OnCell G3111/G3151-HSPA Series Quick Installation Guide

OnCell G3111/G3151-HSPA Series Quick Installation Guide
3. Hardware Introduction
OnCell G3111/G3151-HSPA Series
Quick Installation Guide
First Edition, September 2013
Reset Button—Press and hold the Reset button for 5 sec to load
factory defaults: Use a pointed object, such as a straightened paper
clip or toothpick, to press the reset button. This will cause the Ready
LED to blink on and off. The factory defaults will be loaded once the
Ready LED stops blinking (after about 5 seconds). At this point, you
should release the reset button (the default IP is 192.168.127.254).
LED Indicators
The LED indicators on the front panel of the OnCell
G3111/G3151-HSPA are described in the following table.
1. Overview
The OnCell G3111/G3151-HSPA are cellular IP gateways that can
conveniently and transparently connect your devices to a 3G cellular
network, allowing you to connect to your existing Ethernet and serial
devices with only basic configuration. With the integrated
GuaranLink feature, you can be confident that your device will
always stay connected and recover from any unexpected
interference. With Moxa’s industrial design, higher EMS level are
tested to ensure the highest reliability for any harsh environment.
The G3111/G3151-HSPA cellular IP gateways are the most compact,
simple, and robust industrial 3G solution.
Type
PWR
READY
GSM/GPRS
Before Installing the OnCell G3111/G3151-HSPA series, verify that
the package contains the following items:
UMTS/HSPA
Standard Accessories
•
•
•
•
•
Document & Software CD
Omni 1.5 dBi Rubber SMA Antenna
(model name: ANT-WCDMA-ASM-1.5)
DIN-Rail Kit
3-pin Terminal Block
Rubber Stand
Product Warranty Statement
Quick Installation Guide
TX/RX
Signal
(3 LEDs)
Optional Accessories
•
Off
Green
2. Package Checklist
•
•
Color
Green
Red
(Over
Green)
Off
Green
Amber
Off
Green
Amber
Off
Green
Amber
Off
Green
LED Function
Activation of DC Power.
Power is off, or power error condition
exists.
Steady on: Software Ready.
Blinking slowly (1 sec): The OnCell has
been located by the OnCell Search Utility.
Steady on: Booting up, or IP fault.
Blinking rapidly (0.5 sec): IP conflict.
Blinking slowly (1 sec): Cannot get an IP
address from the DHCP server.
Booting up or there is no error condition.
GSM is connected.
GPRS is connected.
GSM/GPRS is disconnected.
UMTS is connected.
HSPA is connected.
UMTS/HSPA is disconnected.
The serial port is transmitting data
The serial port is receiving data.
No data is being transmitted or received
through the serial port.
Number of LEDs indicates cellular
connection signal level
(at least 2 LEDs must illuminated for data
transmission)
DIP switches on the bottom of
the OnCell G3151-HSPA are
used to set the pull high/low
resistor value for each serial
port.
2
Pull Low
1 kΩ
150 kΩ
3
Terminator
120 Ω
---
4
-------
Note: When using RS-232 mode, ALL resistors need to be set to
OFF.
4. Hardware Installation Procedure
STEP 1: Open the SIM cover, and insert the SIM card in the SIM card
slot.
STEP 2: Wire the terminal block with 12-48 VDC power (see section
6) and connect the power.
STEP 3: To configure the OnCell, use an Ethernet cable to connect
the OnCell directly to your computer’s Ethernet interface.
DIN-Rail Mounting
The OnCell G3111/G3151-HSPA series have
built-in “ears” for attaching the IP gateway to a
wall or the inside of a cabinet. We suggest using
two screws per ear to attach the IP gateway to a
wall or the inside of a cabinet. The heads of the
screws should be less than 6.0 mm in diameter,
and the shafts should be less than 3.5 mm in
diameter, as shown in the figure at the right.
5. Software Installation Information
The Document & Software CD contains the User’s Manual, OnCell
Search Utility, and OnCell Driver Manager. Insert the CD and follow
the on-screen instructions. Please refer to the User’s Manual for
additional details on using the OnCell Search Utility and Driver
Manager.
Note: Please notify your sales representative if any of the above
items are missing or damaged.
P/N: 1802031011010
ON
OFF
1
Pull High
1 kΩ
150 kΩ
Adjustable pull high/low resistor for RS-485 Port (OnCell
G3151-HSPA Only)
Five-band GSM/GPRS/EDGE/UMTS/HSPA antennas for OnCell
G3111/G3151-HSPA series (impedance = 50 ohms):
ANT-WCDMA-AHSM-04-2.5m: Omni 4dBi(peak)/11cm,
magnetic SMA five-band antenna (impedance = 50 ohms), 2.5
m
ANT-WCDMA-ANF-00: Omni 0dBi(peak)/42cm, N-type female
five-band antenna (impedance = 50 ohms)
–1–
SW
–2–
–3–
-4-
6. Pin Assignments and Cable Wiring
EDGE Data Rate
Power Input and Relay Output Pinouts
GPRS Data Rate
SIM Interface
Antenna Interface
PIN
1
2
3
Name
V+
V-
Function
DC Power Input (Positive)
DC Power Input (Negative)
GND
DB9 Male Port Pinouts
Note that the OnCell G3111-HSPA only support RS-232. The
RS-422/485 pin assignments only apply to the OnCell G3151-HSPA.
DB9 Male
OnCell G3111-HSPA (RS-232)
Pin
1
2
3
4
5
6
7
8
9
DB9 Male
RS-232
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
---
OnCell G3151-HSPA (RS-232/422/482)
Pin
1
2
3
4
5
6
7
8
9
RS-232 RS-422/485-4w RS-485-2w
DCD
TxD-(A)
--RxD
TxD+(B)
--TxD
RxD+(B)
Data+(B)
DTR
RxD-(A)
Data-(A)
GND
GND
GND
DSR
----RTS
----CTS
-----------
7. Specifications
Cellular Interface
Standards
Band Options:
HSPA Data Rate
GSM/GPRS/EDGE/UMTS/HSPA
Five-band UMTS/HSPA 850/800, 900, 1900
and 2100 MHz
Quad-band GSM/GPRS/EDGE
850/900/1800/1900 MHz
HSDPA Cat. 10 / HSUPA Cat.6
DL: max. 14.4 Mbps, UL: max. 5.76 Mbps
–5–
LAN Interface
Number of Ports
Ethernet
EDGE Class 12
DL: max. 237 kbps, UL: max. 237 kbps
GPRS Class 12
DL: max. 85.6 kbps, UL: max. 85.6 kbps
Number of SIMs: 1
SIM Control: 3 V
Number of Antenna Ports: 1
Connector: SMA (Female)
1
10/100 Mbps, RJ45 connector, Auto
MDI/MDIX
Serial Interface
Number of Ports
Serial Standards
1
G3111-HSPA: 1 RS-232 port, DB9 male
G3151-HSPA: 1 RS-232/422/485 port, DB9
male
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR,
DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Serial Operation
Operation Modes: TCP Server, TCP Client,
Modes
UDP, RFC2217
Operation Modes (Moxa Proprietary): Real
COM, Reverse Real COM, SMS Tunnel Mode
Windows Real COM Drivers: Windows
2000/XP/2003/Vista/7/Server 2008,
Windows XP/2003/Vista/7/Server 2008 x64
Fixed TTY Drivers: SCO Unix, SCO
OpenServer 5, SCO OpenServer 6, UnixWare
7, SVR4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD 5, FreeBSD 6
Serial Communication Data Bits: 5, 6, 7, 8
Parameters
Stop Bits: 1, 1.5, 2 (when parity = None)
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS, XON/XOFF
Baudrate: 50 bps to 921.6 Kbps
Physical Characteristics
Housing
Aluminum, providing IP30 protection
Weight
165±5 g
Dimensions
111 x 77 x 26 mm (4.37 x 3.03 x 1.02 in)
Environmental Limits
Operating
-30 to 55°C (-22 to 131°F)
Temperature
Storage Temperature -40 to 75°C (-40 to 167°F)
Ambient Relative
5 to 95% (30°C, non-condensing)
Humidity
Power Requirements
Input Voltage
12 to 48 VDC
Connector
3-pin removable terminal block
Power Consumption
12 to 48 VDC, 350 mA (Idle), 900 mA (max.)
Reverse Polarity
Present
Protection
Standards and Certifications
Safety
UL 60950-1
EMC
EN 55022 Class A, EN 55024, FCC Part 15
Subpart B Class A
Radio
EN 301 489-1, EN 301 489-7, EN 301 511/4
Warranty
Warranty Period
Details
5 years
See www.moxa.com/support/warranty.aspx
Software Specification
Network Protocols
ICMP, TCP/IP, UDP, DHCP, Telnet, DNS,
SNMP, HTTP, HTTPS, SMTP, SNTP, ARP
Router/Firewall
NAT, Port Forwarding
Authentication
Local user-name and password
Security
Accessible IP list
Configuration and
SNMP MIB-II, SNMP Private MIB,
Management Options SNMPv1/v2c/v3, Web/Telnet/Serial Console
Others
DDNS, Auto IP Report
Software Specification (Moxa Proprietary)
GuaranLink feature
Reliable and persistent cellular connectivity
OnCell Central
Private cellular IP communication and central
Management support device management
OnCell Search Utility Device configuration and management
www.moxa.com/support
The Americas:
Europe:
Asia-Pacific:
China:
+1-714-528-6777 (toll-free: 1-888-669-2872)
+49-89-3 70 03 99-0
+886-2-8919-1230
+86-21-5258-9955 (toll-free: 800-820-5036)
 2013 Moxa Inc. All rights reserved.
–6–
–7–
-8-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement