Profile Parts and Tools Model and Specification Installation

Profile Parts and Tools Model and Specification Installation
2. Product parts and Self-provided tools:
Model and Specification
03
(1) Product Parts
(2) Self-provided tools
Galaxy Series
Series
Model
Z2009CA
Z2018CA
Z2118CA
Z2136CA
Color
White
White
White
White
Rated Power (W/PCS)
3.5
7
7
13
Working Voltage (V):
DC12
Working Environment Temperature (℃):
-25~60
Storage Temperature (℃):
-40~70
Galaxy Series
Products
Self –tapping Screw
(ST2.9)
04
Profile
Installation Holder
Z2009CA & Z2018CA Product Size:616*16*6.5
Electrical Drill
&Drilling Bit
T-wire
Installation & Application Examples
05
Space between
Strips(mm)
Installation
Quantity
(pcs)
dz=100
dy=60
16
4000-4300
6900-7000
dz=120
dy=80
12
2800-3200
4800-5400
dz=160
dy=120
8
1950-2100
3100-3700
dz=180
dy=140
7
1500-1600
2700-3000
Light Box
Thickness
(mm)
Z2118CA & Z2136CA Product Size:1198*16*6.5
1. Installation and Connection Illustration:
Z2009CA(9LEDs/0.6m) Z2018CA(18LEDs/0.6m)
06
07
Power Appearance (Only for reference)
Install Procedures
01
White wire(Cathode)
Grey wire(Anode)
Clean the installation surface
before installing.
08
T-wire Notes and Use
Parallel Connection of
Parallel Connection of
Parallel Connection of
Maximum Number Per 0.6m Maximum Number Per 1.2m Maximum Number Per 2.4m
Z2009CA
12PCS
12PCS
Z2018CA
12PCS
12PCS
12PCS
6PCS
Z2118CA
/
12PCS
12PCS
/
12PCS
6PCS
Don't use T-wire parallel connection if T-wire is not enough, and It must
be connected specially to power supply; Cut off T-wire and avoid short
circuit if maximum cascade number of T-wire exceed the original number.
02
Connect T-wire with bar terminal
line, and fix T-wire well.
Illumination Scope(lux)
Remark:
1, The above layout data are measured with 0.6m LED bars
which used Rishang's LED. The data for 1.2m LED bars
will be same under the same condition of use.
2, The example is tested with 3mm thickness white acrylic panel
which the transmittance is up to 54%.
3, Light box size: 600mm*1000mm.
4, The above layout data are measured with Rishang's LED.
Under the same condition of use, the brightness of Samsung's
LED will be more 30% than Rishang's LED.
5,The above data is for reference only.
Parts and Tools
Z2136CA
After installation holder fixed,
you shall fasten the bars and
arrange the layout parallel.
Unit : mm
Reference Scheme
Model
According to the drawn lines,
installation holder will be fixed
on the framework or light box
board.
Select the installation place and
quantity.
Fix the appropriate power supply,
and drill a hole near the end of
T-wire. The wire through the
hole must be fixed and protected
them well.
Connect LED bar to the power
supply's output end, beware of
the polarities, and prepare for
avoiding short circuit at both
wire ends.
Connect each two bar's wire
together (anode to anode and
cathode to cathode), if more
products are needed.
Note: The maximum cascade
length of the product is
2.4m. No exceeding!
NOTES
Warning
1.Installation notes:
1)Clean the installation surface before installing.
2) Make sure the polarity of the product and the power supply is
corrected linked, otherwise, the product can not be lightened.
3) Check the connection between the terminals of L ED bars with
the cord of the power supply, it is suitable to not be pull out by
hand .
2.Notes for other installation materials used:
1)Do not use any acid or alkaline adhesive to fix the product.
2)When installing the product, avoid the adhesive sticking to the
LED surface.
3)The standard product length is 2.4m. Please choose a switch
power supply that have short-circuit, over voltage and over
current protection functions. The tolerable output voltage range
of the power supply should be around ±5%.If more products are
needed, you must make sure the power supply's rated load is
15% or higher than it's real load.
This product is non-waterproof, indoor use only.
Do not disassemble or modify the light.
Do not install while the electricity cables are live.
Do not use any acid or alkaline adhesive to fix the product; when
using neutral silica glue to fix the product, do not store the
product until the neutral glass is cured in the open air.
The length of power cord cannot exceed 2m between power
supply and bar. But, the wire will be damaged increasingly and
bright difference.
Check if the wire installation is correct and if the power voltage
can meet the requirements before electrifying.
Don't use T-wire parallel connection if T-wire is not enough, and
It must be connected specially to power supply; Cut off T-wire
and avoid short circuit if maximum cascade number of T-wire
exceed the original number.
Warranty
Warranty: 3 years or 13,000 hours, whichever comes first.
Malfunction&Solutions Table
Galaxy Series LED Single-Side Bar
User Guide
Z2009CA,Z2018CA
Z2118CA,Z2136CA
Malfunction & Solutions Tables
Malfunctions
Non LED work
Possible Causes
Solutions
1,No power from the power supply.
Supply power.
2,The power supply is short circuit;
The switching power supply
automatically protected against
short-circuiting.
Remove any short-circuiting
malfunctions, re-electrify.
3,The polarity between the bars
and the input power supply is
reversed.
1, No output for the part of power
supply .
Part of the LED 2, Wrong polarity connected for the
part of the bars.
bars don't work
Brightness of
the LED is dim
or not even
LED are
blinking
Check the power supply and
remove malfunctions .
3,The polarity among some
products and the power supply's
are reversed.
Connected the wires rightly.
4,Part of T-wires connected
unusually.
Make T-wire connect rightly.
1,The power supply is over loaded.
Add more power.
2,The loss of the power supply's
wire is too big.
Make sure the bars' working
voltage is within 95%-105% of
the rated voltage.
3, The quantity of LED bars
cascaded too more.
Adjust the number of LED bars
for each power supply. Adjust
every electric circuit to the
largest bars amount required.
1,The connection are loosen.
Find the loosen connection and
remove any malfunctions.
2,Failures in the power supply.
Replace the power supply
Read this manual carefully before using this product and keep it!
V1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement