Allen-Bradley PanelView Operator Terminals User Manual

Allen-Bradley
PanelView
Operator Terminals
User
Manual
Important User Information
Because of the variety of uses for the products described in this
publication, those responsible for the application and use of this
control equipment must satisfy themselves that all necessary steps
have been taken to assure that each application and use meets all
performance and safety requirements, including any applicable laws,
regulations, codes and standards.
The illustrations, charts, sample programs and layout examples
shown in this guide are intended solely for purposes of example.
Since there are many variables and requirements associated with any
particular installation, Allen-Bradley does not assume responsibility
or liability (to include intellectual property liability) for actual use
based upon the examples shown in this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the
Application, Installation and Maintenance of Solid-State Control
(available from your local Allen-Bradley office), describes some
important differences between solid-state equipment and
electromechanical devices that should be taken into consideration
when applying products such as those described in this publication.
Reproduction of the contents of this copyrighted publication, in
whole or part, without written permission of Allen-Bradley
Company, Inc., is prohibited.
Throughout this manual we use notes to make you aware of safety
considerations:
!
ATTENTION: Identifies information about practices
or circumstances that can lead to personal injury or
death, property damage or economic loss.
Attention statements help you to:
•
identify a hazard
•
avoid a hazard
•
recognize the consequences
Important: Identifies information that is critical for successful
application and understanding of the product.
PanelBuilder, PanelView, SLC, SLC 500, SLC 5/01, SLC 5/02, SLC 5/03, SLC 5/0, MicroLogix,
ControlLogix, Data Highway Plus are trademarks of Allen-Bradley Company, Inc.
PLC and PLC-5 are registered trademarks of Allen-Bradley, Inc.
Microsoft, MS-DOS and Windows are trademarks or registered trademarks of Microsoft Corporation.
x-3
Table of Contents
Table of Contents
Preface
Preface Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-1
Contents of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-2
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-3
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-3
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-3
Installing PanelView Terminals . . . . . . . . . . . . . . . . . . . . . . . .P-3
European Union Directive Compliance . . . . . . . . . . . . . . . . . .P-3
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-4
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P-4
Technical Product Assistance . . . . . . . . . . . . . . . . . . . . . . . . .P-4
Terminal Overview
Chapter 1
Intended Uses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Terminal Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
Color and Grayscale Terminals . . . . . . . . . . . . . . . . . . . . . . . .1-5
PanelView 550 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6
PanelView 600 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
PanelView 900/1000 Features. . . . . . . . . . . . . . . . . . . . . . . . .1-16
PanelView 1400 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-20
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-24
Touch Screen Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-25
Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-25
Configuration Mode Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .1-26
Terminal Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-26
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-26
Alarm List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-27
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-28
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-30
Initial Setup
Chapter 2
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Wiring and Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Connecting AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Connecting DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
Resetting the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
Power-up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Publication 2711-6.1
ii
Table of Contents
Configuring the Terminal
Chapter 3
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Application Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Accessing the Configuration Mode Menu . . . . . . . . . . . . 3-2
Selecting a Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Using a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Configuring Communications . . . . . . . . . . . . . . . . . . . . . 3-6
DH-485 Communications . . . . . . . . . . . . . . . . . . . . . . 3-6
DH+ Communications . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Remote I/O Communications . . . . . . . . . . . . . . . . . . . 3-9
ControlNet Communications . . . . . . . . . . . . . . . . . . . 3-10
DeviceNet Communications . . . . . . . . . . . . . . . . . . . 3-12
DF1 Communications . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Configuring Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Viewing Terminal Information . . . . . . . . . . . . . . . . . . . 3-17
Adjusting Screen Parameters . . . . . . . . . . . . . . . . . . . . . 3-18
Setting the Time and Date . . . . . . . . . . . . . . . . . . . . . . . 3-25
Setting up the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Using a Memory Card
Chapter 4
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supported Memory Cards . . . . . . . . . . . . . . . . . . . . . . . .
Using the Memory Card Retainer . . . . . . . . . . . . . . . . . .
Loading Application from a Memory Card . . . . . . . . . . .
Loading Application on a Memory Card . . . . . . . . . . . . .
Storing Font Files on a Memory Card . . . . . . . . . . . . . . .
Removing a Memory Card . . . . . . . . . . . . . . . . . . . . . . . .
Running Applications
4-1
4-1
4-2
4-4
4-6
4-8
4-8
Chapter 5
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Push Button Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Control Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Numeric Entry Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Screen Selectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
List Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Multistate Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Bar Graph Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Numeric Data Displays . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Message Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Time or Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Publication 2711-6.1
Table of Contents
Installing the PV550 Terminal
iii
Chapter 6
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
Installing the PV550 in a Panel . . . . . . . . . . . . . . . . . . . . .6-5
Installing the PV600 Terminal
Chapter 7
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
Installing the PV600 in a Panel . . . . . . . . . . . . . . . . . . . . .7-4
Installing the PV900/1000
Terminals
Chapter 8
Installing the PV1400
Terminal
Chapter 9
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5
Installing the PV900/PV1000 in a Panel . . . . . . . . . . . . . .8-6
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-3
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4
Installing the PV1400 in a Panel . . . . . . . . . . . . . . . . . . . .9-5
Publication 2711-6.1
iv
Table of Contents
Making Terminal
Connections
Chapter 10
Troubleshooting and
Maintenance
Chapter 11
Appendix A
Specifications
Appendix B
Messages, Codes and Self-Test Numbers
Appendix C
European Union Directive Compliance
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Wiring and Safety Guidelines . . . . . . . . . . . . . . . . . . . . 10-1
Remote I/O Terminal Connections . . . . . . . . . . . . . . . . 10-2
DH-485 Terminal Connections . . . . . . . . . . . . . . . . . . . 10-6
DH+ Terminal Connections . . . . . . . . . . . . . . . . . . . . . 10-13
RS-232 Terminal Connections . . . . . . . . . . . . . . . . . . . 10-16
ControlNet Connections . . . . . . . . . . . . . . . . . . . . . . . . 10-20
DeviceNet Terminal Connections . . . . . . . . . . . . . . . . 10-25
DF1 Terminal Connections . . . . . . . . . . . . . . . . . . . . . 10-27
Connecting a Computer or Printer to Terminal. . . . . . . 10-30
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Troubleshooting Chart . . . . . . . . . . . . . . . . . .
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Display Window . . . . . . . . . . . . . . . . . . . .
Replacing the Clock Module . . . . . . . . . . . . . . . . . . . . .
Replacing the Backlight . . . . . . . . . . . . . . . . . . . . . . . . .
Glossary
Index
Publication 2711-6.1
11-1
11-1
11-1
11-4
11-5
11-5
11-5
Preface
Preface
Read this preface to familiarize yourself with the rest of this manual.
•
contents of this manual
•
intended audience
•
conventions used
•
terminology
•
installing PanelView terminals
•
European Union Directive Compliance
•
related publications
•
technical support
Publication 2711-6.1
P-2
Preface
Contents of Manual
Publication 2711-6.1
The following table gives an overview of this manual.
Chapter
Title
Purpose
1
Terminal Overview
Describes features of the PanelView
terminals.
2
Initial Setup
3
Configuring the Terminal
Shows how to configure the terminal
using the Configuration Mode menu.
4
Using a Memory Card
Tells how to copy applications to and
from a memory card.
5
Running Applications
Describes objects common to most
applications.
6
Installing the PanelView 550
Terminal
Shows how to mount the PanelView
550 terminal in an enclosure or
panel.
7
Installing the PanelView 600
Terminal
Shows how to mount the PanelView
600 terminal in an enclosure or
panel.
8
Installing the
PanelView 900/1000 terminal
Shows how to mount the PanelView
900 or 1000 terminal in an enclosure
or panel.
9
Installing the PanelView 1400
Terminal
Shows how to mount the PanelView
1400 terminal in an enclosure or
panel.
10
Making Terminal Connections
Describes connections for the
Remote I/O, DH-485, DH+, RS-232,
DF1, ControlNet and DeviceNet versions of the PanelView terminals.
Also shows how to connect a computer or printer to terminals with an
RS-232 serial port.
11
Troubleshooting and Maintenance
Provides assistance in identifying
and correcting common operating
problems. Also gives procedures for
routine maintenance.
Describes how to apply power and
reset the PanelView terminals.
Preface
Intended Audience
P-3
No special knowledge is required to understand this manual or
operate the PanelView terminals. Before running an application, you
must know the functions of all screens and screen objects. This
information is available from the application designer.
Equipment installers must be familiar with standard panel installation
techniques.
Conventions
The manual uses the following conventions:
•
PV550 refers to the PanelView 550 terminal.
•
PV600 refers to the PanelView 600 terminal.
•
PV900 refers to the PanelView 900 terminal.
•
PV1000 refers to the PanelView 1000 terminal.
•
PV1400 refers to the PanelView 1400 terminal.
•
PanelView terminal refers to any one of the PanelView terminals.
Terminology
This manual contains some terms that may be unfamiliar. Use the
glossary of this manual for assistance.
Installing PanelView Terminals
Each terminal is shipped with installation instructions and a panel
cutout. Please follow these instructions when installing your
PanelView terminal in a panel or enclosure.
European Union Directive
Compliance
Refer to Appendix C for details on installing the PanelView terminals
in industrial environments requiring compliance with European
Union Directives.
Publication 2711-6.1
P-4
Preface
Related Publications
Refer to the following publications if necessary.
Publication
Description
2711-6.0
PanelBuilder Software User Manual
2711-6.2
Getting Started with PanelBuilder User Manual
2711-6.3
PROFIBUS DP Communications for PanelView Terminals
2711-6.0.4
DeviceNet Communications for PanelView Terminals
2711-6.10
ControlNet Communications for PanelView Terminals
2711-805
PanelView File Transfer Utility
1770-4.1
Programmable Controller Wiring and Grounding Guidelines
1770-6.2.2
Data Highway/Data Highway Plus/Data Highway-485
Cable Installation Manual
1785-5.7
Enhanced PLC-5 Programmable Controllers InstallationInstructions
For information relating to your controller, refer to the appropriate
manual.
Technical Support
Allen-Bradley offers support services worldwide, with over 75 Sales/
Support Offices, 512 authorized Distributors and 260 authorized Systems Integrators located throughout the United States alone, plus
Allen-Bradley representatives in every major country in the world.
Local Product Support
Contact your local Allen-Bradley representative for:
Technical Product Assistance
Publication 2711-6.1
•
sales and order support
•
product technical training
•
warranty support
•
support service agreements
If you need to contact Allen-Bradley for technical assistance, please
review the information in Chapter 11 on Troubleshooting first. Then
call your local Allen-Bradley representative.
Chapter
1
Terminal Overview
This chapter gives an overview of the PanelView Operator Terminals.
Intended Uses
•
intended uses
•
terminal types and features
•
applications
•
configuration mode
•
terminal messages
•
printing
•
accessories and replacement parts
You can use the PanelView operator terminals for a wide variety of
machine control and monitoring applications.
!
Terminal Types
ATTENTION: Do not use a PanelView terminal for
emergency stops or other controls critical to the safety
of personnel or equipment. Use separate hardwired
operator interface devices that do not depend on solid
state electronics. See the inside front cover of this
manual for guidelines.
PanelView terminals are available in a variety of options. Differences
are in:
•
display size and type (monochrome, grayscale, color)
•
operator input (touch screen or keypad)
•
communication port (DH-485, RS-232, Remote I/O, DH+,
ControlNet, DeviceNet, DF1)
•
RS-232 printer port support
In addition, some terminals are available with:
•
AC or DC power (L1 at the end of a catalog number indicates a
DC terminal, for example, 2711-B5A1L1, or -T9C1L1).
•
Stainless steel (L2 indicates a stainless steel terminal with AC
power, 2711-T9C1L2. L3 indicates a stainless steel terminal with
DC power, 2711-T9C1L3.)
Contact your Allen-Bradley representative for availability.
Publication 2711-6.1
1-2
Terminal Overview
PanelView 550 Monochrome Terminals
The Touch Screen version of the PanelView 550 terminal is available only
with 24V DC power. The L1 in the catalog number indicates DC power.
Operator
Input
Communication Ports
RIO
DH-485 RS-232 DH+
DeviceNet
Printer Port
RS-232
ControlNet DF1
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
2711-B5A8
2711-B5A9
2711-B5A10
2711-B5A15
2711-B5A16
2711-K5A1
2711-K5A2
ä
ä
2711-K5A3
2711-K5A5
ä
Keypad
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
2711-K5A8
2711-K5A9
2711-K5A10
2711-K5A15
2711-K5A16
2711-T5A1L1
2711-T5A2L1
ä
ä
2711-T5A3L1
2711-T5A5L1
ä
ä
ä
ä
ä
1
2711-B5A3
2711-B5A5
ä
Touch
Screen
(24V dc only)
2711-B5A1
2711-B5A2
ä
ä
Touch Screen
and Keypad
Catalog1
Number
ä
ä
ä
ä
ä
2711-T5A8L1
2711-T5A9L1
2711-T5A10L1
2711-T5A15L1
2711-T5A16L1
Add L1 to the end of a catalog number for 24V dc power.
Add L2 to the end of a catalog number for stainless steel. Not available for the touch
screen terminals.
Add L3 to the end of a catalog number for 24V dc power and stainless steel.
Stainless steel is not available for the touch screen terminals.
Publication 2711-6.1
Terminal Overview
1-3
PanelView 600 Color Terminals
Operator
Input
Communication Ports
RIO
DH-485 RS-232 DH+
DeviceNet
ä
ä
ä
ä
2711-B6C1
2711-B6C2
ä
2711-B6C3
ä
Touch Screen
and Keypad
2711-B6C5
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
2711-B6C8
2711-B6C9
2711-B6C10
2711-B6C15
2711-B6C16
2711-K6C1
2711-K6C2
ä
2711-K6C3
ä
2711-K6C5
ä
Keypad
ä
ä
ä
ä
1
Catalog1
Number
Printer Port
RS-232
ControlNet DF1
ä
ä
ä
ä
ä
2711-K6C8
2711-K6C9
2711-K6C10
2711-K6C15
2711-K6C16
L1 added to the end of a catalog number indicates 24V dc power.
PanelView 900 Monochrome Terminals
Operator
Input
Communication Ports
RIO
DH-485 RS-232 DH+
DeviceNet
ä
ä
ä
ä
2711-T9A3
2711-T9A5
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
2711-T9A8
2711-T9A9
2711-T9A10
2711-T9A15
2711-K5A16
2711-K9A1
2711-K9A2
ä
ä
2711-K9A3
2711-K9A5
ä
Keypad
ä
ä
ä
ä
1
2711-T9A1
2711-T9A2
ä
ä
Touch Screen
Catalog1
Number
Printer Port
RS-232
ControlNet DF1
ä
ä
ä
ä
ä
2711-K9A8
2711-K9A9
2711-K9A10
2711-K9A15
2711-K9A16
L1 added to the end of a catalog number indicates 24V dc power.
Publication 2711-6.1
1-4
Terminal Overview
PanelView 900 Color Terminals
Operator
Input
Communication Ports
RIO
DH-485 RS-232 DH+
DeviceNet
ControlNet
DF1
ä
ä
ä
Touch Screen
ä
ä
ä
ä
ä
ä
ä
ä
Keypad
ä
ä
ä
1
Catalog1
Number
Printer Port
RS-232
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
2711-T9C1
2711-T9C3
2711-T9C8
2711-T9C9
2711-T9C10
2711-T9C15
2711-T9C16
2711-K9C1
2711-K9C3
2711-K9C8
2711-K9C9
2711-K9C10
2711-K9C15
2711-K9C16
L1 added to the end of a catalog number indicates 24V dc power.
PanelView 1000 Color Terminals
Operator
Input
Communication Ports
RIO
DH-485 RS-232 DH+
DeviceNet
ä
ä
ä
Touch Screen
ä
ä
ä
ä
ä
ä
ä
ä
Keypad
ä
ä
ä
1
Publication 2711-6.1
Catalog1
Number
Printer Port
RS-232
ControlNet DF1
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
2711-T10C1
2711-T10C3
2711-T10C8
2711-T10C9
2711-T10C10
2711-T10C15
2711-T10C16
2711-K10C1
2711-K10C3
2711-K10C8
2711-K10C9
2711-K10C10
2711-K10C15
2711-K10C16
L1 added to the end of a catalog number indicates 24V dc power.
Terminal Overview
1-5
PanelView 1000 Grayscale Terminals
Operator
Input
Communication Ports
RIO
DH-485 RS-232 DH+
DeviceNet
ä
ä
ä
Touch Screen
ä
ä
ä
ä
ä
ä
ä
ä
Keypad
ä
ä
ä
1
Catalog1
Number
Printer Port
RS-232
ControlNet DF1
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
2711-T10G1
2711-T10G3
2711-T10G8
2711-T10G9
2711-T10G10
2711-T10G15
2711-T10G16
2711-K10G1
2711-K10G3
2711-K10G8
2711-K10G9
2711-K10G10
2711-K10G15
2711-K10G16
L1 added to the end of a catalog number indicates 24V dc power.
PanelView 1400 Color Terminals
Operator
Input
Communication Ports
RIO
DH-485 RS-232 DH+
DeviceNet
Printer Port
RS-232
ControlNet DF1
ä
ä
ä
Touch Screen
ä
ä
ä
ä
ä
ä
ä
Keypad
ä
ä
ä
ä
Color and Grayscale Terminals
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
Catalog1
Number
2711-T14C1
2711-T14C3
2711-T14C8
2711-T14C9
2711-T14C10
2711-T14C15
2711-T14C16
2711-K14C1
2711-K14C3
2711-K14C8
2711-K14C9
2711-K14C10
2711-K14C15
2711-K14C16
Color terminals support a fixed palette of 16 standard EGA colors.
Grayscale terminals support a fixed palette of 4 colors (shades of
gray). All color in an application is defined when the application is
created. Colors are not selectable at the terminal.
Publication 2711-6.1
1-6
Terminal Overview
PanelView 550 Features
This section defines features of the PanelView 550 terminals.
PanelView 550 Features (Front)
Keypad Terminal
3
4
1
2
Keypad & Touch Screen Terminal
Cell 16
Cell 1
5
6
Cell 113
Cell 128
Touch Screen Terminal
Cell 1
Cell 16
5
6
Cell 113
Publication 2711-6.1
Cell 128
Terminal Overview
1-7
#
Feature
Description
1
Function Keys
(F1 - F10)
On keypad terminals, use the function keys to initiate
functions on the terminal display. These keys may have
custom legends.
On keypad & touch screen terminals, you can initiate
functions using the function keys and/or touch screen
objects.
2
Cursor Keys
3
Numeric Entry Keys
Use the cursor keys to move the cursor in displayed
lists, to select a numeric entry object, or to enter configuration mode.
0-9
.
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
4
Keypad
Terminal Display
On keypad terminals, initiate the function of a displayed
object, such as an ON or OFF push button, by pressing
a function key (F1 - F10).
5
Touch Screen
Terminal Display
On touch screen or keypad & touch screen terminals,
initiate the function of a displayed object, such as an ON
or OFF push button, by touching the screen object.
Each interactive screen object occupies one or more of
128 cells.
On keypad & touch screen terminals, you can initiate
functions using the function keys and/or touch screen
objects.
6
Touch Cells
(Touch Screen terminal)
The 128 touch cells (16 columns x 8 rows) let you initiate functions by touching the screen. Interactive
screen objects are aligned with touch cells when the
application is created.
Publication 2711-6.1
1-8
Terminal Overview
PanelView 550 Keypad or Keypad & Touch Screen Terminals (Back)
DH-485 Version without RS-232 Port
4
5
3
2
6
7
1
AC connector shown,
DC connector looks different
11
10
8
9
DH-485 Version with RS-232 Port
18
11
10
Backlight lamp behind access cover
RS-232 Version
Remote I/O, DH+, DeviceNet, ControlNet or
DF1 Version with RS-232 Port
12
RS-232 Version
with additional RS-232 Port
18
Publication 2711-6.1
12
13, 14, 15, 16 or 17
18
Terminal Overview
1-9
#
Feature
Description
1
Power Connection Terminals
Connects to external power source.
2
Nameplate Label
Provides product information.
3
Sealing Gasket
Seals the front of the terminal to an enclosure or panel.
4
COMM LED (Green)
Indicates when communications is occurring.
5
FAULT LED (Red)
Indicates firmware or hardware faults.
6
Memory Card Slot
Accepts a memory card which stores applications.
7
Access Cover
Provides access to the replaceable backlight lamp.
8
Backlight Lamp
Light source for the display backlight. Light transmits through a fiberoptic bundle to the back of the LCD display.
9
Spare Bulb Holder
Stores a spare backlight lamp.
10
DH-485 Communication Port
Connects to an SLC controller, DH-485 network, or Wallmount
Power Supply (Cat. No. 1747-NP1).
11
DH-485
Programming Connector
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC
programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
12
RS-232 Communication Port
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for
point-to-point DH-485 communications. Also connects to the RS232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
13
Remote I/O Port
Connects to a scanner or sub-scanner on a Remote I/O network.
14
DH+ Communication Port
Connects to a PLC or SLC 5/04 controller on a DH+ link.
15
DeviceNet Connector
Connects to a DeviceNet network.
16
ControlNet Connectors
Connects to a ControlNet network.
17
DF1 Communication Port
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
18
RS-232 Printer/
File Transfer Port
Connects to a printer.
On Remote I/O, DH+, DeviceNet and ControlNet terminals, this port
also connects to the RS-232 port of a computer for transferring
applications.
Publication 2711-6.1
1-10
Terminal Overview
PanelView 550 Touch Screen Terminal Features (Back)
DH-485 Version without RS-232 Port
5
4
6
3
2
7
1
11
10
9
8
DH-485 Version with RS-232 Port
Backlight lamp behind access cover
9
11
10
18
RS-232 Version
Remote I/O, DH+, DeviceNet, ControlNet or
DF1 Version with RS-232 Port
12
RS-232 Version with additional RS-232 Port
12
Publication 2711-6.1
18
18
13, 14, 15, 16 or 17
Terminal Overview
1-11
#
Feature
Description
1
Power Connection Terminals
Connects to external DC power source.
2
Sealing Gasket
Seals the front of the terminal to an enclosure or panel.
3
FAULT LED (Red)
Indicates firmware or hardware faults.
4
COMM LED (Green)
Indicates when communications is occurring.
5
Nameplate Label
Provides product information.
6
Memory Card Slot
Accepts a memory card which stores applications.
7
Reset Button
Resets the terminal.
8
Access Cover
Provides access to the replaceable backlight lamp.
9
Backlight Lamp
Light source for the display backlight.
10
DH-485 Communication Port
Connects to an SLC controller, DH-485 network, or Wallmount
Power Supply (Cat. No. 1747-NP1).
11
DH-485
Programming Connector
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC
programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
12
RS-232 Communication Port
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for
point-to-point DH-485 communications. Also connects to the RS232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
13
Remote I/O Port
Connects to a scanner or sub-scanner on a Remote I/O network.
14
DH+ Communication Port
Connects to a PLC or SLC 5/04 controller on a DH+ link.
15
DeviceNet Connector
Connects to a DeviceNet network.
16
ControlNet Connectors
Connects to a ControlNet network.
17
DF1 Communication Port
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
18
RS-232 Printer/
File Transfer Port
Connects to a printer.
On Remote I/O, DH+, DeviceNet or ControlNet terminals, this port
also connects to the RS-232 port of a computer for transferring
applications.
Publication 2711-6.1
1-12
Terminal Overview
PanelView 600 Features
This section defines features of the PanelView 600 terminals.
PanelView 600 Features (Front)
Keypad Terminal
3
4
1
2
Touch Screen Terminal
Cell 1
Cell 16
5
6
Cell 113
Publication 2711-6.1
Cell 128
Terminal Overview
1-13
#
Feature
Description
1
Function Keys (F1 - F10)
Use the function keys on keypad terminals to initiate
functions on the terminal display. These keys may have
custom legends.
On the keypad & touch screen terminals, you can initiate functions using the function keys and/or touch
screen objects.
2
Cursor Keys
Use the cursor keys to move the cursor in displayed
lists, to select a numeric entry object, or to enter configuration mode.
3
Numeric Entry Keys
0-9
.
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
4
Keypad Terminal Display
On keypad terminals, initiate the function of a displayed
object, such as an ON or OFF push button, by pressing
a function key (F1 - F10).
5
Touch Screen
Terminal Display
On keypad & touch screen terminals, initiate the function of a displayed object, such as an ON or OFF push
button, by touching the screen object. Each interactive
screen object occupies one or more of 128 cells.
On touch screen & keypad terminals, you can initiate
functions, using the function keys and/or touch screen
objects.
6
Touch Cells
(Touch Screen terminal)
The 128 touch cells (16 columns x 8 rows) let you initiate functions by touching the screen. Interactive
screen objects are aligned with touch cells when the
application is created.
Publication 2711-6.1
1-14
Terminal Overview
PanelView 600 Terminal Features (Back)
Remote I/O, DH+, DeviceNet, ControlNet
or DF1 Version with RS-232 Port
4
10, 11, 12, 13 or 14
15
DH-485 Version
3
2
7
8
1
DH-485 Version with RS-232 Port
7, 8, 9, 10
11, 12, 13, 14, 15
6
15
7
8
RS-232 Version
9
Publication 2711-6.1
5
RS-232 Version with additional RS-232 Port
15
9
Terminal Overview
1-15
#
Feature
Description
1
Power Connection Terminals
Connects to external power source.
2
Nameplate Label
Provides product information.
3
Memory Card Slot
Accepts a memory card which stores applications.
4
Sealing Gasket
Seals the front of the terminal to an enclosure or panel.
5
FAULT LED (Red)
Indicates firmware or hardware faults.
6
COMM LED (Green)
Indicates when communications is occurring.
7
DH-485 Communication Port
Connects to an SLC controller, DH-485 network, or Wallmount
Power Supply (Cat. No. 1747-NP1).
8
DH-485
Programming Connector
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC
programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
9
RS-232 Communication Port
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for
point-to-point DH-485 communications. Also connects to the RS232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
10
Remote I/O Port
Connects to a scanner or sub-scanner on a Remote I/O network.
11
DH+ Communication Port
Connects to a PLC or SLC 5/04 controller on a DH+ link.
12
DeviceNet Connector
Connects to a DeviceNet network.
13
ControlNet Connectors
Connects to a ControlNet network.
14
DF1 Communication Port
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
15
RS-232 Printer/
File Transfer Port
Connects to a printer.
On Remote I/O, DH+, DeviceNet or ControlNet terminals, this port
also connects to the RS-232 port of a computer for transferring
applications.
Publication 2711-6.1
1-16
Terminal Overview
PanelView 900/1000 Features
This section defines features of the PanelView 900 and 1000
terminals.
PanelView 900/1000 Terminal Features (Front)
Keypad Terminal
4
3
1
2
Touch Screen Terminal
Cell 1
5
6
Cell 24
Cell 361
Cell 384
Publication 2711-6.1
Terminal Overview
1-17
#
Feature
Description
1
Function Keys (F1 - F16)
Use the function keys on keypad terminals to initiate
functions on the terminal display. These keys may have
custom legends.
2
Cursor Keys
Use the cursor keys to move the cursor in displayed
lists, to select a numeric entry object or to enter configuration mode.
3
Numeric Entry Keys
0-9
.
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
4
Keypad Terminal Display
On keypad terminals, initiate the function of a displayed
object, such as an ON or OFF push button, by pressing
a function key (F1 - F16).
5
Touch Screen
Terminal Display
On touch screen terminals, initiate the function of a displayed object, such as an ON or OFF push button, by
touching the screen object. Each interactive screen
object occupies one or more of 384 cells.
6
Touch Cells
(Touch Screen terminal)
The 384 touch cells (24 columns x 16 rows) let you initiate functions by touching the screen. Interactive
screen objects are aligned with touch cells when the
application is created.
Publication 2711-6.1
1-18
Terminal Overview
PanelView 900/1000 Terminal Features (Back)
Remote I/O, DH+, DF1, DeviceNet,
or ControlNet Version with RS-232 Port
4
Back View
Touch Screen Terminal
3
11, 12, 13, 14 or 15
16
5
2
DH-485 Version
6
1
8
9
8, 9, 10
11, 12, 13, 14, 15, 16
7
DH-485 Version with RS-232 Port
4
Back View
Keypad Terminal
16
8
9
3
RS-232 Version
5
2
6
10
1
RS-232 Version with additional RS-232 Port
16
Publication 2711-6.1
10
8, 9, 10
11, 12, 13, 14, 15, 16
7
Terminal Overview
1-19
#
Feature
Description
1
Power Connection Terminals
Connects to external power source.
2
Nameplate Label
Provides product information.
3
Reset Button
Resets the terminal.
4
Sealing Gasket
Seals the front of the terminal to an enclosure or panel.
5
Memory Card Slot
Accepts a memory card which stores applications.
6
FAULT LED (Red)
Indicates firmware or hardware faults.
7
COMM LED (Green)
Indicates when communications is occurring.
8
DH-485 Communication Port
Connects to an SLC controller, DH-485 network, or Wallmount
Power Supply (Cat. No. 1747-NP1).
9
DH-485
Programming Connector
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC
programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
10
RS-232 Communication Port
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for
point-to-point DH-485 communications. Also connects to the RS232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
11
Remote I/O Port
Connects to a scanner or sub-scanner on a Remote I/O network.
12
DH+ Communication Port
Connects to a PLC or SLC 5/04 controller on a DH+ link.
13
DeviceNet Connector
Connects to a DeviceNet network.
14
ControlNet Connectors
Connects to a ControlNet network.
15
DF1 Communication Port
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
16
RS-232 Printer/
File Transfer Port
Connects to a printer.
On Remote I/O, DH+, DeviceNet and ControlNet terminals, this port
also connects to the RS-232 port of a computer for transferring
applications.
Publication 2711-6.1
1-20
Terminal Overview
PanelView 1400 Features
This section defines features of the PanelView 1400 terminals.
PanelView 1400 Terminal Features (Front)
Keypad Terminal
3
4
1
2
Touch Screen Terminal
Cell 1
Cell 24
5
6
Cell 361
Publication 2711-6.1
Cell 384
Terminal Overview
1-21
#
Feature
Description
1
Function Keys (F1 - F21)
Use the function keys on keypad terminals to initiate
functions on the terminal display. These keys may have
custom legends.
2
Cursor Keys
Use the cursor keys to move the cursor in displayed
lists, to select a numeric entry object, or to enter configuration mode.
3
Numeric Entry Keys
0-9
.
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
4
Keypad Terminal Display
On keypad terminals, initiate the function of a displayed
object, such as an ON or OFF push button, by pressing
a function key (F1 - F21).
5
Touch Screen
Terminal Display
On touch screen terminals, initiate the function of a displayed object, such as an ON or OFF push button, by
touching the screen object. Each interactive screen
object occupies one or more of 384 cells.
6
Touch Cells
(Touch Screen terminal)
The 384 touch cells (24 columns x 16 rows) let you initiate functions by touching the screen. Interactive
screen objects are aligned with touch cells when the
application is created.
Publication 2711-6.1
1-22
Terminal Overview
PanelView 1400 Terminal Features (Back and Sides)
Remote I/O, DH+, DeviceNet, ControlNet
or DF1 Version with RS-232 Port
18
1
17
16
15
7, 8, 9
10, 11, 12
13, 14, 15
2
10, 11, 12, 13 or 14
DH-485 Version with RS-232 Port
6
5
4
3
Left Side
7
8
15
19
RS-232 Version with additional RS-232 Port
Right Side
9
15
20
Publication 2711-6.1
Terminal Overview
1-23
#
Feature
Description
1
Brightness Control
Adjusts the brightness of the color display.
2
Contrast Control
Adjusts the contrast of the color display.
3
Nameplate Label
Provides product information.
4
FAULT LED (Red)
Indicates firmware or hardware faults.
5
COMM LED (Green)
Indicates when communications is occurring.
6
Power Connection Terminals
Connects to external power source.
7
DH-485 Communication Port
Connects to an SLC controller, DH-485 network, or Wallmount
Power Supply (Cat. No. 1747-NP1).
8
DH-485
Programming Connector
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC
programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
9
RS-232 Communication Port
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for
point-to-point DH-485 communications. Also connects to the RS-232
serial port of a computer for transferring applications.
10
Remote I/O Port
Connects to a scanner or sub-scanner on a Remote I/O network.
11
DH+ Communication Port
Connects to a PLC or SLC 5/04 controller on a DH+ link.
12
DeviceNet Connector
Connects to a DeviceNet network.
13
ControlNet Connector
Connects to a ControlNet network.
14
DF1 Communication Port
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
15
RS-232 Printer/
File Transfer Port
Connects to a printer. On Remote I/O, DH+, DeviceNet or ControlNet
terminals, this port also connects to the RS-232 port of a computer
for transferring applications.
16
Memory Card Eject Button
Ejects memory card from slot.
17
Memory Card Slot
Accepts a memory card which stores applications.
18
Sealing Gasket
Seals the front of the terminal to an enclosure or panel.
19
Reset Button
Resets the terminal.
20
CRT Board Adjustments
See the warning below.
!
ATTENTION: Only qualified service technicians
should access the CRT board adjustments. Failure to
follow this caution could result in electrical shock, a
misadjusted monitor, or a damaged monitor.
Publication 2711-6.1
1-24
Terminal Overview
Applications
PanelView terminals operate with custom designed applications. The
first time you power on the terminal, (no application file loaded), the
terminal displays the Configuration Mode menu. Chapter 3 describes
the terminal functions you can configure from this menu.
Note: Remote I/O terminals provide an out-of-box application for
setting Remote I/O communication parameters.
If an application is loaded, the terminal displays the application’s
start-up screen.
Note: The application designer is responsible for documenting the
operation of the application and selecting a startup screen.
How the terminal operates depends on the application and the type of
terminal (touch screen or keypad).
Publication 2711-6.1
Terminal Overview
1-25
Touch Screen Operation
Applications for touch screen terminals are controlled by touching
screen objects.
Keypad Operation
Applications for keypad terminals are controlled by pressing function
keys that correspond to screen objects. Data is entered manually using
the numeric entry keys.
A function key legend kit is available for each terminal to create
custom labels for the function keys. See the accessories at the end of
this chapter.
!
ATTENTION: Do not press multiple touch screen
objects or multiple function keys at the same time. This
may result in unintended operation.
Publication 2711-6.1
1-26
Terminal Overview
Configuration Mode Menu
You can configure terminal functions from the Configuration Mode
menu including:
•
select a language
•
upload/download applications with a memory card
•
set or display serial communication parameters
•
select preset values
•
obtain terminal and application information
•
adjust screen parameters
•
set time and date
•
set printer parameters (for terminals with an RS-232 printer port)
•
return to run mode
Chapter 3 describes how to enter configuration mode and the
operations you can perform the Configuration Mode menu.
Terminal Messages
Terminals messages display:
•
status of an operation
•
minor faults, errors, or numeric entry mistakes
•
operator prompts
Appendix B describes terminal messages and provides a list of
recommended actions.
Printing
PanelView terminals equipped with an RS-232 printer port can print:
•
triggered messages in a message display
•
triggered states of a multistate indicator
•
alarm messages
•
alarm list
Print attributes for objects are defined in the application.
Any printer that supports the IBM enhanced character set can be
connected to the RS-232 printer port of a PanelView terminal.
Publication 2711-6.1
Terminal Overview
Alarm List
1-27
PanelView terminals support an Alarm List queue to store
information on triggered alarms. The Alarm List stores a maximum of
100 alarms or as many as the terminal can hold in nonvolatile RAM.
The number of alarms stored in the list is configured using the
PanelBuilder software.
The Alarm List stores the following data for each alarm:
•
acknowledge indicator
•
alarm date and time
•
acknowledge date and time
•
alarm trigger value
•
alarm text including variables
The Alarm List is cleared:
•
when an application is downloaded to the terminal
•
when the terminal is reset or power is cycled
The Alarm List object may appear on the Alarm Banner or other
application screens. The data that displays in the Alarm List is
configured using the PanelBuilder Software.
Publication 2711-6.1
1-28
Terminal Overview
Accessories
Software
Catalog No.
2711-ND3
550
600
900
1000
1400
ä
ä
ä
ä
ä
Description
Windows software required for creating PanelView applications on a personal computer.
Function Key Legend Kits
Catalog No.
2711-NF1
550
600
900
1000
1400
ä
Description
5 legend inserts with key labels F1-F10 on one
side. Use blank side to create custom labels.
2711-NF2A
ä
1 legend insert for PV900 keypad (monochrome) terminal with key labels F1-F16 on one
side. Use blank side to create custom labels.
2711-NF2C
ä
1 legend insert for PV900 keypad (color) terminal with key labels F1-F16 on one side. Use
blank side to create custom labels.
ä
2711-NF4
1 legend insert with key labels F1-F10 on one
side. Use blank side to create custom labels.
ä
2711-NF5
ä
2711-NF6
2 legend inserts. One has key labels F1-F16;
the other has key labels F17-F21. Use blank
sides to create custom labels.
1 legend insert with key labels F1-F16. Use
blank side to create custom labels.
Memory Cards and Retainer
Catalog No.
Publication 2711-6.1
Description
550
600
900
1000
1400
2711-NM11
ä
ä
ä
ä
ä
256K memory card for storing applications.
2711-NM12
ä
ä
ä
ä
1M flash memory card for storing applications.
2711-NM13
ä
ä
ä
ä
ä
2M flash memory card for storing applications.
2711-NM14
ä
ä
ä
ä
ä
4M flash memory card for storing applications.
2711-NM22
ä
ä
ä
ä
ä
2M flash ATA card for storing applications and
font files.
2711-NM24
ä
ä
ä
ä
ä
4M flash ATA card for storing applications and
font files.
2711-NM26
ä
ä
ä
ä
ä
6M flash ATA card for storing applications and
font files.
2711-NMCC
ä
ä
ä
ä
2711-NMCD
ä
Secures memory card in all terminals except
the PV1400 and PV550 touch screen. Prevents
electrostatic discharge.
Secures memory card in 550 touch screen terminal and prevents electrostatic discharge.
Terminal Overview
1-29
Antiglare Overlay
Self-adhesive filters are available to minimize the reflection of terminal displays.
Catalog No.
550
2711-NV4
ä
2711-NV4T (Touch Screen Terminals)
ä
600
900
2711-NV3K (Keypad)
ä
2711-NV3T (Touch Screen Terminals)
ä
1000
1400
ä
2711-NV5
ä
2711-NV7K (Keypad Terminals)
ä
2711-NV7T (Touch Screen Terminals)
2711-NV6K (Keypad Terminals)
ä
2711-NV6T (Touch Screen Terminals)
ä
DH-485 Operating and Programming Cables
Catalog No.
Description
1747-PIC
Personal Computer Interface Converter converts RS-232 signals to/from
RS-485 signals. Use to transfer applications between a DH-485 terminal
and a computer.
1747-C10
1.83 meter (6 foot) cable connects a DH-485 terminal to an SLC or DH-485
network.
1747-C11
0.30 meter (1 foot) cable connects a DH-485 terminal to an SLC or DH-485
network.
1747-C20
6.1 meter (20 foot) cable connects a DH-485 terminal to an SLC or DH-485
network.
1747-CP3
45 cm (17.7 inch) cable connects an RS-232 terminal to an AIC+ (Port1)
through a null modem adapter.
1761-CBL-AP00
45 cm (17.7 inch) cable connects an RS-232 terminal to an AIC+ (Port2)
through a null modem adapter.
1761-CBL-AC00
3 meter (9.8 foot) cable connects an RS-232 terminal to an AIC+ (Port1)
through a null modem adapter.
1761-CBL-PM02
2 meter (6.5 foot) cable connects an RS-232 terminal to an AIC+ (Port2)
through a null modem adapter.
1761-CBL-AS03
3 meter (9.8 foot) cable connects a DH-485 terminal to an AIC+ (Port3).
1761-CBL-AS09
9.9 meter (29.5 foot) cable connects a DH-485 terminal to an AIC+ (Port3).
PanelView File Transfer Utility
Catalog No.
2711-ND7
Description
Transfers .PVA files between a DH-485 terminal and a computer from the
DOS environment. Does not require Windows.
Power Supply and Link Couplers
The following items are available for all DH-485 PanelView terminals.
Catalog No.
Description
1747-NP1
Wallmount Power supply provides power for DH-485 communications when
an SLC or network is not connected.
1747-AIC
AIC Link Coupler links devices on a DH-485 network.
1747-NET-AIC
AIC+ Link Coupler links devices on a DH-485 network including MicroLogix.
Publication 2711-6.1
1-30
Terminal Overview
RS-232 Cables
Catalog No.
Description
2711-NC13
5 meter (16.4 foot) connects an RS-232 terminal to the Channel 0 port of an
SLC 5/03 controller or the RS-232 port of a computer or printer.
2711-NC14
10 meter (32.7 foot) cable connects an RS-232 terminal to the Channel 0
port of an SLC 5/03 controller or the RS-232 port of a computer or printer.
2706-NC13
3 meter (10 ft) cable connects an RS-232 terminal to an SLC 5/03 controller
or the RS-232 port of a computer or printer.
Remote I/O Cable
Catalog No.
Description
1770-CD
Replacement Parts
Shielded, 3-conductor cable (Belden 9463) for connecting a Remote I/O terminal to a Remote I/O network.
Backlight Lamps
Catalog No.
2711-NL1
550
600
900
ä
Halogen backlight lamp for all PV550 terminals.
Provides backlighting for LCD display.
ä
2711-NL2
Backlight for PV900 color terminal.
ä
2711-NL3
Description
1000
Backlight for PV600 color terminal.
ä
2711-NL4
Backlight for PV1000 color terminal.
Real Time Clock Modules
Catalog No.
550
2711-NB2
ä
2711-NB3
ä
2711-NB4
ä
600
900
1000
1400
Description
Real time clock module for PV550 (Series D or
earlier). Does not apply to the PV550 touch
screen terminals. Contains lithium battery.
ä
ä
ä
ä
Real time clock module for PV600, PV900,
PV1000, PV1400 or PV550 (Series E or later).
Does not apply to PV550 touch screen terminals. Contains lithium battery.
Real time clock module for PV550 touch screen
only terminals. Contains lithium battery.
Panel Mount Clips and Studs
Catalog No.
550
600
900
1000
1400
ä
2711-NP1
ä
2711-NP2
ä
ä
2711-NP3
Description
10 panel mount clips for PV1400 terminal.
6 panel mount clips for PV600, PV900 or
PV1000 terminals.
ä
Optional panel mount studs (18) for PV1400 terminals.
Remote I/O Connector
Publication 2711-6.1
Catalog No.
550
600
900
1000
1400
Description
22112-046-03
ä
ä
ä
ä
ä
Terminal block connector plugs into Remote I/O
port of Remote I/O terminals.
Chapter
2
Initial Setup
Chapter Objectives
Wiring and Safety Guidelines
This chapter provides information on:
•
wiring and safety guidelines
•
connecting AC or DC power
•
resetting the terminal
•
power-up sequence
Use publication NFPA 70E, Electrical Safety Requirements for
Employee Workplaces when wiring the PanelView terminals. In
addition to the NFPA general guidelines:
•
connect the terminal to its own branch circuit.
The input power should be protected by a fuse or circuit breaker
rated at no more than 15 Amps.
•
route incoming power to the PanelView terminal by a separate
path from the communications cable.
!
•
ATTENTION: Do not run signal wiring and power
wiring in the same conduit.
where power and communication lines must cross, they should
cross at right angles. Communication lines can be installed in the
same conduit as low level DC I/O lines (less than 10 volts).
Publication 2711-6.1
2-2
Initial Setup
Connecting AC Power
Below are AC electrical ratings for the PanelView terminals. The
PV550 touch screen only terminal is available only with DC power,
not AC power.
Terminal Type
Supply Voltage
Power Consumption
PV550
85 to 264V ac, 47 to 63 Hz
45 VA maximum
PV600
85 to 264V ac, 43 to 63 Hz
60 VA maximum
PV900M/PV900C
85 to 264V ac, 47 to 63 Hz
110 VA maximum
PV1000G/PV1000C
85 to 264V ac, 47 to 63 Hz
100 VA maximum
PV1400
85 to 264V ac, 43 to 63 Hz
200 VA maximum
!
ATTENTION: Do not apply power to the PanelView
terminal until all wiring connections have been made.
Failure to do so may result in electrical shock.
AC Power Connections
The PanelView terminals are IEC 1131-2 Equipment Class I devices
and require you to connect the GND (Ground) or
(Protective
Earth) terminal to an earth conductor.
!
ATTENTION: The PanelView terminals are designed
for safe use when installed in a NEMA Type 12, 13, 4X
(indoor use only), IP54 or IP65 rated enclosure.
!
ATTENTION: Explosion Hazard - Do not connect or
disconnect equipment while circuit is live unless area
is known to be non-hazardous.
To connect power to the AC versions of the PanelView terminals:
1. Secure AC power wires to the L1 and L2N terminal block screws.
2. Secure the Earth Ground/Protective Earth wire to the GND or the
screw on the terminal block.
!
ATTENTION: Improper wiring of the power
terminals may result in voltage at the communication
connector shells. Refer to the figure below when wiring.
3. Apply power to the terminal
Publication 2711-6.1
Initial Setup
2-3
PanelView 550 Terminal
120/240V ac, 3 Wire,
U.S. Color Code
L1
L2N
120/240V ac, 3 Wire,
European Harmonized Color Code
GND
L1
Black (Line)
Brown (Line)
White (Neutral)
Blue (Neutral)
L2N
GND
Green (Earth Ground)
Green/Yellow (Protective Earth)
To Power Source
To Power Source
Publication 2711-6.1
2-4
Initial Setup
PanelView 900/1000 Terminal
Power Terminal
Block (fixed)
120/240V ac, 3 Wire
European Harmonized Color Code
120/240V ac, 3 Wire,
U.S. Color Code
L1
L2N
GND/PE
L1
L2N
GND/PE
Brown (Line)
Blue (Neutral)
Green/Yellow
(Protective Earth)
Black (Line)
White (Neutral)
Green (Earth Ground)
To Power Source
To Power Source
PanelView 1400 Terminal
Screwdriver Slot
Power Terminal Block (fixed)
120/240V ac, 3 Wire,
U.S. Color Code
GND/PE
120/240V ac, 3 Wire
European Harmonized Color Code
GND/PE
L2/N
L2/N
L1/L
L1/L
Green (Earth Ground)
White (Neutral)
Black (Line)
Publication 2711-6.1
Green/Yellow (Protective Earth)
Blue (Neutral)
Brown (Line)
Initial Setup
Connecting DC Power
2-5
The L1 versions (Cat. No. 2711-K5A1L1, -T9C1L1) of the PV550,
PV600, PV900, and PV1000 terminals connect to a 24V dc power
source.
The table below shows the electrical ratings for the DC versions of
the terminals. Electronic circuitry and an internal fuse protect the
terminals from reverse polarity and over-voltage conditions
Terminal Type
Supply Voltage
(24V dc nominal)
Power Consumption
PV550
18 to 30V dc
18 Watts max. (0.75A @ 24V dc)
PV550
(touch only)
18 to 32V dc
18 Watts max. (0.75A @ 24V dc)
PV600
18 to 32V dc
34 Watts max. (1.4A @ 24V dc)
PV900M
18 to 30V dc
58 Watts max. (2.5A @ 24V dc)
PV900C
18 to 32V dc
50 Watts max. (2.1A @ 24V dc)
PV1000G
18 to 32V dc
40 Watts max. (1.7A @ 24V dc)
PV1000C
18 to 32V dc
50 Watts max. (2.1A @ 24V dc)
!
ATTENTION: Do not connect the PanelView
terminal to an AC power source. Connecting to an AC
power source may damage the terminal.
Do no
!
!
ATTENTION: The PanelView terminals are designed
for safe use when installed in a NEMA Type 12, 13,
14X (indoor use only), IP54 or IP65 rated enclosure.
ATTENTION: Use only a safety extra-low voltage
(SELV) power supply as a source for the PanelView
550 touch screen terminal. A SELV power supply does
not exceed 42.4V dc.
Publication 2711-6.1
2-6
Initial Setup
DC Power Connections
Connect the power source to the terminal at the 3-screw terminal
block (fixed).
To connect power to the DC versions of the PanelView terminals:
1. Secure the DC power wires to the terminal block screws.
2. Secure the Earth Ground wire to the correct terminal block screw.
!
ATTENTION: Explosion Hazard - Do not connect or
disconnect equipment while circuit is live unless area
is known to be non-hazardous.
!
ATTENTION: Do not apply power to the PanelView
terminal until all wiring connections have been made.
Failure to do so may result in electrical shock.
3. Apply 24V dc power to the terminal.
PanelView 550/600 Terminal
Power Terminal
Block (fixed)
Power Terminal
Block (fixed)
+
-
+
Earth Ground
DC Negative
DC Positive
Publication 2711-6.1
PanelView 900 Keypad Terminal
Earth Ground
DC Negative
DC Positive
Initial Setup
Resetting the Terminal
2-7
Resetting the terminal re-initializes the PanelView terminal (same as
cycling power).
To reset the PV550 (keypad, keypad & touch screen) and PV600:
Simultaneously press the Left arrow , Right arrow
keys. The terminal performs its powerup sequence.
, and Enter ↵
The sequence in which keys are pressed (while running an
application), determines what appears after the reset.
•
If you press the Left and Right arrow keys before the Enter
↵ key, the Configuration Mode menu appears.
•
If you press the Enter ↵ key before the arrow keys, the terminal
runs the loaded application.
To reset the PV550 (touch screen)/PV900/PV1000/PV1400:
•
Use a narrow non-conductive tool to press the reset button shown
below. The terminal performs its powerup sequence.
!
ATTENTION: Use a nonconducting object to press
the Reset button. Do not use a conducting object such
as a paper clip which may damage the terminal. Do not
use the tip of a pencil, graphite may damage the
terminal.
PanelView 900/1000
PanelView 1400
Reset Button
On the PV550 touch screen terminals, the Reset button is located on the right,
below the Memory Card slot.
Publication 2711-6.1
2-8
Initial Setup
Power-up Sequence
When resetting or applying power to a PanelView terminal, the
terminal runs a series of self-tests. The initial display shows copyright
information and the status of each self-test number. See Appendix B
for a description of the self-test numbers.
COPYRIGHT ALLEN-BRADLEY COMPANY
1999, ALL RIGHTS RESERVED VXX.XX
TESTING VERIFICANADO PRUFEN
VERIFICATION AUTOTEST
2
Self-test Number
For DH-485 and RS-232 Terminals
•
If an application is loaded, the terminal displays either the screen
that was present prior to reset or power down, or the startup
screen.
•
If an application is not loaded, the Configuration Mode menu
appears.
Function keys do not
appear on touch
screen terminals.
PV900 Keypad Terminal
Note: On PV550/600 terminals, the Reset Video Button is F9.
Publication 2711-6.1
Initial Setup
2-9
For Remote I/O Terminals
An out-of-box application screen opens allowing you to set Remote
I/O parameters for the terminal. This screen is only available for
initial setup. Once an application is downloaded, the Remote I/O
setup screen is erased.
The table on the next page defines the Remote I/O Parameters.
0
PV550 Terminal
PanelView 900 Keypad Terminal
Publication 2711-6.1
2-10
Initial Setup
Press this function key on:
To set this RIO Parameter
Description
Options
F1
Rack #
Rack address of terminal on RIO network.
On PV550/600: Press ↵ to open the
scratchpad. Enter the rack address
and press ↵ again.
On PV900/PV1000/PV1400: Press
F1 to set the rack #, then use the up
and down arrow keys to select an
address.
0 to 76
F1
F2
Rack Size
Rack size of terminal. Each key press
displays a different size. The terminal
occupies a single rack.
1/4, 1/2, 3/4, Full
F2
F3
Starting Module Group
Starting module group number of the
terminal in the assigned rack. Each
key press displays a different module
group.
0,1 2,3 4,5 6,7
F3
F4
Pass-Through Enabled
Enables or Disables Pass-Through,
which lets you transfer applications
between a computer on a DH+ link
and a terminal on a Remote I/O link.
A PLC-5 controller passes data
between the networks.
Yes or No
F4
F5
Last Chassis
Specifies whether the terminal occupies the last module group in the
assigned rack (applies only to PLC2
controllers).
Yes or No
Block Transfer Timeout
Timeout value for block transfers.
Each key press toggles a value.
0 to 60 seconds
(0 is the default)
Baud Rate
Baud rate at which the terminal will
communicate on the RIO network.
Baud Max. Cable
Length
57.6K 10,000 ft
115.2K 5,000 ft
230.4K 2,500ft
550/600
900/1000/1400
↵
F5
F6
Publication 2711-6.1
F6
Chapter
3
Configuring the Terminal
Chapter Objectives
Application Settings
This chapter tells how to use the Configuration Mode menu to
configure terminal settings and perform operations including how to:
•
access the Configuration Mode menu
•
select a language
•
use a memory card
•
configure communications (DH485, DH+, Remote I/O,
ControlNet, DeviceNet, DF1)
•
configure presets
•
view terminal information
•
set the time and date
•
adjust display parameters
•
set up the printer
Configuration parameters are set from the terminal or from the
PanelBuilder software when creating the application. Settings
downloaded with the application have priority over terminal settings
if the following option is enabled in the Terminal Setup dialog of the
PanelBuilder software.
x
Use Downloaded configuration settings
In addition, the application may allow the controller to change the
following while the application is running:
•
time and date
•
current display screen
•
piloted control lists
Publication 2711-6.1
3-2
Configuring the Terminal
Accessing the
Configuration Mode Menu
The Configuration Mode menu appears on powerup if an application
is not loaded or if the menu was last displayed prior to a reset or
power down.
To access Configuration Mode on keypad terminals:
If an application is running, simultaneously press the Left
Right arrow keys on the terminal keypad.
and
To access Configuration Mode on touch screen terminals:
•
press the Goto Config. Screen button on an application screen or
•
press the filled box in the lower right corner of the screen during
powerup.
Note: Most of the screens in this chapter are for the PanelView 900
keypad terminal. The screens for other terminals are similar. On
keypad terminals you press terminal function keys to modify settings.
On touch screen terminals, you press the screen field or button.
Function keys do not
appear on touch
screen terminals.
Note: On PV550/PV600 terminals, the Reset Video button is F9.
Operations List
Select an operation using the Up
or Down
Enter ↵ key (keypad terminals) or press
to enter the selection.
arrow keys. Press the
(touch screen terminals)
Language [F8]
Displays the language menu.
Run Mode [F2]
Runs the loaded application.
Reset Video [F15] or [F9]
Resets the video to default settings. The reset video function is useful
if the screen is set to non-viewable settings.
Publication 2711-6.1
Configuring the Terminal
3-3
Comm and Fault LED
The 2 LEDs on the Configuration Mode menu indicate the operating
state of the terminal. The operating states vary for each
communication protocol.
DH-485/DH+
LED Indicators
Comm
Fault
Remote I/O
LED Indicators
Comm
Fault
This pattern
Indicates
Solid Fill
Normal operating state
Blinking
No communications
Flashing
When power is first applied (momentarily)
No Fill
Normal operating state
Blinking
Hardware is functioning but no application
file is loaded or the current application is
corrupt.
This pattern
Indicates
Solid Fill
Normal operating state
No Fill
No communications
Blinking
PLC controller is in program mode
Flashing
When power is first applied (momentarily)
No Fill
Normal operating state
Blinking
Hardware is functioning but no application
file is loaded or the current application is
corrupt.
Publication 2711-6.1
3-4
Configuring the Terminal
Selecting a Language
Press the Language button, [F8] key, from the Configuration Mode
menu to display the Language Selection screen.
Choisir Français
Deutsches Meün auswãhlen
Scagliere Italiano
Escoger Español
Select English
FIN
EXIT
USCITA
SALIR
EXIT
The terminal supports 5 languages:
•
French
•
German
•
Italian
•
Spanish
•
English
Language List
Select a language using the up or down arrow keys. All configuration
screens and terminal messages will be displayed in the selected
language.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
Using a Memory Card
3-5
Select Memory Card from the Configuration Mode menu to transfer
applications between a memory card and the terminal. Chapter 4
describes the transfer procedure.
Valid Card Inserted
F1
Memory
Card
Listing
F8
Disconnect
Card
APPLICATIONS ON CARD
\*.PVA
############
F2 Restore from Card
F3 Save to Card
F4 Erase / Format Card
EXIT
F16
Memory Card Listing [F1]
Displays the file names of applications on the memory card. Only 1
file name is displayed at a time. Press the Memory Card Listing
button or [F1] to scroll through the file names. This button does not
display the names of font files (*.OTF).
Disconnect Card [F8] or [F5]
Closes all files on the memory card. Press Disconnect before
removing the card from the slot to ensure all files are closed. A
message appears when you can remove the card from the card slot.
Failure to follow this procedure could damage the card.
Applications on Card
Displays the selected application file stored on the memory card.
Restore From Card [F2]
Transfers the application under Applications on Card to the terminal.
Any application in the terminal is overwritten.
Save to Card [F3]
Saves the current application in the terminal to the memory card.
Erase/Format Card [F4]
Erases and formats a 2711-NM11, -12, -13, -14 memory card. This
function deletes all applications on the card. You can’t delete
individual files. Don’t perform this operation on a 2711-NM22, -24,
-26 ATA card or the card will be inoperable.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-6
Configuring the Terminal
Configuring Communications
Select Communication Setup from the Configuration Mode menu to
display or change the communication settings for your PanelView
terminal. The screen that appears depends on the communication
protocol of the terminal.
DH-485 Communications
The DH-485 screen lets you modify or display DH-485 settings for
either a DH-485 or RS-232 PanelView terminal. Default settings are:
•
Max Node Address = 31
•
Node Address = 2
•
Baud Rate = 19200
!
ATTENTION: Settings downloaded with a DH-485
application take priority over terminal settings and take
effect immediately after the download.
DH-485
Max Node:
31
F1
Node:
2
F2
19200
Baud:
Comm
LED
Fault
LED
F3
EXIT
F16
Max Node [F1]
Opens the numeric entry scratchpad. Enter the highest node number
on the network (up to 31) and press the Enter ↵ key. (On touch screen
terminals, press the ↵ key on the scratchpad). A change to the
maximum node address takes effect immediately.
Node [F2]
Opens the numeric entry scratchpad. Enter the node address of the
terminal (0 - 31) and press the Enter ↵ key. (On touch screen
terminals, press the ↵ key on the scratchpad). If you enter a value
greater than the maximum node address, the value is accepted and the
maximum node address is updated. A node address change takes
effect immediately.
Baud [F3]
Steps through the baud rates with each key press: 1200, 2400, 9600,
19200. The selected baud rate takes effect immediately.
Publication 2711-6.1
Configuring the Terminal
3-7
Comm LED
Pattern
Indicates
Solid Fill
Normal operating state
Blinking
No communications established
Fault LED
Pattern
Indicates
No Fill
Normal operating state
Blinking
Hardware is functioning but no application file is
loaded or the current application is corrupted.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-8
Configuring the Terminal
DH+ Communications
The DH+ screen lets you display or modify communication settings
for the DH+ version of the PanelView terminals.
ATTENTION: Settings downloaded with a DH+
application take priority over terminal settings and take
effect immediately after the download.
!
DH+
Node:
2
F1
Baud:
57.6 K
F2
Comm
LED
Fault
LED
EXIT
F16
Node [F1]
Opens the numeric entry scratchpad. Enter the node address (0 - 77
octal) of the terminal on the DH+ link and press the Enter ↵ key. (On
touch screen terminals, press the Enter key on the scratchpad). A
node change takes effect immediately.
Baud [F2]
Steps through the baud rates with each key press: 57.6K (default),
115.2K, 230.4K. The selected rate takes effect immediately. The
maximum cable length is restricted at higher baud rates.
Comm LED
•
solid fill - normal operating state
•
blinking - no communications established
•
no fill - hardware failure
Fault LED
•
no fill - normal operating state
•
blinking - hardware is functioning but an application is not loaded
or the current application is corrupted.
•
solid fill - hardware failure
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
3-9
Remote I/O Communications
The RIO Configuration screen lets you display communication
settings for a Remote I/O terminal. Remote I/O settings are
configured with the out-of-box application provided with the terminal
or from the PanelBuilder software.
RIO Configuration
Rack Number:
3
Rack Size:
Full
Starting Group:
0,1
Pass-Through Enabled:
Yes
Last Chassis:
Yes
115.2K
Baud:
No PLC Communication
F3
EXIT
F16
Settings are read only, except for baud rate.
Rack Number (read only)
Displays the current rack number (0 to 76 octal) of the terminal.
Rack Size (read only)
Displays the current rack size (1/4, 1/2, 3/4 or Full) of the terminal.
Starting Group (read only)
Displays the starting module group of the terminal: 0,1 2,3 4,5 6,7
Pass-Through Enabled (read only)
Enables/disables Pass-Through which allows you to transfer
applications between a computer on the Allen-Bradley DH+ network
and a terminal on the Remote I/O link. A PLC-5 controller passes
data between the two networks.
Last Chassis (ready only)
Indicates whether the terminal occupies the last module group in its
assigned rack.
Baud [F3]
Steps through the baud rates with each key press: 57.6K (default),
115.2K, 230.4K. The selected rate takes effect immediately. The
maximum cable length is restricted at higher baud rates.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-10
Configuring the Terminal
ControlNet Communications
The ControlNet screen lets you display communications settings for a
ControlNet terminal. You are only allowed to change the Node
Address and Interscan Delay settings.
ATTENTION: Settings downloaded with a
ControlNet application take priority over terminal
settings and take effect immediately after the download.
!
ControlNet
New Node Address F2:
##
Active Node Address:
03
Interscan Delay F3:
100
FW Revision: ########
Channel
Status
Comms
Status
Restart
Terminal
F1
ms
Serial #: ########
Channel B
Connected
EXIT
F16
New Node Address [F2]
Opens the numeric entry scratchpad. Enter the node address (01 - 99
decimal) of the terminal and press the Enter ↵ key. On touch screen
terminals, press the ↵ key on the scratchpad. The initial default is 3.
The change takes effect after the terminal is reset. If you enter a value
greater than the UMAX node address, the terminal will not go online
with the network.
Active Node Address (read only)
Displays the current address of the PanelView terminal.
Interscan Delay [F3]
Opens the numeric entry scratchpad so you can change the Interscan
Delay. Enter the delay (100 to 1000 milliseconds in multiples of 100)
and press the Enter key. On touch screen terminals, press the ↵ key
on the scratchpad. The initial default is 100. A change takes effect
immediately.
FW Revision (read only)
Shows the revision # of the firmware in the ControlNet terminal.
Serial Number (read only)
Displays a unique, 32-bit serial number for the PanelView terminal.
Comms Status
Displays the current status of the communication card. Connected
appears when the PanelView is connected to the network and
operating properly.
Publication 2711-6.1
Configuring the Terminal
3-11
Channel Status
Displays a value indicating the current status of channel A and B. The
definition of each status condition follows the table. If multiple status
conditions apply, the highest priority condition is displayed.
Displayed
Value
Status
A
B
Displayed
Value
Status
A
B
Displayed
Value
Status
A
B
Displayed
Value
Status
A
B
119
7
7
87
7
5
55
7
3
23
7
1
118
6
7
86
6
5
54
6
3
22
6
1
117
5
7
85
5
5
53
5
3
21
5
1
116
4
7
84
4
5
52
4
3
20
4
1
115
3
7
83
3
5
51
3
3
19
3
1
114
2
7
82
2
5
50
2
3
18
2
1
113
1
7
81
1
5
49
1
3
17
1
1
112
0
7
80
0
5
48
0
3
16
0
1
103
7
6
71
7
4
39
7
2
7
7
0
102
6
6
70
6
4
38
6
2
6
6
0
101
5
6
69
5
4
37
5
2
5
5
0
100
4
6
68
4
4
36
4
2
4
4
0
99
3
6
67
3
4
35
3
2
3
3
0
98
2
6
66
2
4
34
2
2
2
2
0
97
1
6
65
1
4
33
1
2
1
1
0
96
0
6
64
0
4
32
0
2
0
0
0
Status
Indicates
Priority
7
Terminal failure. Contact Allen-Bradley for technical
support.
1 (Highest)
6
Self test being performed. Wait for end of test.
2
5
Incorrect node configuration. Check for duplicate
nodes.
3
Incorrect network configuration (such as overflow/
underflow if signaled by host, out-of-step). Check for a
node greater than UMAX.
4
Cable fault or lonely connection (such as disconnected
cable, redundancy warning).
5
2
Temporary network errors (such as bad MAC frame,
screeners not programmed).
6
1
Channel ok.
7
0
Channel disabled.
8 (Lowest)
4
3
Restart Terminal [F1]
Resets the PanelView terminal. A new node address takes affect after
a reset.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-12
Configuring the Terminal
DeviceNet Communications
The DeviceNet screen lets you display or modify communication
settings for a DeviceNet terminal.
ATTENTION: Settings downloaded with a
DeviceNet application take priority over terminal
settings and take effect immediately after the download.
!
DeviceNet
New Node Address F2:
Active Node Address:
New Baud F3:
Active Baud:
2
Input Size:
0
Output Size:
0
125K
125K
Bus-off Interrupt F4:
Hold in Reset
Interscan Delay F5:
500
Comms Firmware Revision:
Restart
Terminal
F1
ms
Serial Number:
Mod/Net LED:
Not Connected
EXIT
F16
Restart Terminal [F1]
Resets the terminal.
New Node Address [F2]
Opens the numeric entry scratchpad. Enter the node address (0 - 63)
of the PanelView terminal on the DeviceNet link and press the Enter
↵ key. On touch screen terminals, press the ↵ key on the scratchpad.
A node change takes effect on reset.
Active Node Address (read only)
Displays the current network operating address of the PanelView
terminal.
New Baud [F3]
Step through the baud rates with each key press: 125K (default),
250K, 500K. The selected takes effect immediately. The maximum
cable length is restricted at higher baud rates.
Active Baud (read only)
Displays the current baud rate of the PanelView terminal. The baud
rate is set to the New Baud value at power-up.
The active baud is the rate of the PanelView, not the network. The
PanelView is not automatically set to the network baud rate.
Publication 2711-6.1
Configuring the Terminal
3-13
Bus-off Interrupt [F4]
Specifies what occurs when a CAN bus-off interrupt occurs on the
DeviceNet network. The PanelView is not allowed network access
when Hold on Reset is selected and a Bus-off Interrupt occurs.
•
Hold in Reset holds the PanelView and waits for a
communications reset or a terminal reset.
•
Reset and Continue Communications resets DeviceNet
communications and re-establishes the communications link.
Interscan Delay [F5]
Opens the numeric entry scratchpad so you can change the delay
between scans of the Explicit-Client tags. Enter a value of 0 to 65535
milliseconds and press the Enter ↵ key. (On touch screen terminals,
press the ↵ key on the scratchpad.) The default is 500 milliseconds.
This time delay is inserted between each full scan of the ExplicitClient tags in the current screen context. The value is initially set by
the downloaded application but can be changed by an operator. When
changed, the new value takes effect immediately.
Explicit-Client mode will generate low priority, network messaging
at intervals less than 500 milliseconds.
Input Size
Displays the number of words (0 to 64) sent by the PanelView in an I/
O message. The default value is 0, which indicates that no output data
is exchanged with the scanner. This value is set by the downloaded
application.
Output Size
Displays the number of words (0 to 64) received by the PanelView in
an I/O message. The default value is 0, which indicates no output data
is exchanged with the scanner. This value is set by the downloaded
application.
Comm LED
•
solid fill - normal operating state
•
blinking - no communications established
•
no fill - hardware failure
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-14
Configuring the Terminal
DF1 Communications
The DF1 screen lets you display or modify DF1/full duplex
communication settings for a DF1 PanelView terminal.
ATTENTION: Settings downloaded with a DF1
application have priority over terminal settings and take
effect immediately after the download.
!
DF1 - Full Duplex
Communication
Parameters
F1
F2
No Parity
8 Data Bits
1 Stop Bit
9600
F3
Fault
LED
64
CRC
Handshaking
Node
F4
Comm
LED
Error
Detection
Baud Rate
F5
OFF
Connected
EXIT
F16
Communication Parameters [F1]
Sets the communication parameters for the DF1 port on the
PanelView terminal. The settings must match the target device. Each
key press toggles through the available combinations for:
•
Parity = None (default), Even or Odd
•
Data Bits = 8
•
Stop Bits = 1 (default) or 2
The DF1 port on the PLC-5 controllers allows a parity of Even or
None parity with 8 Data Bits. For the SLC controllers, the parity is
fixed at None and uses CRC error detection.
Baud Rate [F2]
Steps through the baud rates for the DF1 communications port with
each key press: 1200, 2400, 4800, 9600, 19200. The initial default is
9600.The baud rate must match the baud rate of the target device.
Error Detection [F3]
Specifies the type of error checking performed on data. The default is
CRC (Cyclic Redundancy Check).
Publication 2711-6.1
•
BCC (Block Check Character) - modulo-256 arithmetic sum of
an array of data bytes used for medium-level data verification.
•
CRC (Cyclic Redundancy Code) - calculated on an array of data
bytes and used for high-level data verification.
Configuring the Terminal
3-15
Node [F4]
Specifies the node number (0 - 254 decimal) for DF1 network
communications. For point-to-point communications with an SLC,
PLC, MicroLogix or a 1761-NET DNI module, the default node
number of 64 is used.
When you press F4, the numeric entry scratchpad opens. Enter a node
number and press the Enter ↵ key. (On touch screen terminals, press
the ↵ key on the scratchpad.)
Handshaking [F5]
Specifies the type of handshaking used by the RS-232 port.
•
On (CTS/RTS enabled)
•
OFF (CTS/RTS disabled)
Press F5 or touch the box to select an option. The default is Off.
Comm LED
•
solid fill - normal operating state
•
blinking - no communications established with logic controller
•
no fill - hardware failure
Fault LED
•
no fill - normal operating state
•
blinking - hardware is functioning but an application is not loaded
or the current application is corrupted.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-16
Configuring the Terminal
Configuring Presets
Select Preset Operations from the Configuration Mode menu to set
the values of control objects after a reset or power cycle. You can set
presets to:
•
values provided by the PanelView application or
•
last values entered from terminal prior to a reset or power down.
PRESET OPERATIONS
Power Up With:
Presets
Last States
F1
Restart Unit
And
Load Values
Key Repeat
Rate
F7
F15
1000 ms
Key Repeat
Delay
200 ms
EXIT
F16
Power-Up with Presets or Last States
Displays the current power-up selection. Use the up and down arrow keys on keypad terminals (or the up and down keys on touch
screen terminals) to select an option. The selection takes effect the
next time the terminal is powered on.
•
Select Presets to load initial values of control objects (into PLC/
SLC data tables) with values supplied by application.
•
Select Last States to load initial values of control objects (into
PLC/SLC data tables) with values entered at the terminal prior to
a terminal reset or power down.
Restart Unit and Load Values [F1]
Loads the values selected in the Power-Up With list and resets the
terminal.
Key Repeat Rate [F4] or [F7]
Specifies the number of repeats that occur per second when a key is
pressed and held. Steps through key repeat rates: 0 (disabled), 200ms
(5 times/sec), 250ms (4 times/sec), 330ms (3 times/sec), 500ms (2
times/sec), 1000ms (1 time/sec).
Key Repeat Delay [F9] or [F15]
Specifies how long a key must be pressed before it is repeated. Steps
through delay rates: 200ms, 400ms, 600ms, 800ms, 1000ms, 1500ms,
2000ms, 2500ms.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
Viewing Terminal Information
3-17
Select Terminal Info from the Configuration Mode menu to display
information about your terminal. This information may be needed
when calling for technical support.
TERMINAL INFO
Boot:
############
Firmware:
############
Hardware:
#######################################
Filename:
############
Fontfile:
############
############
Bytes Used
############
Bytes Free
EXIT
F16
Boot
Displays the boot code revision.
Firmware
Displays the firmware revision.
Hardware
Displays the hardware configuration.
Keypad (CPS)
Touch Screen (TS)
Keypad and Touch Screen (TS CPS)
Communications Port (P0.485,P0.232,P1.RIO,P1.DH+,P1.232,P1.DF1)
Screen Size (SS5.5, SS6.0, SS9.0, SS10.0, SS14.0)
Filename
Displays the name of the active application file. If the application file
exists but is invalid, the file name appears as ********.
•
Bytes Used displays the number of bytes used by the loaded
application.
•
Bytes Free displays the number of bytes available.
Font File
Displays the name of the external font file used by the application.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-18
Configuring the Terminal
Adjusting Screen Parameters
Select Screen Setup from the Configuration Mode menu to adjust
settings of the terminal display. Changes take effect immediately.
PanelView 550 Screen Setup
SCREEN SETUP
Contrast
Backlight
F2
F7
Off
F3
Backlight
Timeout
10 min.
F9
10
Reset
Video
Video Mode
F4
Reverse
EXIT
F10
Note: Certain settings may make viewing the screen difficult. Do not
exit this screen until viewing adjustments are acceptable.
Backlight [F2]
Turns the backlight On, Off or to Timed mode. When set to Timed,
the Backlight Timeout value determines when the backlight is turned
off.
Contrast [F3]
Increases or decreases the display contrast. The contrast settings
range from 0 to 10.
Video Mode [F4]
Toggles between normal video (dark text/graphics on a light
background) and reverse video (light text/graphics on a dark
background). Changes take effect immediately.
Backlight Timeout [F7]
Specifies when the backlight turns off if user input or a controller
screen change is not received. The timeout settings are 5, 10, 20, 25,
or 30 minutes. The Backlight Timeout value is used when the
Backlight parameter is set to Timed.
Reset Video [F9]
Resets the display to normal (default settings). The [F9] key is also
active on the Configuration Mode menu. If the screen is set to a nonviewable setting, press the Left and Right arrow keys
simultaneously. Then press [F9] to reset the screen.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
3-19
PanelView 600/900/1000 Color - Screen Setup
SCREEN SETUP
Screen
Saver
Normal
Intensity
Off
100
F1
F2
Reset
Video
F15
SCREEN SAVER
Timeout
Intensity
10 min.
F9
0
F10
EXIT
F16
Note: Certain settings may make viewing the screen difficult. Do not
exit this screen until viewing adjustments are acceptable.
Normal Intensity [F2]
Adjusts the intensity of the display with each key press. PV600/1000
settings are 10 - 100, in 10 step increments. PV900 settings are 50 100, in 10 step increments.
Screen Saver Mode [F1]
Sets the screen saver to Timed or Off. When Timed, the screen
intensity is reduced if user input or a controller screen change is not
received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F6] or [F9]
Specifies when an inactive screen enters screen saver mode. The
timeout is adjusted in steps with each key press: 5, 10, 15, 20, 25, or
30 minutes.
Screen Saver Intensity [F7] or [F10]
Adjusts the intensity of the display during screen saver mode. PV600/
1000 settings are 0 - 100, in 10 step increments. PV900 settings are 0,
and 50 - 100, in 10 step increments. It is recommended that you set
the intensity to a value less than 100 to prolong the life of the
backlight.
Reset Video [F9] or [F15]
Resets the display to normal video (default settings). The [F9] and
[F15] keys are active on the Configuration Mode menu. If the screen
is non-viewable, press the left and right arrow keys
simultaneously. Then press [F9] or [F15] to reset the screen.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-20
Configuring the Terminal
PanelView 900 Monochrome - Screen Setup
SCREEN SETUP
SCREEN SAVER
Normal Intensity
80
Mode
Timed
F1
F3
Video Mode
Normal
Timeout
10 min.
F2
F4
Reset
Video
Intensity
80
F15
F5
SCREEN CONDITIONER
Mode
Disabled
F6
Hour Minute
## :
0#
F8
F7
EXIT
F16
Note: Certain settings may make viewing the screen difficult. Do not
exit this screen until viewing adjustments are acceptable.
Normal Intensity [F1]
Adjusts the intensity of the display with each key press: 35, 40, 50,
60, 70, 80, 90, 100. A new setting takes effect immediately.
Video Mode [F2]
Toggles between normal video (light text/graphics on a dark
background) and reverse video (dark text/graphics on a light
background). The change takes effect immediately. Normal video is
recommended.
Screen Saver Mode [F3]
Sets the screen saver to Timed or Off. When Timed, the screen
intensity is reduced if user input or a controller screen change is not
received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F4]
Specifies when an inactive screen enters screen saver mode. The
timeout is adjusted in steps with each key press: 5, 10, 15, 20, 25 or
30 minutes.
Screen Saver Intensity [F5]
Adjusts the intensity of the display during screen saver mode. The
intensity is adjusted with each key press: 0, 35, 40, 50, 60, 70, 80, 90,
100
Publication 2711-6.1
Configuring the Terminal
3-21
Screen Conditioner Mode [F6]
Enables or disables the screen conditioner. This parameter sets a daily
schedule for conditioning the display of a PV900 monochrome
terminal to prevent image burn-in.
The conditioning process takes approximately 30 minutes and will
not start until the terminal is inactive and in screen saver mode. You
can interrupt the screen saver or conditioner at any time by pressing a
key or the touch screen. If the screen conditioner is interrupted, it will
resume when the screen saver is reactivated.
If you do not use the conditioner, random pixels will illuminate
around objects after a period of time (approximately one year).
Screen Conditioner Hour [F7]
Specifies the hour at which to start the screen conditioner. The
numeric entry scratchpad opens. Enter a value between 0 - 23, then
press the Enter ↵ key (on touch screen terminals, press the Enter key
on the scratchpad).
Screen Conditioner Minute [F8]
Specifies the minute at which to start the screen conditioner. The
numeric entry scratchpad opens. Enter a value between 0-59, then
press the Enter ↵ key (on touch screen terminals, press the Enter key
on the scratchpad).
Reset Video [F15]
Resets the display to normal video (default settings).
On keypad terminals, the [F15] key is also active on the
Configuration Mode menu. If the screen is non-viewable, press the
Left and Right arrow keys simultaneously. Then press [F15] to
reset the screen.
Exit [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-22
Configuring the Terminal
PanelView 1000 Grayscale -Screen Setup
SCREEN SETUP
Screen
Saver
Video
Mode
Off
Normal
Reset
Video
F1
F2
F15
SCREEN SAVER
Timeout
Intensity
10 min.
0
F9
F10
EXIT
F16
Note: Certain settings may make viewing the screen difficult. Do not
exit this screen until viewing adjustments are acceptable.
Video Mode [F2]
Toggles between normal video (darker text/graphics on a light
background) and reverse video (lighter text/graphics on a dark
background). The change takes effect immediately. Normal video is
recommended.
Screen Saver Mode [F1]
Sets the screen saver to Timed or Off. When Timed, the screen
intensity is reduced if user input or a controller screen change is not
received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F9]
Specifies when an inactive screen enters screen saver mode. The
timeout is adjusted in 5 minute increments with each key press, from
5 to 30 minutes.
Screen Saver Intensity [F10]
Adjusts the intensity of the display during screen saver mode.
Settings are 0 (lowest intensity) or 100 (highest intensity). 0 is
recommended to prolong the display life.
Reset Video [F15]
Resets the display to normal video (default settings).
On keypad terminals, the [F15] key is also active on the
Configuration Mode menu. If the screen is non-viewable, press the
Left and Right arrow keys simultaneously. Then press [F15] to
reset the screen.
Exit [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
3-23
PanelView 1400 Color Setup
SCREEN SETUP
SCREEN
SAVER
Mode
Off
F1
Timeout
5 min.
F2
Intensity
100
F3
DEGAUSS
Auto
Normal
Intensity
Enabled
100
F8
F4
Hour Minute
## : 0#
F5
F6
Manual
Degauss
F7
Reset
Video
F15
ALIGN
TOUCH
GRID
Touch Screen only
EXIT
F16
Note: Certain settings may make viewing the screen difficult. Do not
exit this screen until viewing adjustments are acceptable.
Screen Saver Mode [F1]
Sets the screen saver to Timed or Off. When Timed, the screen
intensity is reduced if user input or a controller screen change is not
received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F2]
Specifies when an inactive screen enters screen saver mode. The
timeout is adjusted in 5 minute increments with each key press, from
5 to 30 minutes.
Screen Saver Intensity [F3]
Adjusts the intensity of the display during screen saver mode. The
intensity is adjusted with each key press: 0, 25, 50, 75, 100.
Degauss Auto [F4]
Enables or disables automatic degaussing. The degauss process takes
a few seconds and will not start until the terminal is inactive.
Automatic degaussing occurs at midnight unless you adjust the hour
and time parameters.
Degauss Hour [F5]
Specifies the hour to start automatic degaussing. The numeric entry
scratchpad opens. Enter a value between 0 - 23, then press the Enter ↵
key (on touch screen terminals, press the Enter key on the
scratchpad).
Degauss Minute [F6]
Specifies the minute to start automatic degaussing. The numeric entry
scratchpad opens. Enter a value between 0 - 59, then press the Enter ↵
key (on touch screen terminals, press the Enter key on the
scratchpad).
Manual Degauss [F7]
Allows you to manually degauss the display. When you press [F7],
the display is degaussed immediately.
Publication 2711-6.1
3-24
Configuring the Terminal
Normal Intensity [F8]
Adjusts the intensity of the display with each key press: 25, 50, 75,
100. The new setting takes effect immediately.
Reset Video [F15]
Resets the display to normal video (default settings).
On keypad terminals, the [F15] key is also active on the
Configuration Mode menu. If the screen is non-viewable, press the
Left and Right arrow keys simultaneously. Then press [F15] to
reset the screen.
Align Touch Grid - PV1400 Touch Screen only
Opens the touch alignment screen, which lets you realign the screen
with the touch grid. This function is useful when the terminal is
positioned at an angle and viewing the screen is difficult unless you
realign the screen.
EXIT
F16
Move the screen until it aligns with the touch cells. Alignment
changes are permanent.
Press:
To:
Move the screen up one pixel.
Move the screen down one pixel.
Move the screen to the right 2 pixels.
Move the screen to the left 2 pixels.
Move the screen to its factory default position.
Exit
Exit the touch alignment screen and return to Screen Setup.
Exit [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
Setting the Time and Date
3-25
Select Date/Time from the Configuration Mode menu to reset the
data and/or time.
DATE/TIME
Year
####
Month
####
Day
####
F1
F2
F3
Minute
####
Second
####
Hour
####
F9
F11
F10
MMM/DD/YYYY
EXIT
F16
MHH:MM:SS PM
Setting the Time
Use screen buttons (touch screens) or function keys to set the time.
On PV50/PV600 Press:
On PV900/1000/1400 Press:
To:
Hours button [F6] key
Hour button [F9] key
Set current hour
Minute button [F7]
Minute button [F10]
Set minutes
Second button [F8]
Second button [F11]
Set seconds
The scratchpad opens to enter each setting. Use the terminal keypad
to enter the values. Press ↵ after each entry. Changes take effect
immediately.
Setting the Date
Use screen buttons (touch screens) or function keys to set the date.
Press:
To:
Year button [F1] key
Set current year
Month button [F2]
Set month (1 to 12)
Day button [F3]
Set day (1 to 31)
The scratchpad opens to enter each setting. Use the terminal keypad
to enter the values. Press ↵ after each entry. Changes take effect
immediately.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-26
Configuring the Terminal
Setting up the Printer
Select Printer Setup from the Configuration Mode menu to set
parameters for those terminals equipped with an RS-232 printer port.
Any printer that supports the IBM enhanced character set can be
connected to the RS-232 printer port.
PRINTER SETUP
Handshaking
Communication Parameters
Baud Rate
XON/XOFF
No Parity
8 Data Bits
1 Stop Bit
19200
F2
F1
F3
Port Mode
Top Of
Form
F9
Printing
Enabled
EXIT
F16
F10
Printer settings are maintained between power cycles.
Page format parameters for printing are defined in the Terminal Setup
dialog and downloaded with the application.
Handshaking [F1]
Specifies the type of handshaking used by the RS-232 port.
•
None (initial default)
•
Hardware
•
XON/XOFF
Communication Parameters [F2]
Sets the communication parameters for the printer port. Each key
press toggles through the available combinations for:
•
Parity (None, Even or Odd)
•
Data Bits (7 or 8)
•
Stop Bits (1 or 2)
Baud Rate [F3]
Sets the baud rate of the printer port. The baud rate must match the
baud rate of the printer. The baud rate is adjusted with each key press:
1200, 2400, 4800, 9600, 19200. The initial default is 9600.
Publication 2711-6.1
Configuring the Terminal
3-27
Top of Form [F6] or [F9]
Notifies the PanelView terminal the printer is at the top of a page.
Manually adjust the printer to the top of the page before pressing the
Top of Form button. The printer also uses the Perforation Skip Value
(if defined in the Printer Setup of the PanelBuilder software) when
the Top of Form button is pressed.
On powerup, the terminal assumes the printer is at the top of a page.
Port Mode [F7] or [F10]
Enables or disables printing for the RS-232 port.
The RS-232 port on some terminals supports both printing and
application transfers. If you disable printing, the port is used for
application transfers.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-28
Configuring the Terminal
Publication 2711-6.1
Chapter
4
Using a Memory Card
Chapter Objectives
Supported Memory Cards
This chapter describes:
•
supported memory cards
•
using the memory card retainer
•
loading application from a memory card
•
loading application on a memory card
•
storing font files on a memory card
•
removing a memory card
Memory cards are available to transfer application files to/from a
PanelView terminal.
PanelView terminals running firmware 3.0 (or later) and computers
with an ATA card drive support the following cards:
•
2M flash ATA card (Catalog No. 2711-NM22)
•
4M flash ATA card (Catalog No. 2711-NM24)
•
6M flash ATA card (Catalog No. 2711-NM26)
All PanelView terminals and computers with a DataBook TMB240 or
TMB250 card drive support these cards:
•
256K flash memory card (Catalog No. 2711-NM11)
•
1M flash memory card (Catalog No. 2711-NM12)
•
2M flash memory card (Catalog No. 2711-NM13)
•
4M flash memory card (Catalog No. 2711-NM14)
Publication 2711-6.1
4-2
Using a Memory Card
Using the Memory Card Retainer
A Memory Card Retainer (Catalog No. 2711-NMCC or -NMCD) is
shipped with all PanelView terminals, except the PV1400. It is
required for:
•
UL508 installations
•
vibration/mechanical shock environments
•
CE certified installations
•
installations where the application uses a font file on a memory
card, and the card must remain in the terminal during operation.
The following illustration shows the memory card and the memory
card retainer. The card loads in the back of the terminal with the key
slot on top.
Key Slot
Memory Card Retainer
Connector Slots
Memory Card Slot
A-B logo on right side
Note: The back of the PanelView 900 terminal is shown above. The
location of the card slot will vary between the different terminals.
Publication 2711-6.1
Using a Memory Card
4-3
The Memory Card Retainer protects against:
•
electrical shock from loose high voltage wires in an electrical
enclosure per UL508
!
•
electrostatic discharge (ESD) up to 15KV
!
•
ATTENTION: When permanently installing a
memory card in an electrical enclosure, the memory
card retainer must be used to avoid accidental contact
of high voltage leads to metal surfaces on the card.
Failure to use the retainer could result in physical injury
or damage to the terminal.
ATTENTION: Without the memory card retainer
installed, electrostatic discharge could reset or damage
the PanelView terminal.
accidental removal or ejection of the memory card from the card
slot.
!
ATTENTION: Accidental removal of an ATA flash
card from the card slot could result in damage to the
card.
Publication 2711-6.1
4-4
Using a Memory Card
Loading Application
from a Memory Card
The procedure below shows how to load an application on a memory
card into the PanelView terminal.
!
ATTENTION: Explosion Hazard - Do not install or
remove memory card unless power has been switched
off or the area is known to be non-hazardous.
To load an application from a memory card:
1. Insert the memory card in the card slot of the terminal.
If the terminal does not have an application loaded, the
Configuration Mode menu appears. Skip step 2.
2. Open the Configuration Mode menu by simultaneously pressing
the Left and Right arrows (on keypad terminals), or the Goto
Config. Screen button (on touch screen terminals.
Function keys do not
appear on touch
screen terminals.
3. Select Memory Card and press the Enter ↵ key.
4. Press Memory Card Listing, [F1] on keypad terminals, until the
application file you want to load is displayed.
Publication 2711-6.1
Using a Memory Card
4-5
5. Press Restore From Card, [F2] on keypad terminals, to begin the
transfer.
Because this operation overwrites the current application in the
terminal, you are prompted to abort or continue.
Proceed with download?
F1 - Abort
F2 - Continue
The terminal displays the status of the transfer.
In progress . . .
6. When the transfer is complete, the PanelView terminal checks the
validity of the application, resets and runs the application.
Publication 2711-6.1
4-6
Using a Memory Card
Loading Application
on a Memory Card
The steps below shows how to load an application in the terminal
onto a memory card.
!
ATTENTION: Explosion Hazard - Do not install or
remove memory card unless power has been switched
off or the area is known to be non-hazardous.
To transfer an application to a memory card:
1. Insert the memory card into the card slot of the terminal.
2. Open the Configuration Mode menu by simultaneously pressing
the Left and Right arrows (on keypad terminals), or the Goto
Config. Screen button (on touch screen terminals.
Function keys do not
appear on touch
screen terminals.
3. Select Memory Card and press the Enter ↵ key.
4. If necessary, press Erase/Format Card, [F4] key on keypad terminals, to format or erase a 2711-NM11, -12, -13, -14 memory card.
Do not perform this operation on a 2711-NM22, -24, -26 ATA
card. The card becomes inoperable.
Because this operation erases all data on the memory card, you
are prompted to abort or continue.
Format erases entire card?
F1 - Abort
F2 - Continue
Publication 2711-6.1
Using a Memory Card
4-7
5. Press Save to Card, [F3] on keypad terminals, to transfer the
application in the terminal to the card.
If the application already exists on the memory card, you are
prompted to abort or continue.
The .PVA file exits:
F1 - Abort
F2 - Upload with new PVA file
The terminal displays the status of the transfer.
In progress . . .
6. When the transfer is complete, the application file name appears
in the Applications on Card list. Press Memory Card Listing, [F1]
key on keypad terminals, to scroll through the list.
Note: If you upload a file that exists on the memory card, the
uploaded file name is altered with a sequential digit as a suffix.
For example, Control.pva becomes Control0.pva.
For files with eight character names, a digit overwrites the last
character. For example, Motorcon.pva becomes Motorco0.pva.
Publication 2711-6.1
4-8
Using a Memory Card
Storing Font Files
on a Memory Card
Memory cards also store font files for languages used by PanelView
applications. The font file contains the character set for the language.
The memory card containing the font file must be inserted in the
PanelView terminal while the application is running. The terminal
uses the font file to display characters on the application screen.
To view the name of the font file used by an application, select
Terminal Info from the Configuration Mode menu.
Because the memory card must remain in the terminal while the
application is running, it is recommended that you use the Memory
Card Retainer (Cat. No. 2711-NMCC, -NMCD) to secure the card in
the card slot. The retainer ensures the card is not accidentally
removed or dislodged during terminal operation.
Removing a Memory Card
Follow the procedure below to remove a memory card from the
PanelView terminal. Failure to follow this procedure may result in
damage to the card.
1. Select Memory Card from the Configuration Mode menu.
2. Press the Disconnect Card button. This ensures that all files are
closed on the card.
A message prompts you to remove the card from the slot. You
can continue or abort the operation.
3. Press the Continue button.
4. Remove the memory card from the card slot.
On PV1400 terminals, press the Memory Card Eject button.
Publication 2711-6.1
Chapter
5
Running Applications
Chapter Objectives
Application Information
This chapter describes operating procedures common to most
applications:
•
push button operation
•
control lists
•
numeric entry controls
•
screen selectors
•
list indicators
•
multistate indicators
•
bar graphs
•
numeric data displays
•
message displays
•
time or date
•
printing
•
alarms
The application designer is responsible for documenting the operation
of an application. Before running the application, you should
understand what processes are being controlled and monitored.
!
ATTENTION: Do not press multiple touch screen
objects at the same time. Pressing multiple objects
simultaneously may result unintended operation.
Publication 2711-6.1
5-2
Running Applications
Push Button Operation
Screen push buttons function like mechanical push buttons.
Push Button
ON
OFF
Push buttons have a variety of appearances. Push buttons may change
their inner text, fill pattern, border or shape when pressed (each state
assigned different attributes).
OFF
Toggle Foreground/
Background
ON
Border, White Fill
SLOW
No Border,
Diagonal Fill
STOP
Ellipse, White Fill
The following are common to most push buttons:
Publication 2711-6.1
•
All push buttons are momentarily disabled (0.5 second) after a
screen change. This prevents multiple buttons, in the same
location on different screens, from being pressed inadvertently.
•
All push buttons must be released on the previous screen before
buttons can be pressed on the new screen.
•
Momentary push buttons are assigned a hold time. The hold time
maintains the pressed state so that each change of state can be
read by the controller at least once. The hold time varies between
0 and 1 second depending on the configured setting.
Running Applications
Control Lists
5-3
Control lists perform functions similar to push buttons. They can
modify either individual bits or values at a controller address.
Cursor indicates selected item
Active selection
is highlighted
Vertical bar indicates active control list
Active List Item
Active item is highlighted.
Active Control List
Has a vertical indicator bar on the left side of the list. Only one
control list or numeric entry cursor point can be active on a screen.
To activate a control list:
•
touch the object (touch screen terminals only)
•
or press the assigned function key
•
or on a screen with multiple control lists or numeric entry cursor
points, press the Left or Right arrows to move the indicator
bar between the objects.
Tank Level Control
Hopper Control
Empty Tank
Open Hopper 1
1/4 Fill Level
Open Hopper 2
1/2 Fill Level
Open Hopper 2
Full Tank
Close Hopper 2
MovesMove
Moves the vertical bar
Publication 2711-6.1
5-4
Running Applications
Cursor
Indicates the selected item. Move the cursor up or down the control
list using the Up and Down arrow keys. Cursor operation is
configured by the application designer. If the cursor is at the first or
last item in a control list pressing the Up arrow (when at the top) or
the Down arrow (when at the bottom) will either:
•
cause no movement of the cursor, or
•
move the cursor to the top or bottom of the list.
Tank Level Control
Tank Level Control
Empty Tank
1/4 Fill
Fill Level
Level
1/4
1/2 Fill Level
Full Tank
Empty Tank
1/4 Fill
Fill Level
Level
1/4
1/2 Fill Level
Full Tank
MovesMove
If the list contains more items than can appear at one time, the list
scrolls. If the cursor is at the top or bottom of a scrolling list, the list
scrolls one row at a time as the arrow keys are pressed.
List Keys
Touch screen terminals require list keys on the screen to move the
cursor in a control list and select entries. The following table shows
the list keys.
List Key
Type
Description
Move Up
Moves the cursor to the previous item in the
list.
Move Down
Moves the cursor to the next item in the list.
Home
Moves the cursor to the first item in the list.
End
Moves the cursor to the last item in the list.
Page Up
Moves the cursor up one page in a scrolling list.
Page Down
Moves the cursor down one page in a scrolling
list.
Backspace
Returns the cursor to the currently highlighted
selection.
Enter
Confirms a selection and sends the value to the
controller if Write on Enter was configured for
the control list.
Cursor - Piloted Control Lists
Publication 2711-6.1
Running Applications
5-5
On a piloted control list, some items are under controller operation
only. In addition, some items may be designated as inactive. You
cannot select controller items or inactive items. In both cases, the
cursor is hollow when you select the item.
State 1
Active State
State 3
State 4
State 5
Cursor at state 2,
an active state
State 1
State 1
State 2
State2
State 2
State 2
Inactive State
State 3
State 4
Inactive State
State 5
Cursor at inactive state 3,
Cursor changes and highlight
remains in original position
State 3
State 4
State 5
Cursor at active state 4,
Cursor changes back and
highlight moves to selection.
To select an item on a control list:
1. Select the control list by:
• touching the screen object (touch screen terminals only)
• or pressing its function key
• or pressing the Left or Right arrow keys until the control
list has a vertical bar indicating it is active
2. Move the cursor up or down the list using the Up or Down
arrows. If the cursor is hollow, the item cannot be selected.
3. Depending on the application design, you may or may not have to
press ↵ to enter the selection indicated by the cursor.
Publication 2711-6.1
5-6
Running Applications
Numeric Entry Controls
Two types of controls allow a numeric value at a controller address:
Cursor Point and Keypad Enable button.
Cursor Point
Press F1 to Enter New Speed
Current Speed = 100 RPM
Motor 1
45
Active
Cursor Point
Motor 2
100
Numeric Entry Cursor Point
34962
A keypad enable button appears like a standard push button. The data
displayed in the button is the last value sent to the button’s tag
address. When selected, a numeric entry scratchpad opens.
Keypad Enable Button
Enter
Value
367
A keypad enable button appears like a standard push button. The data
displayed in the button is the last value sent to the button’s tag
address. When selected, a numeric entry scratchpad opens.
Scratchpad
Both controls display a numeric entry scratchpad in the center of the
screen. The scratchpad shows the current value entered and the range
of possible values you can enter.
Current value entered in scratchpad
550 Touch Screen only
Terminal Scratchpad
Keypad and Keypad/Touch Screen
Terminal Scratchpad
900/1000/1400Touch Screen
Terminal Scratchpad
During data entry, wait until the number you enter appears in the
scratchpad before entering the next number.
Publication 2711-6.1
Running Applications
5-7
To enter a cursor point:
1. Select the cursor point by:
• touching the object (touch screen terminal only)
• pressing the associated function key
• press the Left or Right arrows until the cursor point shows
a vertical bar
2. Press Enter ↵ or type the first digit of the number you want to
enter.
The scratchpad opens.
3. Enter the value using the terminal keypad and press Enter ↵.
To enter a value using the keypad enable button:
1. Press the keypad enable button.
The scratchpad opens.
2. Enter the value using the terminal keypad and press Enter ↵.
To change an entry on a scratchpad:
1. Press the backspace ← key to delete one character at a time.
2. Enter a new value and press Enter ↵.
To cancel a scratchpad:
1. Press the Backspace ← key to delete one character at a time.
2. When pressing Backspace ← in an empty scratchpad (value = 0),
the scratchpad is removed.
Publication 2711-6.1
5-8
Running Applications
Screen Selectors
The 2 types of screen selector controls are Screen List Selectors and
Screen buttons.
Screen List
Selector
Screen Controls
Monitor
Pump Status
ScS
Valve Status
Vertical bar
indicates active list
Tank Control
Tank
Screen
Goto
Screen Button
Previous
Screen
Return
Screen Button
Goto and Return screen buttons can have a variety of appearances
such as unique inner text, fill pattern, border or shape. Return screen
buttons display the previous screen. Goto screen buttons display the
assigned screen.
Screen lists display a list of application screens. The selected screen is
highlighted.
To activate a screen list:
• touch the object (touch screen only)
•
or press the assigned function key
•
or on a screen with multiple screen lists, press the Left
arrow key until a vertical bar appears.
To select an item on a screen list:
1. Move the cursor up or down the list using the Up
arrow keys.
2. Press Enter ↵ to enter the selection.
The selected screen is displayed.
Publication 2711-6.1
or Right
or Down
Running Applications
5-9
Cursor Operation
Cursor operation is configured by the application designer. If the
cursor is at the first or last item in a screen list, pressing the Up
arrow (when at top) or Down arrow (when at bottom) will either:
•
cause no movement of the cursor, or
•
move the cursor to the top or bottom of the list
Screen Controls
Monitor
Pump Status
Valve Status
Tank Control
Screen Controls
Monitor
Pump Status
Valve Status
Tank Control
MovesMove
If a screen list contains more items than can appear at one time, the
list scrolls. If the cursor is at the top or bottom of a scrolling list, the
list scrolls one row at a time as the Up/Down arrows are pressed.
List Keys
Touch screen terminals require list keys on the screen to move the
cursor in a screen list and select an entry. The following table shows
the list keys.
List Key
Type
Description
Move Up
Moves the cursor to the previous item in the
list.
Move Down
Moves the cursor to the next item in the list.
Home
Moves the cursor to the first item in the list.
End
Moves the cursor to the last item in the list.
Page Up
Moves the cursor up one page in a scrolling list.
Page Down
Moves the cursor down one page in a scrolling
list.
Backspace
Returns the cursor to the currently highlighted
selection.
Enter
Confirms a selection and displays the screen.
Publication 2711-6.1
5-10
Running Applications
List Indicators
List indicators highlight an item from a list depending upon the status
of either a bit or value at a controller address.
List Indicator
Mixer Speed
Off
Low
Medium
High
Current status
is highlighted
Mixer
On
Mixer
Off
An indicator list may have a maximum of 255 entries. The list
automatically scrolls to display the status of an item.
Note: List indicators do not have a cursor
selector lists.
Multistate Indicators
like control or screen
Multistate indicators display the status of either a bit or value at a
controller address.
Multistate indicators can have a variety of appearances. In addition,
multistate indicators may change their inner text, fill pattern, or
graphic with each state (each state assigned different attributes). Each
indicator may have up to 2,000 states.
Temp
High
Temp
Low
Toggle Foreground/
Background
Bar Graph Displays
Border, White Fill
OFF
Normal
Cross Hatch,
No Border
Ellipse, White Fill
Bar graphs provide a graphical representation of a variable value. Bar
graphs can appear with or without scales and border, and can have a
variety of fill patterns.
100
+200
-10
Vertical Bar
Hatched Filll,
No Scale
Publication 2711-6.1
0
Vertical Bar
Solid Fill, with Scale
-200
3 Vertical Bars
Various Fills, with Scale
0
+10
2 Horizontal Bars
Different Fill, with Scale
Running Applications
Numeric Data Displays
5-11
Numeric Data Displays may appear with or without supporting text.
Flow=
37 Gallons
000239.45
Depending on the application design, displayed data may have these
properties:
Message Displays
Time or Date
•
zero fill
•
fixed, floating or no decimal point
•
different field widths (number of digits)
•
various text sizes
•
scaled
Message displays contain alphanumeric characters and are displayed
when triggered by a controller. The message display can be any size
and will not overlap other controls. Messages may contain:
•
alphanumeric text
•
variable data
•
graphics
•
time and date
Time and date information can appear as a separate item or in some
control/display objects (push buttons, multistate indicators, message
displays or data displays). A time and date can appear with or without
supporting text.
The date can have a variety of formats.
Month/Day/Year
7/3/99
With Leading Zeroes
07/03/99
Day/Month/Year
3/7/99
With 4 Digit Year
3/7/99
Year/Month/Day
99/7/3
With User-Defined Separator
7*3*99
The time can also have a variety of formats.
12 Hour Format
2:56
With Time Zone & Time
Standard Designations
07/03/97
24 Hour Format
14:56
With Leading Zeroes
02:56
with Seconds
14:56:29
With User-Defined Separator
14*56*29
Publication 2711-6.1
5-12
Running Applications
Printing
Terminals equipped with an RS-232 printer port can print:
•
triggered messages in a message display
•
triggered states of a multistate indicator
•
alarm messages
•
alarm history
Text is printed without formatting options. Print attributes for objects
and alarms are defined in the application.
Printing is a background operation. While printing, the terminal
continues to update and you can perform other terminal operations.
The terminal prints messages in the order they are received. If the
print buffer is full, the terminal displays a queue full warning
message. New print requests are aborted.
The print queue is not maintained between power cycles. Any
messages in the queue when the terminal is reset are cleared.
Alarms
Applications that support alarms may contain:
•
•
•
Alarm Banner display that pops up when an alarm is triggered
Alarm buttons that enable the operator to act on an alarm (Print
Alarm, Acknowledge Alarm, Clear Alarm, Acknowledge All)
Alarm List which stores information on triggered alarms (Print
Alarm List or Clear Alarm List button)
Alarm configurations are application dependent. Consult your
application designer for details on how to handle alarms for your
application.
Publication 2711-6.1
Chapter
6
Installing the PV550 Terminal
Chapter Objectives
Hazardous Locations
This chapter describes how to mount the PV550 terminal in a panel or
enclosure including:
•
hazardous locations
•
enclosures
•
required tools
•
mounting dimensions
•
clearances
•
cutout dimensions
•
installing the PV550 terminal in a panel
See the nameplate label on terminal for hazardous locations
certifications.
!
ATTENTION: In Class 1, Division 2 Hazardous
locations, the PanelView 550 terminal must be wired
per the National Electric Code as it applies to hazardous
locations. Peripheral equipment must also be suitable
for the location in which it is installed.
The following PV550 terminals have an operating temperature code
of T2 (maximum operating temperature of 300° C or 572° F).
•
keypad terminals (series C or higher)
•
keypad & touch screen terminals (series C or higher)
•
all touch screen only terminals
Do not install these terminals in environments where atmospheric
gases have ignition temperatures less than 300° C (572° F).
Publication 2711-6.1
6-2
Installing the PV550 Terminal
Enclosures
Mount the PV550 terminal in a panel or enclosure to protect the
internal circuitry. The terminal meets NEMA Type 12/13 and 4X
(indoor ruse) ratings only when mounted in a panel or enclosure with
the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The
ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back panel of the terminal for wiring,
maintenance, installing a memory card and troubleshooting.
Required Tools
Mounting Dimensions
Other than the tools required to make the PV550 panel cutout, the
tools required for installation are:
•
7 mm (M4) deep well socket wrench or nut driver
•
small slotted screwdriver
•
torque wrench (in / lbs)
The illustration below shows mounting dimensions for the PV550
terminals.
PV550 Keypad, Keypad & Touch Screen Terminals
Top View
167 mm
(6.57 in)
106 mm
(4.17 in)
86 mm
(3.39 in)
266 mm
(10.47 in)
PV550 Touch Screen Terminals
Top View
150 mm
(5.92 in)
183 mm
(7.21 in)
Publication 2711-6.1
64 mm
(2.54 in)
82 mm
(3.20 in)
Installing the PV550 Terminal
Clearances
6-3
When installing the PV550 terminal, allow space for mounting, air
flow, maintenance, memory card and legend strip installation
PV550 Touch Screen Terminals
PV550 Keypad, Keypad & Touch Screen Terminals
Leave 25 mm (1.0 in)
for Mounting and Air Flow
Terminal Cutout
Terminal Cutout
Use full size template
shipped with terminal
Use full size template
shipped with terminal
Leave 25 mm (1.0 in)
for Mounting and Air Flow
Leave 38 mm (1.5 in)
for Mounting, Air Flow
and Wiring Connections
Back Clearance
Back Clearance
64 mm
(2.54 in)
109 mm
(4.3 in)
207 mm (8.15 in) is
required to insert and
remove a memory
card with the memory
card retainer.
86 mm
(3.39 in)
Card
Memory Card Retainer
Memory Card Retainer
Card
Publication 2711-6.1
6-4
Installing the PV550 Terminal
Cutout Dimensions
Use the full size template shipped with the PV550 terminal to mark
the cutout dimensions. Below is a reduce size cutout.
PV550 Keypad, Keypad & Touch Screen Terminals
243 mm
(9.55 in)
191 mm
(7.51 in)
25.9 mm
(1.02 in)
106 mm
(4.19 in)
85 mm
(3.33 in)
3.3 mm
(0.13 in)
4.8 mm dia
(0.188 in)
Front
Recommended Panel Cutout Dimensions
150 mm
(5.91 in)
3.3 mm
(0.13 in)
144 mm
(5.66 in)
PV550 Touch Screen Terminals
165 mm
(6.49 in)
4.8 mm dia.
(0.188 in)
98 mm
(3.86 in)
Publication 2711-6.1
158 mm
(6.20 in)
Recommended Panel Cutout Dimensions
R 1.8 mm
(0.07 in)
125 mm
(4.91 in)
Installing the PV550 Terminal
Installing the PV550 in a Panel
6-5
To install the PV550 terminal in a panel:
!
ATTENTION: Disconnect all electrical power from
the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components
that may already be installed in the panel.
Failure to follow this warning may result in personal
injury or damage to the panel components.
1. Cut an opening in the panel using the panel cutout provided with
the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on
the terminal as shown below. This gasket forms a compression
type seal. Do not use sealing compounds.
Sealing Gasket
Adhesive Legend Strip
(Keypad and Keypad &Touch Screen Terminals only)
3. On the keypad and keypad & touch screen terminals, secure the
ends of the legend strips to the legend strip adhesive.
4. Place the terminal in the panel cutout.
5. Verify that the opening is the proper size to clear the bezel and to
allow the gasket to contact the panel.
6. On the keypad and keypad & touch screen terminals, position the
ends of the legend inserts behind the panel cutout.
7. Install the self-locking nuts hand tight
Publication 2711-6.1
6-6
Installing the PV550 Terminal
PV550 Keypad, Keypad & Touch Screen Terminals.
Mounting Studs (3 Top, 3 Bottom)
Protective installation label
Self-locking nuts
(6 used, 8 provided)
PV550 Touch Screen Terminal
Protective installation label
Mounting Studs (2 left, 2 right)
Self-locking nuts
(4 used, 8 provided)
8. Alternately tighten the self-locking nuts until the terminal is held
firmly against the panel. Tighten nuts to a torque of 10 inchpounds. Do not over-tighten.
!
ATTENTION: Mounting nuts must be tightened to a
torque of 10 inch-pounds to provide a proper seal and
to prevent potential damage to the terminal. AllenBradley assumes no responsibility for water or chemical
damage to the terminal or other equipment within the
enclosure because of improper installation.
9. Remove the protective installation label covering the top vents of
the terminal.
!
Publication 2711-6.1
ATTENTION: Failure to remove the protective
installation label covering the top vents could result in
overheating and damage to the terminal.
Chapter
7
Installing the PV600 Terminal
Chapter Objectives
Hazardous Locations
This chapter describes how to mount the PV600 terminal in a panel or
enclosure including:
•
hazardous locations
•
enclosures
•
required tools
•
mounting dimensions
•
cutout dimensions
•
clearances
•
installing the PV600 terminal in a panel
See the nameplate label on terminal for certifications on hazardous
locations.
!
ATTENTION: In Class 1, Division 2 Hazardous
locations, the PanelView terminal must be wired per the
National Electric Code as it applies to hazardous
locations. Peripheral equipment must also be suitable
for the location in which it is installed.
The PV600 terminals have an operating temperature code of T4
(maximum operating temperature of 135° C or 275° F). Do not install
the terminals in environments where atmospheric gases have ignition
temperatures less than 135° C (275° F).
Enclosures
Mount the PV600 terminal in a panel or enclosure to protect the
internal circuitry. The terminal meets NEMA Type 12/13 and 4X
(indoor ruse) ratings only when mounted in a panel or enclosure with
the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The
ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back panel of the terminal for wiring,
maintenance, installing a memory card and troubleshooting.
Publication 2711-6.1
7-2
Installing the PV600 Terminal
Required Tools
Mounting Dimensions
Other than the tools required to make the PV600 panel cutout, the
tools required for installation are:
•
small slotted screwdriver
•
torque wrench (in. / lbs)
•
#2 phillips screwdriver
•
#2 phillips bit for torque wrench
The illustration below shows mounting dimensions for the PV600
terminals.
192 mm
(7.55 in)
290 mm
(11.40 in)
6.9 mm
(0.27 in)
Top View
116 mm
(4.57 in)
91 mm
(3.60 in)
Cutout Dimensions
Use the full size template shipped with the PV600 terminal to mark
the cutout dimensions. Below is a reduce size cutout.
167 mm
(6.57 in)
Recommended Panel Cut-out Dimensions
264 mm
(10.39 in)
Publication 2711-6.1
Installing the PV600 Terminal
Clearances
7-3
When installing the PV600 terminal, allow adequate space for
mounting, air flow, maintenance, memory card and legend strip
installation.
Side, Top and Bottom Clearances
Leave 51 mm (2.0 in)
for Mounting and Air Flow
Terminal Cutout - Front View
Leave 25 mm (1.0 in)
for Mounting and Air Flow
Use full size template
shipped with terminal
Leave 38 mm (1.5 in)
for Mounting, Air Flow
and Legend Insert
Leave 51 mm (2.0 in)
for Mounting and Wiring Connections
6.9 mm
(0.27 in)
Back Clearance
220 mm (8.65 in)
is required to
insert and remove
a memory card
with the memory
card retainer.
91 mm
(3.60 in)
Card
Memory Card Retainer
Publication 2711-6.1
7-4
Installing the PV600 Terminal
Installing the PV600 in a Panel
To install the PV600 terminal in a panel:
!
ATTENTION: Disconnect all electrical power from
the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components
that may already be installed in the panel.
Failure to follow this warning may result in personal
injury or damage to the panel components.
1. Cut an opening in the panel using the panel cutout provided with
the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on
the terminal as shown below. This gasket forms a compression
type seal. Do not use sealing compounds.
Sealing Gasket
3. Although the keypad legend strip can be installed any time, we
recommend that you install it after the terminal is installed.
4. Place the terminal in the panel cutout.
Publication 2711-6.1
Installing the PV600 Terminal
7-5
5. Install the 4 mounting clips (2 on top, 2 on bottom). The ends of
the clips slide into the slots on the terminal. Tighten the clip
mounting screws by hand until the gasket seal contacts the
mounting surface uniformly.
Protective installation labels
Install 4 mounting clips:
Top - left and right slots
Bottom - left and right slots
6. Alternately tighten the mounting clip screws to a torque of 10
inch-pounds. Do not over-tighten.
!
ATTENTION: Tighten mounting clips to a torque of
10 inch-pounds to provide a proper seal and to prevent
potential damage to the terminal. Allen-Bradley
assumes no responsibility for water or chemical damage
to the terminal or other equipment within the enclosure
because of improper installation.
7. Remove the 2 protective installation labels covering the top vents
of the terminal.
!
ATTENTION: Remove the protective installation
labels covering the top vents to prevent overheating and
damage to the terminal.
Publication 2711-6.1
7-6
Installing the PV600 Terminal
Publication 2711-6.1
Chapter
8
Installing the PV900/1000 Terminals
Chapter Objectives
Hazardous Locations
This chapter describes how to mount the PV900 and PV1000
terminals in a panel or enclosure including:
•
hazardous locations and enclosures
•
required tools
•
mounting dimensions
•
clearances
•
cutout dimensions
•
installing the PV900/PV1000 terminal in a panel
See the nameplate label on terminal for certifications on hazardous
locations.
!
ATTENTION: In Class 1, Division 2 Hazardous
locations, the PanelView terminal must be wired per the
National Electric Code as it applies to hazardous
locations. Peripheral equipment must also be suitable
for the location in which it is installed.
The PV900/PV1000 terminals have an operating temperature code of
T4 (maximum operating temperature of 135° C or 275° F). Do not
install the terminals in environments where atmospheric gases have
ignition temperatures less than 135° C (275° F).
Enclosures
The PV900/PV1000 terminal must be mounted in an environment
that provides IEC-1131-2 Pollution degree 2 protection.
Mount the terminal in a panel or enclosure to protect the internal
circuitry. The terminal meets NEMA Type 12/13 and 4X (indoor
ruse) ratings only when mounted in a panel or enclosure with the
equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The
ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back panel of the terminal for wiring,
maintenance, installing a memory card and troubleshooting.
Publication 2711-6.1
8-2
Installing the PV900/1000 Terminals
Required Tools
Mounting Dimensions
Other than the tools required to make the panel cutout, the tools
required for installation are:
•
small slotted screwdriver
•
torque wrench (in. / lbs) with slotted or phillips head driver
PV900 Terminals
The illustrations below show mounting dimensions for the PV900
monochrome and color terminals.
PV900 Touch Terminal Mounting Dimensions
6.9 mm
(0.27 in)
249 mm
(9.80 in)
Top View
112 mm
(4.40 in)
90 mm
(3.54 in)
336 mm
(13.24 in)
PV900 Keypad Terminal Mounting Dimensions
6.9 mm
(0.27 in)
249 mm
(9.80 in)
406 mm
(15.97 in)
Publication 2711-6.1
90 mm
(3.54 in)
Top View
112 mm
(4.40 in)
Installing the PV900/1000 Terminals
8-3
PV1000 Terminals
The illustrations below show the mounting dimensions for the
PV1000 grayscale and color terminals.
PV1000 Touch Terminal Mounting Dimensions
6.9 mm
(0.27 in)
282 mm
(11.11 in)
Top View
112 mm
(4.40 in)
90 mm
(3.54 in)
370 mm
(14.58 in)
PV1000 Keypad Terminal Mounting Dimensions
6.9 mm
(0.27 in)
282 mm
(11.11 in)
90 mm
(3.54 in)
Top View
112 mm
(4.40 in)
423 mm
(16.64 in)
Publication 2711-6.1
8-4
Installing the PV900/1000 Terminals
Clearances
Allow adequate space for mounting, air flow, maintenance, memory
card and legend strip installation.
Important: If using a memory card and/or memory card retainer,
allow a back clearance to load the card.
Side, Top and Bottom Clearances
Leave 51 mm (2.0 in)
for Mounting and Air Flow
Terminal Cutout - Front View
Leave 51 mm (2.0 in)
for Mounting and Air Flow
Use full size template
shipped with terminal
Leave 51 mm (2.0 in)
for Mounting, Air Flow
and Legend Insert
Leave 51 mm (2.0 in)
for Mounting and Wiring Connections
Back Clearance
6.9 mm
(0.27 in)
90 mm
(3.54 in)
Memory Card Retainer
Publication 2711-6.1
Card
222 mm (8.73 in) is
required to insert and
remove a memory
card with the memory
card retainer.
Installing the PV900/1000 Terminals
Cutout Dimensions
8-5
Use the full size template shipped with the PV900 and PV1000
terminals to mark the cutout dimensions. The following illustrations
show reduced cutouts for these terminals with dimensions.
PV900 Panel Cutout Dimensions
PV900 Keypad Terminals
224 mm
(8.8 in)
Recommended Panel Cut-out Dimensions
PV900 Touch Screen Terminals
224 mm
(8.8 in)
375 mm
(14.75 in)
Recommended Panel Cut-out Dimensions
305 mm
(12.00 in)
PV1000 Panel Cutout Dimensions
PV1000 Keypad Terminals
257 mm
(10.11 in)
Recommended Panel Cut-out Dimensions
390 mm
(15.35 in)
PV1000 Touch Screen Terminals
257 mm
(10.11 in)
Recommended Panel Cut-out Dimensions
338 mm
(13.29 in)
Publication 2711-6.1
8-6
Installing the PV900/1000 Terminals
Installing the
PV900/PV1000 in a Panel
To install the PV900/PV1000 terminal in a panel:
!
ATTENTION: Disconnect all electrical power from
the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components
that may already be installed in the panel.
Failure to follow this warning may result in personal
injury or damage to the panel components.
1. Cut an opening in the panel using the panel cutout provided with
the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on
the terminal as shown below. This gasket forms a compression
type seal. Do not use sealing compounds.
Sealing Gasket
3. Although the keypad legend strip can be installed any time, we
recommend that you install it after the terminal is installed.
4. Place the terminal in the panel cutout.
Publication 2711-6.1
Installing the PV900/1000 Terminals
8-7
5. Install the 6 mounting clips (2 on top, 2 on bottom, 1 on each
side). The ends of the clips slide into the slots on the terminal.
Tighten the clip mounting screws by hand until the gasket seal
contacts the mounting surface uniformly.
Protective installation labels
Install 6 mounting clips:
Top - left and right slots
Bottom - left and right slots
Sides - left and right
6. Alternately tighten the mounting clip screws to a torque of 10
inch-pounds. Do not over-tighten.
!
ATTENTION: Tighten mounting clips to a torque of
10 inch-pounds to provide a proper seal and to prevent
potential damage to the terminal. Allen-Bradley
assumes no responsibility for water or chemical damage
to the terminal or other equipment within the enclosure
because of improper installation.
7. Remove the 2 protective labels covering the top vents of the terminal.
!
ATTENTION: Remove the protective installation
labels covering the top vents to prevent overheating and
damage to the terminal.
Publication 2711-6.1
8-8
Installing the PV900/1000 Terminals
Publication 2711-6.1
Chapter
9
Installing the PV1400 Terminal
Chapter Objectives
Enclosures
This chapter describes how to mount the PV1400 terminal in a panel
or enclosure including:
•
enclosures
•
recommended tools
•
mounting dimensions
•
clearances
•
cutout dimensions
•
installing the PV1400 terminal in a panel
The PV1400 terminal must be mounted in an environment that
provides IEC-1131-2 Pollution degree 2 protection.
Mount the PV1400 terminal in a panel or enclosure to protect the
internal circuitry. The terminal meets NEMA Type 12/13 and 4X
(indoor ruse) ratings only when mounted in a panel or enclosure with
the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The
ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back sides of the terminal. Access is
required for wiring, routine maintenance, adjusting brightness/
contrast, installing a memory card and troubleshooting.
Required Tools
In addition to the tools required to make the panel cutout, you need
the tools below.
For clip mounting:
•
socket screwdriver (phillips head or slotted)
•
16-inch (406 am) extension rod (minimum)
•
socket driver (in/lab torque wrench recommended)
For stud mounting:
•
7/32 and 3/8 inch socket
•
16-inch (406 mm) extension rod (minimum)
•
socket driver (in/lb torque wrench recommended)
Publication 2711-6.1
9-2
Installing the PV1400 Terminal
Mounting Dimensions
The illustrations below show mounting dimensions for the PV1400
terminals.
PV1400 Touch Terminal Mounting Dimensions
3.3 mm
(0.13 in)
355 mm
(13.97 in)
Top View
394 mm
(15.53 in)
370 mm
(14.58 in)
441 mm
(17.37 in)
PV1400 Keypad Terminal Mounting Dimensions
3.3 mm
(0.13 in)
355 mm
(13.97 in)
483 mm
(19.0 in)
Publication 2711-6.1
370 mm
(14.58 in)
Top View
394 mm
(15.53 in)
Installing the PV1400 Terminal
Clearances
9-3
Allow adequate space for mounting, air flow, maintenance, adjusting
brightness/contrast, memory card and legend strip installation.
Important: If using a memory card, allow a back clearance to load
the card.
Side, Top and Bottom Clearances
Leave 51 mm (2.0 in)
for Mounting and Air Flow
Terminal Cutout - Front View
Use full size template
shipped with terminal
Leave 51 mm (2.0 in) for Mounting
Leave 51 mm (2.0 in)
for Mounting and Air Flow
3.3 mm
(0.13 in)
Back Clearance
370 mm
(14.58 in) Approximately
400 mm (15.74 in)
is required to
insert and load a
memory card.
Card
Publication 2711-6.1
9-4
Installing the PV1400 Terminal
Cutout Dimensions
Use the full size template provided with the terminal to mark cutout
dimensions. The illustration below shows reduced size cutouts with
dimensions.
PV1400 Keypad Terminals
419 mm
(16.50 in)
110 mm
(4.35 in)
221 mm
(8.70 in)
170 mm
(6.70 in)
7/32 in (5.56 mm) Typical
18 Holes
140 mm
(5.50 in)
38 mm
1.50 in
305 mm
(12.0 in)
Ignore stud holes if
mounting terminal
using panel clips.
233 mm
(9.16 in)
PV1400 Touch Screen Terminals
391 mm
(15.40 in)
127 mm
(5.0 in)
169 mm
(6.65 in)
140 mm
(5.50 in)
Ignore stud holes if
mounting terminal
using panel clips.
305 mm
(12.0 in)
212 mm
(8.35 in)
Publication 2711-6.1
7/32 in (5.56 am) Typical
18 Holes
Installing the PV1400 Terminal
Installing the PV1400 in a Panel
9-5
This section gives procedures for mounting a PV1400 using:
•
mounting clips (10 shipped with terminal, 10 required)
•
mounting studs (ordered separately, Catalog No. 2711-NP3)
!
ATTENTION: Disconnect all electrical power from
the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components
that may already be installed in the panel.
Failure to follow this warning may result in personal
injury or damage to the panel components.
To install the PV1400 terminal in a panel using clips:
1. Cut an opening in the panel using the panel cutout provided with
the terminal. Remove any sharp edges or burrs. Do not drill the
mounting stud holes if you are using clips.
2. Make sure the sealing gasket is properly positioned on the terminal as shown below. This gasket forms a compression type seal.
Do not use sealing compounds.
Sealing Gasket
3. Although the keypad legend strip can be installed any time, we
recommend that you install them after the terminal is installed.
4. Place the PV1400 in the panel cutout. The terminal will snap into
the panel as the temporary retaining tabs lock against the panel.
Note: The PV1400 has 2 metal tabs (on bottom edge) that
temporarily lock the terminal against the panel. These tabs only
facilitate installation of the mounting hardware. The tabs are not
designed to provide permanent mounting.
Publication 2711-6.1
9-6
Installing the PV1400 Terminal
5. Install the 10 mounting clips (3 on top, 3 on bottom, 2 on each
side). The ends of the clips slide into slots on the terminal.Tighten
the clip mounting screws hand tight.
Install 10 Mounting Clips
= Recommended
Placement
Keypad Version
Touch Screen Version
6. Alternately tighten the mounting clip screws until the terminal is
held firmly against the panel. Tighten mounting screws to a
torque of 10 inch-pounds. Do not over-tighten.
!
Publication 2711-6.1
ATTENTION: Tighten mounting clips to a torque of
10 inch-pounds to provide a proper seal and to prevent
potential damage to the terminal. Allen-Bradley
assumes no responsibility for water or chemical damage
to the terminal or other equipment within the enclosure
because of improper installation.
Installing the PV1400 Terminal
9-7
To install the PV1400 terminal in a panel using mounting studs:
1. Cut an opening in the panel using the panel cutout shipped with
the terminal. Carefully drill 5.56 mm (7/32 inch) holes for studs
as indicated.
2. Install the mounting studs (Catalog No. 2711-NP3) using a 7/32inch socket on the end of the stud. Turn stud clockwise and
tighten to approximately 10-inch pounds (1.1 N•m).
Bezel
Mounting Studs
(Qty 18 for Keypad, 12 for Touch
Gasket
Panel or Enclosure
Self-locking Nuts
Spacer
3. Make sure the sealing gasket is properly positioned on the terminal. This gasket forms a compression type seal (NEMA Type 4).
Do not use sealing compounds
!
ATTENTION: Be careful not to damage the sealing
gasket when installing or removing studs. A damaged
seal may result in damage to the PanelView terminal
and other panel components due to a leaking seal.
4. Place the PV1400 in the panel cutout aligning the studs with the
mounting holes.
Publication 2711-6.1
9-8
Installing the PV1400 Terminal
5. Install the self-locking nuts hand tight.
ATTENTION: Tighten mounting nuts to a torque of
10 inch-pounds (1.1 N•m) to provide a proper seal and
prevent potential damage to the terminal. Allen-Bradley
assumes no responsibility for water or chemical damage
to the terminal or other equipment within the enclosure
because of improper installation.
!
6. Alternately tighten the self-locking nuts (use 3/8 inch socket)
until the PV1400 is held firmly against the panel. (The recommended tightening sequence is shown below).
The studs have an integral spacer that prevents the gasket from
being over-compressed. The amount of torque required increases
significantly as the gasket reaches the proper compression.
Tighten nuts to a torque of 10 inch-pounds (1.1 N•m).
18
9
1
5
9
13
16
15
7
8
11
12
17
10
2
6
14
5
8
7
3
Recommended
Torque Sequence
Keypad Terminals
4
1
4
Recommended
Torque Sequence
Touch Terminals
3
11
12
10
2
6
Note that sequence starts at center studs and continues to the corner studs.
Publication 2711-6.1
Chapter
10
Making Terminal Connections
Chapter Objectives
Wiring and Safety Guidelines
This chapter describes network and device connections for PanelView
terminals.
•
wiring and safety guidelines
•
Remote I/O connections
•
DH+ connections
•
DH-485 connections
•
RS-232 (DH-485) connections
•
ControlNet connections
•
DeviceNet connections
•
DF1 connections
•
Computer or printer connection to RS-232 serial port
Use publication NFPA 70E, Electrical Safety Requirements for
Employee Workplaces when wiring the PanelView terminals. In
addition to the NFPA general guidelines:
•
route communication cables to terminal by a separate path from
incoming power.
!
ATTENTION: Do not run signal wiring and power
wiring in the same conduit.
•
where power and communication lines must cross, they should
cross at right angles. Communication lines can be installed in the
same conduit as low level DC I/O lines (less than 10 volts).
•
grounding minimizes noise from Electromagnetic Interference
(EMI) and is a safety measure in electrical installations.
•
use the National Electric Code published by the National Fire
Protection Association as a source for grounding.
Publication 2711-6.1
10-2
Making Terminal Connections
Remote I/O Terminal Connections
This section describes connections for the Remote I/O PanelView
terminals including:
•
Remote I/O port
•
supported controllers
•
making Remote I/O connections
•
Remote I/O Pass-Through
Remote I/O Terminal Ports
The Remote I/O versions of the PanelView terminal (catalog numbers
ending in 1) have a Remote I/O port and an RS-232 port.
Use the Remote I/O port to:
•
communicate with the Remote I/O scanner port on a PLC
controller
•
communicate with SLC controllers using a 1747-SN Remote I/O
scanner module
•
communicate with other Remote I/O scanners
•
transfer applications using Remote I/O Pass-Through
Use the RS-232 Port to:
•
transfer PanelView applications between a computer and the
terminal.
•
connect a printer.
For details on connecting to the RS-232 port, see the last section in
this chapter.
PanelView 550
Keypad (2711-K5A1) Shown
PanelView 900
Keypad (2711-K9A1) Shown
Remote I/O Port
Remote I/O Port
Publication 2711-6.1
RS-232 Port
RS-232 Port
Making Terminal Connections
10-3
Supported Controllers
The Remote I/O terminal connects to any Allen-Bradley 1771
Remote I/O link. Applicable host controllers include almost all AllenBradley PLCs, computers, VME controllers, and DEC Q-Bus
controllers with a Remote I/O scanner module. New PLC product
releases that support 1771 Remote I/O will also work with
PanelView.
When connecting a PanelView terminal to a controller refer to the
user manual for your controller or scanner module for connection
diagrams and any Remote I/O limitations. The table below provides a
summary of possible connections.
Controller
Scanner
PLC-5/11, 5/151,
5/20, 5/25,
5/30, 5/60, 5/250
PLC Integral
1771-SN
Connect PanelView terminals directly
to the Remote I/O port (scanner
mode). Connect PanelView terminals through the 1771-SN subscanner module.
PLC-5/10, 5/12
1771-SN
Connect PanelView terminals
through the 1771-SN subscanner
module.
1771-SN or
Connect PanelView terminals to the
PLC-2 family of processors through a
1771-SN I/O subscanner module.
PLC-2
1772-SD22
PLC-3 and
PLC-3/10
None
PLC-3/10
Remote I/O
Scanner3
Comments
Connect PanelView terminals directly
to a PLC-3.
Connect PanelView terminals to the
PLC-3/10 through the Remote I/O
scanner.
SLC-5/00, 5/02,
5/03, 5/04,
5/05
1747-SN
Connect PanelView terminals
through the 1747-SN subscanner
module. Each module provides an
additional Remote I/O link for up to 4
racks.
Important: Only Series B and later
versions of the 1747-SN subscanner
support block transfers.
IBM PC
6008-SI
6008-SI I/O scanner is compatible
with IBM PC or compatible computers. The scanner provides a computer access to the 1771 Remote I/O
link.
VME
6008-SV
6008-SV I/O scanner provides
access to the 1771 Remote I/O link
for VME controllers.
DEC Q-BUS
6008-SQ
6008-SQ I/O scanner provides
access to the 1771 Remote I/O link
for DEC Q-BUS controllers.
1 If using a PLC-5/15 with partial rack addressing and block transfers, you must use Series B, Rev. J or later.
2
If using a 1775-SD2 Remote Scanner/Distribution Panel, use revision 3 or later.
3
If using a 1775-S4A Remote Scanner/Distribution Panel, user Series B or later.
Publication 2711-6.1
10-4
Making Terminal Connections
Making Remote I/O Connections
To connect a PanelView terminal to a Remote I/O scanner, use cable
Catalog No. 1770-CD (equivalent to Belden 9463). The maximum
cable length (link distance) is determined by the baud rate.
•
2,800 meters (10,000 feet) for 57.6K baud
•
1,400 meters (5,000 feet) for 115.2K baud
•
700 meters (2,500 feet) for 230.4K
See Programmable Controller Wiring and Grounding Guidelines
(Publication 1770-4.1). The user manual for the I/O scanner module
also provides cabling information.
PanelView 550
Keypad (2711-K5A1) Shown
PanelView 900
Keypad (2711-K9A1) Shown
Remote I/O Port
3-pin Terminal Block Connector
Clear = 2
Shield
Blue = 1
To PLC or Scanner Remote I/O Port
Connector
(One provided with each terminal)
Cable (Catalog No. 1770-CD)
Note: The polarity of the Remote I/O Connector on the PanelView
terminal is reversed from the PLC Scanner connector. However, the
polarity is the same as the scanner card connection to the SLC.
Publication 2711-6.1
Making Terminal Connections
10-5
Remote I/O Pass-Through
Remote I/O terminals allow the transfer of applications from a
computer on the Allen-Bradley DH+ link to a PLC-5 controller. The
controller passes data to the PanelView terminal over the Remote I/O
network.
PLC-5
DH+
Computer
Remote I/O
Pass-Through
Remote I/O Network
PanelView
To transfer an application using Remote I/O Pass-Through:
1. A Data Highway Plus Interface Module must be installed in the
computer. Allen-Bradley offers a variety of interface cards for a
DH+ connection between a computer and a controller.
2. The appropriate communication driver must be configured on the
computer.
3. Connect the computer to the PLC. See the instruction sheets provided with the communication module or card to select the proper
cable. Connect the cable between the computer and the controller.
4. Pass-Through must be enabled for the terminal. Check the RIO
Configuration screen on the terminal’s Configuration Mode
menu. Pass-Through is enabled using the out-of-box application
provided with the terminal or when defining Remote I/O parameters in the PanelBuilder software.
5. Refer to the online help in the PanelBuilder software for procedures on how to transfer applications using Pass-Through.
Publication 2711-6.1
10-6
Making Terminal Connections
DH-485 Terminal Connections
This section describes connections for the DH-485 PanelView
terminals.
•
DH-485 terminal ports
•
Connecting to a single SLC controller (Point-to-Point)
•
Connecting to a DH-485 network
•
Connecting a Hand-held terminal
•
Connecting a computer
DH-485 Terminal Ports
DH-485 PanelView terminals with catalog numbers ending in 2 have
two DH-485 ports. Terminals with catalog numbers ending in 3 also
have an RS-232 printer port.
Use the DH-485 Communications port to:
• communicate with a single or multiple SLC controllers over a
DH-485 network.
Use the DH-485 SLC Programming connector to:
• upload/download PanelView applications
•
monitor SLC operation, enter/modify SLC programs, test
network devices
Use the RS-232 Printer port to:
• connect a printer that supports the IBM enhanced character set.
For details on connecting to the RS-232 port, see the last section
in this chapter.
The DH-485 communications port and programming connector may
appear in different locations on specific terminals. Identify the ports
by their size and shape or by the port labels.
PanelView 550
Keypad (2711-K5A3) Shown
PanelView 900
Keypad (2711-K9A3) Shown
RS-232 Printer Port
RS-232 Printer Port
DH-485
Communications Port
DH-485 SLC
Programming Connector
Publication 2711-6.1
DH-485 SLC
Programming Connector
DH-485
Communications Port
Making Terminal Connections
10-7
Connecting to a Single SLC Controller (Point-to-Point)
To connect a DH-485 terminal to a single SLC controller use one of
these cables:
•
0.3 meter (1 foot) Catalog No. 1747-C11
•
1.83 meter (6 foot) Catalog No. 1747-C10
•
6.1 meter (20 foot) Catalog No. 1747-C20
PanelView 900
Touch Screen (2711-T9A2) Shown
SLC
SLC 500
Communications Connector
DH-485 Communications Port
Pin 1
Cable, Catalog No. 1747-C10
Cable, Catalog No. 1747-C11
Cable, Catalog No. 1747-C20
Pin 8
To PanelView Terminal
8-pin Female Plug
Connection Diagram
Pin #
Connect to:
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
Pin #
Pin 1
Pin 8
Side shown is opposite latch
To SLC Communications Connector
8-pin, Male, Modular Plug
The DH-485 connectors are not electrically isolated. If electrical
isolation is required, use Link Couplers (Catalog No. 1747-AIC) as
shown on next page.
!
ATTENTION: Electrical isolation using Link
Couplers (Catalog No. 1747-IC) is required where the
distance between the PanelView terminal and the SLC
is greater than 6.1 meters (20 feet).
Publication 2711-6.1
10-8
Making Terminal Connections
Connecting to a DH-485 Network
This section shows how to connect a DH-485 terminal to multiple
SLC controllers on a DH-485 network through the AIC Link Coupler.
Link Coupler
Catalog No. 1747-AIC
Network with Link Couplers
SLC
PanelView 900
Touch Screen (2711-T9A2) Shown
Power Source
or 1747-NP1
CableCatalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
Belden 9842
SLC 5/01
Important: The DH-485 network cable requires proper shielding,
grounding and termination. Refer to Data Highway / Data
Highway Plus / Data Highway-485 Cable Installation
Manual (Publication No. 1770-6.2.2).
Publication 2711-6.1
Making Terminal Connections
10-9
The illustration below shows how to connect a DH-485 terminal to a
Micrologix or SLC controller using the AIC+ Link Coupler (Catalog
No. 1761-NET-AIC).
AIC+
MicroLogix 1000
Catalog No. 1761-NET-AIC
CableCatalog No. 1761-AS03
Catalog No. 1761-As09
Catalog No. 1761-CBL-AS08
Catalog No. 1761-CBL-AS09
Catalog No.
1761-CBL-PM02
1761-CBL-AP00
PanelView 900
Touch Screen (2711-T9A2) Shown
SLC 5/03, 5/04, 5/05
AIC+
Catalog No. 1761-NET-AIC
CableCatalog No. 1761-AS03
Catalog No. 1761-As09
Catalog No. 1761-CBL-AS08
Catalog No. 1761-CBL-AS09
Channel 0 Port
Catalog No. 1747-CP3
To 24V DC Power
PanelView 900
Touch Screen (2711-T9A2) Shown
AIC+
AIC
Catalog No. 1747-AIC
Catalog No. 1761-NET-AIC
MicroLogix 1000
Belden 9842
To PanelView
Catalog No.
1761-CBL-PM02
1761-CBL-AP00
PanelView 900
Do not connect the PanelView to
Port 3 of the AIC+ when Port 3 is
networked to other devices.
CableCatalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
Publication 2711-6.1
10-10
Making Terminal Connections
Connecting a Computer
On DH-485 terminals, PanelView applications are transferred:
•
through the DH-485 programming connector to the terminal.
•
through any node on a DH-485 network.
To connect a computer to the PanelView terminal, you need:
•
a cable (same cables used to transfer applications from APS
software to SLC)
- 0.3 meter (1 foot) cable, Catalog No. 1747-C11
- 1.83 meter (6 foot) cable, Catalog No. 1747-C10
- 6.1 meter (20 foot) cable, Catalog No. 1747-C20
•
Personal Computer Interface Converter (PIC), Catalog No. 1747PIC. The PIC connects to the computer. The cable connects the
PIC to the DH-485 programming connector.
Personal Computer Interface Converter (PIC)
The Personal Computer Interface Converter (PIC) receives power
from a controller through DH-485 connections. When connecting a
computer directly to a PanelView terminal without a controller
connected, you need to use a power supply (Catalog No. 1747-NP1).
The power supply connects to the DH-485 communications connector
with the same cables used to connect an SLC.
Important: The terminal must be connected to an SLC, DH-485
network, or power supply (Catalog No. 1747-NP1). This
connection provides power to the PIC.
Connecting Earth Ground to PanelView Terminals
When using the 1747-PIC converter with the PV600, PV900, PV1000
color and PV1000 grayscale terminals, you must connect the Earth
Ground terminal on the back of the terminal to Earth Ground.
Connect the Earth Ground terminal using 14-gauge, stranded wire no
longer than 1 meter (40 inches).
Earth Ground Terminal
PV900 Color Terminals
Publication 2711-6.1
Making Terminal Connections
10-11
Connecting a Computer to DH-485 Connector using a Power Supply
PanelView 900
Keypad (2711-K9A2) Shown
PanelBuilder
Wallmount Power Supply
(Catalog No. 1747-NP!)
To DH-485
Programming Connector
25-pin to 9-pin Adapter
(if required)
Personal Computer
Interface Converter
(Catalog No. 1747-PIC)
To DH-485
Communications Port
Cable
Catalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
Connecting a Computer to DH-485 Connector using a DH-485 Powered Device
PanelView 900
Keypad (2711-K9A2) Shown
PanelBuilder
SLC 500 or
DH-485 Network
To DH-485
Programming Connector
To DH-485
Communications Port
(if required)
25-pin to 9-pin Adapter Personal Computer
Interface Converter
(Catalog No. 1747-PIC)
Note: The computer can connect to any node on the
network. It is not necessary to directly connect the computer to the PanelView terminal.
Cable
Catalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
Publication 2711-6.1
10-12
Making Terminal Connections
Connecting a Hand-Held Terminal
To connect a Hand-Held Terminal (HHT) to the PanelView terminal,
use cable Catalog No. 1747-C10. One end of the cable connect to the
HHT connector and the other end connects to the DH-485
programming connector on the terminal. All power is supplied to the
HHT through the cable.
Important: The PanelView terminal must be connected to an SLC,
DH-485 network or power supply. This connection
provides power for the HHT.
PanelView 900
Touch Screen (2711-T9A2) Shown
Hand-Held Terminal
Catalog No. 1747-PT1
To DH-485
Programming Connector
DH-485 Communications Port
Must be connected to an SLC, DH-485 network,
or wallmount power supply (Cat. No. 1747-NP1)
to provide power for the HHT.
Cable, 1.83 meters (6 feet) Catalog No. 1747-C10
Publication 2711-6.1
Making Terminal Connections
DH+ Terminal Connections
10-13
This section describes connections for the DH+ PanelView terminals
including:
•
DH+ connectors
•
typical DH+ system configuration
•
making DH+ connections
DH+ Terminal Ports
The DH+ versions of the PanelView terminals have a DH+ port and
an RS-232 port.
Use the DH+ port to:
• communicate with a PLC-5 controller on the Allen-Bradley DH+
link via the processor’s DH+ port.
•
communicate with an SLC 5/04 controller (Channel 0 port) on the
Allen-Bradley DH+ link via the processor’s DH+ port.
Use the RS-232 port to:
• transfer PanelView applications between a computer and the
DH+ terminal using a direct connection.
•
connect a printer. For connection details, see the last section in
this chapter.
PanelView 550
Keypad (2711-K5A8) Shown
PanelView 900
Keypad (2711-K9A8) Shown
DH+ Port
DH+ Port
RS-232 Port
RS-232 Port
Publication 2711-6.1
10-14
Making Terminal Connections
Typical DH+ System Configuration
For more information on the Allen-Bradley DH+ link, refer to:
•
1785-5.7 Enhanced PLC-5 Programmable Controllers Installation
Instructions
•
1770-6.2.2 Data Highway/Data Highway Plus/Data Highway II/
Data Highway 485 Cable Installation Manual.
Download application to PanelView
1 over local DH+ link
2
over a direct serial link
PLC-5
SLC 5/04
or
DH+ RSLinx Port
DH+ communication card
installed in computer
1
1
PanelView 900 DH+ Terminal
PanelView 550 DH+ Terminal
DH+ Port
DH+ Port
Computer for developing
PanelView applications
2
Publication 2711-6.1
RS-232 Port
Serial Link
Making Terminal Connections
10-15
Making DH+ Connections
Use the Belden 9463 twin axial cable (1770-CD) to connect a DH+
PanelView terminal to the DH+ link.
You can connect a DH+ link in 2 ways:
•
trunk line/drop line - from the drop line to the connector screw
terminals on the DH+ connectors of the processor
•
daisy chain - to the connector screw terminals on the DH+
connectors on the processor
Follow these guidelines when installing DH+ communication links:
•
do not exceed these cable lengths:
- trunk line-cable length: 3,048 m (10,000 cable ft)
- drop-cable length: 30.4 m (100 cable-ft)
•
do not connect more than 64 stations on a single DH+ link
PLC-5/30, -5/40, -5/46, -5/40L, -5/60, -5/60C
-5/60L, -5/80, 5/80C, -5/86 Processor
PLC 5/11, -5/20, -5/26 Processor
PanelView 550 DH+ Terminal
2
Clear 1
Shield SH
Blue 2
1770-CD
(Belden Cable)
1
Blue 2
Shield SH
Clear 1
82Ω or 150Ω resistor
PanelView 900 DH+ Terminal
2
Blue
1
2
Shield SH
Clear 1
82Ω or 150Ω resistor
Publication 2711-6.1
10-16
Making Terminal Connections
RS-232 Terminal Connections
This section describes connections for the RS-232 PanelView
terminals including:
•
RS-232 ports
•
connecting to Channel 0 of an SLC 5/03, 5/04, 5/05 Controller
(point-to-point)
•
connecting to a MicroLogix Controller
•
connecting a computer
•
connecting to a DH+ link
RS-232 Terminal Ports
RS-232 versions of the PanelView terminals with catalog numbers
ending in 5 have a single RS-232 communications port. Terminals
with catalog numbers ending in 9 have an RS-232 communications
port and an RS-232 printer port.
Use the RS-232 communicatons port to:
• communicate with a single SLC 5/03, 5/04, or 5/05 controller
(Channel 0 port) using point-to-point communications
•
download/upload PanelView applications
Use the RS-232 printer port to:
• connect a printer that supports the IBM enhanced character set.
For connection details, see the last section in this chapter.
The RS-232 communications port and the printer port are reversed on
the PanelView 550 touch screen terminals.
PanelView 550
Keypad (2711-K5A9) Shown
PanelView 900
Keypad (2711-K9A9) Shown
RS-232 Printer Port
RS-232 Printer Port
Publication 2711-6.1
RS-232 Communications Port
RS-232 Communications Port
Making Terminal Connections
10-17
Connecting to an SLC 5/03, 5/04, 5/05 Controller (Point-to-Point)
This section shows how to connect an SLC-5/03, 5/04 or 5/05
controller to the RS-232 PanelView terminal for point-to-point
communications. On terminals with two ports, use the RS-232
Communications Port.
Use one of these cables:
•
5 meter (16.4 foot) Catalog No. 2711-NC13
•
10 meter (32.7 foot) Catalog No. 2711-NC14
•
3 meter (10 foot) Catalog No. 2706-NC13
PanelView 900
Touch Screen (2711-T9A5) Shown
SLC 5/03, 5/04, 5/05
RS-232 Communications Port
5
11
9
6
To PanelView Terminal
9-pin, Male, D-Shell Connector
Channel 0 Port
RS-232 Connector
5
Cable, Catalog No. 2711-NC13
Cable, Catalog No. 2711-NC14
Cable, Catalog No. 2706-NC13
1
9
6
To SLC 5/03, 5/04, 5/05 Channel 0 Port
9-pin, Male, D-Shell Connector
Pin #
Pin #
Required pins
1
1
2 Data In (RXD)
Data Out (TXD) 2
3 Data Out (TXD)
Data In (RXD) 3
4
4
Signal Common 5
5 Signal Common
6
6
7
7
8
8
9
9
Important: You must configure the Channel 0 Port of the SLC 5/03,
5/04, 5/05 controller for DH-485 communications using
the RSLogix 500, or AI500 software.
Publication 2711-6.1
10-18
Making Terminal Connections
Connecting to a MicroLogix Controller
This section shows how to connect the RS-232 or DH-485 version of
the PanelView terminal to a MicroLogix 1000 controller through an
AIC+ Link Coupler.
AIC+
MicroLogix 1000
Catalog No. 1761-NET-AIC
CableCatalog No. 1761-CBL
Catalog No. 1761-AS03
Catalog No. 1761-As09
Catalog No.
1761-CBL-PM02
1761-CBL-AP00
PanelView 900
Catalog No. 1746-CP3
(2711-xxx5 or -xxx9)
RS-232 Communications Cables
Catalog No. 2711-NC13
Catalog No. 2711-NC14
Catalog No. 2706-NC13
Computer
Note: On PanelView 550 terminals, pin 8
on the RS-232 connector is pulled high.
Do not use the 2711-NC13 cable.
Connecting a Computer
This section shows how to connect a computer to the RS-232
PanelView terminal for transferring applicatons.
Computer
PanelView 900
Touch Screen (2711-T9A5) Shown
PanelBuilder
To Comm 1 or Comm 2 Port
To RS-232 Communications Port
9-pin to 25-pin Adapter
(if required)
Publication 2711-6.1
RS-232 Communications Cables
Catalog No. 2711-NC13, 5 m (16.4 ft)
Catalog No. 2711-NC14, 10 m (32.7 ft)
Catalog No. 2706-NC13, 3 m (10 ft)
Making Terminal Connections
10-19
Connecting to a DH+ Link
This section shows connections for transferring applications between
a computer on the Allen-Bradley DH+ link and an RS-232 PanelView
terminal, through an SLC 5/04 controller.
The RS-232 Communications port on the terminal connects to the
CH0 port of the controller using one of the cables listed below.
PanelView 900
Touch Screen (2711-T9A5) Shown
Computer
PanelBuilder
To 1784-KT/B Port
To RS-232 Communications Port
DH+ Network Cable
Catalog No. 1784-CP6
or
Catalog No. 1784-CP
with 1784-CP7 Adapter
SLC 5/04 CPU
Cable
Catalog No. 2706-NC13,
2711-NC13,-NC14
To CH1 Port
To CH0 Port
Publication 2711-6.1
10-20
Making Terminal Connections
ControlNet Connections
This section describes connections for the ControlNet PanelView
terminals including:
•
ControlNet Protocol
•
Compatible ControlNet Controllers
•
ControlNet ports on the PanelView terminal
•
Typical ControlNet network
•
Making ControlNet connections
Related Information
For more information on ControlNet products, refer to the following
publications.
•
ControlNet System Overview (Publication 1786-2.9)
•
ControlNet System Planning and Installation Manual (17866.2.1)
•
ControlNet Cable System Component List (AG-2.2)
The Allen-Bradley website (www.ab.com) provides information and
product descriptions of ControlNet products. Under the Products and
Services heading, select Communications
ControlNet Protocol
The PanelView terminal supports release 1.5 of ControlNet.
Unscheduled (peer) addressing of tags is supported. Scheduled (I/O)
addressing is not supported.
ControlNet allows a flexible control architecture that can work with
multiple processors and up to 99 nodes (via taps) anywhere along the
trunk cable of the network. There is no minimum tap separation and
you can access the ControlNet network from every node (including
adapters).
Publication 2711-6.1
Making Terminal Connections
10-21
Compatible ControlNet Controllers
The ControlNet PanelView supports unscheduled PCCC
(Programmable Controller Communication Command) messaging
with the following controllers:
•
PLC-5/20C
•
PLC-5/40C
•
PLC-5/60C
•
PLC-5/80C
ControlNet Terminal Ports
ControlNet versions of the PanelView terminal (catalog numbers
ending in 15) have a ControlNet communication port and an RS-232
serial port.
•
Use the ControlNet port to connect to devices on a DeviceNet
network.
•
Use the RS-232 port to transfer applications between a computer
and the terminal or to connect a printer.
For details on connecting to the RS-232 port, see the last section
in this chapter.
PanelView 900 shown
ControlNet
Communications Port
RS-232 Port
Publication 2711-6.1
10-22
Making Terminal Connections
Typical ControlNet Network
Below is a typical ControlNet network with a PanelView terminal
installed on a network drop.
PanelView 900
2711-T9A15 Shown
ControlNet Port
BNC Coaxial Cable
RS-232 Port
Printer
Computer for developing
PanelView applications
or
1784-KTC(X) Card to
ControlNet (RSLinx) & WinPFT
Serial Link
ControlLogix 5550
1784-CNB Module
Personal
Computer
Personal
Computer
1784-KTC(X)
Interface Card
PLC-5/40C
Serial Link
1770-KFC
1786-RG6 Cable
PLC-5/80C
Flex I/O
(1784-ACN)
= Taps
= Terminators
Publication 2711-6.1
Repeater
(1786-RPT)
Making Terminal Connections
10-23
Making ControlNet Connections
Use the pinout information below to connect the PanelView to a
ControlNet network.
Important: Follow the ControlNet network layout and design as
specified in the ControlNet Cable System Planning and
Installation Manual (Publication 1786-6.2.
Redundant BNC Cable Connectors
NAP Connector
Pin 1
Channel B
Channel A
Pin #
NAP Signal
1
Signal Common
2
No Connection
3
TX_H
4
TX_L
5
RX_L
6
RX_H
7
No Connection
8
Signal Common
Shell
Earth Ground
Publication 2711-6.1
10-24
Making Terminal Connections
NAP and Redundant Cables
ControlNet cables, taps, connectors. Refer to the ControlNet Cable
System Planning and Installation manual (Publication 1786-6.2.1)
for descriptions of these components. For information on purchasing
these items, refer to the Allen-Bradley ControlNet Cable System
Component List (Publication AG-2.2).
Item
Catalog Number
RG-6 quad-shield
1786-RG6
Coax repeater
1786-RPT, -RPTD
Coax taps
1786-TPR, -TPS, -TPYR, -TPYS
Network access cable
1786-CP
Coax tool kit
1786-CTK
Segment terminators
1786-XT
BNC connectors
1786-BNC, -BNCJ, -BNCP, -BNCJ1
Important: Do not connect to a network using both the redundant
cable BNC connector and the Network Access Port
(NAP).
Publication 2711-6.1
Making Terminal Connections
DeviceNet Terminal Connections
10-25
This chapter describes connections for the DeviceNet PanelView
terminals including:
•
DeviceNet connectors
•
typical DeviceNet network
DeviceNet Terminal Ports
The DeviceNet versions of the PanelView terminals (catalog numbers
ending in 10) have a DeviceNet port and an RS-232 serial port.
•
Use the DeviceNet port to connect to devices on a DeviceNet
network.
•
Use the RS-232 port to transfer applications between a computer
and the terminal or to connect a printer.
For details on connecting to the RS-232 port, see the last section
in this chapter.
PanelView 900 shown
5
1
DeviceNet Port
RS-232 Port
Making DeviceNet Connections
Use one of the cables below to connect the DeviceNet version of the
PanelView terminal to a DeviceNet network.
Cable
Publication No.
DeviceNet Cable, 50 meters (164 feet)
1485C-P1A50
DeviceNet Cable, 100 meters (328 feet)
1485C-P1A150
DeviceNet Cable, 150 meters (492 feet)
1485C-P1A300
Important: Refer to DeviceNet Cable System Planning and
Installation manual (Publication 1485-6.7.1) for network
layout and design information
DeviceNet
Terminal Block
1
Terminal
Signal
Function
Color
1
COM
Common
Black
2
CAN_L
Signal Low
Blue
3
SHIELD
Shield
Uninsulated
4
CAN_H
Signal High
White
5
VDC+
Power Supply
Red
5
Publication 2711-6.1
10-26
Making Terminal Connections
Typical DeviceNet Network
Below is a typical DeviceNet network with PanelView terminals
installed on 2 of the network drops.
A DeviceNet network requires a 24V dc power supply. DeviceNet
power consumption is 24mA - 90mA @24V dc. The PanelView
terminal does not receive its power from the network.
PLC-5
SLC 5/04
or
DeviceNet
Scanner Module
(Catalog No. 1747-SDN)
DeviceNet
Scanner Module
(Catalog No. 1747-SDN)
PanelView
PanelView
RS-232 Port
DeviceNet Port
DeviceNet Port
Serial Link
SM
C
Smart Motor Controller
RediSTATION
Drive
Publication 2711-6.1
Computer for developing
PanelView applications
Making Terminal Connections
DF1 Terminal Connections
10-27
This section describes connections for the DF1 versions of the
PanelView terminal including:
•
compatible controllers
•
DF1 terminal ports
•
connecting to a controller (point-to-point)
•
using a modem
•
connecting to a DeviceNet network
Compatible Controllers
The DF1 terminals support full duplex communications with the
following controllers.
•
SLC, PLC or MicroLogix 1000 via 1761-Net DNI module
•
SLC 5/03, 5/04, or 5/05E (Ethernet version) via Channel 0/DF1
port
•
PLC-5/10, 5/12, 5/15, or 5/25 via bridge such as the 1770-KF2, or
1785-KE
•
PLC-5/11, 5/20, 5/26, 5/40, 5/46, 5/60, 5/80 via Channel 0/DF1
port
•
Ethernet versions of the PLC-5/20E, 5/40E, 5/80E, SLC 5/05E
via Channel 0/DF1 port
•
ControlNet versions of the PLC-5/20C, 5/40C, 5/60C, 5/80C via
Channel 0/DF1 port
DF1 Terminal Ports
The DF1 versions of the PanelView terminals have a DF1 (Full
Duplex) communications port and an RS-232 serial port.
•
Use the DF1 port to communicate with a logic controller using
DF1 full duplex communications.
•
Use the RS-232 serial port to transfer applications between a
computer and the terminal or to connect a printer. For connection
details, see the last section in this chapter.
PanelView 900 shown
DF1 Port
RS-232 File Transfer/Printer Port
Publication 2711-6.1
10-28
Making Terminal Connections
DF1/RS-232 Port Connector
The DF1 port on the PanelView terminal is a 9-pin, male, RS-232
connector. The table below shows the pinout descriptions for this port
and how these pins map to the DF1 ports on the controllers.
DF1 Port
9-pin
DF1 Port
Signal Name
Signal
Description
2
RXD
Receive Data
2
2
4
3
TXD
Transmit Data
3
3
7
4
DTR
Data Terminal
Ready
4
20
5
SG
Signal Ground
5
7
6
DSR
Data Set Ready
6
6
1
SLC
9-pin
PLC
25-pin
MicroLogix/ DNI
8-pin DIN
No Connection
7
RTS
Request to Send
7
4
8
CTS
Clear to Send
8
5
9
2
No Connection
The maximum cable length for DF1/full duplex communications is
15.24 meters (50 feet).
Connecting to a MicroLogix 1000
The following shows a point-to-point connection between the DF1
port of the PanelView terminal and a MicroLogix 1000.
PanelView
AIC+
1761-NET-AIC
MicroLogix 1000
DF1 Port
1761-CBL-HM02
DF1 Port
2711-NC13, -NC14 Cable
The 1761-NET-AIC is used only with the MicroLogix and eliminates
grounding level differences between the controller and PanelView.
Connecting to an SLC or PLC
The following shows a point-to-point connection between the DF1
port of the PanelView terminal and an SLC or PLC controller.
PanelView
SLC 5/03, 5/04, 5/05
DF1 Port
2711-NC13, -NC14 Cable
DF1 Port
PLC 5
2711-NC13, -NC14 Cable
9 to 25-Pin
Adapter
DF1 Port
Use an optical isolator or equivalent when grounding level
differences exist between the controller or modem and the PanelView.
Publication 2711-6.1
Making Terminal Connections
10-29
Using a Modem
Wire or radio modem communications is possible between a DF1
terminal and controller. Each modem must support full duplex
communications. Refer to your modem user manual for details on
settings and configuration.
PanelView
Optical Isolator
DF1 Port
Controller
Modem
Modem
Connecting to a DeviceNet Network
The following illustration shows a DF1 PanelView terminal
connected to a single controller (MicroLogix, SLC or PLC) in a
DeviceNet network.
MicroLogix 1000
DF1 PanelView
DF1
1761-NET DNI Module
1761-NET DNI Module
1761-CBL-HM02
or
DeviceNet
1761-CBL-PM02
SLC 5/03, 5/04, 5/05
1761-CBL-PM02
DF1 port
DF1
Null Modem Cable
24V dc Power Supply
2755-PW46
or
PLC 5/40C
The SLC or PLC requires the PM02 cable.
Only a single processor can be connected.
DF1
Constructing a Null Modem Cable
To construct a null modem cable, refer to the following pinout:
9-pin
25-pin
9-pin
3
TXD
TXD
3
3
2
RXD
RXD
2
2
5
GND
GND
7
5
1
CD
CD
8
1
4
DTR
DTR
20
4
6
DSR
DSR
6
6
8
CTS
CTS
5
8
7
RTS
RTS
4
7
Publication 2711-6.1
10-30
Making Terminal Connections
Connecting a Computer or Printer
to the Terminal
Most of the PanelView terminals have an RS-232 serial port you can
use to:
•
download/upload applications over a serial link
•
and/or connect a printer that supports the IBM enhanced
character set
The illustration below shows how to make these connections.
Communication parameters for the RS-232 port are set on the Printer
Setup screen of the Configuration Mode menu.
Computer
PanelView 900 DH+ Terminal
RS-232 Port
PanelView 550 DH+ Terminal
Available Cables
2711-NC13 5 m (16.4 ft)
2711-NC14 10 m (32.7 ft)
2706-NC13 3 m (10 ft)
9-pin to 25-pin Adapter
(if required)
Printer
RS-232 Port
RS-232 Port
PV550 Printer Port
9-pin male
1 NC
2 TXD or TX1 (Data Transmit)
3 RXD or RX1 (Data Receive)
4 NC
5 GND
6 DSR (pulled high to +12V)
7 NC
8 CTS (pulled high to +12V)
9 NC
Publication 2711-6.1
PV600/900/1000/1400 Printer Port
9-pin male
1 NC
2 TXD or TX1 (Data Transmit)
3 RXD or RX1 (Data Receive)
4 NC
5 GND
6 DSR (pulled high to +12V)
7 RTS or RX2 (Data Receive)
8 CTS or TX2 (Data Transmit
9 NC
Printer/Computer Port
9-pin female
1 DCD
2 RXD (Data Receive)
3 TXD (Data Transmit)
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 NC
Chapter
11
Troubleshooting and Maintenance
Chapter Objectives
This chapter tells how to isolate and correct common operating
problems and perform routine maintenance tasks.
•
equipment required
•
using troubleshooting chart
•
LED indicators
•
cleaning display window
•
replacing clock module
•
replacing backlight
Equipment Required
Other than verifying that the correct power source is connected to the
terminal (use a voltmeter), no electronic diagnostic equipment is
required for troubleshooting.
Using the Troubleshooting Chart
The following pages provide a troubleshooting chart for the terminal.
This chart lists the most common operating problems, causes, and
steps to correct them.
!
ATTENTION: The PanelView terminals contain
hazardous voltages. Do not insert objects or let objects
fall into the terminal through ventilation slots. Always
disconnect power when checking wiring connections.
Failure to take adequate precautions may result in
electrical shock.
Publication 2711-6.1
11-2
Troubleshooting and Maintenance
Troubleshooting Chart
Problem
Probable Cause(s)
Corrective Action(s)
Terminal does not
power up.
Improper connection to power
source.
Verify correct voltage at power terminals on the back of the terminal.
No communications
with SLC or PLC controller.
1. Communications (COMM) fault.
1. Check status of COMM LED.
2. Baud rates not set properly.
3. Controller is not in run mode.
Verify cable connections using
cable diagrams in Chapters 6 - 9.
4. Terminal node and maximum
node numbers are not set correctly.
2. Verify that terminal and controller
are set at the same baud rate.
5. Controller fault.
4. Verify node number settings.
3. Place controller in run mode.
5. Refer to controller user manual.
No communications
with PLC but COMM
LED is green.
1. PanelView is trying to communicate with a controller at a different
address.
1. Verify address of the controller.
2. Change setting of the inhibit bit.
2. The inhibit bit is set as the default
on the Channel Status Screen in
the PLC.
No communications
with computer.
1. Communications (COMM) fault.
2. No SLC, network, or power supply
connection at terminal’s DH-485
port.
3. Baud rates not set correctly.
4. Terminal node and maximum
node numbers are not set correctly.
5. Computer fault.
6. Communication driver not properly loaded.
7. Printer port is enabled.
1. Check status of COMM LED.
Verify cable connections using
cable diagrams in Chapter 10.
2. Personal Computer Interface Converter (PIC) receives power from
DH-485 connection. Verify that the
terminal is connected to an SLC,
network, or wallmount power supply as shown in Chapter 6.
3. Verify that terminal and computer
are set at the correct baud rate.
4. Verify node number settings.
5. Refer to user manual for computer.
6. Refer to RSLinx online help or
manual.
7. Disable printing on the Printer
Setup screen of the Configuration
Mode menu.
Clock Module Battery
Low message is displayed.
Clock module needs replacing.
Replace clock module as described
in instructions provided with clock
module kit.
Cannot transfer application from memory card.
1. Memory card is not properly
installed.
1. Verify correct installation.
2. Application is too large for terminal memory.
3. Check that memory card is properly seated. Application may be
corrupt.
3. Data checksum is incorrect.
4. Invalid file format.
Publication 2711-6.1
2. Reduce size of application file.
4. Verify file format (.PVA) being
transferred.
Troubleshooting and Maintenance
11-3
Problem
Probable Cause(s)
Corrective Action(s)
Cannot transfer application to
memory card.
1. Memory card is not properly
installed.
1. Verify correct installation.
2. Memory card is write protected.1
2. Change memory card protection
switch.
3. File currently exists on memory
3. Erase and reformat card.
card.1
4. Application file is too large, not
enough space on memory card.
1
5. Invalid memory card format.
6. Data checksum is incorrect.
7. Application does not exist.1
4. Reduce size of application file or
erase/format memory card.
5. Replace or reformat memory card. If
problem continues, try another card.
6. Check that card is installed correctly.
If problem continues, try another
card.
7. Check the Terminal Info screen to
verify that an application exists.
Communications problem.
Check status of COMM LED.
See problem ’No communications with
SLC or PLC controller’ for more information.
Application file name appears
as ******* on Terminal Info
screen.
1. Application is invalid.
1. Download application and try again.
2. Application is unusable because
of error.
2. Download new application.
Area on color screen appears
dark.
One of the backlight tubes has burnt
out.
Replace color backlight.
Screen objects are not visible.
1. Correct power is not applied.
1. Verify power connections.
2. Contrast or intensity is not set correctly.
2. Access Screen Setup on the Configuration Mode menu and adjust the
contrast. On keypad terminals,
press the left and right arrow keys
simultaneously, then press [F9] or
[F15].
Screen objects do not function.1
3. Terminal is in screen saver mode.
4. PV550 backlight lamp is not on.
5. Terminal’s backlight is burnt out.
3. Access Screen Setup on the Configuration Mode menu to see if terminal is set for screen saver mode.
4. Access Screen Setup on the Configuration Mode menu and turn on
backlight.
5. Replace backlight.
Values do not update on display but appear as asterisks
****
1. Terminal is not communicating
with controller.
1. Check status of COMM LED.
Refer to problem ’No communication
with SLC or PLC controller’ for more
details.
2. Value is invalid or exceeds the
field width defined for the object.
2. Change the field width for the object.
1
Terminal displays a warning message with instructions if these errors occur.
Publication 2711-6.1
11-4
Troubleshooting and Maintenance
LED Indicators
Use the COMM and Fault LED indicators to isolate operating
problems. The illustration below shows the location of these
indicators.
COMM LED
Fault LED
COMM LED
Fault LED
PV900 Back View
PV600/PV1000 is similar
PV550 Back View
DH-485 and DH+ LED Indications
LED
Comm1
State
Indicates
On (steady
green)
Normal operating state (no communication faults).
Good hardware connection.
Off (power
applied)
Fault detected
• Make sure controller is run mode
• Verify baud settings of terminal and controller
• Verify proper terminal to controller connections
Blinking
No communications established
Off
Normal operating state
On (steady red)
Fault detected. Cycle power to the terminal. If the
fault still exists, the terminal requires servicing.
Flashing
Hardware is functioning but no application is
loaded or the current application is corrupt.
Fault
1
Comm LED stays on until powerup self-tests are complete.
Remote I/O LED Indications
LED
State
On (steady green)
Normal operating state (no communication faults)
Off (power applied)
Communications not functioning
• Verify that baud rate and rack settings match the PLC settings
• Verify proper terminal to controller connections
• Verify that the PLC enables Remote I/O communications
Blinking
No communications established. PLC is in program mode
Comm1
Off
Normal operating state
On (steady red)
Fault detected. Cycle power to the terminal. If the fault still
exists, the terminal requires servicing.
Flashing
Hardware is functioning but no application is loaded or the current application is corrupt.
Fault
1
Publication 2711-6.1
Indicates
Comm LED stays on until powerup self-tests are complete
Troubleshooting and Maintenance
Cleaning the Display Window
11-5
To clean the display window:
!
ATTENTION: Use of abrasive cleansers or solvents
may damage the window. Do not scrub or use brushes.
1. Disconnect power from the terminal at the power source.
2. Use a clean sponge or a soft cloth to clean the display with a mild
soap or detergent.
3. Dry the display with a chamois or moist cellulose sponge to avoid
water spots.
Removing Paint and Grease
Remove fresh paint splashes and grease before drying by rubbing
lightly with isoproply alcohol (70% concentration). Afterward,
provide a final wash using a mild soap or detergent solution. Rinse
with clean water.
Equipment Hose Downs
Be aware that screen objects on touch cell terminals may activate
during equipment hose downs.
!
Replacing the Clock Module
ATTENTION: Because touch terminals have sensitive
touch cell regions, it is possible for screen objects to activate
during equipment hose downs.
The Real-Time Clock (RTC) module contains a lithium battery used
only by the real-time clock. The battery is not used for application
backup or input retention. The clock module has a typical life
expectancy of 7 years.
The clock module replacement kits for the PanelView terminals are
listed in Chapter 1 under Replacement Parts. Replacement
instructions are provided with the kits.
!
Replacing the Backlight
ATTENTION: The clock module contains lithium.
Do not attempt to dispose of the module in a fire or
incinerator. Doing so may cause the clock module to
explode. Follow disposal regulations in your area for
lithium battery disposal.
Replacement backlights are available for the PanelView terminals.
See Replacement Parts in Chapter 1 for the catalog numbers.
Replacement instructions are provided with the kits.
Publication 2711-6.1
11-6
Troubleshooting and Maintenance
Publication 2711-6.1
Appendix
A
Specifications
PanelView 550 Terminals
Electrical
AC Power
Supply Voltage Limits
Power Consumption
85 to 264V ac, 47 to 63 Hz
45 VA maximum
DC Power
Supply Voltage Limits
Power Consumption
Supply Voltage Limits (touch screen only)
Power Consumption (touch screen only)
18 to 30V dc (24V dc nominal)
18 Watts, max. (0.75A @ 24V dc)
18 to 32V dc (24V dc nominal)
18 Watts, max. (0.75A @ 24V dc)
Mechanical
Enclosure
NEMA Type 12/13, 4X (Indoor use only), IP54, IP65
LED Indicators
COMM
Fault
Green
Red
Weight
Keypad, Keypad & Touch
Touch Screen
1.2 kg (2.7 lbs)
.93 kg (2.1 lbs)
Dimensions- Keypad, Keypad & Touch
mm
Inches
167 (H) x 266 (W) x 106 (D)
6.57 (H) x 10.47 (W) x 4.17 (D)
Dimensions- Touch Screen
mm
inches
150 (H) x 183 (W) x 82 (D)
5.92 (H) x 7.21 (W) x 3.20 (D)
Installed Depth- Keypad, Keypad & Touch
86 mm (3.39 inches)
118 mm (4.64 inches) with memory card retainer
207 mm (8.15 inches) with memory card retainer
and clearance to insert and remove memory card
Installed Depth- Touch Screen
64 mm (2.54 inches)
109 mm (4.30 inches) with memory card retainer
207 mm (8.15 inches) with memory card retainer
and clearance to insert and remove memory card
Display
Type
Liquid Crystal Display (LCD)
Size
120 x 60 mm (4.75 x 2.38 in.)
Pixels
256 x 128
Touch Cells
128 (16 columns x 8 rows)
Touch Cell Size
16 x 16 pixels
Terminal Memory
PV550 ( Series E or later) or
PV550T (Series A or later)
Total Application Flash Memory
PV550 (Prior to Series E)
Total Application Flash Memory
240K bytes (application screens)
112K bytes (application screens)
Publication 2711-6.1
A-2
Specifications
Environment
Operating Temperature
0 to 55° C (32 to 131° F)
Storage Temperature
-20 to 70° C (-4 to 158° F)
Relative Humidity (non-condensing)
5 to 95% at 0 to 30° C (32 to 86° F)
5 to 75% at 31 to 40° C (88 to 104° F)
5 to 50% at 41 to 55° C (106 to 131° F)
Heat Dissipation
20 Watts (69 BTU/HR) for AC Power or DC Power
Impulse Shock (operating/non-operating)
30G/50G
Vibration (operating)
2G up to 2,000 Hz
Character Sizes (Pixel size = 0.47 x 0.47 mm)
Size in Pixels
(width x height)
Characters/Row
Maximum Rows
Dimensions in mm
Width x Height
6x8
40
16
2.2 x 3.2
6 x 16
20
16
3.8 x 5.6
6 x 24
13
16
3.8 x 8.4
12 x 8
40
8
7.6 x 2.8
12 x 16
20
8
7.6 x 5.6
12 x 24
13
8
7.6 x 8.4
18 x 8
40
5
11.2 x 2.8
18 x 16
20
5
11.2 x 5.6
18 x 24
13
5
11.2 x 8.4
PanelView 600 Color Terminals
Electrical
AC Power
Supply Voltage Limits
Power Consumption
85 to 264V ac, 43 to 63 Hz
60 VA maximum
DC Power
Supply Voltage Limits
Power Consumption
18 to 32V dc (24V dc nominal)
34 Watts max. (1.4A @ 24V dc)
Mechanical
Enclosure
NEMA Type 12/13, 4X (Indoor use only), IP54, IP65
LED Indicators
COMM
Fault
Green
Red
Weight
2 kg (4.4 lbs)
Dimensions
Installed Depth
Publication 2711-6.1
mm
inches
192 (H) x 290 (W) x 116 (D)
7.55 (H) x 11.40 (W) x 4.57 (D)
99 mm (3.89 inches)
131 mm (5.14 inches) with memory card retainer
220 mm (8.65 inches) with memory card retainer
and clearance to insert and remove memory card
Specifications
A-3
Display
Type
Active Matrix Thin-Film Resistor (TFT) with Cold
Cathode Fluorescent (CCF) Backlight
Size
115 x 86 mm (4.54 x 3.4 in.)
Pixels
320 x 234
Touch Cells
128 (16 columns x 8 rows)
Touch Cell Size
20 x 29 pixels
Terminal Memory
Total Application Flash Memory
240K bytes (application screens)
Environment
Operating Temperature
0 to 55° C (32 to 131° F)
Storage Temperature
-25 to 70° C (-13 to 158° F)
Relative Humidity (non-condensing)
5 to 95% at 0 to 55° C (32 to 131° F)
Heat Dissipation
32 Watts (107 BTU/HR) for AC or DC Power
Impulse Shock (operating/non-operating)
30G/50G
Vibration (operating)
2G up to 2,000 Hz
Terminal Memory
Total Application Flash Memory
240K bytes (application screens)
Environment
Operating Temperature
0 to 55° C (32 to 131° F)
Storage Temperature
-25 to 70° C (-13 to 158° F)
Relative Humidity (non-condensing)
5 to 95% at 0 to 55° C (32 to 131° F)
Heat Dissipation
32 Watts (107 BTU/HR) for AC or DC Power
Impulse Shock (operating/non-operating)
30G/50G
Vibration (operating)
2G up to 2,000 Hz
Character Sizes (Pixel size = 0.36 x 0.37 mm)
Size in Pixels
(width x height)
Dimensions in mm
Width x Height
Characters/Row
Maximum Rows
6x9
52
25
2.9 x 5.9
8 x 16
39
14
2.9 x 5.9
8 x 24
39
9
2.9 x 8.9
16 x 24
19
9
5.8 x 8.9
24 x 32
13
7
8.6 x 11.8
32x 40
9
5
11.5 x 14.8
Publication 2711-6.1
A-4
Specifications
PanelView 900 Monochrome and
Color Terminals
Electrical
AC Power - PV900M and PV900C
Supply Voltage Limits
Power Consumption
85 to 264V ac, 47 to 63 Hz
110 VA maximum
DC Power - PV900M
Supply Voltage Limits
Power Consumption
DC Power - PV900C
Supply Voltage Limits
Power Consumption
18 to 30 V dc (24V dc nominal)
58 Watts max. (2.5A @ 24V dc)
18 to 32 V dc (24V dc nominal)
50 Watts max. (2.1A @ 24V dc)
Mechanical
Enclosure
NEMA Type 12/13, 4X (Indoor use only) IP54, IP65
LED Indicators
COMM
Fault
Green
Red
Weight - PV900M
Keypad
Touch Screen
3.14 kg (4.4 lbs)
2.91 kg (6.4 lbs)
Weight - PV900C
Keypad
Touch Screen
3.18 kg (7.0 lbs)
2.95 kg (6.5 lbs)
Dimensions - PV900M/900C Keypad
Publication 2711-6.1
mm
inches
249 (H) x 406 (W) x 112 (D)
9.80 (H) x 15.97 (W) x 4.40 (D)
Dimensions - PV900M/900C Touch Screen
mm
inches
249 (H) x 336 (W) x 112 (D)
9.80 (H) x 13.24 (W) x 4.40 (D)
Installed Depth - PV900M
97 mm (3.81 inches)
129 mm (5.06 inches) with memory card retainer
220 mm (8.65 inches) with memory card retainer
and clearance to insert and remove memory card
Installed Depth - PV900C
99 mm (3.89 inches)
131 mm (5.14 inches) with memory card retainer
222 mm (8.73 inches) with memory card retainer
and clearance to insert and remove memory card
Specifications
A-5
Display
PV900M
Type
AC Gas Plasma
Size
210 x 131 mm (8.27 x 5.17 in.)
Pixels
640 x 400
Touch Cells
384 (24 columns x 16 rows)
Touch Cell Size
26 x 25 pixels
PV900C
Type
Active Matrix Thin-Film Resistor (TFT) with Cold
Cathode Fluorescent (CCF) Backlight
Size
171 x 130 mm (6.73 x 5.12 in.)
Pixels
640 x 480
Touch Cells
384 (24 columns x 16 rows)
Touch Cell Size
26 x 30 pixels
Terminal Memory
PV900M (prior to Series E)
Total Application Flash Memory
240K bytes (application screens)
PV900M (Series E, firmware 3.0 or later),
PV900C
Total Application Flash Memory
1008K bytes (application screens)
Environment
PV900M
Operating Temperature
0 to 55° C (32 to 131° F)
Storage Temperature
-25 to 70° C (-13 to 158° F)
Relative Humidity (non-condensing)
5 to 85% at 0 to 30° C (32 to 86° F)
Heat Dissipation
50 Watts (165 BTU/HR) for AC Power or
DC Power
Impulse Shock (operating/non-operating)
15G/30G
Vibration (operating)
1G up to 2,000 Hz
PV900C
Operating Temperature
0 to 55° C (32 to 131° F)
Storage Temperature
-25 to 70° C (-13 to 158° F)
Relative Humidity (non-condensing)
5 to 95% at 0 to 55° C (32 to 131° F)
Heat Dissipation
39 Watts (133 BTU/HR)
Impulse Shock (operating/non-operating)
15G/30G
Vibration (operating)
1G up to 2,000 Hz
Publication 2711-6.1
A-6
Specifications
Character Sizes - PV900M (Pixel size = 0.33 x 0.33 mm)
Size in Pixels
(width x height)
8 x 16
Characters/Row
Maximum Rows
79
24
Dimensions in mm
Width x Height
2.6 x 5.3
8 x 24
79
16
2.6 x 7.9
16 x 24
39
16
5.3 x 7.9
24 x 32
26
12
7.9 x 10.6
32x 40
19
9
10.6 x 13.2
Character Sizes - PV900C (Pixel size = 0.27 x 0.27 mm)
Size in Pixels
(width x height)
8 x 16
Publication 2711-6.1
Characters/Row
Maximum Rows
79
24
Dimensions in mm
Width x Height
2.2 x 4.3
8 x 24
79
19
2.2 x 6.5
16 x 24
39
19
4.3 x 6.5
24 x 32
26
14
6.5 x 8.6
32x 40
19
11
8.6 x 10.8
Specifications
A-7
PanelView 1000 Grayscale and
Color Terminals
Electrical
AC Power - PV1000G and PV1000C
Supply Voltage Limits
Power Consumption
85 to 264V ac, 47 to 63 Hz
100 VA maximum
DC Power - PV1000G
Supply Voltage Limits
Power Consumption
DC Power - PV1000C
Supply Voltage Limits
Power Consumption
18 to 32 V dc (24V dc nominal)
40 Watts max. (1.7A @ 24V dc)
18 to 32 V dc (24V dc nominal)
50 Watts max. (2.1A @ 24V dc)
Mechanical
Enclosure
NEMA Type 12/13, 4X (Indoor use only) IP54, IP65
LED Indicators
COMM
Fault
Green
Red
Weight - PV1000G
Keypad
Touch
3.27 kg (7.2 lbs)
3.18 kg (7.0 lbs)
Weight - PV1000C
Keypad
Touch Screen
3.72 kg (8.2 lbs)
3.58 kg (7.9 lbs)
Dimensions-PV1000G/1000C Keypad
mm
inches
Dimensions - PV1000G/1000C Touch Screen
mm
inches
282 (H) x 423 (W) x 112 (D)
11.11 (H) x 16.64 (W) x 4.40 (D)
282 (H) x 370 (W) x 112 (D)
11.11 (H) x 14.58 (W) x 4.40 (D)
Installed Depth - PV1000G
97 mm (3.81 inches)
129 mm (5.06 inches) with memory card retainer
220 mm (8.65 inches) with memory card retainer
and clearance to insert and remove memory card
Installed Depth - PV1000C
99 mm (3.89 inches)
131 mm (5.14 inches) with memory card retainer
222 mm (8.73 inches) with memory card retainer
and clearance to insert and remove memory card
Terminal Memory
Total Application Flash Memory
1008K bytes (application screens)
Publication 2711-6.1
A-8
Specifications
Display
PV1000G
Type
Electroluminescent
Size
211 x 158 mm (8.3 x 6.2 in.)
Pixels
640 x 480
Touch Cells
384 (24 columns x 16 rows)
Touch Cell Size
26 x 30 pixels
PV1000C
Type
Active Matrix Thin-Film Resistor (TFT) with Cold
Cathode Fluorescent (CCF) Backlight
Size
211 x 158 mm (8.3 x 6.2 in.)
Pixels
640 x 480
Touch Cells
384 (24 columns x 16 rows)
Touch Cell Size
26 x 30 pixels
Environment
Operating Temperature
0 to 55° C (32 to 131° F)
Storage Temperature
-25 to 70° C (-13 to 158° F)
Relative Humidity (non-condensing)
5 to 95% at 0 to 55° C (32 to 131° F)
Heat Dissipation
39 Watts (132 BTU/HR) for Grayscale and Color
Impulse Shock (operating/non-operating)
15G/30G
Vibration (operating)
2G up to 2,000 Hz
Character Sizes - PV1000G and PV1000C (Pixel size = 0.33 x 0.33 mm)
Size in Pixels
(width x height)
Publication 2711-6.1
Dimensions in mm
Width x Height
Characters/Row
Maximum Rows
8 x 16
79
24
8 x 24
79
19
2.6 x 7.9
16 x 24
39
19
5.3 x 7.9
24 x 32
26
14
7.9 x 10.6
32x 40
19
11
10.6 x 13.2
2.2 x 5.3
Specifications
A-9
PanelView 1400 Color Terminals
Electrical
AC Power
Supply Voltage Limits
Power Consumption
85 to 264V ac, 43 to 63 Hz
200 VA maximum
Mechanical
Enclosure
NEMA Type 12/13, 4X (Indoor use only) IP54, IP65
LED Indicators
COMM
Fault
Green
Red
Weight
Keypad
Touch Screen
20.3 kg (44.75 lbs)
19.6 kg (43.2 lbs)
Dimensions - PV1400 Keypad
mm
iinches
355 (H) x 483 (W) x 394 (D)
13.97 (H) x 19.0 (W) x 15.53 (D)
Dimensions - PV1400 Touch Screen
mm
inches
Installed Depth
355 (H) x 441 (W) x 394 (D)
13.97 (H) x 17.37 (W) x 15.53 (D)
370 mm (14.58 inches)
400 mm (15.75 inches) with clearance to insert
and remove memory card
Terminal Memory
Total Application Flash Memory
1008K bytes (application screens)
Display
Type
Color CRT
Size
255 x 191 mm (10.0 x 7.5 in.)
Pixels
800 x 600
Touch Cells
384 (24 columns x 16 rows)
Touch Cell Size
33 x 37 pixels
Environment
Operating Temperature
0 to 55° C (32 to 131° F)
Storage Temperature
-40 to 85° C (-40 to 185° F)
Relative Humidity (non-condensing)
5 to 95% at 0 to 55° C (32 to 131° F)
Heat Dissipation
78 Watts (264 BTU/HR)
Impulse Shock (operating/non-operating)
15G/30G
Vibration (operating)
1G up to 2,000 Hz
Publication 2711-6.1
A-10
Specifications
Character Sizes - PV1400 (Pixel size = 0.32 x 0.32 mm)
Size in Pixels
(width x height)
Characters/Row
Dimensions in mm
Width x Height
Maximum Rows
8 x 20
99
29
2.5 x 6.4
16 x 24
49
24
5.1 x 7.6
24 x 32
33
18
7.6 x 10.2
32 x 40
24
14
10.2 x 12.7
32 x 64
24
9
10.2 x 20.4
Communications
DH-485 Network
Baud Rate
Distance Maximum
1200, 2400, 9600, 19.2K
1219 meters (4,000 feet)
DH+ Network
Baud Rate
Distance Maximum
57.6K, 115.2K, 230.4K
3048 meters (10,000 feet)
RS-232 or DH-485 Point-to-Point
Baud Rates
Distance Maximum
1200, 2400, 9600, 19.2K
6.1 meters (20 feet)
Remote I/O
Baud Rates
Publication 2711-6.1
57.6K, 2,800 meters (10,000 feet)
115.2K, 1,400 meters (5,000 feet)
DeviceNet
Baud Rates
125K, 250K, 500K
ControlNet Network
Baud Rate
Distance Maximum
5M
1,000 meters (3,280 feet)
DF1/Full Duplex Communications
Baud Rate
Distance Maximum
1200, 2400, 4800, 9600, 19.2K
15.24 meters (50 feet)
RS-232 Printer Port
Baud Rates
Parity
Data Bits
Stop Bits
Handshaking
1200, 2400, 9600, 19.2K
None, Even, Odd
7 or 8
1 or 2
None, Software (XON, XOFF), Hardware
Specifications
Agency Certifications
A-11
See Nameplate label on each terminal for certifications.
550
600
900M
Emissions (Class B: Light Industrial) EN50081- 1:1992
900C
1000G
ä1
ä1
1000C
1400
ä1
Emissions (Class A: Industrial)
EN50081-2:1993
ä
ä
ä
Immunity (Industrial)
EN50082-2:1995
ä
ä
ä
ä
ä
ä
ä
Programmable Controllers
Equipment Requirements and
Tests) EN61131 2:1995
ä
ä
ä
ä
ä
ä
ä
Low Voltage Directive
(Safety Sections of EN61131-2)
ä
ä
ä
ä
ä
ä
ä
UL508
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
UL1604 Class 1, Div 2,
Groups A, B, C, D, T4
ä
2,4
ä
ä
ä
3
UL2279 (IEC79-15) Class 1,
Zone 2, Groups IIC, T4
ä
ä
ä
DEMKO prEN5002 1 Ex Na
Group IIC, T4
ä
ä
ä
CSA 22.2, No. 142
CSA 22.2, No. 213 Class 1,
Div 2, Groups A, B, C, D, T4
ä
ä
2,4
ä
ä
ä
ä
ä
ä
ä3
ä
ä
ä
ä
1
DeviceNet PanelView terminals are Class A for Emissions
PV550 (Series C or later) or PV550 Touch Screen Only (Series A or later)
3
PV900M (Series C or later)
4 All PV550 terminals have a Temperature Code Rating of T2
2
Publication 2711-6.1
A-12
Specifications
Publication 2711-6.1
Appendix
B
Messages, Codes and Self-Test Numbers
This appendix lists:
Types of Terminal Messages
•
terminal messages and codes that may appear during terminal
operation
•
description of self-test numbers
Status Messages
Indicate the terminal is performing an operation that may limit access
to the terminal, such as an application download or a communication
problem. The message disappears when the terminal completes the
operation or when the condition is satisfied.
Reminder Messages
Indicate a minor fault or mistake. Reminder messages appear when an
invalid operation is attempted, such as entering an out-of-range value.
Pressing any key removes the message.
Warning Messages
Indicate the operation may produce undesirable results. You must
respond to warning messages as indicated in the message.
Fault Messages
Indicate the terminal has detected a condition which prevents further
operation. The current application will halt. The terminal must be
reset (power cycled) to recover from this type of error.
Publication 2711-6.1
B-2
Messages, Codes and Self-Test Numbers
Terminal Messages
Error Number
Terminal Messages
200-206, 300,
318-321, 328,
329, 331, 346,
347, 355, 356,
358, 367, 404,
411, 416, 417,
421-425, 447449, 457, 459,
700, 1105,
1111, 1113,
1115, 12071211, 20022009, 2016,
2018, 2021,
2028 and
20229
A fault has occurred.
Error = X
208
Write to logic controller failed
303
Aborted.
304
File read access
error
305
File write access
error
307
File not supported
308
Meaning
Recommended Action
Minor Fault
or
Terminal Fault
A minor fault was detected that
could impact terminal operation or a terminal fault was
detected.
Press any key to recover from
a minor fault. For terminal
faults, contact technical support with the error code.
Come Status
Controller does not accept data
from the terminal. Controller is
not connected.
Check connections (on
Remote I/O units). Verify that
controller is in run mode and
not busy. Verify that controller
data files are not in use by
other applications.
Reminder/File
Transfer Status
The terminal received an abort
command during a file transfer.
Try again.
Reminder
Error reading the source file
from a source device.
Try again. If problem continues,
contact technical support.
Reminder
Error writing source file.
Try again. If problem continues,
contact technical support.
Reminder/File
Transfer Status
File is incompatible with the
terminal’s firmware.
Contact technical support to
verify compatibility. File must
be a .PVA file.
Timeout
Reminder / File
Transfer Status
The terminal was waiting for
the partner device in a file
transfer, but the terminal timed
out before the data or expected
reply was received.
Check cable connections or
data corruption with noise on
cable. Verify that the computer
was not reset. Try again.
Data corrupted. Verify file and retry.
Reminder/File
Transfer Status
The data checksum has failed
in a file transfer.
Check electrical and cable connections. Try the file transfer
again.
312
Unknown device
Reminder / File
Transfer Status
Destination or source device is
invalid for a read or write application transfer.
Verify the file type entered. Try
again.
313
File too large
Reminder/File
Transfer Status
File too large to be transferred
to the terminal. In a memory
card transfer, the card does not
have enough space.
Reduce application size. See
Appendix A for terminal
requirements. If copying to a
card, check card space.
314
No Card Inserted
Reminder
You tried to transfer data to/
from a memory card but there
is no card in the card slot.
Install a memory card and try
again.
309-311
Publication 2711-6.1
Type
Messages, Codes and Self-Test Numbers
Error Number
Terminal Message
Type
B-3
Meaning
Recommended Action
Reminder
Memory card is unformatted,
contains an unrecognizable
format or is corrupt.
Reformat the card or replace it
with a new card if corrupt. Try
again.
315
Unformatted card
316
Write Protected Card
Reminder / File
Transfer Status
A write command to the card
failed because the card switch
is in the protected mode.
Select write mode by changing
the switch on the top edge of
the card. Try again.
317
File exists. Cannot
overwrite
Reminder/File
Transfer Status
See message 342. This message only occurs when the file
cannot be renamed.
Change the file name or save
to a new memory card.
323
No application on PV
terminal
Reminder/File
Transfer Status
You tried to load an application
on a memory card but there is
no application in the terminal.
View the Terminal Info screen
to see if an application is
loaded in the terminal.
324
Check card status
Reminder/File
Transfer Status
Problem formatting the memory card.
Try a new memory card.
325
Unformatted card
Reminder
Memory card is unformatted,
contains an unrecognizable
format or is corrupt.
Reformat the card or replace it
with a new card. Try again.
326
No Card Inserted
Reminder
You tried to transfer data to/
from a memory card but there
is no card in the card slot.
Install a memory card and try
again.
327
No files
Reminder
You tried to transfer a file from
the memory card but there are
no files on the card.
Use memory card containing
application (.PVA) files.
330
Write Protected Card
Reminder / File
Transfer Status
A write command to the card
failed because the card switch
is in protected mode.
Select write mode by changing
the switch on the top edge of
the card. Try again.
332
No application on PV
terminal
Reminder/File
Transfer Status
You tried to load an application
on a memory card but there is
no application in the terminal.
View the Terminal Info screen
to see if an application is
loaded in the terminal.
333
File in use - Request
denied
Reminder
Attempt to format memory card
containing a file used by the
application. This usually occurs
when an application requires a
font file on the memory card.
Format the memory card on a
computer or a PanelView terminal that does not have an
application loaded.
334
Unexpected card
removal. Please disconnect card before
removal.
Reminder / File
Transfer Status
You removed the memory card
during normal operation and
did not press the Disconnect
button on the Memory Card
configuration screen.
Press the Disconnect Card button to close the files on the
card. When prompted, remove
the card from the slot and then
re-insert the card. Enter Configuration Mode and press the
Run Mode button.
340
Format erases entire
card:
0 or F1 Abort
1 or F2 - Continue
Warning
Operator pressed [F4] Erase /
Format Card on the Memory
Card configuration screen.
Enter appropriate response:
0 or F1 to abort
1 or F2 to continue
341
Proceed with download?
0 or F1 -Abort
1 or F2 - Continue
Warning
You pressed [F2], Restore
From Card on the Memory
Card configuration screen.
Enter appropriate response:
0 or F1 to abort
1 or F2 to continue
Publication 2711-6.1
B-4
Messages, Codes and Self-Test Numbers
Error Number
Terminal Message
Type
Meaning
Recommended Action
342
The PVA File exists.
0 or F1 -Abort
1 or F2 - Upload
with new PVA filename
You pressed [F3], Save To
Card on the Memory Card configuration screen when the file
exists on the card.
Enter appropriate response:
0 or F1 to abort
1 or F2 to upload new PVA
file.
361
Value not in range
Entered value is outside of
valid range.
Enter a value within the valid
range.
364
Closing Files . . .
Status
Terminal is preparing for
removal of memory card.
Wait for files to close before
removing memory card.
365
Remove card . . .
Reminder
You must remove the memory
card for the terminal to continues operation.
Remove the memory card.
366
Card disconnection
will require card
removal to continue
operation.
Warning
Attempt to disconnect the
memory card.
After memory card is disconnected it must be removed
from card slot before the terminal will operate.
File is incompatible with the
terminal’s firmware.
Contact technical support to
verify compatibility. File must
be a .PVA file.
Reminder / File
Transfer Status
Reminder
392-396
File not supported
Reminder/File
Transfer Status
415
Retained memory
lost.
Presets were
loaded.
Reminder
The battery backed memory
was invalid during startup. The
system defaulted to preset values instead of the last states.
No action necessary. Terminal
reverts to defaults.
436
Logic Controller has
screen control
Reminder
You tried to change the application screen but it is configured for controller only access.
No action required, controller
will change screens as programmed.
DH-485 Messages
Error Number
Terminal Message
Type
Meaning
Recommended Action
612
No active node(s)
found on network
Comm Status
No other DH-485 devices can
be located on the network.
Verify that the PanelView terminal and SLC are correctly connected to the system. If the
error occurs. again, check the
node addresses, baud rates,
and maximum node
addresses. Reset the terminal.
613
Required network
node(s) not found
Comm Status
1. If the message is flashing,
the terminal is trying to read
or write one or more SLC
files that are unavailable.
1. The files do not exist on
SLC. Create files on SLC.
2. The network is active, but
SLCs are not located at the
expected nodes. Node and
maximum node numbers
may not be set correctly.
2. Verify that the SLC(s)
required by the application
are at the expected node
addresses with the communication parameters set
properly.
615
Duplicate node
address
Comm Status
More than one node was
assigned the same address.
Verify all device nodes.
616
Data errors on the
link
Comm Status
Corrupt data packets were
detected on DH-485 network.
Verify controller addressing
and baud rate settings. Check
for loose or reversed wiring.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
B-5
ControlLogix Messages
(See Terminal Codes for messages below)
Error Number
634
Terminal Message
Write Fail
Type
Comm Status
Meaning
Recommended Action
ControlLogix Tag or address
does not exist or is the wrong
data type.
Check tag address.
Designated slot does not contain a ControlLogix Processor.
634
Read Fail
Comm Status
ControlLogix Tag or address
does not exist or is the wrong
data type.
Designated slot does not contain a ControlLogix Processor.
Check for data type mismatch.
Verify ControlLogix slot location.
Check tag address.
Check for data type mismatch.
Verify ControlLogix slot location.
ControlNet Messages
(See Terminal Codes for messages below)
634
PanelView offline
Comm Warning
PanelView is offline.
Check connections
634
Write fail.
Comm Warning
PanelView is communicating
with the controller. The data
table address does not exist.
Check / define data table
address in the controller.
634
Write timeout.
Comm Warning
PanelView is not communicating with the logic controller.
Check connections and node
configuration in the application.
634
Read fail.
Comm Warning
PanelView is communicating
with the controller. The data
table address does not exist.
Check/define data table
address in the controller.
634
Read timeout.
Comm Warning
PanelView is not communicating with the controller.
Check/define data table
address in the controller.
636
Initial write failed.
Reminder
Write to Logic Controller on
Startup was configured and on
powerup, the PanelView could
not write initial values to a
node’s data table address.
or
Write to Logic Controller on
Startup was not configured and
the PanelView was unable to
write a controller. Note: The
error is only displayed on the
first write attempt.
Check/define data table
address in the controller.
Check communication connections and node configuration in
the application.
Publication 2711-6.1
B-6
Messages, Codes and Self-Test Numbers
Remote I/O Messages
Error Number
Terminal Message
Type
Meaning
Recommended Action
661
Timeout - No Block
Transfer Writes
Comm Status
The PLC is communicating
with the terminal, but the PanelView is not receiving BTW
requests required by the application.
Check ladder logic for missing
BTW instructions (instructions
are not enabled) or addressing
errors. Check for logic controller errors.
662
Timeout - No Block
Transfer Reads
Comm Status
The PLC is communicating
with the terminal, but the PanelView is not receiving BTR
requests required by the application.
Check ladder logic for missing
BTR instructions (instructions
are not enabled) or addressing
errors. Check for logic controller errors.
663
No PLC communications
Comm Status
The PLC is not communicating.
Possible causes are disconnected cable, no power to PLC,
incorrect baud rate or rack settings for PLC configuration.
COMM LED is off.
Check for pulled cables and
PLC power. Check baud rate
settings and rack configurations.
Check wiring of connector.
Communication resumes when
problem is corrected.
664
PLC in program
mode
Comm Status
The PLC is offline (in Program
Mode). The COMM LED on the
Configuration Mode menu a g.
Place the PLC in run mode to
resume communication.
665
Timeout - No Block
Transfer Requests
Comm Status
The PLC is communicating
with the terminal, but the PanelView is not receiving BTR or
BTW requests required by the
application.
Check ladder logic for missing
BTR or BTW instructions
(instructions are not enabled)
or addressing errors. Check for
logic controller errors.
666
Invalid Rack Configuration
Comm Status
No communications can occur
because of an invalid rack configuration.
Correct the RIO rack configuration.
667
Remote I/O Hardware Failed
Comm Status
During startup, the terminal
detected a missing, corrupt or
nonfunctional Remote I/O card.
The terminal will run but not
communicate.
Contact technical support and
provide specific message.
DH+ Messages
Error Number
Terminal Message
Type
Meaning
Recommended Action
675
Required network
node(s) not found
Comm Status
The network is active, but the
logic controller(s) are not
located at the expected nodes.
Verify that the logic controller(s) required by the application are at the expected node
addresses and that the communication parameters are set
properly.
676
File access error
1. The terminal is trying to
access one or more controller data files that are
unavailable.
1. The data files do not exist
on the controller. Create
the data files.
2. If the message is flashing,
the terminal is trying to read
or write data files that are
unavailable.
2. The data file is smaller than
what is required. For example, the PanelView uses
N7:10 but only N7:0 is
defined in the controller.
Publication 2711-6.1
Comm Status
Messages, Codes and Self-Test Numbers
Error Number
Terminal Message
677
Unstable DH+ network
678
679
Type
B-7
Meaning
Recommended Action
Comm Status
Corrupt data packets or intermittent system configuration
was detected on DH+ network.
Verify all controller addressing
and baud rate settings. Check
for loose or reversed wiring.
Duplicate node
detected
Comm Status
More than one node was
assigned the same address.
Verify all device nodes.
No active Node(s)
found on network
Comm Status
No other DH+ devices can be
located on the network.
Verify that PanelView terminal
and logic controller(s) are correctly connected to the system.
Check cable and wiring.
If error continues, verify that
baud rates on the terminal and
controller are the same. Communication resumes when the
problem is corrected.
681
DH+ hardware failed
Comm Status
During startup, the terminal
detected a missing, corrupt, or
nonfunctional DH+ card. The
terminal will run but not communicate.
Contact technical support and
provide the specific terminal
message.
1109
Font file unavailable,
Font error = ****
Minor Fault or
Terminal Fault
You downloaded an application
to the PanelView without the
appropriate memory card (containing the font file) inserted in
the card slot of the terminal.
From the Memory Card screen,
press the Disconnect button to
close the files on the card.
Remove the card from the card
slot. Locate the card containing
the font file or copy the correct
font file to a card. Insert the
correct memory card in the
card slot and enter Run mode.
1110
No valid application
Reminder
You tried to run an application
that has not been downloaded
to the terminal.
Download application to terminal.
2005
Application file:
Insufficient RAM
Terminal Fault
Application file may be too
large.
Try again. If possible, reduce
the size of the application.
Application file contains errors
Terminal Fault
Application contains incompatible data.
Check application and try
again.
Reminder
The battery backed memory
was invalid during startup. The
system defaulted to preset values instead of the last states.
No action necessary. Terminal
reverts to defaults.
2007 - 2010
2011
Retained memory
lost. Presets were
loaded.
2012
Application file: Too
many retained memory devices
Terminal Fault
The battery-backed RAM is too
full to hold all devices requiring
presets.
Reduce the number of control
objects. Use global objects.
2014
Hardware configuration is corrupted
Terminal Fault
The terminal hardware configuration is corrupt.
Contact technical support.
2030, 2031
Hardware and firmware do not match
Terminal Fault
A mismatch exists between the
terminal firmware and the terminal hardware.
Verify that the series and revision markings on the back of
the terminal are compatible
with the firmware.
Publication 2711-6.1
B-8
Messages, Codes and Self-Test Numbers
Terminal Codes
Terminal Codes are displayed on the PanelView terminal during
operation or terminal configuration.
DeviceNet Codes
These codes appear as a banner at the top of an application screen or
as an LED status on the terminal’s Configuration screen. Error 634
appears in upper left of banner. Codes less than 10 are minor faults
and clear automatically when corrected. Codes above 10 require a
terminal reset to clear.
DeviceNet
Comm Status
Code
Publication 2711-6.1
Indicates:
Recommended Action
1
No connections established. Occurs on
power-up until a device connection is
established on the network.
Establish a connection over DeviceNet to the
PanelView.
2
A connection is in the timed out state.
Occurs once I/O messaging is stopped
after an I/O connection has been running.
Check the network wiring and that the master
device (scanner) is operational.
3
An Explicit-Client tag cannot be obtained.
Occurs if the device associated with an
Explicit-Client tag is not responding or the
peer tag does not exist at the specified
class, instance, and attribute number.
Check the data location is correct and that the
end device is attached and operational. For
write tags, ensure that the appropriate attribute
is targeted. If the targeted device is UCMM
capable, ensure it has enough explicit message
connections to allow the PanelView to take one.
If the targeted device is not UCMM capable,
ensure that it is owned by a Master device
(scanner).
4
A zero length I/O message was received
placing the I/O application in idle mode.
Occurs when the scanner is in program
mode.
Error clears when switched back to run. Correct
the problem of the Master sending the I/O idle
condition.
5
Message Overrun. Message traffic from
the PanelView is being generated quicker
than it is possible to send the data. Occurs
with large I/O sizes when Change-OfState is being used and state changes are
occurring very quickly or if polling too fast.
Slow down I/O polling or the state changes generating change of state I/O messages. Use
cyclic I/O at a fast heartbeat rate rather than
change-of-state. Use the production inhibit
capability on the master.
11
No network power detected. Occurs if network 24V is not present.
Check the wiring and termination resistors and
make sure the baud rate is correct. Reset the
terminal.
12
Dup MAC Failure. Occurs if the PanelView
powers up with the same Node Address
present on the network.
Change the node address to an used address.
13
Bus-off Interrupt occurred. CAN Chip is
held in reset. Caused by noise on network
signal lines or an attempt to connect to the
network at the wrong baud rate.
Check baud rate and network wiring, including
termination resistors. Reset the terminal.
Messages, Codes and Self-Test Numbers
B-9
These codes appear as a box in the middle of the screen. Error 636
appears in the upper left corner. Operation of the terminal continues.
Alert messages can be cleared.
DeviceNet
Alert Code
Indicates:
Recommended Action
2
Unsupported DeviceNet Message received. The Network Access Object received a message that is not
supported.
Should not occur in normal operation. Clear
the message. If problem re-occurs, contact
Allen-Bradley.
3
Initial Writes Failure. The Motherboard failed to send
all input data to the daughter card prior to network
startup.
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact Allen-Bradley.
4
Invalid Explicit-Client Address. Occurs at runtime if
the node address associated with the Explicit-Client
tag is the same as the PanelView.
Clear the message and determine which tag
in the application is pointing to the PanelView’s node address. Correct the application.
7
Change-Of-State Input Overrun. Occurs if PanelView
state changes on I/O input data occurred faster than
the PanelView could send them to the I/O scanner.
Clear the message. Excessive network traffic
could cause this problem if inputs are
changing rapidly.
8
Identity Object Reset Service received over
DeviceNet. Occurs if an external device sends an
Identify Object Reset Service to the PanelView.
An external network device has requested a
PanelView terminal reset. Press a key to clear
the alarm.
10
Unsupported DeviceNet message received.
Should not occur during normal operation.
Clear the message. If problem reoccurs,
contact Allen-Bradley.
12
Invalid ASA Number (0x00000000 or 0xFFFFFFFF).
Occurs if the flash memory is corrupt or an invalid
ASA number was programmed.
Clear the message. The message occurs
each time the terminal is reset. The terminal
operates normally but you should correct the
problem. Contact Allen-Bradley.
13
Invalid Screen Context Priority received.
Should not occur in normal operation. Clear
the message. If problem reoccurs, contact
Allen-Bradley.
14
Get Next Scan Item Failed in peer mode.
Should not occur in normal operation. Clear
the message. If problem reoccurs, contact
Allen-Bradley.
15
Explicit-Client Input Data not received. Will occur if an
input (push button) changes a second time before its
previous state was sent on the network. Only for
Explicit-Client Tags.
Clear the message. Excessive network traffic
could cause this problem if inputs are changing rapidly. Handle high speed input data over
I/O connections if possible. Also make sure
the addressed attribute exists and can be set
on the network.
16
I/O Connection Size does not match size of I/O data in
Assembly Instances 1 & 2. Programmed connection
sizes for I/O do not match the amount of data represented by the I/O type tags.
Clear the message and if the problem
reoccurs, consult Allen-Bradley.
19
Get Next Contact Request Failure. In Explicit-Client
Mode scanning, the request to obtain the next tag in
current context failed.
Should not occur in normal operation. Clear
the message. If problem reoccurs, contact
Allen-Bradley.
Publication 2711-6.1
B-10
Messages, Codes and Self-Test Numbers
ControlLogix Codes
ControlLogix
Terminal
Alert Code
Alert Type
Indicates:
Recommended Action(s)
603
Critical fault
File download error
Reset the terminal. If problem occurs
again, contact Allen-Bradley for technical support.
9020
Critical fault
An internal fault occurred.
Reset the terminal. If problem occurs
again, contact Allen-Bradley for technical support.
ControlNet Codes
These errors appear at the top of the application screen or on the
terminal’s configuration screen. If you should get an alert number that
is not listed, contact Allen-Bradley for technical support.
ControlNet
Indicates:
Recommended Action(s)
The communications device has
completed the request to force the
device into the listen-only state.
The PanelView was detected as having a duplicate node address and is
in the listen-only mode. Check the
node address (MAC ID) of the
devices on the network to verify that
addresses are not duplicated.
Warning
The PanelView was forced to a listenonly state.
Contact Allen-Bradley for technical
support.
Warning
A fixed tag packet was received but
there is no place to route the packet.
The data packet is discarded and the
error message is displayed.
Contact Allen-Bradley for technical
support.
Warning
An attempt was made to open an
unsupported transport class.
Contact Allen-Bradley for technical
support.
1829
Warning
An attempt was made to open a
Class 1 transport with application
triggering or a Class 3 transport with
cyclic triggering.
Contact Allen-Bradley for technical
support.
3333
Warning
A connection has timed out.
A file transfer was unexpectedly interrupted. Try to transfer again.
Error Code
1803
1824
1826
1828
Publication 2711-6.1
Alert Type
Informational
Messages, Codes and Self-Test Numbers
B-11
These messages appear on the terminal screen as DC Error = xx. If
you get an alert number that is not listed here, contact Allen-Bradley
for technical support.
ControlNet
Alert Code
Alert Type
Indicates:
Recommended Action(s)
9000
Critical fault
Interface startup failed.
Contact Allen-Bradley for technical
support.
9003
Critical fault
CIP S/N is not valid.
Contact Allen-Bradley for technical
support.
9004
Critical fault
Out of buffers.
Contact Allen-Bradley for technical
support.
9010
Critical fault
Invalid target node, target node is the
same as the PanelView, or larger
than the UMAX.
Check node address of all devices on
the network including the PanelView
terminal.
9012
Communications Warning
ControlNet object received a reset
request.
Contact Allen-Bradley for technical
support.
9014
Critical fault
A fatal CPU fault occurred.
Contact Allen-Bradley for technical
support.
9015
Critical fault
A ControlNet hardware fault
occurred.
Contact Allen-Bradley for technical
support.
9016
Critical fault
RAM verification failed at startup.
Contact Allen-Bradley for technical
support.
9017
Critical fault
CRC verification failed at startup.
Contact Allen-Bradley for technical
support.
9018
Critical fault
A critical internal error occurred.
Contact Allen-Bradley for technical
support.
9019
Critical fault
An internal fault occurred.
Reset terminal, if problem occurs
again, contact Allen-Bradley for technical support.
9020
Critical fault
An internal fault occurred.
Reset terminal. If problem occurs
again, reload application. If problem
persists, contact Allen-Bradley for
technical support.
Publication 2711-6.1
B-12
Messages, Codes and Self-Test Numbers
Remote I/O Communication Loss
When communication fails on a Remote I/O network:
•
Object states are maintained and the message "No PLC
Communication" is displayed on the screen.
•
If Block Transfers are defined for the application, but no BTR or
BTW instructions are received, another message appears when
the Block Transfer Timeout occurs.
These messages continue to display until communications is
established. If a write operation is attempted to the logic program
controlling the PanelView objects, the terminal will display the
message "Error: Write to Logic Controller failed".
If a PanelView object is activated during a communication loss, the
object retains its new state and sends this state value to the controller
when communications is established.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
Self-test Numbers
B-13
The self-test numbers appear on the screen during powerup.
COPYRIGHT ALLEN-BRADLEY COMPANY
1999, ALL RIGHTS RESERVED VXX.XX
TESTING VERIFICANADO PRUFEN
VERIFICATION AUTOTEST
2
Self-test Number
Test Number
Indicates
1
STATIC RAM test
2
Terminal searching for a file to download.
10
Erase boot flash area.
11
Copy boot code
12
Boot code copy successful
13
Boot code copy failed. Check for error after boot code is
copied to the onboard flash EPROM.
20
Erase firmware from flash EPROM
21
Copy firmware to firmware flash memory
22
Firmware copy successful
23
Firmware copy failed
24
Performed CRC base firmware check
25
Firmware not compatible with boot code
26
Firmware not compatible with hardware
30
Watchdog test
31
Stuck key test
32
Real time clock test
33
LCD RAM failed
34
Performed CRC extended firmware check
Note: You may not see all of these test numbers during a powerup.
If a test fails, the terminal displays:
ERROR!
FEHLER!
ERREUR!
ERRORE!
The following test numbers appear only if a problem occurs.
Test Number
Indicates
40
No executable code to run after boot
50
Wrong memory card format
60
CPU could not execute code
Publication 2711-6.1
B-14
Messages, Codes and Self-Test Numbers
The table below shows fault conditions that may occur during
powerup.
Publication 2711-6.1
Fault Indicator
Indicates
Solid Red
Static RAM Test failed. Contact technical
support.
Blinking Red
(6 times per second)
Checksum test on boot code failed. Contact technical support.
Blinking Red
(5 seconds on/5 seconds off)
Boot code is incorrect for terminal type
(touch screen or keypad). Contact technical support.
Appendix
C
European Union Directive Compliance
If the PanelView Operator Terminals are installed within the European
Union or EEA regions and have the CE mark, the following regulations
apply.
EMC and Low Voltage Directives
These apparatuses are tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC), and amending directives 91/
263/EEC, 92/31/EEC, 93/68/EEC; 72/23/EEC Low Voltage
Directive, and amending directive 93/68/EEC using the following
standards, in whole or in part:
550
600
900M
Emissions (Class B: Light Industrial)
EN50081- 1:1992
900C
1000G
ä
ä
1
1000C
1400
ä1
1
Emissions (Class A: Industrial)
EN50081-2:1993
ä
ä
ä
Immunity (Industrial) EN50082-2:1995
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
ä
DEMKO prEN5002 1 Ex Na Group IIC, T4
ä
1
DeviceNet PanelView terminals are Class A for Emissions
ä
ä
Programmable Controllers
Equipment Requirements and Tests)
EN61131 2:1995
Low Voltage Directive
(Safety Sections of EN61131-2)
ä
Intended Use of Product
According to these Standards, the factor which determines, for EMC
purposes, whether a product is deemed to be "Industrial" rather than
"Residential, commercial or light industrial", is given in clause 1 of
EN50081-2 as follows:
Apparatus covered by this standard is not intended for connection
to a public mains network supplied from a high- or mediumvoltage transformer dedicated for the supply of an installation
feeding a manufacturing or similar plant.
When installed in Europe, any other application is in contravention of
European Union Directives, and a breach of these laws.
The PanelView 900 color, the 1000 grayscale and the 1400 terminals
are certified for direct connection to a low-voltage public mains
supply or to a dedicated source, which is intended to interface to a
low-voltage public mains supply.
Publication 2711-6.1
C-2
European Union Directive Complaince
Wiring Recommendations
To reduce electrical noise, connect the PanelView terminal to its own
branch circuit. The input power source should be protected by a fuse
or circuit breaker rated no more than 15 amps. Route incoming power
to the PanelView terminal by a separate path from the
communications cable.
Where power and communication lines must cross, they should cross
at right angles. Communication lines can be installed in the same
conduit as low level DC I/O lines (less than 10 Volts).
Declaration Conformity
Declarations of Conformity are available upon request for the
PanelView terminals. Contact your local Allen-Bradley
representative or distributor and request the following Allen-Bradley
corporate numbers:
Publication 2711-6.1
•
43500-218-01 for the PanelView 550 keypad or keypad & touch
screen terminals
•
43500-219-01 for the DC power versions of the above PanelView
550 terminals
•
43500-307-01 for the PanelView 550 touch screen only terminals
•
43500-260-01 for the PanelView 600 terminals
•
43500-177-01 for the PanelView 900 monochrome terminals
•
43500-235-01 for the PanelView 900 color terminals
•
43500-274-01 for the PanelView 1000 grayscale terminals
•
43500-279-01 for the PanelView 1000 color terminals
•
43500-269-01 for the PanelView 1400 terminals
Glossary
Glossary
adapter
ControlNet device which responds to scanner messages (also called
slave device).
address
1) A character string that uniquely identifies a memory location. 2) A
character string that uniquely identifies the physical location of an
input or output circuit.
application
In the context of PanelBuilder, an application is a logical arrangement
of screens which replace the functions of a control panel and consist
of push buttons, data entry objects, control lists and indicators. The
application runs in a PanelView terminal.
application file
File containing configuration information for a PanelView terminal.
Files exist in either a PanelView (.PVA) or a PanelBuilder (.PBA)
format. Files transferred to a terminal are in a .PVA format. Files
within PanelBuilder are in a .PBA format.
ATA card
Advanced Technology Attachment (ATA), Intelligent Drive
Electronics (IDE), PC Cards (formerly PCMCIA) combine the drive
controller and memory storage device. ATA cards can be accessed
with standard Copy or Delete commands on a computer. The card
looks like a hard drive to the user. You can use the card on a variety
of computers without any special setup.
baud
A unit of signaling speed equal to the number of discrete conditions
or signal events per second.Where one bit is encoded on each
signalling event, the number of baud is the same as the number of
bit/s.
boot revision
Revision number of the terminal boot code.
bridge
Device that allows network data to pass from one link to another link.
controller
A unit, such as a programmable controller or relay panel, that controls
machine or process elements.
Publication 2711-6.1
G-2
Glossary
cursor keys
Up, down, left, right arrows on the terminal keypad. These keys are
used to move a selection cursor or the active object indicator bar.
DF1
Allen-Bradley communication protocol based on an ANSI X3.281976 specification.
cursor keys
Up, down, left, right arrows on the terminal keypad. These keys are
used to move a selection cursor or the active object indicator bar.
download
See upload/download.
DH-485 link
Data Highway 485 link. An Allen-Bradley token-passing carrier-band
link for a local area network.
DH+ link
Data Highway Plus link. An Allen-Bradley token-passing baseband
link for a local area network.
EMI
Electromagnetic Interference. Any electromagnetic disturbance that
interrupts, obstructs, or otherwise impairs the performance of
electronic equipment.
EPROM
Erasable Programmable Read-only Memory. A PROM that can be
erased, usually with ultraviolet light, then re-programmed with
electrical signals. As with all PROMs, it is nonvolatile random-access
memory.
EEPROM (flash)
Electrically-Erasable PROM. A type of PROM that can be erased and
re-programmed by electrical signals. As with all PROMs, it is
nonvolatile random-access memory. Used by the PanelView
terminals to stored applications.
firmware
Logic stored in read-only memory.
function keys
Set of keys (labeled F1-F10, F1-F16 or F1-21) on the PanelView
terminals used to initiate functions. The function keys are userdefined and may have custom labels.
Publication 2711-6.1
Glossary
G-3
interscan delay
Determines the amount of time the PanelView waits before re-reading
the current screen data from the logic controller.
keeper
The network controller of a ControlNet network.
keypad
Set of 14 keys (numeric 0-9, decimal point, backspace, minus, and
enter) to the right of the display on keypad terminals. These keys are
used to enter data.
LED
Light-Emitting Diode.
Memory Card
A storage medium which can store a PanelView application and/or a
font file.
MicroLogix
An Allen-Bradley programmable controller.
NEMA standards
Consensus standards in the United States for electrical equipment
approved by the members of the National Electrical Manufacturers
Association (NEMA).
network
Collection of connected nodes including the connection paths,
repeaters, and bridges.
Network Access Point (NAP)
Port providing temporary access to a ControlNet network through the
RJ-45 connector.
Network Update Time (NUT)
The ControlNet network update time established for the
communications link.
node
The connection point at which medium access is provided.
PanelBuilder software
A Windows program used to develop applications which run in
PanelView terminals.
PanelView terminal
An Allen-Bradley keypad or touch screen terminal providing the
operator interface to the logic controller when an application is
executing.
Publication 2711-6.1
G-4
Glossary
PC
1) Personal Computer. 2) Programmable Controller. 3) Printed
Circuit.
PCCC
Acronym for Programmable Controller Communication Commands.
PLC controller
1) An Allen-Bradley programmable controller with a name that has
the prefix PLC. See programmable controller.
preset value
A value loaded into a controller data table when an application is first
started.
programmable controller
A solid-state control system that has a user-programmable memory
for storage of instructions to implement specific functions such as I/O
control, logic, timing, counting, report generation, communication,
arithmetic, and data file manipulation. A controller consists of a
central processor, input/output interface, and memory. A controller is
designed as an industrial control system.
real time clock
Internal clock that provides time, day, month and year.
remote I/O
1) I/O connected to a processor across a serial link. With a serial link,
remote I/O can be located long distances from the processor.
remote I/O link
A serial link for carrying I/O data between a PLC or SLC processor/
scanner and remote I/O adapters.
repeater
Two-port component that receives and transmits all data from one
segment to another.
restore
To load an application from a memory (PC) card.
RS-232
An EIA standard that specifies electrical, mechanical, and functional
characteristics for serial binary communication circuits in a point-topoint link.
RS-485
An EIA standard that specifies electrical characteristics of balancedvoltage digital interface circuits in a multi-point link.
Publication 2711-6.1
Glossary
G-5
scheduled messages
Messages that occur at a regular specified interval. They are assigned
a particular portion of the network update time (NUT) and are always
transmitted at that time.
safety extra-low voltage (SELV)
A voltage which, under all operating conditions does not exceed 42.4
V peak or dc between conductors, or between any conductor and
earth, in a circuit which is isolated from the main power supply by
means of a safety isolating transformer or an equivalent means.
National regulations have to be considered for a correct isolation
voltage rating.
scratchpad
A window that appears in the center of the terminal display that
allows data entry using the terminal or screen keypad.
screen
1) the viewing surface on which data is displayed. 2) The visual
image on a screen.
segment
Trunk-cable sections connected through taps with terminators at each
end and no repeaters.
SLC
An Allen-Bradley programmable controller with a name that has the
prefix SLC.
SMAX
Highest ControlNet node address which can communicate during the
scheduled portion of the network update interval.
tap
Hardware component that connects devices to the ControlNet trunk
cable.
touch cell
1 of 128 or 384 rectangular areas on the terminal display that can
sense when touched.
touch screen
The display window of the terminal that responds when touched.
trunk cable
Bus or central part of a cable system.
unscheduled messages
Messages that are sent on an as needed basis. Unscheduled messages
are sent during the unscheduled portion of the network update
interval.
Publication 2711-6.1
G-6
Glossary
UMAX
Highest ControlNet node address which can communicate during the
unscheduled portion of the network update interval.
upload/download
Commonly referred to the reading/writing across a link relatively
large blocks of data from one device to another. Whether it is
considered an upload or download may depend upon whether it is a
read or write and upon which device initiates the transaction. When
data is transferred to a programming device, it is considered an
upload. When data is transferred from a programming device, it is
considered a download.
Publication 2711-6.1
Index
A
AC power
connecting, 2-2–2-4
electrical ratings, 2-2
accessories
antiglare overlay, 1-29
backlight lamp, 1-30
cables, 1-29–1-30
file transfer utility, 1-29
function key legend kits, 1-28
memory card retainer, 1-28
memory cards, 1-28
mounting clips, 1-30
mounting studs, 1-30
real time clock, 1-30
wallmount power supply, 1-29
Comm LED, 3-3, 11-4
communication ports, available, 1-2–1-5
configuration mode menu, 1-26
accessing, 3-2
operations list, 3-2
alarms
content, 5-12
description, 1-27
configuration screens
ControlNet, 3-10
DeviceNet, 3-12
DF1, 3-14
DH+, 3-8
DH-485, 3-6
language selection, 3-4
memory card transfers, 3-5
preset operations, 3-16
printer setup, 3-26
Remote I/O, 2-9, 3-9
screen setup, 3-18–3-23
terminal information, 3-17
time and date, 3-25
Allen-Bradley, contacting for assistance, P-44
contacting Allen-Bradley, P-44
antiglare overlay, 1-29
control lists, 5-3
activating, 5-3
active item, 5-3
active list, 5-3
cursor, 5-4
list keys, 5-4
piloted, 5-4
selecting an item, 5-5
vertical indicator bar, 5-4
application files
running, 1-24
settings, 3-1
audience, P-43
B
backlight lamps, 1-30
replacing, 11-5
bar graphs, 5-10
boot code revision, 3-17
C
cables
ControlNet, 10-23
DeviceNet, 10-25
DF1, 10-29
DH+, 10-15
DH-485, 1-29, 10-7
DH-485 network, 10-8, 10-9
Remote I/O, 1-30, 10-4
RS-232, 1-30
card, memory, 1-28, 3-5, 4-1
ControlNet communications
active node, 3-10
available terminals, 1-2–1-5
channel status, 3-11
communication status, 3-10
compatible controllers, 10-21
connecting a printer, 10-30
ControlNet ports, 10-21
ControlNet protocol, 10-20
firmware revision, 3-10
interscan delay, 3-10
making connections, 10-23
new node, 3-10
related information, 10-20
serial number, 3-10
typical network, 10-22
certifications, A-11
cleaning, display window, 11-5
Publication 2711-6.1
I-ii
Index
D
data entry
keypad enable button, 5-6
numeric entry cursor point, 5-6
scratchpad, 5-6
date and time setup, 3-25
DC power
connecting, 2-5–2-6
electrical ratings, 2-5
declarations of conformity, C-2
degaussing PanelView 1400
enabling/disabling, 3-23
setting schedule, 3-23
DeviceNet communications
active baud rate, 3-12
active node, 3-12
available terminals, 1-2–1-5
bus-off interrupt, 3-13
connecting a computer, 10-30
connecting a printer, 10-30
DeviceNet ports, 10-25
input size, 3-13
interscan delay, 3-13
LED indicators, 3-13
making connections, 10-25
new baud rate, 3-12
new node, 3-12
output size, 3-13
DF1 communications
available terminals, 1-2–1-5
baud rate, 3-14
Comm LED, 3-15
compatible controllers, 10-27
configuration screen, 3-14
connecting to a DeviceNet network, 10-29
connecting to a MicroLogix 1000, 10-28
connecting to an SLC or PLC, 10-28
DF1 port pinouts, 10-28
DF1 ports, 10-27
error detection (CRC or BCC), 3-14
handshaking, 3-15
null modem cable, 10-29
serial communication parameters, 3-14
using a modem, 10-29
DH+ communications
available terminals, 1-2–1-5
baud, 3-8
cable, 10-15
configuration screen, 3-8, 3-13
Publication 2711-6.1
connecting a computer, 10-30
connecting a printer, 10-30
DH+ communications port, 10-13
LED indicators, 3-8
making DH+ connections, 10-15
node, 3-8
RS-232 port, 10-13
typical system configuration, 10-14
DH-485 communications
available terminals, 1-1–1-5
baud rate, 3-6
cables, 10-7
configuration screen, 3-6
connecting a computer, 10-10
connecting a printer, 10-30
DH-485 communications port, 10-6
DH-485 programming connector, 10-6
hand-held terminal connection, 10-12
LED indicators, 3-7
link coupler, 10-8, 10-9
maximum node, 3-6
MicroLogix connection, 10-9
network connection, 10-8
node address, 3-6
ports, 10-6
power supply, 10-10
RS-232 port, 10-6
SLC connection, 10-7
SLC connection using AIC+, 10-9
display
adjusting settings, 3-18–3-23
cleaning window, 11-5
displays
color, 1-1
grayscale, 1-1
monochrome, 1-1
E
European Union Directive Compliance, P-43,
C-1
F
Fault LED, 3-3, 11-4
fault messages, B-1
file transfer utility, 1-29
firmware revision, 3-17
font files, 3-17, 4-8
function key legend kits, 1-25, 1-28
Index
I
K
indicators
bar graphs, 5-10
list indicators, 5-10
multistate indicators, 5-10
key repeat
delay, 3-16
rate, 3-16
initial screen, 2-8
keypad terminals
available options, 1-1–1-5
operation, 1-25
installation of terminals, P-43, P-44
Installing the PanelView 1000
clearances, 8-4
cutout dimensions, 8-5
enclosures, 8-1
hazardous locations, 8-1
mounting dimensions, 8-3
panel installation, 8-6
required tools, 8-2
Installing the PanelView 1400
clip mounting, 9-5
cutout dimensions, 9-4
enclosures, 9-1
mounting dimensions, 9-2
required tools, 9-1
stud mounting, 9-7
Installing the PanelView 550
clearances, 6-3
cutout dimensions, 6-4
enclosures, 6-1
hazardous locations, 6-1
mounting dimensions, 6-2
panel installation, 6-5
required tools, 6-2
Installing the PanelView 600
clearances, 7-3
cutout dimensions, 7-2
enclosures, 7-1
hazardous locations, 7-1
mounting dimensions, 7-2
panel installation, 7-4
required tools, 7-2
Installing the PanelView 900
clearances, 8-4
cutout dimensions, 8-5
enclosures, 8-1
hazardous locations, 8-1
mounting dimensions, 8-2
panel installation, 8-6
required tools, 8-2
I-iii
keypad enable button, 5-6
L
language
selection, 3-4
types, 3-4
LEDs
Comm, 3-3, 11-4
Fault, 3-3, 11-4
link coupler, 1-29, 10-8, 10-9
list indicators, 5-10
list keys
control lists, 5-4
screen selector lists, 5-9
M
manual contents, P-42
memory card, 1-28
closing files on card, 3-5
disconnect button, 3-5
erase and format, 3-5
installation, 4-2
loading application from card, 4-4
loading application onto card, 4-6
removing, 3-5, 4-8
restoring application from card, 3-5
saving application to card, 3-5
storing font files, 4-8
types, 4-1
using retainer, 4-2
viewing applications on card, 3-5
write protection, 11-3, B-3
message displays, 5-11
messages
fault, B-1
general, B-2
reminder, B-1
Remote I/O, B-12
status, B-1
warning, B-1
Publication 2711-6.1
I-iv
Index
mounting clips, 1-30
mounting studs, 1-30
multistate indicators, 5-10
N
numeric data displays, 5-11
numeric entry controls
cursor point, 5-6
description, 5-6
entering data, 5-7
keypad enable button, 5-6
scratchpad, 5-6
P
PanelView 1000
adjusting display intensity, 3-19
connecting AC power, 2-2
connecting DC power, 2-5
features, 1-16
installation, 8-1
resetting, 2-7
screen adjustments, 3-19, 3-22
screen saver, 3-19, 3-22
specifications, A-7
PanelView 1400
adjusting display intensity, 3-24
aligning the touch grid, 3-24
connecting AC power, 2-2
degaussing, 3-23
features, 1-20
installation, 9-1
resetting, 2-7
screen adjustments, 3-23
screen saver, 3-23
specifications, A-9
PanelView 550
adjusting contrast, 3-18
connecting AC power, 2-2
connecting DC power, 2-5
installation, 6-1
resetting, 2-7
screen adjustments, 3-18
specifications, A-1
turning backlight on and off, 3-18
PanelView 600
adjusting display intensity, 3-19
connecting AC power, 2-2
connecting DC power, 2-5
Publication 2711-6.1
features, 1-12
installation, 7-1
resetting, 2-7
screen adjustments, 3-19
screen saver, 3-19
specifications, A-2
PanelView 900
adjusting display intensity, 3-19, 3-20
conditioning the display, 3-21
connecting AC power, 2-2, 2-5
features, 1-16
installation, 8-1
resetting, 2-7
screen adjustments, 3-19, 3-20
screen saver, 3-19, 3-20
specifications, A-4
PanelView terminals
operation, 1-25
types, 1-1
Pass-Through, 2-10, 3-9
personal computer interface converter, 1-29
connecting earth ground, 10-10
PIC converter, 10-10
power connection
AC power, 2-2–2-4
DC power, 2-5–2-6
power supply, 1-29, 10-10
powerup sequence, 2-8
DH-485 terminals, 2-8
Remote I/O terminals, 2-9
RS-232 terminals, 2-8
preset operations
initial values, 3-16
last state values, 3-16
powerup screen, 3-16
preset values, 3-16
restart and load values, 3-16
printer port setup
communication settings, 3-26
configuring, 3-26
enabling/disabling printing, 3-27
handshaking, 3-26
port pinout, 10-30
top of form, 3-27
printing, 1-26, 5-12
Index
push buttons
hold time, 5-2
operation, 5-2
R
real time clock, 1-30
replacement, 11-5
reminder messages, B-1
Remote, 3-9
Remote I/O communications
available terminals, 1-2–1-5
baud rate, 2-10, 3-9
block transfer timeout, 2-10
cable, 10-4
configuration screen, 3-9
connecting a computer, 10-30
connecting a printer, 10-30
connecting to a Remote I/O scanner, 10-4
last chassis, 2-10, 3-9
out-of-box application, 2-9
Pass-Through, 2-10, 3-9
rack number, 2-10, 3-9
rack size, 2-10, 3-9
Remote I/O port, 10-2
RS-232 port, 10-2
starting module group, 2-10
supported controllers, 10-3
reset video, 3-2
resetting
PanelView 1000, 2-7
PanelView 1400, 2-7
PanelView 550, 2-7
PanelView 600, 2-7
PanelView 900, 2-7
RS-232 (DH-485) communications
available terminals, 1-2–1-5
connecting a computer, 10-18
connecting a printer, 10-30
connecting to DH+ link, 10-19
RS-232 port, 10-16
SLC connection, 10-17
RS-232 serial port
cables, 10-30
configuring, 3-26
connecting a computer, 10-30
connecting a printer, 10-30
port pinout, 10-30
run mode, 3-2
I-v
S
scale, bar graph, 5-10
scratchpad
cancelling, 5-7
entering data, 5-7
screen saver, 3-19–3-23
screen selectors
activating a list, 5-8
description, 5-8
list keys, 5-9
selecting an item, 5-8
vertical indicator bar, 5-9
self-test numbers, 2-8, B-13
specifications
PanelView 1000, A-7
PanelView 1400, A-9
PanelView 550, A-1
PanelView 600, A-2
PanelView 900, A-4
status messages, B-1
T
terminal information
boot revision, 3-17
current application, 3-17
firmware revision, 3-17
font file in use, 3-17
hardware configuration, 3-17
terminal messages, B-2
terminals
installation, P-43, P-44
types, 1-1
terminology, P-43
time and date setup, 3-25
touch screen terminals
available options, 1-2–1-5
troubleshooting
contacting Allen-Bradley, P-44
correcting problems, 11-2
problems, 11-2
terminal messages, B-2
W
wallmount power supply, 1-29, 10-10
warning messages, B-1
write protection
memory card, 11-3, B-3
Publication 2711-6.1
I-vi
Index
Publication 2711-6.1
Publication 2711-6.1 - December 1998
Supersedes Publication 2711-6.1 - July 1997
Supersedes Publication 2711-6.1.3 - April 1998
40061-360-01(D)
 1998 Rockwell International. All Rights Reserved. Printed in USA
">