BOF2001-CN
pure indoor living
1500 Watt
OIL FILLER RADIATOR
MODEL
BOF2001-CN
INSTRUCTION MANUAL
If after having read this leaflet, you have any
questions or comments on your heater,
call 1-800-253-2764 in North America.
HEATER SAFETY
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be followed to reduce the risk
of fire, electric shock, and injury to persons, including the
following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance
directly into a 120V AC electrical outlet.
3. The heater is hot when in use. To avoid burns, DO NOT
let bare skin touch hot surfaces. If provided, use
handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 ft (0.9 m) from the front
of the heater and keep them away from the sides and
rear.
4. DO NOT run cord under carpeting. DO NOT cover cord
with throw rugs, runners, or the like. Arrange cord away
from traffic area and where it will not be tripped over.
5. This heater is not intended for use in bathrooms,
laundry areas and similar indoor location. NEVER locate
heater where it may fall into a bathtub or other water
container.
6. Extreme caution is necessary when any heater is used
by, or near children or invalids, and whenever the
heater is left operating and unattended.
7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not
the cord.
9. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
10.DO NOT operate heater with a damaged cord or plug,
or after the heater malfunctions, has been dropped or
damaged in any manner. Return appliance to
manufacturer for examination, electrical or mechanical
adjustment, or repair.
11.A heater has hot and arcing or sparking parts inside.
DO NOT use it in areas where gasoline, paint, or
flammable liquids are used or stored.
12.Use appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by the
manufacturer may cause hazards.
13.DO NOT use outdoors.
14.To prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces,
like a bed, where openings may become blocked.
15.To disconnect heater, turn controls to OFF, then remove
plug from outlet.
16.Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated not
less than 1875 watts.
17.To avoid overheating, do not cover the heater.
18.DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed by
qualified personnel only.
19.Discontinue use if plug or outlet is hot. It is
recommended that the outlet be replaced if plug or
outlet is hot to touch.
20.This heater is filled with a precise quantity of special oil.
Repairs requiring opening of the oil container are only to
be made by the manufacturer or service agent. In the
event of an oil leak contact the manufacturer or service
agent.
21.Regulations concerning the disposal of oil when
scrapping this appliance must be followed.
PLEASE SAVE THESE
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS APPLIANCE HAS A POLARIZED
AC PLUG (one blade is wider than the
other). To reduce the risk of electric
shock, this plug is intended to fit in a
polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a
qualified electrician to install the proper outlet.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR
DEFEAT THIS SAFETY FEATURE IN ANY WAY.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
TECHNICAL SPECIFICATIONS
• Wattage: 1500W (+5% -10%)
• Working voltage: 120V AC/60Hz
AUTO SAFETY SHUT-OFF WITH INSTANT TIP
OVER PROTECTION
This heater is equipped with an advanced safety system
if there is a potential overheat situation. When a potential
overheat temperature is reached, the system will
automatically shut the heater off. It can only resume
operation when the unit has cooled down.
Tip Over Shut-Off:
If the unit is tipped over in any direction, it will instantly
shut off. To reset, simply place the heater in an upright
position and press the mode button to reactivate the unit.
PRE-OPERATING & ASSEMBLY INSTRUCTIONS
(See Fig. 3)
Fig. 1
A
B
A. Heated Fins
B. Vents
C. Pull down handle
D. Power switch
E. Cord Storage
F. Power cord
G. Front castor
assembly
Q. Castor
C
F C
D
E
F
G
Q
1. Carefully remove your heater from the box and remove
foot plate x2 (G,R) and casters x4 (Q) from the Styrofoam
packing material. Please save the carton for off-season
storage.
2. Make sure the unit is in the OFF position and not
plugged into the outlet.
3. Turn the heater upside down, locate the 2 U-bolts (T)
installed on the bottom at both ends.
4. Unscrew the wing nuts (P,S) from the U-bolts (T).
Fig. 3
Q
G
P
R
S
T
G. Front castor assembly
P. Front wing nut
Q. Castor
R. Rear castor assembly
S. Rear wing nut
T. U-bolt
5. Place one hole of the foot plate to the L shape end of
the U-bolt on the other hole on the end of the U-bolt with
the threading and screw on the wing nut until the foot
plate is securely in place.
6. Repeat step 5 to install the remaining foot plate.
7. Use your hand to press the four casters onto the four
axis on the two foot plates until you hear them snap into
place. Use your hand to turn the casters and if
they move smoothly they have been installed properly.
8. Turn the heater right side up - your heater is now
ready for use.
BASIC OPERATING INSTRUCTIONS
(See Fig 1 & 2)
1. Ensure the power switch (D) is set to the OFF (O)
position
2. Plug in heater
3. Flip the power switch to the ON (-) position. The power
light (I) will illuminate red until the unit is unplugged.
4. Press the mode button (L) once to activate the unit. The
mode light (J) will glow green to indicate the heater is
running. The unit will automatically start on setting 3
(high heat).
5. Press the mode button until the desired heat setting is
shown on the display panel (H).
BOF2001-CN: 1=600W, 2=900W, 3=1500W,
(EC)= Heat & $ave™ Mode
H. Digital display
I. Power light
J. Mode light
K. Timer light
L. Mode button
M. Thermostat/timer button
N. Adjuster buttons
O. ˚F - ˚C button
Fig. 2
H
J
I
K
L
M
N
O
F C
After using the heater, press the mode button until the unit
is deactivated and the mode light turns off, then turn
the power switch to the OFF position. Unplug the
heater from the socket.
SETTING THE THERMOSTAT
1. Set the desired heat setting by pressing the mode
button
2. Press the thermostat/timer button (M) once to activate
the thermostat setting. The room temperature and a
thermostat icon flash on the display
3. Press the + or - adjuster buttons (N) to select the
desired temperature
4. The thermostat symbol will stop flashing. The
thermostat control will now automatically maintain the
preset temperature level by turning the heater on and
off.
5. To deactivate the thermostat setting, press the
thermostat/timer button continuously until the
thermostat button does not appear on the display
Note: The power light will remain lit during operation.
Note: It is normal for the heater to cycle ON and OFF as is
maintains the preset temperature.
USING THE TIMER
Programmable Timer
The user can programme the heater to turn OFF after a
selected period or to come ON at a pre-set time.
Setting the OFF timer
1. Select the mode and temperature you want the heater
to run at
2. Press the thermostat/timer button 3 times. The OFF
timer icon flashes
3. Using either the (+) or (-) adjuster buttons, programme
the heater to turn off up to 24 hours later, in increments
of 1.
4. After setting the time, the digital display will stop flashing
to show the timer is activated. The timer will count
down until the predetermined length of time has
passed, and the heater will then automatically switch
off.
Setting the ON timer
1. If the heater is on, press the thermostat/timer control
button 4 times. The ON timer icon flashes
2. Using either the (+) or (-) adjuster buttons, programme
the heater to switch on up to 24 hours later, in
increments of 1 hour.
3. After setting the ON timer, the digital display will stop
flashing to show the timer is activated. The timer will
count down until the predetermined period has passed,
and then the heater will automatically switch on.
NOTE: When the ON timer is set, the unit will remember
the setting the unit was previously on and activate to
this setting after predetermined period. The heat setting
may be changed after setting the timer by pressing the
mode button.
The default setting on the digital display is degrees Celsius
(C). To switch to degrees Fahrenheit (F) press the F-C
button.
NOTE: Do not use the handle to lift the product.
FROSTPROTECT™ MODE
When the heater is in FrostProtect™ mode, the temperature
will be maintained at 5˚C. If the room temperature is
below 5˚C the heater will automatically operate on high
setting and keep the temperature at approximately 5˚C.
To activate - press the mode button to turn the unit on,
then press the thermostat/timer button twice. The
icon will display that FrostProtect™ is activated.
ENERGY SAVINGS HEAT & SAVE™ MODE
To activate, press the mode button until (EC) appears
on the display. The heater will operate on a cycle - 10
minutes on High (1500W) and 30 minutes on Medium
(900W). When the temperature is at or above 30˚C, the
heater will ignore the 10 minute High setting and
operate on Medium for 30 minutes immediately. The
cycle repeats while in this mode.
CLEANING/MAINTENANCE
During Season Care:
1. Always unplug the heater before cleaning.
2. Clean the unit with a soft cloth moistened with a mild
soap solution.
3. NEVER use abrasive or flammable solvents to clean the
unit.
4. After cleaning, be sure to completely dry the unit with a
cloth or towel.
After Season Care:
1. Before storing, make sure to turn the heater off and
unplug the heater from the outlet. Allow the heater to
cool down completely, wrap the power cord around
the external cord wrap and store heater in a cool, dry
location.
2. The manufacturer recommends that you store the unit
in its original carton.
*TIP: Over time, dust may accumulate on the fins. This
can be removed by wiping the unit with a damp cloth.
Always unplug unit and allow to cool prior to cleaning.
TROUBLESHOOTING
If your heater fails to operate:
• UNPLUG THE UNIT
• Make sure the electrical outlet or circuit breaker is
working.
• The temperature may be set too low. Adjust the
thermostat until the heater restarts.
Please DO NOT attempt to open or repair the heater.
Please see the Warranty for Service Instructions.
If you have any questions regarding your product or
would like to learn more about other Bionaire® products,
please contact our Consumer Service Department at
1-800-253-2764 or visit our website at www.bionaire.com.
1 YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden
Consumer Solutions or if in Canada, Sunbeam
Corporation (Canada) Limited doing business as Jarden
Consumer Solutions (collectively “JCS”) warrants that for a
period of one year from the date of purchase, this product
will be free from defects in material and workmanship.
JCS, at its option, will repair or replace this product or any
component of the product found to be defective during the
warranty period. Replacement will be made with a new or
remanufactured product or component. If the product is
no longer available, replacement may be made with a
similar product of equal or greater value. This is your
exclusive warranty. Do NOT attempt to repair or adjust any
electrical or mechanical functions on this product. Doing
so will void this warranty.
This warranty is valid for the original retail purchaser from the
date of initial retail purchase and is not transferable. Keep
the original sales receipt. Proof of purchase is required to
obtain warranty performance. JCS dealers, service centers,
or retail stores selling JCS products do not have the right to
alter, modify or any way change the terms and conditions of
this warranty.
This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or
misuse of the product, use on improper voltage or current,
use contrary to the operating instructions, disassembly, repair
or alteration by anyone other than JCS or an authorized JCS
service center. Further, the warranty does not cover: Acts of
God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential
damages caused by the breach of any express, implied or
statutory warranty or condition.
Except to the extent prohibited by applicable law, any
implied warranty or condition of merchantability or fitness
for a particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use
the product including incidental, special, consequential or
similar damages or loss of profits, or for any breach of
contract, fundamental or otherwise, or for any claim
brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts,
so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may
also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any question regarding this warranty or would
like to obtain warranty service, please call 1-800-253-2764
and a convenient service center address will be provided
to you.
In Canada
If you have any question regarding this warranty or would
like to obtain warranty service, please call 1-800-253-2764
and a convenient service center address will be provided
to you.
In the U.S.A., this warranty is offered by Sunbeam
Products, Inc. doing business Jarden Consumer Solutions
located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited
doing business as Jarden Consumer Solutions, located at
20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you
have any other problem or claim in connection with this
product, please write our Consumer Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY
OF THESE ADDRESSES OR TO THE PLACE OF
PURCHASE.
© 2010 Sunbeam Products, Inc. doing business as
Jarden Consumer Solutions. All rights reserved. Imported
and distributed by Sunbeam Corporation (Canada)
Limited doing business as Jarden Consumer Solutions,
20B Hereford Street, Brampton, Ontario L6Y 0M1.
Printed in China
PN. 140467
GCDS-BIO17985-PH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement