User`s Manual
IP Kamera 9070CS-PoE
User Manual
Release Date: 10/20/2009
Manual Version: 1.3
- 1Ref#90020326K0709
Warning: Any changes made to this equipment without permission may cause damages to the
device!
IMPORTANT NOTICE
1. IP Kamera 9070-CS was designed for indoor use, the manufacturer responsibility for possible
damages caused by outdoor use, especially in the rain.
2. Please use the power adapter provided by the dealer, the manufacturer responsibility for the
possible damage from using power adapters not .
3. Do not shake the IP Kamera 9070-CS in any fashion
4. Please contact the dealer If IP Kamera 9070-CS is not working properly.
Copyright © 2008 All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.
- 2Ref#90020326K0709
Table of Content
1.) WELCOME ........................................................................................................................... 6 INTRODUCTION ............................................................................................................................ 6 MINIMUM SYSTEM REQUIREMENTS ................................................................................................. 7 2.) PRODUCT OVERVIEW .......................................................................................................... 7 FEATURES ................................................................................................................................... 7 SPECIFICATION ............................................................................................................................ 7 PACKAGE CONTENTS ..................................................................................................................... 8 LENS SPECIFICATIONS ............................................................................................................................ 8 3.) INTERFACE DESCRIPTION .................................................................................................... 9 REAR PANEL VIEW ....................................................................................................................... 9 4.) HARDWARE SETUP ............................................................................................................ 10 POE ROUTER TYPE ..................................................................................................................... 10 INTERNET ACCESSIBLE SETUP ........................................................................................................ 10 THE NETWORK USES A ROUTER/FIREWALL TO CONNECT EACH DEVICE TO THE INTERNET ................................. 11 BY USING STATIC IP ADDRESS PROVIDED BY THE ISP. ................................................................................ 11 CS LENS ................................................................................................................................... 12 CONNECTING THE DEVICE ............................................................................................................ 12 SD CARD .................................................................................................................................. 12 5.) SOFTWARE SETUP ............................................................................................................. 12 SOFTWARE FOR IP KAMERA9070‐CS POE ...................................................................................... 12 SOFTWARE FOR IP KAMERA 9070 ................................................................................................. 12 INSTALLING VLC CODEC .............................................................................................................. 14 USING IP EDIT ........................................................................................................................... 14 QUICK EASY SETUP (RECOMMENDED) ................................................................................................... 15 CUSTOM SETUP (ADVANCE USERS) ....................................................................................................... 16 IP SERVICE ............................................................................................................................... 19 6.) WEB INTERFACE ................................................................................................................ 20 CONNECTING TO THE 9070‐CS ..................................................................................................... 20 - 3Ref#90020326K0709
THE CONTROL CONSOLE .............................................................................................................. 22 LIVE VIDEO ............................................................................................................................... 23 TYPE AND ZOOM ................................................................................................................................ 23 MOTION DETECTION .......................................................................................................................... 24 ACTIVE RECORD ................................................................................................................................. 24 RECORD ........................................................................................................................................... 24 SNAPSHOT ........................................................................................................................................ 25 IMAGE ..................................................................................................................................... 25 AUDIO.............................................................................................................................................. 26 IMAGE ..................................................................................................................................... 26 IMAGE SETTINGS ................................................................................................................................ 26 TUNE IMAGE ..................................................................................................................................... 28 NETWORK ................................................................................................................................ 29 NETWORK ......................................................................................................................................... 29 FTP ................................................................................................................................................. 30 SMTP (OUTGOING E‐MAIL SERVER) ..................................................................................................... 30 SNTP .............................................................................................................................................. 31 IP SERVICE ........................................................................................................................................ 31 SYSTEM ................................................................................................................................... 32 DATE AND TIME ................................................................................................................................. 32 TIME STAMP ..................................................................................................................................... 32 USER ............................................................................................................................................... 33 AUDIO.............................................................................................................................................. 33 LANGUAGE ........................................................................................................................................ 33 UPDATE ............................................................................................................................................ 34 EVENT LOG ....................................................................................................................................... 37 APPLICATION ............................................................................................................................ 37 SETTING ........................................................................................................................................... 37 SCHEDULE RECORD ............................................................................................................................ 44 ALARM ............................................................................................................................................. 45 EPTZ‐SET................................................................................................................................. 47 HOW TO USE EPTZ WITH THE MOUSE.................................................................................................... 47 HOW TO ENABLE AND USE EPTZ CONTROLLER ....................................................................................... 47 7.) CONTROLLING THE DEVICE ................................................................................................ 48 CGI HTTP COMMANDS .............................................................................................................. 48 SNAPSHOT COMMAND: ...................................................................................................................... 48 CHANGE NAME: ................................................................................................................................ 48 CHANGE IP ADDRESS: ......................................................................................................................... 48 CHANGE PORT: .................................................................................................................................. 48 CHANGE SUBNET MASK: ..................................................................................................................... 48 CHANGE GATEWAY: ........................................................................................................................... 49 CHANGE DNS: .................................................................................................................................. 49 MJPEG STREAMING ........................................................................................................................... 49 8.) USING RTSP WITH VLC ...................................................................................................... 49 - 4Ref#90020326K0709
9.) USING CNT WITH SURF16 CH ............................................................................................ 52 FINDING THE MAC ADDRESS ........................................................................................................ 52 ADD DEVICE USING CNT .............................................................................................................. 52 10.) FREQUENTLY ASKED QUESTIONS (F.A.Q) ......................................................................... 53 - 5Ref#90020326K0709
1.) Welcome
Introduction
The IP Kamera9070-CS PoE provides reliable, high quality solution to IP Kameras. Its distinctive 720P HD
quality picture, Tri-mode video capability, SD memory storage, RTSP broadcasting capability, internal
microphone and many more functions makes this small device very powerful and unique. Using innovative
IP technology, the built in web server of the IP Kamera9070-CS PoE will allow you to view your IP Kamera
from any remote locations around the world while bringing you world class surveillance and ease of mind.
Furthermore, with CNT technology the9070-CS PoE is easy to setup & use, simply just plug and play.
- 6Ref#90020326K0709
Minimum System Requirements
CPU Minimum Requirements
•
•
•
•
•
•
•
•
•
Intel(R), Pentium(R), DUAL Core (D),CPU 3.0GHz or equivalent
Operating Systems: WINDOWS Operating Systems (IE5.0+SPI)
512 MB system memory or above
Video Card: 3D hardware accelerator card required – 100% DirectX 9.0c compatible
10/100 Ethernet switch/hub
Sound Card: DirectX 9.0c compatible sound card
Ethernet network port/card
Network cable
Internet (For remote access) or Ethernet Network (Internal Network use) with some type of Internet
connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)
Software
•
•
•
VLC media player 0.8.6b or above.
Windows XP Service Pack 2 or above.
Resolution of screen setting: 1280x960 or higher for the display of 720P
2.) Product Overview
Features
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Compatible with all standard 1/3” CS lens
Tri-Mode Camera (MPG4-1/MPEG4-2/M-Jpeg )
Advance Motion detection trigger AVI /Jpeg save on FTP / SD card or Email
3 layers (Admin, Operator, and User) Password protected
Resolution from CIF 352x192 up to HD 1280x720P
Supports NTP protocol to get correct time schedule.
1/2.5” Advance CMOS sensor, with highly sensibility for quick response insufficient lighting.
Supports HTTP CGI command set. Easy for system integration
IP Service Search utility, to find your IP Kamera on internet with ease
Watchdog / Event log design
Adjustable frame-rate, bit-rate, rate-control type, quality factor for best image quality and speed.
Supports date and time marking on the captured video, and also inserted streamed data.
Measured End-to-End latency is less than 150ms
Supports adjustable backlight, brightness, contrast, saturation & sharpness
TV Output capabilities
Automatic alarm recording buffer
CNT Technology – Just Plug and Play no need to port forward
EPTZ – Electronic Pan, Tilt, and Zoom
2 GB SD Memory Storage – Add convenience and storage
Scheduler recording capabilities
Email Capabilities
Alarm Recording Buffer
Supports: HTTP Web Server (HTTP), SSL, FTP client, SMTP client, NTP client, DHCP client,
UPnP client, RTSP over UDP, RTP
Specification
Casing: Reinforced Aluminum
Case Color: Metallic Silver Purple
Weight: 363.7 g
Dimensions (W x L x H): 5.5cm x 16cm x 5cm
Operating Conditions: 5 – 50 °C (41 – 122 °F)
Storage Conditions: Humidity 20 – 80% RH
Power: AC Adaptor
Input: 100-240V~0.3A MAX 10-20VA, 50-60Hz
Output: +12V ! 1.0A Max 5W
- 7Ref#90020326K0709
Package Contents
1.)9070-CS PoE Unit x 1 ( Without Lens )
2.) CS Lens
Lens Specifications
1.) Format: 1/3”
2.) EFFL: 6MM
3.) Image Space F/#: F1.2
4.) Field Angle: 58 degree
5.) Stop: Fixed
6.) Focus Extension: 20cm--∞
7.) Mount; CS
8.) Outside dimensions:
30 x 31.7
3.)9070-CS PoE Installation CD
4.) AC Adaptor
(One AC adaptor will be included and will correspond
to the countries power standards)
Specs:
Input: 100-250Vac /47-63Hz, 1A
Output: 12Vdc/1A Max: 12W
5.) RJ45 Cable x 1 (Optional)
6.) 2 GBSD Card
7.) Camera Mounting Bracket
- 8Ref#90020326K0709
3.) Interface Description
Rear Panel View
Rear View
SD Card
The IP Kamera9070-CS PoE comes with a 512 MB
SD Card
Reset Button:
Reset to Manufacturer Default:
Hold Reset button for 5-10 Seconds and the device
will reset to manufacturer default
Video Out:
The Video out requires a BNC connector to output
video to a different source.
RJ45 Ethernet:
Plug in the RJ45 Ethernet cable to the Ethernet port
DC 12 V Power Input:
Plug in the Power Adapter to the DC 12V
- 9Ref#90020326K0709
4.) Hardware Setup
*Before setup the device make sure of the following:
1.) Make sure that all the package contents are all included
if anything is missing please contact the store or your distributor.
2.) Make sure the power adaptor is the correct specification.
3.) Make sure that all the cables are working correctly
PoE Router Type
The 9070CS-PoE can use all standards of PoE Routers.
Option 1:
Power can be sourced from the PSE through spare lines in the CAT-5 cable
Option 2:
Power can be sourced from the PSE through the data lines via data transformer center
taps
Please view the pictures below for reference.
Internet Accessible Setup
The internet connection can be setup in two main ways so that the 9070-IR can be accessed
through the internet
- 10Ref#90020326K0709
The network uses a Router/Firewall to connect each device to the internet
In this case, the 9070-IR will need to be port forwarded on the router so that it can accessed by
the internet.
For example
9070-IR IP Address: 192.168.1.882
9070-IR Port: 9070
On the router that is being used port forwarded (port triggered) IP Address 192.168.1.882 and
port 9070. For this section you may be required to refer the user manual for the router due to the
fact that each router has a different way of setting up the device.
Note: Please refer to page: 43 on how to use CNT (Cross Network Technology). With CNT no
port forwarding is required to view the camera. But for normal functionality please use the web
browser to view the camera.
By using static IP Address provided by the ISP.
- 11Ref#90020326K0709
In this case, the 9070-IR is being connected to the internet through a hub, which is different from
a router. The hub does not provide DHCP, and therefore would require that this setup have a
static IP Address that is provided by the ISP.
Contact the ISP to find out the static IP address so that your device can be accessed through the
internet. Once a Static IP has been assigned the device will be able to automatically go onto the
internet. .
CS Lens
1.)
2.)
3.)
4.)
Carefully remove the lens from the box and the IP Kamera9070-CS PoE.
Remove the cap from the IP Kamera9070-CS PoE.
Remove the back cap from the lens
Then slowly screw in the lens to the IP Kamera9070-CS PoE in a clockwise direction to
tighten.
5.) Finally Remove the front lens cap.
6.) Loosen the lens focus screw and adjust the lens to your own liking. Turn the screw
counterclockwise to loosen and clockwise to tighten the focus
7.) Adjust the lens to your own special requirements.
Connecting the Device
1.) Connect the IP Kamera 9070 to a HUB or Router with a RJ45 network cable.
2.) Connect the HUB or Router to the internet (May through ADSL/XDSL modem).
3.) Connect the power adapter to the DC 12V port of IP Kamera 9070.
SD Card
Simply place the SD card in the back of the9070-CS PoE with the face of the SD card facing down.
5.) Software Setup
The software for the device is located on the Media Link-IP Family CD that came with the device.
IP Kamera Pack is located on the main page of the CD. Please follow the directions carefully and
install the necessary files
Software for IP Kamera9070-CS PoE
Software for IP Kamera 9070
1.) First place the Media Link-IP Family CD that came with your device into your CD/DVD Rom drive.
The CD should auto run but if it does not go to the CD/DVD Rom drive and select the file
“autorun.html”.
- 12Ref#90020326K0709
2.) Select the IP Kamera section and pick the IP Kamera and Model that you are using.
3.) Download the following software and save them to the appropriate locations.
a.
IPEdit - Device search tool which allows you to modify IP settings, find your on the local
network and IP Service.
- 13Ref#90020326K0709
b. Surf 16 CH – 16 Channel DVR, Monitoring, & Recording Software. Views up to 16
channels on one screen.
4.) Once installation is complete please double click the IPEdit to configure and search for your device.
Installing VLC Codec
The files that are recorded by the9070-CS PoE requires this codec so that you are able to view the view.
Download the latest version of the VLC codec and install it into your computer. You can find the latest
version of the codec from here
http://www.videolan.org/
Using IP Edit
IPEdit is a search tool designed to setup and access the IP Kamera9070-CS PoE.
IP Service is an additional feature which searches for the device easily without having to remember long
complicated IP addresses. Instead, this technology allows the user find his or her device through the internet
just by device name.
Note: Please allow the IP Kamera9070-CS PoE 1 to load before using IPEdit.
Default IP: 192.168.1.168 (When 9070 is connected to PC directly)
Default Login: Admin
Default Password: 12345678
1.) Double click on the IPEdit icon to run the program.
- 14Ref#90020326K0709
2.) Open IPEdit and any device in the same network should automatically be detected and listed in the
local devices sections.
Note: If the device is not showing up, please hit the rescan button and wait about 1 minute
Setup the Device:
All devices will need to be on the same network if not the device cannot be accessed and will not be
detected.
Quick Easy Setup (Recommended)
1.) Click on the REF button,
and wait a few seconds. IPEdit will automatically
detect the network settings and setup the device.
2.) Once settings have been detected hit the apply button to apply the new settings.
3.) Hit yes to confirm and Enter the login and password for the Device to Approve changes
- 15Ref#90020326K0709
4.) Then hit the rescan button on IPEdit to confirm the changes have been made.
Custom Setup (Advance Users)
1.) Highlight the device on the local devices section and on the right side of IPEdit all network
information on the device will be displayed.
If the device is not on the same network a Red Exclamation mark
Network information section
will appear in the IP
2.) To setup the device, you will need type in the correct Gateway and IP Address.
The Gateway Address: The gateway address can be obtained in Windows under the network
connections page
- 16Ref#90020326K0709
IP Address: Make sure the first 3 sections of the IP Address matches the gateway address.
Example: Gateway Address – 192.168.1.1
IP Address – 192.168.1.xxx
3.) Once the Default Gateway information has been obtained, enter the correct information
into IPEdit and hit the submit button.
4.) Then hit the rescan button on IPEdit to confirm the changes have been made.
- 17Ref#90020326K0709
- 18Ref#90020326K0709
IP Service
How to use IP Service on IPEdit:
IP service allows the user to directly connect to his / her device through the internet without having to
remember long confusing IP Address. Instead you only need to remember the name of the device that the
you have selected. Then the user can connect to IP Service, type in the device name, and connect directly
to the device.
Note: The IP Kamera9070-CS PoE requires you to select Server 2 on IP Service
1.) Open IPEdit, the device will show up in the Local Device Section. If you have not selected a name
for the device, please refer to the section on the manual labeled: “Naming your device”.
2.) To start IP Service, Hit the green connect button on the top of IPEdit.
3.) Once you have been connected search for your device by typing in at least the first 3 letters that you
named your device with. Then hit the search button.
4.) Double click on your device and an Internet Explorer window will appear connecting directly to your
device.
Note: It is crucial to have the IP Address of the device port forwarded from the router that you are using
so you can connect to your device from anywhere. Please refer to your routers user manual on how
to port forward your device.
- 19Ref#90020326K0709
6.) Web Interface
Connecting to the 9070-CS
Once the9070-CS PoE has been setup correctly and access your IP Kamera9070-CS PoE.
An Internet Explorer browser screen pop up with the login screen.
Default IP: 192.168.1.168 (When 9070 is connected to PC directly)
Default Login: Admin
Default Password: 12345678
1.) After you have logged into the device you will be required to install active x controls. If this screen
does not appear make sure you allow active x.
2.) Right click on yellow bar and install the activeX controls.
- 20Ref#90020326K0709
3.) Then click the install button and install the active controls.
4.) Once activeX controls have been installed the video feed will show on the screen
Note: If there is no active x controls that are showing up, please go to internet explorer and enable
activeX controls.
- 21Ref#90020326K0709
The Control Console
Section of the webpage. In this
The IP Kamera9070-CS PoE Control Console starts in the
section navigate to the other options and settings of the9070-CS PoE
Live Video: The Live Video section allows the user to view the camera, change resolution views,
Image: The Image section allows you to edit the image settings, including recording / viewing codec, frame
rate, image tuning, brightness, contrast, saturation, and etc.
- 22Ref#90020326K0709
Network: The network section allows you to change the devices network settings, ftp settings, smtp (email)
settings, sntp settings, and IP service settings.
System: The system section allows you to change the devices date and time, set time stamp for video,
users, audio settings, update, event log.
Application: The application section allows you to change the video recording format, ftp storage settings,
SD Card settings,
EPTZ-Set: The EPTZ allows you to zoom into the cameras image using digital zoom with pan & tilt.
Media Player: The Media player can directly access the files in the built in memory. Each video file & picture
can be accessed here and streamed through the internet.
Live Video
The Live video section of the IP Kamera 9070 is where you will live view the video of the device. From here
you can change resolution, record onto current pc, take a snapshot, zoom, and detect motion detection.
Type and Zoom
Type: The type function allows you to set the streaming format for the IP Kamera 9070. You can select from
the following type of resolutions depending on the format type you have set in the image settings.
M-JPEG (640x 352)
MPEG4-1 (1280x720)
MPEG4-2 (352x192)
Zoom: The zoom function allows you to select the screen size of the stream. Depending on the type that
you have selected there will be different zooms that will be available.
1X zoom: The 1X zoom is the normal view for each type.
- 23Ref#90020326K0709
2X zoom: This 2X zoom is 2 times the normal view for that type.
Scaled 720: Is a resolution only available in MPEG-4-1, which sets the picture at 720P.
Screen Size: Will enlarge the image to the who size of the screen. This function is very useful when trying to
display on larger monitors.
Motion Detection
Motion Detection: The motion detection icon will display when motion has been detected. This setting must
be activated in the application section
When no motion is detected the motion detection icons will look like the following.
But, in the case that motion is detected and recording has started, the icon will look will light up blue.
Active Record
Active Record: Active record will show up when the device is actively recording. Active recording functions
like motion detection, scheduler, or an alarm will set off this automatic recording.
When active recording is not activated it will look like the picture below
When the active recording function is activated it will light up in red.
Record
Record: The record button on the9070-CS PoE when pressed will record the live video feed and save the
video into the computer viewing.
To record follow the following steps:
1.) Click on the record button
2.) Then select the folder that you would like to store the file. Then hit okay.
- 24Ref#90020326K0709
3.) Once the folder has been selected the device will start to record.
To stop recording click on the red icon and it will return to the original state.
Note: Remember you need VLC codec to play the video files that are recorded
Snapshot
Snapshot: The snapshot function, creates a easy way take pictures of the current view in the IP
Kamera9070-CS PoE.
To setup the snapshot destination folder:
1.) Click on the Application link on the bottom menu
2.) Then select Snapshot path
3.) In here browse for the location where snapshot pictures will be stored. By default the snapshot path
will be in C:/
To use the snapshot function:
1.) Click on the snapshot button
2.) In explorer go to the selected path and the files will be created there.
Image
The image section allows you to change the Image settings for the device and tune the image of
the IP Kamera 9070
- 25Ref#90020326K0709
Audio
Audio: The audio function allows you to hear the sounds coming from the IP Kamera 9070’s built in
microphone.
To turn on the audio function:
1.) Click on the Audio button
2.) Then the audio button will start to move showing that sound is being transferred
3.) To turn off the audio click on the button again.
Note: Audio can only be enabled in Mpeg Mode.
Image
The image section allows you to change the Image settings for the device and tune the image of
the IP Kamera9070-CS PoE
Image Settings
The Image settings section allows you to change the video settings and the Name of the Kamera.
Camera Name: Select a camera name for the device and then hit submit
\
Video Codec:
- 26Ref#90020326K0709
Resolution:
Resolution
(MPEG4+MPEG4+JPEG):
M4:720P,M4:CIF,JPG:352
(MPEG4+JPEG):
M4:VGA,JPEG:VGA
(MPEG4+JPEG):
M4:720,JPEG:352
(MEG4+MPEG4):
M4:720,M4:CIF
(Single MPEG4):
M4:720
Color System: Select the broadcasting color system that pertains to your country.
NTSC/60Hz
PAL/50Hz
Rate Control: Select the Bit Rate Control that fits your needs.
CVBR: Constrained Variable Bit Rate
CBR: Constant Bit Rate
M-JPEG Settings: The available Quality settings and FPS for the M-JPEG settings are shown below
M-JPEG Quality Settings
High
Medium
Low
M-JPEG Frame Rate Settings
30 FPS
15 FPS
MPEG4-1
Bit Rate: Select a value from 64~8000.
FPS: Select a FPS from 30fps, 15fps, or 7.5fps
7.5 FPS
3 FPS
1 FPS
MPEG4-2
Bit Rate: Select a value from 64~8000.
FPS: Select a FPS from 15fps or 7.5fps
Enable EPTZ: The EPTZ on the IP Kamera 9070 a virtual EPTZ function. This function allows the
user to control the video on the Live Video mode by moving left or right, zooming in and zooming
out.
To use the EPTZ mode:
1.) Enable the EPTZ function and then hit the submit button.
2.) Click on Live Video Mode
3.) Click on EPTZ-Set and a new control window will pop out.
- 27Ref#90020326K0709
From here you can control the live videos Zoom Function and direction.
Also once EPTZ is enabled, in the Live View Screen buttons will appear on the bottom for you to
pan, tilt, and zoom.
Note: PTZ is only available in the mode below. When you enable PTZ it will automatically
jump into that mode.
Tune Image
The tune image settings section allows you to control and tune the picture quality of the image. Keep in mind,
the quality of the picture will also be affected by the quality of the lens that is being used.
White Balance: Select from the following options auto, indoor, or outdoor
Day and Night: Select the mode Day or Night
TV Output: Select the mode enable or disable to output to a T.V
Binning / Skipping mode: Binning enables low light-light performance. Select Binning, Skipping, 4x Binning
mode (default is Binning)
BLC (Backlight control): Select from one of the options on or off to control the
Backlight: Select a value between (0~255)
Brightness: Select a value between (0~255)
Contrast: Select a value between (0~255)
Saturation: Select a value between (0~255)
- 28Ref#90020326K0709
Sharpness: Select a value between (0~255)
Default: To Return all values to normal default click on this button.
Note: Make sure you click on the Apply button to save any changes made
Network
Network
The network section allows you to setup the network information for the IP Kamera 9070.
IP Address: Actual IP Address of the device can be found here
LAN IP Address: Local Area Network Address.
Subnet Mask: Subnet Mask information
Default Gateway: Default Gateway Address
DNS Server: Domain Name System Address
Http Port: Enter the port that you would like
MAC: The Mac Address information can be found here
Note: Make sure you click on the Apply button to save any changes made
- 29Ref#90020326K0709
FTP
The FTP section of the IP Kamera 9070 allows you to save video clips
FTP Server: Enter the FTP server address here
User Name: Enter the FTP Username
Password: Enter the FTP Password
File Upload Path: Enter the upload path of the FTP Server
SMTP (Outgoing E-mail Server)
Enter the SMTP E-mail server information here.
My Server Requires Authentication: Check this section if your email requires Server Authentication.
Account Name: Enter then login of the mail account
Password: Enter the password of the E-mail account
Use SSL Connect: If the email server requires SSL (Secure Sockets Layer) this option need
Sender Email: Enter the Sender Email Address
SMTP Server: Enter the SMTP Outgoing mail address
Email Address: Enter the Receiving Email address
- 30Ref#90020326K0709
SNTP
The SNTP is a protocol for synchronizing the clocks of computer systems.
SNTP Server: Enter the SNTP server address. Below are a list of free public NTP servers.
Europe — europe.pool.ntp.org
Asia — asia.pool.ntp.org
Oceania — oceania.pool.ntp.org
North America — north-america.pool.ntp.org
South America — south-america.pool.ntp.org
Africa — africa.pool.ntp.org
Time Zone: Enter the corresponding time zone
Automatically adjust for daylight saving time: Check this section if you want daylight saving time to be
implemented automatically.
IP Service
IP service allows you to connect to the device directly without having to remember a long IP Address. Just
enter the name of your device into IP Service and you can find your device as long as the port forwarding
has been setup.
This section allows you to turn of this service.
By default IP service is On. Click disable to close this feature.
- 31Ref#90020326K0709
System
The system section allows you to setup the IP 9070’s system configurations. This includes the following
Date and Time
Set the date and Time of the device here.
The Local Time: The local time corresponds to the current time of the IP Kamera 9070.
Time Setup: Setup the current time of the device here
1.) Set Manually: Set the time manually
2.) Synchronize with Computer Time: Synchronize the time with the current computers time
3.) Synchronize with SNTP: Synchronize with SNTP
Time Stamp
The time stamp adds a time to the live video. When a recording is made this time stamp will show up with in
the video file as well.
To enable the Time Stamp check the enable box.
- 32Ref#90020326K0709
User
The user setting allows you to create and remove users for access to the IP Kamera 9070.
Authority: Select one of the following options:
Admin: You can operate all functions in Web interface. Also,
you can add or delete any user’s account.
Operator: You can operate all functions in Web interface
except user Add/Delete.
Viewer: You can only monitor the Web interface, but cannot
operate all function and set parameters.
Audio
To enable audio recording, please select the enable button.
Language
- 33Ref#90020326K0709
The language setting section is where you can select the language that you would like to use to use the
9070. Currently there are 3 languages available: English, Chinese (Traditional), Chinese (Simplified).
The 9070 will automatically detect the favored language of choice depending the settings used in Windows.
Update
The Update Firmware section is where information on the 9070 is displayed.
The Kernel Version, Uboot Version, Firmware Version, and other technical information on the device is
displayed here.
Updating the Device
- 34Ref#90020326K0709
To update the device go to the update section. Here you will find the Current Version description.
To update the device:
1.) Browse for the correct update file.
2.) Hit the update button.
3.) A message will appear, reminding you not to disconnect when updating.
4.) Please view the bar on the bottom of internet explorer to make sure that the device is updated.
5.) When update is complete a new screen will appear then connect back to your device.
Warning: Before you go to the next step make sure you have all your setting information
written down. The device will reset back to manufacturers default values after you restart
the device. You will need reconfigure the IP Kamera 9070, including Email, FTP, IP Address,
Gateway, and etc.
6.) Enter update page, then hit the restart button.
7.) Then make sure you re-setup the device.
- 35Ref#90020326K0709
To update the device go to the update section. Here you will find the Current Version description.
To update the device:
8.) Browse for the correct update file.
9.) Hit the update button.
10.) A message will appear, reminding you not to disconnect when updating.
11.) Please view the bar on the bottom of internet explorer to make sure that the device is updated.
12.) When update is complete a new screen will appear then connect back to your device.
13.) Log back into the device go to the update page, then hit the restart button.
Warning: Before you go to the next step make sure you have all your setting information
written down. The device will reset back to manufacturer default values after you restart the
device. You will need reconfigure the IP Kamera9070-CS PoE, including Email, FTP, IP
Address, Gateway, and etc.
- 36Ref#90020326K0709
Event Log
Application
The Application Section allows you to setup the Video File information, FTP, SD Card, SMTP
Setting
Snapshot Path
The Snapshot path is the location where the snapshot pictures will be saved onto your computer. The
default snapshot path will be set to C:\. To select the snapshot path click on the
button and select the folder where the snapshots will be saved.
- 37Ref#90020326K0709
Video File
Select the Video File format that the device will record in.
1.) Avi Duration:
From the drop-down list, select the length of an AVI file.
2.) Avi Format:
MPEG4(720)
MPEG4(CIF)
3.) Hit the submit button to confirm new settings.
FTP
In the FTP section, you can set the file format that you would like to use for FTP transfer.
Note:
1.) Before you use the FTP function, you will need to set the FTP server information. You can
click on the
link to take you to the FTP setup section.
2.) If the SD Card is inserted into the device, the 9070 will only be able to record in M-Jpeg mode
to the FTP.
- 38Ref#90020326K0709
SD Card
File Format: Select the video format that you would like to save into the SD card
Split Filename Type: Select the format that you would like to save the files in the SD card. You can pick
from:
Name by Index: Creates file names according to index.
Name by Time: Creates file names according to time.
Split File Size: Select the size of each file that will be saved into the SD.
You can select from:
None, 10mb, 25mb, 50mb, & 100mb.
Enable Auto Overwrite: Auto Overwrite allows the device to automatically replace the oldest file on the SD
card when it is full.
SD Format: SD format will format the entire SD card
SD Unmount: Click the SD unmount button when the SD card is being removed this will safely remove the
card without any damages.
E-mail SMTP
In the settings section, you can find the SMTP information by clicking on the SMTP tab.
Here you can see the current SMTP Server information and email address.
Storage Settings
You can also select the file format in which you would like the IP Kamera9070-CS PoE to send.
Select from MPEG4 or MJPEG.
- 39Ref#90020326K0709
EZ-Blog
EZ Blog allows you to easily integrate code into your blog which will let you directly
stream into your blog, website, and any compatible site. This way you can IP Kamera as
more than a regular security camera but also a promotional tool.
User List: This shows the Users Available to create an Ez Blog link with. Use a guest
user account to create the EZ-Blog. You can easily create on by clicking on the User link
Setup the Embed Code
Next step is to setup the Embed Code that will be implemented into your blog, website, etc.
1.) type in the correct password for your login account.
2.) Then select the size that you would like the embedded video to be.
3.) Click on the create code button.
- 40Ref#90020326K0709
4.) You can highlight the embed code from inside the box and then copying (ctrl + C) or you can just hit
the copy button to copy the code.
5.) Once the code has been copied, place that code somewhere in the body of your blog or website
and a video will be displayed on the screen.
Media Player
The media player allows you to view your recordings on the SD card directly through the
internet without requiring downloading the file first. This feature makes it very
convenient for live streaming.
View in Full Screen
To view the IP Kamera in full screen model you will need to press the Full Screen mode.
- 41Ref#90020326K0709
My Web
The My-Web functionality will make your IP Kamera more than just a surveillance tool.
Now you can use it to promote your company, restaurant, business, school, and etc. With
some basic website skills or tools any can make a My Web site.
Turning On My Web
- 42Ref#90020326K0709
Enable my web button:
The enable My Web button will activate the My Web functionality. Once enabled every
time the device is accessed it will be set to the My Web Page.
Login Required:
The login required will require your My Web users to login to the device before being
able to use it. This is a way to keep unwanted viewers from entering the My Web
Setting up My Web
To setup My Web you can download the MyWeb file from the 9070.
1.) Click on the Download Default Page.
2.) Save the Zip file to a location where you can edit it
3.) Extract the file functions.js
4.) Start creating a My Web and be sure to include the functions.js into your code.
(Note: Do not include folders within the webpage.
5.) After you have created the webpage, make sure to create a Zip file. Zip up the file
and
Returning to default My Web page
If you would like to return your 9070 to the default My Web page click the default My
Web Page button. This will reset the current My Web to the original manufacturer default.
Using My Web
To use the My Web feature:
1.) Use IPEdit and directly log into the IP camera.
2.) The device will open the root page of the 9070 to the My Web page.
- 43Ref#90020326K0709
3.) If you would like to return to the normal administrator page for the 9070 you can
login to the admin site.
For Example:
9070 IP Address: 192.168.12.111 Port:8080
Then on the web browser type in the following
http://192.168.12.111:8080/index.htm
Schedule Record
Schedule
The schedule allows you to select days and times that you would like to schedule automatic recording. You
can pick a day from (Sunday – Saturday) and also a option for Everyday.
To schedule automatic recording:
1.) Select the day that you would want to start recording.
2.) Select the From time and the To time.
3.) Once the schedule has been created hit the submit button to apply the new settings.
Schedule Record
Schedule Record allows you to select where the schedule will record the video files to.
Schedule Record – Upload Via FTP: Saves schedule recordings into FTP
Schedule Record – Save into SD Card: Saves schedule recordings into SD Card
- 44Ref#90020326K0709
Alarm
Enable Alarm
Enable Alarm – Lost Ethernet Connection: Save into
SD Card:
When Ethernet connection is lost the device will automatically save into the SD card. Saving a backup.
FTP
Enable Alarm - Upload
When motion is detected, the IP Kamera 9070 will upload the video file to the selected FTP server.
Enable Alarm - Save Into
SD Card
When motion is detected, the IP Kamera 9070 will upload the video file to the SD card.
SMTP
Enable Alarm – Save
When motion is detected, the IP Kamera 9070 will send the video file to in a E-mail format.
Recording Time: Set the duration of time you would like the IP Kamera9070-CS PoE to record when alarm
is set off.
Enable Alarm Recording Buffer: The alarm recording buffer allows the camera to the selected amount of
buffer time before an alarm has been detected. This allows the IP Kamera9070-CS PoE to start recording
before any incident has occurred..
- 45Ref#90020326K0709
Motion Detection
To enable motion detection:
1.) Select Enable in the motion detection option.
2.) Select the sensitivity of your choice
a. You can pick from Lowest, Low, Medium, High, Highest
b. You can also customize your own threshold from (1-99)
3.) Once you have set your settings on the window screen click on the picture where you want the
motion to be detected. Double click on the selected areas to remove the choice.
You can right click on the window screen for more options
4.) Once your settings have been set hit the submit button to save all changes.
- 46Ref#90020326K0709
EPTZ-Set
The EPTZ allows you to Pan, Tilt, & Zoom the image that you are viewing.
To activate this feature EPTZ must be enabled in the Image section of the9070-CS PoE.
Note: When EPTZ Controller is activated Video Codec mode will be switched to MPEG4 & M-Jpeg when disabled the
codec will be set on Mpeg1, Mpeg2, & M-Jpeg.
How to use EPTZ with the mouse
On the Live view Video screen the EPTZ controls are:
Zoom In: Click and Hold the left mouse in the live view then release when zoomed to preferred point
Zoom into highest: Double click left mouse
Zoom out: Click and Hold the right mouse in the live view then release when zoomed to preferred point
Zoom out to screen fit: Double click right mouse
Note: When using the mouse to zoom in the snapshot function will not take a picture of the zoomed picture
but the resolution size.
How to Enable and Use EPTZ Controller
Note: When EPTZ is activated Video Codec mode will be switched to MPEG4 & M-Jpeg when disabled the
codec will be set on Mpeg1, Mpeg2, & M-Jpeg.
Also snapshot function works only with the EPTZ controller and not when using the mouse to EPTZ.
1.) Click on the EPTZ button located on the bottom of the screen of the 9070.
2.) If the EPTZ has not been enabled you will be notified that it must be enabled.
3.) Select Enable on the EPTZ function then hit the submit button
.
Once the Speed dome controller is activated you can click on left, right, up, down, and zoom buttons to view
the picture.
Note: To use EPTZ without activating
- 47Ref#90020326K0709
7.) Controlling the Device
CGI HTTP Commands
Http commands allow you to control the device with commands. The basic commands are provided below.
There are two ways to input http commands with authorization required
Password in http:
http://login:[email protected]:port/command
Password not in http:
http://ipaddress:port/command
Note: If you use the password not in http: command you will need to enter it when the browser asks
for the password.
Snapshot Command:
The snapshot command takes a snapshot of the camera in the current view.
http://ipaddress:port/snapshot.cgi
Ex. http command:
http://192.168.100.50:85/snapshot.cgi
Change Name:
This command allows you to change the name of the IP Kamera9070-CS PoE
http://ipaddress:port/vb.htm?cameratitle=name
Ex. http command:
http://192.168.1.192/vb.htm?cameratitle=test_907011
Change IP Address:
This command allows you to change the IP Address of the IP Kamera9070-CS PoE
http://ipaddress:port/vb.htm?internetip=ipaddress
Ex. http command:
http://192.168.1.192/vb.htm?internetip=192.168.1.191
Change Port:
This command allows you to change the Port of the IP Kamera9070-CS PoE
http://ipaddress:port/vb.htm?httpport=portnumber
Ex. http command:
http://192.168.1.192/vb.htm?httpport=1025
Change Subnet Mask:
This command allows you to change the Subnet Mask of the IP Kamera9070-CS PoE
http://ipaddress:port/vb.htm?subnetmask=subnetmask
- 48Ref#90020326K0709
Ex. http command
http://192.168.1.192/vb.htm?subnetmask=255.255.0.0
Note: Default subnet mask is 255.255.0.0
Change Gateway:
This command allows you to change the gateway the IP Kamera9070-CS PoE.
http://ipaddress:port/vb.htm?gateway=gatewayaddress
Ex. http command
http://192.168.1.192/vb.htm?gateway=192.168.1.1
Change DNS:
This command allows you to change the gateway the IP Kamera9070-CS PoE.
http://ipaddress:port/vb.htm?dnsip=dnsipaddress
Ex. http command
http://192.168.1.192/vb.htm?dnsip=168.95.1.1
MJPEG Streaming
This command allows you to integrate streaming data into a software, website, or any other application.
http://ipaddress:port/ipcam/mjpeg.cgi
Ex. http command
http://192.168.1.192/ipcam/mjpeg.cgi
8.) Using RTSP with VLC
Before Setting up VLC: Make sure that the 9070-Lite is set to be the DMZ host on the
router that you are using, please refer to the routers manual on how to accomplish this.
How to setup VLC media player & Open a network stream
Note: Before using RSTP you must port forward your router to the following port numbers.
For 1280 x 720P (Mpeg4-1): Port forward to 554
If Port forwarding (Mpeg4-2): Port forward to 8554
1.) Open VLC media Player
2.) Click on Tools > Preference
3.) On the bottom of the screen click the Reset preference button.
4.) On the bottom left hand side of VLC select the all under the show settings area.
5.) Then in the left panel select Input / Codecs > Demuxers > RTP/RTSPl and type in the RTSP user
name and RTSP password.
- 49Ref#90020326K0709
6.) Check the Cache value. For low latency, it should be 70~80 based on PC’s performance.
Note: If the video is not smooth, set the caching value from 150~1200. This problem could be due to too
much congestion, busy pc, and etc.
7.) Save the new settings
8.) Then go back to the VLC media player and go to Media > Advance Open File
9.) Next select the network tab and under the protocol select RTSP.
10.) Type in the RTSP address of your device
For Mpeg4 Stream1 : rtsp://<IP Address>/mpeg4
For Mpeg4 Stream2 : rtsp://<IP Address>:8554/mpeg4
Example: rtsp://122.116.137.123/mpeg4
- 50Ref#90020326K0709
Hit the play button and wait a few seconds for the program to start streaming.
- 51Ref#90020326K0709
9.) Using CNT with Surf16 CH
CNT makes connecting to the IP Kamera 9070 a very simple task. Using Surf 16 CH and multi device DVR
monitoring software, you can easily view your 9070CS.
Follow these simple steps:
Finding the MAC Address
There are two ways to find the MAC address in IPEdit.
*Note: IP Server must be enabled on your device’s webpage. By default IP Server is enabled.
Find MAC Address in LAN Using IPEdit
1.) In IPEdit, highlight the device that you are using. On the right side of IPEdit you will find the MAC
Address that you will need to use CNT.
*Note: Make sure when you are typing in the MAC address to leave out the “:”
Find MAC Address in WAN Using IPService on IPEdit
1.) To find your MAC Address through the internet, Open IPEdit and hit the connect button on IP
Service.
2.) Then Type in the name of your device in this case it is “Sample Name”, then hit the search button.
3.) Your device should be listed and the MAC address should be displayed on the screen. Copy down
the MAC address and use it to connect via CNT.
Add device using CNT
1.) On Surf 16 Ch DVR software, right click on the screen on one of the windows and select Add
Camera
2.) Then under the section labeled MAC: Type in the MAC address.
- 52Ref#90020326K0709
3.) Do not forget to enter the password and login.
10.) Frequently Asked Questions (F.A.Q)
Q1: Why can’t I view the video files that I have recorded, nothing is playing?
Ans: VLC Codec, you can download VLC Codec from their website at:
Q2: How do I reset the device to manufacturers default values
Ans: On the back of the device there is a reset button, hold down the reset button for more than 7 seconds.
Then give the9070-CS PoE a 1 minute to restart. Once the device has restarted it will be set back to
manufacturer default settings.
Default Values
Default IP: 192.168.1.168 (When9070-CS PoE is connected to PC directly)
Default Login: Admin
Default Password: 12345678
Q3: Why does the device on EPTZ change my video mode?
Ans: When EPTZ is activated Video Codec mode will be switched to MPEG4 & M-Jpeg when disabled the
codec will be set on Mpeg1, Mpeg2, & M-Jpeg.
Q4: How do I take snapshots using the EPTZ function?
Ans: When using EPTZ function remember that only the snapshot functions works with the EPTZ controller.
If you are just using the mouse to Pan Tilt and Zoom into your picture you the snapshot button will not
capture the screen correctly. A way you can take a picture of the screen using the EPTZ with the mouse is
to click on the print screen button on your computer.
Q5: Why is the RTSP not connecting to my VLC player or Quick time Player?
Ans: To use the RTSP functionality it is necessary to first set your 9070-Lite to be the DMZ host in your
network. Also be sure to port forward your device at the following ports.
Port 554 for 1280 x 720P
Port 8554 for CIF format
Please refer to the routers manual on how this is setup
Q6: How do I improve the image quality on this device?
Ans: The Image quality of the 9070 is dependent on the bit rate of the device. With a larger bit rate the
device will naturally create higher quality image, but this will affect the smoothness of the streaming when
accessed through the internet. To find the most optimal settings for image quality and streaming
smoothness, try different bit rate settings to achieve the best fit settings. .
- 53Ref#90020326K0709
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement