Apprentice II N2 Point Map

Apprentice II N2 Point Map
Appendix N: N2 Commmunications
N.1 Overview
The ILC Apprentice II controller can be integrated into a Building Automation System
(BAS) that uses the N2 communications protocol. The host system can then poll the status of the ILC Apprentice II controller inputs
and outputs and issue ON/OFF commands
to the ILC Apprentice II’s relay outputs.
N.2 Hardware Setup
The ILC Apprentice II must be equipped with
a N2 add-on module that is addressed with
a unique node address. (See Figure N-1.) The
network cable is a two wire shielded twisted
pair. Consult the BAS system documentation
for the exact specifications. Terminate the
cable as shown in Figure N-1.
N.3 Point Map
Fill out the point map for the ILC Apprentice
II controller. Note that only BI and BO point
types are used. The completed point map
will serve as the control schedule used to
determine how ILC Apprentice II relay outputs will be controlled.
ILC LightMaster N2 Rev 1 Unsupported Attributes
All attributes in the following regions
Analog Input
Analog Output
Internal Float
Internal Integer
Internal Byte
Binary Input Unsupported Attributes
Attribute 1
Bit 0
Bit 1
Bit 3
COS _enabled
Normal state
Alarm_enabled
Attribute 2
Bit 0
Bit 1
Bit 4
Bit 5
Always reliable (0)
Override active
Normal (0)
JCI use only
Attribute 3
JCI use only
Attribute 4
JCI use only
Always 1 (COS is always enabled)
Always 0
Always 0 (disabled)
Always 0 (not active)
Binary Output Unsupported Attributes
Attribute 1
Bit 0
Bit 1
COS _enabled
Normal state
Attribute 2
Bit 0
Bit 1
Bit 4
Bit 5
Always reliable (0)
Override active
JCI use only
JCI use only
Attribute 3
Minimum ON time
Always 0
Attribute 4
Minimum OFF time
Always 0
Attribute 5
Maximum Cycles/Hour
Always 0
Attribute 6
JCI use only
Attribute 7
JCI use only
ILC Apprentice II User Manual
Version 1A 9/1/06
Always 0 (COS is always enabled)
Always 0
Always 0 (not active)
N-1
Appendix N: N2 Commmunications
ILC Apprentice II N2 Network Example – See Termination Detail Below
DIP Switch Addressing
Add the value of each ON
ON
switch to determine the
address (address 02 shown).
77013466A
128
64
32
16
8
4
2
1
ILC APPRENTICE II
MON 08/07/06
04:19:44 PM
EDIT
(C) 2006 ILC
POWER
12VAC
CT
12VAC
OFF
ALL ON ALL OFF
ON
LOAD LINE
N.O.
N2 Add-On card
mounted below ILC
Apprentice controller
CPU board
1 PILOT
2 PILOT
1 ON
2 ON
1 OFF
2 OFF
1 COM
2 COM
3 PILOT
4 PILOT
3 ON
4 ON
3 OFF
4 OFF
3 COM
4 COM
LOAD LINE
N.O.
LOAD LINE
N.O.
LOAD LINE
N.O.
77013469A
ILC Apprentice II Controller
NEG
DRAIN
18 Gauge, Shielded twisted pair
77013452 REV A
97103452 REV
POS
to N2 network
N2 Add-on Card
100 ohm Terminating Resistor
(Used only if ILC Apprentice II controller
is the last device on able)
NOTE: Drain wire must only
be connected on one end.
Figure N-1 N2 Set-Up
Appendix
ILC Apprentice II User Manual
Version 1A 9/1/06
N-2
Appendix N: N2 Commmunications
N2 – Fast Track
ILC APPRENTICE II
FRI 12/01/06
07:50:54 PM
EDIT
(C)2006 ILC
Press þ EDIT, then ý 4 times
SET TIMES
PRESETS
ADD-ON MODULE
EXIT
Press þ ADD-ON MODULE
METASYS N2 REV 3
EXIT
NODE:001
N2
Screen Flow
ILC Apprentice II User Manual
Version 1A 9/1/06
N-3
Appendix N: N2 Commmunications
NETWORK
NETWORK
POINT TYPE POINT ADDRESS
UNITS
POINT DESCRIPTION
RANGE/VALUE
BI
1
SWITCH INPUT #1 OFF
0-OPEN 1-CLOSED
BI
2
SWITCH INPUT #1 ON
0-OPEN 1-CLOSED
BI
3
SWITCH INPUT #2 OFF
0-OPEN 1-CLOSED
BI
4
SWITCH INPUT #2 ON
0-OPEN 1-CLOSED
BI
5
SWITCH INPUT #3 OFF
0-OPEN 1-CLOSED
BI
6
SWITCH INPUT #3 ON
0-OPEN 1-CLOSED
BI
7
SWITCH INPUT #4 OFF
0-OPEN 1-CLOSED
BI
8
SWITCH INPUT #4 ON
0-OPEN 1-CLOSED
BI
9
SWITCH INPUT #5 OFF
0-OPEN 1-CLOSED
BI
10
SWITCH INPUT #5 ON
0-OPEN 1-CLOSED
BI
11
SWITCH INPUT #6 OFF
0-OPEN 1-CLOSED
BI
12
SWITCH INPUT #6 ON
0-OPEN 1-CLOSED
BI
13
SWITCH INPUT #7 OFF
0-OPEN 1-CLOSED
BI
14
SWITCH INPUT #7 ON
0-OPEN 1-CLOSED
BI
15
SWITCH INPUT #8 OFF
0-OPEN 1-CLOSED
BI
16
SWITCH INPUT #8 ON
0-OPEN 1-CLOSED
BI
17
SWITCH INPUT #9 OFF
0-OPEN 1-CLOSED
BI
18
SWITCH INPUT #9 ON
0-OPEN 1-CLOSED
BI
19
SWITCH INPUT #10 OFF 0-OPEN 1-CLOSED
BI
20
SWITCH INPUT #10 ON
BI
21
SWITCH INPUT #11 OFF 0-OPEN 1-CLOSED
BI
22
SWITCH INPUT #11 ON
BI
23
SWITCH INPUT #12 OFF 0-OPEN 1-CLOSED
BI
24
SWITCH INPUT #12 ON
NOTES
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
Appendix
0-OPEN 1-CLOSED
Table N.1 – ILC Apprentice II Input N2 Point Map
ILC Apprentice II User Manual
Version 1A 9/1/06
N-4
Appendix N: N2 Commmunications
NETWORK
NETWORK
POINT TYPE POINT ADDRESS
UNITS
POINT DESCRIPTION
RANGE/VALUE
BI
25
SWITCH INPUT #13 OFF 0-OPEN 1-CLOSED
BI
26
SWITCH INPUT #13 ON
BI
27
SWITCH INPUT #14 OFF 0-OPEN 1-CLOSED
BI
28
SWITCH INPUT #14 ON
BI
29
SWITCH INPUT #15 OFF 0-OPEN 1-CLOSED
BI
30
SWITCH INPUT #15 ON
BI
31
SWITCH INPUT #16 OFF 0-OPEN 1-CLOSED
BI
32
SWITCH INPUT #16 ON
BI
33
SWITCH INPUT #17 OFF 0-OPEN 1-CLOSED
BI
34
SWITCH INPUT #17 ON
BI
35
SWITCH INPUT #18 OFF 0-OPEN 1-CLOSED
BI
36
SWITCH INPUT #18 ON
BI
37
SWITCH INPUT #19 OFF 0-OPEN 1-CLOSED
BI
38
SWITCH INPUT #19 ON
BI
39
SWITCH INPUT #20 OFF 0-OPEN 1-CLOSED
BI
40
SWITCH INPUT #20 ON
BI
41
SWITCH INPUT #21 OFF 0-OPEN 1-CLOSED
BI
42
SWITCH INPUT #21 ON
BI
43
SWITCH INPUT #22 OFF 0-OPEN 1-CLOSED
BI
44
SWITCH INPUT #22 ON
BI
45
SWITCH INPUT #23 OFF 0-OPEN 1-CLOSED
BI
46
SWITCH INPUT #23 ON
BI
47
SWITCH INPUT #24 OFF 0-OPEN 1-CLOSED
BI
48
SWITCH INPUT #24 ON
BI
49
SWITCH INPUT #25 OFF 0-OPEN 1-CLOSED
NOTES
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
Table N.1 – ILC Apprentice II Input N2 Point Map
ILC Apprentice II User Manual
Version 1A 9/1/06
N-5
Appendix N: N2 Commmunications
NETWORK
NETWORK
POINT TYPE POINT ADDRESS
UNITS
POINT DESCRIPTION
RANGE/VALUE
BI
50
SWITCH INPUT #25 ON
BI
51
SWITCH INPUT #26 OFF 0-OPEN 1-CLOSED
BI
52
SWITCH INPUT #26 ON
BI
53
SWITCH INPUT #27 OFF 0-OPEN 1-CLOSED
BI
54
SWITCH INPUT #27 ON
BI
55
SWITCH INPUT #28 OFF 0-OPEN 1-CLOSED
BI
56
SWITCH INPUT #28 ON
BI
57
SWITCH INPUT #29 OFF 0-OPEN 1-CLOSED
BI
58
SWITCH INPUT #29 ON
BI
59
SWITCH INPUT #30 OFF 0-OPEN 1-CLOSED
BI
60
SWITCH INPUT #30 ON
BI
61
SWITCH INPUT #31 OFF 0-OPEN 1-CLOSED
BI
62
SWITCH INPUT #31 ON
BI
63
SWITCH INPUT #32 OFF 0-OPEN 1-CLOSED
BI
64
SWITCH INPUT #32 ON
BI
65
SWITCH INPUT #33 OFF 0-OPEN 1-CLOSED
BI
66
SWITCH INPUT #33 ON
BI
67
SWITCH INPUT #34 OFF 0-OPEN 1-CLOSED
BI
68
SWITCH INPUT #34 ON
BI
69
SWITCH INPUT #35 OFF 0-OPEN 1-CLOSED
BI
70
SWITCH INPUT #35 ON
BI
71
SWITCH INPUT #36 OFF 0-OPEN 1-CLOSED
BI
72
SWITCH INPUT #36 ON
BI
73
SWITCH INPUT #37 OFF 0-OPEN 1-CLOSED
NOTES
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
Appendix
0-OPEN 1-CLOSED
Table N.1 – ILC Apprentice II Input N2 Point Map
ILC Apprentice II User Manual
Version 1A 9/1/06
N-6
Appendix N: N2 Commmunications
NETWORK
NETWORK
POINT TYPE POINT ADDRESS
UNITS
POINT DESCRIPTION
RANGE/VALUE
BI
74
SWITCH INPUT #37 ON
BI
75
SWITCH INPUT #38 OFF 0-OPEN 1-CLOSED
BI
76
SWITCH INPUT #38 ON
BI
77
SWITCH INPUT #39 OFF 0-OPEN 1-CLOSED
BI
78
SWITCH INPUT #39 ON
BI
79
SWITCH INPUT #40 OFF 0-OPEN 1-CLOSED
BI
80
SWITCH INPUT #40 ON
BI
81
SWITCH INPUT #41 OFF 0-OPEN 1-CLOSED
BI
82
SWITCH INPUT #41 ON
BI
83
SWITCH INPUT #42 OFF 0-OPEN 1-CLOSED
BI
84
SWITCH INPUT #42 ON
BI
85
SWITCH INPUT #43 OFF 0-OPEN 1-CLOSED
BI
86
SWITCH INPUT #43 ON
BI
87
SWITCH INPUT #44 OFF 0-OPEN 1-CLOSED
BI
88
SWITCH INPUT #44 ON
BI
89
SWITCH INPUT #45 OFF 0-OPEN 1-CLOSED
BI
90
SWITCH INPUT #45 ON
BI
91
SWITCH INPUT #46 OFF 0-OPEN 1-CLOSED
BI
92
SWITCH INPUT #46 ON
BI
93
SWITCH INPUT #47 OFF 0-OPEN 1-CLOSED
BI
94
SWITCH INPUT #47 ON
BI
95
SWITCH INPUT #48 OFF 0-OPEN 1-CLOSED
BI
96
SWITCH INPUT #48 ON
NOTES
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
0-OPEN 1-CLOSED
Table N.1 – ILC Apprentice II Input N2 Point Map
ILC Apprentice II User Manual
Version 1A 9/1/06
N-7
Appendix N: N2 Commmunications
NETWORK
NETWORK
POINT TYPE POINT ADDRESS
UNITS
POINT DESCRIPTION
RANGE/VALUE
1
RELAY OUTPUT #1
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
2
RELAY OUTPUT #2
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
3
RELAY OUTPUT #3
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
4
RELAY OUTPUT #4
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
5
RELAY OUTPUT #5
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
6
RELAY OUTPUT #6
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
7
RELAY OUTPUT #7
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
8
RELAY OUTPUT #8
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
9
RELAY OUTPUT #9
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
10
RELAY OUTPUT #10
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
11
RELAY OUTPUT #11
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
12
RELAY OUTPUT #12
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
13
RELAY OUTPUT #13
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
14
RELAY OUTPUT #14
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
15
RELAY OUTPUT #15
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
16
RELAY OUTPUT #16
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
17
RELAY OUTPUT #17
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
18
RELAY OUTPUT #18
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
19
RELAY OUTPUT #19
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
20
RELAY OUTPUT #20
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
21
RELAY OUTPUT #21
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
22
RELAY OUTPUT #22
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
23
RELAY OUTPUT #23
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
24
RELAY OUTPUT #24
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
Table N.1 – ILC Apprentice II Relay Output N2 Point Map
ILC Apprentice II User Manual
Version 1A 9/1/06
N-8
Appendix
BO
Appendix N: N2 Commmunications
NETWORK
NETWORK
POINT TYPE POINT ADDRESS
UNITS
POINT DESCRIPTION
RANGE/VALUE
BO
25
RELAY OUTPUT #25
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
26
RELAY OUTPUT #26
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
27
RELAY OUTPUT #27
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
28
RELAY OUTPUT #28
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
29
RELAY OUTPUT #29
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
30
RELAY OUTPUT #30
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
31
RELAY OUTPUT #31
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
32
RELAY OUTPUT #32
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
33
RELAY OUTPUT #33
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
34
RELAY OUTPUT #34
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
35
RELAY OUTPUT #35
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
36
RELAY OUTPUT #36
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
37
RELAY OUTPUT #37
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
38
RELAY OUTPUT #38
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
39
RELAY OUTPUT #39
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
40
RELAY OUTPUT #40
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
41
RELAY OUTPUT #41
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
42
RELAY OUTPUT #42
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
43
RELAY OUTPUT #43
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
44
RELAY OUTPUT #44
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
45
RELAY OUTPUT #45
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
46
RELAY OUTPUT #46
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
47
RELAY OUTPUT #47
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
BO
48
RELAY OUTPUT #48
0-OFF (Open) 1-ON (Closed) 2-OFF w/Timer Option
Table N.1 – ILC Apprentice II Relay Output N2 Point Map
ILC Apprentice User Manual
Version 1A 9/1/06
N-9
Appendix N: N2 Commmunications
NETWORK
POINT ADDRESS
INPUTS
BO
201
01
0- Input Enable 1- Input Disable
BO
202
02
0- Input Enable 1- Input Disable
BO
2 03
03
0- Input Enable 1- Input Disable
BO
204
04
0- Input Enable 1- Input Disable
BO
205
05
0- Input Enable 1- Input Disable
BO
206
06
0- Input Enable 1- Input Disable
BO
207
07
0- Input Enable 1- Input Disable
BO
208
08
0- Input Enable 1- Input Disable
BO
209
09
0- Input Enable 1- Input Disable
BO
210
10
0- Input Enable 1- Input Disable
BO
211
11
0- Input Enable 1- Input Disable
BO
212
12
0- Input Enable 1- Input Disable
BO
213
13
0- Input Enable 1- Input Disable
BO
214
14
0- Input Enable 1- Input Disable
BO
215
15
0- Input Enable 1- Input Disable
BO
216
16
0- Input Enable 1- Input Disable
BO
217
17
0- Input Enable 1- Input Disable
BO
218
18
0- Input Enable 1- Input Disable
BO
219
19
0- Input Enable 1- Input Disable
BO
220
20
0- Input Enable 1- Input Disable
BO
221
21
0- Input Enable 1- Input Disable
BO
222
22
0- Input Enable 1- Input Disable
BO
223
23
0- Input Enable 1 -Input Disable
BO
224
24
0- Input Enable 1- Input Disable
RANGE/VALUE
NOTES
Appendix
NETWORK
POINT TYPE
Table N.1 – ILC Apprentice II Input Disable/Enable N2 Point Map
ILC Apprentice User Manual
Version 1A 9/1/06
N-10
Appendix N: N2 Commmunications
NETWORK
POINT TYPE
NETWORK
POINT ADDRESS
INPUTS
BO
225
25
0- Input Enable 1- Input Disable
BO
226
26
0- Input Enable 1- Input Disable
BO
227
27
0- Input Enable 1- Input Disable
BO
228
28
0- Input Enable 1- Input Disable
BO
229
29
0- Input Enable 1- Input Disable
BO
230
30
0- Input Enable 1- Input Disable
BO
231
31
0- Input Enable 1- Input Disable
BO
232
32
0- Input Enable 1- Input Disable
BO
233
33
0- Input Enable 1- Input Disable
BO
234
34
0- Input Enable 1- Input Disable
BO
235
35
0- Input Enable 1- Input Disable
BO
236
36
0- Input Enable 1- Input Disable
BO
237
37
0- Input Enable 1- Input Disable
BO
238
38
0- Input Enable 1- Input Disable
BO
239
39
0- Input Enable 1- Input Disable
BO
240
40
0- Input Enable 1- Input Disable
BO
241
41
0- Input Enable 1- Input Disable
BO
242
42
0- Input Enable 1- Input Disable
BO
243
43
0- Input Enable 1- Input Disable
BO
244
44
0- Input Enable 1- Input Disable
BO
245
45
0- Input Enable 1- Input Disable
BO
246
46
0- Input Enable 1- Input Disable
BO
247
47
0- Input Enable 1 -Input Disable
BO
248
48
0- Input Enable 1- Input Disable
RANGE/VALUE
NOTES
Table N.1 – ILC Apprentice II Input Disable/Enable N2 Point Map
ILC Apprentice II User Manual
Version 1A 9/1/06
N-11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement