDI2_PAIR2+
DDI2_PAIR2RSVD
DDI2_PAIR3+
DDI2_PAIR3GND(FIXED)
PEG_TX0+
PEG_TX0PEG_LANE_RV#
PEG_TX1+
PEG_TX1TYPE2#
PEG_TX2+
PEG_TX2GND(FIXED)
PEG_TX3+
PEG_TX3RSVD
RSVD
PEG_TX4+
PEG_TX4GND
PEG_TX5+
PEG_TX5-
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A70
A71
A72
A73
A74
A75
A76
A77
A78
A79
A80
A81
A82
A83
A84
A85
A86
A87
A88
A89
A90
A91
A92
A93
A94
A95
A96
A97
Definition
GND(FIXED)
LVDS_A0+
LVDS_A0LVDS_A1+
LVDS_A1LVDS_A2+
LVDS_A2LVDS_VDD_EN
LVDS_A3+
LVDS_A3GND(FIXED)
LVDS_A_CK+
LVDS_A_CKLVDS_I2C_CK
LVDS_I2C_DAT
GPI3
RSVD(KBD_RST#)
RSVD(A20GATE)
PCIE_CLK_REF+
PCIE_CLK_REFGND(FIXED)
SPI_POWER
SPI_MISO
GPO0
SPI_CLK
SPI_MOSI
TPM_PP
TYPE10#
Pin
B70
B71
B72
B73
B74
B75
B76
B77
B78
B79
B80
B81
B82
B83
B84
B85
B86
B87
B88
B89
B90
B91
B92
B93
B94
B95
B96
B97
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND(FIXED)
LVDS_B0+
LVDS_B0LVDS_B1+
LVDS_B1LVDS_B2+
LVDS_B2LVDS_B3+
LVDS_B3LVDS_BKLT_EN
GND(FIXED)
LVDS_B_CK+
LVDS_B_CKLVDS_BKLT_CTRL
VCC_5V_SBY
VCC_5V_SBY
VCC_5V_SBY
VCC_5V_SBY
BIOS_DIS1#
VGA_RED
GND(FIXED)
VGA_GRN
VGA_BLU
VGA_HSYNC
VGA_VSYNC
VGA_I2C_CK
VGA_I2C_DAT
SPI_CS#
Pin
C70
C71
C72
C73
C74
C75
C76
C77
C78
C79
C80
C81
C82
C83
C84
C85
C86
C87
C88
C89
C90
C91
C92
C93
C94
C95
C96
C97
18
Definition
GND(FIXED)
PEG_RX6+
PEG_RX6SDVO_DATA
PEG_RX7+
PEG_RX7GND
RSVD
PEG_RX8+
PEG_RX8GND(FIXED)
PEG_RX9+
PEG_RX9RSVD
GND
PEG_RX10+
PEG_RX10GND
PEG_RX11+
PEG_RX11GND(FIXED)
PEG_RX12+
PEG_RX12GND
PEG_RX13+
PEG_RX13GND
RSVD
Pin
D70
D71
D72
D73
D74
D75
D76
D77
D78
D79
D80
D81
D82
D83
D84
D85
D86
D87
D88
D89
D90
D91
D92
D93
D94
D95
D96
D97
Definition
GND(FIXED)
PEG_TX6+
PEG_TX6GND
PEG_TX7+
PEG_TX7GND
RSVD
PEG_TX8+
PEG_TX8GND(FIXED)
PEG_TX9+
PEG_TX9RSVD
GND
PEG_TX10+
PEG_TX10GND
PEG_TX11+
PEG_TX11GND(FIXED)
PEG_TX12+
PEG_TX12GND
PEG_TX13+
PEG_TX13GND
RSVD
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A98
A99
A100
A101
A102
A103
A104
A105
A106
A107
A108
A109
A110
Definition
SER0_TX
SER0_RX
GND(FIXED)
SER1_TX
SER1_RX
LID#
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
GND(FIXED)
Pin
B98
B99
B100
B101
B102
B103
B104
B105
B106
B107
B108
B109
B110
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
RSVD
RSVD
GND(FIXED)
FAN_PWMOUT
FAN_TACHIN
SLEEP#
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
GND(FIXED)
Pin
C98
C99
C100
C101
C102
C103
C104
C105
C106
C107
C108
C109
C110
19
Definition
PEG_RX14+
PEG_RX14GND(FIXED)
PEG_RX15+
PEG_RX15GND
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
GND(FIXED)
Pin
D98
D99
D100
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
Definition
PEG_TX14+
PEG_TX14GND(FIXED)
PEG_TX15+
PEG_TX15GND
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
GND(FIXED)
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Locations of the Jumpers and Connectors for ICEB 8060
The figure below shows the location of the jumpers and connectors for ICEB 8060.
JUSB1
COM1 COM4
COM3 COM5
JP14 JP15
JP16
COM6
JP4
CN15 JP18
JP17
J3
JP19
JUSB2
ATX1
ATX12
CFAN1
JP6
LVDS1
JP13
JCCFL1 LVDS2
SW1
J5
SIM
J6
MSATA1
JP3 MPCIE1
J1
J4
JP12
SW3
SW2
JP10
JP11
SATA2
CN9
DDI2
USB2
JPCIE1 JDDI1 JPCIE2 JPCIE3 JPCIE4
SATA1
DDI3
CFAST1
JP1
USB1
AUDIO1
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
20
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Jumpers
3.5G Module
LVDS Power Select (3.3V/5V)
Connector type: 1x3 3-pin header, 2.0mm pitch
Connector location: JP3
Connector type: 1x3 3-pin header, 2.54mm pitch
Connector location: JP6
1
3
Pin
1-2 On
2-3 On
1
Settings
Wi-Fi
3.5G
Pin
1-2 On
2-3 On
2-3 On: default
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
3
Settings
+3.3V
+5V
2-3 On: default
21
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Termal Select
GPIO Power Select
Connector type: 1x3 3-pin header, 2.54mm pitch
Connector location: JP11
Connector type: 1x3 3-pin header, 2.54mm pitch
Connector location: JP15
1
3
Pin
1-2 On
2-3 On
1
Settings
Enable
Disable
Pin
1-2 On
2-3 On
2-3 On: default
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
3
Settings
+5V
+3.3V
2-3 On: default
22
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Power Mode Select
RTC Clear
Connector type: 1x3 3-pin header, 2.54mm pitch
Connector location: JP19
Connector type: 1x3 3-pin header, 2.54mm pitch
Connector location: J4
1
1
3
Pin
1-2 On
2-3 On
Settings
ATX
AT
Pin
1-2 On
2-3 On
1-2 On: default
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
3
Settings
Normal
Clear CMOS
1-2 On: default
23
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Fintek TX/RX Pin Header
Connector type: 1x3 3-pin header, 2.54mm pitch
Connector location: J5 and J6
1
3
J6
Pin
1
2
3
Settings
SER0TX1
SER0RX1
GND
Pin
1
2
3
Settings
SER1TX1
SER1RX1
GND
J5
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
24
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
DIP Switch Settings
Connector type: 2x2 4-pin DIP switch
Connector location: SW1
Connector type: 2x4 8-pin DIP switch
Connector location: SW2
1
2
1
2
3
4
O
N
RS232/ RS422/ RS485 Mode Select
O
N
Close to U4
Pin
1-2 Off
1-2 On
Settings
Enable
Disable
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
25
SW2
ON:0 OFF:1
SW2.1
MODE0
SW2.2
MODE1
SW2.3
MODE2
SW2.4
DIR
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
BIOS Select
1
2
O
N
Connector type: 2x2 4-pin DIP switch
Connector location: SW3
SW3
ON:0 OFF:1
SW3.1
BIOS_DIS0#
SW3.2
BIOS_DIS1#
BIOS_DIS1#
BIOS_DIS0#
Carrier
SPI_CS#
SPI
Descriptor
BIOS Entry
1
1
High
Module
SPI0/SPI1
1
0
High
Module
Carrier FWH
0
1
SPI0
Carrier
SPI0/SPI1
0
0
SPI1
Module
SPI0/SPI1
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
26
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Connector Pin Definitions
External Connectors
VGA and COM2 Ports
Connector type: DB-15 port, 15-pin D-Sub (VGA)
DB-9 port, 9-pin D-Sub
Connector location: CN9
VGA
Pin
1
3
5
7
9
11
13
15
MH1
COM2
Definition
VGA_R
VGA_B
GND
GND
+5V
NC
VGA_HSYNC
VGA_CLK
RGND
Pin
2
4
6
8
10
12
14
MH1
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND
NC
VGADET
GND
GND
VGA_DAT
VGA_VSYNC
RGND
Pin
16
18
20
22
24
MH4
27
Definition
COM_DCD#2
COM_TXD2
GND
COM_RTS#2
COM_RI#2_con
RGND
Pin
17
19
21
23
MH3
Definition
COM_RXD2
COM_DTR#2
COM_DSR#2
COM_CTS#2
RGND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
LAN and USB Ports
Connector type: RJ45 port with LEDs and dual USB 3.0/2.0 ports, Type A
Connector location: USB1 and USB2
ACT
LINK
LAN1
USB1
Pin
1
3
5
7
9
11
13
15
17
MH1
MH3
Definition
+5V_USB
USB_0P_C
USB3_RX0_N_C
GND
USB3_TX0_P_C
USB_1N_C
GND
USB3_RX1_P_C
USB3_TX1_N_C
RGND
RGND
Pin
2
4
6
8
10
12
14
16
18
MH2
MH4
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
19
21
23
25
27
29
31
MH5
MH7
Definition
USB_0N_C
GND
USB3_RX0_P_C
USB3_TX0_N_C
+5V_USB
USB_1P_C
USB3_RX1_N_C
GND
USB3_TX1_P_C
RGND
RGND
28
Definition
V25_LA1
LAN1_MDI0N
LAN1_MDI1N
LAN1_MDI2N
LAN1_MDI3N
+3.3VSBY
LAN1_LED_LINK100#
RGND
RGND
Pin
20
22
24
26
28
30
32
MH6
MH8
Definition
LAN1_MDI0P
LAN1_MDI1P
LAN1_MDI2P
LAN1_MDI3P
GND
LAN1_LED_ACT#
LAN1_LED_LINK1G#O
RGND
RGND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
DisplayPort
USB2
Pin
1
3
5
7
9
11
13
15
17
MH1
MH3
Definition
+5V_USB
USB_2P_C
USB3_RX2_N_C
GND
USB3_TX2_P_C
USB_3N_C
GND
USB3_RX3_P_C
USB3_TX3_N_C
RGND
RGND
Pin
2
4
6
8
10
12
14
16
18
MH2
MH4
Definition
USB_2N_C
GND
USB3_RX2_P_C
USB3_TX2_N_C
+5V_USB
USB_3P_C
USB3_RX3_N_C
GND
USB3_TX3_P_C
RGND
RGND
Definition
V25_LA1
LAN2_MDI0N
LAN2_MDI1N
LAN1_MDI2N
LAN1_MDI3N
+3.3VSBY
LAN2_LED_LINK100#
RGND
RGND
Pin
20
22
24
26
28
30
32
MH6
MH8
Definition
LAN2_MDI0P
LAN2_MDI1P
LAN2_MDI2P
LAN2_MDI3P
GND
LAN2_LED_ACT#
LAN2_LED_LINK1G#O
RGND
RGND
Connector type: DisplayPort
Connector location: DDI2 and DDI3
DDI2
Pin
1
3
5
7
9
11
13
15
17
19
MH1
MH3
LAN2
Pin
19
21
23
25
27
29
31
MH5
MH7
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
29
Definition
DP2_CN_LANE0P
DP2_CN_LANE0N
GND
DP2_CN_LANE2P
DP2_CN_LANE2N
GND
DP2_CONFIG1
DDI2_CTRLCLK_AUXP
DDI3_CTRLDATA_AUXN
GND
RGND
RGND
Pin
2
4
6
8
10
12
14
16
18
20
MH2
MH4
Definition
GND
DP2_CN_LANE1P
DP2_CN_LANE1N
GND
DP2_CN_LANE3P
DP2_CN_LANE3N
DP2_CONFIG2
GND
DP2_HPD_C
+3.3V
RGND
RGND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Audio Connectors
DDI3
Pin
1
3
5
7
9
11
13
15
17
19
MH1
MH3
Definition
DP3_CN_LANE0P
DP3_CN_LANE0N
GND
DP3_CN_LANE2P
DP3_CN_LANE2N
GND
DP3_CONFIG1
DDI3_CTRLCLK_AUXP
DDI3_CTRLDATA_AUXN
GND
RGND
RGND
Pin
2
4
6
8
10
12
14
16
18
20
MH2
MH4
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Connector type: 5x 3.5mm TRS, 1x S/PDIF
Connector location: AUDIO1
Definition
GND
DP3_CN_LANE1P
DP3_CN_LANE1N
GND
DP3_CN_LANE3P
DP3_CN_LANE3N
DP3_CONFIG2
GND
DP3_HPD_C
+3.3V
RGND
RGND
Rear Surround
Center Subwoofer
S/PDIF
Pin
1
3
5
23
25
33
35
42
44
52
54
A
C
MH2
MH4
30
Line-in
Line-out
Mic-in
Definition
AGND
MIC_JD1
MIC_R
FRONT_JD
FRONT_R2
LINE1_JD
LINEIN_R
CEN_OUT
AGND
SIDE_L
AGND
SPDIFO
GND
RGND
RGND
Pin
2
4
22
24
32
34
41
43
45
53
55
B
MH1
MH3
Definition
MIC_L
AGND
FRONT_L2
AGND
LINEIN_L
AGND
AGND
CEN_JD
LEF_OUT
SIDESURR_JD
SIDE_R
+5V
RGND
RGND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Internal Connectors
HDD LED
Internal Speaker
Connector type: 1x2 2-pin header, 2.54mm pitch
Connector location: JP4
Connector type: 1x5 5-pin header, 2.0mm pitch
Connector location: JP1
1
Pin
1
2
2
1
Definition
+5V
GND
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
5
Pin
1
2
3
4
5
31
Definition
SPKR_L+
SPKR_LAGND
SPKR_R+
SPKR_R-
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
COM2 RS232 RI# Pin Power Select
GAL Download Port
Connector type: 1x5 5-pin header, 2.0mm pitch
Connector location: JP10
Connector type: 1x6 6-pin header, 2.54mm pitch
Connector location: JP12
1
1
5
Pin
1
2
3
4
5
Definition
SPKR_L+
SPKR_LAGND
SPKR_R+
SPKR_R-
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
6
Pin
1
3
5
32
Definition
+3.3V
TCK
TDI
Pin
2
4
6
Definition
GND
TDO
TMS
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
SPI
Disable EEPROM
Connector type: 2x4 8-pin header, 1.27mm pitch
Connector location: JP13
Connector type: 1x2 2-pin header, 2.54mm pitch
Connector location: JP14
2
8
1
7
Pin
1
3
5
7
1
Definition
SPI_CS
SPI_POWER
SPI_MOSI
SPI_POWER
Pin
2
4
6
8
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
SPI_MISO
GND
SPI_CLK
SPI_POWER
Pin
1
2
33
2
Definition
EEPROM_WP
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Keyboard and Mouse Pin Header
HW Reset Function
Connector type: 2x4 8-pin header, 2.54mm pitch
Connector location: JP16
Connector type: 1x2 2-pin header, 2.54mm pitch
Connector location: JP17
2
8
1
7
Pin
1
3
5
7
1
Definition
+5VSBY
KDAT_R
KCLK_R
KB_GND
Pin
2
4
6
8
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
+5VSBY
MDAT_R
MCLK_R
KB_GND
Pin
1
2
34
2
Definition
HW_R_RST#
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Power Button
GPIO
Connector type: 1x2 2-pin header, 2.54mm pitch
Connector location: JP18
Connector type: 2x5 10-pin header, 2.0mm pitch
Connector location: J3
1
Pin
1
2
2
Definition
PWRBTN
GND
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
2
10
1
9
Pin
1
3
5
7
9
35
Definition
GP_VCC
ICH_GPO0_OUT
ICH_GPO1_OUT
ICH_GPO2_OUT
ICH_GPO3_OUT
Pin
2
4
6
8
10
Definition
GND
ICH_GPI0_IN
ICH_GPI1_IN
ICH_GPI2_IN
ICH_GPI3_IN
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
USB Port 6 and 7
USB Port 5
Connector type: 2x4 8-pin header, 2.0mm pitch
Connector location: JUSB1
Connector type: 1x4 4-pin header, 2.0mm pitch
Connector location: JUSB2
2
8
1
7
Pin
1
3
5
7
4
Definition
+5V_USB
USB6N_C
USB6P_C
GND
Pin
2
4
6
8
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND
USB7P_C
USB7N_C
+5V_USB
1
Pin
1
2
3
4
36
Definition
+5V_USB
USB_5N
USB_5P
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
CCFL
LVDS Channel A
Connector type: 1x7 7-pin header, 2.0mm pitch
Connector location: JCCFL1
Connector type: 2x10 20-pin header, 1.25mm pitch
Connector location: LVDS1
7
1
2
1
Pin
1
3
5
7
9
Definition
+5V
ICH_GPO0_OUT
ICH_GPO1_OUT
ICH_GPO2_OUT
ICH_GPO3_OUT
Pin
2
4
6
8
10
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND
ICH_GPI0_IN
ICH_GPI1_IN
ICH_GPI2_IN
ICH_GPI3_IN
19
20
Pin
1
3
5
7
9
11
13
15
17
19
MH1
37
Definition
LVDS_DDC_CLK
Panel_VDD
LVDSA_DATA3
LVDSA_DATA#3
GND
LVDSA_CLK
LVDSA_CLK#
GND
LVDSA_DATA2
LVDSA_DATA#2
GND
Pin
2
4
6
8
10
12
14
16
18
20
MH2
Definition
LVDS_DDC_DATA
LVDSA_DATA0
LVDSA_DATA#0
Panel_VDD
LVDSA_DATA1
LVDSA_DATA#1
GND
Panel_backlight
Panel_backlight
GND
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
LVDS Channel B
COM1 Port Box Header
Connector type: 2x10 20-pin header, 1.25mm pitch
Connector location: LVDS2
Connector type: 2x5 10-pin header, 2.0mm pitch
Connector location: COM1
1
2
Pin
1
3
5
7
9
11
13
15
17
19
MH1
Definition
LVDS_DDC_CLK
Panel_VDD
LVDSB_DATA3
LVDSB_DATA#3
GND
LVDSB_CLK
LVDSB_CLK#
GND
LVDSB_DATA2
LVDSB_DATA#2
GND
10
9
2
1
19
20
Pin
2
4
6
8
10
12
14
16
18
20
MH2
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
LVDS_DDC_DATA
LVDSB_DATA0
LVDSB_DATA#0
Panel_VDD
LVDSB_DATA1
LVDSB_DATA#1
GND
Panel_backlight
Panel_backlight
GND
GND
Pin
1
3
5
7
9
38
Definition
COM_DCD#1
COM_TXD1
GND
COM_RTS#1
COM_RI#1
Pin
2
4
6
8
10
Definition
COM_RXD1
COM_DTR#1
COM_DSR#1
COM_CTS#1
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
COM3 Port Box Header
COM4 Port Box Header
Connector type: 2x5 10-pin header, 2.0mm pitch
Connector location: COM3
Connector type: 2x5 10-pin header, 2.0mm pitch
Connector location: COM4
10
9
2
1
Pin
1
3
5
7
9
Definition
COM_DCD#3
COM_TXD3
GND
COM_RTS#3
COM_RI#3
10
9
2
1
Pin
2
4
6
8
10
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
COM_RXD3
COM_DTR#3
COM_DSR#3
COM_CTS#3
GND
Pin
1
3
5
7
9
39
Definition
COM_DCD#4
COM_TXD4
GND
COM_RTS#4
COM_RI#4
Pin
2
4
6
8
10
Definition
COM_RXD4
COM_DTR#4
COM_DSR#4
COM_CTS#4
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
COM5 Port Box Header
COM6 Port Box Header
Connector type: 2x5 10-pin header, 2.0mm pitch
Connector location: COM5
Connector type: 2x5 10-pin header, 2.0mm pitch
Connector location: COM6
10
9
2
1
Pin
1
3
5
7
9
Definition
COM_DCD#5
COM_TXD5
GND
COM_RTS#5
COM_RI#5
10
9
2
1
Pin
2
4
6
8
10
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
COM_RXD5
COM_DTR#5
COM_DSR#5
COM_CTS#5
GND
Pin
1
3
5
7
9
40
Definition
COM_DCD#6
COM_TXD6
GND
COM_RTS#6
COM_RI#6
Pin
2
4
6
8
10
Definition
COM_RXD6
COM_DTR#6
COM_DSR#6
COM_CTS#6
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Battery Charger
Fan Connector
Connector type: 2x10 20-pin header, 2.0mm pitch
Connector location: CN15
Connector type: 1x4 4-pin header, 2.54mm pitch
Connector location: CFAN1
2
1
1
20
19
Pin
1
3
5
7
9
11
13
15
17
19
Definition
LPC_AD0
LPC_AD1
LPC_AD2
LPC_AD3
INT_SERIRQ
LPC_FRAME#
LPC_BAT_CLK
GND
GND
GND
Pin
2
4
6
8
10
12
14
16
18
20
Definition
SMBCLK_MAIN
SMBDATA_MAIN
SIO1_RSMRST#
PM_SLP_S3#
PM_SLP_S4#
PM_SLP_S5#
PM_PWRBTN#
PM_BATLOW#
CB_RESET#
PM_THRM#
4
Pin
1
3
Definition
GND
FANIN
Pin
2
4
Definition
+12V
FANOUT
* Preliminary box-header reserved for NEXCOM use only, above pins defined are subject to change without further notices. *
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
41
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
4-Pin Power Connector
ATX Power Connector
Connector type: 2x2 4-pin header
Connector location: ATX12
Connector type: 2x12 24-pin header, 4.2mm pitch
Connector location: ATX1
1
2
3
4
Pin
1
2
3
4
Definition
GND
GND
+12V
+12V
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
1
12
13
24
Pin
1
3
5
7
9
11
13
15
17
19
21
23
42
Definition
+3.3V
GND
GND
GND
+5VSBY
+12V
+3.3V
GND
GND
GND
+5V
+5V
Pin
2
4
6
8
10
12
14
16
18
20
22
24
Definition
+3.3V
+5V
+5V
PS_PWRGD
+12V
+3.3V
-12V
PSON# R
GND
-5V
+5V
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
SATA3.0 Connectors
CFast Slot
Connector type: Standard Serial ATAIII 7P (1.27mm, SATA-M-180)
Connector location: SATA1 and SATA2
Connector location: CFAST1
P17
1
S7
7
SATA1
Pin
1
3
5
7
Definition
GND
SATA_TXN0
SATA_RXN0
GND
Pin
2
4
6
Definition
SATA_TXP0
GND
SATA_RXP0
Definition
GND
SATA_TXN1
SATA_RXN1
GND
Pin
2
4
6
Definition
SATA_TXP1
GND
SATA_RXP1
Pin
S1
S3
S5
S7
P1
P3
P5
P7
P9
P11
P13
P15
P17
MH2
SATA2
Pin
1
3
5
7
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
43
Definition
GND
SATA_TXN2
SATA_RXN2
GND
GND
NC
NC
GND
NC
NC
+3.3V
GND
NC
GND
Pin
S2
S4
S6
Definition
SATA_TXP2
GND
SATA_RXP2
P2
P4
P6
P8
P10
P12
P14
P16
MH1
GND
NC
NC
TEST POINT
NC
NC
+3.3V
GND
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
PEG x16 Slot
Connector location: JPCIE1
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
Definition
NC
+12V
+12V
GND
GND
+3.3V
NC
+3.3V
+3.3V
+3.3V
CB_RESET#
GND
PCIE_X16_CLKP
PCIE_X16_CLKN
GND
PEG_RX0P
PEG_RX0N
GND
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
+12V
+12V
+12V
GND
SMB_CLK
SMB_DATA
GND
+3.3V
GND
+3.3VSBY
PCIE_WAKE#
NC
GND
PEG_TX0P
PEG_TX0N
GND
SDVO_CTRLCLK
GND
Pin
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
44
Definition
NC
GND
PEG_RX1P
PEG_RX1N
GND
GND
PEG_RX2P
PEG_RX2N
GND
GND
PEG_RX3P
PEG_RX3N
GND
NC
NC
GND
PEG_RX4P
PEG_RX4N
Pin
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
Definition
PEG_TX1P
PEG_TX1N
GND
GND
PEG_TX2P
PEG_TX2N
GND
GND
PEG_TX3P
PEG_TX3N
GND
NC
SDVO_CTRLDATA
GND
PEG_TX4P
PEG_TX4N
GND
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
Definition
GND
GND
PEG_RX5P
PEG_RX5N
GND
GND
PEG_RX6P
PEG_RX6N
GND
GND
PEG_RX7P
PEG_RX7N
GND
NC
GND
PEG_RX8P
PEG_RX8N
GND
GND
PEG_RX9P
PEG_RX9N
GND
GND
Pin
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
PEG_TX5P
PEG_TX5N
GND
GND
PEG_TX6P
PEG_TX6N
GND
GND
PEG_TX7P
PEG_TX7N
GND
NC
GND
PEG_TX8P
PEG_TX8N
GND
GND
PEG_TX9P
PEG_TX9N
GND
GND
PEG_TX10P
PEG_TX10N
Pin
A60
A61
A62
A63
A64
A65
A66
A67
A68
A69
A70
A71
A72
A73
A74
A75
A76
A77
A78
A79
A80
A81
A82
45
Definition
PEG_RX10P
PEG_RX10N
GND
GND
PEG_RX11P
PEG_RX11N
GND
GND
PEG_RX12P
PEG_RX12N
GND
GND
PEG_RX13P
PEG_RX13N
GND
GND
PEG_RX14P
PEG_RX14N
GND
GND
PEG_RX15P
PEG_RX15N
GND
Pin
B60
B61
B62
B63
B64
B65
B66
B67
B68
B69
B70
B71
B72
B73
B74
B75
B76
B77
B78
B79
B80
B81
B82
Definition
GND
GND
PEG_TX11P
PEG_TX11N
GND
GND
PEG_TX12P
PEG_TX12N
GND
GND
PEG_TX13P
PEG_TX13N
GND
GND
PEG_TX14P
PEG_TX14N
GND
GND
PEG_TX15P
PEG_TX15N
GND
NC
NC
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Digital Display Interface (Port B/ DDI #1)
Connector location: JDDI1
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
Definition
NC
+12V
+12V
GND
NC
NC
NC
NC
+3.3V
+3.3V
NC
GND
NC
NC
NC
SDVO_TVCLKIN_5P
SDVO_TVCLKIN_5N
GND
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
+12V
+12V
+12V
GND
NC
NC
GND
+3.3V
NC
+3.3VSBY
NC
NC
GND
SDVO_RED_0P
SDVO_RED_0N
GND
DDI1_CTRLCLK_AUXP
GND
Pin
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
46
Definition
NC
GND
SDVO_INT_4P
SDVO_INT_4NW
NC
NC
SDVO_FLDSTALL_6P
SDVO_FLDSTALL_6N
GND
GND
NC
NC
GND
NC
NC
GND
NC
NC
Pin
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
Definition
SDVO_GRN_1P
SDVO_GRN_1N
GND
GND
SDVO_BLU_2P
SDVO_BLU_2N
GND
GND
SDVO_CK_3P
SDVO_CK_3N
GND
NC
DDI1_CTRLDATA_AUXN
GND
NC
NC
GND
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
Definition
GND
GND
NC
NC
GND
GND
NC
NC
GND
GND
NC
NC
GND
NC
GND
NC
NC
GND
GND
NC
NC
GND
GND
Pin
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
NC
NC
GND
GND
DP1_HPD
NC
GND
GND
NC
NC
GND
NC
GND
NC
NC
GND
GND
NC
NC
GND
GND
NC
NC
Pin
A60
A61
A62
A63
A64
A65
A66
A67
A68
A69
A70
A71
A72
A73
A74
A75
A76
A77
A78
A79
A80
A81
A82
47
Definition
NC 0
NC
GND
GND
NC
NC 1
GND
GND
NC
NC
GND
GND
NC
NC
GND
GND
NC
NC
GND
GND
NC
NC
GND
Pin
B60
B61
B62
B63
B64
B65
B66
B67
B68
B69
B70
B71
B72
B73
B74
B75
B76
B77
B78
B79
B80
B81
B82
Definition
GND
GND
NC
NC
GND
GND
NC
NC
GND
GND
NC
NC
GND
GND
NC
NC
GND
GND
NC
NC
GND
DDI1_DDC_AUX_SEL
NC
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
PCIe x4
Connector location: JPCIE2
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A0
A11
A12
A13
A14
A15
A16
Definition
GND
+12V
+12V
GND
NC
NC
NC
NC
+3.3V
+3.3V
CB_RESET#
GND
PCIE_X4_CLKP
PCIE_X4_CLKN
GND
PCIE_RX0P
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
+12V
+12V
+12V
GND
SMB_CLK
SMB_DATA
GND
+3.3V
NC
+3.3VSBY
PCIE_WAKE#
NC
GND
PCIE_TX0P
PCIE_TX0N
GND
Pin
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
48
Definition
PCIE_RX0N
GND
NC
GND
PCIE_RX1P
PCIE_RX1N
GND
GND
PCIE_RX2P
PCIE_RX2N
GND
GND
PCIE_RX3P
PCIE_RX3N
GND
NC
Pin
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
Definition
NC
GND
PCIE_TX1P
PCIE_TX1N
GND
GND
PCIE_TX2P
PCIE_TX2N
GND
GND
PCIE_TX3P
PCIE_TX3N
GND
NC
NC
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
PCIe x1 Slots
Connector location: JPCIE3 and JPCIE4
JPCIE3
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
JPCIE4
Definition
GND
+12V
+12V
GND
NC
NC
NC
NC
+3.3V
+3.3V
CB_RESET#
GND
PCIE_X1_CLK0P
PCIE_X1_CLK0N
GND
PCIE_RX4P
PCIE_RX4N
GND
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
+12V
+12V
+12V
GND
SMB_CLK
SMB_DATA
GND
+3.3V
NC
+3.3VSBY
PCIE_WAKE#
NC
GND
PCIE_TX4P
PCIE_TX4N
GND
NC
GND
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
49
Definition
GND
+12V
+12V
GND
NC
NC
NC
NC
+3.3V
+3.3V
CB_RESET#
GND
PCIE_X1_CLK4P
PCIE_X1_CLK4N
GND
PCIEX1_RX7P
PCIEX1_RX7N
GND
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
Definition
+12V
+12V
+12V
GND
SMB_CLK
SMB_DATA
GND
+3.3V
NC
+3.3VSBY
PCIE_WAKE#
NC
GND
PCIEX1_TX7P
PCIEX1_TX7N
GND
NC
GND
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Mini-PCIe Slot (Wi-Fi and 3G)
Connector location: MPCIE1
1
2
51
52
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
Definition
PCIE_WAKE#
NC
NC
3VSB_MINI
GND
PMINI1_REFCLKN
MINI1_REFCLKP
GND
NC
NC
GND
PCIE_RXN5
PCIE_RXP5
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
27
29
31
33
35
37
39
41
43
45
47
49
51
Definition
3VSB_MINI
GND
1V5
UIM_PWR
UIM_DATA
UIM_CLK
UIM_RESET
UIM_VPP
GND
3VSB_MINI
MINI1_RST#
3VSB_MINI
GND
50
Definition
GND
GND
MINI1_TXN
MINI1_TXP
GND
GND
3VSB_MINI
3VSB_MINI
GND
NC
NC
NC
NC
Pin
28
30
32
34
36
38
40
42
44
46
48
50
52
Definition
1V5
SMB_CLK
SMB_DATA
GND
USB_4N
USB_4P
GND
NC
NC
NC
1V5
GND
3VSB_MINI
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Mini-PCIe Slot (mSATA)
Connector location: MSATA1
1
2
51
52
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
Definition
NC
NC
NC
NC
GND
NC
NC
GND
NC
NC
GND
SATA_RX3P
SATA_RX3N
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
27
29
31
33
35
37
39
41
43
45
47
49
51
Definition
+3.3V
GND
1V5_MSATA
NC
NC
NC
NC
NC
GND
NC
NC
+3.3V
GND
51
Definition
GND
GND
SATA_TXN3
SATA_TXP3
GND
GND
+3.3V
+3.3V
GND
TEST POINT
TEST POINT
NC
+3.3V
Pin
28
30
32
34
36
38
40
42
44
46
48
50
52
Definition
1V5_MSATA
SMBCLK_MAIN
SMBDATA_MAIN
GND
NC
NC
GND
NC
NC
NC
1V5_MSATA
GND
+3.3V
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
SIM Card Slot
Connector location: SIM1
C3
C2
C1
C7
C6
C5
Pin
C1
C2
C3
Definition
UIM_PWR
UIM_RESET
UIM_CLK
Pin
C5
C6
C7
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND
UIM_VPP
UIM_DATA
52
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
High Speed Board-to-Board Connector: Row A and B, Row C and D
Connector location: J1
Com Express A&B Connector
Com Express C&D Connector
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
Definition
GND(FIXED)
LAN1_MDI3N
LAN1_MDI3P
LAN1_LED_LINK100#
LAN_LED_LINK1G#
LAN1_MDI2N
LAN1_MDI2P
GBE0_LINK#
LAN1_MDI1N
LAN1_MDI1P
GND(FIXED)
LAN1_MDI0N
LAN1_MDI0P
Pin
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND(FIXED)
LAN1_LED_ACT#
LPC_FRAME#
LPC_AD0
LPC_AD1
LPC_AD2
LPC_AD3
LPC_DRQ0#
LPC_DRQ1#
LPC_CLK
GND(FIXED)
PM_PWRBTN#
SMB_CLK
Pin
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
53
Definition
GND(FIXED)
GND
USB3_RX0_N
USB3_RX0_P
GND
USB3_RX1_N
USB3_RX1_P
GND
USB3_RX2_N
USB3_RX2_P
GND(FIXED)
USB3_RX3_N
USB3_RX3_P
Pin
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
Definition
GND(FIXED)
GND
USB3_TX0_N
USB3_TX0_P
GND
USB3_TX1_N
USB3_TX1_P
GND
USB3_TX2_N
USB3_TX2_P
GND(FIXED)
USB3_TX3_N
USB3_TX3_P
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
Definition
LAN_CTREF
PM_SLP_S3#
SATA_TX0P
SATA_TX0N
PM_SLP_S4#
SATA_RX0P
SATA_RX0N
GND(FIXED)
SATA_TX2P
SATA_TX2N
PM_SLP_S5#
SATA_RXP2
SATA_RXN2
PM_BATLOW#
ICH_SATA_LED#
HDA_SYNC
HDA_RST#
GND(FIXED)
HDA_BIT_CLK
HDA_SDOUT
BIOS_DIS0#
PM_THRMTRIP#
USB_6N
USB_6P
USB_OC67#
USB_4N
USB_4P
GND(FIXED)
Pin
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
SMB_DATA
SMB_ALERT#
SATA_TX1P
SATA_TX1N
SUS_STAT#
SATA_RX1P
SATA_RX1N
GND(FIXED)
SATA_TX3P
SATA_TX3N
PS_PWRGD_CE
SATA_RX3P
SATA_RX3N
GAL_WDT#
HDA_SDIN2
HDA_SDIN1
HDA_SDIN0
GND(FIXED)
HDA_SPKR
I2C_CLK_CE
I2C_DAT_CE
PM_THRM#
USB_7N
USB_7P
USB_OC45#
USB_5N
USB_5P
GND(FIXED)
Pin
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C36
C37
C38
C39
C40
C41
54
Definition
GND
SDVO_FLDSTALL_6P
SDVO_FLDSTALL_6N
NC
NC
PCIE_RX6_LAN2P
PCIE_RX6_LAN2N
GND(FIXED)
PCIEX1_RX7P
PCIEX1_RX7N
DP1_HPD
SDVO_INT_4P
SDVO_INT_4N
NC
NC
SDVO_TVCLKIN_5P
SDVO_TVCLKIN_5N
GND(FIXED)
DDI2_CTRLCLK_AUXP
DDI2_CTRLDATA_AUXN
DP2_CTRL_AUX_SEL
NC
DDI3_CTRLCLK_AUXP
DDI3_CTRLDATA_AUXN
DP3_CTRL_AUX_SEL
DP3_LANE0P
DP3_LANE0N
GND(FIXED)
Pin
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
D32
D33
D34
D35
D36
D37
D38
D39
D40
D41
Definition
GND
DDI1_CTRLCLK_AUXP
DDI1_CTRLDATA_AUXN
NC
NC
PCIE_TX6_LAN2P
PCIE_TX6_LAN2N
GND(FIXED)
PCIEX1_TX7P
PCIEX1_TX7N
NC
NC
SDVO_RED_0P
SDVO_RED_0N
NC
SDVO_GRN_1P
SDVO_GRN_1N
GND(FIXED)
SDVO_BLU_2P
SDVO_BLU_2N
DDI1_DDC_AUX_SEL
NC
SDVO_CK_3P
SDVO_CK_3N
NC
DP2_LANE0P
DP2_LANE0N
GND(FIXED)
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
A63
A64
A65
A66
A67
A68
A69
Definition
USB_2N
USB_2P
USB_OC23#
USB_0N
USB_0P
+VBAT
EXCD0_PERST#
EXCD0_CPPE#
INT_SERIRQ
GND(FIXED)
PCIE_TX5P
PCIE_TX5N
ICH_GPI0
PCIE_TX4P
PCIE_TX4N
GND(FIXED)
PCIE_TX3P
PCIE_TX3N
GND(FIXED)
PCIE_TX2P
PCIE_TX2N
ICH_GPI1
PCIE_TX1P
PCIE_TX1N
GND(FIXED)
ICH_GPI2
PCIE_TX0P
PCIE_TX0N
Pin
B42
B43
B44
B45
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
B63
B64
B65
B66
B67
B68
B69
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
USB_3N
USB_3P
USB_OC01#
USB_1N
USB_1P
NC
NC
HW_RST#
CB_RESET#
GND(FIXED)
PCIE_RX5P
PCIE_RX5N
ICH_GPO1
PCIE_RX4P
PCIE_RX4N
ICH_GPO2
PCIE_RX3P
PCIE_RX3N
GND(FIXED)
PCIE_RX2P
PCIE_RX2N
ICH_GPO3
PCIE_RX1P
PCIE_RX1N
PCIE_WAKE#
WAKE1#
PCIE_RX0P
PCIE_RX0N
Pin
C42
C43
C44
C45
C46
C47
C48
C49
C50
C51
C52
C53
C54
C55
C56
C57
C58
C59
C60
C61
C62
C63
C64
C65
C66
C67
C68
C69
55
Definition
DP3_LANE1P
DP3_LANE1N
DP3_HPD
NC
DP3_LANE2P
DP3_LANE2N
NC
DP3_LANE3P
DP3_LANE3N
NC
PEG_RX0P
PEG_RX0N
TYPE0#
PEG_RX1P
PEG_RX1N
TYPE1#
PEG_RX2P
PEG_RX2N
GND(FIXED)
PEG_RX3P
PEG_RX3N
NC
NC
PEG_RX4P
PEG_RX4N
NC
PEG_RX5P
PEG_RX5N
Pin
D42
D43
D44
D45
D46
D47
D48
D49
D50
D51
D52
D53
D54
D55
D56
D57
D58
D59
D60
D61
D62
D63
D64
D65
D66
D67
D68
D69
Definition
DP2_LANE1P
DP2_LANE1N
DP2_HPD
NC
DP2_LANE2P
DP2_LANE2N
NC
DP2_LANE3P
DP2_LANE3N
GND(FIXED)
PEG_TX0P
PEG_TX0N
PEG_LANE_RV#
PEG_TX1P
PEG_TX1N
TYPE2#
PEG_TX2P
PEG_TX2N
GND(FIXED)
PEG_TX3P
PEG_TX3N
NC
NC
PEG_TX4P
PEG_TX4N
GND
PEG_TX5P
PEG_TX5N
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A70
A71
A72
A73
A74
A75
A76
A77
A78
A79
A80
A81
A82
A83
A84
A85
A86
A87
A88
A89
A90
A91
A92
A93
A94
A95
A96
A97
Definition
GND(FIXED)
LVDSA_DATA0P
LVDSA_DATA0N
LVDSA_DATA1P
LVDSA_DATA1N
LVDSA_DATA2P
LVDSA_DATA2N
LVDS_VDD_EN
LVDSA_DATA3P
LVDSA_DATA3N
GND(FIXED)
LVDSA_CLKP
LVDSA_CLKN
LVDS_DDC_CLK
LVDS_DDC_DATA
ICH_GPI3
KB_RST#
KB_A20GATE
PCIE0_CK_REFP
PCIE0_CK_REFN
GND(FIXED)
SPI_POWER
SPI_MISO
ICH_GPO0
SPI_CLK
SPI_MOSI
NC
TYPE10#
Pin
B70
B71
B72
B73
B74
B75
B76
B77
B78
B79
B80
B81
B82
B83
B84
B85
B86
B87
B88
B89
B90
B91
B92
B93
B94
B95
B96
B97
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
GND(FIXED)
LVDSB_DATA0P
LVDSB_DATA0N
LVDSB_DATA1P
LVDSB_DATA1N
LVDSB_DATA2P
LVDSB_DATA2N
LVDSB_DATA3P
LVDSB_DATA3N
L_BKLT_EN
GND(FIXED)
LVDSB_CLKP
LVDSB_CLKN
L_BKLT_CTRL
+5VSBY
+5VSBY
+5VSBY
+5VSBY
BIOS_DIS1#
CRT_RED
GND(FIXED)
CRT_GREEN
CRT_BLUE
CRT_HSYNC
CRT_VSYNC
CRT_DDC_CLK_MCH
CRT_DDC_DATA_MCH
SPI_CS#
Pin
C70
C71
C72
C73
C74
C75
C76
C77
C78
C79
C80
C81
C82
C83
C84
C85
C86
C87
C88
C89
C90
C91
C92
C93
C94
C95
C96
C97
56
Definition
GND(FIXED)
PEG_RX6P
PEG_RX6N
GND
PEG_RX7P
PEG_RX7N
GND
NC
PEG_RX8P
PEG_RX8N
GND(FIXED)
PEG_RX9P
PEG_RX9N
NC
GND
PEG_RX10P
PEG_RX10N
GND
PEG_RX11P
PEG_RX11N
GND(FIXED)
PEG_RX12P
PEG_RX12N
GND
PEG_RX13P
PEG_RX13N
GND
NC
Pin
D70
D71
D72
D73
D74
D75
D76
D77
D78
D79
D80
D81
D82
D83
D84
D85
D86
D87
D88
D89
D90
D91
D92
D93
D94
D95
D96
D97
Definition
GND(FIXED)
PEG_TX6P
PEG_TX6N
GND
PEG_TX7P
PEG_TX7N
GND
NC
PEG_TX8P
PEG_TX8N
GND(FIXED)
PEG_TX9P
PEG_TX9N
NC
GND
PEG_TX10P
PEG_TX10N
GND
PEG_TX11P
PEG_TX11N
GND(FIXED)
PEG_TX12P
PEG_TX12N
GND
PEG_TX13P
PEG_TX13N
GND
PEG_ENABLE#
ICEK 668-T6 Starter Kit User Manual
Chapter 2: Jumpers and Connectors
Pin
A98
A99
A100
A101
A102
A103
A104
A105
A106
A107
A108
A109
A110
Definition
SER0_TX
SER0_RX
GND(FIXED)
SER1_TX
SER1_RX
NC
+12V
+12V
+12V
+12V
+12V
+12V
GND(FIXED)
Pin
B98
B99
B100
B101
B102
B103
B104
B105
B106
B107
B108
B109
B110
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
NC
NC
GND(FIXED)
FANOUT
FANIN
SLEEP#
+12V
+12V
+12V
+12V
+12V
+12V
GND(FIXED)
Pin
C98
C99
C100
C101
C102
C103
C104
C105
C106
C107
C108
C109
C110
57
Definition
PEG_RX14P
PEG_RX14N
GND(FIXED)
PEG_RX15P
PEG_RX15N
GND
+12V
+12V
+12V
+12V
+12V
+12V
GND(FIXED)
Pin
D98
D99
D100
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
Definition
PEG_TX14P
PEG_TX14N
GND(FIXED)
PEG_TX15P
PEG_TX15N
GND
+12V
+12V
+12V
+12V
+12V
+12V
GND(FIXED)
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
Chapter 3: System Setup
1. Place the case on a stable surface and pull the yellow clasp to release the lock.
The starter kit is preconfigured and assembled. No addtional
setup is required. However, if installation is needed, please
refer to the instructions below.
Setting up the System
CAUTION!
Make sure the power supply is switched off and disconnected
from the power sources to prevent electric shock or system
damage before installing.
Clasp
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
58
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
2. Open the case.
3. Align the mounting holes on the ICEB 8060 mainboard to the mounting holes inside the case.
ATX
Connector
Mounting
holes
4. Tighten screws onto the holes to secure the mainboard, and plug the ATX power supply connector to the ATX connector on the motherboard.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
59
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
5. Locate the COM Express connector on the mainboard.
6. Install the ICES 668 module onto the COM Express connector.
Mounting holes
7. Align the mounting holes on the ICES 668 to the heatsink mounting holes on the mainboard.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
60
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
10. Align the mounting holes on the LCD panel to the mounting holes on
top of the case.
8. Once the holes are aligned, place the heatsink fan on top and tighten mounting screws to secure the heatsink.
Mounting screws
CFast card
CFast slot
Mounting holes
9. Insert the CFast card into the CFast slot.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
11. Tighten screws onto the mounting holes to secure the LCD panel.
61
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
12. Connect the LVDS and CCFL cables to the LVDS and CCFL connector
on the mainboard.
13. Plug the AC power cord to the power supply and connect the other
end to a power outlet. Then switch on the system.
AC Power
CCFL
LVDS
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
62
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
There is a metal plate supporting the mainboard that can be lifted up or
lowered down. The instructions below illustrate the step-by-step procedures.
1. Hold on the left and right spring-nuts using both hands, and pull out the spring-nuts to lift up or lower down.
NOTE: Before lifting up or lowering down, make sure the two spring-nuts
located on the left and right side of metal support plate are inserted/closed
to the end-position as depicted in the diagram below.
2. After lifting up the mainboard, make sure the two spring-nuts are
inserted and closed in the end-position before plugging any connectors and I/O cards, then power on the system.
3. After lowering down the mainboard, make sure the two spring-nuts are inserted and closed to the end position before powering off the system and closing the cover.
Left spring-nut
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Right spring-nut
63
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
External Soft-Power On/Off and Hardware Reset Switches
There are two special switches included inside the case to connect to JP18
and JP17 connectors for soft-power on/off and hardware reset function.
JP18: Soft-power on/off (red and black)
JP17: Hardware reset switch (green and black)
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
64
ICEK 668-T6 Starter Kit User Manual
Chapter 3: System Setup
Closing the Case
1. After lowering down the mainboard, make sure the two spring-nuts are inserted and closed to the end position before powering off.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
2. Make sure to place the LCD cover protector onto the LCD panel before closing the case.
65
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Chapter 4: BIOS Setup
This chapter describes how to use the BIOS setup program for the
ICEK 668-T6. The BIOS screens provided in this chapter are for reference only
and may change if the BIOS is updated in the future.
The settings made in the setup program affect how the computer performs.
It is important, therefore, first to try to understand all the setup options, and
second, to make settings appropriate for the way you use the computer.
To check for the latest updates and revisions, visit the NEXCOM Web site at
www.nexcom.com.tw.
When to Configure the BIOS
▪▪ This program should be executed under the following conditions:
About BIOS Setup
▪▪ When changing the system configuration
▪▪ When a configuration error is detected by the system and you are
prompted to make changes to the setup program
The BIOS (Basic Input and Output System) Setup program is a menu driven
utility that enables you to make changes to the system configuration and
tailor your system to suit your individual work needs. It is a ROM-based
configuration utility that displays the system’s configuration status and
provides you with a tool to set system parameters.
▪▪ When resetting the system clock
▪▪ When redefining the communication ports to prevent any conflicts
▪▪ When making changes to the Power Management configuration
These parameters are stored in non-volatile battery-backed-up CMOS RAM that
saves this information even when the power is turned off. When the system is
turned back on, the system is configured with the values found in CMOS.
▪▪ When changing the password or making other changes to the security
setup
Normally, CMOS setup is needed when the system hardware is not consistent
with the information contained in the CMOS RAM, whenever the CMOS
RAM has lost power, or the system features need to be changed.
With easy-to-use pull down menus, you can configure such items as:
▪▪ Hard drives, diskette drives, and peripherals
▪▪ Video display type and display options
▪▪ Password protection from unauthorized use
▪▪ Power management features
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
66
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Default Configuration
Legends
Most of the configuration settings are either predefined according to
the Load Optimal Defaults settings which are stored in the BIOS or are
automatically detected and configured without requiring any actions. There
are a few settings that you may need to change depending on your system
configuration.
Key
Moves the highlight left or right to select a menu.
Moves the highlight up or down between
sub¬menus or fields.
Entering Setup
Exits the BIOS Setup Utility.
When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines. These routines perform various diagnostic checks; if an
error is encountered, the error will be reported in one of two different ways:
Scrolls forward through the values or options of the
highlighted field.
Scrolls backward through the values or options of
the highlighted field.
▪▪ If the error occurs before the display device is initialized, a series of beeps
will be transmitted.
Selects a field.
▪▪ If the error occurs after the display device is initialized, the screen will
display the error message.
Displays General Help.
Load previous values.
Powering on the computer and immediately pressing <Del> allows you to
enter Setup. Another way to enter Setup is to power on the computer and
wait for the following message during the POST:
TO ENTER SETUP BEFORE BOOT PRESS
Function
Ctrl
+
Alt
Load optimized default values.
Saves and exits the Setup program.
+
Press <Enter> to enter the highlighted sub¬menu
Press the
key to enter Setup:
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
67
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Scroll Bar
When a scroll bar appears to the right of the setup screen, it indicates that
there are more available fields not shown on the screen. Use the up and
down arrow keys to scroll through all the available fields.
Submenu
When “” appears on the left of a particular field, it indicates that a
submenu which contains additional options are available for that field. To
display the submenu, move the highlight to that field and press
.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
68
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
BIOS Setup Utility
System Date
The date format is <day>, <month>, <date>, <year>. Day displays a day,
from Monday to Sunday. Month displays the month, from January to
December. Date displays the date, from 1 to 31. Year displays the year, from
1999 to 2099.
Once you enter the AMI BIOS Setup Utility, the Main Menu will appear on
the screen. The main menu allows you to select from several setup functions
and one exit. Use arrow keys to select among the items and press
to
accept or enter the submenu.
System Time
The time format is <hour>, <minute>, <second>. The time is based on the
24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays
hours from 00 to 23. Minute displays minutes from 00 to 59. Second displays
seconds from 00 to 59.
Main
The Main menu is the first screen that you will see when you enter the BIOS
Setup Utility.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
BIOS Information
BIOS Vendor
Core Version
Compliancy
Project Version
Build Date and Time
American Megatrends
4.6.5.3
UEFI 2.3; PI 1.2
I668-007
08/17/2012 11:56:07
Memory Information
Memory Frequency
Total Memory
DIMM#0
DIMM#2
1333 Mhz
2048 MB (DDR3)
Not Present
2048 MB (DDR3)
ME
ME
ME
ME
8.0.0.1351
Normal Mode
5MB
Firmware Information
FW Version
Firmware Mode
Firmware SKU
System Date
System Time
[Tue 08/21/2012]
[16:37:54]
Save & Exit
Set the Date. Use Tab to switch
between Date elements.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
69
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Advanced
ACPI Settings
This section is used to configure ACPI Settings.
The Advanced menu allows you to configure your system for basic operation.
Some entries are defaults required by the system board, while others, if
enabled, will improve the performance of your system or let you set some
features according to your preference.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
Chipset
PCIPnP
Security
ACPI Settings
Enable Hibernation
ACPI Sleep State
Setting incorrect field values may cause the system to
malfunction.
[Enabled]
[S3 only(Suspend to...)]
Exit
Enables or Disables System
ability to Hibernate (OS/S4 Sleep
State). This option may be not
effective with some OS.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
ACPI Settings
CPU Configuration
SATA Configuration
AMT Configuration
USB Configuration
H/W Monitor
F81216 Second Super IO Configuration
Super IO Configuration
CPU PPM Configuration
Save & Exit
System ACPI Parameters
←
↑↓ +/- Tab
F1
F10 ESC Select Screen
Select Item
Change Field
Select Field
General Help
Save & Exit
Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Enable Hibernation
Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This
option may be not effective with some OS.
ACPI Sleep State
Select the highest ACPI sleep state the system will enter when the suspend
button is pressed. The options are Suspend Disabled, S1 (CPU Stop Clock)
and S3 (Suspend to RAM).
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
70
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
CPU Configuration
SATA Configuration
This section is used to configure the CPU.
This section is used to configure the SATA drives.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Advanced
CPU Configuration
Intel(R) Core(TM) i3-3217UE CPU @ 1.60GHz
306a8
CPU Signature
10
Microcode Patch
1500 MHZ
CPU Speed
2
Processor Cores
Supported
Intel HT Technology
Supported
Intel VT-x Technology
Not Supported
Intel SMX Technology
Supported
64-bit
Hyper-Threading
Intel Virtualization Technology
[Enabled]
[Disabled]
Enabled for Windows XP and
Linux (OS optimized for HyperThreading Technology) and
Disabled for other OS (OS not
optimized for Hyper-Threading
Technology). When Disabled
only one thread per enabled core
is enabled.
SATA Controller(s)
SATA Mode Selection
[Enabled]
[IDE]
Serial ATA Port 0
Software Preserve
Serial ATA Port 1
Software Preserve
Empty
Unknown
Empty
Unknown
Enable or disable SATA Device.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Hyper-Threading
SATA Controller(s)
This field is used to enable or disable hyper-threading.
Enables or disables the SATA controller.
Intel® Virtualization Technology
Enables or disables Intel® Virtualization technology.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
71
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
SATA Mode Selection
AMT Configuration
Configures the SATA as IDE, AHCI or RAID mode.
This section is used to configure Active Management Technology (AMT)
options.
IDE
RAID
AHCI
This option configures the Serial ATA drives as Parallel ATA physical storage device.
This option allows you to create RAID or Intel Matrix Storage configuration on Serial ATA devices.
This option configures the Serial ATA drives to use AHCI (Advanced Host Controller Interface). AHCI allows the storage driver to enable the advanced Serial ATA features which will increase storage performance.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel AMT[Enabled]
BIOS Hotkey Pressed
[Disabled]
MEBx Selection Screen
[Disabled]
Enable/Disable Intel (R) Active
Mangement Technology BIOS
Extension.
Note: iAMT H/W is always
enabled.
This option just controls the
BIOS extension execution. If
enabled, this requires addtional
firmware in the SPI device.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Intel® AMT
Enables or disables Intel® Active Management Technology.
BIOS Hotkey Pressed
Enables or disables BIOS hotkey press.
MEBx Selection Screen
Enables or disables MEBx selection screen.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
72
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
USB Configuration
Port 60/64 Emulation
This section is used to configure the USB.
Enables the 60h/64h I/O port emulation. You must enable this to fully
support USB keyboard legacy for non-USB OSes.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
USB Configuration
Enables Legacy USB support.
AUTO option disables legacy
support if no USB devices are
connected. DISABLE option will
keep USB devices available
only for EFI applications.
USB Devices:
1 Keyboard, 1 Mouse, 2 Hubs
Legacy USB Support
USB3.0 Support
Port 60/64 Emulation
[Enabeld]
[Enabled]
[Enabled]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Legacy USB Support
Enable Enables Legacy USB.
Auto Disables support for Legacy when no USB devices are connected.
Disable Keeps USB devices available only for EFI applications.
USB3.0 Support
Enables or disables USB 3.0 controller support.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
73
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
H/W Monitor
VCORE
This section is used to monitor hardware status such as temperature, fan
speed and voltages.
Detects and displays the Vcore CPU voltage.
+5V
Detects and displays 5V voltage.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
+3.3V
Pc Health Status
cpu temperature1
System temperature1
Fan1 Speed
Fan2 Speed
VCORE
5V
3.3V
:
:
:
:
:
:
:
Detects and displays 3.3V voltage.
+41.25C
+31.875C
N/A
6000 RPM
+0.862
+5.096 V
+3.348 V
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
CPU Temperature1
Detects and displays the current CPU temperature.
System Temperature1
Detects and displays the current system temperature.
Fan1 Speed to Fan2 Speed
Detects and displays system fan1 and fan2 speeds.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
74
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
F81216 Second Super IO Configuration
Serial Port 0 Configuration
This section is used to configure serial ports 0 and 1.
This section is used to configure serial port 0.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Advanced
F81216 Second Super IO Configuration
F81216 Second Super IO Chip
 Serial Port 0 Configuration
 Serial Port 1 Configuration
Serial Port 0 Configuration
Set Parameters of Serial Port
0 (COMA)
F81216 SecondIo
Serial Port
Enable or Disable Serial Port
(COM)
[Disabled]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
F81216 Second Super IO Chip
Serial Port
Displays the Super I/O chip used on the board.
Enables or disables the serial port.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
75
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Serial Port 1 Configuration
This section is used to configure serial port 1.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Serial Port 1 Configuration
Serial Port
Enable or Disable Serial Port
(COM)
[Disabled]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Serial Port
Enables or disables the serial port.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
76
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Super IO Configuration
Serial Port 0 Configuration
This section is used to configure serial ports 1 to 5.
This section is used to configure serial port 0.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Advanced
Super IO Configuration
Super IO Chip
 Serial Port 1
 Serial Port 2
 Serial Port 3
 Serial Port 4
 Serial Port 5
Configuration
Configuration
Configuration
Configuration
Configuration
Serial Port 0 Configuration
Set Parameters of Serial Port
0 (COMA)
IT8783F
Enable or Disable Serial Port
(COM)
Serial Port
Device Settings
[Enabled]
IO=3F8h; IRQ=4;
Change Settings
[IO=3F8h; IRQ=4;]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Super IO Chip
Serial Port
Displays the Super I/O chip used on the board.
Enables or disables the serial port.
Change Settings
Selects an optimal setting for the Super IO device.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
77
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Serial Port 1 Configuration
Serial Port 2 Configuration
This section is used to configure serial port 1.
This section is used to configure serial port 2.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Advanced
Serial Port 1 Configuration
Serial Port 2 Configuration
Enable or Disable Serial Port
(COM)
Enable or Disable Serial Port
(COM)
Serial Port
Device Settings
[Enabled]
IO=2F8h; IRQ=3;
Serial Port
Device Settings
[Enabled]
IO=3E8h; IRQ=10;
Change Settings
[IO=2F8h; IRQ=3;]
Change Settings
[IO=3E8h; IRQ=10;]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Serial Port
Serial Port
Enables or disables the serial port.
Enables or disables the serial port.
Change Settings
Change Settings
Selects an optimal setting for the Super IO device.
Selects an optimal setting for the Super IO device.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
78
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Serial Port 3 Configuration
Serial Port 4 Configuration
This section is used to configure serial port 3.
This section is used to configure serial port 4.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Advanced
Serial Port 3 Configuration
Serial Port 4 Configuration
Enable or Disable Serial Port
(COM)
Enable or Disable Serial Port
(COM)
Serial Port
Device Settings
[Enabled]
IO=2E8h; IRQ=11;
Serial Port
Device Settings
[Enabled]
IO=2F0h; IRQ=6;
Change Settings
[IO=2E8h; IRQ=11;]
Change Settings
[IO=2F0h; IRQ=6;]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Serial Port
Serial Port
Enables or disables the serial port.
Enables or disables the serial port.
Change Settings
Change Settings
Selects an optimal setting for the Super IO device.
Selects an optimal setting for the Super IO device.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
79
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Serial Port 5 Configuration
CPU PPM Configuration
This section is used to configure serial port 5.
This section is used to configure the Processor Power Management (PPM)
configuration.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Advanced
Serial Port 4 Configuration
Enable or Disable Serial Port
(COM)
Serial Port
Device Settings
[Enabled]
IO=2E0h; IRQ=7;
Change Settings
[IO=2E0h; IRQ=7;]
CPU PPM Configuration
EIST
CPU C3 Report
CPU C6 Report
CPU C7 Report
Enable/Disable Intel SpeedStep
[Disabled]
[Disabled]
[Disabled]
[Disabled]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Serial Port
EIST
Change Settings
CPU C3 Report
Enables or disables the serial port.
Enables or disables Intel® SpeedStep.
Selects an optimal setting for the Super IO device.
Enables or disables C3 report to the operating system.
CPU C6 Report
Enables or disables C6 report to the operating system.
CPU C7 Report
Enables or disables C7 report to the operating system.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
80
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Chipset
PCH-IO Configuration
This section is used to configure the system based on the specific features
of the chipset.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
PCH-IO Configuration
System Agent (SA) Configuration
Chipset
Boot
Save & Exit
PCH Parameters
Security
Save & Exit
USB Configuration
settings
USB Configuration
PCH Azalia Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
PCH LAN Controller
Wake on LAN
[Enabled]
[Enabled]
Restore AC Power Loss
RTC RAM Lock
[Power On]
[Enabled]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PCH LAN Controller
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Enables or disables onboard NIC.
Wake on LAN
Setting incorrect field values may cause the system to
malfunction.
Enables or disables integrated LAN to wake the system.
Restore AC Power Loss
Select AC power state when power is re-applied after a power failure.
RTC RAM Lock
Enables or disables RTC RAM lock.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
81
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
USB Configuration
PCH Azalia Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
Chipset
USB Configuration
[Enabled]
[Enabled]
EHCI1
EHCI2
PCH Azalia Configuration
Control the USB EHCI (USB 2.0)
functions.
One EHCI controller must always
be enabled.
Azalia
[Enabled]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
EHCI1 and EHCI2
Azalia
Enables or disables the Enhanced Host Controller Interface (USB 2.0), one
EHCI controller must always be enabled.
Control Detection of the Azalia device.
Disabled
Enabled
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
Control Detection of the Azalia
device.
Disabled = Azalia will be
unconditionally disabled
Enabled = Azalia will be
unconditionally Enabled
Auto = Azalia will be enabled if
present, disabled otherwise.
82
Azalia will be unconditionally disabled.
Azalia will be unconditionally disabled.
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
System Agent (SA) Configuration
Graphics Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Graphics Configuration
NB PCIe Configuration
Save & Exit
Chipset
Config Graphics Settings.
Graphics Configuration
Primary Display
Internal Graphics
DVMT Total Gfx Mem
► LCD Control
[Enabled]
[Auto]
[256M]
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Select which of IGFX/PEG/
PCI Graphics device should be
Primary Display Or select SG for
Switchable Gfx.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Primary Display
Select which of IGFX/PEG/PCI graphics device should be primary display or
select SG for switchable GFx.
Internal Graphics
Keep IGD enabled based on the setup options.
DVMT Total Gfx Mem
Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics
Device.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
83
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
LCD Control
Active LFP
Select the Active LFP configuration.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
No LVDS
Int-LVDS
Chipset
LCD Control
Primary IGFX Boot Display
Secondary IGFX Boot Display
LCD Panel Type
Active LFP
Panel Color Depth
[CRT]
[Disabled]
[1024x768LVDS]
[No LVDS]
[18 Bit]
Select the Video Device which
will be activated during POST.
This has no effect if external
graphics present. Secondary boot
display selection will appear
based on your selection.
VGA modes will be supported
only on primary display
VBIOS does not enable LVDS.
VBIOS enables LVDS driver by Integrated encoder.
Panel Color Depth
Select the LFP Panel Color Depth.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Primary IGFX Boot Display
Select the video device which will be activated during POST. Has no effect
if external graphics is present. Secondary boot display selection will appear
based on your selection. VGA modes will be supported only on primary
display.
LCD Panel Type
Select the LCD panel used by the internal graphics device by selecting the
appropriate setup item.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
84
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
NB PCIe Configuration
This section is used to configure Northbridge PCI Express settings.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Chipset
NB PCIe Configuration
PEG0
PEGO - Gen X
Not Present
[Auto]
Enable PEG
[Enabled]
Configure PEG0 B0:D1:F0
Gen1-Gen3.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PEG0 - Gen X
Configure PEG0 B0:D1:F0 Gen1-Gen3.
Enable PEG
Enables or disables the PEG slot.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
85
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Boot
Security
This section is used to configure the boot features.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
Chipset
Quiet Boot
Launch PXE OpROM policy
Boot
Security
[Disabled]
[Disabled]
Save & Exit
Advanced
Chipset
Boot
Security
Password Description
Enables or disables Quiet Boot
option
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User Will
have Administrator rights.
The password length must be
in the following range:
Minimum length
3
Maximum20
Boot Option Priorities
Administrator Password
User Password
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Save & Exit
Set Administrator Password
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Administrator Password
Select this to reconfigure the administrator’s password.
Quiet Boot
Enabled
Disabled
Displays OEM logo instead of the POST messages.
Displays normal POST messages.
User Password
Select this to reconfigure the user’s password.
Launch PXE OpROM Policy
Controls the execution of UEFI and legacy PXE OpROM.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
86
ICEK 668-T6 Starter Kit User Manual
Chapter 4: BIOS Setup
Save & Exit
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save Changes and Reset
Discard Changes and Reset
Save & Exit
Reset the system after saving
the changes.
Load Optimized Defaults
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
Save Changes and Reset
To save the changes and reset, select this field then press <Enter>. A dialog
box will appear. Confirm by selecting Yes.
Discard Changes and Reset
To exit the Setup utility without saving the changes, select this field then
press <Enter>. You may be prompted to confirm again before exiting.
Load Optimized Defaults
To restore the BIOS to default settings, select this field then press <Enter>. A
dialog box will appear. Confirm by selecting Yes.
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
87
ICEK 668-T6 Starter Kit User Manual
Appendix A: Watchdog Timer
Appendix A: Watchdog Timer
WDT Programming Guide
ICES 668 Watch Dog Function Configuration Sequence Description:
Start
Step1. See “SetupWDT” procedure
#Setup Watchdog Timer Environment
Step2. See “TimeBaseWDT” procedure
#Initial Watchdog Timer.
Users can select second or minute.
Step3. See “TimeCountWDT” procedure
#Set Watchdog Timer Time-out Value.
Users can set time-out value.
Step4: See ExitSetup procedure
#Exit Setup Environment
End
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
88
ICEK 668-T6 Starter Kit User Manual
Appendix A: Watchdog Timer
mov
al, 03h ;Here!! Set count 3.
out2fh,al
ret
TimeCountWDTENDP
===============================================
SetupWDTPROC
mov
dx, 2eh
mov
al, 087h
outdx,al
nop
nop
out
dx,al
;Write operations to special address
port (2E) for entering MB PnP Mode.
===============================================
ExitSetupPROC
mov
al, 0AAh
out2eh,al
ret
ExitSetupENDP
===============================================
mov
al, 07h
out2eh,al
mov
al, 08h ;Select logical device for Watch Dog.
out2fh,al
ret
SetupWDTENDP
===============================================
TimeBaseWDT
PROC
moval,0F5h
out2eh,al
mov al, 04h; Here!! set 04h for second, set 0Ch for
minute(WDT output through WDTO)
out2fh,al
ret
TimeBaseWDTENDP
===============================================
TimeCountWDTPROC
mov
al,0F6h ;WDT Time-out register.
out2eh,al
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
89
ICEK 668-T6 Starter Kit User Manual
Appendix B: GPI/O Programming Guide
Appendix B: GPI/O Programming Guide
GPI/O (General Purpose Input/Output) pins are provided for custom system design.
This appendix provides definitions and its default setting for the ten GPI/O pins in the
ICES 668 series. The pin definition is shown in the following table:
Pin No.
GPI/O mode PowerOn
Default
Address
Pin No.
GPI/O mode PowerOn
Default
Address
1
VCC
-
-
2
GND
-
-
3
GPI0
Low
548h (Bit6)
4
GPO0
High
548h (Bit7)
5
GPI1
Low
50Eh (Bit1)
6
GPO1
High
50Ch (Bit7)
7
GPI2
Low
548h (Bit4)
8
GPO2
High
538h (Bit6)
9
GPI3
Low
548h (Bit5)
10
GPO3
High
538h (Bit7)
Control the GPO pin (3/5/7/9) level from I/O port 548h, 50Eh, 548h, 548h bit (6/1/4/5).
The bit is Set/Clear indicated output High/Low
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
90
ICEK 668-T6 Starter Kit User Manual
Appendix B: GPI/O Programming Guide
GPIO programming sample code
#define GPIO_PORT
#define GPIO_PORT3 #define GPO0
#define GPO1
#define GPO2
#define GPO3
0x50E
0x548
(0x01 << 6
(0x01 <<1)
(0x01 <<4)
(0x01 << 5)
#define GPO0_HI
#define GPO0_LO
#define GPO1_HI
#define GPO1_LO
#define GPO2_HI
#define GPO2_LO
#define GPO3_HI
#define GPO3_LO
void main(void)
{
GPO0_HI;
GPO1_LO;
GPO2_HI;
GPO3_LO;
outportb(GPIO_PORT3, GPO0)
outportb(GPIO_PORT3, 0x00)
outportb(GPIO_PORT, GPO1)
outportb(GPIO_PORT, 0x00)
outportb(GPIO_PORT3, GPO2)
outportb(GPIO_PORT3, 0x00)
outportb(GPIO_PORT3, GPO3)
outportb(GPIO_PORT3, 0x00)
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
91
ICEK 668-T6 Starter Kit User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement