H8S, H8SX Family E10A-USB Emulator User`s Manual

H8S, H8SX Family E10A-USB Emulator User`s Manual
User’s Manual
H8S, H8SX Family E10A-USB Emulator
User’s Manual
(HS0005KCU01H, HS0005KCU02H)
H8S, H8SX Family E10A-USB
HS0005KCU01HE-H8S
All information contained in these materials, including products and product specifications,
represents information on the product at the time of publication and is subject to change by
Renesas Electronics Corporation without notice. Please review the latest information published
by Renesas Electronics Corporation through various means, including the Renesas Electronics
Corporation website (http://www.renesas.com).
www.renesas.com
Rev. 14.00
Aug. 2012
Notice
1.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of
semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software,
and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you
or third parties arising from the use of these circuits, software, or information.
2.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics
does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages
incurred by you resulting from errors in or omissions from the information included herein.
3.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of
third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No
license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of
Renesas Electronics or others.
4.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration,
modification, copy or otherwise misappropriation of Renesas Electronics product.
5.
Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The
recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below.
“Standard”:
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual
equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc.
“High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; and safety equipment etc.
Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to
human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property
damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas
Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any
application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred
by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas
Electronics.
6.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics,
especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation
characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or
damages arising out of the use of Renesas Electronics products beyond such specified ranges.
7.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have
specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further,
Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to
guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas
Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and
malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation
of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by
you.
8.
Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility
of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and
regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive.
Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws
and regulations.
9.
Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose
manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use
Renesas Electronics products or technology described in this document for any purpose relating to military applications or use
by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas
Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise
places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this
document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of
unauthorized use of Renesas Electronics products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas
Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document
or Renesas Electronics products, or if you have any other inquiries.
(Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries.
(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.
(2012.4)
Regulatory Compliance Notices
z European Union regulatory notices
This product complies with the following EU Directives. (These directives are only valid in the European
Union.)
CE Certifications:
• Electromagnetic Compatibility (EMC) Directive 2004/108/EC
EN 55022 Class A
WARNING:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
EN 55024
• Information for traceability
• Authorised representative
Name:
Renesas Electronics Corporation
Address:
1753, Shimonumabe, Nakahara-ku, Kawasaki, Kanagawa, 211-8668, Japan
• Manufacturer
Name:
Renesas Solutions Corp.
Address:
Nippon Bldg., 2-6-2, Ote-machi, Chiyoda-ku, Tokyo 100-0004, Japan
• Person responsible for placing on the market
Name:
Renesas Electronics Europe GmbH
Address:
Arcadiastrasse 10, 40472 Dusseldorf, Germany
• Trademark and Type name
Trademark:
Renesas
Product name:
E10A-USB Emulator
Type name:
HS0005KCU01H / HS0005KCU02H
Environmental Compliance and Certifications:
• Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS)
Directive 2002/95/EC
• Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
z United States Regulatory notices
This product complies with the following EMC regulation. (This is only valid in the United States.)
FCC Certifications:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
IMPORTANT INFORMATION
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
Emulator Product:
Throughout this document, the term "emulator product" shall be defined as the following
products produced only by Renesas Electronics Corp. excluding all subsidiary products.
• Emulator
• User system interface cable
The user system or a host computer is not included in this definition.
Purpose of the Emulator Product:
This emulator product is a software and hardware development tool for systems employing the
Renesas microcomputer. This emulator product must only be used for the above purpose.
Limited Applications:
This emulator product is not authorized for use in MEDICAL, atomic energy, aeronautical or
space technology applications without consent of the appropriate officer of a Renesas sales
company. Such use includes, but is not limited to, use in life support systems. Buyers of this
emulator product must notify the relevant Renesas sales offices before planning to use the product
in such applications.
Improvement Policy:
Renesas Electronics Corp. (including its subsidiaries, hereafter collectively referred to as
Renesas) pursues a policy of continuing improvement in design, performance, and safety of the
emulator product. Renesas reserves the right to change, wholly or partially, the specifications,
design, user's manual, and other documentation at any time without notice.
Target User of the Emulator Product:
This emulator product should only be used by those who have carefully read and thoroughly
understood the information and restrictions contained in the user's manual. Do not attempt to use
the emulator product until you fully understand its mechanism.
It is highly recommended that first-time users be instructed by users that are well versed in the
operation of the emulator product.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page I of VI
LIMITED WARRANTY
Renesas warrants its emulator products to be manufactured in
accordance with published specifications and free from defects in
material and/or workmanship. Renesas, at its option, will replace any
emulator products returned intact to the factory, transportation charges
prepaid, which Renesas, upon inspection, shall determine to be defective
in material and/or workmanship. The foregoing shall constitute the sole
remedy for any breach of Renesas’ warranty. See the Renesas warranty
booklet for details on the warranty period. This warranty extends only
to you, the original Purchaser. It is not transferable to anyone who
subsequently purchases the emulator product from you. Renesas is not
liable for any claim made by a third party or made by you for a third
party.
DISCLAIMER
RENESAS MAKES NO WARRANTIES, EITHER EXPRESS OR
IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED
HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,
WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR
AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT
SHALL RENESAS BE LIABLE FOR ANY DIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE
EMULATOR PRODUCT, THE USE OF ANY EMULATOR
PRODUCT, OR ITS DOCUMENTATION, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. EXCEPT AS
EXPRESSLY STATED OTHERWISE IN THIS WARRANTY,
THIS EMULATOR PRODUCT IS SOLD "AS IS ", AND YOU
MUST ASSUME ALL RISK FOR THE USE AND RESULTS
OBTAINED FROM THE EMULATOR PRODUCT.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page II of VI
State Law:
Some states do not allow the exclusion or limitation of implied warranties or liability for
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from
state to state.
The Warranty is Void in the Following Cases:
Renesas shall have no liability or legal responsibility for any problems caused by misuse,
abuse, misapplication, neglect, improper handling, installation, repair or modifications of the
emulator product without Renesas’ prior written consent or any problems caused by the user
system.
All Rights Reserved:
This user's manual and emulator product are copyrighted and all rights are reserved by
Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form,
in hard-copy or machine-readable form, by any means available without Renesas’ prior written
consent.
Other Important Things to Keep in Mind:
1. Circuitry and other examples described herein are meant merely to indicate the characteristics
and performance of Renesas’ semiconductor products. Renesas assumes no responsibility for
any intellectual property claims or other problems that may result from applications based on
the examples described herein.
2. No license is granted by implication or otherwise under any patents or other rights of any third
party or Renesas.
Figures:
Some figures in this user's manual may show items different from your actual system.
Device names:
Sections 1 to 6 of the Debugger Part in this user’s manual use H8S/xxxx as an example of the
device names.
Limited Anticipation of Danger:
Renesas cannot anticipate every possible circumstance that might involve a potential hazard.
The warnings in this user's manual and on the emulator product are therefore not all inclusive.
Therefore, you must use the emulator product safely at your own risk.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page III of VI
SAFETY PAGE
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
DEFINITION OF SIGNAL WORDS
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
WARNING
CAUTION
CAUTION
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
NOTE emphasizes essential information.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page IV of VI
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Do not repair or remodel the emulator product by
yourself for electric shock prevention and quality
assurance.
2. Always switch OFF the host computer and user system
before connecting or disconnecting any CABLES or
PARTS.
3. Connect the connectors in the user system and in the
user interface cable by confirming the correct direction.
CAUTION
Caution to Be Taken for Disposal:
Penalties may be applicable for incorrect disposal of this waste, in accordance
with your national legislation.
European Union regulatory notices:
The WEEE (Waste Electrical and Electronic Equipment) regulations put
responsibilities on producers for the collection and recycling or disposal of
electrical and electronic waste. Return of WEEE under these regulations is
applicable in the European Union only. This equipment (including all
accessories) is not intended for household use. After use the equipment
cannot be disposed of as household waste, and the WEEE must be treated,
recycled and disposed of in an environmentally sound manner.
Renesas Electronics Europe GmbH can take back end of life equipment,
register for this service at “http://www.renesas.eu/weee”.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page V of VI
Warnings on Emulator Usage
Be sure to read and understand the warnings below before using this emulator. Note that these are
the main warnings, not the complete list.
WARNING
Always switch OFF the host computer and user system
before connecting or disconnecting any CABLES or PARTS.
Failure to do so will result in a FIRE HAZARD and will
damage the user system and the emulator product or will
result in PERSONAL INJURY. The USER PROGRAM will be
LOST.
CAUTION
Place the host computer and user system so that no
cable is bent or twisted. A bent or twisted cable will impose
stress on the user interface leading to connection or contact
failure.
Make sure that the host computer and the user system
are placed in a secure position so that they do not move
during use nor impose stress on the user interface.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page VI of VI
Introduction
The High-performance Embedded Workshop is a powerful development environment for embedded applications
targeted at Renesas microcontrollers. The main features are:
• A configurable build engine that allows you to set-up compiler, assembler and linker options via an easy to use
interface.
• An integrated text editor with user customizable syntax coloring to improve code readability.
• A configurable environment to run your own tools.
• An integrated debugger which allows you to build and debug in the same application.
• Version control support.
The High-performance Embedded Workshop has been designed with two key aims; firstly to provide you, the user, with
a set of powerful development tools and, secondly, to unify and present them in a way that is easy to use.
About This Manual
This manual describes preparation before using the emulator, emulator functions, debugging functions specific to the
emulator, tutorial, and emulator's hardware and software specifications.
Refer to the High-performance Embedded Workshop User's Manual for details on the information on the basic usage of
the High-performance Embedded Workshop, customization of the environment, build functions, and debugging
functions common to each High-performance Embedded Workshop product.
This manual does not intend to explain how to write C/C++ or assembly language programs, how to use any particular
operating system or how best to tailor code for the individual devices. These issues are left to the respective manuals.
This manual applies to v.3.00 Release 00 and later versions of the E10A-USB emulator software. The devices groups
shown below are not supported by v.3.00 Release 00 and later versions of the E10A-USB emulator software.
Table 1
E10A-USB Devices Groups which are No Longer Supported
H8S/2437 device group
H8S/2114 device group
H8S/2172 device group
H8S/2158 device group
H8S/2189R device group
H8S/2116 device group
H8S/2125 device group
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Visual SourceSafe is a trademark of Microsoft Corporation.
IBM is a registered trademark of International Business Machines Corporation.
All brand or product names used in this manual are trademarks or registered trademarks of their respective companies
or organizations.
Document Conventions
This manual uses the following typographic conventions:
Table 2
Typographic Conventions
Convention
Meaning
[Menu->Menu Option]
Bold text with ‘->’ is used to indicate menu options
(for example, [File->Save As...]).
FILENAME.C
Uppercase names are used to indicate filenames.
“enter this string”
Used to indicate text that must be entered (excluding the “” quotes).
Key + Key
Used to indicate required key presses. For example, CTRL+N
means press the CTRL key and then, whilst holding the CTRL key
down, press the N key.
(The “how to” symbol)
When this symbol is used, it is always located in the left hand
margin. It indicates that the text to its immediate right is describing
“how to” do something.
User Registration
When you install debugger software, a text file for user registration is created on your PC. Fill it in and email it to your
local distributor. If you have replaced an emulator main unit or emulation probe, rewrite an emulator name and serial
number in the text file you filled in earlier to register your new hardware products.
Your registered information is used for only after-sale services, and not for any other purposes. Without user
registration, you will not be able to receive maintenance services such as a notification of field changes or trouble
information. So be sure to carry out the user registration.
For more information about user registration, please contact your local distributor.
Table of Contents
Section 1 Overview................................................................................................................................ 1
1.1
1.2
1.3
Warnings ................................................................................................................................................................... 3
Environmental Conditions ........................................................................................................................................ 4
Components .............................................................................................................................................................. 5
Section 2 Emulator Functions ................................................................................................................ 7
2.1
2.2
Overview................................................................................................................................................................... 7
Trace Functions......................................................................................................................................................... 9
2.2.1
Branch Trace Function ................................................................................................................................... 9
2.3
Break Function........................................................................................................................................................ 10
2.4
Memory Access Functions...................................................................................................................................... 11
2.5
Stack Trace Function .............................................................................................................................................. 12
2.6
Online Help............................................................................................................................................................. 12
Section 3 Preparation before Use......................................................................................................... 13
3.1
Emulator Preparation .............................................................................................................................................. 13
3.2
Emulator Hardware Configuration.......................................................................................................................... 14
3.3
CD-R....................................................................................................................................................................... 19
3.4
Installing Emulator’s Software ............................................................................................................................... 19
3.5
Connecting the Emulator to the Host Computer ..................................................................................................... 20
3.6
Connecting the Emulator to the User System ......................................................................................................... 22
3.7
Connecting System Ground .................................................................................................................................... 25
3.8
Setting the DIP Switches......................................................................................................................................... 26
3.9
Interface Circuits in the Emulator ........................................................................................................................... 28
3.10 Setting up the Emulator........................................................................................................................................... 29
3.10.1
Setting up at Purchasing the Emulator or Updating the Version of Software .............................................. 30
3.10.2
Setting up the Emulator by Using the License Tool to Add a Device Group............................................... 35
3.11 System Check.......................................................................................................................................................... 40
Section 4 Preparations for Debugging ................................................................................................. 53
4.1
Method for Activating High-performance Embedded Workshop........................................................................... 53
4.1.1
Creating the New Workspace (Toolchain Not Used) ................................................................................... 54
4.1.2
Creating the New Workspace (Toolchain Used) .......................................................................................... 58
4.1.3
Selecting an Existing Workspace ................................................................................................................. 64
4.2
Setting at Emulator Activation................................................................................................................................ 66
4.2.1
Setting at Emulator Activation ..................................................................................................................... 66
4.2.2
Downloading a Program............................................................................................................................... 68
4.2.3
Setting the Program Flash Mode .................................................................................................................. 69
4.3
Debug Sessions ....................................................................................................................................................... 76
4.3.1
Selecting a Session ....................................................................................................................................... 76
4.3.2
Adding and Removing Sessions................................................................................................................... 78
4.3.3
Saving Session Information.......................................................................................................................... 81
4.4
Connecting the Emulator ........................................................................................................................................ 82
4.5
Reconnecting the Emulator ..................................................................................................................................... 83
4.6
Ending the Emulator ............................................................................................................................................... 84
Section 5 Debugging............................................................................................................................ 85
5.1
Setting the Environment for Emulation .................................................................................................................. 85
5.1.1
Opening the [Configuration] Dialog Box..................................................................................................... 85
5.1.2
[Emulator] Page............................................................................................................................................ 85
5.2
Downloading a Program ......................................................................................................................................... 90
5.2.1
Downloading a Program............................................................................................................................... 90
5.2.2
Viewing the Source Code............................................................................................................................. 91
5.2.3
Viewing the Assembly-Language Code ....................................................................................................... 94
5.2.4
Modifying the Assembly-Language Code.................................................................................................... 96
5.2.5
Viewing a Specific Address ......................................................................................................................... 97
5.2.6
Viewing the Current Program Counter Address........................................................................................... 97
5.3
Using the Event Points ............................................................................................................................................ 98
5.3.1
PC Breakpoints............................................................................................................................................. 98
5.3.2
Break Conditions.......................................................................................................................................... 98
5.3.3
Opening the [Event] Window....................................................................................................................... 98
5.3.4
Setting PC Breakpoints ................................................................................................................................ 99
5.3.5
Add............................................................................................................................................................. 100
5.3.6
Edit ............................................................................................................................................................. 100
5.3.7
Enable......................................................................................................................................................... 100
5.3.8
Disable........................................................................................................................................................ 100
5.3.9
Delete ......................................................................................................................................................... 100
5.3.10
Delete All ................................................................................................................................................... 100
5.3.11
Go to Source............................................................................................................................................... 100
5.3.12
[Set Break] Dialog Box .............................................................................................................................. 101
5.3.13
Setting Break Conditions............................................................................................................................ 103
5.3.14
Edit... .......................................................................................................................................................... 104
5.3.15
Enable......................................................................................................................................................... 104
5.3.16
Disable........................................................................................................................................................ 104
5.3.17
Delete ......................................................................................................................................................... 104
5.3.18
Delete All ................................................................................................................................................... 105
5.3.19
Go to Source............................................................................................................................................... 105
5.3.20
Sequential Conditions ................................................................................................................................ 105
5.3.21
Editing Break Conditions ........................................................................................................................... 105
5.3.22
Modifying Break Conditions...................................................................................................................... 105
5.3.23
Enabling Break Conditions ........................................................................................................................ 105
5.3.24
Disabling Break Conditions ....................................................................................................................... 106
5.3.25
Deleting Break Conditions ......................................................................................................................... 106
5.3.26
Deleting All Break Conditions ................................................................................................................... 106
5.3.27
Viewing the Source Line for Break Conditions ......................................................................................... 106
5.3.28
[Break condition 1] Dialog Box ................................................................................................................. 107
5.4
Viewing the Trace Information............................................................................................................................. 112
5.4.1
Opening the [Trace] Window..................................................................................................................... 112
5.4.2
Acquiring Trace Information...................................................................................................................... 112
5.4.3
Clearing the Trace Information .................................................................................................................. 113
5.4.4
Saving the Trace Information in a File....................................................................................................... 113
5.4.5
Viewing the [Editor] Window .................................................................................................................... 114
5.4.6
Trimming the Source.................................................................................................................................. 114
5.5
Using the Start/Stop Function ............................................................................................................................... 114
5.5.1
Opening the [Start/Stop Function Setting] Dialog Box.............................................................................. 114
5.5.2
Specifying the Routine to be Executed ...................................................................................................... 116
5.6
Operation with Multiple Debugging Platforms..................................................................................................... 118
5.6.1
Distinguishing Two Emulators................................................................................................................... 118
5.7
Saving of Hardware-Break Settings...................................................................................................................... 122
5.7.1
Saving and Loading Hardware-Break Settings .......................................................................................... 122
5.7.2
How to Save Hardware-Break Settings ...................................................................................................... 122
5.7.3
How to Load Hardware-Break Settings...................................................................................................... 123
Section 6 Tutorial............................................................................................................................... 125
6.1
6.2
6.3
6.4
6.5
6.6
Introduction........................................................................................................................................................... 125
Running the High-performance Embedded Workshop ......................................................................................... 125
Setting up the Emulator......................................................................................................................................... 125
Setting the [Configuration] Dialog Box ................................................................................................................ 126
Checking the Operation of RAM .......................................................................................................................... 128
Downloading the Tutorial Program ...................................................................................................................... 130
6.6.1
Downloading the Tutorial Program............................................................................................................ 130
6.6.2
Displaying the Source Program.................................................................................................................. 131
6.7
Setting a PC Breakpoint........................................................................................................................................ 132
6.8
Setting Registers ................................................................................................................................................... 133
6.9
Executing the Program.......................................................................................................................................... 135
6.10 Reviewing Breakpoints ......................................................................................................................................... 138
6.11 Viewing Memory .................................................................................................................................................. 139
6.12 Watching Variables............................................................................................................................................... 141
6.13 Stepping Through a Program ................................................................................................................................ 145
6.13.1
Executing [Step In] Command ................................................................................................................... 145
6.13.2
Executing [Step Out] Command ................................................................................................................ 147
6.13.3
Executing [Step Over] Command .............................................................................................................. 148
6.14 Forced Breaking of Program Executions .............................................................................................................. 150
6.15 Displaying Local Variables................................................................................................................................... 151
6.16 Break Function...................................................................................................................................................... 152
6.16.1
PC Break Function ..................................................................................................................................... 152
6.17 Hardware Break Function ..................................................................................................................................... 158
6.18 Trace Functions..................................................................................................................................................... 163
6.18.1
Displaying the Trace Window.................................................................................................................... 163
6.19 Stack Trace Function ............................................................................................................................................ 164
6.20 What Next? ........................................................................................................................................................... 165
Section 7 Maintenance and Guarantee............................................................................................... 167
7.1
7.2
7.3
7.4
User Registration .................................................................................................................................................. 167
Maintenance.......................................................................................................................................................... 167
Guarantee .............................................................................................................................................................. 167
Repair Provisions .................................................................................................................................................. 168
7.4.1
Repair with Extra-Charge........................................................................................................................... 168
7.4.2
Replacement with Extra-Charge................................................................................................................. 168
7.4.3
Expiration of the Repair Period.................................................................................................................. 168
7.4.4
Transportation Fees at Sending Your Product for Repair .......................................................................... 168
7.5
How to Make a Request for Repair....................................................................................................................... 169
Appendix A
Troubleshooting ....................................................................................................... 171
Appendix B
Window Functions.................................................................................................... 173
Appendix C
Command-Line Functions ........................................................................................ 177
Appendix D
Notes on High-performance Embedded Workshop ................................................. 179
Appendix E
Diagnostic Test Procedure ........................................................................................ 185
Appendix F
Repair Request Sheet ................................................................................................ 187
H8S, H8SX Family E10A-USB Emulator
Section 1 Overview
Section 1 Overview
The E10A-USB emulator (hereafter referred to as the emulator) is a support tool for developing
application systems to run on Renesas original microcomputers.
The main unit of the emulator is connected, through the dedicated debugging interface, to the user
system. The user system can be debugged under the conditions similar to the actual application
conditions. The emulator enables debugging anywhere indoors or out. The host computer for
controlling the emulator must be an IBM PC compatible machine with USB 1.1/2.0 (Full-Speed).
Figure 1.1 shows the system configuration using the emulator.
Connected to
the USB connector
USB cable (1.5 m)
B
US
B
A
US
E10
I/F
RENESAS
Host computer (with USB interface)
User system interface cable
ACT
CD-R
High-performance
Embedded Workshop
User system
Connected to
the USB connector
User system connector
Figure 1.1 System Configuration with the Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 1 of 190
H8S, H8SX Family E10A-USB Emulator
Section 1 Overview
The emulator provides the following features:
• Excellent cost-performance emulator
Compactness and connection to the USB are obtained.
• Realtime emulation
Realtime emulation of the user system is enabled at the maximum operating frequency of the
CPU.
• Excellent operability
Using the High-performance Embedded Workshop enables user program debugging using a
pointing device such as a mouse. The High-performance Embedded Workshop enables highspeed downloading of load module files.
• Various debugging functions
Various break and trace functions enable efficient debugging. Breakpoints and break
conditions can be set by the specific window, trace information can be displayed on a window,
and command-line functions can be used.
• Debugging of the user system in the final development stage
The user system can be debugged under conditions similar to the actual application conditions.
• Compact debugging environment
When the emulator is used, a laptop computer can be used as a host computer, creating a
debugging environment in any place.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 2 of 190
H8S, H8SX Family E10A-USB Emulator
1.1
Section 1 Overview
Warnings
CAUTION
READ the following warnings before using the emulator
product. Incorrect operation will damage the user system and
the emulator product. The USER PROGRAM will be LOST.
1. Check all components against the component list after unpacking the emulator.
2. Never place heavy objects on the casing.
3. Protect the emulator from excessive impacts and stresses. For details, refer to section 1.2,
Environmental Conditions.
4. When moving the host computer or user system, take care not to vibrate or damage it.
5. After connecting the cable, check that it is connected correctly. For details, refer to section 3,
Preparation before Use.
6. Supply power to the connected equipment after connecting all cables. Cables must not be
connected or removed while the power is on.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 3 of 190
H8S, H8SX Family E10A-USB Emulator
1.2
Section 1 Overview
Environmental Conditions
CAUTION
Observe the conditions listed in tables 1.1 and 1.2 when
using the emulator. Failure to do so will cause illegal
operation in the user system, the emulator product, and the
user program.
Table 1.1 Environmental Conditions
Item
Specifications
Temperature
Operating:
Storage:
+10°C to +35°C
–10°C to +50°C
Humidity
Operating:
Storage:
35% RH to 80% RH, no condensation
35% RH to 80% RH, no condensation
Vibration
Operating:
Storage:
Transportation:
2.45 m/s max.
2
4.9 m/s max.
2
14.7 m/s max.
Ambient gases
No corrosive gases may be present
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
2
Page 4 of 190
H8S, H8SX Family E10A-USB Emulator
Section 1 Overview
Table 1.2 lists the acceptable operating environments.
Table 1.2 Operating Environments
®
Item
32-Bit Editions of Windows XP
32-Bit Editions of Windows
®
Vista or 32-Bit or 64-Bit
®
Editions of Windows 7
Host computer
Built-in Pentium III or higher-performance CPU (1 GHz or higher
recommended); IBM PC or compatible machine with USB 1.1/2.0 (FullSpeed).
CPU
Pentium III (1 GHz) or higher
recommended
Pentium 4 (3 GHz), Core™ 2 Duo
(1 GHz), or higher recommended
Minimum memory
capacity
1 Gbyte or more recommended
1.5 Gbyte or more recommended
(at least 10 times the size of the
load module file)
Hard-disk capacity
Installation disk capacity: 600 Mbytes or more. (Prepare an area at
least double the memory capacity (four-times or more recommended)
as the swap area.)
Pointing device such as
mouse
Connectable to the host computer; compatible with Windows XP,
®
®
Windows Vista , or Windows 7
Display
Monitor resolution: 1024 x 768 or higher
®
®
®
®
Power voltage
5.0 ± 0.25 V (USB-bus power type)
Current consumption
HS0005KCU01H: 260 mA (max.)
HS0005KCU02H: 420 mA (max.)
CD-ROM drive
Required to install the High-performance Embedded Workshop for the
emulator or refer to the emulator user’s manual.
Microsoft, Windows, and Windows Vista are either registered trademarks or trademarks of
Microsoft Corporation in the United States and or other countries. All other brand and product
names are trademarks, registered trademarks or service marks of their respective holders.
1.3
Components
Check that all of the components are present when unpacking the product. For details on the
emulator components, refer to section 1.1 in the additional document, Supplementary Information
on Using the H8S/xxxx and Supplementary Information on Using the H8SX/xxxx. If all of the
components are not present, contact your nearest Renesas sales office.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 5 of 190
H8S, H8SX Family E10A-USB Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Section 1 Overview
Page 6 of 190
H8S, H8SX Family E10A-USB Emulator
Section 2 Emulator Functions
Section 2 Emulator Functions
This section describes the emulator functions. They differ according to the device supported by
the emulator. For the usage of each function, refer to section 6, Tutorial.
2.1
Overview
Table 2.1 gives a functional overview of the emulator.
For details on the functions of each product, refer to the online help.
Table 2.1 Emulator Functions
No.
Item
Function
1
User program execution
function
•
Executing user programs at an operating frequency within
the range guaranteed for the MCU.
•
Reset emulation
•
Step functions:
Single step (one step: one instruction)
Source-level step (one step: one-line source)
Step over (a break did not occur in a subroutine)
Step out (when the PC points to a location within a
subroutine, execution continues until it returns to the calling
function)
•
Issues a power-on reset from the High-performance
Embedded Workshop to the MCU during break.
2
Reset function
3
Trace functions
4
Break functions
•
Trace function incorporated in the MCU
•
Branch trace (conditions and the number of branches differ
depending on the MCU)
•
Hardware break function (functions and the number of
functions differ depending on the MCU)
•
PC break function (255 points)
•
Forced break function
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 7 of 190
H8S, H8SX Family E10A-USB Emulator
Section 2 Emulator Functions
Table 2.1 Emulator Functions (cont)
No.
Item
5
Memory access functions
Function
•
Downloading to RAM
•
Downloading to flash memory
•
Single-line assembly
•
Reverse assembly (disassembly)
•
Reading of memory
•
Writing to memory
•
Automatic updating of a display of selected variables during
user program execution
•
Fill
•
Search
•
Move
•
Copy
6
General/control register
access function
Reads or writes the general/control registers.
7
Internal I/O register
access function
Reads or writes the internal I/O registers.
8
Source-level debugging
function
Various source-level debugging functions.
9
Command line function
Supports command input.
Batch processing is enabled when a file is created by arranging
commands in input order.
10
Help function
Describes the usage of each function or command syntax input
from the command line window.
The specific functions of the emulator are described in the next section.
Note: The number of hardware break conditions, trace conditions, branches, and MCU internaltrace functions differs according to the MCU. For the specifications of a given MCU, refer
to the online help or the supplementary document.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 8 of 190
H8S, H8SX Family E10A-USB Emulator
2.2
Section 2 Emulator Functions
Trace Functions
The emulator has a trace function.
Note: The number of branch instructions that can be acquired by a trace differs according to the
product. For the number that can be specified for each product, refer to the online help.
2.2.1
Branch Trace Function
The branch source addresses, mnemonics, operands, and source lines are displayed. Since this
function uses the trace buffer built into the MCU, a realtime trace can be acquired.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 9 of 190
H8S, H8SX Family E10A-USB Emulator
2.3
Section 2 Emulator Functions
Break Function
The emulator has the following three break functions.
(1) Hardware break function (Break condition)
Uses a break controller incorporated in the MCU.
The access address, instruction fetch address, data, or bus cycle condition can be set. The
logical address is the address condition.
This function can be also set from the [Event] column in the [Editor] or [Disassembly] window.
For the setting, refer to section 5.2, Downloading a Program.
(2) PC break function (BREAKPOINT)
Breaks when the dedicated instruction at the specified address that has been replaced is
executed.
This function can be set in the [Breakpoint] page of the [Event] dialog box.
It can also be set when the [S/W breakpoint] column for the line to be set is double-clicked in
the [Source] or [Disassembly] window.
(3) Forced break function
Forcibly breaks the user program.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 10 of 190
H8S, H8SX Family E10A-USB Emulator
2.4
Section 2 Emulator Functions
Memory Access Functions
The emulator has the following memory access functions.
(1) Memory read/write function
[Memory] window: The memory contents are displayed in the window. Only the amount
specified when the [Memory] window is opened can be read. Since there is
no cache in the emulator, read cycles are always generated. If the memory is
written in the [Memory] window, read cycles in the range displayed in the
[Memory] window will occur for updating the window. When the [Memory]
window is not to be updated, change the setting in [Lock Refresh] from the
popup menu.
me (memory_edit) command:
A command line function that reads or writes the specified
amount of memory at the specified address.
(2) User program downloading function
A load module registered in the workspace can be downloaded. Such module can be selected
from [Download Module] in the [Debug] menu. Downloading is also possible by a popup menu
that is opened by right-clicking on the mouse at the load module in the workspace. The user
program is downloaded to the RAM or flash memory.
This function also downloads information required for source-level debugging such as debugging
information.
(3) Memory data uploading function
The specified amount of memory from the specified address can be saved in a file. Select [Save
Memory] from the [Debug] menu or select the [Save] item from the popup menu in the [Memory]
window.
(4) Memory data downloading function
The memory contents saved in a file can be downloaded. Select [Load] from the popup menu in
the [Memory] window.
(5) Displaying the variable contents
The variable contents specified in the user program are displayed.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 11 of 190
H8S, H8SX Family E10A-USB Emulator
Section 2 Emulator Functions
(6) Other memory operation functions
Other functions are as follows:
• Memory fill
• Memory copy
• Memory save
• Memory verify
• Memory search
• Internal I/O display
• Displaying label and variable names and their contents
For details, refer to the online help.
Note: Memory access during user program execution:
When memory is accessed from the memory window, etc. during execution of the user
program, the user program is resumed after it has stopped in the emulator to access the
memory. Therefore, realtime emulation cannot be performed.
The stopping time of the user program is as follows:
Environment:
TM
Host computer: Core 2 Duo 2 GHz
H8S/2377F: 33 MHz (system clock frequency)
When a one-byte memory is read from the command-line window, the stopping time will
be about 65 ms.
2.5
Stack Trace Function
The emulator uses the information on the stack to display the names of functions in the sequence
of calls that led to the function to which the program counter is currently pointing. This function
can be used only when the load modules that have the following formats are loaded:
– H8SX, H8S, H8 family series C/C++ compiler (such as [R0C40008XSW06R]): Elf/Dwarf2
For the usage of this function, refer to section 6.19, Stack Trace Function.
2.6
Online Help
An online help explains the usage of each function or the command syntax that can be entered
from the command line window.
Select [Emulator Help] from the [Help] menu to view the emulator help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 12 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Section 3 Preparation before Use
3.1
Emulator Preparation
Unpack the emulator and prepare it for use as follows:
WARNING
READ the reference sections shaded in figure 3.1 before
using the emulator product. Incorrect operation will damage
the user system and the emulator product. The USER
PROGRAM will be LOST.
Reference
Unpack the emulator
Component list
Check the components against the component list
When the emulator
is used first.
Set up the emulator
- Install the emulator's software
(Check the components and register the user information.)
- Insert the emulator
- Set up the main unit of the emulator
Section 3
Start the High-performance Embedded Workshop
Section 4
Turn on the user system
When the emulator
is used for second
time or later.
Figure 3.1 Emulator Preparation Flow Chart
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 13 of 190
H8S, H8SX Family E10A-USB Emulator
3.2
Section 3 Preparation before Use
Emulator Hardware Configuration
As shown in figure 3.2, the emulator consists of an emulator, a USB cable, and a user system
interface cable. The emulator is connected to the host computer via USB 1.1, and also to the USB
port conforming to USB 2.0.
Figure 3.2 Emulator Hardware Configuration (when the 14-pin Type Connector is Used)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 14 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
The names of each section of the emulator are explained next.
Emulator Top View:
Figure 3.3 Emulator Top View
(a) E10A-USB logo plate: A yellow plate (for HS0005KCU01H) or a red plate (for
HS0005KCU02H) dedicated for the emulator is provided to be easily
distinguished from other E-series emulators.
(b) Sliding switch cover:
A cover to protect switches for setting the emulator, which is closed
to prevent incorrect operation. Be sure to close this cover during
emulation.
(c) ACTION LED:
Marked ‘ACT’. When this LED is lit, the E10A-USB control
software is in operation.
(d) Host connector:
Marked ‘
’. A connector for the host computer is provided at the
side of this mark.
(e) User connector:
Marked ‘USER I/F’. A connector for the user system interface cable
is provided at the side of this mark.
Note: Even if the LED is not lit, the USB is not disconnected or malfunctioned.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 15 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Emulator Host-side View:
Figure 3.4 Emulator Host-side View
(a) Host-side connector:
A USB connector for the host computer. Be sure to connect the
provided USB cable.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 16 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Emulator User-side View:
Figure 3.5 Emulator User-side View
(a) User-side connector:
A user system interface cable is connected.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 17 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Emulator Bottom View:
(a)
MODEL : HS0005KCU01H
(HS0005KCU01H)
SERIAL No. : 00001A
This device complies with Part 15 of the FCC Rules.
Operation is subject to the follow ing two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
SH-2
SH-3
SH-4
SH-4A
SH-Mobile
NewSH-Mobile
SH- 2A
SH4 AL-D SP
H8 S
H8 SX
MPEG
MADE IN JAPAN
Figure 3.6 Emulator Bottom View
(a) Label for product management: The serial number, revision, and safety standard, etc. of the
emulator are written to. The contents differ depending on the
time when you purchased the product.
Only one device group can be set up using the setup tool when
the emulator is purchased. Be sure to check the device group
you have selected on the label for product management.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 18 of 190
H8S, H8SX Family E10A-USB Emulator
3.3
Section 3 Preparation before Use
CD-R
The root directory of the CD-R contains a setup program for installing the emulator’s software.
The folders contain the files and programs listed below.
Table 3.1 Contents of the CD-R Directories
Directory Name
Contents
®
Description
Dlls
Microsoft runtime library
A runtime library for the High-performance
Embedded Workshop. The version is
checked at installation and this library is
copied to the hard disk as part of the
installation process.
Drivers
E10A-USB emulator driver
USB drivers for the E10A-USB emulator.
Help
Online help for the E10A-USB
emulator
An online help file. This is copied to the hard
disk as part of the installation process.
Manuals
E10A-USB emulator manuals
E10A-USB emulator user’s manuals. They
are provided as PDF files.
3.4
Installing Emulator’s Software
Execute HewInstMan.exe from the root directory of the CD-R to start the installation manager.
Follow the cues given by the installation manager to install the software.
Note: When a driver is installed in Windows® XP, a warning message on the Windows® logo
test may be displayed, but it is not a problem. Select [Continue Anyway] to proceed with
driver installation.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 19 of 190
H8S, H8SX Family E10A-USB Emulator
3.5
Section 3 Preparation before Use
Connecting the Emulator to the Host Computer
This section describes how to connect the emulator to the host computer. For the position of each
connector of the emulator, refer to section 3.2, Emulator Hardware Configuration.
Note: Be sure to install the software for the emulator before putting the emulator in place.
WARNING
Always switch OFF the emulator product and the user
system before connecting or disconnecting any CABLES
except for the USB interface cable. Failure to do so will result
in a FIRE HAZARD and will damage the user system and the
emulator product or will result in PERSONAL INJURY.
The USER PROGRAM will be LOST.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 20 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
The emulator is connected to the host computer via the USB 1.1, and also to the USB port
conforming to USB 2.0. Figure 3.7 shows the system configuration.
Figure 3.7 System Configuration when Connecting the Emulator to the Host Computer
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 21 of 190
H8S, H8SX Family E10A-USB Emulator
3.6
Section 3 Preparation before Use
Connecting the Emulator to the User System
Use the procedure below to connect the emulator to the user system with the user system interface
cable, or to disconnect them when moving the emulator or the user system.
1. Check that the host computer is turned off or the emulator is not connected to the host
computer with the USB cable.
2. Connect the user system interface cable to the user-side connector of the emulator.
3. Connect the USB cable to the host-side connector of the emulator.
Figure 3.8 shows the position of the connector.
Figure 3.8 Position of the Connector
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 22 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
(1) The user system connector must be installed to the user system. Table 3.2 shows the
recommended user system connector for the emulator.
Table 3.2 Recommended User System Connector
Connector
Type Number
Manufacturer
Specifications
14-pin connector
2514-6002
3M Limited
14-pin straight type
Note: When designing the 14-pin connector layout on the user board, do not place any
components within 3 mm of the user system connector.
(2) The pin assignments of the user system connector are shown in section 1 in the additional
document, Supplementary Information on Using the H8S/xxxx, or Supplementary Information
on Using the H8SX/xxxx.
(3) Connect pins 8, 9, 10, 12, 13, and 14 (when using the 14-pin user system interface cable) of the
user system connector to GND firmly on the PCB. These pins are used as electrical GND and
to monitor the connection of the user system connector. Note the pin assignments of the user
system connector.
User system interface cable
Tab
GND line
User system connector
Pin 8
User system GND
connection
Pin 1
User system
Figure 3.9 Connecting the User System Interface Cable to the User System
when the 14-pin Type Connector is Used
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 23 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
CAUTION
Note that the pin number assignments of the user system
connector differ from those of the connector manufacturer.
Notes: 1. Connection of the signals differs depending on the package. For details, refer to the
MCU pin assignments.
2. To remove the 14-pin type user system interface cable from the user system, pull the
tab on the connector upward.
3. The range of communication that the emulator operates at is different depending on the
MCU used.
4.
To connect the signals from the connector, refer to section 1 in the additional
document, Supplementary Information on Using the H8S/xxxx, or Supplementary
Information on Using the H8SX/xxxx.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 24 of 190
H8S, H8SX Family E10A-USB Emulator
3.7
Section 3 Preparation before Use
Connecting System Ground
WARNING
Separate the frame ground from the signal ground at the
user system. Failure to do so will result in a FIRE HAZARD
and will damage the user system and the emulator product or
will result in PERSONAL INJURY.
The emulator's signal ground is connected to the user system's signal ground. In the emulator, the
signal ground and frame ground are connected. In the user system, connect the frame ground only;
do not connect the signal ground to the frame ground (figure 3.10).
If it is difficult to separate the frame ground from the signal ground in the user system, set the
GND for DC power input (AC adapter) of the host computer and the frame ground of the user
system as the same potential. If the GND potential is different between the host computer and the
user system, an overcurrent will flow in the low-impedance GND line and thin lines might be
burned.
Figure 3.10 Connecting System Ground
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 25 of 190
H8S, H8SX Family E10A-USB Emulator
3.8
Section 3 Preparation before Use
Setting the DIP Switches
WARNING
Do not change switches (SW2 and SW3) while the
emulator and the user sytem are turned on. The changing of
switches (SW2 and SW3) will result in a FIRE HAZARD and
will damage the user system and the emulator product. The
USER PROGRAM will be LOST.
The emulator incorporates three switches; set all of them to 1 in general, and set SW1 to 0 only
when the emulator is set up.
USB I/F
B
US
0A
E1
ACT
1
1
2
2
3
3
ON
OFF
Figure 3.11 DIP Switches
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 26 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Table 3.3 shows the relationships between settings and functions of DIP switches 1 to 3. Use the
settings depending on the usage of the user system.
CAUTION
Use only the settings shown in table 3.3. Use of other
settings will not activate the emulator. The USER PROGRAM
will be LOST.
• Settings for use of the 14-pin user interface cable
Description: The settings of the UVCC pin of the user interface connector apply to SW2. In the
H8S, H8SX family E10A-USB emulator, connect the UVCC pin to the VCC power supply that is
connected to the VCC pin of the MCU for the user system.
Table 3.3 Switch Settings of the E10A-USB
Switch Settings
SW1
SW2
State of the E10A-USB
SW3
UVCC
Condition
0 (off)
1
1
-
The emulator is set up
1 (on)
1 (on)
1 (on)
1.8 V to 5.0 V*
Normal
Note: The range differs depending on the MCU.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 27 of 190
H8S, H8SX Family E10A-USB Emulator
3.9
Section 3 Preparation before Use
Interface Circuits in the Emulator
Figure 3.12 shows interface circuits in the emulator. Use them as a reference to determine the
value of the pull-up resistance.
Note: The 74LVC2G125 operates at VCC (1.8 to 5.0 V) from the user system connector.
3.3 V
SW2
0
Emulator control circuit
1
User system connector
on the user system
11 UVCC
SN74LVC2G125
22 Ω
VCC
A
10 kΩ
1*1
Y
SN74LVC2G125
22 Ω
VCC
A
PI74AVC164245
SN74LVC2G125
A
PI74AVC164245
Y
22 Ω
SN74LVC2G125
A
10 kΩ
3*1
A
1.8 V
22 Ω
VCC
B
2 *1
1.8 V
VCC
B
10 kΩ
Y
Y
10 kΩ
4 RES(in)# *2
A
SN74LVC2G125
VCC
A
Y
SN74LVC2G125
22 Ω
VCC
A
10 kΩ
5 *1
Y
SN74LVC2G125
22 Ω
VCC
A
PI74AVC164245
SN74LVC2G125
VCC
B
A
Y
10 kΩ
6*1
Y
1.8 V
22 Ω
10 kΩ
A
7 RES(out)# *3
SN74LVC2G125
VCC
OE
A
Y
Notes: 1. In the H8S, H8SX family, these pin names differ depeding on the MCU. Refer to each additional document.
2. When the H8S, H8SX family is connected, the emulator outputs the reset signal to pin 4. Therefore, pin 4 cannot be directly
connected to pin RES# of the MCU.
3. When the H8S, H8SX family is connected, the emulator only monitors pin 7.
Figure 3.12 Interface Circuits in the Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 28 of 190
H8S, H8SX Family E10A-USB Emulator
3.10
Section 3 Preparation before Use
Setting up the Emulator
Set up the emulator’s firmware using the following procedures. Here describes how to set up the
H8S device group.
Note: Only one device group can be set up using the setup tool when the emulator is purchased.
Be sure to check the device group you have selected on the label for product management
attached to the back of the emulator box. To use the emulator for another device group
after set up, purchase the license tool to add a device group.
CAUTION
Do not disconnect the USB cable unless instructed to do
so by an on-screen message. Incorrect operation will damage
the emulator product.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 29 of 190
H8S, H8SX Family E10A-USB Emulator
3.10.1
Section 3 Preparation before Use
Setting up at Purchasing the Emulator or Updating the Version of Software
Note: If you are using the HS0005KCU01H (serial No.: 03311C or later) or HS0005KCU02H
(serial No.: 04146E or later) emulator hardware, the below procedure may not be required;
follow the procedure only when the dialog box shown in figure 3.13 or 3.14 is displayed
by using the procedure described in section 3.11, System Check.
Figure 3.13 [Emulator firmware error (1)] Dialog Box
Figure 3.14 [Emulator firmware error (2)] Dialog Box
(1) Open the sliding switch cover and check that the switch (SW1) for setting the emulator is
turned to ‘1’.
(2) Select [Renesas] -> [High-performance Embedded Workshop] -> [Setup tool for E10A-USB
Emulator] -> [H8S/xxxx Device Group] from [Programs] in the [Start] menu. A tool for
setting up the emulator is activated.
Note: When the H8SX device group is used, select [H8SX Device Group].
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 30 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Figure 3.15 [Start] Menu
Figure 3.16 Setup Tool for Emulator
(a) Device group of the emulator firmware:
Name of the device group currently set.
(b) Version number of the emulator firmware:
The version number of software for controlling the
H8S Device Group in the emulator. This item is
displayed only when the H8S Device Group is
available.
(c) Version number of the setup program:
The version number of the setup program.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 31 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Notes: 1. If the version numbers shown in (b) and (c) are the same, setup of the emulator is not
required. Setup the emulator only when “-.-.--.---“ is shown in (b) or the version
number of (b) is older than that of (c).
2. If an emulator other than the H8S/xxxx E10A-USB is connected, the following error
message will be displayed to exit the setup tool.
Figure 3.17 Error Message (1)
3. If the following error message is displayed, the host computer is not connected to the
emulator or the setup switch (SW1) is turned to ‘0’.
Figure 3.18 Error Message (2)
If the setup switch (SW1) is turned to ‘0’, set it to ‘1’ and connect the USB cable again.
(3) Clicking the [Setup] button displays the following dialog box.
Figure 3.19 [Setup tool for H8S E10A-USB Emulator] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 32 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
(4) Turn the setup switch (SW1) to ‘0’, connect the USB cable again, and click the [OK] button.
Setting up the emulator’s firmware is started.
Notes: 1. If the following dialog message is displayed, insert the USB cable again.
Figure 3.20 [Setup tool for H8S E10A-USB Emulator] Dialog Box (3)
2. When [Add New Hardware Wizard] is displayed, select [Install the software
automatically].
The above case only applies when the emulator is setup initially or the USB port on the
host computer side is changed and used for first connection. The time may be required
until [Add New Hardware Wizard] is displayed.
3. Although a dialog box will be displayed to indicate disconnection of the USB, this is
not a problem.
CAUTION
Do not turn off the host computer or disconnect the USB
cable while setting up the emulator. The emulator may be
damaged.
Figure 3.21 Start of Setting up the Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 33 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
(5) When the following dialog box is displayed, setting up the emulator is completed.
Figure 3.22 Message for Completion of Setting up the Emulator
(6)
When setting up the emulator has been completed, the following message will be displayed.
Turn the setup switch (SW1) to ‘1’, connect the USB cable again, and click the [OK] button.
Figure 3.23 [Setup Tool for H8S E10A-USB Emulator] Dialog Box
Notes: 1. Be sure to turn the setup switch (SW1) to ‘1’ except when the setup tool is used.
2. To use the license tool for another device group, it is necessary to set up the firmware
by using the setup tool or license tool that corresponds to the device group. To use the
setup tool, however, the license tool must also be installed. For details on the license
tool, refer to the following section.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 34 of 190
H8S, H8SX Family E10A-USB Emulator
3.10.2
Section 3 Preparation before Use
Setting up the Emulator by Using the License Tool to Add a Device Group
In the license tool, the emulator for the current product group can be used for debugging another
product group (device group such as SHxxxx Device Group, H8S Device Group, or H8SX Device
Group that is supported by the emulator).
In this section, the names of the device group that have already been installed and another device
group to be added by the license tool are shown as SHxxxx Device Group and H8S Device Group,
respectively. Replace these names according to your environment when you read this section.
The license tool to add a device group does not include software for the E10A-USB emulator.
Install the software for your product group by using the CD-R provided for the emulator or
accessing the data on the web site.
Note: If no product groups have been installed in the emulator at the time of purchase, do not use
the license tool.
Refer to section 3.10.1, Setting up at Purchasing the Emulator or Updating the Version of
Software, and use the setup tool.
(1) Installing the emulator
Inserting the CD-R into the CD-ROM drive automatically activates the installation wizard (to
prevent automatic activation, insert the CD-R by pressing the Shift key). If the installation wizard
is not automatically activated, execute setup.exe from the root directory of the CD-R.
Follow the instructions by the installation wizard.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 35 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
(2) Setting up the emulator
1. Open the sliding switch cover and check that the switch (SW1) for setting the emulator is
turned to ‘1’.
2. Select [Renesas] -> [License tool for E10A-USB] -> [H8S Device Group] from [Programs]
in the [Start] menu. This starts up the license tool to add a device group to the emulator.
Figure 3.24 [Start] Menu
Figure 3.25 License Tool for Emulator
(a) Device group of the emulator firmware:
Name of the device group currently set.
(b) Version number of the emulator firmware:
The version number of software for controlling the
H8S Device Group in the emulator. This item is
displayed only when the H8S Device Group is
available.
(c) Version number of the setup program:
The version number of the setup program.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 36 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Notes: 1. If the version numbers shown in (b) and (c) are the same, setup of the emulator is not
required. Set up the emulator only when “-.-.--.---“ is shown in (b) or the version
number of (b) is older than that of (c).
2. If the following error message is displayed, the host computer is not connected to the
emulator or the setup switch (SW1) is turned to ‘0’.
Figure 3.26 Error Message (4)
If the setup switch (SW1) is turned to ‘0’, set it to ‘1’ and connect the USB cable again.
(3)
Click the [Setup] button.
When the following dialog box is displayed, turn the setup switch (SW1) to ‘0’, connect the
USB cable again, and click the [OK] button.
Figure 3.27 [License tool for H8S E10A-USB Emulator] Dialog Box
(4)
Setting up the emulator’s control software is started.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 37 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Notes: 1. If the following dialog message is displayed, insert the USB cable again.
Figure 3.28 [License tool for H8S E10A-USB Emulator] Dialog Box
2. When [Add New Hardware Wizard] is displayed, select [Install the software
automatically].
The above case only applies when the USB port on the host computer side is changed
and used for first connection. The time may be required until [Add New Hardware
Wizard] is displayed.
3. Although a dialog box will be displayed to show the disconnection of the USB, this is
not a problem.
CAUTION
Do not turn off the host computer or disconnect the USB
cable while setting up the emulator. The emulator may be
damaged.
Figure 3.29 Start of Setting up the Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 38 of 190
H8S, H8SX Family E10A-USB Emulator
(5)
Section 3 Preparation before Use
When the following dialog box is displayed, setting up the emulator is completed.
Figure 3.30 Message for Completion of Setting up the Emulator
(6)
When setting up the emulator has been completed, the following message will be displayed.
Turn the setup switch (SW1) to ‘1’, connect the USB cable again, and click the [OK] button.
Figure 3.31 [License tool for H8S E10A-USB Emulator] Dialog Box
Notes: 1. Be sure to turn the setup switch (SW1) to ‘1’ except when the license tool for adding
device groups is used.
2. To use the license tool for another device group, in which the license has been installed
in the emulator, it is necessary to set up the firmware by using the setup tool or license
tool that corresponds to the device group. For details on the setup tool, refer to section
3.10, Setting up the Emulator, in this manual.
3. After you have added a device group by using the license tool, place the attached
device-group sticker onto the back of the emulator box. Otherwise, the emulator may
not be considered as a target product when repair is required. The license tool provides
a license to use the target device group. Be sure to acquire a license for each of the
E10A-USB emulators being used with that device group.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 39 of 190
H8S, H8SX Family E10A-USB Emulator
3.11
Section 3 Preparation before Use
System Check
When the software is executed, use the procedure below to check that the emulator is connected
correctly. Here, use the workspace for a tutorial provided on the product.
Refer to section 4, Preparations for Debugging, for the other activating method to create a new
project or use an existing workspace.
1. Connect the emulator to the host computer.
2. Connect the user system interface cable to the connector of the emulator.
3. Connect the user system interface cable to the user system connector.
4. Select [Renesas] -> [High-performance Embedded Workshop] -> [High-performance
Embedded Workshop] from [Programs] in the [Start] menu.
Figure 3.32 [Start] Menu
Note: The [High-performance Embedded Workshop] -> [Tools] is not displayed depending on
the user’s environment.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 40 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
5. The [Welcome!] dialog box is displayed.
Figure 3.33 [Welcome!] Dialog Box
[Create a new project workspace] radio button:
Creates a new workspace.
[Open a recent project workspace] radio button:
Uses an existing workspace and displays
the history of the opened workspace.
[Browse to another project workspace] radio button:
Uses an existing workspace; this radio
button is used when the history of the
opened workspace does not remain
To use a workspace for the tutorial, select the [Browse to another project workspace] radio button
and click the [OK] button.
When the [Open workspace] dialog box is opened, specify the following directory:
<Drive where the OS has been installed>:
\WorkSpace\Tutorial\E10A-USB\H8S\xxxx\Tutorial
Here, ‘xxxx’ means the target product group.
Note: When the H8SX product group is used, specify \E10A-USB\H8SX\xxxx\Tutorial. The
following explains the case of H8S.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 41 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
After the directory has been specified, select the following file and click the [Open] button.
Figure 3.34 [Open Workspace] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 42 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
6. The [Select Emulator mode] dialog box is displayed.
Figure 3.35 [Select Emulator mode] Dialog Box
Select the MCU name in use from the [Device] drop-down list box. The following items are
selected in the [Mode] group box.
⎯ E10A-USB Emulator
The E10A-USB emulator for the specified MCU is activated. Debugging the program is
enabled.
⎯ Program Flash
The user program is programmed to the internal flash memory. Debugging the program is
disabled. To download the load module, register it in the workspace.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 43 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
7. The [Connecting] dialog box is displayed and the emulator connection is started.
Figure 3.36 [Connecting] Dialog Box
8. The dialog box shown in figure 3.37 is displayed if no product groups have been installed in
the emulator at the time of purchase or if the H8S or H8SX license has been installed in the
emulator but the emulator firmware has been set up for a different device group. The dialog
box shown in figure 3.38 is displayed if an old version of the emulator firmware has been set
up in the emulator. Clicking the [OK] button sets up the emulator firmware.
Figure 3.37 Dialog Box to Confirm Setting up of the Emulator Firmware
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 44 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Figure 3.38 Dialog Box to Confirm Updating of the H8S Emulator Firmware
CAUTION
The USB cable must not be disconnected until writing is
complete.
Early disconnection may damage the emulator.
Note: The above dialog boxes are only displayed if you are using the HS0005KCU01H (serial
No.: 03311C or later) or HS0005KCU02H (serial No.: 04146E or later) emulator
hardware. In this case, follow the procedure described in section 3.10.1, Setting up at
Purchasing the Emulator or Updating the Version of Software.
9. The dialog box is displayed as shown in figure 3.39 or figure 3.40.
Figure 3.39 [Turn Power on] Message Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 45 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Figure 3.40 Dialog Box of the Power-on Request Message
10. Turn on the user system.
11. When using the H8S family, the dialog box shown in figure 3.41 is displayed. Input the system
clock value.
The system clock is the input clock.
Figure 3.41 [System Clock] Dialog Box
12. Set an eight-digit hexadecimal ID code as a security code for the flash memory. To read the
data that has been written to the internal flash memory, input this ID code when the [E10AUSB Emulator] is selected in the [Select Emulator mode] dialog box and the [New ID code]
check box is unselected on activating the emulator. If the ID code is not matched or the [New
ID code] check box is selected, the flash memory contents are erased.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 46 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Figure 3.42 [ID Code] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 47 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
13. When "Connected" is displayed in the [Output] window of the High-performance Embedded
Workshop, the emulator initiation is completed.
Figure 3.43 High-performance Embedded Workshop Window
Note: When the user program has already been downloaded to the flash memory, source-level
debugging cannot be executed because there is no debugging information on the user
program after the emulator has been activated. Be sure to load the debugging information
file. For details, refer to section 4.2.1, Setting at Emulator Activation.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 48 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
Notes: 1. If the user system interface cable is disconnected from the connector on the user
system, the following dialog box will appear.
Figure 3.44 [Cable disconnected from connector] Dialog Box
2. If the emulator is not properly initialized, one of the dialog boxes shown in figures 3.45
through 3.51 will appear.
(a) The following dialog box is displayed when the flash memory cannot be erased.
Exchange the MCU since the flash memory has been reprogrammed more times than
the limitation.
Figure 3.45 [Flash memory erase error!] Dialog Box
Note: If a mode is illegally set, the error message shown in above figure will be displayed.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 49 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
(b) The following dialog box is displayed when an incorrect ID code has been input. For
security, the flash memory is completely erased.
Figure 3.46 [ID code error!] Dialog Box
(c) The following dialog box is displayed when the MCU cannot communicate with the
emulator. The MCU may not operate correctly; check the MCU settings.
Figure 3.47 [Error H-UDI boot] Dialog Box
(d) If the following dialog box is displayed, check that the user system connector on the
user system is correctly connected.
Figure 3.48 [Check the connection] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 50 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
(e) If the following dialog box is displayed, the version of the firmware in the emulator
may be old. Set up the firmware by using the setup tool. For the usage of the setup
tool, refer to section 3.10, Setting up the Emulator.
Figure 3.49 [Emulator firmware error (3)] Dialog Box
(f) If the following dialog box is displayed, the version of the firmware in the emulator
may be old. Set up the firmware by using the setup tool.
Figure 3.50 [Emulator version error] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 51 of 190
H8S, H8SX Family E10A-USB Emulator
Section 3 Preparation before Use
(g) If the following dialog box is displayed, the MCU selected on activating the emulator
does not match the actual MCU. Select the correct MCU.
Figure 3.51 [MCU identification error] Dialog Box
3. If an incorrect driver has been selected, the following dialog box will appear.
Figure 3.52 [Driver Communications error] Dialog Box
Figure 3.53 [Driver Communications error] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 52 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
Section 4 Preparations for Debugging
4.1
Method for Activating High-performance Embedded Workshop
This section describes the ways to create and modify workspaces using H8S family (H8S/xxxx
E10A-USB SYSTEM). Replace ‘H8S/xxxx E10A-USB SYSTEM’ in the description (including
figures) as ‘H8SX/xxxx E10A-USB SYSTEM’ when you use H8SX family.
To activate the High-performance Embedded Workshop, follow the procedure listed below.
1. Connect the emulator to the host computer and the user system, then turn on the user system.
2. Select [High-performance Embedded Workshop] from [Renesas High-performance Embedded
Workshop] of [Programs] in the [Start] menu.
3. The [Welcome!] dialog box is displayed.
Figure 4.1 [Welcome!] Dialog Box
[Create a new project workspace] radio button:
Creates a new workspace.
[Open a recent project workspace] radio button:
Uses an existing workspace and displays
the history of the opened workspace.
[Browse to another project workspace] radio button:
Uses an existing workspace; this radio
button is used when the history of the
opened workspace does not remain.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 53 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
In this section, we describe the following three ways to start up the High-performance Embedded
Workshop:
• [Create a new project workspace] - a toolchain is not in use
• [Create a new project workspace] - a toolchain is in use
• [Browse to another project workspace]
The operation of [Open a recent project workspace] radio button is same as the operation without
specifying the workspace file when [Browse to another project workspace] is selected.
4.1.1
Creating the New Workspace (Toolchain Not Used)
1. In the [Welcome!] dialog box that is displayed when the High-performance Embedded
Workshop is activated, select [Create a new project workspace] radio button and click the
[OK] button.
Figure 4.2 [Welcome!] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 54 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
2. The Project Generator is started. In this section, we omit description of the settings for the
toolchain.
If you have not purchased the toolchain, the following dialog box is displayed.
Figure 4.3 [New Project Workspace] Dialog Box
[Workspace Name] edit box: Enter the new workspace name. Here, for example, enter ‘test’.
[Project Name] edit box:
Enter the project name. When the project name is the same as
the workspace name, it needs not be entered.
Other list boxes are used for setting the toolchain; the fixed information is displayed when the
toolchain has not been installed.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 55 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
3. The following dialog box is displayed.
Figure 4.4 [Debugger Target] Dialog Box
Check [H8S/xxxx E10A-USB SYSTEM] and click the [Next] button.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 56 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
4. Set the configuration file name. The configuration file saves the state of High-performance
Embedded Workshop except for the emulator.
Figure 4.5 [Debugger Options] Dialog Box
This is the end of the emulator setting.
Click the [Finish] button to exit the Project Generator. The High-performance Embedded
Workshop is activated.
5. After the High-performance Embedded Workshop has been activated, the emulator is
automatically connected. For operation during connection, refer to section 3.11, System
Check.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 57 of 190
H8S, H8SX Family E10A-USB Emulator
4.1.2
Section 4 Preparations for Debugging
Creating the New Workspace (Toolchain Used)
1. In the [Welcome!] dialog box that is displayed when the High-performance Embedded
Workshop is activated, select [Create a new project workspace] radio button and click the
[OK] button.
Figure 4.6 [Welcome!] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 58 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
2. The Project Generator is started.
If you have purchased the toolchain, the following dialog box is displayed.
Figure 4.7 [New Project Workspace] Dialog Box
[Workspace Name] edit box:
Enter the new workspace name. Here, for example, enter
‘test’.
[Project Name] edit box:
Enter the project name. When the project name is the
same as the workspace name, it needs not be entered.
[CPU family] drop-down list box: Select the target CPU family.
[Tool chain] drop-down list box:
Select the target toolchain name when using the toolchain.
Otherwise, select [None].
[Project type] list box:
Select the project type to be used.
Note: When [Demonstration] is selected in the emulator, note the following:
The [Demonstration] is a program for the simulator. When the generated program is used
by the emulator, delete the Printf statement.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 59 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
3. Make the required setting for the toolchain. When the setting has been completed, the
following dialog box is displayed.
Figure 4.8 [New Project -7/9- Setting the Target System for Debugging] Dialog Box
Check [H8S/xxxx E10A-USB SYSTEM] and click the [Next] button. Mark other products as
required.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 60 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
4. Set the configuration file name. The configuration file saves the state of High-performance
Embedded Workshop except for the emulator.
Figure 4.9 [New Project -8/9- Setting the Debugger Options] Dialog Box
This is the end of the emulator setting.
Exit the Project Generator according to the instructions on the screen. The High-performance
Embedded Workshop is activated.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 61 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
5. After the High-performance Embedded Workshop has been activated, connect the emulator.
However, it is not needed to connect the emulator immediately after the High-performance
Embedded Workshop has been activated.
To connect the emulator, use one of the methods (a) and (b) below. For operation during
connection, refer to section 3.11, System Check.
(a) Connecting the emulator after the setting at emulator activation
Select [Debug settings] from the [Debug] menu to open the [Debug Settings] dialog
box. It is possible to register the download module or the command chain that is
automatically executed at activation. For details on the [Debug Settings] dialog box,
refer to section 4.2, Setting at Emulator Activation.
After the [Debug Settings] dialog box has been set, when the dialog box is closed, the
emulator is connected.
(b) Connecting the emulator without the setting at emulator activation
The emulator can be easily connected by switching the session file that the setting for
the emulator use has been registered.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 62 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
Figure 4.10 Selecting the Session File
In the list box that is circled in figure 4.10, select the session file name including the character
string that has been set in the [Target name] text box in figure 4.9, [New Project -8/9- Setting the
Debugger Options] dialog box. The setting for using the emulator has been registered in this
session file.
After selected, the emulator is automatically connected.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 63 of 190
H8S, H8SX Family E10A-USB Emulator
4.1.3
Section 4 Preparations for Debugging
Selecting an Existing Workspace
1. In the [Welcome!] dialog box that is displayed when the High-performance Embedded
Workshop is activated, select [Browse to another project workspace] radio button and click the
[OK] button.
Figure 4.11 [Welcome!] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 64 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
2. The [Open Workspace] dialog box is displayed. Select a directory in which you have created a
workspace.
After that, select the workspace file (.hws) and press the [Open] button.
Figure 4.12 [Open Workspace] Dialog Box
Note: In figure 4.12, ‘xxxx’ means the name of the MCU.
3. This activates the High-performance Embedded Workshop and recovers the state of the
selected workspace at the time it was saved.
When the saved state information of the selected workspace includes connection to the
emulator, the emulator will automatically be connected. To connect the emulator when the
saved state information does not include connection to the emulator, refer to section 4.4,
Connecting the Emulator.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 65 of 190
H8S, H8SX Family E10A-USB Emulator
4.2
4.2.1
Section 4 Preparations for Debugging
Setting at Emulator Activation
Setting at Emulator Activation
A batch file of commands can be specified for automatic execution when the emulator is activated.
It is also possible to register multiple load modules to be downloaded. The registered load
modules are displayed on the workspace window.
1. Select [Debug Settings…] from the [Debug] menu to open the [Debug Settings] dialog box.
Figure 4.13 [Debug Settings] Dialog Box ([Target] Page)
2. Select the product name to be connected in the [Target] drop-down list box.
3. Select the format of the load module to be downloaded in the [Default Debug Format] dropdown list box, then register the corresponding download module in the [Download Modules]
list box.
Note: Here, no program has been downloaded. For downloading, refer to section 5.2,
Downloading a Program.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 66 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
4. Click the [Options] tab.
Figure 4.14 [Debug Settings] Dialog Box ([Options] Page)
The command batch file that is automatically executed at the specified timing is registered. The
following four timings can be specified:
• At connecting the emulator (At target connection)
• Immediately before downloading (Before download of modules)
• Immediately after downloading (After download of modules)
• Immediately after reset (After reset)
Specify the timing for executing the command batch file in the [Command batch file load timing]
drop-down list box. In addition, register the command batch file to be executed with the specified
timing in the [Command Line Batch Processing] list box.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 67 of 190
H8S, H8SX Family E10A-USB Emulator
4.2.2
Section 4 Preparations for Debugging
Downloading a Program
A download module is added under [Download modules] in the [Workspace] window.
Open the load module of [Download modules] in the [Workspace] window by clicking the righthand mouse button and select [Download module] to start downloading the module.
Figure 4.15 Download Menu of the [Workspace] Window ([Projects])
Notes: 1. When load modules are downloaded, select [Debug] -> [Download] -> [All DownLoad
Modules].
2. The emulator downloads programs to the MCU flash memory just before execution of
the user program.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 68 of 190
H8S, H8SX Family E10A-USB Emulator
4.2.3
Section 4 Preparations for Debugging
Setting the Program Flash Mode
The following describes the procedures when the emulator is used as the programming tool. The
load module to be downloaded to the new workspace is registered and programmed.
(a) Select the new project workspace.
Figure 4.16 [New Project Workspace] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 69 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
(b) Select the target MCU and click the [Finish] button.
Figure 4.17 [Setting the Target System for Debugging] Dialog Box
(c) The [Select Emulator mode] dialog box is displayed.
Figure 4.18 [Select Emulator mode] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 70 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
Select the [Program Flash] mode.
Note:
The contents to be displayed differ from each MCU. This is dedicated mode for each
MCU, and is incorporated in the internal ROM. This is not available for ROM-less
products. Normal debugging is not possible.
(d) If the dialog box shown below is displayed, turn on the target board and press the [OK]
button.
Figure 4.19 [Turn Power on] Message Box
Figure 4.20 Dialog Box of the Reset Request Message
(e) Input the system clock value.
Figure 4.21 [System Clock] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 71 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
(f) Select [Debug Setting] from the [Debug] menu.
Figure 4.22 High-performance Embedded Workshop Window
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 72 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
(g) Select the download module with the [Add…] button.
Figure 4.23 [Debug Settings] Dialog Box ([Target] Page)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 73 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
(h) The download file is displayed on [Projects].
Figure 4.24 [Workspace] Window ([Projects])
(i) Select and download the file with the right-hand mouse button.
Figure 4.25 Download Menu of the [Workspace] Window ([Projects])
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 74 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
(j) The dialog box for sum checking is displayed and programming is completed. Checksum is
a value that data in the internal ROM area has been added by byte. If no user program
exists, the value is calculated by H’FF.
Figure 4.26 Message for Completion of Flash Memory Programming
(k) When the following dialog box is displayed, close and restart or exit the workspace.
To write the same data to the MCU continuously, select [Debug -> Initialize…] and go
back to step (c) (displaying [Select Emulator mode]). To exit, close the workspace.
Figure 4.27 Message for Restarting or Exiting Program Flash Mode
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 75 of 190
H8S, H8SX Family E10A-USB Emulator
4.3
Section 4 Preparations for Debugging
Debug Sessions
The High-performance Embedded Workshop stores all of your builder options into a
configuration. In a similar way, the High-performance Embedded Workshop stores your debugger
options in a session. The debugging platforms, the programs to be downloaded, and each
debugging platform’s options can be stored in a session.
Sessions are not directly related to a configuration. This means that multiple sessions can share
the same download module and avoid unnecessary program rebuilds.
Each session’s data should be stored in a separate file in the High-performance Embedded
Workshop project. Debug sessions are described in detail below.
4.3.1
Selecting a Session
The current session can be selected in the following two ways:
• From the toolbar
Select a session from the drop-down list box (figure 4.28) in the toolbar.
Figure 4.28 Toolbar Selection
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 76 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
• From the dialog box
1. Select [Debug -> Debug Sessions…]. This will open the [Debug Sessions] dialog box
(figure 4.29).
Figure 4.29 [Debug Sessions] Dialog Box
2. Select the session you want to use from the [Current session] drop-down list.
3. Click the [OK] button to set the session.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 77 of 190
H8S, H8SX Family E10A-USB Emulator
4.3.2
Section 4 Preparations for Debugging
Adding and Removing Sessions
A new session can be added by copying settings from another session or removing a session.
• To add a new empty session
1. Select [Debug -> Debug Sessions…] to display the [Debug Sessions] dialog box (figure
4.29).
2. Click the [Add…] button to display the [Add new session] dialog box (figure 4.30).
3. Check the [Add new session] radio button.
4. Enter a name for the session.
5. Click the [OK] button to close the [Debug Sessions] dialog box.
6. This creates a file with the name entered in step 4. If a file with this name already exists,
an error is displayed.
Figure 4.30 [Add new session] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 78 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
• To import an existing session into a new session file
1. Select [Debug -> Debug Sessions…] to display the [Debug Sessions] dialog box (figure
4.29).
2. Click the [Add…] button to display the [Add new session] dialog box (figure 4.30).
3. Check the [Use an existing session file] radio button.
4. Enter a name for the session.
5. Enter the name of an existing session file that you would like to import into the existing
project or click the [Browse] button to select the file location.
If the [Open and maintain link to session file] check box is not checked, the imported new
session file is generated in the project directory.
If the [Open and maintain link to session file] check box is checked, a new session file is
not generated in the project directory but is linked to the existing session file.
If the [Make session file link read only] check box is checked, the linked session file is
used as read-only.
6. Click the [OK] button to close the [Debug Sessions] dialog box.
• To remove a session
1. Select [Debug -> Debug Sessions…] to display the [Debug Sessions] dialog box (figure
4.29).
2. Select the session you would like to remove.
3. Click the [Remove] button.
Note that the current session cannot be removed.
4. Click the [OK] button to close the [Debug Sessions] dialog box.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 79 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
• To view the session properties
1. Select [Debug -> Debug Sessions…] to display the [Debug Sessions] dialog box (figure
4.29).
2. Select the session you would like to view the properties for.
3. Click the [Properties] button to display the [Session Properties] dialog box (figure 4.31).
Figure 4.31 [Session Properties] Dialog Box
• To make a session read-only
1. Select [Debug -> Debug Sessions…] to display the [Debug Sessions] dialog box (figure
4.29).
2. Select the session you would like to make read-only.
3. Click the [Properties] button to display the [Session Properties] dialog box (figure 4.31).
4. Check the [Read only] check box to make the link read-only. This is useful if you are
sharing debugger-setting files and you do not want data to be modified accidentally.
5. Click the [OK] button.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 80 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
• To save a session with a different name
1. Select [Debug -> Debug Sessions…] to display the [Debug Sessions] dialog box (figure
4.29).
2. Select the session you would like to save.
3. Click the [Save as…] button to display the [Save Session] dialog box (figure 4.32).
4. Specify the location to save the new file.
5. If you want to export the session file to another location, leave the [Maintain link] check
box unchecked. If you would like the High-performance Embedded Workshop to use this
location instead of the current session location, check the [Maintain link] check box.
6. Click the [Save] button.
Figure 4.32 [Save Session] Dialog Box
4.3.3
Saving Session Information
To save a session
Select [File -> Save Session].
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 81 of 190
H8S, H8SX Family E10A-USB Emulator
4.4
Section 4 Preparations for Debugging
Connecting the Emulator
Select either of the following two ways to connect the emulator:
(1) Connecting the emulator after the setting at emulator activation
Select [Debug settings] from the [Debug] menu to open the [Debug Settings] dialog box. It is
possible to register the download module or the command batch file that is automatically
executed at activation. For details on the [Debug Settings] dialog box, refer to section 4.2,
Setting at Emulator Activation.
When the dialog box is closed after setting the [Debug Settings] dialog box, the emulator will
automatically be connected.
(2) Connecting the emulator without the setting at emulator activation
Connect the emulator by simply switching the session file to one in which the setting for the
emulator use has been registered.
Figure 4.33 Selecting the Session File
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 82 of 190
H8S, H8SX Family E10A-USB Emulator
Section 4 Preparations for Debugging
In the list box that is circled in figure 4.33, select the session file name including the character
string that has been set in the [Target name] text box in figure 4.9, [New Project -8/9- Setting the
Debugger Options] dialog box. The setting for using the emulator has been registered in this
session file.
After the session file name is selected, the emulator will automatically be connected. For details
on the session file, refer to section 4.3, Debug Sessions.
4.5
Reconnecting the Emulator
When the emulator is disconnected, use the following way for reconnection:
Select [Debug -> Connect] or click the [Connect] toolbar button (
). The emulator is connected.
Note: The emulator must be selected in the [Target] drop-down list box of the [Debug Settings]
dialog box that is opened by selecting [Debug settings] from the [Debug] menu (see 4.2.1,
Setting at Emulator Activation).
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 83 of 190
H8S, H8SX Family E10A-USB Emulator
4.6
Section 4 Preparations for Debugging
Ending the Emulator
When using the toolchain, the emulator can be exited by using the following two methods:
•
Canceling the connection of the emulator being activated
•
Exiting the High-performance Embedded Workshop
(1) Canceling the connection of the emulator being activated
Select [Disconnect] from the [Debug] menu or click the [Disconnect] toolbar button (
).
(2) Exiting the High-performance Embedded Workshop
Select [Exit] from the [File] menu.
A message box may be displayed. If necessary, click the [Yes] button to save a session. After
saving a session, the High-performance Embedded Workshop exits. If not necessary, click the
[No] button to exit the High-performance Embedded Workshop.
Figure 4.34 [Session has been modified] Message Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 84 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Section 5 Debugging
This section describes the debugging operations and their related windows and dialog boxes.
5.1
5.1.1
Setting the Environment for Emulation
Opening the [Configuration] Dialog Box
Selecting [Options -> Emulator -> System…] or clicking the [Emulator System] toolbar button
( ) opens the [Configuration] dialog box.
5.1.2
[Emulator] Page
Sets the emulator operation conditions.
Figure 5.1 [Configuration] Dialog Box ([General] Page)
Note: The contents to be displayed differ depending on the MCU.
Items that can be displayed in the sheet are listed below.
Note: The items to be set differ between H8S, H8SX family and MCUs. For functions to be set
in each MCU, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 85 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
[Device] combo box
Displays the MCU name.
[Emulation mode] combo box
Selects the emulation mode at user program execution.
[Step option] combo box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
•
Normal:
Performs normal emulation.
•
No break:
Temporarily disables breakpoint settings and executes user
program.
•
Sequential Break Condition 2-1 :
Program is halted when Break Condition 2 and Break
Condition 1 are satisfied in that order.
•
Sequential Break Condition 3-2-1 :
Program is halted when Break Condition 3, Break Condition
2, and Break Condition 1 are satisfied in that order.
•
Sequential Break Condition 4-3-2-1 :
Program is halted when Break Condition 4, Break Condition
3, Break Condition 2, and Break Condition 1 are satisfied in
that order.
*1
*1
*1
Enables or disables interrupts during step operation.
•
Disables interrupts during single step execution:
Interrupts during step operation are masked.
•
Enables interrupts during single step execution:
Interrupts during step operation are released.
Page 86 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
*2
[JTAG clock] combo box
Sets the frequency of the JTAG clock.
[Flash memory synchronization]
combo box
Selects whether or not the contents of the flash memory are
acquired by the emulator when the user program is stopped or
the position where the PC break is set is put back as the
original code.
When the flash memory is not reprogrammed by the user
program, its contents need not be acquired by the emulator.
If there is no problem with the state that the program in the
flash memory has been replaced as the PC break code, the
position where the PC break is set needs not be put back as
the original code.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
•
Disable:
Read or program is not performed for the flash memory
except when the emulator is activated, the flash memory
area is modified, and the settings of the PC break to the
flash memory area are changed.
•
PC to flash memory:
When the user program is stopped, the specified PC break
code is replaced as the original instruction. Select this
option if there is a problem with the state that the program in
the flash memory has been replaced as the PC break code.
•
Flash memory to PC:
When the user program is stopped, the contents of the flash
memory are read by the emulator. Select this option if the
flash memory is reprogrammed by the user program.
•
PC to flash memory, Flash memory to PC:
When the user program is stopped, the contents of the flash
memory are read by the emulator and the specified PC
break code is replaced as the original instruction. Select this
option if the flash memory is reprogrammed by the user
program and there is a problem with the state that the
program in the flash memory has been replaced as the PC
break code.
Page 87 of 190
H8S, H8SX Family E10A-USB Emulator
[Step Over option] combo box
[Flash memory write after
download] group box
[Parallel] group box
[Short break] group box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Section 5 Debugging
Enables or disables programming of the flash memory while
executing step operation.
•
Programming of the flash memory:
Uses a software break for step operation (e.g. Step Over)
and enables programming of the flash memory.
•
No Programming of the flash memory:
Uses Break Condition for step operation (e.g. Step Over)
*3
and disables programming of the flash memory.
Enables or disables programming of the flash memory after
downloading the program.
•
Disable:
Disables programming of the flash memory after
downloading the program.
•
Enable:
Enables programming of the flash memory after
downloading the program.
Selects the setting of memory access during user program
*1
execution.
•
Disable:
Uses no emulator debugging functions to access memory.
A short break will occur.
•
Enable:
Uses emulator debugging functions to access memory.
Selects whether or not memory should be accessed during user
*4
program execution.
•
Disable:
Disables access to memory during user program execution.
•
Enable:
Enables access to memory during user program execution.
Page 88 of 190
H8S, H8SX Family E10A-USB Emulator
[Memory access] group box
Section 5 Debugging
Selects whether or not memory should be accessed during user
*1
program execution.
•
Disable:
Disables access to memory during user program execution.
•
Enable:
Enables access to memory during user program execution.
Notes: 1. This function is supported by the H8SX family.
2. The range of frequency for the JTAG clock differs depending on the supported MCU.
3. The H8S family supports the optional Step Over function. When Step Over is
performed after selecting [No Programming of the flash memory] for [Step Over
option], the instruction that follows a JSR, BSR, or TRAPA instruction will also be
executed. If there are consecutive JSR, BSR, or TRAPA instructions, execution
proceeds until it reaches an instruction that is not JSR, BSR, or TRAPA. (When there
are consecutive function calls in C language, the program steps all of these functions.)
4. This function is supported by the H8S family.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 89 of 190
H8S, H8SX Family E10A-USB Emulator
5.2
Section 5 Debugging
Downloading a Program
This section describes how to download a program and view it as source code or assemblylanguage mnemonics.
Note: After a break has been detected, the High-performance Embedded Workshop displays the
location of the program counter (PC). In most cases, for example if an Elf/Dwarf2-based
project is moved from its original path, the source file may not be automatically found. In
this case, the High-performance Embedded Workshop will open a source file browser
dialog box to allow you to manually locate the file.
5.2.1
Downloading a Program
A load module to be debugged must be downloaded.
To download a program, select the load module from [Debug -> Download] or select [Download]
from the popup menu opened by clicking the right-hand mouse button on the load module in
[Download modules] of the [Workspace] window.
Note: Before downloading a program, it must be registered to the High-performance Embedded
Workshop as a load module. For registration, refer to section 4.2, Setting at Emulator
Activation.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 90 of 190
H8S, H8SX Family E10A-USB Emulator
5.2.2
Section 5 Debugging
Viewing the Source Code
Select a source file name in the [Workspace] window and click [Open] in the popup menu to make
the High-performance Embedded Workshop display the source file in the editor. It is also possible
to display your source files by double-clicking on their names in the [Workspace] window.
Figure 5.2 [Editor] Window
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 91 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
In this window, the following items are shown on the left as line information.
The first column (Line number column): Source-line information
The second column (Source address column): Address information
The third column (Event column): Event information (break condition)
The fourth column (S/W breakpoint column): PC, bookmark, and breakpoint information
Line number column
The line number that corresponds to the source file is displayed.
Source address column
When a program is downloaded, an address for the current source file is displayed on the Source
address column. These addresses are helpful when setting the PC value or a breakpoint.
Event column
The Event column displays the following item:
: An address condition as a break condition; only one such a position can be set.
This is also set by using the popup menu.
The bitmap symbol above is shown by double-clicking the Event column. This is also set by using
the popup menu.
Figure 5.3 Popup Menu
Notes: 1. The contents of the Event column are erased when conditions other than the address
condition are added to each channel by using the [Edit] menu or in the [Event] window.
2. The conditions for setting the break condition differ depending on the MCU. For
details, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 92 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
S/W breakpoint column
S/W breakpoint column displays the following items:
: A bookmark is set.
: A breakpoint is set.
: PC location
To switch off a column in all source files
1. Click the right-hand mouse button on the [Editor] window or select the [Edit] menu.
2. Click the [Define Column Format…] menu item.
3. The [Global Editor Column States] dialog box is displayed.
4. A check box indicates whether the column is enabled or not. If it is checked, the column is
enabled. If the check box is gray, the column is enabled in some files and disabled in
others. Deselect the check box of a column you want to switch off.
5. Click the [OK] button for the new column settings to take effect.
Figure 5.4 [Global Editor Column States] Dialog Box
To switch off a column in one source file
1. Open the source file which contains the column you want to remove and right-click on the
[Edit] window.
2. Click the [Columns] menu item to display a cascaded menu item. The columns are
displayed in this popup menu. If a column is enabled, it has a tick mark next to its name.
Clicking the entry will toggle whether the column is displayed or not.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 93 of 190
H8S, H8SX Family E10A-USB Emulator
5.2.3
Section 5 Debugging
Viewing the Assembly-Language Code
If there is an address at the cursor position in the [Editor] window, selecting [Go to Disassembly]
in the pop-up menu opens the [Disassembly] window.
The first address displayed in the [Disassembly] window is the address where the cursor is placed
in the [Editor] window.
If you do not have a source file, but wish to view code in the assembly-language level, either
choose [View] -> [Disassembly…] or click on the [Disassembly] window’s toolbar button ( ).
The [Disassembly] window opens at the current PC location and shows [Address] and [Code]
(optional) which show the disassembled mnemonics (with labels when available).
Selecting the [Mixed display] toolbar button (
following shows an example in this case.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
) displays both the source and the code. The
Page 94 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Figure 5.5 [Disassembly] Window
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 95 of 190
H8S, H8SX Family E10A-USB Emulator
5.2.4
Section 5 Debugging
Modifying the Assembly-Language Code
You can modify the assembly-language code by double-clicking on the instruction that you want
to change. The [Assembler] dialog box will be opened.
Figure 5.6 [Assembler] Dialog Box
The address, instruction code, and mnemonic are displayed. Enter the new instruction or edit the
old instruction in the [Mnemonics] field. Pressing the [Enter] key will replace the memory content
with the new instruction and move on to the next instruction. Clicking the [OK] button will
replace the memory content with the new instruction and close the dialog box. Clicking the
[Cancel] button or pressing the [Esc] key will close the dialog box without modifying the memory
contents.
Note: The assembly-language code being displayed is the current memory content. If the
memory contents are changed the [Assembler] dialog box and the [Disassembly] window
will show the new assembly-language code, but the source file displayed in the [Editor]
window will be unchanged. This is the same even if the source file contains assembly
codes.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 96 of 190
H8S, H8SX Family E10A-USB Emulator
5.2.5
Section 5 Debugging
Viewing a Specific Address
When you are viewing your program in the [Disassembly] window, you may wish to look at
another area of your program's code. Rather than scrolling through a lot of code in the program,
you can go directly to a specific address. Select [Set Address…] from the popup menu, and the
dialog box shown in figure 5.7 is displayed.
Figure 5.7 [Set Address] Dialog Box
Enter the address in the [Address] edit box and either click on the [OK] button or press the [Enter]
key. A label name can also be specified as the address. The [Disassembly] window will be updated
to show the code at the new address. When an overloaded function or a class name is entered, the
[Select Function] dialog box opens for you to select a function.
5.2.6
Viewing the Current Program Counter Address
Wherever you can enter an address or value into the High-performance Embedded Workshop, you
can also enter an expression. If you enter a register name prefixed by the hash character (#), the
contents of that register will be used as the value in the expression. Therefore, if you enter the
expression #pc in the [Set Address] dialog box, the [Editor] or [Disassembly] window will display
the current PC address. It also allows the offset of the current PC to be displayed by entering an
expression with the PC register plus an offset, e.g., #PC+0x100.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 97 of 190
H8S, H8SX Family E10A-USB Emulator
5.3
Section 5 Debugging
Using the Event Points
The emulator has the event point function that performs breaking by specifying higher-level
conditions along with the PC breakpoints standard for the High-performance Embedded
Workshop.
5.3.1
PC Breakpoints
When the instruction of the specified address is fetched, the user program is stopped. Up to 255
points can be set.
5.3.2
Break Conditions
Break conditions can be used for higher-level conditions such as the data condition as well as
specification of the single address.
5.3.3
Opening the [Event] Window
Select [View -> Code -> Eventpoints] or click the [Eventpoints] toolbar button (
[Event] window.
) to open the
The [Event] window has the following two sheets:
[Breakpoint] sheet:
Displays the settings made for PC breakpoints. It is also possible to set,
modify, and cancel PC breakpoints.
[Breakcondition] sheet:
Displays or sets the settings made for break condition channels.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 98 of 190
H8S, H8SX Family E10A-USB Emulator
5.3.4
Section 5 Debugging
Setting PC Breakpoints
It is possible to display, modify, and add PC breakpoints on the [Breakpoint] sheet.
Figure 5.8 [Event] Window ([Breakpoint] Sheet)
This window displays and sets the breakpoints. Items that can be displayed in the sheet are listed
below.
[Type]
Breakpoint
[State]
Whether the breakpoint is enabled or disabled
[Condition] An address that the breakpoint is set
Address = Program counter (Corresponding file name, line, and symbol name)
[Action]
Operation of the emulator when a break condition is satisfied
Break: Breaks program execution
When a breakpoint is double-clicked in this window, the [Set Break] dialog box is opened and
break conditions can be modified.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 99 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
A popup menu containing the following options is available by right-clicking within the window.
5.3.5
Add
Sets breakpoints. Clicking this item will open the [Set Break] dialog box and break conditions can
be specified.
5.3.6
Edit
Only enabled when one breakpoint is selected. Select a breakpoint to be edited and click this item.
The [Set Break] dialog box will open and break conditions can be changed.
5.3.7
Enable
Enables the selected breakpoint(s).
5.3.8
Disable
Disables the selected breakpoint(s). When a breakpoint is disabled, the breakpoint will remain in
the list; when specified conditions have been satisfied, a break will not occur.
5.3.9
Delete
Removes the selected breakpoint. To retain the details of the breakpoint but not have it cause a
break when its conditions are met, use the Disable option (see section 5.3.8, Disable).
5.3.10
Delete All
Removes all breakpoints.
5.3.11
Go to Source
Only enabled when one breakpoint is selected. Opens the [Editor] window at the address of the
breakpoint.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 100 of 190
H8S, H8SX Family E10A-USB Emulator
5.3.12
Section 5 Debugging
[Set Break] Dialog Box
Figure 5.9 [Set Break] Dialog Box
This dialog box specifies break conditions.
A breakpoint address to be set is specified in the [Address] edit box. The PC register can also be
specified such as #PC. Up to 255 breakpoints can be specified.
The contents to be set differ depending on the product. For details, refer to the on-line help for
each product.
When [Address] is selected, if an overloaded function or class name including a member function
is specified in address, the [Select Function] dialog box opens.
Clicking the [OK] button sets the break conditions. Clicking the [Cancel] button closes this dialog
box without setting the break conditions.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 101 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Notes on Setting the [Set Break] Dialog Box
1. When an odd address is set, the address is rounded down to an even address.
2. A software break is accomplished by replacing instructions. Accordingly, it can be set only to
the flash memory or RAM area. However, a software break cannot be set to the following
addresses:
⎯ An area other than the flash memory or RAM
⎯ An area occupied by the E10A-USB emulator program
⎯ An instruction in which Break Condition 1 is satisfied
3. During step execution, a software breakpoint is disabled.
4. A condition set at Break Condition 1 is disabled immediately after starting execution when an
instruction at a software breakpoint is executed. A break does not occur even if a condition of
Break Condition 1 is satisfied immediately after starting the execution.
5. When execution resumes from the breakpoint address after the program execution stops at the
software breakpoint, single-step execution is performed at the address before execution
resumes. Therefore, realtime operation cannot be performed.
6. Settings of software breakpoint and Break Condition 1 are invalid while the STEP OVER
function is being used.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 102 of 190
H8S, H8SX Family E10A-USB Emulator
5.3.13
Section 5 Debugging
Setting Break Conditions
On the [Breakcondition] sheet, the settings for break conditions are displayed, modified, and
added.
Figure 5.10 [Event] Window ([Breakcondition] Sheet)
Note: The items that can be set in this window differ depending on the product. For details on
the settings for each product, refer to the online help.
This window displays and sets the break condition.
Notes on Setting the Break Condition:
1. When [Step In], [Step Over], or [Step Out] is selected, the settings of Break Condition 1 are
disabled.
2. Setting of Break Condition 1 is disabled when an instruction to which a BREAKPOINT has
been set is executed.
3. When step over function is used, the settings of BREAKPOINT and Break Condition 1 are
disabled.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 103 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Items that can be displayed in the sheet are listed below.
[Type]
Break channel number
[State]
Whether the breakpoint is enabled or disabled
[Condition] A condition that satisfies a break
[Action]
Operation of the emulator when a break condition is satisfied
Break: Breaks program execution
When a Break condition 1 is double-clicked in this window, the [Break condition 1] dialog box is
opened and break conditions can be modified. For details on the [Break condition 1] dialog box,
refer to the online help for each product.
A popup menu containing the following options is available by right-clicking within the window.
5.3.14
Edit...
Only enabled when one break channel is selected. Select a break channel to be edited and click
this item. The [Break condition 1] dialog box will open and break conditions can be changed.
5.3.15
Enable
Enables the selected break channel(s). A break channel that the condition has not been set is not
enabled.
5.3.16
Disable
Disables the selected break channel(s). When a break channel is disabled, a break will not occur
even if specified conditions have been satisfied.
5.3.17
Delete
Initializes the condition of the selected break channel. To retain the details of the break channel
but not have it cause a break when its conditions are met, use the Disable option (see section
5.3.16, Disable).
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 104 of 190
H8S, H8SX Family E10A-USB Emulator
5.3.18
Section 5 Debugging
Delete All
Initializes conditions of all break channels.
5.3.19
Go to Source
Only enabled when one break channel is selected. Opens the [Editor] window at address of break
channel.
If an address value has not been set to the break channel, this option cannot be used.
5.3.20
Sequential Conditions
Sets the sequential condition of the break channel.
Note: This function is set in [Emulation mode] of the [Configuration] dialog box (refer to section
5.1.2, [Emulator] Page).
5.3.21
Editing Break Conditions
Handlings for settings other than PC breakpoints and break conditions are common. The following
describes examples of such handling.
5.3.22
Modifying Break Conditions
Select a break condition to be modified, and choose [Edit...] from the popup menu to open the
dialog box for the event, which allows the user to modify the break conditions. The [Edit...] menu
is only available when one break condition is selected.
5.3.23
Enabling Break Conditions
Select a break condition and choose [Enable] from the popup menu to enable the selected break
condition.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 105 of 190
H8S, H8SX Family E10A-USB Emulator
5.3.24
Section 5 Debugging
Disabling Break Conditions
Select a break condition and choose [Disable] from the popup menu to disable the selected break
condition. When a break condition is disabled, the break condition will remain in the list, but an
event will not occur when the specified conditions have been satisfied.
5.3.25
Deleting Break Conditions
Select a break condition and choose [Delete] from the popup menu to remove the selected break
condition. To retain the break condition but not have it cause an event when its conditions are met,
use the [Disable] option (see section 5.3.24, Disabling Break Conditions).
5.3.26
Deleting All Break Conditions
Choose [Delete All] from the popup menu to remove all break conditions.
5.3.27
Viewing the Source Line for Break Conditions
Select a break condition and choose [Go to Source] from the popup menu to open the [Editor] or
[Disassembly] window at the address of the break condition. The [Go to Source] menu is only
available when break conditions that have the corresponding source file are selected.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 106 of 190
H8S, H8SX Family E10A-USB Emulator
5.3.28
Section 5 Debugging
[Break condition 1] Dialog Box
Figure 5.11 [Break condition 1] Dialog Box (H8S)
This page sets the address bus, data bus, and read/write cycle conditions.
Note: The items that can be set in this dialog box differ depending on the MCU. For details on
the settings for each MCU, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 107 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
The [Address] group box sets address bus conditions.
Option
Description
[Don’t care] check box
Does not set address conditions.
[Address] radio button
Sets the use of the normal address bus as break
conditions.
[Only program fetched address after]
radio button
Sets a break after prefetched address execution as break
conditions.
[Address] edit box
Sets the address bus value with a number or a symbol.
[Mask] edit box
After the radix has been set as ″H″ (hexadecimal) or ″B″
(binary), the setting ″∗′″ selects masking of the
corresponding digit.
The contents of an option that can be will change depending on the radio button selected.
Option
Description
[Address] radio button
All options can be set.
[Only program fetched address after]
radio button
The [Address] option can be set.
The [Data] group box sets the data bus conditions.
Option
Description
[Don’t care] check box
No data conditions are set.
[Value] edit box
Sets the data bus with a number.
[Low byte] radio button
Sets data access size as the lower 8-bit access.
[High byte] radio button
Sets data access size as the upper 8-bit access.
[Word] radio button
Sets data access size as the word access.
The [Read/Write] group box sets the read/write cycle conditions.
Option
Description
[Read/Write] radio button
Sets the read/write cycle conditions as break conditions.
[Read] radio button
Sets read cycles as break conditions.
[Write] radio button
Sets write cycles as break conditions.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 108 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Figure 5.12 [Break condition 1] Dialog Box (H8SX)
This page sets the address bus, data bus, and read/write cycle conditions.
Note: The items that can be set in this dialog box differ depending on the MCU. For details on
the settings for each MCU, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 109 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
The [Address] group box sets address bus conditions.
Option
Description
[Don’t care] check box
Does not set address conditions.
[Address] radio button
Sets the use of the normal address bus as break
conditions.
[Only program fetched address] radio
button
Sets a break before prefetched address execution as
break conditions.
[Only program fetched address after]
radio button
Sets a break after prefetched address execution as break
conditions.
[Address] edit box
Sets the address bus value with a number or a symbol.
[Non user mask] radio button
Does not set mask conditions.
[User mask] radio button
Sets mask conditions.
[Mask] edit box
Sets a value to be masked when [User mask] is selected.
For masked bits, the break condition is satisfied for any
values.
The contents of an option that can be changed depending on the radio button selected.
Option
Description
[Address] radio button
All options can be set.
[Only program fetched address] radio
button
The [Address] and [Count] options can be set.
[Only program fetched address after]
radio button
The [Address] and [Count] options can be set.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 110 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
The [Data] group box sets the data bus conditions.
Option
Description
[Don’t care] check box
No data conditions are set.
[Value] edit box
Sets the data bus with a number.
[Byte] radio button
Sets byte data access cycles.
[Word] radio button
Sets word data access cycles.
[Long] radio button
Sets longword data access cycles.
[Non user mask] radio button
Does not set mask conditions.
[Mask enabled] radio button
Sets mask conditions.
[Mask] edit box
Sets a value to be masked when [Mask enabled] is
selected. For masked bits, the break condition is
satisfied for any values.
The [Bus state] group box sets the bus state conditions.
Option
Description
[Data] check box
Sets the execution cycle as break conditions.
[Dtc] check box
Specifies DTC cycle as break conditions.
[Dma] check box
Specifies DMA cycle as break conditions.
The [Read/Write] group box sets the read/write cycle conditions.
Option
Description
[Read/Write] radio button
Sets the read/write cycle conditions as break conditions.
[Read] radio button
Sets read cycles as break conditions.
[Write] radio button
Sets write cycles as break conditions.
The [Count] group box sets the break condition satisfaction conditions.
Option
Description
[Don’t care] check box
Sets no satisfaction count conditions.
[Numbers] edit box
Sets the satisfaction count as a break condition. The
maximum count is 65,535. Breaks when the conditions
set by the [Break Condition] dialog box for the specified
times are satisfied. The default is H'1.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 111 of 190
H8S, H8SX Family E10A-USB Emulator
5.4
Section 5 Debugging
Viewing the Trace Information
For the description on the trace function, refer to section 2.2, Trace Functions.
5.4.1
Opening the [Trace] Window
To open the [Trace] window, choose [View -> Code -> Trace] or click the [Trace] toolbar button
( ).
5.4.2
Acquiring Trace Information
The acquired trace information is displayed in the [Trace] window. The four-channel branchsource addresses are displayed in H8 family. The eight-channel branch-source or branchdestination addresses are displayed in H8SX family.
Figure 5.13 [Trace] Window (H8S)
Figure 5.14 [Trace] Window (H8SX)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 112 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
This window displays the following trace information items:
[PTR]
Pointer to a location in the trace buffer (+0 for the last executed instruction)
[IP]
The amount of acquired trace information
[Type]
Type of branch:
BRANCH: branch source
DESTINATION: branch destination
[Address]
Instruction address
[Instruction]
Instruction mnemonic
[Source]
The C/C++ or assembly-language source program
[Label]
Label information
It is possible to hide any column not necessary in the [Trace] window. Selecting a column you
want to hide from the popup menu displayed by clicking the right-hand mouse button on the
header column hides that column. To display the hidden column, select the column from the said
popup menu again.
Note: The number of branch instructions that can be acquired by a trace and the trace display
differ depending on the product. For details on the specifications of each product, refer to
the online help.
5.4.3
Clearing the Trace Information
When [Clear] is selected from the popup menu, the trace buffer that stores the trace information
becomes empty. If several [Trace] windows are open, all [Trace] windows will be cleared as they
all access the same buffer.
5.4.4
Saving the Trace Information in a File
Select [Save...] from the popup menu to open the [Save As] file dialog box, which allows the user
to save the information displayed in the [Trace] window as a text file. A range can be specified
based on the [PTR] number. Note that this file cannot be reloaded into the [Trace] window.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 113 of 190
H8S, H8SX Family E10A-USB Emulator
5.4.5
Section 5 Debugging
Viewing the [Editor] Window
The [Editor] window corresponding to the selected trace record can be displayed in the following
two ways:
• Select a trace record and choose [View Source] from the popup menu.
• Double-click a trace record
The [Editor] or [Disassembly] window opens and the selected line is marked with a cursor.
5.4.6
Trimming the Source
Choose [Trim Source] from the popup menu to remove the white space from the left side of the
source.
When the white space is removed, a check mark is shown to the left of the [Trim Source] menu.
To restore the white space, choose [Trim Source] while the check mark is shown.
5.5
Using the Start/Stop Function
The start/stop functions are useful if you wish to control the user system in synchronization with
the user program execution being started or stopped.
5.5.1
Opening the [Start/Stop Function Setting] Dialog Box
The start/stop functions are useful if you wish to control the user system in synchronization with
the user program execution being started or stopped. To open the [Start/Stop Function Setting]
dialog box, select [Setup -> Emulator -> Start/Stop Function Setting] or click on the [Start/Stop
Function dialog box] toolbar button ( ).
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 114 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Figure 5.15 [Start/Stop Function Setting] Dialog Box
The [Start/Stop Function Setting] dialog box contains the following options.
[Run the specified routine
just before the user program
execution is started.]
checkbox :
Select this box if you wish to run a user routine just before the
user program execution is started.
[Run the specified routine
just after the user program
execution is stopped.]
checkbox :
Select this box if you wish to run a user routine just after the
user program execution is stopped.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
[Start address]:
[Start address]:
Specify an address where a routine
will start to run just before the user
program execution is started. You
can also specify a label.
Specify an address where a routine
will start to run just after the user
program execution is stopped. You
can also specify a label.
Page 115 of 190
H8S, H8SX Family E10A-USB Emulator
5.5.2
Section 5 Debugging
Specifying the Routine to be Executed
It is possible to specify the respective routines immediately before starting and immediately after
halting the user program execution.
When the [The specified routine is executed immediately before execution of the user’s program.]
check box is selected, the routine specified in the [starting address] combo box, which is below
this check box, is executed immediately before starting user program execution.
If no specified routine is executed immediately before starting user program execution, do not
select the [The specified routine is executed immediately before execution of the user’s program.]
check box.
When the [The specified routine is executed immediately after execution of the user’s program.]
check box is selected, the routine specified in the [starting address] combo box, which is below
this check box, is executed immediately after stopping user program execution.
If no specified routine is executed immediately before starting user program execution, do not
select the [The specified routine is executed immediately after execution of the user’s program.]
check box.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 116 of 190
H8S, H8SX Family E10A-USB Emulator
5.5.3
Section 5 Debugging
Restrictions on the Start/Stop Function
The start/stop function has the following restrictions.
• An RTS instruction must be written at the end of the user routine.
• The user routine must end.
• No break should occur within the user routine.
• No interrupt should be accepted in the user routine.
•
The user routine to run immediately before the user program execution must end within 2
msec.
• The user routine to run after the user program execution is stopped must end within 30 sec.
•
As the stack area for the routine specified for execution before the user program starts, use
the firmware stack of the emulator. The stack area is no larger than H’80 bytes.
•
The user stack should be used by the routine specified for execution immediately after
execution of the user program ends.
•
If the user routine is to use a general-purpose register, saving the contents of the register,
making the initial setting, and restoring the contents should all be done within the routine.
• The specified routine is also executed when the following operations are performed:
⎯ Step operations
⎯ Watching or changing memory during user program execution. ∗
Note: When parallel access is enabled and memory access is disabled, the user routine is not
executed.
• The device groups listed below do not support this function.
⎯ -H8S/2118 device group
⎯ -H8S/2378 device group
⎯ -H8S/2339 device group
⎯ -H8S/2215R device group
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 117 of 190
H8S, H8SX Family E10A-USB Emulator
5.6
Section 5 Debugging
Operation with Multiple Debugging Platforms
The High-performance Embedded Workshop is capable of operation with multiple debugging
platforms.
When selecting [Renesas High-performance Embedded Workshop] -> [High-performance
Embedded Workshop] from [Programs] in the [Start] menu to initiate another High-performance
Embedded Workshop, two emulators can be used separately for debugging.
5.6.1
Distinguishing Two Emulators
Connect two emulators to the USB connector. Then, initiate the High-performance Embedded
Workshop using the tutorial workspace. The following message is displayed.
Figure 5.16 Message for Driver Selection
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 118 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Click the [OK] button. The following dialog box will appear.
Figure 5.17 [Driver Details] Dialog Box (1)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 119 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
Select [Renesas E-Series USB Driver] from the [Driver] drop-down list box and open the
[Channel] drop-down list box. Channel information for two emulators is displayed in the
[Channel] drop-down list box as shown in figure 5.18.
Figure 5.18 [Driver Details] Dialog Box (2)
Information displayed in figure 5.18 is the information of the USB connector to which the
emulators are connected.
Note: The displayed character strings of the information differ according to the host computer’s
environment.
Check which of the character strings of information show emulators.
Select [<no driver selected>] in the [Driver] drop-down list box and disconnect one emulator from
the USB connector. After that, select [Renesas E-Series USB Driver] in the [Driver] drop-down
list box. Only information on the USB connector that the emulator is connected to is displayed in
the [Channel] drop-down list box.
The above procedures are used to discern which of the emulators are indicated by the displayed
character strings of information in the [Channel] drop-down list box.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 120 of 190
H8S, H8SX Family E10A-USB Emulator
Section 5 Debugging
When initiating the master High-performance Embedded Workshop, in the [Channel] drop-down
list box, select the information on the USB connector of the emulator that is connected to the
master CPU. Initiate the High-performance Embedded Workshop using the normal procedures.
When initiating the slave High-performance Embedded Workshop, in the [Channel] drop-down
list box, select the information on the USB connector of the emulator that is connected to the slave
CPU.
Display example:
• E10A-USB: [Cont0] – [Port1]
The emulator is connected to port 1 of USB controller 0.
• E10A-USB: [Cont4] – [Port7] [Port3]
The emulator is connected to general hub port 3 which has been connected to port
7 of USB controller 4 (this is displayed when the USB hub is connected).
Note: Connecting Two or More Emulators
If two or more emulators are to be connected to a single personal computer, the emulator
that was connected earlier should be in the break state whenever you connect another
emulator.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 121 of 190
H8S, H8SX Family E10A-USB Emulator
5.7
5.7.1
Section 5 Debugging
Saving of Hardware-Break Settings
Saving and Loading Hardware-Break Settings
This facility allows you to save or load hardware-break settings, i.e. the "Break condition" settings
for all channels shown on the [Breakcondition] sheet of the [Eventpoints] window (note that the
breakpoints that have been set will not be saved). The hardware-break settings are saved in a file
with the ".bcs" extension and, after that, you can load these settings. This makes it easier to switch
the hardware-break settings for use in debugging.
5.7.2
How to Save Hardware-Break Settings
Use the [Save Break condition] dialog box to save hardware-break settings. To open the [Save
Break condition] dialog box, select [Setup -> Emulator -> Save Break condition] or click on the
[Save Break condition] toolbar button ( ).
Figure 5.19 [Save Break condition] Dialog Box
Select a file name from the [File name] combo box. If you wish to create a new file, click on the
[
] button and enter the name of the file. Clicking on the [Save] button saves the settings.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 122 of 190
H8S, H8SX Family E10A-USB Emulator
5.7.3
Section 5 Debugging
How to Load Hardware-Break Settings
Use the [Load Break condition] dialog box to load hardware-break settings. To open the [Load
Break condition] dialog box, select [Setup -> Emulator -> Load Break condition] or click on the
[Load Break condition] toolbar button (
).
Figure 5.20 [Load Break condition] Dialog Box
Select a file name from the [File name] combo box. If you wish to specify a file that is not
included in the list, click on the [
] button and enter the name of the file. Clicking on the
[Load] button loads the settings.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 123 of 190
H8S, H8SX Family E10A-USB Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Section 5 Debugging
Page 124 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Section 6 Tutorial
6.1
Introduction
This section describes the main functions of the emulator by using a tutorial program. The
explanation of the tutorial program will be given in this section using the H8S device. When the
H8SX device is used, the displays of some dialog boxes will differ. However, the operation similar
to that of the H8S device can be performed.
The tutorial program is based on the C++ program that sorts ten random data items in ascending or
descending order. The tutorial program performs the following actions:
• The main function generates random data to be sorted.
• The sort function sorts the generated random data in ascending order.
• The change function then sorts the data in descending order.
The file tutorial.cpp contains source code for the tutorial program of the H8S, H8SX family
devices. The file Tutorial.abs is a compiled load module in the Elf/Dwarf2 format.
Note: After recompilation, the addresses may differ from those given in this section.
6.2
Running the High-performance Embedded Workshop
To run the High-performance Embedded Workshop, refer to section 3.11, System Check.
6.3
Setting up the Emulator
This section describes the basic settings of the emulator.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 125 of 190
H8S, H8SX Family E10A-USB Emulator
6.4
Section 6 Tutorial
Setting the [Configuration] Dialog Box
Select [Emulator] then [Systems…] from the [Setup] menu for the basic settings of the emulator.
The [Configuration] dialog box is displayed.
Figure 6.1 [Configuration] Dialog Box
Note: The items that can be set in this dialog box differ depending on the product. For details on
the settings for each product, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 126 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Set options as follows:
Table 6.1 [General] Page Options
Option
Value (Default)
Device
H8S/xxxx
Emulation mode
Normal (normal execution)
Step option
Disables interrupts during single step execution
JTAG clock
Sets the frequency* of the JTAG clock.
Flash memory synchronization when
the user program is stopped
Disable
Step Over option
Executes the step over and step out by using the breakpoint.
Flash memory write after download
Disable
Short break
Enable
Note: The range of frequency for the JTAG clock differs depending on the supported MCU.
Click the [OK] button to set a configuration.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 127 of 190
H8S, H8SX Family E10A-USB Emulator
6.5
Section 6 Tutorial
Checking the Operation of RAM
Check that RAM is operating correctly.
Display and edit the contents of the memory in the [Memory] window to check that the memory is
operating correctly.
Note: The memory can be installed on the board in some MCUs. In this case, however, the
above way of checking the operation of memory may be inadequate. It is recommended
that a program for checking the memory be created.
• Select [Memory…] from the [CPU] submenu of the [View] menu and enter the RAM address
in the [Display Address] edit box. Here, enter H’FFC000. Then enter H’000000 and
H’FFFFFF in the [Scroll Start Address] and [Scroll End Address] edit boxes, respectively.
Figure 6.2 [Display Address] Dialog Box
Note: The settings of the RAM area differ depending on the product. For details, refer to the
hardware manual.
• Click the [OK] button. The [Memory] window is displayed and shows the specified memory
area.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 128 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Figure 6.3 [Memory] Window
• Placing the mouse cursor on a point in the display of data in the [Memory] window and doubleclicking allows the values at that point to be changed. Data can also be directly edited around
the current position of the text cursor.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 129 of 190
H8S, H8SX Family E10A-USB Emulator
6.6
6.6.1
Section 6 Tutorial
Downloading the Tutorial Program
Downloading the Tutorial Program
Download the object program to be debugged.
In this emulator, it is enabled to download the program and set the PC breakpoint in the internal
ROM area. For the method to set the PC breakpoint, refer to section 6.16.1, PC Break Function.
• Select [Download module] by right-clicking on “Tutorial.abs” under “Download modules”.
Figure 6.4 Downloading the Tutorial Program
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 130 of 190
H8S, H8SX Family E10A-USB Emulator
6.6.2
Section 6 Tutorial
Displaying the Source Program
The High-performance Embedded Workshop allows the user to debug a user program at the source
level.
• Double-click [tutorial.cpp] under [C++ source file].
Figure 6.5 [Editor] Window (Displaying the Source Program)
• Select the [Display] option from the [Setup] menu to set a font and size that are legible, if
necessary.
Initially the [Editor] window shows the start of the user program, but the user can use the scroll bar
to scroll through the user program and look at the other statements.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 131 of 190
H8S, H8SX Family E10A-USB Emulator
6.7
Section 6 Tutorial
Setting a PC Breakpoint
A PC breakpoint is a simple debugging function.
The [Editor] window provides a very simple way of setting a PC breakpoint at any point in a
program. For example, to set a PC breakpoint at the sort function call:
•
Select by double-clicking the [S/W breakpoint] column on the line containing the sort
function call.
Figure 6.6 [Editor] Window (Setting a PC Breakpoint)
The symbol • will appear on the line containing the sort function. This shows that a PC
breakpoint has been set.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 132 of 190
H8S, H8SX Family E10A-USB Emulator
6.8
Section 6 Tutorial
Setting Registers
Set values of the program counter and the stack pointer before executing the program.
• Select [Registers] from the [CPU] submenu of the [View] menu. The [Register] window is
displayed.
Figure 6.7 [Register] Window
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 133 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
• To change the value of the program counter (PC), double-click the value area in the [Register]
window with the mouse. The following dialog box is then displayed, and the value can be
changed. Set the program counter to H’400 in this tutorial program, and click the [OK] button.
Figure 6.8 [Register] Dialog Box (PC)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 134 of 190
H8S, H8SX Family E10A-USB Emulator
6.9
Section 6 Tutorial
Executing the Program
Execute the program as described in the following:
• To execute the program, select [Go] from the [Debug] menu, or click the [Go] button on the
toolbar.
Figure 6.9 [Go] Button
When the program execution is started, ‘**RUNNING’ is displayed on the status bar.
The program will be executed up to the breakpoint that has been set, and an arrow will be
displayed in the [S/W breakpoint] column to show the position that the program has halted, with
the message [BREAKPOINT] in the status bar.
Note: When the source file is displayed after a break, a path of the source file may be inquired.
The location of the source file is as follows:
<Drive where the OS has been installed>:
\WorkSpace\Tutorial\E10A-USB\H8S\xxxx\Tutorial
Here, ‘xxxx’ means the target product group.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 135 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Figure 6.10 [Editor] Window (Break State)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 136 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The user can see the cause of the break that occurred last time in the [Status] window.
• Select [Status] from the [CPU] submenu of the [View] menu. After the [Status] window is
displayed, open the [Platform] sheet, and check the Status of Cause of last break.
Figure 6.11 [Status] Window
Note: The items that can be displayed in this window differ depending on the product. For the
items that can be displayed, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 137 of 190
H8S, H8SX Family E10A-USB Emulator
6.10
Section 6 Tutorial
Reviewing Breakpoints
The user can see all the breakpoints set in the program in the [Event] window.
• Select [Eventpoints] from the [Code] submenu of the [View] menu. The [Event] window is
displayed. Select the [Breakpoint] sheet.
Figure 6.12 [Event] Window
The popup menu, opened by clicking the [Event] window with the right-hand mouse button,
allows the user to set or change breakpoints, add new breakpoints, and delete, enable, or disable
breakpoints.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 138 of 190
H8S, H8SX Family E10A-USB Emulator
6.11
Section 6 Tutorial
Viewing Memory
When the label name is specified, the user can view the memory contents that the label has been
registered in the [Memory] window. For example, to view the memory contents corresponding to
_main in word size:
• Select [Memory…] from the [CPU] submenu of the [View] menu and enter the RAM address
in the [Display Address] edit box. Here, enter H’FFC000. Then enter H’000000 and
H’FFFFFF in the [Scroll Start Address] and [Scroll End Address] edit boxes, respectively.
Figure 6.13 [Display Address] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 139 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
• Click the [OK] button. The [Memory] window showing the specified area of memory is
displayed.
Figure 6.14 [Memory] Window
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 140 of 190
H8S, H8SX Family E10A-USB Emulator
6.12
Section 6 Tutorial
Watching Variables
As the user steps through a program, it is possible to watch that the values of variables used in the
user program are changed. For example, set a watch on the long-type array a declared at the
beginning of the program, by using the following procedure:
• Click the left of displayed array a in the [Editor] window to position the cursor.
• Select [Instant Watch...] with the right-hand mouse button.
The following dialog box will be displayed.
Figure 6.15 [Instant Watch] Dialog Box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 141 of 190
H8S, H8SX Family E10A-USB Emulator
•
Section 6 Tutorial
Click the [Add] button to add a variable to the [Watch] window.
Figure 6.16 [Watch] Window (Displaying the Array)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 142 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The user can also add a variable to the [Watch] window by specifying its name.
• Click the [Watch] window with the right-hand mouse button and select [Add Watch…] from
the popup menu.
The following dialog box will be displayed. Enter variable i.
Figure 6.17 [Add Watch] Dialog Box
• Click the [OK] button.
The [Watch] window will now also show the int-type variable i.
Figure 6.18 [Watch] Window (Displaying the Variable)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 143 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The user can click mark ‘+’ at the left side of array a in the [Watch] window to watch all the
elements.
Figure 6.19 [Watch] Window (Displaying Array Elements)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 144 of 190
H8S, H8SX Family E10A-USB Emulator
6.13
Section 6 Tutorial
Stepping Through a Program
The High-performance Embedded Workshop provides a range of step menu commands that allow
efficient program debugging.
Table 6.2 Step Option
Menu
Command
Description
Step In
Executes each statement, including statements within functions.
Step Over
Executes a function call in a single step.
Step Out
Steps out of a function, and stops at the statement following the statement in the
program that called the function.
Step…
Steps the specified times repeatedly at a specified rate.
6.13.1
Executing [Step In] Command
The [Step In] command steps into the called function and stops at the first statement of the called
function.
• To step through the sort function, select [Step In] from the [Debug] menu, or click the [Step
In] button on the toolbar.
Figure 6.20 [Step In] Button
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 145 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Figure 6.21 [Editor] Window (Step In)
• The highlighted line moves to the first statement of the sort function in the [Editor] window.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 146 of 190
H8S, H8SX Family E10A-USB Emulator
6.13.2
Section 6 Tutorial
Executing [Step Out] Command
The [Step Out] command steps out of the called function and stops at the next statement of the
calling statement in the main function.
• To step out of the sort function, select [Step Out] from the [Debug] menu, or click the [Step
Out] button on the toolbar.
Note: It takes time to execute this function. When the calling source is clarified, use [Go To
Cursor].
Figure 6.22 [Step Out] Button
Figure 6.23 [High-performance Embedded Workshop] Window (Step Out)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 147 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The data of variable a displayed in the [Watch] window is sorted in ascending order.
6.13.3
Executing [Step Over] Command
The [Step Over] command executes a function call as a single step and stops at the next statement
of the main program.
• To step through all statements in the change function at a single step, select [Step Over] from
the [Debug] menu, or click the [Step Over] button on the toolbar.
Figure 6.24 [Step Over] Button
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 148 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Figure 6.25 [High-performance Embedded Workshop] Window (Step Over)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 149 of 190
H8S, H8SX Family E10A-USB Emulator
6.14
Section 6 Tutorial
Forced Breaking of Program Executions
The High-performance Embedded Workshop can force a break in the execution of a program.
• Cancel all breakpoints settings.
• To execute the remaining sections of the main function, select [Go] from the [Debug] menu or
the [Go] button on the toolbar.
Figure 6.26 [Go] Button
• The program goes into an endless loop. To force a break in execution, select [Halt] from the
[Debug] menu or the [Stop] button on the toolbar.
Figure 6.27 [Stop] Button
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 150 of 190
H8S, H8SX Family E10A-USB Emulator
6.15
Section 6 Tutorial
Displaying Local Variables
The user can display local variables in a function using the [Locals] window. For example, we will
examine the local variables in the main function, which declares four local variables: a, j, i, and
p_sam.
• Select [Locals] from the [Symbol] submenu of the [View] menu. The [Locals] window is
displayed.
The [Locals] window shows the local variables in the function currently pointed to by the program
counter, along with their values. Note, however, that the [Locals] window is initially empty
because local variables are yet to be declared.
Figure 6.28 [Locals] Window
• Click mark ‘+’ at the left side of array a in the [Locals] window to display the elements.
• When the user refers to the elements of array a before and after the execution of the sort
function, it is clarified that random data is sorted in descending order.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 151 of 190
H8S, H8SX Family E10A-USB Emulator
6.16
Section 6 Tutorial
Break Function
The emulator has PC and hardware break functions. With the High-performance Embedded
Workshop, a PC breakpoint can be set using the [Breakpoint] sheet of the [Event] window, and a
hardware break condition can be set using the [Breakcondition] sheet.
An overview and setting of the break function are described below.
6.16.1
PC Break Function
The emulator can set up to 255 PC breakpoints. Other methods for setting a PC breakpoint than in
section 6.7, Setting a PC Breakpoint, are described below.
• Select [Eventpoints] from the [Code] submenu of the [View] menu. The [Event] window is
displayed.
• Select the [Breakpoint] sheet.
Figure 6.29 [Event] Window (Before Setting a PC Breakpoint)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 152 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
• Double-click the [S/W breakpoint] column on the [Editor] window. A PC breakpoint is set.
Figure 6.30 [Editor] Window (Setting a PC Breakpoint)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 153 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
• When the PC breakpoint is set in the [Event] window, click the [Event] window with the righthand mouse button and select [Add…] from the popup menu.
Figure 6.31 [Set Break] Dialog Box
• Click the [OK] button.
Note: The address values described in this section will differ depending on the tutorial for each
product.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 154 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The PC breakpoint that has been set is displayed in the [Event] window.
Figure 6.32 [Event] Window (PC Breakpoint Setting)
Note: The items that can be displayed in this window differ according to the product. For the
items that can be displayed, refer to the online help.
To stop the tutorial program at the PC breakpoint, the following procedure must be executed:
• Close the [Event] window.
• Set the program counter value (PC = H’400) that was set in section 6.8, Setting Registers, in
the [Register] window. Click the [Go] button.
• If program execution is failed, reset the device and execute again the procedures above.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 155 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The program runs, and stops at the set PC breakpoint.
Figure 6.33 [Editor] Window at Execution Stop (PC Break)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 156 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The [Status] window displays the following contents.
Figure 6.34 Displayed Contents of the [Status] Window (PC Break)
Note: The items that can be displayed in this window differ depending on the product. For the
items that can be displayed, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 157 of 190
H8S, H8SX Family E10A-USB Emulator
6.17
Section 6 Tutorial
Hardware Break Function
A method is given below in which the address bus condition is set under Break Condition 1 as
hardware break conditions.
• Select [Eventpoints] from the [Code] submenu of the [View] menu. The [Event] window is
displayed.
• The PC breakpoint that has been previously set is deleted. Click the [Event] window with the
right-hand mouse button and select [Delete All] from the popup menu to cancel all PC
breakpoints that have been set.
• Double-click the [Event] column in the [Editor] window. The specified address shows
Break Condition is set.
and a
• Click the [Break condition] tab.
• Select a line of Break condition 1 in the [Event] window. When highlighted, double-click this
line.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 158 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Figure 6.35 [High-performance Embedded Workshop] Window ([Break condition 1])
• The [Break condition 1] dialog box is displayed.
• The data condition can be set besides the address condition.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 159 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
Figure 6.36 [condition] Page ([Break condition 1] Dialog Box)
• Click the [OK] button.
• The content that has been set is reflected in the [Event] window.
• The first point display in the State line changes from Disable to Enable.
• The first point display in the Condition line changes from None to Address = H’00008FC
(Tutorial.cpp/47) pcafter.
• Set the program counter value (PC = H’400) that was set in section 6.8, Setting Registers, in
the [Register] window. Click the [Go] button.
Note: The items that can be set in this page differ depending on the product. For details on the
settings for each product, refer to the online help.
The address values described in this section will differ depending on the tutorial for each
product.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 160 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The program runs and then stops at the condition specified under Break Condition 1.
Figure 6.37 [Editor] Window at Execution Stop (Break Condition 1)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 161 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
The [Status] window displays the following contents.
Figure 6.38 Displayed Contents of the [Status] Window (Break Condition 1)
Note: The items that can be displayed in this window differ depending on the product. For the
items that can be displayed, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 162 of 190
H8S, H8SX Family E10A-USB Emulator
6.18
Section 6 Tutorial
Trace Functions
The emulator has a branch-instruction trace function.
In H8S family, the four-channel branch source addresses, mnemonics, operands, source lines, and
labels are displayed.
In H8SX family, the eight-channel branch source or destination addresses, mnemonics, operands,
source lines, and labels are displayed.
6.18.1
Displaying the Trace Window
Select [Trace] from the [Code] submenu of the [View] menu.
Run the program as shown in the example of section 6.16.1, PC Break Function. The trace results
are displayed in the [Trace] window after the program execution is completed.
Figure 6.39 [Trace] Window
If necessary, adjust the column widths by dragging borders in the header bar (immediately below
the title bar).
Note: The number of branch instructions that can be acquired by a trace and the trace display
differ depending on the product. For details on the specifications of each product, refer to
the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 163 of 190
H8S, H8SX Family E10A-USB Emulator
6.19
Section 6 Tutorial
Stack Trace Function
The emulator uses the information on the stack to display the names of functions in the sequence of
calls that led to the function to which the program counter is currently pointing.
Note: This function can be used only when the load module that has the Elf/Dwarf2-type
debugging information is loaded. Such load modules are supported in H8C/C++ compiler
V3.0 or later.
• Double-click the [S/W breakpoint] column in the sort function and set a PC breakpoint.
Figure 6.40 [Editor] Window (PC Breakpoint Setting)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 164 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
• Set the same program counter value (PC = H’400) as was set in section 6.8, Setting Registers
(again, use the [Register] window). Click the [Go] button.
• After the break in program execution, select [Stack Trace] from the [Code] submenu of the
[View] menu to open the [Stack Trace] window.
Figure 6.41 [Stack Trace] Window
Figure 6.41 shows that the position of the program counter is currently at the selected line of the
sort() function, and that the sort() function is called from the tutorial() function.
6.20
What Next?
This tutorial has described the major features of the emulator and the use of the High-performance
Embedded Workshop.
Sophisticated debugging can be carried out by using the emulation functions that the emulator
offers. This provides for effective investigation of hardware and software problems by accurately
isolating and identifying the conditions under which such problems arise.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 165 of 190
H8S, H8SX Family E10A-USB Emulator
Section 6 Tutorial
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 166 of 190
H8S, H8SX Family E10A-USB Emulator
Section 7 Maintenance and Guarantee
Section 7 Maintenance and Guarantee
This section describes maintenance, guarantee, repair provisions, and how to request for repair of
the emulator.
7.1
User Registration
When you purchase our product, be sure to register as a user. For user registration, refer to the
section of ‘User Registration’ (p. iii) of this user's manual.
7.2
Maintenance
1. If dust or dirt collects on any equipment of this product, wipe the board dry with a soft cloth.
Do not use thinner or other solvents because these chemicals can cause the equipment's surface
coating to separate.
2. When you do not use this product for a long period, for safety purposes, disconnect the power
cable from the power supply.
7.3
Guarantee
If your product becomes faulty within one year after its purchase while being used under good
conditions by observing ‘IMPORTANT INFORMATION’ described in this user's manual, we will
repair or replace your faulty product free of charge. Note, however, that if your product's fault is
raised by any one of the following causes, we will repair it or replace it with new one with extracharge:
• Misuse, abuse, or use under extraordinary conditions
• Unauthorized repair, remodeling, maintenance, and so on
• Inadequate user's system or misuse of it
• Fires, earthquakes, and other unexpected disasters
In the above cases, contact your local distributor. If your product is being leased, consult the
leasing company or the owner.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 167 of 190
H8S, H8SX Family E10A-USB Emulator
7.4
7.4.1
Section 7 Maintenance and Guarantee
Repair Provisions
Repair with Extra-Charge
The products elapsed more than one year after purchase can be repaired with extra-charge.
7.4.2
Replacement with Extra-Charge
If your product's fault falls in any of the following categories, the fault will be corrected by
replacing the entire product instead of repair, or you will be advised to purchase new one,
depending on the severity of the fault.
• Faulty or broken mechanical parts
• Flaw, separation, or rust in coated or plated parts
• Flaw or cracks in plastic parts
• Faults or breakage caused by improper use or unauthorized repair or modification
• Heavily damaged electric circuits due to overvoltage, overcurrent or shorting of power supply
• Cracks in the printed circuit board or burnt-down patterns
• Wide range of faults that makes replacement less expensive than repair
• Unlocatable or unidentified faults
7.4.3
Expiration of the Repair Period
When a period of one year elapses after the model was dropped from production, repairing
products of the model may become impossible.
7.4.4
Transportation Fees at Sending Your Product for Repair
Send your product to us for repair at your expense.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 168 of 190
H8S, H8SX Family E10A-USB Emulator
7.5
Section 7 Maintenance and Guarantee
How to Make a Request for Repair
If your product is found faulty, follow the procedure below to send your product for repair.
Fill in the Repair Request Sheet included with this product, then send it along with this product for
repair to your local distributor. Make sure that information in the Repair Request Sheet is written
in as much detail as possible to facilitate repair.
CAUTION
Note on Transporting the Product:
When sending your product for repair, use the packing
box and cushion material supplied with this product when
delivered to you and specify handling caution for it to be
handled as precision equipment. If packing of your product is
not complete, it may be damaged during transportation. When
you pack your product in a bag, make sure to use conductive
polyvinyl supplied with this product (usually a blue bag).
When you use other bags, they may cause a trouble on your
product because of static electricity.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 169 of 190
H8S, H8SX Family E10A-USB Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Section 7 Maintenance and Guarantee
Page 170 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix A Troubleshooting
Appendix A Troubleshooting
1. I have a text file open in the editor but syntactic color-coding is not being displayed.
Ensure that you have named the file (i.e. saved it) and that the “Syntax coloring” check box is set
on the “Editor” tab of the “Options” dialog box, which is launched via [Setup -> Options...].
The High-performance Embedded Workshop looks up the filename extension to determine the
group to which the file belongs and decides whether or not coloring should be applied to the file.
To view the currently defined filename extensions and file groups, select [Project -> File
Extensions...] to launch the “File Extensions” dialog box. To view the coloring information,
select [Setup -> Format] to display the “Color” tab of the “Format” dialog box.
2. I want to change the settings of a tool but the [Tools->Administration…] menu option is not
selectable.
[Tools->Administration...] is not selectable while a workspace is open. To open the “Tool
Administration” dialog box, close the current workspace.
3. I opened a workspace from my PC, and one of my colleagues opened the same workspace
simultaneously from another PC. I changed the settings of the workspace and saved it. My
colleague saved the workspace after me. I opened the workspace again and found that the
settings of the workspace differed from those I had made.
The last settings to be saved are effective. While a workspace is open in the High-performance
Embedded Workshop, updating of the workspace is within the memory. The settings are not
saved in a file unless the user intentionally saves the workspace.
In addition to above, refer to FAQs on the emulator and High-performance Embedded Workshop
on the Renesas web site (www.renesas.com).
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 171 of 190
H8S, H8SX Family E10A-USB Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Appendix A Troubleshooting
Page 172 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix B Window Functions
Appendix B Window Functions
This section describes the window functions that can be used with the E10A-USB emulator Highperformance Embedded Workshop. Here, the High-performance Embedded Workshop common
functions are omitted, and only the emulation functions are described.
Table B.1 Window Functions
Toolbar
Button
Menu
Option
Shortcut
View
Disassembly
Ctrl + D
Opens the [Disassembly]
window.
Command Line
Ctrl + L
Opens the [Command Line]
window.
TCL toolkit
Shift +
Ctrl + L
Opens the [Console] window.
Workspace
Alt + K
Opens the [Workspace]
window.
Output
Alt + U
Opens the [Output] window.
Difference
CPU
Symbol
Remarks
Opens the [Difference]
window.
Registers
Ctrl + R
Opens the [Register] window.
Memory…
Ctrl + M
Opens the [Memory] window.
IO
Ctrl + I
Opens the [IO] window.
Status
Ctrl + U
Opens the [Status] window.
Labels
Shift +
Ctrl + A
Opens the [Labels] window.
Watch
Ctrl + W
Opens the [Watch] window.
Locals
Shift +
Ctrl + W
Opens the [Locals] window.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 173 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix B Window Functions
Table B.1 Window Functions (cont)
Menu
Option
View
(cont)
Code
Graphic
Setup
Radix
Emulator
Shortcut
Toolbar
Button
Remarks
Eventpoints
Ctrl + E
Opens the [Event] window.
Trace
Ctrl + T
Opens the [Trace] window.
Stack Trace
Ctrl + K
Opens the [Stack Trace]
window.
Image…
Shift + Ctrl
+G
Opens the [Image] window.
Waveform…
Shift + Ctrl
+V
Opens the [Waveform] window.
Hexadecimal
Uses a hexadecimal for
displaying a radix in which the
numerical values will be
displayed and entered by
default.
Decimal
Uses a decimal for displaying a
radix in which the numerical
values will be displayed and
entered by default.
Octal
Uses an octal for displaying a
radix in which the numerical
values will be displayed and
entered by default.
Binary
Uses a binary for displaying a
radix in which the numerical
values will be displayed and
entered by default.
System…
Opens the [Configuration] dialog
box allowing the user to modify
the debugging platform settings.
Start/Stop Function
Settings…
Displays the [Start/Stop function
settings] dialog box.
Save Break
condition …
Opens the [Save Break
condition] dialog box
Load Break
condition …
Opens the [Load Break
condition] dialog box
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 174 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix B Window Functions
Table B.1 Window Functions (cont)
Shortcut
Toolbar
Button
Menu
Option
Remarks
Debug
Debug Sessions…
Opens the [Debug Sessions]
dialog box to list, add, or remove
the debug session.
Debug Settings…
Opens the [Debug Settings] dialog
box to set the debugging
conditions or download modules.
Reset CPU
Resets the target MCU and sets
the PC to the reset vector address.
Go
F5
Starts executing the user program
at the current PC.
Reset Go
Shift + F5
Resets the target MCU and
executes the user program from
the reset vector address.
Go To Cursor
Starts executing the user
program at the current PC until
the PC reaches the address
indicated by the current text
cursor position.
Set PC To Cursor
Sets the PC to the address at the
row of the text cursor.
Display PC
Shift + Ctrl +
Y
Run…
Displays the current PC value.
Launches the [Run Program]
dialog box allowing the user to
enter the PC or PC breakpoint
during executing the user
program.
Step In
F11
Executes a block of user program
before breaking.
Step Over
F10
Executes a block of user program
before breaking. If a subroutine
call is reached, then the
subroutine will not be entered.
Step Out
Shift + F11
Executes the user program to
reach the end of the current
function.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 175 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix B Window Functions
Table B.1 Window Functions (cont)
Menu
Option
Debug
Step…
Step
Mode
Shortcut
Toolbar
Button
Remarks
Launches the [Step Program]
dialog box allowing the user to
modify the settings for stepping.
Auto
Steps only one source line when
the [Editor] window is active.
When the [Disassembly] window
is active, stepping is executed in
a unit of assembly instructions.
Assembly
Executes stepping in a unit of
assembly instructions.
Source
Steps only one source line.
Halt Program
Esc
Stops the execution of the user
program.
Connect
Connects the debugging
platform.
Initialize
Disconnects the debugging
platform and connects it again.
Disconnect
Disconnects the debugging
platform. This option cannot be
used in some products.
Download Modules
Downloads the object program.
Unload Modules
Unloads the object program.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 176 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix C Command-Line Functions
Appendix C Command-Line Functions
The emulator supports the commands that can be used in the command-line window.
For details, refer to the online help.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 177 of 190
H8S, H8SX Family E10A-USB Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Appendix C Command-Line Functions
Page 178 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix D Notes on High-performance Embedded Workshop
Appendix D Notes on High-performance Embedded
Workshop
1. Note on Moving Source File Position after Creating Load Module
When the source file is moved after creating the load module, the [Open] dialog box may be
displayed to specify the source file during the debugging of the created load module. Select the
corresponding source file and click the [Open] button.
2. Source-Level Execution
⎯ Source file
Do not display source files that do not correspond to the load module in the program
window. For a file having the same name as the source file that corresponds to the load
module, only its addresses are displayed in the program window. The file cannot be
operated in the program window.
⎯ Step
Even standard C libraries are executed. To return to a higher-level function, enter Step Out.
In a for statement or a while statement, executing a single step does not move execution to
the next line. To move to the next line, execute two steps.
3. Operation during Accessing Files
Do not perform other operations during downloading the load module or saving in the [Verify
Memory], [Save Memory], or [Trace] window because this will not allow correct file accessing
to be performed.
4. Watch
⎯ Local variables at optimization
Depending on the generated object code, local variables in a C source file that is compiled
with the optimization option enabled will not be displayed correctly. Check the generated
object code by displaying the [Disassembly] window.
If the allocation area of the specified local variable does not exist, displays as follows.
Example:
The variable name is asc.
asc = ? - target error 2010 (xxxx)
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 179 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix D Notes on High-performance Embedded Workshop
⎯ Variable name specification
When a name other than a variable name, such as a symbol name or function name, is
specified, no data is displayed.
Example:
The function name is main.
main =
5. Line Assembly
⎯ Input radix
Regardless of the radix setting, the default for line assembly input is decimal. Specify H’ or
0x for hexadecimal input on H8-series MCUs.
6. Command Line Interface
⎯ Batch file
To display the message “Not currently available” while executing a batch file, enter the
sleep command. Adjust the sleep time length which differs according to the operating
environment.
Example: To display “Not currently available” during memory_fill execution:
sleep d’3000
memory_fill 0 ffff 0
⎯ File specification by commands
The current directory may be altered by file specifications in commands. It is
recommended to use absolute paths to specify the files in a command file so that the current
directory alteration is not affected.
Example:
FILE_LOAD C\HEW\Tools\Renesas\DebugComp\Platform
\E10A-USB\Tutorial\Debug_H8S_xxxx_E10A-USB_SYSTEM
\Tutorial.abs
7. Memory Save during User Program Execution
Do not execute saving, verifying, comparing, or searching of memory during user program
execution.
8. Load of Motorola S-type Files
This High-performance Embedded Workshop does not support Motorola S-type files with only
the CR code (H'0D) at the end of each record. Load Motorola S-type files with the CR and LF
codes (H'0D0A) at the end of each record.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 180 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix D Notes on High-performance Embedded Workshop
9. [I/O] Window
⎯ Display and modification
Do not change values in the [I/O Registers] window because the emulator uses the address
break controller.
Note that the emulator does not support the display of the invalid module or bit information
in the [I/O] window.
10. Note on [Register] Window Operation during Program Execution
The register value cannot be changed in the [Register] window during program execution. Even
if the changed value is displayed, the register contents are not changed actually.
11. Break Functions
When the PC breakpoint is set in the flash memory area, the program is written to the flash
memory each time the user program is executed. At this time, note that the number of
rewritable times will be decreased.
⎯ BREAKPOINT cancellation
When the contents of the BREAKPOINT address are modified during user program
execution, the following message is displayed when the user program stops.
Checking of data at the address of the breakpoint where the user program execution
stopped has failed. This is because the data at the address has been changed, or writing or
reading was not successful. So the original data has not been written back to the address.
Address = H′xxxx
12. Number of BREAKPOINT and [Stop At] Settings in the [Run...] Menu
The maximum number of BREAKPOINTs and [Stop At] settings allowed in the [Run...] menu
is 255. Therefore, when 255 BREAKPOINTs are set, specification by [Stop At] in the [Run...]
menu becomes invalid. Use the BREAKPOINTs and [Stop At] in the [Run...] menu with 255
or less total settings.
13. Note on RUN-TIME Display
The execution time of the user program displayed in the [Status] window is not a correct value
since the timer in the host computer has been used.
14. Note on Displaying Timeout error
If Timeout error is displayed, the emulator cannot communicate with the target MCU.
Turn off the emulator and the user system and connect the emulator again by using the Highperformance Embedded Workshop.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 181 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix D Notes on High-performance Embedded Workshop
15. Support of Double Float Format
In the following memory operations, the double float format is not supported:
⎯ [Fill Memory] dialog box
⎯ [Search Memory] dialog box
⎯ MEMORY_FILL command
The [Length] specification in the [Move] dialog box is ignored. Memory is copied in a byte
unit.
16. Note on Using the [Run Program] Dialog Box
When [Run...] is selected from the [Debug] menu to specify the stop address, there is the
following note:
When the breakpoint that has been set as Disable is specified as the stop address, note that the
breakpoint becomes Enable when the user program stops.
17. Memory Access during User Program Execution
When a memory is accessed from the memory window, etc. during user program execution, the
user program is resumed after it has stopped in the emulator to access the memory. Therefore,
realtime emulation cannot be performed.
When [Short break] or [Memory access] (default: ‘Enable’) is set to ‘Disable’ in the
[Configuration] dialog box, temporary halting of the user program execution by a memory
access is disabled. However, even if you attempt to view memory data during the user program
execution via window [IO] or [Memory], automatic update of the watch function, or the use of
the tool-chip watch function, all values are shown as H’FF.
The stopping time of the user program is as follows:
Environment:
TM
Host computer: Core 2 Duo 2 GHz
H8S/2377F: 33 MHz (system clock frequency)
When a one-byte memory is read from the command-line window, the stopping time will be
about 65 ms (the same result will apply to H8SX).
18. Setting Hardware Breakpoints While the User Program is Running
When you set a hardware breakpoint while the user program is running, the emulator suspends
and then resumes the program execution. The program is thus not running in realtime.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 182 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix D Notes on High-performance Embedded Workshop
19. MCU for use in debugging
The emulator is also applicable as a programming tool in mass production when it is operating
in the [Program Flash] mode.
However, the flash memory of an actual MCU which has been used in connection with the
emulator in the [E10A-USB Emulator] mode for debugging will have been programmed and
subjected to stress accordingly. Do not use an MCU that has been used for debugging in a
mass-produced product.
20. Suspending PC Operation while Using the Emulator
Do not place the host computer in sleep mode or suspended mode while using the emulator.
The emulator is not usable when the host computer is in these modes. Reconnect the emulator
after the host computer has returned from sleep mode or suspended mode.
21. Verification of Memory
Use the FILE_VERIFY command to verify memory. Do not use [Verify Memory…] in the
[File] menu.
22. Overwrite of a File
In command line interface, a file that has the same name as the output file is overwritten
without asking the user.
23. Usage with Other Products
To install the SuperH™ RISC engine C/C++ compiler package or H8SX, H8S, or H8 Family
C/C++ compiler package after installing the emulator software for High-performance
Embedded Workshop, select [High-performance Embedded Workshop] as the component to be
installed in [Select Components] during installation of the compiler package.
24. Download of Load Modules
When load modules are downloaded, select [Debug] -> [Download] -> [All Download
modules].
25. Program Flash Mode
When MCUs are continuously programmed, be sure to turn the target on or off.
26. Memory Access in the Program Flash Mode
Memory cannot be accessed in the Program Flash mode. In this mode, values displayed in the
[Memory] or [IO] window are dummy.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 183 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix D Notes on High-performance Embedded Workshop
27. Memory Access during Flash Memory Programming
During flash memory programming (e.g., user program execution), operation for memory
accessing such as opening the [Memory] window is not allowed. Values displayed here are
dummy. Access the memory again after flash memory programming has been completed.
28. Download of Programs
Verification cannot be enabled by selecting [Perform memory verify during download]
checkbox in the [Download Module] dialog box in which download modules can be specified.
To perform verification after downloading, specify verification in the [Verify Memory] dialog
box opened by selecting [Verify Memory] from the [Debug] menu.
29. Loading Sessions
Information in [JTAG clock] of the [Configuration] dialog box cannot be saved by sessions.
The JTAG clock value becomes the initial value when starting up the emulator.
30. Connecting Two or More Emulators
If two or more emulators are to be connected to a single personal computer, the emulator that
was connected earlier should be in the break state whenever you connect another emulator.
31. Manual Navigator
Follow the procedure below to execute this program under Windows Vista® or Windows 7.
®
Work-around:
(1) Log in with administrative rights.
(2) Open the properties window for file man_navi.exe in the Manuals folder under the
installation folder for the High-performance Embedded Workshop.
(3) On the [Compatibility] tabbed page, check the [Run this program as an administrator]
box.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 184 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix E Diagnostic Test Procedure
Appendix E Diagnostic Test Procedure
For the diagnostic test procedure using the emulator test program, refer to the E10A-USB Emulator
Test Program Manual (file name: E10A-USBTME.PDF) in the ‘E10A-USB Emulator software’
CD.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 185 of 190
H8S, H8SX Family E10A-USB Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Appendix E Diagnostic Test Procedure
Page 186 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix F Repair Request Sheet
Appendix F Repair Request Sheet
Thank you for purchasing the E10A-USB emulator (HS0005KCU01H or HS0005KCU02H).
In the event of a malfunction, fill in the repair request sheet on the following pages and send it to
your distributor.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 187 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix F Repair Request Sheet
Repair Request Sheet
To Distributor
Your company name:
Person in charge:
Tel.:
Item
Symptom
1. Date and time when the malfunction
occurred
Month/Day/Year {at system initiation, in system
operation}
*Circle either of items in the braces { }.
2. Frequency of generation of the
malfunction
( ) times in ( ) {day(s), week(s), or month(s)}
3. System configuration when the
malfunction occurred
System configuration of the emulator:
*Enter the appropriate numbers in the parentheses ( )
and circle one of the three items in the braces { }.
•
E10A-USB emulator (HS0005KCU01H or
HS0005KCU02H):
Serial No.:
Revision:
The above items are written on the label for product
management at the bottom of the emulator unit; the
serial no. is the five-digit number and the revision is
the string of letters following the number.
•
Provided CD-R (HS0005KCU01SR):
Version: V.
Shown as ‘V.x.xx release xx’ on the CD-R (x:
numeral).
•
Host computer in use:
Manufacturer:
Type number:
OS: (Windows® XP, Windows Vista®, or Windows 7)
®
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 188 of 190
H8S, H8SX Family E10A-USB Emulator
Appendix F Repair Request Sheet
Item
Symptom
4. Settings when the malfunction
occurred
(1) MCU: Part number:
(2) Operating frequency:
MHz
5. Failure phenomenon
6. Error in debugging
7. Error in the diagnostic program
8. The High-performance Embedded
Workshop does not link-up with the
emulator.
Content of the error message
For errors other than the above, fill in the box below.
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Page 189 of 190
H8S, H8SX Family E10A-USB Emulator
R20UT0869EJ1400 Rev. 14.00
Aug 30, 2012
Appendix F Repair Request Sheet
Page 190 of 190
H8S, H8SX Family E10A-USB Emulator
User’s Manual (HS0005KCU01H, HS0005KCU02H)
Publication Date:
Rev. 14.00, August 30, 2012
Published by:
Renesas Electronics Corporation
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-651-700, Fax: +44-1628-651-804
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
13F, No. 363, Fu Shing North Road, Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949
Tel: +65-6213-0200, Fax: +65-6213-0300
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2012 Renesas Electronics Corporation. All rights reserved.
Colophon 1.3
H8S, H8SX Family E10A-USB Emulator
User’s Manual
R20UT0869EJ1400
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement