5-axis CNC Breakout board User Manual

5-axis CNC Breakout board User Manual

S A V E B

A

S

E

5-axis CNC Breakout board User Manual

Thank you for choosing our product, please read this manual before use.

PART 1:

Features:

1. Upgraded circuit, work more peacefully and steady than the version before.

2. Maximum support 5-axis stepper motor driver controller.

3. Two types of ways to get power, 5V DC power supply or USB port to directly get power from PC.

4. Two-stage signal processing, smooth signal transmission, powerful anti-jamming.

5. 5-input interface to define the emergency stop, limit, points in the knife, etc.

6. Relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.

7. 5-axis work LED display, visually display the working condition of the stepper driver controller.

Electrical Performance (Ambient Temperature Tj = 25 ℃):

Input Power

Compatible Stepper Motor Driver

5V DC power supply or USB port to directly get power from PC

Max 5 single axis stepper motor driver controller

Drive type

Net/Total Weight

Dimensions

Waveform And Timing:

Pulse + Direction + Enable Signal Control

About 80g/300g

90 * 82 * 15mm (L*W*H)

Interface & Pinout Definitions:

S A V E B

A

S

E

Interface Detailed Drawing:

S A V E B

A

S

E

Interface Function & connections:

S A V E B

A

S

E

When testing, check the following notes before use:

1. Check the input voltage of the breakout board (make sure 5V input voltage);

2. Understand how the breakout board works with stepper drivers;

3. Check all the wiring among all the CNC units.

Part 2: The Definition Of Each Pin

1 Defined as parallel control

PIN9 PIN1 PIN2 PIN14 PIN16 PIN3

Spindle

Enable X X Y Y

PIN7 PIN8 PIN6 PIN5 PIN4 PIN17

Z Z A A B B motor Pulse Dir Pulse Dir Pulse Dir Pulse Dir Pulse Dir

2. Hand control is defined as follows 1 ~ PIN15computer-15P interfaces and benchmarks within the

Digital ID)

P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15

B

Pulse

B

Dir

A

Dir

Z

Pulse

Y

Pulse

3. The limit is defined as 1 to 5

X -Limit Y- Limit

PLT-P10 PLT-P11

X

Pulse

X

Dir

Enable 5V/V

DD

Z- Limit

PLT-P12

5V/G

ND

A- Limit

PLT-P13

A

Pulse

Z

Dir

Y

Dir

Enable Enable

Emergency

PLT-P15

Notes: A. 5V 1A power supply, please take more than switching power supplies, power input received indicated on the map interface.

B. Spindle motor control is controlled via the parallel port PIN1. Spindle motor voltage must comply with the supply voltage range.

Part 3: The Use Of Mach3

S A V E B

A

S

E

Figure 1

Figure 1: open the MACH3 software, then select OK now mach3MILL.

Figure 2

MACH3 open the interface shown in Figure 2, the action of commonly used button above, here we configure the MACH software.

S A V E B

A

S

E

Figure 3

Figure 3: Click the “Config” menu “PORT & PIN” menu.

S A V E B

A

S

E

Figure 4

Figure4: Place on lap 1 setting can set the fundamental frequency, the parameters of the motor rotation speed. After 2 laps to set the place selected, the configuration pin definitions, as shown in

Figure 5.

Figure 5

According to the definition of the board parallel port, follow the map on the circle to indicate the definition of modification of the software settings.

S A V E B

A

S

E

Figure 6

Then select the output signals in part, as shown in Figure 6, according to insiders of the settings, set the corresponding entry.

Figure 7

Motor references about the settings in Motor turning and Setup, please set them shown as Figure 7.

Please set each Axis with the above

“Neutral values” for test: “320 steps, 600mm/min, 200 mm’s/sec/sec, 2 Step Pulse and 2 Dir Pulse”. Actually, these values can be changed to fit the motors perfectly after being tested again and again.

S A V E B

A

S

E

Figure 8

Figure 9

Finish all settings, you can click the

“Load G Code” menu and run the G code needed, as shown in

Figure 8 and Figure 9.

S A V E B

A

S

E

Figure 10

Having loaded the G code,

“RESET” can be seen flashing red, you can use mouse to click the

“RESET” make it stop flashing, then you can press the “CYCLESTART” button to run, detailed shown in Figure 10.

Contact us:

Web: http://stores.ebay.co.uk/SAVEBASE

E-mail: [email protected]

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement